* [U-Boot-Users] "6.at91rm9200":(1 of 1) [PATCH][ARM] Initialize at91rm9200 board (and set LED)
@ 2007-03-27 16:16 Ulf Samuelsson
0 siblings, 0 replies; only message in thread
From: Ulf Samuelsson @ 2007-03-27 16:16 UTC (permalink / raw)
To: u-boot
Author: Ulf Samuelsson <ulf@atmel.com>
Date: 2007-03-27
Subject: "6.at91rm9200":(1 of 1) [PATCH][ARM] Initialize at91rm9200 board (and set LED)
CHANGELOG:
[PATCH][ARM] Initialize at91rm9200 board (and set LED)
Boot at91rm9200 from parallel flash if CONFIG_BOOTBINFUNC is set
Define some constants needed to use at91rm9200dk/ek LEDs
Add initialization similar to Atmel boot.bin
Make sure things initialized by dataflashboot.bin
does not get initialized again in u-boot
Patch generated from files:
cpu_arm920t_start.S.patch
include_asm-arm_arch-at91rm9200_AT91RM9200.h.patch
Signed-off-by: Ulf Samuelsson
---------------------------------------------------------------------------------------------------------------------------------
diff -urN u-boot-1.2.0/cpu/arm920t/start.S u-boot-1.2.0-atmel/cpu/arm920t/start.S
--- u-boot-1.2.0/cpu/arm920t/start.S 2007-01-07 00:13:11.000000000 +0100
+++ u-boot-1.2.0-atmel/cpu/arm920t/start.S 2007-03-24 20:07:32.000000000 +0100
@@ -27,7 +27,9 @@
#include <config.h>
#include <version.h>
-
+#if defined(CONFIG_AT91RM9200DK) || defined(CONFIG_AT91RM9200EK) || defined(CONFIG_AT91RM9200DF)
+#include <led.h>
+#endif
/*
*************************************************************************
@@ -116,6 +118,68 @@
orr r0,r0,#0xd3
msr cpsr,r0
+#if CONFIG_AT91RM9200
+#if defined(CONFIG_AT91RM9200DK) || defined(CONFIG_AT91RM9200EK) || defined(CONFIG_AT91RM9200DF)
+ bl LED_init
+ bl red_LED_on
+#endif
+
+#ifdef CONFIG_BOOTBINFUNC
+/* code based on entry.S from ATMEL */
+#define AT91C_BASE_CKGR 0xFFFFFC20
+#define CKGR_MOR 0
+ /* Get the CKGR Base Address */
+ ldr r1, =AT91C_BASE_CKGR
+
+/* Main oscillator Enable register APMC_MOR : Enable main oscillator , OSCOUNT = 0xFF */
+/* ldr r0, = AT91C_CKGR_MOSCEN:OR:AT91C_CKGR_OSCOUNT */
+ ldr r0, =0x0000FF01
+ str r0, [r1, #CKGR_MOR]
+ /* Add loop to compensate Main Oscillator startup time */
+ ldr r0, =0x00000010
+LoopOsc:
+ subs r0, r0, #1
+ bhi LoopOsc
+ /* scratch stack */
+ ldr r1, =0x00204000
+ /* Insure word alignment */
+ bic r1, r1, #3
+ /* Init stack SYS */
+ mov sp, r1
+ /*
+ * This does a lot more than just set up the memory, which
+ * is why it's called lowlevelinit
+ */
+ bl lowlevelinit /* in memsetup.S */
+ bl icache_enable;
+ /*------------------------------------
+ Read/modify/write CP15 control register
+ -------------------------------------
+ read cp15 control register (cp15 r1) in r0
+ ------------------------------------*/
+ mrc p15, 0, r0, c1, c0, 0
+ /* Reset bit :Little Endian end fast bus mode */
+ ldr r3, =0xC0000080
+ /* Set bit :Asynchronous clock mode, Not Fast Bus */
+ ldr r4, =0xC0000000
+ bic r0, r0, r3
+ orr r0, r0, r4
+ /* write r0 in cp15 control register (cp15 r1) */
+ mcr p15, 0, r0, c1, c0, 0
+#endif /* CONFIG_BOOTBINFUNC */
+ /*
+ * relocate exeception table
+ */
+ ldr r0, =_start
+ ldr r1, =0x0
+ mov r2, #16
+copyex:
+ subs r2, r2, #1
+ ldr r3, [r0], #4
+ str r3, [r1], #4
+ bne copyex
+#endif
+
/* turn off the watchdog */
#if defined(CONFIG_S3C2400)
# define pWTCON 0x15300000
@@ -160,6 +224,26 @@
bl cpu_init_crit
#endif
+#ifdef CONFIG_AT91RM9200
+#ifdef CONFIG_BOOTBINFUNC
+relocate: /* relocate U-Boot to RAM */
+ adr r0, _start /* r0 <- current position of code */
+ ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
+ cmp r0, r1 /* don't reloc during debug */
+ beq stack_setup
+
+ ldr r2, _armboot_start
+ ldr r3, _bss_start
+ sub r2, r3, r2 /* r2 <- size of armboot */
+ add r2, r0, r2 /* r2 <- source end address */
+
+copy_loop:
+ ldmia r0!, {r3-r10} /* copy from source address [r0] */
+ stmia r1!, {r3-r10} /* copy to target address [r1] */
+ cmp r0, r2 /* until source end addreee [r2] */
+ ble copy_loop
+#endif /* CONFIG_BOOTBINFUNC */
+#else
#ifndef CONFIG_SKIP_RELOCATE_UBOOT
relocate: /* relocate U-Boot to RAM */
adr r0, _start /* r0 <- current position of code */
@@ -178,7 +262,7 @@
cmp r0, r2 /* until source end addreee [r2] */
ble copy_loop
#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
-
+#endif
/* Set up the stack */
stack_setup:
ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
@@ -262,7 +346,11 @@
* find a lowlevel_init.S in your board directory.
