* [PATCH v4 0/8] Add support for Hikey 970 PCIe
@ 2021-07-12 21:46 ` Mauro Carvalho Chehab
0 siblings, 0 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-12 21:46 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
Manivannan Sadhasivam, Rob Herring, Krzysztof Wilczyński,
Binghui Wang, Rob Herring, Xiaowei Song, devicetree,
linux-arm-kernel, linux-kernel, linux-pci, linux-phy
As requested by Rob Herring, this series split the PHY part into a separate driver.
Then, it adds support for Kirin 970 on a single patch.
With this change, the PHY-specific device tree bindings for Kirin 960 moved
to its own PHY properties.
Tested on Hikey970:
$ lspci
00:00.0 PCI bridge: Huawei Technologies Co., Ltd. Device 3670 (rev 01)
01:00.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:01.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:04.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:05.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:07.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:09.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 07)
$ ethtool enp6s0
Settings for enp6s0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Link partner advertised pause frame use: Symmetric Receive-only
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: on
master-slave cfg: preferred slave
master-slave status: slave
Port: Twisted Pair
PHYAD: 0
Transceiver: external
MDI-X: Unknown
netlink error: Operation not permitted
Link detected: yes
Partially tested on Hikey 960[1]:
$ lspci
00:00.0 PCI bridge: Huawei Technologies Co., Ltd. Device 3660 (rev 01)
[1] The Hikey 960 doesn't come with any internal PCIe device.
Its hardware supports just an external device via a M.2 slot that
doesn't support SATA. I ordered a NVMe device to test, but the vendor
is currently out of supply. It should take 4-5 weeks to arrive here. I'll
run an extra test on it once it arrives.
---
v4:
- dropped the DTS patch, as it depends on a PMIC-related patch series;
- minor changes at the patch description;
- HiKey and HiSilicon are now using the preferred CamelCase format.
Mauro Carvalho Chehab (8):
dt-bindings: phy: Add bindings for HiKey 960 PCIe PHY
dt-bindings: phy: Add bindings for HiKey 970 PCIe PHY
dt-bindings: PCI: kirin: Fix compatible string
dt-bindings: PCI: kirin: Drop PHY properties
phy: HiSilicon: Add driver for Kirin 960 PCIe PHY
phy: HiSilicon: add driver for Kirin 970 PCIe PHY
PCI: kirin: Drop the PHY logic from the driver
PCI: kirin: Use regmap for APB registers
.../devicetree/bindings/pci/kirin-pcie.txt | 21 +-
.../phy/hisilicon,phy-hi3660-pcie.yaml | 82 ++
.../phy/hisilicon,phy-hi3670-pcie.yaml | 101 ++
arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 29 +-
drivers/pci/controller/dwc/pcie-kirin.c | 298 ++----
drivers/phy/hisilicon/Kconfig | 20 +
drivers/phy/hisilicon/Makefile | 2 +
drivers/phy/hisilicon/phy-hi3660-pcie.c | 325 +++++++
drivers/phy/hisilicon/phy-hi3670-pcie.c | 892 ++++++++++++++++++
9 files changed, 1500 insertions(+), 270 deletions(-)
create mode 100644 Documentation/devicetree/bindings/phy/hisilicon,phy-hi3660-pcie.yaml
create mode 100644 Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml
create mode 100644 drivers/phy/hisilicon/phy-hi3660-pcie.c
create mode 100644 drivers/phy/hisilicon/phy-hi3670-pcie.c
--
2.31.1
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v4 0/8] Add support for Hikey 970 PCIe
@ 2021-07-12 21:46 ` Mauro Carvalho Chehab
0 siblings, 0 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-12 21:46 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
Manivannan Sadhasivam, Rob Herring, Krzysztof Wilczyński,
Binghui Wang, Rob Herring, Xiaowei Song, devicetree,
linux-arm-kernel, linux-kernel, linux-pci, linux-phy
As requested by Rob Herring, this series split the PHY part into a separate driver.
Then, it adds support for Kirin 970 on a single patch.
With this change, the PHY-specific device tree bindings for Kirin 960 moved
to its own PHY properties.
Tested on Hikey970:
$ lspci
00:00.0 PCI bridge: Huawei Technologies Co., Ltd. Device 3670 (rev 01)
01:00.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:01.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:04.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:05.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:07.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:09.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 07)
$ ethtool enp6s0
Settings for enp6s0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Link partner advertised pause frame use: Symmetric Receive-only
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: on
master-slave cfg: preferred slave
master-slave status: slave
Port: Twisted Pair
PHYAD: 0
Transceiver: external
MDI-X: Unknown
netlink error: Operation not permitted
Link detected: yes
Partially tested on Hikey 960[1]:
$ lspci
00:00.0 PCI bridge: Huawei Technologies Co., Ltd. Device 3660 (rev 01)
[1] The Hikey 960 doesn't come with any internal PCIe device.
Its hardware supports just an external device via a M.2 slot that
doesn't support SATA. I ordered a NVMe device to test, but the vendor
is currently out of supply. It should take 4-5 weeks to arrive here. I'll
run an extra test on it once it arrives.
---
v4:
- dropped the DTS patch, as it depends on a PMIC-related patch series;
- minor changes at the patch description;
- HiKey and HiSilicon are now using the preferred CamelCase format.
Mauro Carvalho Chehab (8):
dt-bindings: phy: Add bindings for HiKey 960 PCIe PHY
dt-bindings: phy: Add bindings for HiKey 970 PCIe PHY
dt-bindings: PCI: kirin: Fix compatible string
dt-bindings: PCI: kirin: Drop PHY properties
phy: HiSilicon: Add driver for Kirin 960 PCIe PHY
phy: HiSilicon: add driver for Kirin 970 PCIe PHY
PCI: kirin: Drop the PHY logic from the driver
PCI: kirin: Use regmap for APB registers
.../devicetree/bindings/pci/kirin-pcie.txt | 21 +-
.../phy/hisilicon,phy-hi3660-pcie.yaml | 82 ++
.../phy/hisilicon,phy-hi3670-pcie.yaml | 101 ++
arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 29 +-
drivers/pci/controller/dwc/pcie-kirin.c | 298 ++----
drivers/phy/hisilicon/Kconfig | 20 +
drivers/phy/hisilicon/Makefile | 2 +
drivers/phy/hisilicon/phy-hi3660-pcie.c | 325 +++++++
drivers/phy/hisilicon/phy-hi3670-pcie.c | 892 ++++++++++++++++++
9 files changed, 1500 insertions(+), 270 deletions(-)
create mode 100644 Documentation/devicetree/bindings/phy/hisilicon,phy-hi3660-pcie.yaml
create mode 100644 Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml
create mode 100644 drivers/phy/hisilicon/phy-hi3660-pcie.c
create mode 100644 drivers/phy/hisilicon/phy-hi3670-pcie.c
--
2.31.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v4 0/8] Add support for Hikey 970 PCIe
@ 2021-07-12 21:46 ` Mauro Carvalho Chehab
0 siblings, 0 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-12 21:46 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
Manivannan Sadhasivam, Rob Herring, Krzysztof Wilczyński,
Binghui Wang, Rob Herring, Xiaowei Song, devicetree,
linux-arm-kernel, linux-kernel, linux-pci, linux-phy
As requested by Rob Herring, this series split the PHY part into a separate driver.
Then, it adds support for Kirin 970 on a single patch.
With this change, the PHY-specific device tree bindings for Kirin 960 moved
to its own PHY properties.
Tested on Hikey970:
$ lspci
00:00.0 PCI bridge: Huawei Technologies Co., Ltd. Device 3670 (rev 01)
01:00.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:01.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:04.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:05.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:07.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:09.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 07)
$ ethtool enp6s0
Settings for enp6s0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Link partner advertised pause frame use: Symmetric Receive-only
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: on
master-slave cfg: preferred slave
master-slave status: slave
Port: Twisted Pair
PHYAD: 0
Transceiver: external
MDI-X: Unknown
netlink error: Operation not permitted
Link detected: yes
Partially tested on Hikey 960[1]:
$ lspci
00:00.0 PCI bridge: Huawei Technologies Co., Ltd. Device 3660 (rev 01)
[1] The Hikey 960 doesn't come with any internal PCIe device.
Its hardware supports just an external device via a M.2 slot that
doesn't support SATA. I ordered a NVMe device to test, but the vendor
is currently out of supply. It should take 4-5 weeks to arrive here. I'll
run an extra test on it once it arrives.
---
v4:
- dropped the DTS patch, as it depends on a PMIC-related patch series;
- minor changes at the patch description;
- HiKey and HiSilicon are now using the preferred CamelCase format.
Mauro Carvalho Chehab (8):
dt-bindings: phy: Add bindings for HiKey 960 PCIe PHY
dt-bindings: phy: Add bindings for HiKey 970 PCIe PHY
dt-bindings: PCI: kirin: Fix compatible string
dt-bindings: PCI: kirin: Drop PHY properties
phy: HiSilicon: Add driver for Kirin 960 PCIe PHY
phy: HiSilicon: add driver for Kirin 970 PCIe PHY
PCI: kirin: Drop the PHY logic from the driver
PCI: kirin: Use regmap for APB registers
.../devicetree/bindings/pci/kirin-pcie.txt | 21 +-
.../phy/hisilicon,phy-hi3660-pcie.yaml | 82 ++
.../phy/hisilicon,phy-hi3670-pcie.yaml | 101 ++
arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 29 +-
drivers/pci/controller/dwc/pcie-kirin.c | 298 ++----
drivers/phy/hisilicon/Kconfig | 20 +
drivers/phy/hisilicon/Makefile | 2 +
drivers/phy/hisilicon/phy-hi3660-pcie.c | 325 +++++++
drivers/phy/hisilicon/phy-hi3670-pcie.c | 892 ++++++++++++++++++
9 files changed, 1500 insertions(+), 270 deletions(-)
create mode 100644 Documentation/devicetree/bindings/phy/hisilicon,phy-hi3660-pcie.yaml
create mode 100644 Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml
create mode 100644 drivers/phy/hisilicon/phy-hi3660-pcie.c
create mode 100644 drivers/phy/hisilicon/phy-hi3670-pcie.c
--
2.31.1
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v4 1/8] dt-bindings: phy: Add bindings for HiKey 960 PCIe PHY
2021-07-12 21:46 ` Mauro Carvalho Chehab
@ 2021-07-12 21:46 ` Mauro Carvalho Chehab
-1 siblings, 0 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-12 21:46 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
Manivannan Sadhasivam, Rob Herring, Kishon Vijay Abraham I,
Rob Herring, Vinod Koul, devicetree, linux-kernel, linux-phy
Document the bindings for HiKey 960 (hi3660) PCIe PHY
interface, supported via the pcie-kirin driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
.../phy/hisilicon,phy-hi3660-pcie.yaml | 82 +++++++++++++++++++
1 file changed, 82 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/hisilicon,phy-hi3660-pcie.yaml
diff --git a/Documentation/devicetree/bindings/phy/hisilicon,phy-hi3660-pcie.yaml b/Documentation/devicetree/bindings/phy/hisilicon,phy-hi3660-pcie.yaml
new file mode 100644
index 000000000000..81c93e76cef4
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/hisilicon,phy-hi3660-pcie.yaml
@@ -0,0 +1,82 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/hisilicon,phy-hi3660-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: HiSilicon Kirin960 PCIe PHY
+
+maintainers:
+ - Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
+
+description: |+
+ Bindings for PCIe PHY on HiSilicon Kirin 960.
+
+properties:
+ compatible:
+ const: hisilicon,hi960-pcie-phy
+
+ "#phy-cells":
+ const: 0
+
+ reg:
+ maxItems: 1
+ description: PHY Control registers
+
+ reg-names:
+ const: phy
+
+ clocks:
+ items:
+ - description: PCIe PHY clock
+ - description: PCIe AUX clock
+ - description: PCIe APB PHY clock
+ - description: PCIe APB SYS clock
+ - description: PCIe ACLK clock
+
+ clock-names:
+ items:
+ - const: pcie_phy_ref
+ - const: pcie_aux
+ - const: pcie_apb_phy
+ - const: pcie_apb_sys
+ - const: pcie_aclk
+
+ reset-gpios:
+ description: PCI PERST reset GPIO
+
+required:
+ - "#phy-cells"
+ - compatible
+ - reg
+ - reg-names
+ - clocks
+ - clock-names
+ - reset-gpios
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/hi3660-clock.h>
+
+ bus {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ pcie_phy: pcie-phy@f3f2000 {
+ compatible = "hisilicon,hi960-pcie-phy";
+ reg = <0x0 0xf3f20000 0x0 0x40000>;
+ reg-names = "phy";
+ clocks = <&crg_ctrl HI3660_PCIEPHY_REF>,
+ <&crg_ctrl HI3660_CLK_GATE_PCIEAUX>,
+ <&crg_ctrl HI3660_PCLK_GATE_PCIE_PHY>,
+ <&crg_ctrl HI3660_PCLK_GATE_PCIE_SYS>,
+ <&crg_ctrl HI3660_ACLK_GATE_PCIE>;
+ clock-names = "pcie_phy_ref", "pcie_aux",
+ "pcie_apb_phy", "pcie_apb_sys",
+ "pcie_aclk";
+ reset-gpios = <&gpio11 1 0 >;
+ #phy-cells = <0>;
+ };
+ };
+...
--
2.31.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 1/8] dt-bindings: phy: Add bindings for HiKey 960 PCIe PHY
@ 2021-07-12 21:46 ` Mauro Carvalho Chehab
0 siblings, 0 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-12 21:46 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
Manivannan Sadhasivam, Rob Herring, Kishon Vijay Abraham I,
Rob Herring, Vinod Koul, devicetree, linux-kernel, linux-phy
Document the bindings for HiKey 960 (hi3660) PCIe PHY
interface, supported via the pcie-kirin driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
.../phy/hisilicon,phy-hi3660-pcie.yaml | 82 +++++++++++++++++++
1 file changed, 82 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/hisilicon,phy-hi3660-pcie.yaml
diff --git a/Documentation/devicetree/bindings/phy/hisilicon,phy-hi3660-pcie.yaml b/Documentation/devicetree/bindings/phy/hisilicon,phy-hi3660-pcie.yaml
new file mode 100644
index 000000000000..81c93e76cef4
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/hisilicon,phy-hi3660-pcie.yaml
@@ -0,0 +1,82 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/hisilicon,phy-hi3660-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: HiSilicon Kirin960 PCIe PHY
+
+maintainers:
+ - Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
+
+description: |+
+ Bindings for PCIe PHY on HiSilicon Kirin 960.
+
+properties:
+ compatible:
+ const: hisilicon,hi960-pcie-phy
+
+ "#phy-cells":
+ const: 0
+
+ reg:
+ maxItems: 1
+ description: PHY Control registers
+
+ reg-names:
+ const: phy
+
+ clocks:
+ items:
+ - description: PCIe PHY clock
+ - description: PCIe AUX clock
+ - description: PCIe APB PHY clock
+ - description: PCIe APB SYS clock
+ - description: PCIe ACLK clock
+
+ clock-names:
+ items:
+ - const: pcie_phy_ref
+ - const: pcie_aux
+ - const: pcie_apb_phy
+ - const: pcie_apb_sys
+ - const: pcie_aclk
+
+ reset-gpios:
+ description: PCI PERST reset GPIO
+
+required:
+ - "#phy-cells"
+ - compatible
+ - reg
+ - reg-names
+ - clocks
+ - clock-names
+ - reset-gpios
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/hi3660-clock.h>
+
+ bus {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ pcie_phy: pcie-phy@f3f2000 {
+ compatible = "hisilicon,hi960-pcie-phy";
+ reg = <0x0 0xf3f20000 0x0 0x40000>;
+ reg-names = "phy";
+ clocks = <&crg_ctrl HI3660_PCIEPHY_REF>,
+ <&crg_ctrl HI3660_CLK_GATE_PCIEAUX>,
+ <&crg_ctrl HI3660_PCLK_GATE_PCIE_PHY>,
+ <&crg_ctrl HI3660_PCLK_GATE_PCIE_SYS>,
+ <&crg_ctrl HI3660_ACLK_GATE_PCIE>;
+ clock-names = "pcie_phy_ref", "pcie_aux",
+ "pcie_apb_phy", "pcie_apb_sys",
+ "pcie_aclk";
+ reset-gpios = <&gpio11 1 0 >;
+ #phy-cells = <0>;
+ };
+ };
+...
--
2.31.1
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 2/8] dt-bindings: phy: Add bindings for HiKey 970 PCIe PHY
2021-07-12 21:46 ` Mauro Carvalho Chehab
@ 2021-07-12 21:46 ` Mauro Carvalho Chehab
-1 siblings, 0 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-12 21:46 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
Manivannan Sadhasivam, Rob Herring, Kishon Vijay Abraham I,
Rob Herring, Vinod Koul, devicetree, linux-kernel, linux-phy
Document the bindings for HiKey 970 (hi3670) PCIe PHY
interface, supported via the pcie-kirin driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
.../phy/hisilicon,phy-hi3670-pcie.yaml | 101 ++++++++++++++++++
1 file changed, 101 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml
diff --git a/Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml b/Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml
new file mode 100644
index 000000000000..976ab6fe7b0a
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml
@@ -0,0 +1,101 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/hisilicon,phy-hi3670-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: HiSilicon Kirin970 PCIe PHY
+
+maintainers:
+ - Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
+
+description: |+
+ Bindings for PCIe PHY on HiSilicon Kirin 970.
+
+properties:
+ compatible:
+ const: hisilicon,hi970-pcie-phy
+
+ "#phy-cells":
+ const: 0
+
+ reg:
+ maxItems: 1
+ description: PHY Control registers
+
+ reg-names:
+ const: phy
+
+ phy-supply:
+ description: The PCIe PHY power supply
+
+ clocks:
+ items:
+ - description: PCIe PHY clock
+ - description: PCIe AUX clock
+ - description: PCIe APB PHY clock
+ - description: PCIe APB SYS clock
+ - description: PCIe ACLK clock
+
+ clock-names:
+ items:
+ - const: pcie_phy_ref
+ - const: pcie_aux
+ - const: pcie_apb_phy
+ - const: pcie_apb_sys
+ - const: pcie_aclk
+
+ reset-gpios:
+ description: PCI PERST reset GPIOs
+ maxItems: 4
+
+ clkreq-gpios:
+ description: Clock request GPIOs
+ maxItems: 3
+
+ hisilicon,eye-diagram-param:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description: Eye diagram for phy.
+
+required:
+ - "#phy-cells"
+ - compatible
+ - reg
+ - reg-names
+ - clocks
+ - clock-names
+ - reset-gpios
+ - clkreq-gpios
+ - hisilicon,eye-diagram-param
+ - phy-supply
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/hi3670-clock.h>
+
+ bus {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ pcie_phy: pcie-phy@fc000000 {
+ compatible = "hisilicon,hi970-pcie-phy";
+ reg = <0x0 0xfc000000 0x0 0x80000>;
+ reg-names = "phy";
+ #phy-cells = <0>;
+ phy-supply = <&ldo33>;
+ clocks = <&crg_ctrl HI3670_CLK_GATE_PCIEPHY_REF>,
+ <&crg_ctrl HI3670_CLK_GATE_PCIEAUX>,
+ <&crg_ctrl HI3670_PCLK_GATE_PCIE_PHY>,
+ <&crg_ctrl HI3670_PCLK_GATE_PCIE_SYS>,
+ <&crg_ctrl HI3670_ACLK_GATE_PCIE>;
+ clock-names = "pcie_phy_ref", "pcie_aux",
+ "pcie_apb_phy", "pcie_apb_sys", "pcie_aclk";
+ reset-gpios = <&gpio7 0 0 >, <&gpio25 2 0 >,
+ <&gpio3 1 0 >, <&gpio27 4 0 >;
+ clkreq-gpios = <&gpio20 6 0 >, <&gpio27 3 0 >, <&gpio17 0 0 >;
+ hisilicon,eye-diagram-param = <0xFFFFFFFF 0xFFFFFFFF
+ 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF>;
+ };
+ };
+...
--
2.31.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 2/8] dt-bindings: phy: Add bindings for HiKey 970 PCIe PHY
@ 2021-07-12 21:46 ` Mauro Carvalho Chehab
0 siblings, 0 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-12 21:46 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
Manivannan Sadhasivam, Rob Herring, Kishon Vijay Abraham I,
Rob Herring, Vinod Koul, devicetree, linux-kernel, linux-phy
Document the bindings for HiKey 970 (hi3670) PCIe PHY
interface, supported via the pcie-kirin driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
.../phy/hisilicon,phy-hi3670-pcie.yaml | 101 ++++++++++++++++++
1 file changed, 101 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml
diff --git a/Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml b/Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml
new file mode 100644
index 000000000000..976ab6fe7b0a
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml
@@ -0,0 +1,101 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/hisilicon,phy-hi3670-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: HiSilicon Kirin970 PCIe PHY
+
+maintainers:
+ - Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
+
+description: |+
+ Bindings for PCIe PHY on HiSilicon Kirin 970.
+
+properties:
+ compatible:
+ const: hisilicon,hi970-pcie-phy
+
+ "#phy-cells":
+ const: 0
+
+ reg:
+ maxItems: 1
+ description: PHY Control registers
+
+ reg-names:
+ const: phy
+
+ phy-supply:
+ description: The PCIe PHY power supply
+
+ clocks:
+ items:
+ - description: PCIe PHY clock
+ - description: PCIe AUX clock
+ - description: PCIe APB PHY clock
+ - description: PCIe APB SYS clock
+ - description: PCIe ACLK clock
+
+ clock-names:
+ items:
+ - const: pcie_phy_ref
+ - const: pcie_aux
+ - const: pcie_apb_phy
+ - const: pcie_apb_sys
+ - const: pcie_aclk
+
+ reset-gpios:
+ description: PCI PERST reset GPIOs
+ maxItems: 4
+
+ clkreq-gpios:
+ description: Clock request GPIOs
+ maxItems: 3
+
+ hisilicon,eye-diagram-param:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description: Eye diagram for phy.
+
+required:
+ - "#phy-cells"
+ - compatible
+ - reg
+ - reg-names
+ - clocks
+ - clock-names
+ - reset-gpios
+ - clkreq-gpios
+ - hisilicon,eye-diagram-param
+ - phy-supply
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/hi3670-clock.h>
+
+ bus {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ pcie_phy: pcie-phy@fc000000 {
+ compatible = "hisilicon,hi970-pcie-phy";
+ reg = <0x0 0xfc000000 0x0 0x80000>;
+ reg-names = "phy";
+ #phy-cells = <0>;
+ phy-supply = <&ldo33>;
+ clocks = <&crg_ctrl HI3670_CLK_GATE_PCIEPHY_REF>,
+ <&crg_ctrl HI3670_CLK_GATE_PCIEAUX>,
+ <&crg_ctrl HI3670_PCLK_GATE_PCIE_PHY>,
+ <&crg_ctrl HI3670_PCLK_GATE_PCIE_SYS>,
+ <&crg_ctrl HI3670_ACLK_GATE_PCIE>;
+ clock-names = "pcie_phy_ref", "pcie_aux",
+ "pcie_apb_phy", "pcie_apb_sys", "pcie_aclk";
+ reset-gpios = <&gpio7 0 0 >, <&gpio25 2 0 >,
+ <&gpio3 1 0 >, <&gpio27 4 0 >;
+ clkreq-gpios = <&gpio20 6 0 >, <&gpio27 3 0 >, <&gpio17 0 0 >;
+ hisilicon,eye-diagram-param = <0xFFFFFFFF 0xFFFFFFFF
+ 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF>;
+ };
+ };
+...
