[regression,bisected] restore of disks after suspend-to-disk broken in 3.9.x

* [regression,bisected] restore of disks after suspend-to-disk broken in 3.9.x
@ 2013-05-26 13:51 Giacomo Perale
  2013-05-27  5:07 ` Zhang Rui
  0 siblings, 1 reply; 16+ messages in thread
From: Giacomo Perale @ 2013-05-26 13:51 UTC (permalink / raw)
  To: rui.zhang; +Cc: linux-acpi, linux-pm

[-- Attachment #1: Type: text/plain, Size: 5696 bytes --]

Hello,

after upgrading from 3.8.7 to 3.9.x I noticed some slightly longer
delays when resuming from suspend-to-disk and a few new error messages
in the logs:

ata1: link is slow to respond, please be patient (ready=0)
ata3: link is slow to respond, please be patient (ready=0)
ata1: SRST failed (errno=-16)
ata3: SRST failed (errno=-16)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ACPI cmd ef/03:46:00:00:00:a0 (SET FEATURES) filtered out
ata1.00: configured for UDMA/133
sd 0:0:0:0: [sda] Starting disk
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ACPI cmd ef/03:46:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: configured for UDMA/133
sd 2:0:0:0: [sdc] Starting disk
PM: restore of devices complete after 11448.044 msecs

(compared to ~2900 msecs with 3.8.x).

I didn't mind the messages since things were working anyway, but
lately in a couple of cases some disks were dropped and disabled, with
the obvious consequences for the functionality of the system:

ata2: link is slow to respond, please be patient (ready=0)
ata2: SRST failed (errno=-16)
ata2: link is slow to respond, please be patient (ready=0)
ata2: SRST failed (errno=-16)
ata2: link is slow to respond, please be patient (ready=0)
ata2: SRST failed (errno=-16)
ata2: limiting SATA link speed to 1.5 Gbps
ata2: SRST failed (errno=-16)
ata2: reset failed, giving up
ata2.00: disabled
sd 1:0:0:0: [sdb] Starting disk
sd 1:0:0:0: [sdb] START_STOP FAILED
sd 1:0:0:0: [sdb]
Result: hostbyte=0x04 driverbyte=0x00
dpm_run_callback(): scsi_bus_restore+0x0/0x20 returns 262144
PM: Device 1:0:0:0 failed to restore async: error 262144
PM: restore of devices complete after 61130.778 msecs
...
sd 1:0:0:0: [sdb] Unhandled error code
sd 1:0:0:0: [sdb]
Result: hostbyte=0x04 driverbyte=0x00
sd 1:0:0:0: [sdb] CDB:
cdb[0]=0x28: 28 00 00 00 00 6f 00 00 08 00
end_request: I/O error, dev sdb, sector 111
XFS (sdb1): metadata I/O error: block 0x30 ("xfs_trans_read_buf_map")
error 5 numblks 8
ffff88006f710000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
................
XFS (sdb1): Internal error xfs_dir2_leaf_verify at line 62 of file
fs/xfs/xfs_dir2_leaf.c.  Caller 0xffffffff811d17d8

Not having connected the issue with the previous error messages I
initially blamed the disk and replaced it with a new one thinking it
was broken, but the problem persisted so I started a bisection run
that pointed to this commit:

b8bb6cb999858043489c1ddef08eed2127559169 is the first bad commit
commit b8bb6cb999858043489c1ddef08eed2127559169
Author: Zhang Rui <rui.zhang@intel.com>
Date:   Thu Nov 22 15:45:02 2012 +0800

    step_wise: Unify the code for both throttle and dethrottle

    Signed-off-by: Zhang Rui <rui.zhang@intel.com>

:040000 040000 8d313c2dd1dacca2dd01128cf48bb9804e95f258
62bf2c47f021832f423172db87f9e367a91460f2 M    drivers

git bisect start
# bad: [c1be5a5b1b355d40e6cf79cc979eb66dafa24ad1] Linux 3.9
git bisect bad c1be5a5b1b355d40e6cf79cc979eb66dafa24ad1
# good: [19f949f52599ba7c3f67a5897ac6be14bfcb1200] Linux 3.8
git bisect good 19f949f52599ba7c3f67a5897ac6be14bfcb1200
# good: [d778df51c09264076fe0208c099ef7d428f21790] mm: vmscan: save
work scanning (almost) empty LRU lists
git bisect good d778df51c09264076fe0208c099ef7d428f21790
# good: [ee89f81252179dcbf6cd65bd48299f5e52292d88] Merge branch
'for-3.9/core' of git://git.kernel.dk/linux-block
git bisect good ee89f81252179dcbf6cd65bd48299f5e52292d88
# bad: [fa4a6732a8e6153435941cb730d7d54c8367fe72] Merge branch
'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
git bisect bad fa4a6732a8e6153435941cb730d7d54c8367fe72
# bad: [37cae6ad4c484030fa972241533c32730ec79b7d] Merge tag
'dm-3.9-changes' of
git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
git bisect bad 37cae6ad4c484030fa972241533c32730ec79b7d
# bad: [1a32c58bb945970e56f27a1cfb61625a3ac0b88e] Merge tag
'late-mvebu-rebased' of
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
git bisect bad 1a32c58bb945970e56f27a1cfb61625a3ac0b88e
# good: [b6669737d3db7df79fad07180837c23dbe581db5] Merge branch
'for-3.9' of git://linux-nfs.org/~bfields/linux
git bisect good b6669737d3db7df79fad07180837c23dbe581db5
# bad: [7307c00f335a4e986586b12334696098d2fc2bcd] Merge tag
'late-omap' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
git bisect bad 7307c00f335a4e986586b12334696098d2fc2bcd
# bad: [f8f466c81795a3ed2b8a74c8feebc280aec3db81] Merge tag 'late-dt'
of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
git bisect bad f8f466c81795a3ed2b8a74c8feebc280aec3db81
# bad: [4f0a6847815837b63b05fc23878ba391701d8f6a] Thermal: exynos: Add
support for temperature falling interrupt.
git bisect bad 4f0a6847815837b63b05fc23878ba391701d8f6a
# bad: [d6d71ee4a14ae602db343ec48c491851d7ec5267] PM: Introduce Intel
PowerClamp Driver
git bisect bad d6d71ee4a14ae602db343ec48c491851d7ec5267
# bad: [c313637641c3e33388903e16cfde97b2e67adb9e] thermal: db8500: Use
of_match_ptr() macro in db8500_thermal.c
git bisect bad c313637641c3e33388903e16cfde97b2e67adb9e
# bad: [bbf63be4f331358173da26b888a10583fcc92ec0] Thermal: exynos: Add
sysfs node supporting exynos's emulation mode.
git bisect bad bbf63be4f331358173da26b888a10583fcc92ec0
# good: [3dbfff3dfe6714aeefb615c65bec0800dc5a4c51] Introduce
THERMAL_TREND_RAISE/DROP_FULL support for step_wise governor
git bisect good 3dbfff3dfe6714aeefb615c65bec0800dc5a4c51
# bad: [b8bb6cb999858043489c1ddef08eed2127559169] step_wise: Unify the
code for both throttle and dethrottle
git bisect bad b8bb6cb999858043489c1ddef08eed2127559169

Reverting it fixed the problem, as far as I can see. Any idea of what
could be going wrong here?

