* [PATCH] libata: blacklist NCQ on OCZ CORE 2 SSD
@ 2008-12-15 21:17 Lubomír Bulej
2008-12-16 0:36 ` Robert Hancock
2008-12-22 8:14 ` Tejun Heo
0 siblings, 2 replies; 4+ messages in thread
From: Lubomír Bulej @ 2008-12-15 21:17 UTC (permalink / raw)
To: jgarzik; +Cc: linux-ide
[-- Attachment #1: Type: text/plain, Size: 1098 bytes --]
Hello,
after putting a 250G OCZ CORE v2 SSD into my notebook, I have to endure
several invocations of the ata EH before the kernel decides to disable NCQ due
too many errors. The drive reports NCQ of depth 1, which is probably useless
anyway.
The patchlet below saves me the waiting for the completion of several ata EH
invocations, but I'm not sure if this is the right solution. Attached are two
dmesg dumps, one with errors and the other with the patchlet compiled in.
Attached is also "hdparm -I" of the drive.
Best regards,
Lubomir
--- linux-2.6.27.7-134.fc10/drivers/ata/libata-core.c.orig 2008-12-15
17:43:28.000000000 +0100
+++ linux-2.6.27.7-134.fc10/drivers/ata/libata-core.c 2008-12-15
21:14:58.488534786 +0100
@@ -3970,6 +3970,7 @@
{ "Maxtor 7V300F0", "VA111630", ATA_HORKAGE_NONCQ },
{ "ST380817AS", "3.42", ATA_HORKAGE_NONCQ },
{ "ST3160023AS", "3.42", ATA_HORKAGE_NONCQ },
+ { "OCZ CORE_SSD", "02.10104", ATA_HORKAGE_NONCQ },
/* Blacklist entries taken from Silicon Image 3124/3132
Windows driver .inf file - also several Linux problem reports */
[-- Attachment #2: ocz-errors.txt --]
[-- Type: text/plain, Size: 41087 bytes --]
Linux version 2.6.27.7-134.ps10 (root@irian.ms.mff.cuni.cz) (gcc version 4.3.2 20081105 (Red Hat 4.3.2-7) (GCC) ) #1 SMP PREEMPT Mon Dec 15 18:41:12 CET 2008
Command line: ro root=LABEL=IRIAN-LNX gdbe=0 quiet
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009d800 (usable)
BIOS-e820: 000000000009d800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bfeb0000 (usable)
BIOS-e820: 00000000bfeb0000 - 00000000bfecc000 (ACPI data)
BIOS-e820: 00000000bfecc000 - 00000000bff00000 (ACPI NVS)
BIOS-e820: 00000000bff00000 - 00000000c0000000 (reserved)
BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 000000013c000000 (usable)
DMI present.
last_pfn = 0x13c000 max_arch_pfn = 0x3ffffffff
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
last_pfn = 0xbfeb0 max_arch_pfn = 0x3ffffffff
init_memory_mapping
0000000000 - 00bfe00000 page 2M
00bfe00000 - 00bfeb0000 page 4k
kernel direct mapping tables up to bfeb0000 @ 8000-d000
last_map_addr: bfeb0000 end: bfeb0000
init_memory_mapping
0100000000 - 013c000000 page 2M
kernel direct mapping tables up to 13c000000 @ b000-11000
last_map_addr: 13c000000 end: 13c000000
RAMDISK: 37c74000 - 37fef35b
ACPI: RSDP 000F68D0, 0024 (r2 LENOVO)
ACPI: XSDT BFEBB77F, 0094 (r1 LENOVO TP-7L 2190 LTP 0)
ACPI: FACP BFEBB900, 00F4 (r3 LENOVO TP-7L 2190 LNVO 1)
ACPI Warning (tbfadt-0442): Optional field "Gpe1Block" has zero address or length: 000000000000102C/0 [20080609]
ACPI: DSDT BFEBBD1D, FED1 (r1 LENOVO TP-7L 2190 MSFT 3000000)
ACPI: FACS BFEE4000, 0040
ACPI: SSDT BFEBBAB4, 0269 (r1 LENOVO TP-7L 2190 MSFT 3000000)
ACPI: ECDT BFECBBEE, 0052 (r1 LENOVO TP-7L 2190 LNVO 1)
ACPI: TCPA BFECBC40, 0032 (r2 LENOVO TP-7L 2190 LNVO 1)
ACPI: APIC BFECBC72, 0068 (r1 LENOVO TP-7L 2190 LNVO 1)
ACPI: MCFG BFECBCDA, 003C (r1 LENOVO TP-7L 2190 LNVO 1)
ACPI: HPET BFECBD16, 0038 (r1 LENOVO TP-7L 2190 LNVO 1)
ACPI: SLIC BFECBDF0, 0176 (r1 LENOVO TP-7L 2190 LTP 0)
ACPI: BOOT BFECBF66, 0028 (r1 LENOVO TP-7L 2190 LTP 1)
ACPI: ASF! BFECBF8E, 0072 (r16 LENOVO TP-7L 2190 PTL 1)
ACPI: SSDT BFEE26D9, 025F (r1 LENOVO TP-7L 2190 INTL 20050513)
ACPI: SSDT BFEE2938, 00A6 (r1 LENOVO TP-7L 2190 INTL 20050513)
ACPI: SSDT BFEE29DE, 04F7 (r1 LENOVO TP-7L 2190 INTL 20050513)
ACPI: SSDT BFEE2ED5, 01D8 (r1 LENOVO TP-7L 2190 INTL 20050513)
ACPI: DMI detected: Lenovo ThinkPad T61
ACPI: Added _OSI(Linux)
(7 early reservations) ==> bootmem [0000000000 - 013c000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0000200000 - 000070faa4] TEXT DATA BSS ==> [0000200000 - 000070faa4]
#3 [0037c74000 - 0037fef35b] RAMDISK ==> [0037c74000 - 0037fef35b]
#4 [000009d800 - 0000100000] BIOS reserved ==> [000009d800 - 0000100000]
#5 [0000008000 - 000000b000] PGTABLE ==> [0000008000 - 000000b000]
#6 [000000b000 - 000000c000] PGTABLE ==> [000000b000 - 000000c000]
found SMP MP-table at [ffff8800000f6900] 000f6900
[ffffe20000000000-ffffe200045fffff] PMD -> [ffff880028200000-ffff88002c7fffff] on node 0
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x0013c000
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000000 -> 0x0000009d
0: 0x00000100 -> 0x000bfeb0
0: 0x00100000 -> 0x0013c000
On node 0 totalpages: 1031757
DMA zone: 2539 pages, LIFO batch:0
DMA32 zone: 767720 pages, LIFO batch:31
Normal zone: 242400 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 0, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PM: Registered nosave memory: 000000000009d000 - 000000000009e000
PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
PM: Registered nosave memory: 00000000bfeb0000 - 00000000bfecc000
PM: Registered nosave memory: 00000000bfecc000 - 00000000bff00000
PM: Registered nosave memory: 00000000bff00000 - 00000000c0000000
PM: Registered nosave memory: 00000000c0000000 - 00000000f0000000
PM: Registered nosave memory: 00000000f0000000 - 00000000f4000000
PM: Registered nosave memory: 00000000f4000000 - 00000000fec00000
PM: Registered nosave memory: 00000000fec00000 - 00000000fec10000
PM: Registered nosave memory: 00000000fec10000 - 00000000fed00000
PM: Registered nosave memory: 00000000fed00000 - 00000000fed14000
PM: Registered nosave memory: 00000000fed14000 - 00000000fed1a000
PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1c000
PM: Registered nosave memory: 00000000fed1c000 - 00000000fed90000
PM: Registered nosave memory: 00000000fed90000 - 00000000fee00000
PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
PM: Registered nosave memory: 00000000fee01000 - 00000000ff000000
PM: Registered nosave memory: 00000000ff000000 - 0000000100000000
Allocating PCI resources starting at c4000000 (gap: c0000000:30000000)
PERCPU: Allocating 45664 bytes of per cpu data
NR_CPUS: 2, nr_cpu_ids: 2, nr_node_ids 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1012659
Kernel command line: ro root=LABEL=IRIAN-LNX gdbe=0 quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
TSC: PIT calibration confirmed by PMTIMER.
TSC: using PIT calibration value
Detected 1994.954 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
No AGP bridge found
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing software IO TLB between 0x20000000 - 0x24000000
Memory: 3973120k/5177344k available (2879k kernel code, 152916k reserved, 1273k data, 356k init)
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
hpet clockevent registered
Calibrating delay loop (skipped), value calculated using timer frequency.. 3989.90 BogoMIPS (lpj=1994954)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
ACPI: Core revision 20080609
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Duo CPU T7300 @ 2.00GHz stepping 0b
Using local APIC timer interrupts.
