From: Mauro Carvalho Chehab <mchehab@s-opensource.com>
To: Linux Media Mailing List <linux-media@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>,
Mauro Carvalho Chehab <mchehab@infradead.org>,
Jonathan Corbet <corbet@lwn.net>,
Randy Dunlap <rdunlap@infradead.org>,
"Paul E. McKenney" <paulmck@linux.vnet.ibm.com>,
Kees Cook <keescook@chromium.org>,
linux-doc@vger.kernel.org
Subject: [PATCH 01/18] [media] doc-rst: move bttv documentation to bttv.rst file
Date: Mon, 18 Jul 2016 15:30:23 -0300 [thread overview]
Message-ID: <2287cb47fb6bc16c0f7e08756eb1541204a130de.1468865380.git.mchehab@s-opensource.com> (raw)
In-Reply-To: <cover.1468865380.git.mchehab@s-opensource.com>
In-Reply-To: <cover.1468865380.git.mchehab@s-opensource.com>
There were several files under Documentation/video4linux/bttv.
Instead of simply copying them to the rst folder, I opted to
merge into a single document and adjust the headers to
adjust the section levels and fix the cards tables.
There are two exceptions on the merge:
- The Tuners were renamed as a separate document, as they
describe a separate driver;
- I removed the PROBLEMS section. It describes problems with
the very first generation of 3D boards (Mistique/S3).
It sounds very unlikely that someone would still need to
install a bttv board on such hardware. Also, it is not
very well written, IMHO.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
---
Documentation/media/v4l-drivers/bttv.rst | 1881 ++++++++++++++++++++
.../bttv/Tuners => media/v4l-drivers/tuners.rst} | 0
Documentation/video4linux/bttv/CONTRIBUTORS | 25 -
Documentation/video4linux/bttv/Cards | 960 ----------
Documentation/video4linux/bttv/ICs | 37 -
Documentation/video4linux/bttv/Insmod-options | 172 --
Documentation/video4linux/bttv/MAKEDEV | 27 -
Documentation/video4linux/bttv/Modprobe.conf | 11 -
Documentation/video4linux/bttv/Modules.conf | 14 -
Documentation/video4linux/bttv/PROBLEMS | 62 -
Documentation/video4linux/bttv/README | 90 -
Documentation/video4linux/bttv/README.WINVIEW | 33 -
Documentation/video4linux/bttv/README.freeze | 74 -
Documentation/video4linux/bttv/README.quirks | 83 -
Documentation/video4linux/bttv/Sound-FAQ | 148 --
Documentation/video4linux/bttv/Specs | 3 -
Documentation/video4linux/bttv/THANKS | 24 -
17 files changed, 1881 insertions(+), 1763 deletions(-)
create mode 100644 Documentation/media/v4l-drivers/bttv.rst
rename Documentation/{video4linux/bttv/Tuners => media/v4l-drivers/tuners.rst} (100%)
delete mode 100644 Documentation/video4linux/bttv/CONTRIBUTORS
delete mode 100644 Documentation/video4linux/bttv/Cards
delete mode 100644 Documentation/video4linux/bttv/ICs
delete mode 100644 Documentation/video4linux/bttv/Insmod-options
delete mode 100644 Documentation/video4linux/bttv/MAKEDEV
delete mode 100644 Documentation/video4linux/bttv/Modprobe.conf
delete mode 100644 Documentation/video4linux/bttv/Modules.conf
delete mode 100644 Documentation/video4linux/bttv/PROBLEMS
delete mode 100644 Documentation/video4linux/bttv/README
delete mode 100644 Documentation/video4linux/bttv/README.WINVIEW
delete mode 100644 Documentation/video4linux/bttv/README.freeze
delete mode 100644 Documentation/video4linux/bttv/README.quirks
delete mode 100644 Documentation/video4linux/bttv/Sound-FAQ
delete mode 100644 Documentation/video4linux/bttv/Specs
delete mode 100644 Documentation/video4linux/bttv/THANKS
diff --git a/Documentation/media/v4l-drivers/bttv.rst b/Documentation/media/v4l-drivers/bttv.rst
new file mode 100644
index 000000000000..d7d956835e38
--- /dev/null
+++ b/Documentation/media/v4l-drivers/bttv.rst
@@ -0,0 +1,1881 @@
+The bttv driver
+===============
+
+
+Release notes for bttv
+----------------------
+
+You'll need at least these config options for bttv:
+ CONFIG_I2C=m
+ CONFIG_I2C_ALGOBIT=m
+ CONFIG_VIDEO_DEV=m
+
+The latest bttv version is available from http://bytesex.org/bttv/
+
+
+Make bttv work with your card
+-----------------------------
+
+Just try "modprobe bttv" and see if that works.
+
+If it doesn't bttv likely could not autodetect your card and needs some
+insmod options. The most important insmod option for bttv is "card=n"
+to select the correct card type. If you get video but no sound you've
+very likely specified the wrong (or no) card type. A list of supported
+cards is in CARDLIST.bttv
+
+If bttv takes very long to load (happens sometimes with the cheap
+cards which have no tuner), try adding this to your modules.conf:
+ options i2c-algo-bit bit_test=1
+
+For the WinTV/PVR you need one firmware file from the driver CD:
+hcwamc.rbf. The file is in the pvr45xxx.exe archive (self-extracting
+zip file, unzip can unpack it). Put it into the /etc/pvr directory or
+use the firm_altera=<path> insmod option to point the driver to the
+location of the file.
+
+If your card isn't listed in CARDLIST.bttv or if you have trouble making
+audio work, you should read the Sound-FAQ.
+
+
+Autodetecting cards
+-------------------
+
+bttv uses the PCI Subsystem ID to autodetect the card type. lspci lists
+the Subsystem ID in the second line, looks like this:
+
+00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 (rev 02)
+ Subsystem: Hauppauge computer works Inc. WinTV/GO
+ Flags: bus master, medium devsel, latency 32, IRQ 5
+ Memory at e2000000 (32-bit, prefetchable) [size=4K]
+
+only bt878-based cards can have a subsystem ID (which does not mean
+that every card really has one). bt848 cards can't have a Subsystem
+ID and therefore can't be autodetected. There is a list with the ID's
+in bttv-cards.c (in case you are intrested or want to mail patches
+with updates).
+
+
+Still doesn't work?
+-------------------
+
+I do NOT have a lab with 30+ different grabber boards and a
+PAL/NTSC/SECAM test signal generator at home, so I often can't
+reproduce your problems. This makes debugging very difficult for me.
+If you have some knowledge and spare time, please try to fix this
+yourself (patches very welcome of course...) You know: The linux
+slogan is "Do it yourself".
+
+There is a mailing list: linux-media@vger.kernel.org
+http://vger.kernel.org/vger-lists.html#linux-media
+
+If you have trouble with some specific TV card, try to ask there
+instead of mailing me directly. The chance that someone with the
+same card listens there is much higher...
+
+For problems with sound: There are a lot of different systems used
+for TV sound all over the world. And there are also different chips
+which decode the audio signal. Reports about sound problems ("stereo
+does'nt work") are pretty useless unless you include some details
+about your hardware and the TV sound scheme used in your country (or
+at least the country you are living in).
+
+Modprobe options
+----------------
+
+Note: "modinfo <module>" prints various information about a kernel
+module, among them a complete and up-to-date list of insmod options.
+This list tends to be outdated because it is updated manually ...
+
+==========================================================================
+
+bttv.o
+
+::
+
+ the bt848/878 (grabber chip) driver
+
+ insmod args:
+ card=n card type, see CARDLIST for a list.
+ tuner=n tuner type, see CARDLIST for a list.
+ radio=0/1 card supports radio
+ pll=0/1/2 pll settings
+ 0: don't use PLL
+ 1: 28 MHz crystal installed
+ 2: 35 MHz crystal installed
+
+ triton1=0/1 for Triton1 (+others) compatibility
+ vsfx=0/1 yet another chipset bug compatibility bit
+ see README.quirks for details on these two.
+
+ bigendian=n Set the endianness of the gfx framebuffer.
+ Default is native endian.
+ fieldnr=0/1 Count fields. Some TV descrambling software
+ needs this, for others it only generates
+ 50 useless IRQs/sec. default is 0 (off).
+ autoload=0/1 autoload helper modules (tuner, audio).
+ default is 1 (on).
+ bttv_verbose=0/1/2 verbose level (at insmod time, while
+ looking at the hardware). default is 1.
+ bttv_debug=0/1 debug messages (for capture).
+ default is 0 (off).
+ irq_debug=0/1 irq handler debug messages.
+ default is 0 (off).
+ gbuffers=2-32 number of capture buffers for mmap'ed capture.
+ default is 4.
+ gbufsize= size of capture buffers. default and
+ maximum value is 0x208000 (~2MB)
+ no_overlay=0 Enable overlay on broken hardware. There
+ are some chipsets (SIS for example) which
+ are known to have problems with the PCI DMA
+ push used by bttv. bttv will disable overlay
+ by default on this hardware to avoid crashes.
+ With this insmod option you can override this.
+ no_overlay=1 Disable overlay. It should be used by broken
+ hardware that doesn't support PCI2PCI direct
+ transfers.
+ automute=0/1 Automatically mutes the sound if there is
+ no TV signal, on by default. You might try
+ to disable this if you have bad input signal
+ quality which leading to unwanted sound
+ dropouts.
+ chroma_agc=0/1 AGC of chroma signal, off by default.
+ adc_crush=0/1 Luminance ADC crush, on by default.
+ i2c_udelay= Allow reduce I2C speed. Default is 5 usecs
+ (meaning 66,67 Kbps). The default is the
+ maximum supported speed by kernel bitbang
+ algorithm. You may use lower numbers, if I2C
+ messages are lost (16 is known to work on
+ all supported cards).
+
+ bttv_gpio=0/1
+ gpiomask=
+ audioall=
+ audiomux=
+ See Sound-FAQ for a detailed description.
+
+ remap, card, radio and pll accept up to four comma-separated arguments
+ (for multiple boards).
+
+tuner.o
+
+::
+
+ The tuner driver. You need this unless you want to use only
+ with a camera or external tuner ...
+
+ insmod args:
+ debug=1 print some debug info to the syslog
+ type=n type of the tuner chip. n as follows:
+ see CARDLIST for a complete list.
+ pal=[bdgil] select PAL variant (used for some tuners
+ only, important for the audio carrier).
+
+tvaudio.o
+
+::
+
+ new, experimental module which is supported to provide a single
+ driver for all simple i2c audio control chips (tda/tea*).
+
+ insmod args:
+ tda8425 = 1 enable/disable the support for the
+ tda9840 = 1 various chips.
+ tda9850 = 1 The tea6300 can't be autodetected and is
+ tda9855 = 1 therefore off by default, if you have
+ tda9873 = 1 this one on your card (STB uses these)
+ tda9874a = 1 you have to enable it explicitly.
+ tea6300 = 0 The two tda985x chips use the same i2c
+ tea6420 = 1 address and can't be disturgished from
+ pic16c54 = 1 each other, you might have to disable
+ the wrong one.
+ debug = 1 print debug messages
+
+ insmod args for tda9874a:
+ tda9874a_SIF=1/2 select sound IF input pin (1 or 2)
+ (default is pin 1)
+ tda9874a_AMSEL=0/1 auto-mute select for NICAM (default=0)
+ Please read note 3 below!
+ tda9874a_STD=n select TV sound standard (0..8):
+ 0 - A2, B/G
+ 1 - A2, M (Korea)
+ 2 - A2, D/K (1)
+ 3 - A2, D/K (2)
+ 4 - A2, D/K (3)
+ 5 - NICAM, I
+ 6 - NICAM, B/G
+ 7 - NICAM, D/K (default)
+ 8 - NICAM, L
+
+ Note 1: tda9874a supports both tda9874h (old) and tda9874a (new) chips.
+ Note 2: tda9874h/a and tda9875 (which is supported separately by
+ tda9875.o) use the same i2c address so both modules should not be
+ used at the same time.
+ Note 3: Using tda9874a_AMSEL option depends on your TV card design!
+ AMSEL=0: auto-mute will switch between NICAM sound
+ and the sound on 1st carrier (i.e. FM mono or AM).
+ AMSEL=1: auto-mute will switch between NICAM sound
+ and the analog mono input (MONOIN pin).
+ If tda9874a decoder on your card has MONOIN pin not connected, then
+ use only tda9874_AMSEL=0 or don't specify this option at all.
+ For example:
+ card=65 (FlyVideo 2000S) - set AMSEL=1 or AMSEL=0
+ card=72 (Prolink PV-BT878P rev.9B) - set AMSEL=0 only
+
+msp3400.o
+
+::
+
+
+ The driver for the msp34xx sound processor chips. If you have a
+ stereo card, you probably want to insmod this one.
+
+ insmod args:
+ debug=1/2 print some debug info to the syslog,
+ 2 is more verbose.
+ simple=1 Use the "short programming" method. Newer
+ msp34xx versions support this. You need this
+ for dbx stereo. Default is on if supported by
+ the chip.
+ once=1 Don't check the TV-stations Audio mode
+ every few seconds, but only once after
+ channel switches.
+ amsound=1 Audio carrier is AM/NICAM at 6.5 Mhz. This
+ should improve things for french people, the
+ carrier autoscan seems to work with FM only...
+
+tea6300.o - OBSOLETE (use tvaudio instead)
+
+::
+
+ The driver for the tea6300 fader chip. If you have a stereo
+ card and the msp3400.o doesn't work, you might want to try this
+ one. This chip is seen on most STB TV/FM cards (usually from
+ Gateway OEM sold surplus on auction sites).
+
+ insmod args:
+ debug=1 print some debug info to the syslog.
+
+tda8425.o - OBSOLETE (use tvaudio instead)
+
+::
+
+ The driver for the tda8425 fader chip. This driver used to be
+ part of bttv.c, so if your sound used to work but does not
+ anymore, try loading this module.
+
+ insmod args:
+ debug=1 print some debug info to the syslog.
+
+tda985x.o - OBSOLETE (use tvaudio instead)
+
+::
+
+ The driver for the tda9850/55 audio chips.
+
+ insmod args:
+ debug=1 print some debug info to the syslog.
+ chip=9850/9855 set the chip type.
+
+
+If the box freezes hard with bttv
+---------------------------------
+
+It might be a bttv driver bug. It also might be bad hardware. It also
+might be something else ...
+
+Just mailing me "bttv freezes" isn't going to help much. This README
+has a few hints how you can help to pin down the problem.
+
+
+bttv bugs
+~~~~~~~~~
+
+If some version works and another doesn't it is likely to be a driver
+bug. It is very helpful if you can tell where exactly it broke
+(i.e. the last working and the first broken version).
+
+With a hard freeze you probably doesn't find anything in the logfiles.
+The only way to capture any kernel messages is to hook up a serial
+console and let some terminal application log the messages. /me uses
+screen. See Documentation/serial-console.txt for details on setting
+up a serial console.
+
+Read Documentation/oops-tracing.txt to learn how to get any useful
+information out of a register+stack dump printed by the kernel on
+protection faults (so-called "kernel oops").
+
+If you run into some kind of deadlock, you can try to dump a call trace
+for each process using sysrq-t (see Documentation/sysrq.txt).
+This way it is possible to figure where *exactly* some process in "D"
+state is stuck.
+
+I've seen reports that bttv 0.7.x crashes whereas 0.8.x works rock solid
+for some people. Thus probably a small buglet left somewhere in bttv
+0.7.x. I have no idea where exactly, it works stable for me and a lot of
+other people. But in case you have problems with the 0.7.x versions you
+can give 0.8.x a try ...
+
+
+hardware bugs
+~~~~~~~~~~~~~
+
+Some hardware can't deal with PCI-PCI transfers (i.e. grabber => vga).
+Sometimes problems show up with bttv just because of the high load on
+the PCI bus. The bt848/878 chips have a few workarounds for known
+incompatibilities, see README.quirks.
+
+Some folks report that increasing the pci latency helps too,
+althrought I'm not sure whenever this really fixes the problems or
+only makes it less likely to happen. Both bttv and btaudio have a
+insmod option to set the PCI latency of the device.
+
+Some mainboard have problems to deal correctly with multiple devices
+doing DMA at the same time. bttv + ide seems to cause this sometimes,
+if this is the case you likely see freezes only with video and hard disk
+access at the same time. Updating the IDE driver to get the latest and
+greatest workarounds for hardware bugs might fix these problems.
+
+
+other
+~~~~~
+
+If you use some binary-only yunk (like nvidia module) try to reproduce
+the problem without.
+
+IRQ sharing is known to cause problems in some cases. It works just
+fine in theory and many configurations. Neverless it might be worth a
+try to shuffle around the PCI cards to give bttv another IRQ or make
+it share the IRQ with some other piece of hardware. IRQ sharing with
+VGA cards seems to cause trouble sometimes. I've also seen funny
+effects with bttv sharing the IRQ with the ACPI bridge (and
+apci-enabled kernel).
+
+Bttv quirks
+-----------
+
+Below is what the bt878 data book says about the PCI bug compatibility
+modes of the bt878 chip.
+
+The triton1 insmod option sets the EN_TBFX bit in the control register.
+The vsfx insmod option does the same for EN_VSFX bit. If you have
+stability problems you can try if one of these options makes your box
+work solid.
+
+drivers/pci/quirks.c knows about these issues, this way these bits are
+enabled automagically for known-buggy chipsets (look at the kernel
+messages, bttv tells you).
+
+Normal PCI Mode
+~~~~~~~~~~~~~~~
+
+The PCI REQ signal is the logical-or of the incoming function requests.
+The inter-nal GNT[0:1] signals are gated asynchronously with GNT and
+demultiplexed by the audio request signal. Thus the arbiter defaults to
+the video function at power-up and parks there during no requests for
+bus access. This is desirable since the video will request the bus more
+often. However, the audio will have highest bus access priority. Thus
+the audio will have first access to the bus even when issuing a request
+after the video request but before the PCI external arbiter has granted
+access to the Bt879. Neither function can preempt the other once on the
+bus. The duration to empty the entire video PCI FIFO onto the PCI bus is
+very short compared to the bus access latency the audio PCI FIFO can
+tolerate.
