* TI AR7 7200 - no boot
@ 2010-03-03 10:11 Dea_RU
2010-03-03 10:24 ` Florian Fainelli
0 siblings, 1 reply; 9+ messages in thread
From: Dea_RU @ 2010-03-03 10:11 UTC (permalink / raw)
To: linux-mips
I build kernel 2.6.33 for TI AR7 cpu 7200 version.
boot halt on console init stage/
gcc 4.3.3
==============================
linwork:/opt/mipsel32/usr/bin# ./mipsel-linux-gcc-4.3.3 -v
Using built-in specs.
Target: mipsel-uclibc-linux
Configured with:
/Acorp/buildroot-2010.02-rc1/output/toolchain/gcc-4.3.3/configure
--prefix=/usr --build=i386-cross-linux-uclibc --host=i386-cross-linux-uclibc
--target=mipsel-uclibc-linux --enable-languages=c,c++
--with-sysroot=/opt/mipsel32/
--with-build-time-tools=/opt/mipsel32//usr/mipsel-uclibc-linux/bin
--disable-__cxa_atexit --enable-target-optspace --with-gnu-ld
--disable-libssp --enable-tls --enable-shared
--with-gmp=/Acorp/buildroot-2010.02-rc1/output/toolchain/gmp
--with-mpfr=/Acorp/buildroot-2010.02-rc1/output/toolchain/mpfr --disable-nls
--enable-threads --disable-multilib --disable-decimal-float --with-abi=32
--with-tune=mips1 --disable-largefile --with-endian=little,big
--with-pkgversion='Buildroot 2010.02-rc1'
--with-bugurl=http://bugs.buildroot.net/ : (reconfigured)
/Acorp/buildroot-2010.02-rc1/output/toolchain/gcc-4.3.3/configure
--prefix=/usr --build=i386-cross-linux-uclibc --host=i386-cross-linux-uclibc
--target=mipsel-uclibc-linux --enable-languages=c,c++
--with-sysroot=/opt/mipsel32/
--with-build-time-tools=/opt/mipsel32//usr/mipsel-uclibc-linux/bin
--disable-__cxa_atexit --enable-target-optspace --with-gnu-ld
--disable-libssp --enable-tls --enable-shared
--with-gmp=/Acorp/buildroot-2010.02-rc1/output/toolchain/gmp
--with-mpfr=/Acorp/buildroot-2010.02-rc1/output/toolchain/mpfr --disable-nls
--enable-threads --disable-multilib --disable-decimal-float --with-abi=32
--with-tune=mips1 --disable-largefile --with-pkgversion='Buildroot
2010.02-rc1' --with-bugurl=http://bugs.buildroot.net/
Thread model: posix
gcc version 4.3.3 (Buildroot 2010.02-rc1)
===========
kernel cfg
CONFIG_MIPS=y
CONFIG_AR7=y
CONFIG_LOONGSON_UART_BASE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_ARCH_SUPPORTS_OPROFILE=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_SCHED_OMIT_FRAME_POINTER=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_BOOT_RAW=y
CONFIG_CEVT_R4K_LIB=y
CONFIG_CEVT_R4K=y
CONFIG_CSRC_R4K_LIB=y
CONFIG_CSRC_R4K=y
CONFIG_DMA_NONCOHERENT=y
CONFIG_DMA_NEED_PCI_MAP_STATE=y
CONFIG_SYS_HAS_EARLY_PRINTK=y
CONFIG_GENERIC_GPIO=y
CONFIG_CPU_LITTLE_ENDIAN=y
CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
CONFIG_IRQ_CPU=y
CONFIG_NO_EXCEPT_FILL=y
CONFIG_SWAP_IO_SPACE=y
CONFIG_MIPS_L1_CACHE_SHIFT=5
CONFIG_CPU_MIPS32_R1=y
CONFIG_SYS_SUPPORTS_ZBOOT=y
CONFIG_SYS_SUPPORTS_ZBOOT_UART16550=y
CONFIG_SYS_HAS_CPU_MIPS32_R1=y
CONFIG_CPU_MIPS32=y
CONFIG_CPU_MIPSR1=y
CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
CONFIG_HARDWARE_WATCHPOINTS=y
CONFIG_32BIT=y
CONFIG_PAGE_SIZE_4KB=y
CONFIG_CPU_HAS_PREFETCH=y
CONFIG_MIPS_MT_DISABLED=y
CONFIG_CPU_HAS_SYNC=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_CPU_SUPPORTS_HIGHMEM=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_HZ_250=y
CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
CONFIG_HZ=250
CONFIG_PREEMPT_NONE=y
CONFIG_SECCOMP=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_CONSTRUCTORS=y
