[PATCH v2 00/11] usb: musb: adding multi instance support

[PATCH v2 00/11] usb: musb: adding multi instance support

[Ajay Kumar Gupta]

Hi,

This series of patches adds,
a) Multi instances support in musb driver
b) DT support for musb_dsps glue layer
c) DT support for NOP transceiver

AM33xx and TI81xx has dual musb controller and has two usb PHY of same type.
This patch series uses 'phandle' based API devm_usb_get_phy_by_phandle() to
get the PHY of same type. This API support is being added by Kishon's patch
discussed at [1]

The series applies to linux-omap (master branch)
	+ Vaibhav baseport patches on his tree at [3]
	+ Kishon's multi phy patches on Felipe's branch 'xceiv'
	+ Kishon's patch on phandle at [1]
	+ AM33xx musb glue compile and bugfix patches at [4], [5], [6] and [7]
	+ Damodar's recent patch at [2] 

and have been tested on Beaglebone board.

1. http://marc.info/?l=linux-usb&m=134070369306112&w=2
2. http://marc.info/?l=linux-usb&m=134200284230689&w=2
3. https://github.com/hvaibhav/am335x-linux/commits/am335x-upstream-staging
4. http://marc.info/?l=linux-usb&m=134131746111637&w=2
5. http://marc.info/?l=linux-usb&m=134131746411639&w=2
6. http://marc.info/?l=linux-usb&m=134062716011251&w=2
7. http://marc.info/?l=linux-usb&m=134061179405213&w=2

Changes from v1:
	- Defined musb_ida to manage core ids based on Felipe's comment
	  in [PATCH 01/11]
Thanks,
Ajay

Ajay Kumar Gupta (11):
  usb: musb: add musb->id to identify core instance
  usb: musb: kill global and static for multi instance
  usb: musb: am335x: add support for dual instance
  usb: otg: nop: add support for multiple tranceiver
  usb: musb: dsps: add dt support
  arm/dts: am33xx: Add dt data for usbss
  usb: otg: nop: add dt support
  arm/dts: am33xx: add dt data for usb nop phy
  usb: musb: dsps: remove explicit NOP device creation
  usb: musb: dsps: get the PHY using phandle api
  arm/dts: am33xx: add phy phandle to usbss

 .../devicetree/bindings/usb/am33xx-usb.txt         |   19 ++
 arch/arm/boot/dts/am33xx.dtsi                      |   21 +++
 arch/arm/mach-omap2/board-omap3evm.c               |    2 +-
 drivers/usb/musb/am35x.c                           |   46 +++--
 drivers/usb/musb/blackfin.c                        |   30 +++-
 drivers/usb/musb/da8xx.c                           |   38 +++--
 drivers/usb/musb/davinci.c                         |   40 +++--
 drivers/usb/musb/musb_core.c                       |   47 ++++--
 drivers/usb/musb/musb_core.h                       |    8 +
 drivers/usb/musb/musb_debugfs.c                    |   14 +-
 drivers/usb/musb/musb_dsps.c                       |  191 ++++++++++++++------
 drivers/usb/musb/omap2430.c                        |   26 ++-
 drivers/usb/musb/tusb6010.c                        |   32 +++-
 drivers/usb/musb/ux500.c                           |   33 +++-
 drivers/usb/otg/nop-usb-xceiv.c                    |   32 +++-
 include/linux/usb/otg.h                            |    9 +-
 16 files changed, 425 insertions(+), 163 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/usb/am33xx-usb.txt

[PATCH v2 01/11] usb: musb: add musb->id to identify core instance

[Ajay Kumar Gupta]

Added 'id' field within 'struct musb' which can be used to determine
the current instance of musb controller.

Also defined musb_ida in musb_core.c to manage the core ids.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
---
 drivers/usb/musb/am35x.c     |   42 ++++++++++++++++++++++++++++--------------
 drivers/usb/musb/blackfin.c  |   26 ++++++++++++++++++++------
 drivers/usb/musb/da8xx.c     |   34 ++++++++++++++++++++++++----------
 drivers/usb/musb/davinci.c   |   34 ++++++++++++++++++++++++----------
 drivers/usb/musb/musb_core.c |   31 +++++++++++++++++++++++++++++++
 drivers/usb/musb/musb_core.h |    4 ++++
 drivers/usb/musb/musb_dsps.c |   25 ++++++++++++++++++-------
 drivers/usb/musb/omap2430.c  |   26 ++++++++++++++++++++------
 drivers/usb/musb/tusb6010.c  |   26 ++++++++++++++++++++------
 drivers/usb/musb/ux500.c     |   33 +++++++++++++++++++++++----------
 10 files changed, 212 insertions(+), 69 deletions(-)

diff --git a/drivers/usb/musb/am35x.c b/drivers/usb/musb/am35x.c
index 7a95ab8..01203eb 100644
--- a/drivers/usb/musb/am35x.c
+++ b/drivers/usb/musb/am35x.c
@@ -468,6 +468,7 @@ static int __devinit am35x_probe(struct platform_device *pdev)
 	struct clk			*clk;
 
 	int				ret = -ENOMEM;
+	int				musbid;
 
 	glue = kzalloc(sizeof(*glue), GFP_KERNEL);
 	if (!glue) {
@@ -475,38 +476,47 @@ static int __devinit am35x_probe(struct platform_device *pdev)
 		goto err0;
 	}
 
-	musb = platform_device_alloc("musb-hdrc", -1);
+	/* get the musb id */
+	musbid = musb_get_id(&pdev->dev, GFP_KERNEL);
+	if (musbid < 0) {
+		dev_err(&pdev->dev, "failed to allocate musb id\n");
+		ret = -ENOMEM;
+		goto err1;
+	}
+
+	musb = platform_device_alloc("musb-hdrc", musbid);
 	if (!musb) {
 		dev_err(&pdev->dev, "failed to allocate musb device\n");
-		goto err1;
+		goto err2;
 	}
 
 	phy_clk = clk_get(&pdev->dev, "fck");
 	if (IS_ERR(phy_clk)) {
 		dev_err(&pdev->dev, "failed to get PHY clock\n");
 		ret = PTR_ERR(phy_clk);
-		goto err2;
+		goto err3;
 	}
 
 	clk = clk_get(&pdev->dev, "ick");
 	if (IS_ERR(clk)) {
 		dev_err(&pdev->dev, "failed to get clock\n");
 		ret = PTR_ERR(clk);
-		goto err3;
+		goto err4;
 	}
 
 	ret = clk_enable(phy_clk);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to enable PHY clock\n");
-		goto err4;
+		goto err5;
 	}
 
 	ret = clk_enable(clk);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to enable clock\n");
-		goto err5;
+		goto err6;
 	}
 
+	musb->id			= musbid;
 	musb->dev.parent		= &pdev->dev;
 	musb->dev.dma_mask		= &am35x_dmamask;
 	musb->dev.coherent_dma_mask	= am35x_dmamask;
@@ -524,38 +534,41 @@ static int __devinit am35x_probe(struct platform_device *pdev)
 			pdev->num_resources);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to add resources\n");
-		goto err6;
+		goto err7;
 	}
 
 	ret = platform_device_add_data(musb, pdata, sizeof(*pdata));
 	if (ret) {
 		dev_err(&pdev->dev, "failed to add platform_data\n");
-		goto err6;
+		goto err7;
 	}
 
 	ret = platform_device_add(musb);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to register musb device\n");
-		goto err6;
+		goto err7;
 	}
 
 	return 0;
 
-err6:
+err7:
 	clk_disable(clk);
 
-err5:
+err6:
 	clk_disable(phy_clk);
 
-err4:
+err5:
 	clk_put(clk);
 
-err3:
+err4:
 	clk_put(phy_clk);
 
-err2:
+err3:
 	platform_device_put(musb);
 
+err2:
+	musb_put_id(&pdev->dev, musbid);
+
 err1:
 	kfree(glue);
 
@@ -567,6 +580,7 @@ static int __devexit am35x_remove(struct platform_device *pdev)
 {
 	struct am35x_glue	*glue = platform_get_drvdata(pdev);
 
+	musb_put_id(&pdev->dev, glue->musb->id);
 	platform_device_del(glue->musb);
 	platform_device_put(glue->musb);
 	clk_disable(glue->clk);
diff --git a/drivers/usb/musb/blackfin.c b/drivers/usb/musb/blackfin.c
index 428e6aa..c848b82 100644
--- a/drivers/usb/musb/blackfin.c
+++ b/drivers/usb/musb/blackfin.c
@@ -471,6 +471,7 @@ static int __devinit bfin_probe(struct platform_device *pdev)
 	struct bfin_glue		*glue;
 
 	int				ret = -ENOMEM;
+	int				musbid;
 
 	glue = kzalloc(sizeof(*glue), GFP_KERNEL);
 	if (!glue) {
@@ -478,12 +479,21 @@ static int __devinit bfin_probe(struct platform_device *pdev)
 		goto err0;
 	}
 
-	musb = platform_device_alloc("musb-hdrc", -1);
+	/* get the musb id */
+	musbid = musb_get_id(&pdev->dev, GFP_KERNEL);
+	if (musbid < 0) {
+		dev_err(&pdev->dev, "failed to allocate musb id\n");
+		ret = -ENOMEM;
+		goto err1;
+	}
+
+	musb = platform_device_alloc("musb-hdrc", musbid);
 	if (!musb) {
 		dev_err(&pdev->dev, "failed to allocate musb device\n");
-		goto err1;
+		goto err2;
 	}
 
+	musb->id			= musbid;
 	musb->dev.parent		= &pdev->dev;
 	musb->dev.dma_mask		= &bfin_dmamask;
 	musb->dev.coherent_dma_mask	= bfin_dmamask;
@@ -499,26 +509,29 @@ static int __devinit bfin_probe(struct platform_device *pdev)
 			pdev->num_resources);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to add resources\n");
-		goto err2;
+		goto err3;
 	}
 
 	ret = platform_device_add_data(musb, pdata, sizeof(*pdata));
 	if (ret) {
 		dev_err(&pdev->dev, "failed to add platform_data\n");
-		goto err2;
+		goto err3;
 	}
 
 	ret = platform_device_add(musb);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to register musb device\n");
-		goto err2;
+		goto err3;
 	}
 
 	return 0;
 
-err2:
+err3:
 	platform_device_put(musb);
 
+err2:
+	musb_put_id(&pdev->dev, musbid);
+
 err1:
 	kfree(glue);
 
