From: john knops <jknops@australiaonline.net.au>
To: video4linux-list@redhat.com
Subject: Re: No scan with DViCo FusionHDTV DVB-T Dual Express
Date: Sat, 04 Apr 2009 00:22:42 +1100 [thread overview]
Message-ID: <49D60DA2.5040904@australiaonline.net.au> (raw)
In-Reply-To: <49D2FE07.5060906@australiaonline.net.au>
john knops wrote:
> Steven Toth wrote:
>> Hi John,
>>
>> john knops wrote:
>>> I'm using the DViCo card with Ubuntu 8.10amd64. I've followed the
>>> various instructions for installing drivers and firmware viz:-
>>> loaded the drivers(v4l-dvb-b44a3aed3d1.tar.gz) as suggested on
>>> www.linuxtv.org/wiki/index.php/DViCo_FusionHDTV_DVB-T_Dual_Express
>>> <http://www.linuxtv.org/wiki/index.php/DViCo_FusionHDTV_DVB-T_Dual_Express>
>>> from linuxtv.org/hg/~stoth/v4l-dvb. I also had to load
>>> gspca_m5602.ko in
>>> /lib/modules/2.6.27-11-generic/kernel/drivers/media/video/gspca.
>>
>>
>> The wiki url points to a page that doesn't exist.
>> You can get to this page via the wiki Main Page -> DVB-T Devices ->
>> DVB-T PCIe cards - Experimental Support.
>>
>>>
>>> The card wasn't auto-loaded until I added "options cx23885 card=11"
>>> to /etc/modprobe.d/options.
>>> I obtained xc3028-v27.fw.tar.bz2 via ubuntuforums.org then copied
>>> the untarred file xc3028-v27.fw to /lib/firmware.
>>
>> It's probably a new rev of the card with a new subid, which is why
>> you have to force load it.
>>
>> What does lspci -vn look like? (Show the section specific to the
>> cx23885).
>> Results of lspci -vn:-
> 01:00.0 Multimedia video controller [0400]: Conexant Systems, Inc.
> CX23885 PCI Video and Audio Decoder [14f1:8852] (rev 02)
> Subsystem: DViCO Corporation Device [18ac:db78]
> Flags: bus master, fast devsel, latency 0, IRQ 28
> Memory at f7e00000 (64-bit, non-prefetchable) [size=2M]
> Capabilities: [40] Express Endpoint, MSI 00
> Capabilities: [80] Power Management version 2
> Capabilities: [90] Vital Product Data <?>
> Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+
> Queue=0/0 Enable-
> Capabilities: [100] Advanced Error Reporting <?>
> Capabilities: [200] Virtual Channel <?>
> Kernel driver in use: cx23885
> Kernel modules: cx23885
>
>>
>>> [34889.915511] xc2028 0-0061: Loading SCODE for type=DTV6 QAM DTV7
>>> DTV78 DTV8 ZARLINK456 SCODE HAS_IF_4760 (620003e0), id
>>> 0000000000000000.
>>> [34889.949353] xc2028 0-0061: Incorrect readback of firmware version.
>>>
>>> Any ideas why I'm getting " Incorrect readback of firmware version"
>>> What have I missed/done wrong?
>>
>> ... and it may not have a xc3028 onboard, or may have the low power
>> version which is why the firmware fails to load. A few other things
>> come to mind but given that the vendor has switch subid details, it's
>> probably best to cross reference with the wiki to ensure it still has
>> the same parts.
>>
>> Assuming the wiki entry truly doesn't exist, maybe you could create
>> it with the newer rev details, maybe with some pictures and component
>> details?
>>
>> - Steve
>> I've e-mailed DViCo asking if there have been any recent changes to
>> the board. I'll get photos of the board later tonight.
> John..
More from John.
Although the card described on the wiki and the card that I own both
have the same name and have Fusion DVB-T Dual Express Rev:1.1 printed on
the underside, they are not identical eg:-
Wiki Card 2x Xceive 3008ACQ Mine 2x Xceive3028ACQ
Wiki Card 2x WJCE 6353 Mine 2x WJCE 6353
Wiki Conexant Cx23885 -13Z Mine Conexant Cx23885 -13Z
Wiki Card 28.636360 Kony 0703 Mine 28.636360 Kony 0741
Wiki Card 4.000000Kony 0703 Mine 4.000000Kony 0741
Wiki Card 0716Y 20.480 Mine 0720Y 20.480
I presume that this explains the problems that I am having and that I
will just have to wait until if/when this particular version of the
card is supported.
>
> video4linux-list mailing list
> Unsubscribe
> mailto:video4linux-list-request@redhat.com?subject=unsubscribe
> https://www.redhat.com/mailman/listinfo/video4linux-list
>
> ______________________________________________________________________
> This mail has been virus scanned and spam scanned by Australia On Line
> see http://www.australiaonline.net.au/spamscanning
>
> Report this email as spam...
> http://reportspam.australiaonline.net.au/servlet/mail/jknops/1238564413.18072_0.mailscanner2.ozonline.com.au/reportspam
>
>
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
next prev parent reply other threads:[~2009-04-03 13:40 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-03-31 12:22 No scan with DViCo FusionHDTV DVB-T Dual Express john knops
2009-03-31 14:24 ` Steven Toth
2009-03-31 14:32 ` Devin Heitmueller
2009-04-01 5:39 ` john knops
2009-04-03 13:22 ` john knops [this message]
2009-04-06 14:01 ` Steven Toth
2009-04-06 14:16 ` Devin Heitmueller
2009-04-07 13:08 ` john knops
2009-04-07 14:03 ` Devin Heitmueller
2009-04-09 22:23 ` john knops
2009-04-10 22:26 ` Devin Heitmueller
2009-04-11 12:37 ` Steven Toth
2009-04-11 12:39 ` Devin Heitmueller
2009-04-07 5:39 Christopher Pascoe
2009-04-22 16:58 ` Devin Heitmueller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=49D60DA2.5040904@australiaonline.net.au \
--to=jknops@australiaonline.net.au \
--cc=video4linux-list@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.