* [PATCH 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias
@ 2022-08-08 23:47 Rudraksha Gupta
2022-08-08 23:47 ` [PATCH 2/2] ARM: msm8960: Add Samsung Galaxy Express support Rudraksha Gupta
2022-08-09 5:30 ` [PATCH " Krzysztof Kozlowski
0 siblings, 2 replies; 13+ messages in thread
From: Rudraksha Gupta @ 2022-08-08 23:47 UTC (permalink / raw)
To: krzysztof.kozlowski+dt
Cc: agross, bjorn.andersson, david, devicetree, linux-arm-msm,
linux-kernel, robh+dt, Rudraksha Gupta
This patch renames cxo_board to be up to date with the current naming
style. It also adds an alias
Signed-off-by: Rudraksha Gupta <guptarud@gmail.com>
---
arch/arm/boot/dts/Makefile | 1 +
drivers/clk/qcom/gcc-msm8960.c | 2 +-
2 files changed, 2 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 05d8aef6e5d2..d55f196ad733 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1049,6 +1049,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-msm8660-surf.dtb \
qcom-msm8916-samsung-serranove.dtb \
qcom-msm8960-cdp.dtb \
+ qcom-msm8960-samsung-expressatt.dtb \
qcom-msm8974-lge-nexus5-hammerhead.dtb \
qcom-msm8974-sony-xperia-rhine-amami.dtb \
qcom-msm8974-sony-xperia-rhine-honami.dtb \
diff --git a/drivers/clk/qcom/gcc-msm8960.c b/drivers/clk/qcom/gcc-msm8960.c
index 051745ef99c8..56ce05a846dd 100644
--- a/drivers/clk/qcom/gcc-msm8960.c
+++ b/drivers/clk/qcom/gcc-msm8960.c
@@ -3624,7 +3624,7 @@ static int gcc_msm8960_probe(struct platform_device *pdev)
if (!match)
return -EINVAL;
- ret = qcom_cc_register_board_clk(dev, "cxo_board", "cxo", 19200000);
+ ret = qcom_cc_register_board_clk(dev, "cxo-board", "cxo", 19200000);
if (ret)
return ret;
--
2.25.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH 2/2] ARM: msm8960: Add Samsung Galaxy Express support
2022-08-08 23:47 [PATCH 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias Rudraksha Gupta
@ 2022-08-08 23:47 ` Rudraksha Gupta
2022-08-09 0:02 ` [PATCH v2 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias Rudraksha Gupta
2022-08-09 5:30 ` [PATCH " Krzysztof Kozlowski
1 sibling, 1 reply; 13+ messages in thread
From: Rudraksha Gupta @ 2022-08-08 23:47 UTC (permalink / raw)
To: krzysztof.kozlowski+dt
Cc: agross, bjorn.andersson, david, devicetree, linux-arm-msm,
linux-kernel, robh+dt, Rudraksha Gupta
This adds a very basic device tree file for the Samsung Galaxy Express
SGH-I437. Currently, the following things work: UART, eMMC, SD Card, and
USB.
Signed-off-by: Rudraksha Gupta <guptarud@gmail.com>
---
.../dts/qcom-msm8960-samsung-expressatt.dts | 337 ++++++++++++++++++
arch/arm/boot/dts/qcom-msm8960.dtsi | 2 +-
2 files changed, 338 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts
diff --git a/arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts b/arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts
new file mode 100644
index 000000000000..cf557f0c9a59
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts
@@ -0,0 +1,337 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include <dt-bindings/input/input.h>
+#include "qcom-msm8960.dtsi"
+
+/ {
+ model = "Samsung Galaxy S3 SGH-I437";
+ compatible = "samsung,expressatt", "qcom,msm8960";
+
+ aliases {
+ serial0 = &gsbi5_serial;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ };
+
+ soc {
+ gsbi@16400000 {
+ status = "ok";
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ serial@16440000 {
+ status = "ok";
+ };
+ };
+
+ amba {
+ /* eMMC */
+ sdcc1: mmc@12400000 {
+ status = "okay";
+ vmmc-supply = <&pm8921_l5>;
+ };
+
+ /* External micro SD card */
+ sdcc3: mmc@12180000 {
+ status = "okay";
+ vmmc-supply = <&pm8921_l6>;
+ vqmmc-supply = <&pm8921_l7>;
+ };
+ };
+
+ rpm@108000 {
+ regulators {
+ compatible = "qcom,rpm-pm8921-regulators";
+ vin_lvs1_3_6-supply = <&pm8921_s4>;
+ vin_lvs2-supply = <&pm8921_s4>;
+ vin_lvs4_5_7-supply = <&pm8921_s4>;
+ vdd_ncp-supply = <&pm8921_l6>;
+ vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+ vdd_l21_l23_l29-supply = <&pm8921_s8>;
+ vdd_l24-supply = <&pm8921_s1>;
+ vdd_l25-supply = <&pm8921_s1>;
+ vdd_l27-supply = <&pm8921_s7>;
+ vdd_l28-supply = <&pm8921_s7>;
+
+ /* Buck SMPS */
+ pm8921_s1: s1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ };
+
+ pm8921_s2: s2 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+
+ pm8921_s3: s3 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1150000>;
+ qcom,switch-mode-frequency = <4800000>;
+ bias-pull-down;
+ };
+