Thank you,

Giacomo Perale

[-- Attachment #2: dmesg.3.9.0 --]
[-- Type: application/octet-stream, Size: 54846 bytes --]

[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.9.2-gentoo (giacomo@KazeNoTani) (gcc version 4.6.3 (Gentoo 4.6.3 p1.13, pie-0.5.2) ) #3 SMP PREEMPT Sat May 25 23:47:57 CEST 2013
[    0.000000] Command line: root=/dev/sda2 hpet=force
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f3ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009f400-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007ffeffff] usable
[    0.000000] BIOS-e820: [mem 0x000000007fff0000-0x000000007fff2fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000007fff3000-0x000000007fffffff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.2 present.
[    0.000000] DMI: Unknow Unknow/KN9 Series(NF-CK804), BIOS 6.00 PG 04/28/2008
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] No AGP bridge found
[    0.000000] e820: last_pfn = 0x7fff0 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-C7FFF write-protect
[    0.000000]   C8000-FFFFF uncachable
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 0000000000 mask FF80000000 write-back
[    0.000000]   1 disabled
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x019f0000, 0x019f0fff] PGTABLE
[    0.000000] BRK [0x019f1000, 0x019f1fff] PGTABLE
[    0.000000] BRK [0x019f2000, 0x019f2fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x7fc00000-0x7fdfffff]
[    0.000000]  [mem 0x7fc00000-0x7fdfffff] page 2M
[    0.000000] BRK [0x019f3000, 0x019f3fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x7c000000-0x7fbfffff]
[    0.000000]  [mem 0x7c000000-0x7fbfffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0x7bffffff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x7bffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x7fe00000-0x7ffeffff]
[    0.000000]  [mem 0x7fe00000-0x7ffeffff] page 4k
[    0.000000] BRK [0x019f4000, 0x019f4fff] PGTABLE
[    0.000000] ACPI: RSDP 00000000000f7e00 00014 (v00 Nvidia)
[    0.000000] ACPI: RSDT 000000007fff3040 00034 (v01 Nvidia AWRDACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: FACP 000000007fff30c0 00074 (v01 Nvidia AWRDACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: DSDT 000000007fff3180 06422 (v01 NVIDIA AWRDACPI 00001000 MSFT 0100000E)
[    0.000000] ACPI: FACS 000000007fff0000 00040
[    0.000000] ACPI: SSDT 000000007fff96c0 0028A (v01 PTLTD  POWERNOW 00000001  LTP 00000001)
[    0.000000] ACPI: MCFG 000000007fff99c0 0003C (v01 Nvidia AWRDACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: APIC 000000007fff9600 00072 (v01 Nvidia AWRDACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000]  [ffffea0000000000-ffffea0001ffffff] PMD -> [ffff88007d600000-ffff88007f5fffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009efff]
[    0.000000]   node   0: [mem 0x00100000-0x7ffeffff]
[    0.000000] On node 0 totalpages: 524174
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 8128 pages used for memmap
[    0.000000]   DMA32 zone: 520176 pages, LIFO batch:31
[    0.000000] Nvidia board detected. Ignoring ACPI timer override.
[    0.000000] If you got timer trouble try acpi_use_timer_override
[    0.000000] Detected use of extended apic ids on hypertransport bus
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] ACPI: IRQ14 used by override.
[    0.000000] ACPI: IRQ15 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[    0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[    0.000000] e820: [mem 0x80000000-0xdfffffff] available for PCI devices
[    0.000000] setup_percpu: NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:2 nr_node_ids:1
[    0.000000] PERCPU: Embedded 27 pages/cpu @ffff88007fc00000 s79232 r8192 d23168 u1048576
[    0.000000] pcpu-alloc: s79232 r8192 d23168 u1048576 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 515961
[    0.000000] Kernel command line: root=/dev/sda2 hpet=force
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Node 0: aperture @ 1010000000 size 32 MB
[    0.000000] Aperture beyond 4GB. Ignoring.
[    0.000000] Memory: 2050256k/2097088k available (4280k kernel code, 392k absent, 46440k reserved, 4396k data, 756k init)
[    0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] NR_IRQS:4352 nr_irqs:512 16
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 2499.974 MHz processor
[    0.000000] tsc: Marking TSC unstable due to TSCs unsynchronized
[    0.002027] Calibrating delay loop (skipped), value calculated using timer frequency.. 4999.94 BogoMIPS (lpj=2499974)
[    0.002077] pid_max: default: 32768 minimum: 301
[    0.003034] Mount-cache hash table entries: 256
[    0.003261] Initializing cgroup subsys devices
[    0.003287] Initializing cgroup subsys freezer
[    0.003331] tseg: 0000000000
[    0.003338] CPU: Physical Processor ID: 0
[    0.003361] CPU: Processor Core ID: 0
[    0.003385] mce: CPU supports 5 MCE banks
[    0.003416] LVT offset 0 assigned for vector 0xf9
[    0.003442] process: using AMD E400 aware idle routine
[    0.003467] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 4
Last level dTLB entries: 4KB 512, 2MB 8, 4MB 4
tlb_flushall_shift: 4
[    0.003562] Freeing SMP alternatives: 16k freed
[    0.003595] ACPI: Core revision 20130117
[    0.005849] ACPI: All ACPI Tables successfully acquired
[    0.006423] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
[    0.017104] smpboot: CPU0: AMD Athlon(tm) Dual Core Processor 4850e (fam: 0f, model: 6b, stepping: 02)
[    0.018000] Performance Events: AMD PMU driver.
[    0.018000] ... version:                0
[    0.018000] ... bit width:              48
[    0.018000] ... generic registers:      4
[    0.018000] ... value mask:             0000ffffffffffff
[    0.018000] ... max period:             00007fffffffffff
[    0.018000] ... fixed-purpose events:   0
[    0.018000] ... event mask:             000000000000000f
[    0.027069] smpboot: Booting Node   0, Processors  #1 OK
[    0.098085] Brought up 2 CPUs
[    0.098110] smpboot: Total of 2 processors activated (9999.23 BogoMIPS)
[    0.098590] devtmpfs: initialized
[    0.098590] PM: Registering ACPI NVS region [mem 0x7fff0000-0x7fff2fff] (12288 bytes)
[    0.099158] NET: Registered protocol family 16
[    0.099264] node 0 link 0: io port [7000, ffff]
[    0.099267] TOM: 0000000080000000 aka 2048M
[    0.099291] node 0 link 0: mmio [a0000, bffff]
[    0.099293] node 0 link 0: mmio [feb00000, fec0ffff]
[    0.099295] node 0 link 0: mmio [80000000, dfffffff]
[    0.099296] node 0 link 0: mmio [f0000000, fe02ffff]
[    0.099298] node 0 link 0: mmio [e0000000, e05fffff]
[    0.099300] bus: [bus 00-05] on node 0 link 0
[    0.099302] bus: 00 [io  0x0000-0xffff]
[    0.099303] bus: 00 [mem 0x000a0000-0x000bffff]
[    0.099304] bus: 00 [mem 0xfe030000-0xfcffffffff]
[    0.099304] bus: 00 [mem 0x80000000-0xefffffff]
[    0.099305] bus: 00 [mem 0xf0000000-0xfe02ffff]
[    0.099314] ACPI: bus type PCI registered
[    0.099371] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.099400] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.108006] PCI: Using configuration type 1 for base access
[    0.108507] bio: create slab <bio-0> at 0
