* ata command timeout
@ 2007-02-19 19:19 auxsvr
2007-02-20 4:07 ` Tejun Heo
0 siblings, 1 reply; 6+ messages in thread
From: auxsvr @ 2007-02-19 19:19 UTC (permalink / raw)
To: linux-kernel
Hello,
I have been running 2.6.18 for two months and the last couple of days these
error messages have appeared in my logs
(sata_promise kernel module, sda:SATA sdb:PATA disks):
ata1: command timeout
Feb 17 22:23:14 linux kernel: ata1: no sense translation for status: 0x40
Feb 17 22:23:14 linux kernel: ata1: translated ATA stat/err 0x40/00 to SCSI
SK/ASC/ASCQ 0xb/00/00
Feb 17 22:23:14 linux kernel: ata1: status=0x40 { DriveReady }
Feb 17 22:23:14 linux kernel: sd 0:0:0:0: SCSI error: return code = 0x08000002
Feb 17 22:23:14 linux kernel: sda: Current: sense key: Aborted Command
Feb 17 22:23:14 linux kernel: Additional sense: No additional sense
information
Feb 17 22:23:14 linux kernel: end_request: I/O error, dev sda, sector
145179585
Feb 17 22:23:14 linux kernel: Buffer I/O error on device sda2, logical block
2787300
Feb 17 22:23:14 linux kernel: lost page write due to I/O error on sda2
and
ata1: command timeout
Feb 19 20:39:31 linux kernel: ata1: no sense translation for status: 0x40
Feb 19 20:39:31 linux kernel: ata1: translated ATA stat/err 0x40/00 to SCSI
SK/ASC/ASCQ 0xb/00/00
Feb 19 20:39:31 linux kernel: ata1: status=0x40 { DriveReady }
Feb 19 20:39:31 linux kernel: sd 0:0:0:0: SCSI error: return code = 0x08000002
Feb 19 20:39:31 linux kernel: sda: Current: sense key: Aborted Command
Feb 19 20:39:31 linux kernel: Additional sense: No additional sense
information
Feb 19 20:39:31 linux kernel: end_request: I/O error, dev sda, sector 89553479
without any other ill-effects that I know of(I did smart tests on the drive;
all passed successfully).
I have read that hddtemp may be the cause of this (I am running version 0.3)
so is there any reason
to worry and prepare for a HDD replacement?
Kind regards.
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: ata command timeout
2007-02-19 19:19 ata command timeout auxsvr
@ 2007-02-20 4:07 ` Tejun Heo
2007-02-20 4:37 ` Marc Marais
2007-02-20 15:18 ` Mark Lord
0 siblings, 2 replies; 6+ messages in thread
From: Tejun Heo @ 2007-02-20 4:07 UTC (permalink / raw)
To: auxsvr; +Cc: linux-kernel
auxsvr@gmail.com wrote:
> Hello,
>
> I have been running 2.6.18 for two months and the last couple of days these
> error messages have appeared in my logs
> (sata_promise kernel module, sda:SATA sdb:PATA disks):
>
> ata1: command timeout
> Feb 17 22:23:14 linux kernel: ata1: no sense translation for status: 0x40
> Feb 17 22:23:14 linux kernel: ata1: translated ATA stat/err 0x40/00 to SCSI
> SK/ASC/ASCQ 0xb/00/00
> Feb 17 22:23:14 linux kernel: ata1: status=0x40 { DriveReady }
> Feb 17 22:23:14 linux kernel: sd 0:0:0:0: SCSI error: return code = 0x08000002
> Feb 17 22:23:14 linux kernel: sda: Current: sense key: Aborted Command
> Feb 17 22:23:14 linux kernel: Additional sense: No additional sense
> information
> Feb 17 22:23:14 linux kernel: end_request: I/O error, dev sda, sector
> 145179585
> Feb 17 22:23:14 linux kernel: Buffer I/O error on device sda2, logical block
> 2787300
> Feb 17 22:23:14 linux kernel: lost page write due to I/O error on sda2
>
> and
>
> ata1: command timeout
> Feb 19 20:39:31 linux kernel: ata1: no sense translation for status: 0x40
> Feb 19 20:39:31 linux kernel: ata1: translated ATA stat/err 0x40/00 to SCSI
> SK/ASC/ASCQ 0xb/00/00
> Feb 19 20:39:31 linux kernel: ata1: status=0x40 { DriveReady }
> Feb 19 20:39:31 linux kernel: sd 0:0:0:0: SCSI error: return code = 0x08000002
> Feb 19 20:39:31 linux kernel: sda: Current: sense key: Aborted Command
> Feb 19 20:39:31 linux kernel: Additional sense: No additional sense
> information
> Feb 19 20:39:31 linux kernel: end_request: I/O error, dev sda, sector 89553479
>
> without any other ill-effects that I know of(I did smart tests on the drive;
> all passed successfully).