@@ -530,6 +543,7 @@ static int __devexit bfin_remove(struct platform_device *pdev)
 {
 	struct bfin_glue		*glue = platform_get_drvdata(pdev);
 
+	musb_put_id(&pdev->dev, glue->musb->id);
 	platform_device_del(glue->musb);
 	platform_device_put(glue->musb);
 	kfree(glue);
diff --git a/drivers/usb/musb/da8xx.c b/drivers/usb/musb/da8xx.c
index 0f9fcec..cebd9d7 100644
--- a/drivers/usb/musb/da8xx.c
+++ b/drivers/usb/musb/da8xx.c
@@ -489,6 +489,7 @@ static int __devinit da8xx_probe(struct platform_device *pdev)
 	struct clk			*clk;
 
 	int				ret = -ENOMEM;
+	int				musbid;
 
 	glue = kzalloc(sizeof(*glue), GFP_KERNEL);
 	if (!glue) {
@@ -496,25 +497,34 @@ static int __devinit da8xx_probe(struct platform_device *pdev)
 		goto err0;
 	}
 
-	musb = platform_device_alloc("musb-hdrc", -1);
+	/* get the musb id */
+	musbid = musb_get_id(&pdev->dev, GFP_KERNEL);
+	if (musbid < 0) {
+		dev_err(&pdev->dev, "failed to allocate musb id\n");
+		ret = -ENOMEM;
+		goto err1;
+	}
+
+	musb = platform_device_alloc("musb-hdrc", musbid);
 	if (!musb) {
 		dev_err(&pdev->dev, "failed to allocate musb device\n");
-		goto err1;
+		goto err2;
 	}
 
 	clk = clk_get(&pdev->dev, "usb20");
 	if (IS_ERR(clk)) {
 		dev_err(&pdev->dev, "failed to get clock\n");
 		ret = PTR_ERR(clk);
-		goto err2;
+		goto err3;
 	}
 
 	ret = clk_enable(clk);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to enable clock\n");
-		goto err3;
+		goto err4;
 	}
 
+	musb->id			= musbid;
 	musb->dev.parent		= &pdev->dev;
 	musb->dev.dma_mask		= &da8xx_dmamask;
 	musb->dev.coherent_dma_mask	= da8xx_dmamask;
@@ -531,32 +541,35 @@ static int __devinit da8xx_probe(struct platform_device *pdev)
 			pdev->num_resources);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to add resources\n");
-		goto err4;
+		goto err5;
 	}
 
 	ret = platform_device_add_data(musb, pdata, sizeof(*pdata));
 	if (ret) {
 		dev_err(&pdev->dev, "failed to add platform_data\n");
-		goto err4;
+		goto err5;
 	}
 
 	ret = platform_device_add(musb);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to register musb device\n");
-		goto err4;
+		goto err5;
 	}
 
 	return 0;
 
-err4:
+err5:
 	clk_disable(clk);
 
-err3:
+err4:
 	clk_put(clk);
 
-err2:
+err3:
 	platform_device_put(musb);
 
+err2:
+	musb_put_id(&pdev->dev, musbid);
+
 err1:
 	kfree(glue);
 
@@ -568,6 +581,7 @@ static int __devexit da8xx_remove(struct platform_device *pdev)
 {
 	struct da8xx_glue		*glue = platform_get_drvdata(pdev);
 
+	musb_put_id(&pdev->dev, glue->musb->id);
 	platform_device_del(glue->musb);
 	platform_device_put(glue->musb);
 	clk_disable(glue->clk);
diff --git a/drivers/usb/musb/davinci.c b/drivers/usb/musb/davinci.c
index 472c8b4..3f094f2 100644
--- a/drivers/usb/musb/davinci.c
+++ b/drivers/usb/musb/davinci.c
@@ -523,6 +523,7 @@ static int __devinit davinci_probe(struct platform_device *pdev)
 	struct clk			*clk;
 
 	int				ret = -ENOMEM;
+	int				musbid;
 
 	glue = kzalloc(sizeof(*glue), GFP_KERNEL);
 	if (!glue) {
@@ -530,25 +531,34 @@ static int __devinit davinci_probe(struct platform_device *pdev)
 		goto err0;
 	}
 
-	musb = platform_device_alloc("musb-hdrc", -1);
+	/* get the musb id */
+	musbid = musb_get_id(&pdev->dev, GFP_KERNEL);
+	if (musbid < 0) {
+		dev_err(&pdev->dev, "failed to allocate musb id\n");
+		ret = -ENOMEM;
+		goto err1;
+	}
+
+	musb = platform_device_alloc("musb-hdrc", musbid);
 	if (!musb) {
 		dev_err(&pdev->dev, "failed to allocate musb device\n");
-		goto err1;
+		goto err2;
 	}
 
 	clk = clk_get(&pdev->dev, "usb");
 	if (IS_ERR(clk)) {
 		dev_err(&pdev->dev, "failed to get clock\n");
 		ret = PTR_ERR(clk);
-		goto err2;
+		goto err3;
 	}
 
 	ret = clk_enable(clk);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to enable clock\n");
-		goto err3;
+		goto err4;
 	}
 
+	musb->id			= musbid;
 	musb->dev.parent		= &pdev->dev;
 	musb->dev.dma_mask		= &davinci_dmamask;
 	musb->dev.coherent_dma_mask	= davinci_dmamask;
@@ -565,32 +575,35 @@ static int __devinit davinci_probe(struct platform_device *pdev)
 			pdev->num_resources);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to add resources\n");
-		goto err4;
+		goto err5;
 	}
 
 	ret = platform_device_add_data(musb, pdata, sizeof(*pdata));
 	if (ret) {
 		dev_err(&pdev->dev, "failed to add platform_data\n");
-		goto err4;
+		goto err5;
 	}
 
 	ret = platform_device_add(musb);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to register musb device\n");
-		goto err4;
+		goto err5;
 	}
 
 	return 0;
 
-err4:
+err5:
 	clk_disable(clk);
 
-err3:
+err4:
 	clk_put(clk);
 
-err2:
+err3:
 	platform_device_put(musb);
 
+err2:
+	musb_put_id(&pdev->dev, musbid);
+
 err1:
 	kfree(glue);
 
@@ -602,6 +615,7 @@ static int __devexit davinci_remove(struct platform_device *pdev)
 {
 	struct davinci_glue		*glue = platform_get_drvdata(pdev);
 
+	musb_put_id(&pdev->dev, glue->musb->id);
 	platform_device_del(glue->musb);
 	platform_device_put(glue->musb);
 	clk_disable(glue->clk);
diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c
index 89d1871..3e09984 100644
--- a/drivers/usb/musb/musb_core.c
+++ b/drivers/usb/musb/musb_core.c
@@ -99,6 +99,7 @@
 #include <linux/prefetch.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
+#include <linux/idr.h>
 
 #include "musb_core.h"
 
@@ -114,6 +115,7 @@
 
 #define MUSB_DRIVER_NAME "musb-hdrc"
 const char musb_driver_name[] = MUSB_DRIVER_NAME;
+static DEFINE_IDA(musb_ida);
 
 MODULE_DESCRIPTION(DRIVER_INFO);
 MODULE_AUTHOR(DRIVER_AUTHOR);
@@ -130,6 +132,33 @@ static inline struct musb *dev_to_musb(struct device *dev)
 
 /*-------------------------------------------------------------------------*/
 
+int musb_get_id(struct device *dev, gfp_t gfp_mask)
+{
+	int ret;
+	int id;
+
+	ret = ida_pre_get(&musb_ida, gfp_mask);
+	if (!ret) {
+		dev_err(dev, "failed to reserve resource for id\n");
+		return -ENOMEM;
+	}
+
+	ret = ida_get_new(&musb_ida, &id);
+	if (ret < 0) {
+		dev_err(dev, "failed to allocate a new id\n");
+		return ret;
+	}
+
+	return id;
+}
+
+void musb_put_id(struct device *dev, int id)
+{
+
+	dev_dbg(dev, "removing id %d\n", id);
+	ida_remove(&musb_ida, id);
+}
+
 #ifndef CONFIG_BLACKFIN
 static int musb_ulpi_read(struct usb_phy *phy, u32 offset)
 {
@@ -1867,6 +1896,7 @@ musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl)
 	int			status;
 	struct musb		*musb;
 	struct musb_hdrc_platform_data *plat = dev->platform_data;
+	struct platform_device *pdev = to_platform_device(dev);
 
 	/* The driver might handle more features than the board; OK.
 	 * Fail when the board needs a feature that's not enabled.
@@ -1889,6 +1919,7 @@ musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl)
 	pm_runtime_enable(musb->controller);
 
 	spin_lock_init(&musb->lock);
+	musb->id = pdev->id;
 	musb->board_mode = plat->mode;
 	musb->board_set_power = plat->set_power;
 	musb->min_power = plat->min_power;
diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h
index 51bd7b2..69ed141 100644
--- a/drivers/usb/musb/musb_core.h
+++ b/drivers/usb/musb/musb_core.h
@@ -450,6 +450,8 @@ struct musb {
 #ifdef MUSB_CONFIG_PROC_FS
 	struct proc_dir_entry *proc_entry;
 #endif
+	/* id for multiple musb instances */
+	u8			id;
 };
 
 static inline struct musb *gadget_to_musb(struct usb_gadget *g)
@@ -530,6 +532,8 @@ extern const char musb_driver_name[];
 
 extern void musb_start(struct musb *musb);
 extern void musb_stop(struct musb *musb);
+extern int musb_get_id(struct device *dev, gfp_t gfp_mask);
+extern void musb_put_id(struct device *dev, int id);
 
 extern void musb_write_fifo(struct musb_hw_ep *ep, u16 len, const u8 *src);
 extern void musb_read_fifo(struct musb_hw_ep *ep, u16 len, u8 *dst);
diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c
index 46b07cc..2174699 100644
--- a/drivers/usb/musb/musb_dsps.c
+++ b/drivers/usb/musb/musb_dsps.c
@@ -494,7 +494,7 @@ static int __devinit dsps_create_musb_pdev(struct dsps_glue *glue, u8 id)
 	struct resource *res;
 	struct resource	resources[2];
 	char res_name[10];
-	int ret;
+	int ret, musbid;
 
 	/* get memory resource for usb control register */
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 2 * id + 2);
@@ -534,14 +534,22 @@ static int __devinit dsps_create_musb_pdev(struct dsps_glue *glue, u8 id)
 	resources[1] = *res;
 	resources[1].name = "mc";
 