*/
mov ip, lr
- bl lowlevel_init
+#if defined(CONFIG_AT91RM9200DK) || defined(CONFIG_AT91RM9200EK) || defined(CONFIG_AT91RM9200DF)
+
+#else
+ bl lowlevel_init
+#endif
mov lr, ip
mov pc, lr
#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
diff -urN u-boot-1.2.0/include/asm-arm/arch-at91rm9200/AT91RM9200.h u-boot-1.2.0-atmel/include/asm-arm/arch-at91rm9200/AT91RM9200.h
--- u-boot-1.2.0/include/asm-arm/arch-at91rm9200/AT91RM9200.h 2007-01-07 00:13:11.000000000 +0100
+++ u-boot-1.2.0-atmel/include/asm-arm/arch-at91rm9200/AT91RM9200.h 2007-03-24 20:07:32.000000000 +0100
@@ -692,11 +692,15 @@
#define AT91C_PIO_PA7 ((unsigned int) 1 << 7) /* Pin Controlled by PA7 */
#define AT91C_PA7_ETXCK_EREFCK ((unsigned int) AT91C_PIO_PA7) /* Ethernet MAC Transmit Clock/Reference Clock */
+#define AT91C_PIO_PB0 ((unsigned int) 1 << 0) /* Pin Controlled by PB3 */
+#define AT91C_PIO_PB1 ((unsigned int) 1 << 1) /* Pin Controlled by PB3 */
+#define AT91C_PIO_PB2 ((unsigned int) 1 << 2) /* Pin Controlled by PB3 */
#define AT91C_PIO_PB3 ((unsigned int) 1 << 3) /* Pin Controlled by PB3 */
#define AT91C_PIO_PB4 ((unsigned int) 1 << 4) /* Pin Controlled by PB4 */
#define AT91C_PIO_PB5 ((unsigned int) 1 << 5) /* Pin Controlled by PB5 */
#define AT91C_PIO_PB6 ((unsigned int) 1 << 6) /* Pin Controlled by PB6 */
#define AT91C_PIO_PB7 ((unsigned int) 1 << 7) /* Pin Controlled by PB7 */
+#define AT91C_PIO_PB22 ((unsigned int) 1 << 22) /* Pin Controlled by PB22 */
#define AT91C_PIO_PB25 ((unsigned int) 1 << 25) /* Pin Controlled by PB25 */
#define AT91C_PB25_DSR1 ((unsigned int) AT91C_PIO_PB25) /* USART 1 Data Set ready */
#define AT91C_PB25_EF100 ((unsigned int) AT91C_PIO_PB25) /* Ethernet MAC Force 100 Mbits */
@@ -737,19 +741,36 @@
#define AT91C_PIOC_CODR ((AT91_REG *) 0xFFFFF834) /* (PIOC) Clear Output Data Register */
#define AT91C_PIOC_PDSR ((AT91_REG *) 0xFFFFF83C) /* (PIOC) Pin Data Status Register */
-#define AT91C_BASE_SPI ((AT91PS_SPI) 0xFFFE0000) /* (SPI) Base Address */
-#define AT91C_BASE_EMAC ((AT91PS_EMAC) 0xFFFBC000) /* (EMAC) Base Address */
+#define AT91C_BASE_AIC ((AT91PS_AIC) 0xFFFFF000) /* (AIC) Base Address */
+#define AT91C_BASE_DBGU ((AT91PS_DBGU) 0xFFFFF200) /* (DBGU) Base Address */
+#define AT91C_BASE_PIOA ((AT91PS_PIO) 0xFFFFF400) /* (PIOA) Base Address */
+#define AT91C_BASE_PIOB ((AT91PS_PIO) 0xFFFFF600) /* (PIOB) Base Address */
+#define AT91C_BASE_PIOC ((AT91PS_PIO) 0xFFFFF800) /* (PIOC) Base Address */
+#define AT91C_BASE_PIOD ((AT91PS_PIO) 0xFFFFFA00) /* (PIOC) Base Address */
#define AT91C_BASE_PMC ((AT91PS_PMC) 0xFFFFFC00) /* (PMC) Base Address */
+#if 0
