* [GIT PULL] Renesas ARM64 Based SoC DT Updates for v4.10
@ 2016-11-04 9:44 ` Simon Horman
0 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
Hi Olof, Hi Kevin, Hi Arnd,
Please consider these Renesas ARM64 based SoC DT updates for v4.10.
The following changes since commit 1001354ca34179f3db924eb66672442a173147dc:
Linux 4.9-rc1 (2016-10-15 12:17:50 -0700)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-arm64-dt-for-v4.10
for you to fetch changes up to 935085209343a0c507e3d9a3e01883b25c8f743e:
arm64: renesas: r8a7796: add SYS-DMAC controller nodes (2016-11-04 10:18:07 +0100)
----------------------------------------------------------------
Renesas ARM64 Based SoC DT Updates for v4.10
Enablement:
* Enable On-board eMMC
* Enable SDHI 0 & 3 with UHS
* Add SYS-DMAC controller nodes to r8a7796 SoC
* Populate EXTALR on r8a7796/salvator-x board; used by watchdog
* Add DU LVDS output endpoint on r8a7795/salvator-x board
* Add bias setting for USB1 pins on r8a7795/salvator-x board
Clean-Up:
* Remove FCP SoC-specific compatible strings
----------------------------------------------------------------
Geert Uytterhoeven (1):
arm64: dts: r8a7796: salvator-x: Populate EXTALR
Laurent Pinchart (3):
arm64: dts: r8a7795: salvator-x: Add DU LVDS output endpoint
dt-bindings: media: renesas-fcp: Remove SoC-specific compatible strings
arm64: dts: r8a7795: Remove FCP SoC-specific compatible strings
Simon Horman (3):
arm64: dts: r8a7796: add SDHI nodes
arm64: dts: r8a7796: salvator-x: enable SDHI0 & 3
arm64: dts: r8a7796: salvator-x: enable UHS for SDHI 0 & 3
Ulrich Hecht (1):
arm64: renesas: r8a7796: add SYS-DMAC controller nodes
Wolfram Sang (3):
arm64: dts: r8a7795: salvator-x: enable UHS for SDHI 0 & 3
arm64: dts: r8a7795: salvator: enable on-board eMMC
arm64: dts: r8a7796: salvator: enable on board eMMC
Yoshihiro Shimoda (1):
arm64: dts: r8a7795: salvator-x: add bias setting for usb1_pins
.../devicetree/bindings/media/renesas,fcp.txt | 8 +-
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 85 +++++++++++-
arch/arm64/boot/dts/renesas/r8a7795.dtsi | 24 ++--
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 148 +++++++++++++++++++++
arch/arm64/boot/dts/renesas/r8a7796.dtsi | 139 +++++++++++++++++++
5 files changed, 381 insertions(+), 23 deletions(-)
^ permalink raw reply [flat|nested] 28+ messages in thread* [PATCH 01/12] arm64: dts: r8a7795: salvator-x: enable UHS for SDHI 0 & 3
2016-11-04 9:44 ` Simon Horman
@ 2016-11-04 9:43 ` Simon Horman
-1 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
From: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 22 ++++++++++++++++++++--
1 file changed, 20 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index b1eab6876f8c..ff4e4fe843ed 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -237,11 +237,25 @@
sdhi0_pins: sd0 {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
+ power-source = <3300>;
+ };
+
+ sdhi0_pins_uhs: sd0_uhs {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ power-source = <1800>;
};
sdhi3_pins: sd3 {
groups = "sdhi3_data4", "sdhi3_ctrl";
function = "sdhi3";
+ power-source = <3300>;
+ };
+
+ sdhi3_pins_uhs: sd3_uhs {
+ groups = "sdhi3_data4", "sdhi3_ctrl";
+ function = "sdhi3";
+ power-source = <1800>;
};
sound_pins: sound {
@@ -371,25 +385,29 @@
&sdhi0 {
pinctrl-0 = <&sdhi0_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdhi0_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi0>;
vqmmc-supply = <&vccq_sdhi0>;
cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
bus-width = <4>;
+ sd-uhs-sdr50;
status = "okay";
};
&sdhi3 {
pinctrl-0 = <&sdhi3_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdhi3_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi3>;
vqmmc-supply = <&vccq_sdhi3>;
cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
bus-width = <4>;
+ sd-uhs-sdr50;
status = "okay";
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread* [PATCH 01/12] arm64: dts: r8a7795: salvator-x: enable UHS for SDHI 0 & 3
@ 2016-11-04 9:43 ` Simon Horman
0 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:43 UTC (permalink / raw)
To: linux-arm-kernel
From: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 22 ++++++++++++++++++++--
1 file changed, 20 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index b1eab6876f8c..ff4e4fe843ed 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -237,11 +237,25 @@
sdhi0_pins: sd0 {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
+ power-source = <3300>;
+ };
+
+ sdhi0_pins_uhs: sd0_uhs {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ power-source = <1800>;
};
sdhi3_pins: sd3 {
groups = "sdhi3_data4", "sdhi3_ctrl";
function = "sdhi3";
+ power-source = <3300>;
+ };
+
+ sdhi3_pins_uhs: sd3_uhs {
+ groups = "sdhi3_data4", "sdhi3_ctrl";
+ function = "sdhi3";
+ power-source = <1800>;
};
sound_pins: sound {
@@ -371,25 +385,29 @@
&sdhi0 {
pinctrl-0 = <&sdhi0_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdhi0_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi0>;
vqmmc-supply = <&vccq_sdhi0>;
cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
bus-width = <4>;
+ sd-uhs-sdr50;
status = "okay";
};
&sdhi3 {
pinctrl-0 = <&sdhi3_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdhi3_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi3>;
vqmmc-supply = <&vccq_sdhi3>;
cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
bus-width = <4>;
+ sd-uhs-sdr50;
status = "okay";
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH 02/12] arm64: dts: r8a7796: salvator-x: Populate EXTALR
2016-11-04 9:44 ` Simon Horman
@ 2016-11-04 9:43 ` Simon Horman
-1 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Geert Uytterhoeven, Simon Horman
From: Geert Uytterhoeven <geert+renesas@glider.be>
It can be used for the watchdog.