+	/* get the musb id */
+	musbid = musb_get_id(dev, GFP_KERNEL);
+	if (musbid < 0) {
+		dev_err(dev, "failed to allocate musb id\n");
+		ret = -ENOMEM;
+		goto err0;
+	}
 	/* allocate the child platform device */
-	musb = platform_device_alloc("musb-hdrc", -1);
+	musb = platform_device_alloc("musb-hdrc", musbid);
 	if (!musb) {
 		dev_err(dev, "failed to allocate musb device\n");
 		ret = -ENOMEM;
-		goto err0;
+		goto err1;
 	}
 
+	musb->id			= musbid;
 	musb->dev.parent		= dev;
 	musb->dev.dma_mask		= &musb_dmamask;
 	musb->dev.coherent_dma_mask	= musb_dmamask;
@@ -553,31 +561,34 @@ static int __devinit dsps_create_musb_pdev(struct dsps_glue *glue, u8 id)
 	ret = platform_device_add_resources(musb, resources, 2);
 	if (ret) {
 		dev_err(dev, "failed to add resources\n");
-		goto err1;
+		goto err2;
 	}
 
 	ret = platform_device_add_data(musb, pdata, sizeof(*pdata));
 	if (ret) {
 		dev_err(dev, "failed to add platform_data\n");
-		goto err1;
+		goto err2;
 	}
 
 	ret = platform_device_add(musb);
 	if (ret) {
 		dev_err(dev, "failed to register musb device\n");
-		goto err1;
+		goto err2;
 	}
 
 	return 0;
 
-err1:
+err2:
 	platform_device_put(musb);
+err1:
+	musb_put_id(dev, musbid);
 err0:
 	return ret;
 }
 
 static void __devexit dsps_delete_musb_pdev(struct dsps_glue *glue)
 {
+	musb_put_id(glue->dev, glue->musb->id);
 	platform_device_del(glue->musb);
 	platform_device_put(glue->musb);
 }
diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
index 5fdb9da..759752b 100644
--- a/drivers/usb/musb/omap2430.c
+++ b/drivers/usb/musb/omap2430.c
@@ -441,6 +441,7 @@ static int __devinit omap2430_probe(struct platform_device *pdev)
 	struct platform_device		*musb;
 	struct omap2430_glue		*glue;
 	int				ret = -ENOMEM;
+	int				musbid;
 
 	glue = devm_kzalloc(&pdev->dev, sizeof(*glue), GFP_KERNEL);
 	if (!glue) {
@@ -448,12 +449,21 @@ static int __devinit omap2430_probe(struct platform_device *pdev)
 		goto err0;
 	}
 
-	musb = platform_device_alloc("musb-hdrc", -1);
+	/* get the musb id */
+	musbid = musb_get_id(&pdev->dev, GFP_KERNEL);
+	if (musbid < 0) {
+		dev_err(&pdev->dev, "failed to allocate musb id\n");
+		ret = -ENOMEM;
+		goto err0;
+	}
+
+	musb = platform_device_alloc("musb-hdrc", musbid);
 	if (!musb) {
 		dev_err(&pdev->dev, "failed to allocate musb device\n");
-		goto err0;
+		goto err1;
 	}
 
+	musb->id			= musbid;
 	musb->dev.parent		= &pdev->dev;
 	musb->dev.dma_mask		= &omap2430_dmamask;
 	musb->dev.coherent_dma_mask	= omap2430_dmamask;
@@ -478,13 +488,13 @@ static int __devinit omap2430_probe(struct platform_device *pdev)
 			pdev->num_resources);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to add resources\n");
-		goto err1;
+		goto err2;
 	}
 
 	ret = platform_device_add_data(musb, pdata, sizeof(*pdata));
 	if (ret) {
 		dev_err(&pdev->dev, "failed to add platform_data\n");
-		goto err1;
+		goto err2;
 	}
 
 	pm_runtime_enable(&pdev->dev);
@@ -492,14 +502,17 @@ static int __devinit omap2430_probe(struct platform_device *pdev)
 	ret = platform_device_add(musb);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to register musb device\n");
-		goto err1;
+		goto err2;
 	}
 
 	return 0;
 
-err1:
+err2:
 	platform_device_put(musb);
 
+err1:
+	musb_put_id(&pdev->dev, musbid);
+
 err0:
 	return ret;
 }
@@ -509,6 +522,7 @@ static int __devexit omap2430_remove(struct platform_device *pdev)
 	struct omap2430_glue		*glue = platform_get_drvdata(pdev);
 
 	cancel_work_sync(&glue->omap_musb_mailbox_work);
+	musb_put_id(&pdev->dev, glue->musb->id);
 	platform_device_del(glue->musb);
 	platform_device_put(glue->musb);
 
diff --git a/drivers/usb/musb/tusb6010.c b/drivers/usb/musb/tusb6010.c
index 1a1bd9c..64a0e95 100644
--- a/drivers/usb/musb/tusb6010.c
+++ b/drivers/usb/musb/tusb6010.c
@@ -1175,6 +1175,7 @@ static int __devinit tusb_probe(struct platform_device *pdev)
 	struct tusb6010_glue		*glue;
 
 	int				ret = -ENOMEM;
+	int				musbid;
 
 	glue = kzalloc(sizeof(*glue), GFP_KERNEL);
 	if (!glue) {
@@ -1182,12 +1183,21 @@ static int __devinit tusb_probe(struct platform_device *pdev)
 		goto err0;
 	}
 
-	musb = platform_device_alloc("musb-hdrc", -1);
+	/* get the musb id */
+	musbid = musb_get_id(&pdev->dev, GFP_KERNEL);
+	if (musbid < 0) {
+		dev_err(&pdev->dev, "failed to allocate musb id\n");
+		ret = -ENOMEM;
+		goto err1;
+	}
+
+	musb = platform_device_alloc("musb-hdrc", musbid);
 	if (!musb) {
 		dev_err(&pdev->dev, "failed to allocate musb device\n");
-		goto err1;
+		goto err2;
 	}
 
+	musb->id			= musbid;
 	musb->dev.parent		= &pdev->dev;
 	musb->dev.dma_mask		= &tusb_dmamask;
 	musb->dev.coherent_dma_mask	= tusb_dmamask;
@@ -1203,26 +1213,29 @@ static int __devinit tusb_probe(struct platform_device *pdev)
 			pdev->num_resources);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to add resources\n");
-		goto err2;
+		goto err3;
 	}
 
 	ret = platform_device_add_data(musb, pdata, sizeof(*pdata));
 	if (ret) {
 		dev_err(&pdev->dev, "failed to add platform_data\n");
-		goto err2;
+		goto err3;
 	}
 
 	ret = platform_device_add(musb);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to register musb device\n");
-		goto err1;
+		goto err3;
 	}
 
 	return 0;
 
-err2:
+err3:
 	platform_device_put(musb);
 
+err2:
+	musb_put_id(&pdev->dev, musbid);
+
 err1:
 	kfree(glue);
 
@@ -1234,6 +1247,7 @@ static int __devexit tusb_remove(struct platform_device *pdev)
 {
 	struct tusb6010_glue		*glue = platform_get_drvdata(pdev);
 
+	musb_put_id(&pdev->dev, glue->musb->id);
 	platform_device_del(glue->musb);
 	platform_device_put(glue->musb);
 	kfree(glue);
diff --git a/drivers/usb/musb/ux500.c b/drivers/usb/musb/ux500.c
index a8c0fad..d62a91f 100644
--- a/drivers/usb/musb/ux500.c
+++ b/drivers/usb/musb/ux500.c
@@ -74,25 +74,34 @@ static int __devinit ux500_probe(struct platform_device *pdev)
 		goto err0;
 	}
 
-	musb = platform_device_alloc("musb-hdrc", -1);
+	/* get the musb id */
+	musbid = musb_get_id(&pdev->dev, GFP_KERNEL);
+	if (musbid < 0) {
+		dev_err(&pdev->dev, "failed to allocate musb id\n");
+		ret = -ENOMEM;
+		goto err1;
+	}
+
+	musb = platform_device_alloc("musb-hdrc", musbid);
 	if (!musb) {
 		dev_err(&pdev->dev, "failed to allocate musb device\n");
-		goto err1;
+		goto err2;
 	}
 
 	clk = clk_get(&pdev->dev, "usb");
 	if (IS_ERR(clk)) {
 		dev_err(&pdev->dev, "failed to get clock\n");
 		ret = PTR_ERR(clk);
-		goto err2;
+		goto err3;
 	}
 
 	ret = clk_enable(clk);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to enable clock\n");
-		goto err3;
+		goto err4;
 	}
 
+	musb->id			= musbid;
 	musb->dev.parent		= &pdev->dev;
 	musb->dev.dma_mask		= pdev->dev.dma_mask;
 	musb->dev.coherent_dma_mask	= pdev->dev.coherent_dma_mask;
@@ -109,32 +118,35 @@ static int __devinit ux500_probe(struct platform_device *pdev)
 			pdev->num_resources);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to add resources\n");
-		goto err4;
+		goto err5;
 	}
 
 	ret = platform_device_add_data(musb, pdata, sizeof(*pdata));
 	if (ret) {
 		dev_err(&pdev->dev, "failed to add platform_data\n");
-		goto err4;
+		goto err5;
 	}
 
 	ret = platform_device_add(musb);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to register musb device\n");
-		goto err4;
+		goto err5;
 	}
 
 	return 0;
 
-err4:
+err5:
 	clk_disable(clk);
 
-err3:
+err4:
 	clk_put(clk);
 
-err2:
+err3:
 	platform_device_put(musb);
 
+err2:
+	musb_put_id(&pdev->dev, musbid);
+
 err1:
 	kfree(glue);
 
@@ -146,6 +158,7 @@ static int __devexit ux500_remove(struct platform_device *pdev)
 {
 	struct ux500_glue	*glue = platform_get_drvdata(pdev);
 
+	musb_put_id(&pdev->dev, glue->musb->id);
 	platform_device_del(glue->musb);
 	platform_device_put(glue->musb);
 	clk_disable(glue->clk);
-- 
1.7.0.4

[PATCH v2 04/11] usb: otg: nop: add support for multiple tranceiver

[Ajay Kumar Gupta]

