From: Jiri Slaby <jirislaby@gmail.com>
To: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-kernel@vger.kernel.org, mm-commits@vger.kernel.org,
Greg KH <gregkh@suse.de>, USB list <linux-usb@vger.kernel.org>,
linux-input@vger.kernel.org, Oliver Neukum <oliver@neukum.org>
Subject: Re: dead USB devices after resume [mmotm 2009-02-10-16-35]
Date: Fri, 13 Feb 2009 11:40:04 +0100 [thread overview]
Message-ID: <49954E04.6090008@gmail.com> (raw)
In-Reply-To: <Pine.LNX.4.44L0.0902111009260.3056-100000@iolanthe.rowland.org>
On 02/11/2009 04:53 PM, Alan Stern wrote:
> On Wed, 11 Feb 2009, Jiri Slaby wrote:
>
>> On 02/11/2009 01:36 AM, akpm@linux-foundation.org wrote:
>>> The mm-of-the-moment snapshot 2009-02-10-16-35 has been uploaded
>> Hi,
>>
>> when I resume from suspend, USB mouse and kbd are not responding anymore, no
>> LEDs, nothing. I need to unplug and replug to get it working. This is a
>> regression since mmotm based on 2.6.29-rc2 which is fine.
>>
>> Any ideas before I start bisection?
>
> In theory the lack of S4 support shouldn't cause this to happen.
>
> You might want to build a kernel with CONFIG_USB_DEBUG enabled. The
> extra debugging information should help find the problem.
Here comes the resume part (including unplug, replug). I suspect auto-suspend?
usb usb1: usb resume
ehci_hcd 0000:00:1a.7: resume root hub
hub 1-0:1.0: hub_resume
usb usb2: usb resume
ehci_hcd 0000:00:1d.7: resume root hub
hub 2-0:1.0: hub_resume
usb usb6: usb resume
usb usb6: wakeup_rh
hub 6-0:1.0: hub_reset_resume
hub 6-0:1.0: trying to enable port power on non-switchable hub
uhci_hcd 0000:00:1d.0: port 1 portsc 009b,00
hub 6-0:1.0: port 1: status 0101 change 0003
usb 6-1: finish reset-resume
usb 6-1: reset full speed USB device using uhci_hcd and address 2
usb 6-1: ep0 maxpacket = 8
usb 6-1: manual set_interface for iface 0, alt 0
hub 6-1:1.0: hub_reset_resume
hub 6-1:1.0: enabling power on all ports
hub 6-1:1.0: port 1: status 0101 change 0001
hub 6-1:1.0: port 2: status 0301 change 0001
uhci_hcd 0000:00:1d.0: reserve dev 2 ep81-INT, period 128, phase 0, 12 us
usb 6-1.1: finish reset-resume
usb 6-1.1: reset full speed USB device using uhci_hcd and address 3
usb 6-1.1: ep0 maxpacket = 8
usb 6-1.1: manual set_interface for iface 0, alt 0
usb 6-1.1: manual set_interface for iface 1, alt 0
usb 6-1.2: finish reset-resume
usb 6-1.2: reset low speed USB device using uhci_hcd and address 4
usb 6-1.2: manual set_interface for iface 0, alt 0
Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
hub 6-0:1.0: state 7 ports 2 chg 0002 evt 0002
hub 6-0:1.0: port 1, status 0103, change 0000, 12 Mb/s
hub 6-1:1.0: state 7 ports 3 chg 0006 evt 0004
done.
