* [PATCH v5 0/7] Allwinner H5 and Orange Pi PC2 support
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
Allwinner H5 is a 64-bit SoC with a design like the 32-bit
H3.
This patchset adds support for it, along with the first available
board -- Orange Pi PC2.
Andre Przywara (3):
arm: dts: sun8i: split Allwinner H3 .dtsi
arm64: dts: allwinner: add Allwinner H5 .dtsi
arm64: dts: sunxi: add support for the Orange Pi PC 2 board
Icenowy Zheng (4):
arm64: allwinner: Kconfig: add essential pinctrl driver for H5
clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
clk: sunxi-ng: add support for Allwinner H5 SoC
ARM: dts: sun8i: convert H3 dtsi to use new sunxi-h3-h5 binding header
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
arch/arm/boot/dts/sun8i-h3.dtsi | 589 ++-------------------
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 575 ++++++++++++++++++++
arch/arm64/Kconfig.platforms | 5 +-
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 164 ++++++
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 139 +++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
drivers/clk/sunxi-ng/Kconfig | 6 +-
drivers/clk/sunxi-ng/Makefile | 2 +-
.../sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} | 339 +++++++++++-
.../sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} | 13 +-
.../clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 11 +-
.../reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 11 +-
14 files changed, 1277 insertions(+), 580 deletions(-)
create mode 100644 arch/arm/boot/dts/sunxi-h3-h5.dtsi
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} (71%)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} (83%)
rename include/dt-bindings/clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (95%)
rename include/dt-bindings/reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (94%)
--
2.11.1
^ permalink raw reply [flat|nested] 62+ messages in thread
* [PATCH v5 0/7] Allwinner H5 and Orange Pi PC2 support
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara
Cc: devicetree, linux-kernel, linux-sunxi, Icenowy Zheng, linux-clk,
linux-arm-kernel
Allwinner H5 is a 64-bit SoC with a design like the 32-bit
H3.
This patchset adds support for it, along with the first available
board -- Orange Pi PC2.
Andre Przywara (3):
arm: dts: sun8i: split Allwinner H3 .dtsi
arm64: dts: allwinner: add Allwinner H5 .dtsi
arm64: dts: sunxi: add support for the Orange Pi PC 2 board
Icenowy Zheng (4):
arm64: allwinner: Kconfig: add essential pinctrl driver for H5
clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
clk: sunxi-ng: add support for Allwinner H5 SoC
ARM: dts: sun8i: convert H3 dtsi to use new sunxi-h3-h5 binding header
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
arch/arm/boot/dts/sun8i-h3.dtsi | 589 ++-------------------
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 575 ++++++++++++++++++++
arch/arm64/Kconfig.platforms | 5 +-
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 164 ++++++
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 139 +++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
drivers/clk/sunxi-ng/Kconfig | 6 +-
drivers/clk/sunxi-ng/Makefile | 2 +-
.../sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} | 339 +++++++++++-
.../sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} | 13 +-
.../clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 11 +-
.../reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 11 +-
14 files changed, 1277 insertions(+), 580 deletions(-)
create mode 100644 arch/arm/boot/dts/sunxi-h3-h5.dtsi
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} (71%)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} (83%)
rename include/dt-bindings/clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (95%)
rename include/dt-bindings/reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (94%)
--
2.11.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 62+ messages in thread
* [PATCH v5 0/7] Allwinner H5 and Orange Pi PC2 support
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: linux-arm-kernel
Allwinner H5 is a 64-bit SoC with a design like the 32-bit
H3.
This patchset adds support for it, along with the first available
board -- Orange Pi PC2.
Andre Przywara (3):
arm: dts: sun8i: split Allwinner H3 .dtsi
arm64: dts: allwinner: add Allwinner H5 .dtsi
arm64: dts: sunxi: add support for the Orange Pi PC 2 board
Icenowy Zheng (4):
arm64: allwinner: Kconfig: add essential pinctrl driver for H5
clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
clk: sunxi-ng: add support for Allwinner H5 SoC
ARM: dts: sun8i: convert H3 dtsi to use new sunxi-h3-h5 binding header
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
arch/arm/boot/dts/sun8i-h3.dtsi | 589 ++-------------------
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 575 ++++++++++++++++++++
arch/arm64/Kconfig.platforms | 5 +-
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 164 ++++++
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 139 +++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
drivers/clk/sunxi-ng/Kconfig | 6 +-
drivers/clk/sunxi-ng/Makefile | 2 +-
.../sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} | 339 +++++++++++-
.../sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} | 13 +-
.../clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 11 +-
.../reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 11 +-
14 files changed, 1277 insertions(+), 580 deletions(-)
create mode 100644 arch/arm/boot/dts/sunxi-h3-h5.dtsi
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} (71%)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} (83%)
rename include/dt-bindings/clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (95%)
rename include/dt-bindings/reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (94%)
--
2.11.1
^ permalink raw reply [flat|nested] 62+ messages in thread
* [PATCH v5 1/7] arm64: allwinner: Kconfig: add essential pinctrl driver for H5
2017-02-26 1:19 ` Icenowy Zheng
(?)
@ 2017-02-26 1:19 ` Icenowy Zheng
-1 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
H5 SoC has two pin controllers, one (in user manual called "CPUx") needs
a slightly advanced driver, and the other (called "CPUs") is just equal
to the on in H3, and the H3 driver can be just reused.
Select the two necessary pinctrl drivers when building kernel for
Allwinner SoCs.
Also add H5 in the option's description.
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
arch/arm64/Kconfig.platforms | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index 129cc5ae4091..81f0d6149c2e 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -5,8 +5,11 @@ config ARCH_SUNXI
select GENERIC_IRQ_CHIP
select PINCTRL
select PINCTRL_SUN50I_A64
+ select PINCTRL_SUN50I_H5
+ select PINCTRL_SUN8I_H3_R
help
- This enables support for Allwinner sunxi based SoCs like the A64.
+ This enables support for Allwinner sunxi based SoCs like the A64
+ and H5.
config ARCH_ALPINE
bool "Annapurna Labs Alpine platform"
--
2.11.1
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 1/7] arm64: allwinner: Kconfig: add essential pinctrl driver for H5
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara
Cc: devicetree, linux-kernel, linux-sunxi, Icenowy Zheng, linux-clk,
linux-arm-kernel
H5 SoC has two pin controllers, one (in user manual called "CPUx") needs
a slightly advanced driver, and the other (called "CPUs") is just equal
to the on in H3, and the H3 driver can be just reused.
Select the two necessary pinctrl drivers when building kernel for
Allwinner SoCs.
Also add H5 in the option's description.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
arch/arm64/Kconfig.platforms | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index 129cc5ae4091..81f0d6149c2e 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -5,8 +5,11 @@ config ARCH_SUNXI
select GENERIC_IRQ_CHIP
select PINCTRL
select PINCTRL_SUN50I_A64
+ select PINCTRL_SUN50I_H5
+ select PINCTRL_SUN8I_H3_R
help
- This enables support for Allwinner sunxi based SoCs like the A64.
+ This enables support for Allwinner sunxi based SoCs like the A64
+ and H5.
config ARCH_ALPINE
bool "Annapurna Labs Alpine platform"
--
2.11.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 1/7] arm64: allwinner: Kconfig: add essential pinctrl driver for H5
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: linux-arm-kernel
H5 SoC has two pin controllers, one (in user manual called "CPUx") needs
a slightly advanced driver, and the other (called "CPUs") is just equal
to the on in H3, and the H3 driver can be just reused.
Select the two necessary pinctrl drivers when building kernel for
Allwinner SoCs.
Also add H5 in the option's description.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
arch/arm64/Kconfig.platforms | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index 129cc5ae4091..81f0d6149c2e 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -5,8 +5,11 @@ config ARCH_SUNXI
select GENERIC_IRQ_CHIP
select PINCTRL
select PINCTRL_SUN50I_A64
+ select PINCTRL_SUN50I_H5
+ select PINCTRL_SUN8I_H3_R
help
- This enables support for Allwinner sunxi based SoCs like the A64.
+ This enables support for Allwinner sunxi based SoCs like the A64
+ and H5.
config ARCH_ALPINE
bool "Annapurna Labs Alpine platform"
--
2.11.1
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 2/7] clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
2017-02-26 1:19 ` Icenowy Zheng
(?)
@ 2017-02-26 1:19 ` Icenowy Zheng
-1 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
As the CCU in the Allwinner H5 SoC is very similar to the one in H3,
rename the H3 driver to sunxi-h3-h5 so that it can be extended with H5
support.
Trasitional header symlinks are created, to ensure current device tree
files which included sun8i-h3-ccu.h can compile.
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
Changes in v5:
- Add the reason to create trasitional headers in commit message.
Changes in v4:
- Fixed an indent issue.
drivers/clk/sunxi-ng/Kconfig | 4 +-
drivers/clk/sunxi-ng/Makefile | 2 +-
.../sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} | 42 +++---
.../sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} | 10 +-
include/dt-bindings/clock/sun8i-h3-ccu.h | 146 +--------------------
.../clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 8 +-
include/dt-bindings/reset/sun8i-h3-ccu.h | 104 +--------------
.../reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 8 +-
8 files changed, 42 insertions(+), 282 deletions(-)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} (96%)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} (88%)
rewrite include/dt-bindings/clock/sun8i-h3-ccu.h (100%)
mode change 100644 => 120000
copy include/dt-bindings/clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (96%)
rewrite include/dt-bindings/reset/sun8i-h3-ccu.h (100%)
mode change 100644 => 120000
copy include/dt-bindings/reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (95%)
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 695bbf9ef428..af6a5a5dd549 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -109,8 +109,8 @@ config SUN8I_A33_CCU
select SUNXI_CCU_PHASE
default MACH_SUN8I
-config SUN8I_H3_CCU
- bool "Support for the Allwinner H3 CCU"
+config SUNXI_H3_H5_CCU
+ bool "Support for the Allwinner H3/H5 CCU"
select SUNXI_CCU_DIV
select SUNXI_CCU_NK
select SUNXI_CCU_NKM
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 6feaac0c5600..22649859b5a9 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -23,7 +23,7 @@ obj-$(CONFIG_SUN5I_CCU) += ccu-sun5i.o
obj-$(CONFIG_SUN6I_A31_CCU) += ccu-sun6i-a31.o
obj-$(CONFIG_SUN8I_A23_CCU) += ccu-sun8i-a23.o
obj-$(CONFIG_SUN8I_A33_CCU) += ccu-sun8i-a33.o
-obj-$(CONFIG_SUN8I_H3_CCU) += ccu-sun8i-h3.o
+obj-$(CONFIG_SUNXI_H3_H5_CCU) += ccu-sunxi-h3-h5.o
obj-$(CONFIG_SUN8I_V3S_CCU) += ccu-sun8i-v3s.o
obj-$(CONFIG_SUN9I_A80_CCU) += ccu-sun9i-a80.o
obj-$(CONFIG_SUN9I_A80_CCU) += ccu-sun9i-a80-de.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
similarity index 96%
rename from drivers/clk/sunxi-ng/ccu-sun8i-h3.c
rename to drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
index a26c8a19fe93..e2d065973794 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
@@ -27,7 +27,7 @@
#include "ccu_nm.h"
#include "ccu_phase.h"
-#include "ccu-sun8i-h3.h"
+#include "ccu-sunxi-h3-h5.h"
static SUNXI_CCU_NKMP_WITH_GATE_LOCK(pll_cpux_clk, "pll-cpux",
"osc24M", 0x000,
@@ -47,7 +47,7 @@ static SUNXI_CCU_NKMP_WITH_GATE_LOCK(pll_cpux_clk, "pll-cpux",
* We don't have any need for the variable divider for now, so we just
* hardcode it to match with the clock names
*/
-#define SUN8I_H3_PLL_AUDIO_REG 0x008
+#define SUNXI_H3_H5_PLL_AUDIO_REG 0x008
static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_audio_base_clk, "pll-audio-base",
"osc24M", 0x008,
@@ -300,7 +300,7 @@ static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2",
0x06c, BIT(18), 0);
static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
0x06c, BIT(19), 0);
-static SUNXI_CCU_GATE(bus_scr_clk, "bus-scr", "apb2",
+static SUNXI_CCU_GATE(bus_scr0_clk, "bus-scr0", "apb2",
0x06c, BIT(20), 0);
static SUNXI_CCU_GATE(bus_ephy_clk, "bus-ephy", "ahb1",
@@ -484,7 +484,7 @@ static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents,
static SUNXI_CCU_M_WITH_GATE(gpu_clk, "gpu", "pll-gpu",
0x1a0, 0, 3, BIT(31), 0);
-static struct ccu_common *sun8i_h3_ccu_clks[] = {
+static struct ccu_common *sunxi_h3_h5_ccu_clks[] = {
&pll_cpux_clk.common,
&pll_audio_base_clk.common,
&pll_video_clk.common,
@@ -546,7 +546,7 @@ static struct ccu_common *sun8i_h3_ccu_clks[] = {
&bus_uart1_clk.common,
&bus_uart2_clk.common,
&bus_uart3_clk.common,
- &bus_scr_clk.common,
+ &bus_scr0_clk.common,
&bus_ephy_clk.common,
&bus_dbg_clk.common,
&ths_clk.common,
@@ -677,7 +677,7 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
[CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
[CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
[CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
- [CLK_BUS_SCR] = &bus_scr_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
[CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
[CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
[CLK_THS] = &ths_clk.common.hw,
@@ -730,7 +730,7 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
.num = CLK_NUMBER,
};
-static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
+static struct ccu_reset_map sunxi_h3_h5_ccu_resets[] = {
[RST_USB_PHY0] = { 0x0cc, BIT(0) },
[RST_USB_PHY1] = { 0x0cc, BIT(1) },
[RST_USB_PHY2] = { 0x0cc, BIT(2) },
@@ -790,27 +790,28 @@ static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
[RST_BUS_UART1] = { 0x2d8, BIT(17) },
[RST_BUS_UART2] = { 0x2d8, BIT(18) },
[RST_BUS_UART3] = { 0x2d8, BIT(19) },
- [RST_BUS_SCR] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR0] = { 0x2d8, BIT(20) },
};
static const struct sunxi_ccu_desc sun8i_h3_ccu_desc = {
- .ccu_clks = sun8i_h3_ccu_clks,
- .num_ccu_clks = ARRAY_SIZE(sun8i_h3_ccu_clks),
+ .ccu_clks = sunxi_h3_h5_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sunxi_h3_h5_ccu_clks),
.hw_clks = &sun8i_h3_hw_clks,
- .resets = sun8i_h3_ccu_resets,
- .num_resets = ARRAY_SIZE(sun8i_h3_ccu_resets),
+ .resets = sunxi_h3_h5_ccu_resets,
+ .num_resets = ARRAY_SIZE(sunxi_h3_h5_ccu_resets),
};
-static struct ccu_mux_nb sun8i_h3_cpu_nb = {
+static struct ccu_mux_nb sunxi_h3_h5_cpu_nb = {
.common = &cpux_clk.common,
.cm = &cpux_clk.mux,
.delay_us = 1, /* > 8 clock cycles at 24 MHz */
.bypass_index = 1, /* index of 24 MHz oscillator */
};
-static void __init sun8i_h3_ccu_setup(struct device_node *node)
+static void __init sunxi_h3_h5_ccu_init(struct device_node *node,
+ const struct sunxi_ccu_desc *desc)
{
void __iomem *reg;
u32 val;
@@ -823,14 +824,19 @@ static void __init sun8i_h3_ccu_setup(struct device_node *node)
}
/* Force the PLL-Audio-1x divider to 4 */
- val = readl(reg + SUN8I_H3_PLL_AUDIO_REG);
+ val = readl(reg + SUNXI_H3_H5_PLL_AUDIO_REG);
val &= ~GENMASK(19, 16);
- writel(val | (3 << 16), reg + SUN8I_H3_PLL_AUDIO_REG);
+ writel(val | (3 << 16), reg + SUNXI_H3_H5_PLL_AUDIO_REG);
- sunxi_ccu_probe(node, reg, &sun8i_h3_ccu_desc);
+ sunxi_ccu_probe(node, reg, desc);
ccu_mux_notifier_register(pll_cpux_clk.common.hw.clk,
- &sun8i_h3_cpu_nb);
+ &sunxi_h3_h5_cpu_nb);
+}
+
+static void __init sun8i_h3_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun8i_h3_ccu_desc);
}
CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
sun8i_h3_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
similarity index 88%
rename from drivers/clk/sunxi-ng/ccu-sun8i-h3.h
rename to drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
index 78be712c7487..e2a4656d2cf3 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
@@ -14,11 +14,11 @@
* GNU General Public License for more details.
*/
-#ifndef _CCU_SUN8I_H3_H_
-#define _CCU_SUN8I_H3_H_
+#ifndef _CCU_SUNXI_H3_H5_H_
+#define _CCU_SUNXI_H3_H5_H_
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
+#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
+#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
#define CLK_PLL_CPUX 0
#define CLK_PLL_AUDIO_BASE 1
@@ -59,4 +59,4 @@
#define CLK_NUMBER (CLK_GPU + 1)
-#endif /* _CCU_SUN8I_H3_H_ */
+#endif /* _CCU_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
deleted file mode 100644
index efb7ba2bd515..000000000000
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ /dev/null
@@ -1,145 +0,0 @@
-/*
- * Copyright (C) 2016 Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#ifndef _DT_BINDINGS_CLK_SUN8I_H3_H_
-#define _DT_BINDINGS_CLK_SUN8I_H3_H_
-
-#define CLK_CPUX 14
-
-#define CLK_BUS_CE 20
-#define CLK_BUS_DMA 21
-#define CLK_BUS_MMC0 22
-#define CLK_BUS_MMC1 23
-#define CLK_BUS_MMC2 24
-#define CLK_BUS_NAND 25
-#define CLK_BUS_DRAM 26
-#define CLK_BUS_EMAC 27
-#define CLK_BUS_TS 28
-#define CLK_BUS_HSTIMER 29
-#define CLK_BUS_SPI0 30
-#define CLK_BUS_SPI1 31
-#define CLK_BUS_OTG 32
-#define CLK_BUS_EHCI0 33
-#define CLK_BUS_EHCI1 34
-#define CLK_BUS_EHCI2 35
-#define CLK_BUS_EHCI3 36
-#define CLK_BUS_OHCI0 37
-#define CLK_BUS_OHCI1 38
-#define CLK_BUS_OHCI2 39
-#define CLK_BUS_OHCI3 40
-#define CLK_BUS_VE 41
-#define CLK_BUS_TCON0 42
-#define CLK_BUS_TCON1 43
-#define CLK_BUS_DEINTERLACE 44
-#define CLK_BUS_CSI 45
-#define CLK_BUS_TVE 46
-#define CLK_BUS_HDMI 47
-#define CLK_BUS_DE 48
-#define CLK_BUS_GPU 49
-#define CLK_BUS_MSGBOX 50
-#define CLK_BUS_SPINLOCK 51
-#define CLK_BUS_CODEC 52
-#define CLK_BUS_SPDIF 53
-#define CLK_BUS_PIO 54
-#define CLK_BUS_THS 55
-#define CLK_BUS_I2S0 56
-#define CLK_BUS_I2S1 57
-#define CLK_BUS_I2S2 58
-#define CLK_BUS_I2C0 59
-#define CLK_BUS_I2C1 60
-#define CLK_BUS_I2C2 61
-#define CLK_BUS_UART0 62
-#define CLK_BUS_UART1 63
-#define CLK_BUS_UART2 64
-#define CLK_BUS_UART3 65
-#define CLK_BUS_SCR 66
-#define CLK_BUS_EPHY 67
-#define CLK_BUS_DBG 68
-
-#define CLK_THS 69
-#define CLK_NAND 70
-#define CLK_MMC0 71
-#define CLK_MMC0_SAMPLE 72
-#define CLK_MMC0_OUTPUT 73
-#define CLK_MMC1 74
-#define CLK_MMC1_SAMPLE 75
-#define CLK_MMC1_OUTPUT 76
-#define CLK_MMC2 77
-#define CLK_MMC2_SAMPLE 78
-#define CLK_MMC2_OUTPUT 79
-#define CLK_TS 80
-#define CLK_CE 81
-#define CLK_SPI0 82
-#define CLK_SPI1 83
-#define CLK_I2S0 84
-#define CLK_I2S1 85
-#define CLK_I2S2 86
-#define CLK_SPDIF 87
-#define CLK_USB_PHY0 88
-#define CLK_USB_PHY1 89
-#define CLK_USB_PHY2 90
-#define CLK_USB_PHY3 91
-#define CLK_USB_OHCI0 92
-#define CLK_USB_OHCI1 93
-#define CLK_USB_OHCI2 94
-#define CLK_USB_OHCI3 95
-
-#define CLK_DRAM_VE 97
-#define CLK_DRAM_CSI 98
-#define CLK_DRAM_DEINTERLACE 99
-#define CLK_DRAM_TS 100
-#define CLK_DE 101
-#define CLK_TCON0 102
-#define CLK_TVE 103
-#define CLK_DEINTERLACE 104
-#define CLK_CSI_MISC 105
-#define CLK_CSI_SCLK 106
-#define CLK_CSI_MCLK 107
-#define CLK_VE 108
-#define CLK_AC_DIG 109
-#define CLK_AVS 110
-#define CLK_HDMI 111
-#define CLK_HDMI_DDC 112
-
-#define CLK_GPU 114
-
-#endif /* _DT_BINDINGS_CLK_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
new file mode 120000
index 000000000000..ef38232141e4
--- /dev/null
+++ b/include/dt-bindings/clock/sun8i-h3-ccu.h
@@ -0,0 +1 @@
+sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
similarity index 96%
copy from include/dt-bindings/clock/sun8i-h3-ccu.h
copy to include/dt-bindings/clock/sunxi-h3-h5-ccu.h
index efb7ba2bd515..1715a5e12525 100644
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
@@ -40,8 +40,8 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#ifndef _DT_BINDINGS_CLK_SUN8I_H3_H_
-#define _DT_BINDINGS_CLK_SUN8I_H3_H_
+#ifndef _DT_BINDINGS_CLK_SUNXI_H3_H5_H_
+#define _DT_BINDINGS_CLK_SUNXI_H3_H5_H_
#define CLK_CPUX 14
@@ -91,7 +91,7 @@
#define CLK_BUS_UART1 63
#define CLK_BUS_UART2 64
#define CLK_BUS_UART3 65
-#define CLK_BUS_SCR 66
+#define CLK_BUS_SCR0 66
#define CLK_BUS_EPHY 67
#define CLK_BUS_DBG 68
@@ -142,4 +142,4 @@
#define CLK_GPU 114
-#endif /* _DT_BINDINGS_CLK_SUN8I_H3_H_ */
+#endif /* _DT_BINDINGS_CLK_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
deleted file mode 100644
index 6b7af80c26ec..000000000000
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ /dev/null
@@ -1,103 +0,0 @@
-/*
- * Copyright (C) 2016 Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#ifndef _DT_BINDINGS_RST_SUN8I_H3_H_
-#define _DT_BINDINGS_RST_SUN8I_H3_H_
-
-#define RST_USB_PHY0 0
-#define RST_USB_PHY1 1
-#define RST_USB_PHY2 2
-#define RST_USB_PHY3 3
-
-#define RST_MBUS 4
-
-#define RST_BUS_CE 5
-#define RST_BUS_DMA 6
-#define RST_BUS_MMC0 7
-#define RST_BUS_MMC1 8
-#define RST_BUS_MMC2 9
-#define RST_BUS_NAND 10
-#define RST_BUS_DRAM 11
-#define RST_BUS_EMAC 12
-#define RST_BUS_TS 13
-#define RST_BUS_HSTIMER 14
-#define RST_BUS_SPI0 15
-#define RST_BUS_SPI1 16
-#define RST_BUS_OTG 17
-#define RST_BUS_EHCI0 18
-#define RST_BUS_EHCI1 19
-#define RST_BUS_EHCI2 20
-#define RST_BUS_EHCI3 21
-#define RST_BUS_OHCI0 22
-#define RST_BUS_OHCI1 23
-#define RST_BUS_OHCI2 24
-#define RST_BUS_OHCI3 25
-#define RST_BUS_VE 26
-#define RST_BUS_TCON0 27
-#define RST_BUS_TCON1 28
-#define RST_BUS_DEINTERLACE 29
-#define RST_BUS_CSI 30
-#define RST_BUS_TVE 31
-#define RST_BUS_HDMI0 32
-#define RST_BUS_HDMI1 33
-#define RST_BUS_DE 34
-#define RST_BUS_GPU 35
-#define RST_BUS_MSGBOX 36
-#define RST_BUS_SPINLOCK 37
-#define RST_BUS_DBG 38
-#define RST_BUS_EPHY 39
-#define RST_BUS_CODEC 40
-#define RST_BUS_SPDIF 41
-#define RST_BUS_THS 42
-#define RST_BUS_I2S0 43
-#define RST_BUS_I2S1 44
-#define RST_BUS_I2S2 45
-#define RST_BUS_I2C0 46
-#define RST_BUS_I2C1 47
-#define RST_BUS_I2C2 48
-#define RST_BUS_UART0 49
-#define RST_BUS_UART1 50
-#define RST_BUS_UART2 51
-#define RST_BUS_UART3 52
-#define RST_BUS_SCR 53
-
-#endif /* _DT_BINDINGS_RST_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
new file mode 120000
index 000000000000..ef38232141e4
--- /dev/null
+++ b/include/dt-bindings/reset/sun8i-h3-ccu.h
@@ -0,0 +1 @@
+sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
similarity index 95%
copy from include/dt-bindings/reset/sun8i-h3-ccu.h
copy to include/dt-bindings/reset/sunxi-h3-h5-ccu.h
index 6b7af80c26ec..7a5de896cf1f 100644
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
@@ -40,8 +40,8 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#ifndef _DT_BINDINGS_RST_SUN8I_H3_H_
-#define _DT_BINDINGS_RST_SUN8I_H3_H_
+#ifndef _DT_BINDINGS_RST_SUNXI_H3_H5_H_
+#define _DT_BINDINGS_RST_SUNXI_H3_H5_H_
#define RST_USB_PHY0 0
#define RST_USB_PHY1 1
@@ -98,6 +98,6 @@
#define RST_BUS_UART1 50
#define RST_BUS_UART2 51
#define RST_BUS_UART3 52
-#define RST_BUS_SCR 53
+#define RST_BUS_SCR0 53
-#endif /* _DT_BINDINGS_RST_SUN8I_H3_H_ */
+#endif /* _DT_BINDINGS_RST_SUNXI_H3_H5_H_ */
--
2.11.1
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 2/7] clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara
Cc: devicetree, linux-kernel, linux-sunxi, Icenowy Zheng, linux-clk,
linux-arm-kernel
As the CCU in the Allwinner H5 SoC is very similar to the one in H3,
rename the H3 driver to sunxi-h3-h5 so that it can be extended with H5
support.
Trasitional header symlinks are created, to ensure current device tree
files which included sun8i-h3-ccu.h can compile.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v5:
- Add the reason to create trasitional headers in commit message.
Changes in v4:
- Fixed an indent issue.
drivers/clk/sunxi-ng/Kconfig | 4 +-
drivers/clk/sunxi-ng/Makefile | 2 +-
.../sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} | 42 +++---
.../sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} | 10 +-
include/dt-bindings/clock/sun8i-h3-ccu.h | 146 +--------------------
.../clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 8 +-
include/dt-bindings/reset/sun8i-h3-ccu.h | 104 +--------------
.../reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 8 +-
8 files changed, 42 insertions(+), 282 deletions(-)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} (96%)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} (88%)
rewrite include/dt-bindings/clock/sun8i-h3-ccu.h (100%)
mode change 100644 => 120000
copy include/dt-bindings/clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (96%)
rewrite include/dt-bindings/reset/sun8i-h3-ccu.h (100%)
mode change 100644 => 120000
copy include/dt-bindings/reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (95%)
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 695bbf9ef428..af6a5a5dd549 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -109,8 +109,8 @@ config SUN8I_A33_CCU
select SUNXI_CCU_PHASE
default MACH_SUN8I
-config SUN8I_H3_CCU
- bool "Support for the Allwinner H3 CCU"
+config SUNXI_H3_H5_CCU
+ bool "Support for the Allwinner H3/H5 CCU"
select SUNXI_CCU_DIV
select SUNXI_CCU_NK
select SUNXI_CCU_NKM
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 6feaac0c5600..22649859b5a9 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -23,7 +23,7 @@ obj-$(CONFIG_SUN5I_CCU) += ccu-sun5i.o
obj-$(CONFIG_SUN6I_A31_CCU) += ccu-sun6i-a31.o
obj-$(CONFIG_SUN8I_A23_CCU) += ccu-sun8i-a23.o
obj-$(CONFIG_SUN8I_A33_CCU) += ccu-sun8i-a33.o
-obj-$(CONFIG_SUN8I_H3_CCU) += ccu-sun8i-h3.o
+obj-$(CONFIG_SUNXI_H3_H5_CCU) += ccu-sunxi-h3-h5.o
obj-$(CONFIG_SUN8I_V3S_CCU) += ccu-sun8i-v3s.o
obj-$(CONFIG_SUN9I_A80_CCU) += ccu-sun9i-a80.o
obj-$(CONFIG_SUN9I_A80_CCU) += ccu-sun9i-a80-de.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
similarity index 96%
rename from drivers/clk/sunxi-ng/ccu-sun8i-h3.c
rename to drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
index a26c8a19fe93..e2d065973794 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
@@ -27,7 +27,7 @@
#include "ccu_nm.h"
#include "ccu_phase.h"
-#include "ccu-sun8i-h3.h"
+#include "ccu-sunxi-h3-h5.h"
static SUNXI_CCU_NKMP_WITH_GATE_LOCK(pll_cpux_clk, "pll-cpux",
"osc24M", 0x000,
@@ -47,7 +47,7 @@ static SUNXI_CCU_NKMP_WITH_GATE_LOCK(pll_cpux_clk, "pll-cpux",
* We don't have any need for the variable divider for now, so we just
* hardcode it to match with the clock names
*/
-#define SUN8I_H3_PLL_AUDIO_REG 0x008
+#define SUNXI_H3_H5_PLL_AUDIO_REG 0x008
static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_audio_base_clk, "pll-audio-base",
"osc24M", 0x008,
@@ -300,7 +300,7 @@ static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2",
0x06c, BIT(18), 0);
static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
0x06c, BIT(19), 0);
-static SUNXI_CCU_GATE(bus_scr_clk, "bus-scr", "apb2",
+static SUNXI_CCU_GATE(bus_scr0_clk, "bus-scr0", "apb2",
0x06c, BIT(20), 0);
static SUNXI_CCU_GATE(bus_ephy_clk, "bus-ephy", "ahb1",
@@ -484,7 +484,7 @@ static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents,
static SUNXI_CCU_M_WITH_GATE(gpu_clk, "gpu", "pll-gpu",
0x1a0, 0, 3, BIT(31), 0);
-static struct ccu_common *sun8i_h3_ccu_clks[] = {
+static struct ccu_common *sunxi_h3_h5_ccu_clks[] = {
&pll_cpux_clk.common,
&pll_audio_base_clk.common,
&pll_video_clk.common,
@@ -546,7 +546,7 @@ static struct ccu_common *sun8i_h3_ccu_clks[] = {
&bus_uart1_clk.common,
&bus_uart2_clk.common,
&bus_uart3_clk.common,
- &bus_scr_clk.common,
+ &bus_scr0_clk.common,
&bus_ephy_clk.common,
&bus_dbg_clk.common,
&ths_clk.common,
@@ -677,7 +677,7 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
[CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
[CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
[CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
- [CLK_BUS_SCR] = &bus_scr_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
[CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
[CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
[CLK_THS] = &ths_clk.common.hw,
@@ -730,7 +730,7 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
.num = CLK_NUMBER,
};
-static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
+static struct ccu_reset_map sunxi_h3_h5_ccu_resets[] = {
[RST_USB_PHY0] = { 0x0cc, BIT(0) },
[RST_USB_PHY1] = { 0x0cc, BIT(1) },
[RST_USB_PHY2] = { 0x0cc, BIT(2) },
@@ -790,27 +790,28 @@ static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
[RST_BUS_UART1] = { 0x2d8, BIT(17) },
[RST_BUS_UART2] = { 0x2d8, BIT(18) },
[RST_BUS_UART3] = { 0x2d8, BIT(19) },
- [RST_BUS_SCR] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR0] = { 0x2d8, BIT(20) },
};
static const struct sunxi_ccu_desc sun8i_h3_ccu_desc = {
- .ccu_clks = sun8i_h3_ccu_clks,
- .num_ccu_clks = ARRAY_SIZE(sun8i_h3_ccu_clks),
+ .ccu_clks = sunxi_h3_h5_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sunxi_h3_h5_ccu_clks),
.hw_clks = &sun8i_h3_hw_clks,
- .resets = sun8i_h3_ccu_resets,
- .num_resets = ARRAY_SIZE(sun8i_h3_ccu_resets),
+ .resets = sunxi_h3_h5_ccu_resets,
+ .num_resets = ARRAY_SIZE(sunxi_h3_h5_ccu_resets),
};
-static struct ccu_mux_nb sun8i_h3_cpu_nb = {
+static struct ccu_mux_nb sunxi_h3_h5_cpu_nb = {
.common = &cpux_clk.common,
.cm = &cpux_clk.mux,
.delay_us = 1, /* > 8 clock cycles at 24 MHz */
.bypass_index = 1, /* index of 24 MHz oscillator */
};
-static void __init sun8i_h3_ccu_setup(struct device_node *node)
+static void __init sunxi_h3_h5_ccu_init(struct device_node *node,
+ const struct sunxi_ccu_desc *desc)
{
void __iomem *reg;
u32 val;
@@ -823,14 +824,19 @@ static void __init sun8i_h3_ccu_setup(struct device_node *node)
}
/* Force the PLL-Audio-1x divider to 4 */
- val = readl(reg + SUN8I_H3_PLL_AUDIO_REG);
+ val = readl(reg + SUNXI_H3_H5_PLL_AUDIO_REG);
val &= ~GENMASK(19, 16);
- writel(val | (3 << 16), reg + SUN8I_H3_PLL_AUDIO_REG);
+ writel(val | (3 << 16), reg + SUNXI_H3_H5_PLL_AUDIO_REG);
- sunxi_ccu_probe(node, reg, &sun8i_h3_ccu_desc);
+ sunxi_ccu_probe(node, reg, desc);
ccu_mux_notifier_register(pll_cpux_clk.common.hw.clk,
- &sun8i_h3_cpu_nb);
+ &sunxi_h3_h5_cpu_nb);
+}
+
+static void __init sun8i_h3_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun8i_h3_ccu_desc);
}
CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
sun8i_h3_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
similarity index 88%
rename from drivers/clk/sunxi-ng/ccu-sun8i-h3.h
rename to drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
index 78be712c7487..e2a4656d2cf3 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
@@ -14,11 +14,11 @@
* GNU General Public License for more details.