Currently we have one single nop transceiver support as same is
defined as a global variable in drivers/usb/otg/nop-usb-xceiv.c.
This need to be changed to support multiple otg controller each
using nop transceiver on a platform such as am335x.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
---
 arch/arm/mach-omap2/board-omap3evm.c |    2 +-
 drivers/usb/musb/am35x.c             |    4 ++--
 drivers/usb/musb/blackfin.c          |    4 ++--
 drivers/usb/musb/da8xx.c             |    4 ++--
 drivers/usb/musb/davinci.c           |    6 +++---
 drivers/usb/musb/musb_dsps.c         |   10 +++++-----
 drivers/usb/musb/tusb6010.c          |    6 +++---
 drivers/usb/otg/nop-usb-xceiv.c      |   20 ++++++++++++--------
 include/linux/usb/otg.h              |    9 +++++----
 9 files changed, 35 insertions(+), 30 deletions(-)

diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index ef230a0..a3393bc 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -704,7 +704,7 @@ static void __init omap3_evm_init(void)
 	omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
 
 	/* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
-	usb_nop_xceiv_register();
+	usb_nop_xceiv_register(0);
 
 	if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
 		/* enable EHCI VBUS using GPIO22 */
diff --git a/drivers/usb/musb/am35x.c b/drivers/usb/musb/am35x.c
index 01203eb..eb6220f 100644
--- a/drivers/usb/musb/am35x.c
+++ b/drivers/usb/musb/am35x.c
@@ -364,7 +364,7 @@ static int am35x_musb_init(struct musb *musb)
 	if (!rev)
 		return -ENODEV;
 
-	usb_nop_xceiv_register();
+	usb_nop_xceiv_register(musb->id);
 	musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2);
 	if (IS_ERR_OR_NULL(musb->xceiv))
 		return -ENODEV;
@@ -408,7 +408,7 @@ static int am35x_musb_exit(struct musb *musb)
 		data->set_phy_power(0);
 
 	usb_put_phy(musb->xceiv);
-	usb_nop_xceiv_unregister();
+	usb_nop_xceiv_unregister(musb->xceiv);
 
 	return 0;
 }
diff --git a/drivers/usb/musb/blackfin.c b/drivers/usb/musb/blackfin.c
index c848b82..03d081c 100644
--- a/drivers/usb/musb/blackfin.c
+++ b/drivers/usb/musb/blackfin.c
@@ -415,7 +415,7 @@ static int bfin_musb_init(struct musb *musb)
 	}
 	gpio_direction_output(musb->config->gpio_vrsel, 0);
 
-	usb_nop_xceiv_register();
+	usb_nop_xceiv_register(musb->id);
 	musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2);
 	if (IS_ERR_OR_NULL(musb->xceiv)) {
 		gpio_free(musb->config->gpio_vrsel);
@@ -442,7 +442,7 @@ static int bfin_musb_exit(struct musb *musb)
 	gpio_free(musb->config->gpio_vrsel);
 
 	usb_put_phy(musb->xceiv);
-	usb_nop_xceiv_unregister();
+	usb_nop_xceiv_unregister(musb->xceiv);
 	return 0;
 }
 
diff --git a/drivers/usb/musb/da8xx.c b/drivers/usb/musb/da8xx.c
index cebd9d7..3ce4a92 100644
--- a/drivers/usb/musb/da8xx.c
+++ b/drivers/usb/musb/da8xx.c
@@ -425,7 +425,7 @@ static int da8xx_musb_init(struct musb *musb)
 	if (!rev)
 		goto fail;
 
-	usb_nop_xceiv_register();
+	usb_nop_xceiv_register(musb->id);
 	musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2);
 	if (IS_ERR_OR_NULL(musb->xceiv))
 		goto fail;
@@ -460,7 +460,7 @@ static int da8xx_musb_exit(struct musb *musb)
 	phy_off();
 
 	usb_put_phy(musb->xceiv);
-	usb_nop_xceiv_unregister();
+	usb_nop_xceiv_unregister(musb->xceiv);
 
 	return 0;
 }
diff --git a/drivers/usb/musb/davinci.c b/drivers/usb/musb/davinci.c
index 3f094f2..d5156b3 100644
--- a/drivers/usb/musb/davinci.c
+++ b/drivers/usb/musb/davinci.c
@@ -385,7 +385,7 @@ static int davinci_musb_init(struct musb *musb)
 	void __iomem	*tibase = musb->ctrl_base;
 	u32		revision;
 
-	usb_nop_xceiv_register();
+	usb_nop_xceiv_register(musb->id);
 	musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2);
 	if (IS_ERR_OR_NULL(musb->xceiv))
 		goto unregister;
@@ -447,7 +447,7 @@ static int davinci_musb_init(struct musb *musb)
 fail:
 	usb_put_phy(musb->xceiv);
 unregister:
-	usb_nop_xceiv_unregister();
+	usb_nop_xceiv_unregister(musb->xceiv);
 	return -ENODEV;
 }
 
@@ -496,7 +496,7 @@ static int davinci_musb_exit(struct musb *musb)
 	phy_off();
 
 	usb_put_phy(musb->xceiv);
-	usb_nop_xceiv_unregister();
+	usb_nop_xceiv_unregister(musb->xceiv);
 
 	return 0;
 }
diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c
index a2c8a06..9fcacff 100644
--- a/drivers/usb/musb/musb_dsps.c
+++ b/drivers/usb/musb/musb_dsps.c
@@ -420,8 +420,8 @@ static int dsps_musb_init(struct musb *musb)
 	/* mentor core register starts at offset of 0x400 from musb base */
 	musb->mregs += wrp->musb_core_offset;
 
-	/* NOP driver needs change if supporting dual instance */
-	usb_nop_xceiv_register();
+	/* Register NOP driver */
+	usb_nop_xceiv_register(musb->id);
 	musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2);
 	if (IS_ERR_OR_NULL(musb->xceiv))
 		return -ENODEV;
@@ -456,7 +456,7 @@ static int dsps_musb_init(struct musb *musb)
 	return 0;
 err0:
 	usb_put_phy(musb->xceiv);
-	usb_nop_xceiv_unregister();
+	usb_nop_xceiv_unregister(musb->xceiv);
 	return status;
 }
 
@@ -472,9 +472,9 @@ static int dsps_musb_exit(struct musb *musb)
 	/* Shutdown the on-chip PHY and its PLL. */
 	musb_dsps_phy_control(glue, musb->id, 0);
 
-	/* NOP driver needs change if supporting dual instance */
+	/* Unregister NOP driver */
 	usb_put_phy(musb->xceiv);
-	usb_nop_xceiv_unregister();
+	usb_nop_xceiv_unregister(musb->xceiv);
 
 	return 0;
 }
diff --git a/drivers/usb/musb/tusb6010.c b/drivers/usb/musb/tusb6010.c
index 64a0e95..6b23e55 100644
--- a/drivers/usb/musb/tusb6010.c
+++ b/drivers/usb/musb/tusb6010.c
@@ -1078,7 +1078,7 @@ static int tusb_musb_init(struct musb *musb)
 	void __iomem		*sync = NULL;
 	int			ret;
 
-	usb_nop_xceiv_register();
+	usb_nop_xceiv_register(musb->id);
 	musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2);
 	if (IS_ERR_OR_NULL(musb->xceiv))
 		return -ENODEV;
@@ -1132,7 +1132,7 @@ done:
 			iounmap(sync);
 
 		usb_put_phy(musb->xceiv);
-		usb_nop_xceiv_unregister();
+		usb_nop_xceiv_unregister(musb->xceiv);
 	}
 	return ret;
 }
@@ -1148,7 +1148,7 @@ static int tusb_musb_exit(struct musb *musb)
 	iounmap(musb->sync_va);
 
 	usb_put_phy(musb->xceiv);
-	usb_nop_xceiv_unregister();
+	usb_nop_xceiv_unregister(musb->xceiv);
 	return 0;
 }
 
diff --git a/drivers/usb/otg/nop-usb-xceiv.c b/drivers/usb/otg/nop-usb-xceiv.c
index 803f958..2e5e889 100644
--- a/drivers/usb/otg/nop-usb-xceiv.c
+++ b/drivers/usb/otg/nop-usb-xceiv.c
@@ -35,15 +35,14 @@
 struct nop_usb_xceiv {
 	struct usb_phy		phy;
 	struct device		*dev;
+	struct platform_device	*pd;
 };
 
-static struct platform_device *pd;
-
-void usb_nop_xceiv_register(void)
+void usb_nop_xceiv_register(int id)
 {
-	if (pd)
-		return;
-	pd = platform_device_register_simple("nop_usb_xceiv", -1, NULL, 0);
+	struct platform_device *pd;
+
+	pd = platform_device_register_simple("nop_usb_xceiv", id, NULL, 0);
 	if (!pd) {
 		printk(KERN_ERR "Unable to register usb nop transceiver\n");
 		return;
@@ -51,10 +50,13 @@ void usb_nop_xceiv_register(void)
 }
 EXPORT_SYMBOL(usb_nop_xceiv_register);
 
-void usb_nop_xceiv_unregister(void)
+void usb_nop_xceiv_unregister(struct usb_phy *phy)
 {
+	struct nop_usb_xceiv *nop = container_of(phy,
+			struct nop_usb_xceiv, phy);
+	struct platform_device *pd = nop->pd;
+
 	platform_device_unregister(pd);
-	pd = NULL;
 }
 EXPORT_SYMBOL(usb_nop_xceiv_unregister);
 
@@ -107,11 +109,13 @@ static int __devinit nop_usb_xceiv_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	}
 
+	nop->pd			= pdev;
 	nop->dev		= &pdev->dev;
 	nop->phy.dev		= nop->dev;
 	nop->phy.label		= "nop-xceiv";
 	nop->phy.set_suspend	= nop_set_suspend;
 	nop->phy.state		= OTG_STATE_UNDEFINED;
+	nop->phy.id		= pdev->id;
 
 	nop->phy.otg->phy		= &nop->phy;
 	nop->phy.otg->set_host		= nop_set_host;
diff --git a/include/linux/usb/otg.h b/include/linux/usb/otg.h
index 4636d39..36cc791 100644
--- a/include/linux/usb/otg.h
+++ b/include/linux/usb/otg.h
@@ -95,6 +95,7 @@ struct usb_phy {
 	struct device		*dev;
 	const char		*label;
 	unsigned int		 flags;
+	u8			id;
 
 	enum usb_phy_type	type;
 	enum usb_otg_state	state;
@@ -137,14 +138,14 @@ extern void usb_remove_phy(struct usb_phy *);
 
 #if defined(CONFIG_NOP_USB_XCEIV) || (defined(CONFIG_NOP_USB_XCEIV_MODULE) && defined(MODULE))
 /* sometimes transceivers are accessed only through e.g. ULPI */
-extern void usb_nop_xceiv_register(void);
-extern void usb_nop_xceiv_unregister(void);
+extern void usb_nop_xceiv_register(int id);
+extern void usb_nop_xceiv_unregister(struct usb_phy *);
 #else
-static inline void usb_nop_xceiv_register(void)
+static inline void usb_nop_xceiv_register(int id)
 {
 }
 