APIC timer calibration result 12468497
Detected 12.468 MHz APIC timer.
Booting processor 1/1 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3989.81 BogoMIPS (lpj=1994907)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM)2 Duo CPU T7300 @ 2.00GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#1]:
Measured 1101310 cycles TSC warp between CPUs, turning off TSC clock.
Marking TSC unstable due to check_tsc_sync_source failed
Brought up 2 CPUs
Total of 2 processors activated (7979.72 BogoMIPS).
sizeof(vma)=168 bytes
sizeof(page)=56 bytes
sizeof(inode)=536 bytes
sizeof(dentry)=208 bytes
sizeof(ext3inode)=736 bytes
sizeof(buffer_head)=104 bytes
sizeof(skbuff)=224 bytes
sizeof(task_struct)=1424 bytes
net_namespace: 1184 bytes
NET: Registered protocol family 16
ACPI: ACPI Dock Station Driver
ACPI: \_SB_.PCI0.IDE0.PRIM.MSTR: found ejectable bay
ACPI: \_SB_.PCI0.IDE0.PRIM.MSTR: Adding notify handler
ACPI: Bay [\_SB_.PCI0.IDE0.PRIM.MSTR] Added
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 63
PCI: MCFG area at f0000000 reserved in E820
PCI: Using MMCONFIG at f0000000 - f3ffffff
PCI: Using configuration type 1 for base access
ACPI: EC: EC description table is found, configuring boot EC
ACPI: BIOS _OSI(Linux) query honored via DMI
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x12, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
PCI: 0000:00:19.0 reg 10 32bit mmio: [fe200000, fe21ffff]
PCI: 0000:00:19.0 reg 14 32bit mmio: [fe225000, fe225fff]
PCI: 0000:00:19.0 reg 18 io port: [1840, 185f]
pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
pci 0000:00:19.0: PME# disabled
PCI: 0000:00:1a.0 reg 20 io port: [1860, 187f]
PCI: 0000:00:1a.1 reg 20 io port: [1880, 189f]
PCI: 0000:00:1a.7 reg 10 32bit mmio: [fe226c00, fe226fff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
PCI: 0000:00:1b.0 reg 10 64bit mmio: [fe220000, fe223fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.2: PME# disabled
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
PCI: 0000:00:1d.0 reg 20 io port: [18a0, 18bf]
PCI: 0000:00:1d.1 reg 20 io port: [18c0, 18df]
PCI: 0000:00:1d.2 reg 20 io port: [18e0, 18ff]
PCI: 0000:00:1d.7 reg 10 32bit mmio: [fe227000, fe2273ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
PCI: 0000:00:1f.1 reg 10 io port: [0, 7]
PCI: 0000:00:1f.1 reg 14 io port: [0, 3]
PCI: 0000:00:1f.1 reg 18 io port: [0, 7]
PCI: 0000:00:1f.1 reg 1c io port: [0, 3]
PCI: 0000:00:1f.1 reg 20 io port: [1830, 183f]
PCI: 0000:00:1f.2 reg 10 io port: [1c48, 1c4f]
PCI: 0000:00:1f.2 reg 14 io port: [1c1c, 1c1f]
PCI: 0000:00:1f.2 reg 18 io port: [1c40, 1c47]
PCI: 0000:00:1f.2 reg 1c io port: [1c18, 1c1b]
PCI: 0000:00:1f.2 reg 20 io port: [1c20, 1c3f]
PCI: 0000:00:1f.2 reg 24 32bit mmio: [fe226000, fe2267ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
PCI: 0000:00:1f.3 reg 10 32bit mmio: [fe227400, fe2274ff]
PCI: 0000:00:1f.3 reg 20 io port: [1c60, 1c7f]
PCI: 0000:01:00.0 reg 10 32bit mmio: [d6000000, d6ffffff]
PCI: 0000:01:00.0 reg 14 64bit mmio: [e0000000, efffffff]
PCI: 0000:01:00.0 reg 1c 64bit mmio: [d4000000, d5ffffff]
PCI: 0000:01:00.0 reg 24 io port: [2000, 207f]
PCI: 0000:01:00.0 reg 30 32bit mmio: [0, 1ffff]
PCI: bridge 0000:00:01.0 io port: [2000, 2fff]
PCI: bridge 0000:00:01.0 32bit mmio: [d4000000, d6ffffff]
PCI: bridge 0000:00:01.0 64bit mmio pref: [e0000000, efffffff]
PCI: bridge 0000:00:1c.0 io port: [3000, 3fff]
PCI: bridge 0000:00:1c.0 32bit mmio: [fc000000, fdffffff]
PCI: bridge 0000:00:1c.0 64bit mmio pref: [f8000000, f80fffff]
PCI: 0000:03:00.0 reg 10 64bit mmio: [df2fe000, df2fffff]
pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
pci 0000:03:00.0: PME# disabled
PCI: bridge 0000:00:1c.1 io port: [4000, 4fff]
PCI: bridge 0000:00:1c.1 32bit mmio: [dc100000, df2fffff]
PCI: bridge 0000:00:1c.1 64bit mmio pref: [dfd00000, dfdfffff]
PCI: bridge 0000:00:1c.2 io port: [5000, 5fff]
PCI: bridge 0000:00:1c.2 32bit mmio: [d8000000, d9ffffff]
PCI: bridge 0000:00:1c.2 64bit mmio pref: [dfa00000, dfafffff]
PCI: bridge 0000:00:1c.3 io port: [6000, 6fff]
PCI: bridge 0000:00:1c.3 32bit mmio: [d0000000, d1ffffff]
PCI: bridge 0000:00:1c.3 64bit mmio pref: [df700000, df7fffff]
PCI: bridge 0000:00:1c.4 io port: [7000, 7fff]
PCI: bridge 0000:00:1c.4 32bit mmio: [cc000000, cdffffff]
PCI: bridge 0000:00:1c.4 64bit mmio pref: [df400000, df4fffff]
PCI: 0000:15:00.0 reg 10 32bit mmio: [f8100000, f8100fff]
pci 0000:15:00.0: supports D1
pci 0000:15:00.0: supports D2
pci 0000:15:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:15:00.0: PME# disabled
pci 0000:00:1e.0: transparent bridge
PCI: bridge 0000:00:1e.0 io port: [8000, bfff]
PCI: bridge 0000:00:1e.0 32bit mmio: [f8100000, fbffffff]
PCI: bridge 0000:00:1e.0 64bit mmio pref: [f4000000, f7ffffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 6 7 9 10 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 *6 7 9 10 11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 *10 11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: Power Resource [PUBS] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
Bluetooth: Core ver 2.13
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
PCI-GART: No AMD northbridge found.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
tracer: 1286 pages allocated for 65536 entries of 80 bytes
actual entries 65586
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0xc0000-0xc3fff has been reserved
system 00:00: iomem range 0xc4000-0xc7fff has been reserved
system 00:00: iomem range 0xc8000-0xcbfff has been reserved
system 00:00: iomem range 0xcc000-0xcffff has been reserved
system 00:00: iomem range 0xe0000-0xe3fff could not be reserved
system 00:00: iomem range 0xe4000-0xe7fff could not be reserved
system 00:00: iomem range 0xe8000-0xebfff could not be reserved
system 00:00: iomem range 0xec000-0xeffff could not be reserved
system 00:00: iomem range 0xf0000-0xfffff could not be reserved
system 00:00: iomem range 0x100000-0xbfffffff could not be reserved
system 00:00: iomem range 0xfec00000-0xfed3ffff could not be reserved
system 00:00: iomem range 0xfed4c000-0xffffffff could not be reserved
system 00:02: ioport range 0x164e-0x164f has been reserved
system 00:02: ioport range 0x1000-0x107f has been reserved
system 00:02: ioport range 0x1180-0x11bf has been reserved
system 00:02: ioport range 0x800-0x80f has been reserved
system 00:02: ioport range 0x15e0-0x15ef has been reserved
system 00:02: ioport range 0x1600-0x165f could not be reserved
system 00:02: iomem range 0xf0000000-0xf3ffffff could not be reserved
system 00:02: iomem range 0xfed1c000-0xfed1ffff could not be reserved
system 00:02: iomem range 0xfed14000-0xfed17fff could not be reserved
system 00:02: iomem range 0xfed18000-0xfed18fff could not be reserved
system 00:02: iomem range 0xfed19000-0xfed19fff could not be reserved
system 00:02: iomem range 0xfed45000-0xfed4bfff could not be reserved
pci 0000:01:00.0: BAR 6: can't allocate mem resource [0xf0000000-0xefffffff]
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0x2000-0x2fff
pci 0000:00:01.0: MEM window: 0xd4000000-0xd6ffffff