*/
-#ifndef _CCU_SUN8I_H3_H_
-#define _CCU_SUN8I_H3_H_
+#ifndef _CCU_SUNXI_H3_H5_H_
+#define _CCU_SUNXI_H3_H5_H_
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
+#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
+#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
#define CLK_PLL_CPUX 0
#define CLK_PLL_AUDIO_BASE 1
@@ -59,4 +59,4 @@
#define CLK_NUMBER (CLK_GPU + 1)
-#endif /* _CCU_SUN8I_H3_H_ */
+#endif /* _CCU_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
deleted file mode 100644
index efb7ba2bd515..000000000000
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ /dev/null
@@ -1,145 +0,0 @@
-/*
- * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#ifndef _DT_BINDINGS_CLK_SUN8I_H3_H_
-#define _DT_BINDINGS_CLK_SUN8I_H3_H_
-
-#define CLK_CPUX 14
-
-#define CLK_BUS_CE 20
-#define CLK_BUS_DMA 21
-#define CLK_BUS_MMC0 22
-#define CLK_BUS_MMC1 23
-#define CLK_BUS_MMC2 24
-#define CLK_BUS_NAND 25
-#define CLK_BUS_DRAM 26
-#define CLK_BUS_EMAC 27
-#define CLK_BUS_TS 28
-#define CLK_BUS_HSTIMER 29
-#define CLK_BUS_SPI0 30
-#define CLK_BUS_SPI1 31
-#define CLK_BUS_OTG 32
-#define CLK_BUS_EHCI0 33
-#define CLK_BUS_EHCI1 34
-#define CLK_BUS_EHCI2 35
-#define CLK_BUS_EHCI3 36
-#define CLK_BUS_OHCI0 37
-#define CLK_BUS_OHCI1 38
-#define CLK_BUS_OHCI2 39
-#define CLK_BUS_OHCI3 40
-#define CLK_BUS_VE 41
-#define CLK_BUS_TCON0 42
-#define CLK_BUS_TCON1 43
-#define CLK_BUS_DEINTERLACE 44
-#define CLK_BUS_CSI 45
-#define CLK_BUS_TVE 46
-#define CLK_BUS_HDMI 47
-#define CLK_BUS_DE 48
-#define CLK_BUS_GPU 49
-#define CLK_BUS_MSGBOX 50
-#define CLK_BUS_SPINLOCK 51
-#define CLK_BUS_CODEC 52
-#define CLK_BUS_SPDIF 53
-#define CLK_BUS_PIO 54
-#define CLK_BUS_THS 55
-#define CLK_BUS_I2S0 56
-#define CLK_BUS_I2S1 57
-#define CLK_BUS_I2S2 58
-#define CLK_BUS_I2C0 59
-#define CLK_BUS_I2C1 60
-#define CLK_BUS_I2C2 61
-#define CLK_BUS_UART0 62
-#define CLK_BUS_UART1 63
-#define CLK_BUS_UART2 64
-#define CLK_BUS_UART3 65
-#define CLK_BUS_SCR 66
-#define CLK_BUS_EPHY 67
-#define CLK_BUS_DBG 68
-
-#define CLK_THS 69
-#define CLK_NAND 70
-#define CLK_MMC0 71
-#define CLK_MMC0_SAMPLE 72
-#define CLK_MMC0_OUTPUT 73
-#define CLK_MMC1 74
-#define CLK_MMC1_SAMPLE 75
-#define CLK_MMC1_OUTPUT 76
-#define CLK_MMC2 77
-#define CLK_MMC2_SAMPLE 78
-#define CLK_MMC2_OUTPUT 79
-#define CLK_TS 80
-#define CLK_CE 81
-#define CLK_SPI0 82
-#define CLK_SPI1 83
-#define CLK_I2S0 84
-#define CLK_I2S1 85
-#define CLK_I2S2 86
-#define CLK_SPDIF 87
-#define CLK_USB_PHY0 88
-#define CLK_USB_PHY1 89
-#define CLK_USB_PHY2 90
-#define CLK_USB_PHY3 91
-#define CLK_USB_OHCI0 92
-#define CLK_USB_OHCI1 93
-#define CLK_USB_OHCI2 94
-#define CLK_USB_OHCI3 95
-
-#define CLK_DRAM_VE 97
-#define CLK_DRAM_CSI 98
-#define CLK_DRAM_DEINTERLACE 99
-#define CLK_DRAM_TS 100
-#define CLK_DE 101
-#define CLK_TCON0 102
-#define CLK_TVE 103
-#define CLK_DEINTERLACE 104
-#define CLK_CSI_MISC 105
-#define CLK_CSI_SCLK 106
-#define CLK_CSI_MCLK 107
-#define CLK_VE 108
-#define CLK_AC_DIG 109
-#define CLK_AVS 110
-#define CLK_HDMI 111
-#define CLK_HDMI_DDC 112
-
-#define CLK_GPU 114
-
-#endif /* _DT_BINDINGS_CLK_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
new file mode 120000
index 000000000000..ef38232141e4
--- /dev/null
+++ b/include/dt-bindings/clock/sun8i-h3-ccu.h
@@ -0,0 +1 @@
+sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
similarity index 96%
copy from include/dt-bindings/clock/sun8i-h3-ccu.h
copy to include/dt-bindings/clock/sunxi-h3-h5-ccu.h
index efb7ba2bd515..1715a5e12525 100644
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
@@ -40,8 +40,8 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#ifndef _DT_BINDINGS_CLK_SUN8I_H3_H_
-#define _DT_BINDINGS_CLK_SUN8I_H3_H_
+#ifndef _DT_BINDINGS_CLK_SUNXI_H3_H5_H_
+#define _DT_BINDINGS_CLK_SUNXI_H3_H5_H_
#define CLK_CPUX 14
@@ -91,7 +91,7 @@
#define CLK_BUS_UART1 63
#define CLK_BUS_UART2 64
#define CLK_BUS_UART3 65
-#define CLK_BUS_SCR 66
+#define CLK_BUS_SCR0 66
#define CLK_BUS_EPHY 67
#define CLK_BUS_DBG 68
@@ -142,4 +142,4 @@
#define CLK_GPU 114
-#endif /* _DT_BINDINGS_CLK_SUN8I_H3_H_ */
+#endif /* _DT_BINDINGS_CLK_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
deleted file mode 100644
index 6b7af80c26ec..000000000000
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ /dev/null
@@ -1,103 +0,0 @@
-/*
- * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#ifndef _DT_BINDINGS_RST_SUN8I_H3_H_
-#define _DT_BINDINGS_RST_SUN8I_H3_H_
-
-#define RST_USB_PHY0 0
-#define RST_USB_PHY1 1
-#define RST_USB_PHY2 2
-#define RST_USB_PHY3 3
-
-#define RST_MBUS 4
-
-#define RST_BUS_CE 5
-#define RST_BUS_DMA 6
-#define RST_BUS_MMC0 7
-#define RST_BUS_MMC1 8
-#define RST_BUS_MMC2 9
-#define RST_BUS_NAND 10
-#define RST_BUS_DRAM 11
-#define RST_BUS_EMAC 12
-#define RST_BUS_TS 13
-#define RST_BUS_HSTIMER 14
-#define RST_BUS_SPI0 15
-#define RST_BUS_SPI1 16
-#define RST_BUS_OTG 17
-#define RST_BUS_EHCI0 18
-#define RST_BUS_EHCI1 19
-#define RST_BUS_EHCI2 20
-#define RST_BUS_EHCI3 21
-#define RST_BUS_OHCI0 22
-#define RST_BUS_OHCI1 23
-#define RST_BUS_OHCI2 24
-#define RST_BUS_OHCI3 25
-#define RST_BUS_VE 26
-#define RST_BUS_TCON0 27
-#define RST_BUS_TCON1 28
-#define RST_BUS_DEINTERLACE 29
-#define RST_BUS_CSI 30
-#define RST_BUS_TVE 31
-#define RST_BUS_HDMI0 32
-#define RST_BUS_HDMI1 33
-#define RST_BUS_DE 34
-#define RST_BUS_GPU 35
-#define RST_BUS_MSGBOX 36
-#define RST_BUS_SPINLOCK 37
-#define RST_BUS_DBG 38
-#define RST_BUS_EPHY 39
-#define RST_BUS_CODEC 40
-#define RST_BUS_SPDIF 41
-#define RST_BUS_THS 42
-#define RST_BUS_I2S0 43
-#define RST_BUS_I2S1 44
-#define RST_BUS_I2S2 45
-#define RST_BUS_I2C0 46
-#define RST_BUS_I2C1 47
-#define RST_BUS_I2C2 48
-#define RST_BUS_UART0 49
-#define RST_BUS_UART1 50
-#define RST_BUS_UART2 51
-#define RST_BUS_UART3 52
-#define RST_BUS_SCR 53
-
-#endif /* _DT_BINDINGS_RST_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
new file mode 120000
index 000000000000..ef38232141e4
--- /dev/null
+++ b/include/dt-bindings/reset/sun8i-h3-ccu.h
@@ -0,0 +1 @@
+sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
similarity index 95%
copy from include/dt-bindings/reset/sun8i-h3-ccu.h
copy to include/dt-bindings/reset/sunxi-h3-h5-ccu.h
index 6b7af80c26ec..7a5de896cf1f 100644
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
@@ -40,8 +40,8 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#ifndef _DT_BINDINGS_RST_SUN8I_H3_H_
-#define _DT_BINDINGS_RST_SUN8I_H3_H_
+#ifndef _DT_BINDINGS_RST_SUNXI_H3_H5_H_
+#define _DT_BINDINGS_RST_SUNXI_H3_H5_H_
#define RST_USB_PHY0 0
#define RST_USB_PHY1 1
@@ -98,6 +98,6 @@
#define RST_BUS_UART1 50
#define RST_BUS_UART2 51
#define RST_BUS_UART3 52
-#define RST_BUS_SCR 53
+#define RST_BUS_SCR0 53
-#endif /* _DT_BINDINGS_RST_SUN8I_H3_H_ */
+#endif /* _DT_BINDINGS_RST_SUNXI_H3_H5_H_ */
--
2.11.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 2/7] clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: linux-arm-kernel
As the CCU in the Allwinner H5 SoC is very similar to the one in H3,
rename the H3 driver to sunxi-h3-h5 so that it can be extended with H5
support.
Trasitional header symlinks are created, to ensure current device tree
files which included sun8i-h3-ccu.h can compile.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v5:
- Add the reason to create trasitional headers in commit message.
Changes in v4:
- Fixed an indent issue.
drivers/clk/sunxi-ng/Kconfig | 4 +-
drivers/clk/sunxi-ng/Makefile | 2 +-
.../sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} | 42 +++---
.../sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} | 10 +-
include/dt-bindings/clock/sun8i-h3-ccu.h | 146 +--------------------
.../clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 8 +-
include/dt-bindings/reset/sun8i-h3-ccu.h | 104 +--------------
.../reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 8 +-
8 files changed, 42 insertions(+), 282 deletions(-)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} (96%)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} (88%)
rewrite include/dt-bindings/clock/sun8i-h3-ccu.h (100%)
mode change 100644 => 120000
copy include/dt-bindings/clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (96%)
rewrite include/dt-bindings/reset/sun8i-h3-ccu.h (100%)
mode change 100644 => 120000
copy include/dt-bindings/reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (95%)
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 695bbf9ef428..af6a5a5dd549 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -109,8 +109,8 @@ config SUN8I_A33_CCU
select SUNXI_CCU_PHASE
default MACH_SUN8I
-config SUN8I_H3_CCU
- bool "Support for the Allwinner H3 CCU"
+config SUNXI_H3_H5_CCU
+ bool "Support for the Allwinner H3/H5 CCU"
select SUNXI_CCU_DIV
select SUNXI_CCU_NK
select SUNXI_CCU_NKM
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 6feaac0c5600..22649859b5a9 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -23,7 +23,7 @@ obj-$(CONFIG_SUN5I_CCU) += ccu-sun5i.o
obj-$(CONFIG_SUN6I_A31_CCU) += ccu-sun6i-a31.o
obj-$(CONFIG_SUN8I_A23_CCU) += ccu-sun8i-a23.o
obj-$(CONFIG_SUN8I_A33_CCU) += ccu-sun8i-a33.o
-obj-$(CONFIG_SUN8I_H3_CCU) += ccu-sun8i-h3.o
+obj-$(CONFIG_SUNXI_H3_H5_CCU) += ccu-sunxi-h3-h5.o
obj-$(CONFIG_SUN8I_V3S_CCU) += ccu-sun8i-v3s.o
obj-$(CONFIG_SUN9I_A80_CCU) += ccu-sun9i-a80.o
obj-$(CONFIG_SUN9I_A80_CCU) += ccu-sun9i-a80-de.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
similarity index 96%
rename from drivers/clk/sunxi-ng/ccu-sun8i-h3.c
rename to drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
index a26c8a19fe93..e2d065973794 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
@@ -27,7 +27,7 @@
#include "ccu_nm.h"
#include "ccu_phase.h"
-#include "ccu-sun8i-h3.h"
+#include "ccu-sunxi-h3-h5.h"
static SUNXI_CCU_NKMP_WITH_GATE_LOCK(pll_cpux_clk, "pll-cpux",
"osc24M", 0x000,
@@ -47,7 +47,7 @@ static SUNXI_CCU_NKMP_WITH_GATE_LOCK(pll_cpux_clk, "pll-cpux",
* We don't have any need for the variable divider for now, so we just
* hardcode it to match with the clock names
*/
-#define SUN8I_H3_PLL_AUDIO_REG 0x008
+#define SUNXI_H3_H5_PLL_AUDIO_REG 0x008
static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_audio_base_clk, "pll-audio-base",
"osc24M", 0x008,
@@ -300,7 +300,7 @@ static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2",
0x06c, BIT(18), 0);
static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
0x06c, BIT(19), 0);
-static SUNXI_CCU_GATE(bus_scr_clk, "bus-scr", "apb2",
+static SUNXI_CCU_GATE(bus_scr0_clk, "bus-scr0", "apb2",
0x06c, BIT(20), 0);
static SUNXI_CCU_GATE(bus_ephy_clk, "bus-ephy", "ahb1",
@@ -484,7 +484,7 @@ static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents,
static SUNXI_CCU_M_WITH_GATE(gpu_clk, "gpu", "pll-gpu",
0x1a0, 0, 3, BIT(31), 0);
-static struct ccu_common *sun8i_h3_ccu_clks[] = {
+static struct ccu_common *sunxi_h3_h5_ccu_clks[] = {
&pll_cpux_clk.common,
&pll_audio_base_clk.common,
&pll_video_clk.common,
@@ -546,7 +546,7 @@ static struct ccu_common *sun8i_h3_ccu_clks[] = {
&bus_uart1_clk.common,
&bus_uart2_clk.common,
&bus_uart3_clk.common,
- &bus_scr_clk.common,
+ &bus_scr0_clk.common,
&bus_ephy_clk.common,
&bus_dbg_clk.common,
&ths_clk.common,
@@ -677,7 +677,7 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
[CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
[CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
[CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
- [CLK_BUS_SCR] = &bus_scr_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
[CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
[CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
[CLK_THS] = &ths_clk.common.hw,
@@ -730,7 +730,7 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
.num = CLK_NUMBER,
};
-static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
+static struct ccu_reset_map sunxi_h3_h5_ccu_resets[] = {
[RST_USB_PHY0] = { 0x0cc, BIT(0) },
[RST_USB_PHY1] = { 0x0cc, BIT(1) },
[RST_USB_PHY2] = { 0x0cc, BIT(2) },
@@ -790,27 +790,28 @@ static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
[RST_BUS_UART1] = { 0x2d8, BIT(17) },
[RST_BUS_UART2] = { 0x2d8, BIT(18) },
[RST_BUS_UART3] = { 0x2d8, BIT(19) },
- [RST_BUS_SCR] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR0] = { 0x2d8, BIT(20) },
};
static const struct sunxi_ccu_desc sun8i_h3_ccu_desc = {
- .ccu_clks = sun8i_h3_ccu_clks,
- .num_ccu_clks = ARRAY_SIZE(sun8i_h3_ccu_clks),
+ .ccu_clks = sunxi_h3_h5_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sunxi_h3_h5_ccu_clks),
.hw_clks = &sun8i_h3_hw_clks,
- .resets = sun8i_h3_ccu_resets,
- .num_resets = ARRAY_SIZE(sun8i_h3_ccu_resets),
+ .resets = sunxi_h3_h5_ccu_resets,
+ .num_resets = ARRAY_SIZE(sunxi_h3_h5_ccu_resets),
};
-static struct ccu_mux_nb sun8i_h3_cpu_nb = {
+static struct ccu_mux_nb sunxi_h3_h5_cpu_nb = {
.common = &cpux_clk.common,
.cm = &cpux_clk.mux,
.delay_us = 1, /* > 8 clock cycles at 24 MHz */
.bypass_index = 1, /* index of 24 MHz oscillator */
};
-static void __init sun8i_h3_ccu_setup(struct device_node *node)
+static void __init sunxi_h3_h5_ccu_init(struct device_node *node,
+ const struct sunxi_ccu_desc *desc)
{
void __iomem *reg;
u32 val;
@@ -823,14 +824,19 @@ static void __init sun8i_h3_ccu_setup(struct device_node *node)
}
/* Force the PLL-Audio-1x divider to 4 */
- val = readl(reg + SUN8I_H3_PLL_AUDIO_REG);
+ val = readl(reg + SUNXI_H3_H5_PLL_AUDIO_REG);
val &= ~GENMASK(19, 16);
- writel(val | (3 << 16), reg + SUN8I_H3_PLL_AUDIO_REG);
+ writel(val | (3 << 16), reg + SUNXI_H3_H5_PLL_AUDIO_REG);
- sunxi_ccu_probe(node, reg, &sun8i_h3_ccu_desc);
+ sunxi_ccu_probe(node, reg, desc);
ccu_mux_notifier_register(pll_cpux_clk.common.hw.clk,
- &sun8i_h3_cpu_nb);
+ &sunxi_h3_h5_cpu_nb);
+}
+
+static void __init sun8i_h3_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun8i_h3_ccu_desc);
}
CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
sun8i_h3_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
similarity index 88%
rename from drivers/clk/sunxi-ng/ccu-sun8i-h3.h
rename to drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
index 78be712c7487..e2a4656d2cf3 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
@@ -14,11 +14,11 @@
* GNU General Public License for more details.
*/
-#ifndef _CCU_SUN8I_H3_H_
-#define _CCU_SUN8I_H3_H_
+#ifndef _CCU_SUNXI_H3_H5_H_
+#define _CCU_SUNXI_H3_H5_H_
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
+#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
+#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
#define CLK_PLL_CPUX 0
#define CLK_PLL_AUDIO_BASE 1
@@ -59,4 +59,4 @@
#define CLK_NUMBER (CLK_GPU + 1)
-#endif /* _CCU_SUN8I_H3_H_ */
+#endif /* _CCU_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
deleted file mode 100644
index efb7ba2bd515..000000000000
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ /dev/null
@@ -1,145 +0,0 @@
-/*
- * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#ifndef _DT_BINDINGS_CLK_SUN8I_H3_H_
-#define _DT_BINDINGS_CLK_SUN8I_H3_H_
-
-#define CLK_CPUX 14
-
-#define CLK_BUS_CE 20
-#define CLK_BUS_DMA 21
-#define CLK_BUS_MMC0 22
-#define CLK_BUS_MMC1 23
-#define CLK_BUS_MMC2 24
-#define CLK_BUS_NAND 25
-#define CLK_BUS_DRAM 26
-#define CLK_BUS_EMAC 27
-#define CLK_BUS_TS 28
-#define CLK_BUS_HSTIMER 29
-#define CLK_BUS_SPI0 30
-#define CLK_BUS_SPI1 31
-#define CLK_BUS_OTG 32
-#define CLK_BUS_EHCI0 33
-#define CLK_BUS_EHCI1 34
-#define CLK_BUS_EHCI2 35
-#define CLK_BUS_EHCI3 36
-#define CLK_BUS_OHCI0 37
-#define CLK_BUS_OHCI1 38
-#define CLK_BUS_OHCI2 39
-#define CLK_BUS_OHCI3 40
-#define CLK_BUS_VE 41
-#define CLK_BUS_TCON0 42
-#define CLK_BUS_TCON1 43
-#define CLK_BUS_DEINTERLACE 44
-#define CLK_BUS_CSI 45
-#define CLK_BUS_TVE 46
-#define CLK_BUS_HDMI 47
-#define CLK_BUS_DE 48
-#define CLK_BUS_GPU 49
-#define CLK_BUS_MSGBOX 50
-#define CLK_BUS_SPINLOCK 51
-#define CLK_BUS_CODEC 52
-#define CLK_BUS_SPDIF 53
-#define CLK_BUS_PIO 54
-#define CLK_BUS_THS 55
-#define CLK_BUS_I2S0 56
-#define CLK_BUS_I2S1 57
-#define CLK_BUS_I2S2 58
-#define CLK_BUS_I2C0 59
-#define CLK_BUS_I2C1 60
-#define CLK_BUS_I2C2 61
-#define CLK_BUS_UART0 62
-#define CLK_BUS_UART1 63
-#define CLK_BUS_UART2 64
-#define CLK_BUS_UART3 65
-#define CLK_BUS_SCR 66
-#define CLK_BUS_EPHY 67
-#define CLK_BUS_DBG 68
-
-#define CLK_THS 69
-#define CLK_NAND 70
-#define CLK_MMC0 71
-#define CLK_MMC0_SAMPLE 72
-#define CLK_MMC0_OUTPUT 73
-#define CLK_MMC1 74
-#define CLK_MMC1_SAMPLE 75
-#define CLK_MMC1_OUTPUT 76
-#define CLK_MMC2 77
-#define CLK_MMC2_SAMPLE 78
-#define CLK_MMC2_OUTPUT 79
-#define CLK_TS 80
-#define CLK_CE 81
-#define CLK_SPI0 82
-#define CLK_SPI1 83
-#define CLK_I2S0 84
-#define CLK_I2S1 85
-#define CLK_I2S2 86
-#define CLK_SPDIF 87
-#define CLK_USB_PHY0 88
-#define CLK_USB_PHY1 89
-#define CLK_USB_PHY2 90
-#define CLK_USB_PHY3 91
-#define CLK_USB_OHCI0 92
-#define CLK_USB_OHCI1 93
-#define CLK_USB_OHCI2 94
-#define CLK_USB_OHCI3 95
-
-#define CLK_DRAM_VE 97
-#define CLK_DRAM_CSI 98
-#define CLK_DRAM_DEINTERLACE 99
-#define CLK_DRAM_TS 100
-#define CLK_DE 101
-#define CLK_TCON0 102
-#define CLK_TVE 103
-#define CLK_DEINTERLACE 104
-#define CLK_CSI_MISC 105
-#define CLK_CSI_SCLK 106
-#define CLK_CSI_MCLK 107
-#define CLK_VE 108
-#define CLK_AC_DIG 109
-#define CLK_AVS 110
-#define CLK_HDMI 111
-#define CLK_HDMI_DDC 112
-
-#define CLK_GPU 114
-
-#endif /* _DT_BINDINGS_CLK_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
new file mode 120000
index 000000000000..ef38232141e4
--- /dev/null
+++ b/include/dt-bindings/clock/sun8i-h3-ccu.h
@@ -0,0 +1 @@
+sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
similarity index 96%
copy from include/dt-bindings/clock/sun8i-h3-ccu.h
copy to include/dt-bindings/clock/sunxi-h3-h5-ccu.h
index efb7ba2bd515..1715a5e12525 100644
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
@@ -40,8 +40,8 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#ifndef _DT_BINDINGS_CLK_SUN8I_H3_H_
-#define _DT_BINDINGS_CLK_SUN8I_H3_H_
+#ifndef _DT_BINDINGS_CLK_SUNXI_H3_H5_H_
+#define _DT_BINDINGS_CLK_SUNXI_H3_H5_H_
#define CLK_CPUX 14
@@ -91,7 +91,7 @@
#define CLK_BUS_UART1 63
#define CLK_BUS_UART2 64
#define CLK_BUS_UART3 65
-#define CLK_BUS_SCR 66
+#define CLK_BUS_SCR0 66
#define CLK_BUS_EPHY 67
#define CLK_BUS_DBG 68
@@ -142,4 +142,4 @@
#define CLK_GPU 114
-#endif /* _DT_BINDINGS_CLK_SUN8I_H3_H_ */
+#endif /* _DT_BINDINGS_CLK_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
deleted file mode 100644
index 6b7af80c26ec..000000000000
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ /dev/null
@@ -1,103 +0,0 @@
-/*
- * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#ifndef _DT_BINDINGS_RST_SUN8I_H3_H_
-#define _DT_BINDINGS_RST_SUN8I_H3_H_
-
-#define RST_USB_PHY0 0
-#define RST_USB_PHY1 1
-#define RST_USB_PHY2 2
-#define RST_USB_PHY3 3
-
-#define RST_MBUS 4
-
-#define RST_BUS_CE 5
-#define RST_BUS_DMA 6
-#define RST_BUS_MMC0 7
-#define RST_BUS_MMC1 8
-#define RST_BUS_MMC2 9
-#define RST_BUS_NAND 10
-#define RST_BUS_DRAM 11
-#define RST_BUS_EMAC 12
-#define RST_BUS_TS 13
-#define RST_BUS_HSTIMER 14
-#define RST_BUS_SPI0 15
-#define RST_BUS_SPI1 16
-#define RST_BUS_OTG 17
-#define RST_BUS_EHCI0 18
-#define RST_BUS_EHCI1 19
-#define RST_BUS_EHCI2 20
-#define RST_BUS_EHCI3 21
-#define RST_BUS_OHCI0 22
-#define RST_BUS_OHCI1 23
-#define RST_BUS_OHCI2 24
-#define RST_BUS_OHCI3 25
-#define RST_BUS_VE 26
-#define RST_BUS_TCON0 27
-#define RST_BUS_TCON1 28
-#define RST_BUS_DEINTERLACE 29
-#define RST_BUS_CSI 30
-#define RST_BUS_TVE 31
-#define RST_BUS_HDMI0 32
-#define RST_BUS_HDMI1 33
-#define RST_BUS_DE 34
-#define RST_BUS_GPU 35
-#define RST_BUS_MSGBOX 36
-#define RST_BUS_SPINLOCK 37
-#define RST_BUS_DBG 38
-#define RST_BUS_EPHY 39
-#define RST_BUS_CODEC 40
-#define RST_BUS_SPDIF 41
-#define RST_BUS_THS 42
-#define RST_BUS_I2S0 43
-#define RST_BUS_I2S1 44
-#define RST_BUS_I2S2 45
-#define RST_BUS_I2C0 46
-#define RST_BUS_I2C1 47
-#define RST_BUS_I2C2 48
-#define RST_BUS_UART0 49
-#define RST_BUS_UART1 50
-#define RST_BUS_UART2 51
-#define RST_BUS_UART3 52
-#define RST_BUS_SCR 53
-
-#endif /* _DT_BINDINGS_RST_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
new file mode 120000
index 000000000000..ef38232141e4
--- /dev/null
+++ b/include/dt-bindings/reset/sun8i-h3-ccu.h
@@ -0,0 +1 @@
+sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
similarity index 95%
copy from include/dt-bindings/reset/sun8i-h3-ccu.h
copy to include/dt-bindings/reset/sunxi-h3-h5-ccu.h
index 6b7af80c26ec..7a5de896cf1f 100644
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
@@ -40,8 +40,8 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#ifndef _DT_BINDINGS_RST_SUN8I_H3_H_
-#define _DT_BINDINGS_RST_SUN8I_H3_H_
+#ifndef _DT_BINDINGS_RST_SUNXI_H3_H5_H_
+#define _DT_BINDINGS_RST_SUNXI_H3_H5_H_
#define RST_USB_PHY0 0
#define RST_USB_PHY1 1
@@ -98,6 +98,6 @@
#define RST_BUS_UART1 50
#define RST_BUS_UART2 51
#define RST_BUS_UART3 52
-#define RST_BUS_SCR 53
+#define RST_BUS_SCR0 53
-#endif /* _DT_BINDINGS_RST_SUN8I_H3_H_ */
+#endif /* _DT_BINDINGS_RST_SUNXI_H3_H5_H_ */
--
2.11.1
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 3/7] clk: sunxi-ng: add support for Allwinner H5 SoC
2017-02-26 1:19 ` Icenowy Zheng
(?)
@ 2017-02-26 1:19 ` Icenowy Zheng
-1 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
Allwinner H5 is a SoC that features a CCU like H3, but with MMC phase
clocks removed (for new MMC controller) and a new bus gate/reset
imported.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
Changes since v5:
- Make all structures dedicated per SoC.
Changes since v3:
- Add a dedicated reset line list for H5, as SCR1 reset is not valid
on H3.
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
drivers/clk/sunxi-ng/Kconfig | 2 +-
drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c | 321 ++++++++++++++++++++-
drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h | 3 +-
include/dt-bindings/clock/sunxi-h3-h5-ccu.h | 3 +
include/dt-bindings/reset/sunxi-h3-h5-ccu.h | 3 +
6 files changed, 324 insertions(+), 9 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
index bae5668cf427..68512aa398a9 100644
--- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
@@ -10,6 +10,7 @@ Required properties :
- "allwinner,sun8i-v3s-ccu"
- "allwinner,sun9i-a80-ccu"
- "allwinner,sun50i-a64-ccu"
+ - "allwinner,sun50i-h5-ccu"
- reg: Must contain the registers base address and length
- clocks: phandle to the oscillators feeding the CCU. Two are needed:
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index af6a5a5dd549..6daddb7df1bc 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -118,7 +118,7 @@ config SUNXI_H3_H5_CCU
select SUNXI_CCU_NM
select SUNXI_CCU_MP
select SUNXI_CCU_PHASE
- default MACH_SUN8I
+ default MACH_SUN8I || (ARM64 && ARCH_SUNXI)
config SUN8I_V3S_CCU
bool "Support for the Allwinner V3s CCU"
diff --git a/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
index e2d065973794..a94eed1b61e4 100644
--- a/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
@@ -302,6 +302,8 @@ static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
0x06c, BIT(19), 0);
static SUNXI_CCU_GATE(bus_scr0_clk, "bus-scr0", "apb2",
0x06c, BIT(20), 0);
+static SUNXI_CCU_GATE(bus_scr1_clk, "bus-scr1", "apb2",
+ 0x06c, BIT(21), 0);
static SUNXI_CCU_GATE(bus_ephy_clk, "bus-ephy", "ahb1",
0x070, BIT(0), 0);
@@ -484,7 +486,7 @@ static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents,
static SUNXI_CCU_M_WITH_GATE(gpu_clk, "gpu", "pll-gpu",
0x1a0, 0, 3, BIT(31), 0);
-static struct ccu_common *sunxi_h3_h5_ccu_clks[] = {
+static struct ccu_common *sun8i_h3_ccu_clks[] = {
&pll_cpux_clk.common,
&pll_audio_base_clk.common,
&pll_video_clk.common,
@@ -597,6 +599,114 @@ static struct ccu_common *sunxi_h3_h5_ccu_clks[] = {
&gpu_clk.common,
};
+static struct ccu_common *sun50i_h5_ccu_clks[] = {
+ &pll_cpux_clk.common,
+ &pll_audio_base_clk.common,
+ &pll_video_clk.common,
+ &pll_ve_clk.common,
+ &pll_ddr_clk.common,
+ &pll_periph0_clk.common,
+ &pll_gpu_clk.common,
+ &pll_periph1_clk.common,
+ &pll_de_clk.common,
+ &cpux_clk.common,
+ &axi_clk.common,
+ &ahb1_clk.common,
+ &apb1_clk.common,
+ &apb2_clk.common,
+ &ahb2_clk.common,
+ &bus_ce_clk.common,
+ &bus_dma_clk.common,
+ &bus_mmc0_clk.common,
+ &bus_mmc1_clk.common,
+ &bus_mmc2_clk.common,
+ &bus_nand_clk.common,
+ &bus_dram_clk.common,
+ &bus_emac_clk.common,
+ &bus_ts_clk.common,
+ &bus_hstimer_clk.common,
+ &bus_spi0_clk.common,
+ &bus_spi1_clk.common,
+ &bus_otg_clk.common,
+ &bus_ehci0_clk.common,
+ &bus_ehci1_clk.common,
+ &bus_ehci2_clk.common,
+ &bus_ehci3_clk.common,
+ &bus_ohci0_clk.common,
+ &bus_ohci1_clk.common,
+ &bus_ohci2_clk.common,
+ &bus_ohci3_clk.common,
+ &bus_ve_clk.common,
+ &bus_tcon0_clk.common,
+ &bus_tcon1_clk.common,
+ &bus_deinterlace_clk.common,
+ &bus_csi_clk.common,
+ &bus_tve_clk.common,
+ &bus_hdmi_clk.common,
+ &bus_de_clk.common,
+ &bus_gpu_clk.common,
+ &bus_msgbox_clk.common,
+ &bus_spinlock_clk.common,
+ &bus_codec_clk.common,
+ &bus_spdif_clk.common,
+ &bus_pio_clk.common,
+ &bus_ths_clk.common,
+ &bus_i2s0_clk.common,
+ &bus_i2s1_clk.common,
+ &bus_i2s2_clk.common,
+ &bus_i2c0_clk.common,
+ &bus_i2c1_clk.common,
+ &bus_i2c2_clk.common,
+ &bus_uart0_clk.common,
+ &bus_uart1_clk.common,
+ &bus_uart2_clk.common,
+ &bus_uart3_clk.common,
+ &bus_scr0_clk.common,
+ &bus_scr1_clk.common,
+ &bus_ephy_clk.common,
+ &bus_dbg_clk.common,
+ &ths_clk.common,
+ &nand_clk.common,
+ &mmc0_clk.common,
+ &mmc1_clk.common,
+ &mmc2_clk.common,
+ &ts_clk.common,
+ &ce_clk.common,
+ &spi0_clk.common,
+ &spi1_clk.common,
+ &i2s0_clk.common,
+ &i2s1_clk.common,
+ &i2s2_clk.common,
+ &spdif_clk.common,
+ &usb_phy0_clk.common,
+ &usb_phy1_clk.common,
+ &usb_phy2_clk.common,
+ &usb_phy3_clk.common,
+ &usb_ohci0_clk.common,
+ &usb_ohci1_clk.common,
+ &usb_ohci2_clk.common,
+ &usb_ohci3_clk.common,
+ &dram_clk.common,
+ &dram_ve_clk.common,
+ &dram_csi_clk.common,
+ &dram_deinterlace_clk.common,
+ &dram_ts_clk.common,
+ &de_clk.common,
+ &tcon_clk.common,
+ &tve_clk.common,
+ &deinterlace_clk.common,
+ &csi_misc_clk.common,
+ &csi_sclk_clk.common,
+ &csi_mclk_clk.common,
+ &ve_clk.common,
+ &ac_dig_clk.common,
+ &avs_clk.common,
+ &hdmi_clk.common,
+ &hdmi_ddc_clk.common,
+ &mbus_clk.common,
+ &gpu_clk.common,
+};
+
/* We hardcode the divider to 4 for now */
static CLK_FIXED_FACTOR(pll_audio_clk, "pll-audio",
"pll-audio-base", 4, 1, CLK_SET_RATE_PARENT);
@@ -727,10 +837,189 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
[CLK_MBUS] = &mbus_clk.common.hw,
[CLK_GPU] = &gpu_clk.common.hw,
},
- .num = CLK_NUMBER,
+ .num = CLK_NUMBER_H3,
+};
+
+static struct clk_hw_onecell_data sun50i_h5_hw_clks = {
+ .hws = {
+ [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw,
+ [CLK_PLL_AUDIO_BASE] = &pll_audio_base_clk.common.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.hw,
+ [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
+ [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
+ [CLK_PLL_AUDIO_8X] = &pll_audio_8x_clk.hw,
+ [CLK_PLL_VIDEO] = &pll_video_clk.common.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_DDR] = &pll_ddr_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_DE] = &pll_de_clk.common.hw,
+ [CLK_CPUX] = &cpux_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_AHB1] = &ahb1_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_AHB2] = &ahb2_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
+ [CLK_BUS_TS] = &bus_ts_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_EHCI2] = &bus_ehci2_clk.common.hw,
+ [CLK_BUS_EHCI3] = &bus_ehci3_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_OHCI2] = &bus_ohci2_clk.common.hw,
+ [CLK_BUS_OHCI3] = &bus_ohci3_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_TCON0] = &bus_tcon0_clk.common.hw,
+ [CLK_BUS_TCON1] = &bus_tcon1_clk.common.hw,
+ [CLK_BUS_DEINTERLACE] = &bus_deinterlace_clk.common.hw,
+ [CLK_BUS_CSI] = &bus_csi_clk.common.hw,
+ [CLK_BUS_TVE] = &bus_tve_clk.common.hw,
+ [CLK_BUS_HDMI] = &bus_hdmi_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw,
+ [CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw,
+ [CLK_BUS_CODEC] = &bus_codec_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_BUS_PIO] = &bus_pio_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
+ [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
+ [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
+ [CLK_BUS_SCR1] = &bus_scr1_clk.common.hw,
+ [CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_THS] = &ths_clk.common.hw,
+ [CLK_NAND] = &nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_TS] = &ts_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_I2S0] = &i2s0_clk.common.hw,
+ [CLK_I2S1] = &i2s1_clk.common.hw,
+ [CLK_I2S2] = &i2s2_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_USB_PHY2] = &usb_phy2_clk.common.hw,
+ [CLK_USB_PHY3] = &usb_phy3_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw,
+ [CLK_USB_OHCI3] = &usb_ohci3_clk.common.hw,
+ [CLK_DRAM] = &dram_clk.common.hw,
+ [CLK_DRAM_VE] = &dram_ve_clk.common.hw,
+ [CLK_DRAM_CSI] = &dram_csi_clk.common.hw,
+ [CLK_DRAM_DEINTERLACE] = &dram_deinterlace_clk.common.hw,
+ [CLK_DRAM_TS] = &dram_ts_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_TCON0] = &tcon_clk.common.hw,
+ [CLK_TVE] = &tve_clk.common.hw,
+ [CLK_DEINTERLACE] = &deinterlace_clk.common.hw,
+ [CLK_CSI_MISC] = &csi_misc_clk.common.hw,
+ [CLK_CSI_SCLK] = &csi_sclk_clk.common.hw,
+ [CLK_CSI_MCLK] = &csi_mclk_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_AC_DIG] = &ac_dig_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_HDMI] = &hdmi_clk.common.hw,
+ [CLK_HDMI_DDC] = &hdmi_ddc_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ },
+ .num = CLK_NUMBER_H5,
+};
+
+static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
+ [RST_USB_PHY0] = { 0x0cc, BIT(0) },
+ [RST_USB_PHY1] = { 0x0cc, BIT(1) },
+ [RST_USB_PHY2] = { 0x0cc, BIT(2) },
+ [RST_USB_PHY3] = { 0x0cc, BIT(3) },
+
+ [RST_MBUS] = { 0x0fc, BIT(31) },
+
+ [RST_BUS_CE] = { 0x2c0, BIT(5) },
+ [RST_BUS_DMA] = { 0x2c0, BIT(6) },
+ [RST_BUS_MMC0] = { 0x2c0, BIT(8) },
+ [RST_BUS_MMC1] = { 0x2c0, BIT(9) },
+ [RST_BUS_MMC2] = { 0x2c0, BIT(10) },
+ [RST_BUS_NAND] = { 0x2c0, BIT(13) },
+ [RST_BUS_DRAM] = { 0x2c0, BIT(14) },
+ [RST_BUS_EMAC] = { 0x2c0, BIT(17) },
+ [RST_BUS_TS] = { 0x2c0, BIT(18) },
+ [RST_BUS_HSTIMER] = { 0x2c0, BIT(19) },
+ [RST_BUS_SPI0] = { 0x2c0, BIT(20) },
+ [RST_BUS_SPI1] = { 0x2c0, BIT(21) },
+ [RST_BUS_OTG] = { 0x2c0, BIT(23) },
+ [RST_BUS_EHCI0] = { 0x2c0, BIT(24) },
+ [RST_BUS_EHCI1] = { 0x2c0, BIT(25) },
+ [RST_BUS_EHCI2] = { 0x2c0, BIT(26) },
+ [RST_BUS_EHCI3] = { 0x2c0, BIT(27) },
+ [RST_BUS_OHCI0] = { 0x2c0, BIT(28) },
+ [RST_BUS_OHCI1] = { 0x2c0, BIT(29) },
+ [RST_BUS_OHCI2] = { 0x2c0, BIT(30) },
+ [RST_BUS_OHCI3] = { 0x2c0, BIT(31) },
+
+ [RST_BUS_VE] = { 0x2c4, BIT(0) },
+ [RST_BUS_TCON0] = { 0x2c4, BIT(3) },
+ [RST_BUS_TCON1] = { 0x2c4, BIT(4) },
+ [RST_BUS_DEINTERLACE] = { 0x2c4, BIT(5) },
+ [RST_BUS_CSI] = { 0x2c4, BIT(8) },
+ [RST_BUS_TVE] = { 0x2c4, BIT(9) },
+ [RST_BUS_HDMI0] = { 0x2c4, BIT(10) },
+ [RST_BUS_HDMI1] = { 0x2c4, BIT(11) },
+ [RST_BUS_DE] = { 0x2c4, BIT(12) },
+ [RST_BUS_GPU] = { 0x2c4, BIT(20) },
+ [RST_BUS_MSGBOX] = { 0x2c4, BIT(21) },
+ [RST_BUS_SPINLOCK] = { 0x2c4, BIT(22) },
+ [RST_BUS_DBG] = { 0x2c4, BIT(31) },
+
+ [RST_BUS_EPHY] = { 0x2c8, BIT(2) },
+
+ [RST_BUS_CODEC] = { 0x2d0, BIT(0) },
+ [RST_BUS_SPDIF] = { 0x2d0, BIT(1) },
+ [RST_BUS_THS] = { 0x2d0, BIT(8) },
+ [RST_BUS_I2S0] = { 0x2d0, BIT(12) },
+ [RST_BUS_I2S1] = { 0x2d0, BIT(13) },
+ [RST_BUS_I2S2] = { 0x2d0, BIT(14) },
+
+ [RST_BUS_I2C0] = { 0x2d8, BIT(0) },
+ [RST_BUS_I2C1] = { 0x2d8, BIT(1) },
+ [RST_BUS_I2C2] = { 0x2d8, BIT(2) },
+ [RST_BUS_UART0] = { 0x2d8, BIT(16) },
+ [RST_BUS_UART1] = { 0x2d8, BIT(17) },
+ [RST_BUS_UART2] = { 0x2d8, BIT(18) },
+ [RST_BUS_UART3] = { 0x2d8, BIT(19) },
+ [RST_BUS_SCR0] = { 0x2d8, BIT(20) },
};
-static struct ccu_reset_map sunxi_h3_h5_ccu_resets[] = {
+static struct ccu_reset_map sun50i_h5_ccu_resets[] = {
[RST_USB_PHY0] = { 0x0cc, BIT(0) },
[RST_USB_PHY1] = { 0x0cc, BIT(1) },
[RST_USB_PHY2] = { 0x0cc, BIT(2) },
@@ -791,16 +1080,27 @@ static struct ccu_reset_map sunxi_h3_h5_ccu_resets[] = {
[RST_BUS_UART2] = { 0x2d8, BIT(18) },
[RST_BUS_UART3] = { 0x2d8, BIT(19) },
[RST_BUS_SCR0] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR1] = { 0x2d8, BIT(21) },
};
static const struct sunxi_ccu_desc sun8i_h3_ccu_desc = {
- .ccu_clks = sunxi_h3_h5_ccu_clks,
- .num_ccu_clks = ARRAY_SIZE(sunxi_h3_h5_ccu_clks),
+ .ccu_clks = sun8i_h3_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun8i_h3_ccu_clks),
.hw_clks = &sun8i_h3_hw_clks,
- .resets = sunxi_h3_h5_ccu_resets,
- .num_resets = ARRAY_SIZE(sunxi_h3_h5_ccu_resets),
+ .resets = sun8i_h3_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun8i_h3_ccu_resets),
+};
+
+static const struct sunxi_ccu_desc sun50i_h5_ccu_desc = {
+ .ccu_clks = sun50i_h5_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_h5_ccu_clks),
+
+ .hw_clks = &sun50i_h5_hw_clks,
+
+ .resets = sun50i_h5_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_h5_ccu_resets),
};
static struct ccu_mux_nb sunxi_h3_h5_cpu_nb = {
@@ -840,3 +1140,10 @@ static void __init sun8i_h3_ccu_setup(struct device_node *node)
}
CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
sun8i_h3_ccu_setup);
+
+static void __init sun50i_h5_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun50i_h5_ccu_desc);
+}
+CLK_OF_DECLARE(sun50i_h5_ccu, "allwinner,sun50i-h5-ccu",
+ sun50i_h5_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
index e2a4656d2cf3..cc918a00033b 100644
--- a/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
@@ -57,6 +57,7 @@
/* And the GPU module clock is exported */
-#define CLK_NUMBER (CLK_GPU + 1)
+#define CLK_NUMBER_H3 (CLK_GPU + 1)
+#define CLK_NUMBER_H5 (CLK_BUS_SCR1 + 1)
#endif /* _CCU_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/clock/sunxi-h3-h5-ccu.h b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
index 1715a5e12525..4899eacef71d 100644
--- a/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
+++ b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
@@ -142,4 +142,7 @@
#define CLK_GPU 114
+/* New clocks imported in H5 */
+#define CLK_BUS_SCR1 115
+
#endif /* _DT_BINDINGS_CLK_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/reset/sunxi-h3-h5-ccu.h b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
index 7a5de896cf1f..1084c157c062 100644
--- a/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
+++ b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
@@ -100,4 +100,7 @@
#define RST_BUS_UART3 52
#define RST_BUS_SCR0 53
+/* New resets imported in H5 */
+#define RST_BUS_SCR1 54
+
#endif /* _DT_BINDINGS_RST_SUNXI_H3_H5_H_ */
--
2.11.1
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 3/7] clk: sunxi-ng: add support for Allwinner H5 SoC
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara
Cc: devicetree, linux-kernel, linux-sunxi, Icenowy Zheng, linux-clk,
linux-arm-kernel
Allwinner H5 is a SoC that features a CCU like H3, but with MMC phase
clocks removed (for new MMC controller) and a new bus gate/reset
imported.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes since v5:
- Make all structures dedicated per SoC.