-static inline void usb_nop_xceiv_unregister(void)
+static inline void usb_nop_xceiv_unregister(struct usb_phy *phy)
 {
 }
 #endif
-- 
1.7.0.4

[PATCH v2 09/11] usb: musb: dsps: remove explicit NOP device creation

[Ajay Kumar Gupta]

As NOP device node is now added in am33xx tree so remove the call
which creates the NOP platform_device.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
---
 drivers/usb/musb/musb_dsps.c |    3 +--
 1 files changed, 1 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c
index 18a16dd..4c59809 100644
--- a/drivers/usb/musb/musb_dsps.c
+++ b/drivers/usb/musb/musb_dsps.c
@@ -425,8 +425,7 @@ static int dsps_musb_init(struct musb *musb)
 	/* mentor core register starts at offset of 0x400 from musb base */
 	musb->mregs += wrp->musb_core_offset;
 
-	/* Register NOP driver */
-	usb_nop_xceiv_register(musb->id);
+	/* Get the NOP PHY */
 	musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2);
 	if (IS_ERR_OR_NULL(musb->xceiv))
 		return -ENODEV;
-- 
1.7.0.4

[PATCH v2 02/11] usb: musb: kill global and static for multi instance

[Ajay Kumar Gupta]

Moved global variable "musb_debugfs_root" and static variable
"old_state" to 'struct musb' to help support multi instance of
musb controller as present on AM335x platform.

Also removed the global variable "orig_dma_mask" and filled the
dev->dma_mask with parent device's dma_mask.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta-l0cyMroinI0@public.gmane.org>
---
 drivers/usb/musb/musb_core.c    |   16 +++-------------
 drivers/usb/musb/musb_core.h    |    4 ++++
 drivers/usb/musb/musb_debugfs.c |   14 ++++++++------
 3 files changed, 15 insertions(+), 19 deletions(-)

diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c
index 3e09984..a5db4dd 100644
--- a/drivers/usb/musb/musb_core.c
+++ b/drivers/usb/musb/musb_core.c
@@ -1802,10 +1802,9 @@ static const struct attribute_group musb_attr_group = {
 static void musb_irq_work(struct work_struct *data)
 {
 	struct musb *musb = container_of(data, struct musb, irq_work);
-	static int old_state;
 
-	if (musb->xceiv->state != old_state) {
-		old_state = musb->xceiv->state;
+	if (musb->xceiv->state != musb->xceiv_old_state) {
+		musb->xceiv_old_state = musb->xceiv->state;
 		sysfs_notify(&musb->controller->kobj, NULL, "mode");
 	}
 }
@@ -2115,11 +2114,6 @@ fail0:
 /* all implementations (PCI bridge to FPGA, VLYNQ, etc) should just
  * bridge to a platform device; this driver then suffices.
  */
-
-#ifndef CONFIG_MUSB_PIO_ONLY
-static u64	*orig_dma_mask;
-#endif
-
 static int __devinit musb_probe(struct platform_device *pdev)
 {
 	struct device	*dev = &pdev->dev;
@@ -2138,10 +2132,6 @@ static int __devinit musb_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	}
 
-#ifndef CONFIG_MUSB_PIO_ONLY
-	/* clobbered by use_dma=n */
-	orig_dma_mask = dev->dma_mask;
-#endif
 	status = musb_init_controller(dev, irq, base);
 	if (status < 0)
 		iounmap(base);
@@ -2166,7 +2156,7 @@ static int __devexit musb_remove(struct platform_device *pdev)
 	iounmap(ctrl_base);
 	device_init_wakeup(&pdev->dev, 0);
 #ifndef CONFIG_MUSB_PIO_ONLY
-	pdev->dev.dma_mask = orig_dma_mask;
+	pdev->dev.dma_mask = (&dev->dev.parent)->dma_mask;
 #endif
 	return 0;
 }
diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h
index 69ed141..6b6cee9 100644
--- a/drivers/usb/musb/musb_core.h
+++ b/drivers/usb/musb/musb_core.h
@@ -452,6 +452,10 @@ struct musb {
 #endif
 	/* id for multiple musb instances */
 	u8			id;
+	int                     xceiv_old_state;
+#ifdef CONFIG_DEBUG_FS
+	struct dentry           *debugfs_root;
+#endif
 };
 
 static inline struct musb *gadget_to_musb(struct usb_gadget *g)
diff --git a/drivers/usb/musb/musb_debugfs.c b/drivers/usb/musb/musb_debugfs.c
index 40a37c9..b1e8f21 100644
--- a/drivers/usb/musb/musb_debugfs.c
+++ b/drivers/usb/musb/musb_debugfs.c
@@ -103,8 +103,6 @@ static const struct musb_register_map musb_regmap[] = {
 	{  }	/* Terminating Entry */
 };
 
-static struct dentry *musb_debugfs_root;
-
 static int musb_regdump_show(struct seq_file *s, void *unused)
 {
 	struct musb		*musb = s->private;
@@ -240,20 +238,24 @@ int __devinit musb_init_debugfs(struct musb *musb)
 	struct dentry		*root;
 	struct dentry		*file;
 	int			ret;
+	char			name[10];
 
-	root = debugfs_create_dir("musb", NULL);
+	sprintf(name, "musb%d", musb->id);
+	root = debugfs_create_dir(name, NULL);
 	if (!root) {
 		ret = -ENOMEM;
 		goto err0;
 	}
 
-	file = debugfs_create_file("regdump", S_IRUGO, root, musb,
+	sprintf(name, "regdump%d", musb->id);
+	file = debugfs_create_file(name, S_IRUGO, root, musb,
 			&musb_regdump_fops);
 	if (!file) {
 		ret = -ENOMEM;
 		goto err1;
 	}
 
+	sprintf(name, "testmode%d", musb->id);
 	file = debugfs_create_file("testmode", S_IRUGO | S_IWUSR,
 			root, musb, &musb_test_mode_fops);
 	if (!file) {
@@ -261,7 +263,7 @@ int __devinit musb_init_debugfs(struct musb *musb)
 		goto err1;
 	}
 
-	musb_debugfs_root = root;
+	musb->debugfs_root = root;
 
 	return 0;
 
@@ -274,5 +276,5 @@ err0:
 
 void /* __init_or_exit */ musb_exit_debugfs(struct musb *musb)
 {
-	debugfs_remove_recursive(musb_debugfs_root);
+	debugfs_remove_recursive(musb->debugfs_root);
 }
-- 
1.7.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 03/11] usb: musb: am335x: add support for dual instance

[Ajay Kumar Gupta]

AM335x and TI81xx platform has dual musb controller so updating the
musb_dspc.c to support the same.

Changes:
	- Moved otg_workaround timer to glue structure
	- Moved static local variable last_timer to glue structure
	- PHY on/off related cleanups

Signed-off-by: Ajay Kumar Gupta <ajay.gupta-l0cyMroinI0@public.gmane.org>
---
 drivers/usb/musb/musb_dsps.c |   93 +++++++++++++++++++++++++----------------
 1 files changed, 57 insertions(+), 36 deletions(-)

diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c
index 2174699..a2c8a06 100644
--- a/drivers/usb/musb/musb_dsps.c
+++ b/drivers/usb/musb/musb_dsps.c
@@ -105,6 +105,8 @@ struct dsps_musb_wrapper {
 	/* miscellaneous stuff */
 	u32		musb_core_offset;
 	u8		poll_seconds;
+	/* number of musb instances */
+	u8		instances;
 };
 
 /**
@@ -112,16 +114,18 @@ struct dsps_musb_wrapper {
  */
 struct dsps_glue {
 	struct device *dev;
-	struct platform_device *musb;	/* child musb pdev */
+	struct platform_device *musb[2];	/* child musb pdev */
 	const struct dsps_musb_wrapper *wrp; /* wrapper register offsets */
-	struct timer_list timer;	/* otg_workaround timer */
-	u32 __iomem *usb_ctrl;
+	struct timer_list timer[2];	/* otg_workaround timer */
+	unsigned long last_timer[2];    /* last timer data for each instance */
+	u32 __iomem *usb_ctrl[2];
 	u8      usbss_rev;
 };
 
 /**
  * musb_dsps_phy_control - phy on/off
  * @glue: struct dsps_glue *
+ * @id: musb instance
  * @on: flag for phy to be switched on or off
  *
  * This is to enable the PHY using usb_ctrl register in system control
@@ -130,11 +134,11 @@ struct dsps_glue {
  * XXX: This function will be removed once we have a seperate driver for
  * control module
  */
-static void musb_dsps_phy_control(struct dsps_glue *glue, u8 on)
+static void musb_dsps_phy_control(struct dsps_glue *glue, u8 id, u8 on)
 {
 	u32 usbphycfg;
 
-	usbphycfg = __raw_readl(glue->usb_ctrl);
+	usbphycfg = __raw_readl(glue->usb_ctrl[id]);
 
 	if (on) {
 		if (glue->usbss_rev == MUSB_USBSS_REV_816X) {
@@ -157,7 +161,7 @@ static void musb_dsps_phy_control(struct dsps_glue *glue, u8 on)
 				glue->usbss_rev == MUSB_USBSS_REV_33XX)
 			usbphycfg |= USBPHY_CM_PWRDN | USBPHY_OTG_PWRDN;
 	}
-	__raw_writel(usbphycfg, glue->usb_ctrl);
+	__raw_writel(usbphycfg, glue->usb_ctrl[id]);
 }
 /**
  * dsps_musb_enable - enable interrupts
@@ -247,7 +251,7 @@ static void otg_timer(unsigned long _musb)
 
 		devctl = dsps_readb(mregs, MUSB_DEVCTL);
 		if (devctl & MUSB_DEVCTL_BDEVICE)
-			mod_timer(&glue->timer,
+			mod_timer(&glue->timer[musb->id],
 					jiffies + wrp->poll_seconds * HZ);
 		else
 			musb->xceiv->state = OTG_STATE_A_IDLE;
@@ -263,7 +267,6 @@ static void dsps_musb_try_idle(struct musb *musb, unsigned long timeout)
 	struct device *dev = musb->controller;
 	struct platform_device *pdev = to_platform_device(dev->parent);
 	struct dsps_glue *glue = platform_get_drvdata(pdev);
-	static unsigned long last_timer;
 
 	if (!is_otg_enabled(musb))
 		return;
@@ -276,22 +279,23 @@ static void dsps_musb_try_idle(struct musb *musb, unsigned long timeout)
 				musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) {
 		dev_dbg(musb->controller, "%s active, deleting timer\n",
 				otg_state_string(musb->xceiv->state));
-		del_timer(&glue->timer);
-		last_timer = jiffies;
+		del_timer(&glue->timer[musb->id]);
+		glue->last_timer[musb->id] = jiffies;
 		return;
 	}
 
