* [PATCH 0/3] drm: panel: add support for TDO tl070wsh30 panel @ 2020-09-07 11:10 ` Neil Armstrong 0 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-07 11:10 UTC (permalink / raw) To: thierry.reding, sam Cc: dri-devel, linux-amlogic, linux-kernel, Neil Armstrong This adds support bindings and support for the TDO TL070WSH30 TFT-LCD panel module shipped with the Amlogic S400 Development Kit. The panel has a 1024×600 resolution and uses 24 bit RGB per pixel. It provides a MIPI DSI interface to the host, a built-in LED backlight and touch controller. Changes since v1 at [1]: - added missing vendor-prefixes patch - removed vrefresh - fixed warning on add_panel return - removed DRM logging [1] https://patchwork.freedesktop.org/series/81376/#rev1 Neil Armstrong (3): dt-bindings: vendor-prefixes: Add Shanghai Top Display Optolelectronics vendor prefix dt-bindings: display: panel: add TDO tl070wsh30 DSI panel bindings drm: panel: add TDO tl070wsh30 panel driver .../display/panel/tdo,tl070wsh30.yaml | 58 ++++ .../devicetree/bindings/vendor-prefixes.yaml | 2 + drivers/gpu/drm/panel/Kconfig | 11 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c | 256 ++++++++++++++++++ 5 files changed, 328 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml create mode 100644 drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c -- 2.22.0 ^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH 0/3] drm: panel: add support for TDO tl070wsh30 panel @ 2020-09-07 11:10 ` Neil Armstrong 0 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-07 11:10 UTC (permalink / raw) To: thierry.reding, sam Cc: linux-amlogic, linux-kernel, dri-devel, Neil Armstrong This adds support bindings and support for the TDO TL070WSH30 TFT-LCD panel module shipped with the Amlogic S400 Development Kit. The panel has a 1024×600 resolution and uses 24 bit RGB per pixel. It provides a MIPI DSI interface to the host, a built-in LED backlight and touch controller. Changes since v1 at [1]: - added missing vendor-prefixes patch - removed vrefresh - fixed warning on add_panel return - removed DRM logging [1] https://patchwork.freedesktop.org/series/81376/#rev1 Neil Armstrong (3): dt-bindings: vendor-prefixes: Add Shanghai Top Display Optolelectronics vendor prefix dt-bindings: display: panel: add TDO tl070wsh30 DSI panel bindings drm: panel: add TDO tl070wsh30 panel driver .../display/panel/tdo,tl070wsh30.yaml | 58 ++++ .../devicetree/bindings/vendor-prefixes.yaml | 2 + drivers/gpu/drm/panel/Kconfig | 11 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c | 256 ++++++++++++++++++ 5 files changed, 328 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml create mode 100644 drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c -- 2.22.0 _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH 0/3] drm: panel: add support for TDO tl070wsh30 panel @ 2020-09-07 11:10 ` Neil Armstrong 0 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-07 11:10 UTC (permalink / raw) To: thierry.reding, sam Cc: linux-amlogic, linux-kernel, dri-devel, Neil Armstrong This adds support bindings and support for the TDO TL070WSH30 TFT-LCD panel module shipped with the Amlogic S400 Development Kit. The panel has a 1024×600 resolution and uses 24 bit RGB per pixel. It provides a MIPI DSI interface to the host, a built-in LED backlight and touch controller. Changes since v1 at [1]: - added missing vendor-prefixes patch - removed vrefresh - fixed warning on add_panel return - removed DRM logging [1] https://patchwork.freedesktop.org/series/81376/#rev1 Neil Armstrong (3): dt-bindings: vendor-prefixes: Add Shanghai Top Display Optolelectronics vendor prefix dt-bindings: display: panel: add TDO tl070wsh30 DSI panel bindings drm: panel: add TDO tl070wsh30 panel driver .../display/panel/tdo,tl070wsh30.yaml | 58 ++++ .../devicetree/bindings/vendor-prefixes.yaml | 2 + drivers/gpu/drm/panel/Kconfig | 11 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c | 256 ++++++++++++++++++ 5 files changed, 328 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml create mode 100644 drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c -- 2.22.0 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add Shanghai Top Display Optolelectronics vendor prefix 2020-09-07 11:10 ` Neil Armstrong (?) @ 2020-09-07 11:10 ` Neil Armstrong -1 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-07 11:10 UTC (permalink / raw) To: thierry.reding, sam, devicetree Cc: dri-devel, linux-amlogic, linux-kernel, Neil Armstrong Shanghai Top Display Optolelectronics Co., Ltd is a display manufacturer from Shanghai. Web site of the company: http://www.shtdo.com/ Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index a1e4356cf522..4e9dfb352c68 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -1078,6 +1078,8 @@ patternProperties: description: TPK U.S.A. LLC "^tplink,.*": description: TP-LINK Technologies Co., Ltd. + "^tdo,.*": + description: Shangai Top Display Optoelectronics Co., Ltd "^tpo,.*": description: TPO "^tq,.*": -- 2.22.0 ^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add Shanghai Top Display Optolelectronics vendor prefix @ 2020-09-07 11:10 ` Neil Armstrong 0 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-07 11:10 UTC (permalink / raw) To: thierry.reding, sam, devicetree Cc: linux-amlogic, linux-kernel, dri-devel, Neil Armstrong Shanghai Top Display Optolelectronics Co., Ltd is a display manufacturer from Shanghai. Web site of the company: http://www.shtdo.com/ Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index a1e4356cf522..4e9dfb352c68 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -1078,6 +1078,8 @@ patternProperties: description: TPK U.S.A. LLC "^tplink,.*": description: TP-LINK Technologies Co., Ltd. + "^tdo,.*": + description: Shangai Top Display Optoelectronics Co., Ltd "^tpo,.*": description: TPO "^tq,.*": -- 2.22.0 _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add Shanghai Top Display Optolelectronics vendor prefix @ 2020-09-07 11:10 ` Neil Armstrong 0 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-07 11:10 UTC (permalink / raw) To: thierry.reding, sam, devicetree Cc: linux-amlogic, linux-kernel, dri-devel, Neil Armstrong Shanghai Top Display Optolelectronics Co., Ltd is a display manufacturer from Shanghai. Web site of the company: http://www.shtdo.com/ Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index a1e4356cf522..4e9dfb352c68 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -1078,6 +1078,8 @@ patternProperties: description: TPK U.S.A. LLC "^tplink,.*": description: TP-LINK Technologies Co., Ltd. + "^tdo,.*": + description: Shangai Top Display Optoelectronics Co., Ltd "^tpo,.*": description: TPO "^tq,.*": -- 2.22.0 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v2 2/3] dt-bindings: display: panel: add TDO tl070wsh30 DSI panel bindings 2020-09-07 11:10 ` Neil Armstrong (?) @ 2020-09-07 11:10 ` Neil Armstrong -1 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-07 11:10 UTC (permalink / raw) To: thierry.reding, sam, devicetree Cc: dri-devel, linux-amlogic, linux-kernel, Neil Armstrong This add the bindings for the 1024*600 tl070wsh30 DSI panel. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- .../display/panel/tdo,tl070wsh30.yaml | 58 +++++++++++++++++++ 1 file changed, 58 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml diff --git a/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml new file mode 100644 index 000000000000..20f4fdedfcb0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) +# Copyright 2020 BayLibre, SAS +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/tdo,tl070wsh30.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TDO TL070WSH30 DSI panel + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + + compatible: + enum: + - tdo,tl070wsh30 + + reg: + maxItems: 1 + description: DSI virtual channel + + backlight: true + reset-gpios: true + port: true + power-supply: true + +additionalProperties: false + +required: + - compatible + - power-supply + - reset-gpios + - port + - reg + +examples: + - | + dsi { + #address-cells = <1>; + #size-cells = <0>; + panel@0 { + compatible = "tdo,tl070wsh30"; + reg = <0>; + power-supply = <&vcc_lcd_reg>; + backlight = <&panel_backlight>; + reset-gpios = <&gpio_reset>; + + port { + panel: endpoint { + remote-endpoint = <&mipi_dsi_out>; + }; + }; + }; + }; -- 2.22.0 ^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v2 2/3] dt-bindings: display: panel: add TDO tl070wsh30 DSI panel bindings @ 2020-09-07 11:10 ` Neil Armstrong 0 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-07 11:10 UTC (permalink / raw) To: thierry.reding, sam, devicetree Cc: linux-amlogic, linux-kernel, dri-devel, Neil Armstrong This add the bindings for the 1024*600 tl070wsh30 DSI panel. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- .../display/panel/tdo,tl070wsh30.yaml | 58 +++++++++++++++++++ 1 file changed, 58 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml diff --git a/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml new file mode 100644 index 000000000000..20f4fdedfcb0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) +# Copyright 2020 BayLibre, SAS +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/tdo,tl070wsh30.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TDO TL070WSH30 DSI panel + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + + compatible: + enum: + - tdo,tl070wsh30 + + reg: + maxItems: 1 + description: DSI virtual channel + + backlight: true + reset-gpios: true + port: true + power-supply: true + +additionalProperties: false + +required: + - compatible + - power-supply + - reset-gpios + - port + - reg + +examples: + - | + dsi { + #address-cells = <1>; + #size-cells = <0>; + panel@0 { + compatible = "tdo,tl070wsh30"; + reg = <0>; + power-supply = <&vcc_lcd_reg>; + backlight = <&panel_backlight>; + reset-gpios = <&gpio_reset>; + + port { + panel: endpoint { + remote-endpoint = <&mipi_dsi_out>; + }; + }; + }; + }; -- 2.22.0 _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v2 2/3] dt-bindings: display: panel: add TDO tl070wsh30 DSI panel bindings @ 2020-09-07 11:10 ` Neil Armstrong 0 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-07 11:10 UTC (permalink / raw) To: thierry.reding, sam, devicetree Cc: linux-amlogic, linux-kernel, dri-devel, Neil Armstrong This add the bindings for the 1024*600 tl070wsh30 DSI panel. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- .../display/panel/tdo,tl070wsh30.yaml | 58 +++++++++++++++++++ 1 file changed, 58 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml diff --git a/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml new file mode 100644 index 000000000000..20f4fdedfcb0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) +# Copyright 2020 BayLibre, SAS +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/tdo,tl070wsh30.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TDO TL070WSH30 DSI panel + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + + compatible: + enum: + - tdo,tl070wsh30 + + reg: + maxItems: 1 + description: DSI virtual channel + + backlight: true + reset-gpios: true + port: true + power-supply: true + +additionalProperties: false + +required: + - compatible + - power-supply + - reset-gpios + - port + - reg + +examples: + - | + dsi { + #address-cells = <1>; + #size-cells = <0>; + panel@0 { + compatible = "tdo,tl070wsh30"; + reg = <0>; + power-supply = <&vcc_lcd_reg>; + backlight = <&panel_backlight>; + reset-gpios = <&gpio_reset>; + + port { + panel: endpoint { + remote-endpoint = <&mipi_dsi_out>; + }; + }; + }; + }; -- 2.22.0 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 27+ messages in thread
* Re: [PATCH v2 2/3] dt-bindings: display: panel: add TDO tl070wsh30 DSI panel bindings 2020-09-07 11:10 ` Neil Armstrong (?) @ 2020-09-07 11:45 ` Sam Ravnborg -1 siblings, 0 replies; 27+ messages in thread From: Sam Ravnborg @ 2020-09-07 11:45 UTC (permalink / raw) To: Neil Armstrong Cc: thierry.reding, devicetree, dri-devel, linux-amlogic, linux-kernel Hi Neil. On Mon, Sep 07, 2020 at 01:10:26PM +0200, Neil Armstrong wrote: > This add the bindings for the 1024*600 tl070wsh30 DSI panel. The binding looks like a panel-simple-dsi.yaml candidate. Only differen is enable-gpios versus reset-gpios Could you check if we can use panel-simple-dsi-yaml. Sam > > Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> > --- > .../display/panel/tdo,tl070wsh30.yaml | 58 +++++++++++++++++++ > 1 file changed, 58 insertions(+) > create mode 100644 Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > > diff --git a/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > new file mode 100644 > index 000000000000..20f4fdedfcb0 > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > @@ -0,0 +1,58 @@ > +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) > +# Copyright 2020 BayLibre, SAS > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/display/panel/tdo,tl070wsh30.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: TDO TL070WSH30 DSI panel > + > +maintainers: > + - Neil Armstrong <narmstrong@baylibre.com> > + > +allOf: > + - $ref: panel-common.yaml# > + > +properties: > + > + compatible: > + enum: > + - tdo,tl070wsh30 > + > + reg: > + maxItems: 1 > + description: DSI virtual channel > + > + backlight: true > + reset-gpios: true > + port: true > + power-supply: true > + > +additionalProperties: false > + > +required: > + - compatible > + - power-supply > + - reset-gpios > + - port > + - reg > + > +examples: > + - | > + dsi { > + #address-cells = <1>; > + #size-cells = <0>; > + panel@0 { > + compatible = "tdo,tl070wsh30"; > + reg = <0>; > + power-supply = <&vcc_lcd_reg>; > + backlight = <&panel_backlight>; > + reset-gpios = <&gpio_reset>; > + > + port { > + panel: endpoint { > + remote-endpoint = <&mipi_dsi_out>; > + }; > + }; > + }; > + }; > -- > 2.22.0 ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v2 2/3] dt-bindings: display: panel: add TDO tl070wsh30 DSI panel bindings @ 2020-09-07 11:45 ` Sam Ravnborg 0 siblings, 0 replies; 27+ messages in thread From: Sam Ravnborg @ 2020-09-07 11:45 UTC (permalink / raw) To: Neil Armstrong Cc: devicetree, thierry.reding, linux-kernel, dri-devel, linux-amlogic Hi Neil. On Mon, Sep 07, 2020 at 01:10:26PM +0200, Neil Armstrong wrote: > This add the bindings for the 1024*600 tl070wsh30 DSI panel. The binding looks like a panel-simple-dsi.yaml candidate. Only differen is enable-gpios versus reset-gpios Could you check if we can use panel-simple-dsi-yaml. Sam > > Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> > --- > .../display/panel/tdo,tl070wsh30.yaml | 58 +++++++++++++++++++ > 1 file changed, 58 insertions(+) > create mode 100644 Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > > diff --git a/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > new file mode 100644 > index 000000000000..20f4fdedfcb0 > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > @@ -0,0 +1,58 @@ > +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) > +# Copyright 2020 BayLibre, SAS > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/display/panel/tdo,tl070wsh30.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: TDO TL070WSH30 DSI panel > + > +maintainers: > + - Neil Armstrong <narmstrong@baylibre.com> > + > +allOf: > + - $ref: panel-common.yaml# > + > +properties: > + > + compatible: > + enum: > + - tdo,tl070wsh30 > + > + reg: > + maxItems: 1 > + description: DSI virtual channel > + > + backlight: true > + reset-gpios: true > + port: true > + power-supply: true > + > +additionalProperties: false > + > +required: > + - compatible > + - power-supply > + - reset-gpios > + - port > + - reg > + > +examples: > + - | > + dsi { > + #address-cells = <1>; > + #size-cells = <0>; > + panel@0 { > + compatible = "tdo,tl070wsh30"; > + reg = <0>; > + power-supply = <&vcc_lcd_reg>; > + backlight = <&panel_backlight>; > + reset-gpios = <&gpio_reset>; > + > + port { > + panel: endpoint { > + remote-endpoint = <&mipi_dsi_out>; > + }; > + }; > + }; > + }; > -- > 2.22.0 _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v2 2/3] dt-bindings: display: panel: add TDO tl070wsh30 DSI panel bindings @ 2020-09-07 11:45 ` Sam Ravnborg 0 siblings, 0 replies; 27+ messages in thread From: Sam Ravnborg @ 2020-09-07 11:45 UTC (permalink / raw) To: Neil Armstrong Cc: devicetree, thierry.reding, linux-kernel, dri-devel, linux-amlogic Hi Neil. On Mon, Sep 07, 2020 at 01:10:26PM +0200, Neil Armstrong wrote: > This add the bindings for the 1024*600 tl070wsh30 DSI panel. The binding looks like a panel-simple-dsi.yaml candidate. Only differen is enable-gpios versus reset-gpios Could you check if we can use panel-simple-dsi-yaml. Sam > > Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> > --- > .../display/panel/tdo,tl070wsh30.yaml | 58 +++++++++++++++++++ > 1 file changed, 58 insertions(+) > create mode 100644 Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > > diff --git a/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > new file mode 100644 > index 000000000000..20f4fdedfcb0 > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > @@ -0,0 +1,58 @@ > +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) > +# Copyright 2020 BayLibre, SAS > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/display/panel/tdo,tl070wsh30.