[U-Boot] [PATCH 1/2] ARM: dts: imx6qdl: Add device tree support for SolidRun Cubox-i

* [U-Boot] [PATCH 1/2] ARM: dts: imx6qdl: Add device tree support for SolidRun Cubox-i
@ 2019-10-28 14:00 Walter Lozano
  2019-10-28 14:00 ` [U-Boot] [PATCH 2/2] ARM: dts: imx6qdl: Add U-Boot specific device tree files for Cubox-i Walter Lozano
  0 siblings, 1 reply; 8+ messages in thread
From: Walter Lozano @ 2019-10-28 14:00 UTC (permalink / raw)
  To: u-boot

Import SolidRun Cubox-i device tree files from Linux 5.4 to allow the
use of Driver Model and Device Tree.

Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
---
 arch/arm/dts/Makefile                 |   2 +
 arch/arm/dts/imx6dl-cubox-i.dts       |  51 +++++
 arch/arm/dts/imx6q-cubox-i.dts        |  59 ++++++
 arch/arm/dts/imx6qdl-cubox-i.dtsi     | 269 ++++++++++++++++++++++++++
 arch/arm/dts/imx6qdl-sr-som-brcm.dtsi | 144 ++++++++++++++
 arch/arm/dts/imx6qdl-sr-som-emmc.dtsi |  70 +++++++
 arch/arm/dts/imx6qdl-sr-som-ti.dtsi   | 170 ++++++++++++++++
 arch/arm/dts/imx6qdl-sr-som.dtsi      | 121 ++++++++++++
 8 files changed, 886 insertions(+)
 create mode 100644 arch/arm/dts/imx6dl-cubox-i.dts
 create mode 100644 arch/arm/dts/imx6q-cubox-i.dts
 create mode 100644 arch/arm/dts/imx6qdl-cubox-i.dtsi
 create mode 100644 arch/arm/dts/imx6qdl-sr-som-brcm.dtsi
 create mode 100644 arch/arm/dts/imx6qdl-sr-som-emmc.dtsi
 create mode 100644 arch/arm/dts/imx6qdl-sr-som-ti.dtsi
 create mode 100644 arch/arm/dts/imx6qdl-sr-som.dtsi

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 62da168ef8..b37673d6aa 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -560,6 +560,7 @@ dtb-$(CONFIG_MX6Q) += \
 	imx6q-tbs2910.dtb
 
 dtb-$(CONFIG_MX6QDL) += \
+	imx6dl-cubox-i.dtb \
 	imx6dl-dhcom-pdk2.dtb \
 	imx6dl-icore.dtb \
 	imx6dl-icore-mipi.dtb \
@@ -569,6 +570,7 @@ dtb-$(CONFIG_MX6QDL) += \
 	imx6dl-sabresd.dtb \
 	imx6dl-wandboard-revb1.dtb \
 	imx6q-cm-fx6.dtb \
+	imx6q-cubox-i.dtb \
 	imx6q-dhcom-pdk2.dtb \
 	imx6q-icore.dtb \
 	imx6q-icore-mipi.dtb \
diff --git a/arch/arm/dts/imx6dl-cubox-i.dts b/arch/arm/dts/imx6dl-cubox-i.dts
new file mode 100644
index 0000000000..2b1b3e193f
--- /dev/null
+++ b/arch/arm/dts/imx6dl-cubox-i.dts
@@ -0,0 +1,51 @@
+/*
+ * Copyright (C) 2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-brcm.dtsi"
+#include "imx6qdl-cubox-i.dtsi"
+
+/ {
+	model = "SolidRun Cubox-i Solo/DualLite";
+	compatible = "solidrun,cubox-i/dl", "fsl,imx6dl";
+};
diff --git a/arch/arm/dts/imx6q-cubox-i.dts b/arch/arm/dts/imx6q-cubox-i.dts
new file mode 100644
index 0000000000..1c7b262e37
--- /dev/null
+++ b/arch/arm/dts/imx6q-cubox-i.dts
@@ -0,0 +1,59 @@
+/*
+ * Copyright (C) 2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-brcm.dtsi"
+#include "imx6qdl-cubox-i.dtsi"
+
+/ {
+	model = "SolidRun Cubox-i Dual/Quad";
+	compatible = "solidrun,cubox-i/q", "fsl,imx6q";
+};
+
+&sata {
+	status = "okay";
+	fsl,transmit-level-mV = <1104>;
+	fsl,transmit-boost-mdB = <0>;
+	fsl,transmit-atten-16ths = <9>;
+	fsl,no-spread-spectrum;
+};
diff --git a/arch/arm/dts/imx6qdl-cubox-i.dtsi b/arch/arm/dts/imx6qdl-cubox-i.dtsi
new file mode 100644
index 0000000000..e3be453d8a
--- /dev/null
+++ b/arch/arm/dts/imx6qdl-cubox-i.dtsi
@@ -0,0 +1,269 @@
+/*
+ * Copyright (C) 2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	/* Will be filled by the bootloader */
+	memory at 10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0>;
+	};
+
+	ir_recv: ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio3 9 1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cubox_i_ir>;
+	};
+
+	pwmleds {
+		compatible = "pwm-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cubox_i_pwm1>;
+
+		front {
+			active-low;
+			label = "imx6:red:front";
+			max-brightness = <248>;
+			pwms = <&pwm1 0 50000>;
+		};
+	};
+
+	v_5v0: regulator-v-5v0 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "v_5v0";
+	};
+
+	v_usb2: regulator-v-usb2 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cubox_i_usbh1_vbus>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "v_usb2";
+		vin-supply = <&v_5v0>;
+	};
+
+	v_usb1: regulator-v-usb1 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cubox_i_usbotg_vbus>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "v_usb1";
+		vin-supply = <&v_5v0>;