[    0.108507] ACPI: Added _OSI(Module Device)
[    0.108507] ACPI: Added _OSI(Processor Device)
[    0.108507] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.108507] ACPI: Added _OSI(Processor Aggregator Device)
[    0.109573] ACPI: EC: Look up EC in DSDT
[    0.112269] ACPI: Interpreter enabled
[    0.112300] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130117/hwxface-568)
[    0.112370] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130117/hwxface-568)
[    0.112445] ACPI: (supports S0 S3 S4 S5)
[    0.112469] ACPI: Using IOAPIC for interrupt routing
[    0.112516] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.117820] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-05])
[    0.118668] PCI host bridge to bus 0000:00
[    0.118695] pci_bus 0000:00: root bus resource [bus 00-05]
[    0.118720] pci_bus 0000:00: root bus resource [io  0x0000-0x03af]
[    0.118745] pci_bus 0000:00: root bus resource [io  0x03e0-0x0cf7]
[    0.118770] pci_bus 0000:00: root bus resource [io  0x7000-0xffff]
[    0.118795] pci_bus 0000:00: root bus resource [io  0x03b0-0x03df]
[    0.118820] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.118846] pci_bus 0000:00: root bus resource [mem 0x80000000-0xdfffffff]
[    0.118871] pci_bus 0000:00: root bus resource [mem 0xf0000000-0xfe02ffff]
[    0.118896] pci_bus 0000:00: root bus resource [mem 0xfeb00000-0xfebfffff]
[    0.118922] pci_bus 0000:00: root bus resource [io  0x1c00-0x1c80]
[    0.118957] pci 0000:00:00.0: [10de:005e] type 00 class 0x058000
[    0.119117] pci 0000:00:01.0: [10de:0050] type 00 class 0x060100
[    0.119136] pci 0000:00:01.0: Force enabled HPET at 0xfed00000
[    0.119183] pci 0000:00:01.1: [10de:0052] type 00 class 0x0c0500
[    0.119190] pci 0000:00:01.1: reg 10: [io  0xfc00-0xfc1f]
[    0.119200] pci 0000:00:01.1: reg 20: [io  0x1c00-0x1c3f]
[    0.119203] pci 0000:00:01.1: reg 24: [io  0x1c40-0x1c7f]
[    0.119216] pci 0000:00:01.1: PME# supported from D3hot D3cold
[    0.119272] pci 0000:00:02.0: [10de:005a] type 00 class 0x0c0310
[    0.119278] pci 0000:00:02.0: reg 10: [mem 0xfe02f000-0xfe02ffff]
[    0.119300] pci 0000:00:02.0: supports D1 D2
[    0.119302] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.119331] pci 0000:00:02.0: System wakeup disabled by ACPI
[    0.119387] pci 0000:00:02.1: [10de:005b] type 00 class 0x0c0320
[    0.119394] pci 0000:00:02.1: reg 10: [mem 0xfeb00000-0xfeb000ff]
[    0.119421] pci 0000:00:02.1: supports D1 D2
[    0.119423] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.119461] pci 0000:00:02.1: System wakeup disabled by ACPI
[    0.119522] pci 0000:00:06.0: [10de:0053] type 00 class 0x01018a
[    0.119536] pci 0000:00:06.0: reg 20: [io  0xf000-0xf00f]
[    0.119585] pci 0000:00:07.0: [10de:0054] type 00 class 0x010185
[    0.119591] pci 0000:00:07.0: reg 10: [io  0x09f0-0x09f7]
[    0.119594] pci 0000:00:07.0: reg 14: [io  0x0bf0-0x0bf3]
[    0.119598] pci 0000:00:07.0: reg 18: [io  0x0970-0x0977]
[    0.119601] pci 0000:00:07.0: reg 1c: [io  0x0b70-0x0b73]
[    0.119605] pci 0000:00:07.0: reg 20: [io  0xdc00-0xdc0f]
[    0.119609] pci 0000:00:07.0: reg 24: [mem 0xfe02d000-0xfe02dfff]
[    0.119652] pci 0000:00:08.0: [10de:0055] type 00 class 0x010185
[    0.119658] pci 0000:00:08.0: reg 10: [io  0x09e0-0x09e7]
[    0.119661] pci 0000:00:08.0: reg 14: [io  0x0be0-0x0be3]
[    0.119665] pci 0000:00:08.0: reg 18: [io  0x0960-0x0967]
[    0.119668] pci 0000:00:08.0: reg 1c: [io  0x0b60-0x0b63]
[    0.119672] pci 0000:00:08.0: reg 20: [io  0xc800-0xc80f]
[    0.119676] pci 0000:00:08.0: reg 24: [mem 0xfe02c000-0xfe02cfff]
[    0.119718] pci 0000:00:09.0: [10de:005c] type 01 class 0x060401
[    0.119737] pci 0000:00:09.0: System wakeup disabled by ACPI
[    0.119799] pci 0000:00:0a.0: [10de:0057] type 00 class 0x068000
[    0.119805] pci 0000:00:0a.0: reg 10: [mem 0xfe02b000-0xfe02bfff]
[    0.119809] pci 0000:00:0a.0: reg 14: [io  0xc400-0xc407]
[    0.119829] pci 0000:00:0a.0: supports D1 D2
[    0.119830] pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.119859] pci 0000:00:0a.0: System wakeup disabled by ACPI
[    0.119913] pci 0000:00:0b.0: [10de:005d] type 01 class 0x060400
[    0.119936] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.119965] pci 0000:00:0b.0: System wakeup disabled by ACPI
[    0.120020] pci 0000:00:0c.0: [10de:005d] type 01 class 0x060400
[    0.120043] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.120067] pci 0000:00:0c.0: System wakeup disabled by ACPI
[    0.120120] pci 0000:00:0d.0: [10de:005d] type 01 class 0x060400
[    0.120142] pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.120167] pci 0000:00:0d.0: System wakeup disabled by ACPI
[    0.120221] pci 0000:00:0e.0: [10de:005d] type 01 class 0x060400
[    0.120243] pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.120264] pci 0000:00:0e.0: System wakeup disabled by ACPI
[    0.120323] pci 0000:00:18.0: [1022:1100] type 00 class 0x060000
[    0.120364] pci 0000:00:18.1: [1022:1101] type 00 class 0x060000
[    0.120405] pci 0000:00:18.2: [1022:1102] type 00 class 0x060000
[    0.120448] pci 0000:00:18.3: [1022:1103] type 00 class 0x060000
[    0.120582] pci 0000:01:08.0: [1131:7133] type 00 class 0x048000
[    0.120592] pci 0000:01:08.0: reg 10: [mem 0xfdeff000-0xfdeff7ff]
[    0.120632] pci 0000:01:08.0: supports D1 D2
[    0.120662] pci 0000:01:09.0: [1102:0002] type 00 class 0x040100
[    0.120672] pci 0000:01:09.0: reg 10: [io  0xbc00-0xbc1f]
[    0.120710] pci 0000:01:09.0: supports D1 D2
[    0.120740] pci 0000:01:09.1: [1102:7002] type 00 class 0x098000
[    0.120749] pci 0000:01:09.1: reg 10: [io  0xb800-0xb807]
[    0.120787] pci 0000:01:09.1: supports D1 D2
[    0.120830] pci 0000:00:09.0: PCI bridge to [bus 01] (subtractive decode)
[    0.120857] pci 0000:00:09.0:   bridge window [io  0xb000-0xbfff]
[    0.120859] pci 0000:00:09.0:   bridge window [mem 0xfde00000-0xfdefffff]
[    0.120861] pci 0000:00:09.0:   bridge window [mem 0xfdf00000-0xfdffffff pref]
[    0.120864] pci 0000:00:09.0:   bridge window [io  0x0000-0x03af] (subtractive decode)
[    0.120865] pci 0000:00:09.0:   bridge window [io  0x03e0-0x0cf7] (subtractive decode)
[    0.120867] pci 0000:00:09.0:   bridge window [io  0x7000-0xffff] (subtractive decode)
[    0.120869] pci 0000:00:09.0:   bridge window [io  0x03b0-0x03df] (subtractive decode)
[    0.120871] pci 0000:00:09.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.120873] pci 0000:00:09.0:   bridge window [mem 0x80000000-0xdfffffff] (subtractive decode)
[    0.120874] pci 0000:00:09.0:   bridge window [mem 0xf0000000-0xfe02ffff] (subtractive decode)
[    0.120876] pci 0000:00:09.0:   bridge window [mem 0xfeb00000-0xfebfffff] (subtractive decode)
[    0.120878] pci 0000:00:09.0:   bridge window [io  0x1c00-0x1c80] (subtractive decode)
[    0.120905] pci 0000:00:0b.0: PCI bridge to [bus 02]
[    0.120931] pci 0000:00:0b.0:   bridge window [io  0xa000-0xafff]
[    0.120933] pci 0000:00:0b.0:   bridge window [mem 0xfdd00000-0xfddfffff]
[    0.120936] pci 0000:00:0b.0:   bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref]
[    0.120961] pci 0000:00:0c.0: PCI bridge to [bus 03]
[    0.120988] pci 0000:00:0c.0:   bridge window [io  0x9000-0x9fff]
