* New DMAR errors in Xen 4.1
@ 2010-04-06 22:38 Jeremy Fitzhardinge
2010-04-07 0:00 ` Jeremy Fitzhardinge
0 siblings, 1 reply; 7+ messages in thread
From: Jeremy Fitzhardinge @ 2010-04-06 22:38 UTC (permalink / raw)
To: Keir Fraser; +Cc: Xen-devel
I'm seeing DMAR errors with current Xen-unstable, which weren't there in
-rc8 (-rc9?):
type=1403 audit(1270593095.214:3): policy loaded auid=4294967295 ses=4294967295
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 05h] PTE Write access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 17b
(XEN) l1[17b] = 0
(XEN) l1[17b] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf57a000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 05h] PTE Write access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57a
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 17a
(XEN) l1[17a] = 0
(XEN) l1[17a] not present
Device 0:1f.2 is my SATA controller. I haven't tried bisecting it or
anything yet; I don't see any recent changes which are obviously
relevant though.
J
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: New DMAR errors in Xen 4.1
2010-04-06 22:38 New DMAR errors in Xen 4.1 Jeremy Fitzhardinge
@ 2010-04-07 0:00 ` Jeremy Fitzhardinge
2010-04-07 2:50 ` Weidong Han
0 siblings, 1 reply; 7+ messages in thread
From: Jeremy Fitzhardinge @ 2010-04-07 0:00 UTC (permalink / raw)
To: Keir Fraser; +Cc: Xen-devel
On 04/06/2010 03:38 PM, Jeremy Fitzhardinge wrote:
> I'm seeing DMAR errors with current Xen-unstable, which weren't there
> in -rc8 (-rc9?):
>
> type=1403 audit(1270593095.214:3): policy loaded auid=4294967295
> ses=4294967295
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2]
> fault addr bf57b000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
> bf57b
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 17b
> (XEN) l1[17b] = 0
> (XEN) l1[17b] not present
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2]
> fault addr bf57a000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
> bf57a
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 17a
> (XEN) l1[17a] = 0
> (XEN) l1[17a] not present
>
>
>
> Device 0:1f.2 is my SATA controller. I haven't tried bisecting it or
> anything yet; I don't see any recent changes which are obviously
> relevant though.
It turns out its... "Enable debug=y by default in the build." So I
guess these errors have been happening silently thus far?
J
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: New DMAR errors in Xen 4.1
2010-04-07 0:00 ` Jeremy Fitzhardinge
@ 2010-04-07 2:50 ` Weidong Han
2010-04-07 8:31 ` Cui, Dexuan
2010-04-07 16:55 ` Jeremy Fitzhardinge
0 siblings, 2 replies; 7+ messages in thread
From: Weidong Han @ 2010-04-07 2:50 UTC (permalink / raw)
To: Jeremy Fitzhardinge; +Cc: Xen-devel, Keir Fraser
Jeremy Fitzhardinge wrote:
> On 04/06/2010 03:38 PM, Jeremy Fitzhardinge wrote:
>
>> I'm seeing DMAR errors with current Xen-unstable, which weren't there
>> in -rc8 (-rc9?):
>>
>> type=1403 audit(1270593095.214:3): policy loaded auid=4294967295
>> ses=4294967295
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2]
>> fault addr bf57b000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf57b
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 17b
>> (XEN) l1[17b] = 0
>> (XEN) l1[17b] not present
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2]
>> fault addr bf57a000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf57a
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 17a
>> (XEN) l1[17a] = 0
>> (XEN) l1[17a] not present
>>
>>
>>
>> Device 0:1f.2 is my SATA controller. I haven't tried bisecting it or
>> anything yet; I don't see any recent changes which are obviously
>> relevant though.
>>
>
> It turns out its... "Enable debug=y by default in the build." So I
> guess these errors have been happening silently thus far?
>
> J
>
I don't encounter this issue. These DMAR fault messages will be printed
even when debug=n. what platform are you using? could you post complete
booting log with "iommu=verbose"?
Regards,
Weidong
^ permalink raw reply [flat|nested] 7+ messages in thread
* RE: New DMAR errors in Xen 4.1
2010-04-07 2:50 ` Weidong Han
@ 2010-04-07 8:31 ` Cui, Dexuan
2010-04-07 16:55 ` Jeremy Fitzhardinge
1 sibling, 0 replies; 7+ messages in thread
From: Cui, Dexuan @ 2010-04-07 8:31 UTC (permalink / raw)
To: Han, Weidong, Jeremy Fitzhardinge; +Cc: Xen-devel, Keir Fraser
Weidong Han wrote:
> Jeremy Fitzhardinge wrote:
>> On 04/06/2010 03:38 PM, Jeremy Fitzhardinge wrote:
>>
>>> I'm seeing DMAR errors with current Xen-unstable, which weren't
>>> there in -rc8 (-rc9?):
>>> ...
>>>
>>> Device 0:1f.2 is my SATA controller. I haven't tried bisecting it
>>> or anything yet; I don't see any recent changes which are obviously
>>> relevant though.
>>>
>>
>> It turns out its... "Enable debug=y by default in the build." So I
>> guess these errors have been happening silently thus far?
>>
>> J
>>
> I don't encounter this issue. These DMAR fault messages will be
> printed even when debug=n. what platform are you using? could you
> post complete booting log with "iommu=verbose"?
Hi Jeremy,
My first thought is: the checking of the 2 "if" statements in iommu_set_dom0_mapping() might be buggy.
Please comment them out to see if the error messages will disappear -- if the msgs do disappear, we need to find out why the checking causes the issue.
Thanks,
-- Dexuan
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: New DMAR errors in Xen 4.1
2010-04-07 2:50 ` Weidong Han
2010-04-07 8:31 ` Cui, Dexuan
@ 2010-04-07 16:55 ` Jeremy Fitzhardinge
2010-04-08 2:32 ` Weidong Han
1 sibling, 1 reply; 7+ messages in thread
From: Jeremy Fitzhardinge @ 2010-04-07 16:55 UTC (permalink / raw)
To: Weidong Han; +Cc: Xen-devel, Keir Fraser
On 04/06/2010 07:50 PM, Weidong Han wrote:
>> It turns out its... "Enable debug=y by default in the build." So I
>> guess these errors have been happening silently thus far?
>>
>> J
>
> I don't encounter this issue. These DMAR fault messages will be
> printed even when debug=n. what platform are you using? could you post
> complete booting log with "iommu=verbose"?
This is a Supermicro X8SIL-F system, which is a Lynnfield + Ibex Peak
system.
I've attached two boot logs below. The first is one where there lots of
DMAR errors early, and the system is a disaster (basically doesn't come
up, lots of devices fail to init). Unfortunately it looks like I
mistyped "verbose".
The second boot was immediately after the first and it comes up cleanly
with no DMAR errors at all. So it appears there's some non-determinism
there. The gmfns in the messages always appear to be about he same, so
I wonder if it depends on exactly what pages the kernel ends up
allocating for IO? (It probably also means my bisection results are
suspect.)
(BTW, what's a "type 9" E820 region?)
Thanks,
J
__ __ _ _ _ _ _ _
\ \/ /___ _ __ | || | / | _ _ _ __ ___| |_ __ _| |__ | | ___
\ // _ \ '_ \ | || |_ | |__| | | | '_ \/ __| __/ _` | '_ \| |/ _ \
/ \ __/ | | | |__ _|| |__| |_| | | | \__ \ || (_| | |_) | | __/
/_/\_\___|_| |_| |_|(_)_| \__,_|_| |_|___/\__\__,_|_.__/|_|\___|
(XEN) Xen version 4.1-unstable (jeremy@) (gcc version 4.4.3 20100127 (Red Hat 4.4.3-4) (GCC) ) Tue Apr 6 17:23:29 PDT 2010
(XEN) Latest ChangeSet: Tue Apr 06 17:23:12 2010 -0700 21115:ea6c67dc4577
(XEN) Command line: com2=115200,8n1,0x3e8,5 console=com2,vga cpufreq=xen iommu=verbos8
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 4 MBR signatures
(XEN) Found 4 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009d800 (usable)
(XEN) 000000000009d800 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bf790000 (usable)
(XEN) 00000000bf79e000 - 00000000bf7a0000 type 9
(XEN) 00000000bf7a0000 - 00000000bf7ae000 (ACPI data)
(XEN) 00000000bf7ae000 - 00000000bf7d0000 (ACPI NVS)
(XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved)
(XEN) 00000000bf7ed000 - 00000000c0000000 (reserved)
(XEN) 00000000e0000000 - 00000000f0000000 (reserved)
(XEN) 00000000fed20000 - 00000000fed40000 (reserved)
(XEN) 00000000fee00000 - 00000000fee01000 (reserved)
(XEN) 0000000100000000 - 0000000140000000 (usable)
(XEN) ACPI: RSDP 000FA110, 0024 (r2 ACPIAM)
(XEN) ACPI: XSDT BF7A0100, 0084 (r1 SMCI 20100225 MSFT 97)
(XEN) ACPI: FACP BF7A0290, 00F4 (r4 022510 FACP1918 20100225 MSFT 97)
(XEN) ACPI: DSDT BF7A05F0, 6C55 (r2 10605 10605000 0 INTL 20051117)
(XEN) ACPI: FACS BF7AE000, 0040
(XEN) ACPI: APIC BF7A0390, 0092 (r2 022510 APIC1918 20100225 MSFT 97)
(XEN) ACPI: MCFG BF7A0430, 003C (r1 022510 OEMMCFG 20100225 MSFT 97)
(XEN) ACPI: OEMB BF7AE040, 0073 (r1 022510 OEMB1918 20100225 MSFT 97)
(XEN) ACPI: HPET BF7AA5F0, 0038 (r1 022510 OEMHPET 20100225 MSFT 97)
(XEN) ACPI: GSCI BF7AE0C0, 2024 (r1 022510 GMCHSCI 20100225 MSFT 97)
(XEN) ACPI: DMAR BF7B00F0, 0090 (r1 AMI OEMDMAR 1 MSFT 97)
(XEN) ACPI: SSDT BF7B1580, 0363 (r1 DpgPmm CpuPm 12 INTL 20051117)
(XEN) ACPI: EINJ BF7AA630, 0130 (r1 AMIER AMI_EINJ 20100225 MSFT 97)
(XEN) ACPI: BERT BF7AA7C0, 0030 (r1 AMIER AMI_BERT 20100225 MSFT 97)
(XEN) ACPI: ERST BF7AA7F0, 01B0 (r1 AMIER AMI_ERST 20100225 MSFT 97)
(XEN) ACPI: HEST BF7AA9A0, 00A8 (r1 AMIER ABC_HEST 20100225 MSFT 97)
(XEN) System RAM: 4056MB (4153584kB)
(XEN) No NUMA configuration found
(XEN) Faking a node at 0000000000000000-0000000140000000
(XEN) Domain heap initialised
(XEN) found SMP MP-table at 000ff780
(XEN) DMI present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x808
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0]
(XEN) ACPI: wakeup_vec[bf7ae00c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:14 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
(XEN) Processor #2 7:14 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
(XEN) Processor #4 7:14 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
(XEN) Processor #6 7:14 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled)
(XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
(XEN) ACPI: IOAPIC (id[0x07] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 7, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) ACPI: HPET id: 0x8086a701 base: 0xfed00000
(XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
(XEN) PCI: MCFG area at e0000000 reserved in E820
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Detected 2400.067 MHz processor.
(XEN) Initing memory sharing.
(XEN) EPT support 2M super page.
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Extended Page Tables (EPT)
(XEN) - Virtual-Processor Identifiers (VPID)
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: ASIDs enabled.
(XEN) HVM: VMX enabled
(XEN) HVM: Hardware Assisted Paging detected.
(XEN) Intel machine check reporting enabled
(XEN) Intel VT-d Snoop Control supported.
(XEN) Intel VT-d DMA Passthrough not supported.
(XEN) Intel VT-d Queued Invalidation supported.
(XEN) Intel VT-d Interrupt Remapping not supported.
(XEN) I/O virtualisation enabled
(XEN) I/O virtualisation for PV guests disabled
(XEN) EPT support 2M super page.
(XEN) EPT support 2M super page.
(XEN) EPT support 2M super page.
(XEN) Total of 4 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) TSC is reliable, synchronization unnecessary
(XEN) Platform timer is 14.318MHz HPET
�(XEN) Allocated console ring of 32 KiB.
(XEN) microcode.c:73:d32767 microcode: CPU1 resumed
(XEN) microcode.c:73:d32767 microcode: CPU2 resumed
(XEN) Brought up 4 CPUs
(XEN) microcode.c:73:d32767 microcode: CPU3 resumed
(XEN) Turbo Mode detected!