--
2.31.1
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 3/8] dt-bindings: PCI: kirin: Fix compatible string
2021-07-12 21:46 ` Mauro Carvalho Chehab
` (3 preceding siblings ...)
(?)
@ 2021-07-12 21:46 ` Mauro Carvalho Chehab
-1 siblings, 0 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-12 21:46 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
Manivannan Sadhasivam, Rob Herring, Binghui Wang, Bjorn Helgaas,
Rob Herring, Xiaowei Song, devicetree, linux-kernel, linux-pci
The pcie-kirin driver doesn't declare a hisilicon,kirin-pcie.
Also, remove the useless comment after the description, as other
compat will be supported by the same driver in the future.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
Documentation/devicetree/bindings/pci/kirin-pcie.txt | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/pci/kirin-pcie.txt b/Documentation/devicetree/bindings/pci/kirin-pcie.txt
index 6bbe43818ad5..71cac2b74002 100644
--- a/Documentation/devicetree/bindings/pci/kirin-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/kirin-pcie.txt
@@ -9,7 +9,7 @@ Additional properties are described here:
Required properties
- compatible:
- "hisilicon,kirin960-pcie" for PCIe of Kirin960 SoC
+ "hisilicon,kirin960-pcie"
- reg: Should contain rc_dbi, apb, phy, config registers location and length.
- reg-names: Must include the following entries:
"dbi": controller configuration registers;
@@ -23,7 +23,7 @@ Optional properties:
Example based on kirin960:
pcie@f4000000 {
- compatible = "hisilicon,kirin-pcie";
+ compatible = "hisilicon,kirin960-pcie";
reg = <0x0 0xf4000000 0x0 0x1000>, <0x0 0xff3fe000 0x0 0x1000>,
<0x0 0xf3f20000 0x0 0x40000>, <0x0 0xF4000000 0 0x2000>;
reg-names = "dbi","apb","phy", "config";
--
2.31.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 4/8] dt-bindings: PCI: kirin: Drop PHY properties
2021-07-12 21:46 ` Mauro Carvalho Chehab
` (4 preceding siblings ...)
(?)
@ 2021-07-12 21:46 ` Mauro Carvalho Chehab
-1 siblings, 0 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-12 21:46 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
Manivannan Sadhasivam, Rob Herring, Binghui Wang, Bjorn Helgaas,
Rob Herring, Xiaowei Song, devicetree, linux-kernel, linux-pci
There are several properties there that belong to the PHY
interface. Drop them, as a new binding file will describe
the PHY properties for Kirin 960.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
.../devicetree/bindings/pci/kirin-pcie.txt | 16 +++-------------
1 file changed, 3 insertions(+), 13 deletions(-)
diff --git a/Documentation/devicetree/bindings/pci/kirin-pcie.txt b/Documentation/devicetree/bindings/pci/kirin-pcie.txt
index 71cac2b74002..a93a8cfa1afb 100644
--- a/Documentation/devicetree/bindings/pci/kirin-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/kirin-pcie.txt
@@ -10,13 +10,11 @@ Additional properties are described here:
Required properties
- compatible:
"hisilicon,kirin960-pcie"
-- reg: Should contain rc_dbi, apb, phy, config registers location and length.
+- reg: Should contain rc_dbi, apb, config registers location and length.
- reg-names: Must include the following entries:
"dbi": controller configuration registers;
"apb": apb Ctrl register defined by Kirin;
- "phy": apb PHY register defined by Kirin;
"config": PCIe configuration space registers.
-- reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
Optional properties:
@@ -25,8 +23,8 @@ Example based on kirin960:
pcie@f4000000 {
compatible = "hisilicon,kirin960-pcie";
reg = <0x0 0xf4000000 0x0 0x1000>, <0x0 0xff3fe000 0x0 0x1000>,
- <0x0 0xf3f20000 0x0 0x40000>, <0x0 0xF4000000 0 0x2000>;
- reg-names = "dbi","apb","phy", "config";
+ <0x0 0xF4000000 0 0x2000>;
+ reg-names = "dbi","apb", "config";
bus-range = <0x0 0x1>;
#address-cells = <3>;
#size-cells = <2>;
@@ -39,12 +37,4 @@ Example based on kirin960:
<0x0 0 0 2 &gic 0 0 0 283 4>,
<0x0 0 0 3 &gic 0 0 0 284 4>,
<0x0 0 0 4 &gic 0 0 0 285 4>;
- clocks = <&crg_ctrl HI3660_PCIEPHY_REF>,
- <&crg_ctrl HI3660_CLK_GATE_PCIEAUX>,
- <&crg_ctrl HI3660_PCLK_GATE_PCIE_PHY>,
- <&crg_ctrl HI3660_PCLK_GATE_PCIE_SYS>,
- <&crg_ctrl HI3660_ACLK_GATE_PCIE>;
- clock-names = "pcie_phy_ref", "pcie_aux",
- "pcie_apb_phy", "pcie_apb_sys", "pcie_aclk";
- reset-gpios = <&gpio11 1 0 >;
};
--
2.31.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 5/8] phy: HiSilicon: Add driver for Kirin 960 PCIe PHY
2021-07-12 21:46 ` Mauro Carvalho Chehab
@ 2021-07-12 21:46 ` Mauro Carvalho Chehab
-1 siblings, 0 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-12 21:46 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
Manivannan Sadhasivam, Rob Herring, Greg Kroah-Hartman,
Kishon Vijay Abraham I, Vinod Koul, linux-kernel, linux-phy
The pcie-kirin PCIe driver contains internally a PHY interface for
a Kirin 960. As we'll be adding support also for Kirin 970 PHY, we
need to first split the PHY into a separate driver.
So, add a new driver with just the PHY part of
drivers/pci/controller/dwc/pcie-kirin.c.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
drivers/phy/hisilicon/Kconfig | 10 +
drivers/phy/hisilicon/Makefile | 1 +
drivers/phy/hisilicon/phy-hi3660-pcie.c | 325 ++++++++++++++++++++++++
3 files changed, 336 insertions(+)
create mode 100644 drivers/phy/hisilicon/phy-hi3660-pcie.c
diff --git a/drivers/phy/hisilicon/Kconfig b/drivers/phy/hisilicon/Kconfig
index 4d008cfc279c..30b7f1187965 100644
--- a/drivers/phy/hisilicon/Kconfig
+++ b/drivers/phy/hisilicon/Kconfig
@@ -23,6 +23,16 @@ config PHY_HI3660_USB
To compile this driver as a module, choose M here.
+config PHY_HI3660_PCIE
+ tristate "hi3660 PCIe PHY support"
+ depends on (ARCH_HISI && ARM64) || COMPILE_TEST
+ select GENERIC_PHY
+ select MFD_SYSCON
+ help
+ Enable this to support the HiSilicon hi3660 PCIe PHY.
+
+ To compile this driver as a module, choose M here.
+
config PHY_HI3670_USB
tristate "hi3670 USB PHY support"
depends on (ARCH_HISI && ARM64) || COMPILE_TEST
diff --git a/drivers/phy/hisilicon/Makefile b/drivers/phy/hisilicon/Makefile
index 51729868145b..3c3d70dd7469 100644
--- a/drivers/phy/hisilicon/Makefile
+++ b/drivers/phy/hisilicon/Makefile
@@ -1,6 +1,7 @@
# SPDX-License-Identifier: GPL-2.0-only
obj-$(CONFIG_PHY_HI6220_USB) += phy-hi6220-usb.o
obj-$(CONFIG_PHY_HI3660_USB) += phy-hi3660-usb3.o
+obj-$(CONFIG_PHY_HI3660_PCIE) += phy-hi3660-pcie.o
obj-$(CONFIG_PHY_HI3670_USB) += phy-hi3670-usb3.o
obj-$(CONFIG_PHY_HISTB_COMBPHY) += phy-histb-combphy.o
obj-$(CONFIG_PHY_HISI_INNO_USB2) += phy-hisi-inno-usb2.o
diff --git a/drivers/phy/hisilicon/phy-hi3660-pcie.c b/drivers/phy/hisilicon/phy-hi3660-pcie.c
new file mode 100644
index 000000000000..130314b0e8cb
--- /dev/null
+++ b/drivers/phy/hisilicon/phy-hi3660-pcie.c
@@ -0,0 +1,325 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * PCIe phy driver for Kirin 960
+ *
+ * Copyright (C) 2017 HiSilicon Electronics Co., Ltd.
+ * https://www.huawei.com
+ *
+ * Copyright (C) 2021 Huawei Electronics Co., Ltd.
+ * https://www.huawei.com
+ *
+ * Author:
+ * Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
+ */
+
+#include <linux/clk.h>
+#include <linux/gpio.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define REF_CLK_FREQ 100000000
+
+/* info located in APB PHY */
+#define PCIE_APB_PHY_CTRL0 0x0
+#define PCIE_APB_PHY_CTRL1 0x4
+#define PCIE_APB_PHY_STATUS0 0x400
+#define PIPE_CLK_STABLE BIT(19)
+#define PHY_REF_PAD_BIT BIT(8)
+#define PHY_PWR_DOWN_BIT BIT(22)
+#define PHY_RST_ACK_BIT BIT(16)
+
+/* info located in sysctrl */
+#define SCTRL_PCIE_CMOS_OFFSET 0x60
+#define SCTRL_PCIE_CMOS_BIT 0x10
+#define SCTRL_PCIE_ISO_OFFSET 0x44
+#define SCTRL_PCIE_ISO_BIT 0x30
+#define SCTRL_PCIE_HPCLK_OFFSET 0x190
+#define SCTRL_PCIE_HPCLK_BIT 0x184000
+#define SCTRL_PCIE_OE_OFFSET 0x14a
+#define PCIE_DEBOUNCE_PARAM 0xF0F400
+#define PCIE_OE_BYPASS (0x3 << 28)
+
+/* peri_crg ctrl */
+#define CRGCTRL_PCIE_ASSERT_OFFSET 0x88
+#define CRGCTRL_PCIE_ASSERT_BIT 0x8c000000
+
+/* Time for delay */
+#define REF_2_PERST_MIN 20000
+#define REF_2_PERST_MAX 25000
+#define PERST_2_ACCESS_MIN 10000
+#define PERST_2_ACCESS_MAX 12000
+#define PIPE_CLK_WAIT_MIN 550
+#define PIPE_CLK_WAIT_MAX 600
+#define TIME_CMOS_MIN 100
+#define TIME_CMOS_MAX 105
+#define TIME_PHY_PD_MIN 10
+#define TIME_PHY_PD_MAX 11
+
+struct hi3660_pcie_phy {
+ struct device *dev;
+ void __iomem *base;
+ struct regmap *crgctrl;
+ struct regmap *sysctrl;
+ struct clk *apb_sys_clk;
+ struct clk *apb_phy_clk;
+ struct clk *phy_ref_clk;
+ struct clk *pcie_aclk;
+ struct clk *pcie_aux_clk;
+ int gpio_id_reset;
+};
+
+/* Registers in PCIePHY */
+static inline void kirin_apb_phy_writel(struct hi3660_pcie_phy *hi3660_pcie_phy,
+ u32 val, u32 reg)
+{
+ writel(val, hi3660_pcie_phy->base + reg);
+}
+
+static inline u32 kirin_apb_phy_readl(struct hi3660_pcie_phy *hi3660_pcie_phy,
+ u32 reg)
+{
+ return readl(hi3660_pcie_phy->base + reg);
+}
+
+static void hi3660_pcie_phy_oe_enable(struct hi3660_pcie_phy *phy)
+{
+ u32 val;
+
+ regmap_read(phy->sysctrl, SCTRL_PCIE_OE_OFFSET, &val);
+ val |= PCIE_DEBOUNCE_PARAM;
+ val &= ~PCIE_OE_BYPASS;
+ regmap_write(phy->sysctrl, SCTRL_PCIE_OE_OFFSET, val);
+}
+
+
+static int kirin_pcie_clk_ctrl(struct hi3660_pcie_phy *phy, bool enable)
+{
+ int ret = 0;
+
+ if (!enable)
+ goto close_clk;
+
+ ret = clk_set_rate(phy->phy_ref_clk, REF_CLK_FREQ);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(phy->phy_ref_clk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(phy->apb_sys_clk);
+ if (ret)
+ goto apb_sys_fail;
+
+ ret = clk_prepare_enable(phy->apb_phy_clk);
+ if (ret)
+ goto apb_phy_fail;
+
+ ret = clk_prepare_enable(phy->pcie_aclk);
+ if (ret)
+ goto aclk_fail;
+
+ ret = clk_prepare_enable(phy->pcie_aux_clk);
+ if (ret)
+ goto aux_clk_fail;
+
+ return 0;
+
+close_clk:
+ clk_disable_unprepare(phy->pcie_aux_clk);
+aux_clk_fail:
+ clk_disable_unprepare(phy->pcie_aclk);
+aclk_fail:
+ clk_disable_unprepare(phy->apb_phy_clk);
+apb_phy_fail:
+ clk_disable_unprepare(phy->apb_sys_clk);
+apb_sys_fail:
+ clk_disable_unprepare(phy->phy_ref_clk);
+
+ return ret;
+}
+
+static int hi3660_pcie_phy_power_on(struct phy *generic_phy)
+{
+ struct hi3660_pcie_phy *phy = phy_get_drvdata(generic_phy);
+ struct device *dev = phy->dev;
+ u32 reg_val;
+ int ret;
+
+ /* Power supply for Host */
+ regmap_write(phy->sysctrl,
+ SCTRL_PCIE_CMOS_OFFSET, SCTRL_PCIE_CMOS_BIT);
+ usleep_range(TIME_CMOS_MIN, TIME_CMOS_MAX);
+
+ hi3660_pcie_phy_oe_enable(phy);
+
+ ret = kirin_pcie_clk_ctrl(phy, true);
+ if (ret)
+ return ret;
+
+ /* ISO disable, PCIeCtrl, PHY assert and clk gate clear */
+ regmap_write(phy->sysctrl,
+ SCTRL_PCIE_ISO_OFFSET, SCTRL_PCIE_ISO_BIT);
+ regmap_write(phy->crgctrl,
+ CRGCTRL_PCIE_ASSERT_OFFSET, CRGCTRL_PCIE_ASSERT_BIT);
+ regmap_write(phy->sysctrl,
+ SCTRL_PCIE_HPCLK_OFFSET, SCTRL_PCIE_HPCLK_BIT);
+
+ reg_val = kirin_apb_phy_readl(phy, PCIE_APB_PHY_CTRL1);
+ reg_val &= ~PHY_REF_PAD_BIT;
+ kirin_apb_phy_writel(phy, reg_val, PCIE_APB_PHY_CTRL1);
+
+ reg_val = kirin_apb_phy_readl(phy, PCIE_APB_PHY_CTRL0);
+ reg_val &= ~PHY_PWR_DOWN_BIT;
+ kirin_apb_phy_writel(phy, reg_val, PCIE_APB_PHY_CTRL0);
+ usleep_range(TIME_PHY_PD_MIN, TIME_PHY_PD_MAX);
+
+ reg_val = kirin_apb_phy_readl(phy, PCIE_APB_PHY_CTRL1);
+ reg_val &= ~PHY_RST_ACK_BIT;
+ kirin_apb_phy_writel(phy, reg_val, PCIE_APB_PHY_CTRL1);
+
+ usleep_range(PIPE_CLK_WAIT_MIN, PIPE_CLK_WAIT_MAX);
+ reg_val = kirin_apb_phy_readl(phy, PCIE_APB_PHY_STATUS0);
+ if (reg_val & PIPE_CLK_STABLE) {
+ dev_err(dev, "PIPE clk is not stable\n");
+ ret = -EINVAL;
+ goto disable_clks;
+ }
+
+ /* perst assert Endpoint */
+ if (!gpio_request(phy->gpio_id_reset, "pcie_perst")) {
+ usleep_range(REF_2_PERST_MIN, REF_2_PERST_MAX);
+ ret = gpio_direction_output(phy->gpio_id_reset, 1);
+ if (ret)
+ goto disable_clks;
+ usleep_range(PERST_2_ACCESS_MIN, PERST_2_ACCESS_MAX);
+ return 0;
+ }
+
+disable_clks:
+ kirin_pcie_clk_ctrl(phy, false);
+ return ret;
+}
+
+static int hi3660_pcie_phy_power_off(struct phy *generic_phy)
+{
+ struct hi3660_pcie_phy *phy = phy_get_drvdata(generic_phy);
+
+ /* Drop power supply for Host */
+ regmap_write(phy->sysctrl, SCTRL_PCIE_CMOS_OFFSET, 0x00);
+
+ kirin_pcie_clk_ctrl(phy, false);
+
+ return 0;
+}
+
+static const struct phy_ops hi3660_phy_ops = {
+ .power_on = hi3660_pcie_phy_power_on,
+ .power_off = hi3660_pcie_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int kirin_pcie_get_resources(struct hi3660_pcie_phy *phy,
+ struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+
+ /* syscon */
+ phy->crgctrl = syscon_regmap_lookup_by_compatible("hisilicon,hi3660-crgctrl");
+ if (IS_ERR(phy->crgctrl))
+ return PTR_ERR(phy->crgctrl);
+
+ phy->sysctrl = syscon_regmap_lookup_by_compatible("hisilicon,hi3660-sctrl");
+ if (IS_ERR(phy->sysctrl))
+ return PTR_ERR(phy->sysctrl);
+
+ /* clocks */
+ phy->phy_ref_clk = devm_clk_get(dev, "pcie_phy_ref");
+ if (IS_ERR(phy->phy_ref_clk))
+ return PTR_ERR(phy->phy_ref_clk);
+
+ phy->pcie_aux_clk = devm_clk_get(dev, "pcie_aux");
+ if (IS_ERR(phy->pcie_aux_clk))
+ return PTR_ERR(phy->pcie_aux_clk);
+
+ phy->apb_phy_clk = devm_clk_get(dev, "pcie_apb_phy");
+ if (IS_ERR(phy->apb_phy_clk))
+ return PTR_ERR(phy->apb_phy_clk);
+
+ phy->apb_sys_clk = devm_clk_get(dev, "pcie_apb_sys");
+ if (IS_ERR(phy->apb_sys_clk))
+ return PTR_ERR(phy->apb_sys_clk);
+
+ phy->pcie_aclk = devm_clk_get(dev, "pcie_aclk");
+ if (IS_ERR(phy->pcie_aclk))
+ return PTR_ERR(phy->pcie_aclk);
+
+ /* registers */
+ phy->base = devm_platform_ioremap_resource_byname(pdev, "phy");
+ if (IS_ERR(phy->base))
+ return PTR_ERR(phy->base);
+
+ /* gpios */
+ phy->gpio_id_reset = of_get_named_gpio(dev->of_node,
+ "reset-gpios", 0);
+ if (phy->gpio_id_reset == -EPROBE_DEFER) {
+ return -EPROBE_DEFER;
+ } else if (!gpio_is_valid(phy->gpio_id_reset)) {
+ dev_err(dev, "unable to get a valid gpio pin\n");
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int hi3660_pcie_phy_probe(struct platform_device *pdev)
+{
+ struct phy_provider *phy_provider;
+ struct device *dev = &pdev->dev;
+ struct hi3660_pcie_phy *phy;
+ struct phy *generic_phy;
+ int ret;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ phy->dev = dev;
+
+ ret = kirin_pcie_get_resources(phy, pdev);
+ if (ret)
+ return ret;
+
+ generic_phy = devm_phy_create(dev, dev->of_node, &hi3660_phy_ops);
+ if (IS_ERR(generic_phy)) {
+ dev_err(dev, "failed to create PHY\n");
+ return PTR_ERR(generic_phy);
+ }
+
+ phy_set_drvdata(generic_phy, phy);
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id hi3660_pcie_phy_match[] = {
+ {
+ .compatible = "hisilicon,hi960-pcie-phy",
+ },
+ {},
+};
+
+static struct platform_driver hi3660_pcie_phy_driver = {
+ .probe = hi3660_pcie_phy_probe,
+ .driver = {
+ .of_match_table = hi3660_pcie_phy_match,
+ .name = "hi3660_pcie_phy",
+ .suppress_bind_attrs = true,
+ }
+};
+builtin_platform_driver(hi3660_pcie_phy_driver);
--
2.31.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 5/8] phy: HiSilicon: Add driver for Kirin 960 PCIe PHY
@ 2021-07-12 21:46 ` Mauro Carvalho Chehab
0 siblings, 0 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-12 21:46 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
Manivannan Sadhasivam, Rob Herring, Greg Kroah-Hartman,
Kishon Vijay Abraham I, Vinod Koul, linux-kernel, linux-phy
The pcie-kirin PCIe driver contains internally a PHY interface for
a Kirin 960. As we'll be adding support also for Kirin 970 PHY, we
need to first split the PHY into a separate driver.
So, add a new driver with just the PHY part of
drivers/pci/controller/dwc/pcie-kirin.c.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
drivers/phy/hisilicon/Kconfig | 10 +
drivers/phy/hisilicon/Makefile | 1 +
drivers/phy/hisilicon/phy-hi3660-pcie.c | 325 ++++++++++++++++++++++++
3 files changed, 336 insertions(+)
create mode 100644 drivers/phy/hisilicon/phy-hi3660-pcie.c
diff --git a/drivers/phy/hisilicon/Kconfig b/drivers/phy/hisilicon/Kconfig
index 4d008cfc279c..30b7f1187965 100644
--- a/drivers/phy/hisilicon/Kconfig
+++ b/drivers/phy/hisilicon/Kconfig
@@ -23,6 +23,16 @@ config PHY_HI3660_USB
To compile this driver as a module, choose M here.
+config PHY_HI3660_PCIE
+ tristate "hi3660 PCIe PHY support"
+ depends on (ARCH_HISI && ARM64) || COMPILE_TEST
+ select GENERIC_PHY
+ select MFD_SYSCON
+ help
+ Enable this to support the HiSilicon hi3660 PCIe PHY.
+
+ To compile this driver as a module, choose M here.