# General setup
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_HAVE_KERNEL_GZIP=y
CONFIG_HAVE_KERNEL_BZIP2=y
CONFIG_HAVE_KERNEL_LZMA=y
CONFIG_HAVE_KERNEL_LZO=y
CONFIG_KERNEL_LZMA=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
# RCU Subsystem
CONFIG_TINY_RCU=y
CONFIG_LOG_BUF_SHIFT=17
CONFIG_GROUP_SCHED=y
CONFIG_FAIR_GROUP_SCHED=y
CONFIG_USER_SCHED=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_ANON_INODES=y
CONFIG_EMBEDDED=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
# Kernel Performance Events And Counters
CONFIG_SLAB=y
CONFIG_HAVE_OPROFILE=y
# GCOV-based kernel profiling
CONFIG_SLOW_WORK=y
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_FORCE_LOAD=y
CONFIG_INLINE_SPIN_UNLOCK=y
CONFIG_INLINE_SPIN_UNLOCK_IRQ=y
CONFIG_INLINE_READ_UNLOCK=y
CONFIG_INLINE_READ_UNLOCK_IRQ=y
CONFIG_INLINE_WRITE_UNLOCK=y
CONFIG_INLINE_WRITE_UNLOCK_IRQ=y
# Bus options (PCI, PCMCIA, EISA, ISA, TC)
CONFIG_MMU=y
# Executable file formats
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=y
CONFIG_TRAD_SIGNALS=y
# Power management options
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
# Device Drivers
# Generic Driver Options
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_MTD=y
CONFIG_MTD_DEBUG=y
CONFIG_MTD_DEBUG_VERBOSE=0
# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_AR7_PARTS=y
# RAM/ROM/Flash chip drivers
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# Input device support
CONFIG_INPUT=y
# Character devices
CONFIG_VT=y
CONFIG_HW_CONSOLE=y
# Serial drivers
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=2
CONFIG_SERIAL_8250_RUNTIME_UARTS=2
# Non-8250 serial port support
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_UNIX98_PTYS=y
CONFIG_DEVPTS_MULTIPLE_INSTANCES=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# PPS support
CONFIG_PPS=y
CONFIG_PPS_DEBUG=y
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_NOWAYOUT=y
# Watchdog Device Drivers
CONFIG_AR7_WDT=y
CONFIG_SSB_POSSIBLE=y
# Console display driver support
CONFIG_DUMMY_CONSOLE=y
CONFIG_ACCESSIBILITY=y
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_DEBUG=y
# RTC interfaces
CONFIG_RTC_INTF_SYSFS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
CONFIG_RTC_INTF_DEV_UIE_EMUL=y
CONFIG_RTC_DRV_TEST=y
# on-CPU RTC drivers
CONFIG_AUXDISPLAY=y
CONFIG_UIO=y
# TI VLYNQ
CONFIG_VLYNQ=y
CONFIG_STAGING=y
CONFIG_STAGING_EXCLUDE_BUILD=y
# File systems
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
CONFIG_AUTOFS_FS=y
CONFIG_AUTOFS4_FS=y
# Caches
CONFIG_FSCACHE=y
CONFIG_FSCACHE_DEBUG=y
# Pseudo filesystems
CONFIG_PROC_FS=y
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
# Kernel hacking
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_UNUSED_SYMBOLS=y
CONFIG_DEBUG_MEMORY_INIT=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_TRACING_SUPPORT=y
CONFIG_HAVE_ARCH_KGDB=y
CONFIG_EARLY_PRINTK=y
CONFIG_CMDLINE_BOOL=y
CONFIG_CMDLINE="earlyprintk=ttyS0,9600n,keep"
# Security options
CONFIG_DEFAULT_SECURITY_DAC=y
CONFIG_DEFAULT_SECURITY=""
CONFIG_CRYPTO=y
# Crypto core or helper
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_BLKCIPHER2=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_HASH2=y
CONFIG_CRYPTO_RNG2=y
CONFIG_CRYPTO_PCOMP=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_MANAGER2=y