Changes since v3:
- Add a dedicated reset line list for H5, as SCR1 reset is not valid
on H3.
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
drivers/clk/sunxi-ng/Kconfig | 2 +-
drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c | 321 ++++++++++++++++++++-
drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h | 3 +-
include/dt-bindings/clock/sunxi-h3-h5-ccu.h | 3 +
include/dt-bindings/reset/sunxi-h3-h5-ccu.h | 3 +
6 files changed, 324 insertions(+), 9 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
index bae5668cf427..68512aa398a9 100644
--- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
@@ -10,6 +10,7 @@ Required properties :
- "allwinner,sun8i-v3s-ccu"
- "allwinner,sun9i-a80-ccu"
- "allwinner,sun50i-a64-ccu"
+ - "allwinner,sun50i-h5-ccu"
- reg: Must contain the registers base address and length
- clocks: phandle to the oscillators feeding the CCU. Two are needed:
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index af6a5a5dd549..6daddb7df1bc 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -118,7 +118,7 @@ config SUNXI_H3_H5_CCU
select SUNXI_CCU_NM
select SUNXI_CCU_MP
select SUNXI_CCU_PHASE
- default MACH_SUN8I
+ default MACH_SUN8I || (ARM64 && ARCH_SUNXI)
config SUN8I_V3S_CCU
bool "Support for the Allwinner V3s CCU"
diff --git a/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
index e2d065973794..a94eed1b61e4 100644
--- a/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
@@ -302,6 +302,8 @@ static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
0x06c, BIT(19), 0);
static SUNXI_CCU_GATE(bus_scr0_clk, "bus-scr0", "apb2",
0x06c, BIT(20), 0);
+static SUNXI_CCU_GATE(bus_scr1_clk, "bus-scr1", "apb2",
+ 0x06c, BIT(21), 0);
static SUNXI_CCU_GATE(bus_ephy_clk, "bus-ephy", "ahb1",
0x070, BIT(0), 0);
@@ -484,7 +486,7 @@ static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents,
static SUNXI_CCU_M_WITH_GATE(gpu_clk, "gpu", "pll-gpu",
0x1a0, 0, 3, BIT(31), 0);
-static struct ccu_common *sunxi_h3_h5_ccu_clks[] = {
+static struct ccu_common *sun8i_h3_ccu_clks[] = {
&pll_cpux_clk.common,
&pll_audio_base_clk.common,
&pll_video_clk.common,
@@ -597,6 +599,114 @@ static struct ccu_common *sunxi_h3_h5_ccu_clks[] = {
&gpu_clk.common,
};
+static struct ccu_common *sun50i_h5_ccu_clks[] = {
+ &pll_cpux_clk.common,
+ &pll_audio_base_clk.common,
+ &pll_video_clk.common,
+ &pll_ve_clk.common,
+ &pll_ddr_clk.common,
+ &pll_periph0_clk.common,
+ &pll_gpu_clk.common,
+ &pll_periph1_clk.common,
+ &pll_de_clk.common,
+ &cpux_clk.common,
+ &axi_clk.common,
+ &ahb1_clk.common,
+ &apb1_clk.common,
+ &apb2_clk.common,
+ &ahb2_clk.common,
+ &bus_ce_clk.common,
+ &bus_dma_clk.common,
+ &bus_mmc0_clk.common,
+ &bus_mmc1_clk.common,
+ &bus_mmc2_clk.common,
+ &bus_nand_clk.common,
+ &bus_dram_clk.common,
+ &bus_emac_clk.common,
+ &bus_ts_clk.common,
+ &bus_hstimer_clk.common,
+ &bus_spi0_clk.common,
+ &bus_spi1_clk.common,
+ &bus_otg_clk.common,
+ &bus_ehci0_clk.common,
+ &bus_ehci1_clk.common,
+ &bus_ehci2_clk.common,
+ &bus_ehci3_clk.common,
+ &bus_ohci0_clk.common,
+ &bus_ohci1_clk.common,
+ &bus_ohci2_clk.common,
+ &bus_ohci3_clk.common,
+ &bus_ve_clk.common,
+ &bus_tcon0_clk.common,
+ &bus_tcon1_clk.common,
+ &bus_deinterlace_clk.common,
+ &bus_csi_clk.common,
+ &bus_tve_clk.common,
+ &bus_hdmi_clk.common,
+ &bus_de_clk.common,
+ &bus_gpu_clk.common,
+ &bus_msgbox_clk.common,
+ &bus_spinlock_clk.common,
+ &bus_codec_clk.common,
+ &bus_spdif_clk.common,
+ &bus_pio_clk.common,
+ &bus_ths_clk.common,
+ &bus_i2s0_clk.common,
+ &bus_i2s1_clk.common,
+ &bus_i2s2_clk.common,
+ &bus_i2c0_clk.common,
+ &bus_i2c1_clk.common,
+ &bus_i2c2_clk.common,
+ &bus_uart0_clk.common,
+ &bus_uart1_clk.common,
+ &bus_uart2_clk.common,
+ &bus_uart3_clk.common,
+ &bus_scr0_clk.common,
+ &bus_scr1_clk.common,
+ &bus_ephy_clk.common,
+ &bus_dbg_clk.common,
+ &ths_clk.common,
+ &nand_clk.common,
+ &mmc0_clk.common,
+ &mmc1_clk.common,
+ &mmc2_clk.common,
+ &ts_clk.common,
+ &ce_clk.common,
+ &spi0_clk.common,
+ &spi1_clk.common,
+ &i2s0_clk.common,
+ &i2s1_clk.common,
+ &i2s2_clk.common,
+ &spdif_clk.common,
+ &usb_phy0_clk.common,
+ &usb_phy1_clk.common,
+ &usb_phy2_clk.common,
+ &usb_phy3_clk.common,
+ &usb_ohci0_clk.common,
+ &usb_ohci1_clk.common,
+ &usb_ohci2_clk.common,
+ &usb_ohci3_clk.common,
+ &dram_clk.common,
+ &dram_ve_clk.common,
+ &dram_csi_clk.common,
+ &dram_deinterlace_clk.common,
+ &dram_ts_clk.common,
+ &de_clk.common,
+ &tcon_clk.common,
+ &tve_clk.common,
+ &deinterlace_clk.common,
+ &csi_misc_clk.common,
+ &csi_sclk_clk.common,
+ &csi_mclk_clk.common,
+ &ve_clk.common,
+ &ac_dig_clk.common,
+ &avs_clk.common,
+ &hdmi_clk.common,
+ &hdmi_ddc_clk.common,
+ &mbus_clk.common,
+ &gpu_clk.common,
+};
+
/* We hardcode the divider to 4 for now */
static CLK_FIXED_FACTOR(pll_audio_clk, "pll-audio",
"pll-audio-base", 4, 1, CLK_SET_RATE_PARENT);
@@ -727,10 +837,189 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
[CLK_MBUS] = &mbus_clk.common.hw,
[CLK_GPU] = &gpu_clk.common.hw,
},
- .num = CLK_NUMBER,
+ .num = CLK_NUMBER_H3,
+};
+
+static struct clk_hw_onecell_data sun50i_h5_hw_clks = {
+ .hws = {
+ [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw,
+ [CLK_PLL_AUDIO_BASE] = &pll_audio_base_clk.common.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.hw,
+ [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
+ [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
+ [CLK_PLL_AUDIO_8X] = &pll_audio_8x_clk.hw,
+ [CLK_PLL_VIDEO] = &pll_video_clk.common.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_DDR] = &pll_ddr_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_DE] = &pll_de_clk.common.hw,
+ [CLK_CPUX] = &cpux_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_AHB1] = &ahb1_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_AHB2] = &ahb2_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
+ [CLK_BUS_TS] = &bus_ts_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_EHCI2] = &bus_ehci2_clk.common.hw,
+ [CLK_BUS_EHCI3] = &bus_ehci3_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_OHCI2] = &bus_ohci2_clk.common.hw,
+ [CLK_BUS_OHCI3] = &bus_ohci3_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_TCON0] = &bus_tcon0_clk.common.hw,
+ [CLK_BUS_TCON1] = &bus_tcon1_clk.common.hw,
+ [CLK_BUS_DEINTERLACE] = &bus_deinterlace_clk.common.hw,
+ [CLK_BUS_CSI] = &bus_csi_clk.common.hw,
+ [CLK_BUS_TVE] = &bus_tve_clk.common.hw,
+ [CLK_BUS_HDMI] = &bus_hdmi_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw,
+ [CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw,
+ [CLK_BUS_CODEC] = &bus_codec_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_BUS_PIO] = &bus_pio_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
+ [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
+ [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
+ [CLK_BUS_SCR1] = &bus_scr1_clk.common.hw,
+ [CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_THS] = &ths_clk.common.hw,
+ [CLK_NAND] = &nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_TS] = &ts_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_I2S0] = &i2s0_clk.common.hw,
+ [CLK_I2S1] = &i2s1_clk.common.hw,
+ [CLK_I2S2] = &i2s2_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_USB_PHY2] = &usb_phy2_clk.common.hw,
+ [CLK_USB_PHY3] = &usb_phy3_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw,
+ [CLK_USB_OHCI3] = &usb_ohci3_clk.common.hw,
+ [CLK_DRAM] = &dram_clk.common.hw,
+ [CLK_DRAM_VE] = &dram_ve_clk.common.hw,
+ [CLK_DRAM_CSI] = &dram_csi_clk.common.hw,
+ [CLK_DRAM_DEINTERLACE] = &dram_deinterlace_clk.common.hw,
+ [CLK_DRAM_TS] = &dram_ts_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_TCON0] = &tcon_clk.common.hw,
+ [CLK_TVE] = &tve_clk.common.hw,
+ [CLK_DEINTERLACE] = &deinterlace_clk.common.hw,
+ [CLK_CSI_MISC] = &csi_misc_clk.common.hw,
+ [CLK_CSI_SCLK] = &csi_sclk_clk.common.hw,
+ [CLK_CSI_MCLK] = &csi_mclk_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_AC_DIG] = &ac_dig_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_HDMI] = &hdmi_clk.common.hw,
+ [CLK_HDMI_DDC] = &hdmi_ddc_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ },
+ .num = CLK_NUMBER_H5,
+};
+
+static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
+ [RST_USB_PHY0] = { 0x0cc, BIT(0) },
+ [RST_USB_PHY1] = { 0x0cc, BIT(1) },
+ [RST_USB_PHY2] = { 0x0cc, BIT(2) },
+ [RST_USB_PHY3] = { 0x0cc, BIT(3) },
+
+ [RST_MBUS] = { 0x0fc, BIT(31) },
+
+ [RST_BUS_CE] = { 0x2c0, BIT(5) },
+ [RST_BUS_DMA] = { 0x2c0, BIT(6) },
+ [RST_BUS_MMC0] = { 0x2c0, BIT(8) },
+ [RST_BUS_MMC1] = { 0x2c0, BIT(9) },
+ [RST_BUS_MMC2] = { 0x2c0, BIT(10) },
+ [RST_BUS_NAND] = { 0x2c0, BIT(13) },
+ [RST_BUS_DRAM] = { 0x2c0, BIT(14) },
+ [RST_BUS_EMAC] = { 0x2c0, BIT(17) },
+ [RST_BUS_TS] = { 0x2c0, BIT(18) },
+ [RST_BUS_HSTIMER] = { 0x2c0, BIT(19) },
+ [RST_BUS_SPI0] = { 0x2c0, BIT(20) },
+ [RST_BUS_SPI1] = { 0x2c0, BIT(21) },
+ [RST_BUS_OTG] = { 0x2c0, BIT(23) },
+ [RST_BUS_EHCI0] = { 0x2c0, BIT(24) },
+ [RST_BUS_EHCI1] = { 0x2c0, BIT(25) },
+ [RST_BUS_EHCI2] = { 0x2c0, BIT(26) },
+ [RST_BUS_EHCI3] = { 0x2c0, BIT(27) },
+ [RST_BUS_OHCI0] = { 0x2c0, BIT(28) },
+ [RST_BUS_OHCI1] = { 0x2c0, BIT(29) },
+ [RST_BUS_OHCI2] = { 0x2c0, BIT(30) },
+ [RST_BUS_OHCI3] = { 0x2c0, BIT(31) },
+
+ [RST_BUS_VE] = { 0x2c4, BIT(0) },
+ [RST_BUS_TCON0] = { 0x2c4, BIT(3) },
+ [RST_BUS_TCON1] = { 0x2c4, BIT(4) },
+ [RST_BUS_DEINTERLACE] = { 0x2c4, BIT(5) },
+ [RST_BUS_CSI] = { 0x2c4, BIT(8) },
+ [RST_BUS_TVE] = { 0x2c4, BIT(9) },
+ [RST_BUS_HDMI0] = { 0x2c4, BIT(10) },
+ [RST_BUS_HDMI1] = { 0x2c4, BIT(11) },
+ [RST_BUS_DE] = { 0x2c4, BIT(12) },
+ [RST_BUS_GPU] = { 0x2c4, BIT(20) },
+ [RST_BUS_MSGBOX] = { 0x2c4, BIT(21) },
+ [RST_BUS_SPINLOCK] = { 0x2c4, BIT(22) },
+ [RST_BUS_DBG] = { 0x2c4, BIT(31) },
+
+ [RST_BUS_EPHY] = { 0x2c8, BIT(2) },
+
+ [RST_BUS_CODEC] = { 0x2d0, BIT(0) },
+ [RST_BUS_SPDIF] = { 0x2d0, BIT(1) },
+ [RST_BUS_THS] = { 0x2d0, BIT(8) },
+ [RST_BUS_I2S0] = { 0x2d0, BIT(12) },
+ [RST_BUS_I2S1] = { 0x2d0, BIT(13) },
+ [RST_BUS_I2S2] = { 0x2d0, BIT(14) },
+
+ [RST_BUS_I2C0] = { 0x2d8, BIT(0) },
+ [RST_BUS_I2C1] = { 0x2d8, BIT(1) },
+ [RST_BUS_I2C2] = { 0x2d8, BIT(2) },
+ [RST_BUS_UART0] = { 0x2d8, BIT(16) },
+ [RST_BUS_UART1] = { 0x2d8, BIT(17) },
+ [RST_BUS_UART2] = { 0x2d8, BIT(18) },
+ [RST_BUS_UART3] = { 0x2d8, BIT(19) },
+ [RST_BUS_SCR0] = { 0x2d8, BIT(20) },
};
-static struct ccu_reset_map sunxi_h3_h5_ccu_resets[] = {
+static struct ccu_reset_map sun50i_h5_ccu_resets[] = {
[RST_USB_PHY0] = { 0x0cc, BIT(0) },
[RST_USB_PHY1] = { 0x0cc, BIT(1) },
[RST_USB_PHY2] = { 0x0cc, BIT(2) },
@@ -791,16 +1080,27 @@ static struct ccu_reset_map sunxi_h3_h5_ccu_resets[] = {
[RST_BUS_UART2] = { 0x2d8, BIT(18) },
[RST_BUS_UART3] = { 0x2d8, BIT(19) },
[RST_BUS_SCR0] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR1] = { 0x2d8, BIT(21) },
};
static const struct sunxi_ccu_desc sun8i_h3_ccu_desc = {
- .ccu_clks = sunxi_h3_h5_ccu_clks,
- .num_ccu_clks = ARRAY_SIZE(sunxi_h3_h5_ccu_clks),
+ .ccu_clks = sun8i_h3_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun8i_h3_ccu_clks),
.hw_clks = &sun8i_h3_hw_clks,
- .resets = sunxi_h3_h5_ccu_resets,
- .num_resets = ARRAY_SIZE(sunxi_h3_h5_ccu_resets),
+ .resets = sun8i_h3_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun8i_h3_ccu_resets),
+};
+
+static const struct sunxi_ccu_desc sun50i_h5_ccu_desc = {
+ .ccu_clks = sun50i_h5_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_h5_ccu_clks),
+
+ .hw_clks = &sun50i_h5_hw_clks,
+
+ .resets = sun50i_h5_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_h5_ccu_resets),
};
static struct ccu_mux_nb sunxi_h3_h5_cpu_nb = {
@@ -840,3 +1140,10 @@ static void __init sun8i_h3_ccu_setup(struct device_node *node)
}
CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
sun8i_h3_ccu_setup);
+
+static void __init sun50i_h5_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun50i_h5_ccu_desc);
+}
+CLK_OF_DECLARE(sun50i_h5_ccu, "allwinner,sun50i-h5-ccu",
+ sun50i_h5_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
index e2a4656d2cf3..cc918a00033b 100644
--- a/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
@@ -57,6 +57,7 @@
/* And the GPU module clock is exported */
-#define CLK_NUMBER (CLK_GPU + 1)
+#define CLK_NUMBER_H3 (CLK_GPU + 1)
+#define CLK_NUMBER_H5 (CLK_BUS_SCR1 + 1)
#endif /* _CCU_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/clock/sunxi-h3-h5-ccu.h b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
index 1715a5e12525..4899eacef71d 100644
--- a/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
+++ b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
@@ -142,4 +142,7 @@
#define CLK_GPU 114
+/* New clocks imported in H5 */
+#define CLK_BUS_SCR1 115
+
#endif /* _DT_BINDINGS_CLK_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/reset/sunxi-h3-h5-ccu.h b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
index 7a5de896cf1f..1084c157c062 100644
--- a/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
+++ b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
@@ -100,4 +100,7 @@
#define RST_BUS_UART3 52
#define RST_BUS_SCR0 53
+/* New resets imported in H5 */
+#define RST_BUS_SCR1 54
+
#endif /* _DT_BINDINGS_RST_SUNXI_H3_H5_H_ */
--
2.11.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 3/7] clk: sunxi-ng: add support for Allwinner H5 SoC
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: linux-arm-kernel
Allwinner H5 is a SoC that features a CCU like H3, but with MMC phase
clocks removed (for new MMC controller) and a new bus gate/reset
imported.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes since v5:
- Make all structures dedicated per SoC.
Changes since v3:
- Add a dedicated reset line list for H5, as SCR1 reset is not valid
on H3.
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
drivers/clk/sunxi-ng/Kconfig | 2 +-
drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c | 321 ++++++++++++++++++++-
drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h | 3 +-
include/dt-bindings/clock/sunxi-h3-h5-ccu.h | 3 +
include/dt-bindings/reset/sunxi-h3-h5-ccu.h | 3 +
6 files changed, 324 insertions(+), 9 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
index bae5668cf427..68512aa398a9 100644
--- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
@@ -10,6 +10,7 @@ Required properties :
- "allwinner,sun8i-v3s-ccu"
- "allwinner,sun9i-a80-ccu"
- "allwinner,sun50i-a64-ccu"
+ - "allwinner,sun50i-h5-ccu"
- reg: Must contain the registers base address and length
- clocks: phandle to the oscillators feeding the CCU. Two are needed:
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index af6a5a5dd549..6daddb7df1bc 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -118,7 +118,7 @@ config SUNXI_H3_H5_CCU
select SUNXI_CCU_NM
select SUNXI_CCU_MP
select SUNXI_CCU_PHASE
- default MACH_SUN8I
+ default MACH_SUN8I || (ARM64 && ARCH_SUNXI)
config SUN8I_V3S_CCU
bool "Support for the Allwinner V3s CCU"
diff --git a/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
index e2d065973794..a94eed1b61e4 100644
--- a/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
@@ -302,6 +302,8 @@ static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
0x06c, BIT(19), 0);
static SUNXI_CCU_GATE(bus_scr0_clk, "bus-scr0", "apb2",
0x06c, BIT(20), 0);
+static SUNXI_CCU_GATE(bus_scr1_clk, "bus-scr1", "apb2",
+ 0x06c, BIT(21), 0);
static SUNXI_CCU_GATE(bus_ephy_clk, "bus-ephy", "ahb1",
0x070, BIT(0), 0);
@@ -484,7 +486,7 @@ static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents,
static SUNXI_CCU_M_WITH_GATE(gpu_clk, "gpu", "pll-gpu",
0x1a0, 0, 3, BIT(31), 0);
-static struct ccu_common *sunxi_h3_h5_ccu_clks[] = {
+static struct ccu_common *sun8i_h3_ccu_clks[] = {
&pll_cpux_clk.common,
&pll_audio_base_clk.common,
&pll_video_clk.common,
@@ -597,6 +599,114 @@ static struct ccu_common *sunxi_h3_h5_ccu_clks[] = {
&gpu_clk.common,
};
+static struct ccu_common *sun50i_h5_ccu_clks[] = {
+ &pll_cpux_clk.common,
+ &pll_audio_base_clk.common,
+ &pll_video_clk.common,
+ &pll_ve_clk.common,
+ &pll_ddr_clk.common,
+ &pll_periph0_clk.common,
+ &pll_gpu_clk.common,
+ &pll_periph1_clk.common,
+ &pll_de_clk.common,
+ &cpux_clk.common,
+ &axi_clk.common,
+ &ahb1_clk.common,
+ &apb1_clk.common,
+ &apb2_clk.common,
+ &ahb2_clk.common,
+ &bus_ce_clk.common,
+ &bus_dma_clk.common,
+ &bus_mmc0_clk.common,
+ &bus_mmc1_clk.common,
+ &bus_mmc2_clk.common,
+ &bus_nand_clk.common,
+ &bus_dram_clk.common,
+ &bus_emac_clk.common,
+ &bus_ts_clk.common,
+ &bus_hstimer_clk.common,
+ &bus_spi0_clk.common,
+ &bus_spi1_clk.common,
+ &bus_otg_clk.common,
+ &bus_ehci0_clk.common,
+ &bus_ehci1_clk.common,
+ &bus_ehci2_clk.common,
+ &bus_ehci3_clk.common,
+ &bus_ohci0_clk.common,
+ &bus_ohci1_clk.common,
+ &bus_ohci2_clk.common,
+ &bus_ohci3_clk.common,
+ &bus_ve_clk.common,
+ &bus_tcon0_clk.common,
+ &bus_tcon1_clk.common,
+ &bus_deinterlace_clk.common,
+ &bus_csi_clk.common,
+ &bus_tve_clk.common,
+ &bus_hdmi_clk.common,
+ &bus_de_clk.common,
+ &bus_gpu_clk.common,
+ &bus_msgbox_clk.common,
+ &bus_spinlock_clk.common,
+ &bus_codec_clk.common,
+ &bus_spdif_clk.common,
+ &bus_pio_clk.common,
+ &bus_ths_clk.common,
+ &bus_i2s0_clk.common,
+ &bus_i2s1_clk.common,
+ &bus_i2s2_clk.common,
+ &bus_i2c0_clk.common,
+ &bus_i2c1_clk.common,
+ &bus_i2c2_clk.common,
+ &bus_uart0_clk.common,
+ &bus_uart1_clk.common,
+ &bus_uart2_clk.common,
+ &bus_uart3_clk.common,
+ &bus_scr0_clk.common,
+ &bus_scr1_clk.common,
+ &bus_ephy_clk.common,
+ &bus_dbg_clk.common,
+ &ths_clk.common,
+ &nand_clk.common,
+ &mmc0_clk.common,
+ &mmc1_clk.common,
+ &mmc2_clk.common,
+ &ts_clk.common,
+ &ce_clk.common,
+ &spi0_clk.common,
+ &spi1_clk.common,
+ &i2s0_clk.common,
+ &i2s1_clk.common,
+ &i2s2_clk.common,
+ &spdif_clk.common,
+ &usb_phy0_clk.common,
+ &usb_phy1_clk.common,
+ &usb_phy2_clk.common,
+ &usb_phy3_clk.common,
+ &usb_ohci0_clk.common,
+ &usb_ohci1_clk.common,
+ &usb_ohci2_clk.common,
+ &usb_ohci3_clk.common,
+ &dram_clk.common,
+ &dram_ve_clk.common,
+ &dram_csi_clk.common,
+ &dram_deinterlace_clk.common,
+ &dram_ts_clk.common,
+ &de_clk.common,
+ &tcon_clk.common,
+ &tve_clk.common,
+ &deinterlace_clk.common,
+ &csi_misc_clk.common,
+ &csi_sclk_clk.common,
+ &csi_mclk_clk.common,
+ &ve_clk.common,
+ &ac_dig_clk.common,
+ &avs_clk.common,
+ &hdmi_clk.common,
+ &hdmi_ddc_clk.common,
+ &mbus_clk.common,
+ &gpu_clk.common,
+};
+
/* We hardcode the divider to 4 for now */
static CLK_FIXED_FACTOR(pll_audio_clk, "pll-audio",
"pll-audio-base", 4, 1, CLK_SET_RATE_PARENT);
@@ -727,10 +837,189 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
[CLK_MBUS] = &mbus_clk.common.hw,
[CLK_GPU] = &gpu_clk.common.hw,
},
- .num = CLK_NUMBER,
+ .num = CLK_NUMBER_H3,
+};
+
+static struct clk_hw_onecell_data sun50i_h5_hw_clks = {
+ .hws = {
+ [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw,
+ [CLK_PLL_AUDIO_BASE] = &pll_audio_base_clk.common.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.hw,
+ [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
+ [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
+ [CLK_PLL_AUDIO_8X] = &pll_audio_8x_clk.hw,
+ [CLK_PLL_VIDEO] = &pll_video_clk.common.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_DDR] = &pll_ddr_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_DE] = &pll_de_clk.common.hw,
+ [CLK_CPUX] = &cpux_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_AHB1] = &ahb1_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_AHB2] = &ahb2_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
+ [CLK_BUS_TS] = &bus_ts_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_EHCI2] = &bus_ehci2_clk.common.hw,
+ [CLK_BUS_EHCI3] = &bus_ehci3_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_OHCI2] = &bus_ohci2_clk.common.hw,
+ [CLK_BUS_OHCI3] = &bus_ohci3_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_TCON0] = &bus_tcon0_clk.common.hw,
+ [CLK_BUS_TCON1] = &bus_tcon1_clk.common.hw,
+ [CLK_BUS_DEINTERLACE] = &bus_deinterlace_clk.common.hw,
+ [CLK_BUS_CSI] = &bus_csi_clk.common.hw,
+ [CLK_BUS_TVE] = &bus_tve_clk.common.hw,
+ [CLK_BUS_HDMI] = &bus_hdmi_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw,
+ [CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw,
+ [CLK_BUS_CODEC] = &bus_codec_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_BUS_PIO] = &bus_pio_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
+ [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
+ [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
+ [CLK_BUS_SCR1] = &bus_scr1_clk.common.hw,
+ [CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_THS] = &ths_clk.common.hw,
+ [CLK_NAND] = &nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_TS] = &ts_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_I2S0] = &i2s0_clk.common.hw,
+ [CLK_I2S1] = &i2s1_clk.common.hw,
+ [CLK_I2S2] = &i2s2_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_USB_PHY2] = &usb_phy2_clk.common.hw,
+ [CLK_USB_PHY3] = &usb_phy3_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw,
+ [CLK_USB_OHCI3] = &usb_ohci3_clk.common.hw,
+ [CLK_DRAM] = &dram_clk.common.hw,
+ [CLK_DRAM_VE] = &dram_ve_clk.common.hw,
+ [CLK_DRAM_CSI] = &dram_csi_clk.common.hw,
+ [CLK_DRAM_DEINTERLACE] = &dram_deinterlace_clk.common.hw,
+ [CLK_DRAM_TS] = &dram_ts_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_TCON0] = &tcon_clk.common.hw,
+ [CLK_TVE] = &tve_clk.common.hw,
+ [CLK_DEINTERLACE] = &deinterlace_clk.common.hw,
+ [CLK_CSI_MISC] = &csi_misc_clk.common.hw,
+ [CLK_CSI_SCLK] = &csi_sclk_clk.common.hw,
+ [CLK_CSI_MCLK] = &csi_mclk_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_AC_DIG] = &ac_dig_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_HDMI] = &hdmi_clk.common.hw,
+ [CLK_HDMI_DDC] = &hdmi_ddc_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ },
+ .num = CLK_NUMBER_H5,
+};
+
+static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
+ [RST_USB_PHY0] = { 0x0cc, BIT(0) },
+ [RST_USB_PHY1] = { 0x0cc, BIT(1) },
+ [RST_USB_PHY2] = { 0x0cc, BIT(2) },
+ [RST_USB_PHY3] = { 0x0cc, BIT(3) },
+
+ [RST_MBUS] = { 0x0fc, BIT(31) },
+
+ [RST_BUS_CE] = { 0x2c0, BIT(5) },
+ [RST_BUS_DMA] = { 0x2c0, BIT(6) },
+ [RST_BUS_MMC0] = { 0x2c0, BIT(8) },
+ [RST_BUS_MMC1] = { 0x2c0, BIT(9) },
+ [RST_BUS_MMC2] = { 0x2c0, BIT(10) },
+ [RST_BUS_NAND] = { 0x2c0, BIT(13) },
+ [RST_BUS_DRAM] = { 0x2c0, BIT(14) },
+ [RST_BUS_EMAC] = { 0x2c0, BIT(17) },
+ [RST_BUS_TS] = { 0x2c0, BIT(18) },
+ [RST_BUS_HSTIMER] = { 0x2c0, BIT(19) },
+ [RST_BUS_SPI0] = { 0x2c0, BIT(20) },
+ [RST_BUS_SPI1] = { 0x2c0, BIT(21) },
+ [RST_BUS_OTG] = { 0x2c0, BIT(23) },
+ [RST_BUS_EHCI0] = { 0x2c0, BIT(24) },
+ [RST_BUS_EHCI1] = { 0x2c0, BIT(25) },
+ [RST_BUS_EHCI2] = { 0x2c0, BIT(26) },
+ [RST_BUS_EHCI3] = { 0x2c0, BIT(27) },
+ [RST_BUS_OHCI0] = { 0x2c0, BIT(28) },
+ [RST_BUS_OHCI1] = { 0x2c0, BIT(29) },
+ [RST_BUS_OHCI2] = { 0x2c0, BIT(30) },
+ [RST_BUS_OHCI3] = { 0x2c0, BIT(31) },
+
+ [RST_BUS_VE] = { 0x2c4, BIT(0) },
+ [RST_BUS_TCON0] = { 0x2c4, BIT(3) },
+ [RST_BUS_TCON1] = { 0x2c4, BIT(4) },
+ [RST_BUS_DEINTERLACE] = { 0x2c4, BIT(5) },
+ [RST_BUS_CSI] = { 0x2c4, BIT(8) },
+ [RST_BUS_TVE] = { 0x2c4, BIT(9) },
+ [RST_BUS_HDMI0] = { 0x2c4, BIT(10) },
+ [RST_BUS_HDMI1] = { 0x2c4, BIT(11) },
+ [RST_BUS_DE] = { 0x2c4, BIT(12) },
+ [RST_BUS_GPU] = { 0x2c4, BIT(20) },
+ [RST_BUS_MSGBOX] = { 0x2c4, BIT(21) },
+ [RST_BUS_SPINLOCK] = { 0x2c4, BIT(22) },
+ [RST_BUS_DBG] = { 0x2c4, BIT(31) },
+
+ [RST_BUS_EPHY] = { 0x2c8, BIT(2) },
+
+ [RST_BUS_CODEC] = { 0x2d0, BIT(0) },
+ [RST_BUS_SPDIF] = { 0x2d0, BIT(1) },
+ [RST_BUS_THS] = { 0x2d0, BIT(8) },
+ [RST_BUS_I2S0] = { 0x2d0, BIT(12) },
+ [RST_BUS_I2S1] = { 0x2d0, BIT(13) },
+ [RST_BUS_I2S2] = { 0x2d0, BIT(14) },
+
+ [RST_BUS_I2C0] = { 0x2d8, BIT(0) },
+ [RST_BUS_I2C1] = { 0x2d8, BIT(1) },
+ [RST_BUS_I2C2] = { 0x2d8, BIT(2) },
+ [RST_BUS_UART0] = { 0x2d8, BIT(16) },
+ [RST_BUS_UART1] = { 0x2d8, BIT(17) },
+ [RST_BUS_UART2] = { 0x2d8, BIT(18) },
+ [RST_BUS_UART3] = { 0x2d8, BIT(19) },
+ [RST_BUS_SCR0] = { 0x2d8, BIT(20) },
};
-static struct ccu_reset_map sunxi_h3_h5_ccu_resets[] = {
+static struct ccu_reset_map sun50i_h5_ccu_resets[] = {
[RST_USB_PHY0] = { 0x0cc, BIT(0) },
[RST_USB_PHY1] = { 0x0cc, BIT(1) },
[RST_USB_PHY2] = { 0x0cc, BIT(2) },
@@ -791,16 +1080,27 @@ static struct ccu_reset_map sunxi_h3_h5_ccu_resets[] = {
[RST_BUS_UART2] = { 0x2d8, BIT(18) },
[RST_BUS_UART3] = { 0x2d8, BIT(19) },
[RST_BUS_SCR0] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR1] = { 0x2d8, BIT(21) },
};
static const struct sunxi_ccu_desc sun8i_h3_ccu_desc = {
- .ccu_clks = sunxi_h3_h5_ccu_clks,
- .num_ccu_clks = ARRAY_SIZE(sunxi_h3_h5_ccu_clks),
+ .ccu_clks = sun8i_h3_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun8i_h3_ccu_clks),
.hw_clks = &sun8i_h3_hw_clks,
- .resets = sunxi_h3_h5_ccu_resets,
- .num_resets = ARRAY_SIZE(sunxi_h3_h5_ccu_resets),
+ .resets = sun8i_h3_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun8i_h3_ccu_resets),
+};
+
+static const struct sunxi_ccu_desc sun50i_h5_ccu_desc = {
+ .ccu_clks = sun50i_h5_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_h5_ccu_clks),
+
+ .hw_clks = &sun50i_h5_hw_clks,
+
+ .resets = sun50i_h5_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_h5_ccu_resets),
};
static struct ccu_mux_nb sunxi_h3_h5_cpu_nb = {
@@ -840,3 +1140,10 @@ static void __init sun8i_h3_ccu_setup(struct device_node *node)
}
CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
sun8i_h3_ccu_setup);
+
+static void __init sun50i_h5_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun50i_h5_ccu_desc);
+}
+CLK_OF_DECLARE(sun50i_h5_ccu, "allwinner,sun50i-h5-ccu",
+ sun50i_h5_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
index e2a4656d2cf3..cc918a00033b 100644
--- a/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
@@ -57,6 +57,7 @@
/* And the GPU module clock is exported */
-#define CLK_NUMBER (CLK_GPU + 1)
+#define CLK_NUMBER_H3 (CLK_GPU + 1)
+#define CLK_NUMBER_H5 (CLK_BUS_SCR1 + 1)
#endif /* _CCU_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/clock/sunxi-h3-h5-ccu.h b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
index 1715a5e12525..4899eacef71d 100644
--- a/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
+++ b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
@@ -142,4 +142,7 @@
#define CLK_GPU 114
+/* New clocks imported in H5 */
+#define CLK_BUS_SCR1 115
+
#endif /* _DT_BINDINGS_CLK_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/reset/sunxi-h3-h5-ccu.h b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
index 7a5de896cf1f..1084c157c062 100644
--- a/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
+++ b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
@@ -100,4 +100,7 @@
#define RST_BUS_UART3 52
#define RST_BUS_SCR0 53
+/* New resets imported in H5 */
+#define RST_BUS_SCR1 54
+
#endif /* _DT_BINDINGS_RST_SUNXI_H3_H5_H_ */
--
2.11.1
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 4/7] ARM: dts: sun8i: convert H3 dtsi to use new sunxi-h3-h5 binding header
2017-02-26 1:19 ` Icenowy Zheng
(?)