+
config PHY_HI3670_USB
tristate "hi3670 USB PHY support"
depends on (ARCH_HISI && ARM64) || COMPILE_TEST
diff --git a/drivers/phy/hisilicon/Makefile b/drivers/phy/hisilicon/Makefile
index 51729868145b..3c3d70dd7469 100644
--- a/drivers/phy/hisilicon/Makefile
+++ b/drivers/phy/hisilicon/Makefile
@@ -1,6 +1,7 @@
# SPDX-License-Identifier: GPL-2.0-only
obj-$(CONFIG_PHY_HI6220_USB) += phy-hi6220-usb.o
obj-$(CONFIG_PHY_HI3660_USB) += phy-hi3660-usb3.o
+obj-$(CONFIG_PHY_HI3660_PCIE) += phy-hi3660-pcie.o
obj-$(CONFIG_PHY_HI3670_USB) += phy-hi3670-usb3.o
obj-$(CONFIG_PHY_HISTB_COMBPHY) += phy-histb-combphy.o
obj-$(CONFIG_PHY_HISI_INNO_USB2) += phy-hisi-inno-usb2.o
diff --git a/drivers/phy/hisilicon/phy-hi3660-pcie.c b/drivers/phy/hisilicon/phy-hi3660-pcie.c
new file mode 100644
index 000000000000..130314b0e8cb
--- /dev/null
+++ b/drivers/phy/hisilicon/phy-hi3660-pcie.c
@@ -0,0 +1,325 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * PCIe phy driver for Kirin 960
+ *
+ * Copyright (C) 2017 HiSilicon Electronics Co., Ltd.
+ * https://www.huawei.com
+ *
+ * Copyright (C) 2021 Huawei Electronics Co., Ltd.
+ * https://www.huawei.com
+ *
+ * Author:
+ * Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
+ */
+
+#include <linux/clk.h>
+#include <linux/gpio.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define REF_CLK_FREQ 100000000
+
+/* info located in APB PHY */
+#define PCIE_APB_PHY_CTRL0 0x0
+#define PCIE_APB_PHY_CTRL1 0x4
+#define PCIE_APB_PHY_STATUS0 0x400
+#define PIPE_CLK_STABLE BIT(19)
+#define PHY_REF_PAD_BIT BIT(8)
+#define PHY_PWR_DOWN_BIT BIT(22)
+#define PHY_RST_ACK_BIT BIT(16)
+
+/* info located in sysctrl */
+#define SCTRL_PCIE_CMOS_OFFSET 0x60
+#define SCTRL_PCIE_CMOS_BIT 0x10
+#define SCTRL_PCIE_ISO_OFFSET 0x44
+#define SCTRL_PCIE_ISO_BIT 0x30
+#define SCTRL_PCIE_HPCLK_OFFSET 0x190
+#define SCTRL_PCIE_HPCLK_BIT 0x184000
+#define SCTRL_PCIE_OE_OFFSET 0x14a
+#define PCIE_DEBOUNCE_PARAM 0xF0F400
+#define PCIE_OE_BYPASS (0x3 << 28)
+
+/* peri_crg ctrl */
+#define CRGCTRL_PCIE_ASSERT_OFFSET 0x88
+#define CRGCTRL_PCIE_ASSERT_BIT 0x8c000000
+
+/* Time for delay */
+#define REF_2_PERST_MIN 20000
+#define REF_2_PERST_MAX 25000
+#define PERST_2_ACCESS_MIN 10000
+#define PERST_2_ACCESS_MAX 12000
+#define PIPE_CLK_WAIT_MIN 550
+#define PIPE_CLK_WAIT_MAX 600
+#define TIME_CMOS_MIN 100
+#define TIME_CMOS_MAX 105
+#define TIME_PHY_PD_MIN 10
+#define TIME_PHY_PD_MAX 11
+
+struct hi3660_pcie_phy {
+ struct device *dev;
+ void __iomem *base;
+ struct regmap *crgctrl;
+ struct regmap *sysctrl;
+ struct clk *apb_sys_clk;
+ struct clk *apb_phy_clk;
+ struct clk *phy_ref_clk;
+ struct clk *pcie_aclk;
+ struct clk *pcie_aux_clk;
+ int gpio_id_reset;
+};
+
+/* Registers in PCIePHY */
+static inline void kirin_apb_phy_writel(struct hi3660_pcie_phy *hi3660_pcie_phy,
+ u32 val, u32 reg)
+{
+ writel(val, hi3660_pcie_phy->base + reg);
+}
+
+static inline u32 kirin_apb_phy_readl(struct hi3660_pcie_phy *hi3660_pcie_phy,
+ u32 reg)
+{
+ return readl(hi3660_pcie_phy->base + reg);
+}
+
+static void hi3660_pcie_phy_oe_enable(struct hi3660_pcie_phy *phy)
+{
+ u32 val;
+
+ regmap_read(phy->sysctrl, SCTRL_PCIE_OE_OFFSET, &val);
+ val |= PCIE_DEBOUNCE_PARAM;
+ val &= ~PCIE_OE_BYPASS;
+ regmap_write(phy->sysctrl, SCTRL_PCIE_OE_OFFSET, val);
+}
+
+
+static int kirin_pcie_clk_ctrl(struct hi3660_pcie_phy *phy, bool enable)
+{
+ int ret = 0;
+
+ if (!enable)
+ goto close_clk;
+
+ ret = clk_set_rate(phy->phy_ref_clk, REF_CLK_FREQ);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(phy->phy_ref_clk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(phy->apb_sys_clk);
+ if (ret)
+ goto apb_sys_fail;
+
+ ret = clk_prepare_enable(phy->apb_phy_clk);
+ if (ret)
+ goto apb_phy_fail;
+
+ ret = clk_prepare_enable(phy->pcie_aclk);
+ if (ret)
+ goto aclk_fail;
+
+ ret = clk_prepare_enable(phy->pcie_aux_clk);
+ if (ret)
+ goto aux_clk_fail;
+
+ return 0;
+
+close_clk:
+ clk_disable_unprepare(phy->pcie_aux_clk);
+aux_clk_fail:
+ clk_disable_unprepare(phy->pcie_aclk);
+aclk_fail:
+ clk_disable_unprepare(phy->apb_phy_clk);
+apb_phy_fail:
+ clk_disable_unprepare(phy->apb_sys_clk);
+apb_sys_fail:
+ clk_disable_unprepare(phy->phy_ref_clk);
+
+ return ret;
+}
+
+static int hi3660_pcie_phy_power_on(struct phy *generic_phy)
+{
+ struct hi3660_pcie_phy *phy = phy_get_drvdata(generic_phy);
+ struct device *dev = phy->dev;
+ u32 reg_val;
+ int ret;
+
+ /* Power supply for Host */
+ regmap_write(phy->sysctrl,
+ SCTRL_PCIE_CMOS_OFFSET, SCTRL_PCIE_CMOS_BIT);
+ usleep_range(TIME_CMOS_MIN, TIME_CMOS_MAX);
+
+ hi3660_pcie_phy_oe_enable(phy);
+
+ ret = kirin_pcie_clk_ctrl(phy, true);
+ if (ret)
+ return ret;
+
+ /* ISO disable, PCIeCtrl, PHY assert and clk gate clear */
+ regmap_write(phy->sysctrl,
+ SCTRL_PCIE_ISO_OFFSET, SCTRL_PCIE_ISO_BIT);
+ regmap_write(phy->crgctrl,
+ CRGCTRL_PCIE_ASSERT_OFFSET, CRGCTRL_PCIE_ASSERT_BIT);
+ regmap_write(phy->sysctrl,
+ SCTRL_PCIE_HPCLK_OFFSET, SCTRL_PCIE_HPCLK_BIT);
+
+ reg_val = kirin_apb_phy_readl(phy, PCIE_APB_PHY_CTRL1);
+ reg_val &= ~PHY_REF_PAD_BIT;
+ kirin_apb_phy_writel(phy, reg_val, PCIE_APB_PHY_CTRL1);
+
+ reg_val = kirin_apb_phy_readl(phy, PCIE_APB_PHY_CTRL0);
+ reg_val &= ~PHY_PWR_DOWN_BIT;
+ kirin_apb_phy_writel(phy, reg_val, PCIE_APB_PHY_CTRL0);
+ usleep_range(TIME_PHY_PD_MIN, TIME_PHY_PD_MAX);
+
+ reg_val = kirin_apb_phy_readl(phy, PCIE_APB_PHY_CTRL1);
+ reg_val &= ~PHY_RST_ACK_BIT;
+ kirin_apb_phy_writel(phy, reg_val, PCIE_APB_PHY_CTRL1);
+
+ usleep_range(PIPE_CLK_WAIT_MIN, PIPE_CLK_WAIT_MAX);
+ reg_val = kirin_apb_phy_readl(phy, PCIE_APB_PHY_STATUS0);
+ if (reg_val & PIPE_CLK_STABLE) {
+ dev_err(dev, "PIPE clk is not stable\n");
+ ret = -EINVAL;
+ goto disable_clks;
+ }
+
+ /* perst assert Endpoint */
+ if (!gpio_request(phy->gpio_id_reset, "pcie_perst")) {
+ usleep_range(REF_2_PERST_MIN, REF_2_PERST_MAX);
+ ret = gpio_direction_output(phy->gpio_id_reset, 1);
+ if (ret)
+ goto disable_clks;
+ usleep_range(PERST_2_ACCESS_MIN, PERST_2_ACCESS_MAX);
+ return 0;
+ }
+
+disable_clks:
+ kirin_pcie_clk_ctrl(phy, false);
+ return ret;
+}
+
+static int hi3660_pcie_phy_power_off(struct phy *generic_phy)
+{
+ struct hi3660_pcie_phy *phy = phy_get_drvdata(generic_phy);
+
+ /* Drop power supply for Host */
+ regmap_write(phy->sysctrl, SCTRL_PCIE_CMOS_OFFSET, 0x00);
+
+ kirin_pcie_clk_ctrl(phy, false);
+
+ return 0;
+}
+
+static const struct phy_ops hi3660_phy_ops = {
+ .power_on = hi3660_pcie_phy_power_on,
+ .power_off = hi3660_pcie_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int kirin_pcie_get_resources(struct hi3660_pcie_phy *phy,
+ struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+
+ /* syscon */
+ phy->crgctrl = syscon_regmap_lookup_by_compatible("hisilicon,hi3660-crgctrl");
+ if (IS_ERR(phy->crgctrl))
+ return PTR_ERR(phy->crgctrl);
+
+ phy->sysctrl = syscon_regmap_lookup_by_compatible("hisilicon,hi3660-sctrl");
+ if (IS_ERR(phy->sysctrl))
+ return PTR_ERR(phy->sysctrl);
+
+ /* clocks */
+ phy->phy_ref_clk = devm_clk_get(dev, "pcie_phy_ref");
+ if (IS_ERR(phy->phy_ref_clk))
+ return PTR_ERR(phy->phy_ref_clk);
+
+ phy->pcie_aux_clk = devm_clk_get(dev, "pcie_aux");
+ if (IS_ERR(phy->pcie_aux_clk))
+ return PTR_ERR(phy->pcie_aux_clk);
+
+ phy->apb_phy_clk = devm_clk_get(dev, "pcie_apb_phy");
+ if (IS_ERR(phy->apb_phy_clk))
+ return PTR_ERR(phy->apb_phy_clk);
+
+ phy->apb_sys_clk = devm_clk_get(dev, "pcie_apb_sys");
+ if (IS_ERR(phy->apb_sys_clk))
+ return PTR_ERR(phy->apb_sys_clk);
+
+ phy->pcie_aclk = devm_clk_get(dev, "pcie_aclk");
+ if (IS_ERR(phy->pcie_aclk))
+ return PTR_ERR(phy->pcie_aclk);
+
+ /* registers */
+ phy->base = devm_platform_ioremap_resource_byname(pdev, "phy");
+ if (IS_ERR(phy->base))
+ return PTR_ERR(phy->base);
+
+ /* gpios */
+ phy->gpio_id_reset = of_get_named_gpio(dev->of_node,
+ "reset-gpios", 0);
+ if (phy->gpio_id_reset == -EPROBE_DEFER) {
+ return -EPROBE_DEFER;
+ } else if (!gpio_is_valid(phy->gpio_id_reset)) {
+ dev_err(dev, "unable to get a valid gpio pin\n");
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int hi3660_pcie_phy_probe(struct platform_device *pdev)
+{
+ struct phy_provider *phy_provider;
+ struct device *dev = &pdev->dev;
+ struct hi3660_pcie_phy *phy;
+ struct phy *generic_phy;
+ int ret;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ phy->dev = dev;
+
+ ret = kirin_pcie_get_resources(phy, pdev);
+ if (ret)
+ return ret;
+
+ generic_phy = devm_phy_create(dev, dev->of_node, &hi3660_phy_ops);
+ if (IS_ERR(generic_phy)) {
+ dev_err(dev, "failed to create PHY\n");
+ return PTR_ERR(generic_phy);
+ }
+
+ phy_set_drvdata(generic_phy, phy);
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id hi3660_pcie_phy_match[] = {
+ {
+ .compatible = "hisilicon,hi960-pcie-phy",
+ },
+ {},
+};
+
+static struct platform_driver hi3660_pcie_phy_driver = {
+ .probe = hi3660_pcie_phy_probe,
+ .driver = {
+ .of_match_table = hi3660_pcie_phy_match,
+ .name = "hi3660_pcie_phy",
+ .suppress_bind_attrs = true,
+ }
+};
+builtin_platform_driver(hi3660_pcie_phy_driver);
--
2.31.1
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 6/8] phy: HiSilicon: add driver for Kirin 970 PCIe PHY
2021-07-12 21:46 ` Mauro Carvalho Chehab
@ 2021-07-12 21:46 ` Mauro Carvalho Chehab
-1 siblings, 0 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-12 21:46 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
Krzysztof Wilczyński, Manivannan Sadhasivam, Rob Herring,
Binghui Wang, Bjorn Helgaas, Greg Kroah-Hartman,
Kishon Vijay Abraham I, Lorenzo Pieralisi, Rob Herring,
Vinod Koul, Xiaowei Song, devicetree, linux-kernel, linux-pci,
linux-phy
The Kirin 970 PHY is somewhat similar to the Kirin 960, but it
does a lot more. Add the needed bits for PCIe to start working on
HiKey 970 boards.
Co-developed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
.../devicetree/bindings/pci/kirin-pcie.txt | 1 +
drivers/pci/controller/dwc/pcie-kirin.c | 1 +
drivers/phy/hisilicon/Kconfig | 10 +
drivers/phy/hisilicon/Makefile | 1 +
drivers/phy/hisilicon/phy-hi3670-pcie.c | 892 ++++++++++++++++++
5 files changed, 905 insertions(+)
create mode 100644 drivers/phy/hisilicon/phy-hi3670-pcie.c
diff --git a/Documentation/devicetree/bindings/pci/kirin-pcie.txt b/Documentation/devicetree/bindings/pci/kirin-pcie.txt
index a93a8cfa1afb..585aadfeafd1 100644
--- a/Documentation/devicetree/bindings/pci/kirin-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/kirin-pcie.txt
@@ -10,6 +10,7 @@ Additional properties are described here:
Required properties
- compatible:
"hisilicon,kirin960-pcie"
+ "hisilicon,kirin970-pcie"
- reg: Should contain rc_dbi, apb, config registers location and length.
- reg-names: Must include the following entries:
"dbi": controller configuration registers;
diff --git a/drivers/pci/controller/dwc/pcie-kirin.c b/drivers/pci/controller/dwc/pcie-kirin.c
index 026fd1e42a55..7b0f87535960 100644
--- a/drivers/pci/controller/dwc/pcie-kirin.c
+++ b/drivers/pci/controller/dwc/pcie-kirin.c
@@ -472,6 +472,7 @@ static int kirin_pcie_probe(struct platform_device *pdev)
static const struct of_device_id kirin_pcie_match[] = {
{ .compatible = "hisilicon,kirin960-pcie" },
+ { .compatible = "hisilicon,kirin970-pcie" },
{},
};
diff --git a/drivers/phy/hisilicon/Kconfig b/drivers/phy/hisilicon/Kconfig
index 30b7f1187965..65e0ff6e85ad 100644
--- a/drivers/phy/hisilicon/Kconfig
+++ b/drivers/phy/hisilicon/Kconfig
@@ -43,6 +43,16 @@ config PHY_HI3670_USB
To compile this driver as a module, choose M here.
+config PHY_HI3670_PCIE
+ tristate "hi3670 PCIe PHY support"
+ depends on (ARCH_HISI && ARM64) || COMPILE_TEST
+ select GENERIC_PHY
+ select MFD_SYSCON
+ help
+ Enable this to support the HiSilicon hi3670 PCIe PHY.
+
+ To compile this driver as a module, choose M here.
+
config PHY_HISTB_COMBPHY
tristate "HiSilicon STB SoCs COMBPHY support"
depends on (ARCH_HISI && ARM64) || COMPILE_TEST
diff --git a/drivers/phy/hisilicon/Makefile b/drivers/phy/hisilicon/Makefile
index 3c3d70dd7469..2670f2f382e1 100644
--- a/drivers/phy/hisilicon/Makefile
+++ b/drivers/phy/hisilicon/Makefile
@@ -3,6 +3,7 @@ obj-$(CONFIG_PHY_HI6220_USB) += phy-hi6220-usb.o
obj-$(CONFIG_PHY_HI3660_USB) += phy-hi3660-usb3.o
obj-$(CONFIG_PHY_HI3660_PCIE) += phy-hi3660-pcie.o
obj-$(CONFIG_PHY_HI3670_USB) += phy-hi3670-usb3.o
+obj-$(CONFIG_PHY_HI3670_PCIE) += phy-hi3670-pcie.o
obj-$(CONFIG_PHY_HISTB_COMBPHY) += phy-histb-combphy.o
obj-$(CONFIG_PHY_HISI_INNO_USB2) += phy-hisi-inno-usb2.o
obj-$(CONFIG_PHY_HIX5HD2_SATA) += phy-hix5hd2-sata.o
diff --git a/drivers/phy/hisilicon/phy-hi3670-pcie.c b/drivers/phy/hisilicon/phy-hi3670-pcie.c
new file mode 100644
index 000000000000..dcbf7d47d8e7
--- /dev/null
+++ b/drivers/phy/hisilicon/phy-hi3670-pcie.c
@@ -0,0 +1,892 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * PCIe phy driver for Kirin 970
+ *
+ * Copyright (C) 2017 HiSilicon Electronics Co., Ltd.
+ * https://www.huawei.com
+ * Copyright (C) 2021 Huawei Technologies Co., Ltd.