(XEN) HPET: 8 timers in total, 8 timers will be used for broadcast
(XEN) ACPI sleep modes: S3
(XEN) mcheck_poll: Machine check polling timer started.
(XEN) *** LOADING DOMAIN 0 ***
(XEN) elf_parse_binary: phdr: paddr=0x1000000 memsz=0x69c000
(XEN) elf_parse_binary: phdr: paddr=0x169c000 memsz=0xe3cb0
(XEN) elf_parse_binary: phdr: paddr=0x1780000 memsz=0x888
(XEN) elf_parse_binary: phdr: paddr=0x1781000 memsz=0x14498
(XEN) elf_parse_binary: phdr: paddr=0x1796000 memsz=0x9f5000
(XEN) elf_parse_binary: memory: 0x1000000 -> 0x218b000
(XEN) elf_xen_parse_note: GUEST_OS = "linux"
(XEN) elf_xen_parse_note: GUEST_VERSION = "2.6"
(XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0"
(XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000
(XEN) elf_xen_parse_note: ENTRY = 0xffffffff81796200
(XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff81009000
(XEN) elf_xen_parse_note: FEATURES = "!writable_page_tables|pae_pgdir_above_4gb"
(XEN) elf_xen_parse_note: PAE_MODE = "yes"
(XEN) elf_xen_parse_note: LOADER = "generic"
(XEN) elf_xen_parse_note: unknown xen elf note (0xd)
(XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1
(XEN) elf_xen_parse_note: HV_START_LOW = 0xffff800000000000
(XEN) elf_xen_parse_note: PADDR_OFFSET = 0x0
(XEN) elf_xen_addr_calc_check: addresses:
(XEN) virt_base = 0xffffffff80000000
(XEN) elf_paddr_offset = 0x0
(XEN) virt_offset = 0xffffffff80000000
(XEN) virt_kstart = 0xffffffff81000000
(XEN) virt_kend = 0xffffffff8218b000
(XEN) virt_entry = 0xffffffff81796200
(XEN) p2m_base = 0xffffffffffffffff
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x218b000
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 0000000138000000->000000013c000000 (981633 pages to be allocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff81000000->ffffffff8218b000
(XEN) Init. ramdisk: ffffffff8218b000->ffffffff82b69800
(XEN) Phys-Mach map: ffffffff82b6a000->ffffffff83307408
(XEN) Start info: ffffffff83308000->ffffffff833084b4
(XEN) Page tables: ffffffff83309000->ffffffff83326000
(XEN) Boot stack: ffffffff83326000->ffffffff83327000
(XEN) TOTAL: ffffffff80000000->ffffffff83400000
(XEN) ENTRY ADDRESS: ffffffff81796200
(XEN) Dom0 has maximum 4 VCPUs
(XEN) elf_load_binary: phdr 0 at 0xffffffff81000000 -> 0xffffffff8169c000
(XEN) elf_load_binary: phdr 1 at 0xffffffff8169c000 -> 0xffffffff8177fcb0
(XEN) elf_load_binary: phdr 2 at 0xffffffff81780000 -> 0xffffffff81780888
(XEN) elf_load_binary: phdr 3 at 0xffffffff81781000 -> 0xffffffff81795498
(XEN) elf_load_binary: phdr 4 at 0xffffffff81796000 -> 0xffffffff81830000
(XEN) Scrubbing Free RAM: .done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) Xen is relinquishing VGA console.
(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen)
(XEN) Freed 164kB init memory.
mapping kernel into physical memory
Xen: setup ISA identity maps
about to get started...
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.32.11 (jeremy@lilith.goop.org) (gcc version 4.4.3 20100127 (Red Hat 4.4.3-4) (GCC) ) #7 SMP PREEMPT Mon Apr 5 14:58:54 PDT 2010
Command line: ro root=/dev/mapper/vg_lilith--raid-root LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us ignore_loglevel earlyprintk=xen console=hvc0 rdshell pcie_aspm=off
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
xen_release_chunk: looking at area pfn bf790-bf79e: 14 pages freed
xen_release_chunk: looking at area pfn bf7e0-bf7ed: 13 pages freed
xen_release_chunk: looking at area pfn c0000-e0000: 131072 pages freed
xen_release_chunk: looking at area pfn f0000-fec00: 14977 pages freed
xen_release_chunk: looking at area pfn fec01-fed20: 0 pages freed
xen_release_chunk: looking at area pfn fed40-fee00: 0 pages freed
released 146076 pages of unused memory
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 000000000009d800 (usable)
Xen: 000000000009d800 - 0000000000100000 (reserved)
Xen: 0000000000100000 - 00000000bf790000 (usable)
Xen: 00000000bf79e000 - 00000000bf7a0000 type 9
Xen: 00000000bf7a0000 - 00000000bf7ae000 (ACPI data)
Xen: 00000000bf7ae000 - 00000000bf7d0000 (ACPI NVS)
Xen: 00000000bf7d0000 - 00000000bf7e0000 (reserved)
Xen: 00000000bf7ed000 - 00000000c0000000 (reserved)
Xen: 00000000e0000000 - 00000000f0000000 (reserved)
Xen: 00000000fec00000 - 00000000fec01000 (reserved)
Xen: 00000000fed20000 - 00000000fed40000 (reserved)
Xen: 00000000fee00000 - 00000000fee01000 (reserved)
debug: ignoring loglevel setting.
bootconsole [xenboot0] enabled
DMI present.
last_pfn = 0xbf790 max_arch_pfn = 0x400000000
x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-00000000bf790000
0000000000 - 00bf790000 page 4k
kernel direct mapping tables up to bf790000 @ 100000-700000
RAMDISK: 0218b000 - 02b69800
ACPI: RSDP 00000000000fa110 00024 (v02 ACPIAM)
ACPI: XSDT 00000000bf7a0100 00084 (v01 SMCI 20100225 MSFT 00000097)
ACPI: FACP 00000000bf7a0290 000F4 (v04 022510 FACP1918 20100225 MSFT 00000097)
ACPI: DSDT 00000000bf7a05f0 06C55 (v02 10605 10605000 00000000 INTL 20051117)
ACPI: FACS 00000000bf7ae000 00040
ACPI: APIC 00000000bf7a0390 00092 (v02 022510 APIC1918 20100225 MSFT 00000097)
ACPI: MCFG 00000000bf7a0430 0003C (v01 022510 OEMMCFG 20100225 MSFT 00000097)
ACPI: OEMB 00000000bf7ae040 00073 (v01 022510 OEMB1918 20100225 MSFT 00000097)
ACPI: HPET 00000000bf7aa5f0 00038 (v01 022510 OEMHPET 20100225 MSFT 00000097)
ACPI: GSCI 00000000bf7ae0c0 02024 (v01 022510 GMCHSCI 20100225 MSFT 00000097)
ACPI: 00000000bf7b00f0 00090 (v01 AMI OEMDMAR 00000001 MSFT 00000097)
ACPI: SSDT 00000000bf7b1580 00363 (v01 DpgPmm CpuPm 00000012 INTL 20051117)
ACPI: EINJ 00000000bf7aa630 00130 (v01 AMIER AMI_EINJ 20100225 MSFT 00000097)
ACPI: BERT 00000000bf7aa7c0 00030 (v01 AMIER AMI_BERT 20100225 MSFT 00000097)
ACPI: ERST 00000000bf7aa7f0 001B0 (v01 AMIER AMI_ERST 20100225 MSFT 00000097)
ACPI: HEST 00000000bf7aa9a0 000A8 (v01 AMIER ABC_HEST 20100225 MSFT 00000097)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at 0000000000000000-00000000bf790000
Bootmem setup node 0 0000000000000000-00000000bf790000
NODE_DATA [0000000000001000 - 0000000000005fff]
bootmap [0000000000008000 - 000000000001fef7] pages 18
(8 early reservations) ==> bootmem [0000000000 - 00bf790000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0003309000 - 0003326000] XEN PAGETABLES ==> [0003309000 - 0003326000]
#2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#3 [0001000000 - 000216a048] TEXT DATA BSS ==> [0001000000 - 000216a048]
#4 [000218b000 - 0002b69800] RAMDISK ==> [000218b000 - 0002b69800]
#5 [0002b6a000 - 0003309000] XEN START INFO ==> [0002b6a000 - 0003309000]
#6 [000216b000 - 000216b21b] BRK ==> [000216b000 - 000216b21b]
#7 [0000100000 - 00006e0000] PGTABLE ==> [0000100000 - 00006e0000]
found SMP MP-table at [ffff8800000ff780] ff780
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x0000009d
0: 0x00000100 -> 0x000bf790
On node 0 totalpages: 784173
DMA zone: 88 pages used for memmap
DMA zone: 1507 pages reserved
DMA zone: 2402 pages, LIFO batch:0
DMA32 zone: 16762 pages used for memmap
DMA32 zone: 763414 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled)
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x07] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 7, version 0, address 0xfec00000, GSI 0-0
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ERROR: Unable to locate IOAPIC for GSI 2
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ERROR: Unable to locate IOAPIC for GSI 9
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a701 base: 0xfed00000
SMP: Allowing 4 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 256
PM: Registered nosave memory: 000000000009d000 - 000000000009e000
PM: Registered nosave memory: 000000000009e000 - 0000000000100000
Allocating PCI resources starting at c0000000 (gap: c0000000:20000000)
Booting paravirtualized kernel on Xen
Xen version: 4.1-unstable (preserve-AD) (dom0)
NR_CPUS:16 nr_cpumask_bits:16 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 28 pages/cpu @ffff88000336d000 s83096 r8192 d23400 u114688
pcpu-alloc: s83096 r8192 d23400 u114688 alloc=28*4096
pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
trying to map vcpu_info 0 at ffff880003378020, mfn 13b378, offset 32
cpu 0 using vcpu_info at ffff880003378020
trying to map vcpu_info 1 at ffff880003394020, mfn 13b394, offset 32
cpu 1 using vcpu_info at ffff880003394020
trying to map vcpu_info 2 at ffff8800033b0020, mfn 13b3b0, offset 32
cpu 2 using vcpu_info at ffff8800033b0020
trying to map vcpu_info 3 at ffff8800033cc020, mfn 13b3cc, offset 32
cpu 3 using vcpu_info at ffff8800033cc020
Xen: using vcpu_info placement
Built 1 zonelists in Node order, mobility grouping on. Total pages: 765816
Policy zone: DMA32
Kernel command line: ro root=/dev/mapper/vg_lilith--raid-root LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us ignore_loglevel earlyprintk=xen console=hvc0 rdshell pcie_aspm=off
PCIe ASPM is disabled
PID hash table entries: 4096 (order: 3, 32768 bytes)
Initializing CPU#0
DMA: Placing 64MB software IO TLB between ffff88000794a000 - ffff88000b94a000
DMA: software IO TLB at phys 0x794a000 - 0xb94a000
xen_swiotlb_fixup: buf=ffff88000794a000 size=67108864
xen_swiotlb_fixup: buf=ffff88000b9aa000 size=32768
Memory: 2960308k/3137088k available (4691k kernel code, 396k absent, 176384k reserved, 2987k data, 656k init)
Hierarchical RCU implementation.
NR_IRQS:4352 nr_irqs:1280
xen: --> irq=0
xen: --> irq=1
xen: --> irq=2
xen: --> irq=3
xen: --> irq=4
xen: --> irq=5
xen: --> irq=6
xen: --> irq=7
xen: --> irq=8
xen: --> irq=9
xen: --> irq=10
xen: --> irq=11
xen: --> irq=12
xen: --> irq=13
xen: --> irq=14
xen: --> irq=15
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
xen: sci override: source_irq=9 global_irq=9 trigger=c polarity=1
xen: registering gsi 9 triggering 0 polarity 0
xen_allocate_pirq: returning irq 9 for gsi 9
xen: --> irq=9
xen: acpi sci 9
Console: colour VGA+ 80x25
console [hvc0] enabled, bootconsole disabled
console [hvc0] enabled, bootconsole disabled
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES: 8
... MAX_LOCK_DEPTH: 48
... MAX_LOCKDEP_KEYS: 8191
... CLASSHASH_SIZE: 4096
... MAX_LOCKDEP_ENTRIES: 16384
... MAX_LOCKDEP_CHAINS: 32768
... CHAINHASH_SIZE: 16384
memory used by lock dependency info: 5855 kB
per task-struct memory footprint: 1920 bytes
Xen: using vcpuop timer interface
installing Xen timer for CPU 0
alloc irq_desc for 1279 on node 0
alloc kstat_irqs on node 0
Detected 2400.066 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.13 BogoMIPS (lpj=2400066)
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 0/0x0 -> Node 0
CPU: Unsupported number of siblings 16
Performance Events: unsupported p6 CPU model 30 no PMU driver, software events only.
lockdep: fixing up alternatives.
