[parisc-linux] Re: [parisc-linux-cvs] linux-2.6 willy

[parisc-linux] Re: [parisc-linux-cvs] linux-2.6 willy

[Joel Soete]

Matthew,

2.6.0-test7-pa6 boot well on my b180:
[...]
eth0: Digital DS21143 Tulip rev 65 at 0xff00, 00:10:83:35:2A:A9, IRQ 96.
sym0: <875> rev 0x4 at pci 0000:00:13.0 irq 99
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.18f
Using anticipatory io scheduler
  Vendor: SEAGATE   Model: ST39140WS         Rev: HP03
  Type:   Direct-Access                      ANSI SCSI revision: 02
sym0:5:0: tagged command queuing enabled, command queue depth 16.
  Vendor: SEAGATE   Model: ST39140WS         Rev: HP03
  Type:   Direct-Access                      ANSI SCSI revision: 02
sym0:6:0: tagged command queuing enabled, command queue depth 16.
53c700: Version 2.8 By James.Bottomley@HansenPartnership.com
scsi1: 53c710 rev 2 
scsi1 : LASI SCSI 53c700
st: Version 20030811, fixed bufsize 32768, s/g segs 256
sym0:5: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 15)
SCSI device sda: 17773524 512-byte hdwr sectors (9100 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 >
Attached scsi disk sda at scsi0, channel 0, id 5, lun 0
sym0:6: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 15)
SCSI device sdb: 17773524 512-byte hdwr sectors (9100 MB)
SCSI device sdb: drive cache: write back
 sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 >
Attached scsi disk sdb at scsi0, channel 0, id 6, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 5, lun 0,  type 0
Attached scsi generic sg1 at scsi0, channel 0, id 6, lun 0,  type 0
[...]

I trust that confirm it well uses 'scsi0 : sym-2.1.18f' :)

I run successfully ssh, multi-gnome-terminal, gkrellm and mainly recompile
this kernel with gcc-3.3.2 (20030908). All seems to work fine: uptime 2h25min
:)

Congratulation,
    Joel

>-- Original Message --
>Date: Sun, 12 Oct 2003 10:32:40 +0000
>From: Joel Soete <soete.joel@tiscali.be>
>To:  willy@parisc-linux.org
>Subject: Re: [parisc-linux-cvs] linux-2.6 willy
>
>
>Matthew Wilcox wrote:

>CVSROOT:	/var/cvs
>Module name:	linux-2.6
>Changes by:	willy	03/10/10 13:59:56
>
>Modified files:
>	.              : Makefile 
>
>Log message:
>2.6.0-test7-pa5:
>2.1.18f of the sym driver.  I want people to test this 
>ne.
>  
>
Ok Matthew, I will test it on my b180 on monday

hth,
    Joel





-------------------------------------------------------------------------
L'Internet rapide, c'est pour tout le monde. Tiscali ADSL, 19,50 Euro
pendant 3 mois! http://reg.tiscali.be/default.asp?lg=fr 

[parisc-linux] Re: [parisc-linux-cvs] linux-2.6 willy

[Grant Grundler]

On Sun, Mar 21, 2004 at 03:03:09PM -0700, Matthew Wilcox wrote:
> Log message:
> Patch from Grant Grundler to use REQUEST_SENSE and INQUIRY instead of
> magic numbers.

Ta!

sorry for the "throw it over the fence" on that one.
But it was obvious enough I guess in this case.

thanks,
grant

[parisc-linux] RE: [parisc-linux-cvs] linux-2.6 willy

[Joel Soete]

>CVSROOT:	/var/cvs
>Module name:	linux-2.6
>Changes by:	willy	04/02/17 05:52:36
>
[snip]
>Log message:
>merged to 2.6.3-rc4
Matthew,

Great job.

Boot fine on b2k 64bit kernel build with last gcc-3.0.4-ds3-8 ;)

hth,
    Joel



----------------------------------------------------------------------------------------
Tiscali ADSL: 19,50 €/mois, pendant 3 mois! L'Internet rapide, c'est pour
tout le monde.
http://reg.tiscali.be/default.asp?lg=fr

[parisc-linux] RE: [parisc-linux-cvs] linux-2.6 willy

[Joel Soete]

2.6.0-pa0 boot fine on my b2k :)

Thanks Matthew,
    Joel

PS: build with make defconfig (ie 32bit with gcc 3.3.2-4)

>-- Original Message --
>To: parisc-linux-cvs@lists.parisc-linux.org
>Date: Thu, 18 Dec 2003 07:30:16 -0700 (MST)
>From: willy@parisc-linux.org (Matthew Wilcox)
>Reply-To: parisc-linux@lists.parisc-linux.org
>Subject: [parisc-linux-cvs] linux-2.6 willy
>
>
>CVSROOT:	/var/cvs
Module name:	linux-2.6
Changes by:	willy	03/12/18 07:30:16

Modified files:
	kernel         : Makefile 

Log message:
I may not be tall enough for signals, but I am tall enough for Makefiles!