+ * https://www.huawei.com
+ *
+ * Authors:
+ * Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
+ * Manivannan Sadhasivam <mani@kernel.org>
+ *
+ * Based on:
+ * https://lore.kernel.org/lkml/4c9d6581478aa966698758c0420933f5defab4dd.1612335031.git.mchehab+huawei@kernel.org/
+ */
+
+#include <linux/clk.h>
+#include <linux/gpio.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define AXI_CLK_FREQ 207500000
+#define REF_CLK_FREQ 100000000
+
+/* PCIe CTRL registers */
+#define SOC_PCIECTRL_CTRL0_ADDR 0x000
+#define SOC_PCIECTRL_CTRL1_ADDR 0x004
+#define SOC_PCIECTRL_CTRL7_ADDR 0x01c
+#define SOC_PCIECTRL_CTRL12_ADDR 0x030
+#define SOC_PCIECTRL_CTRL20_ADDR 0x050
+#define SOC_PCIECTRL_CTRL21_ADDR 0x054
+#define SOC_PCIECTRL_STATE0_ADDR 0x400
+
+/* PCIe PHY registers */
+#define SOC_PCIEPHY_CTRL0_ADDR 0x000
+#define SOC_PCIEPHY_CTRL1_ADDR 0x004
+#define SOC_PCIEPHY_CTRL2_ADDR 0x008
+#define SOC_PCIEPHY_CTRL3_ADDR 0x00c
+#define SOC_PCIEPHY_CTRL38_ADDR 0x0098
+#define SOC_PCIEPHY_STATE0_ADDR 0x400
+
+#define PCIE_LINKUP_ENABLE (0x8020)
+#define PCIE_ELBI_SLV_DBI_ENABLE (0x1 << 21)
+#define PCIE_LTSSM_ENABLE_BIT (0x1 << 11)
+#define PCIEPHY_RESET_BIT (0x1 << 17)
+#define PCIEPHY_PIPE_LINE0_RESET_BIT (0x1 << 19)
+
+#define PORT_MSI_CTRL_ADDR 0x820
+#define PORT_MSI_CTRL_UPPER_ADDR 0x824
+#define PORT_MSI_CTRL_INT0_ENABLE 0x828
+
+#define EYEPARAM_NOCFG 0xFFFFFFFF
+#define RAWLANEN_DIG_PCS_XF_TX_OVRD_IN_1 0x3001
+#define SUP_DIG_LVL_OVRD_IN 0xf
+#define LANEN_DIG_ASIC_TX_OVRD_IN_1 0x1002
+#define LANEN_DIG_ASIC_TX_OVRD_IN_2 0x1003
+
+/* hi3670 pciephy register */
+#define SOC_PCIEPHY_MMC1PLL_CTRL1 0xc04
+#define SOC_PCIEPHY_MMC1PLL_CTRL16 0xC40
+#define SOC_PCIEPHY_MMC1PLL_CTRL17 0xC44
+#define SOC_PCIEPHY_MMC1PLL_CTRL20 0xC50
+#define SOC_PCIEPHY_MMC1PLL_CTRL21 0xC54
+#define SOC_PCIEPHY_MMC1PLL_STAT0 0xE00
+
+#define CRGPERIPH_PEREN12 0x470
+#define CRGPERIPH_PERDIS12 0x474
+#define CRGPERIPH_PCIECTRL0 0x800
+
+/* define ie,oe cfg */
+#define IO_IE_EN_HARD_BYPASS (0x1 << 27)
+#define IO_OE_EN_HARD_BYPASS (0x1 << 11)
+#define IO_HARD_CTRL_DEBOUNCE_BYPASS (0x1 << 10)
+#define IO_OE_GT_MODE (0x2 << 7)
+#define DEBOUNCE_WAITCFG_IN (0xf << 20)
+#define DEBOUNCE_WAITCFG_OUT (0xf << 13)
+
+/* noc power domain */
+#define NOC_POWER_IDLEREQ_1 0x38c
+#define NOC_POWER_IDLE_1 0x394
+#define NOC_PW_MASK 0x10000
+#define NOC_PW_SET_BIT 0x1
+
+/* Number of GPIOs required by PHY */
+#define MAX_GPIO_RESETS 4
+#define MAX_GPIO_CLKREQ 3
+#define NUM_EYEPARAM 5
+
+/* info located in sysctrl */
+#define SCTRL_PCIE_CMOS_OFFSET 0x60
+#define SCTRL_PCIE_CMOS_BIT 0x10
+#define SCTRL_PCIE_ISO_OFFSET 0x44
+#define SCTRL_PCIE_ISO_BIT 0x30
+#define SCTRL_PCIE_HPCLK_OFFSET 0x190
+#define SCTRL_PCIE_HPCLK_BIT 0x184000
+#define SCTRL_PCIE_OE_OFFSET 0x14a
+#define PCIE_DEBOUNCE_PARAM 0xF0F400
+#define PCIE_OE_BYPASS (0x3 << 28)
+
+/* peri_crg ctrl */
+#define CRGCTRL_PCIE_ASSERT_OFFSET 0x88
+#define CRGCTRL_PCIE_ASSERT_BIT 0x8c000000
+
+/* Time for delay */
+#define REF_2_PERST_MIN 20000
+#define REF_2_PERST_MAX 25000
+#define PERST_2_ACCESS_MIN 10000
+#define PERST_2_ACCESS_MAX 12000
+#define PIPE_CLK_WAIT_MIN 550
+#define PIPE_CLK_WAIT_MAX 600
+#define TIME_CMOS_MIN 100
+#define TIME_CMOS_MAX 105
+#define TIME_PHY_PD_MIN 10
+#define TIME_PHY_PD_MAX 11
+
+struct hi3670_pcie_phy {
+ struct device *dev;
+ void __iomem *base;
+ struct regmap *apb;
+ struct regmap *crgctrl;
+ struct regmap *sysctrl;
+ struct regmap *pmctrl;
+ struct clk *apb_sys_clk;
+ struct clk *apb_phy_clk;
+ struct clk *phy_ref_clk;
+ struct clk *pcie_aclk;
+ struct clk *pcie_aux_clk;
+ int n_gpio_resets;
+ int n_gpio_clkreq;
+ int gpio_id_reset[MAX_GPIO_RESETS];
+ const char *reset_names[MAX_GPIO_RESETS];
+ int gpio_id_clkreq[MAX_GPIO_CLKREQ];
+ const char *clkreq_names[MAX_GPIO_CLKREQ];
+ u32 eye_param[NUM_EYEPARAM];
+};
+
+
+/* Registers in PCIePHY */
+static inline void hi3670_apb_phy_writel(struct hi3670_pcie_phy *phy,
+ u32 val, u32 reg)
+{
+ writel(val, phy->base + 0x40000 + reg);
+}
+
+static inline u32 hi3670_apb_phy_readl(struct hi3670_pcie_phy *phy, u32 reg)
+{
+ return readl(phy->base + 0x40000 + reg);
+}
+
+static inline void kirin_apb_natural_phy_writel(struct hi3670_pcie_phy *phy,
+ u32 val, u32 reg)
+{
+ writel(val, phy->base + reg * 4);
+}
+
+static inline u32 kirin_apb_natural_phy_readl(struct hi3670_pcie_phy *phy,
+ u32 reg)
+{
+ return readl(phy->base + reg * 4);
+}
+
+static void hi3670_pcie_phy_oe_enable(struct hi3670_pcie_phy *phy)
+{
+ u32 val;
+
+ regmap_read(phy->sysctrl, SCTRL_PCIE_OE_OFFSET, &val);
+ val |= PCIE_DEBOUNCE_PARAM;
+ val &= ~PCIE_OE_BYPASS;
+ regmap_write(phy->sysctrl, SCTRL_PCIE_OE_OFFSET, val);
+}
+
+void hi3670_pcie_get_eyeparam(struct hi3670_pcie_phy *phy)
+{
+ struct device *dev = phy->dev;
+ struct device_node *np;
+ int ret, i;
+
+ np = dev->of_node;
+
+ ret = of_property_read_u32_array(np, "hisilicon,eye-diagram-param",
+ phy->eye_param, NUM_EYEPARAM);
+ if (!ret)
+ return;
+
+ /* There's no optional eye_param property. Set array to default */
+ for (i = 0; i < NUM_EYEPARAM; i++)
+ phy->eye_param[i] = EYEPARAM_NOCFG;
+}
+
+static void hi3670_pcie_set_eyeparam(struct hi3670_pcie_phy *phy)
+{
+ u32 val;
+
+ val = kirin_apb_natural_phy_readl(phy, RAWLANEN_DIG_PCS_XF_TX_OVRD_IN_1);
+
+ if (phy->eye_param[1] != EYEPARAM_NOCFG) {
+ val &= (~0xf00);
+ val |= (phy->eye_param[1] << 8) | (0x1 << 12);
+ }
+ kirin_apb_natural_phy_writel(phy, val, RAWLANEN_DIG_PCS_XF_TX_OVRD_IN_1);
+
+ val = kirin_apb_natural_phy_readl(phy, LANEN_DIG_ASIC_TX_OVRD_IN_2);
+ val &= (~0x1FBF);
+ if (phy->eye_param[2] != EYEPARAM_NOCFG)
+ val |= (phy->eye_param[2]<< 0) | (0x1 << 6);
+
+ if (phy->eye_param[3] != EYEPARAM_NOCFG)
+ val |= (phy->eye_param[3] << 7) | (0x1 << 13);
+
+ kirin_apb_natural_phy_writel(phy, val, LANEN_DIG_ASIC_TX_OVRD_IN_2);
+
+ val = kirin_apb_natural_phy_readl(phy, SUP_DIG_LVL_OVRD_IN);
+ if (phy->eye_param[0] != EYEPARAM_NOCFG) {
+ val &= (~0x1C0);
+ val |= (phy->eye_param[0] << 6) | (0x1 << 9);
+ }
+ kirin_apb_natural_phy_writel(phy, val, SUP_DIG_LVL_OVRD_IN);
+
+ val = kirin_apb_natural_phy_readl(phy, LANEN_DIG_ASIC_TX_OVRD_IN_1);
+ if (phy->eye_param[4] != EYEPARAM_NOCFG) {
+ val &= (~0x7E00);
+ val |= (phy->eye_param[4] << 9) | (0x1 << 15);
+ }
+ kirin_apb_natural_phy_writel(phy, val, LANEN_DIG_ASIC_TX_OVRD_IN_1);
+}
+
+static int hi3670_pcie_gpio_request(struct hi3670_pcie_phy *phy,
+ struct device *dev)
+{
+ int ret, i;
+
+ for (i = 0; i < phy->n_gpio_resets; i++) {
+ if (!gpio_is_valid(phy->gpio_id_reset[i])) {
+ dev_err(dev, "unable to get a valid %s gpio\n",
+ phy->reset_names[i]);
+ return -ENODEV;
+ }
+
+ ret = devm_gpio_request(dev, phy->gpio_id_reset[i],
+ phy->reset_names[i]);
+ if (ret)
+ return ret;
+ }
+
+ for (i = 0; i < phy->n_gpio_clkreq; i++) {
+ if (!gpio_is_valid(phy->gpio_id_clkreq[i])) {
+ dev_err(dev, "unable to get a valid %s gpio\n",
+ phy->clkreq_names[i]);
+ return -ENODEV;
+ }
+
+ ret = devm_gpio_request(dev, phy->gpio_id_clkreq[i],
+ phy->clkreq_names[i]);
+ if (ret)
+ return ret;
+ }
+
+ return ret;
+}
+
+static void hi3670_pcie_natural_cfg(struct hi3670_pcie_phy *phy)
+{
+ u32 val;
+
+ /* change 2p mem_ctrl */
+ regmap_write(phy->apb, SOC_PCIECTRL_CTRL20_ADDR, 0x02605550);
+
+ /* pull up sys_aux_pwr_det */
+ regmap_read(phy->apb, SOC_PCIECTRL_CTRL7_ADDR, &val);
+ val |= (0x1 << 10);
+ regmap_write(phy->apb, SOC_PCIECTRL_CTRL7_ADDR, val);
+
+ /* output, pull down */
+ regmap_read(phy->apb, SOC_PCIECTRL_CTRL12_ADDR, &val);
+ val &= ~(0x3 << 2);
+ val |= (0x1 << 1);
+ val &= ~(0x1 << 0);
+ regmap_write(phy->apb, SOC_PCIECTRL_CTRL12_ADDR, val);
+
+ /* Handle phy_reset and lane0_reset to HW */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_CTRL1_ADDR);
+ val |= PCIEPHY_RESET_BIT;
+ val &= ~PCIEPHY_PIPE_LINE0_RESET_BIT;
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_CTRL1_ADDR);
+
+ /* fix chip bug: TxDetectRx fail */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_CTRL38_ADDR);
+ val |= (0x1 << 2);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_CTRL38_ADDR);
+}
+
+static void hi3670_pcie_pll_init(struct hi3670_pcie_phy *phy)
+{
+ u32 val;
+
+ /* choose FNPLL */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL1);
+ val |= (0x1 << 27);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL1);
+
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL16);
+ val &= 0xF000FFFF;
+ /* fnpll fbdiv = 0xD0 */
+ val |= (0xd0 << 16);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL16);
+
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL17);
+ val &= 0xFF000000;
+ /* fnpll fracdiv = 0x555555 */
+ val |= (0x555555 << 0);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL17);
+
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL20);
+ val &= 0xF5FF88FF;
+ /* fnpll dll_en = 0x1 */
+ val |= (0x1 << 27);
+ /* fnpll postdiv1 = 0x5 */
+ val |= (0x5 << 8);
+ /* fnpll postdiv2 = 0x4 */
+ val |= (0x4 << 12);
+ /* fnpll pll_mode = 0x0 */
+ val &= ~(0x1 << 25);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL20);
+
+ hi3670_apb_phy_writel(phy, 0x20, SOC_PCIEPHY_MMC1PLL_CTRL21);
+}
+
+static int hi3670_pcie_pll_ctrl(struct hi3670_pcie_phy *phy, bool enable)
+{
+ struct device *dev = phy->dev;
+ u32 val;
+ int time = 200;
+
+ if (enable) {
+ /* pd = 0 */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL16);
+ val &= ~(0x1 << 0);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL16);
+
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_STAT0);
+
+ /* choose FNPLL */
+ while (!(val & 0x10)) {
+ if (!time) {
+ dev_err(dev, "wait for pll_lock timeout\n");
+ return -1;
+ }
+ time --;
+ udelay(1);
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_STAT0);
+ }
+
+ /* pciepll_bp = 0 */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL20);
+ val &= ~(0x1 << 16);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL20);
+
+ } else {
+ /* pd = 1 */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL16);
+ val |= (0x1 << 0);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL16);
+
+ /* pciepll_bp = 1 */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL20);
+ val |= (0x1 << 16);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL20);
+ }
+
+ return 0;
+}
+
+static void hi3670_pcie_hp_debounce_gt(struct hi3670_pcie_phy *phy, bool open)
+{
+ if (open)
+ /* gt_clk_pcie_hp/gt_clk_pcie_debounce open */
+ regmap_write(phy->crgctrl, CRGPERIPH_PEREN12, 0x9000);
+ else
+ /* gt_clk_pcie_hp/gt_clk_pcie_debounce close */
+ regmap_write(phy->crgctrl, CRGPERIPH_PERDIS12, 0x9000);
+}
+
+static void hi3670_pcie_phyref_gt(struct hi3670_pcie_phy *phy, bool open)
+{
+ unsigned int val;
+
+ regmap_read(phy->crgctrl, CRGPERIPH_PCIECTRL0, &val);
+
+ if (open)
+ val &= ~(0x1 << 1); //enable hard gt mode
+ else
+ val |= (0x1 << 1); //disable hard gt mode
+
+ regmap_write(phy->crgctrl, CRGPERIPH_PCIECTRL0, val);
+
+ /* disable soft gt mode */
+ regmap_write(phy->crgctrl, CRGPERIPH_PERDIS12, 0x4000);
+}
+
+static void hi3670_pcie_oe_ctrl(struct hi3670_pcie_phy *phy, bool en_flag)
+{
+ unsigned int val;
+
+ regmap_read(phy->crgctrl , CRGPERIPH_PCIECTRL0, &val);
+
+ /* set ie cfg */
+ val |= IO_IE_EN_HARD_BYPASS;
+
+ /* set oe cfg */
+ val &= ~IO_HARD_CTRL_DEBOUNCE_BYPASS;
+
+ /* set phy_debounce in&out time */
+ val |= (DEBOUNCE_WAITCFG_IN | DEBOUNCE_WAITCFG_OUT);
+
+ /* select oe_gt_mode */
+ val |= IO_OE_GT_MODE;
+
+ if (en_flag)
+ val &= ~IO_OE_EN_HARD_BYPASS;
+ else
+ val |= IO_OE_EN_HARD_BYPASS;
+
+ regmap_write(phy->crgctrl, CRGPERIPH_PCIECTRL0, val);
+}
+
+static void hi3670_pcie_ioref_gt(struct hi3670_pcie_phy *phy, bool open)
+{
+ unsigned int val;
+
+ if (open) {
+ regmap_write(phy->apb, SOC_PCIECTRL_CTRL21_ADDR, 0x20000070);
+
+ hi3670_pcie_oe_ctrl(phy, true);
+
+ /* en hard gt mode */
+ regmap_read(phy->crgctrl, CRGPERIPH_PCIECTRL0, &val);
+ val &= ~(0x1 << 0);
+ regmap_write(phy->crgctrl, CRGPERIPH_PCIECTRL0, val);
+
+ /* disable soft gt mode */
+ regmap_write(phy->crgctrl, CRGPERIPH_PERDIS12, 0x2000);
+
+ } else {
+ /* disable hard gt mode */
+ regmap_read(phy->crgctrl, CRGPERIPH_PCIECTRL0, &val);
+ val |= (0x1 << 0);
+ regmap_write(phy->crgctrl, CRGPERIPH_PCIECTRL0, val);
+
+ /* disable soft gt mode */
+ regmap_write(phy->crgctrl, CRGPERIPH_PERDIS12, 0x2000);
+
+ hi3670_pcie_oe_ctrl(phy, false);
+ }
+}
+
+static int hi3670_pcie_allclk_ctrl(struct hi3670_pcie_phy *phy, bool clk_on)
+{
+ struct device *dev = phy->dev;
+ u32 val;
+ int ret = 0;
+
+ if (!clk_on)
+ goto close_clocks;
+
+ /* choose 100MHz clk src: Bit[8]==1 pad, Bit[8]==0 pll */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_CTRL1_ADDR);
+ val &= ~(0x1 << 8);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_CTRL1_ADDR);
+
+ hi3670_pcie_pll_init(phy);
+
+ ret = hi3670_pcie_pll_ctrl(phy, true);
+ if (ret) {
+ dev_err(dev, "Failed to enable pll\n");
+ return -1;
+ }
+ hi3670_pcie_hp_debounce_gt(phy, true);
+ hi3670_pcie_phyref_gt(phy, true);
+ hi3670_pcie_ioref_gt(phy, true);
+
+ ret = clk_set_rate(phy->pcie_aclk, AXI_CLK_FREQ);
+ if (ret) {
+ dev_err(dev, "Failed to set rate\n");
+ goto close_clocks;
+ }
+
+ return 0;
+
+close_clocks:
+ hi3670_pcie_ioref_gt(phy, false);
+ hi3670_pcie_phyref_gt(phy, false);
+ hi3670_pcie_hp_debounce_gt(phy, false);
+
+ hi3670_pcie_pll_ctrl(phy, false);
+
+ return ret;
+}
+
+static bool is_pipe_clk_stable(struct hi3670_pcie_phy *phy)
+{
+ struct device *dev = phy->dev;
+ u32 val;
+ u32 time = 100;
+ u32 pipe_clk_stable = 0x1 << 19;
+
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_STATE0_ADDR);
+ while (val & pipe_clk_stable) {
+ mdelay(1);
+ if (time == 0) {
+ dev_err(dev, "PIPE clk is not stable\n");
+ return false;
+ }
+ time--;
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_STATE0_ADDR);
+ }
+
+ return true;
+}
+
+static int hi3670_pcie_noc_power(struct hi3670_pcie_phy *phy, bool enable)
+{
+ struct device *dev = phy->dev;
+ u32 time = 100;
+ unsigned int val = NOC_PW_MASK;
+ int rst;
+
+ if (enable)
+ val = NOC_PW_MASK | NOC_PW_SET_BIT;
+ else
+ val = NOC_PW_MASK;
+ rst = enable ? 1 : 0;
+
+ regmap_write(phy->pmctrl, NOC_POWER_IDLEREQ_1, val);
+
+ time = 100;
+ regmap_read(phy->pmctrl, NOC_POWER_IDLE_1, &val);
+ while((val & NOC_PW_SET_BIT) != rst) {
+ udelay(10);
+ if (!time) {
+ dev_err(dev, "Failed to reverse noc power-status\n");
+ return -1;
+ }
+ time--;
+ regmap_read(phy->pmctrl, NOC_POWER_IDLE_1, &val);
+ }
+
+ return 0;
+}
+
+static int hi3670_pcie_get_apb(struct hi3670_pcie_phy *phy)
+{
+ struct device_node *pcie_port;
+ struct device *dev = phy->dev;
+ struct device *pcie_dev;
+
+ pcie_port = of_get_child_by_name(dev->parent->of_node, "pcie");
+ if (!pcie_port) {
+ dev_err(dev, "no pcie node found in %s\n",
+ dev->parent->of_node->full_name);
+ return -ENODEV;
+ }
+
+ pcie_dev = bus_find_device_by_of_node(&platform_bus_type, pcie_port);
+ if (!pcie_dev) {
+ dev_err(dev, "Didn't find pcie device\n");
+ return -ENODEV;
+ }
+
+ /*
+ * We might just use NULL instead of the APB name, as the
+ * pcie-kirin currently registers directly just one regmap (although
+ * the DWC driver register other regmaps).
+ *
+ * Yet, it sounds safer to warrant that it will be accessing the
+ * right regmap. So, let's use the named version.
+ */
+ phy->apb = dev_get_regmap(pcie_dev, "kirin_pcie_apb");
+ if (!phy->apb) {
+ dev_err(dev, "Failed to get APB regmap\n");
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+
+static int kirin_pcie_clk_ctrl(struct hi3670_pcie_phy *phy, bool enable)
+{
+ int ret = 0;
+
+ if (!enable)
+ goto close_clk;
+
+ ret = clk_set_rate(phy->phy_ref_clk, REF_CLK_FREQ);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(phy->phy_ref_clk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(phy->apb_sys_clk);
+ if (ret)
+ goto apb_sys_fail;
+
+ ret = clk_prepare_enable(phy->apb_phy_clk);
+ if (ret)
+ goto apb_phy_fail;
+
+ ret = clk_prepare_enable(phy->pcie_aclk);
+ if (ret)
+ goto aclk_fail;
+
+ ret = clk_prepare_enable(phy->pcie_aux_clk);
+ if (ret)
+ goto aux_clk_fail;
+
+ return 0;
+
+close_clk:
+ clk_disable_unprepare(phy->pcie_aux_clk);
+aux_clk_fail:
+ clk_disable_unprepare(phy->pcie_aclk);
+aclk_fail:
+ clk_disable_unprepare(phy->apb_phy_clk);
+apb_phy_fail:
+ clk_disable_unprepare(phy->apb_sys_clk);
+apb_sys_fail:
+ clk_disable_unprepare(phy->phy_ref_clk);
+
+ return ret;
+}
+
+static int hi3670_pcie_phy_init(struct phy *generic_phy)
+{
+ struct hi3670_pcie_phy *phy = phy_get_drvdata(generic_phy);
+ struct device *dev = phy->dev;
+ int ret;
+
+ /*
+ * The code under hi3670_pcie_get_apb() need to access the
+ * DWC APB registers. So, get them from
+ * the pcie driver's regmap (see pcie-kirin regmap).
+ *
+ * Such kind of resource can only be obtained during the PCIe
+ * power_on sequence, as the code inside pcie-kirin needs to
+ * be already probed, as it needs to register the APB regmap.