@ 2017-02-26 1:19 ` Icenowy Zheng
-1 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
As part of the process that adds H5 support to the original H3 CCU
driver, the device tree binding header changed its name.
Convert the H3 DTSI to use the new binding header.
The only names for H3 changed are {CLK,RST}_BUS_SCR to
{CLK,RST}_BUS_SCR0, not currently used now; so only the header
file's name is changed.
The compatible symlinks are also removed in this commit.
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
Changes in v5:
- Delete transitional headers here.
arch/arm/boot/dts/sun8i-h3.dtsi | 4 ++--
include/dt-bindings/clock/sun8i-h3-ccu.h | 1 -
include/dt-bindings/reset/sun8i-h3-ccu.h | 1 -
3 files changed, 2 insertions(+), 4 deletions(-)
delete mode 120000 include/dt-bindings/clock/sun8i-h3-ccu.h
delete mode 120000 include/dt-bindings/reset/sun8i-h3-ccu.h
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index 27780b97c863..8a4d7894a11f 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -42,10 +42,10 @@
#include "skeleton.dtsi"
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
+#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
+#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
/ {
interrupt-parent = <&gic>;
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
deleted file mode 120000
index ef38232141e4..000000000000
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ /dev/null
@@ -1 +0,0 @@
-sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
deleted file mode 120000
index ef38232141e4..000000000000
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ /dev/null
@@ -1 +0,0 @@
-sunxi-h3-h5-ccu.h
\ No newline at end of file
--
2.11.1
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 4/7] ARM: dts: sun8i: convert H3 dtsi to use new sunxi-h3-h5 binding header
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara
Cc: devicetree, linux-kernel, linux-sunxi, Icenowy Zheng, linux-clk,
linux-arm-kernel
As part of the process that adds H5 support to the original H3 CCU
driver, the device tree binding header changed its name.
Convert the H3 DTSI to use the new binding header.
The only names for H3 changed are {CLK,RST}_BUS_SCR to
{CLK,RST}_BUS_SCR0, not currently used now; so only the header
file's name is changed.
The compatible symlinks are also removed in this commit.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v5:
- Delete transitional headers here.
arch/arm/boot/dts/sun8i-h3.dtsi | 4 ++--
include/dt-bindings/clock/sun8i-h3-ccu.h | 1 -
include/dt-bindings/reset/sun8i-h3-ccu.h | 1 -
3 files changed, 2 insertions(+), 4 deletions(-)
delete mode 120000 include/dt-bindings/clock/sun8i-h3-ccu.h
delete mode 120000 include/dt-bindings/reset/sun8i-h3-ccu.h
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index 27780b97c863..8a4d7894a11f 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -42,10 +42,10 @@
#include "skeleton.dtsi"
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
+#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
+#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
/ {
interrupt-parent = <&gic>;
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
deleted file mode 120000
index ef38232141e4..000000000000
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ /dev/null
@@ -1 +0,0 @@
-sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
deleted file mode 120000
index ef38232141e4..000000000000
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ /dev/null
@@ -1 +0,0 @@
-sunxi-h3-h5-ccu.h
\ No newline at end of file
--
2.11.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 4/7] ARM: dts: sun8i: convert H3 dtsi to use new sunxi-h3-h5 binding header
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: linux-arm-kernel
As part of the process that adds H5 support to the original H3 CCU
driver, the device tree binding header changed its name.
Convert the H3 DTSI to use the new binding header.
The only names for H3 changed are {CLK,RST}_BUS_SCR to
{CLK,RST}_BUS_SCR0, not currently used now; so only the header
file's name is changed.
The compatible symlinks are also removed in this commit.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v5:
- Delete transitional headers here.
arch/arm/boot/dts/sun8i-h3.dtsi | 4 ++--
include/dt-bindings/clock/sun8i-h3-ccu.h | 1 -
include/dt-bindings/reset/sun8i-h3-ccu.h | 1 -
3 files changed, 2 insertions(+), 4 deletions(-)
delete mode 120000 include/dt-bindings/clock/sun8i-h3-ccu.h
delete mode 120000 include/dt-bindings/reset/sun8i-h3-ccu.h
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index 27780b97c863..8a4d7894a11f 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -42,10 +42,10 @@
#include "skeleton.dtsi"
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
+#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
+#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
/ {
interrupt-parent = <&gic>;
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
deleted file mode 120000
index ef38232141e4..000000000000
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ /dev/null
@@ -1 +0,0 @@
-sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
deleted file mode 120000
index ef38232141e4..000000000000
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ /dev/null
@@ -1 +0,0 @@
-sunxi-h3-h5-ccu.h
\ No newline at end of file
--
2.11.1
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 5/7] arm: dts: sun8i: split Allwinner H3 .dtsi
2017-02-26 1:19 ` Icenowy Zheng
(?)
@ 2017-02-26 1:19 ` Icenowy Zheng
-1 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sun8i-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
On the way get rid of skeleton.dtsi, as recommended in that very file.
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
[Icenowy: also split out mmc, as well as pio and ccu's compatible]
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
Changes in v3:
- Use label-based syntax to reference nodes in H3 DTSI file.
Changes in v2:
- Rebase on current linux-next (because of the add of audio codec)
arch/arm/boot/dts/sun8i-h3.dtsi | 789 ++++-----------------
.../boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} | 87 +--
2 files changed, 148 insertions(+), 728 deletions(-)
rewrite arch/arm/boot/dts/sun8i-h3.dtsi (81%)
copy arch/arm/boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} (88%)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
dissimilarity index 81%
index 8a4d7894a11f..4209d974c3f4 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -1,648 +1,141 @@
-/*
- * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include "skeleton.dtsi"
-
-#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
-
-/ {
- interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu@0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- };
-
- cpu@1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <1>;
- };
-
- cpu@2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <2>;
- };
-
- cpu@3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <3>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
-
- clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- osc24M: osc24M_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "osc24M";
- };
-
- osc32k: osc32k_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "osc32k";
- };
-
- apb0: apb0_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "apb0";
- };
-
- apb0_gates: clk@01f01428 {
- compatible = "allwinner,sun8i-h3-apb0-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01f01428 0x4>;
- #clock-cells = <1>;
- clocks = <&apb0>;
- clock-indices = <0>, <1>;
- clock-output-names = "apb0_pio", "apb0_ir";
- };
-
- ir_clk: ir_clk@01f01454 {
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01f01454 0x4>;
- #clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>;
- clock-output-names = "ir";
- };
- };
-
- soc {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- dma: dma-controller@01c02000 {
- compatible = "allwinner,sun8i-h3-dma";
- reg = <0x01c02000 0x1000>;
- interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DMA>;
- resets = <&ccu RST_BUS_DMA>;
- #dma-cells = <1>;
- };
-
- mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC0>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc1: mmc@01c10000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC1>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc2: mmc@01c11000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC2>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- usbphy: phy@01c19400 {
- compatible = "allwinner,sun8i-h3-usb-phy";
- reg = <0x01c19400 0x2c>,
- <0x01c1a800 0x4>,
- <0x01c1b800 0x4>,
- <0x01c1c800 0x4>,
- <0x01c1d800 0x4>;
- reg-names = "phy_ctrl",
- "pmu0",
- "pmu1",
- "pmu2",
- "pmu3";
- clocks = <&ccu CLK_USB_PHY0>,
- <&ccu CLK_USB_PHY1>,
- <&ccu CLK_USB_PHY2>,
- <&ccu CLK_USB_PHY3>;
- clock-names = "usb0_phy",
- "usb1_phy",
- "usb2_phy",
- "usb3_phy";
- resets = <&ccu RST_USB_PHY0>,
- <&ccu RST_USB_PHY1>,
- <&ccu RST_USB_PHY2>,
- <&ccu RST_USB_PHY3>;
- reset-names = "usb0_reset",
- "usb1_reset",
- "usb2_reset",
- "usb3_reset";
- status = "disabled";
- #phy-cells = <1>;
- };
-
- ehci1: usb@01c1b000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1b000 0x100>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci1: usb@01c1b400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1b400 0x100>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
- <&ccu CLK_USB_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci2: usb@01c1c000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1c000 0x100>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci2: usb@01c1c400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1c400 0x100>;
- interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
- <&ccu CLK_USB_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci3: usb@01c1d000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1d000 0x100>;
- interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci3: usb@01c1d400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1d400 0x100>;
- interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
- <&ccu CLK_USB_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ccu: clock@01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
- reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
- clock-names = "hosc", "losc";
- #clock-cells = <1>;
- #reset-cells = <1>;
- };
-
- pio: pinctrl@01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
- reg = <0x01c20800 0x400>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- i2c0_pins: i2c0 {
- pins = "PA11", "PA12";
- function = "i2c0";
- };
-
- i2c1_pins: i2c1 {
- pins = "PA18", "PA19";
- function = "i2c1";
- };
-
- i2c2_pins: i2c2 {
- pins = "PE12", "PE13";
- function = "i2c2";
- };
-
- mmc0_pins_a: mmc0@0 {
- pins = "PF0", "PF1", "PF2", "PF3",
- "PF4", "PF5";
- function = "mmc0";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc0_cd_pin: mmc0_cd_pin@0 {
- pins = "PF6";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc1_pins_a: mmc1@0 {
- pins = "PG0", "PG1", "PG2", "PG3",
- "PG4", "PG5";
- function = "mmc1";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc2_8bit_pins: mmc2_8bit {
- pins = "PC5", "PC6", "PC8",
- "PC9", "PC10", "PC11",
- "PC12", "PC13", "PC14",
- "PC15", "PC16";
- function = "mmc2";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- spdif_tx_pins_a: spdif@0 {
- pins = "PA17";
- function = "spdif";
- };
-
- spi0_pins: spi0 {
- pins = "PC0", "PC1", "PC2", "PC3";
- function = "spi0";
- };
-
- spi1_pins: spi1 {
- pins = "PA15", "PA16", "PA14", "PA13";
- function = "spi1";
- };
-
- uart0_pins_a: uart0@0 {
- pins = "PA4", "PA5";
- function = "uart0";
- };
-
- uart1_pins: uart1 {
- pins = "PG6", "PG7";
- function = "uart1";
- };
-
- uart1_rts_cts_pins: uart1_rts_cts {
- pins = "PG8", "PG9";
- function = "uart1";
- };
-
- uart2_pins: uart2 {
- pins = "PA0", "PA1";
- function = "uart2";
- };
-
- uart3_pins: uart3 {
- pins = "PA13", "PA14";
- function = "uart3";
- };
- };
-
- timer@01c20c00 {
- compatible = "allwinner,sun4i-a10-timer";
- reg = <0x01c20c00 0xa0>;
- interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&osc24M>;
- };
-
- spi0: spi@01c68000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c68000 0x1000>;
- interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
- clock-names = "ahb", "mod";
- dmas = <&dma 23>, <&dma 23>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>;
- resets = <&ccu RST_BUS_SPI0>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- spi1: spi@01c69000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c69000 0x1000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
- clock-names = "ahb", "mod";
- dmas = <&dma 24>, <&dma 24>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins>;
- resets = <&ccu RST_BUS_SPI1>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- wdt0: watchdog@01c20ca0 {
- compatible = "allwinner,sun6i-a31-wdt";
- reg = <0x01c20ca0 0x20>;
- interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- spdif: spdif@01c21000 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-spdif";
- reg = <0x01c21000 0x400>;
- interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
- resets = <&ccu RST_BUS_SPDIF>;
- clock-names = "apb", "spdif";
- dmas = <&dma 2>;
- dma-names = "tx";
- status = "disabled";
- };
-
- pwm: pwm@01c21400 {
- compatible = "allwinner,sun8i-h3-pwm";
- reg = <0x01c21400 0x8>;
- clocks = <&osc24M>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- codec: codec@01c22c00 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-codec";
- reg = <0x01c22c00 0x400>;
- interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
- clock-names = "apb", "codec";
- resets = <&ccu RST_BUS_CODEC>;
- dmas = <&dma 15>, <&dma 15>;
- dma-names = "rx", "tx";
- allwinner,codec-analog-controls = <&codec_analog>;
- status = "disabled";
- };
-
- uart0: serial@01c28000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28000 0x400>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART0>;
- resets = <&ccu RST_BUS_UART0>;
- dmas = <&dma 6>, <&dma 6>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart1: serial@01c28400 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28400 0x400>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART1>;
- resets = <&ccu RST_BUS_UART1>;
- dmas = <&dma 7>, <&dma 7>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart2: serial@01c28800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28800 0x400>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART2>;
- resets = <&ccu RST_BUS_UART2>;
- dmas = <&dma 8>, <&dma 8>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart3: serial@01c28c00 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28c00 0x400>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART3>;
- resets = <&ccu RST_BUS_UART3>;
- dmas = <&dma 9>, <&dma 9>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- i2c0: i2c@01c2ac00 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2ac00 0x400>;
- interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C0>;
- resets = <&ccu RST_BUS_I2C0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c1: i2c@01c2b000 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C1>;
- resets = <&ccu RST_BUS_I2C1>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c2: i2c@01c2b400 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C2>;
- resets = <&ccu RST_BUS_I2C2>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- gic: interrupt-controller@01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
- reg = <0x01c81000 0x1000>,
- <0x01c82000 0x2000>,
- <0x01c84000 0x2000>,
- <0x01c86000 0x2000>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- };
-
- rtc: rtc@01f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x54>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- apb0_reset: reset@01f014b0 {
- reg = <0x01f014b0 0x4>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- #reset-cells = <1>;
- };
-
- codec_analog: codec-analog@01f015c0 {
- compatible = "allwinner,sun8i-h3-codec-analog";
- reg = <0x01f015c0 0x4>;
- };
-
- ir: ir@01f02000 {
- compatible = "allwinner,sun5i-a13-ir";
- clocks = <&apb0_gates 1>, <&ir_clk>;
- clock-names = "apb", "ir";
- resets = <&apb0_reset 1>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x01f02000 0x40>;
- status = "disabled";
- };
-
- r_pio: pinctrl@01f02c00 {
- compatible = "allwinner,sun8i-h3-r-pinctrl";
- reg = <0x01f02c00 0x400>;
- interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- resets = <&apb0_reset 0>;
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- ir_pins_a: ir@0 {
- pins = "PL11";
- function = "s_cir_rx";
- };
- };
- };
-};
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <2>;
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <3>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ gic: interrupt-controller@01c81000 {
+ compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x2000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+ };
+};
+
+&ccu {
+ compatible = "allwinner,sun8i-h3-ccu";
+};
+
+&mmc0 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>,
+ <&ccu CLK_MMC0>,
+ <&ccu CLK_MMC0_OUTPUT>,
+ <&ccu CLK_MMC0_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&mmc1 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>,
+ <&ccu CLK_MMC1>,
+ <&ccu CLK_MMC1_OUTPUT>,
+ <&ccu CLK_MMC1_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&mmc2 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC2>,
+ <&ccu CLK_MMC2>,
+ <&ccu CLK_MMC2_OUTPUT>,
+ <&ccu CLK_MMC2_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&pio {
+ compatible = "allwinner,sun8i-h3-pinctrl";
+};
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
similarity index 88%
copy from arch/arm/boot/dts/sun8i-h3.dtsi
copy to arch/arm/boot/dts/sunxi-h3-h5.dtsi
index 8a4d7894a11f..966dc4211c4d 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -40,52 +40,14 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
/ {
- interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu@0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- };
-
- cpu@1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <1>;
- };
-
- cpu@2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <2>;
- };
-
- cpu@3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <3>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
+ #address-cells = <1>;
+ #size-cells = <1>;
clocks {
#address-cells = <1>;
@@ -150,16 +112,8 @@
};
mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
@@ -169,16 +123,8 @@
};
mmc1: mmc@01c10000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC1>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
@@ -188,16 +134,8 @@
};
mmc2: mmc@01c11000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC2>;
reset-names = "ahb";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
@@ -308,7 +246,7 @@
};
ccu: clock@01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
+ /* compatible is in per SoC .dtsi file */
reg = <0x01c20000 0x400>;
clocks = <&osc24M>, <&osc32k>;
clock-names = "hosc", "losc";
@@ -317,7 +255,7 @@
};
pio: pinctrl@01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
+ /* compatible is in per SoC .dtsi file */
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
@@ -588,17 +526,6 @@
#size-cells = <0>;
};
- gic: interrupt-controller@01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
- reg = <0x01c81000 0x1000>,
- <0x01c82000 0x2000>,
- <0x01c84000 0x2000>,
- <0x01c86000 0x2000>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- };
-
rtc: rtc@01f00000 {
compatible = "allwinner,sun6i-a31-rtc";
reg = <0x01f00000 0x54>;
--
2.11.1
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 5/7] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara
Cc: devicetree, linux-kernel, linux-sunxi, Icenowy Zheng, linux-clk,
linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sun8i-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
On the way get rid of skeleton.dtsi, as recommended in that very file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: also split out mmc, as well as pio and ccu's compatible]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v3:
- Use label-based syntax to reference nodes in H3 DTSI file.
Changes in v2:
- Rebase on current linux-next (because of the add of audio codec)
arch/arm/boot/dts/sun8i-h3.dtsi | 789 ++++-----------------
.../boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} | 87 +--
2 files changed, 148 insertions(+), 728 deletions(-)
rewrite arch/arm/boot/dts/sun8i-h3.dtsi (81%)
copy arch/arm/boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} (88%)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
dissimilarity index 81%
index 8a4d7894a11f..4209d974c3f4 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -1,648 +1,141 @@
-/*
- * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include "skeleton.dtsi"
-
-#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
-
-/ {
- interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu@0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- };
-
- cpu@1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <1>;
- };
-
- cpu@2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <2>;
- };
-
- cpu@3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <3>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
-
- clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- osc24M: osc24M_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "osc24M";
- };
-
- osc32k: osc32k_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "osc32k";
- };
-
- apb0: apb0_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "apb0";
- };
-
- apb0_gates: clk@01f01428 {
- compatible = "allwinner,sun8i-h3-apb0-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01f01428 0x4>;
- #clock-cells = <1>;
- clocks = <&apb0>;
- clock-indices = <0>, <1>;
- clock-output-names = "apb0_pio", "apb0_ir";
- };
-
- ir_clk: ir_clk@01f01454 {
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01f01454 0x4>;
- #clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>;
- clock-output-names = "ir";
- };
- };
-
- soc {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- dma: dma-controller@01c02000 {
- compatible = "allwinner,sun8i-h3-dma";
- reg = <0x01c02000 0x1000>;
- interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DMA>;
- resets = <&ccu RST_BUS_DMA>;
- #dma-cells = <1>;
- };
-
- mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC0>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc1: mmc@01c10000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC1>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc2: mmc@01c11000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC2>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- usbphy: phy@01c19400 {
- compatible = "allwinner,sun8i-h3-usb-phy";
- reg = <0x01c19400 0x2c>,
- <0x01c1a800 0x4>,
- <0x01c1b800 0x4>,
- <0x01c1c800 0x4>,
- <0x01c1d800 0x4>;
- reg-names = "phy_ctrl",
- "pmu0",
- "pmu1",
- "pmu2",
- "pmu3";
- clocks = <&ccu CLK_USB_PHY0>,
- <&ccu CLK_USB_PHY1>,
- <&ccu CLK_USB_PHY2>,
- <&ccu CLK_USB_PHY3>;
- clock-names = "usb0_phy",
- "usb1_phy",
- "usb2_phy",
- "usb3_phy";
- resets = <&ccu RST_USB_PHY0>,
- <&ccu RST_USB_PHY1>,
- <&ccu RST_USB_PHY2>,
- <&ccu RST_USB_PHY3>;
- reset-names = "usb0_reset",
- "usb1_reset",
- "usb2_reset",
- "usb3_reset";
- status = "disabled";
- #phy-cells = <1>;
- };
-
- ehci1: usb@01c1b000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1b000 0x100>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci1: usb@01c1b400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1b400 0x100>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
- <&ccu CLK_USB_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci2: usb@01c1c000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1c000 0x100>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci2: usb@01c1c400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1c400 0x100>;
- interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
- <&ccu CLK_USB_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci3: usb@01c1d000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1d000 0x100>;
- interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci3: usb@01c1d400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1d400 0x100>;
- interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
- <&ccu CLK_USB_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ccu: clock@01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
- reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
- clock-names = "hosc", "losc";
- #clock-cells = <1>;
- #reset-cells = <1>;
- };
-
- pio: pinctrl@01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
- reg = <0x01c20800 0x400>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- i2c0_pins: i2c0 {
- pins = "PA11", "PA12";
- function = "i2c0";
- };
-
- i2c1_pins: i2c1 {
- pins = "PA18", "PA19";
- function = "i2c1";
- };
-
- i2c2_pins: i2c2 {
- pins = "PE12", "PE13";
- function = "i2c2";
- };
-
- mmc0_pins_a: mmc0@0 {
- pins = "PF0", "PF1", "PF2", "PF3",
- "PF4", "PF5";
- function = "mmc0";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc0_cd_pin: mmc0_cd_pin@0 {
- pins = "PF6";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc1_pins_a: mmc1@0 {
- pins = "PG0", "PG1", "PG2", "PG3",
- "PG4", "PG5";
- function = "mmc1";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc2_8bit_pins: mmc2_8bit {
- pins = "PC5", "PC6", "PC8",
- "PC9", "PC10", "PC11",
- "PC12", "PC13", "PC14",
- "PC15", "PC16";
- function = "mmc2";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- spdif_tx_pins_a: spdif@0 {
- pins = "PA17";
- function = "spdif";
- };
-
- spi0_pins: spi0 {
- pins = "PC0", "PC1", "PC2", "PC3";
- function = "spi0";
- };
-
- spi1_pins: spi1 {
- pins = "PA15", "PA16", "PA14", "PA13";
- function = "spi1";
- };
-
- uart0_pins_a: uart0@0 {
- pins = "PA4", "PA5";
- function = "uart0";
- };
-
- uart1_pins: uart1 {
- pins = "PG6", "PG7";
- function = "uart1";
- };
-
- uart1_rts_cts_pins: uart1_rts_cts {
- pins = "PG8", "PG9";
- function = "uart1";
- };
-
- uart2_pins: uart2 {
- pins = "PA0", "PA1";
- function = "uart2";
- };
-
- uart3_pins: uart3 {
- pins = "PA13", "PA14";
- function = "uart3";
- };
- };
-
- timer@01c20c00 {
- compatible = "allwinner,sun4i-a10-timer";
- reg = <0x01c20c00 0xa0>;
- interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&osc24M>;
- };
-
- spi0: spi@01c68000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c68000 0x1000>;
- interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
- clock-names = "ahb", "mod";
- dmas = <&dma 23>, <&dma 23>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>;
- resets = <&ccu RST_BUS_SPI0>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- spi1: spi@01c69000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c69000 0x1000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
- clock-names = "ahb", "mod";
- dmas = <&dma 24>, <&dma 24>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins>;
- resets = <&ccu RST_BUS_SPI1>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- wdt0: watchdog@01c20ca0 {
- compatible = "allwinner,sun6i-a31-wdt";
- reg = <0x01c20ca0 0x20>;
- interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- spdif: spdif@01c21000 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-spdif";
- reg = <0x01c21000 0x400>;
- interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
- resets = <&ccu RST_BUS_SPDIF>;
- clock-names = "apb", "spdif";
- dmas = <&dma 2>;
- dma-names = "tx";
- status = "disabled";
- };
-
- pwm: pwm@01c21400 {
- compatible = "allwinner,sun8i-h3-pwm";
- reg = <0x01c21400 0x8>;
- clocks = <&osc24M>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- codec: codec@01c22c00 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-codec";
- reg = <0x01c22c00 0x400>;
- interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
- clock-names = "apb", "codec";
- resets = <&ccu RST_BUS_CODEC>;
- dmas = <&dma 15>, <&dma 15>;
- dma-names = "rx", "tx";
- allwinner,codec-analog-controls = <&codec_analog>;
- status = "disabled";
- };
-
- uart0: serial@01c28000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28000 0x400>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART0>;
- resets = <&ccu RST_BUS_UART0>;
- dmas = <&dma 6>, <&dma 6>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart1: serial@01c28400 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28400 0x400>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART1>;
- resets = <&ccu RST_BUS_UART1>;
- dmas = <&dma 7>, <&dma 7>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart2: serial@01c28800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28800 0x400>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART2>;
- resets = <&ccu RST_BUS_UART2>;
- dmas = <&dma 8>, <&dma 8>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart3: serial@01c28c00 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28c00 0x400>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART3>;
- resets = <&ccu RST_BUS_UART3>;
- dmas = <&dma 9>, <&dma 9>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- i2c0: i2c@01c2ac00 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2ac00 0x400>;
- interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C0>;
- resets = <&ccu RST_BUS_I2C0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c1: i2c@01c2b000 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C1>;
- resets = <&ccu RST_BUS_I2C1>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c2: i2c@01c2b400 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C2>;
- resets = <&ccu RST_BUS_I2C2>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- gic: interrupt-controller@01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
- reg = <0x01c81000 0x1000>,
- <0x01c82000 0x2000>,
- <0x01c84000 0x2000>,
- <0x01c86000 0x2000>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- };
-
- rtc: rtc@01f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x54>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- apb0_reset: reset@01f014b0 {
- reg = <0x01f014b0 0x4>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- #reset-cells = <1>;
- };
-
- codec_analog: codec-analog@01f015c0 {
- compatible = "allwinner,sun8i-h3-codec-analog";
- reg = <0x01f015c0 0x4>;
- };
-
- ir: ir@01f02000 {
- compatible = "allwinner,sun5i-a13-ir";
- clocks = <&apb0_gates 1>, <&ir_clk>;
- clock-names = "apb", "ir";
- resets = <&apb0_reset 1>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x01f02000 0x40>;
- status = "disabled";
- };
-
- r_pio: pinctrl@01f02c00 {
- compatible = "allwinner,sun8i-h3-r-pinctrl";
- reg = <0x01f02c00 0x400>;
- interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- resets = <&apb0_reset 0>;
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- ir_pins_a: ir@0 {
- pins = "PL11";
- function = "s_cir_rx";
- };
- };
- };
-};
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <2>;
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <3>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ gic: interrupt-controller@01c81000 {
+ compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x2000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+ };
+};
+
+&ccu {
+ compatible = "allwinner,sun8i-h3-ccu";
+};
+
+&mmc0 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>,
+ <&ccu CLK_MMC0>,
+ <&ccu CLK_MMC0_OUTPUT>,
+ <&ccu CLK_MMC0_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&mmc1 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>,
+ <&ccu CLK_MMC1>,
+ <&ccu CLK_MMC1_OUTPUT>,
+ <&ccu CLK_MMC1_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&mmc2 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC2>,
+ <&ccu CLK_MMC2>,
+ <&ccu CLK_MMC2_OUTPUT>,
+ <&ccu CLK_MMC2_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&pio {
+ compatible = "allwinner,sun8i-h3-pinctrl";
+};
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
similarity index 88%
copy from arch/arm/boot/dts/sun8i-h3.dtsi
copy to arch/arm/boot/dts/sunxi-h3-h5.dtsi
index 8a4d7894a11f..966dc4211c4d 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -40,52 +40,14 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
/ {
- interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu@0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- };
-
- cpu@1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <1>;
- };
-
- cpu@2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <2>;
- };
-
- cpu@3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <3>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
+ #address-cells = <1>;
+ #size-cells = <1>;
clocks {
#address-cells = <1>;
@@ -150,16 +112,8 @@
};
mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
@@ -169,16 +123,8 @@
};
mmc1: mmc@01c10000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC1>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
@@ -188,16 +134,8 @@
};
mmc2: mmc@01c11000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC2>;
reset-names = "ahb";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
@@ -308,7 +246,7 @@
};
ccu: clock@01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
+ /* compatible is in per SoC .dtsi file */
reg = <0x01c20000 0x400>;
clocks = <&osc24M>, <&osc32k>;
clock-names = "hosc", "losc";
@@ -317,7 +255,7 @@
};
pio: pinctrl@01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
+ /* compatible is in per SoC .dtsi file */
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
@@ -588,17 +526,6 @@
#size-cells = <0>;
};
- gic: interrupt-controller@01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
- reg = <0x01c81000 0x1000>,
- <0x01c82000 0x2000>,
- <0x01c84000 0x2000>,
- <0x01c86000 0x2000>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- };
-
rtc: rtc@01f00000 {
compatible = "allwinner,sun6i-a31-rtc";
reg = <0x01f00000 0x54>;
--
2.11.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 5/7] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sun8i-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
On the way get rid of skeleton.dtsi, as recommended in that very file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: also split out mmc, as well as pio and ccu's compatible]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v3:
- Use label-based syntax to reference nodes in H3 DTSI file.
Changes in v2:
- Rebase on current linux-next (because of the add of audio codec)
arch/arm/boot/dts/sun8i-h3.dtsi | 789 ++++-----------------
.../boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} | 87 +--
2 files changed, 148 insertions(+), 728 deletions(-)
rewrite arch/arm/boot/dts/sun8i-h3.dtsi (81%)
copy arch/arm/boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} (88%)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
dissimilarity index 81%
index 8a4d7894a11f..4209d974c3f4 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -1,648 +1,141 @@
-/*
- * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include "skeleton.dtsi"
-
-#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
-
-/ {
- interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu at 0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- };
-
- cpu at 1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <1>;
- };
-
- cpu at 2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <2>;
- };
-
- cpu at 3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <3>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
-
- clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- osc24M: osc24M_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "osc24M";
- };
-
- osc32k: osc32k_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "osc32k";
- };
-
- apb0: apb0_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "apb0";
- };
-
- apb0_gates: clk at 01f01428 {
- compatible = "allwinner,sun8i-h3-apb0-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01f01428 0x4>;
- #clock-cells = <1>;
- clocks = <&apb0>;
- clock-indices = <0>, <1>;
- clock-output-names = "apb0_pio", "apb0_ir";
- };
-
- ir_clk: ir_clk at 01f01454 {
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01f01454 0x4>;
- #clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>;
- clock-output-names = "ir";
- };
- };
-
- soc {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- dma: dma-controller at 01c02000 {
- compatible = "allwinner,sun8i-h3-dma";
- reg = <0x01c02000 0x1000>;
- interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DMA>;
- resets = <&ccu RST_BUS_DMA>;
- #dma-cells = <1>;
- };
-
- mmc0: mmc at 01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC0>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc1: mmc at 01c10000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC1>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc2: mmc at 01c11000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC2>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- usbphy: phy at 01c19400 {
- compatible = "allwinner,sun8i-h3-usb-phy";
- reg = <0x01c19400 0x2c>,
- <0x01c1a800 0x4>,
- <0x01c1b800 0x4>,
- <0x01c1c800 0x4>,
- <0x01c1d800 0x4>;
- reg-names = "phy_ctrl",
- "pmu0",
- "pmu1",
- "pmu2",
- "pmu3";
- clocks = <&ccu CLK_USB_PHY0>,
- <&ccu CLK_USB_PHY1>,
- <&ccu CLK_USB_PHY2>,
- <&ccu CLK_USB_PHY3>;
- clock-names = "usb0_phy",
- "usb1_phy",
- "usb2_phy",
- "usb3_phy";
- resets = <&ccu RST_USB_PHY0>,
- <&ccu RST_USB_PHY1>,
- <&ccu RST_USB_PHY2>,
- <&ccu RST_USB_PHY3>;
- reset-names = "usb0_reset",
- "usb1_reset",
- "usb2_reset",
- "usb3_reset";
- status = "disabled";
- #phy-cells = <1>;
- };
-
- ehci1: usb at 01c1b000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1b000 0x100>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci1: usb at 01c1b400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1b400 0x100>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
- <&ccu CLK_USB_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci2: usb at 01c1c000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1c000 0x100>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci2: usb at 01c1c400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1c400 0x100>;
- interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
- <&ccu CLK_USB_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci3: usb at 01c1d000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1d000 0x100>;
- interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci3: usb at 01c1d400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1d400 0x100>;
- interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
- <&ccu CLK_USB_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ccu: clock at 01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
- reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
- clock-names = "hosc", "losc";
- #clock-cells = <1>;
- #reset-cells = <1>;
- };
-
- pio: pinctrl at 01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
- reg = <0x01c20800 0x400>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- i2c0_pins: i2c0 {
- pins = "PA11", "PA12";
- function = "i2c0";
- };
-
- i2c1_pins: i2c1 {
- pins = "PA18", "PA19";
- function = "i2c1";
- };
-
- i2c2_pins: i2c2 {
- pins = "PE12", "PE13";
- function = "i2c2";
- };
-
- mmc0_pins_a: mmc0 at 0 {
- pins = "PF0", "PF1", "PF2", "PF3",
- "PF4", "PF5";
- function = "mmc0";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc0_cd_pin: mmc0_cd_pin at 0 {
- pins = "PF6";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc1_pins_a: mmc1 at 0 {
- pins = "PG0", "PG1", "PG2", "PG3",
- "PG4", "PG5";
- function = "mmc1";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc2_8bit_pins: mmc2_8bit {
- pins = "PC5", "PC6", "PC8",
- "PC9", "PC10", "PC11",
- "PC12", "PC13", "PC14",
- "PC15", "PC16";
- function = "mmc2";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- spdif_tx_pins_a: spdif at 0 {
- pins = "PA17";
- function = "spdif";
- };
-
- spi0_pins: spi0 {
- pins = "PC0", "PC1", "PC2", "PC3";
- function = "spi0";
- };
-
- spi1_pins: spi1 {
- pins = "PA15", "PA16", "PA14", "PA13";
- function = "spi1";
- };
-
- uart0_pins_a: uart0 at 0 {
- pins = "PA4", "PA5";
- function = "uart0";
- };
-
- uart1_pins: uart1 {
- pins = "PG6", "PG7";
- function = "uart1";
- };
-
- uart1_rts_cts_pins: uart1_rts_cts {
- pins = "PG8", "PG9";
- function = "uart1";
- };
-
- uart2_pins: uart2 {
- pins = "PA0", "PA1";
- function = "uart2";
- };
-
- uart3_pins: uart3 {
- pins = "PA13", "PA14";
- function = "uart3";
- };
- };
-
- timer at 01c20c00 {
- compatible = "allwinner,sun4i-a10-timer";
- reg = <0x01c20c00 0xa0>;
- interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&osc24M>;
- };
-
- spi0: spi at 01c68000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c68000 0x1000>;
- interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
- clock-names = "ahb", "mod";
- dmas = <&dma 23>, <&dma 23>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>;
- resets = <&ccu RST_BUS_SPI0>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- spi1: spi at 01c69000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c69000 0x1000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
- clock-names = "ahb", "mod";
- dmas = <&dma 24>, <&dma 24>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins>;
- resets = <&ccu RST_BUS_SPI1>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- wdt0: watchdog at 01c20ca0 {
- compatible = "allwinner,sun6i-a31-wdt";
- reg = <0x01c20ca0 0x20>;
- interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- spdif: spdif at 01c21000 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-spdif";
- reg = <0x01c21000 0x400>;
- interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
- resets = <&ccu RST_BUS_SPDIF>;
- clock-names = "apb", "spdif";
- dmas = <&dma 2>;
- dma-names = "tx";
- status = "disabled";
- };
-
- pwm: pwm at 01c21400 {
- compatible = "allwinner,sun8i-h3-pwm";
- reg = <0x01c21400 0x8>;
- clocks = <&osc24M>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- codec: codec at 01c22c00 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-codec";
- reg = <0x01c22c00 0x400>;
- interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
- clock-names = "apb", "codec";
- resets = <&ccu RST_BUS_CODEC>;
- dmas = <&dma 15>, <&dma 15>;
- dma-names = "rx", "tx";
- allwinner,codec-analog-controls = <&codec_analog>;
- status = "disabled";
- };
-
- uart0: serial at 01c28000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28000 0x400>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART0>;
- resets = <&ccu RST_BUS_UART0>;
- dmas = <&dma 6>, <&dma 6>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart1: serial at 01c28400 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28400 0x400>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART1>;
- resets = <&ccu RST_BUS_UART1>;
- dmas = <&dma 7>, <&dma 7>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart2: serial at 01c28800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28800 0x400>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART2>;
- resets = <&ccu RST_BUS_UART2>;
- dmas = <&dma 8>, <&dma 8>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart3: serial at 01c28c00 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28c00 0x400>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART3>;
- resets = <&ccu RST_BUS_UART3>;
- dmas = <&dma 9>, <&dma 9>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- i2c0: i2c at 01c2ac00 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2ac00 0x400>;
- interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C0>;
- resets = <&ccu RST_BUS_I2C0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c1: i2c at 01c2b000 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C1>;
- resets = <&ccu RST_BUS_I2C1>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c2: i2c at 01c2b400 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C2>;
- resets = <&ccu RST_BUS_I2C2>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- gic: interrupt-controller at 01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
- reg = <0x01c81000 0x1000>,
- <0x01c82000 0x2000>,
- <0x01c84000 0x2000>,
- <0x01c86000 0x2000>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- };
-
- rtc: rtc at 01f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x54>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- apb0_reset: reset at 01f014b0 {
- reg = <0x01f014b0 0x4>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- #reset-cells = <1>;
- };
-
- codec_analog: codec-analog at 01f015c0 {
- compatible = "allwinner,sun8i-h3-codec-analog";
- reg = <0x01f015c0 0x4>;
- };
-
- ir: ir at 01f02000 {
- compatible = "allwinner,sun5i-a13-ir";
- clocks = <&apb0_gates 1>, <&ir_clk>;
- clock-names = "apb", "ir";
- resets = <&apb0_reset 1>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x01f02000 0x40>;
- status = "disabled";
- };
-
- r_pio: pinctrl at 01f02c00 {
- compatible = "allwinner,sun8i-h3-r-pinctrl";
- reg = <0x01f02c00 0x400>;
- interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- resets = <&apb0_reset 0>;
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- ir_pins_a: ir at 0 {
- pins = "PL11";
- function = "s_cir_rx";
- };
- };
- };
-};
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu at 1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+
+ cpu at 2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <2>;
+ };
+
+ cpu at 3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <3>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ gic: interrupt-controller at 01c81000 {
+ compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x2000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+ };
+};
+
+&ccu {
+ compatible = "allwinner,sun8i-h3-ccu";
+};
+
+&mmc0 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>,
+ <&ccu CLK_MMC0>,
+ <&ccu CLK_MMC0_OUTPUT>,
+ <&ccu CLK_MMC0_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&mmc1 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>,
+ <&ccu CLK_MMC1>,
+ <&ccu CLK_MMC1_OUTPUT>,
+ <&ccu CLK_MMC1_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&mmc2 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC2>,
+ <&ccu CLK_MMC2>,
+ <&ccu CLK_MMC2_OUTPUT>,
+ <&ccu CLK_MMC2_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&pio {
+ compatible = "allwinner,sun8i-h3-pinctrl";
+};
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
similarity index 88%
copy from arch/arm/boot/dts/sun8i-h3.dtsi
copy to arch/arm/boot/dts/sunxi-h3-h5.dtsi
index 8a4d7894a11f..966dc4211c4d 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -40,52 +40,14 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
/ {
- interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu at 0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- };
-
- cpu at 1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <1>;
- };
-
- cpu at 2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <2>;
- };
-
- cpu at 3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <3>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
+ #address-cells = <1>;
+ #size-cells = <1>;
clocks {
#address-cells = <1>;
@@ -150,16 +112,8 @@
};
mmc0: mmc at 01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
@@ -169,16 +123,8 @@
};
mmc1: mmc at 01c10000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC1>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
@@ -188,16 +134,8 @@
};
mmc2: mmc at 01c11000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC2>;
reset-names = "ahb";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
@@ -308,7 +246,7 @@
};
ccu: clock at 01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
+ /* compatible is in per SoC .dtsi file */
reg = <0x01c20000 0x400>;
clocks = <&osc24M>, <&osc32k>;
clock-names = "hosc", "losc";
@@ -317,7 +255,7 @@
};
pio: pinctrl at 01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
+ /* compatible is in per SoC .dtsi file */
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
@@ -588,17 +526,6 @@
#size-cells = <0>;
};
- gic: interrupt-controller at 01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
- reg = <0x01c81000 0x1000>,
- <0x01c82000 0x2000>,
- <0x01c84000 0x2000>,
- <0x01c86000 0x2000>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- };
-
rtc: rtc at 01f00000 {
compatible = "allwinner,sun6i-a31-rtc";
reg = <0x01f00000 0x54>;
--
2.11.1
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 6/7] arm64: dts: allwinner: add Allwinner H5 .dtsi
2017-02-26 1:19 ` Icenowy Zheng
(?)