+	};
+
+	sound-spdif {
+		compatible = "fsl,imx-audio-spdif";
+		model = "Integrated SPDIF";
+		/* IMX6 doesn't implement this yet */
+		spdif-controller = <&spdif>;
+		spdif-out;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&pinctrl_gpio_key>;
+		pinctrl-names = "default";
+
+		button_0 {
+			label = "Button 0";
+			gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+	};
+};
+
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cubox_i_hdmi>;
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cubox_i_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cubox_i_i2c3>;
+
+	status = "okay";
+
+	rtc at 68 {
+		compatible = "nxp,pcf8523";
+		reg = <0x68>;
+	};
+};
+
+&iomuxc {
+	cubox_i {
+		pinctrl_cubox_i_hdmi: cubox-i-hdmi {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
+			>;
+		};
+
+		pinctrl_cubox_i_i2c2: cubox-i-i2c2 {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+				MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+			>;
+		};
+
+		pinctrl_cubox_i_i2c3: cubox-i-i2c3 {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
+				MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
+			>;
+		};
+
+		pinctrl_cubox_i_ir: cubox-i-ir {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x80000000
+			>;
+		};
+
+		pinctrl_cubox_i_pwm1: cubox-i-pwm1-front-led {
+			fsl,pins = <MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0>;
+		};
+
+		pinctrl_cubox_i_spdif: cubox-i-spdif {
+			fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
+		};
+
+		pinctrl_cubox_i_usbh1: cubox-i-usbh1 {
+			fsl,pins = <MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0>;
+		};
+
+		pinctrl_cubox_i_usbh1_vbus: cubox-i-usbh1-vbus {
+			fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x4001b0b0>;
+		};
+
+		pinctrl_cubox_i_usbotg: cubox-i-usbotg {
+			/*
+			 * The Cubox-i pulls ID low, but as it's pointless
+			 * leaving it as a pull-up, even if it is just 10uA.
+			 */
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059
+				MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+			>;
+		};
+
+		pinctrl_cubox_i_usbotg_vbus: cubox-i-usbotg-vbus {
+			fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x4001b0b0>;
+		};
+
+		pinctrl_cubox_i_usdhc2_aux: cubox-i-usdhc2-aux {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_4__GPIO1_IO04    0x1f071
+				MX6QDL_PAD_KEY_ROW1__SD2_VSELECT 0x1b071
+			>;
+		};
+
+		pinctrl_cubox_i_usdhc2: cubox-i-usdhc2 {
+			fsl,pins = <
+				MX6QDL_PAD_SD2_CMD__SD2_CMD    0x17059
+				MX6QDL_PAD_SD2_CLK__SD2_CLK    0x10059
+				MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+				MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+				MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+				MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
+			>;
+		};
+
+		pinctrl_gpio_key: gpio-key {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_DA8__GPIO3_IO08	0x17059
+			>;
+		};
+	};
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&spdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cubox_i_spdif>;
+	status = "okay";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cubox_i_usbh1>;
+	vbus-supply = <&v_usb2>;
+	status = "okay";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cubox_i_usbotg>;
+	vbus-supply = <&v_usb1>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cubox_i_usdhc2_aux &pinctrl_cubox_i_usdhc2>;
+	vmmc-supply = <&vcc_3v3>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&vcc_3v3 {
+	vin-supply = <&v_5v0>;
+};
diff --git a/arch/arm/dts/imx6qdl-sr-som-brcm.dtsi b/arch/arm/dts/imx6qdl-sr-som-brcm.dtsi
new file mode 100644
index 0000000000..b55af61dfe
--- /dev/null
+++ b/arch/arm/dts/imx6qdl-sr-som-brcm.dtsi
@@ -0,0 +1,144 @@
+/*
+ * Copyright (C) 2013,2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <dt-bindings/gpio/gpio.h>
+/ {
+	clk_brcm: brcm-clock {
+		compatible = "gpio-gate-clock";
+		#clock-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_microsom_brcm_osc>;
+		enable-gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_brcm: brcm-reg {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 19 0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_microsom_brcm_reg>;
+		regulator-name = "brcm_reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <200000>;
