* [linux-dvb] getting started
@ 2009-03-12 21:46 Rolf Schumacher
2009-03-12 22:02 ` Antti Palosaari
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Rolf Schumacher @ 2009-03-12 21:46 UTC (permalink / raw)
To: linux-dvb
I once had my TechnoTrend DVB-C driver working with linux, looking tv.
However, completely forgot how I managed that.
I think I was following the wiki
How to Obtain, Build and Install V4L-DVB Device Driver
I checked out the v4l-dvb sources using Mercurial.
However, a make failed immediately:
------------
make -C /home/rsc/src/v4l-dvb/v4l
make[1]: Entering directory `/home/rsc/src/v4l-dvb/v4l'
Updating/Creating .config
Preparing to compile for kernel version 2.6.28
File not found: /lib/modules/2.6.28-7.slh.3-sidux-686/build/.config at
./scripts/make_kconfig.pl line 32, <IN> line 4.
make[1]: *** Keine Regel vorhanden, um das Target ».myconfig«,
benötigt von »config-compat.h«, zu erstellen. Schluss.
make[1]: Leaving directory `/home/rsc/src/v4l-dvb/v4l'
make: *** [all] Fehler 2
-----------
Am I on the right track?
If so, what is missing?
ngong
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead linux-media@vger.kernel.org
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [linux-dvb] getting started
2009-03-12 21:46 [linux-dvb] getting started Rolf Schumacher
@ 2009-03-12 22:02 ` Antti Palosaari
2009-03-12 22:47 ` Rolf Schumacher
2009-03-12 22:04 ` Thomas Kaiser
2009-03-14 5:14 ` Compro T750F - frontend initialization failing Andrew Reay
2 siblings, 1 reply; 6+ messages in thread
From: Antti Palosaari @ 2009-03-12 22:02 UTC (permalink / raw)
To: linux-media; +Cc: linux-dvb
Rolf Schumacher wrote:
> File not found: /lib/modules/2.6.28-7.slh.3-sidux-686/build/.config at
> ./scripts/make_kconfig.pl line 32, <IN> line 4.
kernel-devel, kernel-headers, linux-devel or linux-headers package is
missing. Package name varies from distribution to distribution...
--
http://palosaari.fi/
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [linux-dvb] getting started
2009-03-12 21:46 [linux-dvb] getting started Rolf Schumacher
2009-03-12 22:02 ` Antti Palosaari
@ 2009-03-12 22:04 ` Thomas Kaiser
2009-03-14 5:14 ` Compro T750F - frontend initialization failing Andrew Reay
2 siblings, 0 replies; 6+ messages in thread
From: Thomas Kaiser @ 2009-03-12 22:04 UTC (permalink / raw)
To: linux-media; +Cc: mailinglist
Rolf Schumacher wrote:
> I once had my TechnoTrend DVB-C driver working with linux, looking tv.
> However, completely forgot how I managed that.
>
> I think I was following the wiki
>
> How to Obtain, Build and Install V4L-DVB Device Driver
>
> I checked out the v4l-dvb sources using Mercurial.
> However, a make failed immediately:
>
> ------------
> make -C /home/rsc/src/v4l-dvb/v4l
> make[1]: Entering directory `/home/rsc/src/v4l-dvb/v4l'
> Updating/Creating .config
> Preparing to compile for kernel version 2.6.28
> File not found: /lib/modules/2.6.28-7.slh.3-sidux-686/build/.config at
> ./scripts/make_kconfig.pl line 32, <IN> line 4.
> make[1]: *** Keine Regel vorhanden, um das Target ».myconfig«,
> benötigt von »config-compat.h«, zu erstellen. Schluss.
> make[1]: Leaving directory `/home/rsc/src/v4l-dvb/v4l'
> make: *** [all] Fehler 2
> -----------
>
> Am I on the right track?
> If so, what is missing?
Kernel-headers and/or source installed?
Thomas
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [linux-dvb] getting started
2009-03-12 22:02 ` Antti Palosaari
@ 2009-03-12 22:47 ` Rolf Schumacher
0 siblings, 0 replies; 6+ messages in thread
From: Rolf Schumacher @ 2009-03-12 22:47 UTC (permalink / raw)
To: linux-media
thank you, Antti, Thomas
kernel-headers are installed.
Why does make try to read the wrong file?