hub 6-1:1.0: port 1, status 0103, change 0000, 12 Mb/s
hub 6-1:1.0: port 2, status 0303, change 0000, 1.5 Mb/s
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
ehci_hcd 0000:00:1a.7: suspend root hub
hub 2-0:1.0: hub_suspend
usb usb2: bus auto-suspend
ehci_hcd 0000:00:1d.7: suspend root hub
hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:1d.0: port 1 portsc 008a,00
hub 6-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usb 6-1: USB disconnect, address 2
usb 6-1.1: USB disconnect, address 3
usb 6-1.1: unregistering device
usb 6-1.1: usb_disable_device nuking all URBs
usb 6-1.1: unregistering interface 6-1.1:1.0
usb 6-1.1:1.0: uevent
usb 6-1.1: unregistering interface 6-1.1:1.1
usb 6-1.1:1.1: uevent
usb 6-1.1: uevent
usb 6-1.2: USB disconnect, address 4
usb 6-1.2: unregistering device
usb 6-1.2: usb_disable_device nuking all URBs
usb 6-1.2: unregistering interface 6-1.2:1.0
usb 6-1.2:1.0: uevent
usb 6-1.2: uevent
usb 6-1: unregistering device
usb 6-1: usb_disable_device nuking all URBs
uhci_hcd 0000:00:1d.0: shutdown urb ffff88007c8ca540 ep1in-intr
uhci_hcd 0000:00:1d.0: release dev 2 ep81-INT, period 128, phase 0, 12 us
usb 6-1: unregistering interface 6-1:1.0
usb 6-1:1.0: uevent
usb 6-1: uevent
hub 6-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
usb usb2: usb resume
ehci_hcd 0000:00:1d.7: resume root hub
ehci_hcd 0000:00:1d.7: port 1 full speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003801 POWER OWNER sig=j CONNECT
hub 2-0:1.0: hub_resume
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSC
hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:1d.0: port 1 portsc 0093,00
hub 6-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 6-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 6-1: new full speed USB device using uhci_hcd and address 5
usb 6-1: ep0 maxpacket = 8
usb 6-1: default language 0x0409
usb 6-1: New USB device found, idVendor=04b4, idProduct=2050
usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 6-1: Product: GBella Corporation DV Keyboard
usb 6-1: Manufacturer: Bella Corporation
usb 6-1: uevent
usb 6-1: usb_probe_device
usb 6-1: configuration #1 chosen from 1 choice
usb 6-1: adding 6-1:1.0 (config #1, interface 0)
usb 6-1:1.0: uevent
hub 6-1:1.0: usb_probe_interface
hub 6-1:1.0: usb_probe_interface - got id
hub 6-1:1.0: USB hub found
hub 6-1:1.0: 3 ports detected
hub 6-1:1.0: compound device; port removable status: FRR
hub 6-1:1.0: individual port power switching
hub 6-1:1.0: individual port over-current protection
hub 6-1:1.0: power on to power good time: 100ms
hub 6-1:1.0: hub controller current requirement: 25mA
hub 6-1:1.0: 100mA bus power budget for each child
hub 6-1:1.0: local power source is good
hub 6-1:1.0: enabling power on all ports
/home/l/latest/xxx/drivers/usb/core/inode.c: creating file '005'
hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0002
hub 6-1:1.0: port 1: status 0101 change 0001
hub 6-1:1.0: port 2: status 0301 change 0001
uhci_hcd 0000:00:1d.0: reserve dev 5 ep81-INT, period 128, phase 0, 12 us
hub 6-1:1.0: state 7 ports 3 chg 0006 evt 0000
hub 6-1:1.0: port 1, status 0101, change 0000, 12 Mb/s
usb 6-1.1: new full speed USB device using uhci_hcd and address 6
usb 6-1.1: ep0 maxpacket = 8
usb 6-1.1: skipped 1 descriptor after interface
usb 6-1.1: skipped 1 descriptor after interface
usb 6-1.1: default language 0x0409
usb 6-1.1: New USB device found, idVendor=0458, idProduct=004c
usb 6-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 6-1.1: Product: USB Keyboard
usb 6-1.1: Manufacturer: ABBHOME
usb 6-1.1: uevent
usb 6-1.1: usb_probe_device