pci 0000:00:01.0: PREFETCH window: 0x000000e0000000-0x000000efffffff
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0: IO window: 0x3000-0x3fff
pci 0000:00:1c.0: MEM window: 0xfc000000-0xfdffffff
pci 0000:00:1c.0: PREFETCH window: 0x000000f8000000-0x000000f80fffff
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.1: IO window: 0x4000-0x4fff
pci 0000:00:1c.1: MEM window: 0xdc100000-0xdf2fffff
pci 0000:00:1c.1: PREFETCH window: 0x000000dfd00000-0x000000dfdfffff
pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04
pci 0000:00:1c.2: IO window: 0x5000-0x5fff
pci 0000:00:1c.2: MEM window: 0xd8000000-0xd9ffffff
pci 0000:00:1c.2: PREFETCH window: 0x000000dfa00000-0x000000dfafffff
pci 0000:00:1c.3: PCI bridge, secondary bus 0000:05
pci 0000:00:1c.3: IO window: 0x6000-0x6fff
pci 0000:00:1c.3: MEM window: 0xd0000000-0xd1ffffff
pci 0000:00:1c.3: PREFETCH window: 0x000000df700000-0x000000df7fffff
pci 0000:00:1c.4: PCI bridge, secondary bus 0000:0d
pci 0000:00:1c.4: IO window: 0x7000-0x7fff
pci 0000:00:1c.4: MEM window: 0xcc000000-0xcdffffff
pci 0000:00:1c.4: PREFETCH window: 0x000000df400000-0x000000df4fffff
pci 0000:15:00.0: CardBus bridge, secondary bus 0000:16
pci 0000:15:00.0: IO window: 0x008000-0x0080ff
pci 0000:15:00.0: IO window: 0x008400-0x0084ff
pci 0000:15:00.0: PREFETCH window: 0xf4000000-0xf7ffffff
pci 0000:15:00.0: MEM window: 0xc4000000-0xc7ffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:15
pci 0000:00:1e.0: IO window: 0x8000-0xbfff
pci 0000:00:1e.0: MEM window: 0xf8100000-0xfbffffff
pci 0000:00:1e.0: PREFETCH window: 0x000000f4000000-0x000000f7ffffff
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1c.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
pci 0000:00:1c.2: setting latency timer to 64
pci 0000:00:1c.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1c.4: PCI INT A -> GSI 20 (level, low) -> IRQ 20
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:00:1e.0: enabling device (0005 -> 0007)
pci 0000:00:1e.0: setting latency timer to 64
pci 0000:15:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffffffffffff]
bus: 01 index 0 io port: [2000, 2fff]
bus: 01 index 1 mmio: [d4000000, d6ffffff]
bus: 01 index 2 mmio: [e0000000, efffffff]
bus: 01 index 3 mmio: [0, 0]
bus: 02 index 0 io port: [3000, 3fff]
bus: 02 index 1 mmio: [fc000000, fdffffff]
bus: 02 index 2 mmio: [f8000000, f80fffff]
bus: 02 index 3 mmio: [0, 0]
bus: 03 index 0 io port: [4000, 4fff]
bus: 03 index 1 mmio: [dc100000, df2fffff]
bus: 03 index 2 mmio: [dfd00000, dfdfffff]
bus: 03 index 3 mmio: [0, 0]
bus: 04 index 0 io port: [5000, 5fff]
bus: 04 index 1 mmio: [d8000000, d9ffffff]
bus: 04 index 2 mmio: [dfa00000, dfafffff]
bus: 04 index 3 mmio: [0, 0]
bus: 05 index 0 io port: [6000, 6fff]
bus: 05 index 1 mmio: [d0000000, d1ffffff]
bus: 05 index 2 mmio: [df700000, df7fffff]
bus: 05 index 3 mmio: [0, 0]
bus: 0d index 0 io port: [7000, 7fff]
bus: 0d index 1 mmio: [cc000000, cdffffff]
bus: 0d index 2 mmio: [df400000, df4fffff]
bus: 0d index 3 mmio: [0, 0]
bus: 15 index 0 io port: [8000, bfff]
bus: 15 index 1 mmio: [f8100000, fbffffff]
bus: 15 index 2 mmio: [f4000000, f7ffffff]
bus: 15 index 3 io port: [0, ffff]
bus: 15 index 4 mmio: [0, ffffffffffffffff]
bus: 16 index 0 io port: [8000, 80ff]
bus: 16 index 1 io port: [8400, 84ff]
bus: 16 index 2 mmio: [f4000000, f7ffffff]
bus: 16 index 3 mmio: [c4000000, c7ffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Freeing initrd memory: 3564k freed
Simple Boot Flag at 0x35 set to 0x1
audit: initializing netlink socket (disabled)
type=2000 audit(1229371693.449:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
msgmni has been set to 7768
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered (default)
io scheduler cfq registered
pci 0000:01:00.0: Boot video device
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:01.0: found MSI capability
pci_express 0000:00:01.0:pcie00: allocate port service
pci_express 0000:00:01.0:pcie02: allocate port service
pci_express 0000:00:01.0:pcie03: allocate port service
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: found MSI capability
pci_express 0000:00:1c.0:pcie00: allocate port service
pci_express 0000:00:1c.0:pcie02: allocate port service
pci_express 0000:00:1c.0:pcie03: allocate port service
pcieport-driver 0000:00:1c.1: setting latency timer to 64
pcieport-driver 0000:00:1c.1: found MSI capability
pci_express 0000:00:1c.1:pcie00: allocate port service
pci_express 0000:00:1c.1:pcie02: allocate port service
pci_express 0000:00:1c.1:pcie03: allocate port service
pcieport-driver 0000:00:1c.2: setting latency timer to 64
pcieport-driver 0000:00:1c.2: found MSI capability
pci_express 0000:00:1c.2:pcie00: allocate port service
pci_express 0000:00:1c.2:pcie02: allocate port service
pci_express 0000:00:1c.2:pcie03: allocate port service
pcieport-driver 0000:00:1c.3: setting latency timer to 64
pcieport-driver 0000:00:1c.3: found MSI capability
pci_express 0000:00:1c.3:pcie00: allocate port service
pci_express 0000:00:1c.3:pcie02: allocate port service
pci_express 0000:00:1c.3:pcie03: allocate port service
pcieport-driver 0000:00:1c.4: setting latency timer to 64
pcieport-driver 0000:00:1c.4: found MSI capability
pci_express 0000:00:1c.4:pcie00: allocate port service
pci_express 0000:00:1c.4:pcie02: allocate port service
pci_express 0000:00:1c.4:pcie03: allocate port service
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
ACPI: Sleep Button (CM) [SLPB]
acpi device:03: registered as cooling_device0
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/input/input3
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
acpi device:08: registered as cooling_device1
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:06/device:07/input/input4
ACPI: Video Device [VID1] (multi-head: yes rom: no post: no)
ACPI: SSDT BFEE1B32, 02C4 (r1 PmRef Cpu0Ist 100 INTL 20050513)
ACPI: SSDT BFEE1E7B, 085E (r1 PmRef Cpu0Cst 100 INTL 20050513)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI0007:00: registered as cooling_device2
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT BFEE1A6A, 00C8 (r1 PmRef Cpu1Ist 100 INTL 20050513)
ACPI: SSDT BFEE1DF6, 0085 (r1 PmRef Cpu1Cst 100 INTL 20050513)
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI0007:01: registered as cooling_device3
ACPI: Processor [CPU1] (supports 8 throttling states)
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THM0] (37 C)
thermal LNXTHERM:02: registered as thermal_zone1
ACPI: Thermal Zone [THM1] (38 C)
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
tpm_tis 00:0a: 1.2 TPM (device-id 0x3203, rev-id 9)
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
thinkpad_acpi: ThinkPad ACPI Extras v0.21
thinkpad_acpi: http://ibm-acpi.sf.net/
thinkpad_acpi: ThinkPad BIOS 7LETB9WW (2.19 ), EC 7KHT24WW-1.08
thinkpad_acpi: Lenovo ThinkPad T61, model 88892MG
thinkpad_acpi: radio switch found; radios are enabled
thinkpad_acpi: This ThinkPad has standard ACPI backlight brightness control, supported by the ACPI video driver
thinkpad_acpi: Disabling thinkpad-acpi brightness events by default...