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: TDO TL070WSH30 DSI panel > + > +maintainers: > + - Neil Armstrong <narmstrong@baylibre.com> > + > +allOf: > + - $ref: panel-common.yaml# > + > +properties: > + > + compatible: > + enum: > + - tdo,tl070wsh30 > + > + reg: > + maxItems: 1 > + description: DSI virtual channel > + > + backlight: true > + reset-gpios: true > + port: true > + power-supply: true > + > +additionalProperties: false > + > +required: > + - compatible > + - power-supply > + - reset-gpios > + - port > + - reg > + > +examples: > + - | > + dsi { > + #address-cells = <1>; > + #size-cells = <0>; > + panel@0 { > + compatible = "tdo,tl070wsh30"; > + reg = <0>; > + power-supply = <&vcc_lcd_reg>; > + backlight = <&panel_backlight>; > + reset-gpios = <&gpio_reset>; > + > + port { > + panel: endpoint { > + remote-endpoint = <&mipi_dsi_out>; > + }; > + }; > + }; > + }; > -- > 2.22.0 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v2 2/3] dt-bindings: display: panel: add TDO tl070wsh30 DSI panel bindings 2020-09-07 11:45 ` Sam Ravnborg (?) @ 2020-09-07 13:24 ` Neil Armstrong -1 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-07 13:24 UTC (permalink / raw) To: Sam Ravnborg Cc: thierry.reding, devicetree, dri-devel, linux-amlogic, linux-kernel Hi, On 07/09/2020 13:45, Sam Ravnborg wrote: > Hi Neil. > > On Mon, Sep 07, 2020 at 01:10:26PM +0200, Neil Armstrong wrote: >> This add the bindings for the 1024*600 tl070wsh30 DSI panel. > > The binding looks like a panel-simple-dsi.yaml candidate. > Only differen is enable-gpios versus reset-gpios This is the only difference, the panel only has a reset signal and no enable signal. But I can add a reset-gpios to panel-simple-dsi.yaml, would it be ok ? Neil > > Could you check if we can use panel-simple-dsi-yaml. > > Sam > >> >> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> >> --- >> .../display/panel/tdo,tl070wsh30.yaml | 58 +++++++++++++++++++ >> 1 file changed, 58 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml >> >> diff --git a/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml >> new file mode 100644 >> index 000000000000..20f4fdedfcb0 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml >> @@ -0,0 +1,58 @@ >> +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) >> +# Copyright 2020 BayLibre, SAS >> +%YAML 1.2 >> +--- >> +$id: http://devicetree.org/schemas/display/panel/tdo,tl070wsh30.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: TDO TL070WSH30 DSI panel >> + >> +maintainers: >> + - Neil Armstrong <narmstrong@baylibre.com> >> + >> +allOf: >> + - $ref: panel-common.yaml# >> + >> +properties: >> + >> + compatible: >> + enum: >> + - tdo,tl070wsh30 >> + >> + reg: >> + maxItems: 1 >> + description: DSI virtual channel >> + >> + backlight: true >> + reset-gpios: true >> + port: true >> + power-supply: true >> + >> +additionalProperties: false >> + >> +required: >> + - compatible >> + - power-supply >> + - reset-gpios >> + - port >> + - reg >> + >> +examples: >> + - | >> + dsi { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + panel@0 { >> + compatible = "tdo,tl070wsh30"; >> + reg = <0>; >> + power-supply = <&vcc_lcd_reg>; >> + backlight = <&panel_backlight>; >> + reset-gpios = <&gpio_reset>; >> + >> + port { >> + panel: endpoint { >> + remote-endpoint = <&mipi_dsi_out>; >> + }; >> + }; >> + }; >> + }; >> -- >> 2.22.0 ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v2 2/3] dt-bindings: display: panel: add TDO tl070wsh30 DSI panel bindings @ 2020-09-07 13:24 ` Neil Armstrong 0 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-07 13:24 UTC (permalink / raw) To: Sam Ravnborg Cc: devicetree, thierry.reding, linux-kernel, dri-devel, linux-amlogic Hi, On 07/09/2020 13:45, Sam Ravnborg wrote: > Hi Neil. > > On Mon, Sep 07, 2020 at 01:10:26PM +0200, Neil Armstrong wrote: >> This add the bindings for the 1024*600 tl070wsh30 DSI panel. > > The binding looks like a panel-simple-dsi.yaml candidate. > Only differen is enable-gpios versus reset-gpios This is the only difference, the panel only has a reset signal and no enable signal. But I can add a reset-gpios to panel-simple-dsi.yaml, would it be ok ? Neil > > Could you check if we can use panel-simple-dsi-yaml. > > Sam > >> >> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> >> --- >> .../display/panel/tdo,tl070wsh30.yaml | 58 +++++++++++++++++++ >> 1 file changed, 58 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml >> >> diff --git a/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml >> new file mode 100644 >> index 000000000000..20f4fdedfcb0 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml >> @@ -0,0 +1,58 @@ >> +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) >> +# Copyright 2020 BayLibre, SAS >> +%YAML 1.2 >> +--- >> +$id: http://devicetree.org/schemas/display/panel/tdo,tl070wsh30.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: TDO TL070WSH30 DSI panel >> + >> +maintainers: >> + - Neil Armstrong <narmstrong@baylibre.com> >> + >> +allOf: >> + - $ref: panel-common.yaml# >> + >> +properties: >> + >> + compatible: >> + enum: >> + - tdo,tl070wsh30 >> + >> + reg: >> + maxItems: 1 >> + description: DSI virtual channel >> + >> + backlight: true >> + reset-gpios: true >> + port: true >> + power-supply: true >> + >> +additionalProperties: false >> + >> +required: >> + - compatible >> + - power-supply >> + - reset-gpios >> + - port >> + - reg >> + >> +examples: >> + - | >> + dsi { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + panel@0 { >> + compatible = "tdo,tl070wsh30"; >> + reg = <0>; >> + power-supply = <&vcc_lcd_reg>; >> + backlight = <&panel_backlight>; >> + reset-gpios = <&gpio_reset>; >> + >> + port { >> + panel: endpoint { >> + remote-endpoint = <&mipi_dsi_out>; >> + }; >> + }; >> + }; >> + }; >> -- >> 2.22.0 _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v2 2/3] dt-bindings: display: panel: add TDO tl070wsh30 DSI panel bindings @ 2020-09-07 13:24 ` Neil Armstrong 0 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-07 13:24 UTC (permalink / raw) To: Sam Ravnborg Cc: devicetree, thierry.reding, linux-kernel, dri-devel, linux-amlogic Hi, On 07/09/2020 13:45, Sam Ravnborg wrote: > Hi Neil. > > On Mon, Sep 07, 2020 at 01:10:26PM +0200, Neil Armstrong wrote: >> This add the bindings for the 1024*600 tl070wsh30 DSI panel. > > The binding looks like a panel-simple-dsi.yaml candidate. > Only differen is enable-gpios versus reset-gpios This is the only difference, the panel only has a reset signal and no enable signal. But I can add a reset-gpios to panel-simple-dsi.yaml, would it be ok ? Neil > > Could you check if we can use panel-simple-dsi-yaml. > > Sam > >> >> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> >> --- >> .../display/panel/tdo,tl070wsh30.yaml | 58 +++++++++++++++++++ >> 1 file changed, 58 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml >> >> diff --git a/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml >> new file mode 100644 >> index 000000000000..20f4fdedfcb0 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml >> @@ -0,0 +1,58 @@ >> +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) >> +# Copyright 2020 BayLibre, SAS >> +%YAML 1.2 >> +--- >> +$id: http://devicetree.org/schemas/display/panel/tdo,tl070wsh30.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: TDO TL070WSH30 DSI panel >> + >> +maintainers: >> + - Neil Armstrong <narmstrong@baylibre.com> >> + >> +allOf: >> + - $ref: panel-common.yaml# >> + >> +properties: >> + >> + compatible: >> + enum: >> + - tdo,tl070wsh30 >> + >> + reg: >> + maxItems: 1 >> + description: DSI virtual channel >> + >> + backlight: true >> + reset-gpios: true >> + port: true >> + power-supply: true >> + >> +additionalProperties: false >> + >> +required: >> + - compatible >> + - power-supply >> + - reset-gpios >> + - port >> + - reg >> + >> +examples: >> + - | >> + dsi { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + panel@0 { >> + compatible = "tdo,tl070wsh30"; >> + reg = <0>; >> + power-supply = <&vcc_lcd_reg>; >> + backlight = <&panel_backlight>; >> + reset-gpios = <&gpio_reset>; >> + >> + port { >> + panel: endpoint { >> + remote-endpoint = <&mipi_dsi_out>; >> + }; >> + }; >> + }; >> + }; >> -- >> 2.22.0 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v2 2/3] dt-bindings: display: panel: add TDO tl070wsh30 DSI panel bindings 2020-09-07 13:24 ` Neil Armstrong (?) @ 2020-09-07 19:24 ` Sam Ravnborg -1 siblings, 0 replies; 27+ messages in thread From: Sam Ravnborg @ 2020-09-07 19:24 UTC (permalink / raw) To: Neil Armstrong Cc: devicetree, thierry.reding, linux-kernel, dri-devel, linux-amlogic Hi Neil. On Mon, Sep 07, 2020 at 03:24:47PM +0200, Neil Armstrong wrote: > Hi, > > On 07/09/2020 13:45, Sam Ravnborg wrote: > > Hi Neil. > > > > On Mon, Sep 07, 2020 at 01:10:26PM +0200, Neil Armstrong wrote: > >> This add the bindings for the 1024*600 tl070wsh30 DSI panel. > > > > The binding looks like a panel-simple-dsi.yaml candidate. > > Only differen is enable-gpios versus reset-gpios > > This is the only difference, the panel only has a reset signal and no > enable signal. > > But I can add a reset-gpios to panel-simple-dsi.yaml, would it be ok ? Yes, that would be fine as long as it is not a required property. It was a mistake we did not add it from the beginning. There has been patches floating to add reset-gpios to panle.simple.c that I rejected - this was also wrong. Really simple and dumb panels has no reset but dsi panels that panel-simple supports too has a reset. Sam > > Neil > > > > > Could you check if we can use panel-simple-dsi-yaml. > > > > Sam > > > >> > >> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> > >> --- > >> .../display/panel/tdo,tl070wsh30.yaml | 58 +++++++++++++++++++ > >> 1 file changed, 58 insertions(+) > >> create mode 100644 Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > >> > >> diff --git a/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > >> new file mode 100644 > >> index 000000000000..20f4fdedfcb0 > >> --- /dev/null > >> +++ b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > >> @@ -0,0 +1,58 @@ > >> +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) > >> +# Copyright 2020 BayLibre, SAS > >> +%YAML 1.2 > >> +--- > >> +$id: http://devicetree.org/schemas/display/panel/tdo,tl070wsh30.yaml# > >> +$schema: http://devicetree.org/meta-schemas/core.yaml# > >> + > >> +title: TDO TL070WSH30 DSI panel > >> + > >> +maintainers: > >> + - Neil Armstrong <narmstrong@baylibre.com> > >> + > >> +allOf: > >> + - $ref: panel-common.yaml# > >> + > >> +properties: > >> + > >> + compatible: > >> + enum: > >> + - tdo,tl070wsh30 > >> + > >> + reg: > >> + maxItems: 1 > >> + description: DSI virtual channel > >> + > >> + backlight: true > >> + reset-gpios: true > >> + port: true > >> + power-supply: true > >> + > >> +additionalProperties: false > >> + > >> +required: > >> + - compatible > >> + - power-supply > >> + - reset-gpios > >> + - port > >> + - reg > >> + > >> +examples: > >> + - | > >> + dsi { > >> + #address-cells = <1>; > >> + #size-cells = <0>; > >> + panel@0 { > >> + compatible = "tdo,tl070wsh30"; > >> + reg = <0>; > >> + power-supply = <&vcc_lcd_reg>; > >> + backlight = <&panel_backlight>; > >> + reset-gpios = <&gpio_reset>; > >> + > >> + port { > >> + panel: endpoint { > >> + remote-endpoint = <&mipi_dsi_out>; > >> + }; > >> + }; > >> + }; > >> + }; > >> -- > >> 2.22.0 > > _______________________________________________ > dri-devel mailing list > dri-devel@lists.freedesktop.org > https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v2 2/3] dt-bindings: display: panel: add TDO tl070wsh30 DSI panel bindings @ 2020-09-07 19:24 ` Sam Ravnborg 0 siblings, 0 replies; 27+ messages in thread From: Sam Ravnborg @ 2020-09-07 19:24 UTC (permalink / raw) To: Neil Armstrong Cc: devicetree, thierry.reding, linux-kernel, dri-devel, linux-amlogic Hi Neil. On Mon, Sep 07, 2020 at 03:24:47PM +0200, Neil Armstrong wrote: > Hi, > > On 07/09/2020 13:45, Sam Ravnborg wrote: > > Hi Neil. > > > > On Mon, Sep 07, 2020 at 01:10:26PM +0200, Neil Armstrong wrote: > >> This add the bindings for the 1024*600 tl070wsh30 DSI panel. > > > > The binding looks like a panel-simple-dsi.yaml candidate. > > Only differen is enable-gpios versus reset-gpios > > This is the only difference, the panel only has a reset signal and no > enable signal. > > But I can add a reset-gpios to panel-simple-dsi.yaml, would it be ok ? Yes, that would be fine as long as it is not a required property. It was a mistake we did not add it from the beginning. There has been patches floating to add reset-gpios to panle.simple.c that I rejected - this was also wrong. Really simple and dumb panels has no reset but dsi panels that panel-simple supports too has a reset. Sam > > Neil > > > > > Could you check if we can use panel-simple-dsi-yaml. > > > > Sam > > > >> > >> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> > >> --- > >> .../display/panel/tdo,tl070wsh30.yaml | 58 +++++++++++++++++++ > >> 1 file changed, 58 insertions(+) > >> create mode 100644 Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > >> > >> diff --git a/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > >> new file mode 100644 > >> index 000000000000..20f4fdedfcb0 > >> --- /dev/null > >> +++ b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > >> @@ -0,0 +1,58 @@ > >> +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) > >> +# Copyright 2020 BayLibre, SAS > >> +%YAML 1.2 > >> +--- > >> +$id: http://devicetree.org/schemas/display/panel/tdo,tl070wsh30.yaml# > >> +$schema: http://devicetree.org/meta-schemas/core.yaml# > >> + > >> +title: TDO TL070WSH30 DSI panel > >> + > >> +maintainers: > >> + - Neil Armstrong <narmstrong@baylibre.com> > >> + > >> +allOf: > >> + - $ref: panel-common.yaml# > >> + > >> +properties: > >> + > >> + compatible: > >> + enum: > >> + - tdo,tl070wsh30 > >> + > >> + reg: > >> + maxItems: 1 > >> + description: DSI virtual channel > >> + > >> + backlight: true > >> + reset-gpios: true > >> + port: true > >> + power-supply: true > >> + > >> +additionalProperties: false > >> + > >> +required: > >> + - compatible > >> + - power-supply > >> + - reset-gpios > >> + - port > >> + - reg > >> + > >> +examples: > >> + - | > >> + dsi { > >> + #address-cells = <1>; > >> + #size-cells = <0>; > >> + panel@0 { > >> + compatible = "tdo,tl070wsh30"; > >> + reg = <0>; > >> + power-supply = <&vcc_lcd_reg>; > >> + backlight = <&panel_backlight>; > >> + reset-gpios = <&gpio_reset>; > >> + > >> + port { > >> + panel: endpoint { > >> + remote-endpoint = <&mipi_dsi_out>; > >> + }; > >> + }; > >> + }; > >> + }; > >> -- > >> 2.22.0 > > _______________________________________________ > dri-devel mailing list > dri-devel@lists.freedesktop.org > https://lists.freedesktop.org/mailman/listinfo/dri-devel _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v2 2/3] dt-bindings: display: panel: add TDO tl070wsh30 DSI panel bindings @ 2020-09-07 19:24 ` Sam Ravnborg 0 siblings, 0 replies; 27+ messages in thread From: Sam Ravnborg @ 2020-09-07 19:24 UTC (permalink / raw) To: Neil Armstrong Cc: devicetree, thierry.reding, linux-kernel, dri-devel, linux-amlogic Hi Neil. On Mon, Sep 07, 2020 at 03:24:47PM +0200, Neil Armstrong wrote: > Hi, > > On 07/09/2020 13:45, Sam Ravnborg wrote: > > Hi Neil. > > > > On Mon, Sep 07, 2020 at 01:10:26PM +0200, Neil Armstrong wrote: > >> This add the bindings for the 1024*600 tl070wsh30 DSI panel. > > > > The binding looks like a panel-simple-dsi.yaml candidate. > > Only differen is enable-gpios versus reset-gpios > > This is the only difference, the panel only has a reset signal and no > enable signal. > > But I can add a reset-gpios to panel-simple-dsi.yaml, would it be ok ? Yes, that would be fine as long as it is not a required property. It was a mistake we did not add it from the beginning. There has been patches floating to add reset-gpios to panle.simple.c that I rejected - this was also wrong. Really simple and dumb panels has no reset but dsi panels that panel-simple supports too has a reset. Sam > > Neil > > > > > Could you check if we can use panel-simple-dsi-yaml. > > > > Sam > > > >> > >> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> > >> --- > >> .../display/panel/tdo,tl070wsh30.yaml | 58 +++++++++++++++++++ > >> 1 file changed, 58 insertions(+) > >> create mode 100644 Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > >> > >> diff --git a/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > >> new file mode 100644 > >> index 000000000000..20f4fdedfcb0 > >> --- /dev/null > >> +++ b/Documentation/devicetree/bindings/display/panel/tdo,tl070wsh30.yaml > >> @@ -0,0 +1,58 @@ > >> +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) > >> +# Copyright 2020 BayLibre, SAS > >> +%YAML 1.2 > >> +--- > >> +$id: http://devicetree.org/schemas/display/panel/tdo,tl070wsh30.yaml# > >> +$schema: http://devicetree.org/meta-schemas/core.yaml# > >> + > >> +title: TDO TL070WSH30 DSI panel > >> + > >> +maintainers: > >> + - Neil Armstrong <narmstrong@baylibre.com> > >> + > >> +allOf: > >> + - $ref: panel-common.yaml# > >> + > >> +properties: > >> + > >> + compatible: > >> + enum: > >> + - tdo,tl070wsh30 > >> + > >> + reg: > >> + maxItems: 1 > >> + description: DSI virtual channel > >> + > >> + backlight: true > >> + reset-gpios: true > >> + port: true > >> + power-supply: true > >> + > >> +additionalProperties: false > >> + > >> +required: > >> + - compatible > >> + - power-supply > >> + - reset-gpios > >> + - port > >> + - reg > >> + > >> +examples: > >> + - | > >> + dsi { > >> + #address-cells = <1>; > >> + #size-cells = <0>; > >> + panel@0 { > >> + compatible = "tdo,tl070wsh30"; > >> + reg = <0>; > >> + power-supply = <&vcc_lcd_reg>; > >> + backlight = <&panel_backlight>; > >> + reset-gpios = <&gpio_reset>; > >> + > >> + port { > >> + panel: endpoint { > >> + remote-endpoint = <&mipi_dsi_out>; > >> + }; > >> + }; > >> + }; > >> + }; > >> -- > >> 2.22.0 > > _______________________________________________ > dri-devel mailing list > dri-devel@lists.freedesktop.org > https://lists.freedesktop.org/mailman/listinfo/dri-devel _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH v2 3/3] drm: panel: add TDO tl070wsh30 panel driver 2020-09-07 11:10 ` Neil Armstrong (?) @ 2020-09-07 11:10 ` Neil Armstrong -1 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-07 11:10 UTC (permalink / raw) To: thierry.reding, sam Cc: dri-devel, linux-amlogic, linux-kernel, Neil Armstrong This adds support for the TDO TL070WSH30 TFT-LCD panel module. The panel has a 1024×600 resolution and uses 24 bit RGB per pixel. It provides a MIPI DSI interface to the host, a built-in LED backlight and touch controller. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- drivers/gpu/drm/panel/Kconfig | 11 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c | 256 +++++++++++++++++++ 3 files changed, 268 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index 8d97d07c5871..2d488a875b99 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -433,6 +433,17 @@ config DRM_PANEL_SONY_ACX565AKM Say Y here if you want to enable support for the Sony ACX565AKM 800x600 3.5" panel (found on the Nokia N900). +config DRM_PANEL_TDO_TL070WSH30 + tristate "TDO TL070WSH30 DSI panel" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y here if you want to enable support for TDO TL070WSH30 TFT-LCD + panel module. The panel has a 1024×600 resolution and uses + 24 bit RGB per pixel. It provides a MIPI DSI interface to + the host, a built-in LED backlight and touch controller. + config DRM_PANEL_TPO_TD028TTEC1 tristate "Toppoly (TPO) TD028TTEC1 panel driver" depends on OF && SPI diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index 15a4e7752951..35ee06a1b5c2 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -45,6 +45,7 @@ obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.o +obj-$(CONFIG_DRM_PANEL_TDO_TL070WSH30) += panel-tdo-tl070wsh30.o obj-$(CONFIG_DRM_PANEL_TPO_TD028TTEC1) += panel-tpo-td028ttec1.o obj-$(CONFIG_DRM_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o diff --git a/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c new file mode 100644 index 000000000000..c7a6c2c42c52 --- /dev/null +++ b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c @@ -0,0 +1,256 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2020 BayLibre, SAS + * Author: Neil Armstrong <narmstrong@baylibre.com> + */ + +#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/regulator/consumer.h> + +#include <video/mipi_display.h> + +#include <drm/drm_crtc.h> +#include <drm/drm_device.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h> + +struct tdo_tl070wsh30_panel { + struct drm_panel base; + struct mipi_dsi_device *link; + + struct regulator *supply; + struct gpio_desc *reset_gpio; + + bool prepared; +}; + +static inline +struct tdo_tl070wsh30_panel *to_tdo_tl070wsh30_panel(struct drm_panel *panel) +{ + return container_of(panel, struct tdo_tl070wsh30_panel, base); +} + +static int tdo_tl070wsh30_panel_unprepare(struct drm_panel *panel) +{ + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); + int err; + + if (!tdo_tl070wsh30->prepared) + return 0; + + err = mipi_dsi_dcs_set_display_off(tdo_tl070wsh30->link); + if (err < 0) + dev_err(panel->dev, "failed to set display off: %d\n", err); + + usleep_range(10000, 11000); + + err = mipi_dsi_dcs_enter_sleep_mode(tdo_tl070wsh30->link); + if (err < 0) { + dev_err(panel->dev, "failed to enter sleep mode: %d\n", err); + return err; + } + + usleep_range(10000, 11000); + + tdo_tl070wsh30->prepared = false; + + return 0; +} + +static int tdo_tl070wsh30_panel_prepare(struct drm_panel *panel) +{ + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); + int err; + + if (tdo_tl070wsh30->prepared) + return 0; + + err = mipi_dsi_dcs_exit_sleep_mode(tdo_tl070wsh30->link); + if (err < 0) { + dev_err(panel->dev, "failed to exit sleep mode: %d\n", err); + return err; + } + + msleep(200); + + err = mipi_dsi_dcs_set_display_on(tdo_tl070wsh30->link); + if (err < 0) { + dev_err(panel->dev, "failed to set display on: %d\n", err); + return err; + } + + msleep(20); + + tdo_tl070wsh30->prepared = true; + + return 0; +} + +static const struct drm_display_mode default_mode = { + .clock = 47250, + .hdisplay = 1024, + .hsync_start = 1024 + 46, + .hsync_end = 1024 + 46 + 80, + .htotal = 1024 + 46 + 80 + 100, + .vdisplay = 600, + .vsync_start = 600 + 5, + .vsync_end = 600 + 5 + 5, + .vtotal = 600 + 5 + 5 + 20, + .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC, +}; + +static int tdo_tl070wsh30_panel_get_modes(struct drm_panel *panel, + struct drm_connector *connector) +{ + struct drm_display_mode *mode; + + mode = drm_mode_duplicate(connector->dev, &default_mode); + if (!mode) { + dev_err(panel->dev, "failed to add mode %ux%ux\n", default_mode.hdisplay, + default_mode.vdisplay); + return -ENOMEM; + } + + drm_mode_set_name(mode); + + drm_mode_probed_add(connector, mode); + + connector->display_info.width_mm = 154; + connector->display_info.height_mm = 85; + connector->display_info.bpc = 8; + + return 1; +} + +static const struct drm_panel_funcs tdo_tl070wsh30_panel_funcs = { + .unprepare = tdo_tl070wsh30_panel_unprepare, + .prepare = tdo_tl070wsh30_panel_prepare, + .get_modes = tdo_tl070wsh30_panel_get_modes, +}; + +static const struct of_device_id tdo_tl070wsh30_of_match[] = { + { .compatible = "tdo,tl070wsh30", }, + { } +}; +MODULE_DEVICE_TABLE(of, tdo_tl070wsh30_of_match); + +static int tdo_tl070wsh30_panel_add(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) +{ + struct device *dev = &tdo_tl070wsh30->link->dev; + int err; + + tdo_tl070wsh30->supply = devm_regulator_get(dev, "power"); + if (IS_ERR(tdo_tl070wsh30->supply)) + return PTR_ERR(tdo_tl070wsh30->supply); + + tdo_tl070wsh30->reset_gpio = devm_gpiod_get(dev, "reset", + GPIOD_OUT_LOW); + if (IS_ERR(tdo_tl070wsh30->reset_gpio)) { + err = PTR_ERR(tdo_tl070wsh30->reset_gpio); + dev_dbg(dev, "failed to get reset gpio: %d\n", err); + return err; + } + + drm_panel_init(&tdo_tl070wsh30->base, &tdo_tl070wsh30->link->dev, + &tdo_tl070wsh30_panel_funcs, DRM_MODE_CONNECTOR_DSI); + + err = drm_panel_of_backlight(&tdo_tl070wsh30->base); + if (err) + return err; + + err = regulator_enable(tdo_tl070wsh30->supply); + if (err < 0) + return err; + + usleep_range(10000, 11000); + + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 1); + + usleep_range(10000, 11000); + + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 0); + + msleep(200); + + drm_panel_add(&tdo_tl070wsh30->base); + + return 0; +} + +static void tdo_tl070wsh30_panel_del(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) +{ + drm_panel_remove(&tdo_tl070wsh30->base); +} + +static int tdo_tl070wsh30_panel_probe(struct mipi_dsi_device *dsi) +{ + struct tdo_tl070wsh30_panel *tdo_tl070wsh30; + int err; + + dsi->lanes = 4; + dsi->format = MIPI_DSI_FMT_RGB888; + dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_LPM; + + tdo_tl070wsh30 = devm_kzalloc(&dsi->dev, sizeof(*tdo_tl070wsh30), + GFP_KERNEL); + if (!tdo_tl070wsh30) + return -ENOMEM; + + mipi_dsi_set_drvdata(dsi, tdo_tl070wsh30); + tdo_tl070wsh30->link = dsi; + + err = tdo_tl070wsh30_panel_add(tdo_tl070wsh30); + if (err < 0) + return err; + + return mipi_dsi_attach(dsi); +} + +static int tdo_tl070wsh30_panel_remove(struct mipi_dsi_device *dsi) +{ + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); + int err; + + err = drm_panel_unprepare(&tdo_tl070wsh30->base); + if (err < 0) + dev_err(&dsi->dev, "failed to unprepare panel: %d\n", err); + + err = drm_panel_disable(&tdo_tl070wsh30->base); + if (err < 0) + dev_err(&dsi->dev, "failed to disable panel: %d\n", err); + + err = mipi_dsi_detach(dsi); + if (err < 0) + dev_err(&dsi->dev, "failed to detach from DSI host: %d\n", err); + + tdo_tl070wsh30_panel_del(tdo_tl070wsh30); + + return 0; +} + +static void tdo_tl070wsh30_panel_shutdown(struct mipi_dsi_device *dsi) +{ + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); + + drm_panel_unprepare(&tdo_tl070wsh30->base); + drm_panel_disable(&tdo_tl070wsh30->base); +} + +static struct mipi_dsi_driver tdo_tl070wsh30_panel_driver = { + .driver = { + .name = "panel-tdo-tl070wsh30", + .of_match_table = tdo_tl070wsh30_of_match, + }, + .probe = tdo_tl070wsh30_panel_probe, + .remove = tdo_tl070wsh30_panel_remove, + .shutdown = tdo_tl070wsh30_panel_shutdown, +}; +module_mipi_dsi_driver(tdo_tl070wsh30_panel_driver); + +MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>"); +MODULE_DESCRIPTION("TDO TL070WSH30 panel driver"); +MODULE_LICENSE("GPL v2"); -- 2.22.0 ^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v2 3/3] drm: panel: add TDO tl070wsh30 panel driver @ 2020-09-07 11:10 ` Neil Armstrong 0 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-07 11:10 UTC (permalink / raw) To: thierry.reding, sam Cc: linux-amlogic, linux-kernel, dri-devel, Neil Armstrong This adds support for the TDO TL070WSH30 TFT-LCD panel module. The panel has a 1024×600 resolution and uses 24 bit RGB per pixel. It provides a MIPI DSI interface to the host, a built-in LED backlight and touch controller. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- drivers/gpu/drm/panel/Kconfig | 11 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c | 256 +++++++++++++++++++ 3 files changed, 268 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index 8d97d07c5871..2d488a875b99 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -433,6 +433,17 @@ config DRM_PANEL_SONY_ACX565AKM Say Y here if you want to enable support for the Sony ACX565AKM 800x600 3.5" panel (found on the Nokia N900). +config DRM_PANEL_TDO_TL070WSH30 + tristate "TDO TL070WSH30 DSI panel" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y here if you want to enable support for TDO TL070WSH30 TFT-LCD + panel module. The panel has a 1024×600 resolution and uses + 24 bit RGB per pixel. It provides a MIPI DSI interface to + the host, a built-in LED backlight and touch controller. + config DRM_PANEL_TPO_TD028TTEC1 tristate "Toppoly (TPO) TD028TTEC1 panel driver" depends on OF && SPI diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index 15a4e7752951..35ee06a1b5c2 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -45,6 +45,7 @@ obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.o +obj-$(CONFIG_DRM_PANEL_TDO_TL070WSH30) += panel-tdo-tl070wsh30.o obj-$(CONFIG_DRM_PANEL_TPO_TD028TTEC1) += panel-tpo-td028ttec1.o obj-$(CONFIG_DRM_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o diff --git a/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c new file mode 100644 index 000000000000..c7a6c2c42c52 --- /dev/null +++ b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c @@ -0,0 +1,256 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2020 BayLibre, SAS + * Author: Neil Armstrong <narmstrong@baylibre.com> + */ + +#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/regulator/consumer.h> + +#include <video/mipi_display.h> + +#include <drm/drm_crtc.h> +#include <drm/drm_device.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h> + +struct tdo_tl070wsh30_panel { + struct drm_panel base; + struct mipi_dsi_device *link; + + struct regulator *supply; + struct gpio_desc *reset_gpio; + + bool prepared; +}; + +static inline +struct tdo_tl070wsh30_panel *to_tdo_tl070wsh30_panel(struct drm_panel *panel) +{ + return container_of(panel, struct tdo_tl070wsh30_panel, base); +} + +static int tdo_tl070wsh30_panel_unprepare(struct drm_panel *panel) +{ + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); + int err; + + if (!tdo_tl070wsh30->prepared) + return 0; + + err = mipi_dsi_dcs_set_display_off(tdo_tl070wsh30->link); + if (err < 0) + dev_err(panel->dev, "failed to set display off: %d\n", err); + + usleep_range(10000, 11000); + + err = mipi_dsi_dcs_enter_sleep_mode(tdo_tl070wsh30->link); + if (err < 0) { + dev_err(panel->dev, "failed to enter sleep mode: %d\n", err); + return err; + } + + usleep_range(10000, 11000); + + tdo_tl070wsh30->prepared = false; + + return 0; +} + +static int tdo_tl070wsh30_panel_prepare(struct drm_panel *panel) +{ + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); + int err; + + if (tdo_tl070wsh30->prepared) + return 0; + + err = mipi_dsi_dcs_exit_sleep_mode(tdo_tl070wsh30->link); + if (err < 0) { + dev_err(panel->dev, "failed to exit sleep mode: %d\n", err); + return err; + } + + msleep(200); + + err = mipi_dsi_dcs_set_display_on(tdo_tl070wsh30->link); + if (err < 0) { + dev_err(panel->dev, "failed to set display on: %d\n", err); + return err; + } + + msleep(20); + + tdo_tl070wsh30->prepared = true; + + return 0; +} + +static const struct drm_display_mode default_mode = { + .clock = 47250, + .hdisplay = 1024, + .hsync_start = 1024 + 46, + .hsync_end = 1024 + 46 + 80, + .htotal = 1024 + 46 + 80 + 100, + .vdisplay = 600, + .vsync_start = 600 + 5, + .vsync_end = 600 + 5 + 5, + .vtotal = 600 + 5 + 5 + 20, + .