From: Mauro Carvalho Chehab <mchehab@s-opensource.com>
To: Linux Media Mailing List <linux-media@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>,
Mauro Carvalho Chehab <mchehab@infradead.org>,
Jonathan Corbet <corbet@lwn.net>,
linux-doc@vger.kernel.org
Subject: [PATCH 04/18] [media] doc-rst: start adding documentation for cx2341x
Date: Mon, 18 Jul 2016 15:30:26 -0300 [thread overview]
Message-ID: <a785ddb8686e5bf07624e23790acf08e1beddd7a.1468865380.git.mchehab@s-opensource.com> (raw)
In-Reply-To: <cover.1468865380.git.mchehab@s-opensource.com>
In-Reply-To: <cover.1468865380.git.mchehab@s-opensource.com>
move the contents of fw-decoder-api.txt to cx2341x and
convert it to ReST file, adding it to media/v4l-drivers
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
---
Documentation/media/v4l-drivers/cx2341x.rst | 564 +++++++++++++++++++++
Documentation/media/v4l-drivers/index.rst | 1 +
.../video4linux/cx2341x/fw-decoder-api.txt | 297 -----------
3 files changed, 565 insertions(+), 297 deletions(-)
create mode 100644 Documentation/media/v4l-drivers/cx2341x.rst
delete mode 100644 Documentation/video4linux/cx2341x/fw-decoder-api.txt
diff --git a/Documentation/media/v4l-drivers/cx2341x.rst b/Documentation/media/v4l-drivers/cx2341x.rst
new file mode 100644
index 000000000000..6f4ac07f52cd
--- /dev/null
+++ b/Documentation/media/v4l-drivers/cx2341x.rst
@@ -0,0 +1,564 @@
+The cx2341x driver
+==================
+
+Decoder firmware API description
+--------------------------------
+
+.. note:: this API is part of the decoder firmware, so it's cx23415 only.
+
+
+
+CX2341X_DEC_PING_FW
+-------------------
+
+Enum: 0/0x00
+
+Description
+~~~~~~~~~~~
+
+This API call does nothing. It may be used to check if the firmware
+is responding.
+
+
+
+CX2341X_DEC_START_PLAYBACK
+--------------------------
+
+Enum: 1/0x01
+
+Description
+~~~~~~~~~~~
+
+Begin or resume playback.
+
+Param[0]
+~~~~~~~~
+
+0 based frame number in GOP to begin playback from.
+
+Param[1]
+~~~~~~~~
+
+Specifies the number of muted audio frames to play before normal
+audio resumes. (This is not implemented in the firmware, leave at 0)
+
+
+
+CX2341X_DEC_STOP_PLAYBACK
+-------------------------
+
+Enum: 2/0x02
+
+Description
+~~~~~~~~~~~
+
+Ends playback and clears all decoder buffers. If PTS is not zero,
+playback stops at specified PTS.
+
+Param[0]
+~~~~~~~~
+
+Display 0=last frame, 1=black
+
+.. note::
+
+ this takes effect immediately, so if you want to wait for a PTS,
+ then use '0', otherwise the screen goes to black at once.
+ You can call this later (even if there is no playback) with a 1 value
+ to set the screen to black.
+
+Param[1]
+~~~~~~~~
+
+PTS low
+
+Param[2]
+~~~~~~~~
+
+PTS high
+
+
+
+CX2341X_DEC_SET_PLAYBACK_SPEED
+------------------------------
+
+Enum: 3/0x03
+
+Description
+~~~~~~~~~~~
+
+Playback stream at speed other than normal. There are two modes of
+operation:
+
+ - Smooth: host transfers entire stream and firmware drops unused
+ frames.
+ - Coarse: host drops frames based on indexing as required to achieve
+ desired speed.
