* Nvidia ION (MCP79) eSata fails for external cabinet Thecus N2050 (SIL5744)
@ 2009-10-07 15:23 Örjan Nordlund
2009-11-09 8:10 ` Tejun Heo
0 siblings, 1 reply; 4+ messages in thread
From: Örjan Nordlund @ 2009-10-07 15:23 UTC (permalink / raw)
To: linux-ide
Hi !
I am having an issue using eSata to connect my Thecus N2050 storage
cabinet to my new homeserver running Ubuntu Server 9.04.
dmesg shows "failed to IDENTIFY (I/O error, err_mask=0x100)"
I have read forums and mailing lists to understand solutions to
similar problems and the following steps have been taken:
Upgraded to Vanilla kernel 2.6.31
Changed BIOS settings from SATA->AHCI and then back again
Tried boot with pci=nomsi
Changed cables (i have three cables now and no one works)
Checked that no jumpers can be changed on disks or mainboard
Checked that the disks can be read through USB interface and from
other computers (works on Linux, OS X and Win XP)
Checked disks through eSata on Win XP box
Upgraded BIOS to latest release (August 2009)
I have looked in all forums and LKML archives for a solution but can
not really find anyone that has a similar problem.
I am suspecting the quirks are in the Thecus N2050. I have had some
problems with this device in linux before when i was using USB.
Thanks to Alan Stern a patch (as1154) was introduced in October 2008
to help get the device recognized properly by scsi when probing it.
My Nvidia ION board has a MCP79 controller on-board (should be OK
from 2.6.24) and the Thecus has a Silicon Image controller (i opened
the box and read on the chip) with markings:
SIL5744CNU
WE8799.00-19
0710
AG01CX2
I do not know what to do next and i appreciate any and all help i can
get that could point me in the right direction.
Kind regards,
Örjan Nordlund
orjan@laxfiske.se
Attached are dmesg (hotplug of device), /proc/interrupts, lspci,
lspci -vv, dmesg (from boot)
dmesg (extract from hotplug of device):
[ 753.849929] ata3: exception Emask 0x10 SAct 0x0 SErr 0x1810000
action 0xe frozen
[ 753.849970] ata3: irq_stat 0x00400000, PHY RDY changed
[ 753.849994] ata3: SError: { PHYRdyChg LinkSeq TrStaTrns }
[ 753.850024] ata3: hard resetting link
[ 754.598415] ata3: SATA link down (SStatus 10 SControl 300)
[ 754.598430] ata3: EH complete
[ 758.663954] ata3: exception Emask 0x10 SAct 0x0 SErr 0x4140000
action 0xe frozen
[ 758.663993] ata3: irq_stat 0x00000040, connection status changed
[ 758.664018] ata3: SError: { CommWake Dispar DevExch }
[ 758.664046] ata3: hard resetting link
[ 759.588208] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 759.588245] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
[ 764.587996] ata3: hard resetting link
[ 765.117974] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 765.118016] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
[ 765.118023] ata3: limiting SATA link speed to 1.5 Gbps
[ 770.117755] ata3: hard resetting link
[ 770.647737] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 770.647783] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
[ 775.647507] ata3: hard resetting link
[ 776.177483] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 776.177507] ata3: exception Emask 0x10 SAct 0x0 SErr 0x0 action
0x1 t4
[ 776.177536] ata3: irq_stat 0x08000000, interface fatal error
[ 776.177564] ata3: EH complete
cat /proc/interrupts:
CPU0
0: 31 XT-PIC-XT timer
1: 4 XT-PIC-XT i8042
2: 0 XT-PIC-XT cascade
7: 1 XT-PIC-XT
8: 0 XT-PIC-XT rtc0
9: 0 XT-PIC-XT ehci_hcd:usb2
10: 2449 XT-PIC-XT ehci_hcd:usb1, eth0
11: 0 XT-PIC-XT ohci_hcd:usb4
12: 6 XT-PIC-XT i8042
15: 149 XT-PIC-XT ohci_hcd:usb3, HDA Intel
29: 4132 PCI-MSI-edge ahci
NMI: 0 Non-maskable interrupts
LOC: 84954 Local timer interrupts
SPU: 0 Spurious interrupts
CNT: 0 Performance counter interrupts
PND: 0 Performance pending work
RES: 0 Rescheduling interrupts
CAL: 0 Function call interrupts
TLB: 0 TLB shootdowns
ERR: 1
MIS: 0
lspci:
00:00.0 Host bridge: nVidia Corporation MCP79 Host Bridge (rev b1)
00:00.1 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
00:03.0 ISA bridge: nVidia Corporation MCP79 LPC Bridge (rev b2)
00:03.1 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
00:03.2 SMBus: nVidia Corporation MCP79 SMBus (rev b1)
00:03.3 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
00:03.5 Co-processor: nVidia Corporation MCP79 Co-processor (rev b1)
00:04.0 USB Controller: nVidia Corporation MCP79 OHCI USB 1.1
Controller (rev b1)
00:04.1 USB Controller: nVidia Corporation MCP79 EHCI USB 2.0
Controller (rev b1)
00:06.0 USB Controller: nVidia Corporation MCP79 OHCI USB 1.1
Controller (rev b1)
00:06.1 USB Controller: nVidia Corporation MCP79 EHCI USB 2.0
Controller (rev b1)
00:08.0 Audio device: nVidia Corporation MCP79 High Definition Audio
(rev b1)
00:09.0 PCI bridge: nVidia Corporation MCP79 PCI Bridge (rev b1)
00:0a.0 Ethernet controller: nVidia Corporation MCP79 Ethernet (rev b1)
00:0b.0 IDE interface: nVidia Corporation MCP79 SATA Controller (rev b1)
00:0c.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
00:10.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
00:15.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
00:16.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
00:17.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
00:18.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
03:00.0 VGA compatible controller: nVidia Corporation Device 087d
(rev b1)
lspci -vv:
00:00.0 Host bridge: nVidia Corporation MCP79 Host Bridge (rev b1)
Subsystem: nVidia Corporation Device cb79
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.1 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
Subsystem: nVidia Corporation Device cb79
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:03.0 ISA bridge: nVidia Corporation MCP79 LPC Bridge (rev b2)
Subsystem: ZOTAC International (MCO) Ltd. Device a108
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: I/O ports at 4f00 [size=256]
00:03.1 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
Subsystem: ZOTAC International (MCO) Ltd. Device a108
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:03.2 SMBus: nVidia Corporation MCP79 SMBus (rev b1)
Subsystem: ZOTAC International (MCO) Ltd. Device a108
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 4900 [size=64]
Region 4: I/O ports at 4d00 [size=64]
Region 5: I/O ports at 4e00 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME
(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00:03.3 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
Subsystem: nVidia Corporation Device cb79
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:03.5 Co-processor: nVidia Corporation MCP79 Co-processor (rev b1)
Subsystem: ZOTAC International (MCO) Ltd. Device a108
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 9
Region 0: Memory at fae80000 (32-bit, non-prefetchable)
[size=512K]
00:04.0 USB Controller: nVidia Corporation MCP79 OHCI USB 1.1
Controller (rev b1) (prog-if 10)
Subsystem: ZOTAC International (MCO) Ltd. Device a108
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 15
Region 0: Memory at fae7f000 (32-bit, non-prefetchable)
[size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
00:04.1 USB Controller: nVidia Corporation MCP79 EHCI USB 2.0
Controller (rev b1) (prog-if 20)
Subsystem: ZOTAC International (MCO) Ltd. Device a108
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 10
Region 0: Memory at fae7ec00 (32-bit, non-prefetchable)
[size=256]
Capabilities: [44] Debug port: BAR=1 offset=00a0
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ehci_hcd
00:06.0 USB Controller: nVidia Corporation MCP79 OHCI USB 1.1
Controller (rev b1) (prog-if 10)
Subsystem: ZOTAC International (MCO) Ltd. Device a108
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fae7d000 (32-bit, non-prefetchable)
[size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
00:06.1 USB Controller: nVidia Corporation MCP79 EHCI USB 2.0