+#define AT91C_BASE_ST ((AT91PS_ST) 0xFFFFFD00) /* (PMC) Base Address */
+#define AT91C_BASE_RTC ((AT91PS_RTC) 0xFFFFFE00) /* (PMC) Base Address */
+#define AT91C_BASE_MC ((AT91PS_MC) 0xFFFFFF00) /* (PMC) Base Address */
+#endif
+
#define AT91C_BASE_TC0 ((AT91PS_TC) 0xFFFA0000) /* (TC0) Base Address */
-#define AT91C_BASE_DBGU ((AT91PS_DBGU) 0xFFFFF200) /* (DBGU) Base Address */
+#define AT91C_BASE_TC1 ((AT91PS_TC) 0xFFFA4000) /* (TC0) Base Address */
+#if 0
+#define AT91C_BASE_UDP ((AT91PS_UDP) 0xFFFB0000) /* (TC0) Base Address */
+#define AT91C_BASE_MCI ((AT91PS_MCI) 0xFFFB4000) /* (TC0) Base Address */
+#define AT91C_BASE_TWI ((AT91PS_TWI) 0xFFFB8000) /* (TC0) Base Address */
+#endif
+#define AT91C_BASE_EMAC ((AT91PS_EMAC) 0xFFFBC000) /* (EMAC) Base Address */
+#define AT91C_BASE_US0 ((AT91PS_USART) 0xFFFC0000) /* (US0) Base Address */
+#define AT91C_BASE_US1 ((AT91PS_USART) 0xFFFC4000) /* (US1) Base Address */
+#define AT91C_BASE_US2 ((AT91PS_USART) 0xFFFC8000) /* (US1) Base Address */
+#define AT91C_BASE_US3 ((AT91PS_USART) 0xFFFCC000) /* (US1) Base Address */
+#define AT91C_BASE_SPI ((AT91PS_SPI) 0xFFFE0000) /* (SPI) Base Address */
+
#define AT91C_BASE_CKGR ((AT91PS_CKGR) 0xFFFFFC20) /* (CKGR) Base Address */
-#define AT91C_BASE_PIOC ((AT91PS_PIO) 0xFFFFF800) /* (PIOC) Base Address */
-#define AT91C_BASE_PIOB ((AT91PS_PIO) 0xFFFFF600) /* (PIOB) Base Address */
-#define AT91C_BASE_PIOA ((AT91PS_PIO) 0xFFFFF400) /* (PIOA) Base Address */
#define AT91C_EBI_CSA ((AT91_REG *) 0xFFFFFF60) /* (EBI) Chip Select Assignment Register */
#define AT91C_BASE_SMC2 ((AT91PS_SMC2) 0xFFFFFF70) /* (SMC2) Base Address */
-#define AT91C_BASE_US0 ((AT91PS_USART) 0xFFFC0000) /* (US0) Base Address */
-#define AT91C_BASE_US1 ((AT91PS_USART) 0xFFFC4000) /* (US1) Base Address */
#define AT91C_TCB0_BMR ((AT91_REG *) 0xFFFA00C4) /* (TCB0) TC Block Mode Register */
#define AT91C_TCB0_BCR ((AT91_REG *) 0xFFFA00C0) /* (TCB0) TC Block Control Register */
#define AT91C_PIOC_PDR ((AT91_REG *) 0xFFFFF804) /* (PIOC) PIO Disable Register */
--
Best Regards,
Ulf Samuelsson
-------------- next part --------------
A non-text attachment was scrubbed...
Name: ulf.vcf
Type: text/x-vcard
Size: 301 bytes
Desc: not available
Url : http://lists.denx.de/pipermail/u-boot/attachments/20070327/05368e7a/attachment.vcf
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2007-03-27 16:16 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2007-03-27 16:16 [U-Boot-Users] "6.at91rm9200":(1 of 1) [PATCH][ARM] Initialize at91rm9200 board (and set LED) Ulf Samuelsson
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.