Based on similar work for r8a7795/salvator-x by Wolfram Sang.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index 13db7d61c26c..90e9a76c8b30 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -49,6 +49,10 @@
clock-frequency = <16666666>;
};
+&extalr_clk {
+ clock-frequency = <32768>;
+};
+
&scif2 {
pinctrl-0 = <&scif2_pins>;
pinctrl-names = "default";
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread* [PATCH 02/12] arm64: dts: r8a7796: salvator-x: Populate EXTALR
@ 2016-11-04 9:43 ` Simon Horman
0 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:43 UTC (permalink / raw)
To: linux-arm-kernel
From: Geert Uytterhoeven <geert+renesas@glider.be>
It can be used for the watchdog.
Based on similar work for r8a7795/salvator-x by Wolfram Sang.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index 13db7d61c26c..90e9a76c8b30 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -49,6 +49,10 @@
clock-frequency = <16666666>;
};
+&extalr_clk {
+ clock-frequency = <32768>;
+};
+
&scif2 {
pinctrl-0 = <&scif2_pins>;
pinctrl-names = "default";
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH 03/12] arm64: dts: r8a7795: salvator-x: Add DU LVDS output endpoint
2016-11-04 9:44 ` Simon Horman
@ 2016-11-04 9:43 ` Simon Horman
-1 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Laurent Pinchart, Simon Horman
From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Declaring the endpoint makes LVDS enablement easier by just including
the corresponding panel's dtsi file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index ff4e4fe843ed..c8f6023c4667 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -191,6 +191,10 @@
remote-endpoint = <&adv7123_in>;
};
};
+ port@3 {
+ lvds_connector: endpoint {
+ };
+ };
};
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread* [PATCH 03/12] arm64: dts: r8a7795: salvator-x: Add DU LVDS output endpoint
@ 2016-11-04 9:43 ` Simon Horman
0 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:43 UTC (permalink / raw)
To: linux-arm-kernel
From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Declaring the endpoint makes LVDS enablement easier by just including
the corresponding panel's dtsi file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index ff4e4fe843ed..c8f6023c4667 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -191,6 +191,10 @@
remote-endpoint = <&adv7123_in>;
};
};
+ port at 3 {
+ lvds_connector: endpoint {
+ };
+ };
};
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH 04/12] dt-bindings: media: renesas-fcp: Remove SoC-specific compatible strings
2016-11-04 9:44 ` Simon Horman
@ 2016-11-04 9:43 ` Simon Horman
-1 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Laurent Pinchart, Simon Horman
From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The FCP IP cores include a version register that identifies which SoC
model the IP is integrated in. SoC-specific compatible strings are not
needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
Documentation/devicetree/bindings/media/renesas,fcp.txt | 8 +-------
1 file changed, 1 insertion(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/media/renesas,fcp.txt b/Documentation/devicetree/bindings/media/renesas,fcp.txt
index 27f9b8e459ac..3ec91803ba58 100644
--- a/Documentation/devicetree/bindings/media/renesas,fcp.txt
+++ b/Documentation/devicetree/bindings/media/renesas,fcp.txt
@@ -11,15 +11,9 @@ are paired with. These DT bindings currently support the FCPV and FCPF.
- compatible: Must be one or more of the following
- - "renesas,r8a7795-fcpv" for R8A7795 (R-Car H3) compatible 'FCP for VSP'
- - "renesas,r8a7795-fcpf" for R8A7795 (R-Car H3) compatible 'FCP for FDP'
- "renesas,fcpv" for generic compatible 'FCP for VSP'
- "renesas,fcpf" for generic compatible 'FCP for FDP'
- When compatible with the generic version, nodes must list the
- SoC-specific version corresponding to the platform first, followed by the
- family-specific and/or generic versions.
-
- reg: the register base and size for the device registers
- clocks: Reference to the functional clock
@@ -32,7 +26,7 @@ Device node example
-------------------
fcpvd1: fcp@fea2f000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfea2f000 0 0x200>;
clocks = <&cpg CPG_MOD 602>;
power-domains = <&sysc R8A7795_PD_A3VP>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread* [PATCH 04/12] dt-bindings: media: renesas-fcp: Remove SoC-specific compatible strings
@ 2016-11-04 9:43 ` Simon Horman
0 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:43 UTC (permalink / raw)
To: linux-arm-kernel
From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The FCP IP cores include a version register that identifies which SoC
model the IP is integrated in. SoC-specific compatible strings are not
needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
Documentation/devicetree/bindings/media/renesas,fcp.txt | 8 +-------
1 file changed, 1 insertion(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/media/renesas,fcp.txt b/Documentation/devicetree/bindings/media/renesas,fcp.txt
index 27f9b8e459ac..3ec91803ba58 100644
--- a/Documentation/devicetree/bindings/media/renesas,fcp.txt
+++ b/Documentation/devicetree/bindings/media/renesas,fcp.txt
@@ -11,15 +11,9 @@ are paired with. These DT bindings currently support the FCPV and FCPF.