SMP alternatives: switching to UP code
ACPI: Core revision 20090903
alloc irq_desc for 1278 on node 0
alloc kstat_irqs on node 0
cpu 0 spinlock event irq 1278
alloc irq_desc for 1277 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1276 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1275 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1274 on node 0
alloc kstat_irqs on node 0
installing Xen timer for CPU 1
alloc irq_desc for 1273 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1272 on node 0
alloc kstat_irqs on node 0
cpu 1 spinlock event irq 1272
lockdep: fixing up alternatives.
SMP alternatives: switching to SMP code
alloc irq_desc for 1271 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1270 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1269 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1268 on node 0
alloc kstat_irqs on node 0
Initializing CPU#1
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 1/0x0 -> Node 0
CPU: Unsupported number of siblings 16
installing Xen timer for CPU 2
alloc irq_desc for 1267 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1266 on node 0
alloc kstat_irqs on node 0
cpu 2 spinlock event irq 1266
alloc irq_desc for 1265 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1264 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1263 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1262 on node 0
alloc kstat_irqs on node 0
Initializing CPU#2
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 2/0x0 -> Node 0
CPU: Unsupported number of siblings 16
installing Xen timer for CPU 3
alloc irq_desc for 1261 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1260 on node 0
alloc kstat_irqs on node 0
cpu 3 spinlock event irq 1260
alloc irq_desc for 1259 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1258 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1257 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1256 on node 0
alloc kstat_irqs on node 0
Initializing CPU#3
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 3/0x0 -> Node 0
CPU: Unsupported number of siblings 16
Brought up 4 CPUs
Grant table initialized
Time: 16:42:50 Date: 04/07/10
NET: Registered protocol family 16
alloc irq_desc for 1255 on node 0
alloc kstat_irqs on node 0
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG at e0000000 - efffffff
PCI: Using configuration type 1 for base access
bio: create slab<bio-0> at 0
ERROR: Unable to locate IOAPIC for GSI 9
ACPI: EC: Look up EC in DSDT
ACPI Warning for \_SB_._OSC: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
\_SB_:_OSC evaluation returned wrong type
_OSC request data:1 6
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI Warning: Incorrect checksum in table [OEMB] - 91, should be 8E (20090903/tbutils-314)
ACPI Warning: Incorrect checksum in table [ ] - 7B, should be BF (20090903/tbutils-314)
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:1a.0: reg 10 32bit mmio: [0xfb3fc000-0xfb3fc3ff]
pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.5: PME# disabled
pci 0000:00:1d.0: reg 10 32bit mmio: [0xfb3fa000-0xfb3fa3ff]
pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.0: PME# disabled
pci 0000:00:1f.2: reg 10 io port: [0xb400-0xb407]
pci 0000:00:1f.2: reg 14 io port: [0xbc00-0xbc03]
pci 0000:00:1f.2: reg 18 io port: [0xb880-0xb887]
pci 0000:00:1f.2: reg 1c io port: [0xb800-0xb803]
pci 0000:00:1f.2: reg 20 io port: [0xb480-0xb49f]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xfb3f8000-0xfb3f87ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 10 64bit mmio: [0xfb3f6000-0xfb3f60ff]
pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
pci 0000:03:00.0: reg 10 32bit mmio: [0xfb420000-0xfb43ffff]
pci 0000:03:00.0: reg 14 32bit mmio: [0xfb480000-0xfb4fffff]
pci 0000:03:00.0: reg 18 io port: [0xcc00-0xcc1f]
pci 0000:03:00.0: reg 1c 32bit mmio: [0xfb41c000-0xfb41ffff]
pci 0000:03:00.0: reg 30 32bit mmio pref: [0xfb440000-0xfb47ffff]
pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
pci 0000:03:00.0: PME# disabled
pci 0000:00:1c.0: bridge io port: [0xc000-0xcfff]
pci 0000:00:1c.0: bridge 32bit mmio: [0xfb400000-0xfb4fffff]
pci 0000:04:00.0: reg 10 32bit mmio: [0xfb5e0000-0xfb5fffff]
pci 0000:04:00.0: reg 18 io port: [0xdc00-0xdc1f]
pci 0000:04:00.0: reg 1c 32bit mmio: [0xfb5dc000-0xfb5dffff]
pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
pci 0000:04:00.0: PME# disabled
pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff]
pci 0000:00:1c.4: bridge 32bit mmio: [0xfb500000-0xfb5fffff]
pci 0000:05:00.0: reg 10 32bit mmio: [0xfb6e0000-0xfb6fffff]
pci 0000:05:00.0: reg 18 io port: [0xec00-0xec1f]
pci 0000:05:00.0: reg 1c 32bit mmio: [0xfb6dc000-0xfb6dffff]
pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
pci 0000:05:00.0: PME# disabled
pci 0000:00:1c.5: bridge io port: [0xe000-0xefff]
pci 0000:00:1c.5: bridge 32bit mmio: [0xfb600000-0xfb6fffff]
pci 0000:06:03.0: reg 10 32bit mmio pref: [0xfa000000-0xfaffffff]
pci 0000:06:03.0: reg 14 32bit mmio: [0xfb7fc000-0xfb7fffff]
pci 0000:06:03.0: reg 18 32bit mmio: [0xfb800000-0xfbffffff]
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge 32bit mmio: [0xfb700000-0xfbffffff]
pci 0000:00:1e.0: bridge 64bit mmio pref: [0xfa000000-0xfaffffff]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR1E._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR20._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR24._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR25._PRT]
(XEN) PCI add device 00:00.0
(XEN) PCI add device 00:03.0
(XEN) PCI add device 00:05.0
(XEN) PCI add device 00:08.0
(XEN) PCI add device 00:08.1
(XEN) PCI add device 00:08.2
(XEN) PCI add device 00:08.3
(XEN) PCI add device 00:10.0
(XEN) PCI add device 00:10.1
(XEN) PCI add device 00:1a.0
(XEN) PCI add device 00:1c.0
(XEN) PCI add device 00:1c.4
(XEN) PCI add device 00:1c.5
(XEN) PCI add device 00:1d.0
(XEN) PCI add device 00:1e.0
(XEN) PCI add device 00:1f.0
(XEN) PCI add device 00:1f.2
(XEN) PCI add device 00:1f.3
(XEN) PCI add device 03:00.0
(XEN) PCI add device 04:00.0
(XEN) PCI add device 05:00.0
(XEN) PCI add device 06:03.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 6 7 10 11 12 14 *15)
sync cpu 0 get result 1 max_id 3
sync cpu 1 get result 1 max_id 3
sync cpu 2 get result 1 max_id 3
sync cpu 3 get result 1 max_id 3
alloc irq_desc for 1254 on node 0
alloc kstat_irqs on node 0
xen_balloon: Initialising balloon driver with page order 0.
vgaarb: device added: PCI:0000:06:03.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Switching to clocksource xen
pnp: PnP ACPI init
ACPI: bus type pnp registered
xen: registering gsi 8 triggering 1 polarity 0
xen_allocate_pirq: returning irq 8 for gsi 8
xen:scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8100 irq 1247
ata2: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8180 irq 1247
ata3: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8200 irq 1247
ata4: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8280 irq 1247
ata5: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8300 irq 1247
ata6: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8380 irq 1247
usb 1-1: udev 2, busnum 1, minor = 1
usb 1-1: New USB device found, idVendor=8087, idProduct=0020
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: usb_probe_device
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
hub 1-1:1.0: usb_probe_interface
hub 1-1:1.0: usb_probe_interface - got id
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 6 ports detected
hub 1-1:1.0: standalone hub
hub 1-1:1.0: individual port power switching
hub 1-1:1.0: individual port over-current protection
hub 1-1:1.0: Single TT
hub 1-1:1.0: TT requires at most 8 FS bit times (666 ns)
hub 1-1:1.0: Port indicators are supported
hub 1-1:1.0: power on to power good time: 100ms
hub 1-1:1.0: local power source is good
hub 1-1:1.0: enabling power on all ports
hub 2-0:1.0: state 7 ports 2 chg 0002 evt 0000
hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:1d.0: port 1 high speed
ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
hub 1-1:1.0: port 2: status 0101 change 0001
usb 2-1: new high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.0: port 1 high speed
ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 1-1: link qh256-0001/ffff8800bcd9ab40 start 1 [1/0 us]
usb 2-1: udev 2, busnum 2, minor = 129
usb 2-1: New USB device found, idVendor=8087, idProduct=0020
usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 2-1: usb_probe_device
usb 2-1: configuration #1 chosen from 1 choice
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
hub 2-1:1.0: usb_probe_interface
hub 2-1:1.0: usb_probe_interface - got id
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 8 ports detected
hub 2-1:1.0: standalone hub
hub 2-1:1.0: individual port power switching
hub 2-1:1.0: individual port over-current protection
hub 2-1:1.0: Single TT
hub 2-1:1.0: TT requires at most 8 FS bit times (666 ns)
hub 2-1:1.0: Port indicators are supported
hub 2-1:1.0: power on to power good time: 100ms
hub 2-1:1.0: local power source is good
hub 2-1:1.0: enabling power on all ports
hub 1-1:1.0: state 7 ports 6 chg 0004 evt 0000
hub 1-1:1.0: port 2, status 0101, change 0000, 12 Mb/s
usb 1-1.2: new full speed USB device using ehci_hcd and address 3
hub 1-1:1.0: port 2 not reset yet, waiting 10ms
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: WDC WD10EADS-00P8B0, 01.00A01, max UDMA/133
ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA WDC WD10EADS-00P 01.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: Attached scsi generic sg0 type 0
sda:
usb 2-1: link qh256-0001/ffff8800be450cc0 start 1 [1/0 us]
sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
usb 1-1.2: skipped 1 descriptor after interface
usb 1-1.2: skipped 1 descriptor after interface
usb 1-1.2: default language 0x0409
usb 1-1.2: udev 3, busnum 1, minor = 2
usb 1-1.2: New USB device found, idVendor=0557, idProduct=2221
usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.2: Product: Hermon USB hidmouse Device
usb 1-1.2: Manufacturer: Winbond Electronics Corp
usb 1-1.2: usb_probe_device
usb 1-1.2: configuration #1 chosen from 1 choice
usb 1-1.2: adding 1-1.2:1.0 (config #1, interface 0)
usbhid 1-1.2:1.0: usb_probe_interface
usbhid 1-1.2:1.0: usb_probe_interface - got id
input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input4
generic-usb 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:1a.0-1.2/input0
usb 1-1.2: adding 1-1.2:1.1 (config #1, interface 1)
usbhid 1-1.2:1.1: usb_probe_interface
usbhid 1-1.2:1.1: usb_probe_interface - got id
input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.1/input/input5
usb 1-1.2: link qh8-0601/ffff8800bc52e440 start 2 [1/2 us]
generic-usb 0003:0557:2221.0002: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:1a.0-1.2/input1
hub 2-1:1.0: state 7 ports 8 chg 0000 evt 0000
hub 1-1:1.0: state 7 ports 6 chg 0000 evt 0004
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 sdb3 sdb4
sd 1:0:0:0: [sdb] Attached SCSI disk
input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input6
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-8: WDC WD10EADS-00P8B0, 01.00A01, max UDMA/133
ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
ata3.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA WDC WD10EADS-00P 01.0 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1 sdc2 sdc3 sdc4
sd 2:0:0:0: [sdc] Attached SCSI disk
hub 2-1:1.0: hub_suspend
usb 2-1: unlink qh256-0001/ffff8800be450cc0 start 1 [1/0 us]
usb 2-1: usb auto-suspend
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
ata4.00: configured for UDMA/133
scsi 3:0:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5
sd 3:0:0:0: [sdd] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
sd 3:0:0:0: Attached scsi generic sg3 type 0
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1 sdd2 sdd3 sdd4
sd 3:0:0:0: [sdd] Attached SCSI disk
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
md: raid10 personality registered for level 10
Intel AES-NI instructions are not detected.
md: md0 stopped.
md: bind<sdb3>
md: bind<sdc3>
md: bind<sdd3>
md: bind<sda3>
raid10: md0 is not clean -- starting background reconstruction
raid10: raid set md0 active with 4 out of 4 devices
md0: detected capacity change from 0 to 838860668928
md: resync of RAID array md0
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
md: using 128k window, over a total of 819199872 blocks.