usb 6-1.1: configuration #1 chosen from 1 choice
usb 6-1.1: adding 6-1.1:1.0 (config #1, interface 0)
usb 6-1.1:1.0: uevent
usbhid 6-1.1:1.0: usb_probe_interface
usbhid 6-1.1:1.0: usb_probe_interface - got id
input: ABBHOME USB Keyboard as
/devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1.1/6-1.1:1.0/input/input13
uhci_hcd 0000:00:1d.0: reserve dev 6 ep81-INT, period 8, phase 4, 17 us
generic-usb 0003:0458:004C.0004: input: USB HID v1.10 Keyboard [ABBHOME USB
Keyboard] on usb-0000:00:1d.0-1.1/input0
usb 6-1.1: adding 6-1.1:1.1 (config #1, interface 1)
usb 6-1.1:1.1: uevent
usbhid 6-1.1:1.1: usb_probe_interface
usbhid 6-1.1:1.1: usb_probe_interface - got id
input: ABBHOME USB Keyboard as
/devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1.1/6-1.1:1.1/input/input14
uhci_hcd 0000:00:1d.0: reserve dev 6 ep82-INT, period 8, phase 4, 17 us
generic-usb 0003:0458:004C.0005: input: USB HID v1.10 Mouse [ABBHOME USB
Keyboard] on usb-0000:00:1d.0-1.1/input1
/home/l/latest/xxx/drivers/usb/core/inode.c: creating file '006'
hub 6-1:1.0: 425mA power budget left
hub 6-1:1.0: port 2, status 0301, change 0000, 1.5 Mb/s
usb 6-1.2: new low speed USB device using uhci_hcd and address 7
usb 6-1.2: skipped 1 descriptor after interface
usb 6-1.2: default language 0x0409
usb 6-1.2: New USB device found, idVendor=045e, idProduct=00f0
usb 6-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 6-1.2: Product: Microsoft � Laser Mouse 6000
usb 6-1.2: Manufacturer: Microsoft Corporation
usb 6-1.2: uevent
usb 6-1.2: usb_probe_device
usb 6-1.2: configuration #1 chosen from 1 choice
usb 6-1.2: adding 6-1.2:1.0 (config #1, interface 0)
usb 6-1.2:1.0: uevent
usbhid 6-1.2:1.0: usb_probe_interface
usbhid 6-1.2:1.0: usb_probe_interface - got id
input: Microsoft Corporation Microsoft � Laser Mouse 6000 as
/devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1.2/6-1.2:1.0/input/input15
uhci_hcd 0000:00:1d.0: reserve dev 7 ep81-INT, period 8, phase 4, 93 us
generic-usb 0003:045E:00F0.0006: input: USB HID v1.11 Mouse [Microsoft
Corporation Microsoft � Laser Mouse 6000] on usb-0000:00:1d.0-1.2/input0
/home/l/latest/xxx/drivers/usb/core/inode.c: creating file '007'
hub 6-1:1.0: 325mA power budget left
hub 6-1:1.0: state 7 ports 3 chg 0000 evt 0004
hub 2-0:1.0: hub_suspend
usb usb2: bus auto-suspend
ehci_hcd 0000:00:1d.7: suspend root hub
WARNING: multiple messages have this Message-ID (diff)
From: Jiri Slaby <jirislaby@gmail.com>
To: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-kernel@vger.kernel.org, mm-commits@vger.kernel.org,
Greg KH <gregkh@suse.de>, USB list <linux-usb@vger.kernel.org>,
linux-input@vger.kernel.org, Oliver Neukum <oliver@neukum.org>
Subject: Re: dead USB devices after resume [mmotm 2009-02-10-16-35]
Date: Fri, 13 Feb 2009 11:40:04 +0100 [thread overview]
Message-ID: <49954E04.6090008@gmail.com> (raw)
In-Reply-To: <Pine.LNX.4.44L0.0902111009260.3056-100000@iolanthe.rowland.org>
On 02/11/2009 04:53 PM, Alan Stern wrote:
> On Wed, 11 Feb 2009, Jiri Slaby wrote:
>
>> On 02/11/2009 01:36 AM, akpm@linux-foundation.org wrote:
>>> The mm-of-the-moment snapshot 2009-02-10-16-35 has been uploaded
>> Hi,
>>
>> when I resume from suspend, USB mouse and kbd are not responding anymore, no
>> LEDs, nothing. I need to unplug and replug to get it working. This is a
>> regression since mmotm based on 2.6.29-rc2 which is fine.
>>
>> Any ideas before I start bisection?
>
> In theory the lack of S4 support shouldn't cause this to happen.
>
> You might want to build a kernel with CONFIG_USB_DEBUG enabled. The
> extra debugging information should help find the problem.