- compatible: Must be one or more of the following
- - "renesas,r8a7795-fcpv" for R8A7795 (R-Car H3) compatible 'FCP for VSP'
- - "renesas,r8a7795-fcpf" for R8A7795 (R-Car H3) compatible 'FCP for FDP'
- "renesas,fcpv" for generic compatible 'FCP for VSP'
- "renesas,fcpf" for generic compatible 'FCP for FDP'
- When compatible with the generic version, nodes must list the
- SoC-specific version corresponding to the platform first, followed by the
- family-specific and/or generic versions.
-
- reg: the register base and size for the device registers
- clocks: Reference to the functional clock
@@ -32,7 +26,7 @@ Device node example
-------------------
fcpvd1: fcp at fea2f000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfea2f000 0 0x200>;
clocks = <&cpg CPG_MOD 602>;
power-domains = <&sysc R8A7795_PD_A3VP>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH 05/12] arm64: dts: r8a7795: Remove FCP SoC-specific compatible strings
2016-11-04 9:44 ` Simon Horman
@ 2016-11-04 9:44 ` Simon Horman
-1 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Laurent Pinchart, Simon Horman
From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The SoC-specific compatible strings have been removed from the FCP DT
bindings, removed them from the device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795.dtsi | 24 ++++++++++++------------
1 file changed, 12 insertions(+), 12 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
index 8c15040f2540..681f54422375 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -1306,28 +1306,28 @@
};
fcpvb1: fcp@fe92f000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfe92f000 0 0x200>;
clocks = <&cpg CPG_MOD 606>;
power-domains = <&sysc R8A7795_PD_A3VP>;
};
fcpf0: fcp@fe950000 {
- compatible = "renesas,r8a7795-fcpf", "renesas,fcpf";
+ compatible = "renesas,fcpf";
reg = <0 0xfe950000 0 0x200>;
clocks = <&cpg CPG_MOD 615>;
power-domains = <&sysc R8A7795_PD_A3VP>;
};
fcpf1: fcp@fe951000 {
- compatible = "renesas,r8a7795-fcpf", "renesas,fcpf";
+ compatible = "renesas,fcpf";
reg = <0 0xfe951000 0 0x200>;
clocks = <&cpg CPG_MOD 614>;
power-domains = <&sysc R8A7795_PD_A3VP>;
};
fcpf2: fcp@fe952000 {
- compatible = "renesas,r8a7795-fcpf", "renesas,fcpf";
+ compatible = "renesas,fcpf";
reg = <0 0xfe952000 0 0x200>;
clocks = <&cpg CPG_MOD 613>;
power-domains = <&sysc R8A7795_PD_A3VP>;
@@ -1344,7 +1344,7 @@
};
fcpvb0: fcp@fe96f000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfe96f000 0 0x200>;
clocks = <&cpg CPG_MOD 607>;
power-domains = <&sysc R8A7795_PD_A3VP>;
@@ -1361,7 +1361,7 @@
};
fcpvi0: fcp@fe9af000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfe9af000 0 0x200>;
clocks = <&cpg CPG_MOD 611>;
power-domains = <&sysc R8A7795_PD_A3VP>;
@@ -1378,7 +1378,7 @@
};
fcpvi1: fcp@fe9bf000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfe9bf000 0 0x200>;
clocks = <&cpg CPG_MOD 610>;
power-domains = <&sysc R8A7795_PD_A3VP>;
@@ -1395,7 +1395,7 @@
};
fcpvi2: fcp@fe9cf000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfe9cf000 0 0x200>;
clocks = <&cpg CPG_MOD 609>;
power-domains = <&sysc R8A7795_PD_A3VP>;
@@ -1412,7 +1412,7 @@
};
fcpvd0: fcp@fea27000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfea27000 0 0x200>;
clocks = <&cpg CPG_MOD 603>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
@@ -1429,7 +1429,7 @@
};
fcpvd1: fcp@fea2f000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfea2f000 0 0x200>;
clocks = <&cpg CPG_MOD 602>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
@@ -1446,7 +1446,7 @@
};
fcpvd2: fcp@fea37000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfea37000 0 0x200>;
clocks = <&cpg CPG_MOD 601>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
@@ -1463,7 +1463,7 @@
};
fcpvd3: fcp@fea3f000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfea3f000 0 0x200>;
clocks = <&cpg CPG_MOD 600>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread* [PATCH 05/12] arm64: dts: r8a7795: Remove FCP SoC-specific compatible strings
@ 2016-11-04 9:44 ` Simon Horman
0 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The SoC-specific compatible strings have been removed from the FCP DT
bindings, removed them from the device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795.dtsi | 24 ++++++++++++------------
1 file changed, 12 insertions(+), 12 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
index 8c15040f2540..681f54422375 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -1306,28 +1306,28 @@
};
fcpvb1: fcp at fe92f000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfe92f000 0 0x200>;
clocks = <&cpg CPG_MOD 606>;
power-domains = <&sysc R8A7795_PD_A3VP>;
};
fcpf0: fcp at fe950000 {
- compatible = "renesas,r8a7795-fcpf", "renesas,fcpf";
+ compatible = "renesas,fcpf";
reg = <0 0xfe950000 0 0x200>;
clocks = <&cpg CPG_MOD 615>;
power-domains = <&sysc R8A7795_PD_A3VP>;
};
fcpf1: fcp at fe951000 {
- compatible = "renesas,r8a7795-fcpf", "renesas,fcpf";
+ compatible = "renesas,fcpf";
reg = <0 0xfe951000 0 0x200>;
clocks = <&cpg CPG_MOD 614>;
power-domains = <&sysc R8A7795_PD_A3VP>;
};
fcpf2: fcp at fe952000 {
- compatible = "renesas,r8a7795-fcpf", "renesas,fcpf";
+ compatible = "renesas,fcpf";
reg = <0 0xfe952000 0 0x200>;
clocks = <&cpg CPG_MOD 613>;
power-domains = <&sysc R8A7795_PD_A3VP>;
@@ -1344,7 +1344,7 @@
