[PATCH 0/9] arm64: dts: qcom: sm8150-hdk: enable display output

[PATCH 0/9] arm64: dts: qcom: sm8150-hdk: enable display output

[Dmitry Baryshkov]

Enable display output on the SM8150 HDK device. This includes HDMI
output through the onboard DSI-HDMI bridge and DP output on the USB-C
port.

Dmitry Baryshkov (9):
  dt-bindings: display: msm: dp: declare compatible string for sm8150
  arm64: dts: qcom: sm8150: use SoC-specific compat for RPMh stats
  arm64: dts: qcom: sm8150: make dispcc cast minimal vote on MMCX
  arm64: dts: qcom: sm8150-hdk: enable HDMI output
  arm64: dts: qcom: sm8150-hdk: fix SS USB regulators
  arm64: dts: qcom: sm8150: add DisplayPort controller
  arm64: dts: qcom: sm8150: add USB-C ports to the USB+DP QMP PHY
  arm64: dts: qcom: sm8150: add USB-C ports to the OTG USB host
  arm64: dts: qcom: sm8150-hdk: enable DisplayPort and USB-C altmode

 .../bindings/display/msm/dp-controller.yaml   |   1 +
 arch/arm64/boot/dts/qcom/sm8150-hdk.dts       | 264 +++++++++++++++++-
 arch/arm64/boot/dts/qcom/sm8150.dtsi          | 132 ++++++++-
 3 files changed, 386 insertions(+), 11 deletions(-)

-- 
2.39.2

[PATCH 0/9] arm64: dts: qcom: sm8150-hdk: enable display output

[Dmitry Baryshkov]

Enable display output on the SM8150 HDK device. This includes HDMI
output through the onboard DSI-HDMI bridge and DP output on the USB-C
port.

Dmitry Baryshkov (9):
  dt-bindings: display: msm: dp: declare compatible string for sm8150
  arm64: dts: qcom: sm8150: use SoC-specific compat for RPMh stats
  arm64: dts: qcom: sm8150: make dispcc cast minimal vote on MMCX
  arm64: dts: qcom: sm8150-hdk: enable HDMI output
  arm64: dts: qcom: sm8150-hdk: fix SS USB regulators
  arm64: dts: qcom: sm8150: add DisplayPort controller
  arm64: dts: qcom: sm8150: add USB-C ports to the USB+DP QMP PHY
  arm64: dts: qcom: sm8150: add USB-C ports to the OTG USB host
  arm64: dts: qcom: sm8150-hdk: enable DisplayPort and USB-C altmode

 .../bindings/display/msm/dp-controller.yaml   |   1 +
 arch/arm64/boot/dts/qcom/sm8150-hdk.dts       | 264 +++++++++++++++++-
 arch/arm64/boot/dts/qcom/sm8150.dtsi          | 132 ++++++++-
 3 files changed, 386 insertions(+), 11 deletions(-)

-- 
2.39.2

[PATCH 1/9] dt-bindings: display: msm: dp: declare compatible string for sm8150

[Dmitry Baryshkov]

Add compatible string for the DisplayPort controller found on the
Qualcomm SM8150 platform.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 Documentation/devicetree/bindings/display/msm/dp-controller.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/display/msm/dp-controller.yaml b/Documentation/devicetree/bindings/display/msm/dp-controller.yaml
index dbe398f84ffb..f850bd9b8263 100644
--- a/Documentation/devicetree/bindings/display/msm/dp-controller.yaml
+++ b/Documentation/devicetree/bindings/display/msm/dp-controller.yaml
@@ -28,6 +28,7 @@ properties:
           - qcom,sm8350-dp
       - items:
           - enum:
+              - qcom,sm8150-dp
               - qcom,sm8250-dp
               - qcom,sm8450-dp
               - qcom,sm8550-dp
-- 
2.39.2

[PATCH 1/9] dt-bindings: display: msm: dp: declare compatible string for sm8150

[Dmitry Baryshkov]

Add compatible string for the DisplayPort controller found on the
Qualcomm SM8150 platform.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 Documentation/devicetree/bindings/display/msm/dp-controller.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/display/msm/dp-controller.yaml b/Documentation/devicetree/bindings/display/msm/dp-controller.yaml
index dbe398f84ffb..f850bd9b8263 100644
--- a/Documentation/devicetree/bindings/display/msm/dp-controller.yaml
+++ b/Documentation/devicetree/bindings/display/msm/dp-controller.yaml
@@ -28,6 +28,7 @@ properties:
           - qcom,sm8350-dp
       - items:
           - enum:
+              - qcom,sm8150-dp
               - qcom,sm8250-dp
               - qcom,sm8450-dp
               - qcom,sm8550-dp
-- 
2.39.2

[PATCH 2/9] arm64: dts: qcom: sm8150: use SoC-specific compat for RPMh stats

[Dmitry Baryshkov]

The SM8150 platform doesn't support DDR sleep stats, so it needs
SoC-specific compat string for the RPMh stats data.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index 3cba87e00123..fb41f91cefc6 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -3950,7 +3950,7 @@ aoss_qmp: power-management@c300000 {
 		};
 
 		sram@c3f0000 {
-			compatible = "qcom,rpmh-stats";
+			compatible = "qcom,sm8150-rpmh-stats";
 			reg = <0 0x0c3f0000 0 0x400>;
 		};
 
-- 
2.39.2

[PATCH 2/9] arm64: dts: qcom: sm8150: use SoC-specific compat for RPMh stats

[Dmitry Baryshkov]

The SM8150 platform doesn't support DDR sleep stats, so it needs
SoC-specific compat string for the RPMh stats data.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index 3cba87e00123..fb41f91cefc6 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -3950,7 +3950,7 @@ aoss_qmp: power-management@c300000 {
 		};
 
 		sram@c3f0000 {
-			compatible = "qcom,rpmh-stats";
+			compatible = "qcom,sm8150-rpmh-stats";
 			reg = <0 0x0c3f0000 0 0x400>;
 		};
 
-- 
2.39.2

[PATCH 3/9] arm64: dts: qcom: sm8150: make dispcc cast minimal vote on MMCX

[Dmitry Baryshkov]

Add required-opps property to the display clock controller. This makes
it cast minimal vote on the MMCX lane and prevents further 'clock stuck'
errors when enabling the display.

Fixes: 2ef3bb17c45c ("arm64: dts: qcom: sm8150: Add DISPCC node")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index fb41f91cefc6..153c531c1d41 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -3925,6 +3925,7 @@ dispcc: clock-controller@af00000 {
 				      "dp_phy_pll_link_clk",
 				      "dp_phy_pll_vco_div_clk";
 			power-domains = <&rpmhpd SM8150_MMCX>;
+			required-opps = <&rpmhpd_opp_low_svs>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
-- 
2.39.2

[PATCH 3/9] arm64: dts: qcom: sm8150: make dispcc cast minimal vote on MMCX

[Dmitry Baryshkov]

Add required-opps property to the display clock controller. This makes
it cast minimal vote on the MMCX lane and prevents further 'clock stuck'
errors when enabling the display.