CONFIG_CRYPTO_NULL=y
CONFIG_CRYPTO_WORKQUEUE=y
# Hash modes
CONFIG_CRYPTO_HMAC=y
# Digest
CONFIG_CRYPTO_CRC32C=y
CONFIG_CRYPTO_MD4=y
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=y
# Ciphers
CONFIG_CRYPTO_AES=y
# Compression
CONFIG_CRYPTO_DEFLATE=y
CONFIG_CRYPTO_ZLIB=y
CONFIG_CRYPTO_LZO=y
# Library routines
CONFIG_BITREVERSE=y
CONFIG_GENERIC_FIND_LAST_BIT=y
CONFIG_CRC_CCITT=y
CONFIG_CRC16=y
CONFIG_CRC_T10DIF=y
CONFIG_CRC_ITU_T=y
CONFIG_CRC32=y
CONFIG_CRC7=y
CONFIG_LIBCRC32C=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_LZO_COMPRESS=y
CONFIG_LZO_DECOMPRESS=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_NLATTR=y
===========
booting process:
===========
(psbl)
Booting...
Linux version 2.6.33 (root@linwork) (gcc version 4.3.3 (Buildroot
2010.02-rc1) ) #1 Wed Mar 3 15:31:18 OMST 2010
bootconsole [early0] enabled
CPU revision is: 00018448 (MIPS 4KEc)
TI AR7 (TNETD7200), ID: 0x002b, Revision: 0x11
Determined physical RAM map:
memory: 01000000 @ 14000000 (usable)
Zone PFN ranges:
Normal 0x00014000 -> 0x00015000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00014000 -> 0x00015000
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: console=ttyS0,9600n8 earlyprintk=ttyS0,9600
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 8kB, 4-way, VIPT, no aliases, linesize 16 bytes
Memory: 13164k/16384k available (1325k kernel code, 3220k reserved, 408k
data, 120k init, 0k highmem)
NR_IRQS:256
Console: colour dummy device 80x25
==============
stop booting...
what wrong ????
kernels from open-wrt booting with log:
==============================
(psbl)
Booting...
Linux version 2.6.26.8 (agb@arrakis) (gcc version 4.1.2) #1 Wed Dec 2
15:14:35 UTC 2009
console [early0] enabled
CPU revision is: 00018448 (MIPS 4KEc)
Clocks: Sync 2:1 mode
Clocks: Setting CPU clock
Adjusted requested frequency 211000000 to 211968000
Clocks: base = 35328000, frequency = 211968000, prediv = 1, postdiv = 1,
postdiv2 = -1, mul = 6
Clocks: Setting DSP clock
Clocks: base = 25000000, frequency = 105984000, prediv = 1, postdiv = 2,
postdiv2 = 1, mul = 10
Clocks: Setting USB clock
Adjusted requested frequency 48000000 to 47863741
Clocks: base = 105984000, frequency = 48000000, prediv = 1, postdiv = 31,
postdiv2 = -1, mul = 14
TI AR7 (TNETD7200), ID: 0x002b, Revision: 0x11
Determined physical RAM map:
memory: 01000000 @ 14000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 81920 -> 86016
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 81920 -> 86016
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: init=/etc/preinit rootfstype=squashfs,jffs2,
console=ttyS0,9600n8
Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 8kB, 4-way, VIPT, no aliases, linesize 16 bytes
PID hash table entries: 64 (order: 6, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 12560k/16384k available (2001k kernel code, 3824k reserved, 417k
data, 124k init, 0k highmem)
SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
net_namespace: 644 bytes
NET: Registered protocol family 16
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 24
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x8610e00 (irq = 15) is a TI-AR7
--
View this message in context: http://old.nabble.com/TI-AR7-7200---no-boot-tp27766331p27766331.html
Sent from the linux-mips main mailing list archive at Nabble.com.