+
+
+430FX Compatibility Mode
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+When using the 430FX PCI, the following rules will ensure
+compatibility:
+
+ (1) Deassert REQ at the same time as asserting FRAME.
+ (2) Do not reassert REQ to request another bus transaction until after
+ finish-ing the previous transaction.
+
+Since the individual bus masters do not have direct control of REQ, a
+simple logical-or of video and audio requests would violate the rules.
+Thus, both the arbiter and the initiator contain 430FX compatibility
+mode logic. To enable 430FX mode, set the EN_TBFX bit as indicated in
+Device Control Register on page 104.
+
+When EN_TBFX is enabled, the arbiter ensures that the two compatibility
+rules are satisfied. Before GNT is asserted by the PCI arbiter, this
+internal arbiter may still logical-or the two requests. However, once
+the GNT is issued, this arbiter must lock in its decision and now route
+only the granted request to the REQ pin. The arbiter decision lock
+happens regardless of the state of FRAME because it does not know when
+FRAME will be asserted (typically - each initiator will assert FRAME on
+the cycle following GNT). When FRAME is asserted, it is the initiator s
+responsibility to remove its request at the same time. It is the
+arbiters responsibility to allow this request to flow through to REQ and
+not allow the other request to hold REQ asserted. The decision lock may
+be removed at the end of the transaction: for example, when the bus is
+idle (FRAME and IRDY). The arbiter decision may then continue
+asynchronously until GNT is again asserted.
+
+
+Interfacing with Non-PCI 2.1 Compliant Core Logic
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+A small percentage of core logic devices may start a bus transaction
+during the same cycle that GNT is de-asserted. This is non PCI 2.1
+compliant. To ensure compatibility when using PCs with these PCI
+controllers, the EN_VSFX bit must be enabled (refer to Device Control
+Register on page 104). When in this mode, the arbiter does not pass GNT
+to the internal functions unless REQ is asserted. This prevents a bus
+transaction from starting the same cycle as GNT is de-asserted. This
+also has the side effect of not being able to take advantage of bus
+parking, thus lowering arbitration performance. The Bt879 drivers must
+query for these non-compliant devices, and set the EN_VSFX bit only if
+required.
+
+bttv and sound mini howto
+-------------------------
+
+There are a lot of different bt848/849/878/879 based boards available.
+Making video work often is not a big deal, because this is handled
+completely by the bt8xx chip, which is common on all boards. But
+sound is handled in slightly different ways on each board.
+
+To handle the grabber boards correctly, there is a array tvcards[] in
+bttv-cards.c, which holds the information required for each board.
+Sound will work only, if the correct entry is used (for video it often
+makes no difference). The bttv driver prints a line to the kernel
+log, telling which card type is used. Like this one:
+
+ bttv0: model: BT848(Hauppauge old) [autodetected]
+
+You should verify this is correct. If it isn't, you have to pass the
+correct board type as insmod argument, "insmod bttv card=2" for
+example. The file CARDLIST has a list of valid arguments for card.
+If your card isn't listed there, you might check the source code for
+new entries which are not listed yet. If there isn't one for your
+card, you can check if one of the existing entries does work for you
+(just trial and error...).
+
+Some boards have an extra processor for sound to do stereo decoding
+and other nice features. The msp34xx chips are used by Hauppauge for
+example. If your board has one, you might have to load a helper
+module like msp3400.o to make sound work. If there isn't one for the
+chip used on your board: Bad luck. Start writing a new one. Well,
+you might want to check the video4linux mailing list archive first...
+
+Of course you need a correctly installed soundcard unless you have the
+speakers connected directly to the grabber board. Hint: check the
+mixer settings too. ALSA for example has everything muted by default.
+
+
+How sound works in detail
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Still doesn't work? Looks like some driver hacking is required.
+Below is a do-it-yourself description for you.
+
+The bt8xx chips have 32 general purpose pins, and registers to control
+these pins. One register is the output enable register
+(BT848_GPIO_OUT_EN), it says which pins are actively driven by the
+bt848 chip. Another one is the data register (BT848_GPIO_DATA), where
+you can get/set the status if these pins. They can be used for input
+and output.
+
+Most grabber board vendors use these pins to control an external chip
+which does the sound routing. But every board is a little different.
+These pins are also used by some companies to drive remote control
+receiver chips. Some boards use the i2c bus instead of the gpio pins
+to connect the mux chip.
+
+As mentioned above, there is a array which holds the required
+information for each known board. You basically have to create a new
+line for your board. The important fields are these two:
+
+struct tvcard
+{
+ [ ... ]
+ u32 gpiomask;
+ u32 audiomux[6]; /* Tuner, Radio, external, internal, mute, stereo */
+};
+
+gpiomask specifies which pins are used to control the audio mux chip.
+The corresponding bits in the output enable register
+(BT848_GPIO_OUT_EN) will be set as these pins must be driven by the
+bt848 chip.
+
+The audiomux[] array holds the data values for the different inputs
+(i.e. which pins must be high/low for tuner/mute/...). This will be
+written to the data register (BT848_GPIO_DATA) to switch the audio
+mux.
+
+
+What you have to do is figure out the correct values for gpiomask and
+the audiomux array. If you have Windows and the drivers four your
+card installed, you might to check out if you can read these registers
+values used by the windows driver. A tool to do this is available
+from ftp://telepresence.dmem.strath.ac.uk/pub/bt848/winutil, but it
+does'nt work with bt878 boards according to some reports I received.
+Another one with bt878 support is available from
+http://btwincap.sourceforge.net/Files/btspy2.00.zip
+
+You might also dig around in the *.ini files of the Windows applications.
+You can have a look at the board to see which of the gpio pins are
+connected at all and then start trial-and-error ...
+
+
+Starting with release 0.7.41 bttv has a number of insmod options to
+make the gpio debugging easier:
+
+bttv_gpio=0/1 enable/disable gpio debug messages
+gpiomask=n set the gpiomask value
+audiomux=i,j,... set the values of the audiomux array
+audioall=a set the values of the audiomux array (one
+ value for all array elements, useful to check
+ out which effect the particular value has).
+
+The messages printed with bttv_gpio=1 look like this:
+
+ bttv0: gpio: en=00000027, out=00000024 in=00ffffd8 [audio: off]
+
+en = output _en_able register (BT848_GPIO_OUT_EN)
+out = _out_put bits of the data register (BT848_GPIO_DATA),
+ i.e. BT848_GPIO_DATA & BT848_GPIO_OUT_EN
+in = _in_put bits of the data register,
+ i.e. BT848_GPIO_DATA & ~BT848_GPIO_OUT_EN
+
+
+
+Other elements of the tvcards array
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+If you are trying to make a new card work you might find it useful to
+know what the other elements in the tvcards array are good for:
+
+video_inputs - # of video inputs the card has
+audio_inputs - historical cruft, not used any more.
+tuner - which input is the tuner
+svhs - which input is svhs (all others are labeled composite)
+muxsel - video mux, input->registervalue mapping
+pll - same as pll= insmod option
+tuner_type - same as tuner= insmod option
+*_modulename - hint whenever some card needs this or that audio
+ module loaded to work properly.
+has_radio - whenever this TV card has a radio tuner.
+no_msp34xx - "1" disables loading of msp3400.o module
+no_tda9875 - "1" disables loading of tda9875.o module
+needs_tvaudio - set to "1" to load tvaudio.o module
+
+If some config item is specified both from the tvcards array and as
+insmod option, the insmod option takes precedence.
+
+Cards
+-----
+
+.. note::
+ For a more updated list, please check
+ https://linuxtv.org/wiki/index.php/Hardware_Device_Information
+
+Supported cards: Bt848/Bt848a/Bt849/Bt878/Bt879 cards
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+All cards with Bt848/Bt848a/Bt849/Bt878/Bt879 and normal
+Composite/S-VHS inputs are supported. Teletext and Intercast support
+(PAL only) for ALL cards via VBI sample decoding in software.
+
+Some cards with additional multiplexing of inputs or other additional
+fancy chips are only partially supported (unless specifications by the
+card manufacturer are given). When a card is listed here it isn't
+necessarily fully supported.
+
+All other cards only differ by additional components as tuners, sound
+decoders, EEPROMs, teletext decoders ...
+
+
+MATRIX Vision
+~~~~~~~~~~~~~
+
+MV-Delta
+- Bt848A
+- 4 Composite inputs, 1 S-VHS input (shared with 4th composite)
+- EEPROM
+
+http://www.matrix-vision.de/
+
+This card has no tuner but supports all 4 composite (1 shared with an
+S-VHS input) of the Bt848A.
+Very nice card if you only have satellite TV but several tuners connected
+to the card via composite.
+
+Many thanks to Matrix-Vision for giving us 2 cards for free which made
+Bt848a/Bt849 single crystal operation support possible!!!
+
+
+
+Miro/Pinnacle PCTV
+~~~~~~~~~~~~~~~~~~
+
+- Bt848
+ some (all??) come with 2 crystals for PAL/SECAM and NTSC
+- PAL, SECAM or NTSC TV tuner (Philips or TEMIC)
+- MSP34xx sound decoder on add on board
+ decoder is supported but AFAIK does not yet work
+ (other sound MUX setting in GPIO port needed??? somebody who fixed this???)
+- 1 tuner, 1 composite and 1 S-VHS input
+- tuner type is autodetected
+
+http://www.miro.de/
+http://www.miro.com/
+
+
+Many thanks for the free card which made first NTSC support possible back
+in 1997!
+
+
+Hauppauge Win/TV pci
+~~~~~~~~~~~~~~~~~~~~
+
+There are many different versions of the Hauppauge cards with different
+tuners (TV+Radio ...), teletext decoders.
+Note that even cards with same model numbers have (depending on the revision)
+different chips on it.
+
+- Bt848 (and others but always in 2 crystal operation???)
+ newer cards have a Bt878
+
+- PAL, SECAM, NTSC or tuner with or without Radio support
+
+e.g.:
+
+- PAL:
+
+ - TDA5737: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners
+ - TSA5522: 1.4 GHz I2C-bus controlled synthesizer, I2C 0xc2-0xc3
+
+- NTSC:
+
+ - TDA5731: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners
+ - TSA5518: no datasheet available on Philips site
+
+- Philips SAA5246 or SAA5284 ( or no) Teletext decoder chip
+ with buffer RAM (e.g. Winbond W24257AS-35: 32Kx8 CMOS static RAM)
+ SAA5246 (I2C 0x22) is supported
+
+- 256 bytes EEPROM: Microchip 24LC02B or Philips 8582E2Y
+ with configuration information
+ I2C address 0xa0 (24LC02B also responds to 0xa2-0xaf)
+
+- 1 tuner, 1 composite and (depending on model) 1 S-VHS input
+
+- 14052B: mux for selection of sound source
+
+- sound decoder: TDA9800, MSP34xx (stereo cards)
+
+
+Askey CPH-Series
+~~~~~~~~~~~~~~~~
+Developed by TelSignal(?), OEMed by many vendors (Typhoon, Anubis, Dynalink)
+
+- Card series:
+ - CPH01x: BT848 capture only
+ - CPH03x: BT848
+ - CPH05x: BT878 with FM
+ - CPH06x: BT878 (w/o FM)
+ - CPH07x: BT878 capture only
+
+- TV standards:
+ - CPH0x0: NTSC-M/M
+ - CPH0x1: PAL-B/G
+ - CPH0x2: PAL-I/I
+ - CPH0x3: PAL-D/K
+ - CPH0x4: SECAM-L/L
+ - CPH0x5: SECAM-B/G
+ - CPH0x6: SECAM-D/K
+ - CPH0x7: PAL-N/N
+ - CPH0x8: PAL-B/H
+ - CPH0x9: PAL-M/M
+
+- CPH03x was often sold as "TV capturer".
+
+Identifying:
+
+ #) 878 cards can be identified by PCI Subsystem-ID:
+ - 144f:3000 = CPH06x
+ - 144F:3002 = CPH05x w/ FM
+ - 144F:3005 = CPH06x_LC (w/o remote control)
+ #) The cards have a sticker with "CPH"-model on the back.
+ #) These cards have a number printed on the PCB just above the tuner metal box:
+ - "80-CP2000300-x" = CPH03X
+ - "80-CP2000500-x" = CPH05X
+ - "80-CP2000600-x" = CPH06X / CPH06x_LC
+
+ Askey sells these cards as "Magic TView series", Brand "MagicXpress".
+ Other OEM often call these "Tview", "TView99" or else.
+
+Lifeview Flyvideo Series:
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+The naming of these series differs in time and space.
+
+Identifying:
+ #) Some models can be identified by PCI subsystem ID:
+
+ - 1852:1852 = Flyvideo 98 FM
+ - 1851:1850 = Flyvideo 98
+ - 1851:1851 = Flyvideo 98 EZ (capture only)
+
+ #) There is a print on the PCB:
+
+ - LR25 = Flyvideo (Zoran ZR36120, SAA7110A)
+ - LR26 Rev.N = Flyvideo II (Bt848)
+ - LR26 Rev.O = Flyvideo II (Bt878)
+ - LR37 Rev.C = Flyvideo EZ (Capture only, ZR36120 + SAA7110)
+ - LR38 Rev.A1= Flyvideo II EZ (Bt848 capture only)
+ - LR50 Rev.Q = Flyvideo 98 (w/eeprom and PCI subsystem ID)
+ - LR50 Rev.W = Flyvideo 98 (no eeprom)
+ - LR51 Rev.E = Flyvideo 98 EZ (capture only)
+ - LR90 = Flyvideo 2000 (Bt878)
+ - LR90 Flyvideo 2000S (Bt878) w/Stereo TV (Package incl. LR91 daughterboard)
+ - LR91 = Stereo daughter card for LR90
+ - LR97 = Flyvideo DVBS
+ - LR99 Rev.E = Low profile card for OEM integration (only internal audio!) bt878
+ - LR136 = Flyvideo 2100/3100 (Low profile, SAA7130/SAA7134)
+ - LR137 = Flyvideo DV2000/DV3000 (SAA7130/SAA7134 + IEEE1394)
+ - LR138 Rev.C= Flyvideo 2000 (SAA7130)
+ - LR138 Flyvideo 3000 (SAA7134) w/Stereo TV
+ - These exist in variations w/FM and w/Remote sometimes denoted
+ by suffixes "FM" and "R".
+
+ #) You have a laptop (miniPCI card):
+ - Product = FlyTV Platinum Mini
+ - Model/Chip = LR212/saa7135
+
+ - Lifeview.com.tw states (Feb. 2002):
+ "The FlyVideo2000 and FlyVideo2000s product name have renamed to FlyVideo98."
+ Their Bt8x8 cards are listed as discontinued.
+ - Flyvideo 2000S was probably sold as Flyvideo 3000 in some contries(Europe?).
+ The new Flyvideo 2000/3000 are SAA7130/SAA7134 based.
+
+"Flyvideo II" had been the name for the 848 cards, nowadays (in Germany)
+this name is re-used for LR50 Rev.W.
+
+The Lifeview website mentioned Flyvideo III at some time, but such a card
+has not yet been seen (perhaps it was the german name for LR90 [stereo]).
+These cards are sold by many OEMs too.
+
+FlyVideo A2 (Elta 8680)= LR90 Rev.F (w/Remote, w/o FM, stereo TV by tda9821) {Germany}
+
+Lifeview 3000 (Elta 8681) as sold by Plus(April 2002), Germany = LR138 w/ saa7134
+
+
+Typhoon TV card series:
+~~~~~~~~~~~~~~~~~~~~~~~
+
+These can be CPH, Flyvideo, Pixelview or KNC1 series.
+Typhoon is the brand of Anubis.
+Model 50680 got re-used, some model no. had different contents over time.