+ */
+
+ ret = hi3670_pcie_get_apb(phy);
+ if (ret)
+ return ret;
+
+ /* phy regulator needs to be powered on before calling it */
+ return hi3670_pcie_gpio_request(phy, dev);
+}
+
+static int hi3670_pcie_phy_power_on(struct phy *generic_phy)
+{
+ struct hi3670_pcie_phy *phy = phy_get_drvdata(generic_phy);
+ int val, ret, i;
+
+ /* Power supply for Host */
+ regmap_write(phy->sysctrl,
+ SCTRL_PCIE_CMOS_OFFSET, SCTRL_PCIE_CMOS_BIT);
+ usleep_range(TIME_CMOS_MIN, TIME_CMOS_MAX);
+
+ hi3670_pcie_phy_oe_enable(phy);
+
+ for (i = 0; i < phy->n_gpio_clkreq; i++) {
+ ret = gpio_direction_output(phy->gpio_id_clkreq[i], 0);
+ if (ret)
+ return ret;
+ }
+
+ ret = kirin_pcie_clk_ctrl(phy, true);
+ if (ret)
+ return ret;
+
+ /* ISO disable, PCIeCtrl, PHY assert and clk gate clear */
+ regmap_write(phy->sysctrl,
+ SCTRL_PCIE_ISO_OFFSET, SCTRL_PCIE_ISO_BIT);
+ regmap_write(phy->crgctrl,
+ CRGCTRL_PCIE_ASSERT_OFFSET, CRGCTRL_PCIE_ASSERT_BIT);
+ regmap_write(phy->sysctrl,
+ SCTRL_PCIE_HPCLK_OFFSET, SCTRL_PCIE_HPCLK_BIT);
+
+ hi3670_pcie_natural_cfg(phy);
+
+ ret = hi3670_pcie_allclk_ctrl(phy, true);
+ if (ret)
+ goto disable_clks;
+
+ /* pull down phy_test_powerdown signal */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_CTRL0_ADDR);
+ val &= ~(0x1 << 22);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_CTRL0_ADDR);
+
+ /* deassert controller perst_n */
+ regmap_read(phy->apb, SOC_PCIECTRL_CTRL12_ADDR, &val);
+ val |= (0x1 << 2);
+ regmap_write(phy->apb, SOC_PCIECTRL_CTRL12_ADDR, val);
+ udelay(10);
+
+ /* perst assert Endpoints */
+ usleep_range(21000, 23000);
+ for (i = 0; i < phy->n_gpio_resets; i++) {
+ ret = gpio_direction_output(phy->gpio_id_reset[i], 1);
+ if (ret)
+ return ret;
+ }
+ usleep_range(10000, 11000);
+
+ ret = is_pipe_clk_stable(phy);
+ if (!ret)
+ goto disable_clks;
+
+ hi3670_pcie_set_eyeparam(phy);
+
+ ret = hi3670_pcie_noc_power(phy, false);
+ if (ret)
+ goto disable_clks;
+
+ return 0;
+
+disable_clks:
+ kirin_pcie_clk_ctrl(phy, false);
+ return ret;
+}
+
+static int hi3670_pcie_phy_power_off(struct phy *generic_phy)
+{
+ struct hi3670_pcie_phy *phy = phy_get_drvdata(generic_phy);
+
+ /* Drop power supply for Host */
+ regmap_write(phy->sysctrl, SCTRL_PCIE_CMOS_OFFSET, 0x00);
+
+ kirin_pcie_clk_ctrl(phy, false);
+
+ return 0;
+}
+
+static const struct phy_ops hi3670_phy_ops = {
+ .init = hi3670_pcie_phy_init,
+ .power_on = hi3670_pcie_phy_power_on,
+ .power_off = hi3670_pcie_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int hi3670_pcie_phy_get_resources(struct hi3670_pcie_phy *phy,
+ struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ char name[32];
+ int i;
+
+ /* syscon */
+ phy->crgctrl = syscon_regmap_lookup_by_compatible("hisilicon,hi3670-crgctrl");
+ if (IS_ERR(phy->crgctrl))
+ return PTR_ERR(phy->crgctrl);
+
+ phy->sysctrl = syscon_regmap_lookup_by_compatible("hisilicon,hi3670-sctrl");
+ if (IS_ERR(phy->sysctrl))
+ return PTR_ERR(phy->sysctrl);
+
+ phy->pmctrl = syscon_regmap_lookup_by_compatible("hisilicon,hi3670-pmctrl");
+ if (IS_ERR(phy->sysctrl))
+ return PTR_ERR(phy->sysctrl);
+
+ /* clocks */
+ phy->phy_ref_clk = devm_clk_get(dev, "pcie_phy_ref");
+ if (IS_ERR(phy->phy_ref_clk))
+ return PTR_ERR(phy->phy_ref_clk);
+
+ phy->pcie_aux_clk = devm_clk_get(dev, "pcie_aux");
+ if (IS_ERR(phy->pcie_aux_clk))
+ return PTR_ERR(phy->pcie_aux_clk);
+
+ phy->apb_phy_clk = devm_clk_get(dev, "pcie_apb_phy");
+ if (IS_ERR(phy->apb_phy_clk))
+ return PTR_ERR(phy->apb_phy_clk);
+
+ phy->apb_sys_clk = devm_clk_get(dev, "pcie_apb_sys");
+ if (IS_ERR(phy->apb_sys_clk))
+ return PTR_ERR(phy->apb_sys_clk);
+
+ phy->pcie_aclk = devm_clk_get(dev, "pcie_aclk");
+ if (IS_ERR(phy->pcie_aclk))
+ return PTR_ERR(phy->pcie_aclk);
+
+ /* registers */
+ phy->base = devm_platform_ioremap_resource_byname(pdev, "phy");
+ if (IS_ERR(phy->base))
+ return PTR_ERR(phy->base);
+
+ /* perst reset gpios */
+ phy->n_gpio_resets = of_gpio_named_count(np, "reset-gpios");
+ if (phy->n_gpio_resets > MAX_GPIO_RESETS) {
+ dev_err(dev, "Too many GPIO resets!\n");
+ return -EINVAL;
+ }
+ for (i = 0; i < phy->n_gpio_resets; i++) {
+ phy->gpio_id_reset[i] = of_get_named_gpio(dev->of_node,
+ "reset-gpios", i);
+ if (phy->gpio_id_reset[i] < 0)
+ return phy->gpio_id_reset[i];
+
+ sprintf(name, "pcie_perst_%d", i);
+
+ phy->reset_names[i] = devm_kstrdup_const(dev, name,
+ GFP_KERNEL);
+ if (!phy->reset_names[i])
+ return -ENOMEM;
+ }
+
+ /* clock request gpios */
+ phy->n_gpio_clkreq = of_gpio_named_count(np, "clkreq-gpios");
+ if (phy->n_gpio_clkreq > MAX_GPIO_CLKREQ) {
+ dev_err(dev, "Too many GPIO clock requests!\n");
+ return -EINVAL;
+ }
+ for (i = 0; i < phy->n_gpio_clkreq; i++) {
+ phy->gpio_id_clkreq[i] = of_get_named_gpio(dev->of_node,
+ "clkreq-gpios", i);
+ if (phy->gpio_id_clkreq[i] < 0)
+ return phy->gpio_id_clkreq[i];
+
+ sprintf(name, "pcie_clkreq_%d", i);
+ phy->clkreq_names[i] = devm_kstrdup_const(dev, name,
+ GFP_KERNEL);
+ if (!phy->clkreq_names[i])
+ return -ENOMEM;
+ }
+
+ hi3670_pcie_get_eyeparam(phy);
+
+ return 0;
+}
+
+static int hi3670_pcie_phy_probe(struct platform_device *pdev)
+{
+ struct phy_provider *phy_provider;
+ struct device *dev = &pdev->dev;
+ struct hi3670_pcie_phy *phy;
+ struct phy *generic_phy;
+ int ret;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ phy->dev = dev;
+
+ ret = hi3670_pcie_phy_get_resources(phy, pdev);
+ if (ret)
+ return ret;
+
+ generic_phy = devm_phy_create(dev, dev->of_node, &hi3670_phy_ops);
+ if (IS_ERR(generic_phy)) {
+ dev_err(dev, "failed to create PHY\n");
+ return PTR_ERR(generic_phy);
+ }
+
+ phy_set_drvdata(generic_phy, phy);
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id hi3670_pcie_phy_match[] = {
+ {
+ .compatible = "hisilicon,hi970-pcie-phy",
+ },
+ {},
+};
+
+static struct platform_driver hi3670_pcie_phy_driver = {
+ .probe = hi3670_pcie_phy_probe,
+ .driver = {
+ .of_match_table = hi3670_pcie_phy_match,
+ .name = "hi3670_pcie_phy",
+ .suppress_bind_attrs = true,
+ }
+};
+builtin_platform_driver(hi3670_pcie_phy_driver);
--
2.31.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 6/8] phy: HiSilicon: add driver for Kirin 970 PCIe PHY
@ 2021-07-12 21:46 ` Mauro Carvalho Chehab
0 siblings, 0 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-12 21:46 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
Krzysztof Wilczyński, Manivannan Sadhasivam, Rob Herring,
Binghui Wang, Bjorn Helgaas, Greg Kroah-Hartman,
Kishon Vijay Abraham I, Lorenzo Pieralisi, Rob Herring,
Vinod Koul, Xiaowei Song, devicetree, linux-kernel, linux-pci,
linux-phy
The Kirin 970 PHY is somewhat similar to the Kirin 960, but it
does a lot more. Add the needed bits for PCIe to start working on
HiKey 970 boards.
Co-developed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
.../devicetree/bindings/pci/kirin-pcie.txt | 1 +
drivers/pci/controller/dwc/pcie-kirin.c | 1 +
drivers/phy/hisilicon/Kconfig | 10 +
drivers/phy/hisilicon/Makefile | 1 +
drivers/phy/hisilicon/phy-hi3670-pcie.c | 892 ++++++++++++++++++
5 files changed, 905 insertions(+)
create mode 100644 drivers/phy/hisilicon/phy-hi3670-pcie.c
diff --git a/Documentation/devicetree/bindings/pci/kirin-pcie.txt b/Documentation/devicetree/bindings/pci/kirin-pcie.txt
index a93a8cfa1afb..585aadfeafd1 100644
--- a/Documentation/devicetree/bindings/pci/kirin-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/kirin-pcie.txt
@@ -10,6 +10,7 @@ Additional properties are described here:
Required properties
- compatible:
"hisilicon,kirin960-pcie"
+ "hisilicon,kirin970-pcie"
- reg: Should contain rc_dbi, apb, config registers location and length.
- reg-names: Must include the following entries:
"dbi": controller configuration registers;
diff --git a/drivers/pci/controller/dwc/pcie-kirin.c b/drivers/pci/controller/dwc/pcie-kirin.c
index 026fd1e42a55..7b0f87535960 100644
--- a/drivers/pci/controller/dwc/pcie-kirin.c
+++ b/drivers/pci/controller/dwc/pcie-kirin.c
@@ -472,6 +472,7 @@ static int kirin_pcie_probe(struct platform_device *pdev)
static const struct of_device_id kirin_pcie_match[] = {
{ .compatible = "hisilicon,kirin960-pcie" },
+ { .compatible = "hisilicon,kirin970-pcie" },
{},
};
diff --git a/drivers/phy/hisilicon/Kconfig b/drivers/phy/hisilicon/Kconfig
index 30b7f1187965..65e0ff6e85ad 100644
--- a/drivers/phy/hisilicon/Kconfig
+++ b/drivers/phy/hisilicon/Kconfig
@@ -43,6 +43,16 @@ config PHY_HI3670_USB
To compile this driver as a module, choose M here.
+config PHY_HI3670_PCIE
+ tristate "hi3670 PCIe PHY support"
+ depends on (ARCH_HISI && ARM64) || COMPILE_TEST
+ select GENERIC_PHY
+ select MFD_SYSCON
+ help
+ Enable this to support the HiSilicon hi3670 PCIe PHY.
+
+ To compile this driver as a module, choose M here.
+
config PHY_HISTB_COMBPHY
tristate "HiSilicon STB SoCs COMBPHY support"
depends on (ARCH_HISI && ARM64) || COMPILE_TEST
diff --git a/drivers/phy/hisilicon/Makefile b/drivers/phy/hisilicon/Makefile
index 3c3d70dd7469..2670f2f382e1 100644
--- a/drivers/phy/hisilicon/Makefile
+++ b/drivers/phy/hisilicon/Makefile
@@ -3,6 +3,7 @@ obj-$(CONFIG_PHY_HI6220_USB) += phy-hi6220-usb.o
obj-$(CONFIG_PHY_HI3660_USB) += phy-hi3660-usb3.o
obj-$(CONFIG_PHY_HI3660_PCIE) += phy-hi3660-pcie.o
obj-$(CONFIG_PHY_HI3670_USB) += phy-hi3670-usb3.o
+obj-$(CONFIG_PHY_HI3670_PCIE) += phy-hi3670-pcie.o
obj-$(CONFIG_PHY_HISTB_COMBPHY) += phy-histb-combphy.o
obj-$(CONFIG_PHY_HISI_INNO_USB2) += phy-hisi-inno-usb2.o
obj-$(CONFIG_PHY_HIX5HD2_SATA) += phy-hix5hd2-sata.o
diff --git a/drivers/phy/hisilicon/phy-hi3670-pcie.c b/drivers/phy/hisilicon/phy-hi3670-pcie.c
new file mode 100644
index 000000000000..dcbf7d47d8e7
--- /dev/null
+++ b/drivers/phy/hisilicon/phy-hi3670-pcie.c
@@ -0,0 +1,892 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * PCIe phy driver for Kirin 970
+ *
+ * Copyright (C) 2017 HiSilicon Electronics Co., Ltd.
+ * https://www.huawei.com
+ * Copyright (C) 2021 Huawei Technologies Co., Ltd.
+ * https://www.huawei.com
+ *
+ * Authors:
+ * Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
+ * Manivannan Sadhasivam <mani@kernel.org>
+ *
+ * Based on:
+ * https://lore.kernel.org/lkml/4c9d6581478aa966698758c0420933f5defab4dd.1612335031.git.mchehab+huawei@kernel.org/
+ */
+
+#include <linux/clk.h>
+#include <linux/gpio.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define AXI_CLK_FREQ 207500000
+#define REF_CLK_FREQ 100000000
+
+/* PCIe CTRL registers */
+#define SOC_PCIECTRL_CTRL0_ADDR 0x000
+#define SOC_PCIECTRL_CTRL1_ADDR 0x004
+#define SOC_PCIECTRL_CTRL7_ADDR 0x01c
+#define SOC_PCIECTRL_CTRL12_ADDR 0x030
+#define SOC_PCIECTRL_CTRL20_ADDR 0x050
+#define SOC_PCIECTRL_CTRL21_ADDR 0x054
+#define SOC_PCIECTRL_STATE0_ADDR 0x400
+
+/* PCIe PHY registers */
+#define SOC_PCIEPHY_CTRL0_ADDR 0x000
+#define SOC_PCIEPHY_CTRL1_ADDR 0x004
+#define SOC_PCIEPHY_CTRL2_ADDR 0x008
+#define SOC_PCIEPHY_CTRL3_ADDR 0x00c
+#define SOC_PCIEPHY_CTRL38_ADDR 0x0098
+#define SOC_PCIEPHY_STATE0_ADDR 0x400
+
+#define PCIE_LINKUP_ENABLE (0x8020)
+#define PCIE_ELBI_SLV_DBI_ENABLE (0x1 << 21)
+#define PCIE_LTSSM_ENABLE_BIT (0x1 << 11)
+#define PCIEPHY_RESET_BIT (0x1 << 17)
+#define PCIEPHY_PIPE_LINE0_RESET_BIT (0x1 << 19)
+
+#define PORT_MSI_CTRL_ADDR 0x820
+#define PORT_MSI_CTRL_UPPER_ADDR 0x824
+#define PORT_MSI_CTRL_INT0_ENABLE 0x828
+
+#define EYEPARAM_NOCFG 0xFFFFFFFF
+#define RAWLANEN_DIG_PCS_XF_TX_OVRD_IN_1 0x3001
+#define SUP_DIG_LVL_OVRD_IN 0xf
+#define LANEN_DIG_ASIC_TX_OVRD_IN_1 0x1002
+#define LANEN_DIG_ASIC_TX_OVRD_IN_2 0x1003
+
+/* hi3670 pciephy register */
+#define SOC_PCIEPHY_MMC1PLL_CTRL1 0xc04
+#define SOC_PCIEPHY_MMC1PLL_CTRL16 0xC40
+#define SOC_PCIEPHY_MMC1PLL_CTRL17 0xC44
+#define SOC_PCIEPHY_MMC1PLL_CTRL20 0xC50
+#define SOC_PCIEPHY_MMC1PLL_CTRL21 0xC54
+#define SOC_PCIEPHY_MMC1PLL_STAT0 0xE00
+
+#define CRGPERIPH_PEREN12 0x470
+#define CRGPERIPH_PERDIS12 0x474
+#define CRGPERIPH_PCIECTRL0 0x800
+
+/* define ie,oe cfg */
+#define IO_IE_EN_HARD_BYPASS (0x1 << 27)
+#define IO_OE_EN_HARD_BYPASS (0x1 << 11)
+#define IO_HARD_CTRL_DEBOUNCE_BYPASS (0x1 << 10)
+#define IO_OE_GT_MODE (0x2 << 7)
+#define DEBOUNCE_WAITCFG_IN (0xf << 20)
+#define DEBOUNCE_WAITCFG_OUT (0xf << 13)
+
+/* noc power domain */
+#define NOC_POWER_IDLEREQ_1 0x38c
+#define NOC_POWER_IDLE_1 0x394
+#define NOC_PW_MASK 0x10000
+#define NOC_PW_SET_BIT 0x1
+
+/* Number of GPIOs required by PHY */
+#define MAX_GPIO_RESETS 4
+#define MAX_GPIO_CLKREQ 3
+#define NUM_EYEPARAM 5
+
+/* info located in sysctrl */
+#define SCTRL_PCIE_CMOS_OFFSET 0x60
+#define SCTRL_PCIE_CMOS_BIT 0x10
+#define SCTRL_PCIE_ISO_OFFSET 0x44
+#define SCTRL_PCIE_ISO_BIT 0x30
+#define SCTRL_PCIE_HPCLK_OFFSET 0x190
+#define SCTRL_PCIE_HPCLK_BIT 0x184000
+#define SCTRL_PCIE_OE_OFFSET 0x14a
+#define PCIE_DEBOUNCE_PARAM 0xF0F400
+#define PCIE_OE_BYPASS (0x3 << 28)
+
+/* peri_crg ctrl */
+#define CRGCTRL_PCIE_ASSERT_OFFSET 0x88
+#define CRGCTRL_PCIE_ASSERT_BIT 0x8c000000
+
+/* Time for delay */
+#define REF_2_PERST_MIN 20000
+#define REF_2_PERST_MAX 25000
+#define PERST_2_ACCESS_MIN 10000
+#define PERST_2_ACCESS_MAX 12000
+#define PIPE_CLK_WAIT_MIN 550
+#define PIPE_CLK_WAIT_MAX 600
+#define TIME_CMOS_MIN 100
+#define TIME_CMOS_MAX 105
+#define TIME_PHY_PD_MIN 10
+#define TIME_PHY_PD_MAX 11
+
+struct hi3670_pcie_phy {
+ struct device *dev;
+ void __iomem *base;
+ struct regmap *apb;
+ struct regmap *crgctrl;
+ struct regmap *sysctrl;
+ struct regmap *pmctrl;
+ struct clk *apb_sys_clk;
+ struct clk *apb_phy_clk;
+ struct clk *phy_ref_clk;
+ struct clk *pcie_aclk;
+ struct clk *pcie_aux_clk;
+ int n_gpio_resets;
+ int n_gpio_clkreq;
+ int gpio_id_reset[MAX_GPIO_RESETS];
+ const char *reset_names[MAX_GPIO_RESETS];
+ int gpio_id_clkreq[MAX_GPIO_CLKREQ];
+ const char *clkreq_names[MAX_GPIO_CLKREQ];
+ u32 eye_param[NUM_EYEPARAM];
+};
+
+
+/* Registers in PCIePHY */
+static inline void hi3670_apb_phy_writel(struct hi3670_pcie_phy *phy,
+ u32 val, u32 reg)
+{
+ writel(val, phy->base + 0x40000 + reg);
+}
+
+static inline u32 hi3670_apb_phy_readl(struct hi3670_pcie_phy *phy, u32 reg)
+{
+ return readl(phy->base + 0x40000 + reg);
+}
+
+static inline void kirin_apb_natural_phy_writel(struct hi3670_pcie_phy *phy,
+ u32 val, u32 reg)
+{
+ writel(val, phy->base + reg * 4);
+}
+
+static inline u32 kirin_apb_natural_phy_readl(struct hi3670_pcie_phy *phy,
+ u32 reg)
+{
+ return readl(phy->base + reg * 4);
+}
+
+static void hi3670_pcie_phy_oe_enable(struct hi3670_pcie_phy *phy)
+{
+ u32 val;
+
+ regmap_read(phy->sysctrl, SCTRL_PCIE_OE_OFFSET, &val);
+ val |= PCIE_DEBOUNCE_PARAM;
+ val &= ~PCIE_OE_BYPASS;
+ regmap_write(phy->sysctrl, SCTRL_PCIE_OE_OFFSET, val);
+}
+
+void hi3670_pcie_get_eyeparam(struct hi3670_pcie_phy *phy)
+{
+ struct device *dev = phy->dev;
+ struct device_node *np;
+ int ret, i;
+
+ np = dev->of_node;
+
+ ret = of_property_read_u32_array(np, "hisilicon,eye-diagram-param",
+ phy->eye_param, NUM_EYEPARAM);
+ if (!ret)
+ return;
+
+ /* There's no optional eye_param property. Set array to default */
+ for (i = 0; i < NUM_EYEPARAM; i++)
+ phy->eye_param[i] = EYEPARAM_NOCFG;
+}
+
+static void hi3670_pcie_set_eyeparam(struct hi3670_pcie_phy *phy)
+{
+ u32 val;
+
+ val = kirin_apb_natural_phy_readl(phy, RAWLANEN_DIG_PCS_XF_TX_OVRD_IN_1);
+
+ if (phy->eye_param[1] != EYEPARAM_NOCFG) {
+ val &= (~0xf00);
+ val |= (phy->eye_param[1] << 8) | (0x1 << 12);
+ }
+ kirin_apb_natural_phy_writel(phy, val, RAWLANEN_DIG_PCS_XF_TX_OVRD_IN_1);
+
+ val = kirin_apb_natural_phy_readl(phy, LANEN_DIG_ASIC_TX_OVRD_IN_2);
+ val &= (~0x1FBF);
+ if (phy->eye_param[2] != EYEPARAM_NOCFG)
+ val |= (phy->eye_param[2]<< 0) | (0x1 << 6);
+
+ if (phy->eye_param[3] != EYEPARAM_NOCFG)
+ val |= (phy->eye_param[3] << 7) | (0x1 << 13);
+
+ kirin_apb_natural_phy_writel(phy, val, LANEN_DIG_ASIC_TX_OVRD_IN_2);
+
+ val = kirin_apb_natural_phy_readl(phy, SUP_DIG_LVL_OVRD_IN);
+ if (phy->eye_param[0] != EYEPARAM_NOCFG) {
+ val &= (~0x1C0);
+ val |= (phy->eye_param[0] << 6) | (0x1 << 9);
+ }
+ kirin_apb_natural_phy_writel(phy, val, SUP_DIG_LVL_OVRD_IN);
+
+ val = kirin_apb_natural_phy_readl(phy, LANEN_DIG_ASIC_TX_OVRD_IN_1);
+ if (phy->eye_param[4] != EYEPARAM_NOCFG) {
+ val &= (~0x7E00);
+ val |= (phy->eye_param[4] << 9) | (0x1 << 15);
+ }
+ kirin_apb_natural_phy_writel(phy, val, LANEN_DIG_ASIC_TX_OVRD_IN_1);
+}
+
+static int hi3670_pcie_gpio_request(struct hi3670_pcie_phy *phy,
+ struct device *dev)
+{
+ int ret, i;
+
+ for (i = 0; i < phy->n_gpio_resets; i++) {
+ if (!gpio_is_valid(phy->gpio_id_reset[i])) {
+ dev_err(dev, "unable to get a valid %s gpio\n",
+ phy->reset_names[i]);
+ return -ENODEV;
+ }
+
+ ret = devm_gpio_request(dev, phy->gpio_id_reset[i],
+ phy->reset_names[i]);
+ if (ret)
+ return ret;
+ }
+
+ for (i = 0; i < phy->n_gpio_clkreq; i++) {
+ if (!gpio_is_valid(phy->gpio_id_clkreq[i])) {
+ dev_err(dev, "unable to get a valid %s gpio\n",
+ phy->clkreq_names[i]);
+ return -ENODEV;
+ }
+