Registered led device: tpacpi::thinklight
Registered led device: tpacpi::power
Registered led device: tpacpi:orange:batt
Registered led device: tpacpi:green:batt
Registered led device: tpacpi::dock_active
Registered led device: tpacpi::bay_active
Registered led device: tpacpi::dock_batt
Registered led device: tpacpi::unknown_led
Registered led device: tpacpi::standby
thinkpad_acpi: Lenovo BIOS switched to ACPI backlight control mode
thinkpad_acpi: standard ACPI backlight interface available, not loading native one...
input: ThinkPad Extra Buttons as /devices/virtual/input/input5
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
usbcore: registered new interface driver usblp
usbcore: registered new interface driver libusual
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input6
input: PC Speaker as /devices/platform/pcspkr/input/input7
IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/input/input8
i2c /dev entries driver
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.17.
ALSA device list:
No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Freeing unused kernel memory: 356k freed
Write protecting the kernel read-only data: 3876k
ehci_hcd 0000:00:1a.7: power state changed by ACPI to D0
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 22, io mem 0xfe226c00
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
Clocksource tsc unstable (delta = -350560033 ns)
ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xfe227000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001860
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: power state changed by ACPI to D0
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001880
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 16, io base 0x000018a0
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 3-1: new full speed USB device using uhci_hcd and address 2
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 17, io base 0x000018c0
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
usb 3-1: configuration #1 chosen from 1 choice
usb 3-2: new full speed USB device using uhci_hcd and address 3
uhci_hcd 0000:00:1d.2: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018e0
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 16 (level, low) -> IRQ 16
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 1.5 Gbps 0x5 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
ata1: SATA max UDMA/133 abar m2048@0xfe226000 port 0xfe226100 irq 16
ata2: DUMMY
ata3: SATA max UDMA/133 abar m2048@0xfe226000 port 0xfe226200 irq 16
usb 3-2: configuration #1 chosen from 1 choice
usb 6-2: new full speed USB device using uhci_hcd and address 2
usb 6-2: configuration #1 chosen from 1 choice
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ATA-8: OCZ CORE_SSD, 02.10104, max UDMA/100
ata1.00: 504856576 sectors, multi 0: LBA48 NCQ (depth 1)
ata1.00: applying bridge limits
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: configured for UDMA/100
ata1.00: configured for UDMA/100
ata1: EH complete
ata3: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA OCZ CORE_SSD 02.1 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 504856576 512-byte hardware sectors (258487 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 504856576 512-byte hardware sectors (258487 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
ata_piix 0000:00:1f.1: version 2.12
ata_piix 0000:00:1f.1: PCI INT C -> GSI 16 (level, low) -> IRQ 16
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi3 : ata_piix
scsi4 : ata_piix
ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1830 irq 14
ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1838 irq 15
ata4.00: ATAPI: Optiarc DVD RW AD-7910A, 1.D1, max UDMA/33
ata4.00: configured for UDMA/33
ata5: port disabled. ignoring.
scsi 3:0:0:0: CD-ROM Optiarc DVD RW AD-7910A 1.D1 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
EXT4-fs: barriers enabled
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem with ordered data mode.
kjournald2 starting. Commit interval 600 seconds
udev: starting version 135
Bluetooth: Generic Bluetooth USB driver ver 0.3
usbcore: registered new interface driver btusb
e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k6
e1000e: Copyright (c) 1999-2008 Intel Corporation.
e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
e1000e 0000:00:19.0: setting latency timer to 64
0000:00:19.0: 0000:00:19.0: Failed to initialize MSI interrupts. Falling back to legacy interrupts.
iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27ks
iwlagn: Copyright(c) 2003-2008 Intel Corporation
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
iTCO_wdt: Found a ICH8M-E TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=1)
nvidia: module license 'NVIDIA' taints kernel.
0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1e:37:1e:82:3b
0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
0000:00:19.0: eth0: MAC: 5, PHY: 6, PBA No: ffffff-0ff
iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
iwlagn 0000:03:00.0: setting latency timer to 64
iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
i801_smbus 0000:00:1f.3: PCI INT A -> GSI 23 (level, low) -> IRQ 23
HDA Intel 0000:00:1b.0: PCI INT B -> GSI 17 (level, low) -> IRQ 17
hda_intel: probe_mask set to 0x1 for device 17aa:20ac
HDA Intel 0000:00:1b.0: setting latency timer to 64
iwlagn: Tunable channels: 13 802.11bg, 19 802.11a channels
iwlagn 0000:03:00.0: PCI INT A disabled
phy0: Selected rate control algorithm 'iwl-agn-rs'
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 180.16 Fri Dec 12 11:09:03 PST 2008
EXT4 FS on dm-0, internal journal on dm-0:8
EXT4-fs: barriers disabled
kjournald2 starting. Commit interval 600 seconds
EXT4 FS on dm-1, internal journal on dm-1:8
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem with ordered data mode.
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
firmware: requesting intel-ucode/06-0f-0b
firmware: requesting intel-ucode/06-0f-0b
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
fuse init (API version 7.9)
Bluetooth: L2CAP ver 2.11
Bluetooth: L2CAP socket layer initialized
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bridge firewalling registered
pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.10
JBD: barrier-based sync failed on dm-0:8 - disabling barriers
input: Virtual ThinkFinger Keyboard as /devices/virtual/input/input9
ata1.00: exception Emask 0x2 SAct 0x1 SErr 0x2000000 action 0x6 frozen
ata1.00: irq_stat 0x00000010, unknown FIS 00000000 00000000 00000000 00000000
ata1: SError: { UnrecFIS }
ata1.00: cmd 61/00:00:b8:ed:ff/01:00:05:00:00/40 tag 0 ncq 131072 out
res 40/00:00:b8:ed:ff/00:00:05:00:00/40 Emask 0x2 (HSM violation)
ata1.00: status: { DRDY }
ata1: hard resetting link
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: configured for UDMA/100
ata1.00: configured for UDMA/100
ata1: EH complete
ata1.00: exception Emask 0x2 SAct 0x1 SErr 0x2000000 action 0x6 frozen
ata1.00: irq_stat 0x00000010, unknown FIS 00000000 00000000 00000000 00000000
ata1: SError: { UnrecFIS }
ata1.00: cmd 61/00:00:b8:ed:ff/01:00:05:00:00/40 tag 0 ncq 131072 out
res 40/00:00:b8:ed:ff/00:00:05:00:00/40 Emask 0x2 (HSM violation)
ata1.00: status: { DRDY }
ata1: hard resetting link
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: configured for UDMA/100
ata1.00: configured for UDMA/100
ata1: EH complete
ata1.00: exception Emask 0x2 SAct 0x1 SErr 0x2000000 action 0x6 frozen
ata1.00: irq_stat 0x00000010, unknown FIS 00000000 00000000 00000000 00000000
ata1: SError: { UnrecFIS }
ata1.00: cmd 61/00:00:b8:ed:ff/01:00:05:00:00/40 tag 0 ncq 131072 out
res 40/00:00:b8:ed:ff/00:00:05:00:00/40 Emask 0x2 (HSM violation)
ata1.00: status: { DRDY }
ata1: hard resetting link
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: configured for UDMA/100
ata1.00: configured for UDMA/100
ata1: EH complete
ata1.00: NCQ disabled due to excessive errors
ata1.00: exception Emask 0x2 SAct 0x1 SErr 0x2000000 action 0x6 frozen
ata1.00: irq_stat 0x00000010, unknown FIS 00000000 00000000 00000000 00000000
ata1: SError: { UnrecFIS }
ata1.00: cmd 61/00:00:b8:ed:ff/01:00:05:00:00/40 tag 0 ncq 131072 out
res 40/00:00:b8:ed:ff/00:00:05:00:00/40 Emask 0x2 (HSM violation)
ata1.00: status: { DRDY }
ata1: hard resetting link
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: configured for UDMA/100
ata1.00: configured for UDMA/100
ata1: EH complete
sd 0:0:0:0: [sda] 504856576 512-byte hardware sectors (258487 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 504856576 512-byte hardware sectors (258487 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
CE: hpet increasing min_delta_ns to 15000 nsec
input: Virtual ThinkFinger Keyboard as /devices/virtual/input/input10
[-- Attachment #3: ocz-hdparm.txt --]
[-- Type: text/plain, Size: 1534 bytes --]
/dev/sda:
ATA device, with non-removable media
Model Number: OCZ CORE_SSD
Serial Number: DC03084908560001D
Firmware Revision: 02.10104
Standards:
Used: ATA/ATAPI-7 T13 1532D revision 4a
Supported: 8 7 6 5 & some of 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 504856576
device size with M = 1024*1024: 246512 MBytes
device size with M = 1000*1000: 258486 MBytes (258 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 1
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 1 Current = ?