@ 2017-02-26 1:19 ` Icenowy Zheng
-1 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
[Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
refactor, commit message change to met new arm64 naming scheme,
drop H3 pinctrl compatible because of interrupt bank change, drop
H3 ccu compatible because of clock change]
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
Changes in v3:
- Dropped sun5i-a13-mmc, sun8i-h3-ccu compatibles.
- Used sun50i-{h5,a64}-emmc compatible for mmc2.
Changes in v2:
- Dropped sun8i-h3-pinctrl compatible, as the interrupt of H3 and H5 is
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 139 +++++++++++++++++++++++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
2 files changed, 140 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
new file mode 100644
index 000000000000..b651bd6986e8
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -0,0 +1,139 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0>;
+ enable-method = "psci";
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <1>;
+ enable-method = "psci";
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <2>;
+ enable-method = "psci";
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <3>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ gic: interrupt-controller@1c81000 {
+ compatible = "arm,gic-400";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x2000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+ };
+};
+
+&ccu {
+ compatible = "allwinner,sun50i-h5-ccu";
+};
+
+&mmc0 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+};
+
+&mmc1 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+};
+
+&mmc2 {
+ compatible = "allwinner,sun50i-h5-emmc",
+ "allwinner,sun50i-a64-emmc";
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+};
+
+&pio {
+ compatible = "allwinner,sun50i-h5-pinctrl";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
new file mode 120000
index 000000000000..036f01dc2b9b
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
@@ -0,0 +1 @@
+../../../../arm/boot/dts/sunxi-h3-h5.dtsi
\ No newline at end of file
--
2.11.1
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 6/7] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara
Cc: devicetree, linux-kernel, linux-sunxi, Icenowy Zheng, linux-clk,
linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
refactor, commit message change to met new arm64 naming scheme,
drop H3 pinctrl compatible because of interrupt bank change, drop
H3 ccu compatible because of clock change]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v3:
- Dropped sun5i-a13-mmc, sun8i-h3-ccu compatibles.
- Used sun50i-{h5,a64}-emmc compatible for mmc2.
Changes in v2:
- Dropped sun8i-h3-pinctrl compatible, as the interrupt of H3 and H5 is
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 139 +++++++++++++++++++++++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
2 files changed, 140 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
new file mode 100644
index 000000000000..b651bd6986e8
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -0,0 +1,139 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0>;
+ enable-method = "psci";
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <1>;
+ enable-method = "psci";
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <2>;
+ enable-method = "psci";
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <3>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ gic: interrupt-controller@1c81000 {
+ compatible = "arm,gic-400";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x2000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+ };
+};
+
+&ccu {
+ compatible = "allwinner,sun50i-h5-ccu";
+};
+
+&mmc0 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+};
+
+&mmc1 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+};
+
+&mmc2 {
+ compatible = "allwinner,sun50i-h5-emmc",
+ "allwinner,sun50i-a64-emmc";
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+};
+
+&pio {
+ compatible = "allwinner,sun50i-h5-pinctrl";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
new file mode 120000
index 000000000000..036f01dc2b9b
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
@@ -0,0 +1 @@
+../../../../arm/boot/dts/sunxi-h3-h5.dtsi
\ No newline at end of file
--
2.11.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 6/7] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
refactor, commit message change to met new arm64 naming scheme,
drop H3 pinctrl compatible because of interrupt bank change, drop
H3 ccu compatible because of clock change]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v3:
- Dropped sun5i-a13-mmc, sun8i-h3-ccu compatibles.
- Used sun50i-{h5,a64}-emmc compatible for mmc2.
Changes in v2:
- Dropped sun8i-h3-pinctrl compatible, as the interrupt of H3 and H5 is
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 139 +++++++++++++++++++++++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
2 files changed, 140 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
new file mode 100644
index 000000000000..b651bd6986e8
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -0,0 +1,139 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0>;
+ enable-method = "psci";
+ };
+
+ cpu at 1 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <1>;
+ enable-method = "psci";
+ };
+
+ cpu at 2 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <2>;
+ enable-method = "psci";
+ };
+
+ cpu at 3 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <3>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ gic: interrupt-controller at 1c81000 {
+ compatible = "arm,gic-400";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x2000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+ };
+};
+
+&ccu {
+ compatible = "allwinner,sun50i-h5-ccu";
+};
+
+&mmc0 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+};
+
+&mmc1 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+};
+
+&mmc2 {
+ compatible = "allwinner,sun50i-h5-emmc",
+ "allwinner,sun50i-a64-emmc";
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+};
+
+&pio {
+ compatible = "allwinner,sun50i-h5-pinctrl";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
new file mode 120000
index 000000000000..036f01dc2b9b
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
@@ -0,0 +1 @@
+../../../../arm/boot/dts/sunxi-h3-h5.dtsi
\ No newline at end of file
--
2.11.1
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 7/7] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
2017-02-26 1:19 ` Icenowy Zheng
(?)
@ 2017-02-26 1:19 ` Icenowy Zheng
-1 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio]
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
Changes in v2:
- Dropped all GPIO pinctrl nodes.
- Changed red LED gpio to the correct one.
- Added audio codec configuration copied from Orange Pi PC.
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 164 +++++++++++++++++++++
2 files changed, 165 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index bc6f342be59f..244e8b7565f9 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -1,5 +1,6 @@
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
new file mode 100644
index 000000000000..79784cba806c
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
@@ -0,0 +1,164 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi PC 2";
+ compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5";
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr_led {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status_led {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usbphy {
+ /* USB VBUS is always on */
+ status = "okay";
+};
--
2.11.1
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 7/7] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara
Cc: devicetree, linux-kernel, linux-sunxi, Icenowy Zheng, linux-clk,
linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v2:
- Dropped all GPIO pinctrl nodes.
- Changed red LED gpio to the correct one.
- Added audio codec configuration copied from Orange Pi PC.
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 164 +++++++++++++++++++++
2 files changed, 165 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index bc6f342be59f..244e8b7565f9 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -1,5 +1,6 @@
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
new file mode 100644
index 000000000000..79784cba806c
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
@@ -0,0 +1,164 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi PC 2";
+ compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5";
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr_led {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status_led {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usbphy {
+ /* USB VBUS is always on */
+ status = "okay";
+};
--
2.11.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 62+ messages in thread
* [PATCH v5 7/7] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
@ 2017-02-26 1:19 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 1:19 UTC (permalink / raw)
To: linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v2:
- Dropped all GPIO pinctrl nodes.
- Changed red LED gpio to the correct one.
- Added audio codec configuration copied from Orange Pi PC.
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 164 +++++++++++++++++++++
2 files changed, 165 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index bc6f342be59f..244e8b7565f9 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -1,5 +1,6 @@
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
new file mode 100644
index 000000000000..79784cba806c
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
@@ -0,0 +1,164 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi PC 2";
+ compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5";
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr_led {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status_led {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usbphy {
+ /* USB VBUS is always on */
+ status = "okay";
+};
--
2.11.1
^ permalink raw reply related [flat|nested] 62+ messages in thread
* Re: [PATCH v5 5/7] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-02-26 3:46 ` Chen-Yu Tsai
0 siblings, 0 replies; 62+ messages in thread
From: Chen-Yu Tsai @ 2017-02-26 3:46 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara, linux-clk, devicetree,
linux-arm-kernel, linux-kernel, linux-sunxi, Marc Zyngier
Hi,
On Sun, Feb 26, 2017 at 9:19 AM, Icenowy Zheng <icenowy@aosc.xyz> wrote:
> From: Andre Przywara <andre.przywara@arm.com>
>
> The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
> Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
> updated. So we should really share almost the whole .dtsi.
> In preparation for that move the peripheral parts of the existing
> sun8i-h3.dtsi into a new sun8i-h3-h5.dtsi.
> The actual sun8i-h3.dtsi then includes that and defines the H3 specific
> parts on top of it.
> On the way get rid of skeleton.dtsi, as recommended in that very file.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> [Icenowy: also split out mmc, as well as pio and ccu's compatible]
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> Changes in v3:
> - Use label-based syntax to reference nodes in H3 DTSI file.
> Changes in v2:
> - Rebase on current linux-next (because of the add of audio codec)
>
> arch/arm/boot/dts/sun8i-h3.dtsi | 789 ++++-----------------
> .../boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} | 87 +--
> 2 files changed, 148 insertions(+), 728 deletions(-)
> rewrite arch/arm/boot/dts/sun8i-h3.dtsi (81%)
> copy arch/arm/boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} (88%)
>
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
> dissimilarity index 81%
> index 8a4d7894a11f..4209d974c3f4 100644
> --- a/arch/arm/boot/dts/sun8i-h3.dtsi
> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> @@ -1,648 +1,141 @@
> -/*
> - * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
> - *
> - * This file is dual-licensed: you can use it either under the terms
> - * of the GPL or the X11 license, at your option. Note that this dual
> - * licensing only applies to this file, and not this project as a
> - * whole.
> - *
> - * a) This file is free software; you can redistribute it and/or
> - * modify it under the terms of the GNU General Public License as
> - * published by the Free Software Foundation; either version 2 of the
> - * License, or (at your option) any later version.
> - *
> - * This file is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> - * GNU General Public License for more details.
> - *
> - * Or, alternatively,
> - *
> - * b) Permission is hereby granted, free of charge, to any person
> - * obtaining a copy of this software and associated documentation
> - * files (the "Software"), to deal in the Software without
> - * restriction, including without limitation the rights to use,
> - * copy, modify, merge, publish, distribute, sublicense, and/or
> - * sell copies of the Software, and to permit persons to whom the
> - * Software is furnished to do so, subject to the following
> - * conditions:
> - *
> - * The above copyright notice and this permission notice shall be
> - * included in all copies or substantial portions of the Software.
> - *
> - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> - * OTHER DEALINGS IN THE SOFTWARE.
> - */
> -
> -#include "skeleton.dtsi"
> -
> -#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
> -#include <dt-bindings/interrupt-controller/arm-gic.h>
> -#include <dt-bindings/pinctrl/sun4i-a10.h>
> -#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
> -
> -/ {
> - interrupt-parent = <&gic>;
> -
> - cpus {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - cpu@0 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <0>;
> - };
> -
> - cpu@1 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <1>;
> - };
> -
> - cpu@2 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <2>;
> - };
> -
> - cpu@3 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <3>;
> - };
> - };
> -
> - timer {
> - compatible = "arm,armv7-timer";
> - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> - };
> -
> - clocks {
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> -
> - osc24M: osc24M_clk {
> - #clock-cells = <0>;
> - compatible = "fixed-clock";
> - clock-frequency = <24000000>;
> - clock-output-names = "osc24M";
> - };
> -
> - osc32k: osc32k_clk {
> - #clock-cells = <0>;
> - compatible = "fixed-clock";
> - clock-frequency = <32768>;
> - clock-output-names = "osc32k";
> - };
> -
> - apb0: apb0_clk {
> - compatible = "fixed-factor-clock";
> - #clock-cells = <0>;
> - clock-div = <1>;
> - clock-mult = <1>;
> - clocks = <&osc24M>;
> - clock-output-names = "apb0";
> - };
> -
> - apb0_gates: clk@01f01428 {
> - compatible = "allwinner,sun8i-h3-apb0-gates-clk",
> - "allwinner,sun4i-a10-gates-clk";
> - reg = <0x01f01428 0x4>;
> - #clock-cells = <1>;
> - clocks = <&apb0>;
> - clock-indices = <0>, <1>;
> - clock-output-names = "apb0_pio", "apb0_ir";
> - };
> -
> - ir_clk: ir_clk@01f01454 {
> - compatible = "allwinner,sun4i-a10-mod0-clk";
> - reg = <0x01f01454 0x4>;
> - #clock-cells = <0>;
> - clocks = <&osc32k>, <&osc24M>;
> - clock-output-names = "ir";
> - };
> - };
> -
> - soc {
> - compatible = "simple-bus";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> -
> - dma: dma-controller@01c02000 {
> - compatible = "allwinner,sun8i-h3-dma";
> - reg = <0x01c02000 0x1000>;
> - interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_DMA>;
> - resets = <&ccu RST_BUS_DMA>;
> - #dma-cells = <1>;
> - };
> -
> - mmc0: mmc@01c0f000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> - reg = <0x01c0f000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC0>,
> - <&ccu CLK_MMC0>,
> - <&ccu CLK_MMC0_OUTPUT>,
> - <&ccu CLK_MMC0_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> - resets = <&ccu RST_BUS_MMC0>;
> - reset-names = "ahb";
> - interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - mmc1: mmc@01c10000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> - reg = <0x01c10000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC1>,
> - <&ccu CLK_MMC1>,
> - <&ccu CLK_MMC1_OUTPUT>,
> - <&ccu CLK_MMC1_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> - resets = <&ccu RST_BUS_MMC1>;
> - reset-names = "ahb";
> - interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - mmc2: mmc@01c11000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> - reg = <0x01c11000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC2>,
> - <&ccu CLK_MMC2>,
> - <&ccu CLK_MMC2_OUTPUT>,
> - <&ccu CLK_MMC2_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> - resets = <&ccu RST_BUS_MMC2>;
> - reset-names = "ahb";
> - interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - usbphy: phy@01c19400 {
> - compatible = "allwinner,sun8i-h3-usb-phy";
> - reg = <0x01c19400 0x2c>,
> - <0x01c1a800 0x4>,
> - <0x01c1b800 0x4>,
> - <0x01c1c800 0x4>,
> - <0x01c1d800 0x4>;
> - reg-names = "phy_ctrl",
> - "pmu0",
> - "pmu1",
> - "pmu2",
> - "pmu3";
> - clocks = <&ccu CLK_USB_PHY0>,
> - <&ccu CLK_USB_PHY1>,
> - <&ccu CLK_USB_PHY2>,
> - <&ccu CLK_USB_PHY3>;
> - clock-names = "usb0_phy",
> - "usb1_phy",
> - "usb2_phy",
> - "usb3_phy";
> - resets = <&ccu RST_USB_PHY0>,
> - <&ccu RST_USB_PHY1>,
> - <&ccu RST_USB_PHY2>,
> - <&ccu RST_USB_PHY3>;
> - reset-names = "usb0_reset",
> - "usb1_reset",
> - "usb2_reset",
> - "usb3_reset";
> - status = "disabled";
> - #phy-cells = <1>;
> - };
> -
> - ehci1: usb@01c1b000 {
> - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> - reg = <0x01c1b000 0x100>;
> - interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
> - resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
> - phys = <&usbphy 1>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ohci1: usb@01c1b400 {
> - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> - reg = <0x01c1b400 0x100>;
> - interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
> - <&ccu CLK_USB_OHCI1>;
> - resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
> - phys = <&usbphy 1>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ehci2: usb@01c1c000 {
> - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> - reg = <0x01c1c000 0x100>;
> - interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
> - resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
> - phys = <&usbphy 2>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ohci2: usb@01c1c400 {
> - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> - reg = <0x01c1c400 0x100>;
> - interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
> - <&ccu CLK_USB_OHCI2>;
> - resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
> - phys = <&usbphy 2>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ehci3: usb@01c1d000 {
> - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> - reg = <0x01c1d000 0x100>;
> - interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
> - resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
> - phys = <&usbphy 3>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ohci3: usb@01c1d400 {
> - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> - reg = <0x01c1d400 0x100>;
> - interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
> - <&ccu CLK_USB_OHCI3>;
> - resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
> - phys = <&usbphy 3>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ccu: clock@01c20000 {
> - compatible = "allwinner,sun8i-h3-ccu";
> - reg = <0x01c20000 0x400>;
> - clocks = <&osc24M>, <&osc32k>;
> - clock-names = "hosc", "losc";
> - #clock-cells = <1>;
> - #reset-cells = <1>;
> - };
> -
> - pio: pinctrl@01c20800 {
> - compatible = "allwinner,sun8i-h3-pinctrl";
> - reg = <0x01c20800 0x400>;
> - interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
> - clock-names = "apb", "hosc", "losc";
> - gpio-controller;
> - #gpio-cells = <3>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> -
> - i2c0_pins: i2c0 {
> - pins = "PA11", "PA12";
> - function = "i2c0";
> - };
> -
> - i2c1_pins: i2c1 {
> - pins = "PA18", "PA19";
> - function = "i2c1";
> - };
> -
> - i2c2_pins: i2c2 {
> - pins = "PE12", "PE13";
> - function = "i2c2";
> - };
> -
> - mmc0_pins_a: mmc0@0 {
> - pins = "PF0", "PF1", "PF2", "PF3",
> - "PF4", "PF5";
> - function = "mmc0";
> - drive-strength = <30>;
> - bias-pull-up;
> - };
> -
> - mmc0_cd_pin: mmc0_cd_pin@0 {
> - pins = "PF6";
> - function = "gpio_in";
> - bias-pull-up;
> - };
> -
> - mmc1_pins_a: mmc1@0 {
> - pins = "PG0", "PG1", "PG2", "PG3",
> - "PG4", "PG5";
> - function = "mmc1";
> - drive-strength = <30>;
> - bias-pull-up;
> - };
> -
> - mmc2_8bit_pins: mmc2_8bit {
> - pins = "PC5", "PC6", "PC8",
> - "PC9", "PC10", "PC11",
> - "PC12", "PC13", "PC14",
> - "PC15", "PC16";
> - function = "mmc2";
> - drive-strength = <30>;
> - bias-pull-up;
> - };
> -
> - spdif_tx_pins_a: spdif@0 {
> - pins = "PA17";
> - function = "spdif";
> - };
> -
> - spi0_pins: spi0 {
> - pins = "PC0", "PC1", "PC2", "PC3";
> - function = "spi0";
> - };
> -
> - spi1_pins: spi1 {
> - pins = "PA15", "PA16", "PA14", "PA13";
> - function = "spi1";
> - };
> -
> - uart0_pins_a: uart0@0 {
> - pins = "PA4", "PA5";
> - function = "uart0";
> - };
> -
> - uart1_pins: uart1 {
> - pins = "PG6", "PG7";
> - function = "uart1";
> - };
> -
> - uart1_rts_cts_pins: uart1_rts_cts {
> - pins = "PG8", "PG9";
> - function = "uart1";
> - };
> -
> - uart2_pins: uart2 {
> - pins = "PA0", "PA1";
> - function = "uart2";
> - };
> -
> - uart3_pins: uart3 {
> - pins = "PA13", "PA14";
> - function = "uart3";
> - };
> - };
> -
> - timer@01c20c00 {
> - compatible = "allwinner,sun4i-a10-timer";
> - reg = <0x01c20c00 0xa0>;
> - interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&osc24M>;
> - };
> -
> - spi0: spi@01c68000 {
> - compatible = "allwinner,sun8i-h3-spi";
> - reg = <0x01c68000 0x1000>;
> - interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
> - clock-names = "ahb", "mod";
> - dmas = <&dma 23>, <&dma 23>;
> - dma-names = "rx", "tx";
> - pinctrl-names = "default";
> - pinctrl-0 = <&spi0_pins>;
> - resets = <&ccu RST_BUS_SPI0>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - spi1: spi@01c69000 {
> - compatible = "allwinner,sun8i-h3-spi";
> - reg = <0x01c69000 0x1000>;
> - interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
> - clock-names = "ahb", "mod";
> - dmas = <&dma 24>, <&dma 24>;
> - dma-names = "rx", "tx";
> - pinctrl-names = "default";
> - pinctrl-0 = <&spi1_pins>;
> - resets = <&ccu RST_BUS_SPI1>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - wdt0: watchdog@01c20ca0 {
> - compatible = "allwinner,sun6i-a31-wdt";
> - reg = <0x01c20ca0 0x20>;
> - interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> - };
> -
> - spdif: spdif@01c21000 {
> - #sound-dai-cells = <0>;
> - compatible = "allwinner,sun8i-h3-spdif";
> - reg = <0x01c21000 0x400>;
> - interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
> - resets = <&ccu RST_BUS_SPDIF>;
> - clock-names = "apb", "spdif";
> - dmas = <&dma 2>;
> - dma-names = "tx";
> - status = "disabled";
> - };
> -
> - pwm: pwm@01c21400 {
> - compatible = "allwinner,sun8i-h3-pwm";
> - reg = <0x01c21400 0x8>;
> - clocks = <&osc24M>;
> - #pwm-cells = <3>;
> - status = "disabled";
> - };
> -
> - codec: codec@01c22c00 {
> - #sound-dai-cells = <0>;
> - compatible = "allwinner,sun8i-h3-codec";
> - reg = <0x01c22c00 0x400>;
> - interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
> - clock-names = "apb", "codec";
> - resets = <&ccu RST_BUS_CODEC>;
> - dmas = <&dma 15>, <&dma 15>;
> - dma-names = "rx", "tx";
> - allwinner,codec-analog-controls = <&codec_analog>;
> - status = "disabled";
> - };
> -
> - uart0: serial@01c28000 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28000 0x400>;
> - interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART0>;
> - resets = <&ccu RST_BUS_UART0>;
> - dmas = <&dma 6>, <&dma 6>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - uart1: serial@01c28400 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28400 0x400>;
> - interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART1>;
> - resets = <&ccu RST_BUS_UART1>;
> - dmas = <&dma 7>, <&dma 7>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - uart2: serial@01c28800 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28800 0x400>;
> - interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART2>;
> - resets = <&ccu RST_BUS_UART2>;
> - dmas = <&dma 8>, <&dma 8>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - uart3: serial@01c28c00 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28c00 0x400>;
> - interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART3>;
> - resets = <&ccu RST_BUS_UART3>;
> - dmas = <&dma 9>, <&dma 9>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - i2c0: i2c@01c2ac00 {
> - compatible = "allwinner,sun6i-a31-i2c";
> - reg = <0x01c2ac00 0x400>;
> - interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_I2C0>;
> - resets = <&ccu RST_BUS_I2C0>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c0_pins>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - i2c1: i2c@01c2b000 {
> - compatible = "allwinner,sun6i-a31-i2c";
> - reg = <0x01c2b000 0x400>;
> - interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_I2C1>;
> - resets = <&ccu RST_BUS_I2C1>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c1_pins>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - i2c2: i2c@01c2b400 {
> - compatible = "allwinner,sun6i-a31-i2c";
> - reg = <0x01c2b000 0x400>;
> - interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_I2C2>;
> - resets = <&ccu RST_BUS_I2C2>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c2_pins>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - gic: interrupt-controller@01c81000 {
> - compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> - reg = <0x01c81000 0x1000>,
> - <0x01c82000 0x2000>,
> - <0x01c84000 0x2000>,
> - <0x01c86000 0x2000>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> - };
> -
> - rtc: rtc@01f00000 {
> - compatible = "allwinner,sun6i-a31-rtc";
> - reg = <0x01f00000 0x54>;
> - interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> - };
> -
> - apb0_reset: reset@01f014b0 {
> - reg = <0x01f014b0 0x4>;
> - compatible = "allwinner,sun6i-a31-clock-reset";
> - #reset-cells = <1>;
> - };
> -
> - codec_analog: codec-analog@01f015c0 {
> - compatible = "allwinner,sun8i-h3-codec-analog";
> - reg = <0x01f015c0 0x4>;
> - };
> -
> - ir: ir@01f02000 {
> - compatible = "allwinner,sun5i-a13-ir";
> - clocks = <&apb0_gates 1>, <&ir_clk>;
> - clock-names = "apb", "ir";
> - resets = <&apb0_reset 1>;
> - interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> - reg = <0x01f02000 0x40>;
> - status = "disabled";
> - };
> -
> - r_pio: pinctrl@01f02c00 {
> - compatible = "allwinner,sun8i-h3-r-pinctrl";
> - reg = <0x01f02c00 0x400>;
> - interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
> - clock-names = "apb", "hosc", "losc";
> - resets = <&apb0_reset 0>;
> - gpio-controller;
> - #gpio-cells = <3>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> -
> - ir_pins_a: ir@0 {
> - pins = "PL11";
> - function = "s_cir_rx";
> - };
> - };
> - };
> -};
> +/*
> + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "sunxi-h3-h5.dtsi"
> +
> +/ {
> + interrupt-parent = <&gic>;
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu@0 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <0>;
> + };
> +
> + cpu@1 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <1>;
> + };
> +
> + cpu@2 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <2>;
> + };
> +
> + cpu@3 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <3>;
> + };
> + };
> +
> + timer {
> + compatible = "arm,armv7-timer";
> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + soc {
> + gic: interrupt-controller@01c81000 {
> + compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> + reg = <0x01c81000 0x1000>,
> + <0x01c82000 0x2000>,
> + <0x01c84000 0x2000>,
> + <0x01c86000 0x2000>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> + };
> +};
> +
> +&ccu {
> + compatible = "allwinner,sun8i-h3-ccu";
> +};
> +
> +&mmc0 {
> + compatible = "allwinner,sun7i-a20-mmc";
> + clocks = <&ccu CLK_BUS_MMC0>,
> + <&ccu CLK_MMC0>,
> + <&ccu CLK_MMC0_OUTPUT>,
> + <&ccu CLK_MMC0_SAMPLE>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> +};
> +
> +&mmc1 {
> + compatible = "allwinner,sun7i-a20-mmc";
> + clocks = <&ccu CLK_BUS_MMC1>,
> + <&ccu CLK_MMC1>,
> + <&ccu CLK_MMC1_OUTPUT>,
> + <&ccu CLK_MMC1_SAMPLE>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> +};
> +
> +&mmc2 {
> + compatible = "allwinner,sun7i-a20-mmc";
> + clocks = <&ccu CLK_BUS_MMC2>,
> + <&ccu CLK_MMC2>,
> + <&ccu CLK_MMC2_OUTPUT>,
> + <&ccu CLK_MMC2_SAMPLE>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> +};
> +
> +&pio {
> + compatible = "allwinner,sun8i-h3-pinctrl";
> +};
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> similarity index 88%
> copy from arch/arm/boot/dts/sun8i-h3.dtsi
> copy to arch/arm/boot/dts/sunxi-h3-h5.dtsi
> index 8a4d7894a11f..966dc4211c4d 100644
> --- a/arch/arm/boot/dts/sun8i-h3.dtsi
> +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> @@ -40,52 +40,14 @@
> * OTHER DEALINGS IN THE SOFTWARE.
> */
>
> -#include "skeleton.dtsi"
> -
> #include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/pinctrl/sun4i-a10.h>
> #include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
>
> / {
> - interrupt-parent = <&gic>;
> -
> - cpus {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - cpu@0 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <0>;
> - };
> -
> - cpu@1 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <1>;
> - };
> -
> - cpu@2 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <2>;
> - };
> -
> - cpu@3 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <3>;
> - };
> - };
> -
> - timer {
> - compatible = "arm,armv7-timer";
> - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> - };
> + #address-cells = <1>;
> + #size-cells = <1>;
>
> clocks {
> #address-cells = <1>;
> @@ -150,16 +112,8 @@
> };
>
> mmc0: mmc@01c0f000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> + /* compatible and clocks are in per SoC .dtsi file */
> reg = <0x01c0f000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC0>,
> - <&ccu CLK_MMC0>,
> - <&ccu CLK_MMC0_OUTPUT>,
> - <&ccu CLK_MMC0_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> resets = <&ccu RST_BUS_MMC0>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> @@ -169,16 +123,8 @@
> };
>
> mmc1: mmc@01c10000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> + /* compatible and clocks are in per SoC .dtsi file */
> reg = <0x01c10000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC1>,
> - <&ccu CLK_MMC1>,
> - <&ccu CLK_MMC1_OUTPUT>,
> - <&ccu CLK_MMC1_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> resets = <&ccu RST_BUS_MMC1>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> @@ -188,16 +134,8 @@
> };
>
> mmc2: mmc@01c11000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> + /* compatible and clocks are in per SoC .dtsi file */
> reg = <0x01c11000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC2>,
> - <&ccu CLK_MMC2>,
> - <&ccu CLK_MMC2_OUTPUT>,
> - <&ccu CLK_MMC2_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> resets = <&ccu RST_BUS_MMC2>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> @@ -308,7 +246,7 @@
> };
>
> ccu: clock@01c20000 {
> - compatible = "allwinner,sun8i-h3-ccu";
> + /* compatible is in per SoC .dtsi file */
> reg = <0x01c20000 0x400>;
> clocks = <&osc24M>, <&osc32k>;
> clock-names = "hosc", "losc";
> @@ -317,7 +255,7 @@
> };
>
> pio: pinctrl@01c20800 {
> - compatible = "allwinner,sun8i-h3-pinctrl";
> + /* compatible is in per SoC .dtsi file */
> reg = <0x01c20800 0x400>;
> interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> @@ -588,17 +526,6 @@
> #size-cells = <0>;
> };
>
> - gic: interrupt-controller@01c81000 {
> - compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> - reg = <0x01c81000 0x1000>,
> - <0x01c82000 0x2000>,
> - <0x01c84000 0x2000>,
> - <0x01c86000 0x2000>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
The gic bits seem to be the same for both SoCs, aside from the
different compatible
string. Marc had sent a series to change them all to arm,gic-400, which is the
proper name for it, but it wasn't merged. I'm assuming the compatibles
are equal?
If so then it can also be shared.
The rest looks ok.
ChenYu
> - };
> -
> rtc: rtc@01f00000 {
> compatible = "allwinner,sun6i-a31-rtc";
> reg = <0x01f00000 0x54>;
> --
> 2.11.1
>
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 5/7] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-02-26 3:46 ` Chen-Yu Tsai
0 siblings, 0 replies; 62+ messages in thread
From: Chen-Yu Tsai @ 2017-02-26 3:46 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara, linux-clk, devicetree,
linux-arm-kernel, linux-kernel, linux-sunxi, Marc Zyngier
Hi,
On Sun, Feb 26, 2017 at 9:19 AM, Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org> wrote:
> From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
>
> The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
> Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
> updated. So we should really share almost the whole .dtsi.
> In preparation for that move the peripheral parts of the existing
> sun8i-h3.dtsi into a new sun8i-h3-h5.dtsi.
> The actual sun8i-h3.dtsi then includes that and defines the H3 specific
> parts on top of it.
> On the way get rid of skeleton.dtsi, as recommended in that very file.
>
> Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
> [Icenowy: also split out mmc, as well as pio and ccu's compatible]
> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
> ---
> Changes in v3:
> - Use label-based syntax to reference nodes in H3 DTSI file.
> Changes in v2:
> - Rebase on current linux-next (because of the add of audio codec)
>
> arch/arm/boot/dts/sun8i-h3.dtsi | 789 ++++-----------------
> .../boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} | 87 +--
> 2 files changed, 148 insertions(+), 728 deletions(-)
> rewrite arch/arm/boot/dts/sun8i-h3.dtsi (81%)
> copy arch/arm/boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} (88%)
>
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
> dissimilarity index 81%
> index 8a4d7894a11f..4209d974c3f4 100644
> --- a/arch/arm/boot/dts/sun8i-h3.dtsi
> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> @@ -1,648 +1,141 @@
> -/*
> - * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> - *
> - * This file is dual-licensed: you can use it either under the terms
> - * of the GPL or the X11 license, at your option. Note that this dual
> - * licensing only applies to this file, and not this project as a
> - * whole.
> - *
> - * a) This file is free software; you can redistribute it and/or
> - * modify it under the terms of the GNU General Public License as
> - * published by the Free Software Foundation; either version 2 of the
> - * License, or (at your option) any later version.
> - *
> - * This file is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> - * GNU General Public License for more details.
> - *
> - * Or, alternatively,
> - *
> - * b) Permission is hereby granted, free of charge, to any person
> - * obtaining a copy of this software and associated documentation
> - * files (the "Software"), to deal in the Software without
> - * restriction, including without limitation the rights to use,
> - * copy, modify, merge, publish, distribute, sublicense, and/or
> - * sell copies of the Software, and to permit persons to whom the
> - * Software is furnished to do so, subject to the following
> - * conditions:
> - *
> - * The above copyright notice and this permission notice shall be
> - * included in all copies or substantial portions of the Software.
> - *
> - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> - * OTHER DEALINGS IN THE SOFTWARE.