};
fcpvb0: fcp at fe96f000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfe96f000 0 0x200>;
clocks = <&cpg CPG_MOD 607>;
power-domains = <&sysc R8A7795_PD_A3VP>;
@@ -1361,7 +1361,7 @@
};
fcpvi0: fcp at fe9af000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfe9af000 0 0x200>;
clocks = <&cpg CPG_MOD 611>;
power-domains = <&sysc R8A7795_PD_A3VP>;
@@ -1378,7 +1378,7 @@
};
fcpvi1: fcp at fe9bf000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfe9bf000 0 0x200>;
clocks = <&cpg CPG_MOD 610>;
power-domains = <&sysc R8A7795_PD_A3VP>;
@@ -1395,7 +1395,7 @@
};
fcpvi2: fcp at fe9cf000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfe9cf000 0 0x200>;
clocks = <&cpg CPG_MOD 609>;
power-domains = <&sysc R8A7795_PD_A3VP>;
@@ -1412,7 +1412,7 @@
};
fcpvd0: fcp at fea27000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfea27000 0 0x200>;
clocks = <&cpg CPG_MOD 603>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
@@ -1429,7 +1429,7 @@
};
fcpvd1: fcp at fea2f000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfea2f000 0 0x200>;
clocks = <&cpg CPG_MOD 602>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
@@ -1446,7 +1446,7 @@
};
fcpvd2: fcp at fea37000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfea37000 0 0x200>;
clocks = <&cpg CPG_MOD 601>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
@@ -1463,7 +1463,7 @@
};
fcpvd3: fcp at fea3f000 {
- compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ compatible = "renesas,fcpv";
reg = <0 0xfea3f000 0 0x200>;
clocks = <&cpg CPG_MOD 600>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH 06/12] arm64: dts: r8a7796: add SDHI nodes
2016-11-04 9:44 ` Simon Horman
@ 2016-11-04 9:44 ` Simon Horman
-1 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-renesas-soc; +Cc: linux-arm-kernel, Magnus Damm, Simon Horman
Add SDHI nodes to the DT of the r8a7796 SoC.
Based on the DT of the r8a7795 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm64/boot/dts/renesas/r8a7796.dtsi | 40 ++++++++++++++++++++++++++++++++
1 file changed, 40 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 9217da983525..6ec988c78ff8 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -251,5 +251,45 @@
power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
status = "disabled";
};
+
+ sdhi0: sd@ee100000 {
+ compatible = "renesas,sdhi-r8a7796";
+ reg = <0 0xee100000 0 0x2000>;
+ interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 314>;
+ max-frequency = <200000000>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+
+ sdhi1: sd@ee120000 {
+ compatible = "renesas,sdhi-r8a7796";
+ reg = <0 0xee120000 0 0x2000>;
+ interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 313>;
+ max-frequency = <200000000>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+
+ sdhi2: sd@ee140000 {
+ compatible = "renesas,sdhi-r8a7796";
+ reg = <0 0xee140000 0 0x2000>;
+ interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 312>;
+ max-frequency = <200000000>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+
+ sdhi3: sd@ee160000 {
+ compatible = "renesas,sdhi-r8a7796";
+ reg = <0 0xee160000 0 0x2000>;
+ interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 311>;
+ max-frequency = <200000000>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
};
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread* [PATCH 06/12] arm64: dts: r8a7796: add SDHI nodes
@ 2016-11-04 9:44 ` Simon Horman
0 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
Add SDHI nodes to the DT of the r8a7796 SoC.
Based on the DT of the r8a7795 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm64/boot/dts/renesas/r8a7796.dtsi | 40 ++++++++++++++++++++++++++++++++
1 file changed, 40 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 9217da983525..6ec988c78ff8 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -251,5 +251,45 @@
power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
status = "disabled";
};
+
+ sdhi0: sd at ee100000 {
+ compatible = "renesas,sdhi-r8a7796";
+ reg = <0 0xee100000 0 0x2000>;
+ interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 314>;
+ max-frequency = <200000000>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+
+ sdhi1: sd at ee120000 {
+ compatible = "renesas,sdhi-r8a7796";
+ reg = <0 0xee120000 0 0x2000>;
+ interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 313>;
+ max-frequency = <200000000>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+
+ sdhi2: sd at ee140000 {
+ compatible = "renesas,sdhi-r8a7796";
+ reg = <0 0xee140000 0 0x2000>;
+ interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 312>;
+ max-frequency = <200000000>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+
+ sdhi3: sd at ee160000 {
+ compatible = "renesas,sdhi-r8a7796";
+ reg = <0 0xee160000 0 0x2000>;
+ interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 311>;
+ max-frequency = <200000000>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
};
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH 07/12] arm64: dts: r8a7796: salvator-x: enable SDHI0 & 3
2016-11-04 9:44 ` Simon Horman
@ 2016-11-04 9:44 ` Simon Horman
-1 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-renesas-soc; +Cc: linux-arm-kernel, Magnus Damm, Simon Horman
Enable the exposed SD card slots in the DT of the r8a7796/salvator-x.