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC, +}; + +static int tdo_tl070wsh30_panel_get_modes(struct drm_panel *panel, + struct drm_connector *connector) +{ + struct drm_display_mode *mode; + + mode = drm_mode_duplicate(connector->dev, &default_mode); + if (!mode) { + dev_err(panel->dev, "failed to add mode %ux%ux\n", default_mode.hdisplay, + default_mode.vdisplay); + return -ENOMEM; + } + + drm_mode_set_name(mode); + + drm_mode_probed_add(connector, mode); + + connector->display_info.width_mm = 154; + connector->display_info.height_mm = 85; + connector->display_info.bpc = 8; + + return 1; +} + +static const struct drm_panel_funcs tdo_tl070wsh30_panel_funcs = { + .unprepare = tdo_tl070wsh30_panel_unprepare, + .prepare = tdo_tl070wsh30_panel_prepare, + .get_modes = tdo_tl070wsh30_panel_get_modes, +}; + +static const struct of_device_id tdo_tl070wsh30_of_match[] = { + { .compatible = "tdo,tl070wsh30", }, + { } +}; +MODULE_DEVICE_TABLE(of, tdo_tl070wsh30_of_match); + +static int tdo_tl070wsh30_panel_add(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) +{ + struct device *dev = &tdo_tl070wsh30->link->dev; + int err; + + tdo_tl070wsh30->supply = devm_regulator_get(dev, "power"); + if (IS_ERR(tdo_tl070wsh30->supply)) + return PTR_ERR(tdo_tl070wsh30->supply); + + tdo_tl070wsh30->reset_gpio = devm_gpiod_get(dev, "reset", + GPIOD_OUT_LOW); + if (IS_ERR(tdo_tl070wsh30->reset_gpio)) { + err = PTR_ERR(tdo_tl070wsh30->reset_gpio); + dev_dbg(dev, "failed to get reset gpio: %d\n", err); + return err; + } + + drm_panel_init(&tdo_tl070wsh30->base, &tdo_tl070wsh30->link->dev, + &tdo_tl070wsh30_panel_funcs, DRM_MODE_CONNECTOR_DSI); + + err = drm_panel_of_backlight(&tdo_tl070wsh30->base); + if (err) + return err; + + err = regulator_enable(tdo_tl070wsh30->supply); + if (err < 0) + return err; + + usleep_range(10000, 11000); + + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 1); + + usleep_range(10000, 11000); + + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 0); + + msleep(200); + + drm_panel_add(&tdo_tl070wsh30->base); + + return 0; +} + +static void tdo_tl070wsh30_panel_del(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) +{ + drm_panel_remove(&tdo_tl070wsh30->base); +} + +static int tdo_tl070wsh30_panel_probe(struct mipi_dsi_device *dsi) +{ + struct tdo_tl070wsh30_panel *tdo_tl070wsh30; + int err; + + dsi->lanes = 4; + dsi->format = MIPI_DSI_FMT_RGB888; + dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_LPM; + + tdo_tl070wsh30 = devm_kzalloc(&dsi->dev, sizeof(*tdo_tl070wsh30), + GFP_KERNEL); + if (!tdo_tl070wsh30) + return -ENOMEM; + + mipi_dsi_set_drvdata(dsi, tdo_tl070wsh30); + tdo_tl070wsh30->link = dsi; + + err = tdo_tl070wsh30_panel_add(tdo_tl070wsh30); + if (err < 0) + return err; + + return mipi_dsi_attach(dsi); +} + +static int tdo_tl070wsh30_panel_remove(struct mipi_dsi_device *dsi) +{ + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); + int err; + + err = drm_panel_unprepare(&tdo_tl070wsh30->base); + if (err < 0) + dev_err(&dsi->dev, "failed to unprepare panel: %d\n", err); + + err = drm_panel_disable(&tdo_tl070wsh30->base); + if (err < 0) + dev_err(&dsi->dev, "failed to disable panel: %d\n", err); + + err = mipi_dsi_detach(dsi); + if (err < 0) + dev_err(&dsi->dev, "failed to detach from DSI host: %d\n", err); + + tdo_tl070wsh30_panel_del(tdo_tl070wsh30); + + return 0; +} + +static void tdo_tl070wsh30_panel_shutdown(struct mipi_dsi_device *dsi) +{ + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); + + drm_panel_unprepare(&tdo_tl070wsh30->base); + drm_panel_disable(&tdo_tl070wsh30->base); +} + +static struct mipi_dsi_driver tdo_tl070wsh30_panel_driver = { + .driver = { + .name = "panel-tdo-tl070wsh30", + .of_match_table = tdo_tl070wsh30_of_match, + }, + .probe = tdo_tl070wsh30_panel_probe, + .remove = tdo_tl070wsh30_panel_remove, + .shutdown = tdo_tl070wsh30_panel_shutdown, +}; +module_mipi_dsi_driver(tdo_tl070wsh30_panel_driver); + +MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>"); +MODULE_DESCRIPTION("TDO TL070WSH30 panel driver"); +MODULE_LICENSE("GPL v2"); -- 2.22.0 _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v2 3/3] drm: panel: add TDO tl070wsh30 panel driver @ 2020-09-07 11:10 ` Neil Armstrong 0 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-07 11:10 UTC (permalink / raw) To: thierry.reding, sam Cc: linux-amlogic, linux-kernel, dri-devel, Neil Armstrong This adds support for the TDO TL070WSH30 TFT-LCD panel module. The panel has a 1024×600 resolution and uses 24 bit RGB per pixel. It provides a MIPI DSI interface to the host, a built-in LED backlight and touch controller. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- drivers/gpu/drm/panel/Kconfig | 11 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c | 256 +++++++++++++++++++ 3 files changed, 268 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index 8d97d07c5871..2d488a875b99 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -433,6 +433,17 @@ config DRM_PANEL_SONY_ACX565AKM Say Y here if you want to enable support for the Sony ACX565AKM 800x600 3.5" panel (found on the Nokia N900). +config DRM_PANEL_TDO_TL070WSH30 + tristate "TDO TL070WSH30 DSI panel" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y here if you want to enable support for TDO TL070WSH30 TFT-LCD + panel module. The panel has a 1024×600 resolution and uses + 24 bit RGB per pixel. It provides a MIPI DSI interface to + the host, a built-in LED backlight and touch controller. + config DRM_PANEL_TPO_TD028TTEC1 tristate "Toppoly (TPO) TD028TTEC1 panel driver" depends on OF && SPI diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index 15a4e7752951..35ee06a1b5c2 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -45,6 +45,7 @@ obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.o +obj-$(CONFIG_DRM_PANEL_TDO_TL070WSH30) += panel-tdo-tl070wsh30.o obj-$(CONFIG_DRM_PANEL_TPO_TD028TTEC1) += panel-tpo-td028ttec1.o obj-$(CONFIG_DRM_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o diff --git a/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c new file mode 100644 index 000000000000..c7a6c2c42c52 --- /dev/null +++ b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c @@ -0,0 +1,256 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2020 BayLibre, SAS + * Author: Neil Armstrong <narmstrong@baylibre.com> + */ + +#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/regulator/consumer.h> + +#include <video/mipi_display.h> + +#include <drm/drm_crtc.h> +#include <drm/drm_device.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h> + +struct tdo_tl070wsh30_panel { + struct drm_panel base; + struct mipi_dsi_device *link; + + struct regulator *supply; + struct gpio_desc *reset_gpio; + + bool prepared; +}; + +static inline +struct tdo_tl070wsh30_panel *to_tdo_tl070wsh30_panel(struct drm_panel *panel) +{ + return container_of(panel, struct tdo_tl070wsh30_panel, base); +} + +static int tdo_tl070wsh30_panel_unprepare(struct drm_panel *panel) +{ + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); + int err; + + if (!tdo_tl070wsh30->prepared) + return 0; + + err = mipi_dsi_dcs_set_display_off(tdo_tl070wsh30->link); + if (err < 0) + dev_err(panel->dev, "failed to set display off: %d\n", err); + + usleep_range(10000, 11000); + + err = mipi_dsi_dcs_enter_sleep_mode(tdo_tl070wsh30->link); + if (err < 0) { + dev_err(panel->dev, "failed to enter sleep mode: %d\n", err); + return err; + } + + usleep_range(10000, 11000); + + tdo_tl070wsh30->prepared = false; + + return 0; +} + +static int tdo_tl070wsh30_panel_prepare(struct drm_panel *panel) +{ + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); + int err; + + if (tdo_tl070wsh30->prepared) + return 0; + + err = mipi_dsi_dcs_exit_sleep_mode(tdo_tl070wsh30->link); + if (err < 0) { + dev_err(panel->dev, "failed to exit sleep mode: %d\n", err); + return err; + } + + msleep(200); + + err = mipi_dsi_dcs_set_display_on(tdo_tl070wsh30->link); + if (err < 0) { + dev_err(panel->dev, "failed to set display on: %d\n", err); + return err; + } + + msleep(20); + + tdo_tl070wsh30->prepared = true; + + return 0; +} + +static const struct drm_display_mode default_mode = { + .clock = 47250, + .hdisplay = 1024, + .hsync_start = 1024 + 46, + .hsync_end = 1024 + 46 + 80, + .htotal = 1024 + 46 + 80 + 100, + .vdisplay = 600, + .vsync_start = 600 + 5, + .vsync_end = 600 + 5 + 5, + .vtotal = 600 + 5 + 5 + 20, + .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC, +}; + +static int tdo_tl070wsh30_panel_get_modes(struct drm_panel *panel, + struct drm_connector *connector) +{ + struct drm_display_mode *mode; + + mode = drm_mode_duplicate(connector->dev, &default_mode); + if (!mode) { + dev_err(panel->dev, "failed to add mode %ux%ux\n", default_mode.hdisplay, + default_mode.vdisplay); + return -ENOMEM; + } + + drm_mode_set_name(mode); + + drm_mode_probed_add(connector, mode); + + connector->display_info.width_mm = 154; + connector->display_info.height_mm = 85; + connector->display_info.bpc = 8; + + return 1; +} + +static const struct drm_panel_funcs tdo_tl070wsh30_panel_funcs = { + .unprepare = tdo_tl070wsh30_panel_unprepare, + .prepare = tdo_tl070wsh30_panel_prepare, + .get_modes = tdo_tl070wsh30_panel_get_modes, +}; + +static const struct of_device_id tdo_tl070wsh30_of_match[] = { + { .compatible = "tdo,tl070wsh30", }, + { } +}; +MODULE_DEVICE_TABLE(of, tdo_tl070wsh30_of_match); + +static int tdo_tl070wsh30_panel_add(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) +{ + struct device *dev = &tdo_tl070wsh30->link->dev; + int err; + + tdo_tl070wsh30->supply = devm_regulator_get(dev, "power"); + if (IS_ERR(tdo_tl070wsh30->supply)) + return PTR_ERR(tdo_tl070wsh30->supply); + + tdo_tl070wsh30->reset_gpio = devm_gpiod_get(dev, "reset", + GPIOD_OUT_LOW); + if (IS_ERR(tdo_tl070wsh30->reset_gpio)) { + err = PTR_ERR(tdo_tl070wsh30->reset_gpio); + dev_dbg(dev, "failed to get reset gpio: %d\n", err); + return err; + } + + drm_panel_init(&tdo_tl070wsh30->base, &tdo_tl070wsh30->link->dev, + &tdo_tl070wsh30_panel_funcs, DRM_MODE_CONNECTOR_DSI); + + err = drm_panel_of_backlight(&tdo_tl070wsh30->base); + if (err) + return err; + + err = regulator_enable(tdo_tl070wsh30->supply); + if (err < 0) + return err; + + usleep_range(10000, 11000); + + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 1); + + usleep_range(10000, 11000); + + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 0); + + msleep(200); + + drm_panel_add(&tdo_tl070wsh30->base); + + return 0; +} + +static void tdo_tl070wsh30_panel_del(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) +{ + drm_panel_remove(&tdo_tl070wsh30->base); +} + +static int tdo_tl070wsh30_panel_probe(struct mipi_dsi_device *dsi) +{ + struct tdo_tl070wsh30_panel *tdo_tl070wsh30; + int err; + + dsi->lanes = 4; + dsi->format = MIPI_DSI_FMT_RGB888; + dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_LPM; + + tdo_tl070wsh30 = devm_kzalloc(&dsi->dev, sizeof(*tdo_tl070wsh30), + GFP_KERNEL); + if (!tdo_tl070wsh30) + return -ENOMEM; + + mipi_dsi_set_drvdata(dsi, tdo_tl070wsh30); + tdo_tl070wsh30->link = dsi; + + err = tdo_tl070wsh30_panel_add(tdo_tl070wsh30); + if (err < 0) + return err; + + return mipi_dsi_attach(dsi); +} + +static int tdo_tl070wsh30_panel_remove(struct mipi_dsi_device *dsi) +{ + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); + int err; + + err = drm_panel_unprepare(&tdo_tl070wsh30->base); + if (err < 0) + dev_err(&dsi->dev, "failed to unprepare panel: %d\n", err); + + err = drm_panel_disable(&tdo_tl070wsh30->base); + if (err < 0) + dev_err(&dsi->dev, "failed to disable panel: %d\n", err); + + err = mipi_dsi_detach(dsi); + if (err < 0) + dev_err(&dsi->dev, "failed to detach from DSI host: %d\n", err); + + tdo_tl070wsh30_panel_del(tdo_tl070wsh30); + + return 0; +} + +static void tdo_tl070wsh30_panel_shutdown(struct mipi_dsi_device *dsi) +{ + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); + + drm_panel_unprepare(&tdo_tl070wsh30->base); + drm_panel_disable(&tdo_tl070wsh30->base); +} + +static struct mipi_dsi_driver tdo_tl070wsh30_panel_driver = { + .driver = { + .name = "panel-tdo-tl070wsh30", + .of_match_table = tdo_tl070wsh30_of_match, + }, + .probe = tdo_tl070wsh30_panel_probe, + .remove = tdo_tl070wsh30_panel_remove, + .shutdown = tdo_tl070wsh30_panel_shutdown, +}; +module_mipi_dsi_driver(tdo_tl070wsh30_panel_driver); + +MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>"); +MODULE_DESCRIPTION("TDO TL070WSH30 panel driver"); +MODULE_LICENSE("GPL v2"); -- 2.22.0 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 27+ messages in thread
* Re: [PATCH v2 3/3] drm: panel: add TDO tl070wsh30 panel driver 2020-09-07 11:10 ` Neil Armstrong (?) @ 2020-09-07 19:52 ` Sam Ravnborg -1 siblings, 0 replies; 27+ messages in thread From: Sam Ravnborg @ 2020-09-07 19:52 UTC (permalink / raw) To: Neil Armstrong; +Cc: thierry.reding, linux-amlogic, linux-kernel, dri-devel Hi Neil. On Mon, Sep 07, 2020 at 01:10:27PM +0200, Neil Armstrong wrote: > This adds support for the TDO TL070WSH30 TFT-LCD panel module. > The panel has a 1024×600 resolution and uses 24 bit RGB per pixel. > It provides a MIPI DSI interface to the host, a built-in LED backlight > and touch controller. Despite a nicely written driver I noticed a few things that needs to be addressed. Sam > > Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> > --- > drivers/gpu/drm/panel/Kconfig | 11 + > drivers/gpu/drm/panel/Makefile | 1 + > drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c | 256 +++++++++++++++++++ > 3 files changed, 268 insertions(+) > create mode 100644 drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c > > diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig > index 8d97d07c5871..2d488a875b99 100644 > --- a/drivers/gpu/drm/panel/Kconfig > +++ b/drivers/gpu/drm/panel/Kconfig > @@ -433,6 +433,17 @@ config DRM_PANEL_SONY_ACX565AKM > Say Y here if you want to enable support for the Sony ACX565AKM > 800x600 3.5" panel (found on the Nokia N900). > > +config DRM_PANEL_TDO_TL070WSH30 > + tristate "TDO TL070WSH30 DSI panel" > + depends on OF > + depends on DRM_MIPI_DSI > + depends on BACKLIGHT_CLASS_DEVICE > + help > + Say Y here if you want to enable support for TDO TL070WSH30 TFT-LCD > + panel module. The panel has a 1024×600 resolution and uses > + 24 bit RGB per pixel. It provides a MIPI DSI interface to > + the host, a built-in LED backlight and touch controller. > + > config DRM_PANEL_TPO_TD028TTEC1 > tristate "Toppoly (TPO) TD028TTEC1 panel driver" > depends on OF && SPI > diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile > index 15a4e7752951..35ee06a1b5c2 100644 > --- a/drivers/gpu/drm/panel/Makefile > +++ b/drivers/gpu/drm/panel/Makefile > @@ -45,6 +45,7 @@ obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o > obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o > obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o > obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.o > +obj-$(CONFIG_DRM_PANEL_TDO_TL070WSH30) += panel-tdo-tl070wsh30.o > obj-$(CONFIG_DRM_PANEL_TPO_TD028TTEC1) += panel-tpo-td028ttec1.o > obj-$(CONFIG_DRM_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o > obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o > diff --git a/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c > new file mode 100644 > index 000000000000..c7a6c2c42c52 > --- /dev/null > +++ b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c > @@ -0,0 +1,256 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (C) 2020 BayLibre, SAS > + * Author: Neil Armstrong <narmstrong@baylibre.com> > + */ > + > +#include <linux/delay.h> > +#include <linux/gpio/consumer.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/regulator/consumer.h> > + > +#include <video/mipi_display.h> > + > +#include <drm/drm_crtc.h> > +#include <drm/drm_device.h> > +#include <drm/drm_mipi_dsi.h> > +#include <drm/drm_modes.h> > +#include <drm/drm_panel.h> > + > +struct tdo_tl070wsh30_panel { > + struct drm_panel base; > + struct mipi_dsi_device *link; > + > + struct regulator *supply; > + struct gpio_desc *reset_gpio; > + > + bool prepared; > +}; > + > +static inline > +struct tdo_tl070wsh30_panel *to_tdo_tl070wsh30_panel(struct drm_panel *panel) > +{ > + return container_of(panel, struct tdo_tl070wsh30_panel, base); > +} bikeshedding - but my preference is to order the functions: prepare enable disable unprepare As this is the natural order they are used. Feel free to ignore! > + > +static int tdo_tl070wsh30_panel_unprepare(struct drm_panel *panel) > +{ > + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); > + int err; > + > + if (!tdo_tl070wsh30->prepared) > + return 0; > + > + err = mipi_dsi_dcs_set_display_off(tdo_tl070wsh30->link); > + if (err < 0) > + dev_err(panel->dev, "failed to set display off: %d\n", err); > + > + usleep_range(10000, 11000); > + > + err = mipi_dsi_dcs_enter_sleep_mode(tdo_tl070wsh30->link); > + if (err < 0) { > + dev_err(panel->dev, "failed to enter sleep mode: %d\n", err); > + return err; > + } > + > + usleep_range(10000, 11000); > + > + tdo_tl070wsh30->prepared = false; > + > + return 0; > +} > + > +static int tdo_tl070wsh30_panel_prepare(struct drm_panel *panel) > +{ > + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); > + int err; > + > + if (tdo_tl070wsh30->prepared) > + return 0; > + > + err = mipi_dsi_dcs_exit_sleep_mode(tdo_tl070wsh30->link); > + if (err < 0) { > + dev_err(panel->dev, "failed to exit sleep mode: %d\n", err); > + return err; > + } > + > + msleep(200); > + > + err = mipi_dsi_dcs_set_display_on(tdo_tl070wsh30->link); > + if (err < 0) { > + dev_err(panel->dev, "failed to set display on: %d\n", err); > + return err; > + } > + > + msleep(20); > + > + tdo_tl070wsh30->prepared = true; > + > + return 0; > +} > + > +static const struct drm_display_mode default_mode = { > + .clock = 47250, > + .hdisplay = 1024, > + .hsync_start = 1024 + 46, > + .hsync_end = 1024 + 46 + 80, > + .htotal = 1024 + 46 + 80 + 100, > + .vdisplay = 600, > + .vsync_start = 600 + 5, > + .vsync_end = 600 + 5 + 5, > + .vtotal = 600 + 5 + 5 + 20, > + .