Controller (rev b1) (prog-if 20)
Subsystem: ZOTAC International (MCO) Ltd. Device a108
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 9
Region 0: Memory at fae7e800 (32-bit, non-prefetchable)
[size=256]
Capabilities: [44] Debug port: BAR=1 offset=00a0
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ehci_hcd
00:08.0 Audio device: nVidia Corporation MCP79 High Definition Audio
(rev b1)
Subsystem: PC Partner Limited Device 437b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 15
Region 0: Memory at fae78000 (32-bit, non-prefetchable)
[size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME
(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:09.0 PCI bridge: nVidia Corporation MCP79 PCI Bridge (rev b1)
(prog-if 01)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Capabilities: [b8] Subsystem: ZOTAC International (MCO) Ltd.
Device a108
00:0a.0 Ethernet controller: nVidia Corporation MCP79 Ethernet (rev b1)
Subsystem: ZOTAC International (MCO) Ltd. Device a108
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fae7c000 (32-bit, non-prefetchable)
[size=4K]
Region 1: I/O ports at d080 [size=8]
Region 2: Memory at fae7e400 (32-bit, non-prefetchable)
[size=256]
Region 3: Memory at fae7e000 (32-bit, non-prefetchable)
[size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
Kernel driver in use: forcedeth
Kernel modules: forcedeth
00:0b.0 IDE interface: nVidia Corporation MCP79 SATA Controller (rev
b1) (prog-if 85 [Master SecO PriO])
Subsystem: ZOTAC International (MCO) Ltd. Device a108
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 29
Region 0: I/O ports at d000 [size=8]
Region 1: I/O ports at cc00 [size=4]
Region 2: I/O ports at c880 [size=8]
Region 3: I/O ports at c800 [size=4]
Region 4: I/O ports at c480 [size=16]
Region 5: Memory at fae76000 (32-bit, non-prefetchable)
[size=8K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME
(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] SATA HBA <?>
Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit
+ Queue=0/3 Enable+
Address: 00000000fee0100c Data: 4171
Kernel driver in use: ahci
00:0c.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: ZOTAC International (MCO) Ltd.
Device a108
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit
+ Queue=0/1 Enable+
Address: 00000000fee0100c Data: 4149
Capabilities: [80] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency
L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal-
Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s
L1, Latency L0 <512ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled-
Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train-
SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
HotPlug- Surpise-
Slot # 0, PowerLimit 0.000000; Interlock-
NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
CmdCplt- HPIrq+ LinkChg+
Control: AttnInd Off, PwrInd On, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:10.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: faf00000-fbffffff
Prefetchable memory behind bridge:
00000000e0000000-00000000f9ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: ZOTAC International (MCO) Ltd.
Device a108
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit
+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Kernel modules: shpchp
00:15.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: ZOTAC International (MCO) Ltd.
Device a108
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit
+ Queue=0/1 Enable+
Address: 00000000fee0100c Data: 4151
Capabilities: [80] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency
L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal-
Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s
L1, Latency L0 <512ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled-
Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train-
SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
HotPlug- Surpise-
Slot # 0, PowerLimit 0.000000; Interlock-
NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
CmdCplt- HPIrq+ LinkChg+
Control: AttnInd Off, PwrInd On, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:16.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: ZOTAC International (MCO) Ltd.
Device a108
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit
+ Queue=0/1 Enable+
Address: 00000000fee0100c Data: 4159
Capabilities: [80] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency
L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal-
Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s
L1, Latency L0 <512ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled-
Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
HotPlug- Surpise-
Slot # 0, PowerLimit 0.000000; Interlock-
NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
CmdCplt- HPIrq+ LinkChg+
Control: AttnInd Off, PwrInd On, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:17.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: ZOTAC International (MCO) Ltd.
Device a108
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit
+ Queue=0/1 Enable+
Address: 00000000fee0100c Data: 4161
Capabilities: [80] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency
L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal-
Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s
L1, Latency L0 <512ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled-
Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
HotPlug- Surpise-
Slot # 0, PowerLimit 0.000000; Interlock-
NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
CmdCplt- HPIrq+ LinkChg+
Control: AttnInd Off, PwrInd On, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:18.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: ZOTAC International (MCO) Ltd.
Device a108
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit
+ Queue=0/1 Enable+
Address: 00000000fee0100c Data: 4169
Capabilities: [80] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency
L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal-
Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #6, Speed 2.5GT/s, Width x1, ASPM L0s
L1, Latency L0 <512ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled-
Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
HotPlug- Surpise-
Slot # 0, PowerLimit 0.000000; Interlock-
NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
CmdCplt- HPIrq+ LinkChg+
Control: AttnInd Off, PwrInd On, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
03:00.0 VGA compatible controller: nVidia Corporation Device 087d
(rev b1)
Subsystem: ZOTAC International (MCO) Ltd. Device a108
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fb000000 (32-bit, non-prefetchable)
[size=16M]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at f8000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at ec00 [size=128]
Expansion ROM at fafe0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME
(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Message Signalled Interrupts: Mask- 64bit
+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Kernel modules: nvidiafb
dmesg (boot):
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.31-ion (root@server.nordlund.se)
(gcc version 4.3.3 (Ubuntu 4.3.3-5ubuntu4) ) #1 SMP Sun Sep 13
14:14:48 CEST 2009
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000
(reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000
(reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000006ffa0000 (usable)
[ 0.000000] BIOS-e820: 000000006ffa0000 - 000000006ffae000 (ACPI
data)
[ 0.000000] BIOS-e820: 000000006ffae000 - 000000006fff0000 (ACPI
NVS)
[ 0.000000] BIOS-e820: 000000006fff0000 - 0000000080000000
(reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000
(reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000
(reserved)
[ 0.000000] BIOS-e820: 00000000ff700000 - 0000000100000000
(reserved)
[ 0.000000] DMI present.
[ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working
around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000
(usable) ==> (reserved)
[ 0.000000] last_pfn = 0x6ffa0 max_arch_pfn = 0x1000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-DFFFF uncachable
[ 0.000000] E0000-EFFFF write-through
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask 080000000 write-back
[ 0.000000] 1 disabled
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved)
[ 0.000000] modified: 0000000000010000 - 000000000009fc00 (usable)
[ 0.000000] modified: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] modified: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 000000006ffa0000 (usable)
[ 0.000000] modified: 000000006ffa0000 - 000000006ffae000 (ACPI
data)
[ 0.000000] modified: 000000006ffae000 - 000000006fff0000 (ACPI NVS)
[ 0.000000] modified: 000000006fff0000 - 0000000080000000 (reserved)
[ 0.000000] modified: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] modified: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] modified: 00000000ff700000 - 0000000100000000 (reserved)
[ 0.000000] initial memory mapped : 0 - 00c00000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000379fe000
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] 0000000000 - 0000200000 page 4k
[ 0.000000] 0000200000 - 0037800000 page 2M
[ 0.000000] 0037800000 - 00379fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 379fe000 @ 10000-16000
[ 0.000000] RAMDISK: 351d3000 - 37fef032
[ 0.000000] Allocated new RAMDISK: 0089b000 - 036b7032
[ 0.000000] Move RAMDISK from 00000000351d3000 - 0000000037fef031
to 0089b000 - 036b7031
[ 0.000000] 901MB HIGHMEM available.
[ 0.000000] 889MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 379fe000
[ 0.000000] low ram: 0 - 379fe000
[ 0.000000] node 0 low ram: 00000000 - 379fe000
[ 0.000000] node 0 bootmap 00012000 - 00018f40
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 -
00379fe000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==>
[0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==>
[0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==>
[0000006000 - 0000007000]
[ 0.000000] #3 [0000100000 - 0000893fd8] TEXT DATA BSS ==>
[0000100000 - 0000893fd8]
[ 0.000000] #4 [000009fc00 - 0000100000] BIOS reserved ==>
[000009fc00 - 0000100000]
[ 0.000000] #5 [0000894000 - 000089a1bf] BRK ==>
[0000894000 - 000089a1bf]
[ 0.000000] #6 [0000010000 - 0000012000] PGTABLE ==>
[0000010000 - 0000012000]
[ 0.000000] #7 [000089b000 - 00036b7032] NEW RAMDISK ==>
[000089b000 - 00036b7032]
[ 0.000000] #8 [0000012000 - 0000019000] BOOTMAP ==>
[0000012000 - 0000019000]
[ 0.000000] found SMP MP-table at [c00ff780] ff780
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000379fe
[ 0.000000] HighMem 0x000379fe -> 0x0006ffa0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0006ffa0
[ 0.000000] On node 0 totalpages: 458543
[ 0.000000] free_area_init_node: node 0, pgdat c076c720,
node_mem_map c36b8200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1748 pages used for memmap
[ 0.000000] Normal zone: 221994 pages, LIFO batch:31
[ 0.000000] HighMem zone: 1804 pages used for memmap
[ 0.000000] HighMem zone: 229014 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] Intel MultiProcessor Specification v1.4
[ 0.000000] Virtual Wire compatibility mode.
[ 0.000000] MPTABLE: OEM ID: nVidia
[ 0.000000] MPTABLE: Product ID: MCP7A
[ 0.000000] MPTABLE: APIC at: 0xFEE00000
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] I/O APIC #1 Version 17 at 0xFEC00000.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Processors: 1
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 -
00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 -
00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 -
0000000000100000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap:
80000000:7ec00000)
[ 0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 15 pages at c44bf000, static data
38684 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping
on. Total pages: 454959
[ 0.000000] Kernel command line: root=/dev/mapper/server-root ro
acpi=off noapic quiet splash
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7,
524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6,
262144 bytes)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] allocated 9172800 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't
want memory cgroups
[ 0.000000] Initializing HighMem for node 0 (000379fe:0006ffa0)
[ 0.000000] Memory: 1754080k/1834624k available (4545k kernel
code, 79208k reserved, 2066k data, 464k init, 923272k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff1e000 - 0xfffff000 ( 900 kB)
[ 0.000000] pkmap : 0xffa00000 - 0xffc00000 (2048 kB)
[ 0.000000] vmalloc : 0xf81fe000 - 0xff9fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf79fe000 ( 889 MB)
[ 0.000000] .init : 0xc0775000 - 0xc07e9000 ( 464 kB)
[ 0.000000] .data : 0xc0570433 - 0xc0774ec8 (2066 kB)
[ 0.000000] .text : 0xc0100000 - 0xc0570433 (4545 kB)
[ 0.000000] Checking if this processor honours the WP bit even in
supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3,
MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:512
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1600.096 MHz processor.
[ 0.000018] spurious 8259A interrupt: IRQ7.
[ 0.001954] Console: colour VGA+ 80x25
[ 0.001960] console [tty0] enabled
[ 0.010012] Calibrating delay loop (skipped), value calculated
using timer frequency.. 3200.19 BogoMIPS (lpj=16000960)
[ 0.010052] Security Framework initialized
[ 0.010062] SELinux: Disabled at boot.
[ 0.010076] Mount-cache hash table entries: 512
[ 0.010299] Initializing cgroup subsys ns
[ 0.010307] Initializing cgroup subsys cpuacct
[ 0.010315] Initializing cgroup subsys memory
[ 0.010329] Initializing cgroup subsys freezer
[ 0.010353] CPU: L1 I cache: 32K, L1 D cache: 24K
[ 0.010358] CPU: L2 cache: 512K
[ 0.010363] CPU: Unsupported number of siblings 2
[ 0.010370] using mwait in idle threads.