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf579000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 05h] PTE Write access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf579
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 179
(XEN) l1[179] = 0
(XEN) l1[179] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf579000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 05h] PTE Write access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf579
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 179
(XEN) l1[179] = 0
(XEN) l1[179] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 05h] PTE Write access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 178
(XEN) l1[178] = 0
(XEN) l1[178] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 05h] PTE Write access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 178
(XEN) l1[178] = 0
(XEN) l1[178] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 05h] PTE Write access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 17b
(XEN) l1[17b] = 0
(XEN) l1[17b] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 05h] PTE Write access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 17b
(XEN) l1[17b] = 0
(XEN) l1[17b] not present
md0:(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 06h] PTE Read access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 17b
(XEN) l1[17b] = 0
(XEN) l1[17b] not present
ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
ata2.00: irq_stat 0x20000000, host bus error
ata2: SError: { HostInt }
ata2.00: failed command: WRITE FPDMA QUEUED
ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata2.00: status: { DRDY }
ata2: hard resetting link
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: configured for UDMA/133
ata2: EH complete
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 06h] PTE Read access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 17b
(XEN) l1[17b] = 0
(XEN) l1[17b] not present
ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
ata2.00: irq_stat 0x20000000, host bus error
ata2: SError: { HostInt }
ata2.00: failed command: WRITE FPDMA QUEUED
ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata2.00: status: { DRDY }
ata2: hard resetting link
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: configured for UDMA/133
ata2: EH complete
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 06h] PTE Read access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 17b
(XEN) l1[17b] = 0
(XEN) l1[17b] not present
ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
ata2.00: irq_stat 0x20000000, host bus error
ata2: SError: { HostInt }
ata2.00: failed command: WRITE FPDMA QUEUED
ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata2.00: status: { DRDY }
ata2: hard resetting link
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: configured for UDMA/133
ata2: EH complete
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 06h] PTE Read access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 17b
(XEN) l1[17b] = 0
(XEN) l1[17b] not present
ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
ata2.00: irq_stat 0x20000000, host bus error
ata2: SError: { HostInt }
ata2.00: failed command: WRITE FPDMA QUEUED
ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata2.00: status: { DRDY }
ata2: hard resetting link
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: configured for UDMA/133
ata2: EH complete
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 06h] PTE Read access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 17b
(XEN) l1[17b] = 0
(XEN) l1[17b] not present
ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
ata2.00: irq_stat 0x20000000, host bus error
ata2: SError: { HostInt }
ata2.00: failed command: WRITE FPDMA QUEUED
ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata2.00: status: { DRDY }
ata2: hard resetting link
hub 2-0:1.0: hub_suspend
usb usb2: bus auto-suspend
ehci_hcd 0000:00:1d.0: suspend root hub
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: configured for UDMA/133
ata2: EH complete
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 06h] PTE Read access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 17b
(XEN) l1[17b] = 0
(XEN) l1[17b] not present
ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
ata2.00: irq_stat 0x20000000, host bus error
ata2: SError: { HostInt }
ata2.00: failed command: WRITE FPDMA QUEUED
ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata2.00: status: { DRDY }
ata2: hard resetting link
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: configured for UDMA/133
sd 1:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 1:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
0c a0 aa c3
sd 1:0:0:0: [sdb] Add. Sense: No additional sense information
sd 1:0:0:0: [sdb] CDB: Write(10): 2a 00 0c a0 aa c3 00 00 80 00
end_request: I/O error, dev sdb, sector 211856067
raid10: Disk failure on sdb3, disabling device.
raid10: Operation continuing on 3 devices.
ata2: EH complete
unknown partition table
md: md0: resync done.
md: checkpointing resync of md0.
RAID10 conf printout:
--- wd:3 rd:4
disk 0, wo:0, o:1, dev:sda3
disk 1, wo:1, o:0, dev:sdb3
disk 2, wo:0, o:1, dev:sdc3
disk 3, wo:0, o:1, dev:sdd3
RAID10 conf printout:
--- wd:3 rd:4
disk 0, wo:0, o:1, dev:sda3
disk 2, wo:0, o:1, dev:sdc3
disk 3, wo:0, o:1, dev:sdd3
md: resync of RAID array md0
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
md: using 128k window, over a total of 819199872 blocks.
md: resuming resync of md0 from checkpoint.
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 05h] PTE Write access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 178
(XEN) l1[178] = 0
(XEN) l1[178] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf579000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 05h] PTE Write access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf579
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 179
(XEN) l1[179] = 0
(XEN) l1[179] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 05h] PTE Write access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 17b
(XEN) l1[17b] = 0
(XEN) l1[17b] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 05h] PTE Write access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 17b
(XEN) l1[17b] = 0
(XEN) l1[17b] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 06h] PTE Read access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 17b
(XEN) l1[17b] = 0
(XEN) l1[17b] not present
ata4.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
ata4.00: irq_stat 0x20000000, host bus error
ata4: SError: { HostInt }
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/80:00:43:b2:a1/00:00:0c:00:00/40 tag 0 ncq 65536 out
res 40/00:04:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: configured for UDMA/133
ata4: EH complete
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 06h] PTE Read access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 178
(XEN) l1[178] = 0
(XEN) l1[178] not present
ata4.00: exception Emask 0x60 SAct 0x3 SErr 0x800 action 0x6 frozen
ata4.00: irq_stat 0x20000000, host bus error
ata4: SError: { HostInt }
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/80:00:43:b2:a1/00:00:0c:00:00/40 tag 0 ncq 65536 out
res 40/00:0c:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/80:08:43:b1:a1/00:00:0c:00:00/40 tag 1 ncq 65536 out
res 40/00:0c:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: configured for UDMA/133
ata4: EH complete
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 06h] PTE Read access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 178
(XEN) l1[178] = 0
(XEN) l1[178] not present
ata4.00: exception Emask 0x60 SAct 0x3 SErr 0x800 action 0x6 frozen
ata4.00: irq_stat 0x20000000, host bus error
ata4: SError: { HostInt }
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/80:00:43:b1:a1/00:00:0c:00:00/40 tag 0 ncq 65536 out
res 40/00:0c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/80:08:43:b2:a1/00:00:0c:00:00/40 tag 1 ncq 65536 out
res 40/00:0c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: configured for UDMA/133
ata4: EH complete
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 06h] PTE Read access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 178
(XEN) l1[178] = 0
(XEN) l1[178] not present
ata4.00: exception Emask 0x60 SAct 0x3f SErr 0x800 action 0x6 frozen
ata4.00: irq_stat 0x20000000, host bus error
ata4: SError: { HostInt }
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/80:00:43:b2:a1/00:00:0c:00:00/40 tag 0 ncq 65536 out
res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/80:08:43:b1:a1/00:00:0c:00:00/40 tag 1 ncq 65536 out
res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:10:43:2d:a2/04:00:0c:00:00/40 tag 2 ncq 524288 in
res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:18:43:31:a2/04:00:0c:00:00/40 tag 3 ncq 524288 in
res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:20:43:35:a2/04:00:0c:00:00/40 tag 4 ncq 524288 in
res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:28:43:39:a2/04:00:0c:00:00/40 tag 5 ncq 524288 in
res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: configured for UDMA/133
ata4: EH complete
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 06h] PTE Read access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 178
(XEN) l1[178] = 0
(XEN) l1[178] not present
ata4.00: exception Emask 0x60 SAct 0x3f SErr 0x800 action 0x6 frozen
ata4.00: irq_stat 0x20000000, host bus error
ata4: SError: { HostInt }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:00:43:39:a2/04:00:0c:00:00/40 tag 0 ncq 524288 in
res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:08:43:35:a2/04:00:0c:00:00/40 tag 1 ncq 524288 in
res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:10:43:31:a2/04:00:0c:00:00/40 tag 2 ncq 524288 in
res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:18:43:2d:a2/04:00:0c:00:00/40 tag 3 ncq 524288 in
res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/80:20:43:b1:a1/00:00:0c:00:00/40 tag 4 ncq 65536 out
res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/80:28:43:b2:a1/00:00:0c:00:00/40 tag 5 ncq 65536 out
res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: configured for UDMA/133
ata4: EH complete
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 06h] PTE Read access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 178
(XEN) l1[178] = 0
(XEN) l1[178] not present
ata4.00: exception Emask 0x60 SAct 0x3f SErr 0x800 action 0x6 frozen
ata4.00: irq_stat 0x20000000, host bus error
ata4: SError: { HostInt }
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/80:00:43:b2:a1/00:00:0c:00:00/40 tag 0 ncq 65536 out
res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/80:08:43:b1:a1/00:00:0c:00:00/40 tag 1 ncq 65536 out
res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:10:43:2d:a2/04:00:0c:00:00/40 tag 2 ncq 524288 in
res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:18:43:31:a2/04:00:0c:00:00/40 tag 3 ncq 524288 in
res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:20:43:35:a2/04:00:0c:00:00/40 tag 4 ncq 524288 in
res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:28:43:39:a2/04:00:0c:00:00/40 tag 5 ncq 524288 in
res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: configured for UDMA/133
sd 3:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 3:0:0:0: [sdd] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
0c a2 39 43
sd 3:0:0:0: [sdd] Add. Sense: No additional sense information
sd 3:0:0:0: [sdd] CDB: Write(10): 2a 00 0c a1 b2 43 00 00 80 00
end_request: I/O error, dev sdd, sector 211923523
raid10: Disk failure on sdd3, disabling device.
raid10: Operation continuing on 2 devices.
ata4: EH complete
md: md0: resync done.
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 06h] PTE Read access is not set
(XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
(XEN) root_entry = ffff83013ff36000
(XEN) root_entry[0] = 13c6bb001
(XEN) context = ffff83013c6bb000
(XEN) context[fa] = 2_13fec4001
(XEN) l4 = ffff83013fec4000
(XEN) l4_index = 0
(XEN) l4[0] = 13fec1003
(XEN) l3 = ffff83013fec1000
(XEN) l3_index = 2
(XEN) l3[2] = 13ccbe003
(XEN) l2 = ffff83013ccbe000
(XEN) l2_index = 1fa
(XEN) l2[1fa] = 13cac3003
(XEN) l1 = ffff83013cac3000
(XEN) l1_index = 178
(XEN) l1[178] = 0
(XEN) l1[178] not present
ata4.00: exception Emask 0x60 SAct 0x1f SErr 0x800 action 0x6 frozen
ata4.00: irq_stat 0x20000000, host bus error
ata4: SError: { HostInt }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:00:43:39:a2/04:00:0c:00:00/40 tag 0 ncq 524288 in
res 40/00:24:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:08:43:35:a2/04:00:0c:00:00/40 tag 1 ncq 524288 in
res 40/00:24:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:10:43:31:a2/04:00:0c:00:00/40 tag 2 ncq 524288 in
res 40/00:24:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:18:43:2d:a2/04:00:0c:00:00/40 tag 3 ncq 524288 in
res 40/00:24:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/80:20:43:b1:a1/00:00:0c:00:00/40 tag 4 ncq 65536 out
res 40/00:24:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: configured for UDMA/133
sd 3:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 3:0:0:0: [sdd] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
0c a1 b1 43
sd 3:0:0:0: [sdd] Add. Sense: No additional sense information
sd 3:0:0:0: [sdd] CDB: Write(10): 2a 00 0c a1 b1 43 00 00 80 00
end_request: I/O error, dev sdd, sector 211923267
ata4: EH complete
md: checkpointing resync of md0.
RAID10 conf printout:
--- wd:2 rd:4
disk 0, wo:0, o:1, dev:sda3
disk 2, wo:0, o:1, dev:sdc3
disk 3, wo:1, o:0, dev:sdd3
RAID10 conf printout:
--- wd:2 rd:4
disk 0, wo:0, o:1, dev:sda3
disk 2, wo:0, o:1, dev:sdc3
md: resync of RAID array md0
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
md: using 128k window, over a total of 819199872 blocks.
md: resuming resync of md0 from checkpoint.
md: md0: resync done.