Fixes: 2ef3bb17c45c ("arm64: dts: qcom: sm8150: Add DISPCC node")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index fb41f91cefc6..153c531c1d41 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -3925,6 +3925,7 @@ dispcc: clock-controller@af00000 {
 				      "dp_phy_pll_link_clk",
 				      "dp_phy_pll_vco_div_clk";
 			power-domains = <&rpmhpd SM8150_MMCX>;
+			required-opps = <&rpmhpd_opp_low_svs>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
-- 
2.39.2

[PATCH 4/9] arm64: dts: qcom: sm8150-hdk: enable HDMI output

[Dmitry Baryshkov]

Add DSI outputs and link them to the onboard Lontium LT9611 DSI-to-HDMI
bridge, enabling HDMI output on this board. While adding the display
resources, also drop the headless ("amd,imageon") compat string from the
GPU node, since the board now has output.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150-hdk.dts | 128 +++++++++++++++++++++++-
 1 file changed, 123 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
index bb161b536da4..6a036f9ba1c9 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
@@ -54,6 +54,17 @@ key-vol-up {
 			gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>;
 		};
 	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&lt9611_out>;
+			};
+		};
+	};
 };
 
 &apps_rsc {
@@ -359,12 +370,112 @@ &gmu {
 	status = "okay";
 };
 
+&gpi_dma1 {
+	status = "okay";
+};
+
 &gpu {
-	/*
-	 * NOTE: "amd,imageon" makes Adreno start in headless mode, remove it
-	 * after display support is added on this board.
-	 */
-	compatible = "qcom,adreno-640.1", "qcom,adreno", "amd,imageon";
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	lt9611_codec: hdmi-bridge@3b {
+		compatible = "lontium,lt9611";
+		reg = <0x3b>;
+		#sound-dai-cells = <1>;
+
+		interrupts-extended = <&tlmm 9 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&vreg_s4a_1p8>;
+		vcc-supply = <&vreg_bob>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lt9611_irq_pin>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lt9611_a: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lt9611_b: endpoint {
+					remote-endpoint = <&mdss_dsi1_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				lt9611_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	status = "okay";
+	vdda-supply = <&vreg_l3c_1p2>;
+
+	qcom,dual-dsi-mode;
+	qcom,master-dsi;
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&lt9611_a>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_phy {
+	status = "okay";
+	vdds-supply = <&vreg_l5a_0p875>;
+};
+
+&mdss_dsi1 {
+	vdda-supply = <&vreg_l3c_1p2>;
+
+	qcom,dual-dsi-mode;
+
+	/* DSI1 is slave, so use DSI0 clocks */
+	assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;
+
+	status = "okay";
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&lt9611_b>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&mdss_dsi1_phy {
+	vdds-supply = <&vreg_l5a_0p875>;
 	status = "okay";
 };
 
@@ -402,6 +513,13 @@ &remoteproc_slpi {
 
 &tlmm {
 	gpio-reserved-ranges = <0 4>, <126 4>;
+
+	lt9611_irq_pin: lt9611-irq-state {
+		pins = "gpio9";
+		function = "gpio";
+		bias-disable;
+	};
+
 };
 
 &uart2 {
-- 
2.39.2

[PATCH 4/9] arm64: dts: qcom: sm8150-hdk: enable HDMI output

[Dmitry Baryshkov]

Add DSI outputs and link them to the onboard Lontium LT9611 DSI-to-HDMI
bridge, enabling HDMI output on this board. While adding the display
resources, also drop the headless ("amd,imageon") compat string from the
GPU node, since the board now has output.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150-hdk.dts | 128 +++++++++++++++++++++++-
 1 file changed, 123 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
index bb161b536da4..6a036f9ba1c9 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
@@ -54,6 +54,17 @@ key-vol-up {
 			gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>;
 		};
 	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&lt9611_out>;
+			};
+		};
+	};
 };
 
 &apps_rsc {
@@ -359,12 +370,112 @@ &gmu {
 	status = "okay";
 };
 
+&gpi_dma1 {
+	status = "okay";
+};
+
 &gpu {
-	/*
-	 * NOTE: "amd,imageon" makes Adreno start in headless mode, remove it
-	 * after display support is added on this board.
-	 */
-	compatible = "qcom,adreno-640.1", "qcom,adreno", "amd,imageon";
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	lt9611_codec: hdmi-bridge@3b {
+		compatible = "lontium,lt9611";
+		reg = <0x3b>;
+		#sound-dai-cells = <1>;
+
+		interrupts-extended = <&tlmm 9 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&vreg_s4a_1p8>;
+		vcc-supply = <&vreg_bob>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lt9611_irq_pin>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lt9611_a: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lt9611_b: endpoint {
+					remote-endpoint = <&mdss_dsi1_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				lt9611_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	status = "okay";
+	vdda-supply = <&vreg_l3c_1p2>;
+
+	qcom,dual-dsi-mode;
+	qcom,master-dsi;
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&lt9611_a>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_phy {
+	status = "okay";
+	vdds-supply = <&vreg_l5a_0p875>;
+};
+
+&mdss_dsi1 {
+	vdda-supply = <&vreg_l3c_1p2>;
+
+	qcom,dual-dsi-mode;
+
+	/* DSI1 is slave, so use DSI0 clocks */
+	assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;
+
+	status = "okay";
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&lt9611_b>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&mdss_dsi1_phy {
+	vdds-supply = <&vreg_l5a_0p875>;
 	status = "okay";
 };
 
@@ -402,6 +513,13 @@ &remoteproc_slpi {
 
 &tlmm {
 	gpio-reserved-ranges = <0 4>, <126 4>;
+
+	lt9611_irq_pin: lt9611-irq-state {
+		pins = "gpio9";
+		function = "gpio";
+		bias-disable;
+	};
+
 };
 
 &uart2 {
-- 
2.39.2

[PATCH 5/9] arm64: dts: qcom: sm8150-hdk: fix SS USB regulators

[Dmitry Baryshkov]

The SM8150-HDK uses two different regulators to power up SuperSpeed USB
PHYs. The L5A regulator is used for the second USB host, while the first
(OTG) USB host uses different regulator, L18A. Fix the regulator for the
usb_1 QMPPHY and (to remove possible confusion) drop the
usb_ss_dp_core_1/_2 labels.

Fixes: 0ab1b2d10afe ("arm64: dts: qcom: add sm8150 hdk dts")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150-hdk.dts | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
index 6a036f9ba1c9..ea4d75308ac8 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
@@ -138,8 +138,6 @@ vdda_qrefs_0p875_5:
 		vdda_sp_sensor:
 		vdda_ufs_2ln_core_1:
 		vdda_ufs_2ln_core_2:
-		vdda_usb_ss_dp_core_1:
-		vdda_usb_ss_dp_core_2:
 		vdda_qlink_lv:
 		vdda_qlink_lv_ck:
 		vreg_l5a_0p875: ldo5 {
@@ -221,6 +219,12 @@ vreg_l17a_3p0: ldo17 {
 			regulator-max-microvolt = <3008000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 		};
+
+		vreg_l18a_0p8: ldo18 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
 	};
 
 	regulators-1 {
@@ -563,13 +567,13 @@ &usb_2_hsphy {
 &usb_1_qmpphy {
 	status = "okay";
 	vdda-phy-supply = <&vreg_l3c_1p2>;
-	vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
+	vdda-pll-supply = <&vreg_l18a_0p8>;
 };
 
 &usb_2_qmpphy {
 	status = "okay";
 	vdda-phy-supply = <&vreg_l3c_1p2>;
-	vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
+	vdda-pll-supply = <&vreg_l5a_0p875>;
 };
 
 &usb_1 {
-- 
2.39.2

[PATCH 5/9] arm64: dts: qcom: sm8150-hdk: fix SS USB regulators

[Dmitry Baryshkov]

The SM8150-HDK uses two different regulators to power up SuperSpeed USB
PHYs. The L5A regulator is used for the second USB host, while the first
(OTG) USB host uses different regulator, L18A. Fix the regulator for the
usb_1 QMPPHY and (to remove possible confusion) drop the
usb_ss_dp_core_1/_2 labels.