+ pm8921_s4: s4 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+ };
+
+ pm8921_s7: s7 {
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ };
+
+ pm8921_s8: s8 {
+ regulator-always-on;
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+
+ /* PMOS LDO */
+ pm8921_l1: l1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ bias-pull-down;
+ };
+
+ pm8921_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+
+ pm8921_l3: l3 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+
+ pm8921_l4: l4 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ pm8921_l5: l5 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l6: l6 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l7: l7 {
+ regulator-always-on;
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l8: l8 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3100000>;
+ bias-pull-down;
+ };
+
+ pm8921_l9: l9 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ bias-pull-down;
+ };
+
+ pm8921_l10: l10 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ bias-pull-down;
+ };
+
+ pm8921_l11: l11 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+
+ pm8921_l12: l12 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+
+ pm8921_l14: l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ pm8921_l15: l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l16: l16 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+ bias-pull-down;
+ };
+
+ pm8921_l17: l17 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+
+ pm8921_l18: l18 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1500000>;
+ bias-pull-down;
+ };
+
+ pm8921_l21: l21 {
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+ bias-pull-down;
+ };
+
+ pm8921_l22: l22 {
+ regulator-min-microvolt = <2750000>;
+ regulator-max-microvolt = <2750000>;
+ bias-pull-down;
+ };
+
+ pm8921_l23: l23 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ pm8921_l24: l24 {
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1150000>;
+ bias-pull-down;
+ };
+
+ pm8921_l25: l25 {
+ regulator-always-on;
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ bias-pull-down;
+ };
+
+ /* Low Voltage Switch */
+ pm8921_lvs1: lvs1 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs2: lvs2 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs3: lvs3 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs4: lvs4 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs5: lvs5 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs6: lvs6 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs7: lvs7 {
+ bias-pull-down;
+ };
+
+ pm8921_ncp: ncp {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <1600000>;
+ };
+ };
+ };
+
+ gsbi@16000000 {
+ status = "ok";
+ qcom,mode = <GSBI_PROT_SPI>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_default>;
+ spi@16080000 {
+ status = "ok";
+ };
+ };
+
+ pinctrl@800000 {
+ spi1_default: spi1_default {
+ mux {
+ pins = "gpio6", "gpio7", "gpio9";
+ function = "gsbi1";
+ };
+
+ mosi {
+ pins = "gpio6";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ miso {
+ pins = "gpio7";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs {
+ pins = "gpio8";
+ drive-strength = <12>;
+ bias-disable;
+ output-low;
+ };
+
+ clk {
+ pins = "gpio9";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+ };
+
+ usb@12500000 {
+ status = "okay";
+ dr_mode = "otg";
+
+ ulpi {
+ phy {
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l4>;
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi
index 0e099aa7c889..2ed969785b78 100644
--- a/arch/arm/boot/dts/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8960.dtsi
@@ -58,7 +58,7 @@ cpu-pmu {
};
clocks {
- cxo_board {
+ cxo_board: cxo-board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <19200000>;
--
2.25.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v2 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias
2022-08-08 23:47 ` [PATCH 2/2] ARM: msm8960: Add Samsung Galaxy Express support Rudraksha Gupta
@ 2022-08-09 0:02 ` Rudraksha Gupta
2022-08-09 0:03 ` [PATCH v2 2/2] ARM: msm8960: Add Samsung Galaxy Express support Rudraksha Gupta
` (2 more replies)
0 siblings, 3 replies; 13+ messages in thread
From: Rudraksha Gupta @ 2022-08-09 0:02 UTC (permalink / raw)
To: guptarud
Cc: agross, bjorn.andersson, david, devicetree,
krzysztof.kozlowski+dt, linux-arm-msm, linux-kernel, robh+dt
This patch renames cxo_board to be up to date with the current naming
style. It also adds an alias.