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: TI AR7 7200 - no boot
2010-03-03 10:11 TI AR7 7200 - no boot Dea_RU
@ 2010-03-03 10:24 ` Florian Fainelli
2010-03-03 10:59 ` Dea_RU
0 siblings, 1 reply; 9+ messages in thread
From: Florian Fainelli @ 2010-03-03 10:24 UTC (permalink / raw)
To: Dea_RU; +Cc: linux-mips
Hi,
On Wednesday 03 March 2010 11:11:31 Dea_RU wrote:
> I build kernel 2.6.33 for TI AR7 cpu 7200 version.
>
> boot halt on console init stage/
[snip]
>
> CONFIG_MIPS=y
>
> CONFIG_AR7=y
> CONFIG_LOONGSON_UART_BASE=y
> CONFIG_RWSEM_GENERIC_SPINLOCK=y
> CONFIG_ARCH_SUPPORTS_OPROFILE=y
> CONFIG_GENERIC_FIND_NEXT_BIT=y
> CONFIG_GENERIC_HWEIGHT=y
> CONFIG_GENERIC_CALIBRATE_DELAY=y
> CONFIG_GENERIC_CLOCKEVENTS=y
> CONFIG_GENERIC_TIME=y
> CONFIG_GENERIC_CMOS_UPDATE=y
> CONFIG_SCHED_OMIT_FRAME_POINTER=y
> CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
> CONFIG_BOOT_RAW=y
[snip]
>
> what wrong ????
>
> kernels from open-wrt booting with log:
> ==============================
> (psbl)
>
> Booting...
> Linux version 2.6.26.8 (agb@arrakis) (gcc version 4.1.2) #1 Wed Dec 2
> 15:14:35 UTC 2009
> console [early0] enabled
> CPU revision is: 00018448 (MIPS 4KEc)
> Clocks: Sync 2:1 mode
> Clocks: Setting CPU clock
> Adjusted requested frequency 211000000 to 211968000
> Clocks: base = 35328000, frequency = 211968000, prediv = 1, postdiv = 1,
> postdiv2 = -1, mul = 6
> Clocks: Setting DSP clock
> Clocks: base = 25000000, frequency = 105984000, prediv = 1, postdiv = 2,
> postdiv2 = 1, mul = 10
> Clocks: Setting USB clock
> Adjusted requested frequency 48000000 to 47863741
> Clocks: base = 105984000, frequency = 48000000, prediv = 1, postdiv = 31,
> postdiv2 = -1, mul = 14
> TI AR7 (TNETD7200), ID: 0x002b, Revision: 0x11
> Determined physical RAM map:
> memory: 01000000 @ 14000000 (usable)
> Initrd not found or empty - disabling initrd
> Zone PFN ranges:
> Normal 81920 -> 86016
> Movable zone start PFN for each node
> early_node_map[1] active PFN ranges
> 0: 81920 -> 86016
> Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
> Kernel command line: init=/etc/preinit rootfstype=squashfs,jffs2,
> console=ttyS0,9600n8
> Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
> Primary data cache 8kB, 4-way, VIPT, no aliases, linesize 16 bytes
> PID hash table entries: 64 (order: 6, 256 bytes)
> Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
> Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
> Memory: 12560k/16384k available (2001k kernel code, 3824k reserved, 417k
> data, 124k init, 0k highmem)
> SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> Mount-cache hash table entries: 512
> net_namespace: 644 bytes
> NET: Registered protocol family 16
> NET: Registered protocol family 2
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> TCP established hash table entries: 512 (order: 0, 4096 bytes)
> TCP bind hash table entries: 512 (order: -1, 2048 bytes)
> TCP: Hash tables configured (established 512 bind 512)
> TCP reno registered
> NET: Registered protocol family 1
> squashfs: version 3.0 (2006/03/15) Phillip Lougher
> Registering mini_fo version $Id$
> JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
> msgmni has been set to 24
> io scheduler noop registered
> io scheduler deadline registered (default)
> Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
> serial8250: ttyS0 at MMIO 0x8610e00 (irq = 15) is a TI-AR7
>
You have one of these devices with bogus UART, (there are quite some out there)
can you try with the following patch and tell me if that gives you an usable console:
diff --git a/arch/mips/ar7/platform.c b/arch/mips/ar7/platform.c
index 246df7a..15cbeeb 100644
--- a/arch/mips/ar7/platform.c
+++ b/arch/mips/ar7/platform.c
@@ -551,6 +551,7 @@ static int __init ar7_register_uarts(void)
uart_port.irq = AR7_IRQ_UART0;
uart_port.mapbase = AR7_REGS_UART0;
uart_port.membase = ioremap(uart_port.mapbase, 256);
+ uart_port.flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF;
res = early_serial_setup(&uart_port);
if (res)
@@ -562,6 +563,7 @@ static int __init ar7_register_uarts(void)
uart_port.irq = AR7_IRQ_UART1;
uart_port.mapbase = UR8_REGS_UART1;
uart_port.membase = ioremap(uart_port.mapbase, 256);
+ uart_port.flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF;
res = early_serial_setup(&uart_port);
if (res)
Thanks.