RAID10 conf printout:
--- wd:2 rd:4
disk 0, wo:0, o:1, dev:sda3
disk 2, wo:0, o:1, dev:sdc3
=========================================================================
__ __ _ _ _ _ _ _
\ \/ /___ _ __ | || | / | _ _ _ __ ___| |_ __ _| |__ | | ___
\ // _ \ '_ \ | || |_ | |__| | | | '_ \/ __| __/ _` | '_ \| |/ _ \
/ \ __/ | | | |__ _|| |__| |_| | | | \__ \ || (_| | |_) | | __/
/_/\_\___|_| |_| |_|(_)_| \__,_|_| |_|___/\__\__,_|_.__/|_|\___|
(XEN) Xen version 4.1-unstable (jeremy@) (gcc version 4.4.3 20100127 (Red Hat 4.4.3-4) (GCC) ) Tue Apr 6 17:23:29 PDT 2010
(XEN) Latest ChangeSet: Tue Apr 06 17:23:12 2010 -0700 21115:ea6c67dc4577
(XEN) Command line: com2=115200,8n1,0x3e8,5 console=com2,vga cpufreq=xen iommu=verbose
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 4 MBR signatures
(XEN) Found 4 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009d800 (usable)
(XEN) 000000000009d800 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bf790000 (usable)
(XEN) 00000000bf79e000 - 00000000bf7a0000 type 9
(XEN) 00000000bf7a0000 - 00000000bf7ae000 (ACPI data)
(XEN) 00000000bf7ae000 - 00000000bf7d0000 (ACPI NVS)
(XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved)
(XEN) 00000000bf7ed000 - 00000000c0000000 (reserved)
(XEN) 00000000e0000000 - 00000000f0000000 (reserved)
(XEN) 00000000fed20000 - 00000000fed40000 (reserved)
(XEN) 00000000fee00000 - 00000000fee01000 (reserved)
(XEN) 0000000100000000 - 0000000140000000 (usable)
(XEN) ACPI: RSDP 000FA110, 0024 (r2 ACPIAM)
(XEN) ACPI: XSDT BF7A0100, 0084 (r1 SMCI 20100225 MSFT 97)
(XEN) ACPI: FACP BF7A0290, 00F4 (r4 022510 FACP1918 20100225 MSFT 97)
(XEN) ACPI: DSDT BF7A05F0, 6C55 (r2 10605 10605000 0 INTL 20051117)
(XEN) ACPI: FACS BF7AE000, 0040
(XEN) ACPI: APIC BF7A0390, 0092 (r2 022510 APIC1918 20100225 MSFT 97)
(XEN) ACPI: MCFG BF7A0430, 003C (r1 022510 OEMMCFG 20100225 MSFT 97)
(XEN) ACPI: OEMB BF7AE040, 0073 (r1 022510 OEMB1918 20100225 MSFT 97)
(XEN) ACPI: HPET BF7AA5F0, 0038 (r1 022510 OEMHPET 20100225 MSFT 97)
(XEN) ACPI: GSCI BF7AE0C0, 2024 (r1 022510 GMCHSCI 20100225 MSFT 97)
(XEN) ACPI: DMAR BF7B00F0, 0090 (r1 AMI OEMDMAR 1 MSFT 97)
(XEN) ACPI: SSDT BF7B1580, 0363 (r1 DpgPmm CpuPm 12 INTL 20051117)
(XEN) ACPI: EINJ BF7AA630, 0130 (r1 AMIER AMI_EINJ 20100225 MSFT 97)
(XEN) ACPI: BERT BF7AA7C0, 0030 (r1 AMIER AMI_BERT 20100225 MSFT 97)
(XEN) ACPI: ERST BF7AA7F0, 01B0 (r1 AMIER AMI_ERST 20100225 MSFT 97)
(XEN) ACPI: HEST BF7AA9A0, 00A8 (r1 AMIER ABC_HEST 20100225 MSFT 97)
(XEN) System RAM: 4056MB (4153584kB)
(XEN) No NUMA configuration found
(XEN) Faking a node at 0000000000000000-0000000140000000
(XEN) Domain heap initialised
(XEN) found SMP MP-table at 000ff780
(XEN) DMI present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x808
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0]
(XEN) ACPI: wakeup_vec[bf7ae00c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:14 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
(XEN) Processor #2 7:14 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
(XEN) Processor #4 7:14 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
(XEN) Processor #6 7:14 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled)
(XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
(XEN) ACPI: IOAPIC (id[0x07] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 7, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) ACPI: HPET id: 0x8086a701 base: 0xfed00000
(XEN) [VT-D]dmar.c:679: Host address width 36
(XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD:
(XEN) [VT-D]dmar.c:398: dmaru->address = fed90000
(XEN) [VT-D]dmar.c:411: flags: INCLUDE_ALL
(XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0
(XEN) [VT-D]dmar.c:571: RMRR region: base_addr ed000 end_address effff
(XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0
(XEN) [VT-D]dmar.c:571: RMRR region: base_addr bf7ed000 end_address bf7fffff
(XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
(XEN) PCI: MCFG area at e0000000 reserved in E820
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Detected 2400.063 MHz processor.
(XEN) Initing memory sharing.
(XEN) EPT support 2M super page.
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Extended Page Tables (EPT)
(XEN) - Virtual-Processor Identifiers (VPID)
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: ASIDs enabled.
(XEN) HVM: VMX enabled
(XEN) HVM: Hardware Assisted Paging detected.
(XEN) Intel machine check reporting enabled
(XEN) [VT-D]iommu.c:1078: drhd->address = fed90000 iommu->reg = ffff82c3fff57000
(XEN) [VT-D]iommu.c:1080: cap = c90780106f0462 ecap = f020e3
(XEN) Intel VT-d Snoop Control supported.
(XEN) Intel VT-d DMA Passthrough not supported.
(XEN) Intel VT-d Queued Invalidation supported.
(XEN) Intel VT-d Interrupt Remapping not supported.
(XEN) I/O virtualisation enabled
(XEN) I/O virtualisation for PV guests disabled
(XEN) EPT support 2M super page.
(XEN) EPT support 2M super page.
(XEN) EPT support 2M super page.
(XEN) Total of 4 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) TSC is reliable, synchronization unnecessary
(XEN) Platform timer is 14.318MHz HPET
�(XEN) Allocated console ring of 32 KiB.
(XEN) microcode.c:73:d32767 microcode: CPU1 resumed
(XEN) microcode.c:73:d32767 microcode: CPU2 resumed
(XEN) Brought up 4 CPUs
(XEN) microcode.c:73:d32767 microcode: CPU3 resumed
(XEN) Turbo Mode detected!
(XEN) HPET: 8 timers in total, 8 timers will be used for broadcast
(XEN) ACPI sleep modes: S3
(XEN) mcheck_poll: Machine check polling timer started.
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:0.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:8.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:8.1
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:8.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:8.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:10.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:10.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 3:0.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 4:0.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 5:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.4
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.5
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.6
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.7
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.4
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.3
(XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg = ffff82c3fff57000
(XEN) *** LOADING DOMAIN 0 ***
(XEN) elf_parse_binary: phdr: paddr=0x1000000 memsz=0x69c000
(XEN) elf_parse_binary: phdr: paddr=0x169c000 memsz=0xe3cb0
(XEN) elf_parse_binary: phdr: paddr=0x1780000 memsz=0x888
(XEN) elf_parse_binary: phdr: paddr=0x1781000 memsz=0x14498
(XEN) elf_parse_binary: phdr: paddr=0x1796000 memsz=0x9f5000
(XEN) elf_parse_binary: memory: 0x1000000 -> 0x218b000
(XEN) elf_xen_parse_note: GUEST_OS = "linux"
(XEN) elf_xen_parse_note: GUEST_VERSION = "2.6"
(XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0"
(XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000
(XEN) elf_xen_parse_note: ENTRY = 0xffffffff81796200
(XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff81009000
(XEN) elf_xen_parse_note: FEATURES = "!writable_page_tables|pae_pgdir_above_4gb"
(XEN) elf_xen_parse_note: PAE_MODE = "yes"
(XEN) elf_xen_parse_note: LOADER = "generic"
(XEN) elf_xen_parse_note: unknown xen elf note (0xd)
(XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1
(XEN) elf_xen_parse_note: HV_START_LOW = 0xffff800000000000
(XEN) elf_xen_parse_note: PADDR_OFFSET = 0x0
(XEN) elf_xen_addr_calc_check: addresses:
(XEN) virt_base = 0xffffffff80000000
(XEN) elf_paddr_offset = 0x0
(XEN) virt_offset = 0xffffffff80000000
(XEN) virt_kstart = 0xffffffff81000000
(XEN) virt_kend = 0xffffffff8218b000
(XEN) virt_entry = 0xffffffff81796200
(XEN) p2m_base = 0xffffffffffffffff
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x218b000
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 0000000138000000->000000013c000000 (981633 pages to be allocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff81000000->ffffffff8218b000
(XEN) Init. ramdisk: ffffffff8218b000->ffffffff82b69800
(XEN) Phys-Mach map: ffffffff82b6a000->ffffffff83307408
(XEN) Start info: ffffffff83308000->ffffffff833084b4
(XEN) Page tables: ffffffff83309000->ffffffff83326000
(XEN) Boot stack: ffffffff83326000->ffffffff83327000
(XEN) TOTAL: ffffffff80000000->ffffffff83400000
(XEN) ENTRY ADDRESS: ffffffff81796200
(XEN) Dom0 has maximum 4 VCPUs
(XEN) elf_load_binary: phdr 0 at 0xffffffff81000000 -> 0xffffffff8169c000
(XEN) elf_load_binary: phdr 1 at 0xffffffff8169c000 -> 0xffffffff8177fcb0
(XEN) elf_load_binary: phdr 2 at 0xffffffff81780000 -> 0xffffffff81780888
(XEN) elf_load_binary: phdr 3 at 0xffffffff81781000 -> 0xffffffff81795498
(XEN) elf_load_binary: phdr 4 at 0xffffffff81796000 -> 0xffffffff81830000
(XEN) Scrubbing Free RAM: .done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) Xen is relinquishing VGA console.
(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen)
(XEN) Freed 164kB init memory.
mapping kernel into physical memory
Xen: setup ISA identity maps
about to get started...
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.32.11 (jeremy@lilith.goop.org) (gcc version 4.4.3 20100127 (Red Hat 4.4.3-4) (GCC) ) #7 SMP PREEMPT Mon Apr 5 14:58:54 PDT 2010
Command line: ro root=/dev/mapper/vg_lilith--raid-root LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us ignore_loglevel earlyprintk=xen console=hvc0 rdshell pcie_aspm=off
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
xen_release_chunk: looking at area pfn bf790-bf79e: 14 pages freed
xen_release_chunk: looking at area pfn bf7e0-bf7ed: 13 pages freed
xen_release_chunk: looking at area pfn c0000-e0000: 131072 pages freed
xen_release_chunk: looking at area pfn f0000-fec00: 14977 pages freed
xen_release_chunk: looking at area pfn fec01-fed20: 0 pages freed
xen_release_chunk: looking at area pfn fed40-fee00: 0 pages freed
released 146076 pages of unused memory
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 000000000009d800 (usable)
Xen: 000000000009d800 - 0000000000100000 (reserved)
Xen: 0000000000100000 - 00000000bf790000 (usable)
Xen: 00000000bf79e000 - 00000000bf7a0000 type 9
Xen: 00000000bf7a0000 - 00000000bf7ae000 (ACPI data)
Xen: 00000000bf7ae000 - 00000000bf7d0000 (ACPI NVS)
Xen: 00000000bf7d0000 - 00000000bf7e0000 (reserved)
Xen: 00000000bf7ed000 - 00000000c0000000 (reserved)
Xen: 00000000e0000000 - 00000000f0000000 (reserved)
Xen: 00000000fec00000 - 00000000fec01000 (reserved)
Xen: 00000000fed20000 - 00000000fed40000 (reserved)
Xen: 00000000fee00000 - 00000000fee01000 (reserved)
debug: ignoring loglevel setting.
bootconsole [xenboot0] enabled
DMI present.