_______________________________
>_______________
parisc-linux-cvs mailing list
parisc-linux-cvs@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux-cvs



-------------------------------------------------------------------------
Tiscali ADSL: 12 mois à 29,50 €/mois! L'Internet rapide, c'est pour tout
le monde.
http://reg.tiscali.be/default.asp?lg=fr

[parisc-linux] RE: [parisc-linux-cvs] linux-2.6 willy

[Joel Soete]

Hi Matthew,

Sorry but it doesn't help yet to boot the b2k model (always same symptom)
Or do i lost something and should I have to wait for a 32bits_defconfig?

Thanks in advance for additional advise,
Joel

>-- Original Message --
>To: parisc-linux-cvs@lists.parisc-linux.org
>Reply-To: parisc-linux@lists.parisc-linux.org
>From: willy@parisc-linux.org (Matthew Wilcox)
>Date: Thu,  9 Oct 2003 08:00:21 -0600 (MDT)
>Subject: [parisc-linux-cvs] linux-2.6 willy
>
>
>CVSROOT:	/var/cvs
Module name:	linux-2.6
Changes by:	willy	03/10/09 08:00:21

Modified files:
	drivers/serial : 8250.c 8250_gsc.c 

Log message:
Register the serial console from the GSC driver, not just from SuckyIO.
Add a guard to prevent reg
>stering the serial console twice.

_______________________________________________
parisc-linux-cvs mailing list
parisc-linux-cvs@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux-cvs



-------------------------------------------------------------------------
L'Internet rapide, c'est pour tout le monde. Tiscali ADSL, 19,50 Euro
pendant 3 mois! http://reg.tiscali.be/default.asp?lg=fr 

Re: [parisc-linux] RE: [parisc-linux-cvs] linux-2.6 willy

[Matthew Wilcox]

On Thu, Oct 09, 2003 at 07:24:16PM +0200, Joel Soete wrote:
> Hi Matthew,
> 
> Sorry but it doesn't help yet to boot the b2k model (always same symptom)
> Or do i lost something and should I have to wait for a 32bits_defconfig?

I haven't even tried to track down the problems on c3k yet.  I might
get round to it in a week or so.  Other issues are pressing.

-- 
"It's not Hollywood.  War is real, war is primarily not about defeat or
victory, it is about death.  I've seen thousands and thousands of dead bodies.
Do you think I want to have an academic debate on this subject?" -- Robert Fisk

Re: [parisc-linux] RE: [parisc-linux-cvs] linux-2.6 willy

[Joel Soete]

Matthew,

Sorry I just trust that was related to a previous mail :(

In fact I was just looking for a place to put superio_?_init() calls (was
in rs_init() in 2.4?).

Thanks for ypur attention,
    Joel

>-- Original Message --
>Date: Thu, 9 Oct 2003 18:34:36 +0100
>From: Matthew Wilcox <willy@debian.org>
>To: Joel Soete <soete.joel@tiscali.be>
>Cc: parisc-linux@lists.parisc-linux.org
>Subject: Re: [parisc-linux] RE: [parisc-linux-cvs] linux-2.6 willy
>
>
>On Thu, Oct 09, 2003 at 07:24:16PM +0200, Joel Soete wrote:
> Hi Matthew,
> 
> Sorry but it doesn't help yet to boot the b2k model (always same symptom)
> Or do i lost something and should I have to wait for a 32bits_defconfig?

I haven't even tr
>ed to track down the problems on c3k yet.  I might
get round to it in a week or so.  Other issues are pressing.