+
+Models:
+
+ - 50680 "TV Tuner PCI Pal BG"(old,red package)=can be CPH03x(bt848) or CPH06x(bt878)
+ - 50680 "TV Tuner Pal BG" (blue package)= Pixelview PV-BT878P+ (Rev 9B)
+ - 50681 "TV Tuner PCI Pal I" (variant of 50680)
+ - 50682 "TView TV/FM Tuner Pal BG" = Flyvideo 98FM (LR50 Rev.Q)
+
+ .. note::
+
+ The package has a picture of CPH05x (which would be a real TView)
+
+ - 50683 "TV Tuner PCI SECAM" (variant of 50680)
+ - 50684 "TV Tuner Pal BG" = Pixelview 878TV(Rev.3D)
+ - 50686 "TV Tuner" = KNC1 TV Station
+ - 50687 "TV Tuner stereo" = KNC1 TV Station pro
+ - 50688 "TV Tuner RDS" (black package) = KNC1 TV Station RDS
+ - 50689 TV SAT DVB-S CARD CI PCI (SAA7146AH, SU1278?) = "KNC1 TV Station DVB-S"
+ - 50692 "TV/FM Tuner" (small PCB)
+ - 50694 TV TUNER CARD RDS (PHILIPS CHIPSET SAA7134HL)
+ - 50696 TV TUNER STEREO (PHILIPS CHIPSET SAA7134HL, MK3ME Tuner)
+ - 50804 PC-SAT TV/Audio Karte = Techni-PC-Sat (ZORAN 36120PQC, Tuner:Alps)
+ - 50866 TVIEW SAT RECEIVER+ADR
+ - 50868 "TV/FM Tuner Pal I" (variant of 50682)
+ - 50999 "TV/FM Tuner Secam" (variant of 50682)
+
+Guillemot
+~~~~~~~~~
+
+Models:
+
+- Maxi-TV PCI (ZR36120)
+- Maxi TV Video 2 = LR50 Rev.Q (FI1216MF, PAL BG+SECAM)
+- Maxi TV Video 3 = CPH064 (PAL BG + SECAM)
+
+Mentor
+~~~~~~
+
+Mentor TV card ("55-878TV-U1") = Pixelview 878TV(Rev.3F) (w/FM w/Remote)
+
+Prolink
+~~~~~~~
+
+- TV cards:
+
+ - PixelView Play TV pro - (Model: PV-BT878P+ REV 8E)
+ - PixelView Play TV pro - (Model: PV-BT878P+ REV 9D)
+ - PixelView Play TV pro - (Model: PV-BT878P+ REV 4C / 8D / 10A )
+ - PixelView Play TV - (Model: PV-BT848P+)
+ - 878TV - (Model: PV-BT878TV)
+
+- Multimedia TV packages (card + software pack):
+
+ - PixelView Play TV Theater - (Model: PV-M4200) = PixelView Play TV pro + Software
+ - PixelView Play TV PAK - (Model: PV-BT878P+ REV 4E)
+ - PixelView Play TV/VCR - (Model: PV-M3200 REV 4C / 8D / 10A )
+ - PixelView Studio PAK - (Model: M2200 REV 4C / 8D / 10A )
+ - PixelView PowerStudio PAK - (Model: PV-M3600 REV 4E)
+ - PixelView DigitalVCR PAK - (Model: PV-M2400 REV 4C / 8D / 10A )
+ - PixelView PlayTV PAK II (TV/FM card + usb camera) PV-M3800
+ - PixelView PlayTV XP PV-M4700,PV-M4700(w/FM)
+ - PixelView PlayTV DVR PV-M4600 package contents:PixelView PlayTV pro, windvr & videoMail s/w
+
+- Further Cards:
+
+ - PV-BT878P+rev.9B (Play TV Pro, opt. w/FM w/NICAM)
+ - PV-BT878P+rev.2F
+ - PV-BT878P Rev.1D (bt878, capture only)
+
+ - XCapture PV-CX881P (cx23881)
+ - PlayTV HD PV-CX881PL+, PV-CX881PL+(w/FM) (cx23881)
+
+ - DTV3000 PV-DTV3000P+ DVB-S CI = Twinhan VP-1030
+ - DTV2000 DVB-S = Twinhan VP-1020
+
+- Video Conferencing:
+
+ - PixelView Meeting PAK - (Model: PV-BT878P)
+ - PixelView Meeting PAK Lite - (Model: PV-BT878P)
+ - PixelView Meeting PAK plus - (Model: PV-BT878P+rev 4C/8D/10A)
+ - PixelView Capture - (Model: PV-BT848P)
+ - PixelView PlayTV USB pro
+ - Model No. PV-NT1004+, PV-NT1004+ (w/FM) = NT1004 USB decoder chip + SAA7113 video decoder chip
+
+Dynalink
+~~~~~~~~
+
+These are CPH series.
+
+Phoebemicro
+~~~~~~~~~~~
+
+- TV Master = CPH030 or CPH060
+- TV Master FM = CPH050
+
+Genius/Kye
+~~~~~~~~~~
+
+- Video Wonder/Genius Internet Video Kit = LR37 Rev.C
+- Video Wonder Pro II (848 or 878) = LR26
+
+Tekram
+~~~~~~
+
+- VideoCap C205 (Bt848)
+- VideoCap C210 (zr36120 +Philips)
+- CaptureTV M200 (ISA)
+- CaptureTV M205 (Bt848)
+
+Lucky Star
+~~~~~~~~~~
+
+- Image World Conference TV = LR50 Rev. Q
+
+Leadtek
+~~~~~~~
+
+- WinView 601 (Bt848)
+- WinView 610 (Zoran)
+- WinFast2000
+- WinFast2000 XP
+
+Support for the Leadtek WinView 601 TV/FM
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+Author of this section: Jon Tombs <jon@gte.esi.us.es>
+
+This card is basically the same as all the rest (Bt484A, Philips tuner),
+the main difference is that they have attached a programmable attenuator to 3
+GPIO lines in order to give some volume control. They have also stuck an
+infra-red remote control decoded on the board, I will add support for this
+when I get time (it simple generates an interrupt for each key press, with
+the key code is placed in the GPIO port).
+
+I don't yet have any application to test the radio support. The tuner
+frequency setting should work but it is possible that the audio multiplexer
+is wrong. If it doesn't work, send me email.
+
+
+- No Thanks to Leadtek they refused to answer any questions about their
+hardware. The driver was written by visual inspection of the card. If you
+use this driver, send an email insult to them, and tell them you won't
+continue buying their hardware unless they support Linux.
+
+- Little thanks to Princeton Technology Corp (http://www.princeton.com.tw)
+who make the audio attenuator. Their publicly available data-sheet available
+on their web site doesn't include the chip programming information! Hidden
+on their server are the full data-sheets, but don't ask how I found it.
+
+To use the driver I use the following options, the tuner and pll settings might
+be different in your country
+
+insmod videodev
+insmod i2c scan=1 i2c_debug=0 verbose=0
+insmod tuner type=1 debug=0
+insmod bttv pll=1 radio=1 card=17
+
+
+KNC One
+~~~~~~~
+
+- TV-Station
+- TV-Station SE (+Software Bundle)
+- TV-Station pro (+TV stereo)
+- TV-Station FM (+Radio)
+- TV-Station RDS (+RDS)
+- TV Station SAT (analog satellite)
+- TV-Station DVB-S
+
+.. note:: newer Cards have saa7134, but model name stayed the same?
+
+Provideo
+~~~~~~~~
+
+- PV951 or PV-951 (also are sold as:
+ Boeder TV-FM Video Capture Card,
+ Titanmedia Supervision TV-2400,
+ Provideo PV951 TF,
+ 3DeMon PV951,
+ MediaForte TV-Vision PV951,
+ Yoko PV951,
+ Vivanco Tuner Card PCI Art.-Nr.: 68404,
+ ) now named PV-951T
+
+- Surveillance Series:
+
+ - PV-141
+ - PV-143
+ - PV-147
+ - PV-148 (capture only)
+ - PV-150
+ - PV-151
+
+- TV-FM Tuner Series:
+
+ - PV-951TDV (tv tuner + 1394)
+ - PV-951T/TF
+ - PV-951PT/TF
+ - PV-956T/TF Low Profile
+ - PV-911
+
+Highscreen
+~~~~~~~~~~
+
+Models:
+
+- TV Karte = LR50 Rev.S
+- TV-Boostar = Terratec Terra TV+ Version 1.0 (Bt848, tda9821) "ceb105.pcb"
+
+Zoltrix
+~~~~~~~
+
+Models:
+
+- Face to Face Capture (Bt848 capture only) (PCB "VP-2848")
+- Face To Face TV MAX (Bt848) (PCB "VP-8482 Rev1.3")
+- Genie TV (Bt878) (PCB "VP-8790 Rev 2.1")
+- Genie Wonder Pro
+
+AVerMedia
+~~~~~~~~~
+
+- AVer FunTV Lite (ISA, AV3001 chipset) "M101.C"
+- AVerTV
+- AVerTV Stereo
+- AVerTV Studio (w/FM)
+- AVerMedia TV98 with Remote
+- AVerMedia TV/FM98 Stereo
+- AVerMedia TVCAM98
+- TVCapture (Bt848)
+- TVPhone (Bt848)
+- TVCapture98 (="AVerMedia TV98" in USA) (Bt878)
+- TVPhone98 (Bt878, w/FM)
+
+======== =========== =============== ======= ====== ======== =======================
+PCB PCI-ID Model-Name Eeprom Tuner Sound Country
+======== =========== =============== ======= ====== ======== =======================
+M101.C ISA !
+M108-B Bt848 -- FR1236 US [#f2]_,[#f3]_
+M1A8-A Bt848 AVer TV-Phone FM1216 --
+M168-T 1461:0003 AVerTV Studio 48:17 FM1216 TDA9840T D [#f1]_ w/FM w/Remote
+M168-U 1461:0004 TVCapture98 40:11 FI1216 -- D w/Remote
+M168II-B 1461:0003 Medion MD9592 48:16 FM1216 TDA9873H D w/FM
+======== =========== =============== ======= ====== ======== =======================
+
+.. [#f1] Daughterboard MB68-A with TDA9820T and TDA9840T
+.. [#f2] Sony NE41S soldered (stereo sound?)
+.. [#f3] Daughterboard M118-A w/ pic 16c54 and 4 MHz quartz
+
+- US site has different drivers for (as of 09/2002):
+
+ - EZ Capture/InterCam PCI (BT-848 chip)
+ - EZ Capture/InterCam PCI (BT-878 chip)
+ - TV-Phone (BT-848 chip)
+ - TV98 (BT-848 chip)
+ - TV98 With Remote (BT-848 chip)
+ - TV98 (BT-878 chip)
+ - TV98 With Remote (BT-878)
+ - TV/FM98 (BT-878 chip)
+ - AVerTV
+ - AverTV Stereo
+ - AVerTV Studio
+
+DE hat diverse Treiber fuer diese Modelle (Stand 09/2002):
+
+ - TVPhone (848) mit Philips tuner FR12X6 (w/ FM radio)
+ - TVPhone (848) mit Philips tuner FM12X6 (w/ FM radio)
+ - TVCapture (848) w/Philips tuner FI12X6
+ - TVCapture (848) non-Philips tuner
+ - TVCapture98 (Bt878)
+ - TVPhone98 (Bt878)
+ - AVerTV und TVCapture98 w/VCR (Bt 878)
+ - AVerTVStudio und TVPhone98 w/VCR (Bt878)
+ - AVerTV GO Serie (Kein SVideo Input)
+ - AVerTV98 (BT-878 chip)
+ - AVerTV98 mit Fernbedienung (BT-878 chip)
+ - AVerTV/FM98 (BT-878 chip)
+
+ - VDOmate (www.averm.com.cn) = M168U ?
+
+Aimslab
+~~~~~~~
+
+Models:
+
+- Video Highway or "Video Highway TR200" (ISA)
+- Video Highway Xtreme (aka "VHX") (Bt848, FM w/ TEA5757)
+
+IXMicro (former: IMS=Integrated Micro Solutions)
+~~~~~~~
+
+Models:
+
+- IXTV BT848 (=TurboTV)
+- IXTV BT878
+- IMS TurboTV (Bt848)
+
+Lifetec/Medion/Tevion/Aldi
+~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- LT9306/MD9306 = CPH061
+- LT9415/MD9415 = LR90 Rev.F or Rev.G
+- MD9592 = Avermedia TVphone98 (PCI_ID=1461:0003), PCB-Rev=M168II-B (w/TDA9873H)
+- MD9717 = KNC One (Rev D4, saa7134, FM1216 MK2 tuner)
+- MD5044 = KNC One (Rev D4, saa7134, FM1216ME MK3 tuner)
+
+Modular Technologies (www.modulartech.com) UK
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- MM100 PCTV (Bt848)
+- MM201 PCTV (Bt878, Bt832) w/ Quartzsight camera
+- MM202 PCTV (Bt878, Bt832, tda9874)
+- MM205 PCTV (Bt878)
+- MM210 PCTV (Bt878) (Galaxy TV, Galaxymedia ?)
+
+Terratec
+~~~~~~~~
+
+Models:
+
+- Terra TV+ Version 1.0 (Bt848), "ceb105.PCB" printed on the PCB, TDA9821
+- Terra TV+ Version 1.1 (Bt878), "LR74 Rev.E" printed on the PCB, TDA9821
+- Terra TValueRadio, "LR102 Rev.C" printed on the PCB
+- Terra TV/Radio+ Version 1.0, "80-CP2830100-0" TTTV3 printed on the PCB,
+ "CPH010-E83" on the back, SAA6588T, TDA9873H
+- Terra TValue Version BT878, "80-CP2830110-0 TTTV4" printed on the PCB,
+ "CPH011-D83" on back
+- Terra TValue Version 1.0 "ceb105.PCB" (really identical to Terra TV+ Version 1.0)
+- Terra TValue New Revision "LR102 Rec.C"
+- Terra Active Radio Upgrade (tea5757h, saa6588t)
+
+- LR74 is a newer PCB revision of ceb105 (both incl. connector for Active Radio Upgrade)
+
+- Cinergy 400 (saa7134), "E877 11(S)", "PM820092D" printed on PCB
+- Cinergy 600 (saa7134)
+
+Technisat
+~~~~~~~~~
+
+Models:
+
+- Discos ADR PC-Karte ISA (no TV!)
+- Discos ADR PC-Karte PCI (probably no TV?)
+- Techni-PC-Sat (Sat. analog)
+ Rev 1.2 (zr36120, vpx3220, stv0030, saa5246, BSJE3-494A)
+- Mediafocus I (zr36120/zr36125, drp3510, Sat. analog + ADR Radio)
+- Mediafocus II (saa7146, Sat. analog)
+- SatADR Rev 2.1 (saa7146a, saa7113h, stv0056a, msp3400c, drp3510a, BSKE3-307A)
+- SkyStar 1 DVB (AV7110) = Technotrend Premium
+- SkyStar 2 DVB (B2C2) (=Sky2PC)
+
+Siemens
+~~~~~~~
+
+Multimedia eXtension Board (MXB) (SAA7146, SAA7111)
+
+Powercolor
+~~~~~~~~~~
+
+Models:
+
+- MTV878
+ Package comes with different contents:
+ a) pcb "MTV878" (CARD=75)
+ b) Pixelview Rev. 4_
+- MTV878R w/Remote Control
+- MTV878F w/Remote Control w/FM radio
+
+Pinnacle
+~~~~~~~~
+
+PCTV models:
+
+- Mirovideo PCTV (Bt848)
+- Mirovideo PCTV SE (Bt848)
+- Mirovideo PCTV Pro (Bt848 + Daughterboard for TV Stereo and FM)
+- Studio PCTV Rave (Bt848 Version = Mirovideo PCTV)
+- Studio PCTV Rave (Bt878 package w/o infrared)
+- Studio PCTV (Bt878)
+- Studio PCTV Pro (Bt878 stereo w/ FM)
+- Pinnacle PCTV (Bt878, MT2032)
+- Pinnacle PCTV Pro (Bt878, MT2032)
+- Pinncale PCTV Sat (bt878a, HM1821/1221) ["Conexant CX24110 with CX24108 tuner, aka HM1221/HM1811"]
+- Pinnacle PCTV Sat XE
+
+M(J)PEG capture and playback models:
+
+- DC1+ (ISA)
+- DC10 (zr36057, zr36060, saa7110, adv7176)
+- DC10+ (zr36067, zr36060, saa7110, adv7176)
+- DC20 (ql16x24b,zr36050, zr36016, saa7110, saa7187 ...)
+- DC30 (zr36057, zr36050, zr36016, vpx3220, adv7176, ad1843, tea6415, miro FST97A1)
+- DC30+ (zr36067, zr36050, zr36016, vpx3220, adv7176)
+- DC50 (zr36067, zr36050, zr36016, saa7112, adv7176 (2 pcs.?), ad1843, miro FST97A1, Lattice ???)
+
+Lenco
+~~~~~
+
+Models:
+
+- MXR-9565 (=Technisat Mediafocus?)
+- MXR-9571 (Bt848) (=CPH031?)
+- MXR-9575
+- MXR-9577 (Bt878) (=Prolink 878TV Rev.3x)
+- MXTV-9578CP (Bt878) (= Prolink PV-BT878P+4E)
+
+Iomega
+~~~~~~
+
+Buz (zr36067, zr36060, saa7111, saa7185)
+
+LML
+~~~
+ LML33 (zr36067, zr36060, bt819, bt856)
+
+Grandtec
+~~~~~~~~
+
+Models:
+
+- Grand Video Capture (Bt848)
+- Multi Capture Card (Bt878)
+
+Koutech
+~~~~~~~
+
+Models:
+
+- KW-606 (Bt848)
+- KW-607 (Bt848 capture only)
+- KW-606RSF
+- KW-607A (capture only)
+- KW-608 (Zoran capture only)
+
+IODATA (jp)
+~~~~~~~~~~~
+
+Models:
+
+- GV-BCTV/PCI
+- GV-BCTV2/PCI
+- GV-BCTV3/PCI
+- GV-BCTV4/PCI
+- GV-VCP/PCI (capture only)
+- GV-VCP2/PCI (capture only)
+
+Canopus (jp)
+~~~~~~~~~~~~
+
+WinDVR = Kworld "KW-TVL878RF"
+
+www.sigmacom.co.kr
+~~~~~~~~~~~~~~~~~~
+
+Sigma Cyber TV II
+
+www.sasem.co.kr
+~~~~~~~~~~~~~~~
+
+Litte OnAir TV
+
+hama
+~~~~
+
+TV/Radio-Tuner Card, PCI (Model 44677) = CPH051
+
+Sigma Designs
+~~~~~~~~~~~~~
+
+Hollywood plus (em8300, em9010, adv7175), (PCB "M340-10") MPEG DVD decoder
+
+Formac
+~~~~~~
+
+Models:
+
+- iProTV (Card for iMac Mezzanine slot, Bt848+SCSI)
+- ProTV (Bt848)
+- ProTV II = ProTV Stereo (Bt878) ["stereo" means FM stereo, tv is still mono]
+
+ATI
+~~~
+
+Models:
+
+- TV-Wonder
+- TV-Wonder VE
+
+Diamond Multimedia
+~~~~~~~~~~~~~~~~~~
+
+DTV2000 (Bt848, tda9875)
+
+Aopen
+~~~~~
+
+- VA1000 Plus (w/ Stereo)
+- VA1000 Lite
+- VA1000 (=LR90)
+
+Intel
+~~~~~
+
+Models:
+
+- Smart Video Recorder (ISA full-length)
+- Smart Video Recorder pro (ISA half-length)
+- Smart Video Recorder III (Bt848)
+
+STB
+~~~
+
+Models:
+
+- STB Gateway 6000704 (bt878)
+- STB Gateway 6000699 (bt848)
+- STB Gateway 6000402 (bt848)
+- STB TV130 PCI
+
+Videologic
+~~~~~~~~~~
+
+Models:
+
+- Captivator Pro/TV (ISA?)
