From: Mauro Carvalho Chehab <mchehab@s-opensource.com>
To: Linux Media Mailing List <linux-media@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>,
Mauro Carvalho Chehab <mchehab@infradead.org>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
Javier Martinez Canillas <javier@osg.samsung.com>,
Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
"Lad, Prabhakar" <prabhakar.csengg@gmail.com>,
Hans Verkuil <hans.verkuil@cisco.com>,
Mauro Carvalho Chehab <mchehab@s-opensource.com>
Subject: [PATCH 32/35] [media] tvp5150: Get rid of direct calls to printk()
Date: Wed, 16 Nov 2016 14:43:04 -0200 [thread overview]
Message-ID: <3a4777867f0781fc7f8632483972ed28084cfd62.1479314177.git.mchehab@s-opensource.com> (raw)
In-Reply-To: <cover.1479314177.git.mchehab@s-opensource.com>
In-Reply-To: <cover.1479314177.git.mchehab@s-opensource.com>
From: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When returning results via v4l2_subdev_core_ops.log_status,
use dev_foo() call, instead of just calling printk()
directly, without even specifying the log message level.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
---
drivers/media/i2c/tvp5150.c | 218 ++++++++++++++++++++++----------------------
1 file changed, 110 insertions(+), 108 deletions(-)
diff --git a/drivers/media/i2c/tvp5150.c b/drivers/media/i2c/tvp5150.c
index 569eb7c0968a..d0dbdd7ea233 100644
--- a/drivers/media/i2c/tvp5150.c
+++ b/drivers/media/i2c/tvp5150.c
@@ -36,6 +36,8 @@ static int debug;
module_param(debug, int, 0644);
MODULE_PARM_DESC(debug, "Debug level (0-2)");
+#define dprintk0(__dev, __arg...) dev_dbg_lvl(__dev, 0, 0, __arg)
+
struct tvp5150 {
struct v4l2_subdev sd;
#ifdef CONFIG_MEDIA_CONTROLLER
@@ -118,120 +120,120 @@ static void dump_reg_range(struct v4l2_subdev *sd, char *s, u8 init,
static int tvp5150_log_status(struct v4l2_subdev *sd)
{
- printk("tvp5150: Video input source selection #1 = 0x%02x\n",
- tvp5150_read(sd, TVP5150_VD_IN_SRC_SEL_1));
- printk("tvp5150: Analog channel controls = 0x%02x\n",
- tvp5150_read(sd, TVP5150_ANAL_CHL_CTL));
- printk("tvp5150: Operation mode controls = 0x%02x\n",
- tvp5150_read(sd, TVP5150_OP_MODE_CTL));
- printk("tvp5150: Miscellaneous controls = 0x%02x\n",
- tvp5150_read(sd, TVP5150_MISC_CTL));
- printk("tvp5150: Autoswitch mask= 0x%02x\n",
- tvp5150_read(sd, TVP5150_AUTOSW_MSK));
- printk("tvp5150: Color killer threshold control = 0x%02x\n",
- tvp5150_read(sd, TVP5150_COLOR_KIL_THSH_CTL));
- printk("tvp5150: Luminance processing controls #1 #2 and #3 = %02x %02x %02x\n",
- tvp5150_read(sd, TVP5150_LUMA_PROC_CTL_1),
- tvp5150_read(sd, TVP5150_LUMA_PROC_CTL_2),
- tvp5150_read(sd, TVP5150_LUMA_PROC_CTL_3));
- printk("tvp5150: Brightness control = 0x%02x\n",
- tvp5150_read(sd, TVP5150_BRIGHT_CTL));
- printk("tvp5150: Color saturation control = 0x%02x\n",
- tvp5150_read(sd, TVP5150_SATURATION_CTL));
- printk("tvp5150: Hue control = 0x%02x\n",
- tvp5150_read(sd, TVP5150_HUE_CTL));
- printk("tvp5150: Contrast control = 0x%02x\n",
- tvp5150_read(sd, TVP5150_CONTRAST_CTL));
- printk("tvp5150: Outputs and data rates select = 0x%02x\n",
- tvp5150_read(sd, TVP5150_DATA_RATE_SEL));
- printk("tvp5150: Configuration shared pins = 0x%02x\n",
- tvp5150_read(sd, TVP5150_CONF_SHARED_PIN));
- printk("tvp5150: Active video cropping start = 0x%02x%02x\n",
- tvp5150_read(sd, TVP5150_ACT_VD_CROP_ST_MSB),
- tvp5150_read(sd, TVP5150_ACT_VD_CROP_ST_LSB));
- printk("tvp5150: Active video cropping stop = 0x%02x%02x\n",
- tvp5150_read(sd, TVP5150_ACT_VD_CROP_STP_MSB),
- tvp5150_read(sd, TVP5150_ACT_VD_CROP_STP_LSB));
- printk("tvp5150: Genlock/RTC = 0x%02x\n",
- tvp5150_read(sd, TVP5150_GENLOCK));