-	if (time_after(last_timer, timeout) && timer_pending(&glue->timer)) {
+	if (time_after(glue->last_timer[musb->id], timeout) &&
+				timer_pending(&glue->timer[musb->id])) {
 		dev_dbg(musb->controller,
 			"Longer idle timer already pending, ignoring...\n");
 		return;
 	}
-	last_timer = timeout;
+	glue->last_timer[musb->id] = timeout;
 
 	dev_dbg(musb->controller, "%s inactive, starting idle timer for %u ms\n",
 		otg_state_string(musb->xceiv->state),
 			jiffies_to_msecs(timeout - jiffies));
-	mod_timer(&glue->timer, timeout);
+	mod_timer(&glue->timer[musb->id], timeout);
 }
 
 static irqreturn_t dsps_interrupt(int irq, void *hci)
@@ -360,7 +364,7 @@ static irqreturn_t dsps_interrupt(int irq, void *hci)
 			 */
 			musb->int_usb &= ~MUSB_INTR_VBUSERROR;
 			musb->xceiv->state = OTG_STATE_A_WAIT_VFALL;
-			mod_timer(&glue->timer,
+			mod_timer(&glue->timer[musb->id],
 					jiffies + wrp->poll_seconds * HZ);
 			WARNING("VBUS error workaround (delay coming)\n");
 		} else if (is_host_enabled(musb) && drvvbus) {
@@ -368,7 +372,7 @@ static irqreturn_t dsps_interrupt(int irq, void *hci)
 			MUSB_HST_MODE(musb);
 			musb->xceiv->otg->default_a = 1;
 			musb->xceiv->state = OTG_STATE_A_WAIT_VRISE;
-			del_timer(&glue->timer);
+			del_timer(&glue->timer[musb->id]);
 		} else {
 			musb->is_active = 0;
 			MUSB_DEV_MODE(musb);
@@ -395,7 +399,8 @@ static irqreturn_t dsps_interrupt(int irq, void *hci)
 
 	/* Poll for ID change */
 	if (is_otg_enabled(musb) && musb->xceiv->state == OTG_STATE_B_IDLE)
-		mod_timer(&glue->timer, jiffies + wrp->poll_seconds * HZ);
+		mod_timer(&glue->timer[musb->id],
+				jiffies + wrp->poll_seconds * HZ);
 
 	spin_unlock_irqrestore(&musb->lock, flags);
 
@@ -429,13 +434,14 @@ static int dsps_musb_init(struct musb *musb)
 	}
 
 	if (is_host_enabled(musb))
-		setup_timer(&glue->timer, otg_timer, (unsigned long) musb);
+		setup_timer(&glue->timer[musb->id], otg_timer,
+			(unsigned long) musb);
 
 	/* Reset the musb */
 	dsps_writel(reg_base, wrp->control, (1 << wrp->reset));
 
 	/* Start the on-chip PHY and its PLL. */
-	musb_dsps_phy_control(glue, 1);
+	musb_dsps_phy_control(glue, musb->id, 1);
 
 	musb->isr = dsps_interrupt;
 
@@ -461,10 +467,10 @@ static int dsps_musb_exit(struct musb *musb)
 	struct dsps_glue *glue = platform_get_drvdata(pdev);
 
 	if (is_host_enabled(musb))
-		del_timer_sync(&glue->timer);
+		del_timer_sync(&glue->timer[musb->id]);
 
 	/* Shutdown the on-chip PHY and its PLL. */
-	musb_dsps_phy_control(glue, 0);
+	musb_dsps_phy_control(glue, musb->id, 0);
 
 	/* NOP driver needs change if supporting dual instance */
 	usb_put_phy(musb->xceiv);
@@ -504,8 +510,8 @@ static int __devinit dsps_create_musb_pdev(struct dsps_glue *glue, u8 id)
 		goto err0;
 	}
 
-	glue->usb_ctrl = devm_request_and_ioremap(&pdev->dev, res);
-	if (glue->usb_ctrl == NULL) {
+	glue->usb_ctrl[id] = devm_request_and_ioremap(&pdev->dev, res);
+	if (glue->usb_ctrl[id] == NULL) {
 		dev_err(dev, "Failed to obtain usb_ctrl%d memory\n", id);
 		ret = -ENODEV;
 		goto err0;
@@ -554,7 +560,7 @@ static int __devinit dsps_create_musb_pdev(struct dsps_glue *glue, u8 id)
 	musb->dev.dma_mask		= &musb_dmamask;
 	musb->dev.coherent_dma_mask	= musb_dmamask;
 
-	glue->musb			= musb;
+	glue->musb[id]			= musb;
 
 	pdata->platform_ops		= &dsps_ops;
 
@@ -586,11 +592,11 @@ err0:
 	return ret;
 }
 
-static void __devexit dsps_delete_musb_pdev(struct dsps_glue *glue)
+static void __devexit dsps_delete_musb_pdev(struct dsps_glue *glue, u8 id)
 {
-	musb_put_id(glue->dev, glue->musb->id);
-	platform_device_del(glue->musb);
-	platform_device_put(glue->musb);
+	musb_put_id(glue->dev, glue->musb[id]->id);
+	platform_device_del(glue->musb[id]);
+	platform_device_put(glue->musb[id]);
 }
 
 static int __devinit dsps_probe(struct platform_device *pdev)
@@ -601,7 +607,7 @@ static int __devinit dsps_probe(struct platform_device *pdev)
 	struct dsps_glue *glue;
 	struct resource *iomem;
 	u32 __iomem *usbss;
-	int ret;
+	int ret, i;
 
 	/* allocate glue */
 	glue = kzalloc(sizeof(*glue), GFP_KERNEL);
@@ -645,11 +651,16 @@ static int __devinit dsps_probe(struct platform_device *pdev)
 		goto err2;
 	}
 
-	/* create the child platform device for first instances of musb */
-	ret = dsps_create_musb_pdev(glue, 0);
-	if (ret != 0) {
-		dev_err(&pdev->dev, "failed to create child pdev\n");
-		goto err3;
+	/* create the child platform device for all instances of musb */
+	for (i = 0; i < wrp->instances ; i++) {
+		ret = dsps_create_musb_pdev(glue, i);
+		if (ret != 0) {
+			dev_err(&pdev->dev, "failed to create child pdev\n");
+			/* release resources of previously created instances */
+			for (i--; i >= 0 ; i--)
+				dsps_delete_musb_pdev(glue, i);
+			goto err3;
+		}
 	}
 
 	/* read the usbss revision register */
@@ -670,9 +681,12 @@ err0:
 static int __devexit dsps_remove(struct platform_device *pdev)
 {
 	struct dsps_glue *glue = platform_get_drvdata(pdev);
+	const struct dsps_musb_wrapper *wrp = glue->wrp;
+	int i;
 
 	/* delete the child platform device */
-	dsps_delete_musb_pdev(glue);
+	for (i = 0; i < wrp->instances ; i++)
+		dsps_delete_musb_pdev(glue, i);
 
 	/* disable usbss clocks */
 	pm_runtime_put(&pdev->dev);
@@ -687,9 +701,12 @@ static int dsps_suspend(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev->parent);
 	struct dsps_glue *glue = platform_get_drvdata(pdev);
+	const struct dsps_musb_wrapper *wrp = glue->wrp;
+	int i;
 
 	/* Shutdown the on-chip PHY and its PLL. */
-	musb_dsps_phy_control(glue, 0);
+	for (i = 0 ; i < wrp->instances ; i++)
+		musb_dsps_phy_control(glue, i, 0);
 
 	return 0;
 }
@@ -698,9 +715,12 @@ static int dsps_resume(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev->parent);
 	struct dsps_glue *glue = platform_get_drvdata(pdev);
+	const struct dsps_musb_wrapper *wrp = glue->wrp;
+	int i;
 
 	/* Start the on-chip PHY and its PLL. */
-	musb_dsps_phy_control(glue, 1);
+	for (i = 0 ; i < wrp->instances ; i++)
+		musb_dsps_phy_control(glue, i, 1);
 
 	return 0;
 }
@@ -736,6 +756,7 @@ static const struct dsps_musb_wrapper ti81xx_driver_data __devinitconst = {
 	.rxep_bitmap		= (0xfffe << 16),
 	.musb_core_offset	= 0x400,
 	.poll_seconds		= 2,
+	.instances		= 2,
 };
 
 static const struct platform_device_id musb_dsps_id_table[] __devinitconst = {
-- 
1.7.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 05/11] usb: musb: dsps: add dt support

[Ajay Kumar Gupta]

Added device tree support for dsps musb glue driver and updated the
Documentation with device tree binding information.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta-l0cyMroinI0@public.gmane.org>
---
 .../devicetree/bindings/usb/am33xx-usb.txt         |   14 +++++
 drivers/usb/musb/musb_dsps.c                       |   62 +++++++++++++++++---
 2 files changed, 67 insertions(+), 9 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/usb/am33xx-usb.txt

diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
new file mode 100644
index 0000000..ca8fa56
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
@@ -0,0 +1,14 @@
+AM33XX MUSB GLUE
+ - compatible : Should be "ti,musb-am33xx"
+ - ti,hwmods : must be "usb_otg_hs"
+ - multipoint : Should be "1" indicating the musb controller supports
+   multipoint. This is a MUSB configuration-specific setting.
+ - num_eps : Specifies the number of endpoints. This is also a
+   MUSB configuration-specific setting. Should be set to "16"
+ - ram_bits : Specifies the ram address size. Should be set to "12"
+ - port0_mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
+   represents PERIPHERAL.
+ - port1_mode : Should be "1" to represent HOST. "3" signifies OTG and "2"
+   represents PERIPHERAL.
+ - power : Should be "250". This signifies the controller can supply upto
+   500mA when operating in host mode.
diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c
index 9fcacff..18a16dd 100644
--- a/drivers/usb/musb/musb_dsps.c
+++ b/drivers/usb/musb/musb_dsps.c
@@ -31,6 +31,7 @@
 