[    0.120990] pci 0000:00:0c.0:   bridge window [mem 0xfdb00000-0xfdbfffff]
[    0.120993] pci 0000:00:0c.0:   bridge window [mem 0xfda00000-0xfdafffff 64bit pref]
[    0.121024] pci 0000:00:0d.0: PCI bridge to [bus 04]
[    0.121050] pci 0000:00:0d.0:   bridge window [io  0x8000-0x8fff]
[    0.121052] pci 0000:00:0d.0:   bridge window [mem 0xfd900000-0xfd9fffff]
[    0.121055] pci 0000:00:0d.0:   bridge window [mem 0xfd800000-0xfd8fffff 64bit pref]
[    0.121085] pci 0000:05:00.0: [1002:5b63] type 00 class 0x030000
[    0.121093] pci 0000:05:00.0: reg 10: [mem 0xd0000000-0xdfffffff pref]
[    0.121099] pci 0000:05:00.0: reg 14: [io  0x7c00-0x7cff]
[    0.121104] pci 0000:05:00.0: reg 18: [mem 0xfd7f0000-0xfd7fffff]
[    0.121121] pci 0000:05:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[    0.121143] pci 0000:05:00.0: supports D1 D2
[    0.121178] pci 0000:05:00.1: [1002:5b73] type 00 class 0x038000
[    0.121185] pci 0000:05:00.1: reg 10: [mem 0xfd7e0000-0xfd7effff]
[    0.121225] pci 0000:05:00.1: supports D1 D2
[    0.121255] pci 0000:05:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.121290] pci 0000:00:0e.0: PCI bridge to [bus 05]
[    0.121316] pci 0000:00:0e.0:   bridge window [io  0x7000-0x7fff]
[    0.121318] pci 0000:00:0e.0:   bridge window [mem 0xfd700000-0xfd7fffff]
[    0.121321] pci 0000:00:0e.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.121329] pci_bus 0000:00: on NUMA node 0
[    0.121334] acpi PNP0A08:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[    0.121360] acpi PNP0A08:00: Unable to request _OSC control (_OSC support mask: 0x08)
[    0.121541] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 *10 11)
[    0.121703] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 10 *11)
[    0.121864] ACPI: PCI Interrupt Link [LNK3] (IRQs *5 10 11)
[    0.122026] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 10 11) *0, disabled.
[    0.122224] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 10 11) *0, disabled.
[    0.122424] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 *10 11)
[    0.122583] ACPI: PCI Interrupt Link [LUBB] (IRQs 5 10 11) *0, disabled.
[    0.122783] ACPI: PCI Interrupt Link [LMAC] (IRQs *5 10 11)
[    0.122942] ACPI: PCI Interrupt Link [LACI] (IRQs 5 10 11) *0, disabled.
[    0.123139] ACPI: PCI Interrupt Link [LMCI] (IRQs 5 10 11) *0, disabled.
[    0.123338] ACPI: PCI Interrupt Link [LSMB] (IRQs *5 10 11)
[    0.123504] ACPI: PCI Interrupt Link [LUB2] (IRQs 5 10 *11)
[    0.123663] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 10 11) *0, disabled.
[    0.123867] ACPI: PCI Interrupt Link [LSID] (IRQs 5 *10 11)
[    0.124040] ACPI: PCI Interrupt Link [LFID] (IRQs 5 10 *11)
[    0.124207] ACPI: PCI Interrupt Link [LPCA] (IRQs 5 10 11) *0, disabled.
[    0.124423] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0
[    0.124577] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0
[    0.124733] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0
[    0.124886] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
[    0.125033] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
[    0.125192] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
[    0.125408] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
[    0.125642] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
[    0.125858] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
[    0.126098] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
[    0.126332] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
[    0.127055] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
[    0.127271] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
[    0.127509] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
[    0.127728] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
[    0.128006] ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
[    0.128628] ACPI: Enabled 1 GPEs in block 00 to 1F
[    0.128697] acpi root: \_SB_.PCI0 notify handler is installed
[    0.128733] Found 1 acpi root devices
[    0.128813] vgaarb: device added: PCI:0000:05:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.128813] vgaarb: loaded
[    0.128813] vgaarb: bridge control possible 0000:05:00.0
[    0.128813] SCSI subsystem initialized
[    0.129003] ACPI: bus type ATA registered
[    0.129036] libata version 3.00 loaded.
[    0.129053] PCI: Using ACPI for IRQ routing
[    0.133991] PCI: pci_cache_line_size set to 64 bytes
[    0.134034] e820: reserve RAM buffer [mem 0x0009f400-0x0009ffff]
[    0.134036] e820: reserve RAM buffer [mem 0x7fff0000-0x7fffffff]
[    0.134237] hpet clockevent registered
[    0.134239] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.134268] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[    0.134371] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[    0.140023] Switching to clocksource hpet
[    0.145365] pnp: PnP ACPI init
[    0.145401] ACPI: bus type PNP registered
[    0.145560] system 00:00: [io  0x1000-0x107f] has been reserved
[    0.145586] system 00:00: [io  0x1080-0x10ff] has been reserved
[    0.145611] system 00:00: [io  0x1400-0x147f] has been reserved
[    0.145637] system 00:00: [io  0x1480-0x14ff] has been reserved
[    0.145662] system 00:00: [io  0x1800-0x187f] has been reserved
[    0.145688] system 00:00: [io  0x1880-0x18ff] has been reserved
[    0.145715] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.146205] system 00:01: [io  0x0b78-0x0b7b] has been reserved
[    0.146231] system 00:01: [io  0x0f78-0x0f7b] has been reserved
[    0.146257] system 00:01: [io  0x0a78-0x0a7b] has been reserved
[    0.146282] system 00:01: [io  0x0e78-0x0e7b] has been reserved
[    0.146307] system 00:01: [io  0x0bbc-0x0bbf] has been reserved
[    0.146333] system 00:01: [io  0x0fbc-0x0fbf] has been reserved
[    0.146358] system 00:01: [io  0x04d0-0x04d1] has been reserved
[    0.146383] system 00:01: [io  0x0294-0x0297] has been reserved
[    0.146409] system 00:01: [io  0x0295-0x0296] has been reserved
[    0.146434] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.146446] pnp 00:02: [dma 4]
[    0.146470] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.146509] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.146534] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.146566] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.146935] system 00:06: [mem 0xe0000000-0xefffffff] has been reserved
[    0.146961] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.147098] system 00:07: [mem 0x000d0000-0x000d3fff] has been reserved
[    0.147125] system 00:07: [mem 0x000f0000-0x000f7fff] could not be reserved
[    0.147151] system 00:07: [mem 0x000f8000-0x000fbfff] could not be reserved
[    0.147177] system 00:07: [mem 0x000fc000-0x000fffff] could not be reserved
[    0.147202] system 00:07: [mem 0x7fff0000-0x7fffffff] could not be reserved
[    0.147228] system 00:07: [mem 0xffff0000-0xffffffff] has been reserved
[    0.147254] system 00:07: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.147280] system 00:07: [mem 0x00100000-0x7ffeffff] could not be reserved