+
+Param[0]
+~~~~~~~~
+
+.. code-block:: none
+
+ Bitmap:
+ 0:7 0 normal
+ 1 fast only "1.5 times"
+ n nX fast, 1/nX slow
+ 30 Framedrop:
+ '0' during 1.5 times play, every other B frame is dropped
+ '1' during 1.5 times play, stream is unchanged (bitrate
+ must not exceed 8mbps)
+ 31 Speed:
+ '0' slow
+ '1' fast
+
+.. note::
+
+ n is limited to 2. Anything higher does not result in
+ faster playback. Instead the host should start dropping frames.
+
+Param[1]
+~~~~~~~~
+
+Direction: 0=forward, 1=reverse
+
+.. note::
+
+ to make reverse playback work you have to write full GOPs in
+ reverse order.
+
+Param[2]
+~~~~~~~~
+
+.. code-block:: none
+
+ Picture mask:
+ 1=I frames
+ 3=I, P frames
+ 7=I, P, B frames
+
+Param[3]
+~~~~~~~~
+
+B frames per GOP (for reverse play only)
+
+.. note::
+
+ for reverse playback the Picture Mask should be set to I or I, P.
+ Adding B frames to the mask will result in corrupt video. This field
+ has to be set to the correct value in order to keep the timing correct.
+
+Param[4]
+~~~~~~~~
+
+Mute audio: 0=disable, 1=enable
+
+Param[5]
+~~~~~~~~
+
+Display 0=frame, 1=field
+
+Param[6]
+~~~~~~~~
+
+Specifies the number of muted audio frames to play before normal audio
+resumes. (Not implemented in the firmware, leave at 0)
+
+
+
+CX2341X_DEC_STEP_VIDEO
+----------------------
+
+Enum: 5/0x05
+
+Description
+~~~~~~~~~~~
+
+Each call to this API steps the playback to the next unit defined below
+in the current playback direction.
+
+Param[0]
+~~~~~~~~
+
+0=frame, 1=top field, 2=bottom field
+
+
+
+CX2341X_DEC_SET_DMA_BLOCK_SIZE
+------------------------------
+
+Enum: 8/0x08
+
+Description
+~~~~~~~~~~~
+
+Set DMA transfer block size. Counterpart to API 0xC9
+
+Param[0]
+~~~~~~~~
+
+DMA transfer block size in bytes. A different size may be specified
+when issuing the DMA transfer command.
+
+
+
+CX2341X_DEC_GET_XFER_INFO
+-------------------------
+
+Enum: 9/0x09
+
+Description
+~~~~~~~~~~~
+
+This API call may be used to detect an end of stream condition.
+
+Result[0]
+~~~~~~~~~
+
+Stream type
+
+Result[1]
+~~~~~~~~~
+
+Address offset
+
+Result[2]
+~~~~~~~~~
+
+Maximum bytes to transfer
+
+Result[3]
+~~~~~~~~~
+
+Buffer fullness
+
+
+
+CX2341X_DEC_GET_DMA_STATUS
+--------------------------
+
+Enum: 10/0x0A
+
+Description
+~~~~~~~~~~~
+
+Status of the last DMA transfer
+
+Result[0]
+~~~~~~~~~
+
+Bit 1 set means transfer complete
+Bit 2 set means DMA error
+Bit 3 set means linked list error
+
+Result[1]
+~~~~~~~~~
+
+DMA type: 0=MPEG, 1=OSD, 2=YUV
+
+
+
+CX2341X_DEC_SCHED_DMA_FROM_HOST
+-------------------------------
+
+Enum: 11/0x0B
+
+Description
+~~~~~~~~~~~
+
+Setup DMA from host operation. Counterpart to API 0xCC
+
+Param[0]
+~~~~~~~~
+
+Memory address of link list
+
+Param[1]
+~~~~~~~~
+
+Total # of bytes to transfer
+
+Param[2]
+~~~~~~~~
+
+DMA type (0=MPEG, 1=OSD, 2=YUV)
+
+
+
+CX2341X_DEC_PAUSE_PLAYBACK
+--------------------------
+
+Enum: 13/0x0D
+
+Description
+~~~~~~~~~~~
+
+Freeze playback immediately. In this mode, when internal buffers are
+full, no more data will be accepted and data request IRQs will be
+masked.