Based on work for the r8a7795/salvator-x by Ai Kyuse.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 84 ++++++++++++++++++++++
1 file changed, 84 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index 90e9a76c8b30..c946569accb1 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -10,6 +10,7 @@
/dts-v1/;
#include "r8a7796.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "Renesas Salvator-X board based on r8a7796";
@@ -29,6 +30,55 @@
/* first 128MB is reserved for secure area. */
reg = <0x0 0x48000000 0x0 0x78000000>;
};
+
+ vcc_sdhi0: regulator-vcc-sdhi0 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDHI0 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vccq_sdhi0: regulator-vccq-sdhi0 {
+ compatible = "regulator-gpio";
+
+ regulator-name = "SDHI0 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1
+ 1800000 0>;
+ };
+
+ vcc_sdhi3: regulator-vcc-sdhi3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDHI3 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vccq_sdhi3: regulator-vccq-sdhi3 {
+ compatible = "regulator-gpio";
+
+ regulator-name = "SDHI3 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1
+ 1800000 0>;
+ };
+
};
&pfc {
@@ -43,6 +93,16 @@
groups = "scif_clk_a";
function = "scif_clk";
};
+
+ sdhi0_pins: sd0 {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ };
+
+ sdhi3_pins: sd3 {
+ groups = "sdhi3_data4", "sdhi3_ctrl";
+ function = "sdhi3";
+ };
};
&extal_clk {
@@ -53,6 +113,30 @@
clock-frequency = <32768>;
};
+&sdhi0 {
+ pinctrl-0 = <&sdhi0_pins>;
+ pinctrl-names = "default";
+
+ vmmc-supply = <&vcc_sdhi0>;
+ vqmmc-supply = <&vccq_sdhi0>;
+ cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&sdhi3 {
+ pinctrl-0 = <&sdhi3_pins>;
+ pinctrl-names = "default";
+
+ vmmc-supply = <&vcc_sdhi3>;
+ vqmmc-supply = <&vccq_sdhi3>;
+ cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+ bus-width = <4>;
+ status = "okay";
+};
+
&scif2 {
pinctrl-0 = <&scif2_pins>;
pinctrl-names = "default";
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread* [PATCH 07/12] arm64: dts: r8a7796: salvator-x: enable SDHI0 & 3
@ 2016-11-04 9:44 ` Simon Horman
0 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
Enable the exposed SD card slots in the DT of the r8a7796/salvator-x.
Based on work for the r8a7795/salvator-x by Ai Kyuse.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 84 ++++++++++++++++++++++
1 file changed, 84 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index 90e9a76c8b30..c946569accb1 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -10,6 +10,7 @@
/dts-v1/;
#include "r8a7796.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "Renesas Salvator-X board based on r8a7796";
@@ -29,6 +30,55 @@
/* first 128MB is reserved for secure area. */
reg = <0x0 0x48000000 0x0 0x78000000>;
};
+
+ vcc_sdhi0: regulator-vcc-sdhi0 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDHI0 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vccq_sdhi0: regulator-vccq-sdhi0 {
+ compatible = "regulator-gpio";
+
+ regulator-name = "SDHI0 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1
+ 1800000 0>;
+ };
+
+ vcc_sdhi3: regulator-vcc-sdhi3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDHI3 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vccq_sdhi3: regulator-vccq-sdhi3 {
+ compatible = "regulator-gpio";
+
+ regulator-name = "SDHI3 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1
+ 1800000 0>;
+ };
+
};
&pfc {
@@ -43,6 +93,16 @@
groups = "scif_clk_a";
function = "scif_clk";
};
+
+ sdhi0_pins: sd0 {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ };
+
+ sdhi3_pins: sd3 {
+ groups = "sdhi3_data4", "sdhi3_ctrl";
+ function = "sdhi3";
+ };
};
&extal_clk {
@@ -53,6 +113,30 @@
clock-frequency = <32768>;
};
+&sdhi0 {
+ pinctrl-0 = <&sdhi0_pins>;
+ pinctrl-names = "default";
+
+ vmmc-supply = <&vcc_sdhi0>;
+ vqmmc-supply = <&vccq_sdhi0>;
+ cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&sdhi3 {
+ pinctrl-0 = <&sdhi3_pins>;
+ pinctrl-names = "default";
+
+ vmmc-supply = <&vcc_sdhi3>;
+ vqmmc-supply = <&vccq_sdhi3>;
+ cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+ bus-width = <4>;
+ status = "okay";
+};
+
&scif2 {
pinctrl-0 = <&scif2_pins>;
pinctrl-names = "default";
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH 08/12] arm64: dts: r8a7796: salvator-x: enable UHS for SDHI 0 & 3
2016-11-04 9:44 ` Simon Horman
@ 2016-11-04 9:44 ` Simon Horman
-1 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-renesas-soc; +Cc: linux-arm-kernel, Magnus Damm, Simon Horman
Based on work for the r8a7796 by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
---
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 22 ++++++++++++++++++++--
1 file changed, 20 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index c946569accb1..08c335afd970 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -97,11 +97,25 @@
sdhi0_pins: sd0 {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
+ power-source = <3300>;
+ };
+
+ sdhi0_pins_uhs: sd0_uhs {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ power-source = <1800>;
};
sdhi3_pins: sd3 {
groups = "sdhi3_data4", "sdhi3_ctrl";
function = "sdhi3";
+ power-source = <3300>;
+ };
+
+ sdhi3_pins_uhs: sd3_uhs {
+ groups = "sdhi3_data4", "sdhi3_ctrl";
+ function = "sdhi3";
+ power-source = <1800>;
};
};
@@ -115,25 +129,29 @@
&sdhi0 {
pinctrl-0 = <&sdhi0_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdhi0_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi0>;
vqmmc-supply = <&vccq_sdhi0>;
cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