Signed-off-by: Rudraksha Gupta <guptarud@gmail.com>
---
v2:
- Group the correct changes together
arch/arm/boot/dts/qcom-msm8960.dtsi | 2 +-
drivers/clk/qcom/gcc-msm8960.c | 2 +-
2 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi
index 0e099aa7c889..2ed969785b78 100644
--- a/arch/arm/boot/dts/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8960.dtsi
@@ -58,7 +58,7 @@ cpu-pmu {
};
clocks {
- cxo_board {
+ cxo_board: cxo-board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <19200000>;
diff --git a/drivers/clk/qcom/gcc-msm8960.c b/drivers/clk/qcom/gcc-msm8960.c
index 051745ef99c8..56ce05a846dd 100644
--- a/drivers/clk/qcom/gcc-msm8960.c
+++ b/drivers/clk/qcom/gcc-msm8960.c
@@ -3624,7 +3624,7 @@ static int gcc_msm8960_probe(struct platform_device *pdev)
if (!match)
return -EINVAL;
- ret = qcom_cc_register_board_clk(dev, "cxo_board", "cxo", 19200000);
+ ret = qcom_cc_register_board_clk(dev, "cxo-board", "cxo", 19200000);
if (ret)
return ret;
--
2.25.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v2 2/2] ARM: msm8960: Add Samsung Galaxy Express support
2022-08-09 0:02 ` [PATCH v2 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias Rudraksha Gupta
@ 2022-08-09 0:03 ` Rudraksha Gupta
2022-08-09 5:35 ` Krzysztof Kozlowski
2022-08-09 5:32 ` [PATCH v2 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias Krzysztof Kozlowski
2022-08-10 19:53 ` Bjorn Andersson
2 siblings, 1 reply; 13+ messages in thread
From: Rudraksha Gupta @ 2022-08-09 0:03 UTC (permalink / raw)
To: guptarud
Cc: agross, bjorn.andersson, david, devicetree,
krzysztof.kozlowski+dt, linux-arm-msm, linux-kernel, robh+dt
This adds a very basic device tree file for the Samsung Galaxy Express
SGH-I437. Currently, the following things work: UART, eMMC, SD Card, and
USB.
Signed-off-by: Rudraksha Gupta <guptarud@gmail.com>
---
v2:
- Group the correct changes together
arch/arm/boot/dts/Makefile | 1 +
.../dts/qcom-msm8960-samsung-expressatt.dts | 337 ++++++++++++++++++
2 files changed, 338 insertions(+)
create mode 100644 arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 05d8aef6e5d2..d55f196ad733 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1049,6 +1049,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-msm8660-surf.dtb \
qcom-msm8916-samsung-serranove.dtb \
qcom-msm8960-cdp.dtb \
+ qcom-msm8960-samsung-expressatt.dtb \
qcom-msm8974-lge-nexus5-hammerhead.dtb \
qcom-msm8974-sony-xperia-rhine-amami.dtb \
qcom-msm8974-sony-xperia-rhine-honami.dtb \
diff --git a/arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts b/arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts
new file mode 100644
index 000000000000..cf557f0c9a59
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts
@@ -0,0 +1,337 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include <dt-bindings/input/input.h>
+#include "qcom-msm8960.dtsi"
+
+/ {
+ model = "Samsung Galaxy S3 SGH-I437";
+ compatible = "samsung,expressatt", "qcom,msm8960";
+
+ aliases {
+ serial0 = &gsbi5_serial;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ };
+
+ soc {
+ gsbi@16400000 {
+ status = "ok";
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ serial@16440000 {
+ status = "ok";
+ };
+ };
+
+ amba {
+ /* eMMC */
+ sdcc1: mmc@12400000 {
+ status = "okay";
+ vmmc-supply = <&pm8921_l5>;
+ };
+
+ /* External micro SD card */
+ sdcc3: mmc@12180000 {
+ status = "okay";
+ vmmc-supply = <&pm8921_l6>;
+ vqmmc-supply = <&pm8921_l7>;
+ };
+ };
+
+ rpm@108000 {
+ regulators {
+ compatible = "qcom,rpm-pm8921-regulators";
+ vin_lvs1_3_6-supply = <&pm8921_s4>;
+ vin_lvs2-supply = <&pm8921_s4>;
+ vin_lvs4_5_7-supply = <&pm8921_s4>;
+ vdd_ncp-supply = <&pm8921_l6>;
+ vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+ vdd_l21_l23_l29-supply = <&pm8921_s8>;
+ vdd_l24-supply = <&pm8921_s1>;
+ vdd_l25-supply = <&pm8921_s1>;
+ vdd_l27-supply = <&pm8921_s7>;
+ vdd_l28-supply = <&pm8921_s7>;
+
+ /* Buck SMPS */
+ pm8921_s1: s1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ };
+
+ pm8921_s2: s2 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+
+ pm8921_s3: s3 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1150000>;
+ qcom,switch-mode-frequency = <4800000>;
+ bias-pull-down;
+ };
+
+ pm8921_s4: s4 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+ };
+
+ pm8921_s7: s7 {
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ };
+
+ pm8921_s8: s8 {
+ regulator-always-on;
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+
+ /* PMOS LDO */
+ pm8921_l1: l1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ bias-pull-down;