--
Regards, Florian
^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: TI AR7 7200 - no boot
2010-03-03 10:24 ` Florian Fainelli
@ 2010-03-03 10:59 ` Dea_RU
2010-03-03 12:58 ` Dea_RU
0 siblings, 1 reply; 9+ messages in thread
From: Dea_RU @ 2010-03-03 10:59 UTC (permalink / raw)
To: linux-mips
Florian Fainelli-4 wrote:
>
> Hi,
>
> You have one of these devices with bogus UART, (there are quite some out
> there)
> can you try with the following patch and tell me if that gives you an
> usable console:
>
> diff --git a/arch/mips/ar7/platform.c b/arch/mips/ar7/platform.c
> index 246df7a..15cbeeb 100644
> --- a/arch/mips/ar7/platform.c
> +++ b/arch/mips/ar7/platform.c
> @@ -551,6 +551,7 @@ static int __init ar7_register_uarts(void)
> uart_port.irq = AR7_IRQ_UART0;
> uart_port.mapbase = AR7_REGS_UART0;
> uart_port.membase = ioremap(uart_port.mapbase, 256);
> + uart_port.flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF;
>
> res = early_serial_setup(&uart_port);
> if (res)
> @@ -562,6 +563,7 @@ static int __init ar7_register_uarts(void)
> uart_port.irq = AR7_IRQ_UART1;
> uart_port.mapbase = UR8_REGS_UART1;
> uart_port.membase = ioremap(uart_port.mapbase, 256);
> + uart_port.flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF;
>
> res = early_serial_setup(&uart_port);
> if (res)
>
> Thanks.
> --
> Regards, Florian
>
after remark printk with message console color line 2927 /drivers/char/vt.c
boot process stop with:
====================
....
Primary data cache 8kB, 4-way, VIPT, no aliases, linesize 16 bytes
Memory: 13172k/16384k available (1314k kernel code, 3212k reserved, 411k
data, 120k init, 0k highmem)
NR_IRQS:256
Calibrating delay loop...
===============
next freeze on delay loop clculation !? IRQ not init correctly ???
maby after send byte over USART cpu set flag "USART TX buffer cleared"? and
kernel go to interput vector ???
=========
in kernel src 2.6.33 from mips.org patch based code not present !
/arch/mips/ar7/platform.c
i added port number flags for version 2.6.33 ....
uart_port[0].flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF;
uart_port[1].flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF;
==============
after added flags and remark console collor booting stop with:
......
Primary data cache 8kB, 4-way, VIPT, no aliases, linesize 16 bytes
Memory: 13172k/16384k available (1314k kernel code, 3212k reserved, 411k
data, 120k init, 0k highmem)
NR_IRQS:256
Calibrating delay loop...
--
View this message in context: http://old.nabble.com/TI-AR7-7200---no-boot-tp27766331p27766728.html
Sent from the linux-mips main mailing list archive at Nabble.com.