[    0.147306] system 00:07: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.147332] system 00:07: [mem 0xfee00000-0xfeefffff] has been reserved
[    0.147360] system 00:07: [mem 0xfefff000-0xfeffffff] has been reserved
[    0.147385] system 00:07: [mem 0xfff80000-0xfff80fff] has been reserved
[    0.147411] system 00:07: [mem 0xfff90000-0xfffbffff] has been reserved
[    0.147437] system 00:07: [mem 0xfffed000-0xfffeffff] has been reserved
[    0.147463] system 00:07: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.147471] pnp: PnP ACPI: found 8 devices
[    0.147495] ACPI: bus type PNP unregistered
[    0.152083] pci 0000:00:09.0: PCI bridge to [bus 01]
[    0.152109] pci 0000:00:09.0:   bridge window [io  0xb000-0xbfff]
[    0.152135] pci 0000:00:09.0:   bridge window [mem 0xfde00000-0xfdefffff]
[    0.152161] pci 0000:00:09.0:   bridge window [mem 0xfdf00000-0xfdffffff pref]
[    0.152188] pci 0000:00:0b.0: PCI bridge to [bus 02]
[    0.152213] pci 0000:00:0b.0:   bridge window [io  0xa000-0xafff]
[    0.152238] pci 0000:00:0b.0:   bridge window [mem 0xfdd00000-0xfddfffff]
[    0.152264] pci 0000:00:0b.0:   bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref]
[    0.152291] pci 0000:00:0c.0: PCI bridge to [bus 03]
[    0.152315] pci 0000:00:0c.0:   bridge window [io  0x9000-0x9fff]
[    0.152341] pci 0000:00:0c.0:   bridge window [mem 0xfdb00000-0xfdbfffff]
[    0.152367] pci 0000:00:0c.0:   bridge window [mem 0xfda00000-0xfdafffff 64bit pref]
[    0.152393] pci 0000:00:0d.0: PCI bridge to [bus 04]
[    0.152418] pci 0000:00:0d.0:   bridge window [io  0x8000-0x8fff]
[    0.152444] pci 0000:00:0d.0:   bridge window [mem 0xfd900000-0xfd9fffff]
[    0.152469] pci 0000:00:0d.0:   bridge window [mem 0xfd800000-0xfd8fffff 64bit pref]
[    0.152500] pci 0000:05:00.0: BAR 6: assigned [mem 0xfd700000-0xfd71ffff pref]
[    0.152527] pci 0000:00:0e.0: PCI bridge to [bus 05]
[    0.152551] pci 0000:00:0e.0:   bridge window [io  0x7000-0x7fff]
[    0.152577] pci 0000:00:0e.0:   bridge window [mem 0xfd700000-0xfd7fffff]
[    0.152603] pci 0000:00:0e.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.152635] pci 0000:00:09.0: setting latency timer to 64
[    0.152641] pci_bus 0000:00: resource 4 [io  0x0000-0x03af]
[    0.152643] pci_bus 0000:00: resource 5 [io  0x03e0-0x0cf7]
[    0.152645] pci_bus 0000:00: resource 6 [io  0x7000-0xffff]
[    0.152646] pci_bus 0000:00: resource 7 [io  0x03b0-0x03df]
[    0.152648] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff]
[    0.152650] pci_bus 0000:00: resource 9 [mem 0x80000000-0xdfffffff]
[    0.152651] pci_bus 0000:00: resource 10 [mem 0xf0000000-0xfe02ffff]
[    0.152653] pci_bus 0000:00: resource 11 [mem 0xfeb00000-0xfebfffff]
[    0.152655] pci_bus 0000:00: resource 12 [io  0x1c00-0x1c80]
[    0.152657] pci_bus 0000:01: resource 0 [io  0xb000-0xbfff]
[    0.152658] pci_bus 0000:01: resource 1 [mem 0xfde00000-0xfdefffff]
[    0.152660] pci_bus 0000:01: resource 2 [mem 0xfdf00000-0xfdffffff pref]
[    0.152662] pci_bus 0000:01: resource 4 [io  0x0000-0x03af]
[    0.152663] pci_bus 0000:01: resource 5 [io  0x03e0-0x0cf7]
[    0.152665] pci_bus 0000:01: resource 6 [io  0x7000-0xffff]
[    0.152667] pci_bus 0000:01: resource 7 [io  0x03b0-0x03df]
[    0.152668] pci_bus 0000:01: resource 8 [mem 0x000a0000-0x000bffff]
[    0.152670] pci_bus 0000:01: resource 9 [mem 0x80000000-0xdfffffff]
[    0.152672] pci_bus 0000:01: resource 10 [mem 0xf0000000-0xfe02ffff]
[    0.152673] pci_bus 0000:01: resource 11 [mem 0xfeb00000-0xfebfffff]
[    0.152675] pci_bus 0000:01: resource 12 [io  0x1c00-0x1c80]
[    0.152677] pci_bus 0000:02: resource 0 [io  0xa000-0xafff]
[    0.152678] pci_bus 0000:02: resource 1 [mem 0xfdd00000-0xfddfffff]
[    0.152680] pci_bus 0000:02: resource 2 [mem 0xfdc00000-0xfdcfffff 64bit pref]
[    0.152682] pci_bus 0000:03: resource 0 [io  0x9000-0x9fff]
[    0.152684] pci_bus 0000:03: resource 1 [mem 0xfdb00000-0xfdbfffff]
[    0.152685] pci_bus 0000:03: resource 2 [mem 0xfda00000-0xfdafffff 64bit pref]
[    0.152687] pci_bus 0000:04: resource 0 [io  0x8000-0x8fff]
[    0.152689] pci_bus 0000:04: resource 1 [mem 0xfd900000-0xfd9fffff]
[    0.152691] pci_bus 0000:04: resource 2 [mem 0xfd800000-0xfd8fffff 64bit pref]
[    0.152693] pci_bus 0000:05: resource 0 [io  0x7000-0x7fff]
[    0.152694] pci_bus 0000:05: resource 1 [mem 0xfd700000-0xfd7fffff]
[    0.152696] pci_bus 0000:05: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.152735] NET: Registered protocol family 2
[    0.152909] TCP established hash table entries: 16384 (order: 6, 262144 bytes)
[    0.153063] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[    0.153205] TCP: Hash tables configured (established 16384 bind 16384)
[    0.153304] TCP: reno registered
[    0.153330] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[    0.153373] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[    0.153479] NET: Registered protocol family 1
[    0.153745] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
[    0.216191] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
[    0.216319] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.216347] pci 0000:00:0b.0: Found disabled HT MSI Mapping
[    0.216376] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.216402] pci 0000:00:0b.0: Linking AER extended capability
[    0.216454] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.216482] pci 0000:00:0c.0: Found disabled HT MSI Mapping
[    0.216511] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.216536] pci 0000:00:0c.0: Linking AER extended capability
[    0.216590] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.216617] pci 0000:00:0d.0: Found disabled HT MSI Mapping
[    0.216646] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.216671] pci 0000:00:0d.0: Linking AER extended capability
[    0.216729] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.216756] pci 0000:00:0e.0: Found disabled HT MSI Mapping
[    0.216785] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.216810] pci 0000:00:0e.0: Linking AER extended capability
[    0.216849] pci 0000:05:00.0: Boot video device
[    0.216853] PCI: CLS 64 bytes, default 64
[    0.217293] audit: initializing netlink socket (disabled)
[    0.217329] type=2000 audit(1369519051.217:1): initialized
[    0.219210] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[    0.219521] msgmni has been set to 4004
[    0.219792] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.219820] io scheduler noop registered
[    0.219844] io scheduler deadline registered
[    0.219870] io scheduler cfq registered (default)
[    0.219988] pcieport 0000:00:0b.0: irq 40 for MSI/MSI-X
[    0.220053] pcieport 0000:00:0c.0: irq 41 for MSI/MSI-X
[    0.220092] pcieport 0000:00:0d.0: irq 42 for MSI/MSI-X
[    0.220128] pcieport 0000:00:0e.0: irq 43 for MSI/MSI-X
[    0.220372] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    0.220402] ACPI: Power Button [PWRB]
[    0.220468] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    0.220494] ACPI: Power Button [PWRF]
[    0.220555] ACPI: Fan [FAN] (on)
[    0.222704] thermal LNXTHERM:00: registered as thermal_zone0
[    0.222730] ACPI: Thermal Zone [THRM] (40 C)
[    0.223373] loop: module loaded