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC, > +}; > + > +static int tdo_tl070wsh30_panel_get_modes(struct drm_panel *panel, > + struct drm_connector *connector) > +{ > + struct drm_display_mode *mode; > + > + mode = drm_mode_duplicate(connector->dev, &default_mode); > + if (!mode) { > + dev_err(panel->dev, "failed to add mode %ux%ux\n", default_mode.hdisplay, > + default_mode.vdisplay); Here we often print the refresh rate too. If there is no need for the refresh rate than at least drop the extra 'x' at the end of the line. > + return -ENOMEM; > + } > + > + drm_mode_set_name(mode); > + > + drm_mode_probed_add(connector, mode); > + > + connector->display_info.width_mm = 154; > + connector->display_info.height_mm = 85; > + connector->display_info.bpc = 8; > + > + return 1; > +} > + > +static const struct drm_panel_funcs tdo_tl070wsh30_panel_funcs = { > + .unprepare = tdo_tl070wsh30_panel_unprepare, > + .prepare = tdo_tl070wsh30_panel_prepare, > + .get_modes = tdo_tl070wsh30_panel_get_modes, > +}; > + > +static const struct of_device_id tdo_tl070wsh30_of_match[] = { > + { .compatible = "tdo,tl070wsh30", }, > + { } I often recommends { /* sentinel }, but thats just to be consistent with what I see in other drivers. > +}; > +MODULE_DEVICE_TABLE(of, tdo_tl070wsh30_of_match); > + > +static int tdo_tl070wsh30_panel_add(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) > +{ > + struct device *dev = &tdo_tl070wsh30->link->dev; > + int err; > + > + tdo_tl070wsh30->supply = devm_regulator_get(dev, "power"); > + if (IS_ERR(tdo_tl070wsh30->supply)) > + return PTR_ERR(tdo_tl070wsh30->supply); > + > + tdo_tl070wsh30->reset_gpio = devm_gpiod_get(dev, "reset", > + GPIOD_OUT_LOW); > + if (IS_ERR(tdo_tl070wsh30->reset_gpio)) { > + err = PTR_ERR(tdo_tl070wsh30->reset_gpio); > + dev_dbg(dev, "failed to get reset gpio: %d\n", err); > + return err; > + } > + > + drm_panel_init(&tdo_tl070wsh30->base, &tdo_tl070wsh30->link->dev, > + &tdo_tl070wsh30_panel_funcs, DRM_MODE_CONNECTOR_DSI); > + > + err = drm_panel_of_backlight(&tdo_tl070wsh30->base); > + if (err) > + return err; > + > + err = regulator_enable(tdo_tl070wsh30->supply); > + if (err < 0) > + return err; > + > + usleep_range(10000, 11000); > + > + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 1); > + > + usleep_range(10000, 11000); > + > + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 0); > + > + msleep(200); > + It is the job of the prepare function to turn on the panel, and likewise the unprepare to turn off the panel. Please move the code above to the prepare function. > + drm_panel_add(&tdo_tl070wsh30->base); > + > + return 0; > +} > + > +static void tdo_tl070wsh30_panel_del(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) > +{ > + drm_panel_remove(&tdo_tl070wsh30->base); > +} This helper does not gain anything - call drm_panel_remove() direct. > + > +static int tdo_tl070wsh30_panel_probe(struct mipi_dsi_device *dsi) > +{ > + struct tdo_tl070wsh30_panel *tdo_tl070wsh30; > + int err; > + > + dsi->lanes = 4; > + dsi->format = MIPI_DSI_FMT_RGB888; > + dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_LPM; > + > + tdo_tl070wsh30 = devm_kzalloc(&dsi->dev, sizeof(*tdo_tl070wsh30), > + GFP_KERNEL); > + if (!tdo_tl070wsh30) > + return -ENOMEM; > + > + mipi_dsi_set_drvdata(dsi, tdo_tl070wsh30); > + tdo_tl070wsh30->link = dsi; > + > + err = tdo_tl070wsh30_panel_add(tdo_tl070wsh30); > + if (err < 0) > + return err; > + > + return mipi_dsi_attach(dsi); > +} > + > +static int tdo_tl070wsh30_panel_remove(struct mipi_dsi_device *dsi) > +{ > + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); > + int err; > + > + err = drm_panel_unprepare(&tdo_tl070wsh30->base); > + if (err < 0) > + dev_err(&dsi->dev, "failed to unprepare panel: %d\n", err); > + > + err = drm_panel_disable(&tdo_tl070wsh30->base); > + if (err < 0) > + dev_err(&dsi->dev, "failed to disable panel: %d\n", err); > + In most panel drivers we just ignore the return results here. > + err = mipi_dsi_detach(dsi); > + if (err < 0) > + dev_err(&dsi->dev, "failed to detach from DSI host: %d\n", err); > + > + tdo_tl070wsh30_panel_del(tdo_tl070wsh30); > + > + return 0; > +} > + > +static void tdo_tl070wsh30_panel_shutdown(struct mipi_dsi_device *dsi) > +{ > + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); > + > + drm_panel_unprepare(&tdo_tl070wsh30->base); > + drm_panel_disable(&tdo_tl070wsh30->base); This is the wrong order. disable before unpreapre. I am not sure what is right here - but I see some drivers that only have the disable() + unprepare() in their shutdown() method and then the remocal in their remove() function. That makes sense with this split but I have not looked too deep into it. > +} > + > +static struct mipi_dsi_driver tdo_tl070wsh30_panel_driver = { > + .driver = { > + .name = "panel-tdo-tl070wsh30", > + .of_match_table = tdo_tl070wsh30_of_match, > + }, > + .probe = tdo_tl070wsh30_panel_probe, > + .remove = tdo_tl070wsh30_panel_remove, > + .shutdown = tdo_tl070wsh30_panel_shutdown, > +}; > +module_mipi_dsi_driver(tdo_tl070wsh30_panel_driver); > + > +MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>"); > +MODULE_DESCRIPTION("TDO TL070WSH30 panel driver"); > +MODULE_LICENSE("GPL v2"); > -- > 2.22.0 > > _______________________________________________ > dri-devel mailing list > dri-devel@lists.freedesktop.org > https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v2 3/3] drm: panel: add TDO tl070wsh30 panel driver @ 2020-09-07 19:52 ` Sam Ravnborg 0 siblings, 0 replies; 27+ messages in thread From: Sam Ravnborg @ 2020-09-07 19:52 UTC (permalink / raw) To: Neil Armstrong; +Cc: linux-amlogic, thierry.reding, linux-kernel, dri-devel Hi Neil. On Mon, Sep 07, 2020 at 01:10:27PM +0200, Neil Armstrong wrote: > This adds support for the TDO TL070WSH30 TFT-LCD panel module. > The panel has a 1024×600 resolution and uses 24 bit RGB per pixel. > It provides a MIPI DSI interface to the host, a built-in LED backlight > and touch controller. Despite a nicely written driver I noticed a few things that needs to be addressed. Sam > > Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> > --- > drivers/gpu/drm/panel/Kconfig | 11 + > drivers/gpu/drm/panel/Makefile | 1 + > drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c | 256 +++++++++++++++++++ > 3 files changed, 268 insertions(+) > create mode 100644 drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c > > diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig > index 8d97d07c5871..2d488a875b99 100644 > --- a/drivers/gpu/drm/panel/Kconfig > +++ b/drivers/gpu/drm/panel/Kconfig > @@ -433,6 +433,17 @@ config DRM_PANEL_SONY_ACX565AKM > Say Y here if you want to enable support for the Sony ACX565AKM > 800x600 3.5" panel (found on the Nokia N900). > > +config DRM_PANEL_TDO_TL070WSH30 > + tristate "TDO TL070WSH30 DSI panel" > + depends on OF > + depends on DRM_MIPI_DSI > + depends on BACKLIGHT_CLASS_DEVICE > + help > + Say Y here if you want to enable support for TDO TL070WSH30 TFT-LCD > + panel module. The panel has a 1024×600 resolution and uses > + 24 bit RGB per pixel. It provides a MIPI DSI interface to > + the host, a built-in LED backlight and touch controller. > + > config DRM_PANEL_TPO_TD028TTEC1 > tristate "Toppoly (TPO) TD028TTEC1 panel driver" > depends on OF && SPI > diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile > index 15a4e7752951..35ee06a1b5c2 100644 > --- a/drivers/gpu/drm/panel/Makefile > +++ b/drivers/gpu/drm/panel/Makefile > @@ -45,6 +45,7 @@ obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o > obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o > obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o > obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.o > +obj-$(CONFIG_DRM_PANEL_TDO_TL070WSH30) += panel-tdo-tl070wsh30.o > obj-$(CONFIG_DRM_PANEL_TPO_TD028TTEC1) += panel-tpo-td028ttec1.o > obj-$(CONFIG_DRM_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o > obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o > diff --git a/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c > new file mode 100644 > index 000000000000..c7a6c2c42c52 > --- /dev/null > +++ b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c > @@ -0,0 +1,256 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (C) 2020 BayLibre, SAS > + * Author: Neil Armstrong <narmstrong@baylibre.com> > + */ > + > +#include <linux/delay.h> > +#include <linux/gpio/consumer.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/regulator/consumer.h> > + > +#include <video/mipi_display.h> > + > +#include <drm/drm_crtc.h> > +#include <drm/drm_device.h> > +#include <drm/drm_mipi_dsi.h> > +#include <drm/drm_modes.h> > +#include <drm/drm_panel.h> > + > +struct tdo_tl070wsh30_panel { > + struct drm_panel base; > + struct mipi_dsi_device *link; > + > + struct regulator *supply; > + struct gpio_desc *reset_gpio; > + > + bool prepared; > +}; > + > +static inline > +struct tdo_tl070wsh30_panel *to_tdo_tl070wsh30_panel(struct drm_panel *panel) > +{ > + return container_of(panel, struct tdo_tl070wsh30_panel, base); > +} bikeshedding - but my preference is to order the functions: prepare enable disable unprepare As this is the natural order they are used. Feel free to ignore! > + > +static int tdo_tl070wsh30_panel_unprepare(struct drm_panel *panel) > +{ > + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); > + int err; > + > + if (!tdo_tl070wsh30->prepared) > + return 0; > + > + err = mipi_dsi_dcs_set_display_off(tdo_tl070wsh30->link); > + if (err < 0) > + dev_err(panel->dev, "failed to set display off: %d\n", err); > + > + usleep_range(10000, 11000); > + > + err = mipi_dsi_dcs_enter_sleep_mode(tdo_tl070wsh30->link); > + if (err < 0) { > + dev_err(panel->dev, "failed to enter sleep mode: %d\n", err); > + return err; > + } > + > + usleep_range(10000, 11000); > + > + tdo_tl070wsh30->prepared = false; > + > + return 0; > +} > + > +static int tdo_tl070wsh30_panel_prepare(struct drm_panel *panel) > +{ > + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); > + int err; > + > + if (tdo_tl070wsh30->prepared) > + return 0; > + > + err = mipi_dsi_dcs_exit_sleep_mode(tdo_tl070wsh30->link); > + if (err < 0) { > + dev_err(panel->dev, "failed to exit sleep mode: %d\n", err); > + return err; > + } > + > + msleep(200); > + > + err = mipi_dsi_dcs_set_display_on(tdo_tl070wsh30->link); > + if (err < 0) { > + dev_err(panel->dev, "failed to set display on: %d\n", err); > + return err; > + } > + > + msleep(20); > + > + tdo_tl070wsh30->prepared = true; > + > + return 0; > +} > + > +static const struct drm_display_mode default_mode = { > + .clock = 47250, > + .hdisplay = 1024, > + .hsync_start = 1024 + 46, > + .hsync_end = 1024 + 46 + 80, > + .htotal = 1024 + 46 + 80 + 100, > + .vdisplay = 600, > + .vsync_start = 600 + 5, > + .vsync_end = 600 + 5 + 5, > + .vtotal = 600 + 5 + 5 + 20, > + .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC, > +}; > + > +static int tdo_tl070wsh30_panel_get_modes(struct drm_panel *panel, > + struct drm_connector *connector) > +{ > + struct drm_display_mode *mode; > + > + mode = drm_mode_duplicate(connector->dev, &default_mode); > + if (!mode) { > + dev_err(panel->dev, "failed to add mode %ux%ux\n", default_mode.hdisplay, > + default_mode.vdisplay); Here we often print the refresh rate too. If there is no need for the refresh rate than at least drop the extra 'x' at the end of the line. > + return -ENOMEM; > + } > + > + drm_mode_set_name(mode); > + > + drm_mode_probed_add(connector, mode); > + > + connector->display_info.width_mm = 154; > + connector->display_info.height_mm = 85; > + connector->display_info.bpc = 8; > + > + return 1; > +} > + > +static const struct drm_panel_funcs tdo_tl070wsh30_panel_funcs = { > + .unprepare = tdo_tl070wsh30_panel_unprepare, > + .prepare = tdo_tl070wsh30_panel_prepare, > + .get_modes = tdo_tl070wsh30_panel_get_modes, > +}; > + > +static const struct of_device_id tdo_tl070wsh30_of_match[] = { > + { .compatible = "tdo,tl070wsh30", }, > + { } I often recommends { /* sentinel }, but thats just to be consistent with what I see in other drivers. > +}; > +MODULE_DEVICE_TABLE(of, tdo_tl070wsh30_of_match); > + > +static int tdo_tl070wsh30_panel_add(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) > +{ > + struct device *dev = &tdo_tl070wsh30->link->dev; > + int err; > + > + tdo_tl070wsh30->supply = devm_regulator_get(dev, "power"); > + if (IS_ERR(tdo_tl070wsh30->supply)) > + return PTR_ERR(tdo_tl070wsh30->supply); > + > + tdo_tl070wsh30->reset_gpio = devm_gpiod_get(dev, "reset", > + GPIOD_OUT_LOW); > + if (IS_ERR(tdo_tl070wsh30->reset_gpio)) { > + err = PTR_ERR(tdo_tl070wsh30->reset_gpio); > + dev_dbg(dev, "failed to get reset gpio: %d\n", err); > + return err; > + } > + > + drm_panel_init(&tdo_tl070wsh30->base, &tdo_tl070wsh30->link->dev, > + &tdo_tl070wsh30_panel_funcs, DRM_MODE_CONNECTOR_DSI); > + > + err = drm_panel_of_backlight(&tdo_tl070wsh30->base); > + if (err) > + return err; > + > + err = regulator_enable(tdo_tl070wsh30->supply); > + if (err < 0) > + return err; > + > + usleep_range(10000, 11000); > + > + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 1); > + > + usleep_range(10000, 11000); > + > + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 0); > + > + msleep(200); > + It is the job of the prepare function to turn on the panel, and likewise the unprepare to turn off the panel. Please move the code above to the prepare function. > + drm_panel_add(&tdo_tl070wsh30->base); > + > + return 0; > +} > + > +static void tdo_tl070wsh30_panel_del(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) > +{ > + drm_panel_remove(&tdo_tl070wsh30->base); > +} This helper does not gain anything - call drm_panel_remove() direct. > + > +static int tdo_tl070wsh30_panel_probe(struct mipi_dsi_device *dsi) > +{ > + struct tdo_tl070wsh30_panel *tdo_tl070wsh30; > + int err; > + > + dsi->lanes = 4; > + dsi->format = MIPI_DSI_FMT_RGB888; > + dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_LPM; > + > + tdo_tl070wsh30 = devm_kzalloc(&dsi->dev, sizeof(*tdo_tl070wsh30), > + GFP_KERNEL); > + if (!tdo_tl070wsh30) > + return -ENOMEM; > + > + mipi_dsi_set_drvdata(dsi, tdo_tl070wsh30); > + tdo_tl070wsh30->link = dsi; > + > + err = tdo_tl070wsh30_panel_add(tdo_tl070wsh30); > + if (err < 0) > + return err; > + > + return mipi_dsi_attach(dsi); > +} > + > +static int tdo_tl070wsh30_panel_remove(struct mipi_dsi_device *dsi) > +{ > + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); > + int err; > + > + err = drm_panel_unprepare(&tdo_tl070wsh30->base); > + if (err < 0) > + dev_err(&dsi->dev, "failed to unprepare panel: %d\n", err); > + > + err = drm_panel_disable(&tdo_tl070wsh30->base); > + if (err < 0) > + dev_err(&dsi->dev, "failed to disable panel: %d\n", err); > + In most panel drivers we just ignore the return results here. > + err = mipi_dsi_detach(dsi); > + if (err < 0) > + dev_err(&dsi->dev, "failed to detach from DSI host: %d\n", err); > + > + tdo_tl070wsh30_panel_del(tdo_tl070wsh30); > + > + return 0; > +} > + > +static void tdo_tl070wsh30_panel_shutdown(struct mipi_dsi_device *dsi) > +{ > + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); > + > + drm_panel_unprepare(&tdo_tl070wsh30->base); > + drm_panel_disable(&tdo_tl070wsh30->base); This is the wrong order. disable before unpreapre. I am not sure what is right here - but I see some drivers that only have the disable() + unprepare() in their shutdown() method and then the remocal in their remove() function. That makes sense with this split but I have not looked too deep into it. > +} > + > +static struct mipi_dsi_driver tdo_tl070wsh30_panel_driver = { > + .driver = { > + .name = "panel-tdo-tl070wsh30", > + .of_match_table = tdo_tl070wsh30_of_match, > + }, > + .probe = tdo_tl070wsh30_panel_probe, > + .remove = tdo_tl070wsh30_panel_remove, > + .shutdown = tdo_tl070wsh30_panel_shutdown, > +}; > +module_mipi_dsi_driver(tdo_tl070wsh30_panel_driver); > + > +MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>"); > +MODULE_DESCRIPTION("TDO TL070WSH30 panel driver"); > +MODULE_LICENSE("GPL v2"); > -- > 2.22.0 > > _______________________________________________ > dri-devel mailing list > dri-devel@lists.freedesktop.org > https://lists.freedesktop.org/mailman/listinfo/dri-devel _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v2 3/3] drm: panel: add TDO tl070wsh30 panel driver @ 2020-09-07 19:52 ` Sam Ravnborg 0 siblings, 0 replies; 27+ messages in thread From: Sam Ravnborg @ 2020-09-07 19:52 UTC (permalink / raw) To: Neil Armstrong; +Cc: linux-amlogic, thierry.reding, linux-kernel, dri-devel Hi Neil. On Mon, Sep 07, 2020 at 01:10:27PM +0200, Neil Armstrong wrote: > This adds support for the TDO TL070WSH30 TFT-LCD panel module. > The panel has a 1024×600 resolution and uses 24 bit RGB per pixel. > It provides a MIPI DSI interface to the host, a built-in LED backlight > and touch controller. Despite a nicely written driver I noticed a few things that needs to be addressed. Sam > > Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> > --- > drivers/gpu/drm/panel/Kconfig | 11 + > drivers/gpu/drm/panel/Makefile | 1 + > drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c | 256 +++++++++++++++++++ > 3 files changed, 268 insertions(+) > create mode 100644 drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c > > diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig > index 8d97d07c5871..2d488a875b99 100644 > --- a/drivers/gpu/drm/panel/Kconfig > +++ b/drivers/gpu/drm/panel/Kconfig > @@ -433,6 +433,17 @@ config DRM_PANEL_SONY_ACX565AKM > Say Y here if you want to enable support for the Sony ACX565AKM > 800x600 3.5" panel (found on the Nokia N900). > > +config DRM_PANEL_TDO_TL070WSH30 > + tristate "TDO TL070WSH30 DSI panel" > + depends on OF > + depends on DRM_MIPI_DSI > + depends on BACKLIGHT_CLASS_DEVICE > + help > + Say Y here if you want to enable support for TDO TL070WSH30 TFT-LCD > + panel module. The panel has a 1024×600 resolution and uses > + 24 bit RGB per pixel. It provides a MIPI DSI interface to > + the host, a built-in LED backlight and touch controller. > + > config DRM_PANEL_TPO_TD028TTEC1 > tristate "Toppoly (TPO) TD028TTEC1 panel driver" > depends on OF && SPI > diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile > index 15a4e7752951..35ee06a1b5c2 100644 > --- a/drivers/gpu/drm/panel/Makefile > +++ b/drivers/gpu/drm/panel/Makefile > @@ -45,6 +45,7 @@ obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o > obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o > obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o > obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.o > +obj-$(CONFIG_DRM_PANEL_TDO_TL070WSH30) += panel-tdo-tl070wsh30.o > obj-$(CONFIG_DRM_PANEL_TPO_TD028TTEC1) += panel-tpo-td028ttec1.o > obj-$(CONFIG_DRM_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o > obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o > diff --git a/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c > new file mode 100644 > index 000000000000..c7a6c2c42c52 > --- /dev/null > +++ b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c > @@ -0,0 +1,256 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (C) 2020 BayLibre, SAS > + * Author: Neil Armstrong <narmstrong@baylibre.com> > + */ > + > +#include <linux/delay.h> > +#include <linux/gpio/consumer.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/regulator/consumer.h> > + > +#include <video/mipi_display.h> > + > +#include <drm/drm_crtc.h> > +#include <drm/drm_device.h> > +#include <drm/drm_mipi_dsi.h> > +#include <drm/drm_modes.h> > +#include <drm/drm_panel.h> > + > +struct tdo_tl070wsh30_panel { > + struct drm_panel base; > + struct mipi_dsi_device *link; > + > + struct regulator *supply; > + struct gpio_desc *reset_gpio; > + > + bool prepared; > +}; > + > +static inline > +struct tdo_tl070wsh30_panel *to_tdo_tl070wsh30_panel(struct drm_panel *panel) > +{ > + return container_of(panel, struct tdo_tl070wsh30_panel, base); > +} bikeshedding - but my preference is to order the functions: prepare enable disable unprepare As this is the natural order they are used. Feel free to ignore! > + > +static int tdo_tl070wsh30_panel_unprepare(struct drm_panel *panel) > +{ > + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); > + int err; > + > + if (!tdo_tl070wsh30->prepared) > + return 0; > + > + err = mipi_dsi_dcs_set_display_off(tdo_tl070wsh30->link); > + if (err < 0) > + dev_err(panel->dev, "failed to set display off: %d\n", err); > + > + usleep_range(10000, 11000); > + > + err = mipi_dsi_dcs_enter_sleep_mode(tdo_tl070wsh30->link); > + if (err < 0) { > + dev_err(panel->dev, "failed to enter sleep mode: %d\n", err); > + return err; > + } > + > + usleep_range(10000, 11000); > + > + tdo_tl070wsh30->prepared = false; > + > + return 0; > +} > + > +static int tdo_tl070wsh30_panel_prepare(struct drm_panel *panel) > +{ > + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); > + int err; > + > + if (tdo_tl070wsh30->prepared) > + return 0; > + > + err = mipi_dsi_dcs_exit_sleep_mode(tdo_tl070wsh30->link); > + if (err < 0) { > + dev_err(panel->dev, "failed to exit sleep mode: %d\n", err); > + return err; > + } > + > + msleep(200); > + > + err = mipi_dsi_dcs_set_display_on(tdo_tl070wsh30->link); > + if (err < 0) { > + dev_err(panel->dev, "failed to set display on: %d\n", err); > + return err; > + } > + > + msleep(20); > + > + tdo_tl070wsh30->prepared = true; > + > + return 0; > +} > + > +static const struct drm_display_mode default_mode = { > + .clock = 47250, > + .hdisplay = 1024, > + .hsync_start = 1024 + 46, > + .hsync_end = 1024 + 46 + 80, > + .htotal = 1024 + 46 + 80 + 100, > + .vdisplay = 600, > + .vsync_start = 600 + 5, > + .vsync_end = 600 + 5 + 5, > + .vtotal = 600 + 5 + 5 + 20, > + .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC, > +}; > + > +static int tdo_tl070wsh30_panel_get_modes(struct drm_panel *panel, > + struct drm_connector *connector) > +{ > + struct drm_display_mode *mode; > + > + mode = drm_mode_duplicate(connector->dev, &default_mode); > + if (!mode) { > + dev_err(panel->dev, "failed to add mode %ux%ux\n", default_mode.hdisplay, > + default_mode.vdisplay); Here we often print the refresh rate too. If there is no need for the refresh rate than at least drop the extra 'x' at the end of the line. > + return -ENOMEM; > + } > + > + drm_mode_set_name(mode); > + > + drm_mode_probed_add(connector, mode); > + > + connector->display_info.width_mm = 154; > + connector->display_info.height_mm = 85; > + connector->display_info.bpc = 8; > + > + return 1; > +} > + > +static const struct drm_panel_funcs tdo_tl070wsh30_panel_funcs = { > + .unprepare = tdo_tl070wsh30_panel_unprepare, > + .prepare = tdo_tl070wsh30_panel_prepare, > + .get_modes = tdo_tl070wsh30_panel_get_modes, > +}; > + > +static const struct of_device_id tdo_tl070wsh30_of_match[] = { > + { .compatible = "tdo,tl070wsh30", }, > + { } I often recommends { /* sentinel }, but thats just to be consistent with what I see in other drivers. > +}; > +MODULE_DEVICE_TABLE(of, tdo_tl070wsh30_of_match); > + > +static int tdo_tl070wsh30_panel_add(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) > +{ > + struct device *dev = &tdo_tl070wsh30->link->dev; > + int err; > + > + tdo_tl070wsh30->supply = devm_regulator_get(dev, "power"); > + if (IS_ERR(tdo_tl070wsh30->supply)) > + return PTR_ERR(tdo_tl070wsh30->supply); > + > + tdo_tl070wsh30->reset_gpio = devm_gpiod_get(dev, "reset", > + GPIOD_OUT_LOW); > + if (IS_ERR(tdo_tl070wsh30->reset_gpio)) { > + err = PTR_ERR(tdo_tl070wsh30->reset_gpio); > + dev_dbg(dev, "failed to get reset gpio: %d\n", err); > + return err; > + } > + > + drm_panel_init(&tdo_tl070wsh30->base, &tdo_tl070wsh30->link->dev, > + &tdo_tl070wsh30_panel_funcs, DRM_MODE_CONNECTOR_DSI); > + > + err = drm_panel_of_backlight(&tdo_tl070wsh30->base); > + if (err) > + return err; > + > + err = regulator_enable(tdo_tl070wsh30->supply); > + if (err < 0) > + return err; > + > + usleep_range(10000, 11000); > + > + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 1); > + > + usleep_range(10000, 11000); > + > + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 0); > + > + msleep(200); > + It is the job of the prepare function to turn on the panel, and likewise the unprepare to turn off the panel. Please move the code above to the prepare function. > + drm_panel_add(&tdo_tl070wsh30->base); > + > + return 0; > +} > + > +static void tdo_tl070wsh30_panel_del(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) > +{ > + drm_panel_remove(&tdo_tl070wsh30->base); > +} This helper does not gain anything - call drm_panel_remove() direct. > + > +static int tdo_tl070wsh30_panel_probe(struct mipi_dsi_device *dsi) > +{ > + struct tdo_tl070wsh30_panel *tdo_tl070wsh30; > + int err; > + > + dsi->lanes = 4; > + dsi->format = MIPI_DSI_FMT_RGB888; > + dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_LPM; > + > + tdo_tl070wsh30 = devm_kzalloc(&dsi->dev, sizeof(*tdo_tl070wsh30), > + GFP_KERNEL); > + if (!tdo_tl070wsh30) > + return -ENOMEM; > + > + mipi_dsi_set_drvdata(dsi, tdo_tl070wsh30); > + tdo_tl070wsh30->link = dsi; > + > + err = tdo_tl070wsh30_panel_add(tdo_tl070wsh30); > + if (err < 0) > + return err; > + > + return mipi_dsi_attach(dsi); > +} > + > +static int tdo_tl070wsh30_panel_remove(struct mipi_dsi_device *dsi) > +{ > + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); > + int err; > + > + err = drm_panel_unprepare(&tdo_tl070wsh30->base); > + if (err < 0) > + dev_err(&dsi->dev, "failed to unprepare panel: %d\n", err); > + > + err = drm_panel_disable(&tdo_tl070wsh30->base); > + if (err < 0) > + dev_err(&dsi->dev, "failed to disable panel: %d\n", err); > + In most panel drivers we just ignore the return results here. > + err = mipi_dsi_detach(dsi); > + if (err < 0) > + dev_err(&dsi->dev, "failed to detach from DSI host: %d\n", err); > + > + tdo_tl070wsh30_panel_del(tdo_tl070wsh30); > + > + return 0; > +} > + > +static void tdo_tl070wsh30_panel_shutdown(struct mipi_dsi_device *dsi) > +{ > + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); > + > + drm_panel_unprepare(&tdo_tl070wsh30->base); > + drm_panel_disable(&tdo_tl070wsh30->base); This is the wrong order. disable before unpreapre. I am not sure what is right here - but I see some drivers that only have the disable() + unprepare() in their shutdown() method and then the remocal in their remove() function. That makes sense with this split but I have not looked too deep into it. > +} > + > +static struct mipi_dsi_driver tdo_tl070wsh30_panel_driver = { > + .driver = { > + .name = "panel-tdo-tl070wsh30", > + .of_match_table = tdo_tl070wsh30_of_match, > + }, > + .probe = tdo_tl070wsh30_panel_probe, > + .remove = tdo_tl070wsh30_panel_remove, > + .shutdown = tdo_tl070wsh30_panel_shutdown, > +}; > +module_mipi_dsi_driver(tdo_tl070wsh30_panel_driver); > + > +MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>"); > +MODULE_DESCRIPTION("TDO TL070WSH30 panel driver"); > +MODULE_LICENSE("GPL v2"); > -- > 2.22.0 > > _______________________________________________ > dri-devel mailing list > dri-devel@lists.freedesktop.org > https://lists.freedesktop.org/mailman/listinfo/dri-devel _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v2 3/3] drm: panel: add TDO tl070wsh30 panel driver 2020-09-07 19:52 ` Sam Ravnborg (?) @ 2020-09-08 7:41 ` Neil Armstrong -1 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-08 7:41 UTC (permalink / raw) To: Sam Ravnborg; +Cc: thierry.reding, linux-amlogic, linux-kernel, dri-devel Hi, On 07/09/2020 21:52, Sam Ravnborg wrote: > Hi Neil. > > On Mon, Sep 07, 2020 at 01:10:27PM +0200, Neil Armstrong wrote: >> This adds support for the TDO TL070WSH30 TFT-LCD panel module. >> The panel has a 1024×600 resolution and uses 24 bit RGB per pixel. >> It provides a MIPI DSI interface to the host, a built-in LED backlight >> and touch controller. > > Despite a nicely written driver I noticed a few things that needs to be > addressed. Thanks for the review, indeed the remove/shutdown was wrong, and I aligned with panel-simple, which seems more logical. > > Sam >> >> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> >> --- >> drivers/gpu/drm/panel/Kconfig | 11 + >> drivers/gpu/drm/panel/Makefile | 1 + >> drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c | 256 +++++++++++++++++++ >> 3 files changed, 268 insertions(+) >> create mode 100644 drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c >> >> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig >> index 8d97d07c5871..2d488a875b99 100644 >> --- a/drivers/gpu/drm/panel/Kconfig >> +++ b/drivers/gpu/drm/panel/Kconfig >> @@ -433,6 +433,17 @@ config DRM_PANEL_SONY_ACX565AKM >> Say Y here if you want to enable support for the Sony ACX565AKM >> 800x600 3.5" panel (found on the Nokia N900). >> >> +config DRM_PANEL_TDO_TL070WSH30 >> + tristate "TDO TL070WSH30 DSI panel" >> + depends on OF >> + depends on DRM_MIPI_DSI >> + depends on BACKLIGHT_CLASS_DEVICE >> + help >> + Say Y here if you want to enable support for TDO TL070WSH30 TFT-LCD >> + panel module. The panel has a 1024×600 resolution and uses >> + 24 bit RGB per pixel. It provides a MIPI DSI interface to >> + the host, a built-in LED backlight and touch controller. >> + >> config DRM_PANEL_TPO_TD028TTEC1 >> tristate "Toppoly (TPO) TD028TTEC1 panel driver" >> depends on OF && SPI >> diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile >> index 15a4e7752951..35ee06a1b5c2 100644 >> --- a/drivers/gpu/drm/panel/Makefile >> +++ b/drivers/gpu/drm/panel/Makefile >> @@ -45,6 +45,7 @@ obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o >> obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o >> obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o >> obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.o >> +obj-$(CONFIG_DRM_PANEL_TDO_TL070WSH30) += panel-tdo-tl070wsh30.o >> obj-$(CONFIG_DRM_PANEL_TPO_TD028TTEC1) += panel-tpo-td028ttec1.o >> obj-$(CONFIG_DRM_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o >> obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o >> diff --git a/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c >> new file mode 100644 >> index 000000000000..c7a6c2c42c52 >> --- /dev/null >> +++ b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c >> @@ -0,0 +1,256 @@ >> +// SPDX-License-Identifier: GPL-2.0 >> +/* >> + * Copyright (C) 2020 BayLibre, SAS >> + * Author: Neil Armstrong <narmstrong@baylibre.com> >> + */ >> + >> +#include <linux/delay.h> >> +#include <linux/gpio/consumer.h> >> +#include <linux/module.h> >> +#include <linux/of.h> >> +#include <linux/regulator/consumer.h> >> + >> +#include <video/mipi_display.h> >> + >> +#include <drm/drm_crtc.h> >> +#include <drm/drm_device.h> >> +#include <drm/drm_mipi_dsi.h> >> +#include <drm/drm_modes.h> >> +#include <drm/drm_panel.h> >> + >> +struct tdo_tl070wsh30_panel { >> + struct drm_panel base; >> + struct mipi_dsi_device *link; >> + >> + struct regulator *supply; >> + struct gpio_desc *reset_gpio; >> + >> + bool prepared; >> +}; >> + >> +static inline >> +struct tdo_tl070wsh30_panel *to_tdo_tl070wsh30_panel(struct drm_panel *panel) >> +{ >> + return container_of(panel, struct tdo_tl070wsh30_panel, base); >> +} > > bikeshedding - but my preference is to order the functions: > > prepare > enable > disable > unprepare > > As this is the natural order they are used. > Feel free to ignore! Ack, prepare before unprepare looks better ! > >> + >> +static int tdo_tl070wsh30_panel_unprepare(struct drm_panel *panel) >> +{ >> + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); >> + int err; >> + >> + if (!tdo_tl070wsh30->prepared) >> + return 0; >> + >> + err = mipi_dsi_dcs_set_display_off(tdo_tl070wsh30->link); >> + if (err < 0) >> + dev_err(panel->dev, "failed to set display off: %d\n", err); >> + >> + usleep_range(10000, 11000); >> + >> + err = mipi_dsi_dcs_enter_sleep_mode(tdo_tl070wsh30->link); >> + if (err < 0) { >> + dev_err(panel->dev, "failed to enter sleep mode: %d\n", err); >> + return err; >> + } >> + >> + usleep_range(10000, 11000); >> + >> + tdo_tl070wsh30->prepared = false; >> + >> + return 0; >> +} >> + >> +static int tdo_tl070wsh30_panel_prepare(struct drm_panel *panel) >> +{ >> + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); >> + int err; >> + >> + if (tdo_tl070wsh30->prepared) >> + return 0; >> + >> + err = mipi_dsi_dcs_exit_sleep_mode(tdo_tl070wsh30->link); >> + if (err < 0) { >> + dev_err(panel->dev, "failed to exit sleep mode: %d\n", err); >> + return err; >> + } >> + >> + msleep(200); >> + >> + err = mipi_dsi_dcs_set_display_on(tdo_tl070wsh30->link); >> + if (err < 0) { >> + dev_err(panel->dev, "failed to set display on: %d\n", err); >> + return err; >> + } >> + >> + msleep(20); >> + >> + tdo_tl070wsh30->prepared = true; >> + >> + return 0; >> +} >> + >> +static const struct drm_display_mode default_mode = { >> + .clock = 47250, >> + .hdisplay = 1024, >> + .hsync_start = 1024 + 46, >> + .hsync_end = 1024 + 46 + 80, >> + .htotal = 1024 + 46 + 80 + 100, >> + .vdisplay = 600, >> + .vsync_start = 600 + 5, >> + .vsync_end = 600 + 5 + 5, >> + .vtotal = 600 + 5 + 5 + 20, >> + .