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: TI AR7 7200 - no boot
2010-03-03 10:59 ` Dea_RU
@ 2010-03-03 12:58 ` Dea_RU
2010-03-03 13:04 ` Florian Fainelli
0 siblings, 1 reply; 9+ messages in thread
From: Dea_RU @ 2010-03-03 12:58 UTC (permalink / raw)
To: linux-mips
i adder printk(...) before all function in kernel init funktion /init/main.c
log show last message before called fundtion local_irq_enable().
If delete my debug printk-s kernel stop after first console output
"Calibrating delay loop... "
I do not MIPS arch interput specific ..... Can be MIPS need init internel
timer and link overflow flag to interput ??
------ log with added printk ----
......
Memory: 13172k/16384k available (1314k kernel code, 3212k reserved, 411k
data, 120k init, 0k highmem)
early_irq_init
NR_IRQS:256 <- kernel
init_IRQ
prio_tree_init
init_timers
hrtimers_init
softirq_init
timerkepping_init
time init
profile_init
early_boot_irqs_on
local_irq_enable <- last my debug printk message before call to
local_irq_enable()
-------------------------------
--
View this message in context: http://old.nabble.com/TI-AR7-7200---no-boot-tp27766331p27767861.html
Sent from the linux-mips main mailing list archive at Nabble.com.
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: TI AR7 7200 - no boot
2010-03-03 12:58 ` Dea_RU
@ 2010-03-03 13:04 ` Florian Fainelli
2010-03-03 14:24 ` Dea_RU
2010-03-03 15:54 ` Alexander Clouter
0 siblings, 2 replies; 9+ messages in thread
From: Florian Fainelli @ 2010-03-03 13:04 UTC (permalink / raw)
To: Dea_RU; +Cc: linux-mips
On Wednesday 03 March 2010 13:58:48 Dea_RU wrote:
> i adder printk(...) before all function in kernel init funktion
> /init/main.c
>
> log show last message before called fundtion local_irq_enable().
>
> If delete my debug printk-s kernel stop after first console output
> "Calibrating delay loop... "
>
> I do not MIPS arch interput specific ..... Can be MIPS need init internel
> timer and link overflow flag to interput ??
All handlers are not correctly setup, so you should include this patch in your
tree:
http://www.linux-mips.org/archives/linux-mips/2010-01/msg00019.html
>
>
> ------ log with added printk ----
> ......
> Memory: 13172k/16384k available (1314k kernel code, 3212k reserved, 411k
> data, 120k init, 0k highmem)
> early_irq_init
> NR_IRQS:256 <- kernel
> init_IRQ
> prio_tree_init
> init_timers
> hrtimers_init
> softirq_init
> timerkepping_init
> time init
> profile_init
> early_boot_irqs_on
> local_irq_enable <- last my debug printk message before call to
> local_irq_enable()
> -------------------------------
>
--
Regards, Florian
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: TI AR7 7200 - no boot
2010-03-03 13:04 ` Florian Fainelli
@ 2010-03-03 14:24 ` Dea_RU
2010-03-03 19:20 ` Dea_RU
2010-03-03 15:54 ` Alexander Clouter
1 sibling, 1 reply; 9+ messages in thread
From: Dea_RU @ 2010-03-03 14:24 UTC (permalink / raw)
To: linux-mips
it work !
great work !
why this patch not present in src 2.6.33 ???
============ log
(psbl)
Booting...