Fixes: 0ab1b2d10afe ("arm64: dts: qcom: add sm8150 hdk dts")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150-hdk.dts | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
index 6a036f9ba1c9..ea4d75308ac8 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
@@ -138,8 +138,6 @@ vdda_qrefs_0p875_5:
 		vdda_sp_sensor:
 		vdda_ufs_2ln_core_1:
 		vdda_ufs_2ln_core_2:
-		vdda_usb_ss_dp_core_1:
-		vdda_usb_ss_dp_core_2:
 		vdda_qlink_lv:
 		vdda_qlink_lv_ck:
 		vreg_l5a_0p875: ldo5 {
@@ -221,6 +219,12 @@ vreg_l17a_3p0: ldo17 {
 			regulator-max-microvolt = <3008000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 		};
+
+		vreg_l18a_0p8: ldo18 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
 	};
 
 	regulators-1 {
@@ -563,13 +567,13 @@ &usb_2_hsphy {
 &usb_1_qmpphy {
 	status = "okay";
 	vdda-phy-supply = <&vreg_l3c_1p2>;
-	vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
+	vdda-pll-supply = <&vreg_l18a_0p8>;
 };
 
 &usb_2_qmpphy {
 	status = "okay";
 	vdda-phy-supply = <&vreg_l3c_1p2>;
-	vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
+	vdda-pll-supply = <&vreg_l5a_0p875>;
 };
 
 &usb_1 {
-- 
2.39.2

[PATCH 6/9] arm64: dts: qcom: sm8150: add DisplayPort controller

[Dmitry Baryshkov]

Add device tree node for the DisplayPort controller and link it to the
display controller interface.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150.dtsi | 87 ++++++++++++++++++++++++++++
 1 file changed, 87 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index 153c531c1d41..ea7c92c0e405 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -3712,6 +3712,13 @@ dpu_intf2_out: endpoint {
 							remote-endpoint = <&mdss_dsi1_in>;
 						};
 					};
+
+					port@2 {
+						reg = <2>;
+						dpu_intf0_out: endpoint {
+							remote-endpoint = <&mdss_dp_in>;
+						};
+					};
 				};
 
 				mdp_opp_table: opp-table {
@@ -3739,6 +3746,86 @@ opp-460000000 {
 				};
 			};
 
+			mdss_dp: displayport-controller@ae90000 {
+				compatible = "qcom,sm8150-dp", "qcom,sm8350-dp";
+				reg = <0 0xae90000 0 0x200>,
+				      <0 0xae90200 0 0x200>,
+				      <0 0xae90400 0 0x600>,
+				      <0 0x0ae90a00 0 0x600>,
+				      <0 0x0ae91000 0 0x600>;
+
+				interrupt-parent = <&mdss>;
+				interrupts = <12>;
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
+				clock-names = "core_iface",
+					      "core_aux",
+					      "ctrl_link",
+					      "ctrl_link_iface",
+					      "stream_pixel";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
+				assigned-clock-parents = <&usb_1_qmpphy QMP_USB43DP_DP_LINK_CLK>,
+							 <&usb_1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;
+
+				phys = <&usb_1_qmpphy QMP_USB43DP_DP_PHY>;
+				phy-names = "dp";
+
+				#sound-dai-cells = <0>;
+
+				operating-points-v2 = <&dp_opp_table>;
+				power-domains = <&rpmhpd SM8250_MMCX>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_dp_in: endpoint {
+							remote-endpoint = <&dpu_intf0_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						mdss_dp_out: endpoint {
+						};
+					};
+				};
+
+				dp_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-160000000 {
+						opp-hz = /bits/ 64 <160000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-270000000 {
+						opp-hz = /bits/ 64 <270000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-540000000 {
+						opp-hz = /bits/ 64 <540000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-810000000 {
+						opp-hz = /bits/ 64 <810000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
 			mdss_dsi0: dsi@ae94000 {
 				compatible = "qcom,sm8150-dsi-ctrl", "qcom,mdss-dsi-ctrl";
 				reg = <0 0x0ae94000 0 0x400>;
-- 
2.39.2

[PATCH 6/9] arm64: dts: qcom: sm8150: add DisplayPort controller

[Dmitry Baryshkov]

Add device tree node for the DisplayPort controller and link it to the
display controller interface.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150.dtsi | 87 ++++++++++++++++++++++++++++
 1 file changed, 87 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index 153c531c1d41..ea7c92c0e405 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -3712,6 +3712,13 @@ dpu_intf2_out: endpoint {
 							remote-endpoint = <&mdss_dsi1_in>;
 						};
 					};
+
+					port@2 {
+						reg = <2>;
+						dpu_intf0_out: endpoint {
+							remote-endpoint = <&mdss_dp_in>;
+						};
+					};
 				};
 
 				mdp_opp_table: opp-table {
@@ -3739,6 +3746,86 @@ opp-460000000 {
 				};
 			};
 
+			mdss_dp: displayport-controller@ae90000 {
+				compatible = "qcom,sm8150-dp", "qcom,sm8350-dp";
+				reg = <0 0xae90000 0 0x200>,
+				      <0 0xae90200 0 0x200>,
+				      <0 0xae90400 0 0x600>,
+				      <0 0x0ae90a00 0 0x600>,
+				      <0 0x0ae91000 0 0x600>;
+
+				interrupt-parent = <&mdss>;
+				interrupts = <12>;
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
+				clock-names = "core_iface",
+					      "core_aux",
+					      "ctrl_link",
+					      "ctrl_link_iface",
+					      "stream_pixel";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
+				assigned-clock-parents = <&usb_1_qmpphy QMP_USB43DP_DP_LINK_CLK>,
+							 <&usb_1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;
+
+				phys = <&usb_1_qmpphy QMP_USB43DP_DP_PHY>;
+				phy-names = "dp";
+
+				#sound-dai-cells = <0>;
+
+				operating-points-v2 = <&dp_opp_table>;
+				power-domains = <&rpmhpd SM8250_MMCX>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_dp_in: endpoint {
+							remote-endpoint = <&dpu_intf0_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						mdss_dp_out: endpoint {
+						};
+					};
+				};
+
+				dp_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-160000000 {
+						opp-hz = /bits/ 64 <160000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-270000000 {
+						opp-hz = /bits/ 64 <270000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-540000000 {
+						opp-hz = /bits/ 64 <540000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-810000000 {
+						opp-hz = /bits/ 64 <810000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
 			mdss_dsi0: dsi@ae94000 {
 				compatible = "qcom,sm8150-dsi-ctrl", "qcom,mdss-dsi-ctrl";
 				reg = <0 0x0ae94000 0 0x400>;
-- 
2.39.2

[PATCH 7/9] arm64: dts: qcom: sm8150: add USB-C ports to the USB+DP QMP PHY

[Dmitry Baryshkov]

Expand Combo USB+DP QMP PHY device node with the OF ports required to
support USB-C / DisplayPort switching.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150.dtsi | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index ea7c92c0e405..38423a9f8408 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -3447,6 +3447,29 @@ usb_1_qmpphy: phy@88e8000 {
 			#phy-cells = <1>;
 
 			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					usb_1_qmpphy_out: endpoint {};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					usb_1_qmpphy_usb_ss_in: endpoint {
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					usb_1_qmpphy_dp_in: endpoint {};
+				};
+			};
 		};
 
 		usb_2_qmpphy: phy@88eb000 {
-- 
2.39.2

[PATCH 7/9] arm64: dts: qcom: sm8150: add USB-C ports to the USB+DP QMP PHY

[Dmitry Baryshkov]

Expand Combo USB+DP QMP PHY device node with the OF ports required to
support USB-C / DisplayPort switching.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150.dtsi | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index ea7c92c0e405..38423a9f8408 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -3447,6 +3447,29 @@ usb_1_qmpphy: phy@88e8000 {
 			#phy-cells = <1>;
 