+
+Param[0]
+~~~~~~~~
+
+Display: 0=last frame, 1=black
+
+
+
+CX2341X_DEC_HALT_FW
+-------------------
+
+Enum: 14/0x0E
+
+Description
+~~~~~~~~~~~
+
+The firmware is halted and no further API calls are serviced until
+the firmware is uploaded again.
+
+
+
+CX2341X_DEC_SET_STANDARD
+------------------------
+
+Enum: 16/0x10
+
+Description
+~~~~~~~~~~~
+
+Selects display standard
+
+Param[0]
+~~~~~~~~
+
+0=NTSC, 1=PAL
+
+
+
+CX2341X_DEC_GET_VERSION
+-----------------------
+
+Enum: 17/0x11
+
+Description
+~~~~~~~~~~~
+
+Returns decoder firmware version information
+
+Result[0]
+~~~~~~~~~
+
+Version bitmask:
+ - Bits 0:15 build
+ - Bits 16:23 minor
+ - Bits 24:31 major
+
+
+
+CX2341X_DEC_SET_STREAM_INPUT
+----------------------------
+
+Enum: 20/0x14
+
+Description
+~~~~~~~~~~~
+
+Select decoder stream input port
+
+Param[0]
+~~~~~~~~
+
+0=memory (default), 1=streaming
+
+
+
+CX2341X_DEC_GET_TIMING_INFO
+---------------------------
+
+Enum: 21/0x15
+
+Description
+~~~~~~~~~~~
+
+Returns timing information from start of playback
+
+Result[0]
+~~~~~~~~~
+
+Frame count by decode order
+
+Result[1]
+~~~~~~~~~
+
+Video PTS bits 0:31 by display order
+
+Result[2]
+~~~~~~~~~
+
+Video PTS bit 32 by display order
+
+Result[3]
+~~~~~~~~~
+
+SCR bits 0:31 by display order
+
+Result[4]
+~~~~~~~~~
+
+SCR bit 32 by display order
+
+
+
+CX2341X_DEC_SET_AUDIO_MODE
+--------------------------
+
+Enum: 22/0x16
+
+Description
+~~~~~~~~~~~
+
+Select audio mode
+
+Param[0]
+~~~~~~~~
+
+Dual mono mode action
+ 0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged
+
+Param[1]
+~~~~~~~~
+
+Stereo mode action:
+ 0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged
+
+
+
+CX2341X_DEC_SET_EVENT_NOTIFICATION
+----------------------------------
+
+Enum: 23/0x17
+
+Description
+~~~~~~~~~~~
+
+Setup firmware to notify the host about a particular event.
+Counterpart to API 0xD5
+
+Param[0]
+~~~~~~~~
+
+Event:
+ - 0=Audio mode change between mono, (joint) stereo and dual channel.
+ - 3=Decoder started
+ - 4=Unknown: goes off 10-15 times per second while decoding.
+ - 5=Some sync event: goes off once per frame.
+
+Param[1]
+~~~~~~~~
+
+Notification 0=disabled, 1=enabled
+
+Param[2]
+~~~~~~~~
+
+Interrupt bit
+
+Param[3]
+~~~~~~~~
+
+Mailbox slot, -1 if no mailbox required.
+
+
+
+CX2341X_DEC_SET_DISPLAY_BUFFERS
+-------------------------------
+
+Enum: 24/0x18
+
+Description
+~~~~~~~~~~~
+
+Number of display buffers. To decode all frames in reverse playback you
+must use nine buffers.
+
+Param[0]
+~~~~~~~~
+
+0=six buffers, 1=nine buffers
+
+
+
+CX2341X_DEC_EXTRACT_VBI
+-----------------------
+
+Enum: 25/0x19
+
+Description
+~~~~~~~~~~~
+
+Extracts VBI data
+
+Param[0]
+~~~~~~~~
+
+0=extract from extension & user data, 1=extract from private packets
+
+Result[0]
+~~~~~~~~~
+
+VBI table location
+
+Result[1]
+~~~~~~~~~
+
+VBI table size
+
+
+
+CX2341X_DEC_SET_DECODER_SOURCE
+------------------------------
+
+Enum: 26/0x1A
+
+Description
+~~~~~~~~~~~
+
+Selects decoder source. Ensure that the parameters passed to this
+API match the encoder settings.
