* [U-Boot] Cubieboard2 uboot 2016.09.01 not supporting booting from sata @ 2016-12-20 13:41 Robert Moskowitz 2016-12-20 14:14 ` Jagan Teki 0 siblings, 1 reply; 7+ messages in thread From: Robert Moskowitz @ 2016-12-20 13:41 UTC (permalink / raw) To: u-boot Dear listers, It has been over a year since I have built a new system and tried to set up to boot from sata. What I did in the past was to use a small mSD card with only the uboot bin and no partitions. All my partitions for either Fedrora25 or Centos7 are on the sata. I should boot up, the system sees no partitions on the mSD, it scans for other devices, finds the sata and proceeds from there. Something must have changed in the past year. Or else my notes on what to do are incomplete. Can you help? Here is a capture of a boot attempt with F25 on the sata: U-Boot SPL 2016.09.01 (Oct 19 2016 - 13:46:44) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2016.09.01 (Oct 19 2016 - 13:46:44 +0000) Allwinner Technology CPU: Allwinner A20 (SUN7I) Model: Cubietech Cubieboard2 I2C: ready DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 In: serial Out: serial Err: serial SCSI: Target spinup took 0 ms. AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: ncq stag pm led clo only pmp pio slum part ccc apst Net: eth0: ethernet at 01c50000 Hit any key to stop autoboot: 0 ** Invalid partition 1 ** ** Invalid partition 1 ** ** Invalid partition 1 ** => thank you Bob ^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] Cubieboard2 uboot 2016.09.01 not supporting booting from sata 2016-12-20 13:41 [U-Boot] Cubieboard2 uboot 2016.09.01 not supporting booting from sata Robert Moskowitz @ 2016-12-20 14:14 ` Jagan Teki 2016-12-20 14:55 ` Robert Moskowitz 0 siblings, 1 reply; 7+ messages in thread From: Jagan Teki @ 2016-12-20 14:14 UTC (permalink / raw) To: u-boot On Tue, Dec 20, 2016 at 2:41 PM, Robert Moskowitz <rgm@htt-consult.com> wrote: > Dear listers, > > It has been over a year since I have built a new system and tried to set up > to boot from sata. > > What I did in the past was to use a small mSD card with only the uboot bin > and no partitions. > > All my partitions for either Fedrora25 or Centos7 are on the sata. I should > boot up, the system sees no partitions on the mSD, it scans for other > devices, finds the sata and proceeds from there. > > Something must have changed in the past year. Or else my notes on what to > do are incomplete. > > Can you help? Here is a capture of a boot attempt with F25 on the sata: > > > U-Boot SPL 2016.09.01 (Oct 19 2016 - 13:46:44) > DRAM: 1024 MiB > CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 > Trying to boot from MMC1 > > > U-Boot 2016.09.01 (Oct 19 2016 - 13:46:44 +0000) Allwinner Technology > > CPU: Allwinner A20 (SUN7I) > Model: Cubietech Cubieboard2 > I2C: ready > DRAM: 1 GiB > MMC: SUNXI SD/MMC: 0 > In: serial > Out: serial > Err: serial > SCSI: Target spinup took 0 ms. > AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode > flags: ncq stag pm led clo only pmp pio slum part ccc apst > Net: eth0: ethernet at 01c50000 > Hit any key to stop autoboot: 0 > ** Invalid partition 1 ** > ** Invalid partition 1 ** > ** Invalid partition 1 ** > => try latest master and also please give some more command log, sata part or similar thanks! -- Jagan Teki Free Software Engineer | www.openedev.com U-Boot, Linux | Upstream Maintainer Hyderabad, India. ^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] Cubieboard2 uboot 2016.09.01 not supporting booting from sata 2016-12-20 14:14 ` Jagan Teki @ 2016-12-20 14:55 ` Robert Moskowitz 2016-12-20 14:58 ` Jagan Teki 0 siblings, 1 reply; 7+ messages in thread From: Robert Moskowitz @ 2016-12-20 14:55 UTC (permalink / raw) To: u-boot On 12/20/2016 09:14 AM, Jagan Teki wrote: > On Tue, Dec 20, 2016 at 2:41 PM, Robert Moskowitz <rgm@htt-consult.com> wrote: >> Dear listers, >> >> It has been over a year since I have built a new system and tried to set up >> to boot from sata. >> >> What I did in the past was to use a small mSD card with only the uboot bin >> and no partitions. >> >> All my partitions for either Fedrora25 or Centos7 are on the sata. I should >> boot up, the system sees no partitions on the mSD, it scans for other >> devices, finds the sata and proceeds from there. >> >> Something must have changed in the past year. Or else my notes on what to >> do are incomplete. >> >> Can you help? Here is a capture of a boot attempt with F25 on the sata: >> >> >> U-Boot SPL 2016.09.01 (Oct 19 2016 - 13:46:44) >> DRAM: 1024 MiB >> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 >> Trying to boot from MMC1 >> >> >> U-Boot 2016.09.01 (Oct 19 2016 - 13:46:44 +0000) Allwinner Technology >> >> CPU: Allwinner A20 (SUN7I) >> Model: Cubietech Cubieboard2 >> I2C: ready >> DRAM: 1 GiB >> MMC: SUNXI SD/MMC: 0 >> In: serial >> Out: serial >> Err: serial >> SCSI: Target spinup took 0 ms. >> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode >> flags: ncq stag pm led clo only pmp pio slum part ccc apst >> Net: eth0: ethernet at 01c50000 >> Hit any key to stop autoboot: 0 >> ** Invalid partition 1 ** >> ** Invalid partition 1 ** >> ** Invalid partition 1 ** >> => > try latest master and also please give some more command log, sata > part or similar I can not build a uboot; I have to take what is available. Where can I get a newer Cubieboard2 uboot? And that is the sum total output appearing on the console. If there is more to tease out somehow, please tell me. thank you ^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] Cubieboard2 uboot 2016.09.01 not supporting booting from sata 2016-12-20 14:55 ` Robert Moskowitz @ 2016-12-20 14:58 ` Jagan Teki 2016-12-20 15:15 ` Robert Moskowitz 2016-12-20 15:21 ` Robert Moskowitz 0 siblings, 2 replies; 7+ messages in thread From: Jagan Teki @ 2016-12-20 14:58 UTC (permalink / raw) To: u-boot On Tue, Dec 20, 2016 at 3:55 PM, Robert Moskowitz <rgm@htt-consult.com> wrote: > > > On 12/20/2016 09:14 AM, Jagan Teki wrote: >> >> On Tue, Dec 20, 2016 at 2:41 PM, Robert Moskowitz <rgm@htt-consult.com> >> wrote: >>> >>> Dear listers, >>> >>> It has been over a year since I have built a new system and tried to set >>> up >>> to boot from sata. >>> >>> What I did in the past was to use a small mSD card with only the uboot >>> bin >>> and no partitions. >>> >>> All my partitions for either Fedrora25 or Centos7 are on the sata. I >>> should >>> boot up, the system sees no partitions on the mSD, it scans for other >>> devices, finds the sata and proceeds from there. >>> >>> Something must have changed in the past year. Or else my notes on what >>> to >>> do are incomplete. >>> >>> Can you help? Here is a capture of a boot attempt with F25 on the sata: >>> >>> >>> U-Boot SPL 2016.09.01 (Oct 19 2016 - 13:46:44) >>> DRAM: 1024 MiB >>> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 >>> Trying to boot from MMC1 >>> >>> >>> U-Boot 2016.09.01 (Oct 19 2016 - 13:46:44 +0000) Allwinner Technology >>> >>> CPU: Allwinner A20 (SUN7I) >>> Model: Cubietech Cubieboard2 >>> I2C: ready >>> DRAM: 1 GiB >>> MMC: SUNXI SD/MMC: 0 >>> In: serial >>> Out: serial >>> Err: serial >>> SCSI: Target spinup took 0 ms. >>> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode >>> flags: ncq stag pm led clo only pmp pio slum part ccc apst >>> Net: eth0: ethernet at 01c50000 >>> Hit any key to stop autoboot: 0 >>> ** Invalid partition 1 ** >>> ** Invalid partition 1 ** >>> ** Invalid partition 1 ** >>> => >> >> try latest master and also please give some more command log, sata >> part or similar > > > I can not build a uboot; I have to take what is available. Where can I get > a newer Cubieboard2 