+ };
+
+ pm8921_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+
+ pm8921_l3: l3 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+
+ pm8921_l4: l4 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ pm8921_l5: l5 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l6: l6 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l7: l7 {
+ regulator-always-on;
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l8: l8 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3100000>;
+ bias-pull-down;
+ };
+
+ pm8921_l9: l9 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ bias-pull-down;
+ };
+
+ pm8921_l10: l10 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ bias-pull-down;
+ };
+
+ pm8921_l11: l11 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+
+ pm8921_l12: l12 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+
+ pm8921_l14: l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ pm8921_l15: l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l16: l16 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+ bias-pull-down;
+ };
+
+ pm8921_l17: l17 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+
+ pm8921_l18: l18 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1500000>;
+ bias-pull-down;
+ };
+
+ pm8921_l21: l21 {
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+ bias-pull-down;
+ };
+
+ pm8921_l22: l22 {
+ regulator-min-microvolt = <2750000>;
+ regulator-max-microvolt = <2750000>;
+ bias-pull-down;
+ };
+
+ pm8921_l23: l23 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ pm8921_l24: l24 {
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1150000>;
+ bias-pull-down;
+ };
+
+ pm8921_l25: l25 {
+ regulator-always-on;
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ bias-pull-down;
+ };
+
+ /* Low Voltage Switch */
+ pm8921_lvs1: lvs1 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs2: lvs2 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs3: lvs3 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs4: lvs4 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs5: lvs5 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs6: lvs6 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs7: lvs7 {
+ bias-pull-down;
+ };
+
+ pm8921_ncp: ncp {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <1600000>;
+ };
+ };
+ };
+
+ gsbi@16000000 {
+ status = "ok";
+ qcom,mode = <GSBI_PROT_SPI>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_default>;
+ spi@16080000 {
+ status = "ok";
+ };
+ };
+
+ pinctrl@800000 {
+ spi1_default: spi1_default {
+ mux {
+ pins = "gpio6", "gpio7", "gpio9";
+ function = "gsbi1";
+ };
+
+ mosi {
+ pins = "gpio6";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ miso {
+ pins = "gpio7";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs {
+ pins = "gpio8";
+ drive-strength = <12>;
+ bias-disable;
+ output-low;
+ };
+
+ clk {
+ pins = "gpio9";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+ };
+
+ usb@12500000 {
+ status = "okay";
+ dr_mode = "otg";
+
+ ulpi {
+ phy {
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l4>;
+ };
+ };
+ };
+ };
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* Re: [PATCH 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias
2022-08-08 23:47 [PATCH 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias Rudraksha Gupta
2022-08-08 23:47 ` [PATCH 2/2] ARM: msm8960: Add Samsung Galaxy Express support Rudraksha Gupta
@ 2022-08-09 5:30 ` Krzysztof Kozlowski
1 sibling, 0 replies; 13+ messages in thread
From: Krzysztof Kozlowski @ 2022-08-09 5:30 UTC (permalink / raw)
To: Rudraksha Gupta, krzysztof.kozlowski+dt
Cc: agross, bjorn.andersson, david, devicetree, linux-arm-msm,
linux-kernel, robh+dt
On 09/08/2022 02:47, Rudraksha Gupta wrote:
> This patch renames cxo_board to be up to date with the current naming
> style. It also adds an alias
Do not use "This commit/patch".
https://elixir.bootlin.com/linux/v5.17.1/source/Documentation/process/submitting-patches.rst#L95
>
> Signed-off-by: Rudraksha Gupta <guptarud@gmail.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> drivers/clk/qcom/gcc-msm8960.c | 2 +-
> 2 files changed, 2 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 05d8aef6e5d2..d55f196ad733 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1049,6 +1049,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
> qcom-msm8660-surf.dtb \
> qcom-msm8916-samsung-serranove.dtb \
> qcom-msm8960-cdp.dtb \
> + qcom-msm8960-samsung-expressatt.dtb \
This does not look related at all.