Linux version 2.6.33 (root@linwork) (gcc version 4.3.3 (Buildroot
2010.02-rc1) ) #13 Wed Mar 3 20:04:20 OMST 2010
bootconsole [early0] enabled
CPU revision is: 00018448 (MIPS 4KEc)
TI AR7 (TNETD7200), ID: 0x002b, Revision: 0x11
Determined physical RAM map:
memory: 01000000 @ 14000000 (usable)
Zone PFN ranges:
Normal 0x00014000 -> 0x00015000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00014000 -> 0x00015000
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: console=ttyS0,9600n8 earlyprintk=ttyS0,9600
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 8kB, 4-way, VIPT, no aliases, linesize 16 bytes
Memory: 13172k/16384k available (1316k kernel code, 3212k reserved, 409k
data, 120k init, 0k highmem)
NR_IRQS:256
Console: colour dummy device 80x25
Calibrating delay loop... 149.50 BogoMIPS (lpj=299008)
Mount-cache hash table entries: 512
rest_init
Clocks: Sync 2:1 mode
Clocks: Setting CPU clock
Adjusted requested frequency 211000000 to 211968000
Clocks: base = 35328000, frequency = 211968000, prediv = 1, postdiv = 1,
postdiv2 = -1, mul = 6
Clocks: Setting DSP clock
Clocks: base = 25000000, frequency = 105984000, prediv = 1, postdiv = 2,
postdiv2 = 1, mul = 10
Clocks: Setting USB clock
Adjusted requested frequency 48000000 to 47863741
Clocks: base = 105984000, frequency = 48000000, prediv = 1, postdiv = 31,
postdiv2 = -1, mul = 14
LinuxPPS API ver. 1 registered
Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
<giometti@linux.it>
Switching to clocksource MIPS
Slow work thread pool: Starting up
Slow work thread pool: Ready
FS-Cache: Loaded
msgmni has been set to 25
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x8610e00 (irq = 15) is a XScale
Ã}q™ya)\x01¶‰/½¾£Ö ².W,XvÍ!a\x06™,Ó\x17¯\“×
---------- can not select USART options for show it ...
--
View this message in context: http://old.nabble.com/TI-AR7-7200---no-boot-tp27766331p27768844.html
Sent from the linux-mips main mailing list archive at Nabble.com.
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: TI AR7 7200 - no boot
2010-03-03 13:04 ` Florian Fainelli
2010-03-03 14:24 ` Dea_RU
@ 2010-03-03 15:54 ` Alexander Clouter
1 sibling, 0 replies; 9+ messages in thread
From: Alexander Clouter @ 2010-03-03 15:54 UTC (permalink / raw)
To: linux-mips
Florian Fainelli <florian@openwrt.org> wrote:
>
> On Wednesday 03 March 2010 13:58:48 Dea_RU wrote:
>>
>> If delete my debug printk-s kernel stop after first console output
>> "Calibrating delay loop... "
>>
>> I do not MIPS arch interput specific ..... Can be MIPS need init internel
>> timer and link overflow flag to interput ??
>
> All handlers are not correctly setup, so you should include this patch in your
> tree:
>
> http://www.linux-mips.org/archives/linux-mips/2010-01/msg00019.html
>
If I could slip in with some shameless self advertising:
http://www.digriz.org.uk/wag54g
Same(ish) chipset, the 'Creating Firmwares' section should interest you
and get you started on your buildroot journey.
Cheers
--
Alexander Clouter
.sigmonster says: guru, n:
A computer owner who can read the manual.
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: TI AR7 7200 - no boot
2010-03-03 14:24 ` Dea_RU
@ 2010-03-03 19:20 ` Dea_RU
2010-03-03 20:05 ` Florian Fainelli
0 siblings, 1 reply; 9+ messages in thread
From: Dea_RU @ 2010-03-03 19:20 UTC (permalink / raw)
To: linux-mips
I show this rtunk left 10 day....
and patch src 2.6.33 from dir root/trunk/target/linux/ar7/patches-2.6.32
to day i see :
florian: [ar7] add missing patch to arch/mips/kernel/traps.c to allow ar7 to
setup … :confused:
------------------
for 2.6.33 need this modify ?? or not ?
arch/mips/include/asm/page.h
---------
#define UNCAC_ADDR(addr) ((addr) - PAGE_OFFSET + UNCAC_BASE +
PHYS_OFFSET)
#define CAC_ADDR(addr) ((addr) - UNCAC_BASE + PAGE_OFFSET -
PHYS_OFFSET)
---------
----------------
my console not work correctly - baudrate no standart ?! :( i change port
type
---- i change port type in ar7platform.c to:
uart_port[0].type = PORT_16550A
to
uart_port[0].type = PORT_AR7
boot process ttyS0 detected as AR7.