[ 0.010381] Performance Counters: Atom events, Intel PMU driver.
[ 0.010391] ... version: 3
[ 0.010395] ... bit width: 40
[ 0.010399] ... generic counters: 2
[ 0.010403] ... value mask: 000000ffffffffff
[ 0.010407] ... max period: 000000007fffffff
[ 0.010411] ... fixed-purpose counters: 3
[ 0.010415] ... counter mask: 0000000700000003
[ 0.010423] Checking 'hlt' instruction... OK.
[ 0.050888] SMP alternatives: switching to UP code
[ 0.061524] Freeing SMP alternatives: 30k freed
[ 0.061640] CPU0: Intel(R) Atom(TM) CPU 230 @ 1.60GHz stepping 02
[ 0.180193] Brought up 1 CPUs
[ 0.180200] Total of 1 processors activated (3200.19 BogoMIPS).
[ 0.180219] CPU0 attaching NULL sched-domain.
[ 0.180600] Booting paravirtualized kernel on bare hardware
[ 0.181059] regulator: core version 0.5
[ 0.181127] Time: 13:54:18 Date: 10/07/09
[ 0.181217] NET: Registered protocol family 16
[ 0.181879] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=7
[ 0.181886] PCI: Using configuration type 1 for base access
[ 0.183772] bio: create slab <bio-0> at 0
[ 0.183910] ACPI: Interpreter disabled.
[ 0.184133] SCSI subsystem initialized
[ 0.184209] libata version 3.00 loaded.
[ 0.184358] usbcore: registered new interface driver usbfs
[ 0.184393] usbcore: registered new interface driver hub
[ 0.184450] usbcore: registered new device driver usb
[ 0.184672] PCI: Probing PCI hardware
[ 0.184678] PCI: Probing PCI hardware (bus 00)
[ 0.184958] pci 0000:00:03.0: reg 10 io port: [0x4f00-0x4fff]
[ 0.185085] pci 0000:00:03.2: reg 10 io port: [0x4900-0x493f]
[ 0.185106] pci 0000:00:03.2: reg 20 io port: [0x4d00-0x4d3f]
[ 0.185115] pci 0000:00:03.2: reg 24 io port: [0x4e00-0x4e3f]
[ 0.185145] pci 0000:00:03.2: PME# supported from D3hot D3cold
[ 0.185155] pci 0000:00:03.2: PME# disabled
[ 0.185305] pci 0000:00:03.5: reg 10 32bit mmio:
[0xfae80000-0xfaefffff]
[ 0.185413] pci 0000:00:04.0: reg 10 32bit mmio:
[0xfae7f000-0xfae7ffff]
[ 0.185454] pci 0000:00:04.0: supports D1 D2
[ 0.185458] pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.185465] pci 0000:00:04.0: PME# disabled
[ 0.185505] pci 0000:00:04.1: reg 10 32bit mmio:
[0xfae7ec00-0xfae7ecff]
[ 0.185552] pci 0000:00:04.1: supports D1 D2
[ 0.185557] pci 0000:00:04.1: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.185564] pci 0000:00:04.1: PME# disabled
[ 0.185608] pci 0000:00:06.0: reg 10 32bit mmio:
[0xfae7d000-0xfae7dfff]
[ 0.185649] pci 0000:00:06.0: supports D1 D2
[ 0.185654] pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.185661] pci 0000:00:06.0: PME# disabled
[ 0.185700] pci 0000:00:06.1: reg 10 32bit mmio:
[0xfae7e800-0xfae7e8ff]
[ 0.185747] pci 0000:00:06.1: supports D1 D2
[ 0.185752] pci 0000:00:06.1: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.185759] pci 0000:00:06.1: PME# disabled
[ 0.185803] pci 0000:00:08.0: reg 10 32bit mmio:
[0xfae78000-0xfae7bfff]
[ 0.185845] pci 0000:00:08.0: PME# supported from D3hot D3cold
[ 0.185851] pci 0000:00:08.0: PME# disabled
[ 0.185927] pci 0000:00:0a.0: reg 10 32bit mmio:
[0xfae7c000-0xfae7cfff]
[ 0.185937] pci 0000:00:0a.0: reg 14 io port: [0xd080-0xd087]
[ 0.185946] pci 0000:00:0a.0: reg 18 32bit mmio:
[0xfae7e400-0xfae7e4ff]
[ 0.185955] pci 0000:00:0a.0: reg 1c 32bit mmio:
[0xfae7e000-0xfae7e00f]
[ 0.185986] pci 0000:00:0a.0: supports D1 D2
[ 0.185991] pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.185999] pci 0000:00:0a.0: PME# disabled
[ 0.186040] pci 0000:00:0b.0: reg 10 io port: [0xd000-0xd007]
[ 0.186049] pci 0000:00:0b.0: reg 14 io port: [0xcc00-0xcc03]
[ 0.186058] pci 0000:00:0b.0: reg 18 io port: [0xc880-0xc887]
[ 0.186067] pci 0000:00:0b.0: reg 1c io port: [0xc800-0xc803]
[ 0.186076] pci 0000:00:0b.0: reg 20 io port: [0xc480-0xc48f]
[ 0.186085] pci 0000:00:0b.0: reg 24 32bit mmio:
[0xfae76000-0xfae77fff]
[ 0.186316] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.186327] pci 0000:00:0c.0: PME# disabled
[ 0.186416] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.186423] pci 0000:00:10.0: PME# disabled
[ 0.186635] pci 0000:00:15.0: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.186646] pci 0000:00:15.0: PME# disabled
[ 0.186879] pci 0000:00:16.0: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.186891] pci 0000:00:16.0: PME# disabled
[ 0.187129] pci 0000:00:17.0: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.187140] pci 0000:00:17.0: PME# disabled