last_pfn = 0xbf790 max_arch_pfn = 0x400000000
x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-00000000bf790000
0000000000 - 00bf790000 page 4k
kernel direct mapping tables up to bf790000 @ 100000-700000
RAMDISK: 0218b000 - 02b69800
ACPI: RSDP 00000000000fa110 00024 (v02 ACPIAM)
ACPI: XSDT 00000000bf7a0100 00084 (v01 SMCI 20100225 MSFT 00000097)
ACPI: FACP 00000000bf7a0290 000F4 (v04 022510 FACP1918 20100225 MSFT 00000097)
ACPI: DSDT 00000000bf7a05f0 06C55 (v02 10605 10605000 00000000 INTL 20051117)
ACPI: FACS 00000000bf7ae000 00040
ACPI: APIC 00000000bf7a0390 00092 (v02 022510 APIC1918 20100225 MSFT 00000097)
ACPI: MCFG 00000000bf7a0430 0003C (v01 022510 OEMMCFG 20100225 MSFT 00000097)
ACPI: OEMB 00000000bf7ae040 00073 (v01 022510 OEMB1918 20100225 MSFT 00000097)
ACPI: HPET 00000000bf7aa5f0 00038 (v01 022510 OEMHPET 20100225 MSFT 00000097)
ACPI: GSCI 00000000bf7ae0c0 02024 (v01 022510 GMCHSCI 20100225 MSFT 00000097)
ACPI: 00000000bf7b00f0 00090 (v01 AMI OEMDMAR 00000001 MSFT 00000097)
ACPI: SSDT 00000000bf7b1580 00363 (v01 DpgPmm CpuPm 00000012 INTL 20051117)
ACPI: EINJ 00000000bf7aa630 00130 (v01 AMIER AMI_EINJ 20100225 MSFT 00000097)
ACPI: BERT 00000000bf7aa7c0 00030 (v01 AMIER AMI_BERT 20100225 MSFT 00000097)
ACPI: ERST 00000000bf7aa7f0 001B0 (v01 AMIER AMI_ERST 20100225 MSFT 00000097)
ACPI: HEST 00000000bf7aa9a0 000A8 (v01 AMIER ABC_HEST 20100225 MSFT 00000097)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at 0000000000000000-00000000bf790000
Bootmem setup node 0 0000000000000000-00000000bf790000
NODE_DATA [0000000000001000 - 0000000000005fff]
bootmap [0000000000008000 - 000000000001fef7] pages 18
(8 early reservations) ==> bootmem [0000000000 - 00bf790000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0003309000 - 0003326000] XEN PAGETABLES ==> [0003309000 - 0003326000]
#2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#3 [0001000000 - 000216a048] TEXT DATA BSS ==> [0001000000 - 000216a048]
#4 [000218b000 - 0002b69800] RAMDISK ==> [000218b000 - 0002b69800]
#5 [0002b6a000 - 0003309000] XEN START INFO ==> [0002b6a000 - 0003309000]
#6 [000216b000 - 000216b21b] BRK ==> [000216b000 - 000216b21b]
#7 [0000100000 - 00006e0000] PGTABLE ==> [0000100000 - 00006e0000]
found SMP MP-table at [ffff8800000ff780] ff780
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x0000009d
0: 0x00000100 -> 0x000bf790
On node 0 totalpages: 784173
DMA zone: 88 pages used for memmap
DMA zone: 1507 pages reserved
DMA zone: 2402 pages, LIFO batch:0
DMA32 zone: 16762 pages used for memmap
DMA32 zone: 763414 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled)
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x07] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 7, version 0, address 0xfec00000, GSI 0-0
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ERROR: Unable to locate IOAPIC for GSI 2
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ERROR: Unable to locate IOAPIC for GSI 9
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a701 base: 0xfed00000
SMP: Allowing 4 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 256
PM: Registered nosave memory: 000000000009d000 - 000000000009e000
PM: Registered nosave memory: 000000000009e000 - 0000000000100000
Allocating PCI resources starting at c0000000 (gap: c0000000:20000000)
Booting paravirtualized kernel on Xen
Xen version: 4.1-unstable (preserve-AD) (dom0)
NR_CPUS:16 nr_cpumask_bits:16 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 28 pages/cpu @ffff88000336d000 s83096 r8192 d23400 u114688
pcpu-alloc: s83096 r8192 d23400 u114688 alloc=28*4096
pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
trying to map vcpu_info 0 at ffff880003378020, mfn 13b378, offset 32
cpu 0 using vcpu_info at ffff880003378020
trying to map vcpu_info 1 at ffff880003394020, mfn 13b394, offset 32
cpu 1 using vcpu_info at ffff880003394020
trying to map vcpu_info 2 at ffff8800033b0020, mfn 13b3b0, offset 32
cpu 2 using vcpu_info at ffff8800033b0020
trying to map vcpu_info 3 at ffff8800033cc020, mfn 13b3cc, offset 32
cpu 3 using vcpu_info at ffff8800033cc020
Xen: using vcpu_info placement
Built 1 zonelists in Node order, mobility grouping on. Total pages: 765816
Policy zone: DMA32
Kernel command line: ro root=/dev/mapper/vg_lilith--raid-root LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us ignore_loglevel earlyprintk=xen console=hvc0 rdshell pcie_aspm=off
PCIe ASPM is disabled
PID hash table entries: 4096 (order: 3, 32768 bytes)
Initializing CPU#0
DMA: Placing 64MB software IO TLB between ffff88000794a000 - ffff88000b94a000
DMA: software IO TLB at phys 0x794a000 - 0xb94a000
xen_swiotlb_fixup: buf=ffff88000794a000 size=67108864
xen_swiotlb_fixup: buf=ffff88000b9aa000 size=32768
Memory: 2960308k/3137088k available (4691k kernel code, 396k absent, 176384k reserved, 2987k data, 656k init)
Hierarchical RCU implementation.
NR_IRQS:4352 nr_irqs:1280
xen: --> irq=0
xen: --> irq=1
xen: --> irq=2
xen: --> irq=3
xen: --> irq=4
xen: --> irq=5
xen: --> irq=6
xen: --> irq=7
xen: --> irq=8
xen: --> irq=9
xen: --> irq=10
xen: --> irq=11
xen: --> irq=12
xen: --> irq=13
xen: --> irq=14
xen: --> irq=15
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
xen: sci override: source_irq=9 global_irq=9 trigger=c polarity=1
xen: registering gsi 9 triggering 0 polarity 0
xen_allocate_pirq: returning irq 9 for gsi 9
xen: --> irq=9
xen: acpi sci 9
Console: colour VGA+ 80x25
console [hvc0] enabled, bootconsole disabled
console [hvc0] enabled, bootconsole disabled
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES: 8
... MAX_LOCK_DEPTH: 48
... MAX_LOCKDEP_KEYS: 8191
... CLASSHASH_SIZE: 4096
... MAX_LOCKDEP_ENTRIES: 16384
... MAX_LOCKDEP_CHAINS: 32768
... CHAINHASH_SIZE: 16384
memory used by lock dependency info: 5855 kB
per task-struct memory footprint: 1920 bytes
Xen: using vcpuop timer interface
installing Xen timer for CPU 0
alloc irq_desc for 1279 on node 0
alloc kstat_irqs on node 0
Detected 2400.062 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.12 BogoMIPS (lpj=2400062)
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 0/0x0 -> Node 0
CPU: Unsupported number of siblings 16
Performance Events: unsupported p6 CPU model 30 no PMU driver, software events only.
lockdep: fixing up alternatives.
SMP alternatives: switching to UP code
ACPI: Core revision 20090903
alloc irq_desc for 1278 on node 0
alloc kstat_irqs on node 0
cpu 0 spinlock event irq 1278
alloc irq_desc for 1277 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1276 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1275 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1274 on node 0
alloc kstat_irqs on node 0
installing Xen timer for CPU 1
alloc irq_desc for 1273 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1272 on node 0
alloc kstat_irqs on node 0
cpu 1 spinlock event irq 1272
lockdep: fixing up alternatives.
SMP alternatives: switching to SMP code
alloc irq_desc for 1271 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1270 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1269 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1268 on node 0
alloc kstat_irqs on node 0
Initializing CPU#1
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 1/0x0 -> Node 0
CPU: Unsupported number of siblings 16
installing Xen timer for CPU 2
alloc irq_desc for 1267 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1266 on node 0
alloc kstat_irqs on node 0
cpu 2 spinlock event irq 1266
alloc irq_desc for 1265 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1264 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1263 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1262 on node 0
alloc kstat_irqs on node 0
Initializing CPU#2
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 2/0x0 -> Node 0
CPU: Unsupported number of siblings 16
installing Xen timer for CPU 3
alloc irq_desc for 1261 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1260 on node 0
alloc kstat_irqs on node 0
cpu 3 spinlock event irq 1260
alloc irq_desc for 1259 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1258 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1257 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1256 on node 0
alloc kstat_irqs on node 0
Initializing CPU#3
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 3/0x0 -> Node 0
CPU: Unsupported number of siblings 16
Brought up 4 CPUs
Grant table initialized
Time: 16:45:17 Date: 04/07/10
NET: Registered protocol family 16
alloc irq_desc for 1255 on node 0
alloc kstat_irqs on node 0
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG at e0000000 - efffffff
PCI: Using configuration type 1 for base access
bio: create slab<bio-0> at 0
ERROR: Unable to locate IOAPIC for GSI 9
ACPI: EC: Look up EC in DSDT
ACPI Warning for \_SB_._OSC: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
\_SB_:_OSC evaluation returned wrong type
_OSC request data:1 6
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI Warning: Incorrect checksum in table [OEMB] - 91, should be 8E (20090903/tbutils-314)
ACPI Warning: Incorrect checksum in table [ ] - 7B, should be BF (20090903/tbutils-314)
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:1a.0: reg 10 32bit mmio: [0xfb3fc000-0xfb3fc3ff]
pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.5: PME# disabled
pci 0000:00:1d.0: reg 10 32bit mmio: [0xfb3fa000-0xfb3fa3ff]
pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.0: PME# disabled
pci 0000:00:1f.2: reg 10 io port: [0xb400-0xb407]
pci 0000:00:1f.2: reg 14 io port: [0xbc00-0xbc03]
pci 0000:00:1f.2: reg 18 io port: [0xb880-0xb887]
pci 0000:00:1f.2: reg 1c io port: [0xb800-0xb803]
pci 0000:00:1f.2: reg 20 io port: [0xb480-0xb49f]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xfb3f8000-0xfb3f87ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 10 64bit mmio: [0xfb3f6000-0xfb3f60ff]
pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
pci 0000:03:00.0: reg 10 32bit mmio: [0xfb420000-0xfb43ffff]
pci 0000:03:00.0: reg 14 32bit mmio: [0xfb480000-0xfb4fffff]
pci 0000:03:00.0: reg 18 io port: [0xcc00-0xcc1f]
pci 0000:03:00.0: reg 1c 32bit mmio: [0xfb41c000-0xfb41ffff]
pci 0000:03:00.0: reg 30 32bit mmio pref: [0xfb440000-0xfb47ffff]
pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
pci 0000:03:00.0: PME# disabled
pci 0000:00:1c.0: bridge io port: [0xc000-0xcfff]
pci 0000:00:1c.0: bridge 32bit mmio: [0xfb400000-0xfb4fffff]
pci 0000:04:00.0: reg 10 32bit mmio: [0xfb5e0000-0xfb5fffff]
pci 0000:04:00.0: reg 18 io port: [0xdc00-0xdc1f]
pci 0000:04:00.0: reg 1c 32bit mmio: [0xfb5dc000-0xfb5dffff]
pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
pci 0000:04:00.0: PME# disabled
pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff]
pci 0000:00:1c.4: bridge 32bit mmio: [0xfb500000-0xfb5fffff]
pci 0000:05:00.0: reg 10 32bit mmio: [0xfb6e0000-0xfb6fffff]
pci 0000:05:00.0: reg 18 io port: [0xec00-0xec1f]
pci 0000:05:00.0: reg 1c 32bit mmio: [0xfb6dc000-0xfb6dffff]
pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
pci 0000:05:00.0: PME# disabled
pci 0000:00:1c.5: bridge io port: [0xe000-0xefff]
pci 0000:00:1c.5: bridge 32bit mmio: [0xfb600000-0xfb6fffff]
pci 0000:06:03.0: reg 10 32bit mmio pref: [0xfa000000-0xfaffffff]
pci 0000:06:03.0: reg 14 32bit mmio: [0xfb7fc000-0xfb7fffff]
pci 0000:06:03.0: reg 18 32bit mmio: [0xfb800000-0xfbffffff]
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge 32bit mmio: [0xfb700000-0xfbffffff]
pci 0000:00:1e.0: bridge 64bit mmio pref: [0xfa000000-0xfaffffff]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR1E._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0ehci_hcd 0000:00:1a.0: port 1 high speed
ehci_hcd 0000:00:1a.0: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
ahci 0000:00:1f.2: version 3.0
xen: registering gsi 19 triggering 0 polarity 1
alloc irq_desc for 19 on node 0
alloc kstat_irqs on node 0
xen: --> irq=19
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
alloc irq_desc for 1247 on node 0
alloc kstat_irqs on node 0
ahci: SSS flag set, parallel bus scan disabled
ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems sxs apst
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8100 irq 1247
ata2: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8180 irq 1247