Console baudrate not work correct again ....&-(
======= log ================
............
alg: No test for stdrng (krng)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x8610e00 (irq = 15) is a AR7
Id\x10Á\x05\x16Id\x10Á\x05\x12Id\x10Á\x05\x12Id\x10Á\x05\x12Id\x10Á\x05\x12Id\x10Á\x05\x12Yd\x10Á\x05\x12Yd\x10Á\x05\x12Yd\x10Á\x05\x12Yd\x10Á\x05\x12Yd\x10Á\x05\x12Yd\x10Á\x05\x12Yd\x10Á\x05\x12Yd\x10Á\x05\x12Yd\x10Á\x05\x16Yd\x10Á\x05\x16Yd\x10Á\x05\x16Yd\x10
......
==========================
if remart set_termios() in serial_core.c i see all messages ...
--
View this message in context: http://old.nabble.com/TI-AR7-7200---no-boot-tp27766331p27772495.html
Sent from the linux-mips main mailing list archive at Nabble.com.
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: TI AR7 7200 - no boot
2010-03-03 19:20 ` Dea_RU
@ 2010-03-03 20:05 ` Florian Fainelli
0 siblings, 0 replies; 9+ messages in thread
From: Florian Fainelli @ 2010-03-03 20:05 UTC (permalink / raw)
To: Dea_RU; +Cc: linux-mips
[-- Attachment #1: Type: Text/Plain, Size: 1781 bytes --]
Hi,
Le mercredi 3 mars 2010 20:20:22, Dea_RU a écrit :
> I show this rtunk left 10 day....
>
> and patch src 2.6.33 from dir root/trunk/target/linux/ar7/patches-2.6.32
Ok, then why do not you simply use OpenWrt trunk?
>
> to day i see :
>
> florian: [ar7] add missing patch to arch/mips/kernel/traps.c to allow ar7
> to setup … :confused:
>
> ------------------
> for 2.6.33 need this modify ?? or not ?
>
> arch/mips/include/asm/page.h
> ---------
> #define UNCAC_ADDR(addr) ((addr) - PAGE_OFFSET + UNCAC_BASE +
> PHYS_OFFSET)
> #define CAC_ADDR(addr) ((addr) - UNCAC_BASE + PAGE_OFFSET -
> PHYS_OFFSET)
> ---------
This is not needed.
>
>
> ----------------
> my console not work correctly - baudrate no standart ?! :( i change port
> type
>
> ---- i change port type in ar7platform.c to:
>
> uart_port[0].type = PORT_16550A
> to
> uart_port[0].type = PORT_AR7
>
> boot process ttyS0 detected as AR7.
>
> Console baudrate not work correct again ....&-(
You will also need this patch:
https://dev.openwrt.org/browser/trunk/target/linux/ar7/patches-2.6.32/500-
serial_kludge.patch
>
> ======= log ================
> ............
> alg: No test for stdrng (krng)
> Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
> serial8250: ttyS0 at MMIO 0x8610e00 (irq = 15) is a AR7
> Id\x10Á\x05\x16Id\x10Á\x05\x12Id\x10Á\x05\x12Id\x10Á\x05\x12Id\x10Á\x05\x12Id\x10Á\x05\x12Yd\x10Á\x05\x12Yd\x10Á\x05\x12Yd\x10Á\x05\x12Yd\x10Á\x05\x12Yd\x10Á\x05\x12Yd\x10Á\x05\x12Yd\x10
> Á\x05\x12Yd\x10Á\x05\x12Yd\x10Á\x05\x16Yd\x10Á\x05\x16Yd\x10Á\x05\x16Yd\x10 ......
>
> ==========================
>
> if remart set_termios() in serial_core.c i see all messages ...
>
--
Best regards, Florian Fainelli
Email: florian@openwrt.org
Web: http://openwrt.org
IRC: [florian] on irc.freenode.net
-------------------------------
[-- Attachment #2: This is a digitally signed message part. --]
[-- Type: application/pgp-signature, Size: 198 bytes --]
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2010-03-03 20:05 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-03-03 10:11 TI AR7 7200 - no boot Dea_RU
2010-03-03 10:24 ` Florian Fainelli
2010-03-03 10:59 ` Dea_RU
2010-03-03 12:58 ` Dea_RU
2010-03-03 13:04 ` Florian Fainelli
2010-03-03 14:24 ` Dea_RU
2010-03-03 19:20 ` Dea_RU
2010-03-03 20:05 ` Florian Fainelli
2010-03-03 15:54 ` Alexander Clouter
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.