Here comes the resume part (including unplug, replug). I suspect auto-suspend?
usb usb1: usb resume
ehci_hcd 0000:00:1a.7: resume root hub
hub 1-0:1.0: hub_resume
usb usb2: usb resume
ehci_hcd 0000:00:1d.7: resume root hub
hub 2-0:1.0: hub_resume
usb usb6: usb resume
usb usb6: wakeup_rh
hub 6-0:1.0: hub_reset_resume
hub 6-0:1.0: trying to enable port power on non-switchable hub
uhci_hcd 0000:00:1d.0: port 1 portsc 009b,00
hub 6-0:1.0: port 1: status 0101 change 0003
usb 6-1: finish reset-resume
usb 6-1: reset full speed USB device using uhci_hcd and address 2
usb 6-1: ep0 maxpacket = 8
usb 6-1: manual set_interface for iface 0, alt 0
hub 6-1:1.0: hub_reset_resume
hub 6-1:1.0: enabling power on all ports
hub 6-1:1.0: port 1: status 0101 change 0001
hub 6-1:1.0: port 2: status 0301 change 0001
uhci_hcd 0000:00:1d.0: reserve dev 2 ep81-INT, period 128, phase 0, 12 us
usb 6-1.1: finish reset-resume
usb 6-1.1: reset full speed USB device using uhci_hcd and address 3
usb 6-1.1: ep0 maxpacket = 8
usb 6-1.1: manual set_interface for iface 0, alt 0
usb 6-1.1: manual set_interface for iface 1, alt 0
usb 6-1.2: finish reset-resume
usb 6-1.2: reset low speed USB device using uhci_hcd and address 4
usb 6-1.2: manual set_interface for iface 0, alt 0
Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
hub 6-0:1.0: state 7 ports 2 chg 0002 evt 0002
hub 6-0:1.0: port 1, status 0103, change 0000, 12 Mb/s
hub 6-1:1.0: state 7 ports 3 chg 0006 evt 0004
done.
hub 6-1:1.0: port 1, status 0103, change 0000, 12 Mb/s
hub 6-1:1.0: port 2, status 0303, change 0000, 1.5 Mb/s
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
ehci_hcd 0000:00:1a.7: suspend root hub
hub 2-0:1.0: hub_suspend
usb usb2: bus auto-suspend
ehci_hcd 0000:00:1d.7: suspend root hub
hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:1d.0: port 1 portsc 008a,00
hub 6-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usb 6-1: USB disconnect, address 2
usb 6-1.1: USB disconnect, address 3
usb 6-1.1: unregistering device
usb 6-1.1: usb_disable_device nuking all URBs
usb 6-1.1: unregistering interface 6-1.1:1.0
usb 6-1.1:1.0: uevent
usb 6-1.1: unregistering interface 6-1.1:1.1
usb 6-1.1:1.1: uevent
usb 6-1.1: uevent
usb 6-1.2: USB disconnect, address 4
usb 6-1.2: unregistering device
usb 6-1.2: usb_disable_device nuking all URBs
usb 6-1.2: unregistering interface 6-1.2:1.0
usb 6-1.2:1.0: uevent
usb 6-1.2: uevent
usb 6-1: unregistering device
usb 6-1: usb_disable_device nuking all URBs
uhci_hcd 0000:00:1d.0: shutdown urb ffff88007c8ca540 ep1in-intr
uhci_hcd 0000:00:1d.0: release dev 2 ep81-INT, period 128, phase 0, 12 us
usb 6-1: unregistering interface 6-1:1.0
usb 6-1:1.0: uevent
usb 6-1: uevent
hub 6-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
usb usb2: usb resume
ehci_hcd 0000:00:1d.7: resume root hub
ehci_hcd 0000:00:1d.7: port 1 full speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003801 POWER OWNER sig=j CONNECT
hub 2-0:1.0: hub_resume
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSC
hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:1d.0: port 1 portsc 0093,00