[ 0.187375] pci 0000:00:18.0: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.187386] pci 0000:00:18.0: PME# disabled
[ 0.187481] pci 0000:00:09.0: transparent bridge
[ 0.187621] pci 0000:03:00.0: reg 10 32bit mmio:
[0xfb000000-0xfbffffff]
[ 0.187636] pci 0000:03:00.0: reg 14 64bit mmio:
[0xe0000000-0xefffffff]
[ 0.187650] pci 0000:03:00.0: reg 1c 64bit mmio:
[0xf8000000-0xf9ffffff]
[ 0.187661] pci 0000:03:00.0: reg 24 io port: [0xec00-0xec7f]
[ 0.187671] pci 0000:03:00.0: reg 30 32bit mmio:
[0xfafe0000-0xfaffffff]
[ 0.187739] pci 0000:00:10.0: bridge io port: [0xe000-0xefff]
[ 0.187746] pci 0000:00:10.0: bridge 32bit mmio:
[0xfaf00000-0xfbffffff]
[ 0.187755] pci 0000:00:10.0: bridge 64bit mmio pref:
[0xe0000000-0xf9ffffff]
[ 0.189350] pci 0000:00:03.1: default IRQ router [10de:0aa4]
[ 0.189737] Bluetooth: Core ver 2.15
[ 0.189814] NET: Registered protocol family 31
[ 0.189818] Bluetooth: HCI device and connection manager initialized
[ 0.189824] Bluetooth: HCI socket layer initialized
[ 0.189829] NET: Registered protocol family 8
[ 0.189833] NET: Registered protocol family 20
[ 0.189856] NetLabel: Initializing
[ 0.189860] NetLabel: domain hash size = 128
[ 0.189864] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.189889] NetLabel: unlabeled traffic allowed by default
[ 0.192626] pnp: PnP ACPI: disabled
[ 0.193089] pci 0000:00:09.0: PCI bridge, secondary bus 0000:01
[ 0.193096] pci 0000:00:09.0: IO window: disabled
[ 0.193103] pci 0000:00:09.0: MEM window: disabled
[ 0.193110] pci 0000:00:09.0: PREFETCH window: disabled
[ 0.193117] pci 0000:00:0c.0: PCI bridge, secondary bus 0000:02
[ 0.193121] pci 0000:00:0c.0: IO window: disabled
[ 0.193134] pci 0000:00:0c.0: MEM window: disabled
[ 0.193144] pci 0000:00:0c.0: PREFETCH window: disabled
[ 0.193156] pci 0000:00:10.0: PCI bridge, secondary bus 0000:03
[ 0.193162] pci 0000:00:10.0: IO window: 0xe000-0xefff
[ 0.193170] pci 0000:00:10.0: MEM window: 0xfaf00000-0xfbffffff
[ 0.193178] pci 0000:00:10.0: PREFETCH window:
0x000000e0000000-0x000000f9ffffff
[ 0.193187] pci 0000:00:15.0: PCI bridge, secondary bus 0000:04
[ 0.193191] pci 0000:00:15.0: IO window: disabled
[ 0.193204] pci 0000:00:15.0: MEM window: disabled
[ 0.193214] pci 0000:00:15.0: PREFETCH window: disabled
[ 0.193225] pci 0000:00:16.0: PCI bridge, secondary bus 0000:05
[ 0.193229] pci 0000:00:16.0: IO window: disabled
[ 0.193242] pci 0000:00:16.0: MEM window: disabled
[ 0.193253] pci 0000:00:16.0: PREFETCH window: disabled
[ 0.193263] pci 0000:00:17.0: PCI bridge, secondary bus 0000:06
[ 0.193268] pci 0000:00:17.0: IO window: disabled
[ 0.193281] pci 0000:00:17.0: MEM window: disabled
[ 0.193291] pci 0000:00:17.0: PREFETCH window: disabled
[ 0.193302] pci 0000:00:18.0: PCI bridge, secondary bus 0000:07
[ 0.193306] pci 0000:00:18.0: IO window: disabled
[ 0.193319] pci 0000:00:18.0: MEM window: disabled
[ 0.193330] pci 0000:00:18.0: PREFETCH window: disabled
[ 0.193349] pci 0000:00:09.0: setting latency timer to 64
[ 0.193380] pci 0000:00:0c.0: setting latency timer to 64
[ 0.193393] pci 0000:00:10.0: setting latency timer to 64
[ 0.193421] pci 0000:00:15.0: setting latency timer to 64
[ 0.193452] pci 0000:00:16.0: setting latency timer to 64
[ 0.193482] pci 0000:00:17.0: setting latency timer to 64
[ 0.193513] pci 0000:00:18.0: setting latency timer to 64
[ 0.193523] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.193530] pci_bus 0000:00: resource 1 mem:
[0x000000-0xffffffffffffffff]
[ 0.193536] pci_bus 0000:01: resource 3 io: [0x00-0xffff]
[ 0.193542] pci_bus 0000:01: resource 4 mem:
[0x000000-0xffffffffffffffff]
[ 0.193549] pci_bus 0000:03: resource 0 io: [0xe000-0xefff]
[ 0.193555] pci_bus 0000:03: resource 1 mem: [0xfaf00000-0xfbffffff]
[ 0.193561] pci_bus 0000:03: resource 2 pref mem
[0xe0000000-0xf9ffffff]
[ 0.193633] NET: Registered protocol family 2
[ 0.193837] IP route cache hash table entries: 32768 (order: 5,
131072 bytes)
[ 0.194496] TCP established hash table entries: 131072 (order: 8,
1048576 bytes)
[ 0.195347] TCP bind hash table entries: 65536 (order: 7, 524288
bytes)
[ 0.195769] TCP: Hash tables configured (established 131072 bind
65536)
[ 0.195776] TCP reno registered
[ 0.195970] NET: Registered protocol family 1
[ 0.196096] Trying to unpack rootfs image as initramfs...
[ 2.764149] Freeing initrd memory: 47216k freed
[ 2.805111] platform rtc_cmos: registered platform RTC device (no
PNP device found)
[ 2.805220] cpufreq-nforce2: No nForce2 chipset.