[    0.223470] sata_nv 0000:00:07.0: version 3.5
[    0.223656] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
[    0.223734] sata_nv 0000:00:07.0: setting latency timer to 64
[    0.223906] scsi0 : sata_nv
[    0.224079] scsi1 : sata_nv
[    0.224160] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xdc00 irq 21
[    0.224186] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xdc08 irq 21
[    0.224393] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
[    0.224451] sata_nv 0000:00:08.0: setting latency timer to 64
[    0.224602] scsi2 : sata_nv
[    0.224692] scsi3 : sata_nv
[    0.224768] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xc800 irq 20
[    0.224794] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xc808 irq 20
[    0.224861] pata_amd 0000:00:06.0: version 0.4.1
[    0.224902] pata_amd 0000:00:06.0: setting latency timer to 64
[    0.225125] scsi4 : pata_amd
[    0.225334] scsi5 : pata_amd
[    0.225530] ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[    0.225557] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[    0.225661] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    0.228299] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.228346] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.228454] mousedev: PS/2 mouse device common for all mice
[    0.228561] cpuidle: using governor ladder
[    0.228585] cpuidle: using governor menu
[    0.228718] TCP: cubic registered
[    0.228743] NET: Registered protocol family 17
[    0.678019] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    0.679020] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    0.682083] ata1.00: ATA-8: WDC WD3200AAKS-22L6A0, 01.03E01, max UDMA/133
[    0.682110] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    0.682203] ata3.00: ATA-8: WDC WD10EZEX-00RKKA0, 80.00A80, max UDMA/133
[    0.682230] ata3.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    0.686031] ata3.00: configured for UDMA/133
[    0.686088] ata1.00: configured for UDMA/133
[    0.686249] scsi 0:0:0:0: Direct-Access     ATA      WDC WD3200AAKS-2 01.0 PQ: 0 ANSI: 5
[    0.686405] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    0.686420] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    0.686460] sd 0:0:0:0: [sda] Write Protect is off
[    0.686462] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    0.686479] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.690509]  sda: sda1 sda2 sda3 sda4
[    0.690908] sd 0:0:0:0: [sda] Attached SCSI disk
[    0.989012] ata2: SATA link down (SStatus 0 SControl 300)
[    0.989138] scsi 2:0:0:0: Direct-Access     ATA      WDC WD10EZEX-00R 80.0 PQ: 0 ANSI: 5
[    0.989262] sd 2:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[    0.989289] sd 2:0:0:0: [sdb] 4096-byte physical blocks
[    0.989298] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    0.989404] sd 2:0:0:0: [sdb] Write Protect is off
[    0.989431] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    0.989465] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.045952]  sdb: sdb1 sdb2 sdb3 sdb4
[    1.046334] sd 2:0:0:0: [sdb] Attached SCSI disk
[    1.443019] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.446199] ata4.00: ATA-7: WDC WD1600JS-22NCB1, 10.02E02, max UDMA/133
[    1.446225] ata4.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    1.449199] ata4.00: configured for UDMA/133
[    1.449306] scsi 3:0:0:0: Direct-Access     ATA      WDC WD1600JS-22N 10.0 PQ: 0 ANSI: 5
[    1.449430] sd 3:0:0:0: [sdc] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[    1.449448] sd 3:0:0:0: Attached scsi generic sg2 type 0
[    1.449520] sd 3:0:0:0: [sdc] Write Protect is off
[    1.449556] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[    1.449572] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.457321]  sdc: sdc1
[    1.457589] sd 3:0:0:0: [sdc] Attached SCSI disk
[    1.622286] ata6.00: ATAPI: PIONEER DVD-RW  DVR-111D, 1.23, max UDMA/66
[    1.622317] ata6.01: ATAPI: TOSHIBA DVD-ROM SD-M1612, 1806, max UDMA/33
[    1.622348] ata6: nv_mode_filter: 0x1f39f&0x1f39f->0x1f39f, BIOS=0x1f000 (0xc5c0) ACPI=0x1f01f (30:60:0x1f)
[    1.622352] ata6: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc5c0) ACPI=0x701f (30:60:0x1f)
[    1.628214] ata6.00: configured for UDMA/66
[    1.650254] ata6.01: configured for UDMA/33
[    1.663101] scsi 5:0:0:0: CD-ROM            PIONEER  DVD-RW  DVR-111D 1.23 PQ: 0 ANSI: 5
[    1.674287] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[    1.674870] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.674977] sr 5:0:0:0: Attached scsi CD-ROM sr0
[    1.675082] sr 5:0:0:0: Attached scsi generic sg3 type 5
[    1.680771] scsi 5:0:1:0: CD-ROM            TOSHIBA  DVD-ROM SD-M1612 1806 PQ: 0 ANSI: 5
[    1.684389] sr1: scsi3-mmc drive: 40x/48x cd/rw xa/form2 cdda tray
[    1.684507] sr 5:0:1:0: Attached scsi CD-ROM sr1
[    1.684588] sr 5:0:1:0: Attached scsi generic sg4 type 5
[    1.694303] registered taskstats version 1
[    1.719234] XFS (sda2): Mounting Filesystem
[    1.908953] XFS (sda2): Ending clean mount
[    1.908991] VFS: Mounted root (xfs filesystem) readonly on device 8:2.
[    1.944664] devtmpfs: mounted
[    1.945342] Freeing unused kernel memory: 756k freed
[    1.945724] Write protecting the kernel read-only data: 8192k
[    1.950130] Freeing unused kernel memory: 1852k freed
[    1.952812] Freeing unused kernel memory: 744k freed
[    4.460331] systemd-udevd[174]: starting version 197
[    5.504169] rtc_cmos 00:03: RTC can wake from S4
[    5.504498] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    5.504533] rtc_cmos 00:03: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
[    6.203157] Linux agpgart interface v0.103
[    6.222957] [drm] Initialized drm 1.1.0 20060810
[    6.310432] [drm] radeon kernel modesetting enabled.
[    6.310647] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[    6.310870] [drm] initializing kernel modesetting (RV380 0x1002:0x5B63 0x174B:0x1490).
[    6.310894] [drm] register mmio base: 0xFD7F0000
[    6.310895] [drm] register mmio size: 65536
[    6.311425] [drm] Generation 2 PCI interface, using max accessible memory
[    6.311431] radeon 0000:05:00.0: VRAM: 256M 0x00000000D0000000 - 0x00000000DFFFFFFF (256M used)
[    6.311433] radeon 0000:05:00.0: GTT: 512M 0x00000000B0000000 - 0x00000000CFFFFFFF
[    6.311447] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    6.311448] [drm] Driver supports precise vblank timestamp query.
[    6.311482] radeon 0000:05:00.0: irq 44 for MSI/MSI-X
[    6.311492] radeon 0000:05:00.0: radeon: using MSI.
[    6.311511] [drm] radeon: irq initialized.
[    6.311782] [drm] Detected VRAM RAM=256M, BAR=256M
[    6.311786] [drm] RAM width 128bits DDR
[    6.311871] [TTM] Zone  kernel: Available graphics memory: 1026812 kiB
[    6.311873] [TTM] Initializing pool allocator
[    6.311877] [TTM] Initializing DMA pool allocator
[    6.311909] [drm] radeon: 256M of VRAM memory ready
[    6.311910] [drm] radeon: 512M of GTT memory ready.
[    6.311929] [drm] GART: num cpu pages 131072, num gpu pages 131072
[    6.313373] [drm] radeon: 1 quad pipes, 1 Z pipes initialized.