My kernel is named 2.6.28-7.slh.4-sidux-686, not 2.6.28-7.slh.3-sidux-686
---------
rsc@rolf9:~/src/v4l-dvb$ make
make -C /home/rsc/src/v4l-dvb/v4l
make[1]: Entering directory `/home/rsc/src/v4l-dvb/v4l'
Updating/Creating .config
Preparing to compile for kernel version 2.6.28
File not found: /lib/modules/2.6.28-7.slh.3-sidux-686/build/.config at
./scripts/make_kconfig.pl line 32, <IN> line 4.
make[1]: *** Keine Regel vorhanden, um das Target ?.myconfig?,
beno"tigt von ?config-compat.h?, zu erstellen. Schluss.
make[1]: Leaving directory `/home/rsc/src/v4l-dvb/v4l'
make: *** [all] Fehler 2
rsc@rolf9:~/src/v4l-dvb$
rsc@rolf9:~/src/v4l-dvb$ ls -la
/lib/modules/2.6.28-7.slh.3-sidux-686/build/.config
ls: Zugriff auf /lib/modules/2.6.28-7.slh.3-sidux-686/build/.config
nicht mo"glich: Datei oder Verzeichnis nicht gefunden
rsc@rolf9:~/src/v4l-dvb$ ls -la
/lib/modules/2.6.28-7.slh.4-sidux-686/build/.config
-rw-r--r-- 1 root root 95158 12. Ma"r 00:30
/lib/modules/2.6.28-7.slh.4-sidux-686/build/.config
rsc@rolf9:~/src/v4l-dvb$ hg update
0 files updated, 0 files merged, 0 files removed, 0 files unresolved
rsc@rolf9:~/src/v4l-dvb$
------------
Antti Palosaari wrote:
> Rolf Schumacher wrote:
>
>> File not found: /lib/modules/2.6.28-7.slh.3-sidux-686/build/.config at
>> ./scripts/make_kconfig.pl line 32, <IN> line 4.
>>
>
> kernel-devel, kernel-headers, linux-devel or linux-headers package is
> missing. Package name varies from distribution to distribution...
>
>
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Compro T750F - frontend initialization failing
2009-03-12 21:46 [linux-dvb] getting started Rolf Schumacher
2009-03-12 22:02 ` Antti Palosaari
2009-03-12 22:04 ` Thomas Kaiser
@ 2009-03-14 5:14 ` Andrew Reay
2 siblings, 0 replies; 6+ messages in thread
From: Andrew Reay @ 2009-03-14 5:14 UTC (permalink / raw)
To: linux-media
Hi Everyone,
I'm having trouble with getting the Compro Video T750F to work under
Ubuntu 8.10. I had the Compro T300 working great but this card is still
eluding me.
Any suggestions on how to proceed from here?
The dmesg is posted below.
Thanks,
Andrew
[ 13.317113] saa7130/34: v4l2 driver version 0.2.14 loaded
[ 13.317703] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
[ 13.317709] saa7134 0000:04:08.0: PCI INT A -> Link[APC1] -> GSI 16
(level, low) -> IRQ 16
[ 13.317716] saa7133[0]: found at 0000:04:08.0, rev: 209, irq: 16,
latency: 32, mmio: 0xfdbfe000
[ 13.317723] saa7133[0]: subsystem: 185b:c900, board: Compro VideoMate
T750 [card=139,autodetected]
[ 13.317734] saa7133[0]: board init: gpio is 84bf00
[ 13.317746] saa7133[0]: Oops: IR config error [card=139]
[ 13.476035] saa7133[0]: i2c eeprom 00: 5b 18 00 c9 54 20 1c 00 43 43 a9
1c 55 d2 b2 92
[ 13.476046] saa7133[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff ff ff ff ff
ff ff ff ff ff
[ 13.476055] saa7133[0]: i2c eeprom 20: 01 40 01 02 02 01 03 01 08 ff 00
87 ff ff ff ff
[ 13.476064] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476072] saa7133[0]: i2c eeprom 40: ff d7 00 c4 86 1e 05 ff 02 c2 ff
01 c6 ff 05 ff
[ 13.476081] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff cb
[ 13.476089] saa7133[0]: i2c eeprom 60: 35 ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476098] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476106] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476115] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476123] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476132] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476140] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476149] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476157] saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476166] saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.508082] tuner 2-0062: chip found @ 0xc4 (saa7133[0])
[ 13.548912] xc2028 2-0062: creating new instance
[ 13.548916] xc2028 2-0062: type set to XCeive xc2028/xc3028 tuner
[ 13.548926] firmware: requesting xc3028-v27.fw
[ 13.999716] input: ImPS/2 Generic Wheel Mouse
as /devices/platform/i8042/serio1/input/input5
[ 14.055433] xc2028 2-0062: Loading 80 firmware images from
xc3028-v27.fw, type: xc2028 firmware, ver 2.7
[ 14.055534] xc2028 2-0062: Loading firmware for type=BASE F8MHZ MTS
(7), id 0000000000000000.