[ 2.805262] Scanning for low memory corruption every 60 seconds
[ 2.805471] audit: initializing netlink socket (disabled)
[ 2.805523] type=2000 audit(1254923660.799:1): initialized
[ 2.821820] highmem bounce pool size: 64 pages
[ 2.821832] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 2.824685] VFS: Disk quotas dquot_6.5.2
[ 2.824812] Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
[ 2.826048] fuse init (API version 7.12)
[ 2.826224] msgmni has been set to 1716
[ 2.826607] alg: No test for stdrng (krng)
[ 2.826636] io scheduler noop registered
[ 2.826642] io scheduler anticipatory registered
[ 2.826646] io scheduler deadline registered (default)
[ 2.826750] io scheduler cfq registered
[ 2.890260] pci 0000:03:00.0: Boot video device
[ 2.890646] pcieport-driver 0000:00:0c.0: irq 24 for MSI/MSI-X
[ 2.890672] pcieport-driver 0000:00:0c.0: setting latency timer to 64
[ 2.891095] pcieport-driver 0000:00:15.0: irq 25 for MSI/MSI-X
[ 2.891120] pcieport-driver 0000:00:15.0: setting latency timer to 64
[ 2.891531] pcieport-driver 0000:00:16.0: irq 26 for MSI/MSI-X
[ 2.891556] pcieport-driver 0000:00:16.0: setting latency timer to 64
[ 2.891965] pcieport-driver 0000:00:17.0: irq 27 for MSI/MSI-X
[ 2.891989] pcieport-driver 0000:00:17.0: setting latency timer to 64
[ 2.892389] pcieport-driver 0000:00:18.0: irq 28 for MSI/MSI-X
[ 2.892413] pcieport-driver 0000:00:18.0: setting latency timer to 64
[ 2.892620] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 2.892672] pciehp: PCI Express Hot Plug Controller Driver
version: 0.4
[ 2.892790] XENFS: not registering filesystem on non-xen platform
[ 2.895163] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 2.895279] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.897427] brd: module loaded
[ 2.898398] loop: module loaded
[ 2.898562] input: Macintosh mouse button emulation as /devices/
virtual/input/input0
[ 2.898719] ahci 0000:00:0b.0: version 3.0
[ 2.898739] ahci 0000:00:0b.0: guessed PCI INT A -> IRQ 5
[ 2.898865] ahci 0000:00:0b.0: irq 29 for MSI/MSI-X
[ 2.898978] ahci 0000:00:0b.0: AHCI 0001.0200 32 slots 6 ports 3
Gbps 0x3f impl IDE mode
[ 2.898986] ahci 0000:00:0b.0: flags: 64bit ncq sntf led pmp pio
slum part
[ 2.898994] ahci 0000:00:0b.0: setting latency timer to 64
[ 2.899942] scsi0 : ahci
[ 2.900164] scsi1 : ahci
[ 2.900276] scsi2 : ahci
[ 2.900390] scsi3 : ahci
[ 2.900500] scsi4 : ahci
[ 2.900617] scsi5 : ahci
[ 2.900700] ata1: SATA max UDMA/133 abar m8192@0xfae76000 port
0xfae76100 irq 29
[ 2.900708] ata2: SATA max UDMA/133 abar m8192@0xfae76000 port
0xfae76180 irq 29
[ 2.900714] ata3: SATA max UDMA/133 abar m8192@0xfae76000 port
0xfae76200 irq 29
[ 2.900721] ata4: SATA max UDMA/133 abar m8192@0xfae76000 port
0xfae76280 irq 29
[ 2.900727] ata5: SATA max UDMA/133 abar m8192@0xfae76000 port
0xfae76300 irq 29
[ 2.900734] ata6: SATA max UDMA/133 abar m8192@0xfae76000 port
0xfae76380 irq 29
[ 2.902205] Fixed MDIO Bus: probed
[ 2.902218] PPP generic driver version 2.4.2
[ 2.902423] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
Driver
[ 2.902476] ehci_hcd 0000:00:04.1: setting latency timer to 64
[ 2.902483] ehci_hcd 0000:00:04.1: EHCI Host Controller
[ 2.902590] ehci_hcd 0000:00:04.1: new USB bus registered,
assigned bus number 1
[ 2.902633] ehci_hcd 0000:00:04.1: debug port 1
[ 2.902642] ehci_hcd 0000:00:04.1: cache line size of 32 is not
supported
[ 2.902659] ehci_hcd 0000:00:04.1: irq 10, io mem 0xfae7ec00
[ 2.919875] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00
[ 2.920029] usb usb1: configuration #1 chosen from 1 choice
[ 2.920098] hub 1-0:1.0: USB hub found
[ 2.920116] hub 1-0:1.0: 6 ports detected
[ 2.920236] ehci_hcd 0000:00:06.1: setting latency timer to 64
[ 2.920243] ehci_hcd 0000:00:06.1: EHCI Host Controller
[ 2.920311] ehci_hcd 0000:00:06.1: new USB bus registered,
assigned bus number 2
[ 2.920351] ehci_hcd 0000:00:06.1: debug port 1
[ 2.920360] ehci_hcd 0000:00:06.1: cache line size of 32 is not
supported
[ 2.920377] ehci_hcd 0000:00:06.1: irq 9, io mem 0xfae7e800
[ 2.939866] ehci_hcd 0000:00:06.1: USB 2.0 started, EHCI 1.00
[ 2.939995] usb usb2: configuration #1 chosen from 1 choice
[ 2.940055] hub 2-0:1.0: USB hub found
[ 2.940070] hub 2-0:1.0: 6 ports detected
[ 2.940180] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.940231] ohci_hcd 0000:00:04.0: setting latency timer to 64
[ 2.940238] ohci_hcd 0000:00:04.0: OHCI Host Controller
[ 2.940309] ohci_hcd 0000:00:04.0: new USB bus registered,
assigned bus number 3
[ 2.940335] ohci_hcd 0000:00:04.0: irq 15, io mem 0xfae7f000
[ 3.001984] usb usb3: configuration #1 chosen from 1 choice
[ 3.002044] hub 3-0:1.0: USB hub found
[ 3.002061] hub 3-0:1.0: 6 ports detected
[ 3.002163] ohci_hcd 0000:00:06.0: setting latency timer to 64
[ 3.002170] ohci_hcd 0000:00:06.0: OHCI Host Controller
[ 3.002241] ohci_hcd 0000:00:06.0: new USB bus registered,
assigned bus number 4
[ 3.002266] ohci_hcd 0000:00:06.0: irq 11, io mem 0xfae7d000
[ 3.061990] usb usb4: configuration #1 chosen from 1 choice
[ 3.062048] hub 4-0:1.0: USB hub found
[ 3.062064] hub 4-0:1.0: 6 ports detected
[ 3.062165] uhci_hcd: USB Universal Host Controller Interface driver
[ 3.062316] usbcore: registered new interface driver libusual
[ 3.062384] usbcore: registered new interface driver usbserial
[ 3.062407] USB Serial support registered for generic
[ 3.062438] usbcore: registered new interface driver
usbserial_generic
[ 3.062443] usbserial: USB Serial Driver core
[ 3.062510] PNP: No PS/2 controller found. Probing ports directly.