> qcom-msm8974-lge-nexus5-hammerhead.dtb \
> qcom-msm8974-sony-xperia-rhine-amami.dtb \
> qcom-msm8974-sony-xperia-rhine-honami.dtb \
> diff --git a/drivers/clk/qcom/gcc-msm8960.c b/drivers/clk/qcom/gcc-msm8960.c
> index 051745ef99c8..56ce05a846dd 100644
> --- a/drivers/clk/qcom/gcc-msm8960.c
> +++ b/drivers/clk/qcom/gcc-msm8960.c
> @@ -3624,7 +3624,7 @@ static int gcc_msm8960_probe(struct platform_device *pdev)
> if (!match)
> return -EINVAL;
>
> - ret = qcom_cc_register_board_clk(dev, "cxo_board", "cxo", 19200000);
> + ret = qcom_cc_register_board_clk(dev, "cxo-board", "cxo", 19200000);
... and this does not look related to subject prefix.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v2 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias
2022-08-09 0:02 ` [PATCH v2 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias Rudraksha Gupta
2022-08-09 0:03 ` [PATCH v2 2/2] ARM: msm8960: Add Samsung Galaxy Express support Rudraksha Gupta
@ 2022-08-09 5:32 ` Krzysztof Kozlowski
2022-08-10 19:53 ` Bjorn Andersson
2 siblings, 0 replies; 13+ messages in thread
From: Krzysztof Kozlowski @ 2022-08-09 5:32 UTC (permalink / raw)
To: Rudraksha Gupta
Cc: agross, bjorn.andersson, david, devicetree,
krzysztof.kozlowski+dt, linux-arm-msm, linux-kernel, robh+dt
On 09/08/2022 03:02, Rudraksha Gupta wrote:
> This patch renames cxo_board to be up to date with the current naming
> style. It also adds an alias.
Same comment as v1.
Additionally you do not explain why you are doing it.
>
> Signed-off-by: Rudraksha Gupta <guptarud@gmail.com>
> ---
> v2:
> - Group the correct changes together
Don't link new patchsets to some other threads.
>
> arch/arm/boot/dts/qcom-msm8960.dtsi | 2 +-
> drivers/clk/qcom/gcc-msm8960.c | 2 +-
> 2 files changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi
> index 0e099aa7c889..2ed969785b78 100644
> --- a/arch/arm/boot/dts/qcom-msm8960.dtsi
> +++ b/arch/arm/boot/dts/qcom-msm8960.dtsi
> @@ -58,7 +58,7 @@ cpu-pmu {
> };
>
> clocks {
> - cxo_board {
> + cxo_board: cxo-board {
> compatible = "fixed-clock";
> #clock-cells = <0>;
> clock-frequency = <19200000>;
> diff --git a/drivers/clk/qcom/gcc-msm8960.c b/drivers/clk/qcom/gcc-msm8960.c
> index 051745ef99c8..56ce05a846dd 100644
> --- a/drivers/clk/qcom/gcc-msm8960.c
> +++ b/drivers/clk/qcom/gcc-msm8960.c
> @@ -3624,7 +3624,7 @@ static int gcc_msm8960_probe(struct platform_device *pdev)
> if (!match)
> return -EINVAL;
>
> - ret = qcom_cc_register_board_clk(dev, "cxo_board", "cxo", 19200000);
> + ret = qcom_cc_register_board_clk(dev, "cxo-board", "cxo", 19200000);
My comment from v1 still applies - this does not match subsystem.
Additionally DTS change and driver change *cannot* go together.