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
* Power Management feature set
* Write cache
Look-ahead
* 48-bit Address feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* SATA-I signaling speed (1.5Gb/s)
* SATA-II signaling speed (3.0Gb/s)
* Native Command Queueing (NCQ)
DMA Setup Auto-Activate optimization
Checksum: correct
[-- Attachment #4: ocz-noerrors.txt --]
[-- Type: text/plain, Size: 37709 bytes --]
Linux version 2.6.27.7-134.ps10 (root@irian.ms.mff.cuni.cz) (gcc version 4.3.2 20081105 (Red Hat 4.3.2-7) (GCC) ) #2 SMP PREEMPT Mon Dec 15 21:20:46 CET 2008
Command line: ro root=LABEL=IRIAN-LNX gdbe=0 quiet
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009d800 (usable)
BIOS-e820: 000000000009d800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bfeb0000 (usable)
BIOS-e820: 00000000bfeb0000 - 00000000bfecc000 (ACPI data)
BIOS-e820: 00000000bfecc000 - 00000000bff00000 (ACPI NVS)
BIOS-e820: 00000000bff00000 - 00000000c0000000 (reserved)
BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 000000013c000000 (usable)
DMI present.
last_pfn = 0x13c000 max_arch_pfn = 0x3ffffffff
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
last_pfn = 0xbfeb0 max_arch_pfn = 0x3ffffffff
init_memory_mapping
0000000000 - 00bfe00000 page 2M
00bfe00000 - 00bfeb0000 page 4k
kernel direct mapping tables up to bfeb0000 @ 8000-d000
last_map_addr: bfeb0000 end: bfeb0000
init_memory_mapping
0100000000 - 013c000000 page 2M
kernel direct mapping tables up to 13c000000 @ b000-11000
last_map_addr: 13c000000 end: 13c000000
RAMDISK: 37c74000 - 37fef5c3
ACPI: RSDP 000F68D0, 0024 (r2 LENOVO)
ACPI: XSDT BFEBB77F, 0094 (r1 LENOVO TP-7L 2190 LTP 0)
ACPI: FACP BFEBB900, 00F4 (r3 LENOVO TP-7L 2190 LNVO 1)
ACPI Warning (tbfadt-0442): Optional field "Gpe1Block" has zero address or length: 000000000000102C/0 [20080609]
ACPI: DSDT BFEBBD1D, FED1 (r1 LENOVO TP-7L 2190 MSFT 3000000)
ACPI: FACS BFEE4000, 0040
ACPI: SSDT BFEBBAB4, 0269 (r1 LENOVO TP-7L 2190 MSFT 3000000)
ACPI: ECDT BFECBBEE, 0052 (r1 LENOVO TP-7L 2190 LNVO 1)
ACPI: TCPA BFECBC40, 0032 (r2 LENOVO TP-7L 2190 LNVO 1)
ACPI: APIC BFECBC72, 0068 (r1 LENOVO TP-7L 2190 LNVO 1)
ACPI: MCFG BFECBCDA, 003C (r1 LENOVO TP-7L 2190 LNVO 1)
ACPI: HPET BFECBD16, 0038 (r1 LENOVO TP-7L 2190 LNVO 1)
ACPI: SLIC BFECBDF0, 0176 (r1 LENOVO TP-7L 2190 LTP 0)
ACPI: BOOT BFECBF66, 0028 (r1 LENOVO TP-7L 2190 LTP 1)
ACPI: ASF! BFECBF8E, 0072 (r16 LENOVO TP-7L 2190 PTL 1)
ACPI: SSDT BFEE26D9, 025F (r1 LENOVO TP-7L 2190 INTL 20050513)
ACPI: SSDT BFEE2938, 00A6 (r1 LENOVO TP-7L 2190 INTL 20050513)
ACPI: SSDT BFEE29DE, 04F7 (r1 LENOVO TP-7L 2190 INTL 20050513)
ACPI: SSDT BFEE2ED5, 01D8 (r1 LENOVO TP-7L 2190 INTL 20050513)
ACPI: DMI detected: Lenovo ThinkPad T61
ACPI: Added _OSI(Linux)
(7 early reservations) ==> bootmem [0000000000 - 013c000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0000200000 - 000070faa4] TEXT DATA BSS ==> [0000200000 - 000070faa4]
#3 [0037c74000 - 0037fef5c3] RAMDISK ==> [0037c74000 - 0037fef5c3]
#4 [000009d800 - 0000100000] BIOS reserved ==> [000009d800 - 0000100000]
#5 [0000008000 - 000000b000] PGTABLE ==> [0000008000 - 000000b000]
#6 [000000b000 - 000000c000] PGTABLE ==> [000000b000 - 000000c000]
found SMP MP-table at [ffff8800000f6900] 000f6900
[ffffe20000000000-ffffe200045fffff] PMD -> [ffff880028200000-ffff88002c7fffff] on node 0
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x0013c000
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000000 -> 0x0000009d
0: 0x00000100 -> 0x000bfeb0
0: 0x00100000 -> 0x0013c000
On node 0 totalpages: 1031757
DMA zone: 2539 pages, LIFO batch:0
DMA32 zone: 767720 pages, LIFO batch:31
Normal zone: 242400 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 0, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PM: Registered nosave memory: 000000000009d000 - 000000000009e000
PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
PM: Registered nosave memory: 00000000bfeb0000 - 00000000bfecc000
PM: Registered nosave memory: 00000000bfecc000 - 00000000bff00000
PM: Registered nosave memory: 00000000bff00000 - 00000000c0000000
PM: Registered nosave memory: 00000000c0000000 - 00000000f0000000
PM: Registered nosave memory: 00000000f0000000 - 00000000f4000000
PM: Registered nosave memory: 00000000f4000000 - 00000000fec00000
PM: Registered nosave memory: 00000000fec00000 - 00000000fec10000
PM: Registered nosave memory: 00000000fec10000 - 00000000fed00000
PM: Registered nosave memory: 00000000fed00000 - 00000000fed14000
PM: Registered nosave memory: 00000000fed14000 - 00000000fed1a000
PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1c000
PM: Registered nosave memory: 00000000fed1c000 - 00000000fed90000
PM: Registered nosave memory: 00000000fed90000 - 00000000fee00000
PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
PM: Registered nosave memory: 00000000fee01000 - 00000000ff000000
PM: Registered nosave memory: 00000000ff000000 - 0000000100000000
Allocating PCI resources starting at c4000000 (gap: c0000000:30000000)
PERCPU: Allocating 45664 bytes of per cpu data
NR_CPUS: 2, nr_cpu_ids: 2, nr_node_ids 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1012659
Kernel command line: ro root=LABEL=IRIAN-LNX gdbe=0 quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
TSC: PIT calibration confirmed by PMTIMER.
TSC: using PIT calibration value
Detected 1994.977 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
No AGP bridge found
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing software IO TLB between 0x20000000 - 0x24000000
Memory: 3973120k/5177344k available (2879k kernel code, 152916k reserved, 1273k data, 356k init)
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
hpet clockevent registered
Calibrating delay loop (skipped), value calculated using timer frequency.. 3989.95 BogoMIPS (lpj=1994977)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
ACPI: Core revision 20080609
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Duo CPU T7300 @ 2.00GHz stepping 0b
Using local APIC timer interrupts.
APIC timer calibration result 12468641
Detected 12.468 MHz APIC timer.
Booting processor 1/1 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3989.82 BogoMIPS (lpj=1994911)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM)2 Duo CPU T7300 @ 2.00GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#1]:
Measured 363620 cycles TSC warp between CPUs, turning off TSC clock.