+
+Param[0]
+~~~~~~~~
+
+Mode: 0=MPEG from host, 1=YUV from encoder, 2=YUV from host
+
+Param[1]
+~~~~~~~~
+
+YUV picture width
+
+Param[2]
+~~~~~~~~
+
+YUV picture height
+
+Param[3]
+~~~~~~~~
+
+Bitmap: see Param[0] of API 0xBD
+
+
+
+CX2341X_DEC_SET_PREBUFFERING
+----------------------------
+
+Enum: 30/0x1E
+
+Description
+~~~~~~~~~~~
+
+Decoder prebuffering, when enabled up to 128KB are buffered for
+streams <8mpbs or 640KB for streams >8mbps
+
+Param[0]
+~~~~~~~~
+
+0=off, 1=on
diff --git a/Documentation/media/v4l-drivers/index.rst b/Documentation/media/v4l-drivers/index.rst
index 53bc53c948ab..34990b536d39 100644
--- a/Documentation/media/v4l-drivers/index.rst
+++ b/Documentation/media/v4l-drivers/index.rst
@@ -27,6 +27,7 @@ License".
cafe_ccic
cpia2
cx18
+ cx2341x
cx88
davinci-vpbe
fimc
diff --git a/Documentation/video4linux/cx2341x/fw-decoder-api.txt b/Documentation/video4linux/cx2341x/fw-decoder-api.txt
deleted file mode 100644
index 8c317b7a4fc9..000000000000
--- a/Documentation/video4linux/cx2341x/fw-decoder-api.txt
+++ /dev/null
@@ -1,297 +0,0 @@
-Decoder firmware API description
-================================
-
-Note: this API is part of the decoder firmware, so it's cx23415 only.
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_PING_FW
-Enum 0/0x00
-Description
- This API call does nothing. It may be used to check if the firmware
- is responding.
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_START_PLAYBACK
-Enum 1/0x01
-Description
- Begin or resume playback.
-Param[0]
- 0 based frame number in GOP to begin playback from.
-Param[1]
- Specifies the number of muted audio frames to play before normal
- audio resumes. (This is not implemented in the firmware, leave at 0)
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_STOP_PLAYBACK
-Enum 2/0x02
-Description
- Ends playback and clears all decoder buffers. If PTS is not zero,
- playback stops at specified PTS.
-Param[0]
- Display 0=last frame, 1=black
- Note: this takes effect immediately, so if you want to wait for a PTS,
- then use '0', otherwise the screen goes to black at once.
- You can call this later (even if there is no playback) with a 1 value
- to set the screen to black.
-Param[1]
- PTS low
-Param[2]
- PTS high
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_PLAYBACK_SPEED
-Enum 3/0x03
-Description
- Playback stream at speed other than normal. There are two modes of
- operation:
- Smooth: host transfers entire stream and firmware drops unused
- frames.
- Coarse: host drops frames based on indexing as required to achieve
- desired speed.
-Param[0]
- Bitmap:
- 0:7 0 normal
- 1 fast only "1.5 times"
- n nX fast, 1/nX slow
- 30 Framedrop:
- '0' during 1.5 times play, every other B frame is dropped
- '1' during 1.5 times play, stream is unchanged (bitrate
- must not exceed 8mbps)
- 31 Speed:
- '0' slow
- '1' fast
- Note: n is limited to 2. Anything higher does not result in
- faster playback. Instead the host should start dropping frames.
-Param[1]
- Direction: 0=forward, 1=reverse
- Note: to make reverse playback work you have to write full GOPs in
- reverse order.
-Param[2]
- Picture mask:
- 1=I frames
- 3=I, P frames
- 7=I, P, B frames
-Param[3]
- B frames per GOP (for reverse play only)
- Note: for reverse playback the Picture Mask should be set to I or I, P.