- printk("tvp5150: Horizontal sync start = 0x%02x\n",
- tvp5150_read(sd, TVP5150_HORIZ_SYNC_START));
- printk("tvp5150: Vertical blanking start = 0x%02x\n",
- tvp5150_read(sd, TVP5150_VERT_BLANKING_START));
- printk("tvp5150: Vertical blanking stop = 0x%02x\n",
- tvp5150_read(sd, TVP5150_VERT_BLANKING_STOP));
- printk("tvp5150: Chrominance processing control #1 and #2 = %02x %02x\n",
- tvp5150_read(sd, TVP5150_CHROMA_PROC_CTL_1),
- tvp5150_read(sd, TVP5150_CHROMA_PROC_CTL_2));
- printk("tvp5150: Interrupt reset register B = 0x%02x\n",
- tvp5150_read(sd, TVP5150_INT_RESET_REG_B));
- printk("tvp5150: Interrupt enable register B = 0x%02x\n",
- tvp5150_read(sd, TVP5150_INT_ENABLE_REG_B));
- printk("tvp5150: Interrupt configuration register B = 0x%02x\n",
- tvp5150_read(sd, TVP5150_INTT_CONFIG_REG_B));
- printk("tvp5150: Video standard = 0x%02x\n",
- tvp5150_read(sd, TVP5150_VIDEO_STD));
- printk("tvp5150: Chroma gain factor: Cb=0x%02x Cr=0x%02x\n",
- tvp5150_read(sd, TVP5150_CB_GAIN_FACT),
- tvp5150_read(sd, TVP5150_CR_GAIN_FACTOR));
- printk("tvp5150: Macrovision on counter = 0x%02x\n",
- tvp5150_read(sd, TVP5150_MACROVISION_ON_CTR));
- printk("tvp5150: Macrovision off counter = 0x%02x\n",
- tvp5150_read(sd, TVP5150_MACROVISION_OFF_CTR));
- printk("tvp5150: ITU-R BT.656.%d timing(TVP5150AM1 only)\n",
- (tvp5150_read(sd, TVP5150_REV_SELECT) & 1) ? 3 : 4);
- printk("tvp5150: Device ID = %02x%02x\n",
- tvp5150_read(sd, TVP5150_MSB_DEV_ID),
- tvp5150_read(sd, TVP5150_LSB_DEV_ID));
- printk("tvp5150: ROM version = (hex) %02x.%02x\n",
- tvp5150_read(sd, TVP5150_ROM_MAJOR_VER),
- tvp5150_read(sd, TVP5150_ROM_MINOR_VER));
- printk("tvp5150: Vertical line count = 0x%02x%02x\n",
- tvp5150_read(sd, TVP5150_VERT_LN_COUNT_MSB),
- tvp5150_read(sd, TVP5150_VERT_LN_COUNT_LSB));
- printk("tvp5150: Interrupt status register B = 0x%02x\n",
- tvp5150_read(sd, TVP5150_INT_STATUS_REG_B));
- printk("tvp5150: Interrupt active register B = 0x%02x\n",
- tvp5150_read(sd, TVP5150_INT_ACTIVE_REG_B));
- printk("tvp5150: Status regs #1 to #5 = %02x %02x %02x %02x %02x\n",
- tvp5150_read(sd, TVP5150_STATUS_REG_1),
- tvp5150_read(sd, TVP5150_STATUS_REG_2),
- tvp5150_read(sd, TVP5150_STATUS_REG_3),
- tvp5150_read(sd, TVP5150_STATUS_REG_4),
- tvp5150_read(sd, TVP5150_STATUS_REG_5));
+ dprintk0(sd->dev, "tvp5150: Video input source selection #1 = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_VD_IN_SRC_SEL_1));
+ dprintk0(sd->dev, "tvp5150: Analog channel controls = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_ANAL_CHL_CTL));
+ dprintk0(sd->dev, "tvp5150: Operation mode controls = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_OP_MODE_CTL));
+ dprintk0(sd->dev, "tvp5150: Miscellaneous controls = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_MISC_CTL));
+ dprintk0(sd->dev, "tvp5150: Autoswitch mask= 0x%02x\n",
+ tvp5150_read(sd, TVP5150_AUTOSW_MSK));
+ dprintk0(sd->dev, "tvp5150: Color killer threshold control = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_COLOR_KIL_THSH_CTL));
+ dprintk0(sd->dev, "tvp5150: Luminance processing controls #1 #2 and #3 = %02x %02x %02x\n",
+ tvp5150_read(sd, TVP5150_LUMA_PROC_CTL_1),
+ tvp5150_read(sd, TVP5150_LUMA_PROC_CTL_2),
+ tvp5150_read(sd, TVP5150_LUMA_PROC_CTL_3));
+ dprintk0(sd->dev, "tvp5150: Brightness control = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_BRIGHT_CTL));
+ dprintk0(sd->dev, "tvp5150: Color saturation control = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_SATURATION_CTL));
+ dprintk0(sd->dev, "tvp5150: Hue control = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_HUE_CTL));