+ ret = devm_gpio_request(dev, phy->gpio_id_clkreq[i],
+ phy->clkreq_names[i]);
+ if (ret)
+ return ret;
+ }
+
+ return ret;
+}
+
+static void hi3670_pcie_natural_cfg(struct hi3670_pcie_phy *phy)
+{
+ u32 val;
+
+ /* change 2p mem_ctrl */
+ regmap_write(phy->apb, SOC_PCIECTRL_CTRL20_ADDR, 0x02605550);
+
+ /* pull up sys_aux_pwr_det */
+ regmap_read(phy->apb, SOC_PCIECTRL_CTRL7_ADDR, &val);
+ val |= (0x1 << 10);
+ regmap_write(phy->apb, SOC_PCIECTRL_CTRL7_ADDR, val);
+
+ /* output, pull down */
+ regmap_read(phy->apb, SOC_PCIECTRL_CTRL12_ADDR, &val);
+ val &= ~(0x3 << 2);
+ val |= (0x1 << 1);
+ val &= ~(0x1 << 0);
+ regmap_write(phy->apb, SOC_PCIECTRL_CTRL12_ADDR, val);
+
+ /* Handle phy_reset and lane0_reset to HW */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_CTRL1_ADDR);
+ val |= PCIEPHY_RESET_BIT;
+ val &= ~PCIEPHY_PIPE_LINE0_RESET_BIT;
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_CTRL1_ADDR);
+
+ /* fix chip bug: TxDetectRx fail */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_CTRL38_ADDR);
+ val |= (0x1 << 2);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_CTRL38_ADDR);
+}
+
+static void hi3670_pcie_pll_init(struct hi3670_pcie_phy *phy)
+{
+ u32 val;
+
+ /* choose FNPLL */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL1);
+ val |= (0x1 << 27);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL1);
+
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL16);
+ val &= 0xF000FFFF;
+ /* fnpll fbdiv = 0xD0 */
+ val |= (0xd0 << 16);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL16);
+
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL17);
+ val &= 0xFF000000;
+ /* fnpll fracdiv = 0x555555 */
+ val |= (0x555555 << 0);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL17);
+
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL20);
+ val &= 0xF5FF88FF;
+ /* fnpll dll_en = 0x1 */
+ val |= (0x1 << 27);
+ /* fnpll postdiv1 = 0x5 */
+ val |= (0x5 << 8);
+ /* fnpll postdiv2 = 0x4 */
+ val |= (0x4 << 12);
+ /* fnpll pll_mode = 0x0 */
+ val &= ~(0x1 << 25);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL20);
+
+ hi3670_apb_phy_writel(phy, 0x20, SOC_PCIEPHY_MMC1PLL_CTRL21);
+}
+
+static int hi3670_pcie_pll_ctrl(struct hi3670_pcie_phy *phy, bool enable)
+{
+ struct device *dev = phy->dev;
+ u32 val;
+ int time = 200;
+
+ if (enable) {
+ /* pd = 0 */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL16);
+ val &= ~(0x1 << 0);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL16);
+
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_STAT0);
+
+ /* choose FNPLL */
+ while (!(val & 0x10)) {
+ if (!time) {
+ dev_err(dev, "wait for pll_lock timeout\n");
+ return -1;
+ }
+ time --;
+ udelay(1);
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_STAT0);
+ }
+
+ /* pciepll_bp = 0 */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL20);
+ val &= ~(0x1 << 16);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL20);
+
+ } else {
+ /* pd = 1 */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL16);
+ val |= (0x1 << 0);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL16);
+
+ /* pciepll_bp = 1 */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL20);
+ val |= (0x1 << 16);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL20);
+ }
+
+ return 0;
+}
+
+static void hi3670_pcie_hp_debounce_gt(struct hi3670_pcie_phy *phy, bool open)
+{
+ if (open)
+ /* gt_clk_pcie_hp/gt_clk_pcie_debounce open */
+ regmap_write(phy->crgctrl, CRGPERIPH_PEREN12, 0x9000);
+ else
+ /* gt_clk_pcie_hp/gt_clk_pcie_debounce close */
+ regmap_write(phy->crgctrl, CRGPERIPH_PERDIS12, 0x9000);
+}
+
+static void hi3670_pcie_phyref_gt(struct hi3670_pcie_phy *phy, bool open)
+{
+ unsigned int val;
+
+ regmap_read(phy->crgctrl, CRGPERIPH_PCIECTRL0, &val);
+
+ if (open)
+ val &= ~(0x1 << 1); //enable hard gt mode
+ else
+ val |= (0x1 << 1); //disable hard gt mode
+
+ regmap_write(phy->crgctrl, CRGPERIPH_PCIECTRL0, val);
+
+ /* disable soft gt mode */
+ regmap_write(phy->crgctrl, CRGPERIPH_PERDIS12, 0x4000);
+}
+
+static void hi3670_pcie_oe_ctrl(struct hi3670_pcie_phy *phy, bool en_flag)
+{
+ unsigned int val;
+
+ regmap_read(phy->crgctrl , CRGPERIPH_PCIECTRL0, &val);
+
+ /* set ie cfg */
+ val |= IO_IE_EN_HARD_BYPASS;
+
+ /* set oe cfg */
+ val &= ~IO_HARD_CTRL_DEBOUNCE_BYPASS;
+
+ /* set phy_debounce in&out time */
+ val |= (DEBOUNCE_WAITCFG_IN | DEBOUNCE_WAITCFG_OUT);
+
+ /* select oe_gt_mode */
+ val |= IO_OE_GT_MODE;
+
+ if (en_flag)
+ val &= ~IO_OE_EN_HARD_BYPASS;
+ else
+ val |= IO_OE_EN_HARD_BYPASS;
+
+ regmap_write(phy->crgctrl, CRGPERIPH_PCIECTRL0, val);
+}
+
+static void hi3670_pcie_ioref_gt(struct hi3670_pcie_phy *phy, bool open)
+{
+ unsigned int val;
+
+ if (open) {
+ regmap_write(phy->apb, SOC_PCIECTRL_CTRL21_ADDR, 0x20000070);
+
+ hi3670_pcie_oe_ctrl(phy, true);
+
+ /* en hard gt mode */
+ regmap_read(phy->crgctrl, CRGPERIPH_PCIECTRL0, &val);
+ val &= ~(0x1 << 0);
+ regmap_write(phy->crgctrl, CRGPERIPH_PCIECTRL0, val);
+
+ /* disable soft gt mode */
+ regmap_write(phy->crgctrl, CRGPERIPH_PERDIS12, 0x2000);
+
+ } else {
+ /* disable hard gt mode */
+ regmap_read(phy->crgctrl, CRGPERIPH_PCIECTRL0, &val);
+ val |= (0x1 << 0);
+ regmap_write(phy->crgctrl, CRGPERIPH_PCIECTRL0, val);
+
+ /* disable soft gt mode */
+ regmap_write(phy->crgctrl, CRGPERIPH_PERDIS12, 0x2000);
+
+ hi3670_pcie_oe_ctrl(phy, false);
+ }
+}
+
+static int hi3670_pcie_allclk_ctrl(struct hi3670_pcie_phy *phy, bool clk_on)
+{
+ struct device *dev = phy->dev;
+ u32 val;
+ int ret = 0;
+
+ if (!clk_on)
+ goto close_clocks;
+
+ /* choose 100MHz clk src: Bit[8]==1 pad, Bit[8]==0 pll */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_CTRL1_ADDR);
+ val &= ~(0x1 << 8);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_CTRL1_ADDR);
+
+ hi3670_pcie_pll_init(phy);
+
+ ret = hi3670_pcie_pll_ctrl(phy, true);
+ if (ret) {
+ dev_err(dev, "Failed to enable pll\n");
+ return -1;
+ }
+ hi3670_pcie_hp_debounce_gt(phy, true);
+ hi3670_pcie_phyref_gt(phy, true);
+ hi3670_pcie_ioref_gt(phy, true);
+
+ ret = clk_set_rate(phy->pcie_aclk, AXI_CLK_FREQ);
+ if (ret) {
+ dev_err(dev, "Failed to set rate\n");
+ goto close_clocks;
+ }
+
+ return 0;
+
+close_clocks:
+ hi3670_pcie_ioref_gt(phy, false);
+ hi3670_pcie_phyref_gt(phy, false);
+ hi3670_pcie_hp_debounce_gt(phy, false);
+
+ hi3670_pcie_pll_ctrl(phy, false);
+
+ return ret;
+}
+
+static bool is_pipe_clk_stable(struct hi3670_pcie_phy *phy)
+{
+ struct device *dev = phy->dev;
+ u32 val;
+ u32 time = 100;
+ u32 pipe_clk_stable = 0x1 << 19;
+
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_STATE0_ADDR);
+ while (val & pipe_clk_stable) {
+ mdelay(1);
+ if (time == 0) {
+ dev_err(dev, "PIPE clk is not stable\n");
+ return false;
+ }
+ time--;
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_STATE0_ADDR);
+ }
+
+ return true;
+}
+
+static int hi3670_pcie_noc_power(struct hi3670_pcie_phy *phy, bool enable)
+{
+ struct device *dev = phy->dev;
+ u32 time = 100;
+ unsigned int val = NOC_PW_MASK;
+ int rst;
+
+ if (enable)
+ val = NOC_PW_MASK | NOC_PW_SET_BIT;
+ else
+ val = NOC_PW_MASK;
+ rst = enable ? 1 : 0;
+
+ regmap_write(phy->pmctrl, NOC_POWER_IDLEREQ_1, val);
+
+ time = 100;
+ regmap_read(phy->pmctrl, NOC_POWER_IDLE_1, &val);
+ while((val & NOC_PW_SET_BIT) != rst) {
+ udelay(10);
+ if (!time) {
+ dev_err(dev, "Failed to reverse noc power-status\n");
+ return -1;
+ }
+ time--;
+ regmap_read(phy->pmctrl, NOC_POWER_IDLE_1, &val);
+ }
+
+ return 0;
+}
+
+static int hi3670_pcie_get_apb(struct hi3670_pcie_phy *phy)
+{
+ struct device_node *pcie_port;
+ struct device *dev = phy->dev;
+ struct device *pcie_dev;
+
+ pcie_port = of_get_child_by_name(dev->parent->of_node, "pcie");
+ if (!pcie_port) {
+ dev_err(dev, "no pcie node found in %s\n",
+ dev->parent->of_node->full_name);
+ return -ENODEV;
+ }
+
+ pcie_dev = bus_find_device_by_of_node(&platform_bus_type, pcie_port);
+ if (!pcie_dev) {
+ dev_err(dev, "Didn't find pcie device\n");
+ return -ENODEV;
+ }
+
+ /*
+ * We might just use NULL instead of the APB name, as the
+ * pcie-kirin currently registers directly just one regmap (although
+ * the DWC driver register other regmaps).
+ *
+ * Yet, it sounds safer to warrant that it will be accessing the
+ * right regmap. So, let's use the named version.
+ */
+ phy->apb = dev_get_regmap(pcie_dev, "kirin_pcie_apb");
+ if (!phy->apb) {
+ dev_err(dev, "Failed to get APB regmap\n");
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+
+static int kirin_pcie_clk_ctrl(struct hi3670_pcie_phy *phy, bool enable)
+{
+ int ret = 0;
+
+ if (!enable)
+ goto close_clk;
+
+ ret = clk_set_rate(phy->phy_ref_clk, REF_CLK_FREQ);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(phy->phy_ref_clk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(phy->apb_sys_clk);
+ if (ret)
+ goto apb_sys_fail;
+
+ ret = clk_prepare_enable(phy->apb_phy_clk);
+ if (ret)
+ goto apb_phy_fail;
+
+ ret = clk_prepare_enable(phy->pcie_aclk);
+ if (ret)
+ goto aclk_fail;
+
+ ret = clk_prepare_enable(phy->pcie_aux_clk);
+ if (ret)
+ goto aux_clk_fail;
+
+ return 0;
+
+close_clk:
+ clk_disable_unprepare(phy->pcie_aux_clk);
+aux_clk_fail:
+ clk_disable_unprepare(phy->pcie_aclk);
+aclk_fail:
+ clk_disable_unprepare(phy->apb_phy_clk);
+apb_phy_fail:
+ clk_disable_unprepare(phy->apb_sys_clk);
+apb_sys_fail:
+ clk_disable_unprepare(phy->phy_ref_clk);
+
+ return ret;
+}
+
+static int hi3670_pcie_phy_init(struct phy *generic_phy)
+{
+ struct hi3670_pcie_phy *phy = phy_get_drvdata(generic_phy);
+ struct device *dev = phy->dev;
+ int ret;
+
+ /*
+ * The code under hi3670_pcie_get_apb() need to access the
+ * DWC APB registers. So, get them from
+ * the pcie driver's regmap (see pcie-kirin regmap).
+ *
+ * Such kind of resource can only be obtained during the PCIe
+ * power_on sequence, as the code inside pcie-kirin needs to
+ * be already probed, as it needs to register the APB regmap.
+ */
+
+ ret = hi3670_pcie_get_apb(phy);
+ if (ret)
+ return ret;
+
+ /* phy regulator needs to be powered on before calling it */
+ return hi3670_pcie_gpio_request(phy, dev);
+}
+
+static int hi3670_pcie_phy_power_on(struct phy *generic_phy)
+{
+ struct hi3670_pcie_phy *phy = phy_get_drvdata(generic_phy);
+ int val, ret, i;
+
+ /* Power supply for Host */
+ regmap_write(phy->sysctrl,
+ SCTRL_PCIE_CMOS_OFFSET, SCTRL_PCIE_CMOS_BIT);
+ usleep_range(TIME_CMOS_MIN, TIME_CMOS_MAX);
+
+ hi3670_pcie_phy_oe_enable(phy);
+
+ for (i = 0; i < phy->n_gpio_clkreq; i++) {
+ ret = gpio_direction_output(phy->gpio_id_clkreq[i], 0);
+ if (ret)
+ return ret;
+ }
+
+ ret = kirin_pcie_clk_ctrl(phy, true);
+ if (ret)
+ return ret;
+
+ /* ISO disable, PCIeCtrl, PHY assert and clk gate clear */
+ regmap_write(phy->sysctrl,
+ SCTRL_PCIE_ISO_OFFSET, SCTRL_PCIE_ISO_BIT);
+ regmap_write(phy->crgctrl,
+ CRGCTRL_PCIE_ASSERT_OFFSET, CRGCTRL_PCIE_ASSERT_BIT);
+ regmap_write(phy->sysctrl,
+ SCTRL_PCIE_HPCLK_OFFSET, SCTRL_PCIE_HPCLK_BIT);
+
+ hi3670_pcie_natural_cfg(phy);
+
+ ret = hi3670_pcie_allclk_ctrl(phy, true);
+ if (ret)
+ goto disable_clks;
+
+ /* pull down phy_test_powerdown signal */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_CTRL0_ADDR);
+ val &= ~(0x1 << 22);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_CTRL0_ADDR);
+
+ /* deassert controller perst_n */
+ regmap_read(phy->apb, SOC_PCIECTRL_CTRL12_ADDR, &val);
+ val |= (0x1 << 2);
+ regmap_write(phy->apb, SOC_PCIECTRL_CTRL12_ADDR, val);
+ udelay(10);
+
+ /* perst assert Endpoints */
+ usleep_range(21000, 23000);
+ for (i = 0; i < phy->n_gpio_resets; i++) {
+ ret = gpio_direction_output(phy->gpio_id_reset[i], 1);
+ if (ret)
+ return ret;
+ }
+ usleep_range(10000, 11000);
+
+ ret = is_pipe_clk_stable(phy);
+ if (!ret)
+ goto disable_clks;
+
+ hi3670_pcie_set_eyeparam(phy);
+
+ ret = hi3670_pcie_noc_power(phy, false);
+ if (ret)
+ goto disable_clks;
+
+ return 0;
+
+disable_clks:
+ kirin_pcie_clk_ctrl(phy, false);
+ return ret;
+}
+
+static int hi3670_pcie_phy_power_off(struct phy *generic_phy)
+{
+ struct hi3670_pcie_phy *phy = phy_get_drvdata(generic_phy);
+
+ /* Drop power supply for Host */
+ regmap_write(phy->sysctrl, SCTRL_PCIE_CMOS_OFFSET, 0x00);
+
+ kirin_pcie_clk_ctrl(phy, false);
+
+ return 0;
+}
+
+static const struct phy_ops hi3670_phy_ops = {
+ .init = hi3670_pcie_phy_init,
+ .power_on = hi3670_pcie_phy_power_on,
+ .power_off = hi3670_pcie_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int hi3670_pcie_phy_get_resources(struct hi3670_pcie_phy *phy,
+ struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ char name[32];
+ int i;
+
+ /* syscon */
+ phy->crgctrl = syscon_regmap_lookup_by_compatible("hisilicon,hi3670-crgctrl");
+ if (IS_ERR(phy->crgctrl))
+ return PTR_ERR(phy->crgctrl);
+
+ phy->sysctrl = syscon_regmap_lookup_by_compatible("hisilicon,hi3670-sctrl");
+ if (IS_ERR(phy->sysctrl))
+ return PTR_ERR(phy->sysctrl);
+
+ phy->pmctrl = syscon_regmap_lookup_by_compatible("hisilicon,hi3670-pmctrl");
+ if (IS_ERR(phy->sysctrl))
+ return PTR_ERR(phy->sysctrl);
+
+ /* clocks */
+ phy->phy_ref_clk = devm_clk_get(dev, "pcie_phy_ref");
+ if (IS_ERR(phy->phy_ref_clk))
+ return PTR_ERR(phy->phy_ref_clk);
+
+ phy->pcie_aux_clk = devm_clk_get(dev, "pcie_aux");
+ if (IS_ERR(phy->pcie_aux_clk))
+ return PTR_ERR(phy->pcie_aux_clk);
+
+ phy->apb_phy_clk = devm_clk_get(dev, "pcie_apb_phy");
+ if (IS_ERR(phy->apb_phy_clk))
+ return PTR_ERR(phy->apb_phy_clk);
+
+ phy->apb_sys_clk = devm_clk_get(dev, "pcie_apb_sys");
+ if (IS_ERR(phy->apb_sys_clk))
+ return PTR_ERR(phy->apb_sys_clk);
+
+ phy->pcie_aclk = devm_clk_get(dev, "pcie_aclk");
+ if (IS_ERR(phy->pcie_aclk))
+ return PTR_ERR(phy->pcie_aclk);
+
+ /* registers */
+ phy->base = devm_platform_ioremap_resource_byname(pdev, "phy");
+ if (IS_ERR(phy->base))
+ return PTR_ERR(phy->base);
+
+ /* perst reset gpios */
+ phy->n_gpio_resets = of_gpio_named_count(np, "reset-gpios");
+ if (phy->n_gpio_resets > MAX_GPIO_RESETS) {
+ dev_err(dev, "Too many GPIO resets!\n");
+ return -EINVAL;
+ }
+ for (i = 0; i < phy->n_gpio_resets; i++) {
+ phy->gpio_id_reset[i] = of_get_named_gpio(dev->of_node,
+ "reset-gpios", i);
+ if (phy->gpio_id_reset[i] < 0)
+ return phy->gpio_id_reset[i];
+
+ sprintf(name, "pcie_perst_%d", i);
+
+ phy->reset_names[i] = devm_kstrdup_const(dev, name,
+ GFP_KERNEL);
+ if (!phy->reset_names[i])
+ return -ENOMEM;
+ }
+
+ /* clock request gpios */
+ phy->n_gpio_clkreq = of_gpio_named_count(np, "clkreq-gpios");
+ if (phy->n_gpio_clkreq > MAX_GPIO_CLKREQ) {
+ dev_err(dev, "Too many GPIO clock requests!\n");
+ return -EINVAL;
+ }
+ for (i = 0; i < phy->n_gpio_clkreq; i++) {
+ phy->gpio_id_clkreq[i] = of_get_named_gpio(dev->of_node,
+ "clkreq-gpios", i);
+ if (phy->gpio_id_clkreq[i] < 0)
+ return phy->gpio_id_clkreq[i];
+
+ sprintf(name, "pcie_clkreq_%d", i);
+ phy->clkreq_names[i] = devm_kstrdup_const(dev, name,
+ GFP_KERNEL);
+ if (!phy->clkreq_names[i])
+ return -ENOMEM;
+ }
+
+ hi3670_pcie_get_eyeparam(phy);
+
+ return 0;
+}
+
+static int hi3670_pcie_phy_probe(struct platform_device *pdev)
+{
+ struct phy_provider *phy_provider;
+ struct device *dev = &pdev->dev;
+ struct hi3670_pcie_phy *phy;
+ struct phy *generic_phy;
+ int ret;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ phy->dev = dev;
+
+ ret = hi3670_pcie_phy_get_resources(phy, pdev);
+ if (ret)
+ return ret;
+
+ generic_phy = devm_phy_create(dev, dev->of_node, &hi3670_phy_ops);
+ if (IS_ERR(generic_phy)) {
+ dev_err(dev, "failed to create PHY\n");
+ return PTR_ERR(generic_phy);
+ }
+
+ phy_set_drvdata(generic_phy, phy);
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id hi3670_pcie_phy_match[] = {
+ {
+ .compatible = "hisilicon,hi970-pcie-phy",
+ },
+ {},
+};
+
+static struct platform_driver hi3670_pcie_phy_driver = {
+ .probe = hi3670_pcie_phy_probe,
+ .driver = {
+ .of_match_table = hi3670_pcie_phy_match,
+ .name = "hi3670_pcie_phy",
+ .suppress_bind_attrs = true,
+ }
+};
+builtin_platform_driver(hi3670_pcie_phy_driver);
--
2.31.1
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 7/8] PCI: kirin: Drop the PHY logic from the driver
2021-07-12 21:46 ` Mauro Carvalho Chehab
@ 2021-07-12 21:46 ` Mauro Carvalho Chehab
-1 siblings, 0 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-12 21:46 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
Krzysztof Wilczyński, Manivannan Sadhasivam, Rob Herring,
Binghui Wang, Bjorn Helgaas, Lorenzo Pieralisi, Rob Herring,
Wei Xu, Xiaowei Song, devicetree, linux-arm-kernel, linux-kernel,
linux-pci
The pcie-kirin PCIe driver contains internally a PHY interface for
a Kirin 960. Drop it and add support for using the new PHY driver
for Kirin 960, updating DT accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 29 ++-
drivers/pci/controller/dwc/pcie-kirin.c | 252 +++-------------------
2 files changed, 47 insertions(+), 234 deletions(-)
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