[    6.314211] [drm] PCIE GART of 512M enabled (table at 0x00000000D0040000).
[    6.314237] radeon 0000:05:00.0: WB enabled
[    6.314241] radeon 0000:05:00.0: fence driver on ring 0 use gpu addr 0x00000000b0000000 and cpu addr 0xffff88007b795000
[    6.314293] [drm] Loading R300 Microcode
[    6.341738] [drm] radeon: ring at 0x00000000B0001000
[    6.341759] [drm] ring test succeeded in 1 usecs
[    6.341854] [drm] ib test succeeded in 0 usecs
[    6.342017] [drm] Radeon Display Connectors
[    6.342018] [drm] Connector 0:
[    6.342019] [drm]   VGA-1
[    6.342021] [drm]   DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[    6.342021] [drm]   Encoders:
[    6.342022] [drm]     CRT1: INTERNAL_DAC1
[    6.342023] [drm] Connector 1:
[    6.342024] [drm]   DVI-I-1
[    6.342025] [drm]   HPD1
[    6.342026] [drm]   DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[    6.342027] [drm]   Encoders:
[    6.342027] [drm]     CRT2: INTERNAL_DAC2
[    6.342028] [drm]     DFP1: INTERNAL_TMDS1
[    6.342029] [drm] Connector 2:
[    6.342030] [drm]   SVIDEO-1
[    6.342030] [drm]   Encoders:
[    6.342031] [drm]     TV1: INTERNAL_DAC2
[    6.380308] [drm] fb mappable at 0xD00C0000
[    6.380310] [drm] vram apper at 0xD0000000
[    6.380311] [drm] size 5185536
[    6.380311] [drm] fb depth is 24
[    6.380312] [drm]    pitch is 5760
[    6.380380] fbcon: radeondrmfb (fb0) is primary device
[    6.436142] Console: switching to colour frame buffer device 180x56
[    6.440895] radeon 0000:05:00.0: fb0: radeondrmfb frame buffer device
[    6.440896] radeon 0000:05:00.0: registered panic notifier
[    6.440901] [drm] Initialized radeon 2.32.0 20080528 for 0000:05:00.0 on minor 0
[    6.489934] ACPI: bus type USB registered
[    6.489967] usbcore: registered new interface driver usbfs
[    6.489980] usbcore: registered new interface driver hub
[    6.490054] usbcore: registered new device driver usb
[    6.514583] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.534157] ehci-pci: EHCI PCI platform driver
[    6.534292] ehci-pci 0000:00:02.1: setting latency timer to 64
[    6.534295] ehci-pci 0000:00:02.1: EHCI Host Controller
[    6.534301] ehci-pci 0000:00:02.1: new USB bus registered, assigned bus number 1
[    6.534311] ehci-pci 0000:00:02.1: debug port 1
[    6.534326] ehci-pci 0000:00:02.1: cache line size of 64 is not supported
[    6.534348] ehci-pci 0000:00:02.1: irq 22, io mem 0xfeb00000
[    6.540016] ehci-pci 0000:00:02.1: USB 2.0 started, EHCI 1.00
[    6.540276] hub 1-0:1.0: USB hub found
[    6.540281] hub 1-0:1.0: 10 ports detected
[    6.569858] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    6.569993] ohci_hcd 0000:00:02.0: setting latency timer to 64
[    6.569996] ohci_hcd 0000:00:02.0: OHCI Host Controller
[    6.570014] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[    6.570045] ohci_hcd 0000:00:02.0: irq 23, io mem 0xfe02f000
[    6.623144] hub 2-0:1.0: USB hub found
[    6.623151] hub 2-0:1.0: 10 ports detected
[    6.660182] usbcore: registered new interface driver usbhid
[    6.660185] usbhid: USB HID core driver
[    6.798474] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
[    6.798550] snd_emu10k1 0000:01:09.0: setting latency timer to 64
[    6.896697] powernow-k8: fid 0x11 (2500 MHz), vid 0xe
[    6.896700] powernow-k8: fid 0x10 (2400 MHz), vid 0xf
[    6.896702] powernow-k8: fid 0xe (2200 MHz), vid 0x11
[    6.896703] powernow-k8: fid 0xc (2000 MHz), vid 0x13
[    6.896704] powernow-k8: fid 0xa (1800 MHz), vid 0x15
[    6.896704] powernow-k8: fid 0x2 (1000 MHz), vid 0x16
[    6.896747] powernow-k8: Found 1 AMD Athlon(tm) Dual Core Processor 4850e (2 cpu cores) (version 2.20.00)
[    7.207030] usb 2-1: new low-speed USB device number 2 using ohci_hcd
[    7.276313] fuse init (API version 7.21)
[    7.564025] usb 2-4: new low-speed USB device number 3 using ohci_hcd
[    8.327120] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:02.0/usb2/2-1/2-1:1.0/input/input2
[    8.327210] hid-generic 0003:046D:C05A.0001: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:02.0-1/input0
[    8.327482] input: Logitech USB Keyboard as /devices/pci0000:00/0000:00:02.0/usb2/2-4/2-4:1.0/input/input3
[    8.327526] hid-generic 0003:046D:C31D.0002: input: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-0000:00:02.0-4/input0
[    8.331097] input: Logitech USB Keyboard as /devices/pci0000:00/0000:00:02.0/usb2/2-4/2-4:1.1/input/input4
[    8.331152] hid-generic 0003:046D:C31D.0003: input: USB HID v1.10 Device [Logitech USB Keyboard] on usb-0000:00:02.0-4/input1
[    8.513484] Adding 4000180k swap on /dev/sda3.  Priority:-1 extents:1 across:4000180k 
[    8.559817] XFS (sdb3): Mounting Filesystem
[    8.637340] XFS (sdb3): Ending clean mount
[   13.054400] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[   13.054630] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
[   13.054638] forcedeth 0000:00:0a.0: setting latency timer to 64
[   13.576311] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x5043 @ 1, addr 00:50:8d:94:24:45
[   13.576316] forcedeth 0000:00:0a.0: highdma csum gbit lnktim desc-v3
[   13.576573] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated).  Use CAP_NET_ADMIN and alias netdev-eth0 instead.
[   13.577014] forcedeth 0000:00:0a.0 eth0: no link during initialization
[   15.241829] forcedeth 0000:00:0a.0 eth0: link up
[   20.191228] ata1.00: configured for UDMA/133
[   20.191236] ata1: EH complete
[   20.226106] ata3.00: configured for UDMA/133
[   20.226115] ata3: EH complete
[   20.288200] ata4.00: configured for UDMA/133
[   20.288209] ata4: EH complete
[   22.034071] w83627ehf: Found W83627EHG chip at 0x290
[   22.034096] ACPI Warning: 0x0000000000000295-0x0000000000000296 SystemIO conflicts with Region \IP__ 1 (20130117/utaddress-251)
[   22.034102] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   22.041967] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
[   22.448717] Linux video capture interface: v2.00
[   22.490402] saa7130/34: v4l2 driver version 0, 2, 17 loaded
[   22.490739] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
[   22.490758] saa7133[0]: found at 0000:01:08.0, rev: 209, irq: 16, latency: 84, mmio: 0xfdeff000
[   22.490762] saa7133[0]: subsystem: 1043:4876, board: ASUSTeK P7131 Hybrid [card=112,insmod option]
[   22.490779] saa7133[0]: board init: gpio is 0
[   22.535017] Registered IR keymap rc-asus-pc39
[   22.535965] input: saa7134 IR (ASUSTeK P7131 Hybri as /devices/pci0000:00/0000:00:09.0/0000:01:08.0/rc/rc0/input5
[   22.536892] rc0: saa7134 IR (ASUSTeK P7131 Hybri as /devices/pci0000:00/0000:00:09.0/0000:01:08.0/rc/rc0
[   22.548187] IR RC5(x) protocol handler initialized
[   22.551986] lirc_dev: IR Remote Control driver registered, major 252 
[   22.561603] rc rc0: lirc_dev: driver ir-lirc-codec (saa7134) registered at minor = 0
[   22.561610] IR LIRC bridge handler initialized
[   22.680021] saa7133[0]: i2c eeprom 00: 43 10 76 48 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
[   22.680042] saa7133[0]: i2c eeprom 10: ff ff ff 0f ff 20 ff ff ff ff ff ff ff ff ff ff
[   22.680056] saa7133[0]: i2c eeprom 20: 01 40 01 02 03 01 01 03 08 ff 00 d5 ff ff ff ff