 #include <linux/init.h>
 #include <linux/io.h>
+#include <linux/of.h>
 #include <linux/err.h>
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
@@ -45,6 +46,10 @@
 
 #include "musb_core.h"
 
+#ifdef CONFIG_OF
+static const struct of_device_id musb_dsps_of_match[];
+#endif
+
 /**
  * avoid using musb_readx()/musb_writex() as glue layer should not be
  * dependent on musb core layer symbols.
@@ -496,6 +501,8 @@ static int __devinit dsps_create_musb_pdev(struct dsps_glue *glue, u8 id)
 	struct device *dev = glue->dev;
 	struct platform_device *pdev = to_platform_device(dev);
 	struct musb_hdrc_platform_data  *pdata = dev->platform_data;
+	struct device_node *np = pdev->dev.of_node;
+	struct musb_hdrc_config	*config;
 	struct platform_device	*musb;
 	struct resource *res;
 	struct resource	resources[2];
@@ -562,14 +569,40 @@ static int __devinit dsps_create_musb_pdev(struct dsps_glue *glue, u8 id)
 
 	glue->musb[id]			= musb;
 
-	pdata->platform_ops		= &dsps_ops;
-
 	ret = platform_device_add_resources(musb, resources, 2);
 	if (ret) {
 		dev_err(dev, "failed to add resources\n");
 		goto err2;
 	}
 
+	if (np) {
+		pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+		if (!pdata) {
+			dev_err(&pdev->dev,
+				"failed to allocate musb platfrom data\n");
+			ret = -ENOMEM;
+			goto err2;
+		}
+
+		config = devm_kzalloc(&pdev->dev, sizeof(*config), GFP_KERNEL);
+		if (!config) {
+			dev_err(&pdev->dev,
+				"failed to allocate musb hdrc config\n");
+			goto err2;
+		}
+
+		of_property_read_u32(np, "num_eps", (u32 *)&config->num_eps);
+		of_property_read_u32(np, "ram_bits", (u32 *)&config->ram_bits);
+		sprintf(res_name, "port%d_mode", id);
+		of_property_read_u32(np, res_name, (u32 *)&pdata->mode);
+		of_property_read_u32(np, "power", (u32 *)&pdata->power);
+		config->multipoint = of_property_read_bool(np, "multipoint");
+
+		pdata->config		= config;
+	}
+
+	pdata->platform_ops		= &dsps_ops;
+
 	ret = platform_device_add_data(musb, pdata, sizeof(*pdata));
 	if (ret) {
 		dev_err(dev, "failed to add platform_data\n");
@@ -601,14 +634,22 @@ static void __devexit dsps_delete_musb_pdev(struct dsps_glue *glue, u8 id)
 
 static int __devinit dsps_probe(struct platform_device *pdev)
 {
-	const struct platform_device_id *id = platform_get_device_id(pdev);
-	const struct dsps_musb_wrapper *wrp =
-				(struct dsps_musb_wrapper *)id->driver_data;
+	struct device_node *np = pdev->dev.of_node;
+	const struct of_device_id *match;
+	const struct dsps_musb_wrapper *wrp;
 	struct dsps_glue *glue;
 	struct resource *iomem;
 	u32 __iomem *usbss;
 	int ret, i;
 
+	match = of_match_node(musb_dsps_of_match, np);
+	if (!match) {
+		dev_err(&pdev->dev, "fail to get matching of_match struct\n");
+		ret = -EINVAL;
+		goto err0;
+	}
+	wrp = match->data;
+
 	/* allocate glue */
 	glue = kzalloc(sizeof(*glue), GFP_KERNEL);
 	if (!glue) {
@@ -768,13 +809,16 @@ static const struct platform_device_id musb_dsps_id_table[] __devinitconst = {
 };
 MODULE_DEVICE_TABLE(platform, musb_dsps_id_table);
 
+#ifdef CONFIG_OF
 static const struct of_device_id musb_dsps_of_match[] __devinitconst = {
-	{ .compatible = "musb-ti81xx", },
-	{ .compatible = "ti,ti81xx-musb", },
-	{ .compatible = "ti,am335x-musb", },
+	{ .compatible = "ti,musb-am33xx",
+		.data = (void *) &ti81xx_driver_data, },
 	{  },
 };
 MODULE_DEVICE_TABLE(of, musb_dsps_of_match);
+#else
+#define musb_dsps_of_match NULL
+#endif
 
 static struct platform_driver dsps_usbss_driver = {
 	.probe		= dsps_probe,
@@ -782,7 +826,7 @@ static struct platform_driver dsps_usbss_driver = {
 	.driver         = {
 		.name   = "musb-dsps",
 		.pm	= &dsps_pm_ops,
-		.of_match_table	= musb_dsps_of_match,
+		.of_match_table	= of_match_ptr(musb_dsps_of_match),
 	},
 	.id_table	= musb_dsps_id_table,
 };
-- 
1.7.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 06/11] arm/dts: am33xx: Add dt data for usbss

[Ajay Kumar Gupta]

Added device tree data for usbss on am33xx. There are two musb controllers
on am33xx platform so have port0_mode and port1_mode additional data.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta-l0cyMroinI0@public.gmane.org>
---
 arch/arm/boot/dts/am33xx.dtsi |   11 +++++++++++
 1 files changed, 11 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 59509c4..b572803 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -154,5 +154,16 @@
 			#size-cells = <0>;
 			ti,hwmods = "i2c3";
 		};
+
+		usb_otg_hs: usb_otg_hs@47400000 {
+			compatible = "ti,musb-am33xx";
+			ti,hwmods = "usb_otg_hs";
+			multipoint = <1>;
+			num_eps = <16>;
+			ram_bits = <12>;
+			port0_mode = <3>;
+			port1_mode = <1>;
+			power = <250>;
+		};
 	};
 };
-- 
1.7.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v2 06/11] arm/dts: am33xx: Add dt data for usbss

[Sergei Shtylyov]

Hello.

On 17-07-2012 13:13, Ajay Kumar Gupta wrote:

> Added device tree data for usbss on am33xx. There are two musb controllers
> on am33xx platform so have port0_mode and port1_mode additional data.

> Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
> ---
>   arch/arm/boot/dts/am33xx.dtsi |   11 +++++++++++
>   1 files changed, 11 insertions(+), 0 deletions(-)

> diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
> index 59509c4..b572803 100644
> --- a/arch/arm/boot/dts/am33xx.dtsi
> +++ b/arch/arm/boot/dts/am33xx.dtsi
> @@ -154,5 +154,16 @@
>   			#size-cells = <0>;
>   			ti,hwmods = "i2c3";
>   		};
> +
> +		usb_otg_hs: usb_otg_hs@47400000 {

    The "reg" property is absent, so why did you give the node name the 
address postfix?

> +			compatible = "ti,musb-am33xx";
> +			ti,hwmods = "usb_otg_hs";
> +			multipoint = <1>;
> +			num_eps = <16>;
> +			ram_bits = <12>;
> +			port0_mode = <3>;
> +			port1_mode = <1>;
> +			power = <250>;
> +		};

WBR, Sergei

RE: [PATCH v2 06/11] arm/dts: am33xx: Add dt data for usbss

[Gupta, Ajay Kumar]

Hi,
> On 17-07-2012 13:13, Ajay Kumar Gupta wrote:
> 
> > Added device tree data for usbss on am33xx. There are two musb
> controllers
> > on am33xx platform so have port0_mode and port1_mode additional data.
> 
> > Signed-off-by: Ajay Kumar Gupta <ajay.gupta-l0cyMroinI0@public.gmane.org>
> > ---
> >   arch/arm/boot/dts/am33xx.dtsi |   11 +++++++++++
> >   1 files changed, 11 insertions(+), 0 deletions(-)
> 
> > diff --git a/arch/arm/boot/dts/am33xx.dtsi
> b/arch/arm/boot/dts/am33xx.dtsi
> > index 59509c4..b572803 100644
> > --- a/arch/arm/boot/dts/am33xx.dtsi
> > +++ b/arch/arm/boot/dts/am33xx.dtsi
> > @@ -154,5 +154,16 @@
> >   			#size-cells = <0>;
> >   			ti,hwmods = "i2c3";
> >   		};
> > +
> > +		usb_otg_hs: usb_otg_hs@47400000 {
> 
>     The "reg" property is absent, so why did you give the node name the
> address postfix?

Currently "reg" property is coming from "ti hwmods".

Thanks,
Ajay
> 
> > +			compatible = "ti,musb-am33xx";
> > +			ti,hwmods = "usb_otg_hs";
> > +			multipoint = <1>;
> > +			num_eps = <16>;
> > +			ram_bits = <12>;
> > +			port0_mode = <3>;
> > +			port1_mode = <1>;
> > +			power = <250>;
> > +		};
> 
> WBR, Sergei

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

RE: [PATCH v2 06/11] arm/dts: am33xx: Add dt data for usbss

[Gupta, Ajay Kumar]

Hi
> > On 17-07-2012 13:13, Ajay Kumar Gupta wrote:
> >
> > > Added device tree data for usbss on am33xx. There are two musb
> > controllers
> > > on am33xx platform so have port0_mode and port1_mode additional
> data.
> >
> > > Signed-off-by: Ajay Kumar Gupta <ajay.gupta-l0cyMroinI0@public.gmane.org>
> > > ---
> > >   arch/arm/boot/dts/am33xx.dtsi |   11 +++++++++++
> > >   1 files changed, 11 insertions(+), 0 deletions(-)
> >
> > > diff --git a/arch/arm/boot/dts/am33xx.dtsi
> > b/arch/arm/boot/dts/am33xx.dtsi
> > > index 59509c4..b572803 100644
> > > --- a/arch/arm/boot/dts/am33xx.dtsi
> > > +++ b/arch/arm/boot/dts/am33xx.dtsi
> > > @@ -154,5 +154,16 @@
> > >   			#size-cells = <0>;
> > >   			ti,hwmods = "i2c3";
> > >   		};
> > > +
> > > +		usb_otg_hs: usb_otg_hs@47400000 {
> >
> >     The "reg" property is absent, so why did you give the node name
> the
> > address postfix?
> 
> Currently "reg" property is coming from "ti hwmods".

I meant base addresses are coming from hwmods and so there is no "reg"
property added here. I will update the patch dropping address postfix.