> - */
> -
> -#include "skeleton.dtsi"
> -
> -#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
> -#include <dt-bindings/interrupt-controller/arm-gic.h>
> -#include <dt-bindings/pinctrl/sun4i-a10.h>
> -#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
> -
> -/ {
> - interrupt-parent = <&gic>;
> -
> - cpus {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - cpu@0 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <0>;
> - };
> -
> - cpu@1 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <1>;
> - };
> -
> - cpu@2 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <2>;
> - };
> -
> - cpu@3 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <3>;
> - };
> - };
> -
> - timer {
> - compatible = "arm,armv7-timer";
> - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> - };
> -
> - clocks {
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> -
> - osc24M: osc24M_clk {
> - #clock-cells = <0>;
> - compatible = "fixed-clock";
> - clock-frequency = <24000000>;
> - clock-output-names = "osc24M";
> - };
> -
> - osc32k: osc32k_clk {
> - #clock-cells = <0>;
> - compatible = "fixed-clock";
> - clock-frequency = <32768>;
> - clock-output-names = "osc32k";
> - };
> -
> - apb0: apb0_clk {
> - compatible = "fixed-factor-clock";
> - #clock-cells = <0>;
> - clock-div = <1>;
> - clock-mult = <1>;
> - clocks = <&osc24M>;
> - clock-output-names = "apb0";
> - };
> -
> - apb0_gates: clk@01f01428 {
> - compatible = "allwinner,sun8i-h3-apb0-gates-clk",
> - "allwinner,sun4i-a10-gates-clk";
> - reg = <0x01f01428 0x4>;
> - #clock-cells = <1>;
> - clocks = <&apb0>;
> - clock-indices = <0>, <1>;
> - clock-output-names = "apb0_pio", "apb0_ir";
> - };
> -
> - ir_clk: ir_clk@01f01454 {
> - compatible = "allwinner,sun4i-a10-mod0-clk";
> - reg = <0x01f01454 0x4>;
> - #clock-cells = <0>;
> - clocks = <&osc32k>, <&osc24M>;
> - clock-output-names = "ir";
> - };
> - };
> -
> - soc {
> - compatible = "simple-bus";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> -
> - dma: dma-controller@01c02000 {
> - compatible = "allwinner,sun8i-h3-dma";
> - reg = <0x01c02000 0x1000>;
> - interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_DMA>;
> - resets = <&ccu RST_BUS_DMA>;
> - #dma-cells = <1>;
> - };
> -
> - mmc0: mmc@01c0f000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> - reg = <0x01c0f000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC0>,
> - <&ccu CLK_MMC0>,
> - <&ccu CLK_MMC0_OUTPUT>,
> - <&ccu CLK_MMC0_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> - resets = <&ccu RST_BUS_MMC0>;
> - reset-names = "ahb";
> - interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - mmc1: mmc@01c10000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> - reg = <0x01c10000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC1>,
> - <&ccu CLK_MMC1>,
> - <&ccu CLK_MMC1_OUTPUT>,
> - <&ccu CLK_MMC1_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> - resets = <&ccu RST_BUS_MMC1>;
> - reset-names = "ahb";
> - interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - mmc2: mmc@01c11000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> - reg = <0x01c11000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC2>,
> - <&ccu CLK_MMC2>,
> - <&ccu CLK_MMC2_OUTPUT>,
> - <&ccu CLK_MMC2_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> - resets = <&ccu RST_BUS_MMC2>;
> - reset-names = "ahb";
> - interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - usbphy: phy@01c19400 {
> - compatible = "allwinner,sun8i-h3-usb-phy";
> - reg = <0x01c19400 0x2c>,
> - <0x01c1a800 0x4>,
> - <0x01c1b800 0x4>,
> - <0x01c1c800 0x4>,
> - <0x01c1d800 0x4>;
> - reg-names = "phy_ctrl",
> - "pmu0",
> - "pmu1",
> - "pmu2",
> - "pmu3";
> - clocks = <&ccu CLK_USB_PHY0>,
> - <&ccu CLK_USB_PHY1>,
> - <&ccu CLK_USB_PHY2>,
> - <&ccu CLK_USB_PHY3>;
> - clock-names = "usb0_phy",
> - "usb1_phy",
> - "usb2_phy",
> - "usb3_phy";
> - resets = <&ccu RST_USB_PHY0>,
> - <&ccu RST_USB_PHY1>,
> - <&ccu RST_USB_PHY2>,
> - <&ccu RST_USB_PHY3>;
> - reset-names = "usb0_reset",
> - "usb1_reset",
> - "usb2_reset",
> - "usb3_reset";
> - status = "disabled";
> - #phy-cells = <1>;
> - };
> -
> - ehci1: usb@01c1b000 {
> - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> - reg = <0x01c1b000 0x100>;
> - interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
> - resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
> - phys = <&usbphy 1>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ohci1: usb@01c1b400 {
> - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> - reg = <0x01c1b400 0x100>;
> - interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
> - <&ccu CLK_USB_OHCI1>;
> - resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
> - phys = <&usbphy 1>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ehci2: usb@01c1c000 {
> - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> - reg = <0x01c1c000 0x100>;
> - interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
> - resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
> - phys = <&usbphy 2>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ohci2: usb@01c1c400 {
> - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> - reg = <0x01c1c400 0x100>;
> - interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
> - <&ccu CLK_USB_OHCI2>;
> - resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
> - phys = <&usbphy 2>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ehci3: usb@01c1d000 {
> - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> - reg = <0x01c1d000 0x100>;
> - interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
> - resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
> - phys = <&usbphy 3>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ohci3: usb@01c1d400 {
> - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> - reg = <0x01c1d400 0x100>;
> - interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
> - <&ccu CLK_USB_OHCI3>;
> - resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
> - phys = <&usbphy 3>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ccu: clock@01c20000 {
> - compatible = "allwinner,sun8i-h3-ccu";
> - reg = <0x01c20000 0x400>;
> - clocks = <&osc24M>, <&osc32k>;
> - clock-names = "hosc", "losc";
> - #clock-cells = <1>;
> - #reset-cells = <1>;
> - };
> -
> - pio: pinctrl@01c20800 {
> - compatible = "allwinner,sun8i-h3-pinctrl";
> - reg = <0x01c20800 0x400>;
> - interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
> - clock-names = "apb", "hosc", "losc";
> - gpio-controller;
> - #gpio-cells = <3>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> -
> - i2c0_pins: i2c0 {
> - pins = "PA11", "PA12";
> - function = "i2c0";
> - };
> -
> - i2c1_pins: i2c1 {
> - pins = "PA18", "PA19";
> - function = "i2c1";
> - };
> -
> - i2c2_pins: i2c2 {
> - pins = "PE12", "PE13";
> - function = "i2c2";
> - };
> -
> - mmc0_pins_a: mmc0@0 {
> - pins = "PF0", "PF1", "PF2", "PF3",
> - "PF4", "PF5";
> - function = "mmc0";
> - drive-strength = <30>;
> - bias-pull-up;
> - };
> -
> - mmc0_cd_pin: mmc0_cd_pin@0 {
> - pins = "PF6";
> - function = "gpio_in";
> - bias-pull-up;
> - };
> -
> - mmc1_pins_a: mmc1@0 {
> - pins = "PG0", "PG1", "PG2", "PG3",
> - "PG4", "PG5";
> - function = "mmc1";
> - drive-strength = <30>;
> - bias-pull-up;
> - };
> -
> - mmc2_8bit_pins: mmc2_8bit {
> - pins = "PC5", "PC6", "PC8",
> - "PC9", "PC10", "PC11",
> - "PC12", "PC13", "PC14",
> - "PC15", "PC16";
> - function = "mmc2";
> - drive-strength = <30>;
> - bias-pull-up;
> - };
> -
> - spdif_tx_pins_a: spdif@0 {
> - pins = "PA17";
> - function = "spdif";
> - };
> -
> - spi0_pins: spi0 {
> - pins = "PC0", "PC1", "PC2", "PC3";
> - function = "spi0";
> - };
> -
> - spi1_pins: spi1 {
> - pins = "PA15", "PA16", "PA14", "PA13";
> - function = "spi1";
> - };
> -
> - uart0_pins_a: uart0@0 {
> - pins = "PA4", "PA5";
> - function = "uart0";
> - };
> -
> - uart1_pins: uart1 {
> - pins = "PG6", "PG7";
> - function = "uart1";
> - };
> -
> - uart1_rts_cts_pins: uart1_rts_cts {
> - pins = "PG8", "PG9";
> - function = "uart1";
> - };
> -
> - uart2_pins: uart2 {
> - pins = "PA0", "PA1";
> - function = "uart2";
> - };
> -
> - uart3_pins: uart3 {
> - pins = "PA13", "PA14";
> - function = "uart3";
> - };
> - };
> -
> - timer@01c20c00 {
> - compatible = "allwinner,sun4i-a10-timer";
> - reg = <0x01c20c00 0xa0>;
> - interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&osc24M>;
> - };
> -
> - spi0: spi@01c68000 {
> - compatible = "allwinner,sun8i-h3-spi";
> - reg = <0x01c68000 0x1000>;
> - interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
> - clock-names = "ahb", "mod";
> - dmas = <&dma 23>, <&dma 23>;
> - dma-names = "rx", "tx";
> - pinctrl-names = "default";
> - pinctrl-0 = <&spi0_pins>;
> - resets = <&ccu RST_BUS_SPI0>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - spi1: spi@01c69000 {
> - compatible = "allwinner,sun8i-h3-spi";
> - reg = <0x01c69000 0x1000>;
> - interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
> - clock-names = "ahb", "mod";
> - dmas = <&dma 24>, <&dma 24>;
> - dma-names = "rx", "tx";
> - pinctrl-names = "default";
> - pinctrl-0 = <&spi1_pins>;
> - resets = <&ccu RST_BUS_SPI1>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - wdt0: watchdog@01c20ca0 {
> - compatible = "allwinner,sun6i-a31-wdt";
> - reg = <0x01c20ca0 0x20>;
> - interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> - };
> -
> - spdif: spdif@01c21000 {
> - #sound-dai-cells = <0>;
> - compatible = "allwinner,sun8i-h3-spdif";
> - reg = <0x01c21000 0x400>;
> - interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
> - resets = <&ccu RST_BUS_SPDIF>;
> - clock-names = "apb", "spdif";
> - dmas = <&dma 2>;
> - dma-names = "tx";
> - status = "disabled";
> - };
> -
> - pwm: pwm@01c21400 {
> - compatible = "allwinner,sun8i-h3-pwm";
> - reg = <0x01c21400 0x8>;
> - clocks = <&osc24M>;
> - #pwm-cells = <3>;
> - status = "disabled";
> - };
> -
> - codec: codec@01c22c00 {
> - #sound-dai-cells = <0>;
> - compatible = "allwinner,sun8i-h3-codec";
> - reg = <0x01c22c00 0x400>;
> - interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
> - clock-names = "apb", "codec";
> - resets = <&ccu RST_BUS_CODEC>;
> - dmas = <&dma 15>, <&dma 15>;
> - dma-names = "rx", "tx";
> - allwinner,codec-analog-controls = <&codec_analog>;
> - status = "disabled";
> - };
> -
> - uart0: serial@01c28000 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28000 0x400>;
> - interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART0>;
> - resets = <&ccu RST_BUS_UART0>;
> - dmas = <&dma 6>, <&dma 6>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - uart1: serial@01c28400 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28400 0x400>;
> - interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART1>;
> - resets = <&ccu RST_BUS_UART1>;
> - dmas = <&dma 7>, <&dma 7>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - uart2: serial@01c28800 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28800 0x400>;
> - interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART2>;
> - resets = <&ccu RST_BUS_UART2>;
> - dmas = <&dma 8>, <&dma 8>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - uart3: serial@01c28c00 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28c00 0x400>;
> - interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART3>;
> - resets = <&ccu RST_BUS_UART3>;
> - dmas = <&dma 9>, <&dma 9>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - i2c0: i2c@01c2ac00 {
> - compatible = "allwinner,sun6i-a31-i2c";
> - reg = <0x01c2ac00 0x400>;
> - interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_I2C0>;
> - resets = <&ccu RST_BUS_I2C0>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c0_pins>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - i2c1: i2c@01c2b000 {
> - compatible = "allwinner,sun6i-a31-i2c";
> - reg = <0x01c2b000 0x400>;
> - interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_I2C1>;
> - resets = <&ccu RST_BUS_I2C1>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c1_pins>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - i2c2: i2c@01c2b400 {
> - compatible = "allwinner,sun6i-a31-i2c";
> - reg = <0x01c2b000 0x400>;
> - interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_I2C2>;
> - resets = <&ccu RST_BUS_I2C2>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c2_pins>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - gic: interrupt-controller@01c81000 {
> - compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> - reg = <0x01c81000 0x1000>,
> - <0x01c82000 0x2000>,
> - <0x01c84000 0x2000>,
> - <0x01c86000 0x2000>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> - };
> -
> - rtc: rtc@01f00000 {
> - compatible = "allwinner,sun6i-a31-rtc";
> - reg = <0x01f00000 0x54>;
> - interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> - };
> -
> - apb0_reset: reset@01f014b0 {
> - reg = <0x01f014b0 0x4>;
> - compatible = "allwinner,sun6i-a31-clock-reset";
> - #reset-cells = <1>;
> - };
> -
> - codec_analog: codec-analog@01f015c0 {
> - compatible = "allwinner,sun8i-h3-codec-analog";
> - reg = <0x01f015c0 0x4>;
> - };
> -
> - ir: ir@01f02000 {
> - compatible = "allwinner,sun5i-a13-ir";
> - clocks = <&apb0_gates 1>, <&ir_clk>;
> - clock-names = "apb", "ir";
> - resets = <&apb0_reset 1>;
> - interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> - reg = <0x01f02000 0x40>;
> - status = "disabled";
> - };
> -
> - r_pio: pinctrl@01f02c00 {
> - compatible = "allwinner,sun8i-h3-r-pinctrl";
> - reg = <0x01f02c00 0x400>;
> - interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
> - clock-names = "apb", "hosc", "losc";
> - resets = <&apb0_reset 0>;
> - gpio-controller;
> - #gpio-cells = <3>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> -
> - ir_pins_a: ir@0 {
> - pins = "PL11";
> - function = "s_cir_rx";
> - };
> - };
> - };
> -};
> +/*
> + * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "sunxi-h3-h5.dtsi"
> +
> +/ {
> + interrupt-parent = <&gic>;
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu@0 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <0>;
> + };
> +
> + cpu@1 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <1>;
> + };
> +
> + cpu@2 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <2>;
> + };
> +
> + cpu@3 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <3>;
> + };
> + };
> +
> + timer {
> + compatible = "arm,armv7-timer";
> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + soc {
> + gic: interrupt-controller@01c81000 {
> + compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> + reg = <0x01c81000 0x1000>,
> + <0x01c82000 0x2000>,
> + <0x01c84000 0x2000>,
> + <0x01c86000 0x2000>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> + };
> +};
> +
> +&ccu {
> + compatible = "allwinner,sun8i-h3-ccu";
> +};
> +
> +&mmc0 {
> + compatible = "allwinner,sun7i-a20-mmc";
> + clocks = <&ccu CLK_BUS_MMC0>,
> + <&ccu CLK_MMC0>,
> + <&ccu CLK_MMC0_OUTPUT>,
> + <&ccu CLK_MMC0_SAMPLE>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> +};
> +
> +&mmc1 {
> + compatible = "allwinner,sun7i-a20-mmc";
> + clocks = <&ccu CLK_BUS_MMC1>,
> + <&ccu CLK_MMC1>,
> + <&ccu CLK_MMC1_OUTPUT>,
> + <&ccu CLK_MMC1_SAMPLE>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> +};
> +
> +&mmc2 {
> + compatible = "allwinner,sun7i-a20-mmc";
> + clocks = <&ccu CLK_BUS_MMC2>,
> + <&ccu CLK_MMC2>,
> + <&ccu CLK_MMC2_OUTPUT>,
> + <&ccu CLK_MMC2_SAMPLE>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> +};
> +
> +&pio {
> + compatible = "allwinner,sun8i-h3-pinctrl";
> +};
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> similarity index 88%
> copy from arch/arm/boot/dts/sun8i-h3.dtsi
> copy to arch/arm/boot/dts/sunxi-h3-h5.dtsi
> index 8a4d7894a11f..966dc4211c4d 100644
> --- a/arch/arm/boot/dts/sun8i-h3.dtsi
> +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> @@ -40,52 +40,14 @@
> * OTHER DEALINGS IN THE SOFTWARE.
> */
>
> -#include "skeleton.dtsi"
> -
> #include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/pinctrl/sun4i-a10.h>
> #include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
>
> / {
> - interrupt-parent = <&gic>;
> -
> - cpus {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - cpu@0 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <0>;
> - };
> -
> - cpu@1 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <1>;
> - };
> -
> - cpu@2 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <2>;
> - };
> -
> - cpu@3 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <3>;
> - };
> - };
> -
> - timer {
> - compatible = "arm,armv7-timer";
> - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> - };
> + #address-cells = <1>;
> + #size-cells = <1>;
>
> clocks {
> #address-cells = <1>;
> @@ -150,16 +112,8 @@
> };
>
> mmc0: mmc@01c0f000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> + /* compatible and clocks are in per SoC .dtsi file */
> reg = <0x01c0f000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC0>,
> - <&ccu CLK_MMC0>,
> - <&ccu CLK_MMC0_OUTPUT>,
> - <&ccu CLK_MMC0_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> resets = <&ccu RST_BUS_MMC0>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> @@ -169,16 +123,8 @@
> };
>
> mmc1: mmc@01c10000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> + /* compatible and clocks are in per SoC .dtsi file */
> reg = <0x01c10000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC1>,
> - <&ccu CLK_MMC1>,
> - <&ccu CLK_MMC1_OUTPUT>,
> - <&ccu CLK_MMC1_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> resets = <&ccu RST_BUS_MMC1>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> @@ -188,16 +134,8 @@
> };
>
> mmc2: mmc@01c11000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> + /* compatible and clocks are in per SoC .dtsi file */
> reg = <0x01c11000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC2>,
> - <&ccu CLK_MMC2>,
> - <&ccu CLK_MMC2_OUTPUT>,
> - <&ccu CLK_MMC2_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> resets = <&ccu RST_BUS_MMC2>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> @@ -308,7 +246,7 @@
> };
>
> ccu: clock@01c20000 {
> - compatible = "allwinner,sun8i-h3-ccu";
> + /* compatible is in per SoC .dtsi file */
> reg = <0x01c20000 0x400>;
> clocks = <&osc24M>, <&osc32k>;
> clock-names = "hosc", "losc";
> @@ -317,7 +255,7 @@
> };
>
> pio: pinctrl@01c20800 {
> - compatible = "allwinner,sun8i-h3-pinctrl";
> + /* compatible is in per SoC .dtsi file */
> reg = <0x01c20800 0x400>;
> interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> @@ -588,17 +526,6 @@
> #size-cells = <0>;
> };
>
> - gic: interrupt-controller@01c81000 {
> - compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> - reg = <0x01c81000 0x1000>,
> - <0x01c82000 0x2000>,
> - <0x01c84000 0x2000>,
> - <0x01c86000 0x2000>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
The gic bits seem to be the same for both SoCs, aside from the
different compatible
string. Marc had sent a series to change them all to arm,gic-400, which is the
proper name for it, but it wasn't merged. I'm assuming the compatibles
are equal?
If so then it can also be shared.
The rest looks ok.
ChenYu
> - };
> -
> rtc: rtc@01f00000 {
> compatible = "allwinner,sun6i-a31-rtc";
> reg = <0x01f00000 0x54>;
> --
> 2.11.1
>
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 5/7] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-02-26 3:46 ` Chen-Yu Tsai
0 siblings, 0 replies; 62+ messages in thread
From: Chen-Yu Tsai @ 2017-02-26 3:46 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, Marc Zyngier, Catalin Marinas, linux-sunxi,
Will Deacon, linux-kernel, Chen-Yu Tsai, Rob Herring,
Andre Przywara, Maxime Ripard, linux-clk, linux-arm-kernel
Hi,
On Sun, Feb 26, 2017 at 9:19 AM, Icenowy Zheng <icenowy@aosc.xyz> wrote:
> From: Andre Przywara <andre.przywara@arm.com>
>
> The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
> Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
> updated. So we should really share almost the whole .dtsi.
> In preparation for that move the peripheral parts of the existing
> sun8i-h3.dtsi into a new sun8i-h3-h5.dtsi.
> The actual sun8i-h3.dtsi then includes that and defines the H3 specific
> parts on top of it.
> On the way get rid of skeleton.dtsi, as recommended in that very file.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> [Icenowy: also split out mmc, as well as pio and ccu's compatible]
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> Changes in v3:
> - Use label-based syntax to reference nodes in H3 DTSI file.
> Changes in v2:
> - Rebase on current linux-next (because of the add of audio codec)
>
> arch/arm/boot/dts/sun8i-h3.dtsi | 789 ++++-----------------
> .../boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} | 87 +--
> 2 files changed, 148 insertions(+), 728 deletions(-)
> rewrite arch/arm/boot/dts/sun8i-h3.dtsi (81%)
> copy arch/arm/boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} (88%)
>
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
> dissimilarity index 81%
> index 8a4d7894a11f..4209d974c3f4 100644
> --- a/arch/arm/boot/dts/sun8i-h3.dtsi
> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> @@ -1,648 +1,141 @@
> -/*
> - * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
> - *
> - * This file is dual-licensed: you can use it either under the terms
> - * of the GPL or the X11 license, at your option. Note that this dual
> - * licensing only applies to this file, and not this project as a
> - * whole.
> - *
> - * a) This file is free software; you can redistribute it and/or
> - * modify it under the terms of the GNU General Public License as
> - * published by the Free Software Foundation; either version 2 of the
> - * License, or (at your option) any later version.
> - *
> - * This file is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> - * GNU General Public License for more details.
> - *
> - * Or, alternatively,
> - *
> - * b) Permission is hereby granted, free of charge, to any person
> - * obtaining a copy of this software and associated documentation
> - * files (the "Software"), to deal in the Software without
> - * restriction, including without limitation the rights to use,
> - * copy, modify, merge, publish, distribute, sublicense, and/or
> - * sell copies of the Software, and to permit persons to whom the
> - * Software is furnished to do so, subject to the following
> - * conditions:
> - *
> - * The above copyright notice and this permission notice shall be
> - * included in all copies or substantial portions of the Software.
> - *
> - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> - * OTHER DEALINGS IN THE SOFTWARE.
> - */
> -
> -#include "skeleton.dtsi"
> -
> -#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
> -#include <dt-bindings/interrupt-controller/arm-gic.h>
> -#include <dt-bindings/pinctrl/sun4i-a10.h>
> -#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
> -
> -/ {
> - interrupt-parent = <&gic>;
> -
> - cpus {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - cpu@0 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <0>;
> - };
> -
> - cpu@1 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <1>;
> - };
> -
> - cpu@2 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <2>;
> - };
> -
> - cpu@3 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <3>;
> - };
> - };
> -
> - timer {
> - compatible = "arm,armv7-timer";
> - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> - };
> -
> - clocks {
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> -
> - osc24M: osc24M_clk {
> - #clock-cells = <0>;
> - compatible = "fixed-clock";
> - clock-frequency = <24000000>;
> - clock-output-names = "osc24M";
> - };
> -
> - osc32k: osc32k_clk {
> - #clock-cells = <0>;
> - compatible = "fixed-clock";
> - clock-frequency = <32768>;
> - clock-output-names = "osc32k";
> - };
> -
> - apb0: apb0_clk {
> - compatible = "fixed-factor-clock";
> - #clock-cells = <0>;
> - clock-div = <1>;
> - clock-mult = <1>;
> - clocks = <&osc24M>;
> - clock-output-names = "apb0";
> - };
> -
> - apb0_gates: clk@01f01428 {
> - compatible = "allwinner,sun8i-h3-apb0-gates-clk",
> - "allwinner,sun4i-a10-gates-clk";
> - reg = <0x01f01428 0x4>;
> - #clock-cells = <1>;
> - clocks = <&apb0>;
> - clock-indices = <0>, <1>;
> - clock-output-names = "apb0_pio", "apb0_ir";
> - };
> -
> - ir_clk: ir_clk@01f01454 {
> - compatible = "allwinner,sun4i-a10-mod0-clk";
> - reg = <0x01f01454 0x4>;
> - #clock-cells = <0>;
> - clocks = <&osc32k>, <&osc24M>;
> - clock-output-names = "ir";
> - };
> - };
> -
> - soc {
> - compatible = "simple-bus";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> -
> - dma: dma-controller@01c02000 {
> - compatible = "allwinner,sun8i-h3-dma";
> - reg = <0x01c02000 0x1000>;
> - interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_DMA>;
> - resets = <&ccu RST_BUS_DMA>;
> - #dma-cells = <1>;
> - };
> -
> - mmc0: mmc@01c0f000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> - reg = <0x01c0f000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC0>,
> - <&ccu CLK_MMC0>,
> - <&ccu CLK_MMC0_OUTPUT>,
> - <&ccu CLK_MMC0_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> - resets = <&ccu RST_BUS_MMC0>;
> - reset-names = "ahb";
> - interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - mmc1: mmc@01c10000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> - reg = <0x01c10000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC1>,
> - <&ccu CLK_MMC1>,
> - <&ccu CLK_MMC1_OUTPUT>,
> - <&ccu CLK_MMC1_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> - resets = <&ccu RST_BUS_MMC1>;
> - reset-names = "ahb";
> - interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - mmc2: mmc@01c11000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> - reg = <0x01c11000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC2>,
> - <&ccu CLK_MMC2>,
> - <&ccu CLK_MMC2_OUTPUT>,
> - <&ccu CLK_MMC2_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> - resets = <&ccu RST_BUS_MMC2>;
> - reset-names = "ahb";
> - interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - usbphy: phy@01c19400 {
> - compatible = "allwinner,sun8i-h3-usb-phy";
> - reg = <0x01c19400 0x2c>,
> - <0x01c1a800 0x4>,
> - <0x01c1b800 0x4>,
> - <0x01c1c800 0x4>,
> - <0x01c1d800 0x4>;
> - reg-names = "phy_ctrl",
> - "pmu0",
> - "pmu1",
> - "pmu2",
> - "pmu3";
> - clocks = <&ccu CLK_USB_PHY0>,
> - <&ccu CLK_USB_PHY1>,
> - <&ccu CLK_USB_PHY2>,
> - <&ccu CLK_USB_PHY3>;
> - clock-names = "usb0_phy",
> - "usb1_phy",
> - "usb2_phy",
> - "usb3_phy";
> - resets = <&ccu RST_USB_PHY0>,
> - <&ccu RST_USB_PHY1>,
> - <&ccu RST_USB_PHY2>,
> - <&ccu RST_USB_PHY3>;
> - reset-names = "usb0_reset",
> - "usb1_reset",
> - "usb2_reset",
> - "usb3_reset";
> - status = "disabled";
> - #phy-cells = <1>;
> - };
> -
> - ehci1: usb@01c1b000 {
> - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> - reg = <0x01c1b000 0x100>;
> - interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
> - resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
> - phys = <&usbphy 1>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ohci1: usb@01c1b400 {
> - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> - reg = <0x01c1b400 0x100>;
> - interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
> - <&ccu CLK_USB_OHCI1>;
> - resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
> - phys = <&usbphy 1>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ehci2: usb@01c1c000 {
> - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> - reg = <0x01c1c000 0x100>;
> - interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
> - resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
> - phys = <&usbphy 2>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ohci2: usb@01c1c400 {
> - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> - reg = <0x01c1c400 0x100>;
> - interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
> - <&ccu CLK_USB_OHCI2>;
> - resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
> - phys = <&usbphy 2>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ehci3: usb@01c1d000 {
> - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> - reg = <0x01c1d000 0x100>;
> - interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
> - resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
> - phys = <&usbphy 3>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ohci3: usb@01c1d400 {
> - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> - reg = <0x01c1d400 0x100>;
> - interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
> - <&ccu CLK_USB_OHCI3>;
> - resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
> - phys = <&usbphy 3>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ccu: clock@01c20000 {
> - compatible = "allwinner,sun8i-h3-ccu";
> - reg = <0x01c20000 0x400>;
> - clocks = <&osc24M>, <&osc32k>;
> - clock-names = "hosc", "losc";
> - #clock-cells = <1>;
> - #reset-cells = <1>;
> - };
> -
> - pio: pinctrl@01c20800 {
> - compatible = "allwinner,sun8i-h3-pinctrl";
> - reg = <0x01c20800 0x400>;
> - interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
> - clock-names = "apb", "hosc", "losc";
> - gpio-controller;
> - #gpio-cells = <3>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> -
> - i2c0_pins: i2c0 {
> - pins = "PA11", "PA12";
> - function = "i2c0";
> - };
> -
> - i2c1_pins: i2c1 {
> - pins = "PA18", "PA19";
> - function = "i2c1";
> - };
> -
> - i2c2_pins: i2c2 {
> - pins = "PE12", "PE13";
> - function = "i2c2";
> - };
> -
> - mmc0_pins_a: mmc0@0 {
> - pins = "PF0", "PF1", "PF2", "PF3",
> - "PF4", "PF5";
> - function = "mmc0";
> - drive-strength = <30>;
> - bias-pull-up;
> - };
> -
> - mmc0_cd_pin: mmc0_cd_pin@0 {
> - pins = "PF6";
> - function = "gpio_in";
> - bias-pull-up;
> - };
> -
> - mmc1_pins_a: mmc1@0 {
> - pins = "PG0", "PG1", "PG2", "PG3",
> - "PG4", "PG5";
> - function = "mmc1";
> - drive-strength = <30>;
> - bias-pull-up;
> - };
> -
> - mmc2_8bit_pins: mmc2_8bit {
> - pins = "PC5", "PC6", "PC8",
> - "PC9", "PC10", "PC11",
> - "PC12", "PC13", "PC14",
> - "PC15", "PC16";
> - function = "mmc2";
> - drive-strength = <30>;
> - bias-pull-up;
> - };
> -
> - spdif_tx_pins_a: spdif@0 {
> - pins = "PA17";
> - function = "spdif";
> - };
> -
> - spi0_pins: spi0 {
> - pins = "PC0", "PC1", "PC2", "PC3";
> - function = "spi0";
> - };
> -
> - spi1_pins: spi1 {
> - pins = "PA15", "PA16", "PA14", "PA13";
> - function = "spi1";
> - };
> -
> - uart0_pins_a: uart0@0 {
> - pins = "PA4", "PA5";
> - function = "uart0";
> - };
> -
> - uart1_pins: uart1 {
> - pins = "PG6", "PG7";
> - function = "uart1";
> - };
> -
> - uart1_rts_cts_pins: uart1_rts_cts {
> - pins = "PG8", "PG9";
> - function = "uart1";
> - };
> -
> - uart2_pins: uart2 {
> - pins = "PA0", "PA1";
> - function = "uart2";
> - };
> -
> - uart3_pins: uart3 {
> - pins = "PA13", "PA14";
> - function = "uart3";
> - };
> - };
> -
> - timer@01c20c00 {
> - compatible = "allwinner,sun4i-a10-timer";
> - reg = <0x01c20c00 0xa0>;
> - interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&osc24M>;
> - };
> -
> - spi0: spi@01c68000 {
> - compatible = "allwinner,sun8i-h3-spi";
> - reg = <0x01c68000 0x1000>;
> - interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
> - clock-names = "ahb", "mod";
> - dmas = <&dma 23>, <&dma 23>;
> - dma-names = "rx", "tx";
> - pinctrl-names = "default";
> - pinctrl-0 = <&spi0_pins>;
> - resets = <&ccu RST_BUS_SPI0>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - spi1: spi@01c69000 {
> - compatible = "allwinner,sun8i-h3-spi";
> - reg = <0x01c69000 0x1000>;
> - interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
> - clock-names = "ahb", "mod";
> - dmas = <&dma 24>, <&dma 24>;
> - dma-names = "rx", "tx";
> - pinctrl-names = "default";
> - pinctrl-0 = <&spi1_pins>;
> - resets = <&ccu RST_BUS_SPI1>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - wdt0: watchdog@01c20ca0 {
> - compatible = "allwinner,sun6i-a31-wdt";
> - reg = <0x01c20ca0 0x20>;
> - interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> - };
> -
> - spdif: spdif@01c21000 {
> - #sound-dai-cells = <0>;
> - compatible = "allwinner,sun8i-h3-spdif";
> - reg = <0x01c21000 0x400>;
> - interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
> - resets = <&ccu RST_BUS_SPDIF>;
> - clock-names = "apb", "spdif";
> - dmas = <&dma 2>;
> - dma-names = "tx";
> - status = "disabled";
> - };
> -
> - pwm: pwm@01c21400 {
> - compatible = "allwinner,sun8i-h3-pwm";
> - reg = <0x01c21400 0x8>;
> - clocks = <&osc24M>;
> - #pwm-cells = <3>;
> - status = "disabled";
> - };
> -
> - codec: codec@01c22c00 {
> - #sound-dai-cells = <0>;
> - compatible = "allwinner,sun8i-h3-codec";
> - reg = <0x01c22c00 0x400>;
> - interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
> - clock-names = "apb", "codec";
> - resets = <&ccu RST_BUS_CODEC>;
> - dmas = <&dma 15>, <&dma 15>;
> - dma-names = "rx", "tx";
> - allwinner,codec-analog-controls = <&codec_analog>;
> - status = "disabled";
> - };
> -
> - uart0: serial@01c28000 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28000 0x400>;
> - interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART0>;
> - resets = <&ccu RST_BUS_UART0>;
> - dmas = <&dma 6>, <&dma 6>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - uart1: serial@01c28400 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28400 0x400>;
> - interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART1>;
> - resets = <&ccu RST_BUS_UART1>;
> - dmas = <&dma 7>, <&dma 7>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - uart2: serial@01c28800 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28800 0x400>;
> - interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART2>;
> - resets = <&ccu RST_BUS_UART2>;
> - dmas = <&dma 8>, <&dma 8>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - uart3: serial@01c28c00 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28c00 0x400>;
> - interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART3>;
> - resets = <&ccu RST_BUS_UART3>;
> - dmas = <&dma 9>, <&dma 9>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - i2c0: i2c@01c2ac00 {
> - compatible = "allwinner,sun6i-a31-i2c";
> - reg = <0x01c2ac00 0x400>;
> - interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_I2C0>;
> - resets = <&ccu RST_BUS_I2C0>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c0_pins>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - i2c1: i2c@01c2b000 {
> - compatible = "allwinner,sun6i-a31-i2c";
> - reg = <0x01c2b000 0x400>;
> - interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_I2C1>;
> - resets = <&ccu RST_BUS_I2C1>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c1_pins>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - i2c2: i2c@01c2b400 {
> - compatible = "allwinner,sun6i-a31-i2c";
> - reg = <0x01c2b000 0x400>;
> - interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_I2C2>;
> - resets = <&ccu RST_BUS_I2C2>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c2_pins>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - gic: interrupt-controller@01c81000 {
> - compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> - reg = <0x01c81000 0x1000>,
> - <0x01c82000 0x2000>,
> - <0x01c84000 0x2000>,
> - <0x01c86000 0x2000>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> - };
> -
> - rtc: rtc@01f00000 {
> - compatible = "allwinner,sun6i-a31-rtc";
> - reg = <0x01f00000 0x54>;
> - interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> - };
> -
> - apb0_reset: reset@01f014b0 {
> - reg = <0x01f014b0 0x4>;
> - compatible = "allwinner,sun6i-a31-clock-reset";
> - #reset-cells = <1>;
> - };
> -
> - codec_analog: codec-analog@01f015c0 {
> - compatible = "allwinner,sun8i-h3-codec-analog";
> - reg = <0x01f015c0 0x4>;
> - };
> -
> - ir: ir@01f02000 {
> - compatible = "allwinner,sun5i-a13-ir";
> - clocks = <&apb0_gates 1>, <&ir_clk>;
> - clock-names = "apb", "ir";
> - resets = <&apb0_reset 1>;
> - interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> - reg = <0x01f02000 0x40>;
> - status = "disabled";
> - };
> -
> - r_pio: pinctrl@01f02c00 {
> - compatible = "allwinner,sun8i-h3-r-pinctrl";
> - reg = <0x01f02c00 0x400>;
> - interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
> - clock-names = "apb", "hosc", "losc";
> - resets = <&apb0_reset 0>;
> - gpio-controller;
> - #gpio-cells = <3>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> -
> - ir_pins_a: ir@0 {
> - pins = "PL11";
> - function = "s_cir_rx";
> - };
> - };
> - };
> -};
> +/*
> + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "sunxi-h3-h5.dtsi"
> +
> +/ {
> + interrupt-parent = <&gic>;
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu@0 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <0>;
> + };
> +
> + cpu@1 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <1>;
> + };
> +
> + cpu@2 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <2>;
> + };
> +
> + cpu@3 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <3>;
> + };
> + };
> +
> + timer {
> + compatible = "arm,armv7-timer";
> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + soc {
> + gic: interrupt-controller@01c81000 {
> + compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> + reg = <0x01c81000 0x1000>,
> + <0x01c82000 0x2000>,
> + <0x01c84000 0x2000>,
> + <0x01c86000 0x2000>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> + };
> +};
> +
> +&ccu {
> + compatible = "allwinner,sun8i-h3-ccu";
> +};
> +
> +&mmc0 {
> + compatible = "allwinner,sun7i-a20-mmc";
> + clocks = <&ccu CLK_BUS_MMC0>,
> + <&ccu CLK_MMC0>,
> + <&ccu CLK_MMC0_OUTPUT>,
> + <&ccu CLK_MMC0_SAMPLE>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> +};
> +
> +&mmc1 {
> + compatible = "allwinner,sun7i-a20-mmc";
> + clocks = <&ccu CLK_BUS_MMC1>,
> + <&ccu CLK_MMC1>,
> + <&ccu CLK_MMC1_OUTPUT>,
> + <&ccu CLK_MMC1_SAMPLE>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> +};
> +
> +&mmc2 {
> + compatible = "allwinner,sun7i-a20-mmc";
> + clocks = <&ccu CLK_BUS_MMC2>,
> + <&ccu CLK_MMC2>,
> + <&ccu CLK_MMC2_OUTPUT>,
> + <&ccu CLK_MMC2_SAMPLE>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> +};
> +
> +&pio {
> + compatible = "allwinner,sun8i-h3-pinctrl";
> +};
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> similarity index 88%
> copy from arch/arm/boot/dts/sun8i-h3.dtsi
> copy to arch/arm/boot/dts/sunxi-h3-h5.dtsi
> index 8a4d7894a11f..966dc4211c4d 100644
> --- a/arch/arm/boot/dts/sun8i-h3.dtsi
> +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> @@ -40,52 +40,14 @@
> * OTHER DEALINGS IN THE SOFTWARE.
> */
>
> -#include "skeleton.dtsi"
> -
> #include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/pinctrl/sun4i-a10.h>
> #include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
>
> / {
> - interrupt-parent = <&gic>;
> -
> - cpus {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - cpu@0 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <0>;
> - };
> -
> - cpu@1 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <1>;
> - };
> -
> - cpu@2 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <2>;
> - };
> -
> - cpu@3 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <3>;
> - };
> - };
> -
> - timer {
> - compatible = "arm,armv7-timer";
> - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> - };
> + #address-cells = <1>;
> + #size-cells = <1>;
>
> clocks {
> #address-cells = <1>;
> @@ -150,16 +112,8 @@
> };
>
> mmc0: mmc@01c0f000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> + /* compatible and clocks are in per SoC .dtsi file */
> reg = <0x01c0f000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC0>,
> - <&ccu CLK_MMC0>,
> - <&ccu CLK_MMC0_OUTPUT>,
> - <&ccu CLK_MMC0_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> resets = <&ccu RST_BUS_MMC0>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> @@ -169,16 +123,8 @@
> };
>
> mmc1: mmc@01c10000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> + /* compatible and clocks are in per SoC .dtsi file */
> reg = <0x01c10000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC1>,
> - <&ccu CLK_MMC1>,
> - <&ccu CLK_MMC1_OUTPUT>,
> - <&ccu CLK_MMC1_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> resets = <&ccu RST_BUS_MMC1>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> @@ -188,16 +134,8 @@
> };
>
> mmc2: mmc@01c11000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> + /* compatible and clocks are in per SoC .dtsi file */
> reg = <0x01c11000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC2>,
> - <&ccu CLK_MMC2>,
> - <&ccu CLK_MMC2_OUTPUT>,
> - <&ccu CLK_MMC2_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> resets = <&ccu RST_BUS_MMC2>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> @@ -308,7 +246,7 @@
> };
>
> ccu: clock@01c20000 {
> - compatible = "allwinner,sun8i-h3-ccu";
> + /* compatible is in per SoC .dtsi file */
> reg = <0x01c20000 0x400>;
> clocks = <&osc24M>, <&osc32k>;
> clock-names = "hosc", "losc";
> @@ -317,7 +255,7 @@
> };
>
> pio: pinctrl@01c20800 {
> - compatible = "allwinner,sun8i-h3-pinctrl";
> + /* compatible is in per SoC .dtsi file */
> reg = <0x01c20800 0x400>;
> interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> @@ -588,17 +526,6 @@
> #size-cells = <0>;
> };
>
> - gic: interrupt-controller@01c81000 {
> - compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> - reg = <0x01c81000 0x1000>,
> - <0x01c82000 0x2000>,
> - <0x01c84000 0x2000>,
> - <0x01c86000 0x2000>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
The gic bits seem to be the same for both SoCs, aside from the
different compatible
string. Marc had sent a series to change them all to arm,gic-400, which is the
proper name for it, but it wasn't merged. I'm assuming the compatibles
are equal?