> I have read that hddtemp may be the cause of this (I am running version 0.3)
> so is there any reason
> to worry and prepare for a HDD replacement?
Not really. If the problem occurs very infrequently, you don't need to
worry about it too much. Command timeouts do occur on otherwise healthy
systems from time to time.
--
tejun
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: ata command timeout
2007-02-20 4:07 ` Tejun Heo
@ 2007-02-20 4:37 ` Marc Marais
2007-02-20 15:18 ` Mark Lord
1 sibling, 0 replies; 6+ messages in thread
From: Marc Marais @ 2007-02-20 4:37 UTC (permalink / raw)
To: Tejun Heo, auxsvr; +Cc: linux-kernel
On Tue, 20 Feb 2007 13:07:50 +0900, Tejun Heo wrote
> auxsvr@gmail.com wrote:
> > Hello,
> >
> > I have been running 2.6.18 for two months and the last couple of days these
> > error messages have appeared in my logs
> > (sata_promise kernel module, sda:SATA sdb:PATA disks):
> >
> > ata1: command timeout
> > Feb 17 22:23:14 linux kernel: ata1: no sense translation for status: 0x40
> > Feb 17 22:23:14 linux kernel: ata1: translated ATA stat/err 0x40/00 to SCSI
> > SK/ASC/ASCQ 0xb/00/00
> > Feb 17 22:23:14 linux kernel: ata1: status=0x40 { DriveReady }
> > Feb 17 22:23:14 linux kernel: sd 0:0:0:0: SCSI error: return code = 0x08000002
> > Feb 17 22:23:14 linux kernel: sda: Current: sense key: Aborted Command
> > Feb 17 22:23:14 linux kernel: Additional sense: No additional sense
> > information
> > Feb 17 22:23:14 linux kernel: end_request: I/O error, dev sda, sector
> > 145179585
> > Feb 17 22:23:14 linux kernel: Buffer I/O error on device sda2, logical block
> > 2787300
> > Feb 17 22:23:14 linux kernel: lost page write due to I/O error on sda2
> >
> > and
> >
> > ata1: command timeout
> > Feb 19 20:39:31 linux kernel: ata1: no sense translation for status: 0x40
> > Feb 19 20:39:31 linux kernel: ata1: translated ATA stat/err 0x40/00 to SCSI
> > SK/ASC/ASCQ 0xb/00/00
> > Feb 19 20:39:31 linux kernel: ata1: status=0x40 { DriveReady }
> > Feb 19 20:39:31 linux kernel: sd 0:0:0:0: SCSI error: return code = 0x08000002
> > Feb 19 20:39:31 linux kernel: sda: Current: sense key: Aborted Command
> > Feb 19 20:39:31 linux kernel: Additional sense: No additional sense
> > information
> > Feb 19 20:39:31 linux kernel: end_request: I/O error, dev sda, sector 89553479
> >
> > without any other ill-effects that I know of(I did smart tests on the drive;
> > all passed successfully).
> > I have read that hddtemp may be the cause of this (I am running version 0.3)
> > so is there any reason
> > to worry and prepare for a HDD replacement?
>
> Not really. If the problem occurs very infrequently, you don't need
> to worry about it too much. Command timeouts do occur on otherwise healthy
> systems from time to time.
>
> --
> tejun
> -
I'm experiencing the exact same problem with my setup also with sata_promise.
I have posted to the linux-ide list but it wasn't really acknowledged as a
problem in the driver. Are these command timeouts? The log entry doesn't seem
to say that - just an error with 'DriveReady' and command aborted. I would
think some kind of retry should be performed (and if it is then logged too).
The errors may be benign but the problem is when using software raid (md
driver) that this error may cause a degraded array and worse a damaged array
should a read error like this occur when an array is already degraded.
The question is what happens after the error is reported, is the operation
retried? In my situation the md layer receives the error and recovers by
taking the data from another drive in the array.
The fact that you are also experiencing this means it might be an issue that
needs further investigation in my opinion.
Regards,
Marc
--
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: ata command timeout
2007-02-20 4:07 ` Tejun Heo
2007-02-20 4:37 ` Marc Marais
@ 2007-02-20 15:18 ` Mark Lord
2007-02-20 15:37 ` Jeff Garzik
1 sibling, 1 reply; 6+ messages in thread
From: Mark Lord @ 2007-02-20 15:18 UTC (permalink / raw)
To: Tejun Heo; +Cc: auxsvr, linux-kernel
Tejun Heo wrote:
> auxsvr@gmail.com wrote:
..