bus-width = <4>;
+ sd-uhs-sdr50;
status = "okay";
};
&sdhi3 {
pinctrl-0 = <&sdhi3_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdhi3_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi3>;
vqmmc-supply = <&vccq_sdhi3>;
cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
bus-width = <4>;
+ sd-uhs-sdr50;
status = "okay";
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread* [PATCH 08/12] arm64: dts: r8a7796: salvator-x: enable UHS for SDHI 0 & 3
@ 2016-11-04 9:44 ` Simon Horman
0 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
Based on work for the r8a7796 by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
---
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 22 ++++++++++++++++++++--
1 file changed, 20 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index c946569accb1..08c335afd970 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -97,11 +97,25 @@
sdhi0_pins: sd0 {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
+ power-source = <3300>;
+ };
+
+ sdhi0_pins_uhs: sd0_uhs {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ power-source = <1800>;
};
sdhi3_pins: sd3 {
groups = "sdhi3_data4", "sdhi3_ctrl";
function = "sdhi3";
+ power-source = <3300>;
+ };
+
+ sdhi3_pins_uhs: sd3_uhs {
+ groups = "sdhi3_data4", "sdhi3_ctrl";
+ function = "sdhi3";
+ power-source = <1800>;
};
};
@@ -115,25 +129,29 @@
&sdhi0 {
pinctrl-0 = <&sdhi0_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdhi0_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi0>;
vqmmc-supply = <&vccq_sdhi0>;
cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
bus-width = <4>;
+ sd-uhs-sdr50;
status = "okay";
};
&sdhi3 {
pinctrl-0 = <&sdhi3_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdhi3_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi3>;
vqmmc-supply = <&vccq_sdhi3>;
cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
bus-width = <4>;
+ sd-uhs-sdr50;
status = "okay";
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH 09/12] arm64: dts: r8a7795: salvator: enable on-board eMMC
2016-11-04 9:44 ` Simon Horman
@ 2016-11-04 9:44 ` Simon Horman
-1 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
From: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 43 ++++++++++++++++++++++
1 file changed, 43 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index c8f6023c4667..da3e996ba121 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -62,6 +62,24 @@
clock-frequency = <24576000>;
};
+ reg_1p8v: regulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator1 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
@@ -250,6 +268,18 @@
power-source = <1800>;
};
+ sdhi2_pins: sd2 {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <3300>;
+ };
+
+ sdhi2_pins_uhs: sd2_uhs {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <1800>;
+ };
+
sdhi3_pins: sd3 {
groups = "sdhi3_data4", "sdhi3_ctrl";
function = "sdhi3";
@@ -401,6 +431,19 @@
status = "okay";
};
+&sdhi2 {
+ /* used for on-board 8bit eMMC */
+ pinctrl-0 = <&sdhi2_pins>;
+ pinctrl-1 = <&sdhi2_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
&sdhi3 {
pinctrl-0 = <&sdhi3_pins>;
pinctrl-1 = <&sdhi3_pins_uhs>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread* [PATCH 09/12] arm64: dts: r8a7795: salvator: enable on-board eMMC
@ 2016-11-04 9:44 ` Simon Horman
0 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
From: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 43 ++++++++++++++++++++++
1 file changed, 43 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index c8f6023c4667..da3e996ba121 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -62,6 +62,24 @@
clock-frequency = <24576000>;
};
+ reg_1p8v: regulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator1 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
@@ -250,6 +268,18 @@
power-source = <1800>;
};
+ sdhi2_pins: sd2 {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <3300>;
+ };
+
+ sdhi2_pins_uhs: sd2_uhs {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <1800>;
+ };
+
sdhi3_pins: sd3 {
groups = "sdhi3_data4", "sdhi3_ctrl";
function = "sdhi3";
@@ -401,6 +431,19 @@
status = "okay";
};
+&sdhi2 {
+ /* used for on-board 8bit eMMC */
+ pinctrl-0 = <&sdhi2_pins>;
+ pinctrl-1 = <&sdhi2_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
&sdhi3 {
pinctrl-0 = <&sdhi3_pins>;
pinctrl-1 = <&sdhi3_pins_uhs>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH 10/12] arm64: dts: r8a7796: salvator: enable on board eMMC
2016-11-04 9:44 ` Simon Horman
@ 2016-11-04 9:44 ` Simon Horman
-1 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
From: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 44 +++++++++++++++++++++-
1 file changed, 43 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index 08c335afd970..a9c296b1e1b7 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -31,6 +31,24 @@
reg = <0x0 0x48000000 0x0 0x78000000>;
};
+ reg_1p8v: regulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator1 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
@@ -78,7 +96,6 @@
states = <3300000 1
1800000 0>;
};
-
};
&pfc {
@@ -106,6 +123,18 @@
power-source = <1800>;
};
+ sdhi2_pins: sd2 {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <3300>;
+ };
+
+ sdhi2_pins_uhs: sd2_uhs {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <1800>;
+ };
+
sdhi3_pins: sd3 {
groups = "sdhi3_data4", "sdhi3_ctrl";
function = "sdhi3";
@@ -141,6 +170,19 @@
status = "okay";
};
+&sdhi2 {
+ /* used for on-board 8bit eMMC */
+ pinctrl-0 = <&sdhi2_pins>;
+ pinctrl-1 = <&sdhi2_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