+- Captivator PCI/VC (Bt848 bundled with camera) (capture only)
+
+Technotrend
+~~~~~~~~~~~~
+
+Models:
+
+- TT-SAT PCI (PCB "Sat-PCI Rev.:1.3.1"; zr36125, vpx3225d, stc0056a, Tuner:BSKE6-155A
+- TT-DVB-Sat
+ - revisions 1.1, 1.3, 1.5, 1.6 and 2.1
+ - This card is sold as OEM from:
+ - Siemens DVB-s Card
+ - Hauppauge WinTV DVB-S
+ - Technisat SkyStar 1 DVB
+ - Galaxis DVB Sat
+ - Now this card is called TT-PCline Premium Family
+ - TT-Budget (saa7146, bsru6-701a)
+ This card is sold as OEM from:
+ - Hauppauge WinTV Nova
+ - Satelco Standard PCI (DVB-S)
+ - TT-DVB-C PCI
+
+Teles
+~~~~~
+
+ DVB-s (Rev. 2.2, BSRV2-301A, data only?)
+
+Remote Vision
+~~~~~~~~~~~~~
+
+MX RV605 (Bt848 capture only)
+
+Boeder
+~~~~~~
+
+Models:
+
+- PC ChatCam (Model 68252) (Bt848 capture only)
+- Tv/Fm Capture Card (Model 68404) = PV951
+
+Media-Surfer (esc-kathrein.de)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- Sat-Surfer (ISA)
+- Sat-Surfer PCI = Techni-PC-Sat
+- Cable-Surfer 1
+- Cable-Surfer 2
+- Cable-Surfer PCI (zr36120)
+- Audio-Surfer (ISA Radio card)
+
+Jetway (www.jetway.com.tw)
+~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- JW-TV 878M
+- JW-TV 878 = KWorld KW-TV878RF
+
+Galaxis
+~~~~~~~
+
+Models:
+
+- Galaxis DVB Card S CI
+- Galaxis DVB Card C CI
+- Galaxis DVB Card S
+- Galaxis DVB Card C
+- Galaxis plug.in S [neuer Name: Galaxis DVB Card S CI
+
+Hauppauge
+~~~~~~~~~
+
+Models:
+
+- many many WinTV models ...
+- WinTV DVBs = Technotrend Premium 1.3
+- WinTV NOVA = Technotrend Budget 1.1 "S-DVB DATA"
+- WinTV NOVA-CI "SDVBACI"
+- WinTV Nova USB (=Technotrend USB 1.0)
+- WinTV-Nexus-s (=Technotrend Premium 2.1 or 2.2)
+- WinTV PVR
+- WinTV PVR 250
+- WinTV PVR 450
+
+US models
+
+-990 WinTV-PVR-350 (249USD) (iTVC15 chipset + radio)
+-980 WinTV-PVR-250 (149USD) (iTVC15 chipset)
+-880 WinTV-PVR-PCI (199USD) (KFIR chipset + bt878)
+-881 WinTV-PVR-USB
+-190 WinTV-GO
+-191 WinTV-GO-FM
+-404 WinTV
+-401 WinTV-radio
+-495 WinTV-Theater
+-602 WinTV-USB
+-621 WinTV-USB-FM
+-600 USB-Live
+-698 WinTV-HD
+-697 WinTV-D
+-564 WinTV-Nexus-S
+
+Deutsche Modelle:
+
+-603 WinTV GO
+-719 WinTV Primio-FM
+-718 WinTV PCI-FM
+-497 WinTV Theater
+-569 WinTV USB
+-568 WinTV USB-FM
+-882 WinTV PVR
+-981 WinTV PVR 250
+-891 WinTV-PVR-USB
+-541 WinTV Nova
+-488 WinTV Nova-Ci
+-564 WinTV-Nexus-s
+-727 WinTV-DVB-c
+-545 Common Interface
+-898 WinTV-Nova-USB
+
+UK models:
+
+-607 WinTV Go
+-693,793 WinTV Primio FM
+-647,747 WinTV PCI FM
+-498 WinTV Theater
+-883 WinTV PVR
+-893 WinTV PVR USB (Duplicate entry)
+-566 WinTV USB (UK)
+-573 WinTV USB FM
+-429 Impact VCB (bt848)
+-600 USB Live (Video-In 1x Comp, 1xSVHS)
+-542 WinTV Nova
+-717 WinTV DVB-S
+-909 Nova-t PCI
+-893 Nova-t USB (Duplicate entry)
+-802 MyTV
+-804 MyView
+-809 MyVideo
+-872 MyTV2Go FM
+-546 WinTV Nova-S CI
+-543 WinTV Nova
+-907 Nova-S USB
+-908 Nova-T USB
+-717 WinTV Nexus-S
+-157 DEC3000-s Standalone + USB
+
+Spain:
+
+-685 WinTV-Go
+-690 WinTV-PrimioFM
+-416 WinTV-PCI Nicam Estereo
+-677 WinTV-PCI-FM
+-699 WinTV-Theater
+-683 WinTV-USB
+-678 WinTV-USB-FM
+-983 WinTV-PVR-250
+-883 WinTV-PVR-PCI
+-993 WinTV-PVR-350
+-893 WinTV-PVR-USB
+-728 WinTV-DVB-C PCI
+-832 MyTV2Go
+-869 MyTV2Go-FM
+-805 MyVideo (USB)
+
+
+Matrix-Vision
+~~~~~~~~~~~~~
+
+Models:
+
+- MATRIX-Vision MV-Delta
+- MATRIX-Vision MV-Delta 2
+- MVsigma-SLC (Bt848)
+
+Conceptronic (.net)
+~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- TVCON FM, TV card w/ FM = CPH05x
+- TVCON = CPH06x
+
+BestData
+~~~~~~~~
+
+Models:
+
+- HCC100 = VCC100rev1 + camera
+- VCC100 rev1 (bt848)
+- VCC100 rev2 (bt878)
+
+Gallant (www.gallantcom.com) www.minton.com.tw
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- Intervision IV-510 (capture only bt8x8)
+- Intervision IV-550 (bt8x8)
+- Intervision IV-100 (zoran)
+- Intervision IV-1000 (bt8x8)
+
+Asonic (www.asonic.com.cn) (website down)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+SkyEye tv 878
+
+Hoontech
+~~~~~~~~
+
+878TV/FM
+
+Teppro (www.itcteppro.com.tw)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- ITC PCITV (Card Ver 1.0) "Teppro TV1/TVFM1 Card"
+- ITC PCITV (Card Ver 2.0)
+- ITC PCITV (Card Ver 3.0) = "PV-BT878P+ (REV.9D)"
+- ITC PCITV (Card Ver 4.0)
+- TEPPRO IV-550 (For BT848 Main Chip)
+- ITC DSTTV (bt878, satellite)
+- ITC VideoMaker (saa7146, StreamMachine sm2110, tvtuner) "PV-SM2210P+ (REV:1C)"
+
+Kworld (www.kworld.com.tw)
+~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+PC TV Station:
+
+- KWORLD KW-TV878R TV (no radio)
+- KWORLD KW-TV878RF TV (w/ radio)
+- KWORLD KW-TVL878RF (low profile)
+- KWORLD KW-TV713XRF (saa7134)
+
+
+ MPEG TV Station (same cards as above plus WinDVR Software MPEG en/decoder)
+
+- KWORLD KW-TV878R -Pro TV (no Radio)
+- KWORLD KW-TV878RF-Pro TV (w/ Radio)
+- KWORLD KW-TV878R -Ultra TV (no Radio)
+- KWORLD KW-TV878RF-Ultra TV (w/ Radio)
+
+JTT/ Justy Corp.(http://www.jtt.ne.jp/)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+JTT-02 (JTT TV) "TV watchmate pro" (bt848)
+
+ADS www.adstech.com
+~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- Channel Surfer TV ( CHX-950 )
+- Channel Surfer TV+FM ( CHX-960FM )
+
+AVEC www.prochips.com
+~~~~~~~~~~~~~~~~~~~~~
+
+AVEC Intercapture (bt848, tea6320)
+
+NoBrand
+~~~~~~~
+
+TV Excel = Australian Name for "PV-BT878P+ 8E" or "878TV Rev.3_"
+
+Mach www.machspeed.com
+~~~~~~~~~~~~~~~~~~~~~~
+
+Mach TV 878
+
+Eline www.eline-net.com/
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- Eline Vision TVMaster / TVMaster FM (ELV-TVM/ ELV-TVM-FM) = LR26 (bt878)
+- Eline Vision TVMaster-2000 (ELV-TVM-2000, ELV-TVM-2000-FM)= LR138 (saa713x)
+
+Spirit
+~~~~~~
+
+- Spirit TV Tuner/Video Capture Card (bt848)
+
+Boser www.boser.com.tw
+~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- HS-878 Mini PCI Capture Add-on Card
+- HS-879 Mini PCI 3D Audio and Capture Add-on Card (w/ ES1938 Solo-1)
+
+Satelco www.citycom-gmbh.de, www.satelco.de
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- TV-FM =KNC1 saa7134
+- Standard PCI (DVB-S) = Technotrend Budget
+- Standard PCI (DVB-S) w/ CI
+- Satelco Highend PCI (DVB-S) = Technotrend Premium
+
+
+Sensoray www.sensoray.com
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- Sensoray 311 (PC/104 bus)
+- Sensoray 611 (PCI)
+
+CEI (Chartered Electronics Industries Pte Ltd [CEI] [FCC ID HBY])
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- TV Tuner - HBY-33A-RAFFLES Brooktree Bt848KPF + Philips
+- TV Tuner MG9910 - HBY33A-TVO CEI + Philips SAA7110 + OKI M548262 + ST STV8438CV
+- Primetime TV (ISA)
+ - acquired by Singapore Technologies
+ - now operating as Chartered Semiconductor Manufacturing
+ - Manufacturer of video cards is listed as:
+ - Cogent Electronics Industries [CEI]
+
+AITech
+~~~~~~
+
+Models:
+
+- Wavewatcher TV (ISA)
+- AITech WaveWatcher TV-PCI = can be LR26 (Bt848) or LR50 (BT878)
+- WaveWatcher TVR-202 TV/FM Radio Card (ISA)
+
+MAXRON
+~~~~~~
+
+Maxron MaxTV/FM Radio (KW-TV878-FNT) = Kworld or JW-TV878-FBK
+
+www.ids-imaging.de
+~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- Falcon Series (capture only)
+ In USA: http://www.theimagingsource.com/
+- DFG/LC1
+
+www.sknet-web.co.jp
+~~~~~~~~~~~~~~~~~~~
+
+SKnet Monster TV (saa7134)
+
+A-Max www.amaxhk.com (Colormax, Amax, Napa)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+APAC Viewcomp 878
+
+Cybertainment
+~~~~~~~~~~~~~
+
+Models:
+
+- CyberMail AV Video Email Kit w/ PCI Capture Card (capture only)
+- CyberMail Xtreme
+
+These are Flyvideo
+
+VCR (http://www.vcrinc.com/)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Video Catcher 16
+
+Twinhan
+~~~~~~~
+
+Models:
+
+- DST Card/DST-IP (bt878, twinhan asic) VP-1020
+ - Sold as:
+ - KWorld DVBS Satellite TV-Card
+ - Powercolor DSTV Satellite Tuner Card
+ - Prolink Pixelview DTV2000
+ - Provideo PV-911 Digital Satellite TV Tuner Card With Common Interface ?
+- DST-CI Card (DVB Satellite) VP-1030
+- DCT Card (DVB cable)
+
+MSI
+~~~
+
+Models:
+
+- MSI TV@nywhere Tuner Card (MS-8876) (CX23881/883) Not Bt878 compatible.
+- MS-8401 DVB-S
+
+Focus www.focusinfo.com
+~~~~~~~~~~~~~~~~~~~~~~~
+
+InVideo PCI (bt878)
+
+Sdisilk www.sdisilk.com/
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- SDI Silk 100
+- SDI Silk 200 SDI Input Card
+
+www.euresys.com
+~~~~~~~~~~~~~~~
+
+PICOLO series
+
+PMC/Pace
+~~~~~~~~
+
+www.pacecom.co.uk website closed
+
+Mercury www.kobian.com (UK and FR)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- LR50
+- LR138RBG-Rx == LR138
+
+TEC sound
+~~~~~~~~~
+
+TV-Mate = Zoltrix VP-8482
+
+Though educated googling found: www.techmakers.com
+
+(package and manuals don't have any other manufacturer info) TecSound
+
+Lorenzen www.lorenzen.de
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+SL DVB-S PCI = Technotrend Budget PCI (su1278 or bsru version)
+
+Origo (.uk) www.origo2000.com
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+PC TV Card = LR50
+
+I/O Magic www.iomagic.com
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+PC PVR - Desktop TV Personal Video Recorder DR-PCTV100 = Pinnacle ROB2D-51009464 4.0 + Cyberlink PowerVCR II
+
+Arowana
+~~~~~~~
+
+TV-Karte / Poso Power TV (?) = Zoltrix VP-8482 (?)
+
+iTVC15 boards:
+~~~~~~~~~~~~~
+
+kuroutoshikou.com ITVC15
+yuan.com MPG160 PCI TV (Internal PCI MPEG2 encoder card plus TV-tuner)
+
+Asus www.asuscom.com
+~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- Asus TV Tuner Card 880 NTSC (low profile, cx23880)
+- Asus TV (saa7134)
+
+Hoontech
+~~~~~~~~
+
+http://www.hoontech.de/
+
+- HART Vision 848 (H-ART Vision 848)
+- HART Vision 878 (H-Art Vision 878)
+
+
+
+Chips used at bttv devices
+--------------------------
+
+- all boards:
+
+ - Brooktree Bt848/848A/849/878/879: video capture chip
+
+- Board specific
+
+ - Miro PCTV:
+
+ - Philips or Temic Tuner
+
+ - Hauppauge Win/TV pci (version 405):
+
+ - Microchip 24LC02B or Philips 8582E2Y:
+ - 256 Byte EEPROM with configuration information
+ - I2C 0xa0-0xa1, (24LC02B also responds to 0xa2-0xaf)
+ - Philips SAA5246AGP/E: Videotext decoder chip, I2C 0x22-0x23
+
+ - TDA9800: sound decoder
+
+ - Winbond W24257AS-35: 32Kx8 CMOS static RAM (Videotext buffer mem)
+
+ - 14052B: analog switch for selection of sound source
+
+- PAL:
+
+ - TDA5737: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners
+ - TSA5522: 1.4 GHz I2C-bus controlled synthesizer, I2C 0xc2-0xc3
+
+- NTSC:
+
+ - TDA5731: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners
+ - TSA5518: no datasheet available on Philips site
+
+- STB TV pci:
+
+ - ???
+ - if you want better support for STB cards send me info!
+ Look at the board! What chips are on it?
+
+
+
+
+Specs
+-----
+Philips http://www.Semiconductors.COM/pip/
+Conexant http://www.conexant.com/
+Micronas http://www.micronas.com/en/home/index.html
+
+Thanks
+------
+
+Many thanks to:
+
+- Markus Schroeder <schroedm@uni-duesseldorf.de> for information on the Bt848
+ and tuner programming and his control program xtvc.
+
+- Martin Buck <martin-2.buck@student.uni-ulm.de> for his great Videotext
+ package.
+
+- Gerd Hoffmann for the MSP3400 support and the modular
+ I2C, tuner, ... support.
+
+
+- MATRIX Vision for giving us 2 cards for free, which made support of
+ single crystal operation possible.
+
+- MIRO for providing a free PCTV card and detailed information about the
+ components on their cards. (E.g. how the tuner type is detected)
+ Without their card I could not have debugged the NTSC mode.
+
+- Hauppauge for telling how the sound input is selected and what components
+ they do and will use on their radio cards.
+ Also many thanks for faxing me the FM1216 data sheet.
+
+Contributors
+------------
+
+Michael Chu <mmchu@pobox.com>
+ AverMedia fix and more flexible card recognition
+
+Alan Cox <alan@lxorguk.ukuu.org.uk>
+ Video4Linux interface and 2.1.x kernel adaptation
+
+Chris Kleitsch
+ Hardware I2C
+
+Gerd Hoffmann
+ Radio card (ITT sound processor)
+
+bigfoot <bigfoot@net-way.net>
+Ragnar Hojland Espinosa <ragnar@macula.net>
+ ConferenceTV card
+
+
++ many more (please mail me if you are missing in this list and would
+ like to be mentioned)
diff --git a/Documentation/video4linux/bttv/Tuners b/Documentation/media/v4l-drivers/tuners.rst
similarity index 100%
rename from Documentation/video4linux/bttv/Tuners
rename to Documentation/media/v4l-drivers/tuners.rst
diff --git a/Documentation/video4linux/bttv/CONTRIBUTORS b/Documentation/video4linux/bttv/CONTRIBUTORS
deleted file mode 100644
index eb41b2650860..000000000000
--- a/Documentation/video4linux/bttv/CONTRIBUTORS
+++ /dev/null
@@ -1,25 +0,0 @@
-Contributors to bttv:
-
-Michael Chu <mmchu@pobox.com>
- AverMedia fix and more flexible card recognition
-
-Alan Cox <alan@lxorguk.ukuu.org.uk>
- Video4Linux interface and 2.1.x kernel adaptation
-
-Chris Kleitsch
- Hardware I2C
-
-Gerd Knorr <kraxel@cs.tu-berlin.de>
- Radio card (ITT sound processor)
-
-bigfoot <bigfoot@net-way.net>
-Ragnar Hojland Espinosa <ragnar@macula.net>
- ConferenceTV card
-
-
-+ many more (please mail me if you are missing in this list and would
- like to be mentioned)
-
-
-
-
diff --git a/Documentation/video4linux/bttv/Cards b/Documentation/video4linux/bttv/Cards
deleted file mode 100644
index a8fb6e2d3c8b..000000000000
--- a/Documentation/video4linux/bttv/Cards
+++ /dev/null
@@ -1,960 +0,0 @@
-
-Gunther Mayer's bttv card gallery (graphical version of this text file :-)
-is available at: http://www.bttv-gallery.de/
-
-
-Supported cards:
-Bt848/Bt848a/Bt849/Bt878/Bt879 cards
-------------------------------------
-
-All cards with Bt848/Bt848a/Bt849/Bt878/Bt879 and normal
-Composite/S-VHS inputs are supported. Teletext and Intercast support
-(PAL only) for ALL cards via VBI sample decoding in software.