Basically your commit is non-bisectable which is indication it is not
correct approach.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v2 2/2] ARM: msm8960: Add Samsung Galaxy Express support
2022-08-09 0:03 ` [PATCH v2 2/2] ARM: msm8960: Add Samsung Galaxy Express support Rudraksha Gupta
@ 2022-08-09 5:35 ` Krzysztof Kozlowski
2022-08-09 23:57 ` Rudraksha Gupta
0 siblings, 1 reply; 13+ messages in thread
From: Krzysztof Kozlowski @ 2022-08-09 5:35 UTC (permalink / raw)
To: Rudraksha Gupta
Cc: agross, bjorn.andersson, david, devicetree,
krzysztof.kozlowski+dt, linux-arm-msm, linux-kernel, robh+dt
On 09/08/2022 03:03, Rudraksha Gupta wrote:
> This adds a very basic device tree file for the Samsung Galaxy Express
> SGH-I437. Currently, the following things work: UART, eMMC, SD Card, and
> USB.
Use subject prefix matching the subsystem.
>
> Signed-off-by: Rudraksha Gupta <guptarud@gmail.com>
> ---
> v2:
> - Group the correct changes together
>
> arch/arm/boot/dts/Makefile | 1 +
> .../dts/qcom-msm8960-samsung-expressatt.dts | 337 ++++++++++++++++++
> 2 files changed, 338 insertions(+)
> create mode 100644 arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 05d8aef6e5d2..d55f196ad733 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1049,6 +1049,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
> qcom-msm8660-surf.dtb \
> qcom-msm8916-samsung-serranove.dtb \
> qcom-msm8960-cdp.dtb \
> + qcom-msm8960-samsung-expressatt.dtb \
> qcom-msm8974-lge-nexus5-hammerhead.dtb \
> qcom-msm8974-sony-xperia-rhine-amami.dtb \
> qcom-msm8974-sony-xperia-rhine-honami.dtb \
> diff --git a/arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts b/arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts
> new file mode 100644
> index 000000000000..cf557f0c9a59
> --- /dev/null
> +++ b/arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts
> @@ -0,0 +1,337 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +#include <dt-bindings/input/input.h>
> +#include "qcom-msm8960.dtsi"
> +
> +/ {
> + model = "Samsung Galaxy S3 SGH-I437";
> + compatible = "samsung,expressatt", "qcom,msm8960";
Undocumented compatible. Run checkpatch.
> +
> + aliases {
> + serial0 = &gsbi5_serial;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> +
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
These three properties are confusing. Why adding them?
> + };
> +
> + soc {
> + gsbi@16400000 {
Override by alias.
> + status = "ok";
okay, not ok. Status goes at the end of properties.
> + qcom,mode = <GSBI_PROT_I2C_UART>;
> + serial@16440000 {
> + status = "ok";
Same comments.
> + };
> + };
> +
> + amba {
> + /* eMMC */
> + sdcc1: mmc@12400000 {
OK, I'll abandon the review. This file is really not matching anything
in the upstream. Please start your work from a proper upstreamed, recent
board.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v2 2/2] ARM: msm8960: Add Samsung Galaxy Express support
2022-08-09 5:35 ` Krzysztof Kozlowski
@ 2022-08-09 23:57 ` Rudraksha Gupta
2022-08-10 7:47 ` Krzysztof Kozlowski
0 siblings, 1 reply; 13+ messages in thread
From: Rudraksha Gupta @ 2022-08-09 23:57 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: agross, bjorn.andersson, david, devicetree,
krzysztof.kozlowski+dt, linux-arm-msm, linux-kernel, robh+dt
> OK, I'll abandon the review. This file is really not matching anything
> in the upstream. Please start your work from a proper upstreamed, recent
> board.
I based it off of qcom-msm8960-cdp.dts. If there is a dts that you would
like
me to model off of, please link it to me. Otherwise, I will find another
recent
dts and model off of that
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v2 2/2] ARM: msm8960: Add Samsung Galaxy Express support
2022-08-09 23:57 ` Rudraksha Gupta
@ 2022-08-10 7:47 ` Krzysztof Kozlowski
0 siblings, 0 replies; 13+ messages in thread
From: Krzysztof Kozlowski @ 2022-08-10 7:47 UTC (permalink / raw)
To: Rudraksha Gupta
Cc: agross, bjorn.andersson, david, devicetree,
krzysztof.kozlowski+dt, linux-arm-msm, linux-kernel, robh+dt
On 10/08/2022 02:57, Rudraksha Gupta wrote:
> > OK, I'll abandon the review. This file is really not matching anything
>
> > in the upstream. Please start your work from a proper upstreamed, recent
>
> > board.
