* 2.6.1/aic7xxx: "Unexpected busfree in Message-out phase" during boot
@ 2004-01-19 11:18 Ulrich Windl
0 siblings, 0 replies; only message in thread
From: Ulrich Windl @ 2004-01-19 11:18 UTC (permalink / raw)
To: linux-scsi
[-- Attachment #1: Mail message body --]
[-- Type: text/plain, Size: 460 bytes --]
Hi,
I'm not subscribed to this list, so please consider that when replying.
I've tried Linux-2.6.1 on my Hardware running 2.4 without problems:
During boot I'm getting a "Unexpected busfree in Message-out phase" for my
AHA2940 and my harddisk. I'm attaching "dmesg" output (19kB) and some PCI and
SCSI information. I guess it's a programming error, maybe related to kernel
preemption.
I would try any patches to have the problem fixed.
Regards,
Ulrich
[-- Attachment #2: 2.6.1.msg --]
[-- Type: Application/Octet-stream, Size: 19841 bytes --]
Kernel Messages (dmesg):
------------------------
(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c596b (rev 23) IDE UDMA66 controller on pci0000:00:07.1
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:pio, hdd:pio
hda: IC35L040AVVA07-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 80418240 sectors (41174 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(66)
hda: hda1 hda2 < hda5 >
PCI: Found IRQ 9 for device 0000:00:0a.0
ahc_pci:0:10:0: Reading SEEPROM...done.
ahc_pci:0:10:0: internal 50 cable is present
ahc_pci:0:10:0: external cable not present
ahc_pci:0:10:0: BIOS eeprom not present
ahc_pci:0:10:0: Low byte termination Enabled
ahc_pci:0:10:0: Downloading Sequencer Program... 438 instructions downloaded
ahc_pci:0:10:0: Features 0x0, Bugs 0x25, Flags 0x30481500
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2940 SCSI adapter>
aic7870: Single Channel A, SCSI Id=7, 16/253 SCBs
scsi0: Slave Alloc 0
(scsi0:A:0:0): Sending SDTR period 45, offset 0
(scsi0:A:0:0): Received SDTR period 45, offset 0
Filtered to period 0, offset 0
(scsi0:A:0): 3.300MB/s transfers
scsi0: target 0 using asynchronous transfers
(scsi0:A:1:0): Sending SDTR period 45, offset 0
(scsi0:A:1:0): Received SDTR period 45, offset 0
Filtered to period 0, offset 0
(scsi0:A:1): 3.300MB/s transfers
scsi0: target 1 using asynchronous transfers
(scsi0:A:2:0): Sending SDTR period 45, offset 0
(scsi0:A:2:0): Received SDTR period 45, offset 0
Filtered to period 0, offset 0
(scsi0:A:2): 3.300MB/s transfers
scsi0: target 2 using asynchronous transfers
(scsi0:A:0:0): Sending SDTR period 19, offset f
(scsi0:A:0:0): Received SDTR period 19, offset f
Filtered to period 19, offset f
(scsi0:A:0): 10.000MB/s transfers (10.000MHz, offset 15)
scsi0: target 0 synchronous at 10.0MHz, offset = 0xf
Vendor: IBM Model: DPSS-318350N Rev: S96H
Type: Direct-Access ANSI SCSI revision: 03
scsi0: Slave Configure 0
(scsi0:A:0): 10.000MB/s transfers (10.000MHz, offset 15)
scsi0:A:0:0: Tagged Queuing enabled. Depth 16
scsi0: Slave Alloc 0
scsi0: Slave Destroy 0
scsi0: Slave Alloc 1
(scsi0:A:1:0): Sending SDTR period 19, offset f
(scsi0:A:1:0): Received SDTR period 3b, offset f
Filtered to period 3b, offset f
(scsi0:A:1): 4.237MB/s transfers (4.237MHz, offset 15)
scsi0: target 1 synchronous at 4.0MHz, offset = 0xf
Vendor: TOSHIBA Model: CD-ROM XM-5301TA Rev: 1895
Type: CD-ROM ANSI SCSI revision: 02
scsi0: Slave Configure 1
(scsi0:A:1): 4.237MB/s transfers (4.237MHz, offset 15)
scsi0: Slave Alloc 1
scsi0: Slave Destroy 1
scsi0: Slave Alloc 2
(scsi0:A:2:0): Sending SDTR period 19, offset f
(scsi0:A:2:0): Received SDTR period 32, offset 8
Filtered to period 32, offset 8
(scsi0:A:2): 5.000MB/s transfers (5.000MHz, offset 8)
scsi0: target 2 synchronous at 5.0MHz, offset = 0x8
Vendor: HP Model: HP35480A Rev: T603
Type: Sequential-Access ANSI SCSI revision: 02
scsi0: Slave Configure 2
(scsi0:A:2): 5.000MB/s transfers (5.000MHz, offset 8)
scsi0: Slave Alloc 2
scsi0: Slave Destroy 2
scsi0: Slave Alloc 3
scsi0: Slave Destroy 3
scsi0: Slave Alloc 4
scsi0: Slave Destroy 4
scsi0: Slave Alloc 5
scsi0: Slave Destroy 5
scsi0: Slave Alloc 6
scsi0: Slave Destroy 6
SCSI device sda: 35843670 512-byte hdwr sectors (18352 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: PS/2 Generic Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 152k freed
(scsi0:A:0:0): Unexpected busfree in Message-out phase
SEQADDR == 0x165
(scsi0:A:0:0): Sending SDTR period 19, offset f
(scsi0:A:0:0): Received SDTR period 19, offset f
Filtered to period 19, offset f
(scsi0:A:0:0): Unexpected busfree in Message-out phase
SEQADDR == 0x165
(scsi0:A:0:0): Sending SDTR period 19, offset f
(scsi0:A:0:0): Received SDTR period 19, offset f
Filtered to period 19, offset f