index f1ec87c05842..772bb632814f 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
@@ -995,17 +995,33 @@ spi3: spi@ff3b3000 {
status = "disabled";
};
+ pcie_phy: pcie-phy@f3f2000 {
+ compatible = "hisilicon,hi960-pcie-phy";
+ reg = <0x0 0xf3f20000 0x0 0x40000>;
+ reg-names = "phy";
+ clocks = <&crg_ctrl HI3660_PCIEPHY_REF>,
+ <&crg_ctrl HI3660_CLK_GATE_PCIEAUX>,
+ <&crg_ctrl HI3660_PCLK_GATE_PCIE_PHY>,
+ <&crg_ctrl HI3660_PCLK_GATE_PCIE_SYS>,
+ <&crg_ctrl HI3660_ACLK_GATE_PCIE>;
+ clock-names = "pcie_phy_ref", "pcie_aux",
+ "pcie_apb_phy", "pcie_apb_sys",
+ "pcie_aclk";
+ reset-gpios = <&gpio11 1 0 >;
+ #phy-cells = <0>;
+ };
+
pcie@f4000000 {
compatible = "hisilicon,kirin960-pcie";
reg = <0x0 0xf4000000 0x0 0x1000>,
<0x0 0xff3fe000 0x0 0x1000>,
- <0x0 0xf3f20000 0x0 0x40000>,
<0x0 0xf5000000 0x0 0x2000>;
- reg-names = "dbi", "apb", "phy", "config";
+ reg-names = "dbi", "apb", "config";
bus-range = <0x0 0x1>;
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
+ phys = <&pcie_phy>;
ranges = <0x02000000 0x0 0x00000000
0x0 0xf6000000
0x0 0x02000000>;
@@ -1022,15 +1038,6 @@ &gic GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
&gic GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
<0x0 0 0 4
&gic GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&crg_ctrl HI3660_PCIEPHY_REF>,
- <&crg_ctrl HI3660_CLK_GATE_PCIEAUX>,
- <&crg_ctrl HI3660_PCLK_GATE_PCIE_PHY>,
- <&crg_ctrl HI3660_PCLK_GATE_PCIE_SYS>,
- <&crg_ctrl HI3660_ACLK_GATE_PCIE>;
- clock-names = "pcie_phy_ref", "pcie_aux",
- "pcie_apb_phy", "pcie_apb_sys",
- "pcie_aclk";
- reset-gpios = <&gpio11 1 0 >;
};
/* UFS */
diff --git a/drivers/pci/controller/dwc/pcie-kirin.c b/drivers/pci/controller/dwc/pcie-kirin.c
index 7b0f87535960..66662f7b0fc9 100644
--- a/drivers/pci/controller/dwc/pcie-kirin.c
+++ b/drivers/pci/controller/dwc/pcie-kirin.c
@@ -9,7 +9,6 @@
*/
#include <linux/compiler.h>
-#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/gpio.h>
@@ -21,6 +20,7 @@
#include <linux/pci.h>
#include <linux/pci_regs.h>
#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
#include <linux/regmap.h>
#include <linux/resource.h>
#include <linux/types.h>
@@ -28,26 +28,17 @@
#define to_kirin_pcie(x) dev_get_drvdata((x)->dev)
-#define REF_CLK_FREQ 100000000
-
/* PCIe ELBI registers */
#define SOC_PCIECTRL_CTRL0_ADDR 0x000
#define SOC_PCIECTRL_CTRL1_ADDR 0x004
-#define SOC_PCIEPHY_CTRL2_ADDR 0x008
-#define SOC_PCIEPHY_CTRL3_ADDR 0x00c
#define PCIE_ELBI_SLV_DBI_ENABLE (0x1 << 21)
/* info located in APB */
#define PCIE_APP_LTSSM_ENABLE 0x01c
-#define PCIE_APB_PHY_CTRL0 0x0
-#define PCIE_APB_PHY_CTRL1 0x4
#define PCIE_APB_PHY_STATUS0 0x400
#define PCIE_LINKUP_ENABLE (0x8020)
#define PCIE_LTSSM_ENABLE_BIT (0x1 << 11)
#define PIPE_CLK_STABLE (0x1 << 19)
-#define PHY_REF_PAD_BIT (0x1 << 8)
-#define PHY_PWR_DOWN_BIT (0x1 << 22)
-#define PHY_RST_ACK_BIT (0x1 << 16)
/* info located in sysctrl */
#define SCTRL_PCIE_CMOS_OFFSET 0x60
@@ -60,36 +51,10 @@
#define PCIE_DEBOUNCE_PARAM 0xF0F400
#define PCIE_OE_BYPASS (0x3 << 28)
-/* peri_crg ctrl */
-#define CRGCTRL_PCIE_ASSERT_OFFSET 0x88
-#define CRGCTRL_PCIE_ASSERT_BIT 0x8c000000
-
-/* Time for delay */
-#define REF_2_PERST_MIN 20000
-#define REF_2_PERST_MAX 25000
-#define PERST_2_ACCESS_MIN 10000
-#define PERST_2_ACCESS_MAX 12000
-#define LINK_WAIT_MIN 900
-#define LINK_WAIT_MAX 1000
-#define PIPE_CLK_WAIT_MIN 550
-#define PIPE_CLK_WAIT_MAX 600
-#define TIME_CMOS_MIN 100
-#define TIME_CMOS_MAX 105
-#define TIME_PHY_PD_MIN 10
-#define TIME_PHY_PD_MAX 11
-
struct kirin_pcie {
struct dw_pcie *pci;
+ struct phy *phy;
void __iomem *apb_base;
- void __iomem *phy_base;
- struct regmap *crgctrl;
- struct regmap *sysctrl;
- struct clk *apb_sys_clk;
- struct clk *apb_phy_clk;
- struct clk *phy_ref_clk;
- struct clk *pcie_aclk;
- struct clk *pcie_aux_clk;
- int gpio_id_reset;
};
/* Registers in PCIeCTRL */
@@ -104,46 +69,6 @@ static inline u32 kirin_apb_ctrl_readl(struct kirin_pcie *kirin_pcie, u32 reg)
return readl(kirin_pcie->apb_base + reg);
}
-/* Registers in PCIePHY */
-static inline void kirin_apb_phy_writel(struct kirin_pcie *kirin_pcie,
- u32 val, u32 reg)
-{
- writel(val, kirin_pcie->phy_base + reg);
-}
-
-static inline u32 kirin_apb_phy_readl(struct kirin_pcie *kirin_pcie, u32 reg)
-{
- return readl(kirin_pcie->phy_base + reg);
-}
-
-static long kirin_pcie_get_clk(struct kirin_pcie *kirin_pcie,
- struct platform_device *pdev)
-{
- struct device *dev = &pdev->dev;
-
- kirin_pcie->phy_ref_clk = devm_clk_get(dev, "pcie_phy_ref");
- if (IS_ERR(kirin_pcie->phy_ref_clk))
- return PTR_ERR(kirin_pcie->phy_ref_clk);
-
- kirin_pcie->pcie_aux_clk = devm_clk_get(dev, "pcie_aux");
- if (IS_ERR(kirin_pcie->pcie_aux_clk))
- return PTR_ERR(kirin_pcie->pcie_aux_clk);
-
- kirin_pcie->apb_phy_clk = devm_clk_get(dev, "pcie_apb_phy");
- if (IS_ERR(kirin_pcie->apb_phy_clk))
- return PTR_ERR(kirin_pcie->apb_phy_clk);
-
- kirin_pcie->apb_sys_clk = devm_clk_get(dev, "pcie_apb_sys");
- if (IS_ERR(kirin_pcie->apb_sys_clk))
- return PTR_ERR(kirin_pcie->apb_sys_clk);
-
- kirin_pcie->pcie_aclk = devm_clk_get(dev, "pcie_aclk");
- if (IS_ERR(kirin_pcie->pcie_aclk))
- return PTR_ERR(kirin_pcie->pcie_aclk);
-
- return 0;
-}
-
static long kirin_pcie_get_resource(struct kirin_pcie *kirin_pcie,
struct platform_device *pdev)
{
@@ -152,149 +77,18 @@ static long kirin_pcie_get_resource(struct kirin_pcie *kirin_pcie,
if (IS_ERR(kirin_pcie->apb_base))
return PTR_ERR(kirin_pcie->apb_base);
- kirin_pcie->phy_base =
- devm_platform_ioremap_resource_byname(pdev, "phy");
- if (IS_ERR(kirin_pcie->phy_base))
- return PTR_ERR(kirin_pcie->phy_base);
-
- kirin_pcie->crgctrl =
- syscon_regmap_lookup_by_compatible("hisilicon,hi3660-crgctrl");
- if (IS_ERR(kirin_pcie->crgctrl))
- return PTR_ERR(kirin_pcie->crgctrl);
-
- kirin_pcie->sysctrl =
- syscon_regmap_lookup_by_compatible("hisilicon,hi3660-sctrl");
- if (IS_ERR(kirin_pcie->sysctrl))
- return PTR_ERR(kirin_pcie->sysctrl);
-
return 0;
}
-static int kirin_pcie_phy_init(struct kirin_pcie *kirin_pcie)
-{
- struct device *dev = kirin_pcie->pci->dev;
- u32 reg_val;
-
- reg_val = kirin_apb_phy_readl(kirin_pcie, PCIE_APB_PHY_CTRL1);
- reg_val &= ~PHY_REF_PAD_BIT;
- kirin_apb_phy_writel(kirin_pcie, reg_val, PCIE_APB_PHY_CTRL1);
-
- reg_val = kirin_apb_phy_readl(kirin_pcie, PCIE_APB_PHY_CTRL0);
- reg_val &= ~PHY_PWR_DOWN_BIT;
- kirin_apb_phy_writel(kirin_pcie, reg_val, PCIE_APB_PHY_CTRL0);
- usleep_range(TIME_PHY_PD_MIN, TIME_PHY_PD_MAX);
-
- reg_val = kirin_apb_phy_readl(kirin_pcie, PCIE_APB_PHY_CTRL1);
- reg_val &= ~PHY_RST_ACK_BIT;
- kirin_apb_phy_writel(kirin_pcie, reg_val, PCIE_APB_PHY_CTRL1);
-
- usleep_range(PIPE_CLK_WAIT_MIN, PIPE_CLK_WAIT_MAX);
- reg_val = kirin_apb_phy_readl(kirin_pcie, PCIE_APB_PHY_STATUS0);
- if (reg_val & PIPE_CLK_STABLE) {
- dev_err(dev, "PIPE clk is not stable\n");
- return -EINVAL;
- }
-
- return 0;
-}
-
-static void kirin_pcie_oe_enable(struct kirin_pcie *kirin_pcie)
-{
- u32 val;
-
- regmap_read(kirin_pcie->sysctrl, SCTRL_PCIE_OE_OFFSET, &val);
- val |= PCIE_DEBOUNCE_PARAM;
- val &= ~PCIE_OE_BYPASS;
- regmap_write(kirin_pcie->sysctrl, SCTRL_PCIE_OE_OFFSET, val);
-}
-
-static int kirin_pcie_clk_ctrl(struct kirin_pcie *kirin_pcie, bool enable)
-{
- int ret = 0;
-
- if (!enable)
- goto close_clk;
-
- ret = clk_set_rate(kirin_pcie->phy_ref_clk, REF_CLK_FREQ);
- if (ret)
- return ret;
-
- ret = clk_prepare_enable(kirin_pcie->phy_ref_clk);
- if (ret)
- return ret;
-
- ret = clk_prepare_enable(kirin_pcie->apb_sys_clk);
- if (ret)
- goto apb_sys_fail;
-
- ret = clk_prepare_enable(kirin_pcie->apb_phy_clk);
- if (ret)
- goto apb_phy_fail;
-
- ret = clk_prepare_enable(kirin_pcie->pcie_aclk);
- if (ret)
- goto aclk_fail;
-
- ret = clk_prepare_enable(kirin_pcie->pcie_aux_clk);
- if (ret)
- goto aux_clk_fail;
-
- return 0;
-
-close_clk:
- clk_disable_unprepare(kirin_pcie->pcie_aux_clk);
-aux_clk_fail:
- clk_disable_unprepare(kirin_pcie->pcie_aclk);
-aclk_fail:
- clk_disable_unprepare(kirin_pcie->apb_phy_clk);
-apb_phy_fail:
- clk_disable_unprepare(kirin_pcie->apb_sys_clk);
-apb_sys_fail:
- clk_disable_unprepare(kirin_pcie->phy_ref_clk);
-
- return ret;
-}
-
static int kirin_pcie_power_on(struct kirin_pcie *kirin_pcie)
{
int ret;
- /* Power supply for Host */
- regmap_write(kirin_pcie->sysctrl,
- SCTRL_PCIE_CMOS_OFFSET, SCTRL_PCIE_CMOS_BIT);
- usleep_range(TIME_CMOS_MIN, TIME_CMOS_MAX);
- kirin_pcie_oe_enable(kirin_pcie);
-
- ret = kirin_pcie_clk_ctrl(kirin_pcie, true);
+ ret = phy_init(kirin_pcie->phy);
if (ret)
return ret;
- /* ISO disable, PCIeCtrl, PHY assert and clk gate clear */
- regmap_write(kirin_pcie->sysctrl,
- SCTRL_PCIE_ISO_OFFSET, SCTRL_PCIE_ISO_BIT);
- regmap_write(kirin_pcie->crgctrl,
- CRGCTRL_PCIE_ASSERT_OFFSET, CRGCTRL_PCIE_ASSERT_BIT);
- regmap_write(kirin_pcie->sysctrl,
- SCTRL_PCIE_HPCLK_OFFSET, SCTRL_PCIE_HPCLK_BIT);
-
- ret = kirin_pcie_phy_init(kirin_pcie);
- if (ret)
- goto close_clk;
-
- /* perst assert Endpoint */
- if (!gpio_request(kirin_pcie->gpio_id_reset, "pcie_perst")) {
- usleep_range(REF_2_PERST_MIN, REF_2_PERST_MAX);
- ret = gpio_direction_output(kirin_pcie->gpio_id_reset, 1);
- if (ret)
- goto close_clk;
- usleep_range(PERST_2_ACCESS_MIN, PERST_2_ACCESS_MAX);
-
- return 0;
- }
-
-close_clk:
- kirin_pcie_clk_ctrl(kirin_pcie, false);
- return ret;
+ return phy_power_on(kirin_pcie->phy);
}
static void kirin_pcie_sideband_dbi_w_mode(struct kirin_pcie *kirin_pcie,
@@ -444,30 +238,41 @@ static int kirin_pcie_probe(struct platform_device *pdev)
pci->pp.ops = &kirin_pcie_host_ops;
kirin_pcie->pci = pci;
- ret = kirin_pcie_get_clk(kirin_pcie, pdev);
- if (ret)
- return ret;
+ kirin_pcie->phy = devm_of_phy_get(dev, dev->of_node, NULL);
+ if (IS_ERR(kirin_pcie->phy))
+ return PTR_ERR(kirin_pcie->phy);
ret = kirin_pcie_get_resource(kirin_pcie, pdev);
if (ret)
return ret;
- kirin_pcie->gpio_id_reset = of_get_named_gpio(dev->of_node,
- "reset-gpios", 0);
- if (kirin_pcie->gpio_id_reset == -EPROBE_DEFER) {
- return -EPROBE_DEFER;
- } else if (!gpio_is_valid(kirin_pcie->gpio_id_reset)) {
- dev_err(dev, "unable to get a valid gpio pin\n");
- return -ENODEV;
- }
-
ret = kirin_pcie_power_on(kirin_pcie);
if (ret)
return ret;
platform_set_drvdata(pdev, kirin_pcie);
- return dw_pcie_host_init(&pci->pp);
+ ret = dw_pcie_host_init(&pci->pp);
+ if (ret) {
+ phy_power_off(kirin_pcie->phy);
+ goto err;
+ }
+
+ return 0;
+err:
+ phy_exit(kirin_pcie->phy);
+
+ return ret;
+}
+
+static int __exit kirin_pcie_remove(struct platform_device *pdev)
+{
+ struct kirin_pcie *kirin_pcie = platform_get_drvdata(pdev);
+
+ phy_power_off(kirin_pcie->phy);
+ phy_exit(kirin_pcie->phy);
+
+ return 0;
}
static const struct of_device_id kirin_pcie_match[] = {
@@ -478,6 +283,7 @@ static const struct of_device_id kirin_pcie_match[] = {
static struct platform_driver kirin_pcie_driver = {
.probe = kirin_pcie_probe,
+ .remove = __exit_p(kirin_pcie_remove),
.driver = {
.name = "kirin-pcie",
.of_match_table = kirin_pcie_match,
--
2.31.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 7/8] PCI: kirin: Drop the PHY logic from the driver
@ 2021-07-12 21:46 ` Mauro Carvalho Chehab
0 siblings, 0 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-12 21:46 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
Krzysztof Wilczyński, Manivannan Sadhasivam, Rob Herring,
Binghui Wang, Bjorn Helgaas, Lorenzo Pieralisi, Rob Herring,
Wei Xu, Xiaowei Song, devicetree, linux-arm-kernel, linux-kernel,
linux-pci
The pcie-kirin PCIe driver contains internally a PHY interface for
a Kirin 960. Drop it and add support for using the new PHY driver
for Kirin 960, updating DT accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 29 ++-
drivers/pci/controller/dwc/pcie-kirin.c | 252 +++-------------------
2 files changed, 47 insertions(+), 234 deletions(-)
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
index f1ec87c05842..772bb632814f 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
@@ -995,17 +995,33 @@ spi3: spi@ff3b3000 {
status = "disabled";
};
+ pcie_phy: pcie-phy@f3f2000 {
+ compatible = "hisilicon,hi960-pcie-phy";
+ reg = <0x0 0xf3f20000 0x0 0x40000>;
+ reg-names = "phy";
+ clocks = <&crg_ctrl HI3660_PCIEPHY_REF>,
+ <&crg_ctrl HI3660_CLK_GATE_PCIEAUX>,
+ <&crg_ctrl HI3660_PCLK_GATE_PCIE_PHY>,
+ <&crg_ctrl HI3660_PCLK_GATE_PCIE_SYS>,
+ <&crg_ctrl HI3660_ACLK_GATE_PCIE>;
+ clock-names = "pcie_phy_ref", "pcie_aux",
+ "pcie_apb_phy", "pcie_apb_sys",
+ "pcie_aclk";
+ reset-gpios = <&gpio11 1 0 >;
+ #phy-cells = <0>;
+ };
+
pcie@f4000000 {
compatible = "hisilicon,kirin960-pcie";
reg = <0x0 0xf4000000 0x0 0x1000>,
<0x0 0xff3fe000 0x0 0x1000>,
- <0x0 0xf3f20000 0x0 0x40000>,
<0x0 0xf5000000 0x0 0x2000>;
- reg-names = "dbi", "apb", "phy", "config";
+ reg-names = "dbi", "apb", "config";
bus-range = <0x0 0x1>;
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
+ phys = <&pcie_phy>;
ranges = <0x02000000 0x0 0x00000000
0x0 0xf6000000
0x0 0x02000000>;
@@ -1022,15 +1038,6 @@ &gic GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
&gic GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
<0x0 0 0 4
&gic GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&crg_ctrl HI3660_PCIEPHY_REF>,
- <&crg_ctrl HI3660_CLK_GATE_PCIEAUX>,
- <&crg_ctrl HI3660_PCLK_GATE_PCIE_PHY>,
- <&crg_ctrl HI3660_PCLK_GATE_PCIE_SYS>,
- <&crg_ctrl HI3660_ACLK_GATE_PCIE>;
- clock-names = "pcie_phy_ref", "pcie_aux",
- "pcie_apb_phy", "pcie_apb_sys",
- "pcie_aclk";
- reset-gpios = <&gpio11 1 0 >;
};
/* UFS */
diff --git a/drivers/pci/controller/dwc/pcie-kirin.c b/drivers/pci/controller/dwc/pcie-kirin.c
index 7b0f87535960..66662f7b0fc9 100644
--- a/drivers/pci/controller/dwc/pcie-kirin.c
+++ b/drivers/pci/controller/dwc/pcie-kirin.c
@@ -9,7 +9,6 @@
*/
#include <linux/compiler.h>
-#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/gpio.h>
@@ -21,6 +20,7 @@
#include <linux/pci.h>
#include <linux/pci_regs.h>
#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
#include <linux/regmap.h>
#include <linux/resource.h>
#include <linux/types.h>
@@ -28,26 +28,17 @@
#define to_kirin_pcie(x) dev_get_drvdata((x)->dev)
-#define REF_CLK_FREQ 100000000
-
/* PCIe ELBI registers */
#define SOC_PCIECTRL_CTRL0_ADDR 0x000
#define SOC_PCIECTRL_CTRL1_ADDR 0x004
-#define SOC_PCIEPHY_CTRL2_ADDR 0x008
-#define SOC_PCIEPHY_CTRL3_ADDR 0x00c
#define PCIE_ELBI_SLV_DBI_ENABLE (0x1 << 21)
/* info located in APB */
#define PCIE_APP_LTSSM_ENABLE 0x01c
-#define PCIE_APB_PHY_CTRL0 0x0
-#define PCIE_APB_PHY_CTRL1 0x4
#define PCIE_APB_PHY_STATUS0 0x400
#define PCIE_LINKUP_ENABLE (0x8020)
#define PCIE_LTSSM_ENABLE_BIT (0x1 << 11)
#define PIPE_CLK_STABLE (0x1 << 19)
-#define PHY_REF_PAD_BIT (0x1 << 8)
-#define PHY_PWR_DOWN_BIT (0x1 << 22)
-#define PHY_RST_ACK_BIT (0x1 << 16)
/* info located in sysctrl */
#define SCTRL_PCIE_CMOS_OFFSET 0x60
@@ -60,36 +51,10 @@
#define PCIE_DEBOUNCE_PARAM 0xF0F400
#define PCIE_OE_BYPASS (0x3 << 28)
-/* peri_crg ctrl */
-#define CRGCTRL_PCIE_ASSERT_OFFSET 0x88
-#define CRGCTRL_PCIE_ASSERT_BIT 0x8c000000
-
-/* Time for delay */
-#define REF_2_PERST_MIN 20000
-#define REF_2_PERST_MAX 25000
-#define PERST_2_ACCESS_MIN 10000
-#define PERST_2_ACCESS_MAX 12000
-#define LINK_WAIT_MIN 900
-#define LINK_WAIT_MAX 1000
-#define PIPE_CLK_WAIT_MIN 550
-#define PIPE_CLK_WAIT_MAX 600
-#define TIME_CMOS_MIN 100
-#define TIME_CMOS_MAX 105
-#define TIME_PHY_PD_MIN 10
-#define TIME_PHY_PD_MAX 11
-
struct kirin_pcie {
struct dw_pcie *pci;
+ struct phy *phy;
void __iomem *apb_base;
- void __iomem *phy_base;
- struct regmap *crgctrl;
- struct regmap *sysctrl;
- struct clk *apb_sys_clk;
- struct clk *apb_phy_clk;
- struct clk *phy_ref_clk;
- struct clk *pcie_aclk;
- struct clk *pcie_aux_clk;
- int gpio_id_reset;
};
/* Registers in PCIeCTRL */
@@ -104,46 +69,6 @@ static inline u32 kirin_apb_ctrl_readl(struct kirin_pcie *kirin_pcie, u32 reg)
return readl(kirin_pcie->apb_base + reg);
}
-/* Registers in PCIePHY */
-static inline void kirin_apb_phy_writel(struct kirin_pcie *kirin_pcie,
- u32 val, u32 reg)
-{
- writel(val, kirin_pcie->phy_base + reg);
-}
-
-static inline u32 kirin_apb_phy_readl(struct kirin_pcie *kirin_pcie, u32 reg)
-{
- return readl(kirin_pcie->phy_base + reg);
-}
-
-static long kirin_pcie_get_clk(struct kirin_pcie *kirin_pcie,
- struct platform_device *pdev)
-{
- struct device *dev = &pdev->dev;
-
- kirin_pcie->phy_ref_clk = devm_clk_get(dev, "pcie_phy_ref");
- if (IS_ERR(kirin_pcie->phy_ref_clk))
- return PTR_ERR(kirin_pcie->phy_ref_clk);
-
- kirin_pcie->pcie_aux_clk = devm_clk_get(dev, "pcie_aux");
- if (IS_ERR(kirin_pcie->pcie_aux_clk))
- return PTR_ERR(kirin_pcie->pcie_aux_clk);
-
- kirin_pcie->apb_phy_clk = devm_clk_get(dev, "pcie_apb_phy");
- if (IS_ERR(kirin_pcie->apb_phy_clk))
- return PTR_ERR(kirin_pcie->apb_phy_clk);
-
- kirin_pcie->apb_sys_clk = devm_clk_get(dev, "pcie_apb_sys");
- if (IS_ERR(kirin_pcie->apb_sys_clk))
- return PTR_ERR(kirin_pcie->apb_sys_clk);