[ 3.063960] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.063973] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 3.064090] mice: PS/2 mouse device common for all mice
[ 3.064267] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[ 3.064316] rtc0: alarms up to one day, 114 bytes nvram
[ 3.064536] device-mapper: uevent: version 1.0.3
[ 3.064784] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01)
initialised: dm-devel@redhat.com
[ 3.064882] device-mapper: multipath: version 1.1.0 loaded
[ 3.064889] device-mapper: multipath round-robin: version 1.0.0
loaded
[ 3.065152] cpuidle: using governor ladder
[ 3.065157] cpuidle: using governor menu
[ 3.066113] TCP cubic registered
[ 3.066456] NET: Registered protocol family 10
[ 3.067322] lo: Disabled Privacy Extensions
[ 3.067982] NET: Registered protocol family 17
[ 3.068027] Bluetooth: L2CAP ver 2.13
[ 3.068031] Bluetooth: L2CAP socket layer initialized
[ 3.068037] Bluetooth: SCO (Voice Link) ver 0.6
[ 3.068041] Bluetooth: SCO socket layer initialized
[ 3.068103] Bluetooth: RFCOMM TTY layer initialized
[ 3.068110] Bluetooth: RFCOMM socket layer initialized
[ 3.068114] Bluetooth: RFCOMM ver 1.11
[ 3.068173] Using IPI No-Shortcut mode
[ 3.068316] PM: Resume from disk failed.
[ 3.068361] registered taskstats version 1
[ 3.068575] Magic number: 13:817:937
[ 3.068683] rtc_cmos rtc_cmos: setting system clock to 2009-10-07
13:54:21 UTC (1254923661)
[ 3.068691] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 3.068695] EDD information not available.
[ 3.249863] ata2: SATA link down (SStatus 0 SControl 300)
[ 3.249899] ata5: SATA link down (SStatus 0 SControl 300)
[ 3.249926] ata4: SATA link down (SStatus 0 SControl 300)
[ 3.249963] ata6: SATA link down (SStatus 0 SControl 300)
[ 3.429843] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.429866] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.429902] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
[ 3.470145] ata1.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
[ 3.470152] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth
31/32)
[ 3.528485] ata1.00: configured for UDMA/133
[ 3.528678] scsi 0:0:0:0: Direct-Access ATA
ST3320620AS 3.AA PQ: 0 ANSI: 5
[ 3.528935] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.529024] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks:
(320 GB/298 GiB)
[ 3.529145] sd 0:0:0:0: [sda] Write Protect is off
[ 3.529152] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.529215] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 3.529533] sda: sda1 sda2 < sda5 >
[ 3.592918] sd 0:0:0:0: [sda] Attached SCSI disk
[ 8.959556] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 8.959596] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
[ 8.959603] ata3: limiting SATA link speed to 1.5 Gbps
[ 14.489267] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 14.489299] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
[ 20.018980] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 20.019000] ata3: exception Emask 0x10 SAct 0x0 SErr 0x0 action
0x1 t4
[ 20.019066] ata3: irq_stat 0x08000000, interface fatal error
[ 20.019186] Freeing unused kernel memory: 464k freed
[ 20.019572] Write protecting the kernel text: 4548k
[ 20.019672] Write protecting the kernel read-only data: 1676k
[ 20.363075] forcedeth: Reverse Engineered nForce ethernet driver.
Version 0.64.
[ 20.363104] forcedeth 0000:00:0a.0: setting latency timer to 64
[ 20.441292] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @
3, addr 00:01:2e:27:3c:19
[ 20.441302] forcedeth 0000:00:0a.0: highdma csum pwrctl gbit
lnktim msi desc-v3
[ 21.211257] PM: Starting manual resume from disk
[ 21.211267] PM: Resume from partition 252:1
[ 21.211271] PM: Checking hibernation image.
[ 21.211447] PM: Resume from disk failed.
[ 21.218989] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 21.218997] EXT3-fs: write access will be enabled during recovery.
[ 21.308267] kjournald starting. Commit interval 5 seconds
[ 21.308293] EXT3-fs: recovery complete.
[ 21.308707] EXT3-fs: mounted filesystem with writeback data mode.
[ 22.885578] udev: starting version 141
[ 23.273454] shpchp: Standard Hot Plug PCI Controller Driver
version: 0.4
[ 23.433134] input: PC Speaker as /devices/platform/pcspkr/input/
input1
[ 23.757633] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4d00
[ 23.757676] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x4e00
[ 24.868474] HDA Intel 0000:00:08.0: setting latency timer to 64
[ 26.298678] hda_codec: Unknown model for ALC662 rev1, trying auto-
probe from BIOS...
[ 26.858750] input: HDA Digital PCBeep as /devices/
pci0000:00/0000:00:08.0/input/input2
[ 27.857570] lp: driver loaded but no devices found
[ 28.054378] Adding 5275640k swap on /dev/mapper/server-swap_1.
Priority:-1 extents:1 across:5275640k
[ 28.605744] EXT3 FS on dm-0, internal journal
[ 34.057883] eth0: no IPv6 routers present
[ 39.504541] NET: Registered protocol family 5
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Nvidia ION (MCP79) eSata fails for external cabinet Thecus N2050 (SIL5744)
2009-10-07 15:23 Nvidia ION (MCP79) eSata fails for external cabinet Thecus N2050 (SIL5744) Örjan Nordlund
@ 2009-11-09 8:10 ` Tejun Heo
2009-11-12 12:51 ` Örjan Nordlund
0 siblings, 1 reply; 4+ messages in thread
From: Tejun Heo @ 2009-11-09 8:10 UTC (permalink / raw)
To: Örjan Nordlund; +Cc: linux-ide
Hello,
Örjan Nordlund wrote:
> I am having an issue using eSata to connect my Thecus N2050 storage
> cabinet to my new homeserver running Ubuntu Server 9.04.
> dmesg shows "failed to IDENTIFY (I/O error, err_mask=0x100)"
>
> I have read forums and mailing lists to understand solutions to similar
> problems and the following steps have been taken:
> Upgraded to Vanilla kernel 2.6.31
> Changed BIOS settings from SATA->AHCI and then back again
> Tried boot with pci=nomsi
> Changed cables (i have three cables now and no one works)
> Checked that no jumpers can be changed on disks or mainboard
> Checked that the disks can be read through USB interface and from other
> computers (works on Linux, OS X and Win XP)
> Checked disks through eSata on Win XP box
> Upgraded BIOS to latest release (August 2009)
>
> I have looked in all forums and LKML archives for a solution but can not
> really find anyone that has a similar problem.
>
> I am suspecting the quirks are in the Thecus N2050. I have had some
> problems with this device in linux before when i was using USB. Thanks
> to Alan Stern a patch (as1154) was introduced in October 2008 to help
> get the device recognized properly by scsi when probing it.
>
> My Nvidia ION board has a MCP79 controller on-board (should be OK from
> 2.6.24) and the Thecus has a Silicon Image controller (i opened the box
> and read on the chip) with markings:
> SIL5744CNU
SIL5744 should work fine. Hmmm...