>
> I based it off of qcom-msm8960-cdp.dts. If there is a dts that you would
> like
>
> me to model off of, please link it to me. Otherwise, I will find another
> recent
>
> dts and model off of that
>
From arm these look good:
arch/arm/boot/dts/qcom-msm8974pro-fairphone-fp2.dts
arch/arm/boot/dts/qcom-msm8974pro-samsung-klte.dts
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v2 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias
2022-08-09 0:02 ` [PATCH v2 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias Rudraksha Gupta
2022-08-09 0:03 ` [PATCH v2 2/2] ARM: msm8960: Add Samsung Galaxy Express support Rudraksha Gupta
2022-08-09 5:32 ` [PATCH v2 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias Krzysztof Kozlowski
@ 2022-08-10 19:53 ` Bjorn Andersson
2022-08-11 2:51 ` Rudraksha Gupta
2 siblings, 1 reply; 13+ messages in thread
From: Bjorn Andersson @ 2022-08-10 19:53 UTC (permalink / raw)
To: Rudraksha Gupta
Cc: agross, david, devicetree, krzysztof.kozlowski+dt, linux-arm-msm,
linux-kernel, robh+dt
On Mon 08 Aug 17:02 PDT 2022, Rudraksha Gupta wrote:
> This patch renames cxo_board to be up to date with the current naming
> style. It also adds an alias.
>
> Signed-off-by: Rudraksha Gupta <guptarud@gmail.com>
> ---
> v2:
> - Group the correct changes together
>
> arch/arm/boot/dts/qcom-msm8960.dtsi | 2 +-
> drivers/clk/qcom/gcc-msm8960.c | 2 +-
Clock and dts patches goes through two different paths towards mainline,
so they should be separated.
> 2 files changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi
> index 0e099aa7c889..2ed969785b78 100644
> --- a/arch/arm/boot/dts/qcom-msm8960.dtsi
> +++ b/arch/arm/boot/dts/qcom-msm8960.dtsi
> @@ -58,7 +58,7 @@ cpu-pmu {
> };
>
> clocks {
> - cxo_board {
> + cxo_board: cxo-board {
> compatible = "fixed-clock";
> #clock-cells = <0>;
> clock-frequency = <19200000>;
> diff --git a/drivers/clk/qcom/gcc-msm8960.c b/drivers/clk/qcom/gcc-msm8960.c
> index 051745ef99c8..56ce05a846dd 100644
> --- a/drivers/clk/qcom/gcc-msm8960.c
> +++ b/drivers/clk/qcom/gcc-msm8960.c
> @@ -3624,7 +3624,7 @@ static int gcc_msm8960_probe(struct platform_device *pdev)
> if (!match)
> return -EINVAL;
>
> - ret = qcom_cc_register_board_clk(dev, "cxo_board", "cxo", 19200000);
> + ret = qcom_cc_register_board_clk(dev, "cxo-board", "cxo", 19200000);
This breaks compatibility with existing DTB files.
What you probably want is to make sure that any clocks with parent name
of "cxo", should have a .fw_name = "cxo", then you can make a
phandle-based reference in DT and these global names doesn't matter (and
in the end we can remove this board_clk from the driver).
Regards,
Bjorn
> if (ret)
> return ret;
>
> --
> 2.25.1
>
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v2 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias
2022-08-10 19:53 ` Bjorn Andersson
@ 2022-08-11 2:51 ` Rudraksha Gupta
2022-08-29 21:54 ` Bjorn Andersson
0 siblings, 1 reply; 13+ messages in thread
From: Rudraksha Gupta @ 2022-08-11 2:51 UTC (permalink / raw)
To: Bjorn Andersson
Cc: agross, david, devicetree, krzysztof.kozlowski+dt, linux-arm-msm,
linux-kernel, robh+dt
> Clock and dts patches goes through two different paths towards mainline,
> so they should be separated.
Gotcha, thanks. I will do that.
> This breaks compatibility with existing DTB files.
> What you probably want is to make sure that any clocks with parent name
> of "cxo", should have a .fw_name = "cxo", then you can make a
> phandle-based reference in DT and these global names doesn't matter (and
> in the end we can remove this board_clk from the driver).