 			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					usb_1_qmpphy_out: endpoint {};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					usb_1_qmpphy_usb_ss_in: endpoint {
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					usb_1_qmpphy_dp_in: endpoint {};
+				};
+			};
 		};
 
 		usb_2_qmpphy: phy@88eb000 {
-- 
2.39.2

[PATCH 8/9] arm64: dts: qcom: sm8150: add USB-C ports to the OTG USB host

[Dmitry Baryshkov]

Expand first USB host controller device node with the OF ports required
to support USB-C / DisplayPort switching.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index 38423a9f8408..84f61e018d78 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -3605,6 +3605,25 @@ usb_1_dwc3: usb@a600000 {
 				snps,dis_enblslpm_quirk;
 				phys = <&usb_1_hsphy>, <&usb_1_qmpphy QMP_USB43DP_USB3_PHY>;
 				phy-names = "usb2-phy", "usb3-phy";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						usb_1_dwc3_hs: endpoint {
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						usb_1_dwc3_ss: endpoint {
+						};
+					};
+				};
 			};
 		};
 
-- 
2.39.2

[PATCH 8/9] arm64: dts: qcom: sm8150: add USB-C ports to the OTG USB host

[Dmitry Baryshkov]

Expand first USB host controller device node with the OF ports required
to support USB-C / DisplayPort switching.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index 38423a9f8408..84f61e018d78 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -3605,6 +3605,25 @@ usb_1_dwc3: usb@a600000 {
 				snps,dis_enblslpm_quirk;
 				phys = <&usb_1_hsphy>, <&usb_1_qmpphy QMP_USB43DP_USB3_PHY>;
 				phy-names = "usb2-phy", "usb3-phy";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						usb_1_dwc3_hs: endpoint {
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						usb_1_dwc3_ss: endpoint {
+						};
+					};
+				};
 			};
 		};
 
-- 
2.39.2

[PATCH 9/9] arm64: dts: qcom: sm8150-hdk: enable DisplayPort and USB-C altmode

[Dmitry Baryshkov]

Enable the USB-C related functionality for the USB-C port on this board.
This includes OTG, PowerDelivery and DP AltMode. Also enable the
DisplayPort itself.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150-hdk.dts | 124 +++++++++++++++++++++++-
 1 file changed, 123 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
index ea4d75308ac8..3b9499b0bbe8 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
@@ -7,6 +7,7 @@
 
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/usb/pd.h>
 #include "sm8150.dtsi"
 #include "pm8150.dtsi"
 #include "pm8150b.dtsi"
@@ -374,6 +375,10 @@ &gmu {
 	status = "okay";
 };
 
+&gpi_dma0 {
+	status = "okay";
+};
+
 &gpi_dma1 {
 	status = "okay";
 };
@@ -382,6 +387,29 @@ &gpu {
 	status = "okay";
 };
 
+&i2c4 {
+	clock-frequency = <100000>;
+
+	status = "okay";
+
+	typec-mux@42 {
+		compatible = "fcs,fsa4480";
+		reg = <0x42>;
+
+		interrupts-extended = <&tlmm 152 IRQ_TYPE_LEVEL_LOW>;
+
+		vcc-supply = <&vreg_bob>;
+		mode-switch;
+		orientation-switch;
+
+		port {
+			fsa4480_sbu_mux: endpoint {
+				remote-endpoint = <&pm8150b_typec_sbu_out>;
+			};
+		};
+	};
+};
+
 &i2c9 {
 	status = "okay";
 	clock-frequency = <400000>;
@@ -436,6 +464,15 @@ &mdss {
 	status = "okay";
 };
 
+&mdss_dp {
+	status = "okay";
+};
+
+&mdss_dp_out {
+	data-lanes = <0 1>;
+	remote-endpoint = <&usb_1_qmpphy_dp_in>;
+};
+
 &mdss_dsi0 {
 	status = "okay";
 	vdda-supply = <&vreg_l3c_1p2>;
@@ -483,6 +520,65 @@ &mdss_dsi1_phy {
 	status = "okay";
 };
 
+&pm8150b_vbus {
+	regulator-min-microamp = <500000>;
+	regulator-max-microamp = <3000000>;
+	status = "okay";
+};
+
+&pm8150b_typec {
+	status = "okay";
+
+	vdd-pdphy-supply = <&vreg_l2a_3p1>;
+
+	connector {
+		compatible = "usb-c-connector";
+
+		power-role = "source";
+		data-role = "dual";
+		self-powered;
+
+		source-pdos = <PDO_FIXED(5000, 3000,
+					 PDO_FIXED_DUAL_ROLE |
+					 PDO_FIXED_USB_COMM |
+					 PDO_FIXED_DATA_SWAP)>;
+
+		altmodes {
+			displayport {
+				svid = <0xff01>;
+				vdo = <0x00001c46>;
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				pm8150b_role_switch_in: endpoint {
+					remote-endpoint = <&usb_1_dwc3_hs>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				pm8150b_typec_mux_in: endpoint {
+					remote-endpoint = <&usb_1_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				pm8150b_typec_sbu_out: endpoint {
+					remote-endpoint = <&fsa4480_sbu_mux>;
+				};
+			};
+		};
+	};
+};
+
 &pon_pwrkey {
 	status = "okay";
 };
@@ -493,6 +589,10 @@ &pon_resin {
 	linux,code = <KEY_VOLUMEDOWN>;
 };
 
+&qupv3_id_0 {
+	status = "okay";
+};
+
 &qupv3_id_1 {
 	status = "okay";
 };
@@ -568,6 +668,19 @@ &usb_1_qmpphy {
 	status = "okay";
 	vdda-phy-supply = <&vreg_l3c_1p2>;
 	vdda-pll-supply = <&vreg_l18a_0p8>;
+	orientation-switch;
+};
+
+&usb_1_qmpphy_dp_in {
+	remote-endpoint = <&mdss_dp_out>;
+};
+
+&usb_1_qmpphy_out {
+	remote-endpoint = <&pm8150b_typec_mux_in>;
+};
+
+&usb_1_qmpphy_usb_ss_in {
+	remote-endpoint = <&usb_1_dwc3_ss>;
 };
 
 &usb_2_qmpphy {
@@ -585,7 +698,16 @@ &usb_2 {
 };
 
 &usb_1_dwc3 {
-	dr_mode = "peripheral";
+	dr_mode = "otg";
+	usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+	remote-endpoint = <&pm8150b_role_switch_in>;
+};
+
+&usb_1_dwc3_ss {
+	remote-endpoint = <&usb_1_qmpphy_usb_ss_in>;
 };
 
 &usb_2_dwc3 {
-- 
2.39.2

[PATCH 9/9] arm64: dts: qcom: sm8150-hdk: enable DisplayPort and USB-C altmode

[Dmitry Baryshkov]

Enable the USB-C related functionality for the USB-C port on this board.
This includes OTG, PowerDelivery and DP AltMode. Also enable the
DisplayPort itself.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150-hdk.dts | 124 +++++++++++++++++++++++-
 1 file changed, 123 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
index ea4d75308ac8..3b9499b0bbe8 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
@@ -7,6 +7,7 @@
 
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/usb/pd.h>
 #include "sm8150.dtsi"
 #include "pm8150.dtsi"
 #include "pm8150b.dtsi"
@@ -374,6 +375,10 @@ &gmu {
 	status = "okay";
 };
 
+&gpi_dma0 {
+	status = "okay";
+};
+
 &gpi_dma1 {
 	status = "okay";
 };
@@ -382,6 +387,29 @@ &gpu {
 	status = "okay";
 };
 