Ajay

> > > +			compatible = "ti,musb-am33xx";
> > > +			ti,hwmods = "usb_otg_hs";
> > > +			multipoint = <1>;
> > > +			num_eps = <16>;
> > > +			ram_bits = <12>;
> > > +			port0_mode = <3>;
> > > +			port1_mode = <1>;
> > > +			power = <250>;
> > > +		};
> >
> > WBR, Sergei
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap"
> in
> the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 07/11] usb: otg: nop: add dt support

[Ajay Kumar Gupta]

Added device tree support for nop transceiver driver and updated the
Documentation with device tree binding information for am33xx platform.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta-l0cyMroinI0@public.gmane.org>
---
 .../devicetree/bindings/usb/am33xx-usb.txt         |    3 +++
 drivers/usb/otg/nop-usb-xceiv.c                    |   12 ++++++++++++
 2 files changed, 15 insertions(+), 0 deletions(-)

diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
index ca8fa56..a314720 100644
--- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt
+++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
@@ -12,3 +12,6 @@ AM33XX MUSB GLUE
    represents PERIPHERAL.
  - power : Should be "250". This signifies the controller can supply upto
    500mA when operating in host mode.
+
+NOP USB PHY
+ - compatible : Should be "ti,nop-xceiv-usb"
diff --git a/drivers/usb/otg/nop-usb-xceiv.c b/drivers/usb/otg/nop-usb-xceiv.c
index 2e5e889..0bca4d1 100644
--- a/drivers/usb/otg/nop-usb-xceiv.c
+++ b/drivers/usb/otg/nop-usb-xceiv.c
@@ -27,6 +27,7 @@
  */
 
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
 #include <linux/usb/otg.h>
@@ -152,12 +153,23 @@ static int __devexit nop_usb_xceiv_remove(struct platform_device *pdev)
 	return 0;
 }
 
+#ifdef CONFIG_OF
+static const struct of_device_id nop_xceiv_id_table[] = {
+	{ .compatible = "ti,nop-xceiv-usb" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, nop_xceiv_id_table);
+#else
+#define nop_xceiv_id_table NULL
+#endif
+
 static struct platform_driver nop_usb_xceiv_driver = {
 	.probe		= nop_usb_xceiv_probe,
 	.remove		= __devexit_p(nop_usb_xceiv_remove),
 	.driver		= {
 		.name	= "nop_usb_xceiv",
 		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(nop_xceiv_id_table),
 	},
 };
 
-- 
1.7.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v2 07/11] usb: otg: nop: add dt support

[Sergei Shtylyov]

Hello.

On 17-07-2012 13:13, Ajay Kumar Gupta wrote:

> Added device tree support for nop transceiver driver and updated the
> Documentation with device tree binding information for am33xx platform.

> Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
> ---
>   .../devicetree/bindings/usb/am33xx-usb.txt         |    3 +++
>   drivers/usb/otg/nop-usb-xceiv.c                    |   12 ++++++++++++
>   2 files changed, 15 insertions(+), 0 deletions(-)

> diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
> index ca8fa56..a314720 100644
> --- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt
> +++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
> @@ -12,3 +12,6 @@ AM33XX MUSB GLUE
>      represents PERIPHERAL.
>    - power : Should be "250". This signifies the controller can supply upto
>      500mA when operating in host mode.
> +
> +NOP USB PHY
> + - compatible : Should be "ti,nop-xceiv-usb"

    Why are you declaring it as TI specific. There's nothing company specific 
in the NOP transceiver.

WBR, Sergei

RE: [PATCH v2 07/11] usb: otg: nop: add dt support

[Gupta, Ajay Kumar]

Hi,
> 
> On 17-07-2012 13:13, Ajay Kumar Gupta wrote:
> 
> > Added device tree support for nop transceiver driver and updated the
> > Documentation with device tree binding information for am33xx
> platform.
> 
> > Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
> > ---
> >   .../devicetree/bindings/usb/am33xx-usb.txt         |    3 +++
> >   drivers/usb/otg/nop-usb-xceiv.c                    |   12
> ++++++++++++
> >   2 files changed, 15 insertions(+), 0 deletions(-)
> 
> > diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt
> b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
> > index ca8fa56..a314720 100644
> > --- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt
> > +++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
> > @@ -12,3 +12,6 @@ AM33XX MUSB GLUE
> >      represents PERIPHERAL.
> >    - power : Should be "250". This signifies the controller can
> supply upto
> >      500mA when operating in host mode.
> > +
> > +NOP USB PHY
> > + - compatible : Should be "ti,nop-xceiv-usb"
> 
>     Why are you declaring it as TI specific. There's nothing company
> specific in the NOP transceiver.

Thanks for review. I will change this to "nop-xceiv-usb".

Ajay
> 
> WBR, Sergei

[PATCH v2 08/11] arm/dts: am33xx: add dt data for usb nop phy

[Ajay Kumar Gupta]

AM33xx has two musb controller and they have one NOP PHY each.
Added the device tree data for NOP PHY.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta-l0cyMroinI0@public.gmane.org>
---
 arch/arm/boot/dts/am33xx.dtsi |    8 ++++++++
 1 files changed, 8 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index b572803..3bd9911 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -155,6 +155,14 @@
 			ti,hwmods = "i2c3";
 		};
 
+		usb0_phy: phy@1 {
+			compatible = "ti,nop-xceiv-usb";
+		};
+
+		usb1_phy: phy@2 {
+			compatible = "ti,nop-xceiv-usb";
+		};
+
 		usb_otg_hs: usb_otg_hs@47400000 {
 			compatible = "ti,musb-am33xx";
 			ti,hwmods = "usb_otg_hs";
-- 
1.7.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v2 08/11] arm/dts: am33xx: add dt data for usb nop phy

[Sergei Shtylyov]

Hello.

On 17-07-2012 13:13, Ajay Kumar Gupta wrote:

> AM33xx has two musb controller and they have one NOP PHY each.
> Added the device tree data for NOP PHY.

> Signed-off-by: Ajay Kumar Gupta <ajay.gupta-l0cyMroinI0@public.gmane.org>
> ---
>   arch/arm/boot/dts/am33xx.dtsi |    8 ++++++++
>   1 files changed, 8 insertions(+), 0 deletions(-)

> diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
> index b572803..3bd9911 100644
> --- a/arch/arm/boot/dts/am33xx.dtsi
> +++ b/arch/arm/boot/dts/am33xx.dtsi
> @@ -155,6 +155,14 @@
>   			ti,hwmods = "i2c3";
>   		};
>
> +		usb0_phy: phy@1 {
> +			compatible = "ti,nop-xceiv-usb";
> +		};
> +
> +		usb1_phy: phy@2 {
> +			compatible = "ti,nop-xceiv-usb";
> +		};

    No "reg" property again, and address postfix in the node name?

WBR, Sergei


--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

RE: [PATCH v2 08/11] arm/dts: am33xx: add dt data for usb nop phy

[Gupta, Ajay Kumar]

Hi,

> > AM33xx has two musb controller and they have one NOP PHY each.
> > Added the device tree data for NOP PHY.
> 
> > Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
> > ---
> >   arch/arm/boot/dts/am33xx.dtsi |    8 ++++++++
> >   1 files changed, 8 insertions(+), 0 deletions(-)
> 
> > diff --git a/arch/arm/boot/dts/am33xx.dtsi
> b/arch/arm/boot/dts/am33xx.dtsi
> > index b572803..3bd9911 100644
> > --- a/arch/arm/boot/dts/am33xx.dtsi
> > +++ b/arch/arm/boot/dts/am33xx.dtsi
> > @@ -155,6 +155,14 @@
> >   			ti,hwmods = "i2c3";
> >   		};
> >
> > +		usb0_phy: phy@1 {
> > +			compatible = "ti,nop-xceiv-usb";
> > +		};
> > +
> > +		usb1_phy: phy@2 {
> > +			compatible = "ti,nop-xceiv-usb";
> > +		};
> 
>     No "reg" property again, and address postfix in the node name?

I will update this to 
+		usb0_phy: phy0 {
+		usb1_phy: phy1 {

Thanks,
Ajay
> 
> WBR, Sergei
> 

[PATCH v2 10/11] usb: musb: dsps: get the PHY using phandle api

[Ajay Kumar Gupta]

AM33xx has two PHY of same type used by each musb controller so
use phandle of phy nodes to get the phy pointer.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta-l0cyMroinI0@public.gmane.org>
---
 .../devicetree/bindings/usb/am33xx-usb.txt         |    2 ++
 drivers/usb/musb/musb_dsps.c                       |    4 +++-
 2 files changed, 5 insertions(+), 1 deletions(-)

diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
index a314720..4ed0091 100644
--- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt
+++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
@@ -12,6 +12,8 @@ AM33XX MUSB GLUE
    represents PERIPHERAL.
  - power : Should be "250". This signifies the controller can supply upto
    500mA when operating in host mode.
+ - usb0-phy : phandle for usb0 NOP PHY
+ - usb1-phy : phandle for usb1 NOP PHY
 
 NOP USB PHY
  - compatible : Should be "ti,nop-xceiv-usb"
diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c
index 4c59809..e2b0729 100644
--- a/drivers/usb/musb/musb_dsps.c
+++ b/drivers/usb/musb/musb_dsps.c
@@ -419,6 +419,7 @@ static int dsps_musb_init(struct musb *musb)
 	struct dsps_glue *glue = platform_get_drvdata(pdev);
 	const struct dsps_musb_wrapper *wrp = glue->wrp;
 	void __iomem *reg_base = musb->ctrl_base;
+	char name[10];
 	u32 rev, val;
 	int status;
 
@@ -426,7 +427,8 @@ static int dsps_musb_init(struct musb *musb)
 	musb->mregs += wrp->musb_core_offset;
 
 	/* Get the NOP PHY */
-	musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2);
+	sprintf(name, "usb%d-phy", musb->id);
+	musb->xceiv = devm_usb_get_phy_by_phandle(&pdev->dev, name);
 	if (IS_ERR_OR_NULL(musb->xceiv))
 		return -ENODEV;
 
-- 
1.7.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 11/11] arm/dts: am33xx: add phy phandle to usbss

[Ajay Kumar Gupta]

Added NOP PHY phandle to usbss device node as same will be used
to get the phy from otg framework.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta-l0cyMroinI0@public.gmane.org>
---
 arch/arm/boot/dts/am33xx.dtsi |    2 ++
 1 files changed, 2 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 3bd9911..0e7aaaa 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -172,6 +172,8 @@
 			port0_mode = <3>;
 			port1_mode = <1>;
 			power = <250>;
+			usb0-phy = <&usb0_phy>;
+			usb1-phy = <&usb1_phy>;
 		};
 	};
 };
-- 
1.7.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html