Ah, I see. If I understand correctly, it should be something like this,
right?
https://github.com/torvalds/linux/blob/master/drivers/clk/qcom/gcc-msm8996.c#L169-L172
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v2 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias
2022-08-11 2:51 ` Rudraksha Gupta
@ 2022-08-29 21:54 ` Bjorn Andersson
2023-02-21 6:40 ` Rudraksha Gupta
0 siblings, 1 reply; 13+ messages in thread
From: Bjorn Andersson @ 2022-08-29 21:54 UTC (permalink / raw)
To: Rudraksha Gupta
Cc: Bjorn Andersson, agross, david, devicetree,
krzysztof.kozlowski+dt, linux-arm-msm, linux-kernel, robh+dt
On Wed, Aug 10, 2022 at 10:51:51PM -0400, Rudraksha Gupta wrote:
> > Clock and dts patches goes through two different paths towards mainline,
>
> > so they should be separated.
>
> Gotcha, thanks. I will do that.
>
>
> > This breaks compatibility with existing DTB files.
>
> > What you probably want is to make sure that any clocks with parent name
>
> > of "cxo", should have a .fw_name = "cxo", then you can make a
>
> > phandle-based reference in DT and these global names doesn't matter (and
>
> > in the end we can remove this board_clk from the driver).
>
> Ah, I see. If I understand correctly, it should be something like this,
> right?
> https://github.com/torvalds/linux/blob/master/drivers/clk/qcom/gcc-msm8996.c#L169-L172
Correct, this will try to find the clock by clock-names of "cxo" and if
not found fall back to do a lookup globally just on the name "xo_board".
So it seems making .name "cxo_board" should handle both cases nicely.
Regards,
Bjorn
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v2 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias
2022-08-29 21:54 ` Bjorn Andersson
@ 2023-02-21 6:40 ` Rudraksha Gupta
0 siblings, 0 replies; 13+ messages in thread
From: Rudraksha Gupta @ 2023-02-21 6:40 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Bjorn Andersson, agross, david, devicetree,
krzysztof.kozlowski+dt, linux-arm-msm, linux-kernel, robh+dt
Hello,
So I'm trying to add a cxo-board node to my dts, however the current
implementation seems like it wants cxo_board. It was recommended a while
ago that I refactor gcc-msm8960.c to be more like
https://github.com/torvalds/linux/blob/master/drivers/clk/qcom/gcc-msm8996.c#L36
. However, I have a couple of questions:
- The xo struct that I listed above is listed in another struct
https://github.com/torvalds/linux/blob/master/drivers/clk/qcom/gcc-msm8996.c#L3408
which is listed in the SoC desc struct
https://github.com/torvalds/linux/blob/master/drivers/clk/qcom/gcc-msm8996.c#L3818
. My question is that even though gcc-msm8960.c has an msm8960/apq8064
desc struct, it doesn't have anything like gcc_msm8996_hws. How would I
know what goes in a hypothetical gcc_(msm8960/apq8064)_hws struct? I'm
assuming that all I need in the hw struct is the pxo and cxo listed here
https://github.com/torvalds/linux/blob/master/drivers/clk/qcom/gcc-msm8960.c#L3727
however I'm not 100% sure how to verify this. Would anything else go
into a hypothetical gcc_(msm8960/apq8064)_hws struct?
- Is there documentation on how the gcc-<soc> files work? I'm still
quite new to contributing to the Linux kernel and would like to learn
more about the modern way to format these files and to learn more about
how they work in general
Thanks,
Rudraksha
^ permalink raw reply [flat|nested] 13+ messages in thread
end of thread, other threads:[~2023-02-21 6:40 UTC | newest]
Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-08-08 23:47 [PATCH 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias Rudraksha Gupta
2022-08-08 23:47 ` [PATCH 2/2] ARM: msm8960: Add Samsung Galaxy Express support Rudraksha Gupta
2022-08-09 0:02 ` [PATCH v2 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias Rudraksha Gupta
2022-08-09 0:03 ` [PATCH v2 2/2] ARM: msm8960: Add Samsung Galaxy Express support Rudraksha Gupta
2022-08-09 5:35 ` Krzysztof Kozlowski
2022-08-09 23:57 ` Rudraksha Gupta
2022-08-10 7:47 ` Krzysztof Kozlowski
2022-08-09 5:32 ` [PATCH v2 1/2] ARM: msm8960: Rename cxo_board to cxo-board and add alias Krzysztof Kozlowski
2022-08-10 19:53 ` Bjorn Andersson
2022-08-11 2:51 ` Rudraksha Gupta
2022-08-29 21:54 ` Bjorn Andersson
2023-02-21 6:40 ` Rudraksha Gupta
2022-08-09 5:30 ` [PATCH " Krzysztof Kozlowski
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.