> dmesg (extract from hotplug of device):
> [ 753.849929] ata3: exception Emask 0x10 SAct 0x0 SErr 0x1810000 action
> 0xe frozen
> [ 753.849970] ata3: irq_stat 0x00400000, PHY RDY changed
> [ 753.849994] ata3: SError: { PHYRdyChg LinkSeq TrStaTrns }
> [ 753.850024] ata3: hard resetting link
> [ 754.598415] ata3: SATA link down (SStatus 10 SControl 300)
> [ 754.598430] ata3: EH complete
> [ 758.663954] ata3: exception Emask 0x10 SAct 0x0 SErr 0x4140000 action
> 0xe frozen
> [ 758.663993] ata3: irq_stat 0x00000040, connection status changed
> [ 758.664018] ata3: SError: { CommWake Dispar DevExch }
> [ 758.664046] ata3: hard resetting link
> [ 759.588208] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 759.588245] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
Looks like the device is failing IDENTIFYs immediately. I don't think
this has anything to do with being _e_SATA. Can you try it with other
controllers?
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Nvidia ION (MCP79) eSata fails for external cabinet Thecus N2050 (SIL5744)
2009-11-09 8:10 ` Tejun Heo
@ 2009-11-12 12:51 ` Örjan Nordlund
2009-11-12 20:04 ` Tejun Heo
0 siblings, 1 reply; 4+ messages in thread
From: Örjan Nordlund @ 2009-11-12 12:51 UTC (permalink / raw)
To: Tejun Heo; +Cc: linux-ide
Will do. Have to wait until i am in the office again. I only have eSata on my ubuntu box @ home.
As previously stated this device has had some quirks before when i tried to use USB. The comments below are from Alan Stern who developed a patch for scsi_scan.c to make the device work when using the USB port on the Thecus N2050.
<snip>
This patch (as1154) fixes a problem in scsi_probe_lun(): The function
doesn't check whether the device has actually sent back any INQUIRY
data! The patch adds a test to see if the result buffer is still
empty after the command has been executed.
This enables the Thecus N2050 storage device to work. The firmware on
that device starts up strangely; it sends no data in response to the
initial INQUIRY, and it sends the INQUIRY information in response to
the followup REQUEST SENSE! But after that it works better, so
retrying the INQUIRY is enough to get it going.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
</snip>
Örjan Nordlund
orjan@laxfiske.se
+46 707 93 61 28
9 nov 2009 kl. 09.10 skrev Tejun Heo:
> Hello,
>
> Örjan Nordlund wrote:
>> I am having an issue using eSata to connect my Thecus N2050 storage
>> cabinet to my new homeserver running Ubuntu Server 9.04.
>> dmesg shows "failed to IDENTIFY (I/O error, err_mask=0x100)"
>>
>> I have read forums and mailing lists to understand solutions to similar
>> problems and the following steps have been taken:
>> Upgraded to Vanilla kernel 2.6.31
>> Changed BIOS settings from SATA->AHCI and then back again
>> Tried boot with pci=nomsi
>> Changed cables (i have three cables now and no one works)
>> Checked that no jumpers can be changed on disks or mainboard
>> Checked that the disks can be read through USB interface and from other
>> computers (works on Linux, OS X and Win XP)
>> Checked disks through eSata on Win XP box
>> Upgraded BIOS to latest release (August 2009)
>>
>> I have looked in all forums and LKML archives for a solution but can not
>> really find anyone that has a similar problem.
>>
>> I am suspecting the quirks are in the Thecus N2050. I have had some
>> problems with this device in linux before when i was using USB. Thanks
>> to Alan Stern a patch (as1154) was introduced in October 2008 to help
>> get the device recognized properly by scsi when probing it.
>>
>> My Nvidia ION board has a MCP79 controller on-board (should be OK from
>> 2.6.24) and the Thecus has a Silicon Image controller (i opened the box
>> and read on the chip) with markings:
>> SIL5744CNU
>
> SIL5744 should work fine. Hmmm...
>
>> dmesg (extract from hotplug of device):
>> [ 753.849929] ata3: exception Emask 0x10 SAct 0x0 SErr 0x1810000 action
>> 0xe frozen
>> [ 753.849970] ata3: irq_stat 0x00400000, PHY RDY changed
>> [ 753.849994] ata3: SError: { PHYRdyChg LinkSeq TrStaTrns }
>> [ 753.850024] ata3: hard resetting link
>> [ 754.598415] ata3: SATA link down (SStatus 10 SControl 300)
>> [ 754.598430] ata3: EH complete
>> [ 758.663954] ata3: exception Emask 0x10 SAct 0x0 SErr 0x4140000 action
>> 0xe frozen
>> [ 758.663993] ata3: irq_stat 0x00000040, connection status changed
>> [ 758.664018] ata3: SError: { CommWake Dispar DevExch }
>> [ 758.664046] ata3: hard resetting link
>> [ 759.588208] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> [ 759.588245] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
>
> Looks like the device is failing IDENTIFYs immediately. I don't think
> this has anything to do with being _e_SATA. Can you try it with other
> controllers?
>
> Thanks.
>
> --
> tejun
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Nvidia ION (MCP79) eSata fails for external cabinet Thecus N2050 (SIL5744)
2009-11-12 12:51 ` Örjan Nordlund
@ 2009-11-12 20:04 ` Tejun Heo
0 siblings, 0 replies; 4+ messages in thread
From: Tejun Heo @ 2009-11-12 20:04 UTC (permalink / raw)
To: Örjan Nordlund; +Cc: linux-ide
11/12/2009 09:51 PM, Örjan Nordlund wrote:
> Will do. Have to wait until i am in the office again. I only have
> eSata on my ubuntu box @ home. As previously stated this device has
> had some quirks before when i tried to use USB. The comments below
> are from Alan Stern who developed a patch for scsi_scan.c to make
> the device work when using the USB port on the Thecus N2050.
The two interfaces the device implement are pretty much independent.
USB presents itself as a SCSI device while the eSATA device will show
up as a SATA device. For some reason, recent 5744s seem to have
various firmware issues, so it wouldn't be too surprising if it has
similar bugs on ATA side too. Anyways, please let us know what you
find.
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2009-11-12 20:03 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2009-10-07 15:23 Nvidia ION (MCP79) eSata fails for external cabinet Thecus N2050 (SIL5744) Örjan Nordlund
2009-11-09 8:10 ` Tejun Heo
2009-11-12 12:51 ` Örjan Nordlund
2009-11-12 20:04 ` Tejun Heo
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.