+ dprintk0(sd->dev, "tvp5150: Contrast control = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_CONTRAST_CTL));
+ dprintk0(sd->dev, "tvp5150: Outputs and data rates select = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_DATA_RATE_SEL));
+ dprintk0(sd->dev, "tvp5150: Configuration shared pins = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_CONF_SHARED_PIN));
+ dprintk0(sd->dev, "tvp5150: Active video cropping start = 0x%02x%02x\n",
+ tvp5150_read(sd, TVP5150_ACT_VD_CROP_ST_MSB),
+ tvp5150_read(sd, TVP5150_ACT_VD_CROP_ST_LSB));
+ dprintk0(sd->dev, "tvp5150: Active video cropping stop = 0x%02x%02x\n",
+ tvp5150_read(sd, TVP5150_ACT_VD_CROP_STP_MSB),
+ tvp5150_read(sd, TVP5150_ACT_VD_CROP_STP_LSB));
+ dprintk0(sd->dev, "tvp5150: Genlock/RTC = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_GENLOCK));
+ dprintk0(sd->dev, "tvp5150: Horizontal sync start = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_HORIZ_SYNC_START));
+ dprintk0(sd->dev, "tvp5150: Vertical blanking start = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_VERT_BLANKING_START));
+ dprintk0(sd->dev, "tvp5150: Vertical blanking stop = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_VERT_BLANKING_STOP));
+ dprintk0(sd->dev, "tvp5150: Chrominance processing control #1 and #2 = %02x %02x\n",
+ tvp5150_read(sd, TVP5150_CHROMA_PROC_CTL_1),
+ tvp5150_read(sd, TVP5150_CHROMA_PROC_CTL_2));
+ dprintk0(sd->dev, "tvp5150: Interrupt reset register B = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_INT_RESET_REG_B));
+ dprintk0(sd->dev, "tvp5150: Interrupt enable register B = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_INT_ENABLE_REG_B));
+ dprintk0(sd->dev, "tvp5150: Interrupt configuration register B = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_INTT_CONFIG_REG_B));
+ dprintk0(sd->dev, "tvp5150: Video standard = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_VIDEO_STD));
+ dprintk0(sd->dev, "tvp5150: Chroma gain factor: Cb=0x%02x Cr=0x%02x\n",
+ tvp5150_read(sd, TVP5150_CB_GAIN_FACT),
+ tvp5150_read(sd, TVP5150_CR_GAIN_FACTOR));
+ dprintk0(sd->dev, "tvp5150: Macrovision on counter = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_MACROVISION_ON_CTR));
+ dprintk0(sd->dev, "tvp5150: Macrovision off counter = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_MACROVISION_OFF_CTR));
+ dprintk0(sd->dev, "tvp5150: ITU-R BT.656.%d timing(TVP5150AM1 only)\n",
+ (tvp5150_read(sd, TVP5150_REV_SELECT) & 1) ? 3 : 4);
+ dprintk0(sd->dev, "tvp5150: Device ID = %02x%02x\n",
+ tvp5150_read(sd, TVP5150_MSB_DEV_ID),
+ tvp5150_read(sd, TVP5150_LSB_DEV_ID));
+ dprintk0(sd->dev, "tvp5150: ROM version = (hex) %02x.%02x\n",
+ tvp5150_read(sd, TVP5150_ROM_MAJOR_VER),
+ tvp5150_read(sd, TVP5150_ROM_MINOR_VER));
+ dprintk0(sd->dev, "tvp5150: Vertical line count = 0x%02x%02x\n",
+ tvp5150_read(sd, TVP5150_VERT_LN_COUNT_MSB),
+ tvp5150_read(sd, TVP5150_VERT_LN_COUNT_LSB));
+ dprintk0(sd->dev, "tvp5150: Interrupt status register B = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_INT_STATUS_REG_B));
+ dprintk0(sd->dev, "tvp5150: Interrupt active register B = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_INT_ACTIVE_REG_B));
+ dprintk0(sd->dev, "tvp5150: Status regs #1 to #5 = %02x %02x %02x %02x %02x\n",
+ tvp5150_read(sd, TVP5150_STATUS_REG_1),
+ tvp5150_read(sd, TVP5150_STATUS_REG_2),
+ tvp5150_read(sd, TVP5150_STATUS_REG_3),
+ tvp5150_read(sd, TVP5150_STATUS_REG_4),
+ tvp5150_read(sd, TVP5150_STATUS_REG_5));
dump_reg_range(sd, "Teletext filter 1", TVP5150_TELETEXT_FIL1_INI,
TVP5150_TELETEXT_FIL1_END, 8);
dump_reg_range(sd, "Teletext filter 2", TVP5150_TELETEXT_FIL2_INI,