-
-Some cards with additional multiplexing of inputs or other additional
-fancy chips are only partially supported (unless specifications by the
-card manufacturer are given). When a card is listed here it isn't
-necessarily fully supported.
-
-All other cards only differ by additional components as tuners, sound
-decoders, EEPROMs, teletext decoders ...
-
-
-Unsupported Cards:
-------------------
-
-Cards with Zoran (ZR) or Philips (SAA) or ISA are not supported by
-this driver.
-
-
-MATRIX Vision
--------------
-
-MV-Delta
-- Bt848A
-- 4 Composite inputs, 1 S-VHS input (shared with 4th composite)
-- EEPROM
-
-http://www.matrix-vision.de/
-
-This card has no tuner but supports all 4 composite (1 shared with an
-S-VHS input) of the Bt848A.
-Very nice card if you only have satellite TV but several tuners connected
-to the card via composite.
-
-Many thanks to Matrix-Vision for giving us 2 cards for free which made
-Bt848a/Bt849 single crystal operation support possible!!!
-
-
-
-Miro/Pinnacle PCTV
-------------------
-
-- Bt848
- some (all??) come with 2 crystals for PAL/SECAM and NTSC
-- PAL, SECAM or NTSC TV tuner (Philips or TEMIC)
-- MSP34xx sound decoder on add on board
- decoder is supported but AFAIK does not yet work
- (other sound MUX setting in GPIO port needed??? somebody who fixed this???)
-- 1 tuner, 1 composite and 1 S-VHS input
-- tuner type is autodetected
-
-http://www.miro.de/
-http://www.miro.com/
-
-
-Many thanks for the free card which made first NTSC support possible back
-in 1997!
-
-
-Hauppauge Win/TV pci
---------------------
-
-There are many different versions of the Hauppauge cards with different
-tuners (TV+Radio ...), teletext decoders.
-Note that even cards with same model numbers have (depending on the revision)
-different chips on it.
-
-- Bt848 (and others but always in 2 crystal operation???)
- newer cards have a Bt878
-- PAL, SECAM, NTSC or tuner with or without Radio support
-
-e.g.:
- PAL:
- TDA5737: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners
- TSA5522: 1.4 GHz I2C-bus controlled synthesizer, I2C 0xc2-0xc3
-
- NTSC:
- TDA5731: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners
- TSA5518: no datasheet available on Philips site
-- Philips SAA5246 or SAA5284 ( or no) Teletext decoder chip
- with buffer RAM (e.g. Winbond W24257AS-35: 32Kx8 CMOS static RAM)
- SAA5246 (I2C 0x22) is supported
-- 256 bytes EEPROM: Microchip 24LC02B or Philips 8582E2Y
- with configuration information
- I2C address 0xa0 (24LC02B also responds to 0xa2-0xaf)
-- 1 tuner, 1 composite and (depending on model) 1 S-VHS input
-- 14052B: mux for selection of sound source
-- sound decoder: TDA9800, MSP34xx (stereo cards)
-
-
-Askey CPH-Series
-----------------
-Developed by TelSignal(?), OEMed by many vendors (Typhoon, Anubis, Dynalink)
-
- Card series:
- CPH01x: BT848 capture only
- CPH03x: BT848
- CPH05x: BT878 with FM
- CPH06x: BT878 (w/o FM)
- CPH07x: BT878 capture only
-
- TV standards:
- CPH0x0: NTSC-M/M
- CPH0x1: PAL-B/G
- CPH0x2: PAL-I/I
- CPH0x3: PAL-D/K
- CPH0x4: SECAM-L/L
- CPH0x5: SECAM-B/G
- CPH0x6: SECAM-D/K
- CPH0x7: PAL-N/N
- CPH0x8: PAL-B/H
- CPH0x9: PAL-M/M
-
- CPH03x was often sold as "TV capturer".
-
- Identifying:
- 1) 878 cards can be identified by PCI Subsystem-ID:
- 144f:3000 = CPH06x
- 144F:3002 = CPH05x w/ FM
- 144F:3005 = CPH06x_LC (w/o remote control)
- 1) The cards have a sticker with "CPH"-model on the back.
- 2) These cards have a number printed on the PCB just above the tuner metal box:
- "80-CP2000300-x" = CPH03X
- "80-CP2000500-x" = CPH05X
- "80-CP2000600-x" = CPH06X / CPH06x_LC
-
- Askey sells these cards as "Magic TView series", Brand "MagicXpress".
- Other OEM often call these "Tview", "TView99" or else.
-
-Lifeview Flyvideo Series:
--------------------------
- The naming of these series differs in time and space.
-
- Identifying:
- 1) Some models can be identified by PCI subsystem ID:
- 1852:1852 = Flyvideo 98 FM
- 1851:1850 = Flyvideo 98
- 1851:1851 = Flyvideo 98 EZ (capture only)
- 2) There is a print on the PCB:
- LR25 = Flyvideo (Zoran ZR36120, SAA7110A)
- LR26 Rev.N = Flyvideo II (Bt848)
- Rev.O = Flyvideo II (Bt878)
- LR37 Rev.C = Flyvideo EZ (Capture only, ZR36120 + SAA7110)
- LR38 Rev.A1= Flyvideo II EZ (Bt848 capture only)
- LR50 Rev.Q = Flyvideo 98 (w/eeprom and PCI subsystem ID)
- Rev.W = Flyvideo 98 (no eeprom)
- LR51 Rev.E = Flyvideo 98 EZ (capture only)
- LR90 = Flyvideo 2000 (Bt878)
- Flyvideo 2000S (Bt878) w/Stereo TV (Package incl. LR91 daughterboard)
- LR91 = Stereo daughter card for LR90
- LR97 = Flyvideo DVBS
- LR99 Rev.E = Low profile card for OEM integration (only internal audio!) bt878
- LR136 = Flyvideo 2100/3100 (Low profile, SAA7130/SAA7134)
- LR137 = Flyvideo DV2000/DV3000 (SAA7130/SAA7134 + IEEE1394)
- LR138 Rev.C= Flyvideo 2000 (SAA7130)
- or Flyvideo 3000 (SAA7134) w/Stereo TV
- These exist in variations w/FM and w/Remote sometimes denoted
- by suffixes "FM" and "R".
- 3) You have a laptop (miniPCI card):
- Product = FlyTV Platinum Mini
- Model/Chip = LR212/saa7135
-
- Lifeview.com.tw states (Feb. 2002):
- "The FlyVideo2000 and FlyVideo2000s product name have renamed to FlyVideo98."
- Their Bt8x8 cards are listed as discontinued.
- Flyvideo 2000S was probably sold as Flyvideo 3000 in some contries(Europe?).
- The new Flyvideo 2000/3000 are SAA7130/SAA7134 based.
-
- "Flyvideo II" had been the name for the 848 cards, nowadays (in Germany)
- this name is re-used for LR50 Rev.W.
- The Lifeview website mentioned Flyvideo III at some time, but such a card
- has not yet been seen (perhaps it was the german name for LR90 [stereo]).
- These cards are sold by many OEMs too.
-
- FlyVideo A2 (Elta 8680)= LR90 Rev.F (w/Remote, w/o FM, stereo TV by tda9821) {Germany}
- Lifeview 3000 (Elta 8681) as sold by Plus(April 2002), Germany = LR138 w/ saa7134
-
-
-Typhoon TV card series:
------------------------
- These can be CPH, Flyvideo, Pixelview or KNC1 series.
- Typhoon is the brand of Anubis.
- Model 50680 got re-used, some model no. had different contents over time.
-
- Models:
- 50680 "TV Tuner PCI Pal BG"(old,red package)=can be CPH03x(bt848) or CPH06x(bt878)
- 50680 "TV Tuner Pal BG" (blue package)= Pixelview PV-BT878P+ (Rev 9B)
- 50681 "TV Tuner PCI Pal I" (variant of 50680)
- 50682 "TView TV/FM Tuner Pal BG" = Flyvideo 98FM (LR50 Rev.Q)
- Note: The package has a picture of CPH05x (which would be a real TView)
- 50683 "TV Tuner PCI SECAM" (variant of 50680)
- 50684 "TV Tuner Pal BG" = Pixelview 878TV(Rev.3D)
- 50686 "TV Tuner" = KNC1 TV Station
- 50687 "TV Tuner stereo" = KNC1 TV Station pro
- 50688 "TV Tuner RDS" (black package) = KNC1 TV Station RDS
- 50689 TV SAT DVB-S CARD CI PCI (SAA7146AH, SU1278?) = "KNC1 TV Station DVB-S"
- 50692 "TV/FM Tuner" (small PCB)
- 50694 TV TUNER CARD RDS (PHILIPS CHIPSET SAA7134HL)
- 50696 TV TUNER STEREO (PHILIPS CHIPSET SAA7134HL, MK3ME Tuner)
- 50804 PC-SAT TV/Audio Karte = Techni-PC-Sat (ZORAN 36120PQC, Tuner:Alps)
- 50866 TVIEW SAT RECEIVER+ADR
- 50868 "TV/FM Tuner Pal I" (variant of 50682)
- 50999 "TV/FM Tuner Secam" (variant of 50682)
-
-
-Guillemot
----------
- Maxi-TV PCI (ZR36120)
- Maxi TV Video 2 = LR50 Rev.Q (FI1216MF, PAL BG+SECAM)
- Maxi TV Video 3 = CPH064 (PAL BG + SECAM)
-
-Mentor
-------
- Mentor TV card ("55-878TV-U1") = Pixelview 878TV(Rev.3F) (w/FM w/Remote)
-
-Prolink
--------
- TV cards:
- PixelView Play TV pro - (Model: PV-BT878P+ REV 8E)
- PixelView Play TV pro - (Model: PV-BT878P+ REV 9D)
- PixelView Play TV pro - (Model: PV-BT878P+ REV 4C / 8D / 10A )
- PixelView Play TV - (Model: PV-BT848P+)
- 878TV - (Model: PV-BT878TV)
-
- Multimedia TV packages (card + software pack):
- PixelView Play TV Theater - (Model: PV-M4200) = PixelView Play TV pro + Software
- PixelView Play TV PAK - (Model: PV-BT878P+ REV 4E)
- PixelView Play TV/VCR - (Model: PV-M3200 REV 4C / 8D / 10A )
- PixelView Studio PAK - (Model: M2200 REV 4C / 8D / 10A )
- PixelView PowerStudio PAK - (Model: PV-M3600 REV 4E)
- PixelView DigitalVCR PAK - (Model: PV-M2400 REV 4C / 8D / 10A )
-
- PixelView PlayTV PAK II (TV/FM card + usb camera) PV-M3800
- PixelView PlayTV XP PV-M4700,PV-M4700(w/FM)
- PixelView PlayTV DVR PV-M4600 package contents:PixelView PlayTV pro, windvr & videoMail s/w
-
- Further Cards:
- PV-BT878P+rev.9B (Play TV Pro, opt. w/FM w/NICAM)
- PV-BT878P+rev.2F
- PV-BT878P Rev.1D (bt878, capture only)
-
- XCapture PV-CX881P (cx23881)
- PlayTV HD PV-CX881PL+, PV-CX881PL+(w/FM) (cx23881)
-
- DTV3000 PV-DTV3000P+ DVB-S CI = Twinhan VP-1030
- DTV2000 DVB-S = Twinhan VP-1020
-
- Video Conferencing:
- PixelView Meeting PAK - (Model: PV-BT878P)
- PixelView Meeting PAK Lite - (Model: PV-BT878P)
- PixelView Meeting PAK plus - (Model: PV-BT878P+rev 4C/8D/10A)
- PixelView Capture - (Model: PV-BT848P)
-
- PixelView PlayTV USB pro
- Model No. PV-NT1004+, PV-NT1004+ (w/FM) = NT1004 USB decoder chip + SAA7113 video decoder chip
-
-Dynalink
---------
- These are CPH series.
-
-Phoebemicro
------------
- TV Master = CPH030 or CPH060
- TV Master FM = CPH050
-
-Genius/Kye
-----------
- Video Wonder/Genius Internet Video Kit = LR37 Rev.C
- Video Wonder Pro II (848 or 878) = LR26
-
-Tekram
-------
- VideoCap C205 (Bt848)
- VideoCap C210 (zr36120 +Philips)
- CaptureTV M200 (ISA)
- CaptureTV M205 (Bt848)
-
-Lucky Star
-----------
- Image World Conference TV = LR50 Rev. Q
-
-Leadtek
--------
- WinView 601 (Bt848)
- WinView 610 (Zoran)
- WinFast2000
- WinFast2000 XP
-
-KNC One
--------
- TV-Station
- TV-Station SE (+Software Bundle)
- TV-Station pro (+TV stereo)
- TV-Station FM (+Radio)
- TV-Station RDS (+RDS)
- TV Station SAT (analog satellite)
- TV-Station DVB-S
-
- newer Cards have saa7134, but model name stayed the same?
-
-Provideo
---------
- PV951 or PV-951 (also are sold as:
- Boeder TV-FM Video Capture Card
- Titanmedia Supervision TV-2400
- Provideo PV951 TF
- 3DeMon PV951
- MediaForte TV-Vision PV951
- Yoko PV951
- Vivanco Tuner Card PCI Art.-Nr.: 68404
- ) now named PV-951T
-
- Surveillance Series
- PV-141
- PV-143
- PV-147
- PV-148 (capture only)
- PV-150
- PV-151
-
- TV-FM Tuner Series
- PV-951TDV (tv tuner + 1394)
- PV-951T/TF
- PV-951PT/TF
- PV-956T/TF Low Profile
- PV-911
-
-Highscreen
-----------
- TV Karte = LR50 Rev.S
- TV-Boostar = Terratec Terra TV+ Version 1.0 (Bt848, tda9821) "ceb105.pcb"
-
-Zoltrix
--------
- Face to Face Capture (Bt848 capture only) (PCB "VP-2848")
- Face To Face TV MAX (Bt848) (PCB "VP-8482 Rev1.3")
- Genie TV (Bt878) (PCB "VP-8790 Rev 2.1")
- Genie Wonder Pro
-
-AVerMedia
----------
- AVer FunTV Lite (ISA, AV3001 chipset) "M101.C"
- AVerTV
- AVerTV Stereo
- AVerTV Studio (w/FM)
- AVerMedia TV98 with Remote
- AVerMedia TV/FM98 Stereo
- AVerMedia TVCAM98
- TVCapture (Bt848)
- TVPhone (Bt848)
- TVCapture98 (="AVerMedia TV98" in USA) (Bt878)
- TVPhone98 (Bt878, w/FM)
-
- PCB PCI-ID Model-Name Eeprom Tuner Sound Country
- --------------------------------------------------------------------
- M101.C ISA !
- M108-B Bt848 -- FR1236 US (2),(3)
- M1A8-A Bt848 AVer TV-Phone FM1216 --
- M168-T 1461:0003 AVerTV Studio 48:17 FM1216 TDA9840T D (1) w/FM w/Remote
- M168-U 1461:0004 TVCapture98 40:11 FI1216 -- D w/Remote
- M168II-B 1461:0003 Medion MD9592 48:16 FM1216 TDA9873H D w/FM
-
- (1) Daughterboard MB68-A with TDA9820T and TDA9840T
- (2) Sony NE41S soldered (stereo sound?)
- (3) Daughterboard M118-A w/ pic 16c54 and 4 MHz quartz
-
- US site has different drivers for (as of 09/2002):
- EZ Capture/InterCam PCI (BT-848 chip)
- EZ Capture/InterCam PCI (BT-878 chip)
- TV-Phone (BT-848 chip)
- TV98 (BT-848 chip)
- TV98 With Remote (BT-848 chip)
- TV98 (BT-878 chip)
- TV98 With Remote (BT-878)
- TV/FM98 (BT-878 chip)
- AVerTV
- AverTV Stereo
- AVerTV Studio
-
- DE hat diverse Treiber fuer diese Modelle (Stand 09/2002):
- TVPhone (848) mit Philips tuner FR12X6 (w/ FM radio)
- TVPhone (848) mit Philips tuner FM12X6 (w/ FM radio)
- TVCapture (848) w/Philips tuner FI12X6
- TVCapture (848) non-Philips tuner
- TVCapture98 (Bt878)
- TVPhone98 (Bt878)
- AVerTV und TVCapture98 w/VCR (Bt 878)
- AVerTVStudio und TVPhone98 w/VCR (Bt878)
- AVerTV GO Serie (Kein SVideo Input)
- AVerTV98 (BT-878 chip)
- AVerTV98 mit Fernbedienung (BT-878 chip)
- AVerTV/FM98 (BT-878 chip)
-
- VDOmate (www.averm.com.cn) = M168U ?
-
-Aimslab
--------
- Video Highway or "Video Highway TR200" (ISA)
- Video Highway Xtreme (aka "VHX") (Bt848, FM w/ TEA5757)
-
-IXMicro (former: IMS=Integrated Micro Solutions)
--------
- IXTV BT848 (=TurboTV)
- IXTV BT878
- IMS TurboTV (Bt848)
-
-Lifetec/Medion/Tevion/Aldi
---------------------------
- LT9306/MD9306 = CPH061
- LT9415/MD9415 = LR90 Rev.F or Rev.G
- MD9592 = Avermedia TVphone98 (PCI_ID=1461:0003), PCB-Rev=M168II-B (w/TDA9873H)
- MD9717 = KNC One (Rev D4, saa7134, FM1216 MK2 tuner)
- MD5044 = KNC One (Rev D4, saa7134, FM1216ME MK3 tuner)
-
-Modular Technologies (www.modulartech.com) UK
----------------------------------------------
- MM100 PCTV (Bt848)
- MM201 PCTV (Bt878, Bt832) w/ Quartzsight camera
- MM202 PCTV (Bt878, Bt832, tda9874)
- MM205 PCTV (Bt878)
- MM210 PCTV (Bt878) (Galaxy TV, Galaxymedia ?)