Marking TSC unstable due to check_tsc_sync_source failed
Brought up 2 CPUs
Total of 2 processors activated (7979.77 BogoMIPS).
sizeof(vma)=168 bytes
sizeof(page)=56 bytes
sizeof(inode)=536 bytes
sizeof(dentry)=208 bytes
sizeof(ext3inode)=736 bytes
sizeof(buffer_head)=104 bytes
sizeof(skbuff)=224 bytes
sizeof(task_struct)=1424 bytes
net_namespace: 1184 bytes
NET: Registered protocol family 16
ACPI: ACPI Dock Station Driver
ACPI: \_SB_.PCI0.IDE0.PRIM.MSTR: found ejectable bay
ACPI: \_SB_.PCI0.IDE0.PRIM.MSTR: Adding notify handler
ACPI: Bay [\_SB_.PCI0.IDE0.PRIM.MSTR] Added
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 63
PCI: MCFG area at f0000000 reserved in E820
PCI: Using MMCONFIG at f0000000 - f3ffffff
PCI: Using configuration type 1 for base access
ACPI: EC: EC description table is found, configuring boot EC
ACPI: BIOS _OSI(Linux) query honored via DMI
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x12, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
PCI: 0000:00:19.0 reg 10 32bit mmio: [fe200000, fe21ffff]
PCI: 0000:00:19.0 reg 14 32bit mmio: [fe225000, fe225fff]
PCI: 0000:00:19.0 reg 18 io port: [1840, 185f]
pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
pci 0000:00:19.0: PME# disabled
PCI: 0000:00:1a.0 reg 20 io port: [1860, 187f]
PCI: 0000:00:1a.1 reg 20 io port: [1880, 189f]
PCI: 0000:00:1a.7 reg 10 32bit mmio: [fe226c00, fe226fff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
PCI: 0000:00:1b.0 reg 10 64bit mmio: [fe220000, fe223fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.2: PME# disabled
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
PCI: 0000:00:1d.0 reg 20 io port: [18a0, 18bf]
PCI: 0000:00:1d.1 reg 20 io port: [18c0, 18df]
PCI: 0000:00:1d.2 reg 20 io port: [18e0, 18ff]
PCI: 0000:00:1d.7 reg 10 32bit mmio: [fe227000, fe2273ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
PCI: 0000:00:1f.1 reg 10 io port: [0, 7]
PCI: 0000:00:1f.1 reg 14 io port: [0, 3]
PCI: 0000:00:1f.1 reg 18 io port: [0, 7]
PCI: 0000:00:1f.1 reg 1c io port: [0, 3]
PCI: 0000:00:1f.1 reg 20 io port: [1830, 183f]
PCI: 0000:00:1f.2 reg 10 io port: [1c48, 1c4f]
PCI: 0000:00:1f.2 reg 14 io port: [1c1c, 1c1f]
PCI: 0000:00:1f.2 reg 18 io port: [1c40, 1c47]
PCI: 0000:00:1f.2 reg 1c io port: [1c18, 1c1b]
PCI: 0000:00:1f.2 reg 20 io port: [1c20, 1c3f]
PCI: 0000:00:1f.2 reg 24 32bit mmio: [fe226000, fe2267ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
PCI: 0000:00:1f.3 reg 10 32bit mmio: [fe227400, fe2274ff]
PCI: 0000:00:1f.3 reg 20 io port: [1c60, 1c7f]
PCI: 0000:01:00.0 reg 10 32bit mmio: [d6000000, d6ffffff]
PCI: 0000:01:00.0 reg 14 64bit mmio: [e0000000, efffffff]
PCI: 0000:01:00.0 reg 1c 64bit mmio: [d4000000, d5ffffff]
PCI: 0000:01:00.0 reg 24 io port: [2000, 207f]
PCI: 0000:01:00.0 reg 30 32bit mmio: [0, 1ffff]
PCI: bridge 0000:00:01.0 io port: [2000, 2fff]
PCI: bridge 0000:00:01.0 32bit mmio: [d4000000, d6ffffff]
PCI: bridge 0000:00:01.0 64bit mmio pref: [e0000000, efffffff]
PCI: bridge 0000:00:1c.0 io port: [3000, 3fff]
PCI: bridge 0000:00:1c.0 32bit mmio: [fc000000, fdffffff]
PCI: bridge 0000:00:1c.0 64bit mmio pref: [f8000000, f80fffff]
PCI: 0000:03:00.0 reg 10 64bit mmio: [df2fe000, df2fffff]
pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
pci 0000:03:00.0: PME# disabled
PCI: bridge 0000:00:1c.1 io port: [4000, 4fff]
PCI: bridge 0000:00:1c.1 32bit mmio: [dc100000, df2fffff]
PCI: bridge 0000:00:1c.1 64bit mmio pref: [dfd00000, dfdfffff]
PCI: bridge 0000:00:1c.2 io port: [5000, 5fff]
PCI: bridge 0000:00:1c.2 32bit mmio: [d8000000, d9ffffff]
PCI: bridge 0000:00:1c.2 64bit mmio pref: [dfa00000, dfafffff]
PCI: bridge 0000:00:1c.3 io port: [6000, 6fff]
PCI: bridge 0000:00:1c.3 32bit mmio: [d0000000, d1ffffff]
PCI: bridge 0000:00:1c.3 64bit mmio pref: [df700000, df7fffff]
PCI: bridge 0000:00:1c.4 io port: [7000, 7fff]
PCI: bridge 0000:00:1c.4 32bit mmio: [cc000000, cdffffff]
PCI: bridge 0000:00:1c.4 64bit mmio pref: [df400000, df4fffff]
PCI: 0000:15:00.0 reg 10 32bit mmio: [f8100000, f8100fff]
pci 0000:15:00.0: supports D1
pci 0000:15:00.0: supports D2
pci 0000:15:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:15:00.0: PME# disabled
pci 0000:00:1e.0: transparent bridge
PCI: bridge 0000:00:1e.0 io port: [8000, bfff]
PCI: bridge 0000:00:1e.0 32bit mmio: [f8100000, fbffffff]
PCI: bridge 0000:00:1e.0 64bit mmio pref: [f4000000, f7ffffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 6 7 9 10 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 *6 7 9 10 11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 *10 11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: Power Resource [PUBS] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
Bluetooth: Core ver 2.13
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
PCI-GART: No AMD northbridge found.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
tracer: 1286 pages allocated for 65536 entries of 80 bytes
actual entries 65586
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0xc0000-0xc3fff has been reserved
system 00:00: iomem range 0xc4000-0xc7fff has been reserved
system 00:00: iomem range 0xc8000-0xcbfff has been reserved
system 00:00: iomem range 0xcc000-0xcffff has been reserved
system 00:00: iomem range 0xe0000-0xe3fff could not be reserved
system 00:00: iomem range 0xe4000-0xe7fff could not be reserved
system 00:00: iomem range 0xe8000-0xebfff could not be reserved
system 00:00: iomem range 0xec000-0xeffff could not be reserved
system 00:00: iomem range 0xf0000-0xfffff could not be reserved
system 00:00: iomem range 0x100000-0xbfffffff could not be reserved
system 00:00: iomem range 0xfec00000-0xfed3ffff could not be reserved
system 00:00: iomem range 0xfed4c000-0xffffffff could not be reserved
system 00:02: ioport range 0x164e-0x164f has been reserved
system 00:02: ioport range 0x1000-0x107f has been reserved
system 00:02: ioport range 0x1180-0x11bf has been reserved
system 00:02: ioport range 0x800-0x80f has been reserved
system 00:02: ioport range 0x15e0-0x15ef has been reserved
system 00:02: ioport range 0x1600-0x165f could not be reserved
system 00:02: iomem range 0xf0000000-0xf3ffffff could not be reserved
system 00:02: iomem range 0xfed1c000-0xfed1ffff could not be reserved
system 00:02: iomem range 0xfed14000-0xfed17fff could not be reserved
system 00:02: iomem range 0xfed18000-0xfed18fff could not be reserved
system 00:02: iomem range 0xfed19000-0xfed19fff could not be reserved
system 00:02: iomem range 0xfed45000-0xfed4bfff could not be reserved
pci 0000:01:00.0: BAR 6: can't allocate mem resource [0xf0000000-0xefffffff]
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0x2000-0x2fff
pci 0000:00:01.0: MEM window: 0xd4000000-0xd6ffffff
pci 0000:00:01.0: PREFETCH window: 0x000000e0000000-0x000000efffffff
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0: IO window: 0x3000-0x3fff
pci 0000:00:1c.0: MEM window: 0xfc000000-0xfdffffff
pci 0000:00:1c.0: PREFETCH window: 0x000000f8000000-0x000000f80fffff
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.1: IO window: 0x4000-0x4fff
pci 0000:00:1c.1: MEM window: 0xdc100000-0xdf2fffff
pci 0000:00:1c.1: PREFETCH window: 0x000000dfd00000-0x000000dfdfffff
pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04
pci 0000:00:1c.2: IO window: 0x5000-0x5fff
pci 0000:00:1c.2: MEM window: 0xd8000000-0xd9ffffff
pci 0000:00:1c.2: PREFETCH window: 0x000000dfa00000-0x000000dfafffff