>> ata1: command timeout
>> Feb 19 20:39:31 linux kernel: ata1: no sense translation for status: 0x40
>> Feb 19 20:39:31 linux kernel: ata1: translated ATA stat/err 0x40/00 to SCSI
>> SK/ASC/ASCQ 0xb/00/00
>> Feb 19 20:39:31 linux kernel: ata1: status=0x40 { DriveReady }
>> Feb 19 20:39:31 linux kernel: sd 0:0:0:0: SCSI error: return code = 0x08000002
>> Feb 19 20:39:31 linux kernel: sda: Current: sense key: Aborted Command
>> Feb 19 20:39:31 linux kernel: Additional sense: No additional sense
>> information
>> Feb 19 20:39:31 linux kernel: end_request: I/O error, dev sda, sector 89553479
>>
>> without any other ill-effects that I know of(I did smart tests on the drive;
>> all passed successfully).
>> I have read that hddtemp may be the cause of this (I am running version 0.3)
>> so is there any reason
>> to worry and prepare for a HDD replacement?
>
> Not really. If the problem occurs very infrequently, you don't need to
> worry about it too much. Command timeouts do occur on otherwise healthy
> systems from time to time.
I don't believe that. Command timeouts never happen on healthy systems,
unless we have a driver bug. Okay, so I can imagine a pathological case
of a full queue (NCQ) with all 32 commands taking longer than usual due
to ECC retries in the firmware..
But in real life, on a desktop, timeouts never happen as a normal event.
I wonder what's *really* wrong here?
Cheers
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: ata command timeout
2007-02-20 15:18 ` Mark Lord
@ 2007-02-20 15:37 ` Jeff Garzik
2007-02-21 7:03 ` Tejun Heo
0 siblings, 1 reply; 6+ messages in thread
From: Jeff Garzik @ 2007-02-20 15:37 UTC (permalink / raw)
To: Mark Lord; +Cc: Tejun Heo, auxsvr, linux-kernel
Mark Lord wrote:
> I don't believe that. Command timeouts never happen on healthy systems,
> unless we have a driver bug. Okay, so I can imagine a pathological case
> of a full queue (NCQ) with all 32 commands taking longer than usual due
> to ECC retries in the firmware..
It's not quite so black and white. There have definitely been interrupt
delivery problems that cause command timeouts. Also, Intel PIIX BMDMA
(all standard PCI IDE, I think?) is defined to /not/ send an interrupt,
when a DMA error occurs. The driver is instructed to time out the
transaction, and start recovery by deducing the state of things from the
DMA status bits.
Nonetheless, I mostly agree with your statement. The two most common
causes of timeouts that I see are interrupt delivery problems, and
driver bugs.
Jeff
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: ata command timeout
2007-02-20 15:37 ` Jeff Garzik
@ 2007-02-21 7:03 ` Tejun Heo
0 siblings, 0 replies; 6+ messages in thread
From: Tejun Heo @ 2007-02-21 7:03 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Mark Lord, auxsvr, linux-kernel
Jeff Garzik wrote:
> Mark Lord wrote:
>> I don't believe that. Command timeouts never happen on healthy systems,
>> unless we have a driver bug. Okay, so I can imagine a pathological case
>> of a full queue (NCQ) with all 32 commands taking longer than usual due
>> to ECC retries in the firmware..
>
> It's not quite so black and white. There have definitely been interrupt
> delivery problems that cause command timeouts. Also, Intel PIIX BMDMA
> (all standard PCI IDE, I think?) is defined to /not/ send an interrupt,
> when a DMA error occurs. The driver is instructed to time out the
> transaction, and start recovery by deducing the state of things from the
> DMA status bits.
>
> Nonetheless, I mostly agree with your statement. The two most common
> causes of timeouts that I see are interrupt delivery problems, and
> driver bugs.
Oh.. well. My experience is that it's much more common on SATA compared
to PATA. SATA link seems to be one of the most vulnerable parts to
interference. When PSU has the slightest of problem, SATA drives
timeout or give transmission problems. System often survives brief
fluctuation in power input (e.g. when the compressor starts up) but SATA
link sometimes reports error after such event.
Or just buy a static generator and apply it to your computer case.
Generally system is perfectly okay with that but the SATA devices tend
to complain or timeout.
Those condition might not be considered too healthy in any server
environment but they do occur on cheap desktop environment. I mean, a
lot of people are putting 10USD PSU into their desktop machines.
So, yeah, it might be a driver or other problem but if problem is very
intermittent, I tend to lean toward transient hardware problem and
that's primarily why I wanna make EH kick in and recover faster.
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2007-02-21 7:03 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2007-02-19 19:19 ata command timeout auxsvr
2007-02-20 4:07 ` Tejun Heo
2007-02-20 4:37 ` Marc Marais
2007-02-20 15:18 ` Mark Lord
2007-02-20 15:37 ` Jeff Garzik
2007-02-21 7:03 ` Tejun Heo
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.