hub 6-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 6-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 6-1: new full speed USB device using uhci_hcd and address 5
usb 6-1: ep0 maxpacket = 8
usb 6-1: default language 0x0409
usb 6-1: New USB device found, idVendor=04b4, idProduct=2050
usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 6-1: Product: GBella Corporation DV Keyboard
usb 6-1: Manufacturer: Bella Corporation
usb 6-1: uevent
usb 6-1: usb_probe_device
usb 6-1: configuration #1 chosen from 1 choice
usb 6-1: adding 6-1:1.0 (config #1, interface 0)
usb 6-1:1.0: uevent
hub 6-1:1.0: usb_probe_interface
hub 6-1:1.0: usb_probe_interface - got id
hub 6-1:1.0: USB hub found
hub 6-1:1.0: 3 ports detected
hub 6-1:1.0: compound device; port removable status: FRR
hub 6-1:1.0: individual port power switching
hub 6-1:1.0: individual port over-current protection
hub 6-1:1.0: power on to power good time: 100ms
hub 6-1:1.0: hub controller current requirement: 25mA
hub 6-1:1.0: 100mA bus power budget for each child
hub 6-1:1.0: local power source is good
hub 6-1:1.0: enabling power on all ports
/home/l/latest/xxx/drivers/usb/core/inode.c: creating file '005'
hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0002
hub 6-1:1.0: port 1: status 0101 change 0001
hub 6-1:1.0: port 2: status 0301 change 0001
uhci_hcd 0000:00:1d.0: reserve dev 5 ep81-INT, period 128, phase 0, 12 us
hub 6-1:1.0: state 7 ports 3 chg 0006 evt 0000
hub 6-1:1.0: port 1, status 0101, change 0000, 12 Mb/s
usb 6-1.1: new full speed USB device using uhci_hcd and address 6
usb 6-1.1: ep0 maxpacket = 8
usb 6-1.1: skipped 1 descriptor after interface
usb 6-1.1: skipped 1 descriptor after interface
usb 6-1.1: default language 0x0409
usb 6-1.1: New USB device found, idVendor=0458, idProduct=004c
usb 6-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 6-1.1: Product: USB Keyboard
usb 6-1.1: Manufacturer: ABBHOME
usb 6-1.1: uevent
usb 6-1.1: usb_probe_device
usb 6-1.1: configuration #1 chosen from 1 choice
usb 6-1.1: adding 6-1.1:1.0 (config #1, interface 0)
usb 6-1.1:1.0: uevent
usbhid 6-1.1:1.0: usb_probe_interface
usbhid 6-1.1:1.0: usb_probe_interface - got id
input: ABBHOME USB Keyboard as
/devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1.1/6-1.1:1.0/input/input13
uhci_hcd 0000:00:1d.0: reserve dev 6 ep81-INT, period 8, phase 4, 17 us
generic-usb 0003:0458:004C.0004: input: USB HID v1.10 Keyboard [ABBHOME USB
Keyboard] on usb-0000:00:1d.0-1.1/input0
usb 6-1.1: adding 6-1.1:1.1 (config #1, interface 1)
usb 6-1.1:1.1: uevent
usbhid 6-1.1:1.1: usb_probe_interface
usbhid 6-1.1:1.1: usb_probe_interface - got id
input: ABBHOME USB Keyboard as
/devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1.1/6-1.1:1.1/input/input14
uhci_hcd 0000:00:1d.0: reserve dev 6 ep82-INT, period 8, phase 4, 17 us
generic-usb 0003:0458:004C.0005: input: USB HID v1.10 Mouse [ABBHOME USB
Keyboard] on usb-0000:00:1d.0-1.1/input1
/home/l/latest/xxx/drivers/usb/core/inode.c: creating file '006'
hub 6-1:1.0: 425mA power budget left
hub 6-1:1.0: port 2, status 0301, change 0000, 1.5 Mb/s
usb 6-1.2: new low speed USB device using uhci_hcd and address 7
usb 6-1.2: skipped 1 descriptor after interface
usb 6-1.2: default language 0x0409