pci 0000:00:1c.3: PCI bridge, secondary bus 0000:05
pci 0000:00:1c.3: IO window: 0x6000-0x6fff
pci 0000:00:1c.3: MEM window: 0xd0000000-0xd1ffffff
pci 0000:00:1c.3: PREFETCH window: 0x000000df700000-0x000000df7fffff
pci 0000:00:1c.4: PCI bridge, secondary bus 0000:0d
pci 0000:00:1c.4: IO window: 0x7000-0x7fff
pci 0000:00:1c.4: MEM window: 0xcc000000-0xcdffffff
pci 0000:00:1c.4: PREFETCH window: 0x000000df400000-0x000000df4fffff
pci 0000:15:00.0: CardBus bridge, secondary bus 0000:16
pci 0000:15:00.0: IO window: 0x008000-0x0080ff
pci 0000:15:00.0: IO window: 0x008400-0x0084ff
pci 0000:15:00.0: PREFETCH window: 0xf4000000-0xf7ffffff
pci 0000:15:00.0: MEM window: 0xc4000000-0xc7ffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:15
pci 0000:00:1e.0: IO window: 0x8000-0xbfff
pci 0000:00:1e.0: MEM window: 0xf8100000-0xfbffffff
pci 0000:00:1e.0: PREFETCH window: 0x000000f4000000-0x000000f7ffffff
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1c.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
pci 0000:00:1c.2: setting latency timer to 64
pci 0000:00:1c.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1c.4: PCI INT A -> GSI 20 (level, low) -> IRQ 20
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:00:1e.0: enabling device (0005 -> 0007)
pci 0000:00:1e.0: setting latency timer to 64
pci 0000:15:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffffffffffff]
bus: 01 index 0 io port: [2000, 2fff]
bus: 01 index 1 mmio: [d4000000, d6ffffff]
bus: 01 index 2 mmio: [e0000000, efffffff]
bus: 01 index 3 mmio: [0, 0]
bus: 02 index 0 io port: [3000, 3fff]
bus: 02 index 1 mmio: [fc000000, fdffffff]
bus: 02 index 2 mmio: [f8000000, f80fffff]
bus: 02 index 3 mmio: [0, 0]
bus: 03 index 0 io port: [4000, 4fff]
bus: 03 index 1 mmio: [dc100000, df2fffff]
bus: 03 index 2 mmio: [dfd00000, dfdfffff]
bus: 03 index 3 mmio: [0, 0]
bus: 04 index 0 io port: [5000, 5fff]
bus: 04 index 1 mmio: [d8000000, d9ffffff]
bus: 04 index 2 mmio: [dfa00000, dfafffff]
bus: 04 index 3 mmio: [0, 0]
bus: 05 index 0 io port: [6000, 6fff]
bus: 05 index 1 mmio: [d0000000, d1ffffff]
bus: 05 index 2 mmio: [df700000, df7fffff]
bus: 05 index 3 mmio: [0, 0]
bus: 0d index 0 io port: [7000, 7fff]
bus: 0d index 1 mmio: [cc000000, cdffffff]
bus: 0d index 2 mmio: [df400000, df4fffff]
bus: 0d index 3 mmio: [0, 0]
bus: 15 index 0 io port: [8000, bfff]
bus: 15 index 1 mmio: [f8100000, fbffffff]
bus: 15 index 2 mmio: [f4000000, f7ffffff]
bus: 15 index 3 io port: [0, ffff]
bus: 15 index 4 mmio: [0, ffffffffffffffff]
bus: 16 index 0 io port: [8000, 80ff]
bus: 16 index 1 io port: [8400, 84ff]
bus: 16 index 2 mmio: [f4000000, f7ffffff]
bus: 16 index 3 mmio: [c4000000, c7ffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Freeing initrd memory: 3565k freed
Simple Boot Flag at 0x35 set to 0x1
audit: initializing netlink socket (disabled)
type=2000 audit(1229372574.447:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
msgmni has been set to 7768
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered (default)
io scheduler cfq registered
pci 0000:01:00.0: Boot video device
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:01.0: found MSI capability
pci_express 0000:00:01.0:pcie00: allocate port service
pci_express 0000:00:01.0:pcie02: allocate port service
pci_express 0000:00:01.0:pcie03: allocate port service
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: found MSI capability
pci_express 0000:00:1c.0:pcie00: allocate port service
pci_express 0000:00:1c.0:pcie02: allocate port service
pci_express 0000:00:1c.0:pcie03: allocate port service
pcieport-driver 0000:00:1c.1: setting latency timer to 64
pcieport-driver 0000:00:1c.1: found MSI capability
pci_express 0000:00:1c.1:pcie00: allocate port service
pci_express 0000:00:1c.1:pcie02: allocate port service
pci_express 0000:00:1c.1:pcie03: allocate port service
pcieport-driver 0000:00:1c.2: setting latency timer to 64
pcieport-driver 0000:00:1c.2: found MSI capability
pci_express 0000:00:1c.2:pcie00: allocate port service
pci_express 0000:00:1c.2:pcie02: allocate port service
pci_express 0000:00:1c.2:pcie03: allocate port service
pcieport-driver 0000:00:1c.3: setting latency timer to 64
pcieport-driver 0000:00:1c.3: found MSI capability
pci_express 0000:00:1c.3:pcie00: allocate port service
pci_express 0000:00:1c.3:pcie02: allocate port service
pci_express 0000:00:1c.3:pcie03: allocate port service
pcieport-driver 0000:00:1c.4: setting latency timer to 64
pcieport-driver 0000:00:1c.4: found MSI capability
pci_express 0000:00:1c.4:pcie00: allocate port service
pci_express 0000:00:1c.4:pcie02: allocate port service
pci_express 0000:00:1c.4:pcie03: allocate port service
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
ACPI: Sleep Button (CM) [SLPB]
acpi device:03: registered as cooling_device0
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/input/input3
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
acpi device:08: registered as cooling_device1
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:06/device:07/input/input4
ACPI: Video Device [VID1] (multi-head: yes rom: no post: no)
ACPI: SSDT BFEE1B32, 02C4 (r1 PmRef Cpu0Ist 100 INTL 20050513)
ACPI: SSDT BFEE1E7B, 085E (r1 PmRef Cpu0Cst 100 INTL 20050513)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI0007:00: registered as cooling_device2
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT BFEE1A6A, 00C8 (r1 PmRef Cpu1Ist 100 INTL 20050513)
ACPI: SSDT BFEE1DF6, 0085 (r1 PmRef Cpu1Cst 100 INTL 20050513)
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI0007:01: registered as cooling_device3
ACPI: Processor [CPU1] (supports 8 throttling states)
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THM0] (61 C)
thermal LNXTHERM:02: registered as thermal_zone1
ACPI: Thermal Zone [THM1] (59 C)
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
tpm_tis 00:0a: 1.2 TPM (device-id 0x3203, rev-id 9)
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
thinkpad_acpi: ThinkPad ACPI Extras v0.21
thinkpad_acpi: http://ibm-acpi.sf.net/
thinkpad_acpi: ThinkPad BIOS 7LETB9WW (2.19 ), EC 7KHT24WW-1.08
thinkpad_acpi: Lenovo ThinkPad T61, model 88892MG
thinkpad_acpi: radio switch found; radios are enabled
thinkpad_acpi: This ThinkPad has standard ACPI backlight brightness control, supported by the ACPI video driver
thinkpad_acpi: Disabling thinkpad-acpi brightness events by default...
Registered led device: tpacpi::thinklight
Registered led device: tpacpi::power
Registered led device: tpacpi:orange:batt
Registered led device: tpacpi:green:batt
Registered led device: tpacpi::dock_active
Registered led device: tpacpi::bay_active
Registered led device: tpacpi::dock_batt
Registered led device: tpacpi::unknown_led
Registered led device: tpacpi::standby
thinkpad_acpi: Lenovo BIOS switched to ACPI backlight control mode
thinkpad_acpi: standard ACPI backlight interface available, not loading native one...
input: ThinkPad Extra Buttons as /devices/virtual/input/input5
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
usbcore: registered new interface driver usblp
usbcore: registered new interface driver libusual
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input6
input: PC Speaker as /devices/platform/pcspkr/input/input7
IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/input/input8
i2c /dev entries driver
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.17.