ata3: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8200 irq 1247
ata4: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8280 irq 1247
ata5: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8300 irq 1247
ata6: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8380 irq 1247
usb 1-1: udev 2, busnum 1, minor = 1
usb 1-1: New USB device found, idVendor=8087, idProduct=0020
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: usb_probe_device
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
hub 1-1:1.0: usb_probe_interface
hub 1-1:1.0: usb_probe_interface - got id
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 6 ports detected
hub 1-1:1.0: standalone hub
hub 1-1:1.0: individual port power switching
hub 1-1:1.0: individual port over-current protection
hub 1-1:1.0: Single TT
hub 1-1:1.0: TT requires at most 8 FS bit times (666 ns)
hub 1-1:1.0: Port indicators are supported
hub 1-1:1.0: power on to power good time: 100ms
hub 1-1:1.0: local power source is good
hub 1-1:1.0: enabling power on all ports
hub 2-0:1.0: state 7 ports 2 chg 0002 evt 0000
hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:1d.0: port 1 high speed
ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
hub 1-1:1.0: port 2: status 0101 change 0001
usb 2-1: new high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.0: port 1 high speed
ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 1-1: link qh256-0001/ffff8800bc51f9c0 start 1 [1/0 us]
usb 2-1: udev 2, busnum 2, minor = 129
usb 2-1: New USB device found, idVendor=8087, idProduct=0020
usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 2-1: usb_probe_device
usb 2-1: configuration #1 chosen from 1 choice
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
hub 2-1:1.0: usb_probe_interface
hub 2-1:1.0: usb_probe_interface - got id
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 8 ports detected
hub 2-1:1.0: standalone hub
hub 2-1:1.0: individual port power switching
hub 2-1:1.0: individual port over-current protection
hub 2-1:1.0: Single TT
hub 2-1:1.0: TT requires at most 8 FS bit times (666 ns)
hub 2-1:1.0: Port indicators are supported
hub 2-1:1.0: power on to power good time: 100ms
hub 2-1:1.0: local power source is good
hub 2-1:1.0: enabling power on all ports
hub 1-1:1.0: state 7 ports 6 chg 0004 evt 0000
hub 1-1:1.0: port 2, status 0101, change 0000, 12 Mb/s
hub 1-1:1.0: port 2 not reset yet, waiting 10ms
usb 1-1.2: new full speed USB device using ehci_hcd and address 3
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
hub 1-1:1.0: port 2 not reset yet, waiting 10ms
ata1.00: ATA-8: WDC WD10EADS-00P8B0, 01.00A01, max UDMA/133
ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA WDC WD10EADS-00P 01.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: Attached scsi generic sg0 type 0
sda:
usb 2-1: link qh256-0001/ffff8800bc51f6c0 start 1 [1/0 us]
sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
usb 1-1.2: skipped 1 descriptor after interface
usb 1-1.2: skipped 1 descriptor after interface
usb 1-1.2: default language 0x0409
usb 1-1.2: udev 3, busnum 1, minor = 2
usb 1-1.2: New USB device found, idVendor=0557, idProduct=2221
usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.2: Product: Hermon USB hidmouse Device
usb 1-1.2: Manufacturer: Winbond Electronics Corp
usb 1-1.2: usb_probe_device
usb 1-1.2: configuration #1 chosen from 1 choice
usb 1-1.2: adding 1-1.2:1.0 (config #1, interface 0)
usbhid 1-1.2:1.0: usb_probe_interface
usbhid 1-1.2:1.0: usb_probe_interface - got id
input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input4
generic-usb 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:1a.0-1.2/input0
usb 1-1.2: adding 1-1.2:1.1 (config #1, interface 1)
usbhid 1-1.2:1.1: usb_probe_interface
usbhid 1-1.2:1.1: usb_probe_interface - got id
input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.1/input/input5
usb 1-1.2: link qh8-0601/ffff8800be6225c0 start 2 [1/2 us]
generic-usb 0003:0557:2221.0002: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:1a.0-1.2/input1
hub 2-1:1.0: state 7 ports 8 chg 0000 evt 0000
hub 1-1:1.0: state 7 ports 6 chg 0000 evt 0004
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 sdb3 sdb4
sd 1:0:0:0: [sdb] Attached SCSI disk
input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input6
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-8: WDC WD10EADS-00P8B0, 01.00A01, max UDMA/133
ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
ata3.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA WDC WD10EADS-00P 01.0 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1 sdc2 sdc3 sdc4
sd 2:0:0:0: [sdc] Attached SCSI disk
hub 2-1:1.0: hub_suspend
usb 2-1: unlink qh256-0001/ffff8800bc51f6c0 start 1 [1/0 us]
usb 2-1: usb auto-suspend
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
ata4.00: configured for UDMA/133
scsi 3:0:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5
sd 3:0:0:0: [sdd] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
sd 3:0:0:0: Attached scsi generic sg3 type 0
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1 sdd2 sdd3 sdd4
sd 3:0:0:0: [sdd] Attached SCSI disk
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
md: raid10 personality registered for level 10
Intel AES-NI instructions are not detected.
md: md0 stopped.
md: bind<sdb3>
md: bind<sdc3>
md: bind<sdd3>
md: bind<sda3>
md: kicking non-fresh sdd3 from array!
md: unbind<sdd3>
md: export_rdev(sdd3)
md: kicking non-fresh sdb3 from array!
md: unbind<sdb3>
md: export_rdev(sdb3)
raid10: raid set md0 active with 2 out of 4 devices
md0: detected capacity change from 0 to 838860668928
md0: unknown partition table
hub 2-0:1.0: hub_suspend
usb usb2: bus auto-suspend
ehci_hcd 0000:00:1d.0: suspend root hub
Password:***********
EXT4-fs (dm-2): mounted filesystem with ordered data mode
type=1404 audit(1270658817.238:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
SELinux: 8192 avtab hash slots, 162639 rules.
SELinux: 8192 avtab hash slots, 162639 rules.
SELinux: 8 users, 12 roles, 3092 types, 152 bools, 1 sens, 1024 cats
SELinux: 77 classes, 162639 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-2, type ext4), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
type=1403 audit(1270658817.689:3): policy loaded auid=4294967295 ses=4294967295
Welcome to Fedora
Press 'I' to enter interactive startup.
Starting udev: udev: starting version 145
ACPI: SSDT 00000000bf7b0180 00F20 (v01 DpgPmm P001Ist 00000011 INTL 20051117)
ACPI: SSDT 00000000bf7b10a0 004D5 (v01 PmRef P001Cst 00003001 INTL 20051117)
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-2 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C2] C3[C3])
e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
e1000e: Copyright (c) 1999-2008 Intel Corporation.
xen: registering gsi 16 triggering 0 polarity 1
xen_allocate_pirq: returning irq 16 for gsi 16
xen: --> irq=16
Already setup the GSI :16
e1000e 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
e1000e 0000:03:00.0: setting latency timer to 64
alloc irq_desc for 1246 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1245 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1244 on node 0
alloc kstat_irqs on node 0
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-2 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C2] C3[C3])
0000:03:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1b:21:4f:65:6b
0000:03:00.0: eth0: Intel(R) PRO/1000 Network Connection
0000:03:00.0: eth0: MAC: 3, PHY: 8, PBA No: e46981-003
xen: registering gsi 16 triggering 0 polarity 1
xen_allocate_pirq: returning irq 16 for gsi 16
xen: --> irq=16
Already setup the GSI :16
e1000e 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
e1000e 0000:04:00.0: setting latency timer to 64
alloc irq_desc for 1243 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1242 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1241 on node 0
alloc kstat_irqs on node 0
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-2 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C2] C3[C3])
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-2 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C2] C3[C3])
0000:04:00.0: eth1: (PCI Express:2.5GB/s:Width x1) 00:30:48:dd:eb:66
0000:04:00.0: eth1: Intel(R) PRO/1000 Network Connection
0000:04:00.0: eth1: MAC: 3, PHY: 8, PBA No: 0101ff-0ff
xen: registering gsi 17 triggering 0 polarity 1
xen_allocate_pirq: returning irq 17 for gsi 17
xen: --> irq=17
Already setup the GSI :17
e1000e 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
e1000e 0000:05:00.0: setting latency timer to 64
alloc irq_desc for 1240 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1239 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 1238 on node 0
alloc kstat_irqs on node 0
0000:05:00.0: eth2: (PCI Express:2.5GB/s:Width x1) 00:30:48:dd:eb:67
0000:05:00.0: eth2: Intel(R) PRO/1000 Network Connection
0000:05:00.0: eth2: MAC: 3, PHY: 8, PBA No: 0101ff-0ff
udev: renamed network interface eth2 to eth1
udev: renamed network interface eth0 to eth2
udev: renamed network interface eth1_rename to eth0
mdadm: /dev/md0 is already in use.
Key slot 0 unlocked.
Key slot 0 unlocked.
device-mapper: multipath: version 1.1.0 loaded
Setting up Logical Volume Management: 14 logical volume(s) in volume group "vg_lilith-raid" now active
[ OK ]
Checking filesystems
Checking all file systems.
[/sbin/fsck.ext4 (1) -- /] fsck.ext4 -a /dev/mapper/vg_lilith--raid-root
/dev/mapper/vg_lilith--raid-root contains a file system with errors, check forced.
/dev/mapper/vg_lilith--raid-root: 343615/2564096 files (0.2% non-contiguous), 2390774/10240000 blocks
[/sbin/fsck.ext4 (1) -- /boot] fsck.ext4 -a /dev/sda2
[/sbin/fsck.ext4 (2) -- /boot-spare] fsck.ext4 -a /dev/sdb2
/dev/sdb2: clean, 11/66384 files, 12695/265072 blocks
/dev/sda2: clean, 89/66384 files, 69878/265072 blocks
[/sbin/fsck.ext4 (1) -- /home] fsck.ext4 -a /dev/mapper/luks-11eb0145-088a-4c13-acf4-9784e82bb1e3
/dev/mapper/luks-11eb0145-088a-4c13-acf4-9784e82bb1e3: clean, 506715/12804096 files, 10193956/51199495 blocks
[/sbin/fsck.ext4 (1) -- /var] fsck.ext4 -a /dev/mapper/luks-37e6b844-a112-427c-be60-ae6f4d9c5041
/dev/mapper/luks-37e6b844-a112-427c-be60-ae6f4d9c5041: clean, 21026/5120000 files, 490586/20479495 blocks
[ OK ]
Remounting root filesystem in read-write mode: [ OK ]
Mounting local filesystems: EXT4-fs (sda2): mounted filesystem with ordered data mode
SELinux: initialized (dev sda2, type ext4), uses xattr
EXT4-fs (sdb2): mounted filesystem with ordered data mode
SELinux: initialized (dev sdb2, type ext4), uses xattr
EXT4-fs (dm-15): mounted filesystem with ordered data mode
SELinux: initialized (dev dm-15, type ext4), uses xattr
EXT4-fs (dm-16): mounted filesystem with ordered data mode
SELinux: initialized (dev dm-16, type ext4), uses xattr
SELinux: initialized (dev xenfs, type xenfs), uses genfs_contexts
[ OK ]
Enabling local filesystem quotas: [ OK ]
Enabling /etc/fstab swaps: Adding 16381972k swap on /dev/mapper/luks-2aac27aa-0bb6-46cc-8a7a-83af1ca296a2. Priority:-1 extents:1 across:16381972k
[ OK ]
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
Entering non-interactive startup
Applying Intel CPU microcode update: platform microcode: firmware: requesting intel-ucode/06-1e-05
platform microcode: firmware: requesting intel-ucode/06-1e-05
platform microcode: firmware: requesting intel-ucode/06-1e-05
platform microcode: firmware: requesting intel-ucode/06-1e-05
Microcode Update Driver: v2.00<tigran@aivazian.fsnet.co.uk>, Peter Oruba
Microcode Update Driver: v2.00 removed.
Starting monitoring for VG vg_lilith-raid: 14 logical volume(s) in volume group "vg_lilith-raid" monitored
[ OK ]
ip6tables: Applying firewall rules: [ OK ]
ip6tables: Loading additional modules: nf_conntrack_netbios_ns [ OK ]
Starting auditd: [ OK ]
Starting portreserve: [ OK ]
Starting system logger: [ OK ]
Starting irqbalance: [ OK ]
Starting rpcbind: [ OK ]
Starting mdmonitor: [ OK ]
Starting system message bus: [ OK ]
Starting Avahi daemon... [ OK ]
Starting NFS statd: [ OK ]
Starting RPC idmapd: FATAL: Module sunrpc not found.
FATAL: Error running install command for sunrpc
Error: RPC MTAB does not exist.