+	};
+
+	usdhc1_pwrseq: usdhc1_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio5 26 GPIO_ACTIVE_LOW>,
+			      <&gpio6 0 GPIO_ACTIVE_LOW>;
+		clocks = <&clk_brcm>;
+		clock-names = "ext_clock";
+	};
+};
+
+&iomuxc {
+	microsom {
+		pinctrl_microsom_brcm_bt: microsom-brcm-bt {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00	0x40013070
+				MX6QDL_PAD_CSI0_DAT15__GPIO6_IO01	0x40013070
+				MX6QDL_PAD_CSI0_DAT18__GPIO6_IO04	0x40013070
+			>;
+		};
+
+		pinctrl_microsom_brcm_osc: microsom-brcm-osc {
+			fsl,pins = <
+				MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05	0x40013070
+			>;
+		};
+
+		pinctrl_microsom_brcm_reg: microsom-brcm-reg {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x40013070
+			>;
+		};
+
+		pinctrl_microsom_brcm_wifi: microsom-brcm-wifi {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_8__XTALOSC_REF_CLK_32K	0x1b0b0
+				MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x40013070
+				MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26	0x40013070
+				MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27	0x40013070
+			>;
+		};
+
+		pinctrl_microsom_uart4: microsom-uart4 {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
+				MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
+				MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
+				MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
+			>;
+		};
+
+		pinctrl_microsom_usdhc1: microsom-usdhc1 {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17059
+				MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10059
+				MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+				MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+				MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+				MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+			>;
+		};
+	};
+};
+
+/* UART4 - Connected to optional BRCM Wifi/BT/FM */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_microsom_brcm_bt &pinctrl_microsom_uart4>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+/* USDHC1 - Connected to optional BRCM Wifi/BT/FM */
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_microsom_brcm_wifi &pinctrl_microsom_usdhc1>;
+	bus-width = <4>;
+	mmc-pwrseq = <&usdhc1_pwrseq>;
+	keep-power-in-suspend;
+	no-1-8-v;
+	non-removable;
+	vmmc-supply = <&reg_brcm>;
+	status = "okay";
+};
diff --git a/arch/arm/dts/imx6qdl-sr-som-emmc.dtsi b/arch/arm/dts/imx6qdl-sr-som-emmc.dtsi
new file mode 100644
index 0000000000..5f3b8baab2
--- /dev/null
+++ b/arch/arm/dts/imx6qdl-sr-som-emmc.dtsi
@@ -0,0 +1,70 @@
+/*
+ * Copyright (C) 2013,2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+&iomuxc {
+	microsom {
+		pinctrl_microsom_usdhc3: microsom-usdhc3 {
+			fsl,pins = <
+				MX6QDL_PAD_SD3_CMD__SD3_CMD    0x17059
+				MX6QDL_PAD_SD3_CLK__SD3_CLK    0x10059
+				MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+				MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+				MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+				MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+				MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
+				MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
+				MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
+				MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
+				MX6QDL_PAD_SD3_RST__SD3_RESET  0x17059
+			>;
+		};
+	};
+};
+
+/* USDHC3 - eMMC */
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_microsom_usdhc3>;
+	bus-width = <8>;
+	non-removable;
+	vmmc-supply = <&vcc_3v3>;
+	status = "okay";
+};
diff --git a/arch/arm/dts/imx6qdl-sr-som-ti.dtsi b/arch/arm/dts/imx6qdl-sr-som-ti.dtsi
new file mode 100644
index 0000000000..44a97ba93a
--- /dev/null
+++ b/arch/arm/dts/imx6qdl-sr-som-ti.dtsi
@@ -0,0 +1,170 @@
+/*
+ * Copyright (C) 2013,2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	nvcc_sd1: regulator-nvcc-sd1 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-name = "nvcc_sd1";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+	};
+
+	clk_ti_wifi: ti-wifi-clock {
+		/* This is a hack around the kernel - using "fixed clock"
+		 * results in the "pinctrl" properties being ignored, and
+		 * the clock not being output.  Instead, use a gated clock
+		 * and the unrouted WL_XTAL_PU gpio.