[ 14.055940] xc2028 2-0062: i2c output error: rc = -5 (should be 64)
[ 14.055943] xc2028 2-0062: -5 returned from send
[ 14.055947] xc2028 2-0062: Error -22 while loading base firmware
[ 14.108032] xc2028 2-0062: Loading firmware for type=BASE F8MHZ MTS
(7), id 0000000000000000.
[ 14.108570] xc2028 2-0062: i2c output error: rc = -5 (should be 64)
[ 14.108573] xc2028 2-0062: -5 returned from send
[ 14.108576] xc2028 2-0062: Error -22 while loading base firmware
[ 14.108589] xc2028 2-0062: Loading firmware for type=BASE F8MHZ MTS
(7), id 0000000000000000.
[ 14.109126] xc2028 2-0062: i2c output error: rc = -5 (should be 64)
[ 14.109128] xc2028 2-0062: -5 returned from send
[ 14.109131] xc2028 2-0062: Error -22 while loading base firmware
[ 14.165021] xc2028 2-0062: Loading firmware for type=BASE F8MHZ MTS
(7), id 0000000000000000.
[ 14.165555] xc2028 2-0062: i2c output error: rc = -5 (should be 64)
[ 14.165557] xc2028 2-0062: -5 returned from send
[ 14.165560] xc2028 2-0062: Error -22 while loading base firmware
[ 14.166394] xc2028 2-0062: Error on line 1124: -5
[ 14.173289] saa7133[0]: registered device video0 [v4l2]
[ 14.173451] saa7133[0]: registered device vbi0
[ 14.173507] saa7133[0]: registered device radio0
[ 14.174059] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
[ 14.174064] HDA Intel 0000:00:10.1: PCI INT B -> Link[AAZA] -> GSI 23
(level, low) -> IRQ 23
[ 14.174089] HDA Intel 0000:00:10.1: setting latency timer to 64
[ 14.196322] saa7134 ALSA driver for DMA sound loaded
[ 14.196353] saa7133[0]/alsa: saa7133[0] at 0xfdbfe000 irq 16 registered
as card -2
[ 14.337099] dvb_init() allocating 1 frontend
[ 14.337105] saa7133[0]/dvb: Huh? unknown DVB card?
[ 14.337108] saa7133[0]/dvb: frontend initialization failed
^ permalink raw reply [flat|nested] 6+ messages in thread
* [linux-dvb] getting started
@ 2009-03-12 22:32 Rolf Schumacher
0 siblings, 0 replies; 6+ messages in thread
From: Rolf Schumacher @ 2009-03-12 22:32 UTC (permalink / raw)
To: linux-media
I once had my TechnoTrend DVB-C driver working with linux, looking tv.
However, completely forgot how I managed that.
I think I was following the wiki
How to Obtain, Build and Install V4L-DVB Device Driver
I checked out the v4l-dvb sources using Mercurial.
However, a make failed immediately:
------------
make -C /home/rsc/src/v4l-dvb/v4l
make[1]: Entering directory `/home/rsc/src/v4l-dvb/v4l'
Updating/Creating .config
Preparing to compile for kernel version 2.6.28
File not found: /lib/modules/2.6.28-7.slh.3-sidux-686/build/.config at
./scripts/make_kconfig.pl line 32, <IN> line 4.
make[1]: *** Keine Regel vorhanden, um das Target ».myconfig«,
benötigt von »config-compat.h«, zu erstellen. Schluss.
make[1]: Leaving directory `/home/rsc/src/v4l-dvb/v4l'
make: *** [all] Fehler 2
-----------
Am I on the right track?
If so, what is missing?
ngong
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead linux-media@vger.kernel.org
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2009-03-14 5:14 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2009-03-12 21:46 [linux-dvb] getting started Rolf Schumacher
2009-03-12 22:02 ` Antti Palosaari
2009-03-12 22:47 ` Rolf Schumacher
2009-03-12 22:04 ` Thomas Kaiser
2009-03-14 5:14 ` Compro T750F - frontend initialization failing Andrew Reay
2009-03-12 22:32 [linux-dvb] getting started Rolf Schumacher
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.