If so then it can also be shared.
The rest looks ok.
ChenYu
> - };
> -
> rtc: rtc@01f00000 {
> compatible = "allwinner,sun6i-a31-rtc";
> reg = <0x01f00000 0x54>;
> --
> 2.11.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 62+ messages in thread
* [PATCH v5 5/7] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-02-26 3:46 ` Chen-Yu Tsai
0 siblings, 0 replies; 62+ messages in thread
From: Chen-Yu Tsai @ 2017-02-26 3:46 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On Sun, Feb 26, 2017 at 9:19 AM, Icenowy Zheng <icenowy@aosc.xyz> wrote:
> From: Andre Przywara <andre.przywara@arm.com>
>
> The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
> Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
> updated. So we should really share almost the whole .dtsi.
> In preparation for that move the peripheral parts of the existing
> sun8i-h3.dtsi into a new sun8i-h3-h5.dtsi.
> The actual sun8i-h3.dtsi then includes that and defines the H3 specific
> parts on top of it.
> On the way get rid of skeleton.dtsi, as recommended in that very file.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> [Icenowy: also split out mmc, as well as pio and ccu's compatible]
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> Changes in v3:
> - Use label-based syntax to reference nodes in H3 DTSI file.
> Changes in v2:
> - Rebase on current linux-next (because of the add of audio codec)
>
> arch/arm/boot/dts/sun8i-h3.dtsi | 789 ++++-----------------
> .../boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} | 87 +--
> 2 files changed, 148 insertions(+), 728 deletions(-)
> rewrite arch/arm/boot/dts/sun8i-h3.dtsi (81%)
> copy arch/arm/boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} (88%)
>
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
> dissimilarity index 81%
> index 8a4d7894a11f..4209d974c3f4 100644
> --- a/arch/arm/boot/dts/sun8i-h3.dtsi
> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> @@ -1,648 +1,141 @@
> -/*
> - * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
> - *
> - * This file is dual-licensed: you can use it either under the terms
> - * of the GPL or the X11 license, at your option. Note that this dual
> - * licensing only applies to this file, and not this project as a
> - * whole.
> - *
> - * a) This file is free software; you can redistribute it and/or
> - * modify it under the terms of the GNU General Public License as
> - * published by the Free Software Foundation; either version 2 of the
> - * License, or (at your option) any later version.
> - *
> - * This file is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> - * GNU General Public License for more details.
> - *
> - * Or, alternatively,
> - *
> - * b) Permission is hereby granted, free of charge, to any person
> - * obtaining a copy of this software and associated documentation
> - * files (the "Software"), to deal in the Software without
> - * restriction, including without limitation the rights to use,
> - * copy, modify, merge, publish, distribute, sublicense, and/or
> - * sell copies of the Software, and to permit persons to whom the
> - * Software is furnished to do so, subject to the following
> - * conditions:
> - *
> - * The above copyright notice and this permission notice shall be
> - * included in all copies or substantial portions of the Software.
> - *
> - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> - * OTHER DEALINGS IN THE SOFTWARE.
> - */
> -
> -#include "skeleton.dtsi"
> -
> -#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
> -#include <dt-bindings/interrupt-controller/arm-gic.h>
> -#include <dt-bindings/pinctrl/sun4i-a10.h>
> -#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
> -
> -/ {
> - interrupt-parent = <&gic>;
> -
> - cpus {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - cpu at 0 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <0>;
> - };
> -
> - cpu at 1 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <1>;
> - };
> -
> - cpu at 2 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <2>;
> - };
> -
> - cpu at 3 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <3>;
> - };
> - };
> -
> - timer {
> - compatible = "arm,armv7-timer";
> - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> - };
> -
> - clocks {
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> -
> - osc24M: osc24M_clk {
> - #clock-cells = <0>;
> - compatible = "fixed-clock";
> - clock-frequency = <24000000>;
> - clock-output-names = "osc24M";
> - };
> -
> - osc32k: osc32k_clk {
> - #clock-cells = <0>;
> - compatible = "fixed-clock";
> - clock-frequency = <32768>;
> - clock-output-names = "osc32k";
> - };
> -
> - apb0: apb0_clk {
> - compatible = "fixed-factor-clock";
> - #clock-cells = <0>;
> - clock-div = <1>;
> - clock-mult = <1>;
> - clocks = <&osc24M>;
> - clock-output-names = "apb0";
> - };
> -
> - apb0_gates: clk at 01f01428 {
> - compatible = "allwinner,sun8i-h3-apb0-gates-clk",
> - "allwinner,sun4i-a10-gates-clk";
> - reg = <0x01f01428 0x4>;
> - #clock-cells = <1>;
> - clocks = <&apb0>;
> - clock-indices = <0>, <1>;
> - clock-output-names = "apb0_pio", "apb0_ir";
> - };
> -
> - ir_clk: ir_clk at 01f01454 {
> - compatible = "allwinner,sun4i-a10-mod0-clk";
> - reg = <0x01f01454 0x4>;
> - #clock-cells = <0>;
> - clocks = <&osc32k>, <&osc24M>;
> - clock-output-names = "ir";
> - };
> - };
> -
> - soc {
> - compatible = "simple-bus";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> -
> - dma: dma-controller at 01c02000 {
> - compatible = "allwinner,sun8i-h3-dma";
> - reg = <0x01c02000 0x1000>;
> - interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_DMA>;
> - resets = <&ccu RST_BUS_DMA>;
> - #dma-cells = <1>;
> - };
> -
> - mmc0: mmc at 01c0f000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> - reg = <0x01c0f000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC0>,
> - <&ccu CLK_MMC0>,
> - <&ccu CLK_MMC0_OUTPUT>,
> - <&ccu CLK_MMC0_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> - resets = <&ccu RST_BUS_MMC0>;
> - reset-names = "ahb";
> - interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - mmc1: mmc at 01c10000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> - reg = <0x01c10000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC1>,
> - <&ccu CLK_MMC1>,
> - <&ccu CLK_MMC1_OUTPUT>,
> - <&ccu CLK_MMC1_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> - resets = <&ccu RST_BUS_MMC1>;
> - reset-names = "ahb";
> - interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - mmc2: mmc at 01c11000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> - reg = <0x01c11000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC2>,
> - <&ccu CLK_MMC2>,
> - <&ccu CLK_MMC2_OUTPUT>,
> - <&ccu CLK_MMC2_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> - resets = <&ccu RST_BUS_MMC2>;
> - reset-names = "ahb";
> - interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - usbphy: phy at 01c19400 {
> - compatible = "allwinner,sun8i-h3-usb-phy";
> - reg = <0x01c19400 0x2c>,
> - <0x01c1a800 0x4>,
> - <0x01c1b800 0x4>,
> - <0x01c1c800 0x4>,
> - <0x01c1d800 0x4>;
> - reg-names = "phy_ctrl",
> - "pmu0",
> - "pmu1",
> - "pmu2",
> - "pmu3";
> - clocks = <&ccu CLK_USB_PHY0>,
> - <&ccu CLK_USB_PHY1>,
> - <&ccu CLK_USB_PHY2>,
> - <&ccu CLK_USB_PHY3>;
> - clock-names = "usb0_phy",
> - "usb1_phy",
> - "usb2_phy",
> - "usb3_phy";
> - resets = <&ccu RST_USB_PHY0>,
> - <&ccu RST_USB_PHY1>,
> - <&ccu RST_USB_PHY2>,
> - <&ccu RST_USB_PHY3>;
> - reset-names = "usb0_reset",
> - "usb1_reset",
> - "usb2_reset",
> - "usb3_reset";
> - status = "disabled";
> - #phy-cells = <1>;
> - };
> -
> - ehci1: usb at 01c1b000 {
> - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> - reg = <0x01c1b000 0x100>;
> - interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
> - resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
> - phys = <&usbphy 1>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ohci1: usb at 01c1b400 {
> - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> - reg = <0x01c1b400 0x100>;
> - interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
> - <&ccu CLK_USB_OHCI1>;
> - resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
> - phys = <&usbphy 1>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ehci2: usb at 01c1c000 {
> - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> - reg = <0x01c1c000 0x100>;
> - interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
> - resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
> - phys = <&usbphy 2>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ohci2: usb at 01c1c400 {
> - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> - reg = <0x01c1c400 0x100>;
> - interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
> - <&ccu CLK_USB_OHCI2>;
> - resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
> - phys = <&usbphy 2>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ehci3: usb at 01c1d000 {
> - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> - reg = <0x01c1d000 0x100>;
> - interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
> - resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
> - phys = <&usbphy 3>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ohci3: usb at 01c1d400 {
> - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> - reg = <0x01c1d400 0x100>;
> - interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
> - <&ccu CLK_USB_OHCI3>;
> - resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
> - phys = <&usbphy 3>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ccu: clock at 01c20000 {
> - compatible = "allwinner,sun8i-h3-ccu";
> - reg = <0x01c20000 0x400>;
> - clocks = <&osc24M>, <&osc32k>;
> - clock-names = "hosc", "losc";
> - #clock-cells = <1>;
> - #reset-cells = <1>;
> - };
> -
> - pio: pinctrl at 01c20800 {
> - compatible = "allwinner,sun8i-h3-pinctrl";
> - reg = <0x01c20800 0x400>;
> - interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
> - clock-names = "apb", "hosc", "losc";
> - gpio-controller;
> - #gpio-cells = <3>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> -
> - i2c0_pins: i2c0 {
> - pins = "PA11", "PA12";
> - function = "i2c0";
> - };
> -
> - i2c1_pins: i2c1 {
> - pins = "PA18", "PA19";
> - function = "i2c1";
> - };
> -
> - i2c2_pins: i2c2 {
> - pins = "PE12", "PE13";
> - function = "i2c2";
> - };
> -
> - mmc0_pins_a: mmc0 at 0 {
> - pins = "PF0", "PF1", "PF2", "PF3",
> - "PF4", "PF5";
> - function = "mmc0";
> - drive-strength = <30>;
> - bias-pull-up;
> - };
> -
> - mmc0_cd_pin: mmc0_cd_pin at 0 {
> - pins = "PF6";
> - function = "gpio_in";
> - bias-pull-up;
> - };
> -
> - mmc1_pins_a: mmc1 at 0 {
> - pins = "PG0", "PG1", "PG2", "PG3",
> - "PG4", "PG5";
> - function = "mmc1";
> - drive-strength = <30>;
> - bias-pull-up;
> - };
> -
> - mmc2_8bit_pins: mmc2_8bit {
> - pins = "PC5", "PC6", "PC8",
> - "PC9", "PC10", "PC11",
> - "PC12", "PC13", "PC14",
> - "PC15", "PC16";
> - function = "mmc2";
> - drive-strength = <30>;
> - bias-pull-up;
> - };
> -
> - spdif_tx_pins_a: spdif at 0 {
> - pins = "PA17";
> - function = "spdif";
> - };
> -
> - spi0_pins: spi0 {
> - pins = "PC0", "PC1", "PC2", "PC3";
> - function = "spi0";
> - };
> -
> - spi1_pins: spi1 {
> - pins = "PA15", "PA16", "PA14", "PA13";
> - function = "spi1";
> - };
> -
> - uart0_pins_a: uart0 at 0 {
> - pins = "PA4", "PA5";
> - function = "uart0";
> - };
> -
> - uart1_pins: uart1 {
> - pins = "PG6", "PG7";
> - function = "uart1";
> - };
> -
> - uart1_rts_cts_pins: uart1_rts_cts {
> - pins = "PG8", "PG9";
> - function = "uart1";
> - };
> -
> - uart2_pins: uart2 {
> - pins = "PA0", "PA1";
> - function = "uart2";
> - };
> -
> - uart3_pins: uart3 {
> - pins = "PA13", "PA14";
> - function = "uart3";
> - };
> - };
> -
> - timer at 01c20c00 {
> - compatible = "allwinner,sun4i-a10-timer";
> - reg = <0x01c20c00 0xa0>;
> - interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&osc24M>;
> - };
> -
> - spi0: spi at 01c68000 {
> - compatible = "allwinner,sun8i-h3-spi";
> - reg = <0x01c68000 0x1000>;
> - interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
> - clock-names = "ahb", "mod";
> - dmas = <&dma 23>, <&dma 23>;
> - dma-names = "rx", "tx";
> - pinctrl-names = "default";
> - pinctrl-0 = <&spi0_pins>;
> - resets = <&ccu RST_BUS_SPI0>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - spi1: spi at 01c69000 {
> - compatible = "allwinner,sun8i-h3-spi";
> - reg = <0x01c69000 0x1000>;
> - interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
> - clock-names = "ahb", "mod";
> - dmas = <&dma 24>, <&dma 24>;
> - dma-names = "rx", "tx";
> - pinctrl-names = "default";
> - pinctrl-0 = <&spi1_pins>;
> - resets = <&ccu RST_BUS_SPI1>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - wdt0: watchdog at 01c20ca0 {
> - compatible = "allwinner,sun6i-a31-wdt";
> - reg = <0x01c20ca0 0x20>;
> - interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> - };
> -
> - spdif: spdif at 01c21000 {
> - #sound-dai-cells = <0>;
> - compatible = "allwinner,sun8i-h3-spdif";
> - reg = <0x01c21000 0x400>;
> - interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
> - resets = <&ccu RST_BUS_SPDIF>;
> - clock-names = "apb", "spdif";
> - dmas = <&dma 2>;
> - dma-names = "tx";
> - status = "disabled";
> - };
> -
> - pwm: pwm at 01c21400 {
> - compatible = "allwinner,sun8i-h3-pwm";
> - reg = <0x01c21400 0x8>;
> - clocks = <&osc24M>;
> - #pwm-cells = <3>;
> - status = "disabled";
> - };
> -
> - codec: codec at 01c22c00 {
> - #sound-dai-cells = <0>;
> - compatible = "allwinner,sun8i-h3-codec";
> - reg = <0x01c22c00 0x400>;
> - interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
> - clock-names = "apb", "codec";
> - resets = <&ccu RST_BUS_CODEC>;
> - dmas = <&dma 15>, <&dma 15>;
> - dma-names = "rx", "tx";
> - allwinner,codec-analog-controls = <&codec_analog>;
> - status = "disabled";
> - };
> -
> - uart0: serial at 01c28000 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28000 0x400>;
> - interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART0>;
> - resets = <&ccu RST_BUS_UART0>;
> - dmas = <&dma 6>, <&dma 6>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - uart1: serial at 01c28400 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28400 0x400>;
> - interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART1>;
> - resets = <&ccu RST_BUS_UART1>;
> - dmas = <&dma 7>, <&dma 7>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - uart2: serial at 01c28800 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28800 0x400>;
> - interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART2>;
> - resets = <&ccu RST_BUS_UART2>;
> - dmas = <&dma 8>, <&dma 8>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - uart3: serial at 01c28c00 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28c00 0x400>;
> - interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART3>;
> - resets = <&ccu RST_BUS_UART3>;
> - dmas = <&dma 9>, <&dma 9>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - i2c0: i2c at 01c2ac00 {
> - compatible = "allwinner,sun6i-a31-i2c";
> - reg = <0x01c2ac00 0x400>;
> - interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_I2C0>;
> - resets = <&ccu RST_BUS_I2C0>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c0_pins>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - i2c1: i2c at 01c2b000 {
> - compatible = "allwinner,sun6i-a31-i2c";
> - reg = <0x01c2b000 0x400>;
> - interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_I2C1>;
> - resets = <&ccu RST_BUS_I2C1>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c1_pins>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - i2c2: i2c at 01c2b400 {
> - compatible = "allwinner,sun6i-a31-i2c";
> - reg = <0x01c2b000 0x400>;
> - interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_I2C2>;
> - resets = <&ccu RST_BUS_I2C2>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c2_pins>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - gic: interrupt-controller at 01c81000 {
> - compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> - reg = <0x01c81000 0x1000>,
> - <0x01c82000 0x2000>,
> - <0x01c84000 0x2000>,
> - <0x01c86000 0x2000>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> - };
> -
> - rtc: rtc at 01f00000 {
> - compatible = "allwinner,sun6i-a31-rtc";
> - reg = <0x01f00000 0x54>;
> - interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> - };
> -
> - apb0_reset: reset at 01f014b0 {
> - reg = <0x01f014b0 0x4>;
> - compatible = "allwinner,sun6i-a31-clock-reset";
> - #reset-cells = <1>;
> - };
> -
> - codec_analog: codec-analog at 01f015c0 {
> - compatible = "allwinner,sun8i-h3-codec-analog";
> - reg = <0x01f015c0 0x4>;
> - };
> -
> - ir: ir at 01f02000 {
> - compatible = "allwinner,sun5i-a13-ir";
> - clocks = <&apb0_gates 1>, <&ir_clk>;
> - clock-names = "apb", "ir";
> - resets = <&apb0_reset 1>;
> - interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> - reg = <0x01f02000 0x40>;
> - status = "disabled";
> - };
> -
> - r_pio: pinctrl at 01f02c00 {
> - compatible = "allwinner,sun8i-h3-r-pinctrl";
> - reg = <0x01f02c00 0x400>;
> - interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
> - clock-names = "apb", "hosc", "losc";
> - resets = <&apb0_reset 0>;
> - gpio-controller;
> - #gpio-cells = <3>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> -
> - ir_pins_a: ir at 0 {
> - pins = "PL11";
> - function = "s_cir_rx";
> - };
> - };
> - };
> -};
> +/*
> + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "sunxi-h3-h5.dtsi"
> +
> +/ {
> + interrupt-parent = <&gic>;
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu at 0 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <0>;
> + };
> +
> + cpu at 1 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <1>;
> + };
> +
> + cpu at 2 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <2>;
> + };
> +
> + cpu at 3 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <3>;
> + };
> + };
> +
> + timer {
> + compatible = "arm,armv7-timer";
> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + soc {
> + gic: interrupt-controller at 01c81000 {
> + compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> + reg = <0x01c81000 0x1000>,
> + <0x01c82000 0x2000>,
> + <0x01c84000 0x2000>,
> + <0x01c86000 0x2000>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> + };
> +};
> +
> +&ccu {
> + compatible = "allwinner,sun8i-h3-ccu";
> +};
> +
> +&mmc0 {
> + compatible = "allwinner,sun7i-a20-mmc";
> + clocks = <&ccu CLK_BUS_MMC0>,
> + <&ccu CLK_MMC0>,
> + <&ccu CLK_MMC0_OUTPUT>,
> + <&ccu CLK_MMC0_SAMPLE>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> +};
> +
> +&mmc1 {
> + compatible = "allwinner,sun7i-a20-mmc";
> + clocks = <&ccu CLK_BUS_MMC1>,
> + <&ccu CLK_MMC1>,
> + <&ccu CLK_MMC1_OUTPUT>,
> + <&ccu CLK_MMC1_SAMPLE>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> +};
> +
> +&mmc2 {
> + compatible = "allwinner,sun7i-a20-mmc";
> + clocks = <&ccu CLK_BUS_MMC2>,
> + <&ccu CLK_MMC2>,
> + <&ccu CLK_MMC2_OUTPUT>,
> + <&ccu CLK_MMC2_SAMPLE>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> +};
> +
> +&pio {
> + compatible = "allwinner,sun8i-h3-pinctrl";
> +};
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> similarity index 88%
> copy from arch/arm/boot/dts/sun8i-h3.dtsi
> copy to arch/arm/boot/dts/sunxi-h3-h5.dtsi
> index 8a4d7894a11f..966dc4211c4d 100644
> --- a/arch/arm/boot/dts/sun8i-h3.dtsi
> +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> @@ -40,52 +40,14 @@
> * OTHER DEALINGS IN THE SOFTWARE.
> */
>
> -#include "skeleton.dtsi"
> -
> #include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/pinctrl/sun4i-a10.h>
> #include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
>
> / {
> - interrupt-parent = <&gic>;
> -
> - cpus {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - cpu at 0 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <0>;
> - };
> -
> - cpu at 1 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <1>;
> - };
> -
> - cpu at 2 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <2>;
> - };
> -
> - cpu at 3 {
> - compatible = "arm,cortex-a7";
> - device_type = "cpu";
> - reg = <3>;
> - };
> - };
> -
> - timer {
> - compatible = "arm,armv7-timer";
> - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> - <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> - };
> + #address-cells = <1>;
> + #size-cells = <1>;
>
> clocks {
> #address-cells = <1>;
> @@ -150,16 +112,8 @@
> };
>
> mmc0: mmc at 01c0f000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> + /* compatible and clocks are in per SoC .dtsi file */
> reg = <0x01c0f000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC0>,
> - <&ccu CLK_MMC0>,
> - <&ccu CLK_MMC0_OUTPUT>,
> - <&ccu CLK_MMC0_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> resets = <&ccu RST_BUS_MMC0>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> @@ -169,16 +123,8 @@
> };
>
> mmc1: mmc at 01c10000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> + /* compatible and clocks are in per SoC .dtsi file */
> reg = <0x01c10000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC1>,
> - <&ccu CLK_MMC1>,
> - <&ccu CLK_MMC1_OUTPUT>,
> - <&ccu CLK_MMC1_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> resets = <&ccu RST_BUS_MMC1>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> @@ -188,16 +134,8 @@
> };
>
> mmc2: mmc at 01c11000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> + /* compatible and clocks are in per SoC .dtsi file */
> reg = <0x01c11000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC2>,
> - <&ccu CLK_MMC2>,
> - <&ccu CLK_MMC2_OUTPUT>,
> - <&ccu CLK_MMC2_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> resets = <&ccu RST_BUS_MMC2>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> @@ -308,7 +246,7 @@
> };
>
> ccu: clock at 01c20000 {
> - compatible = "allwinner,sun8i-h3-ccu";
> + /* compatible is in per SoC .dtsi file */
> reg = <0x01c20000 0x400>;
> clocks = <&osc24M>, <&osc32k>;
> clock-names = "hosc", "losc";
> @@ -317,7 +255,7 @@
> };
>
> pio: pinctrl at 01c20800 {
> - compatible = "allwinner,sun8i-h3-pinctrl";
> + /* compatible is in per SoC .dtsi file */
> reg = <0x01c20800 0x400>;
> interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> @@ -588,17 +526,6 @@
> #size-cells = <0>;
> };
>
> - gic: interrupt-controller at 01c81000 {
> - compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> - reg = <0x01c81000 0x1000>,
> - <0x01c82000 0x2000>,
> - <0x01c84000 0x2000>,
> - <0x01c86000 0x2000>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
The gic bits seem to be the same for both SoCs, aside from the
different compatible
string. Marc had sent a series to change them all to arm,gic-400, which is the
proper name for it, but it wasn't merged. I'm assuming the compatibles
are equal?
If so then it can also be shared.
The rest looks ok.
ChenYu
> - };
> -
> rtc: rtc at 01f00000 {
> compatible = "allwinner,sun6i-a31-rtc";
> reg = <0x01f00000 0x54>;
> --
> 2.11.1
>
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 6/7] arm64: dts: allwinner: add Allwinner H5 .dtsi
2017-02-26 1:19 ` Icenowy Zheng
(?)
(?)
@ 2017-02-26 8:55 ` Rask Ingemann Lambertsen
-1 siblings, 0 replies; 62+ messages in thread
From: Rask Ingemann Lambertsen @ 2017-02-26 8:55 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara, devicetree, linux-kernel,
linux-sunxi, linux-clk, linux-arm-kernel
On Sun, Feb 26, 2017 at 09:19:55AM +0800, Icenowy Zheng wrote:
> From: Andre Przywara <andre.przywara@arm.com>
>
> The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
> Cortex-A53 cores instead.
> Based on the now shared base .dtsi describing the common peripherals
> describe the H5 specific nodes on top of that.
> That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> [Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
> refactor, commit message change to met new arm64 naming scheme,
s/change to met/change to meet/ or s/change to met/changed to meet/ ?
> diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
> new file mode 120000
> index 000000000000..036f01dc2b9b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
> @@ -0,0 +1 @@
> +../../../../arm/boot/dts/sunxi-h3-h5.dtsi
> \ No newline at end of file
But it's missing more than just a newline, isn't it? Shouldn't it read
#include <../../../../arm/boot/dts/sunxi-h3-h5.dtsi>
?
--
Rask Ingemann Lambertsen
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 6/7] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-02-26 8:55 ` Rask Ingemann Lambertsen
0 siblings, 0 replies; 62+ messages in thread
From: Rask Ingemann Lambertsen @ 2017-02-26 8:55 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, Catalin Marinas, linux-sunxi, Will Deacon,
linux-kernel, Chen-Yu Tsai, Rob Herring, Andre Przywara,
Maxime Ripard, linux-clk, linux-arm-kernel
On Sun, Feb 26, 2017 at 09:19:55AM +0800, Icenowy Zheng wrote:
> From: Andre Przywara <andre.przywara@arm.com>
>
> The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
> Cortex-A53 cores instead.
> Based on the now shared base .dtsi describing the common peripherals
> describe the H5 specific nodes on top of that.
> That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> [Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
> refactor, commit message change to met new arm64 naming scheme,
s/change to met/change to meet/ or s/change to met/changed to meet/ ?
> diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
> new file mode 120000
> index 000000000000..036f01dc2b9b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
> @@ -0,0 +1 @@
> +../../../../arm/boot/dts/sunxi-h3-h5.dtsi
> \ No newline at end of file
But it's missing more than just a newline, isn't it? Shouldn't it read
#include <../../../../arm/boot/dts/sunxi-h3-h5.dtsi>
?
--
Rask Ingemann Lambertsen
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 6/7] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-02-26 8:55 ` Rask Ingemann Lambertsen
0 siblings, 0 replies; 62+ messages in thread
From: Rask Ingemann Lambertsen @ 2017-02-26 8:55 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, Catalin Marinas, linux-sunxi, Will Deacon,
linux-kernel, Chen-Yu Tsai, Rob Herring, Andre Przywara,
Maxime Ripard, linux-clk, linux-arm-kernel
On Sun, Feb 26, 2017 at 09:19:55AM +0800, Icenowy Zheng wrote:
> From: Andre Przywara <andre.przywara@arm.com>
>
> The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
> Cortex-A53 cores instead.
> Based on the now shared base .dtsi describing the common peripherals
> describe the H5 specific nodes on top of that.
> That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> [Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
> refactor, commit message change to met new arm64 naming scheme,
s/change to met/change to meet/ or s/change to met/changed to meet/ ?
> diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
> new file mode 120000
> index 000000000000..036f01dc2b9b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
> @@ -0,0 +1 @@
> +../../../../arm/boot/dts/sunxi-h3-h5.dtsi
> \ No newline at end of file
But it's missing more than just a newline, isn't it? Shouldn't it read
#include <../../../../arm/boot/dts/sunxi-h3-h5.dtsi>
?
--
Rask Ingemann Lambertsen
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 62+ messages in thread
* [PATCH v5 6/7] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-02-26 8:55 ` Rask Ingemann Lambertsen
0 siblings, 0 replies; 62+ messages in thread
From: Rask Ingemann Lambertsen @ 2017-02-26 8:55 UTC (permalink / raw)
To: linux-arm-kernel
On Sun, Feb 26, 2017 at 09:19:55AM +0800, Icenowy Zheng wrote:
> From: Andre Przywara <andre.przywara@arm.com>
>
> The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
> Cortex-A53 cores instead.
> Based on the now shared base .dtsi describing the common peripherals
> describe the H5 specific nodes on top of that.
> That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> [Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
> refactor, commit message change to met new arm64 naming scheme,
s/change to met/change to meet/ or s/change to met/changed to meet/ ?
> diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
> new file mode 120000
> index 000000000000..036f01dc2b9b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
> @@ -0,0 +1 @@
> +../../../../arm/boot/dts/sunxi-h3-h5.dtsi
> \ No newline at end of file
But it's missing more than just a newline, isn't it? Shouldn't it read
#include <../../../../arm/boot/dts/sunxi-h3-h5.dtsi>
?
--
Rask Ingemann Lambertsen
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 6/7] arm64: dts: allwinner: add Allwinner H5 .dtsi
2017-02-26 8:55 ` Rask Ingemann Lambertsen
(?)
(?)
@ 2017-02-26 9:00 ` Chen-Yu Tsai
-1 siblings, 0 replies; 62+ messages in thread
From: Chen-Yu Tsai @ 2017-02-26 9:00 UTC (permalink / raw)
To: Rask Ingemann Lambertsen
Cc: Icenowy Zheng, Rob Herring, Maxime Ripard, Chen-Yu Tsai,
Catalin Marinas, Will Deacon, Andre Przywara, devicetree,
linux-kernel, linux-sunxi, linux-clk, linux-arm-kernel
On Sun, Feb 26, 2017 at 4:55 PM, Rask Ingemann Lambertsen
<rask@formelder.dk> wrote:
> On Sun, Feb 26, 2017 at 09:19:55AM +0800, Icenowy Zheng wrote:
>> From: Andre Przywara <andre.przywara@arm.com>
>>
>> The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
>> Cortex-A53 cores instead.
>> Based on the now shared base .dtsi describing the common peripherals
>> describe the H5 specific nodes on top of that.
>> That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
>>
>> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
>> [Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
>> refactor, commit message change to met new arm64 naming scheme,
>
> s/change to met/change to meet/ or s/change to met/changed to meet/ ?
>
>> diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
>> new file mode 120000
>> index 000000000000..036f01dc2b9b
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
>> @@ -0,0 +1 @@
>> +../../../../arm/boot/dts/sunxi-h3-h5.dtsi
>> \ No newline at end of file
>
> But it's missing more than just a newline, isn't it? Shouldn't it read
This is a symbolic link.
>
> #include <../../../../arm/boot/dts/sunxi-h3-h5.dtsi>
This won't work directly with the split out device tree repository,
which has a slightly different layout.
ChenYu
>
> ?
>
> --
> Rask Ingemann Lambertsen
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 6/7] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-02-26 9:00 ` Chen-Yu Tsai
0 siblings, 0 replies; 62+ messages in thread
From: Chen-Yu Tsai @ 2017-02-26 9:00 UTC (permalink / raw)
To: Rask Ingemann Lambertsen
Cc: Icenowy Zheng, Rob Herring, Maxime Ripard, Chen-Yu Tsai,
Catalin Marinas, Will Deacon, Andre Przywara, devicetree,
linux-kernel, linux-sunxi, linux-clk, linux-arm-kernel
On Sun, Feb 26, 2017 at 4:55 PM, Rask Ingemann Lambertsen
<rask-SivP7zSAdNDZaaYASwVUlg@public.gmane.org> wrote:
> On Sun, Feb 26, 2017 at 09:19:55AM +0800, Icenowy Zheng wrote:
>> From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
>>
>> The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
>> Cortex-A53 cores instead.
>> Based on the now shared base .dtsi describing the common peripherals
>> describe the H5 specific nodes on top of that.
>> That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
>>
>> Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
>> [Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
>> refactor, commit message change to met new arm64 naming scheme,
>
> s/change to met/change to meet/ or s/change to met/changed to meet/ ?
>
>> diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
>> new file mode 120000
>> index 000000000000..036f01dc2b9b
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
>> @@ -0,0 +1 @@
>> +../../../../arm/boot/dts/sunxi-h3-h5.dtsi
>> \ No newline at end of file
>
> But it's missing more than just a newline, isn't it? Shouldn't it read
This is a symbolic link.
>
> #include <../../../../arm/boot/dts/sunxi-h3-h5.dtsi>
This won't work directly with the split out device tree repository,
which has a slightly different layout.
ChenYu
>
> ?
>
> --
> Rask Ingemann Lambertsen
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 6/7] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-02-26 9:00 ` Chen-Yu Tsai
0 siblings, 0 replies; 62+ messages in thread
From: Chen-Yu Tsai @ 2017-02-26 9:00 UTC (permalink / raw)
To: Rask Ingemann Lambertsen
Cc: devicetree, Catalin Marinas, linux-sunxi, Will Deacon,
linux-kernel, Chen-Yu Tsai, Rob Herring, Icenowy Zheng,
Andre Przywara, Maxime Ripard, linux-clk, linux-arm-kernel
On Sun, Feb 26, 2017 at 4:55 PM, Rask Ingemann Lambertsen
<rask@formelder.dk> wrote:
> On Sun, Feb 26, 2017 at 09:19:55AM +0800, Icenowy Zheng wrote:
>> From: Andre Przywara <andre.przywara@arm.com>
>>
>> The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
>> Cortex-A53 cores instead.
>> Based on the now shared base .dtsi describing the common peripherals
>> describe the H5 specific nodes on top of that.
>> That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
>>
>> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
>> [Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
>> refactor, commit message change to met new arm64 naming scheme,
>
> s/change to met/change to meet/ or s/change to met/changed to meet/ ?
>
>> diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
>> new file mode 120000
>> index 000000000000..036f01dc2b9b
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
>> @@ -0,0 +1 @@
>> +../../../../arm/boot/dts/sunxi-h3-h5.dtsi
>> \ No newline at end of file
>
> But it's missing more than just a newline, isn't it? Shouldn't it read
This is a symbolic link.
>
> #include <../../../../arm/boot/dts/sunxi-h3-h5.dtsi>
This won't work directly with the split out device tree repository,
which has a slightly different layout.
ChenYu
>
> ?
>
> --
> Rask Ingemann Lambertsen
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 62+ messages in thread
* [PATCH v5 6/7] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-02-26 9:00 ` Chen-Yu Tsai
0 siblings, 0 replies; 62+ messages in thread
From: Chen-Yu Tsai @ 2017-02-26 9:00 UTC (permalink / raw)
To: linux-arm-kernel
On Sun, Feb 26, 2017 at 4:55 PM, Rask Ingemann Lambertsen
<rask@formelder.dk> wrote:
> On Sun, Feb 26, 2017 at 09:19:55AM +0800, Icenowy Zheng wrote:
>> From: Andre Przywara <andre.przywara@arm.com>
>>
>> The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
>> Cortex-A53 cores instead.
>> Based on the now shared base .dtsi describing the common peripherals
>> describe the H5 specific nodes on top of that.
>> That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
>>
>> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
>> [Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
>> refactor, commit message change to met new arm64 naming scheme,
>
> s/change to met/change to meet/ or s/change to met/changed to meet/ ?
>
>> diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
>> new file mode 120000
>> index 000000000000..036f01dc2b9b
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
>> @@ -0,0 +1 @@
>> +../../../../arm/boot/dts/sunxi-h3-h5.dtsi
>> \ No newline at end of file
>
> But it's missing more than just a newline, isn't it? Shouldn't it read
This is a symbolic link.
>
> #include <../../../../arm/boot/dts/sunxi-h3-h5.dtsi>
This won't work directly with the split out device tree repository,
which has a slightly different layout.
ChenYu
>
> ?
>
> --
> Rask Ingemann Lambertsen
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 7/7] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
2017-02-26 1:19 ` Icenowy Zheng
(?)
(?)
@ 2017-02-26 9:19 ` Rask Ingemann Lambertsen
-1 siblings, 0 replies; 62+ messages in thread
From: Rask Ingemann Lambertsen @ 2017-02-26 9:19 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara, devicetree, linux-kernel,
linux-sunxi, linux-clk, linux-arm-kernel
On Sun, Feb 26, 2017 at 09:19:56AM +0800, Icenowy Zheng wrote:
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
> new file mode 100644
> index 000000000000..79784cba806c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
[...]
> + leds {
> + compatible = "gpio-leds";
> +
> + pwr_led {
> + label = "orangepi:green:pwr";
> + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
> + default-state = "on";
> + };
> +
> + status_led {
IMHO, you don't need the '_led' suffix inside the 'leds' node, and then you
also avoid having underscores in the node names.
> + label = "orangepi:red:status";
> + gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + r_gpio_keys {
Node names should not contain underscores. You can use hyphens instead. See
https://www.mail-archive.com/linux-kernel%40vger.kernel.org/msg1122967.html
https://www.mail-archive.com/linux-kernel%40vger.kernel.org/msg1145633.html
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
> + vmmc-supply = <®_vcc3v3>;
> + bus-width = <4>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
> + cd-inverted;
You should be able to simplify those last two lines to just
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
(see the paragraph which begins with "*NOTE* on CD and WP polarity."
in 'Documentation/devicetree/bindings/mmc/mmc.txt'.)
--
Rask Ingemann Lambertsen
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 7/7] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
@ 2017-02-26 9:19 ` Rask Ingemann Lambertsen
0 siblings, 0 replies; 62+ messages in thread
From: Rask Ingemann Lambertsen @ 2017-02-26 9:19 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, Catalin Marinas, linux-sunxi, Will Deacon,
linux-kernel, Chen-Yu Tsai, Rob Herring, Andre Przywara,
Maxime Ripard, linux-clk, linux-arm-kernel
On Sun, Feb 26, 2017 at 09:19:56AM +0800, Icenowy Zheng wrote:
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
> new file mode 100644
> index 000000000000..79784cba806c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
[...]
> + leds {
> + compatible = "gpio-leds";
> +
> + pwr_led {
> + label = "orangepi:green:pwr";
> + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
> + default-state = "on";
> + };
> +
> + status_led {
IMHO, you don't need the '_led' suffix inside the 'leds' node, and then you
also avoid having underscores in the node names.
> + label = "orangepi:red:status";
> + gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + r_gpio_keys {
Node names should not contain underscores. You can use hyphens instead. See
https://www.mail-archive.com/linux-kernel%40vger.kernel.org/msg1122967.html
https://www.mail-archive.com/linux-kernel%40vger.kernel.org/msg1145633.html
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
> + vmmc-supply = <®_vcc3v3>;
> + bus-width = <4>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
> + cd-inverted;
You should be able to simplify those last two lines to just
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
(see the paragraph which begins with "*NOTE* on CD and WP polarity."
in 'Documentation/devicetree/bindings/mmc/mmc.txt'.)