uboot? Don't understand what do you mean by this, cant' you able to build Cubieboard2_defconfig on latest? thanks! -- Jagan Teki Free Software Engineer | www.openedev.com U-Boot, Linux | Upstream Maintainer Hyderabad, India. ^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] Cubieboard2 uboot 2016.09.01 not supporting booting from sata 2016-12-20 14:58 ` Jagan Teki @ 2016-12-20 15:15 ` Robert Moskowitz 2016-12-20 15:21 ` Robert Moskowitz 1 sibling, 0 replies; 7+ messages in thread From: Robert Moskowitz @ 2016-12-20 15:15 UTC (permalink / raw) To: u-boot On 12/20/2016 09:58 AM, Jagan Teki wrote: > On Tue, Dec 20, 2016 at 3:55 PM, Robert Moskowitz <rgm@htt-consult.com> wrote: >> >> On 12/20/2016 09:14 AM, Jagan Teki wrote: >>> On Tue, Dec 20, 2016 at 2:41 PM, Robert Moskowitz <rgm@htt-consult.com> >>> wrote: >>>> Dear listers, >>>> >>>> It has been over a year since I have built a new system and tried to set >>>> up >>>> to boot from sata. >>>> >>>> What I did in the past was to use a small mSD card with only the uboot >>>> bin >>>> and no partitions. >>>> >>>> All my partitions for either Fedrora25 or Centos7 are on the sata. I >>>> should >>>> boot up, the system sees no partitions on the mSD, it scans for other >>>> devices, finds the sata and proceeds from there. >>>> >>>> Something must have changed in the past year. Or else my notes on what >>>> to >>>> do are incomplete. >>>> >>>> Can you help? Here is a capture of a boot attempt with F25 on the sata: >>>> >>>> >>>> U-Boot SPL 2016.09.01 (Oct 19 2016 - 13:46:44) >>>> DRAM: 1024 MiB >>>> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 >>>> Trying to boot from MMC1 >>>> >>>> >>>> U-Boot 2016.09.01 (Oct 19 2016 - 13:46:44 +0000) Allwinner Technology >>>> >>>> CPU: Allwinner A20 (SUN7I) >>>> Model: Cubietech Cubieboard2 >>>> I2C: ready >>>> DRAM: 1 GiB >>>> MMC: SUNXI SD/MMC: 0 >>>> In: serial >>>> Out: serial >>>> Err: serial >>>> SCSI: Target spinup took 0 ms. >>>> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode >>>> flags: ncq stag pm led clo only pmp pio slum part ccc apst >>>> Net: eth0: ethernet at 01c50000 >>>> Hit any key to stop autoboot: 0 >>>> ** Invalid partition 1 ** >>>> ** Invalid partition 1 ** >>>> ** Invalid partition 1 ** >>>> => >>> try latest master and also please give some more command log, sata >>> part or similar >> >> I can not build a uboot; I have to take what is available. Where can I get >> a newer Cubieboard2 uboot? > Don't understand what do you mean by this, cant' you able to build > Cubieboard2_defconfig on latest? Where is latest held? How do you build a ??_defconfig? I never had built any. I rarely do a build on Linux. I for the most part take other's hard work and put it to work for me. If you can show me a writeup for creating the uboot (URL would help), I can typically follow a set of instructions. These fingers have been pounding keyboards for 50 years, and can still pound a lot more. thanks for any help Bob ^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] Cubieboard2 uboot 2016.09.01 not supporting booting from sata 2016-12-20 14:58 ` Jagan Teki 2016-12-20 15:15 ` Robert Moskowitz @ 2016-12-20 15:21 ` Robert Moskowitz 2016-12-20 16:12 ` [U-Boot] Fixed - " Robert Moskowitz 1 sibling, 1 reply; 7+ messages in thread From: Robert Moskowitz @ 2016-12-20 15:21 UTC (permalink / raw) To: u-boot On 12/20/2016 09:58 AM, Jagan Teki wrote: > On Tue, Dec 20, 2016 at 3:55 PM, Robert Moskowitz <rgm@htt-consult.com> wrote: >> >> On 12/20/2016 09:14 AM, Jagan Teki wrote: >>> On Tue, Dec 20, 2016 at 2:41 PM, Robert Moskowitz <rgm@htt-consult.com> >>> wrote: >>>> Dear listers, >>>> >>>> It has been over a year since I have built a new system and tried to set >>>> up >>>> to boot from sata. >>>> >>>> What I did in the past was to use a small mSD card with only the