- Adding B frames to the mask will result in corrupt video. This field
- has to be set to the correct value in order to keep the timing correct.
-Param[4]
- Mute audio: 0=disable, 1=enable
-Param[5]
- Display 0=frame, 1=field
-Param[6]
- Specifies the number of muted audio frames to play before normal audio
- resumes. (Not implemented in the firmware, leave at 0)
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_STEP_VIDEO
-Enum 5/0x05
-Description
- Each call to this API steps the playback to the next unit defined below
- in the current playback direction.
-Param[0]
- 0=frame, 1=top field, 2=bottom field
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_DMA_BLOCK_SIZE
-Enum 8/0x08
-Description
- Set DMA transfer block size. Counterpart to API 0xC9
-Param[0]
- DMA transfer block size in bytes. A different size may be specified
- when issuing the DMA transfer command.
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_GET_XFER_INFO
-Enum 9/0x09
-Description
- This API call may be used to detect an end of stream condition.
-Result[0]
- Stream type
-Result[1]
- Address offset
-Result[2]
- Maximum bytes to transfer
-Result[3]
- Buffer fullness
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_GET_DMA_STATUS
-Enum 10/0x0A
-Description
- Status of the last DMA transfer
-Result[0]
- Bit 1 set means transfer complete
- Bit 2 set means DMA error
- Bit 3 set means linked list error
-Result[1]
- DMA type: 0=MPEG, 1=OSD, 2=YUV
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SCHED_DMA_FROM_HOST
-Enum 11/0x0B
-Description
- Setup DMA from host operation. Counterpart to API 0xCC
-Param[0]
- Memory address of link list
-Param[1]
- Total # of bytes to transfer
-Param[2]
- DMA type (0=MPEG, 1=OSD, 2=YUV)
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_PAUSE_PLAYBACK
-Enum 13/0x0D
-Description
- Freeze playback immediately. In this mode, when internal buffers are
- full, no more data will be accepted and data request IRQs will be
- masked.
-Param[0]
- Display: 0=last frame, 1=black
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_HALT_FW
-Enum 14/0x0E
-Description
- The firmware is halted and no further API calls are serviced until
- the firmware is uploaded again.
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_STANDARD
-Enum 16/0x10
-Description
- Selects display standard
-Param[0]
- 0=NTSC, 1=PAL
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_GET_VERSION
-Enum 17/0x11
-Description
- Returns decoder firmware version information
-Result[0]
- Version bitmask:
- Bits 0:15 build
- Bits 16:23 minor
- Bits 24:31 major
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_STREAM_INPUT
-Enum 20/0x14
-Description
- Select decoder stream input port
-Param[0]
- 0=memory (default), 1=streaming
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_GET_TIMING_INFO
-Enum 21/0x15
-Description
- Returns timing information from start of playback
-Result[0]
- Frame count by decode order
-Result[1]
- Video PTS bits 0:31 by display order
-Result[2]
- Video PTS bit 32 by display order
-Result[3]
- SCR bits 0:31 by display order
-Result[4]
- SCR bit 32 by display order
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_AUDIO_MODE
-Enum 22/0x16
-Description
- Select audio mode
-Param[0]
- Dual mono mode action
- 0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged
-Param[1]
- Stereo mode action:
- 0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_EVENT_NOTIFICATION
-Enum 23/0x17
-Description
- Setup firmware to notify the host about a particular event.
- Counterpart to API 0xD5
-Param[0]
- Event: 0=Audio mode change between mono, (joint) stereo and dual channel.
- Event: 3=Decoder started
- Event: 4=Unknown: goes off 10-15 times per second while decoding.
- Event: 5=Some sync event: goes off once per frame.
-Param[1]
- Notification 0=disabled, 1=enabled
-Param[2]
- Interrupt bit
-Param[3]
- Mailbox slot, -1 if no mailbox required.