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC, >> +}; >> + >> +static int tdo_tl070wsh30_panel_get_modes(struct drm_panel *panel, >> + struct drm_connector *connector) >> +{ >> + struct drm_display_mode *mode; >> + >> + mode = drm_mode_duplicate(connector->dev, &default_mode); >> + if (!mode) { >> + dev_err(panel->dev, "failed to add mode %ux%ux\n", default_mode.hdisplay, >> + default_mode.vdisplay); > Here we often print the refresh rate too. > If there is no need for the refresh rate than at least drop the extra > 'x' at the end of the line. I forgot to remove it after vrefresh removal, but I'll prefer adding back drm_mode_vrefresh() and the refresh. > >> + return -ENOMEM; >> + } >> + >> + drm_mode_set_name(mode); >> + >> + drm_mode_probed_add(connector, mode); >> + >> + connector->display_info.width_mm = 154; >> + connector->display_info.height_mm = 85; >> + connector->display_info.bpc = 8; >> + >> + return 1; >> +} >> + >> +static const struct drm_panel_funcs tdo_tl070wsh30_panel_funcs = { >> + .unprepare = tdo_tl070wsh30_panel_unprepare, >> + .prepare = tdo_tl070wsh30_panel_prepare, >> + .get_modes = tdo_tl070wsh30_panel_get_modes, >> +}; >> + >> +static const struct of_device_id tdo_tl070wsh30_of_match[] = { >> + { .compatible = "tdo,tl070wsh30", }, >> + { } > I often recommends > { /* sentinel }, > > but thats just to be consistent with what I see in other drivers. Let it be consistent. > >> +}; >> +MODULE_DEVICE_TABLE(of, tdo_tl070wsh30_of_match); >> + >> +static int tdo_tl070wsh30_panel_add(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) >> +{ >> + struct device *dev = &tdo_tl070wsh30->link->dev; >> + int err; >> + >> + tdo_tl070wsh30->supply = devm_regulator_get(dev, "power"); >> + if (IS_ERR(tdo_tl070wsh30->supply)) >> + return PTR_ERR(tdo_tl070wsh30->supply); >> + >> + tdo_tl070wsh30->reset_gpio = devm_gpiod_get(dev, "reset", >> + GPIOD_OUT_LOW); >> + if (IS_ERR(tdo_tl070wsh30->reset_gpio)) { >> + err = PTR_ERR(tdo_tl070wsh30->reset_gpio); >> + dev_dbg(dev, "failed to get reset gpio: %d\n", err); >> + return err; >> + } >> + >> + drm_panel_init(&tdo_tl070wsh30->base, &tdo_tl070wsh30->link->dev, >> + &tdo_tl070wsh30_panel_funcs, DRM_MODE_CONNECTOR_DSI); >> + >> + err = drm_panel_of_backlight(&tdo_tl070wsh30->base); >> + if (err) >> + return err; > > > >> + >> + err = regulator_enable(tdo_tl070wsh30->supply); >> + if (err < 0) >> + return err; >> + >> + usleep_range(10000, 11000); >> + >> + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 1); >> + >> + usleep_range(10000, 11000); >> + >> + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 0); >> + >> + msleep(200); >> + > > It is the job of the prepare function to turn on the panel, > and likewise the unprepare to turn off the panel. > Please move the code above to the prepare function. Moved > > >> + drm_panel_add(&tdo_tl070wsh30->base); >> + >> + return 0; >> +} >> + >> +static void tdo_tl070wsh30_panel_del(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) >> +{ >> + drm_panel_remove(&tdo_tl070wsh30->base); >> +} > This helper does not gain anything - call drm_panel_remove() direct. Removed > >> + >> +static int tdo_tl070wsh30_panel_probe(struct mipi_dsi_device *dsi) >> +{ >> + struct tdo_tl070wsh30_panel *tdo_tl070wsh30; >> + int err; >> + >> + dsi->lanes = 4; >> + dsi->format = MIPI_DSI_FMT_RGB888; >> + dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_LPM; >> + >> + tdo_tl070wsh30 = devm_kzalloc(&dsi->dev, sizeof(*tdo_tl070wsh30), >> + GFP_KERNEL); >> + if (!tdo_tl070wsh30) >> + return -ENOMEM; >> + >> + mipi_dsi_set_drvdata(dsi, tdo_tl070wsh30); >> + tdo_tl070wsh30->link = dsi; >> + >> + err = tdo_tl070wsh30_panel_add(tdo_tl070wsh30); >> + if (err < 0) >> + return err; >> + >> + return mipi_dsi_attach(dsi); >> +} >> + >> +static int tdo_tl070wsh30_panel_remove(struct mipi_dsi_device *dsi) >> +{ >> + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); >> + int err; >> + >> + err = drm_panel_unprepare(&tdo_tl070wsh30->base); >> + if (err < 0) >> + dev_err(&dsi->dev, "failed to unprepare panel: %d\n", err); >> + >> + err = drm_panel_disable(&tdo_tl070wsh30->base); >> + if (err < 0) >> + dev_err(&dsi->dev, "failed to disable panel: %d\n", err); >> + > In most panel drivers we just ignore the return results here. Ok > >> + err = mipi_dsi_detach(dsi); >> + if (err < 0) >> + dev_err(&dsi->dev, "failed to detach from DSI host: %d\n", err); >> + >> + tdo_tl070wsh30_panel_del(tdo_tl070wsh30); >> + >> + return 0; >> +} >> + >> +static void tdo_tl070wsh30_panel_shutdown(struct mipi_dsi_device *dsi) >> +{ >> + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); >> + >> + drm_panel_unprepare(&tdo_tl070wsh30->base); >> + drm_panel_disable(&tdo_tl070wsh30->base); > This is the wrong order. disable before unpreapre. > > > I am not sure what is right here - but I see some drivers that only have > the disable() + unprepare() in their shutdown() method and then the > remocal in their remove() function. > That makes sense with this split but I have not looked too deep into it. No prob, I aligned with panel-simple here. > >> +} >> + >> +static struct mipi_dsi_driver tdo_tl070wsh30_panel_driver = { >> + .driver = { >> + .name = "panel-tdo-tl070wsh30", >> + .of_match_table = tdo_tl070wsh30_of_match, >> + }, >> + .probe = tdo_tl070wsh30_panel_probe, >> + .remove = tdo_tl070wsh30_panel_remove, >> + .shutdown = tdo_tl070wsh30_panel_shutdown, >> +}; >> +module_mipi_dsi_driver(tdo_tl070wsh30_panel_driver); >> + >> +MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>"); >> +MODULE_DESCRIPTION("TDO TL070WSH30 panel driver"); >> +MODULE_LICENSE("GPL v2"); >> -- >> 2.22.0 >> >> _______________________________________________ >> dri-devel mailing list >> dri-devel@lists.freedesktop.org >> https://lists.freedesktop.org/mailman/listinfo/dri-devel Thanks, Neil ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v2 3/3] drm: panel: add TDO tl070wsh30 panel driver @ 2020-09-08 7:41 ` Neil Armstrong 0 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-08 7:41 UTC (permalink / raw) To: Sam Ravnborg; +Cc: linux-amlogic, thierry.reding, linux-kernel, dri-devel Hi, On 07/09/2020 21:52, Sam Ravnborg wrote: > Hi Neil. > > On Mon, Sep 07, 2020 at 01:10:27PM +0200, Neil Armstrong wrote: >> This adds support for the TDO TL070WSH30 TFT-LCD panel module. >> The panel has a 1024×600 resolution and uses 24 bit RGB per pixel. >> It provides a MIPI DSI interface to the host, a built-in LED backlight >> and touch controller. > > Despite a nicely written driver I noticed a few things that needs to be > addressed. Thanks for the review, indeed the remove/shutdown was wrong, and I aligned with panel-simple, which seems more logical. > > Sam >> >> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> >> --- >> drivers/gpu/drm/panel/Kconfig | 11 + >> drivers/gpu/drm/panel/Makefile | 1 + >> drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c | 256 +++++++++++++++++++ >> 3 files changed, 268 insertions(+) >> create mode 100644 drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c >> >> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig >> index 8d97d07c5871..2d488a875b99 100644 >> --- a/drivers/gpu/drm/panel/Kconfig >> +++ b/drivers/gpu/drm/panel/Kconfig >> @@ -433,6 +433,17 @@ config DRM_PANEL_SONY_ACX565AKM >> Say Y here if you want to enable support for the Sony ACX565AKM >> 800x600 3.5" panel (found on the Nokia N900). >> >> +config DRM_PANEL_TDO_TL070WSH30 >> + tristate "TDO TL070WSH30 DSI panel" >> + depends on OF >> + depends on DRM_MIPI_DSI >> + depends on BACKLIGHT_CLASS_DEVICE >> + help >> + Say Y here if you want to enable support for TDO TL070WSH30 TFT-LCD >> + panel module. The panel has a 1024×600 resolution and uses >> + 24 bit RGB per pixel. It provides a MIPI DSI interface to >> + the host, a built-in LED backlight and touch controller. >> + >> config DRM_PANEL_TPO_TD028TTEC1 >> tristate "Toppoly (TPO) TD028TTEC1 panel driver" >> depends on OF && SPI >> diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile >> index 15a4e7752951..35ee06a1b5c2 100644 >> --- a/drivers/gpu/drm/panel/Makefile >> +++ b/drivers/gpu/drm/panel/Makefile >> @@ -45,6 +45,7 @@ obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o >> obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o >> obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o >> obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.o >> +obj-$(CONFIG_DRM_PANEL_TDO_TL070WSH30) += panel-tdo-tl070wsh30.o >> obj-$(CONFIG_DRM_PANEL_TPO_TD028TTEC1) += panel-tpo-td028ttec1.o >> obj-$(CONFIG_DRM_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o >> obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o >> diff --git a/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c >> new file mode 100644 >> index 000000000000..c7a6c2c42c52 >> --- /dev/null >> +++ b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c >> @@ -0,0 +1,256 @@ >> +// SPDX-License-Identifier: GPL-2.0 >> +/* >> + * Copyright (C) 2020 BayLibre, SAS >> + * Author: Neil Armstrong <narmstrong@baylibre.com> >> + */ >> + >> +#include <linux/delay.h> >> +#include <linux/gpio/consumer.h> >> +#include <linux/module.h> >> +#include <linux/of.h> >> +#include <linux/regulator/consumer.h> >> + >> +#include <video/mipi_display.h> >> + >> +#include <drm/drm_crtc.h> >> +#include <drm/drm_device.h> >> +#include <drm/drm_mipi_dsi.h> >> +#include <drm/drm_modes.h> >> +#include <drm/drm_panel.h> >> + >> +struct tdo_tl070wsh30_panel { >> + struct drm_panel base; >> + struct mipi_dsi_device *link; >> + >> + struct regulator *supply; >> + struct gpio_desc *reset_gpio; >> + >> + bool prepared; >> +}; >> + >> +static inline >> +struct tdo_tl070wsh30_panel *to_tdo_tl070wsh30_panel(struct drm_panel *panel) >> +{ >> + return container_of(panel, struct tdo_tl070wsh30_panel, base); >> +} > > bikeshedding - but my preference is to order the functions: > > prepare > enable > disable > unprepare > > As this is the natural order they are used. > Feel free to ignore! Ack, prepare before unprepare looks better ! > >> + >> +static int tdo_tl070wsh30_panel_unprepare(struct drm_panel *panel) >> +{ >> + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); >> + int err; >> + >> + if (!tdo_tl070wsh30->prepared) >> + return 0; >> + >> + err = mipi_dsi_dcs_set_display_off(tdo_tl070wsh30->link); >> + if (err < 0) >> + dev_err(panel->dev, "failed to set display off: %d\n", err); >> + >> + usleep_range(10000, 11000); >> + >> + err = mipi_dsi_dcs_enter_sleep_mode(tdo_tl070wsh30->link); >> + if (err < 0) { >> + dev_err(panel->dev, "failed to enter sleep mode: %d\n", err); >> + return err; >> + } >> + >> + usleep_range(10000, 11000); >> + >> + tdo_tl070wsh30->prepared = false; >> + >> + return 0; >> +} >> + >> +static int tdo_tl070wsh30_panel_prepare(struct drm_panel *panel) >> +{ >> + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); >> + int err; >> + >> + if (tdo_tl070wsh30->prepared) >> + return 0; >> + >> + err = mipi_dsi_dcs_exit_sleep_mode(tdo_tl070wsh30->link); >> + if (err < 0) { >> + dev_err(panel->dev, "failed to exit sleep mode: %d\n", err); >> + return err; >> + } >> + >> + msleep(200); >> + >> + err = mipi_dsi_dcs_set_display_on(tdo_tl070wsh30->link); >> + if (err < 0) { >> + dev_err(panel->dev, "failed to set display on: %d\n", err); >> + return err; >> + } >> + >> + msleep(20); >> + >> + tdo_tl070wsh30->prepared = true; >> + >> + return 0; >> +} >> + >> +static const struct drm_display_mode default_mode = { >> + .clock = 47250, >> + .hdisplay = 1024, >> + .hsync_start = 1024 + 46, >> + .hsync_end = 1024 + 46 + 80, >> + .htotal = 1024 + 46 + 80 + 100, >> + .vdisplay = 600, >> + .vsync_start = 600 + 5, >> + .vsync_end = 600 + 5 + 5, >> + .vtotal = 600 + 5 + 5 + 20, >> + .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC, >> +}; >> + >> +static int tdo_tl070wsh30_panel_get_modes(struct drm_panel *panel, >> + struct drm_connector *connector) >> +{ >> + struct drm_display_mode *mode; >> + >> + mode = drm_mode_duplicate(connector->dev, &default_mode); >> + if (!mode) { >> + dev_err(panel->dev, "failed to add mode %ux%ux\n", default_mode.hdisplay, >> + default_mode.vdisplay); > Here we often print the refresh rate too. > If there is no need for the refresh rate than at least drop the extra > 'x' at the end of the line. I forgot to remove it after vrefresh removal, but I'll prefer adding back drm_mode_vrefresh() and the refresh. > >> + return -ENOMEM; >> + } >> + >> + drm_mode_set_name(mode); >> + >> + drm_mode_probed_add(connector, mode); >> + >> + connector->display_info.width_mm = 154; >> + connector->display_info.height_mm = 85; >> + connector->display_info.bpc = 8; >> + >> + return 1; >> +} >> + >> +static const struct drm_panel_funcs tdo_tl070wsh30_panel_funcs = { >> + .unprepare = tdo_tl070wsh30_panel_unprepare, >> + .prepare = tdo_tl070wsh30_panel_prepare, >> + .get_modes = tdo_tl070wsh30_panel_get_modes, >> +}; >> + >> +static const struct of_device_id tdo_tl070wsh30_of_match[] = { >> + { .compatible = "tdo,tl070wsh30", }, >> + { } > I often recommends > { /* sentinel }, > > but thats just to be consistent with what I see in other drivers. Let it be consistent. > >> +}; >> +MODULE_DEVICE_TABLE(of, tdo_tl070wsh30_of_match); >> + >> +static int tdo_tl070wsh30_panel_add(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) >> +{ >> + struct device *dev = &tdo_tl070wsh30->link->dev; >> + int err; >> + >> + tdo_tl070wsh30->supply = devm_regulator_get(dev, "power"); >> + if (IS_ERR(tdo_tl070wsh30->supply)) >> + return PTR_ERR(tdo_tl070wsh30->supply); >> + >> + tdo_tl070wsh30->reset_gpio = devm_gpiod_get(dev, "reset", >> + GPIOD_OUT_LOW); >> + if (IS_ERR(tdo_tl070wsh30->reset_gpio)) { >> + err = PTR_ERR(tdo_tl070wsh30->reset_gpio); >> + dev_dbg(dev, "failed to get reset gpio: %d\n", err); >> + return err; >> + } >> + >> + drm_panel_init(&tdo_tl070wsh30->base, &tdo_tl070wsh30->link->dev, >> + &tdo_tl070wsh30_panel_funcs, DRM_MODE_CONNECTOR_DSI); >> + >> + err = drm_panel_of_backlight(&tdo_tl070wsh30->base); >> + if (err) >> + return err; > > > >> + >> + err = regulator_enable(tdo_tl070wsh30->supply); >> + if (err < 0) >> + return err; >> + >> + usleep_range(10000, 11000); >> + >> + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 1); >> + >> + usleep_range(10000, 11000); >> + >> + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 0); >> + >> + msleep(200); >> + > > It is the job of the prepare function to turn on the panel, > and likewise the unprepare to turn off the panel. > Please move the code above to the prepare function. Moved > > >> + drm_panel_add(&tdo_tl070wsh30->base); >> + >> + return 0; >> +} >> + >> +static void tdo_tl070wsh30_panel_del(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) >> +{ >> + drm_panel_remove(&tdo_tl070wsh30->base); >> +} > This helper does not gain anything - call drm_panel_remove() direct. Removed > >> + >> +static int tdo_tl070wsh30_panel_probe(struct mipi_dsi_device *dsi) >> +{ >> + struct tdo_tl070wsh30_panel *tdo_tl070wsh30; >> + int err; >> + >> + dsi->lanes = 4; >> + dsi->format = MIPI_DSI_FMT_RGB888; >> + dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_LPM; >> + >> + tdo_tl070wsh30 = devm_kzalloc(&dsi->dev, sizeof(*tdo_tl070wsh30), >> + GFP_KERNEL); >> + if (!tdo_tl070wsh30) >> + return -ENOMEM; >> + >> + mipi_dsi_set_drvdata(dsi, tdo_tl070wsh30); >> + tdo_tl070wsh30->link = dsi; >> + >> + err = tdo_tl070wsh30_panel_add(tdo_tl070wsh30); >> + if (err < 0) >> + return err; >> + >> + return mipi_dsi_attach(dsi); >> +} >> + >> +static int tdo_tl070wsh30_panel_remove(struct mipi_dsi_device *dsi) >> +{ >> + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); >> + int err; >> + >> + err = drm_panel_unprepare(&tdo_tl070wsh30->base); >> + if (err < 0) >> + dev_err(&dsi->dev, "failed to unprepare panel: %d\n", err); >> + >> + err = drm_panel_disable(&tdo_tl070wsh30->base); >> + if (err < 0) >> + dev_err(&dsi->dev, "failed to disable panel: %d\n", err); >> + > In most panel drivers we just ignore the return results here. Ok > >> + err = mipi_dsi_detach(dsi); >> + if (err < 0) >> + dev_err(&dsi->dev, "failed to detach from DSI host: %d\n", err); >> + >> + tdo_tl070wsh30_panel_del(tdo_tl070wsh30); >> + >> + return 0; >> +} >> + >> +static void tdo_tl070wsh30_panel_shutdown(struct mipi_dsi_device *dsi) >> +{ >> + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); >> + >> + drm_panel_unprepare(&tdo_tl070wsh30->base); >> + drm_panel_disable(&tdo_tl070wsh30->base); > This is the wrong order. disable before unpreapre. > > > I am not sure what is right here - but I see some drivers that only have > the disable() + unprepare() in their shutdown() method and then the > remocal in their remove() function. > That makes sense with this split but I have not looked too deep into it. No prob, I aligned with panel-simple here. > >> +} >> + >> +static struct mipi_dsi_driver tdo_tl070wsh30_panel_driver = { >> + .driver = { >> + .name = "panel-tdo-tl070wsh30", >> + .of_match_table = tdo_tl070wsh30_of_match, >> + }, >> + .probe = tdo_tl070wsh30_panel_probe, >> + .remove = tdo_tl070wsh30_panel_remove, >> + .shutdown = tdo_tl070wsh30_panel_shutdown, >> +}; >> +module_mipi_dsi_driver(tdo_tl070wsh30_panel_driver); >> + >> +MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>"); >> +MODULE_DESCRIPTION("TDO TL070WSH30 panel driver"); >> +MODULE_LICENSE("GPL v2"); >> -- >> 2.22.0 >> >> _______________________________________________ >> dri-devel mailing list >> dri-devel@lists.freedesktop.org >> https://lists.freedesktop.org/mailman/listinfo/dri-devel Thanks, Neil _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v2 3/3] drm: panel: add TDO tl070wsh30 panel driver @ 2020-09-08 7:41 ` Neil Armstrong 0 siblings, 0 replies; 27+ messages in thread From: Neil Armstrong @ 2020-09-08 7:41 UTC (permalink / raw) To: Sam Ravnborg; +Cc: linux-amlogic, thierry.reding, linux-kernel, dri-devel Hi, On 07/09/2020 21:52, Sam Ravnborg wrote: > Hi Neil. > > On Mon, Sep 07, 2020 at 01:10:27PM +0200, Neil Armstrong wrote: >> This adds support for the TDO TL070WSH30 TFT-LCD panel module. >> The panel has a 1024×600 resolution and uses 24 bit RGB per pixel. >> It provides a MIPI DSI interface to the host, a built-in LED backlight >> and touch controller. > > Despite a nicely written driver I noticed a few things that needs to be > addressed. Thanks for the review, indeed the remove/shutdown was wrong, and I aligned with panel-simple, which seems more logical. > > Sam >> >> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> >> --- >> drivers/gpu/drm/panel/Kconfig | 11 + >> drivers/gpu/drm/panel/Makefile | 1 + >> drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c | 256 +++++++++++++++++++ >> 3 files changed, 268 insertions(+) >> create mode 100644 drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c >> >> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig >> index 8d97d07c5871..2d488a875b99 100644 >> --- a/drivers/gpu/drm/panel/Kconfig >> +++ b/drivers/gpu/drm/panel/Kconfig >> @@ -433,6 +433,17 @@ config DRM_PANEL_SONY_ACX565AKM >> Say Y here if you want to enable support for the Sony ACX565AKM >> 800x600 3.5" panel (found on the Nokia N900). >> >> +config DRM_PANEL_TDO_TL070WSH30 >> + tristate "TDO TL070WSH30 DSI panel" >> + depends on OF >> + depends on DRM_MIPI_DSI >> + depends on BACKLIGHT_CLASS_DEVICE >> + help >> + Say Y here if you want to enable support for TDO TL070WSH30 TFT-LCD >> + panel module. The panel has a 1024×600 resolution and uses >> + 24 bit RGB per pixel. It provides a MIPI DSI interface to >> + the host, a built-in LED backlight and touch controller. >> + >> config DRM_PANEL_TPO_TD028TTEC1 >> tristate "Toppoly (TPO) TD028TTEC1 panel driver" >> depends on OF && SPI >> diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile >> index 15a4e7752951..35ee06a1b5c2 100644 >> --- a/drivers/gpu/drm/panel/Makefile >> +++ b/drivers/gpu/drm/panel/Makefile >> @@ -45,6 +45,7 @@ obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o >> obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o >> obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o >> obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.o >> +obj-$(CONFIG_DRM_PANEL_TDO_TL070WSH30) += panel-tdo-tl070wsh30.o >> obj-$(CONFIG_DRM_PANEL_TPO_TD028TTEC1) += panel-tpo-td028ttec1.o >> obj-$(CONFIG_DRM_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o >> obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o >> diff --git a/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c >> new file mode 100644 >> index 000000000000..c7a6c2c42c52 >> --- /dev/null >> +++ b/drivers/gpu/drm/panel/panel-tdo-tl070wsh30.c >> @@ -0,0 +1,256 @@ >> +// SPDX-License-Identifier: GPL-2.0 >> +/* >> + * Copyright (C) 2020 BayLibre, SAS >> + * Author: Neil Armstrong <narmstrong@baylibre.com> >> + */ >> + >> +#include <linux/delay.h> >> +#include <linux/gpio/consumer.h> >> +#include <linux/module.h> >> +#include <linux/of.h> >> +#include <linux/regulator/consumer.h> >> + >> +#include <video/mipi_display.h> >> + >> +#include <drm/drm_crtc.h> >> +#include <drm/drm_device.h> >> +#include <drm/drm_mipi_dsi.h> >> +#include <drm/drm_modes.h> >> +#include <drm/drm_panel.h> >> + >> +struct tdo_tl070wsh30_panel { >> + struct drm_panel base; >> + struct mipi_dsi_device *link; >> + >> + struct regulator *supply; >> + struct gpio_desc *reset_gpio; >> + >> + bool prepared; >> +}; >> + >> +static inline >> +struct tdo_tl070wsh30_panel *to_tdo_tl070wsh30_panel(struct drm_panel *panel) >> +{ >> + return container_of(panel, struct tdo_tl070wsh30_panel, base); >> +} > > bikeshedding - but my preference is to order the functions: > > prepare > enable > disable > unprepare > > As this is the natural order they are used. > Feel free to ignore! Ack, prepare before unprepare looks better ! > >> + >> +static int tdo_tl070wsh30_panel_unprepare(struct drm_panel *panel) >> +{ >> + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); >> + int err; >> + >> + if (!tdo_tl070wsh30->prepared) >> + return 0; >> + >> + err = mipi_dsi_dcs_set_display_off(tdo_tl070wsh30->link); >> + if (err < 0) >> + dev_err(panel->dev, "failed to set display off: %d\n", err); >> + >> + usleep_range(10000, 11000); >> + >> + err = mipi_dsi_dcs_enter_sleep_mode(tdo_tl070wsh30->link); >> + if (err < 0) { >> + dev_err(panel->dev, "failed to enter sleep mode: %d\n", err); >> + return err; >> + } >> + >> + usleep_range(10000, 11000); >> + >> + tdo_tl070wsh30->prepared = false; >> + >> + return 0; >> +} >> + >> +static int tdo_tl070wsh30_panel_prepare(struct drm_panel *panel) >> +{ >> + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = to_tdo_tl070wsh30_panel(panel); >> + int err; >> + >> + if (tdo_tl070wsh30->prepared) >> + return 0; >> + >> + err = mipi_dsi_dcs_exit_sleep_mode(tdo_tl070wsh30->link); >> + if (err < 0) { >> + dev_err(panel->dev, "failed to exit sleep mode: %d\n", err); >> + return err; >> + } >> + >> + msleep(200); >> + >> + err = mipi_dsi_dcs_set_display_on(tdo_tl070wsh30->link); >> + if (err < 0) { >> + dev_err(panel->dev, "failed to set display on: %d\n", err); >> + return err; >> + } >> + >> + msleep(20); >> + >> + tdo_tl070wsh30->prepared = true; >> + >> + return 0; >> +} >> + >> +static const struct drm_display_mode default_mode = { >> + .clock = 47250, >> + .hdisplay = 1024, >> + .hsync_start = 1024 + 46, >> + .hsync_end = 1024 + 46 + 80, >> + .htotal = 1024 + 46 + 80 + 100, >> + .vdisplay = 600, >> + .vsync_start = 600 + 5, >> + .vsync_end = 600 + 5 + 5, >> + .vtotal = 600 + 5 + 5 + 20, >> + .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC, >> +}; >> + >> +static int tdo_tl070wsh30_panel_get_modes(struct drm_panel *panel, >> + struct drm_connector *connector) >> +{ >> + struct drm_display_mode *mode; >> + >> + mode = drm_mode_duplicate(connector->dev, &default_mode); >> + if (!mode) { >> + dev_err(panel->dev, "failed to add mode %ux%ux\n", default_mode.hdisplay, >> + default_mode.vdisplay); > Here we often print the refresh rate too. > If there is no need for the refresh rate than at least drop the extra > 'x' at the end of the line. I forgot to remove it after vrefresh removal, but I'll prefer adding back drm_mode_vrefresh() and the refresh. > >> + return -ENOMEM; >> + } >> + >> + drm_mode_set_name(mode); >> + >> + drm_mode_probed_add(connector, mode); >> + >> + connector->display_info.width_mm = 154; >> + connector->display_info.height_mm = 85; >> + connector->display_info.bpc = 8; >> + >> + return 1; >> +} >> + >> +static const struct drm_panel_funcs tdo_tl070wsh30_panel_funcs = { >> + .unprepare = tdo_tl070wsh30_panel_unprepare, >> + .prepare = tdo_tl070wsh30_panel_prepare, >> + .get_modes = tdo_tl070wsh30_panel_get_modes, >> +}; >> + >> +static const struct of_device_id tdo_tl070wsh30_of_match[] = { >> + { .compatible = "tdo,tl070wsh30", }, >> + { } > I often recommends > { /* sentinel }, > > but thats just to be consistent with what I see in other drivers. Let it be consistent. > >> +}; >> +MODULE_DEVICE_TABLE(of, tdo_tl070wsh30_of_match); >> + >> +static int tdo_tl070wsh30_panel_add(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) >> +{ >> + struct device *dev = &tdo_tl070wsh30->link->dev; >> + int err; >> + >> + tdo_tl070wsh30->supply = devm_regulator_get(dev, "power"); >> + if (IS_ERR(tdo_tl070wsh30->supply)) >> + return PTR_ERR(tdo_tl070wsh30->supply); >> + >> + tdo_tl070wsh30->reset_gpio = devm_gpiod_get(dev, "reset", >> + GPIOD_OUT_LOW); >> + if (IS_ERR(tdo_tl070wsh30->reset_gpio)) { >> + err = PTR_ERR(tdo_tl070wsh30->reset_gpio); >> + dev_dbg(dev, "failed to get reset gpio: %d\n", err); >> + return err; >> + } >> + >> + drm_panel_init(&tdo_tl070wsh30->base, &tdo_tl070wsh30->link->dev, >> + &tdo_tl070wsh30_panel_funcs, DRM_MODE_CONNECTOR_DSI); >> + >> + err = drm_panel_of_backlight(&tdo_tl070wsh30->base); >> + if (err) >> + return err; > > > >> + >> + err = regulator_enable(tdo_tl070wsh30->supply); >> + if (err < 0) >> + return err; >> + >> + usleep_range(10000, 11000); >> + >> + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 1); >> + >> + usleep_range(10000, 11000); >> + >> + gpiod_set_value_cansleep(tdo_tl070wsh30->reset_gpio, 0); >> + >> + msleep(200); >> + > > It is the job of the prepare function to turn on the panel, > and likewise the unprepare to turn off the panel. > Please move the code above to the prepare function. Moved > > >> + drm_panel_add(&tdo_tl070wsh30->base); >> + >> + return 0; >> +} >> + >> +static void tdo_tl070wsh30_panel_del(struct tdo_tl070wsh30_panel *tdo_tl070wsh30) >> +{ >> + drm_panel_remove(&tdo_tl070wsh30->base); >> +} > This helper does not gain anything - call drm_panel_remove() direct. Removed > >> + >> +static int tdo_tl070wsh30_panel_probe(struct mipi_dsi_device *dsi) >> +{ >> + struct tdo_tl070wsh30_panel *tdo_tl070wsh30; >> + int err; >> + >> + dsi->lanes = 4; >> + dsi->format = MIPI_DSI_FMT_RGB888; >> + dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_LPM; >> + >> + tdo_tl070wsh30 = devm_kzalloc(&dsi->dev, sizeof(*tdo_tl070wsh30), >> + GFP_KERNEL); >> + if (!tdo_tl070wsh30) >> + return -ENOMEM; >> + >> + mipi_dsi_set_drvdata(dsi, tdo_tl070wsh30); >> + tdo_tl070wsh30->link = dsi; >> + >> + err = tdo_tl070wsh30_panel_add(tdo_tl070wsh30); >> + if (err < 0) >> + return err; >> + >> + return mipi_dsi_attach(dsi); >> +} >> + >> +static int tdo_tl070wsh30_panel_remove(struct mipi_dsi_device *dsi) >> +{ >> + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); >> + int err; >> + >> + err = drm_panel_unprepare(&tdo_tl070wsh30->base); >> + if (err < 0) >> + dev_err(&dsi->dev, "failed to unprepare panel: %d\n", err); >> + >> + err = drm_panel_disable(&tdo_tl070wsh30->base); >> + if (err < 0) >> + dev_err(&dsi->dev, "failed to disable panel: %d\n", err); >> + > In most panel drivers we just ignore the return results here. Ok > >> + err = mipi_dsi_detach(dsi); >> + if (err < 0) >> + dev_err(&dsi->dev, "failed to detach from DSI host: %d\n", err); >> + >> + tdo_tl070wsh30_panel_del(tdo_tl070wsh30); >> + >> + return 0; >> +} >> + >> +static void tdo_tl070wsh30_panel_shutdown(struct mipi_dsi_device *dsi) >> +{ >> + struct tdo_tl070wsh30_panel *tdo_tl070wsh30 = mipi_dsi_get_drvdata(dsi); >> + >> + drm_panel_unprepare(&tdo_tl070wsh30->base); >> + drm_panel_disable(&tdo_tl070wsh30->base); > This is the wrong order. disable before unpreapre. > > > I am not sure what is right here - but I see some drivers that only have > the disable() + unprepare() in their shutdown() method and then the > remocal in their remove() function. > That makes sense with this split but I have not looked too deep into it. No prob, I aligned with panel-simple here. > >> +} >> + >> +static struct mipi_dsi_driver tdo_tl070wsh30_panel_driver = { >> + .driver = { >> + .name = "panel-tdo-tl070wsh30", >> + .of_match_table = tdo_tl070wsh30_of_match, >> + }, >> + .probe = tdo_tl070wsh30_panel_probe, >> + .remove = tdo_tl070wsh30_panel_remove, >> + .shutdown = tdo_tl070wsh30_panel_shutdown, >> +}; >> +module_mipi_dsi_driver(tdo_tl070wsh30_panel_driver); >> + >> +MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>"); >> +MODULE_DESCRIPTION("TDO TL070WSH30 panel driver"); >> +MODULE_LICENSE("GPL v2"); >> -- >> 2.22.0 >> >> _______________________________________________ >> dri-devel mailing list >> dri-devel@lists.freedesktop.org >> https://lists.freedesktop.org/mailman/listinfo/dri-devel Thanks, Neil _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 27+ messages in thread
end of thread, other threads:[~2020-09-08 7:41 UTC | newest] Thread overview: 27+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2020-09-07 11:10 [PATCH 0/3] drm: panel: add support for TDO tl070wsh30 panel Neil Armstrong 2020-09-07 11:10 ` Neil Armstrong 2020-09-07 11:10 ` Neil Armstrong 2020-09-07 11:10 ` [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add Shanghai Top Display Optolelectronics vendor prefix Neil Armstrong 2020-09-07 11:10 ` Neil Armstrong 2020-09-07 11:10 ` Neil Armstrong 2020-09-07 11:10 ` [PATCH v2 2/3] dt-bindings: display: panel: add TDO tl070wsh30 DSI panel bindings Neil Armstrong 2020-09-07 11:10 ` Neil Armstrong 2020-09-07 11:10 ` Neil Armstrong 2020-09-07 11:45 ` Sam Ravnborg 2020-09-07 11:45 ` Sam Ravnborg 2020-09-07 11:45 ` Sam Ravnborg 2020-09-07 13:24 ` Neil Armstrong 2020-09-07 13:24 ` Neil Armstrong 2020-09-07 13:24 ` Neil Armstrong 2020-09-07 19:24 ` Sam Ravnborg 2020-09-07 19:24 ` Sam Ravnborg 2020-09-07 19:24 ` Sam Ravnborg 2020-09-07 11:10 ` [PATCH v2 3/3] drm: panel: add TDO tl070wsh30 panel driver Neil Armstrong 2020-09-07 11:10 ` Neil Armstrong 2020-09-07 11:10 ` Neil Armstrong 2020-09-07 19:52 ` Sam Ravnborg 2020-09-07 19:52 ` Sam Ravnborg 2020-09-07 19:52 ` Sam Ravnborg 2020-09-08 7:41 ` Neil Armstrong 2020-09-08 7:41 ` Neil Armstrong 2020-09-08 7:41 ` Neil Armstrong
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.