-
-Terratec
---------
- Terra TV+ Version 1.0 (Bt848), "ceb105.PCB" printed on the PCB, TDA9821
- Terra TV+ Version 1.1 (Bt878), "LR74 Rev.E" printed on the PCB, TDA9821
- Terra TValueRadio, "LR102 Rev.C" printed on the PCB
- Terra TV/Radio+ Version 1.0, "80-CP2830100-0" TTTV3 printed on the PCB,
- "CPH010-E83" on the back, SAA6588T, TDA9873H
- Terra TValue Version BT878, "80-CP2830110-0 TTTV4" printed on the PCB,
- "CPH011-D83" on back
- Terra TValue Version 1.0 "ceb105.PCB" (really identical to Terra TV+ Version 1.0)
- Terra TValue New Revision "LR102 Rec.C"
- Terra Active Radio Upgrade (tea5757h, saa6588t)
-
- LR74 is a newer PCB revision of ceb105 (both incl. connector for Active Radio Upgrade)
-
- Cinergy 400 (saa7134), "E877 11(S)", "PM820092D" printed on PCB
- Cinergy 600 (saa7134)
-
-Technisat
----------
- Discos ADR PC-Karte ISA (no TV!)
- Discos ADR PC-Karte PCI (probably no TV?)
- Techni-PC-Sat (Sat. analog)
- Rev 1.2 (zr36120, vpx3220, stv0030, saa5246, BSJE3-494A)
- Mediafocus I (zr36120/zr36125, drp3510, Sat. analog + ADR Radio)
- Mediafocus II (saa7146, Sat. analog)
- SatADR Rev 2.1 (saa7146a, saa7113h, stv0056a, msp3400c, drp3510a, BSKE3-307A)
- SkyStar 1 DVB (AV7110) = Technotrend Premium
- SkyStar 2 DVB (B2C2) (=Sky2PC)
-
-Siemens
--------
- Multimedia eXtension Board (MXB) (SAA7146, SAA7111)
-
-Powercolor
-----------
- MTV878
- Package comes with different contents:
- a) pcb "MTV878" (CARD=75)
- b) Pixelview Rev. 4_
- MTV878R w/Remote Control
- MTV878F w/Remote Control w/FM radio
-
-Pinnacle
---------
- Mirovideo PCTV (Bt848)
- Mirovideo PCTV SE (Bt848)
- Mirovideo PCTV Pro (Bt848 + Daughterboard for TV Stereo and FM)
- Studio PCTV Rave (Bt848 Version = Mirovideo PCTV)
- Studio PCTV Rave (Bt878 package w/o infrared)
- Studio PCTV (Bt878)
- Studio PCTV Pro (Bt878 stereo w/ FM)
- Pinnacle PCTV (Bt878, MT2032)
- Pinnacle PCTV Pro (Bt878, MT2032)
- Pinncale PCTV Sat (bt878a, HM1821/1221) ["Conexant CX24110 with CX24108 tuner, aka HM1221/HM1811"]
- Pinnacle PCTV Sat XE
-
- M(J)PEG capture and playback:
- DC1+ (ISA)
- DC10 (zr36057, zr36060, saa7110, adv7176)
- DC10+ (zr36067, zr36060, saa7110, adv7176)
- DC20 (ql16x24b,zr36050, zr36016, saa7110, saa7187 ...)
- DC30 (zr36057, zr36050, zr36016, vpx3220, adv7176, ad1843, tea6415, miro FST97A1)
- DC30+ (zr36067, zr36050, zr36016, vpx3220, adv7176)
- DC50 (zr36067, zr36050, zr36016, saa7112, adv7176 (2 pcs.?), ad1843, miro FST97A1, Lattice ???)
-
-Lenco
------
- MXR-9565 (=Technisat Mediafocus?)
- MXR-9571 (Bt848) (=CPH031?)
- MXR-9575
- MXR-9577 (Bt878) (=Prolink 878TV Rev.3x)
- MXTV-9578CP (Bt878) (= Prolink PV-BT878P+4E)
-
-Iomega
-------
- Buz (zr36067, zr36060, saa7111, saa7185)
-
-LML
----
- LML33 (zr36067, zr36060, bt819, bt856)
-
-Grandtec
---------
- Grand Video Capture (Bt848)
- Multi Capture Card (Bt878)
-
-Koutech
--------
- KW-606 (Bt848)
- KW-607 (Bt848 capture only)
- KW-606RSF
- KW-607A (capture only)
- KW-608 (Zoran capture only)
-
-IODATA (jp)
-------
- GV-BCTV/PCI
- GV-BCTV2/PCI
- GV-BCTV3/PCI
- GV-BCTV4/PCI
- GV-VCP/PCI (capture only)
- GV-VCP2/PCI (capture only)
-
-Canopus (jp)
--------
- WinDVR = Kworld "KW-TVL878RF"
-
-www.sigmacom.co.kr
-------------------
- Sigma Cyber TV II
-
-www.sasem.co.kr
----------------
- Litte OnAir TV
-
-hama
-----
- TV/Radio-Tuner Card, PCI (Model 44677) = CPH051
-
-Sigma Designs
--------------
- Hollywood plus (em8300, em9010, adv7175), (PCB "M340-10") MPEG DVD decoder
-
-Formac
-------
- iProTV (Card for iMac Mezzanine slot, Bt848+SCSI)
- ProTV (Bt848)
- ProTV II = ProTV Stereo (Bt878) ["stereo" means FM stereo, tv is still mono]
-
-ATI
----
- TV-Wonder
- TV-Wonder VE
-
-Diamond Multimedia
-------------------
- DTV2000 (Bt848, tda9875)
-
-Aopen
------
- VA1000 Plus (w/ Stereo)
- VA1000 Lite
- VA1000 (=LR90)
-
-Intel
------
- Smart Video Recorder (ISA full-length)
- Smart Video Recorder pro (ISA half-length)
- Smart Video Recorder III (Bt848)
-
-STB
----
- STB Gateway 6000704 (bt878)
- STB Gateway 6000699 (bt848)
- STB Gateway 6000402 (bt848)
- STB TV130 PCI
-
-Videologic
-----------
- Captivator Pro/TV (ISA?)
- Captivator PCI/VC (Bt848 bundled with camera) (capture only)
-
-Technotrend
-------------
- TT-SAT PCI (PCB "Sat-PCI Rev.:1.3.1"; zr36125, vpx3225d, stc0056a, Tuner:BSKE6-155A
- TT-DVB-Sat
- revisions 1.1, 1.3, 1.5, 1.6 and 2.1
- This card is sold as OEM from:
- Siemens DVB-s Card
- Hauppauge WinTV DVB-S
- Technisat SkyStar 1 DVB
- Galaxis DVB Sat
- Now this card is called TT-PCline Premium Family
- TT-Budget (saa7146, bsru6-701a)
- This card is sold as OEM from:
- Hauppauge WinTV Nova
- Satelco Standard PCI (DVB-S)
- TT-DVB-C PCI
-
-Teles
------
- DVB-s (Rev. 2.2, BSRV2-301A, data only?)
-
-Remote Vision
--------------
- MX RV605 (Bt848 capture only)
-
-Boeder
-------
- PC ChatCam (Model 68252) (Bt848 capture only)
- Tv/Fm Capture Card (Model 68404) = PV951
-
-Media-Surfer (esc-kathrein.de)
--------------------------------
- Sat-Surfer (ISA)
- Sat-Surfer PCI = Techni-PC-Sat
- Cable-Surfer 1
- Cable-Surfer 2
- Cable-Surfer PCI (zr36120)
- Audio-Surfer (ISA Radio card)
-
-Jetway (www.jetway.com.tw)
---------------------------
- JW-TV 878M
- JW-TV 878 = KWorld KW-TV878RF
-
-Galaxis
--------
- Galaxis DVB Card S CI
- Galaxis DVB Card C CI
- Galaxis DVB Card S
- Galaxis DVB Card C
- Galaxis plug.in S [neuer Name: Galaxis DVB Card S CI
-
-Hauppauge
----------
- many many WinTV models ...
- WinTV DVBs = Technotrend Premium 1.3
- WinTV NOVA = Technotrend Budget 1.1 "S-DVB DATA"
- WinTV NOVA-CI "SDVBACI"
- WinTV Nova USB (=Technotrend USB 1.0)
- WinTV-Nexus-s (=Technotrend Premium 2.1 or 2.2)
- WinTV PVR
- WinTV PVR 250
- WinTV PVR 450
-
- US models
- 990 WinTV-PVR-350 (249USD) (iTVC15 chipset + radio)
- 980 WinTV-PVR-250 (149USD) (iTVC15 chipset)
- 880 WinTV-PVR-PCI (199USD) (KFIR chipset + bt878)
- 881 WinTV-PVR-USB
- 190 WinTV-GO
- 191 WinTV-GO-FM
- 404 WinTV
- 401 WinTV-radio
- 495 WinTV-Theater
- 602 WinTV-USB
- 621 WinTV-USB-FM
- 600 USB-Live
- 698 WinTV-HD
- 697 WinTV-D
- 564 WinTV-Nexus-S
-
- Deutsche Modelle
- 603 WinTV GO
- 719 WinTV Primio-FM
- 718 WinTV PCI-FM
- 497 WinTV Theater
- 569 WinTV USB
- 568 WinTV USB-FM
- 882 WinTV PVR
- 981 WinTV PVR 250
- 891 WinTV-PVR-USB
- 541 WinTV Nova
- 488 WinTV Nova-Ci
- 564 WinTV-Nexus-s
- 727 WinTV-DVB-c
- 545 Common Interface
- 898 WinTV-Nova-USB
-
- UK models
- 607 WinTV Go
- 693,793 WinTV Primio FM
- 647,747 WinTV PCI FM
- 498 WinTV Theater
- 883 WinTV PVR
- 893 WinTV PVR USB (Duplicate entry)
- 566 WinTV USB (UK)
- 573 WinTV USB FM
- 429 Impact VCB (bt848)
- 600 USB Live (Video-In 1x Comp, 1xSVHS)
- 542 WinTV Nova
- 717 WinTV DVB-S
- 909 Nova-t PCI
- 893 Nova-t USB (Duplicate entry)
- 802 MyTV
- 804 MyView
- 809 MyVideo
- 872 MyTV2Go FM
-
-
- 546 WinTV Nova-S CI
- 543 WinTV Nova
- 907 Nova-S USB
- 908 Nova-T USB
- 717 WinTV Nexus-S
- 157 DEC3000-s Standalone + USB
-
- Spain
- 685 WinTV-Go
- 690 WinTV-PrimioFM
- 416 WinTV-PCI Nicam Estereo
- 677 WinTV-PCI-FM
- 699 WinTV-Theater
- 683 WinTV-USB
- 678 WinTV-USB-FM
- 983 WinTV-PVR-250
- 883 WinTV-PVR-PCI
- 993 WinTV-PVR-350
- 893 WinTV-PVR-USB
- 728 WinTV-DVB-C PCI
- 832 MyTV2Go
- 869 MyTV2Go-FM
- 805 MyVideo (USB)
-
-
-Matrix-Vision
--------------
- MATRIX-Vision MV-Delta
- MATRIX-Vision MV-Delta 2
- MVsigma-SLC (Bt848)
-
-Conceptronic (.net)
-------------
- TVCON FM, TV card w/ FM = CPH05x
- TVCON = CPH06x
-
-BestData
---------
- HCC100 = VCC100rev1 + camera
- VCC100 rev1 (bt848)
- VCC100 rev2 (bt878)
-
-Gallant (www.gallantcom.com) www.minton.com.tw
------------------------------------------------
- Intervision IV-510 (capture only bt8x8)
- Intervision IV-550 (bt8x8)
- Intervision IV-100 (zoran)
- Intervision IV-1000 (bt8x8)
-
-Asonic (www.asonic.com.cn) (website down)
------------------------------------------
- SkyEye tv 878
-
-Hoontech
---------
- 878TV/FM
-
-Teppro (www.itcteppro.com.tw)
------------------------------
- ITC PCITV (Card Ver 1.0) "Teppro TV1/TVFM1 Card"
- ITC PCITV (Card Ver 2.0)
- ITC PCITV (Card Ver 3.0) = "PV-BT878P+ (REV.9D)"
- ITC PCITV (Card Ver 4.0)
- TEPPRO IV-550 (For BT848 Main Chip)
- ITC DSTTV (bt878, satellite)
- ITC VideoMaker (saa7146, StreamMachine sm2110, tvtuner) "PV-SM2210P+ (REV:1C)"
-
-Kworld (www.kworld.com.tw)
---------------------------
- PC TV Station
- KWORLD KW-TV878R TV (no radio)
- KWORLD KW-TV878RF TV (w/ radio)
-
- KWORLD KW-TVL878RF (low profile)
-
- KWORLD KW-TV713XRF (saa7134)
-
-
- MPEG TV Station (same cards as above plus WinDVR Software MPEG en/decoder)
- KWORLD KW-TV878R -Pro TV (no Radio)
- KWORLD KW-TV878RF-Pro TV (w/ Radio)
- KWORLD KW-TV878R -Ultra TV (no Radio)
- KWORLD KW-TV878RF-Ultra TV (w/ Radio)
-
-
-
-JTT/ Justy Corp.(http://www.jtt.ne.jp/)
----------------------------------------------------------------------
- JTT-02 (JTT TV) "TV watchmate pro" (bt848)
-
-ADS www.adstech.com
--------------------
- Channel Surfer TV ( CHX-950 )
- Channel Surfer TV+FM ( CHX-960FM )
-
-AVEC www.prochips.com
----------------------
- AVEC Intercapture (bt848, tea6320)
-
-NoBrand
--------
- TV Excel = Australian Name for "PV-BT878P+ 8E" or "878TV Rev.3_"
-
-Mach www.machspeed.com
-----
- Mach TV 878
-
-Eline www.eline-net.com/
------
- Eline Vision TVMaster / TVMaster FM (ELV-TVM/ ELV-TVM-FM) = LR26 (bt878)
- Eline Vision TVMaster-2000 (ELV-TVM-2000, ELV-TVM-2000-FM)= LR138 (saa713x)
-
-Spirit
-------
- Spirit TV Tuner/Video Capture Card (bt848)
-
-Boser www.boser.com.tw
------
- HS-878 Mini PCI Capture Add-on Card
- HS-879 Mini PCI 3D Audio and Capture Add-on Card (w/ ES1938 Solo-1)
-
-Satelco www.citycom-gmbh.de, www.satelco.de
--------
- TV-FM =KNC1 saa7134
- Standard PCI (DVB-S) = Technotrend Budget
- Standard PCI (DVB-S) w/ CI
- Satelco Highend PCI (DVB-S) = Technotrend Premium
-
-
-Sensoray www.sensoray.com
---------
- Sensoray 311 (PC/104 bus)
- Sensoray 611 (PCI)
-
-CEI (Chartered Electronics Industries Pte Ltd [CEI] [FCC ID HBY])
----
- TV Tuner - HBY-33A-RAFFLES Brooktree Bt848KPF + Philips
- TV Tuner MG9910 - HBY33A-TVO CEI + Philips SAA7110 + OKI M548262 + ST STV8438CV
- Primetime TV (ISA)
- acquired by Singapore Technologies
- now operating as Chartered Semiconductor Manufacturing
- Manufacturer of video cards is listed as:
- Cogent Electronics Industries [CEI]
-
-AITech
-------
- Wavewatcher TV (ISA)
- AITech WaveWatcher TV-PCI = can be LR26 (Bt848) or LR50 (BT878)
- WaveWatcher TVR-202 TV/FM Radio Card (ISA)
-
-MAXRON
-------
- Maxron MaxTV/FM Radio (KW-TV878-FNT) = Kworld or JW-TV878-FBK
-
-www.ids-imaging.de
-------------------
- Falcon Series (capture only)
- In USA: http://www.theimagingsource.com/
- DFG/LC1
-
-www.sknet-web.co.jp
--------------------
- SKnet Monster TV (saa7134)
-
-A-Max www.amaxhk.com (Colormax, Amax, Napa)
--------------------
- APAC Viewcomp 878
-
-Cybertainment
--------------
- CyberMail AV Video Email Kit w/ PCI Capture Card (capture only)
- CyberMail Xtreme
- These are Flyvideo
-
-VCR (http://www.vcrinc.com/)
----
- Video Catcher 16
-
-Twinhan
--------
- DST Card/DST-IP (bt878, twinhan asic) VP-1020
- Sold as:
- KWorld DVBS Satellite TV-Card
- Powercolor DSTV Satellite Tuner Card
- Prolink Pixelview DTV2000
- Provideo PV-911 Digital Satellite TV Tuner Card With Common Interface ?
- DST-CI Card (DVB Satellite) VP-1030
- DCT Card (DVB cable)
-
-MSI
----
- MSI TV@nywhere Tuner Card (MS-8876) (CX23881/883) Not Bt878 compatible.
- MS-8401 DVB-S
-
-Focus www.focusinfo.com
------
- InVideo PCI (bt878)
-
-Sdisilk www.sdisilk.com/
--------
- SDI Silk 100
- SDI Silk 200 SDI Input Card
-
-www.euresys.com
- PICOLO series
-
-PMC/Pace
-www.pacecom.co.uk website closed
-
-Mercury www.kobian.com (UK and FR)
- LR50
- LR138RBG-Rx == LR138
-
-TEC sound (package and manuals don't have any other manufacturer info) TecSound
- Though educated googling found: www.techmakers.com
- TV-Mate = Zoltrix VP-8482
-
-Lorenzen www.lorenzen.de
---------
- SL DVB-S PCI = Technotrend Budget PCI (su1278 or bsru version)
-
-Origo (.uk) www.origo2000.com
- PC TV Card = LR50
-
-I/O Magic www.iomagic.com
----------
- PC PVR - Desktop TV Personal Video Recorder DR-PCTV100 = Pinnacle ROB2D-51009464 4.0 + Cyberlink PowerVCR II
-
-Arowana
--------
- TV-Karte / Poso Power TV (?) = Zoltrix VP-8482 (?)