+&i2c4 {
+	clock-frequency = <100000>;
+
+	status = "okay";
+
+	typec-mux@42 {
+		compatible = "fcs,fsa4480";
+		reg = <0x42>;
+
+		interrupts-extended = <&tlmm 152 IRQ_TYPE_LEVEL_LOW>;
+
+		vcc-supply = <&vreg_bob>;
+		mode-switch;
+		orientation-switch;
+
+		port {
+			fsa4480_sbu_mux: endpoint {
+				remote-endpoint = <&pm8150b_typec_sbu_out>;
+			};
+		};
+	};
+};
+
 &i2c9 {
 	status = "okay";
 	clock-frequency = <400000>;
@@ -436,6 +464,15 @@ &mdss {
 	status = "okay";
 };
 
+&mdss_dp {
+	status = "okay";
+};
+
+&mdss_dp_out {
+	data-lanes = <0 1>;
+	remote-endpoint = <&usb_1_qmpphy_dp_in>;
+};
+
 &mdss_dsi0 {
 	status = "okay";
 	vdda-supply = <&vreg_l3c_1p2>;
@@ -483,6 +520,65 @@ &mdss_dsi1_phy {
 	status = "okay";
 };
 
+&pm8150b_vbus {
+	regulator-min-microamp = <500000>;
+	regulator-max-microamp = <3000000>;
+	status = "okay";
+};
+
+&pm8150b_typec {
+	status = "okay";
+
+	vdd-pdphy-supply = <&vreg_l2a_3p1>;
+
+	connector {
+		compatible = "usb-c-connector";
+
+		power-role = "source";
+		data-role = "dual";
+		self-powered;
+
+		source-pdos = <PDO_FIXED(5000, 3000,
+					 PDO_FIXED_DUAL_ROLE |
+					 PDO_FIXED_USB_COMM |
+					 PDO_FIXED_DATA_SWAP)>;
+
+		altmodes {
+			displayport {
+				svid = <0xff01>;
+				vdo = <0x00001c46>;
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				pm8150b_role_switch_in: endpoint {
+					remote-endpoint = <&usb_1_dwc3_hs>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				pm8150b_typec_mux_in: endpoint {
+					remote-endpoint = <&usb_1_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				pm8150b_typec_sbu_out: endpoint {
+					remote-endpoint = <&fsa4480_sbu_mux>;
+				};
+			};
+		};
+	};
+};
+
 &pon_pwrkey {
 	status = "okay";
 };
@@ -493,6 +589,10 @@ &pon_resin {
 	linux,code = <KEY_VOLUMEDOWN>;
 };
 
+&qupv3_id_0 {
+	status = "okay";
+};
+
 &qupv3_id_1 {
 	status = "okay";
 };
@@ -568,6 +668,19 @@ &usb_1_qmpphy {
 	status = "okay";
 	vdda-phy-supply = <&vreg_l3c_1p2>;
 	vdda-pll-supply = <&vreg_l18a_0p8>;
+	orientation-switch;
+};
+
+&usb_1_qmpphy_dp_in {
+	remote-endpoint = <&mdss_dp_out>;
+};
+
+&usb_1_qmpphy_out {
+	remote-endpoint = <&pm8150b_typec_mux_in>;
+};
+
+&usb_1_qmpphy_usb_ss_in {
+	remote-endpoint = <&usb_1_dwc3_ss>;
 };
 
 &usb_2_qmpphy {
@@ -585,7 +698,16 @@ &usb_2 {
 };
 
 &usb_1_dwc3 {
-	dr_mode = "peripheral";
+	dr_mode = "otg";
+	usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+	remote-endpoint = <&pm8150b_role_switch_in>;
+};
+
+&usb_1_dwc3_ss {
+	remote-endpoint = <&usb_1_qmpphy_usb_ss_in>;
 };
 
 &usb_2_dwc3 {
-- 
2.39.2

Re: [PATCH 2/9] arm64: dts: qcom: sm8150: use SoC-specific compat for RPMh stats

[Konrad Dybcio]

On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> The SM8150 platform doesn't support DDR sleep stats, so it needs
> SoC-specific compat string for the RPMh stats data.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
Not a fan, see my comments over at [1].

Konrad

[1] https://lore.kernel.org/linux-arm-msm/20231209215601.3543895-1-dmitry.baryshkov@linaro.org/T/#t

Re: [PATCH 2/9] arm64: dts: qcom: sm8150: use SoC-specific compat for RPMh stats

[Konrad Dybcio]

On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> The SM8150 platform doesn't support DDR sleep stats, so it needs
> SoC-specific compat string for the RPMh stats data.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
Not a fan, see my comments over at [1].

Konrad

[1] https://lore.kernel.org/linux-arm-msm/20231209215601.3543895-1-dmitry.baryshkov@linaro.org/T/#t

Re: [PATCH 3/9] arm64: dts: qcom: sm8150: make dispcc cast minimal vote on MMCX

[Konrad Dybcio]

On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> Add required-opps property to the display clock controller. This makes
> it cast minimal vote on the MMCX lane and prevents further 'clock stuck'
> errors when enabling the display.
> 
> Fixes: 2ef3bb17c45c ("arm64: dts: qcom: sm8150: Add DISPCC node")
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

Re: [PATCH 3/9] arm64: dts: qcom: sm8150: make dispcc cast minimal vote on MMCX

[Konrad Dybcio]

On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> Add required-opps property to the display clock controller. This makes
> it cast minimal vote on the MMCX lane and prevents further 'clock stuck'
> errors when enabling the display.
> 
> Fixes: 2ef3bb17c45c ("arm64: dts: qcom: sm8150: Add DISPCC node")
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

Re: [PATCH 4/9] arm64: dts: qcom: sm8150-hdk: enable HDMI output

[Konrad Dybcio]

On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> Add DSI outputs and link them to the onboard Lontium LT9611 DSI-to-HDMI
> bridge, enabling HDMI output on this board. While adding the display
> resources, also drop the headless ("amd,imageon") compat string from the
> GPU node, since the board now has output.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
[...]


> +
> +	lt9611_irq_pin: lt9611-irq-state {
> +		pins = "gpio9";
> +		function = "gpio";
> +		bias-disable;
No drive-strength?

Otherwise lokos good at a glance!

Konrad

Re: [PATCH 4/9] arm64: dts: qcom: sm8150-hdk: enable HDMI output

[Konrad Dybcio]

On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> Add DSI outputs and link them to the onboard Lontium LT9611 DSI-to-HDMI
> bridge, enabling HDMI output on this board. While adding the display
> resources, also drop the headless ("amd,imageon") compat string from the
> GPU node, since the board now has output.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
[...]


> +
> +	lt9611_irq_pin: lt9611-irq-state {
> +		pins = "gpio9";
> +		function = "gpio";
> +		bias-disable;
No drive-strength?

Otherwise lokos good at a glance!