&sdhi3 {
pinctrl-0 = <&sdhi3_pins>;
pinctrl-1 = <&sdhi3_pins_uhs>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread* [PATCH 10/12] arm64: dts: r8a7796: salvator: enable on board eMMC
@ 2016-11-04 9:44 ` Simon Horman
0 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
From: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 44 +++++++++++++++++++++-
1 file changed, 43 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index 08c335afd970..a9c296b1e1b7 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -31,6 +31,24 @@
reg = <0x0 0x48000000 0x0 0x78000000>;
};
+ reg_1p8v: regulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator1 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
@@ -78,7 +96,6 @@
states = <3300000 1
1800000 0>;
};
-
};
&pfc {
@@ -106,6 +123,18 @@
power-source = <1800>;
};
+ sdhi2_pins: sd2 {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <3300>;
+ };
+
+ sdhi2_pins_uhs: sd2_uhs {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <1800>;
+ };
+
sdhi3_pins: sd3 {
groups = "sdhi3_data4", "sdhi3_ctrl";
function = "sdhi3";
@@ -141,6 +170,19 @@
status = "okay";
};
+&sdhi2 {
+ /* used for on-board 8bit eMMC */
+ pinctrl-0 = <&sdhi2_pins>;
+ pinctrl-1 = <&sdhi2_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
&sdhi3 {
pinctrl-0 = <&sdhi3_pins>;
pinctrl-1 = <&sdhi3_pins_uhs>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH 11/12] arm64: dts: r8a7795: salvator-x: add bias setting for usb1_pins
2016-11-04 9:44 ` Simon Horman
@ 2016-11-04 9:44 ` Simon Horman
-1 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Yoshihiro Shimoda, Simon Horman
From: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Since this board doesn't mount pull-up/down registers for
USB1_{OVC,PWEN} pins, we should enable bias setting to pull these
pins up/down.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 16 ++++++++++++++--
1 file changed, 14 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index da3e996ba121..bcaf4008d32d 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -309,8 +309,20 @@
};
usb1_pins: usb1 {
- groups = "usb1";
- function = "usb1";
+ mux {
+ groups = "usb1";
+ function = "usb1";
+ };
+
+ ovc {
+ pins = "GP_6_27";
+ bias-pull-up;
+ };
+
+ pwen {
+ pins = "GP_6_26";
+ bias-pull-down;
+ };
};
usb2_pins: usb2 {
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread* [PATCH 11/12] arm64: dts: r8a7795: salvator-x: add bias setting for usb1_pins
@ 2016-11-04 9:44 ` Simon Horman
0 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
From: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Since this board doesn't mount pull-up/down registers for
USB1_{OVC,PWEN} pins, we should enable bias setting to pull these
pins up/down.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 16 ++++++++++++++--
1 file changed, 14 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index da3e996ba121..bcaf4008d32d 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -309,8 +309,20 @@
};
usb1_pins: usb1 {
- groups = "usb1";
- function = "usb1";
+ mux {
+ groups = "usb1";
+ function = "usb1";
+ };
+
+ ovc {
+ pins = "GP_6_27";
+ bias-pull-up;
+ };
+
+ pwen {
+ pins = "GP_6_26";
+ bias-pull-down;
+ };
};
usb2_pins: usb2 {
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH 12/12] arm64: renesas: r8a7796: add SYS-DMAC controller nodes
2016-11-04 9:44 ` Simon Horman
@ 2016-11-04 9:44 ` Simon Horman
-1 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Ulrich Hecht, Simon Horman
From: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796.dtsi | 99 ++++++++++++++++++++++++++++++++
1 file changed, 99 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 6ec988c78ff8..f9cb7796ad49 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -252,6 +252,105 @@
status = "disabled";
};
+ dmac0: dma-controller@e6700000 {
+ compatible = "renesas,dmac-r8a7796",
+ "renesas,rcar-dmac";
+ reg = <0 0xe6700000 0 0x10000>;
+ interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "error",
+ "ch0", "ch1", "ch2", "ch3",
+ "ch4", "ch5", "ch6", "ch7",
+ "ch8", "ch9", "ch10", "ch11",
+ "ch12", "ch13", "ch14", "ch15";
+ clocks = <&cpg CPG_MOD 219>;
+ clock-names = "fck";
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ #dma-cells = <1>;
+ dma-channels = <16>;
+ };
+
+ dmac1: dma-controller@e7300000 {
+ compatible = "renesas,dmac-r8a7796",
+ "renesas,rcar-dmac";
+ reg = <0 0xe7300000 0 0x10000>;
+ interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "error",
+ "ch0", "ch1", "ch2", "ch3",
+ "ch4", "ch5", "ch6", "ch7",
+ "ch8", "ch9", "ch10", "ch11",
+ "ch12", "ch13", "ch14", "ch15";
+ clocks = <&cpg CPG_MOD 218>;
+ clock-names = "fck";
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ #dma-cells = <1>;
+ dma-channels = <16>;
+ };
+
+ dmac2: dma-controller@e7310000 {
+ compatible = "renesas,dmac-r8a7796",
+ "renesas,rcar-dmac";
+ reg = <0 0xe7310000 0 0x10000>;
+ interrupts = <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 426 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 427 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 428 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 429 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 430 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 431 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "error",
+ "ch0", "ch1", "ch2", "ch3",
+ "ch4", "ch5", "ch6", "ch7",
+ "ch8", "ch9", "ch10", "ch11",
+ "ch12", "ch13", "ch14", "ch15";
+ clocks = <&cpg CPG_MOD 217>;
+ clock-names = "fck";
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ #dma-cells = <1>;