-
-iTVC15 boards:
--------------
-kuroutoshikou.com ITVC15
-yuan.com MPG160 PCI TV (Internal PCI MPEG2 encoder card plus TV-tuner)
-
-Asus www.asuscom.com
- Asus TV Tuner Card 880 NTSC (low profile, cx23880)
- Asus TV (saa7134)
-
-Hoontech
---------
-http://www.hoontech.de/
- HART Vision 848 (H-ART Vision 848)
- HART Vision 878 (H-Art Vision 878)
diff --git a/Documentation/video4linux/bttv/ICs b/Documentation/video4linux/bttv/ICs
deleted file mode 100644
index 611315f87c3e..000000000000
--- a/Documentation/video4linux/bttv/ICs
+++ /dev/null
@@ -1,37 +0,0 @@
-all boards:
-
-Brooktree Bt848/848A/849/878/879: video capture chip
-
-
-
-Miro PCTV:
-
-Philips or Temic Tuner
-
-
-
-Hauppauge Win/TV pci (version 405):
-
-Microchip 24LC02B or
-Philips 8582E2Y: 256 Byte EEPROM with configuration information
- I2C 0xa0-0xa1, (24LC02B also responds to 0xa2-0xaf)
-Philips SAA5246AGP/E: Videotext decoder chip, I2C 0x22-0x23
-TDA9800: sound decoder
-Winbond W24257AS-35: 32Kx8 CMOS static RAM (Videotext buffer mem)
-14052B: analog switch for selection of sound source
-
-PAL:
-TDA5737: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners
-TSA5522: 1.4 GHz I2C-bus controlled synthesizer, I2C 0xc2-0xc3
-
-NTSC:
-TDA5731: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners
-TSA5518: no datasheet available on Philips site
-
-
-
-STB TV pci:
-
-???
-if you want better support for STB cards send me info!
-Look at the board! What chips are on it?
diff --git a/Documentation/video4linux/bttv/Insmod-options b/Documentation/video4linux/bttv/Insmod-options
deleted file mode 100644
index 14c065fa23ef..000000000000
--- a/Documentation/video4linux/bttv/Insmod-options
+++ /dev/null
@@ -1,172 +0,0 @@
-
-Note: "modinfo <module>" prints various information about a kernel
-module, among them a complete and up-to-date list of insmod options.
-This list tends to be outdated because it is updated manually ...
-
-==========================================================================
-
-bttv.o
- the bt848/878 (grabber chip) driver
-
- insmod args:
- card=n card type, see CARDLIST for a list.
- tuner=n tuner type, see CARDLIST for a list.
- radio=0/1 card supports radio
- pll=0/1/2 pll settings
- 0: don't use PLL
- 1: 28 MHz crystal installed
- 2: 35 MHz crystal installed
-
- triton1=0/1 for Triton1 (+others) compatibility
- vsfx=0/1 yet another chipset bug compatibility bit
- see README.quirks for details on these two.
-
- bigendian=n Set the endianness of the gfx framebuffer.
- Default is native endian.
- fieldnr=0/1 Count fields. Some TV descrambling software
- needs this, for others it only generates
- 50 useless IRQs/sec. default is 0 (off).
- autoload=0/1 autoload helper modules (tuner, audio).
- default is 1 (on).
- bttv_verbose=0/1/2 verbose level (at insmod time, while
- looking at the hardware). default is 1.
- bttv_debug=0/1 debug messages (for capture).
- default is 0 (off).
- irq_debug=0/1 irq handler debug messages.
- default is 0 (off).
- gbuffers=2-32 number of capture buffers for mmap'ed capture.
- default is 4.
- gbufsize= size of capture buffers. default and
- maximum value is 0x208000 (~2MB)
- no_overlay=0 Enable overlay on broken hardware. There
- are some chipsets (SIS for example) which
- are known to have problems with the PCI DMA
- push used by bttv. bttv will disable overlay
- by default on this hardware to avoid crashes.
- With this insmod option you can override this.
- no_overlay=1 Disable overlay. It should be used by broken
- hardware that doesn't support PCI2PCI direct
- transfers.
- automute=0/1 Automatically mutes the sound if there is
- no TV signal, on by default. You might try
- to disable this if you have bad input signal
- quality which leading to unwanted sound
- dropouts.
- chroma_agc=0/1 AGC of chroma signal, off by default.
- adc_crush=0/1 Luminance ADC crush, on by default.
- i2c_udelay= Allow reduce I2C speed. Default is 5 usecs
- (meaning 66,67 Kbps). The default is the
- maximum supported speed by kernel bitbang
- algorithm. You may use lower numbers, if I2C
- messages are lost (16 is known to work on
- all supported cards).
-
- bttv_gpio=0/1
- gpiomask=
- audioall=
- audiomux=
- See Sound-FAQ for a detailed description.
-
- remap, card, radio and pll accept up to four comma-separated arguments
- (for multiple boards).
-
-tuner.o
- The tuner driver. You need this unless you want to use only
- with a camera or external tuner ...
-
- insmod args:
- debug=1 print some debug info to the syslog
- type=n type of the tuner chip. n as follows:
- see CARDLIST for a complete list.
- pal=[bdgil] select PAL variant (used for some tuners
- only, important for the audio carrier).
-
-tvaudio.o
- new, experimental module which is supported to provide a single
- driver for all simple i2c audio control chips (tda/tea*).
-
- insmod args:
- tda8425 = 1 enable/disable the support for the
- tda9840 = 1 various chips.
- tda9850 = 1 The tea6300 can't be autodetected and is
- tda9855 = 1 therefore off by default, if you have
- tda9873 = 1 this one on your card (STB uses these)
- tda9874a = 1 you have to enable it explicitly.
- tea6300 = 0 The two tda985x chips use the same i2c
- tea6420 = 1 address and can't be disturgished from
- pic16c54 = 1 each other, you might have to disable
- the wrong one.
- debug = 1 print debug messages
-
- insmod args for tda9874a:
- tda9874a_SIF=1/2 select sound IF input pin (1 or 2)
- (default is pin 1)
- tda9874a_AMSEL=0/1 auto-mute select for NICAM (default=0)
- Please read note 3 below!
- tda9874a_STD=n select TV sound standard (0..8):
- 0 - A2, B/G
- 1 - A2, M (Korea)
- 2 - A2, D/K (1)
- 3 - A2, D/K (2)
- 4 - A2, D/K (3)
- 5 - NICAM, I
- 6 - NICAM, B/G
- 7 - NICAM, D/K (default)
- 8 - NICAM, L
-
- Note 1: tda9874a supports both tda9874h (old) and tda9874a (new) chips.
- Note 2: tda9874h/a and tda9875 (which is supported separately by
- tda9875.o) use the same i2c address so both modules should not be
- used at the same time.
- Note 3: Using tda9874a_AMSEL option depends on your TV card design!
- AMSEL=0: auto-mute will switch between NICAM sound
- and the sound on 1st carrier (i.e. FM mono or AM).
- AMSEL=1: auto-mute will switch between NICAM sound
- and the analog mono input (MONOIN pin).
- If tda9874a decoder on your card has MONOIN pin not connected, then
- use only tda9874_AMSEL=0 or don't specify this option at all.
- For example:
- card=65 (FlyVideo 2000S) - set AMSEL=1 or AMSEL=0
- card=72 (Prolink PV-BT878P rev.9B) - set AMSEL=0 only
-
-msp3400.o
- The driver for the msp34xx sound processor chips. If you have a
- stereo card, you probably want to insmod this one.
-
- insmod args:
- debug=1/2 print some debug info to the syslog,
- 2 is more verbose.
- simple=1 Use the "short programming" method. Newer
- msp34xx versions support this. You need this
- for dbx stereo. Default is on if supported by
- the chip.
- once=1 Don't check the TV-stations Audio mode
- every few seconds, but only once after
- channel switches.
- amsound=1 Audio carrier is AM/NICAM at 6.5 Mhz. This
- should improve things for french people, the
- carrier autoscan seems to work with FM only...
-
-tea6300.o - OBSOLETE (use tvaudio instead)
- The driver for the tea6300 fader chip. If you have a stereo
- card and the msp3400.o doesn't work, you might want to try this
- one. This chip is seen on most STB TV/FM cards (usually from
- Gateway OEM sold surplus on auction sites).
-
- insmod args:
- debug=1 print some debug info to the syslog.
-
-tda8425.o - OBSOLETE (use tvaudio instead)
- The driver for the tda8425 fader chip. This driver used to be
- part of bttv.c, so if your sound used to work but does not
- anymore, try loading this module.
-
- insmod args:
- debug=1 print some debug info to the syslog.
-
-tda985x.o - OBSOLETE (use tvaudio instead)
- The driver for the tda9850/55 audio chips.
-
- insmod args:
- debug=1 print some debug info to the syslog.
- chip=9850/9855 set the chip type.
diff --git a/Documentation/video4linux/bttv/MAKEDEV b/Documentation/video4linux/bttv/MAKEDEV
deleted file mode 100644
index 093c0cd18042..000000000000
--- a/Documentation/video4linux/bttv/MAKEDEV
+++ /dev/null
@@ -1,27 +0,0 @@
-#!/bin/bash
-
-function makedev () {
-
- for dev in 0 1 2 3; do
- echo "/dev/$1$dev: char 81 $[ $2 + $dev ]"
- rm -f /dev/$1$dev
- mknod /dev/$1$dev c 81 $[ $2 + $dev ]
- chmod 666 /dev/$1$dev
- done
-
- # symlink for default device
- rm -f /dev/$1
- ln -s /dev/${1}0 /dev/$1
-}
-
-# see http://linux.bytesex.org/v4l2/API.html
-
-echo "*** new device names ***"
-makedev video 0
-makedev radio 64
-makedev vbi 224
-
-#echo "*** old device names (for compatibility only) ***"
-#makedev bttv 0
-#makedev bttv-fm 64
-#makedev bttv-vbi 224
diff --git a/Documentation/video4linux/bttv/Modprobe.conf b/Documentation/video4linux/bttv/Modprobe.conf
deleted file mode 100644
index 55f14650d8cd..000000000000
--- a/Documentation/video4linux/bttv/Modprobe.conf
+++ /dev/null
@@ -1,11 +0,0 @@
-# i2c
-alias char-major-89 i2c-dev
-options i2c-core i2c_debug=1
-options i2c-algo-bit bit_test=1
-
-# bttv
-alias char-major-81 videodev
-alias char-major-81-0 bttv
-options bttv card=2 radio=1
-options tuner debug=1
-
diff --git a/Documentation/video4linux/bttv/Modules.conf b/Documentation/video4linux/bttv/Modules.conf
deleted file mode 100644
index 8f258faf18f1..000000000000
--- a/Documentation/video4linux/bttv/Modules.conf
+++ /dev/null
@@ -1,14 +0,0 @@
-# For modern kernels (2.6 or above), this belongs in /etc/modprobe.d/*.conf
-# For for 2.4 kernels or earlier, this belongs in /etc/modules.conf.
-
-# i2c
-alias char-major-89 i2c-dev
-options i2c-core i2c_debug=1
-options i2c-algo-bit bit_test=1
-
-# bttv
-alias char-major-81 videodev
-alias char-major-81-0 bttv
-options bttv card=2 radio=1
-options tuner debug=1
-
diff --git a/Documentation/video4linux/bttv/PROBLEMS b/Documentation/video4linux/bttv/PROBLEMS
deleted file mode 100644
index 2b8b0079f7c7..000000000000
--- a/Documentation/video4linux/bttv/PROBLEMS
+++ /dev/null
@@ -1,62 +0,0 @@
-- Start capturing by pressing "c" or by selecting it via a menu!
-
-- Start capturing by pressing "c" or by selecting it via a menu!!!
-
-- The memory of some S3 cards is not recognized right:
-
- First of all, if you are not using XFree-3.2 or newer, upgrade AT LEAST to
- XFree-3.2A! This solved the problem for most people.
-
- Start up X11 like this: "XF86_S3 -probeonly" and write down where the
- linear frame buffer is.
- If it is different to the address found by bttv install bttv like this:
- "insmod bttv vidmem=0xfb0"
- if the linear frame buffer is at 0xfb000000 (i.e. omit the last 5 zeros!)
-
- Some S3 cards even take up 64MB of memory but only report 32MB to the BIOS.
- If this 64MB area overlaps the IO memory of the Bt848 you also have to
- remap this. E.g.: insmod bttv vidmem=0xfb0 remap=0xfa0
-
- If the video memory is found at the right place and there are no address
- conflicts but still no picture (or the computer even crashes),
- try disabling features of your PCI chipset in the BIOS setup.
-
- Frank Kapahnke <frank@kapahnke.prima.ruhr.de> also reported that problems
- with his S3 868 went away when he upgraded to XFree 3.2.
-
-
-- I still only get a black picture with my S3 card!
-
- Even with XFree-3.2A some people have problems with their S3 cards
- (mostly with Trio 64 but also with some others)
- Get the free demo version of Accelerated X from www.xinside.com and try
- bttv with it. bttv seems to work with most S3 cards with Accelerated X.
-
- Since I do not know much (better make that almost nothing) about VGA card
- programming I do not know the reason for this.
- Looks like XFree does something different when setting up the video memory?
- Maybe somebody can enlighten me?
- Would be nice if somebody could get this to work with XFree since
- Accelerated X costs more than some of the grabber cards ...
-
- Better linear frame buffer support for S3 cards will probably be in
- XFree 4.0.
-
-- Grabbing is not switched off when changing consoles with XFree.
- That's because XFree and some AcceleratedX versions do not send unmap
- events.
-
-- Some popup windows (e.g. of the window manager) are not refreshed.
-
- Disable backing store by starting X with the option "-bs"
-
-- When using 32 bpp in XFree or 24+8bpp mode in AccelX 3.1 the system
- can sometimes lock up if you use more than 1 bt848 card at the same time.
- You will always get pixel errors when e.g. using more than 1 card in full
- screen mode. Maybe we need something faster than the PCI bus ...
-
-
-- Some S3 cards and the Matrox Mystique will produce pixel errors with
- full resolution in 32-bit mode.
-
-- Some video cards have problems with Accelerated X 4.1
diff --git a/Documentation/video4linux/bttv/README b/Documentation/video4linux/bttv/README
deleted file mode 100644
index 7cbf4fb6cf31..000000000000
--- a/Documentation/video4linux/bttv/README
+++ /dev/null
@@ -1,90 +0,0 @@
-
-Release notes for bttv
-======================
-
-You'll need at least these config options for bttv:
- CONFIG_I2C=m
- CONFIG_I2C_ALGOBIT=m
- CONFIG_VIDEO_DEV=m
-
-The latest bttv version is available from http://bytesex.org/bttv/
-
-
-Make bttv work with your card
------------------------------
-
-Just try "modprobe bttv" and see if that works.
-
-If it doesn't bttv likely could not autodetect your card and needs some
-insmod options. The most important insmod option for bttv is "card=n"
-to select the correct card type. If you get video but no sound you've
-very likely specified the wrong (or no) card type. A list of supported
-cards is in CARDLIST.bttv
-
-If bttv takes very long to load (happens sometimes with the cheap
-cards which have no tuner), try adding this to your modules.conf:
- options i2c-algo-bit bit_test=1
-
-For the WinTV/PVR you need one firmware file from the driver CD:
-hcwamc.rbf. The file is in the pvr45xxx.exe archive (self-extracting
-zip file, unzip can unpack it). Put it into the /etc/pvr directory or
-use the firm_altera=<path> insmod option to point the driver to the
-location of the file.
-
-If your card isn't listed in CARDLIST.bttv or if you have trouble making
-audio work, you should read the Sound-FAQ.
-
-
-Autodetecting cards
--------------------
-
-bttv uses the PCI Subsystem ID to autodetect the card type. lspci lists
-the Subsystem ID in the second line, looks like this:
-
-00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 (rev 02)
- Subsystem: Hauppauge computer works Inc. WinTV/GO
- Flags: bus master, medium devsel, latency 32, IRQ 5
- Memory at e2000000 (32-bit, prefetchable) [size=4K]
-
-only bt878-based cards can have a subsystem ID (which does not mean
-that every card really has one). bt848 cards can't have a Subsystem
-ID and therefore can't be autodetected. There is a list with the ID's
-in bttv-cards.c (in case you are intrested or want to mail patches
-with updates).
-
-
-Still doesn't work?
--------------------
-
-I do NOT have a lab with 30+ different grabber boards and a
-PAL/NTSC/SECAM test signal generator at home, so I often can't
-reproduce your problems. This makes debugging very difficult for me.
-If you have some knowledge and spare time, please try to fix this
-yourself (patches very welcome of course...) You know: The linux
-slogan is "Do it yourself".
-
-There is a mailing list: linux-media@vger.kernel.org
-http://vger.kernel.org/vger-lists.html#linux-media
-
-If you have trouble with some specific TV card, try to ask there
-instead of mailing me directly. The chance that someone with the
-same card listens there is much higher...
-
-For problems with sound: There are a lot of different systems used
-for TV sound all over the world. And there are also different chips
-which decode the audio signal. Reports about sound problems ("stereo
-does'nt work") are pretty useless unless you include some details
-about your hardware and the TV sound scheme used in your country (or
-at least the country you are living in).
-
-
-Finally: If you mail some patches for bttv around the world (to
-linux-kernel/Alan/Linus/...), please Cc: me.
-
-
-Have fun with bttv,
-
- Gerd
-
---
-Gerd Knorr <kraxel@bytesex.org>
diff --git a/Documentation/video4linux/bttv/README.WINVIEW b/Documentation/video4linux/bttv/README.WINVIEW
deleted file mode 100644
index c61cf2864287..000000000000
--- a/Documentation/video4linux/bttv/README.WINVIEW
+++ /dev/null
@@ -1,33 +0,0 @@
-
-Support for the Leadtek WinView 601 TV/FM by Jon Tombs <jon@gte.esi.us.es>
-
-This card is basically the same as all the rest (Bt484A, Philips tuner),
-the main difference is that they have attached a programmable attenuator to 3
-GPIO lines in order to give some volume control. They have also stuck an
-infra-red remote control decoded on the board, I will add support for this
-when I get time (it simple generates an interrupt for each key press, with
-the key code is placed in the GPIO port).