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_DISPLAY_BUFFERS
-Enum 24/0x18
-Description
- Number of display buffers. To decode all frames in reverse playback you
- must use nine buffers.
-Param[0]
- 0=six buffers, 1=nine buffers
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_EXTRACT_VBI
-Enum 25/0x19
-Description
- Extracts VBI data
-Param[0]
- 0=extract from extension & user data, 1=extract from private packets
-Result[0]
- VBI table location
-Result[1]
- VBI table size
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_DECODER_SOURCE
-Enum 26/0x1A
-Description
- Selects decoder source. Ensure that the parameters passed to this
- API match the encoder settings.
-Param[0]
- Mode: 0=MPEG from host, 1=YUV from encoder, 2=YUV from host
-Param[1]
- YUV picture width
-Param[2]
- YUV picture height
-Param[3]
- Bitmap: see Param[0] of API 0xBD
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_PREBUFFERING
-Enum 30/0x1E
-Description
- Decoder prebuffering, when enabled up to 128KB are buffered for
- streams <8mpbs or 640KB for streams >8mbps
-Param[0]
- 0=off, 1=on
--
2.7.4
next prev parent reply other threads:[~2016-07-18 18:30 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-07-18 18:30 [PATCH 00/18] Complete moving media documentation to ReST format Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 01/18] [media] doc-rst: move bttv documentation to bttv.rst file Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 02/18] [media] doc-rst: add documentation for bttv driver Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 03/18] [media] doc-rst: add documentation for tuners Mauro Carvalho Chehab
2016-07-18 18:30 ` Mauro Carvalho Chehab [this message]
2016-07-18 18:30 ` [PATCH 05/18] [media] cx2341x.rst: add fw-decoder-registers.txt content Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 06/18] [media] cx2341x.rst: Add the contents of fw-encoder-api.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 07/18] [media] cx2341x.rst: add the contents of fw-calling.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 08/18] [media] cx2341x.rst: add contents of fw-dma.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 09/18] [media] cx2341x.rst: add contents of fw-memory.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 10/18] [media] cx2341x.rst: add the contents of fw-upload.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 11/18] [media] cx2341x.rst: add contents of fw-osd-api.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 12/18] [media] cx2341x: add contents of README.hm12 Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 13/18] [media] cx2341x.rst: add contents of README.vbi Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 14/18] [media] cx88.rst: add contents from not-in-cx2388x-datasheet.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 15/18] [media] cx88.rst: add contents of hauppauge-wintv-cx88-ir.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 16/18] [media] get rid of Documentation/video4linux/lifeview.txt Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 17/18] [media] doc-rst: fix media kAPI documentation Mauro Carvalho Chehab
2016-07-18 18:30 ` [PATCH 18/18] [media] doc-rst: better name the media books Mauro Carvalho Chehab
2016-07-19 9:19 ` [PATCH 00/18] Complete moving media documentation to ReST format Hans Verkuil
2016-07-19 11:12 ` Mauro Carvalho Chehab
2016-07-19 12:31 ` Markus Heiser
2016-07-19 14:53 ` Mauro Carvalho Chehab
2016-07-19 15:40 ` Mauro Carvalho Chehab
2016-07-19 16:42 ` Markus Heiser
2016-07-19 17:18 ` Mauro Carvalho Chehab
2016-07-21 15:17 ` Markus Heiser
2016-07-22 9:46 ` Mauro Carvalho Chehab
2016-07-22 10:55 ` Markus Heiser
2016-07-19 22:49 ` Jonathan Corbet
2016-07-20 0:00 ` Mauro Carvalho Chehab
2016-07-20 6:07 ` Markus Heiser
2016-07-20 10:19 ` Mauro Carvalho Chehab
2016-07-20 23:28 ` Jonathan Corbet
2016-07-21 14:41 ` Markus Heiser
2016-07-21 16:59 ` Jonathan Corbet
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=a785ddb8686e5bf07624e23790acf08e1beddd7a.1468865380.git.mchehab@s-opensource.com \
--to=mchehab@s-opensource.com \
--cc=corbet@lwn.net \
--cc=linux-doc@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.