Konrad

Re: [PATCH 5/9] arm64: dts: qcom: sm8150-hdk: fix SS USB regulators

[Konrad Dybcio]

On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> The SM8150-HDK uses two different regulators to power up SuperSpeed USB
> PHYs. The L5A regulator is used for the second USB host, while the first
> (OTG) USB host uses different regulator, L18A. Fix the regulator for the
> usb_1 QMPPHY and (to remove possible confusion) drop the
> usb_ss_dp_core_1/_2 labels.
> 
> Fixes: 0ab1b2d10afe ("arm64: dts: qcom: add sm8150 hdk dts")
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

Re: [PATCH 5/9] arm64: dts: qcom: sm8150-hdk: fix SS USB regulators

[Konrad Dybcio]

On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> The SM8150-HDK uses two different regulators to power up SuperSpeed USB
> PHYs. The L5A regulator is used for the second USB host, while the first
> (OTG) USB host uses different regulator, L18A. Fix the regulator for the
> usb_1 QMPPHY and (to remove possible confusion) drop the
> usb_ss_dp_core_1/_2 labels.
> 
> Fixes: 0ab1b2d10afe ("arm64: dts: qcom: add sm8150 hdk dts")
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

Re: [PATCH 7/9] arm64: dts: qcom: sm8150: add USB-C ports to the USB+DP QMP PHY

[Konrad Dybcio]

On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> Expand Combo USB+DP QMP PHY device node with the OF ports required to
> support USB-C / DisplayPort switching.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm8150.dtsi | 23 +++++++++++++++++++++++
>  1 file changed, 23 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
> index ea7c92c0e405..38423a9f8408 100644
> --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
> @@ -3447,6 +3447,29 @@ usb_1_qmpphy: phy@88e8000 {
>  			#phy-cells = <1>;
>  
>  			status = "disabled";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				port@0 {
> +					reg = <0>;
> +					usb_1_qmpphy_out: endpoint {};
style 1
> +				};
> +
> +				port@1 {
> +					reg = <1>;
> +
> +					usb_1_qmpphy_usb_ss_in: endpoint {
> +					};
style 2
> +				};
> +
> +				port@2 {
> +					reg = <2>;
> +
> +					usb_1_qmpphy_dp_in: endpoint {};
style 3

:(

Konrad

Re: [PATCH 7/9] arm64: dts: qcom: sm8150: add USB-C ports to the USB+DP QMP PHY

[Konrad Dybcio]

On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> Expand Combo USB+DP QMP PHY device node with the OF ports required to
> support USB-C / DisplayPort switching.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm8150.dtsi | 23 +++++++++++++++++++++++
>  1 file changed, 23 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
> index ea7c92c0e405..38423a9f8408 100644
> --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
> @@ -3447,6 +3447,29 @@ usb_1_qmpphy: phy@88e8000 {
>  			#phy-cells = <1>;
>  
>  			status = "disabled";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				port@0 {
> +					reg = <0>;
> +					usb_1_qmpphy_out: endpoint {};
style 1
> +				};
> +
> +				port@1 {
> +					reg = <1>;
> +
> +					usb_1_qmpphy_usb_ss_in: endpoint {
> +					};
style 2
> +				};
> +
> +				port@2 {
> +					reg = <2>;
> +
> +					usb_1_qmpphy_dp_in: endpoint {};
style 3

:(

Konrad

Re: [PATCH 9/9] arm64: dts: qcom: sm8150-hdk: enable DisplayPort and USB-C altmode

[Konrad Dybcio]

On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> Enable the USB-C related functionality for the USB-C port on this board.
> This includes OTG, PowerDelivery and DP AltMode. Also enable the
> DisplayPort itself.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
[...]

> +&pm8150b_typec {
> +	status = "okay";
> +
> +	vdd-pdphy-supply = <&vreg_l2a_3p1>;
> +
> +	connector {
> +		compatible = "usb-c-connector";
> +
> +		power-role = "source";
> +		data-role = "dual";
> +		self-powered;
> +
> +		source-pdos = <PDO_FIXED(5000, 3000,
> +					 PDO_FIXED_DUAL_ROLE |
> +					 PDO_FIXED_USB_COMM |
> +					 PDO_FIXED_DATA_SWAP)>;
> +
> +		altmodes {
> +			displayport {
> +				svid = <0xff01>;
/bits/ 16?

Konrad

Re: [PATCH 9/9] arm64: dts: qcom: sm8150-hdk: enable DisplayPort and USB-C altmode

[Konrad Dybcio]

On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> Enable the USB-C related functionality for the USB-C port on this board.
> This includes OTG, PowerDelivery and DP AltMode. Also enable the
> DisplayPort itself.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
[...]

> +&pm8150b_typec {
> +	status = "okay";
> +
> +	vdd-pdphy-supply = <&vreg_l2a_3p1>;
> +
> +	connector {
> +		compatible = "usb-c-connector";
> +
> +		power-role = "source";
> +		data-role = "dual";
> +		self-powered;
> +
> +		source-pdos = <PDO_FIXED(5000, 3000,
> +					 PDO_FIXED_DUAL_ROLE |
> +					 PDO_FIXED_USB_COMM |
> +					 PDO_FIXED_DATA_SWAP)>;
> +
> +		altmodes {
> +			displayport {
> +				svid = <0xff01>;
/bits/ 16?

Konrad

Re: [PATCH 4/9] arm64: dts: qcom: sm8150-hdk: enable HDMI output

[Dmitry Baryshkov]

On Mon, 11 Dec 2023 at 11:31, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>
> On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> > Add DSI outputs and link them to the onboard Lontium LT9611 DSI-to-HDMI
> > bridge, enabling HDMI output on this board. While adding the display
> > resources, also drop the headless ("amd,imageon") compat string from the
> > GPU node, since the board now has output.
> >
> > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> > ---
> [...]
>
>
> > +
> > +     lt9611_irq_pin: lt9611-irq-state {
> > +             pins = "gpio9";
> > +             function = "gpio";
> > +             bias-disable;
> No drive-strength?

For the input pin with no bias? I'm not sure. And yes, it was c&p from RB3.

> Otherwise lokos good at a glance!


-- 
With best wishes
Dmitry

Re: [PATCH 4/9] arm64: dts: qcom: sm8150-hdk: enable HDMI output

[Dmitry Baryshkov]

On Mon, 11 Dec 2023 at 11:31, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>
> On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> > Add DSI outputs and link them to the onboard Lontium LT9611 DSI-to-HDMI
> > bridge, enabling HDMI output on this board. While adding the display
> > resources, also drop the headless ("amd,imageon") compat string from the
> > GPU node, since the board now has output.
> >
> > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> > ---
> [...]
>
>
> > +
> > +     lt9611_irq_pin: lt9611-irq-state {
> > +             pins = "gpio9";
> > +             function = "gpio";
> > +             bias-disable;
> No drive-strength?

For the input pin with no bias? I'm not sure. And yes, it was c&p from RB3.

> Otherwise lokos good at a glance!


-- 
With best wishes
Dmitry

Re: [PATCH 7/9] arm64: dts: qcom: sm8150: add USB-C ports to the USB+DP QMP PHY

[Dmitry Baryshkov]

On Mon, 11 Dec 2023 at 11:33, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>
> On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> > Expand Combo USB+DP QMP PHY device node with the OF ports required to
> > support USB-C / DisplayPort switching.
> >
> > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> > ---
> >  arch/arm64/boot/dts/qcom/sm8150.dtsi | 23 +++++++++++++++++++++++
> >  1 file changed, 23 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
> > index ea7c92c0e405..38423a9f8408 100644
> > --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
> > @@ -3447,6 +3447,29 @@ usb_1_qmpphy: phy@88e8000 {
> >                       #phy-cells = <1>;
> >
> >                       status = "disabled";
> > +
> > +                     ports {
> > +                             #address-cells = <1>;
> > +                             #size-cells = <0>;
> > +
> > +                             port@0 {
> > +                                     reg = <0>;
> > +                                     usb_1_qmpphy_out: endpoint {};
> style 1
> > +                             };
> > +
> > +                             port@1 {
> > +                                     reg = <1>;
> > +
> > +                                     usb_1_qmpphy_usb_ss_in: endpoint {
> > +                                     };
> style 2
> > +                             };
> > +
> > +                             port@2 {
> > +                                     reg = <2>;
> > +
> > +                                     usb_1_qmpphy_dp_in: endpoint {};
> style 3
>
> :(

Which one should I stick to?