-- 
"It's not Hollywood.  War is real, war is primarily not about defeat or
victory, it is about death.  I've seen thousands and thous
>nds of dead bodies.
Do you think I want to have an academic debate on this subject?" -- Robert
Fisk



-------------------------------------------------------------------------
L'Internet rapide, c'est pour tout le monde. Tiscali ADSL, 19,50 Euro
pendant 3 mois! http://reg.tiscali.be/default.asp?lg=fr 

[parisc-linux] Re: [parisc-linux-cvs] linux-2.6 willy

[Richard Hirst]

On Sat, Sep 27, 2003 at 01:24:49AM -0600, Matthew Wilcox wrote:
> CVSROOT:	/var/cvs
> Module name:	linux-2.6
> Changes by:	willy	03/09/27 01:24:49
> 
> Modified files:
> 	drivers/scsi   : Makefile NCR_Q720.c ncr53c8xx.c 
> 	                 sym53c8xx_defs.h 
> 
> Log message:
> SIMULATED_INTFLY is always true for ncr720 chips, so remove the other case.

Only because I didn't get it to work properly when I did the original
720 support, iirc.  The chip does have INTFLY.  I _think_ INTFLY worked
a bit, but the driver tended to miss interrupts sometimes.  Could easily
have been a driver bug.  Was a long time ago now though, so I could be
misremembering.

Richard

Re: [parisc-linux] Re: [parisc-linux-cvs] linux-2.6 willy

[James Bottomley]

On Sun, 2003-09-28 at 11:56, Richard Hirst wrote:
> Only because I didn't get it to work properly when I did the original
> 720 support, iirc.  The chip does have INTFLY.  I _think_ INTFLY worked
> a bit, but the driver tended to miss interrupts sometimes.  Could easily
> have been a driver bug.  Was a long time ago now though, so I could be
> misremembering.

Actually, the 720 is bust in silicon.  The 770 has a properly working
intfly, but the 720's doesnt work reliably.  Actually, the Q720 board
this driver also drives is wired to have a special "intfly" from a board
register to get around the problem.

James

Re: [parisc-linux] Re: [parisc-linux-cvs] linux-2.6 willy

[Richard Hirst]

On Sun, Sep 28, 2003 at 12:24:26PM -0500, James Bottomley wrote:
> On Sun, 2003-09-28 at 11:56, Richard Hirst wrote:
> > Only because I didn't get it to work properly when I did the original
> > 720 support, iirc.  The chip does have INTFLY.  I _think_ INTFLY worked
> > a bit, but the driver tended to miss interrupts sometimes.  Could easily
> > have been a driver bug.  Was a long time ago now though, so I could be
> > misremembering.
> 
> Actually, the 720 is bust in silicon.  The 770 has a properly working

OK - explains why it didn't work then.

Cheers,
  Richard

Re: [parisc-linux] Re: [parisc-linux-cvs] linux-2.6 willy

[Matthew Wilcox]

On Sun, Sep 28, 2003 at 12:24:26PM -0500, James Bottomley wrote:
> Actually, the 720 is bust in silicon.  The 770 has a properly working
> intfly, but the 720's doesnt work reliably.  Actually, the Q720 board
> this driver also drives is wired to have a special "intfly" from a board
> register to get around the problem.

Mmm, OK.  Did you want me to put the SIMULATED_INTFLY conditionals
back in?  It wasn't much code; I've just been focused on ripping out
all the 8xx support, and I completely forgot about the 770.

-- 
"It's not Hollywood.  War is real, war is primarily not about defeat or
victory, it is about death.  I've seen thousands and thousands of dead bodies.
Do you think I want to have an academic debate on this subject?" -- Robert Fisk

Re: [parisc-linux] Re: [parisc-linux-cvs] linux-2.6 willy

[James Bottomley]

On Sun, 2003-09-28 at 14:23, Matthew Wilcox wrote:
> On Sun, Sep 28, 2003 at 12:24:26PM -0500, James Bottomley wrote:
> > Actually, the 720 is bust in silicon.  The 770 has a properly working
> > intfly, but the 720's doesnt work reliably.  Actually, the Q720 board
> > this driver also drives is wired to have a special "intfly" from a board
> > register to get around the problem.
> 
> Mmm, OK.  Did you want me to put the SIMULATED_INTFLY conditionals
> back in?  It wasn't much code; I've just been focused on ripping out
> all the 8xx support, and I completely forgot about the 770.

Perhaps.  The way I'd envisaged going forwards was to put the Q720 code
in there...it does a memory move which causes the card to trigger and
interrupt which can be used as an INTFLY.

Unfortunately, I lost all my Q770 cards in a lab move, so I've no means
of testing them.

James