TVP5150_TELETEXT_FIL2_END, 8);
- printk("tvp5150: Teletext filter enable = 0x%02x\n",
- tvp5150_read(sd, TVP5150_TELETEXT_FIL_ENA));
- printk("tvp5150: Interrupt status register A = 0x%02x\n",
- tvp5150_read(sd, TVP5150_INT_STATUS_REG_A));
- printk("tvp5150: Interrupt enable register A = 0x%02x\n",
- tvp5150_read(sd, TVP5150_INT_ENABLE_REG_A));
- printk("tvp5150: Interrupt configuration = 0x%02x\n",
- tvp5150_read(sd, TVP5150_INT_CONF));
- printk("tvp5150: VDP status register = 0x%02x\n",
- tvp5150_read(sd, TVP5150_VDP_STATUS_REG));
- printk("tvp5150: FIFO word count = 0x%02x\n",
- tvp5150_read(sd, TVP5150_FIFO_WORD_COUNT));
- printk("tvp5150: FIFO interrupt threshold = 0x%02x\n",
- tvp5150_read(sd, TVP5150_FIFO_INT_THRESHOLD));
- printk("tvp5150: FIFO reset = 0x%02x\n",
- tvp5150_read(sd, TVP5150_FIFO_RESET));
- printk("tvp5150: Line number interrupt = 0x%02x\n",
- tvp5150_read(sd, TVP5150_LINE_NUMBER_INT));
- printk("tvp5150: Pixel alignment register = 0x%02x%02x\n",
- tvp5150_read(sd, TVP5150_PIX_ALIGN_REG_HIGH),
- tvp5150_read(sd, TVP5150_PIX_ALIGN_REG_LOW));
- printk("tvp5150: FIFO output control = 0x%02x\n",
- tvp5150_read(sd, TVP5150_FIFO_OUT_CTRL));
- printk("tvp5150: Full field enable = 0x%02x\n",
- tvp5150_read(sd, TVP5150_FULL_FIELD_ENA));
- printk("tvp5150: Full field mode register = 0x%02x\n",
- tvp5150_read(sd, TVP5150_FULL_FIELD_MODE_REG));
+ dprintk0(sd->dev, "tvp5150: Teletext filter enable = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_TELETEXT_FIL_ENA));
+ dprintk0(sd->dev, "tvp5150: Interrupt status register A = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_INT_STATUS_REG_A));
+ dprintk0(sd->dev, "tvp5150: Interrupt enable register A = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_INT_ENABLE_REG_A));
+ dprintk0(sd->dev, "tvp5150: Interrupt configuration = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_INT_CONF));
+ dprintk0(sd->dev, "tvp5150: VDP status register = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_VDP_STATUS_REG));
+ dprintk0(sd->dev, "tvp5150: FIFO word count = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_FIFO_WORD_COUNT));
+ dprintk0(sd->dev, "tvp5150: FIFO interrupt threshold = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_FIFO_INT_THRESHOLD));
+ dprintk0(sd->dev, "tvp5150: FIFO reset = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_FIFO_RESET));
+ dprintk0(sd->dev, "tvp5150: Line number interrupt = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_LINE_NUMBER_INT));
+ dprintk0(sd->dev, "tvp5150: Pixel alignment register = 0x%02x%02x\n",
+ tvp5150_read(sd, TVP5150_PIX_ALIGN_REG_HIGH),
+ tvp5150_read(sd, TVP5150_PIX_ALIGN_REG_LOW));
+ dprintk0(sd->dev, "tvp5150: FIFO output control = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_FIFO_OUT_CTRL));
+ dprintk0(sd->dev, "tvp5150: Full field enable = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_FULL_FIELD_ENA));
+ dprintk0(sd->dev, "tvp5150: Full field mode register = 0x%02x\n",
+ tvp5150_read(sd, TVP5150_FULL_FIELD_MODE_REG));
dump_reg_range(sd, "CC data", TVP5150_CC_DATA_INI,
TVP5150_CC_DATA_END, 8);
--
2.7.4