usb 6-1.2: New USB device found, idVendor=045e, idProduct=00f0
usb 6-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 6-1.2: Product: Microsoft � Laser Mouse 6000
usb 6-1.2: Manufacturer: Microsoft Corporation
usb 6-1.2: uevent
usb 6-1.2: usb_probe_device
usb 6-1.2: configuration #1 chosen from 1 choice
usb 6-1.2: adding 6-1.2:1.0 (config #1, interface 0)
usb 6-1.2:1.0: uevent
usbhid 6-1.2:1.0: usb_probe_interface
usbhid 6-1.2:1.0: usb_probe_interface - got id
input: Microsoft Corporation Microsoft � Laser Mouse 6000 as
/devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1.2/6-1.2:1.0/input/input15
uhci_hcd 0000:00:1d.0: reserve dev 7 ep81-INT, period 8, phase 4, 93 us
generic-usb 0003:045E:00F0.0006: input: USB HID v1.11 Mouse [Microsoft
Corporation Microsoft � Laser Mouse 6000] on usb-0000:00:1d.0-1.2/input0
/home/l/latest/xxx/drivers/usb/core/inode.c: creating file '007'
hub 6-1:1.0: 325mA power budget left
hub 6-1:1.0: state 7 ports 3 chg 0000 evt 0004
hub 2-0:1.0: hub_suspend
usb usb2: bus auto-suspend
ehci_hcd 0000:00:1d.7: suspend root hub
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2009-02-13 10:40 UTC|newest]
Thread overview: 44+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-02-11 0:36 mmotm 2009-02-10-16-35 uploaded akpm
2009-02-11 8:44 ` dead USB devices after resume [mmotm 2009-02-10-16-35] Jiri Slaby
2009-02-11 8:44 ` Jiri Slaby
2009-02-11 9:44 ` Rafael J. Wysocki
2009-02-11 9:54 ` Jiri Slaby
2009-02-11 9:54 ` Jiri Slaby
2009-02-11 13:38 ` Jiri Slaby
2009-02-11 13:38 ` Jiri Slaby
2009-02-11 21:49 ` Rafael J. Wysocki
2009-02-11 21:49 ` Rafael J. Wysocki
2009-02-11 15:53 ` Alan Stern
2009-02-11 15:53 ` Alan Stern
2009-02-13 10:40 ` Jiri Slaby [this message]
2009-02-13 10:40 ` Jiri Slaby
2009-02-13 15:26 ` Alan Stern
2009-02-13 15:26 ` Alan Stern
2009-02-16 13:50 ` Jiri Slaby
2009-02-16 13:50 ` Jiri Slaby
2009-02-16 19:58 ` Alan Stern
2009-02-16 19:58 ` Alan Stern
2009-02-13 18:19 ` Jiri Kosina
2009-02-11 8:51 ` ACPI: S4 disappeared " Jiri Slaby
2009-02-11 8:51 ` Jiri Slaby
2009-02-11 10:17 ` Jiri Slaby
2009-02-11 15:43 ` Rafael J. Wysocki
2009-02-11 15:43 ` Rafael J. Wysocki
2009-02-11 16:22 ` Ingo Molnar
2009-02-11 16:22 ` Ingo Molnar
2009-02-11 21:22 ` Rafael J. Wysocki
2009-02-11 21:22 ` Rafael J. Wysocki
2009-02-13 9:37 ` Pavel Machek
2009-02-13 9:37 ` Pavel Machek
2009-02-11 10:17 ` Jiri Slaby
2009-02-11 16:48 ` mmotm 2009-02-10-16-35 uploaded Randy Dunlap
2009-02-11 16:58 ` mmotm 2009-02-10-16-35 uploaded (s1d13xfb) Randy Dunlap
2009-02-11 22:01 ` Kristoffer Ericson
2009-02-11 17:06 ` mmotm 2009-02-10-16-35 uploaded (reiser4-quota) Randy Dunlap
2009-02-11 17:13 ` Jan Kara
2009-02-11 17:23 ` Edward Shishkin
2009-02-12 2:49 ` KOSAKI Motohiro
2009-02-12 2:53 ` Andrew Morton
2009-02-20 18:12 ` Zan Lynx
2009-02-20 18:30 ` Andrew Morton
2009-02-12 4:13 ` Volker Armin Hemmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=49954E04.6090008@gmail.com \
--to=jirislaby@gmail.com \
--cc=gregkh@suse.de \
--cc=linux-input@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=mm-commits@vger.kernel.org \
--cc=oliver@neukum.org \
--cc=stern@rowland.harvard.edu \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.