ALSA device list:
No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Freeing unused kernel memory: 356k freed
Write protecting the kernel read-only data: 3876k
ehci_hcd 0000:00:1a.7: power state changed by ACPI to D0
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 22, io mem 0xfe226c00
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
Clocksource tsc unstable (delta = -330040297 ns)
ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xfe227000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001860
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: power state changed by ACPI to D0
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001880
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 16, io base 0x000018a0
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 3-1: new full speed USB device using uhci_hcd and address 2
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 17, io base 0x000018c0
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
usb 3-1: configuration #1 chosen from 1 choice
usb 3-2: new full speed USB device using uhci_hcd and address 3
uhci_hcd 0000:00:1d.2: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018e0
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 16 (level, low) -> IRQ 16
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 1.5 Gbps 0x5 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
ata1: SATA max UDMA/133 abar m2048@0xfe226000 port 0xfe226100 irq 16
ata2: DUMMY
ata3: SATA max UDMA/133 abar m2048@0xfe226000 port 0xfe226200 irq 16
usb 3-2: configuration #1 chosen from 1 choice
usb 6-2: new full speed USB device using uhci_hcd and address 2
usb 6-2: configuration #1 chosen from 1 choice
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ATA-8: OCZ CORE_SSD, 02.10104, max UDMA/100
ata1.00: 504856576 sectors, multi 0: LBA48 NCQ (not used)
ata1.00: applying bridge limits
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: configured for UDMA/100
ata1.00: configured for UDMA/100
ata1: EH complete
ata3: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA OCZ CORE_SSD 02.1 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 504856576 512-byte hardware sectors (258487 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 504856576 512-byte hardware sectors (258487 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
ata_piix 0000:00:1f.1: version 2.12
ata_piix 0000:00:1f.1: PCI INT C -> GSI 16 (level, low) -> IRQ 16
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi3 : ata_piix
scsi4 : ata_piix
ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1830 irq 14
ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1838 irq 15
ata4.00: ATAPI: Optiarc DVD RW AD-7910A, 1.D1, max UDMA/33
ata4.00: configured for UDMA/33
ata5: port disabled. ignoring.
scsi 3:0:0:0: CD-ROM Optiarc DVD RW AD-7910A 1.D1 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
EXT4-fs: barriers enabled
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem with ordered data mode.
kjournald2 starting. Commit interval 600 seconds
udev: starting version 135
e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k6
e1000e: Copyright (c) 1999-2008 Intel Corporation.
e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
e1000e 0000:00:19.0: setting latency timer to 64
0000:00:19.0: 0000:00:19.0: Failed to initialize MSI interrupts. Falling back to legacy interrupts.
Bluetooth: Generic Bluetooth USB driver ver 0.3
usbcore: registered new interface driver btusb
iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27ks
iwlagn: Copyright(c) 2003-2008 Intel Corporation
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
iTCO_wdt: Found a ICH8M-E TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=1)
nvidia: module license 'NVIDIA' taints kernel.
0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1e:37:1e:82:3b
0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
0000:00:19.0: eth0: MAC: 5, PHY: 6, PBA No: ffffff-0ff
HDA Intel 0000:00:1b.0: PCI INT B -> GSI 17 (level, low) -> IRQ 17
hda_intel: probe_mask set to 0x1 for device 17aa:20ac
HDA Intel 0000:00:1b.0: setting latency timer to 64
i801_smbus 0000:00:1f.3: PCI INT A -> GSI 23 (level, low) -> IRQ 23
iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
iwlagn 0000:03:00.0: setting latency timer to 64
iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:01:00.0: setting latency timer to 64
iwlagn: Tunable channels: 13 802.11bg, 19 802.11a channels
iwlagn 0000:03:00.0: PCI INT A disabled
phy0: Selected rate control algorithm 'iwl-agn-rs'
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 180.16 Fri Dec 12 11:09:03 PST 2008
EXT4 FS on dm-0, internal journal on dm-0:8
EXT4-fs: barriers disabled
kjournald2 starting. Commit interval 600 seconds
EXT4 FS on dm-1, internal journal on dm-1:8
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem with ordered data mode.
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
firmware: requesting intel-ucode/06-0f-0b
firmware: requesting intel-ucode/06-0f-0b
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
JBD: barrier-based sync failed on dm-0:8 - disabling barriers
fuse init (API version 7.9)
Bluetooth: L2CAP ver 2.11
Bluetooth: L2CAP socket layer initialized
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bridge firewalling registered
pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.10
input: Virtual ThinkFinger Keyboard as /devices/virtual/input/input9
tpb[2396]: segfault at 8 ip 00000034890337ef sp 0000000041183e60 error 4 in libX11.so.6.2.0[3489000000+105000]
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH] libata: blacklist NCQ on OCZ CORE 2 SSD
2008-12-15 21:17 [PATCH] libata: blacklist NCQ on OCZ CORE 2 SSD Lubomír Bulej
@ 2008-12-16 0:36 ` Robert Hancock
[not found] ` <49476EC7.5080201@dsrg.mff.cuni.cz>
2008-12-22 8:14 ` Tejun Heo
1 sibling, 1 reply; 4+ messages in thread
From: Robert Hancock @ 2008-12-16 0:36 UTC (permalink / raw)
To: linux-ide; +Cc: jgarzik
Lubomír Bulej wrote:
> Hello,
>
> after putting a 250G OCZ CORE v2 SSD into my notebook, I have to endure
> several invocations of the ata EH before the kernel decides to disable
> NCQ due too many errors. The drive reports NCQ of depth 1, which is
> probably useless anyway.
>
> The patchlet below saves me the waiting for the completion of several
> ata EH invocations, but I'm not sure if this is the right solution.
> Attached are two dmesg dumps, one with errors and the other with the
> patchlet compiled in. Attached is also "hdparm -I" of the drive.
I suspect it's all we can really do. NCQ depth of 1 isn't entirely
useless, as using NCQ commands still allows the drive to send/request
data for an individual request out of order, which NCQ commands don't
allow. However, in this case it would appear that the device is sending
back a bogus all-zeros FIS to the controller which triggers error handling.
The "applying bridge limits" part is interesting, that would imply the
device's identify data doesn't properly indicate it's actually a SATA
device so the kernel assumes it's a PATA device behind a SATA bridge. I
don't think it's related to the problem but it does suggest that whoever
designed the SATA interface on that thing probably didn't do a ton of
validation on it..
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH] libata: blacklist NCQ on OCZ CORE 2 SSD
[not found] ` <49476EC7.5080201@dsrg.mff.cuni.cz>
@ 2008-12-17 1:04 ` Robert Hancock
0 siblings, 0 replies; 4+ messages in thread
From: Robert Hancock @ 2008-12-17 1:04 UTC (permalink / raw)
To: Lubomír Bulej; +Cc: jgarzik, ide
Lubomír Bulej wrote:
> Hello,
>
> thanks for the insight - I can only (somewhat) parse the simplest of ATA
> errors related to bad sectors :-)
>
>> The "applying bridge limits" part is interesting, that would imply the
>> device's identify data doesn't properly indicate it's actually a SATA
>> device so the kernel assumes it's a PATA device behind a SATA bridge.
>> I don't think it's related to the problem but it does suggest that
>> whoever designed the SATA interface on that thing probably didn't do a
>> ton of validation on it..
>
> It well may be, who knows - there is basically no detailed info on the
> product. Is there a way to find out, apart from taking it apart and
> taking a peek at the chips? :-)
Likely not, but it seems pretty much impossible that it is, if it
reports NCQ support..
>
> BTW, can the kernel assumption of "pata-behind-sata-bridge" cause any
> problems?
It looks like all that does is limit the transfer rate to UDMA5 (which
doesn't actually make any difference if it's really SATA) and limits
maximum sectors per transfer to 200.
>
> Anyway, I guess that's what we get when memory manufacturers (let's say
> assemblers) start delving into persistent storage. I was a bit dazed by
> the "oh so distinguishing" model name/number...
>
>
> Best regards,
> Lubomir
>
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH] libata: blacklist NCQ on OCZ CORE 2 SSD
2008-12-15 21:17 [PATCH] libata: blacklist NCQ on OCZ CORE 2 SSD Lubomír Bulej
2008-12-16 0:36 ` Robert Hancock
@ 2008-12-22 8:14 ` Tejun Heo
1 sibling, 0 replies; 4+ messages in thread
From: Tejun Heo @ 2008-12-22 8:14 UTC (permalink / raw)
To: Lubomír Bulej; +Cc: jgarzik, linux-ide
Lubomír Bulej wrote:
> Hello,
>
> after putting a 250G OCZ CORE v2 SSD into my notebook, I have to endure
> several invocations of the ata EH before the kernel decides to disable
> NCQ due too many errors. The drive reports NCQ of depth 1, which is
> probably useless anyway.
>
> The patchlet below saves me the waiting for the completion of several
> ata EH invocations, but I'm not sure if this is the right solution.
> Attached are two dmesg dumps, one with errors and the other with the
> patchlet compiled in. Attached is also "hdparm -I" of the drive.
Aieee.. these SSDs. Can't they hire someone who actually know ATA
before putting these devices out on the market? :-(
Anyways, I don't think there's much we can do other than blacklisting
it. Can you please resend with proper S-O-B?
--
tejun
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2008-12-22 8:14 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2008-12-15 21:17 [PATCH] libata: blacklist NCQ on OCZ CORE 2 SSD Lubomír Bulej
2008-12-16 0:36 ` Robert Hancock
[not found] ` <49476EC7.5080201@dsrg.mff.cuni.cz>
2008-12-17 1:04 ` Robert Hancock
2008-12-22 8:14 ` Tejun Heo
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.