next prev parent reply other threads:[~2016-11-16 16:43 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-11-16 16:42 [PATCH 00/35] Some printk fixups and improvements Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 01/35] [media] stb0899_drv: get rid of continuation lines Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 02/35] [media] stv090x: " Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 03/35] [media] bt8xx/dst: use a more standard way to print messages Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 04/35] [media] bt8xx: use pr_foo() macros instead of printk() Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 05/35] [media] cx23885: use KERN_CONT where needed Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 06/35] [media] cx23885: convert it to use pr_foo() macros Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 07/35] [media] cx88: use KERN_CONT where needed Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 08/35] [media] cx88: convert it to use pr_foo() macros Mauro Carvalho Chehab
2016-11-18 22:27 ` Andrey Utkin
2016-11-19 12:16 ` Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 09/35] [media] cx88: make checkpatch happier Mauro Carvalho Chehab
2016-11-18 22:25 ` Andrey Utkin
2016-11-19 12:14 ` Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 10/35] [media] pluto2: use KERN_CONT where needed Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 11/35] [media] zoran: " Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 12/35] [media] wl128x: use KERNEL_CONT " Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 13/35] [media] pvrusb2: " Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 14/35] [media] ttusb_dec: " Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 15/35] [media] ttpci: cleanup debug macros and remove dead code Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 16/35] [media] dib0070: use pr_foo() instead of printk() Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 17/35] [media] dib0090: " Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 18/35] [media] dib3000mb: " Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 19/35] [media] dib3000mc: " Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 20/35] [media] dib7000m: " Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 21/35] [media] dib7000p: " Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 22/35] [media] dib8000: " Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 23/35] [media] dib9000: " Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 24/35] [media] dibx000_common: " Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 25/35] [media] af9005: remove a printk that would require a KERN_CONT Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 26/35] [media] tuner-core: use pr_foo, instead of internal printk macros Mauro Carvalho Chehab
2016-11-16 16:42 ` [PATCH 27/35] [media] v4l2-common: add a debug macro to be used with dev_foo() Mauro Carvalho Chehab
2016-11-16 16:43 ` [PATCH 28/35] [media] msp3400-driver: don't use KERN_CONT Mauro Carvalho Chehab
2016-11-16 16:43 ` [PATCH 29/35] [media] msp3400: convert it to use dev_foo() macros Mauro Carvalho Chehab
2016-11-16 16:43 ` [PATCH 30/35] [media] em28xx: convert it from pr_foo() to dev_foo() Mauro Carvalho Chehab
2016-11-16 16:43 ` [PATCH 31/35] [media] tvp5150: convert it to use dev_foo() macros Mauro Carvalho Chehab
2016-11-16 16:43 ` Mauro Carvalho Chehab [this message]
2016-11-16 16:43 ` [PATCH 33/35] [media] tvp5150: get rid of KERN_CONT Mauro Carvalho Chehab
2016-11-16 16:43 ` [PATCH 34/35] [media] rc-main: use pr_foo() macros Mauro Carvalho Chehab
2016-11-16 16:43 ` [PATCH 35/35] [media] tveeprom: print log messages using pr_foo() Mauro Carvalho Chehab
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3a4777867f0781fc7f8632483972ed28084cfd62.1479314177.git.mchehab@s-opensource.com \
--to=mchehab@s-opensource.com \
--cc=hans.verkuil@cisco.com \
--cc=javier@osg.samsung.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@infradead.org \
--cc=mchehab@kernel.org \
--cc=mchehab@osg.samsung.com \
--cc=prabhakar.csengg@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.