uboot >>>> bin >>>> and no partitions. >>>> >>>> All my partitions for either Fedrora25 or Centos7 are on the sata. I >>>> should >>>> boot up, the system sees no partitions on the mSD, it scans for other >>>> devices, finds the sata and proceeds from there. >>>> >>>> Something must have changed in the past year. Or else my notes on what >>>> to >>>> do are incomplete. >>>> >>>> Can you help? Here is a capture of a boot attempt with F25 on the sata: >>>> >>>> >>>> U-Boot SPL 2016.09.01 (Oct 19 2016 - 13:46:44) >>>> DRAM: 1024 MiB >>>> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 >>>> Trying to boot from MMC1 >>>> >>>> >>>> U-Boot 2016.09.01 (Oct 19 2016 - 13:46:44 +0000) Allwinner Technology >>>> >>>> CPU: Allwinner A20 (SUN7I) >>>> Model: Cubietech Cubieboard2 >>>> I2C: ready >>>> DRAM: 1 GiB >>>> MMC: SUNXI SD/MMC: 0 >>>> In: serial >>>> Out: serial >>>> Err: serial >>>> SCSI: Target spinup took 0 ms. >>>> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode >>>> flags: ncq stag pm led clo only pmp pio slum part ccc apst >>>> Net: eth0: ethernet at 01c50000 >>>> Hit any key to stop autoboot: 0 >>>> ** Invalid partition 1 ** >>>> ** Invalid partition 1 ** >>>> ** Invalid partition 1 ** >>>> => >>> try latest master and also please give some more command log, sata >>> part or similar >> >> I can not build a uboot; I have to take what is available. Where can I get >> a newer Cubieboard2 uboot? > Don't understand what do you mean by this, cant' you able to build > Cubieboard2_defconfig on latest? I am looking at what uboot the F26 rawhide build has. Should have something together to test shortly. Bob ^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] Fixed - Re: Cubieboard2 uboot 2016.09.01 not supporting booting from sata 2016-12-20 15:21 ` Robert Moskowitz @ 2016-12-20 16:12 ` Robert Moskowitz 0 siblings, 0 replies; 7+ messages in thread From: Robert Moskowitz @ 2016-12-20 16:12 UTC (permalink / raw) To: u-boot uboot on F26 works: U-Boot 2016.11 (Nov 29 2016 - 23:22:13 +0000) Allwinner Technology See end for full console boot log On 12/20/2016 10:21 AM, Robert Moskowitz wrote: > > > On 12/20/2016 09:58 AM, Jagan Teki wrote: >> On Tue, Dec 20, 2016 at 3:55 PM, Robert Moskowitz >> <rgm@htt-consult.com> wrote: >>> >>> On 12/20/2016 09:14 AM, Jagan Teki wrote: >>>> On Tue, Dec 20, 2016 at 2:41 PM, Robert Moskowitz >>>> <rgm@htt-consult.com> >>>> wrote: >>>>> Dear listers, >>>>> >>>>> It has been over a year since I have built a new system and tried >>>>> to set >>>>> up >>>>> to boot from sata. >>>>> >>>>> What I did in the past was to use a small mSD card with only the >>>>> uboot >>>>> bin >>>>> and no partitions. >>>>> >>>>> All my partitions for either Fedrora25 or Centos7 are on the sata. I >>>>> should >>>>> boot up, the system sees no partitions on the mSD, it scans for other >>>>> devices, finds the sata and proceeds from there. >>>>> >>>>> Something must have changed in the past year. Or else my notes on >>>>> what >>>>> to >>>>> do are incomplete. >>>>> >>>>> Can you help? Here is a capture of a boot attempt with F25 on the >>>>> sata: >>>>> >>>>> >>>>> U-Boot SPL 2016.09.01 (Oct 19 2016 - 13:46:44) >>>>> DRAM: 1024 MiB >>>>> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 >>>>> Trying to boot from MMC1 >>>>> >>>>> >>>>> U-Boot 2016.09.01 (Oct 19 2016 - 13:46:44 +0000) Allwinner Technology >>>>> >>>>> CPU: Allwinner A20 (SUN7I) >>>>> Model: Cubietech Cubieboard2 >>>>> I2C: ready >>>>> DRAM: 1 GiB >>>>> MMC: SUNXI SD/MMC: 0 >>>>> In: serial >>>>> Out: serial >>>>> Err: serial >>>>> SCSI: Target spinup took 0 ms. >>>>> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode >>>>> flags: ncq stag pm led clo only pmp pio slum part ccc apst >>>>> Net: eth0: ethernet at 01c50000 >>>>> Hit any key to stop autoboot: 0 >>>>> ** Invalid partition 1 ** >>>>> ** Invalid partition 1 ** >>>>> ** Invalid partition 1 ** >>>>> => >>>> try latest master and also please give some more command log, sata >>>> part or similar >>> >>> I can not build a uboot; I have to take what is available. Where can >>> I get >>> a newer Cubieboard2 uboot? >> Don't understand what do you mean by this, cant' you able to build >> Cubieboard2_defconfig on latest? > > I am looking at what uboot the F26 rawhide build has. Should have > something together to test shortly. > > Bob U-Boot SPL 2016.11 (Nov 29 2016 - 23:22:13) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2016.11 (Nov 29 2016 - 23:22:13 +0000) Allwinner Technology CPU: Allwinner A20 (SUN7I) Model: Cubietech Cubieboard2 I2C: ready DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial SCSI: Target spinup took 0 ms. AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: ncq stag pm led clo only pmp pio slum part ccc apst Net: eth0: ethernet at 01c50000 starting USB... USB0: USB EHCI 1.00 USB1: USB OHCI 1.0 USB2: USB EHCI 1.00 USB3: USB OHCI 1.0 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 2 for devices... 1 USB Device(s) found Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device ** Invalid partition 1 ** scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: FUJITSU MHV2060B Rev: 892C Type: Hard Disk Capacity: 57241.8 MB = 55.9 GB (117231408 x 512) Found 1 device(s). Device 0: (0:0) Vendor: ATA Prod.: FUJITSU MHV2060B Rev: 892C Type: Hard Disk Capacity: 57241.8 MB = 55.9 GB (117231408 x 512) ... is now current device Scanning scsi 0:2... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf 543 bytes read in 29 ms (17.6 KiB/s) Ignoring unknown command: ui Ignoring malformed menu command: autoboot Ignoring malformed menu command: hidden Ignoring unknown command: totaltimeout Fedora-Xfce-armhfp-25-1.3 Boot Options. 1: Fedora-Xfce-armhfp-25-1.3 (4.8.6-300.fc25.armv7hl) Enter choice: 1: Fedora-Xfce-armhfp-25-1.3 (4.8.6-300.fc25.armv7hl) Retrieving file: /initramfs-4.8.6-300.fc25.armv7hl.img 46669921 bytes read in 1283 ms (34.7 MiB/s) Retrieving file: /vmlinuz-4.8.6-300.fc25.armv7hl 5919120 bytes read in 181 ms (31.2 MiB/s) append: console=ttyS0,115200 enforcing=0 ro root=UUID=eca45483-d548-4444-892d-07 54f1d401bc cma=192MB Retrieving file: /dtb-4.8.6-300.fc25.armv7hl/sun7i-a20-cubieboard2.dtb 34197 bytes read in 280 ms (119.1 KiB/s) ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Loading Ramdisk to 4737d000, end 49fff061 ... OK Loading Device Tree to 47371000, end 4737c594 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.8.6-300.fc25.armv7hl (mockbuild at arm04-builder02.a rm.fedoraproject.org) (gcc version 6.2.1 20160916 (Red Hat 6.2.1-2) (GCC) ) #1 S MP Tue Nov 1 14:46:32 UTC 2016 [ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache [ 0.000000] OF: fdt:Machine model: Cubietech Cubieboard2 [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 192 MiB at 0x74000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT [ 0.000000] percpu: Embedded 15 pages/cpu @ef6bd000 s31500 r8192 d21748 u6144 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 260416 [ 0.000000] Kernel command line: console=ttyS0,115200 enforcing=0 ro root=UUI D=eca45483-d548-4444-892d-0754f1d401bc cma=192MB [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) etc.... ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2016-12-20 16:12 UTC | newest] Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2016-12-20 13:41 [U-Boot] Cubieboard2 uboot 2016.09.01 not supporting booting from sata Robert Moskowitz 2016-12-20 14:14 ` Jagan Teki 2016-12-20 14:55 ` Robert Moskowitz 2016-12-20 14:58 ` Jagan Teki 2016-12-20 15:15 ` Robert Moskowitz 2016-12-20 15:21 ` Robert Moskowitz 2016-12-20 16:12 ` [U-Boot] Fixed - " Robert Moskowitz
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.