+ dma-channels = <16>;
+ };
+
sdhi0: sd@ee100000 {
compatible = "renesas,sdhi-r8a7796";
reg = <0 0xee100000 0 0x2000>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread* [PATCH 12/12] arm64: renesas: r8a7796: add SYS-DMAC controller nodes
@ 2016-11-04 9:44 ` Simon Horman
0 siblings, 0 replies; 28+ messages in thread
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
From: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796.dtsi | 99 ++++++++++++++++++++++++++++++++
1 file changed, 99 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 6ec988c78ff8..f9cb7796ad49 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -252,6 +252,105 @@
status = "disabled";
};
+ dmac0: dma-controller at e6700000 {
+ compatible = "renesas,dmac-r8a7796",
+ "renesas,rcar-dmac";
+ reg = <0 0xe6700000 0 0x10000>;
+ interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "error",
+ "ch0", "ch1", "ch2", "ch3",
+ "ch4", "ch5", "ch6", "ch7",
+ "ch8", "ch9", "ch10", "ch11",
+ "ch12", "ch13", "ch14", "ch15";
+ clocks = <&cpg CPG_MOD 219>;
+ clock-names = "fck";
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ #dma-cells = <1>;
+ dma-channels = <16>;
+ };
+
+ dmac1: dma-controller at e7300000 {
+ compatible = "renesas,dmac-r8a7796",
+ "renesas,rcar-dmac";
+ reg = <0 0xe7300000 0 0x10000>;
+ interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "error",
+ "ch0", "ch1", "ch2", "ch3",
+ "ch4", "ch5", "ch6", "ch7",
+ "ch8", "ch9", "ch10", "ch11",
+ "ch12", "ch13", "ch14", "ch15";
+ clocks = <&cpg CPG_MOD 218>;
+ clock-names = "fck";
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ #dma-cells = <1>;
+ dma-channels = <16>;
+ };
+
+ dmac2: dma-controller at e7310000 {
+ compatible = "renesas,dmac-r8a7796",
+ "renesas,rcar-dmac";
+ reg = <0 0xe7310000 0 0x10000>;
+ interrupts = <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 426 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 427 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 428 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 429 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 430 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 431 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "error",
+ "ch0", "ch1", "ch2", "ch3",
+ "ch4", "ch5", "ch6", "ch7",
+ "ch8", "ch9", "ch10", "ch11",
+ "ch12", "ch13", "ch14", "ch15";
+ clocks = <&cpg CPG_MOD 217>;
+ clock-names = "fck";
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ #dma-cells = <1>;
+ dma-channels = <16>;
+ };
+
sdhi0: sd at ee100000 {
compatible = "renesas,sdhi-r8a7796";
reg = <0 0xee100000 0 0x2000>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related [flat|nested] 28+ messages in thread
* Re: [GIT PULL] Renesas ARM64 Based SoC DT Updates for v4.10
2016-11-04 9:44 ` Simon Horman
@ 2016-11-18 1:40 ` Olof Johansson
-1 siblings, 0 replies; 28+ messages in thread
From: Olof Johansson @ 2016-11-18 1:40 UTC (permalink / raw)
To: Simon Horman
Cc: arm, linux-renesas-soc, Kevin Hilman, Arnd Bergmann,
linux-arm-kernel, Magnus Damm
On Fri, Nov 04, 2016 at 10:44:04AM +0100, Simon Horman wrote:
> Hi Olof, Hi Kevin, Hi Arnd,
>
> Please consider these Renesas ARM64 based SoC DT updates for v4.10.
>
>
> The following changes since commit 1001354ca34179f3db924eb66672442a173147dc:
>
> Linux 4.9-rc1 (2016-10-15 12:17:50 -0700)
>
> are available in the git repository at:
>
> git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-arm64-dt-for-v4.10
>
> for you to fetch changes up to 935085209343a0c507e3d9a3e01883b25c8f743e:
>
> arm64: renesas: r8a7796: add SYS-DMAC controller nodes (2016-11-04 10:18:07 +0100)
>
> ----------------------------------------------------------------
> Renesas ARM64 Based SoC DT Updates for v4.10
>
> Enablement:
> * Enable On-board eMMC
> * Enable SDHI 0 & 3 with UHS
> * Add SYS-DMAC controller nodes to r8a7796 SoC
> * Populate EXTALR on r8a7796/salvator-x board; used by watchdog
> * Add DU LVDS output endpoint on r8a7795/salvator-x board
> * Add bias setting for USB1 pins on r8a7795/salvator-x board
>
> Clean-Up:
> * Remove FCP SoC-specific compatible strings
Thanks, merged.
-Olof
^ permalink raw reply [flat|nested] 28+ messages in thread
* [GIT PULL] Renesas ARM64 Based SoC DT Updates for v4.10
@ 2016-11-18 1:40 ` Olof Johansson
0 siblings, 0 replies; 28+ messages in thread
From: Olof Johansson @ 2016-11-18 1:40 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Nov 04, 2016 at 10:44:04AM +0100, Simon Horman wrote:
> Hi Olof, Hi Kevin, Hi Arnd,
>
> Please consider these Renesas ARM64 based SoC DT updates for v4.10.
>
>
> The following changes since commit 1001354ca34179f3db924eb66672442a173147dc:
>
> Linux 4.9-rc1 (2016-10-15 12:17:50 -0700)
>
> are available in the git repository at:
>
> git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-arm64-dt-for-v4.10
>
> for you to fetch changes up to 935085209343a0c507e3d9a3e01883b25c8f743e:
>
> arm64: renesas: r8a7796: add SYS-DMAC controller nodes (2016-11-04 10:18:07 +0100)
>
> ----------------------------------------------------------------
> Renesas ARM64 Based SoC DT Updates for v4.10
>
> Enablement:
> * Enable On-board eMMC
> * Enable SDHI 0 & 3 with UHS
> * Add SYS-DMAC controller nodes to r8a7796 SoC
> * Populate EXTALR on r8a7796/salvator-x board; used by watchdog
> * Add DU LVDS output endpoint on r8a7795/salvator-x board
> * Add bias setting for USB1 pins on r8a7795/salvator-x board
>
> Clean-Up:
> * Remove FCP SoC-specific compatible strings
Thanks, merged.
-Olof
^ permalink raw reply [flat|nested] 28+ messages in thread