[   22.680071] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   22.680085] saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 55 50 ff ff ff ff ff ff
[   22.680099] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   22.680113] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   22.680127] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   22.680141] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   22.680155] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   22.680169] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   22.680183] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   22.680197] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   22.680211] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   22.680225] saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   22.680239] saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   22.683018] saa7133[0]: i2c scan: found device @ 0x10  [???]
[   22.694015] saa7133[0]: i2c scan: found device @ 0x96  [???]
[   22.696020] saa7133[0]: i2c scan: found device @ 0xa0  [eeprom]
[   22.743031] tuner 3-004b: Tuner -1 found with type(s) Radio TV.
[   22.778018] tda829x 3-004b: setting tuner address to 61
[   22.823021] tda829x 3-004b: type set to tda8290+75a
[   25.803193] saa7133[0]: registered device video0 [v4l2]
[   25.805070] saa7133[0]: registered device vbi0
[   25.805260] saa7133[0]: registered device radio0
[   25.846661] dvb_init() allocating 1 frontend
[   25.898042] DVB: registering new adapter (saa7133[0])
[   25.898061] saa7134 0000:01:08.0: DVB: registering adapter 0 frontend 0 (Philips TDA10046H DVB-T)...
[   25.950021] tda1004x: setting up plls for 48MHz sampling clock
[   26.111021] tda1004x: found firmware revision a5 -- invalid
[   26.111026] tda1004x: trying to boot from eeprom
[   26.432035] tda1004x: found firmware revision a5 -- invalid
[   26.432039] tda1004x: waiting for firmware upload...
[   32.702020] tda1004x: found firmware revision 20 -- ok
[   32.873118] saa7134 ALSA driver for DMA sound loaded
[   32.873167] saa7133[0]/alsa: saa7133[0] at 0xfdeff000 irq 16 registered as card -1
[   50.414557] ata1.00: configured for UDMA/133
[   50.414567] ata1: EH complete
[   50.425763] ata3.00: configured for UDMA/133
[   50.425770] ata3: EH complete
[   50.508269] ata4.00: configured for UDMA/133
[   50.508276] ata4: EH complete
[   51.065576] PM: Syncing filesystems ... done.
[   51.092365] Freezing user space processes ... (elapsed 0.01 seconds) done.
[   51.103123] ACPI: Preparing to enter system sleep state S4
[   51.103439] PM: Preallocating image memory... done (allocated 56475 pages)
[   51.148715] PM: Allocated 225900 kbytes in 0.04 seconds (5647.50 MB/s)
[   51.148717] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[   51.159207] Suspending console(s) (use no_console_suspend to debug)
[   51.238415] PM: freeze of devices complete after 79.200 msecs
[   51.238668] PM: late freeze of devices complete after 0.249 msecs
[   51.238899] PM: noirq freeze of devices complete after 0.229 msecs
[   51.238938] PM: Saving platform NVS memory
[   51.238988] Disabling non-boot CPUs ...
[   51.240280] smpboot: CPU 1 is now offline
[   51.240678] PM: Creating hibernation image:
[   51.241273] PM: Need to copy 60409 pages
[   51.241273] PM: Restoring platform NVS memory
[   51.241273] Force enabled HPET at resume
[   51.241273] Enabling non-boot CPUs ...
[   51.241273] smpboot: Booting Node 0 Processor 1 APIC 0x1
[   51.251987] CPU1 is up
[   51.252334] ACPI: Waking up from system sleep state S4
[   51.252708] pci 0000:00:00.0: Found enabled HT MSI Mapping
[   51.252748] pci 0000:00:00.0: Found enabled HT MSI Mapping
[   51.252790] pci 0000:00:00.0: Found enabled HT MSI Mapping
[   51.252833] pci 0000:00:00.0: Found enabled HT MSI Mapping
[   51.274171] PM: noirq restore of devices complete after 21.637 msecs
[   51.274296] PM: early restore of devices complete after 0.097 msecs
[   51.292695] ohci_hcd 0000:00:02.0: setting latency timer to 64
[   51.292699] ehci-pci 0000:00:02.1: setting latency timer to 64
[   51.292733] pci 0000:00:09.0: setting latency timer to 64
[   51.292747] pata_amd 0000:00:06.0: setting latency timer to 64
[   51.293247] sata_nv 0000:00:07.0: setting latency timer to 64
[   51.293255] saa7133[0]: board init: gpio is 0
[   51.293278] radeon 0000:05:00.0: ffff88007c6ae000 unpin not necessary
[   51.293333] sata_nv 0000:00:08.0: setting latency timer to 64
[   51.345048] usb usb2: root hub lost power or was reset
[   51.345075] usb usb1: root hub lost power or was reset
[   51.345087] ehci-pci 0000:00:02.1: cache line size of 64 is not supported
[   51.400154] [drm] radeon: 1 quad pipes, 1 Z pipes initialized.
[   51.401424] [drm] PCIE GART of 512M enabled (table at 0x00000000D0040000).
[   51.401432] radeon 0000:05:00.0: WB enabled
[   51.401435] radeon 0000:05:00.0: fence driver on ring 0 use gpu addr 0x00000000b0000000 and cpu addr 0xffff88007b795000
[   51.401448] [drm] radeon: ring at 0x00000000B0001000
[   51.401468] [drm] ring test succeeded in 1 usecs
[   51.401495] [drm] ib test succeeded in 0 usecs
[   51.482339] ata6.01: ACPI cmd ef/03:42:00:00:00:b0 (SET FEATURES) filtered out
[   51.482341] ata6.01: ACPI cmd ef/03:0c:00:00:00:b0 (SET FEATURES) filtered out
[   51.485293] ata6.00: ACPI cmd ef/03:44:00:00:00:a0 (SET FEATURES) filtered out
[   51.485295] ata6.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[   51.485305] ata6: nv_mode_filter: 0x1f39f&0x1f39f->0x1f39f, BIOS=0x1f000 (0xc5c0) ACPI=0x1f01f (30:60:0x1f)
[   51.485308] ata6: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc5c0) ACPI=0x701f (30:60:0x1f)
[   51.491213] ata6.00: configured for UDMA/66
[   51.513255] ata6.01: configured for UDMA/33
[   51.755022] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[   51.755024] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   51.755083] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   51.758139] ata4.00: ACPI cmd ef/03:46:00:00:00:a0 (SET FEATURES) filtered out
[   51.758186] ata3.00: ACPI cmd ef/03:46:00:00:00:a0 (SET FEATURES) filtered out
[   51.758275] ata1.00: ACPI cmd ef/03:46:00:00:00:a0 (SET FEATURES) filtered out
[   51.761191] ata4.00: configured for UDMA/133
[   51.761233] sd 3:0:0:0: [sdc] Starting disk
[   51.762644] ata1.00: configured for UDMA/133
[   51.762680] sd 0:0:0:0: [sda] Starting disk
[   51.763199] ata3.00: configured for UDMA/133
[   51.763235] sd 2:0:0:0: [sdb] Starting disk
[   51.814710] forcedeth 0000:00:0a.0 eth0: no link during initialization
[   51.920026] usb 2-1: reset low-speed USB device number 2 using ohci_hcd
[   52.024013] ata2: SATA link down (SStatus 0 SControl 300)
[   52.553018] usb 2-4: reset low-speed USB device number 3 using ohci_hcd
[   53.565158] forcedeth 0000:00:0a.0 eth0: link up
[   53.877017] PM: restore of devices complete after 2584.378 msecs
[   53.877285] Restarting tasks ... done.
[   54.041264] ata1.00: configured for UDMA/133
[   54.041275] ata1: EH complete
[   54.052278] ata3.00: configured for UDMA/133
[   54.052288] ata3: EH complete
[   54.108278] ata4.00: configured for UDMA/133
[   54.108286] ata4: EH complete

^ permalink raw reply	[flat|nested] 16+ messages in thread