(scsi0:A:0:0): Sending SDTR period 19, offset f
(scsi0:A:0:0): Received SDTR period 19, offset f
Filtered to period 19, offset f
scsi0:0:0:0: Attempting to queue an ABORT message
CDB: 0x28 0x0 0x0 0x5e 0x2e 0x9 0x0 0x0 0x8 0x0
scsi0: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi0: Dumping Card State while idle, at SEQADDR 0x8
Card was paused
ACCUM = 0x79, SINDEX = 0x3, DINDEX = 0x8c, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x3
SCSISIGI[0x0] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x1]:(P_BUSFREE)
SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI) SBLKCTL[0x0] SCSIRATE[0x0]
SEQCTL[0x30]:(FASTMODE|FAILDIS) SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED)
SSTAT0[0x5]:(DMADONE|SDONE) SSTAT1[0xa]:(PHASECHG|BUSFREE)
SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO)
SXFRCTL0[0x80]:(DFON) DFCNTRL[0x0] DFSTATUS[0x29]:(FIFOEMP|HDONE|FIFOQWDEMP)
STACK: 0xd2 0x15f 0x102 0x3
SCB count = 8
Kernel NEXTQSCB = 7
Card NEXTQSCB = 7
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries: 0:0 1:2 2:1
QOUTFIFO entries:
Sequencer Free SCB List: 3 4 5 6 7 8 9 10 11 12 13 14 15
Sequencer SCB Info:
0 SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x0]
1 SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x2]
2 SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x1]
3 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
Pending list:
0 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
2 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
1 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
Kernel Free SCB list: 3 6 5 4
DevQ(0:0:0): 0 waiting
DevQ(0:1:0): 0 waiting
DevQ(0:2:0): 0 waiting
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
(scsi0:A:0:0): Device is disconnected, re-queuing SCB
(scsi0:A:0:0): Abort Tag Message Sent
Recovery code sleeping
(scsi0:A:0:0): SCB 1 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 0x2002
scsi0:0:0:0: Attempting to queue an ABORT message
CDB: 0x28 0x0 0x0 0x5e 0x2d 0xc9 0x0 0x0 0x38 0x0
scsi0: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi0: Dumping Card State while idle, at SEQADDR 0x7
Card was paused
ACCUM = 0x7b, SINDEX = 0x7, DINDEX = 0x8c, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x2
SCSISIGI[0x0] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x1]:(P_BUSFREE)
SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI) SBLKCTL[0x0] SCSIRATE[0x0]
SEQCTL[0x30]:(FASTMODE|FAILDIS) SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED)
SSTAT0[0x5]:(DMADONE|SDONE) SSTAT1[0xa]:(PHASECHG|BUSFREE)
SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO)
SXFRCTL0[0x80]:(DFON) DFCNTRL[0x0] DFSTATUS[0x29]:(FIFOEMP|HDONE|FIFOQWDEMP)
STACK: 0xe1 0x15f 0x102 0x3
SCB count = 8
Kernel NEXTQSCB = 1
Card NEXTQSCB = 1
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries: 0:0 1:2
QOUTFIFO entries:
Sequencer Free SCB List: 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Sequencer SCB Info:
0 SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x0]
1 SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x2]
2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
3 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
Pending list:
0 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
2 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
Kernel Free SCB list: 7 3 6 5 4
DevQ(0:0:0): 0 waiting
DevQ(0:1:0): 0 waiting
DevQ(0:2:0): 0 waiting
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
(scsi0:A:0:0): Device is disconnected, re-queuing SCB
(scsi0:A:0:0): Abort Tag Message Sent
Recovery code sleeping
(scsi0:A:0:0): SCB 2 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 0x2002
scsi0:0:0:0: Attempting to queue an ABORT message
CDB: 0x28 0x0 0x0 0x5c 0x92 0x99 0x0 0x0 0x20 0x0
scsi0: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi0: Dumping Card State while idle, at SEQADDR 0x8
Card was paused
ACCUM = 0x7d, SINDEX = 0x1, DINDEX = 0x8c, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x1
SCSISIGI[0x0] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x1]:(P_BUSFREE)
SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI) SBLKCTL[0x0] SCSIRATE[0x0]
SEQCTL[0x30]:(FASTMODE|FAILDIS) SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED)
SSTAT0[0x5]:(DMADONE|SDONE) SSTAT1[0xa]:(PHASECHG|BUSFREE)
SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO)
SXFRCTL0[0x80]:(DFON) DFCNTRL[0x0] DFSTATUS[0x29]:(FIFOEMP|HDONE|FIFOQWDEMP)
STACK: 0xe1 0x15f 0x102 0x3
SCB count = 8
Kernel NEXTQSCB = 2
Card NEXTQSCB = 2
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries: 0:0
QOUTFIFO entries:
Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Sequencer SCB Info:
0 SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x0]
1 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
3 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
Pending list:
0 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
Kernel Free SCB list: 1 7 3 6 5 4
DevQ(0:0:0): 0 waiting
DevQ(0:1:0): 0 waiting
DevQ(0:2:0): 0 waiting
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
(scsi0:A:0:0): Device is disconnected, re-queuing SCB
(scsi0:A:0:0): Abort Tag Message Sent
Recovery code sleeping
(scsi0:A:0:0): SCB 0 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 0x2002
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
serio: kseriod exiting
request_module: failed /sbin/modprobe -- ntfs. error = 256
lspci -v:
---------
00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev 44)
Flags: bus master, medium devsel, latency 0
Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: e4000000-e5ffffff
Prefetchable memory behind bridge: d8000000-dfffffff
Capabilities: [80] Power Management version 2
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C596 ISA [Mobile South] (rev 23)
Subsystem: VIA Technologies, Inc. VT82C596/A/B PCI to ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 10) (prog-if 8a [Master SecP PriP])
Flags: bus master, medium devsel, latency 64
I/O ports at e000 [size=16]
Capabilities: [c0] Power Management version 2
00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 11) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 64, IRQ 9
I/O ports at e400 [size=32]
Capabilities: [80] Power Management version 2
00:07.3 Host bridge: VIA Technologies, Inc. VT82C596 Power Management (rev 30)
Flags: medium devsel
00:0a.0 SCSI storage controller: Adaptec AHA-2940/2940W / AIC-7871 (rev 03)
Flags: bus master, medium devsel, latency 64, IRQ 9
I/O ports at e800 [disabled] [size=256]
Memory at e7000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at e6000000 [disabled] [size=64K]
01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev a1) (prog-if 00 [VGA])
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 11
Memory at e4000000 (32-bit, non-prefetchable) [size=16M]
Memory at d8000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Capabilities: [44] AGP version 2.0
cat /proc/scsi/scsi:
--------------------
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: IBM Model: DPSS-318350N Rev: S96H
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: TOSHIBA Model: CD-ROM XM-5301TA Rev: 1895
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 02 Lun: 00
Vendor: HP Model: HP35480A Rev: T603
Type: Sequential-Access ANSI SCSI revision: 02
cat /proc/scssi/aic7xxx/0:
--------------------------
Adaptec AIC7xxx driver version: 6.2.36
Adaptec 2940 SCSI adapter
aic7870: Single Channel A, SCSI Id=7, 16/253 SCBs
Allocated SCBs: 8, SG List Length: 128
Serial EEPROM:
0x0318 0x0218 0x0218 0x0210 0x0210 0x0210 0x0210 0x0210
0x0238 0x0238 0x0238 0x0238 0x0238 0x0238 0x0238 0x0238
0x1996 0x0019 0x2807 0x0008 0xff00 0xffff 0xffff 0xffff
0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0x00ff 0x650c
Target 0 Negotiation Settings
User: 10.000MB/s transfers (10.000MHz, offset 127)
Goal: 10.000MB/s transfers (10.000MHz, offset 15)
Curr: 10.000MB/s transfers (10.000MHz, offset 15)
Channel A Target 0 Lun 0 Settings
Commands Queued 667
Commands Active 0
Command Openings 16
Max Tagged Openings 16
Device Queue Frozen Count 0
Target 1 Negotiation Settings
User: 10.000MB/s transfers (10.000MHz, offset 127)
Goal: 4.237MB/s transfers (4.237MHz, offset 15)
Curr: 4.237MB/s transfers (4.237MHz, offset 15)
Channel A Target 1 Lun 0 Settings
Commands Queued 2
Commands Active 0
Command Openings 1
Max Tagged Openings 0
Device Queue Frozen Count 0
Target 2 Negotiation Settings
User: 10.000MB/s transfers (10.000MHz, offset 127)
Goal: 5.000MB/s transfers (5.000MHz, offset 8)
Curr: 5.000MB/s transfers (5.000MHz, offset 8)
Channel A Target 2 Lun 0 Settings
Commands Queued 2
Commands Active 0
Command Openings 1
Max Tagged Openings 0
Device Queue Frozen Count 0
Target 3 Negotiation Settings
User: 3.300MB/s transfers
Target 4 Negotiation Settings
User: 3.300MB/s transfers
Target 5 Negotiation Settings
User: 3.300MB/s transfers
Target 6 Negotiation Settings
User: 3.300MB/s transfers
Target 7 Negotiation Settings
User: 3.300MB/s transfers
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2004-01-19 11:18 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2004-01-19 11:18 2.6.1/aic7xxx: "Unexpected busfree in Message-out phase" during boot Ulrich Windl
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.