-- 
With best wishes
Dmitry

Re: [PATCH 7/9] arm64: dts: qcom: sm8150: add USB-C ports to the USB+DP QMP PHY

[Dmitry Baryshkov]

On Mon, 11 Dec 2023 at 11:33, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>
> On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> > Expand Combo USB+DP QMP PHY device node with the OF ports required to
> > support USB-C / DisplayPort switching.
> >
> > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> > ---
> >  arch/arm64/boot/dts/qcom/sm8150.dtsi | 23 +++++++++++++++++++++++
> >  1 file changed, 23 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
> > index ea7c92c0e405..38423a9f8408 100644
> > --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
> > @@ -3447,6 +3447,29 @@ usb_1_qmpphy: phy@88e8000 {
> >                       #phy-cells = <1>;
> >
> >                       status = "disabled";
> > +
> > +                     ports {
> > +                             #address-cells = <1>;
> > +                             #size-cells = <0>;
> > +
> > +                             port@0 {
> > +                                     reg = <0>;
> > +                                     usb_1_qmpphy_out: endpoint {};
> style 1
> > +                             };
> > +
> > +                             port@1 {
> > +                                     reg = <1>;
> > +
> > +                                     usb_1_qmpphy_usb_ss_in: endpoint {
> > +                                     };
> style 2
> > +                             };
> > +
> > +                             port@2 {
> > +                                     reg = <2>;
> > +
> > +                                     usb_1_qmpphy_dp_in: endpoint {};
> style 3
>
> :(

Which one should I stick to?


-- 
With best wishes
Dmitry

Re: [PATCH 9/9] arm64: dts: qcom: sm8150-hdk: enable DisplayPort and USB-C altmode

[Dmitry Baryshkov]

On Mon, 11 Dec 2023 at 11:33, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>
> On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> > Enable the USB-C related functionality for the USB-C port on this board.
> > This includes OTG, PowerDelivery and DP AltMode. Also enable the
> > DisplayPort itself.
> >
> > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> > ---
> [...]
>
> > +&pm8150b_typec {
> > +     status = "okay";
> > +
> > +     vdd-pdphy-supply = <&vreg_l2a_3p1>;
> > +
> > +     connector {
> > +             compatible = "usb-c-connector";
> > +
> > +             power-role = "source";
> > +             data-role = "dual";
> > +             self-powered;
> > +
> > +             source-pdos = <PDO_FIXED(5000, 3000,
> > +                                      PDO_FIXED_DUAL_ROLE |
> > +                                      PDO_FIXED_USB_COMM |
> > +                                      PDO_FIXED_DATA_SWAP)>;
> > +
> > +             altmodes {
> > +                     displayport {
> > +                             svid = <0xff01>;
> /bits/ 16?

Ugh, yes.

-- 
With best wishes
Dmitry

Re: [PATCH 9/9] arm64: dts: qcom: sm8150-hdk: enable DisplayPort and USB-C altmode

[Dmitry Baryshkov]

On Mon, 11 Dec 2023 at 11:33, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>
> On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> > Enable the USB-C related functionality for the USB-C port on this board.
> > This includes OTG, PowerDelivery and DP AltMode. Also enable the
> > DisplayPort itself.
> >
> > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> > ---
> [...]
>
> > +&pm8150b_typec {
> > +     status = "okay";
> > +
> > +     vdd-pdphy-supply = <&vreg_l2a_3p1>;
> > +
> > +     connector {
> > +             compatible = "usb-c-connector";
> > +
> > +             power-role = "source";
> > +             data-role = "dual";
> > +             self-powered;
> > +
> > +             source-pdos = <PDO_FIXED(5000, 3000,
> > +                                      PDO_FIXED_DUAL_ROLE |
> > +                                      PDO_FIXED_USB_COMM |
> > +                                      PDO_FIXED_DATA_SWAP)>;
> > +
> > +             altmodes {
> > +                     displayport {
> > +                             svid = <0xff01>;
> /bits/ 16?

Ugh, yes.

-- 
With best wishes
Dmitry

Re: [PATCH 7/9] arm64: dts: qcom: sm8150: add USB-C ports to the USB+DP QMP PHY

[Konrad Dybcio]

On 11.12.2023 10:46, Dmitry Baryshkov wrote:
> On Mon, 11 Dec 2023 at 11:33, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>>
>> On 10.12.2023 00:21, Dmitry Baryshkov wrote:
>>> Expand Combo USB+DP QMP PHY device node with the OF ports required to
>>> support USB-C / DisplayPort switching.
>>>
>>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
>>> ---
>>>  arch/arm64/boot/dts/qcom/sm8150.dtsi | 23 +++++++++++++++++++++++
>>>  1 file changed, 23 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
>>> index ea7c92c0e405..38423a9f8408 100644
>>> --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
>>> +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
>>> @@ -3447,6 +3447,29 @@ usb_1_qmpphy: phy@88e8000 {
>>>                       #phy-cells = <1>;
>>>
>>>                       status = "disabled";
>>> +
>>> +                     ports {
>>> +                             #address-cells = <1>;
>>> +                             #size-cells = <0>;
>>> +
>>> +                             port@0 {
>>> +                                     reg = <0>;
>>> +                                     usb_1_qmpphy_out: endpoint {};
>> style 1
>>> +                             };
>>> +
>>> +                             port@1 {
>>> +                                     reg = <1>;
>>> +
>>> +                                     usb_1_qmpphy_usb_ss_in: endpoint {
>>> +                                     };
>> style 2
>>> +                             };
>>> +
>>> +                             port@2 {
>>> +                                     reg = <2>;
>>> +
>>> +                                     usb_1_qmpphy_dp_in: endpoint {};
>> style 3
>>
>> :(
> 
> Which one should I stick to?
style 2 seems to be used in 8650

Konrad

Re: [PATCH 7/9] arm64: dts: qcom: sm8150: add USB-C ports to the USB+DP QMP PHY

[Konrad Dybcio]

On 11.12.2023 10:46, Dmitry Baryshkov wrote:
> On Mon, 11 Dec 2023 at 11:33, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>>
>> On 10.12.2023 00:21, Dmitry Baryshkov wrote:
>>> Expand Combo USB+DP QMP PHY device node with the OF ports required to
>>> support USB-C / DisplayPort switching.
>>>
>>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
>>> ---
>>>  arch/arm64/boot/dts/qcom/sm8150.dtsi | 23 +++++++++++++++++++++++
>>>  1 file changed, 23 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
>>> index ea7c92c0e405..38423a9f8408 100644
>>> --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
>>> +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
>>> @@ -3447,6 +3447,29 @@ usb_1_qmpphy: phy@88e8000 {
>>>                       #phy-cells = <1>;
>>>
>>>                       status = "disabled";
>>> +
>>> +                     ports {
>>> +                             #address-cells = <1>;
>>> +                             #size-cells = <0>;
>>> +
>>> +                             port@0 {
>>> +                                     reg = <0>;
>>> +                                     usb_1_qmpphy_out: endpoint {};
>> style 1
>>> +                             };
>>> +
>>> +                             port@1 {
>>> +                                     reg = <1>;
>>> +
>>> +                                     usb_1_qmpphy_usb_ss_in: endpoint {
>>> +                                     };
>> style 2
>>> +                             };
>>> +
>>> +                             port@2 {
>>> +                                     reg = <2>;
>>> +
>>> +                                     usb_1_qmpphy_dp_in: endpoint {};
>> style 3
>>
>> :(
> 
> Which one should I stick to?
style 2 seems to be used in 8650

Konrad

Re: [PATCH 1/9] dt-bindings: display: msm: dp: declare compatible string for sm8150

[Krzysztof Kozlowski]

On 10/12/2023 00:21, Dmitry Baryshkov wrote:
> Add compatible string for the DisplayPort controller found on the
> Qualcomm SM8150 platform.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH 1/9] dt-bindings: display: msm: dp: declare compatible string for sm8150

[Krzysztof Kozlowski]