-
-I don't yet have any application to test the radio support. The tuner
-frequency setting should work but it is possible that the audio multiplexer
-is wrong. If it doesn't work, send me email.
-
-
-- No Thanks to Leadtek they refused to answer any questions about their
-hardware. The driver was written by visual inspection of the card. If you
-use this driver, send an email insult to them, and tell them you won't
-continue buying their hardware unless they support Linux.
-
-- Little thanks to Princeton Technology Corp (http://www.princeton.com.tw)
-who make the audio attenuator. Their publicly available data-sheet available
-on their web site doesn't include the chip programming information! Hidden
-on their server are the full data-sheets, but don't ask how I found it.
-
-To use the driver I use the following options, the tuner and pll settings might
-be different in your country
-
-insmod videodev
-insmod i2c scan=1 i2c_debug=0 verbose=0
-insmod tuner type=1 debug=0
-insmod bttv pll=1 radio=1 card=17
-
diff --git a/Documentation/video4linux/bttv/README.freeze b/Documentation/video4linux/bttv/README.freeze
deleted file mode 100644
index 5eddfa076cfb..000000000000
--- a/Documentation/video4linux/bttv/README.freeze
+++ /dev/null
@@ -1,74 +0,0 @@
-
-If the box freezes hard with bttv ...
-=====================================
-
-It might be a bttv driver bug. It also might be bad hardware. It also
-might be something else ...
-
-Just mailing me "bttv freezes" isn't going to help much. This README
-has a few hints how you can help to pin down the problem.
-
-
-bttv bugs
----------
-
-If some version works and another doesn't it is likely to be a driver
-bug. It is very helpful if you can tell where exactly it broke
-(i.e. the last working and the first broken version).
-
-With a hard freeze you probably doesn't find anything in the logfiles.
-The only way to capture any kernel messages is to hook up a serial
-console and let some terminal application log the messages. /me uses
-screen. See Documentation/serial-console.txt for details on setting
-up a serial console.
-
-Read Documentation/oops-tracing.txt to learn how to get any useful
-information out of a register+stack dump printed by the kernel on
-protection faults (so-called "kernel oops").
-
-If you run into some kind of deadlock, you can try to dump a call trace
-for each process using sysrq-t (see Documentation/sysrq.txt).
-This way it is possible to figure where *exactly* some process in "D"
-state is stuck.
-
-I've seen reports that bttv 0.7.x crashes whereas 0.8.x works rock solid
-for some people. Thus probably a small buglet left somewhere in bttv
-0.7.x. I have no idea where exactly, it works stable for me and a lot of
-other people. But in case you have problems with the 0.7.x versions you
-can give 0.8.x a try ...
-
-
-hardware bugs
--------------
-
-Some hardware can't deal with PCI-PCI transfers (i.e. grabber => vga).
-Sometimes problems show up with bttv just because of the high load on
-the PCI bus. The bt848/878 chips have a few workarounds for known
-incompatibilities, see README.quirks.
-
-Some folks report that increasing the pci latency helps too,
-althrought I'm not sure whenever this really fixes the problems or
-only makes it less likely to happen. Both bttv and btaudio have a
-insmod option to set the PCI latency of the device.
-
-Some mainboard have problems to deal correctly with multiple devices
-doing DMA at the same time. bttv + ide seems to cause this sometimes,
-if this is the case you likely see freezes only with video and hard disk
-access at the same time. Updating the IDE driver to get the latest and
-greatest workarounds for hardware bugs might fix these problems.
-
-
-other
------
-
-If you use some binary-only yunk (like nvidia module) try to reproduce
-the problem without.
-
-IRQ sharing is known to cause problems in some cases. It works just
-fine in theory and many configurations. Neverless it might be worth a
-try to shuffle around the PCI cards to give bttv another IRQ or make
-it share the IRQ with some other piece of hardware. IRQ sharing with
-VGA cards seems to cause trouble sometimes. I've also seen funny
-effects with bttv sharing the IRQ with the ACPI bridge (and
-apci-enabled kernel).
-
diff --git a/Documentation/video4linux/bttv/README.quirks b/Documentation/video4linux/bttv/README.quirks
deleted file mode 100644
index 92e03929a6b2..000000000000
--- a/Documentation/video4linux/bttv/README.quirks
+++ /dev/null
@@ -1,83 +0,0 @@
-
-Below is what the bt878 data book says about the PCI bug compatibility
-modes of the bt878 chip.
-
-The triton1 insmod option sets the EN_TBFX bit in the control register.
-The vsfx insmod option does the same for EN_VSFX bit. If you have
-stability problems you can try if one of these options makes your box
-work solid.
-
-drivers/pci/quirks.c knows about these issues, this way these bits are
-enabled automagically for known-buggy chipsets (look at the kernel
-messages, bttv tells you).
-
-HTH,
-
- Gerd
-
----------------------------- cut here --------------------------
-
-Normal PCI Mode
----------------
-
-The PCI REQ signal is the logical-or of the incoming function requests.
-The inter-nal GNT[0:1] signals are gated asynchronously with GNT and
-demultiplexed by the audio request signal. Thus the arbiter defaults to
-the video function at power-up and parks there during no requests for
-bus access. This is desirable since the video will request the bus more
-often. However, the audio will have highest bus access priority. Thus
-the audio will have first access to the bus even when issuing a request
-after the video request but before the PCI external arbiter has granted
-access to the Bt879. Neither function can preempt the other once on the
-bus. The duration to empty the entire video PCI FIFO onto the PCI bus is
-very short compared to the bus access latency the audio PCI FIFO can
-tolerate.
-
-
-430FX Compatibility Mode
-------------------------
-
-When using the 430FX PCI, the following rules will ensure
-compatibility:
-
- (1) Deassert REQ at the same time as asserting FRAME.
- (2) Do not reassert REQ to request another bus transaction until after
- finish-ing the previous transaction.
-
-Since the individual bus masters do not have direct control of REQ, a
-simple logical-or of video and audio requests would violate the rules.
-Thus, both the arbiter and the initiator contain 430FX compatibility
-mode logic. To enable 430FX mode, set the EN_TBFX bit as indicated in
-Device Control Register on page 104.
-
-When EN_TBFX is enabled, the arbiter ensures that the two compatibility
-rules are satisfied. Before GNT is asserted by the PCI arbiter, this
-internal arbiter may still logical-or the two requests. However, once
-the GNT is issued, this arbiter must lock in its decision and now route
-only the granted request to the REQ pin. The arbiter decision lock
-happens regardless of the state of FRAME because it does not know when
-FRAME will be asserted (typically - each initiator will assert FRAME on
-the cycle following GNT). When FRAME is asserted, it is the initiator s
-responsibility to remove its request at the same time. It is the
-arbiters responsibility to allow this request to flow through to REQ and
-not allow the other request to hold REQ asserted. The decision lock may
-be removed at the end of the transaction: for example, when the bus is
-idle (FRAME and IRDY). The arbiter decision may then continue
-asynchronously until GNT is again asserted.
-
-
-Interfacing with Non-PCI 2.1 Compliant Core Logic
--------------------------------------------------
-
-A small percentage of core logic devices may start a bus transaction
-during the same cycle that GNT is de-asserted. This is non PCI 2.1
-compliant. To ensure compatibility when using PCs with these PCI
-controllers, the EN_VSFX bit must be enabled (refer to Device Control
-Register on page 104). When in this mode, the arbiter does not pass GNT
-to the internal functions unless REQ is asserted. This prevents a bus
-transaction from starting the same cycle as GNT is de-asserted. This
-also has the side effect of not being able to take advantage of bus
-parking, thus lowering arbitration performance. The Bt879 drivers must
-query for these non-compliant devices, and set the EN_VSFX bit only if
-required.
-
diff --git a/Documentation/video4linux/bttv/Sound-FAQ b/Documentation/video4linux/bttv/Sound-FAQ
deleted file mode 100644
index 646a47de0016..000000000000
--- a/Documentation/video4linux/bttv/Sound-FAQ
+++ /dev/null
@@ -1,148 +0,0 @@
-
-bttv and sound mini howto
-=========================
-
-There are a lot of different bt848/849/878/879 based boards available.
-Making video work often is not a big deal, because this is handled
-completely by the bt8xx chip, which is common on all boards. But
-sound is handled in slightly different ways on each board.
-
-To handle the grabber boards correctly, there is a array tvcards[] in
-bttv-cards.c, which holds the information required for each board.
-Sound will work only, if the correct entry is used (for video it often
-makes no difference). The bttv driver prints a line to the kernel
-log, telling which card type is used. Like this one:
-
- bttv0: model: BT848(Hauppauge old) [autodetected]
-
-You should verify this is correct. If it isn't, you have to pass the
-correct board type as insmod argument, "insmod bttv card=2" for
-example. The file CARDLIST has a list of valid arguments for card.
-If your card isn't listed there, you might check the source code for
-new entries which are not listed yet. If there isn't one for your
-card, you can check if one of the existing entries does work for you
-(just trial and error...).
-
-Some boards have an extra processor for sound to do stereo decoding
-and other nice features. The msp34xx chips are used by Hauppauge for
-example. If your board has one, you might have to load a helper
-module like msp3400.o to make sound work. If there isn't one for the
-chip used on your board: Bad luck. Start writing a new one. Well,
-you might want to check the video4linux mailing list archive first...
-
-Of course you need a correctly installed soundcard unless you have the
-speakers connected directly to the grabber board. Hint: check the
-mixer settings too. ALSA for example has everything muted by default.
-
-
-How sound works in detail
-=========================
-
-Still doesn't work? Looks like some driver hacking is required.
-Below is a do-it-yourself description for you.
-
-The bt8xx chips have 32 general purpose pins, and registers to control
-these pins. One register is the output enable register
-(BT848_GPIO_OUT_EN), it says which pins are actively driven by the
-bt848 chip. Another one is the data register (BT848_GPIO_DATA), where
-you can get/set the status if these pins. They can be used for input
-and output.
-
-Most grabber board vendors use these pins to control an external chip
-which does the sound routing. But every board is a little different.
-These pins are also used by some companies to drive remote control
-receiver chips. Some boards use the i2c bus instead of the gpio pins
-to connect the mux chip.
-
-As mentioned above, there is a array which holds the required
-information for each known board. You basically have to create a new
-line for your board. The important fields are these two:
-
-struct tvcard
-{
- [ ... ]
- u32 gpiomask;
- u32 audiomux[6]; /* Tuner, Radio, external, internal, mute, stereo */
-};
-
-gpiomask specifies which pins are used to control the audio mux chip.
-The corresponding bits in the output enable register
-(BT848_GPIO_OUT_EN) will be set as these pins must be driven by the
-bt848 chip.
-
-The audiomux[] array holds the data values for the different inputs
-(i.e. which pins must be high/low for tuner/mute/...). This will be
-written to the data register (BT848_GPIO_DATA) to switch the audio
-mux.
-
-
-What you have to do is figure out the correct values for gpiomask and
-the audiomux array. If you have Windows and the drivers four your
-card installed, you might to check out if you can read these registers
-values used by the windows driver. A tool to do this is available
-from ftp://telepresence.dmem.strath.ac.uk/pub/bt848/winutil, but it
-does'nt work with bt878 boards according to some reports I received.
-Another one with bt878 support is available from
-http://btwincap.sourceforge.net/Files/btspy2.00.zip
-
-You might also dig around in the *.ini files of the Windows applications.
-You can have a look at the board to see which of the gpio pins are
-connected at all and then start trial-and-error ...
-
-
-Starting with release 0.7.41 bttv has a number of insmod options to
-make the gpio debugging easier:
-
-bttv_gpio=0/1 enable/disable gpio debug messages
-gpiomask=n set the gpiomask value
-audiomux=i,j,... set the values of the audiomux array
-audioall=a set the values of the audiomux array (one
- value for all array elements, useful to check
- out which effect the particular value has).
-
-The messages printed with bttv_gpio=1 look like this:
-
- bttv0: gpio: en=00000027, out=00000024 in=00ffffd8 [audio: off]
-
-en = output _en_able register (BT848_GPIO_OUT_EN)
-out = _out_put bits of the data register (BT848_GPIO_DATA),
- i.e. BT848_GPIO_DATA & BT848_GPIO_OUT_EN
-in = _in_put bits of the data register,
- i.e. BT848_GPIO_DATA & ~BT848_GPIO_OUT_EN
-
-
-
-Other elements of the tvcards array
-===================================
-
-If you are trying to make a new card work you might find it useful to
-know what the other elements in the tvcards array are good for:
-
-video_inputs - # of video inputs the card has
-audio_inputs - historical cruft, not used any more.
-tuner - which input is the tuner
-svhs - which input is svhs (all others are labeled composite)
-muxsel - video mux, input->registervalue mapping
-pll - same as pll= insmod option
-tuner_type - same as tuner= insmod option
-*_modulename - hint whenever some card needs this or that audio
- module loaded to work properly.
-has_radio - whenever this TV card has a radio tuner.
-no_msp34xx - "1" disables loading of msp3400.o module
-no_tda9875 - "1" disables loading of tda9875.o module
-needs_tvaudio - set to "1" to load tvaudio.o module
-
-If some config item is specified both from the tvcards array and as
-insmod option, the insmod option takes precedence.
-
-
-
-Good luck,
-
- Gerd
-
-
-PS: If you have a new working entry, mail it to me.
-
---
-Gerd Knorr <kraxel@bytesex.org>
diff --git a/Documentation/video4linux/bttv/Specs b/Documentation/video4linux/bttv/Specs
deleted file mode 100644
index f32466cdae05..000000000000
--- a/Documentation/video4linux/bttv/Specs
+++ /dev/null
@@ -1,3 +0,0 @@
-Philips http://www.Semiconductors.COM/pip/
-Conexant http://www.conexant.com/
-Micronas http://www.micronas.com/en/home/index.html
diff --git a/Documentation/video4linux/bttv/THANKS b/Documentation/video4linux/bttv/THANKS
deleted file mode 100644
index 950aa781c2e9..000000000000
--- a/Documentation/video4linux/bttv/THANKS
+++ /dev/null
@@ -1,24 +0,0 @@
-Many thanks to:
-
-- Markus Schroeder <schroedm@uni-duesseldorf.de> for information on the Bt848
- and tuner programming and his control program xtvc.
-
-- Martin Buck <martin-2.buck@student.uni-ulm.de> for his great Videotext
- package.
-
-- Gerd Knorr <kraxel@cs.tu-berlin.de> for the MSP3400 support and the modular
- I2C, tuner, ... support.
-
-
-- MATRIX Vision for giving us 2 cards for free, which made support of
- single crystal operation possible.
-
-- MIRO for providing a free PCTV card and detailed information about the
- components on their cards. (E.g. how the tuner type is detected)
- Without their card I could not have debugged the NTSC mode.
-
-- Hauppauge for telling how the sound input is selected and what components
- they do and will use on their radio cards.
- Also many thanks for faxing me the FM1216 data sheet.
-
-
--
2.7.4
next prev parent reply other threads:[~2016-07-18 18:30 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-07-18 18:30 [PATCH 00/18] Complete moving media documentation to ReST format Mauro Carvalho Chehab
2016-07-18 18:30 ` Mauro Carvalho Chehab [this message]
2016-07-18 18:30 ` [PATCH 02/18] [media] doc-rst: add documentation for bttv driver Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 03/18] [media] doc-rst: add documentation for tuners Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 04/18] [media] doc-rst: start adding documentation for cx2341x Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 05/18] [media] cx2341x.rst: add fw-decoder-registers.txt content Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 06/18] [media] cx2341x.rst: Add the contents of fw-encoder-api.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 07/18] [media] cx2341x.rst: add the contents of fw-calling.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 08/18] [media] cx2341x.rst: add contents of fw-dma.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 09/18] [media] cx2341x.rst: add contents of fw-memory.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 10/18] [media] cx2341x.rst: add the contents of fw-upload.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 11/18] [media] cx2341x.rst: add contents of fw-osd-api.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 12/18] [media] cx2341x: add contents of README.hm12 Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 13/18] [media] cx2341x.rst: add contents of README.vbi Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 14/18] [media] cx88.rst: add contents from not-in-cx2388x-datasheet.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 15/18] [media] cx88.rst: add contents of hauppauge-wintv-cx88-ir.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 16/18] [media] get rid of Documentation/video4linux/lifeview.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 17/18] [media] doc-rst: fix media kAPI documentation Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 18/18] [media] doc-rst: better name the media books Mauro Carvalho Chehab
2016-07-19 9:19 ` [PATCH 00/18] Complete moving media documentation to ReST format Hans Verkuil
2016-07-19 11:12 ` Mauro Carvalho Chehab
2016-07-19 12:31 ` Markus Heiser
2016-07-19 14:53 ` Mauro Carvalho Chehab
2016-07-19 15:40 ` Mauro Carvalho Chehab
2016-07-19 16:42 ` Markus Heiser
2016-07-19 17:18 ` Mauro Carvalho Chehab
2016-07-21 15:17 ` Markus Heiser
2016-07-22 9:46 ` Mauro Carvalho Chehab
2016-07-22 10:55 ` Markus Heiser
2016-07-19 22:49 ` Jonathan Corbet
2016-07-20 0:00 ` Mauro Carvalho Chehab
2016-07-20 6:07 ` Markus Heiser
2016-07-20 10:19 ` Mauro Carvalho Chehab
2016-07-20 23:28 ` Jonathan Corbet
2016-07-21 14:41 ` Markus Heiser
2016-07-21 16:59 ` Jonathan Corbet
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=2287cb47fb6bc16c0f7e08756eb1541204a130de.1468865380.git.mchehab@s-opensource.com \
--to=mchehab@s-opensource.com \
--cc=corbet@lwn.net \
--cc=keescook@chromium.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@infradead.org \
--cc=paulmck@linux.vnet.ibm.com \
--cc=rdunlap@infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.