+		 */
+		compatible = "gpio-gate-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_microsom_ti_clk>;
+		enable-gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;
+	};
+
+	pwrseq_ti_wifi: ti-wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_microsom_ti_wifi_en>;
+		reset-gpios = <&gpio5 26 GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <200>;
+		clocks = <&clk_ti_wifi>;
+		clock-names = "ext_clock";
+	};
+};
+
+&iomuxc {
+	microsom {
+		pinctrl_microsom_ti_bt: microsom-ti-bt {
+			fsl,pins = <
+				/* BT_EN_SOC */
+				MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00	0x40013070
+			>;
+		};
+
+		pinctrl_microsom_ti_clk: microsom-ti-clk {
+			fsl,pins = <
+				/* EXT_32K */
+				MX6QDL_PAD_GPIO_8__XTALOSC_REF_CLK_32K	0x1b0b0
+				/* WL_XTAL_PU (unrouted) */
+				MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x40013070
+			>;
+		};
+
+		pinctrl_microsom_ti_wifi_en: microsom-ti-wifi-en {
+			fsl,pins = <
+				/* WLAN_EN_SOC */
+				MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26	0x40013070
+			>;
+		};
+
+		pinctrl_microsom_ti_wifi_irq: microsom-ti-wifi-irq {
+			fsl,pins = <
+				/* WLAN_IRQ */
+				MX6QDL_PAD_CSI0_DAT18__GPIO6_IO04	0x40013070
+			>;
+		};
+
+		pinctrl_microsom_uart4: microsom-uart4 {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
+				MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
+				MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
+				MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
+			>;
+		};
+
+		pinctrl_microsom_usdhc1: microsom-usdhc1 {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17059
+				MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10059
+				MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+				MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+				MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+				MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+			>;
+		};
+	};
+};
+
+/* UART4 - Connected to optional TI Wi-Fi/BT/FM */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_microsom_uart4>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "ti,wl1837-st";
+		clocks = <&clk_ti_wifi>;
+		clock-names = "ext_clock";
+		enable-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_microsom_ti_bt>;
+	};
+};
+
+/* USDHC1 - Connected to optional TI Wi-Fi/BT/FM */
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_microsom_usdhc1>;
+	bus-width = <4>;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&pwrseq_ti_wifi>;
+	non-removable;
+	vmmc-supply = <&vcc_3v3>;
+	/* vqmmc-supply = <&nvcc_sd1>; - MMC layer doesn't like it! */
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	wlcore at 2 {
+		compatible = "ti,wl1837";
+		reg = <2>;
+		interrupts-extended = <&gpio6 4 IRQ_TYPE_LEVEL_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_microsom_ti_wifi_irq>;
+	};
+};
diff --git a/arch/arm/dts/imx6qdl-sr-som.dtsi b/arch/arm/dts/imx6qdl-sr-som.dtsi
new file mode 100644
index 0000000000..6d7f6b9035
--- /dev/null
+++ b/arch/arm/dts/imx6qdl-sr-som.dtsi
@@ -0,0 +1,121 @@
+/*
+ * Copyright (C) 2013,2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	vcc_3v3: regulator-vcc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-name = "vcc_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
+	phy-mode = "rgmii-id";
+	phy-reset-duration = <2>;
+	phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&iomuxc {
+	microsom {
+		pinctrl_microsom_enet_ar8035: microsom-enet-ar8035 {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b8b0
+				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+				/* AR8035 reset */
+				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x130b0
+				/* AR8035 interrupt */
+				MX6QDL_PAD_DI0_PIN2__GPIO4_IO18		0x1b0b0
+				/* GPIO16 -> AR8035 25MHz */
+				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0b0
+				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x13030
+				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+				/* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
+				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x0a0b1
+				/* AR8035 pin strapping: IO voltage: pull up */
+				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+				/* AR8035 pin strapping: PHYADDR#0: pull down */
+				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x13030
+				/* AR8035 pin strapping: PHYADDR#1: pull down */
+				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x13030
+				/* AR8035 pin strapping: MODE#1: pull up */
+				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+				/* AR8035 pin strapping: MODE#3: pull up */
+				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+				/* AR8035 pin strapping: MODE#0: pull down */
+				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x13030
+
+				/*
+				 * As the RMII pins are also connected to RGMII
+				 * so that an AR8030 can be placed, set these
+				 * to high-z with the same pulls as above.
+				 * Use the GPIO settings to avoid changing the
+				 * input select registers.
+				 */
+				MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x03000
+				MX6QDL_PAD_ENET_RXD0__GPIO1_IO27	0x03000
+				MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x03000
+			>;
+		};
+
+		pinctrl_microsom_uart1: microsom-uart1 {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
+				MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
+			>;
+		};
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_microsom_uart1>;
+	status = "okay";
+};
-- 
2.20.1

^ permalink raw reply related	[flat|nested] 8+ messages in thread