On 10/12/2023 00:21, Dmitry Baryshkov wrote:
> Add compatible string for the DisplayPort controller found on the
> Qualcomm SM8150 platform.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH 1/9] dt-bindings: display: msm: dp: declare compatible string for sm8150

[Krzysztof Kozlowski]

On 10/12/2023 00:21, Dmitry Baryshkov wrote:
> Add compatible string for the DisplayPort controller found on the
> Qualcomm SM8150 platform.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---


Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH 1/9] dt-bindings: display: msm: dp: declare compatible string for sm8150

[Krzysztof Kozlowski]

On 10/12/2023 00:21, Dmitry Baryshkov wrote:
> Add compatible string for the DisplayPort controller found on the
> Qualcomm SM8150 platform.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---


Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH 0/9] arm64: dts: qcom: sm8150-hdk: enable display output

[Dmitry Baryshkov]

On Sun, 10 Dec 2023 02:21:23 +0300, Dmitry Baryshkov wrote:
> Enable display output on the SM8150 HDK device. This includes HDMI
> output through the onboard DSI-HDMI bridge and DP output on the USB-C
> port.
> 
> Dmitry Baryshkov (9):
>   dt-bindings: display: msm: dp: declare compatible string for sm8150
>   arm64: dts: qcom: sm8150: use SoC-specific compat for RPMh stats
>   arm64: dts: qcom: sm8150: make dispcc cast minimal vote on MMCX
>   arm64: dts: qcom: sm8150-hdk: enable HDMI output
>   arm64: dts: qcom: sm8150-hdk: fix SS USB regulators
>   arm64: dts: qcom: sm8150: add DisplayPort controller
>   arm64: dts: qcom: sm8150: add USB-C ports to the USB+DP QMP PHY
>   arm64: dts: qcom: sm8150: add USB-C ports to the OTG USB host
>   arm64: dts: qcom: sm8150-hdk: enable DisplayPort and USB-C altmode
> 
> [...]

Applied, thanks!

[1/9] dt-bindings: display: msm: dp: declare compatible string for sm8150
      https://gitlab.freedesktop.org/lumag/msm/-/commit/0d196633771c

Best regards,
-- 
Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

Re: [PATCH 0/9] arm64: dts: qcom: sm8150-hdk: enable display output

[Dmitry Baryshkov]

On Sun, 10 Dec 2023 02:21:23 +0300, Dmitry Baryshkov wrote:
> Enable display output on the SM8150 HDK device. This includes HDMI
> output through the onboard DSI-HDMI bridge and DP output on the USB-C
> port.
> 
> Dmitry Baryshkov (9):
>   dt-bindings: display: msm: dp: declare compatible string for sm8150
>   arm64: dts: qcom: sm8150: use SoC-specific compat for RPMh stats
>   arm64: dts: qcom: sm8150: make dispcc cast minimal vote on MMCX
>   arm64: dts: qcom: sm8150-hdk: enable HDMI output
>   arm64: dts: qcom: sm8150-hdk: fix SS USB regulators
>   arm64: dts: qcom: sm8150: add DisplayPort controller
>   arm64: dts: qcom: sm8150: add USB-C ports to the USB+DP QMP PHY
>   arm64: dts: qcom: sm8150: add USB-C ports to the OTG USB host
>   arm64: dts: qcom: sm8150-hdk: enable DisplayPort and USB-C altmode
> 
> [...]

Applied, thanks!

[1/9] dt-bindings: display: msm: dp: declare compatible string for sm8150
      https://gitlab.freedesktop.org/lumag/msm/-/commit/0d196633771c

Best regards,
-- 
Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

Re: [PATCH 7/9] arm64: dts: qcom: sm8150: add USB-C ports to the USB+DP QMP PHY

[neil.armstrong]

On 11/12/2023 10:50, Konrad Dybcio wrote:
> On 11.12.2023 10:46, Dmitry Baryshkov wrote:
>> On Mon, 11 Dec 2023 at 11:33, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>>>
>>> On 10.12.2023 00:21, Dmitry Baryshkov wrote:
>>>> Expand Combo USB+DP QMP PHY device node with the OF ports required to
>>>> support USB-C / DisplayPort switching.
>>>>
>>>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
>>>> ---
>>>>   arch/arm64/boot/dts/qcom/sm8150.dtsi | 23 +++++++++++++++++++++++
>>>>   1 file changed, 23 insertions(+)
>>>>
>>>> diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
>>>> index ea7c92c0e405..38423a9f8408 100644
>>>> --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
>>>> +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
>>>> @@ -3447,6 +3447,29 @@ usb_1_qmpphy: phy@88e8000 {
>>>>                        #phy-cells = <1>;
>>>>
>>>>                        status = "disabled";
>>>> +
>>>> +                     ports {
>>>> +                             #address-cells = <1>;
>>>> +                             #size-cells = <0>;
>>>> +
>>>> +                             port@0 {
>>>> +                                     reg = <0>;
>>>> +                                     usb_1_qmpphy_out: endpoint {};
>>> style 1
>>>> +                             };
>>>> +
>>>> +                             port@1 {
>>>> +                                     reg = <1>;
>>>> +
>>>> +                                     usb_1_qmpphy_usb_ss_in: endpoint {
>>>> +                                     };
>>> style 2
>>>> +                             };
>>>> +
>>>> +                             port@2 {
>>>> +                                     reg = <2>;
>>>> +
>>>> +                                     usb_1_qmpphy_dp_in: endpoint {};
>>> style 3
>>>
>>> :(
>>
>> Which one should I stick to?
> style 2 seems to be used in 8650

I used style 2 for 8450/8550/8650 usb & dp ports, but the 3 styles are present in the qcom dts.

Neil

> 
> Konrad
> 

Re: [PATCH 7/9] arm64: dts: qcom: sm8150: add USB-C ports to the USB+DP QMP PHY

[neil.armstrong]

On 11/12/2023 10:50, Konrad Dybcio wrote:
> On 11.12.2023 10:46, Dmitry Baryshkov wrote:
>> On Mon, 11 Dec 2023 at 11:33, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>>>
>>> On 10.12.2023 00:21, Dmitry Baryshkov wrote:
>>>> Expand Combo USB+DP QMP PHY device node with the OF ports required to
>>>> support USB-C / DisplayPort switching.
>>>>
>>>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
>>>> ---
>>>>   arch/arm64/boot/dts/qcom/sm8150.dtsi | 23 +++++++++++++++++++++++
>>>>   1 file changed, 23 insertions(+)
>>>>
>>>> diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
>>>> index ea7c92c0e405..38423a9f8408 100644
>>>> --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
>>>> +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
>>>> @@ -3447,6 +3447,29 @@ usb_1_qmpphy: phy@88e8000 {
>>>>                        #phy-cells = <1>;
>>>>
>>>>                        status = "disabled";
>>>> +
>>>> +                     ports {
>>>> +                             #address-cells = <1>;
>>>> +                             #size-cells = <0>;
>>>> +
>>>> +                             port@0 {
>>>> +                                     reg = <0>;
>>>> +                                     usb_1_qmpphy_out: endpoint {};
>>> style 1
>>>> +                             };
>>>> +
>>>> +                             port@1 {
>>>> +                                     reg = <1>;
>>>> +
>>>> +                                     usb_1_qmpphy_usb_ss_in: endpoint {
>>>> +                                     };
>>> style 2
>>>> +                             };
>>>> +
>>>> +                             port@2 {
>>>> +                                     reg = <2>;
>>>> +
>>>> +                                     usb_1_qmpphy_dp_in: endpoint {};
>>> style 3
>>>
>>> :(
>>
>> Which one should I stick to?
> style 2 seems to be used in 8650

I used style 2 for 8450/8550/8650 usb & dp ports, but the 3 styles are present in the qcom dts.

Neil

> 
> Konrad
>