--
Rask Ingemann Lambertsen
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 7/7] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
@ 2017-02-26 9:19 ` Rask Ingemann Lambertsen
0 siblings, 0 replies; 62+ messages in thread
From: Rask Ingemann Lambertsen @ 2017-02-26 9:19 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, Catalin Marinas, linux-sunxi, Will Deacon,
linux-kernel, Chen-Yu Tsai, Rob Herring, Andre Przywara,
Maxime Ripard, linux-clk, linux-arm-kernel
On Sun, Feb 26, 2017 at 09:19:56AM +0800, Icenowy Zheng wrote:
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
> new file mode 100644
> index 000000000000..79784cba806c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
[...]
> + leds {
> + compatible = "gpio-leds";
> +
> + pwr_led {
> + label = "orangepi:green:pwr";
> + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
> + default-state = "on";
> + };
> +
> + status_led {
IMHO, you don't need the '_led' suffix inside the 'leds' node, and then you
also avoid having underscores in the node names.
> + label = "orangepi:red:status";
> + gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + r_gpio_keys {
Node names should not contain underscores. You can use hyphens instead. See
https://www.mail-archive.com/linux-kernel%40vger.kernel.org/msg1122967.html
https://www.mail-archive.com/linux-kernel%40vger.kernel.org/msg1145633.html
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
> + vmmc-supply = <®_vcc3v3>;
> + bus-width = <4>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
> + cd-inverted;
You should be able to simplify those last two lines to just
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
(see the paragraph which begins with "*NOTE* on CD and WP polarity."
in 'Documentation/devicetree/bindings/mmc/mmc.txt'.)
--
Rask Ingemann Lambertsen
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 62+ messages in thread
* [PATCH v5 7/7] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
@ 2017-02-26 9:19 ` Rask Ingemann Lambertsen
0 siblings, 0 replies; 62+ messages in thread
From: Rask Ingemann Lambertsen @ 2017-02-26 9:19 UTC (permalink / raw)
To: linux-arm-kernel
On Sun, Feb 26, 2017 at 09:19:56AM +0800, Icenowy Zheng wrote:
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
> new file mode 100644
> index 000000000000..79784cba806c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
[...]
> + leds {
> + compatible = "gpio-leds";
> +
> + pwr_led {
> + label = "orangepi:green:pwr";
> + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
> + default-state = "on";
> + };
> +
> + status_led {
IMHO, you don't need the '_led' suffix inside the 'leds' node, and then you
also avoid having underscores in the node names.
> + label = "orangepi:red:status";
> + gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + r_gpio_keys {
Node names should not contain underscores. You can use hyphens instead. See
https://www.mail-archive.com/linux-kernel%40vger.kernel.org/msg1122967.html
https://www.mail-archive.com/linux-kernel%40vger.kernel.org/msg1145633.html
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
> + vmmc-supply = <®_vcc3v3>;
> + bus-width = <4>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
> + cd-inverted;
You should be able to simplify those last two lines to just
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
(see the paragraph which begins with "*NOTE* on CD and WP polarity."
in 'Documentation/devicetree/bindings/mmc/mmc.txt'.)
--
Rask Ingemann Lambertsen
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 2/7] clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
2017-02-26 1:19 ` Icenowy Zheng
(?)
(?)
@ 2017-02-26 9:52 ` Rask Ingemann Lambertsen
-1 siblings, 0 replies; 62+ messages in thread
From: Rask Ingemann Lambertsen @ 2017-02-26 9:52 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara, devicetree, linux-kernel,
linux-sunxi, linux-clk, linux-arm-kernel
On Sun, Feb 26, 2017 at 09:19:51AM +0800, Icenowy Zheng wrote:
> As the CCU in the Allwinner H5 SoC is very similar to the one in H3,
> rename the H3 driver to sunxi-h3-h5 so that it can be extended with H5
> support.
>
> Trasitional header symlinks are created, to ensure current device tree
s/Trasitional/Transitional/ I guess.
> files which included sun8i-h3-ccu.h can compile.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> Changes in v5:
> - Add the reason to create trasitional headers in commit message.
Likewise.
--
Rask Ingemann Lambertsen
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 2/7] clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
@ 2017-02-26 9:52 ` Rask Ingemann Lambertsen
0 siblings, 0 replies; 62+ messages in thread
From: Rask Ingemann Lambertsen @ 2017-02-26 9:52 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, Catalin Marinas, linux-sunxi, Will Deacon,
linux-kernel, Chen-Yu Tsai, Rob Herring, Andre Przywara,
Maxime Ripard, linux-clk, linux-arm-kernel
On Sun, Feb 26, 2017 at 09:19:51AM +0800, Icenowy Zheng wrote:
> As the CCU in the Allwinner H5 SoC is very similar to the one in H3,
> rename the H3 driver to sunxi-h3-h5 so that it can be extended with H5
> support.
>
> Trasitional header symlinks are created, to ensure current device tree
s/Trasitional/Transitional/ I guess.
> files which included sun8i-h3-ccu.h can compile.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> Changes in v5:
> - Add the reason to create trasitional headers in commit message.
Likewise.
--
Rask Ingemann Lambertsen
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 2/7] clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
@ 2017-02-26 9:52 ` Rask Ingemann Lambertsen
0 siblings, 0 replies; 62+ messages in thread
From: Rask Ingemann Lambertsen @ 2017-02-26 9:52 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, Catalin Marinas, linux-sunxi, Will Deacon,
linux-kernel, Chen-Yu Tsai, Rob Herring, Andre Przywara,
Maxime Ripard, linux-clk, linux-arm-kernel
On Sun, Feb 26, 2017 at 09:19:51AM +0800, Icenowy Zheng wrote:
> As the CCU in the Allwinner H5 SoC is very similar to the one in H3,
> rename the H3 driver to sunxi-h3-h5 so that it can be extended with H5
> support.
>
> Trasitional header symlinks are created, to ensure current device tree
s/Trasitional/Transitional/ I guess.
> files which included sun8i-h3-ccu.h can compile.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> Changes in v5:
> - Add the reason to create trasitional headers in commit message.
Likewise.
--
Rask Ingemann Lambertsen
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 62+ messages in thread
* [PATCH v5 2/7] clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
@ 2017-02-26 9:52 ` Rask Ingemann Lambertsen
0 siblings, 0 replies; 62+ messages in thread
From: Rask Ingemann Lambertsen @ 2017-02-26 9:52 UTC (permalink / raw)
To: linux-arm-kernel
On Sun, Feb 26, 2017 at 09:19:51AM +0800, Icenowy Zheng wrote:
> As the CCU in the Allwinner H5 SoC is very similar to the one in H3,
> rename the H3 driver to sunxi-h3-h5 so that it can be extended with H5
> support.
>
> Trasitional header symlinks are created, to ensure current device tree
s/Trasitional/Transitional/ I guess.
> files which included sun8i-h3-ccu.h can compile.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> Changes in v5:
> - Add the reason to create trasitional headers in commit message.
Likewise.
--
Rask Ingemann Lambertsen
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 6/7] arm64: dts: allwinner: add Allwinner H5 .dtsi
2017-02-26 8:55 ` Rask Ingemann Lambertsen
(?)
@ 2017-02-26 14:54 ` Icenowy Zheng
-1 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 14:54 UTC (permalink / raw)
To: Rask Ingemann Lambertsen
Cc: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
26.02.2017, 16:56, "Rask Ingemann Lambertsen" <rask-SivP7zSAdNDZaaYASwVUlg@public.gmane.org>:
> On Sun, Feb 26, 2017 at 09:19:55AM +0800, Icenowy Zheng wrote:
>> From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
>>
>> The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
>> Cortex-A53 cores instead.
>> Based on the now shared base .dtsi describing the common peripherals
>> describe the H5 specific nodes on top of that.
>> That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
>>
>> Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
>> [Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
>> refactor, commit message change to met new arm64 naming scheme,
>
> s/change to met/change to meet/ or s/change to met/changed to meet/ ?
>
>> diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
>> new file mode 120000
>> index 000000000000..036f01dc2b9b
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
>> @@ -0,0 +1 @@
>> +../../../../arm/boot/dts/sunxi-h3-h5.dtsi
>> \ No newline at end of file
>
> But it's missing more than just a newline, isn't it? Shouldn't it read
>
> #include <../../../../arm/boot/dts/sunxi-h3-h5.dtsi>
Oh you may do not know what a symlink seems like in git format-patch.
This is a symlink.
It's mode is not 100644, but 120000
>
> ?
>
> --
> Rask Ingemann Lambertsen
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 6/7] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-02-26 14:54 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 14:54 UTC (permalink / raw)
To: Rask Ingemann Lambertsen
Cc: devicetree, Catalin Marinas, linux-sunxi, Will Deacon,
linux-kernel, Chen-Yu Tsai, Rob Herring, Andre Przywara,
Maxime Ripard, linux-clk, linux-arm-kernel
CgoyNi4wMi4yMDE3LCAxNjo1NiwgIlJhc2sgSW5nZW1hbm4gTGFtYmVydHNlbiIgPHJhc2tAZm9y
bWVsZGVyLmRrPjoKPiBPbiBTdW4sIEZlYiAyNiwgMjAxNyBhdCAwOToxOTo1NUFNICswODAwLCBJ
Y2Vub3d5IFpoZW5nIHdyb3RlOgo+PiDCoEZyb206IEFuZHJlIFByenl3YXJhIDxhbmRyZS5wcnp5
d2FyYUBhcm0uY29tPgo+Pgo+PiDCoFRoZSBBbGx3aW5uZXIgSDUgU29DIGlzIHBpbi1jb21wYXRp
YmxlIHRvIHRoZSBIMyBTb0MsIGJ1dCB1c2VzCj4+IMKgQ29ydGV4LUE1MyBjb3JlcyBpbnN0ZWFk
Lgo+PiDCoEJhc2VkIG9uIHRoZSBub3cgc2hhcmVkIGJhc2UgLmR0c2kgZGVzY3JpYmluZyB0aGUg
Y29tbW9uIHBlcmlwaGVyYWxzCj4+IMKgZGVzY3JpYmUgdGhlIEg1IHNwZWNpZmljIG5vZGVzIG9u
IHRvcCBvZiB0aGF0Lgo+PiDCoFRoYXQgc3ltbGlua3MgaW4gdGhlIHN1bnhpLWgzLWg1LmR0c2kg
ZnJvbSB0aGUgYXJjaC9hcm0gdHJlZS4KPj4KPj4gwqBTaWduZWQtb2ZmLWJ5OiBBbmRyZSBQcnp5
d2FyYSA8YW5kcmUucHJ6eXdhcmFAYXJtLmNvbT4KPj4gwqBbSWNlbm93eTogYWRkIEg1IHBpbmN0
cmwgY29tcGF0aWJsZSwgYW5kIGNoYW5nZXMgZm9yIG15IGgzLWg1IGR0c2kKPj4gwqDCoHJlZmFj
dG9yLCBjb21taXQgbWVzc2FnZSBjaGFuZ2UgdG8gbWV0IG5ldyBhcm02NCBuYW1pbmcgc2NoZW1l
LAo+Cj4gcy9jaGFuZ2UgdG8gbWV0L2NoYW5nZSB0byBtZWV0LyBvciBzL2NoYW5nZSB0byBtZXQv
Y2hhbmdlZCB0byBtZWV0LyA/Cj4KPj4gwqBkaWZmIC0tZ2l0IGEvYXJjaC9hcm02NC9ib290L2R0
cy9hbGx3aW5uZXIvc3VueGktaDMtaDUuZHRzaSBiL2FyY2gvYXJtNjQvYm9vdC9kdHMvYWxsd2lu
bmVyL3N1bnhpLWgzLWg1LmR0c2kKPj4gwqBuZXcgZmlsZSBtb2RlIDEyMDAwMAo+PiDCoGluZGV4
IDAwMDAwMDAwMDAwMC4uMDM2ZjAxZGMyYjliCj4+IMKgLS0tIC9kZXYvbnVsbAo+PiDCoCsrKyBi
L2FyY2gvYXJtNjQvYm9vdC9kdHMvYWxsd2lubmVyL3N1bnhpLWgzLWg1LmR0c2kKPj4gwqBAQCAt
MCwwICsxIEBACj4+IMKgKy4uLy4uLy4uLy4uL2FybS9ib290L2R0cy9zdW54aS1oMy1oNS5kdHNp
Cj4+IMKgXCBObyBuZXdsaW5lIGF0IGVuZCBvZiBmaWxlCj4KPiBCdXQgaXQncyBtaXNzaW5nIG1v
cmUgdGhhbiBqdXN0IGEgbmV3bGluZSwgaXNuJ3QgaXQ/IFNob3VsZG4ndCBpdCByZWFkCj4KPiAj
aW5jbHVkZSA8Li4vLi4vLi4vLi4vYXJtL2Jvb3QvZHRzL3N1bnhpLWgzLWg1LmR0c2k+CgpPaCB5
b3UgbWF5IGRvIG5vdCBrbm93IHdoYXQgYSBzeW1saW5rIHNlZW1zIGxpa2UgaW4gZ2l0IGZvcm1h
dC1wYXRjaC4KClRoaXMgaXMgYSBzeW1saW5rLgoKSXQncyBtb2RlIGlzIG5vdCAxMDA2NDQsIGJ1
dCAxMjAwMDAKCj4KPiA/Cj4KPiAtLQo+IFJhc2sgSW5nZW1hbm4gTGFtYmVydHNlbgoKX19fX19f
X19fX19fX19fX19fX19fX19fX19fX19fX19fX19fX19fX19fX19fX18KbGludXgtYXJtLWtlcm5l
bCBtYWlsaW5nIGxpc3QKbGludXgtYXJtLWtlcm5lbEBsaXN0cy5pbmZyYWRlYWQub3JnCmh0dHA6
Ly9saXN0cy5pbmZyYWRlYWQub3JnL21haWxtYW4vbGlzdGluZm8vbGludXgtYXJtLWtlcm5lbAo=
^ permalink raw reply [flat|nested] 62+ messages in thread
* [PATCH v5 6/7] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-02-26 14:54 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 14:54 UTC (permalink / raw)
To: linux-arm-kernel
26.02.2017, 16:56, "Rask Ingemann Lambertsen" <rask@formelder.dk>:
> On Sun, Feb 26, 2017 at 09:19:55AM +0800, Icenowy Zheng wrote:
>> ?From: Andre Przywara <andre.przywara@arm.com>
>>
>> ?The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
>> ?Cortex-A53 cores instead.
>> ?Based on the now shared base .dtsi describing the common peripherals
>> ?describe the H5 specific nodes on top of that.
>> ?That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
>>
>> ?Signed-off-by: Andre Przywara <andre.przywara@arm.com>
>> ?[Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
>> ??refactor, commit message change to met new arm64 naming scheme,
>
> s/change to met/change to meet/ or s/change to met/changed to meet/ ?
>
>> ?diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
>> ?new file mode 120000
>> ?index 000000000000..036f01dc2b9b
>> ?--- /dev/null
>> ?+++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
>> ?@@ -0,0 +1 @@
>> ?+../../../../arm/boot/dts/sunxi-h3-h5.dtsi
>> ?\ No newline at end of file
>
> But it's missing more than just a newline, isn't it? Shouldn't it read
>
> #include <../../../../arm/boot/dts/sunxi-h3-h5.dtsi>
Oh you may do not know what a symlink seems like in git format-patch.
This is a symlink.
It's mode is not 100644, but 120000
>
> ?
>
> --
> Rask Ingemann Lambertsen
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 2/7] clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
2017-02-26 9:52 ` Rask Ingemann Lambertsen
(?)
@ 2017-02-26 14:57 ` Icenowy Zheng
-1 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 14:57 UTC (permalink / raw)
To: Rask Ingemann Lambertsen
Cc: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Catalin Marinas,
Will Deacon, Andre Przywara, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
26.02.2017, 17:52, "Rask Ingemann Lambertsen" <rask-SivP7zSAdNDZaaYASwVUlg@public.gmane.org>:
> On Sun, Feb 26, 2017 at 09:19:51AM +0800, Icenowy Zheng wrote:
>> As the CCU in the Allwinner H5 SoC is very similar to the one in H3,
>> rename the H3 driver to sunxi-h3-h5 so that it can be extended with H5
>> support.
>>
>> Trasitional header symlinks are created, to ensure current device tree
>
> s/Trasitional/Transitional/ I guess.
>
>> files which included sun8i-h3-ccu.h can compile.
>>
>> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
>> ---
>> Changes in v5:
>> - Add the reason to create trasitional headers in commit message.
>
> Likewise.
Thanks ;-)
>
> --
> Rask Ingemann Lambertsen
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 2/7] clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
@ 2017-02-26 14:57 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 14:57 UTC (permalink / raw)
To: Rask Ingemann Lambertsen
Cc: devicetree, Catalin Marinas, linux-sunxi, Will Deacon,
linux-kernel, Chen-Yu Tsai, Rob Herring, Andre Przywara,
Maxime Ripard, linux-clk, linux-arm-kernel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^ permalink raw reply [flat|nested] 62+ messages in thread
* [PATCH v5 2/7] clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
@ 2017-02-26 14:57 ` Icenowy Zheng
0 siblings, 0 replies; 62+ messages in thread
From: Icenowy Zheng @ 2017-02-26 14:57 UTC (permalink / raw)
To: linux-arm-kernel
26.02.2017, 17:52, "Rask Ingemann Lambertsen" <rask@formelder.dk>:
> On Sun, Feb 26, 2017 at 09:19:51AM +0800, Icenowy Zheng wrote:
>> ?As the CCU in the Allwinner H5 SoC is very similar to the one in H3,
>> ?rename the H3 driver to sunxi-h3-h5 so that it can be extended with H5
>> ?support.
>>
>> ?Trasitional header symlinks are created, to ensure current device tree
>
> s/Trasitional/Transitional/ I guess.
>
>> ?files which included sun8i-h3-ccu.h can compile.
>>
>> ?Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
>> ?---
>> ?Changes in v5:
>> ?- Add the reason to create trasitional headers in commit message.
>
> Likewise.
Thanks ;-)
>
> --
> Rask Ingemann Lambertsen
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 5/7] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-02-27 8:20 ` Marc Zyngier
0 siblings, 0 replies; 62+ messages in thread
From: Marc Zyngier @ 2017-02-27 8:20 UTC (permalink / raw)
To: Chen-Yu Tsai, Icenowy Zheng
Cc: Rob Herring, Maxime Ripard, Catalin Marinas, Will Deacon,
Andre Przywara, linux-clk, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
On 26/02/17 03:46, Chen-Yu Tsai wrote:
> Hi,
[...]
>> - gic: interrupt-controller@01c81000 {
>> - compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
>> - reg = <0x01c81000 0x1000>,
>> - <0x01c82000 0x2000>,
>> - <0x01c84000 0x2000>,
>> - <0x01c86000 0x2000>;
>> - interrupt-controller;
>> - #interrupt-cells = <3>;
>> - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
>
> The gic bits seem to be the same for both SoCs, aside from the
> different compatible
> string. Marc had sent a series to change them all to arm,gic-400, which is the
> proper name for it, but it wasn't merged. I'm assuming the compatibles
> are equal?
> If so then it can also be shared.
The series was fixing the various GICv2 memory maps, and is now in
mainline. If you have a good indication that all these SoCs are indeed
featuring a gic-400, feel free to amend the DT.
Thanks,
M.
--
Jazz is not dead. It just smells funny...
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 5/7] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-02-27 8:20 ` Marc Zyngier
0 siblings, 0 replies; 62+ messages in thread
From: Marc Zyngier @ 2017-02-27 8:20 UTC (permalink / raw)
To: Chen-Yu Tsai, Icenowy Zheng
Cc: Rob Herring, Maxime Ripard, Catalin Marinas, Will Deacon,
Andre Przywara, linux-clk, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
On 26/02/17 03:46, Chen-Yu Tsai wrote:
> Hi,
[...]
>> - gic: interrupt-controller@01c81000 {
>> - compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
>> - reg = <0x01c81000 0x1000>,
>> - <0x01c82000 0x2000>,
>> - <0x01c84000 0x2000>,
>> - <0x01c86000 0x2000>;
>> - interrupt-controller;
>> - #interrupt-cells = <3>;
>> - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
>
> The gic bits seem to be the same for both SoCs, aside from the
> different compatible
> string. Marc had sent a series to change them all to arm,gic-400, which is the
> proper name for it, but it wasn't merged. I'm assuming the compatibles
> are equal?
> If so then it can also be shared.
The series was fixing the various GICv2 memory maps, and is now in
mainline. If you have a good indication that all these SoCs are indeed
featuring a gic-400, feel free to amend the DT.
Thanks,
M.
--
Jazz is not dead. It just smells funny...
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 5/7] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-02-27 8:20 ` Marc Zyngier
0 siblings, 0 replies; 62+ messages in thread
From: Marc Zyngier @ 2017-02-27 8:20 UTC (permalink / raw)
To: Chen-Yu Tsai, Icenowy Zheng
Cc: devicetree, Catalin Marinas, Will Deacon, linux-kernel,
linux-sunxi, Rob Herring, Andre Przywara, Maxime Ripard,
linux-clk, linux-arm-kernel
On 26/02/17 03:46, Chen-Yu Tsai wrote:
> Hi,
[...]
>> - gic: interrupt-controller@01c81000 {
>> - compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
>> - reg = <0x01c81000 0x1000>,
>> - <0x01c82000 0x2000>,
>> - <0x01c84000 0x2000>,
>> - <0x01c86000 0x2000>;
>> - interrupt-controller;
>> - #interrupt-cells = <3>;
>> - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
>
> The gic bits seem to be the same for both SoCs, aside from the
> different compatible
> string. Marc had sent a series to change them all to arm,gic-400, which is the
> proper name for it, but it wasn't merged. I'm assuming the compatibles
> are equal?
> If so then it can also be shared.
The series was fixing the various GICv2 memory maps, and is now in
mainline. If you have a good indication that all these SoCs are indeed
featuring a gic-400, feel free to amend the DT.
Thanks,
M.
--
Jazz is not dead. It just smells funny...
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 62+ messages in thread
* [PATCH v5 5/7] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-02-27 8:20 ` Marc Zyngier
0 siblings, 0 replies; 62+ messages in thread
From: Marc Zyngier @ 2017-02-27 8:20 UTC (permalink / raw)
To: linux-arm-kernel
On 26/02/17 03:46, Chen-Yu Tsai wrote:
> Hi,
[...]
>> - gic: interrupt-controller at 01c81000 {
>> - compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
>> - reg = <0x01c81000 0x1000>,
>> - <0x01c82000 0x2000>,
>> - <0x01c84000 0x2000>,
>> - <0x01c86000 0x2000>;
>> - interrupt-controller;
>> - #interrupt-cells = <3>;
>> - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
>
> The gic bits seem to be the same for both SoCs, aside from the
> different compatible
> string. Marc had sent a series to change them all to arm,gic-400, which is the
> proper name for it, but it wasn't merged. I'm assuming the compatibles
> are equal?
> If so then it can also be shared.
The series was fixing the various GICv2 memory maps, and is now in
mainline. If you have a good indication that all these SoCs are indeed
featuring a gic-400, feel free to amend the DT.
Thanks,
M.
--
Jazz is not dead. It just smells funny...
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 1/7] arm64: allwinner: Kconfig: add essential pinctrl driver for H5
@ 2017-02-27 8:25 ` Maxime Ripard
0 siblings, 0 replies; 62+ messages in thread
From: Maxime Ripard @ 2017-02-27 8:25 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Rob Herring, Chen-Yu Tsai, Catalin Marinas, Will Deacon,
Andre Przywara, linux-clk, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 1477 bytes --]
On Sun, Feb 26, 2017 at 09:19:50AM +0800, Icenowy Zheng wrote:
> H5 SoC has two pin controllers, one (in user manual called "CPUx") needs
> a slightly advanced driver, and the other (called "CPUs") is just equal
> to the on in H3, and the H3 driver can be just reused.
>
> Select the two necessary pinctrl drivers when building kernel for
> Allwinner SoCs.
>
> Also add H5 in the option's description.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> arch/arm64/Kconfig.platforms | 5 ++++-
> 1 file changed, 4 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
> index 129cc5ae4091..81f0d6149c2e 100644
> --- a/arch/arm64/Kconfig.platforms
> +++ b/arch/arm64/Kconfig.platforms
> @@ -5,8 +5,11 @@ config ARCH_SUNXI
> select GENERIC_IRQ_CHIP
> select PINCTRL
> select PINCTRL_SUN50I_A64
> + select PINCTRL_SUN50I_H5
> + select PINCTRL_SUN8I_H3_R
Why not add those options as def_bool instead?
Being able to remove them certainly have values if you want to strip
them down.
> help
> - This enables support for Allwinner sunxi based SoCs like the A64.
> + This enables support for Allwinner sunxi based SoCs like the A64
> + and H5.
There's no point in having an ever growing list of SoCs here. You can
just remove the mention of the A64.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 1/7] arm64: allwinner: Kconfig: add essential pinctrl driver for H5
@ 2017-02-27 8:25 ` Maxime Ripard
0 siblings, 0 replies; 62+ messages in thread
From: Maxime Ripard @ 2017-02-27 8:25 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Rob Herring, Chen-Yu Tsai, Catalin Marinas, Will Deacon,
Andre Przywara, linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 1451 bytes --]
On Sun, Feb 26, 2017 at 09:19:50AM +0800, Icenowy Zheng wrote:
> H5 SoC has two pin controllers, one (in user manual called "CPUx") needs
> a slightly advanced driver, and the other (called "CPUs") is just equal
> to the on in H3, and the H3 driver can be just reused.
>
> Select the two necessary pinctrl drivers when building kernel for
> Allwinner SoCs.
>
> Also add H5 in the option's description.
>
> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
> ---
> arch/arm64/Kconfig.platforms | 5 ++++-
> 1 file changed, 4 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
> index 129cc5ae4091..81f0d6149c2e 100644
> --- a/arch/arm64/Kconfig.platforms
> +++ b/arch/arm64/Kconfig.platforms
> @@ -5,8 +5,11 @@ config ARCH_SUNXI
> select GENERIC_IRQ_CHIP
> select PINCTRL
> select PINCTRL_SUN50I_A64
> + select PINCTRL_SUN50I_H5
> + select PINCTRL_SUN8I_H3_R
Why not add those options as def_bool instead?
Being able to remove them certainly have values if you want to strip
them down.
> help
> - This enables support for Allwinner sunxi based SoCs like the A64.
> + This enables support for Allwinner sunxi based SoCs like the A64
> + and H5.
There's no point in having an ever growing list of SoCs here. You can
just remove the mention of the A64.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 1/7] arm64: allwinner: Kconfig: add essential pinctrl driver for H5
@ 2017-02-27 8:25 ` Maxime Ripard
0 siblings, 0 replies; 62+ messages in thread
From: Maxime Ripard @ 2017-02-27 8:25 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, Catalin Marinas, linux-sunxi, Will Deacon,
linux-kernel, Chen-Yu Tsai, Rob Herring, Andre Przywara,
linux-clk, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 1477 bytes --]
On Sun, Feb 26, 2017 at 09:19:50AM +0800, Icenowy Zheng wrote:
> H5 SoC has two pin controllers, one (in user manual called "CPUx") needs
> a slightly advanced driver, and the other (called "CPUs") is just equal
> to the on in H3, and the H3 driver can be just reused.
>
> Select the two necessary pinctrl drivers when building kernel for
> Allwinner SoCs.
>
> Also add H5 in the option's description.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> arch/arm64/Kconfig.platforms | 5 ++++-
> 1 file changed, 4 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
> index 129cc5ae4091..81f0d6149c2e 100644
> --- a/arch/arm64/Kconfig.platforms
> +++ b/arch/arm64/Kconfig.platforms
> @@ -5,8 +5,11 @@ config ARCH_SUNXI
> select GENERIC_IRQ_CHIP
> select PINCTRL
> select PINCTRL_SUN50I_A64
> + select PINCTRL_SUN50I_H5
> + select PINCTRL_SUN8I_H3_R
Why not add those options as def_bool instead?
Being able to remove them certainly have values if you want to strip
them down.
> help
> - This enables support for Allwinner sunxi based SoCs like the A64.
> + This enables support for Allwinner sunxi based SoCs like the A64
> + and H5.
There's no point in having an ever growing list of SoCs here. You can
just remove the mention of the A64.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 62+ messages in thread
* [PATCH v5 1/7] arm64: allwinner: Kconfig: add essential pinctrl driver for H5
@ 2017-02-27 8:25 ` Maxime Ripard
0 siblings, 0 replies; 62+ messages in thread
From: Maxime Ripard @ 2017-02-27 8:25 UTC (permalink / raw)
To: linux-arm-kernel
On Sun, Feb 26, 2017 at 09:19:50AM +0800, Icenowy Zheng wrote:
> H5 SoC has two pin controllers, one (in user manual called "CPUx") needs
> a slightly advanced driver, and the other (called "CPUs") is just equal
> to the on in H3, and the H3 driver can be just reused.
>
> Select the two necessary pinctrl drivers when building kernel for
> Allwinner SoCs.
>
> Also add H5 in the option's description.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> arch/arm64/Kconfig.platforms | 5 ++++-
> 1 file changed, 4 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
> index 129cc5ae4091..81f0d6149c2e 100644
> --- a/arch/arm64/Kconfig.platforms
> +++ b/arch/arm64/Kconfig.platforms
> @@ -5,8 +5,11 @@ config ARCH_SUNXI
> select GENERIC_IRQ_CHIP
> select PINCTRL
> select PINCTRL_SUN50I_A64
> + select PINCTRL_SUN50I_H5
> + select PINCTRL_SUN8I_H3_R
Why not add those options as def_bool instead?
Being able to remove them certainly have values if you want to strip
them down.
> help
> - This enables support for Allwinner sunxi based SoCs like the A64.
> + This enables support for Allwinner sunxi based SoCs like the A64
> + and H5.
There's no point in having an ever growing list of SoCs here. You can
just remove the mention of the A64.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170227/eb496976/attachment.sig>
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 2/7] clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
@ 2017-02-27 12:24 ` Maxime Ripard
0 siblings, 0 replies; 62+ messages in thread
From: Maxime Ripard @ 2017-02-27 12:24 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Rob Herring, Chen-Yu Tsai, Catalin Marinas, Will Deacon,
Andre Przywara, linux-clk, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 739 bytes --]
Hi,
On Sun, Feb 26, 2017 at 09:19:51AM +0800, Icenowy Zheng wrote:
> As the CCU in the Allwinner H5 SoC is very similar to the one in H3,
> rename the H3 driver to sunxi-h3-h5 so that it can be extended with H5
> support.
>
> Trasitional header symlinks are created, to ensure current device tree
> files which included sun8i-h3-ccu.h can compile.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Just like for the R40, I wonder whether this is needed at all. We have
a lot of other drivers that we don't have to rename to support new
SoCs. This is kind of weird to make an exception for this one only.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 2/7] clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
@ 2017-02-27 12:24 ` Maxime Ripard
0 siblings, 0 replies; 62+ messages in thread
From: Maxime Ripard @ 2017-02-27 12:24 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Rob Herring, Chen-Yu Tsai, Catalin Marinas, Will Deacon,
Andre Przywara, linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 736 bytes --]
Hi,
On Sun, Feb 26, 2017 at 09:19:51AM +0800, Icenowy Zheng wrote:
> As the CCU in the Allwinner H5 SoC is very similar to the one in H3,
> rename the H3 driver to sunxi-h3-h5 so that it can be extended with H5
> support.
>
> Trasitional header symlinks are created, to ensure current device tree
> files which included sun8i-h3-ccu.h can compile.
>
> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
Just like for the R40, I wonder whether this is needed at all. We have
a lot of other drivers that we don't have to rename to support new
SoCs. This is kind of weird to make an exception for this one only.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 62+ messages in thread
* Re: [PATCH v5 2/7] clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
@ 2017-02-27 12:24 ` Maxime Ripard
0 siblings, 0 replies; 62+ messages in thread
From: Maxime Ripard @ 2017-02-27 12:24 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, Catalin Marinas, linux-sunxi, Will Deacon,
linux-kernel, Chen-Yu Tsai, Rob Herring, Andre Przywara,
linux-clk, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 739 bytes --]
Hi,
On Sun, Feb 26, 2017 at 09:19:51AM +0800, Icenowy Zheng wrote:
> As the CCU in the Allwinner H5 SoC is very similar to the one in H3,
> rename the H3 driver to sunxi-h3-h5 so that it can be extended with H5
> support.
>
> Trasitional header symlinks are created, to ensure current device tree
> files which included sun8i-h3-ccu.h can compile.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Just like for the R40, I wonder whether this is needed at all. We have
a lot of other drivers that we don't have to rename to support new
SoCs. This is kind of weird to make an exception for this one only.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 62+ messages in thread
* [PATCH v5 2/7] clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5
@ 2017-02-27 12:24 ` Maxime Ripard
0 siblings, 0 replies; 62+ messages in thread
From: Maxime Ripard @ 2017-02-27 12:24 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On Sun, Feb 26, 2017 at 09:19:51AM +0800, Icenowy Zheng wrote:
> As the CCU in the Allwinner H5 SoC is very similar to the one in H3,
> rename the H3 driver to sunxi-h3-h5 so that it can be extended with H5
> support.
>
> Trasitional header symlinks are created, to ensure current device tree
> files which included sun8i-h3-ccu.h can compile.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Just like for the R40, I wonder whether this is needed at all. We have
a lot of other drivers that we don't have to rename to support new
SoCs. This is kind of weird to make an exception for this one only.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170227/d4422d54/attachment.sig>
^ permalink raw reply [flat|nested] 62+ messages in thread
end of thread, other threads:[~2017-02-27 12:31 UTC | newest]
Thread overview: 62+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-02-26 1:19 [PATCH v5 0/7] Allwinner H5 and Orange Pi PC2 support Icenowy Zheng
2017-02-26 1:19 ` Icenowy Zheng
2017-02-26 1:19 ` Icenowy Zheng
[not found] ` <20170226011956.53581-1-icenowy-ymACFijhrKM@public.gmane.org>
2017-02-26 1:19 ` [PATCH v5 1/7] arm64: allwinner: Kconfig: add essential pinctrl driver for H5 Icenowy Zheng
2017-02-26 1:19 ` Icenowy Zheng
2017-02-26 1:19 ` Icenowy Zheng
2017-02-27 8:25 ` Maxime Ripard
2017-02-27 8:25 ` Maxime Ripard
2017-02-27 8:25 ` Maxime Ripard
2017-02-27 8:25 ` Maxime Ripard
2017-02-26 1:19 ` [PATCH v5 2/7] clk: sunxi-ng: rename sun8i-h3 driver to sunxi-h3-h5 Icenowy Zheng
2017-02-26 1:19 ` Icenowy Zheng
2017-02-26 1:19 ` Icenowy Zheng
2017-02-26 9:52 ` Rask Ingemann Lambertsen
2017-02-26 9:52 ` Rask Ingemann Lambertsen
2017-02-26 9:52 ` Rask Ingemann Lambertsen
2017-02-26 9:52 ` Rask Ingemann Lambertsen
2017-02-26 14:57 ` Icenowy Zheng
2017-02-26 14:57 ` Icenowy Zheng
2017-02-26 14:57 ` Icenowy Zheng
2017-02-27 12:24 ` Maxime Ripard
2017-02-27 12:24 ` Maxime Ripard
2017-02-27 12:24 ` Maxime Ripard
2017-02-27 12:24 ` Maxime Ripard
2017-02-26 1:19 ` [PATCH v5 3/7] clk: sunxi-ng: add support for Allwinner H5 SoC Icenowy Zheng
2017-02-26 1:19 ` Icenowy Zheng
2017-02-26 1:19 ` Icenowy Zheng
2017-02-26 1:19 ` [PATCH v5 4/7] ARM: dts: sun8i: convert H3 dtsi to use new sunxi-h3-h5 binding header Icenowy Zheng
2017-02-26 1:19 ` Icenowy Zheng
2017-02-26 1:19 ` Icenowy Zheng
2017-02-26 1:19 ` [PATCH v5 5/7] arm: dts: sun8i: split Allwinner H3 .dtsi Icenowy Zheng
2017-02-26 1:19 ` Icenowy Zheng
2017-02-26 1:19 ` Icenowy Zheng
2017-02-26 3:46 ` Chen-Yu Tsai
2017-02-26 3:46 ` Chen-Yu Tsai
2017-02-26 3:46 ` Chen-Yu Tsai
2017-02-26 3:46 ` Chen-Yu Tsai
2017-02-27 8:20 ` Marc Zyngier
2017-02-27 8:20 ` Marc Zyngier
2017-02-27 8:20 ` Marc Zyngier
2017-02-27 8:20 ` Marc Zyngier
2017-02-26 1:19 ` [PATCH v5 6/7] arm64: dts: allwinner: add Allwinner H5 .dtsi Icenowy Zheng
2017-02-26 1:19 ` Icenowy Zheng
2017-02-26 1:19 ` Icenowy Zheng
2017-02-26 8:55 ` Rask Ingemann Lambertsen
2017-02-26 8:55 ` Rask Ingemann Lambertsen
2017-02-26 8:55 ` Rask Ingemann Lambertsen
2017-02-26 8:55 ` Rask Ingemann Lambertsen
2017-02-26 9:00 ` Chen-Yu Tsai
2017-02-26 9:00 ` Chen-Yu Tsai
2017-02-26 9:00 ` Chen-Yu Tsai
2017-02-26 9:00 ` Chen-Yu Tsai
2017-02-26 14:54 ` Icenowy Zheng
2017-02-26 14:54 ` Icenowy Zheng
2017-02-26 14:54 ` Icenowy Zheng
2017-02-26 1:19 ` [PATCH v5 7/7] arm64: dts: sunxi: add support for the Orange Pi PC 2 board Icenowy Zheng
2017-02-26 1:19 ` Icenowy Zheng
2017-02-26 1:19 ` Icenowy Zheng
2017-02-26 9:19 ` Rask Ingemann Lambertsen
2017-02-26 9:19 ` Rask Ingemann Lambertsen
2017-02-26 9:19 ` Rask Ingemann Lambertsen
2017-02-26 9:19 ` Rask Ingemann Lambertsen
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.