-
- kirin_pcie->pcie_aclk = devm_clk_get(dev, "pcie_aclk");
- if (IS_ERR(kirin_pcie->pcie_aclk))
- return PTR_ERR(kirin_pcie->pcie_aclk);
-
- return 0;
-}
-
static long kirin_pcie_get_resource(struct kirin_pcie *kirin_pcie,
struct platform_device *pdev)
{
@@ -152,149 +77,18 @@ static long kirin_pcie_get_resource(struct kirin_pcie *kirin_pcie,
if (IS_ERR(kirin_pcie->apb_base))
return PTR_ERR(kirin_pcie->apb_base);
- kirin_pcie->phy_base =
- devm_platform_ioremap_resource_byname(pdev, "phy");
- if (IS_ERR(kirin_pcie->phy_base))
- return PTR_ERR(kirin_pcie->phy_base);
-
- kirin_pcie->crgctrl =
- syscon_regmap_lookup_by_compatible("hisilicon,hi3660-crgctrl");
- if (IS_ERR(kirin_pcie->crgctrl))
- return PTR_ERR(kirin_pcie->crgctrl);
-
- kirin_pcie->sysctrl =
- syscon_regmap_lookup_by_compatible("hisilicon,hi3660-sctrl");
- if (IS_ERR(kirin_pcie->sysctrl))
- return PTR_ERR(kirin_pcie->sysctrl);
-
return 0;
}
-static int kirin_pcie_phy_init(struct kirin_pcie *kirin_pcie)
-{
- struct device *dev = kirin_pcie->pci->dev;
- u32 reg_val;
-
- reg_val = kirin_apb_phy_readl(kirin_pcie, PCIE_APB_PHY_CTRL1);
- reg_val &= ~PHY_REF_PAD_BIT;
- kirin_apb_phy_writel(kirin_pcie, reg_val, PCIE_APB_PHY_CTRL1);
-
- reg_val = kirin_apb_phy_readl(kirin_pcie, PCIE_APB_PHY_CTRL0);
- reg_val &= ~PHY_PWR_DOWN_BIT;
- kirin_apb_phy_writel(kirin_pcie, reg_val, PCIE_APB_PHY_CTRL0);
- usleep_range(TIME_PHY_PD_MIN, TIME_PHY_PD_MAX);
-
- reg_val = kirin_apb_phy_readl(kirin_pcie, PCIE_APB_PHY_CTRL1);
- reg_val &= ~PHY_RST_ACK_BIT;
- kirin_apb_phy_writel(kirin_pcie, reg_val, PCIE_APB_PHY_CTRL1);
-
- usleep_range(PIPE_CLK_WAIT_MIN, PIPE_CLK_WAIT_MAX);
- reg_val = kirin_apb_phy_readl(kirin_pcie, PCIE_APB_PHY_STATUS0);
- if (reg_val & PIPE_CLK_STABLE) {
- dev_err(dev, "PIPE clk is not stable\n");
- return -EINVAL;
- }
-
- return 0;
-}
-
-static void kirin_pcie_oe_enable(struct kirin_pcie *kirin_pcie)
-{
- u32 val;
-
- regmap_read(kirin_pcie->sysctrl, SCTRL_PCIE_OE_OFFSET, &val);
- val |= PCIE_DEBOUNCE_PARAM;
- val &= ~PCIE_OE_BYPASS;
- regmap_write(kirin_pcie->sysctrl, SCTRL_PCIE_OE_OFFSET, val);
-}
-
-static int kirin_pcie_clk_ctrl(struct kirin_pcie *kirin_pcie, bool enable)
-{
- int ret = 0;
-
- if (!enable)
- goto close_clk;
-
- ret = clk_set_rate(kirin_pcie->phy_ref_clk, REF_CLK_FREQ);
- if (ret)
- return ret;
-
- ret = clk_prepare_enable(kirin_pcie->phy_ref_clk);
- if (ret)
- return ret;
-
- ret = clk_prepare_enable(kirin_pcie->apb_sys_clk);
- if (ret)
- goto apb_sys_fail;
-
- ret = clk_prepare_enable(kirin_pcie->apb_phy_clk);
- if (ret)
- goto apb_phy_fail;
-
- ret = clk_prepare_enable(kirin_pcie->pcie_aclk);
- if (ret)
- goto aclk_fail;
-
- ret = clk_prepare_enable(kirin_pcie->pcie_aux_clk);
- if (ret)
- goto aux_clk_fail;
-
- return 0;
-
-close_clk:
- clk_disable_unprepare(kirin_pcie->pcie_aux_clk);
-aux_clk_fail:
- clk_disable_unprepare(kirin_pcie->pcie_aclk);
-aclk_fail:
- clk_disable_unprepare(kirin_pcie->apb_phy_clk);
-apb_phy_fail:
- clk_disable_unprepare(kirin_pcie->apb_sys_clk);
-apb_sys_fail:
- clk_disable_unprepare(kirin_pcie->phy_ref_clk);
-
- return ret;
-}
-
static int kirin_pcie_power_on(struct kirin_pcie *kirin_pcie)
{
int ret;
- /* Power supply for Host */
- regmap_write(kirin_pcie->sysctrl,
- SCTRL_PCIE_CMOS_OFFSET, SCTRL_PCIE_CMOS_BIT);
- usleep_range(TIME_CMOS_MIN, TIME_CMOS_MAX);
- kirin_pcie_oe_enable(kirin_pcie);
-
- ret = kirin_pcie_clk_ctrl(kirin_pcie, true);
+ ret = phy_init(kirin_pcie->phy);
if (ret)
return ret;
- /* ISO disable, PCIeCtrl, PHY assert and clk gate clear */
- regmap_write(kirin_pcie->sysctrl,
- SCTRL_PCIE_ISO_OFFSET, SCTRL_PCIE_ISO_BIT);
- regmap_write(kirin_pcie->crgctrl,
- CRGCTRL_PCIE_ASSERT_OFFSET, CRGCTRL_PCIE_ASSERT_BIT);
- regmap_write(kirin_pcie->sysctrl,
- SCTRL_PCIE_HPCLK_OFFSET, SCTRL_PCIE_HPCLK_BIT);
-
- ret = kirin_pcie_phy_init(kirin_pcie);
- if (ret)
- goto close_clk;
-
- /* perst assert Endpoint */
- if (!gpio_request(kirin_pcie->gpio_id_reset, "pcie_perst")) {
- usleep_range(REF_2_PERST_MIN, REF_2_PERST_MAX);
- ret = gpio_direction_output(kirin_pcie->gpio_id_reset, 1);
- if (ret)
- goto close_clk;
- usleep_range(PERST_2_ACCESS_MIN, PERST_2_ACCESS_MAX);
-
- return 0;
- }
-
-close_clk:
- kirin_pcie_clk_ctrl(kirin_pcie, false);
- return ret;
+ return phy_power_on(kirin_pcie->phy);
}
static void kirin_pcie_sideband_dbi_w_mode(struct kirin_pcie *kirin_pcie,
@@ -444,30 +238,41 @@ static int kirin_pcie_probe(struct platform_device *pdev)
pci->pp.ops = &kirin_pcie_host_ops;
kirin_pcie->pci = pci;
- ret = kirin_pcie_get_clk(kirin_pcie, pdev);
- if (ret)
- return ret;
+ kirin_pcie->phy = devm_of_phy_get(dev, dev->of_node, NULL);
+ if (IS_ERR(kirin_pcie->phy))
+ return PTR_ERR(kirin_pcie->phy);
ret = kirin_pcie_get_resource(kirin_pcie, pdev);
if (ret)
return ret;
- kirin_pcie->gpio_id_reset = of_get_named_gpio(dev->of_node,
- "reset-gpios", 0);
- if (kirin_pcie->gpio_id_reset == -EPROBE_DEFER) {
- return -EPROBE_DEFER;
- } else if (!gpio_is_valid(kirin_pcie->gpio_id_reset)) {
- dev_err(dev, "unable to get a valid gpio pin\n");
- return -ENODEV;
- }
-
ret = kirin_pcie_power_on(kirin_pcie);
if (ret)
return ret;
platform_set_drvdata(pdev, kirin_pcie);
- return dw_pcie_host_init(&pci->pp);
+ ret = dw_pcie_host_init(&pci->pp);
+ if (ret) {
+ phy_power_off(kirin_pcie->phy);
+ goto err;
+ }
+
+ return 0;
+err:
+ phy_exit(kirin_pcie->phy);
+
+ return ret;
+}
+
+static int __exit kirin_pcie_remove(struct platform_device *pdev)
+{
+ struct kirin_pcie *kirin_pcie = platform_get_drvdata(pdev);
+
+ phy_power_off(kirin_pcie->phy);
+ phy_exit(kirin_pcie->phy);
+
+ return 0;
}
static const struct of_device_id kirin_pcie_match[] = {
@@ -478,6 +283,7 @@ static const struct of_device_id kirin_pcie_match[] = {
static struct platform_driver kirin_pcie_driver = {
.probe = kirin_pcie_probe,
+ .remove = __exit_p(kirin_pcie_remove),
.driver = {
.name = "kirin-pcie",
.of_match_table = kirin_pcie_match,
--
2.31.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v4 8/8] PCI: kirin: Use regmap for APB registers
2021-07-12 21:46 ` Mauro Carvalho Chehab
` (8 preceding siblings ...)
(?)
@ 2021-07-12 21:46 ` Mauro Carvalho Chehab
-1 siblings, 0 replies; 18+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-12 21:46 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
Krzysztof Wilczyński, Manivannan Sadhasivam, Rob Herring,
Binghui Wang, Bjorn Helgaas, Lorenzo Pieralisi, Xiaowei Song,
linux-kernel, linux-pci
The PHY layer need to access APB registers too, for Kirin 970.
So, place them into a named regmap.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
drivers/pci/controller/dwc/pcie-kirin.c | 49 +++++++++++++------------
1 file changed, 26 insertions(+), 23 deletions(-)
diff --git a/drivers/pci/controller/dwc/pcie-kirin.c b/drivers/pci/controller/dwc/pcie-kirin.c
index 66662f7b0fc9..c51745f9b56b 100644
--- a/drivers/pci/controller/dwc/pcie-kirin.c
+++ b/drivers/pci/controller/dwc/pcie-kirin.c
@@ -54,28 +54,30 @@
struct kirin_pcie {
struct dw_pcie *pci;
struct phy *phy;
- void __iomem *apb_base;
+ struct regmap *apb;
};
-/* Registers in PCIeCTRL */
-static inline void kirin_apb_ctrl_writel(struct kirin_pcie *kirin_pcie,
- u32 val, u32 reg)
-{
- writel(val, kirin_pcie->apb_base + reg);
-}
-
-static inline u32 kirin_apb_ctrl_readl(struct kirin_pcie *kirin_pcie, u32 reg)
-{
- return readl(kirin_pcie->apb_base + reg);
-}
+static const struct regmap_config pcie_kirin_regmap_conf = {
+ .name = "kirin_pcie_apb",
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
static long kirin_pcie_get_resource(struct kirin_pcie *kirin_pcie,
struct platform_device *pdev)
{
- kirin_pcie->apb_base =
- devm_platform_ioremap_resource_byname(pdev, "apb");
- if (IS_ERR(kirin_pcie->apb_base))
- return PTR_ERR(kirin_pcie->apb_base);
+ struct device *dev = &pdev->dev;
+ void __iomem *apb_base;
+
+ apb_base = devm_platform_ioremap_resource_byname(pdev, "apb");
+ if (IS_ERR(apb_base))
+ return PTR_ERR(apb_base);
+
+ kirin_pcie->apb = devm_regmap_init_mmio(dev, apb_base,
+ &pcie_kirin_regmap_conf);
+ if (IS_ERR(kirin_pcie->apb))
+ return PTR_ERR(kirin_pcie->apb);
return 0;
}
@@ -96,13 +98,13 @@ static void kirin_pcie_sideband_dbi_w_mode(struct kirin_pcie *kirin_pcie,
{
u32 val;
- val = kirin_apb_ctrl_readl(kirin_pcie, SOC_PCIECTRL_CTRL0_ADDR);
+ regmap_read(kirin_pcie->apb, SOC_PCIECTRL_CTRL0_ADDR, &val);
if (on)
val = val | PCIE_ELBI_SLV_DBI_ENABLE;
else
val = val & ~PCIE_ELBI_SLV_DBI_ENABLE;
- kirin_apb_ctrl_writel(kirin_pcie, val, SOC_PCIECTRL_CTRL0_ADDR);
+ regmap_write(kirin_pcie->apb, SOC_PCIECTRL_CTRL0_ADDR, val);
}
static void kirin_pcie_sideband_dbi_r_mode(struct kirin_pcie *kirin_pcie,
@@ -110,13 +112,13 @@ static void kirin_pcie_sideband_dbi_r_mode(struct kirin_pcie *kirin_pcie,
{
u32 val;
- val = kirin_apb_ctrl_readl(kirin_pcie, SOC_PCIECTRL_CTRL1_ADDR);
+ regmap_read(kirin_pcie->apb, SOC_PCIECTRL_CTRL1_ADDR, &val);
if (on)
val = val | PCIE_ELBI_SLV_DBI_ENABLE;
else
val = val & ~PCIE_ELBI_SLV_DBI_ENABLE;
- kirin_apb_ctrl_writel(kirin_pcie, val, SOC_PCIECTRL_CTRL1_ADDR);
+ regmap_write(kirin_pcie->apb, SOC_PCIECTRL_CTRL1_ADDR, val);
}
static int kirin_pcie_rd_own_conf(struct pci_bus *bus, unsigned int devfn,
@@ -176,8 +178,9 @@ static void kirin_pcie_write_dbi(struct dw_pcie *pci, void __iomem *base,
static int kirin_pcie_link_up(struct dw_pcie *pci)
{
struct kirin_pcie *kirin_pcie = to_kirin_pcie(pci);
- u32 val = kirin_apb_ctrl_readl(kirin_pcie, PCIE_APB_PHY_STATUS0);
+ u32 val;
+ regmap_read(kirin_pcie->apb, PCIE_APB_PHY_STATUS0, &val);
if ((val & PCIE_LINKUP_ENABLE) == PCIE_LINKUP_ENABLE)
return 1;
@@ -189,8 +192,8 @@ static int kirin_pcie_start_link(struct dw_pcie *pci)
struct kirin_pcie *kirin_pcie = to_kirin_pcie(pci);
/* assert LTSSM enable */
- kirin_apb_ctrl_writel(kirin_pcie, PCIE_LTSSM_ENABLE_BIT,
- PCIE_APP_LTSSM_ENABLE);
+ regmap_write(kirin_pcie->apb, PCIE_APP_LTSSM_ENABLE,
+ PCIE_LTSSM_ENABLE_BIT);
return 0;
}
--
2.31.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH v4 6/8] phy: HiSilicon: add driver for Kirin 970 PCIe PHY
2021-07-12 21:46 ` Mauro Carvalho Chehab
@ 2021-07-13 2:03 ` kernel test robot
-1 siblings, 0 replies; 18+ messages in thread
From: kernel test robot @ 2021-07-13 2:03 UTC (permalink / raw)
To: Mauro Carvalho Chehab, Bjorn Helgaas
Cc: kbuild-all, linux-media, linuxarm, mauro.chehab,
Mauro Carvalho Chehab, Krzysztof Wilczyński,
Manivannan Sadhasivam, Rob Herring, Binghui Wang,
Greg Kroah-Hartman
[-- Attachment #1: Type: text/plain, Size: 2800 bytes --]
Hi Mauro,
I love your patch! Perhaps something to improve:
[auto build test WARNING on pci/next]
[also build test WARNING on robh/for-next linus/master v5.14-rc1 next-20210712]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Mauro-Carvalho-Chehab/Add-support-for-Hikey-970-PCIe/20210713-054716
base: https://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci.git next
config: sh-allmodconfig (attached as .config)
compiler: sh4-linux-gcc (GCC) 9.3.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# https://github.com/0day-ci/linux/commit/c1d16aeb1efc7e49da9c7222fc98efcc07ddb5c3
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Mauro-Carvalho-Chehab/Add-support-for-Hikey-970-PCIe/20210713-054716
git checkout c1d16aeb1efc7e49da9c7222fc98efcc07ddb5c3
# save the attached .config to linux build tree
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-9.3.0 make.cross ARCH=sh
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
All warnings (new ones prefixed by >>):
>> drivers/phy/hisilicon/phy-hi3670-pcie.c:178:6: warning: no previous prototype for 'hi3670_pcie_get_eyeparam' [-Wmissing-prototypes]
178 | void hi3670_pcie_get_eyeparam(struct hi3670_pcie_phy *phy)
| ^~~~~~~~~~~~~~~~~~~~~~~~
Kconfig warnings: (for reference only)
WARNING: unmet direct dependencies detected for SND_ATMEL_SOC_PDC
Depends on SOUND && !UML && SND && SND_SOC && SND_ATMEL_SOC && HAS_DMA
Selected by
- SND_ATMEL_SOC_SSC && SOUND && !UML && SND && SND_SOC && SND_ATMEL_SOC
- SND_ATMEL_SOC_SSC_PDC && SOUND && !UML && SND && SND_SOC && SND_ATMEL_SOC && ATMEL_SSC
vim +/hi3670_pcie_get_eyeparam +178 drivers/phy/hisilicon/phy-hi3670-pcie.c
177
> 178 void hi3670_pcie_get_eyeparam(struct hi3670_pcie_phy *phy)
179 {
180 struct device *dev = phy->dev;
181 struct device_node *np;
182 int ret, i;
183
184 np = dev->of_node;
185
186 ret = of_property_read_u32_array(np, "hisilicon,eye-diagram-param",
187 phy->eye_param, NUM_EYEPARAM);
188 if (!ret)
189 return;
190
191 /* There's no optional eye_param property. Set array to default */
192 for (i = 0; i < NUM_EYEPARAM; i++)
193 phy->eye_param[i] = EYEPARAM_NOCFG;
194 }
195
---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 55109 bytes --]
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v4 6/8] phy: HiSilicon: add driver for Kirin 970 PCIe PHY
@ 2021-07-13 2:03 ` kernel test robot
0 siblings, 0 replies; 18+ messages in thread
From: kernel test robot @ 2021-07-13 2:03 UTC (permalink / raw)
To: kbuild-all
[-- Attachment #1: Type: text/plain, Size: 2868 bytes --]
Hi Mauro,
I love your patch! Perhaps something to improve:
[auto build test WARNING on pci/next]
[also build test WARNING on robh/for-next linus/master v5.14-rc1 next-20210712]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Mauro-Carvalho-Chehab/Add-support-for-Hikey-970-PCIe/20210713-054716
base: https://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci.git next
config: sh-allmodconfig (attached as .config)
compiler: sh4-linux-gcc (GCC) 9.3.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# https://github.com/0day-ci/linux/commit/c1d16aeb1efc7e49da9c7222fc98efcc07ddb5c3
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Mauro-Carvalho-Chehab/Add-support-for-Hikey-970-PCIe/20210713-054716
git checkout c1d16aeb1efc7e49da9c7222fc98efcc07ddb5c3
# save the attached .config to linux build tree
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-9.3.0 make.cross ARCH=sh
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
All warnings (new ones prefixed by >>):
>> drivers/phy/hisilicon/phy-hi3670-pcie.c:178:6: warning: no previous prototype for 'hi3670_pcie_get_eyeparam' [-Wmissing-prototypes]
178 | void hi3670_pcie_get_eyeparam(struct hi3670_pcie_phy *phy)
| ^~~~~~~~~~~~~~~~~~~~~~~~
Kconfig warnings: (for reference only)
WARNING: unmet direct dependencies detected for SND_ATMEL_SOC_PDC
Depends on SOUND && !UML && SND && SND_SOC && SND_ATMEL_SOC && HAS_DMA
Selected by
- SND_ATMEL_SOC_SSC && SOUND && !UML && SND && SND_SOC && SND_ATMEL_SOC
- SND_ATMEL_SOC_SSC_PDC && SOUND && !UML && SND && SND_SOC && SND_ATMEL_SOC && ATMEL_SSC
vim +/hi3670_pcie_get_eyeparam +178 drivers/phy/hisilicon/phy-hi3670-pcie.c
177
> 178 void hi3670_pcie_get_eyeparam(struct hi3670_pcie_phy *phy)
179 {
180 struct device *dev = phy->dev;
181 struct device_node *np;
182 int ret, i;
183
184 np = dev->of_node;
185
186 ret = of_property_read_u32_array(np, "hisilicon,eye-diagram-param",
187 phy->eye_param, NUM_EYEPARAM);
188 if (!ret)
189 return;
190
191 /* There's no optional eye_param property. Set array to default */
192 for (i = 0; i < NUM_EYEPARAM; i++)
193 phy->eye_param[i] = EYEPARAM_NOCFG;
194 }
195
---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all(a)lists.01.org
[-- Attachment #2: config.gz --]
[-- Type: application/gzip, Size: 55109 bytes --]
^ permalink raw reply [flat|nested] 18+ messages in thread
end of thread, other threads:[~2021-07-13 2:04 UTC | newest]
Thread overview: 18+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-07-12 21:46 [PATCH v4 0/8] Add support for Hikey 970 PCIe Mauro Carvalho Chehab
2021-07-12 21:46 ` Mauro Carvalho Chehab
2021-07-12 21:46 ` Mauro Carvalho Chehab
2021-07-12 21:46 ` [PATCH v4 1/8] dt-bindings: phy: Add bindings for HiKey 960 PCIe PHY Mauro Carvalho Chehab
2021-07-12 21:46 ` Mauro Carvalho Chehab
2021-07-12 21:46 ` [PATCH v4 2/8] dt-bindings: phy: Add bindings for HiKey 970 " Mauro Carvalho Chehab
2021-07-12 21:46 ` Mauro Carvalho Chehab
2021-07-12 21:46 ` [PATCH v4 3/8] dt-bindings: PCI: kirin: Fix compatible string Mauro Carvalho Chehab
2021-07-12 21:46 ` [PATCH v4 4/8] dt-bindings: PCI: kirin: Drop PHY properties Mauro Carvalho Chehab
2021-07-12 21:46 ` [PATCH v4 5/8] phy: HiSilicon: Add driver for Kirin 960 PCIe PHY Mauro Carvalho Chehab
2021-07-12 21:46 ` Mauro Carvalho Chehab
2021-07-12 21:46 ` [PATCH v4 6/8] phy: HiSilicon: add driver for Kirin 970 " Mauro Carvalho Chehab
2021-07-12 21:46 ` Mauro Carvalho Chehab
2021-07-13 2:03 ` kernel test robot
2021-07-13 2:03 ` kernel test robot
2021-07-12 21:46 ` [PATCH v4 7/8] PCI: kirin: Drop the PHY logic from the driver Mauro Carvalho Chehab
2021-07-12 21:46 ` Mauro Carvalho Chehab
2021-07-12 21:46 ` [PATCH v4 8/8] PCI: kirin: Use regmap for APB registers Mauro Carvalho Chehab
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.