Starting cups: [ OK ]
Starting acpi daemon: [ OK ]
Starting HAL daemon: [ OK ]
Starting PC/SC smart card daemon (pcscd): [ OK ]
Retrigger failed udev events[ OK ]
Setting network parameters... [ OK ]
Starting NetworkManager daemon: [ OK ]
Enabling Bluetooth devices:
Starting sshd: [ OK ]
ADDRCONF(NETDEV_UP): eth2: link is not ready
ntpdate: Synchronizing with time server: ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_UP): eth1: link is not ready
[FAILED]
Starting ntpd: [ OK ]
Starting abrt daemon: [ OK ]
usb 1-1.2: link qh8-0601/ffff8800b58ba740 start 3 [1/2 us]
[ OK ] crond: [ OK ]
Enabling monthly Smolt checkin: [ OK ]
[ OK ] atd: [ OK ]
Starting libvirtd daemon: [ OK ]
Bridge firewalling registered
virbr0: starting userspace STP failed, starting kernel STP
e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
e1000e: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
e1000e: eth0 NICMbps Full Duplex, Flow Control: RX/TX
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
Fedora release 12 (Constantine)
Kernel 2.6.32.11 on an x86_64 (/dev/hvc0)
lilith.goop.org login: usb usb2: usb auto-resume
ehci_hcd 0000:00:1d.0: resume root hub
hub 2-0:1.0: hub_resume
hub 2-0:1.0: port 1: status 0507 change 0000
usb 2-1: usb auto-resume
hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 2-1: finish resume
hub 2-1:1.0: hub_resume
ehci_hcd 0000:00:1d.0: reused qh ffff8800bc51f6c0 schedule
usb 2-1: link qh256-0001/ffff8800bc51f6c0 start 1 [1/0 us]
hub 2-1:1.0: state 7 ports
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: New DMAR errors in Xen 4.1
2010-04-07 16:55 ` Jeremy Fitzhardinge
@ 2010-04-08 2:32 ` Weidong Han
2010-04-08 16:58 ` Jeremy Fitzhardinge
0 siblings, 1 reply; 7+ messages in thread
From: Weidong Han @ 2010-04-08 2:32 UTC (permalink / raw)
To: Jeremy Fitzhardinge; +Cc: Xen-devel, Keir Fraser
Jeremy Fitzhardinge wrote:
> On 04/06/2010 07:50 PM, Weidong Han wrote:
>
>>> It turns out its... "Enable debug=y by default in the build." So I
>>> guess these errors have been happening silently thus far?
>>>
>>> J
>>>
>> I don't encounter this issue. These DMAR fault messages will be
>> printed even when debug=n. what platform are you using? could you post
>> complete booting log with "iommu=verbose"?
>>
>
> This is a Supermicro X8SIL-F system, which is a Lynnfield + Ibex Peak
> system.
>
> I've attached two boot logs below. The first is one where there lots of
> DMAR errors early, and the system is a disaster (basically doesn't come
> up, lots of devices fail to init). Unfortunately it looks like I
> mistyped "verbose".
>
> The second boot was immediately after the first and it comes up cleanly
> with no DMAR errors at all. So it appears there's some non-determinism
> there. The gmfns in the messages always appear to be about he same, so
> I wonder if it depends on exactly what pages the kernel ends up
> allocating for IO? (It probably also means my bisection results are
> suspect.)
>
the boot log with "iommu=verbose" looks fine. when you mistyped
"verbose", it equals to default iommu setting, that's iommu=1.
Can I understand that: the DMAR faults only occur when "debug=y" with
default iommu setting (iommu=1)?
Besides print more info, "iommu=verbose" also invokes
process_pending_softirqs in domain_context_mapping. Could you try below
patch to also call process_pending_softirqs for "iommu=1"?
diff -r 28e5409e3fb3 xen/drivers/passthrough/vtd/iommu.c
--- a/xen/drivers/passthrough/vtd/iommu.c Wed Apr 07 16:22:05 2010
+0100
+++ b/xen/drivers/passthrough/vtd/iommu.c Thu Apr 08 10:18:15 2010
+0800
@@ -1366,7 +1366,7 @@ static int domain_context_mapping(struct
break;
}
- if ( iommu_verbose )
+// if ( iommu_verbose )
process_pending_softirqs();
return ret;
> (BTW, what's a "type 9" E820 region?)
>
> Thanks,
> J
>
>
> __ __ _ _ _ _ _ _
> \ \/ /___ _ __ | || | / | _ _ _ __ ___| |_ __ _| |__ | | ___
> \ // _ \ '_ \ | || |_ | |__| | | | '_ \/ __| __/ _` | '_ \| |/ _ \
> / \ __/ | | | |__ _|| |__| |_| | | | \__ \ || (_| | |_) | | __/
> /_/\_\___|_| |_| |_|(_)_| \__,_|_| |_|___/\__\__,_|_.__/|_|\___|
>
> (XEN) Xen version 4.1-unstable (jeremy@) (gcc version 4.4.3 20100127 (Red Hat 4.4.3-4) (GCC) ) Tue Apr 6 17:23:29 PDT 2010
> (XEN) Latest ChangeSet: Tue Apr 06 17:23:12 2010 -0700 21115:ea6c67dc4577
> (XEN) Command line: com2=115200,8n1,0x3e8,5 console=com2,vga cpufreq=xen iommu=verbos8
> (XEN) Video information:
> (XEN) VGA is text mode 80x25, font 8x16
> (XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
> (XEN) EDID info not retrieved because no DDC retrieval method detected
> (XEN) Disc information:
> (XEN) Found 4 MBR signatures
> (XEN) Found 4 EDD information structures
> (XEN) Xen-e820 RAM map:
> (XEN) 0000000000000000 - 000000000009d800 (usable)
> (XEN) 000000000009d800 - 00000000000a0000 (reserved)
> (XEN) 00000000000e0000 - 0000000000100000 (reserved)
> (XEN) 0000000000100000 - 00000000bf790000 (usable)
> (XEN) 00000000bf79e000 - 00000000bf7a0000 type 9
> (XEN) 00000000bf7a0000 - 00000000bf7ae000 (ACPI data)
> (XEN) 00000000bf7ae000 - 00000000bf7d0000 (ACPI NVS)
> (XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved)
> (XEN) 00000000bf7ed000 - 00000000c0000000 (reserved)
> (XEN) 00000000e0000000 - 00000000f0000000 (reserved)
> (XEN) 00000000fed20000 - 00000000fed40000 (reserved)
> (XEN) 00000000fee00000 - 00000000fee01000 (reserved)
> (XEN) 0000000100000000 - 0000000140000000 (usable)
> (XEN) ACPI: RSDP 000FA110, 0024 (r2 ACPIAM)
> (XEN) ACPI: XSDT BF7A0100, 0084 (r1 SMCI 20100225 MSFT 97)
> (XEN) ACPI: FACP BF7A0290, 00F4 (r4 022510 FACP1918 20100225 MSFT 97)
> (XEN) ACPI: DSDT BF7A05F0, 6C55 (r2 10605 10605000 0 INTL 20051117)
> (XEN) ACPI: FACS BF7AE000, 0040
> (XEN) ACPI: APIC BF7A0390, 0092 (r2 022510 APIC1918 20100225 MSFT 97)
> (XEN) ACPI: MCFG BF7A0430, 003C (r1 022510 OEMMCFG 20100225 MSFT 97)
> (XEN) ACPI: OEMB BF7AE040, 0073 (r1 022510 OEMB1918 20100225 MSFT 97)
> (XEN) ACPI: HPET BF7AA5F0, 0038 (r1 022510 OEMHPET 20100225 MSFT 97)
> (XEN) ACPI: GSCI BF7AE0C0, 2024 (r1 022510 GMCHSCI 20100225 MSFT 97)
> (XEN) ACPI: DMAR BF7B00F0, 0090 (r1 AMI OEMDMAR 1 MSFT 97)
> (XEN) ACPI: SSDT BF7B1580, 0363 (r1 DpgPmm CpuPm 12 INTL 20051117)
> (XEN) ACPI: EINJ BF7AA630, 0130 (r1 AMIER AMI_EINJ 20100225 MSFT 97)
> (XEN) ACPI: BERT BF7AA7C0, 0030 (r1 AMIER AMI_BERT 20100225 MSFT 97)
> (XEN) ACPI: ERST BF7AA7F0, 01B0 (r1 AMIER AMI_ERST 20100225 MSFT 97)
> (XEN) ACPI: HEST BF7AA9A0, 00A8 (r1 AMIER ABC_HEST 20100225 MSFT 97)
> (XEN) System RAM: 4056MB (4153584kB)
> (XEN) No NUMA configuration found
> (XEN) Faking a node at 0000000000000000-0000000140000000
> (XEN) Domain heap initialised
> (XEN) found SMP MP-table at 000ff780
> (XEN) DMI present.
> (XEN) Using APIC driver default
> (XEN) ACPI: PM-Timer IO Port: 0x808
> (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0]
> (XEN) ACPI: wakeup_vec[bf7ae00c], vec_size[20]
> (XEN) ACPI: Local APIC address 0xfee00000
> (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> (XEN) Processor #0 7:14 APIC version 21
> (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
> (XEN) Processor #2 7:14 APIC version 21
> (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
> (XEN) Processor #4 7:14 APIC version 21
> (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
> (XEN) Processor #6 7:14 APIC version 21
> (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled)
> (XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled)
> (XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled)
> (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled)
> (XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
> (XEN) ACPI: IOAPIC (id[0x07] address[0xfec00000] gsi_base[0])
> (XEN) IOAPIC[0]: apic_id 7, version 32, address 0xfec00000, GSI 0-23
> (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> (XEN) ACPI: IRQ0 used by override.
> (XEN) ACPI: IRQ2 used by override.
> (XEN) ACPI: IRQ9 used by override.
> (XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
> (XEN) ACPI: HPET id: 0x8086a701 base: 0xfed00000
> (XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
> (XEN) PCI: MCFG area at e0000000 reserved in E820
> (XEN) Using ACPI (MADT) for SMP configuration information
> (XEN) Using scheduler: SMP Credit Scheduler (credit)
> (XEN) Detected 2400.067 MHz processor.
> (XEN) Initing memory sharing.
> (XEN) EPT support 2M super page.
> (XEN) VMX: Supported advanced features:
> (XEN) - APIC MMIO access virtualisation
> (XEN) - APIC TPR shadow
> (XEN) - Extended Page Tables (EPT)
> (XEN) - Virtual-Processor Identifiers (VPID)
> (XEN) - Virtual NMI
> (XEN) - MSR direct-access bitmap
> (XEN) HVM: ASIDs enabled.
> (XEN) HVM: VMX enabled
> (XEN) HVM: Hardware Assisted Paging detected.
> (XEN) Intel machine check reporting enabled
> (XEN) Intel VT-d Snoop Control supported.
> (XEN) Intel VT-d DMA Passthrough not supported.
> (XEN) Intel VT-d Queued Invalidation supported.
> (XEN) Intel VT-d Interrupt Remapping not supported.
> (XEN) I/O virtualisation enabled
> (XEN) I/O virtualisation for PV guests disabled
> (XEN) EPT support 2M super page.
> (XEN) EPT support 2M super page.
> (XEN) EPT support 2M super page.
> (XEN) Total of 4 processors activated.
> (XEN) ENABLING IO-APIC IRQs
> (XEN) -> Using new ACK method
> (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
> (XEN) TSC is reliable, synchronization unnecessary
> (XEN) Platform timer is 14.318MHz HPET
> �(XEN) Allocated console ring of 32 KiB.
> (XEN) microcode.c:73:d32767 microcode: CPU1 resumed
> (XEN) microcode.c:73:d32767 microcode: CPU2 resumed
> (XEN) Brought up 4 CPUs
> (XEN) microcode.c:73:d32767 microcode: CPU3 resumed
> (XEN) Turbo Mode detected!
> (XEN) HPET: 8 timers in total, 8 timers will be used for broadcast
> (XEN) ACPI sleep modes: S3
> (XEN) mcheck_poll: Machine check polling timer started.
> (XEN) *** LOADING DOMAIN 0 ***
> (XEN) elf_parse_binary: phdr: paddr=0x1000000 memsz=0x69c000
> (XEN) elf_parse_binary: phdr: paddr=0x169c000 memsz=0xe3cb0
> (XEN) elf_parse_binary: phdr: paddr=0x1780000 memsz=0x888
> (XEN) elf_parse_binary: phdr: paddr=0x1781000 memsz=0x14498
> (XEN) elf_parse_binary: phdr: paddr=0x1796000 memsz=0x9f5000
> (XEN) elf_parse_binary: memory: 0x1000000 -> 0x218b000
> (XEN) elf_xen_parse_note: GUEST_OS = "linux"
> (XEN) elf_xen_parse_note: GUEST_VERSION = "2.6"
> (XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0"
> (XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000
> (XEN) elf_xen_parse_note: ENTRY = 0xffffffff81796200
> (XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff81009000
> (XEN) elf_xen_parse_note: FEATURES = "!writable_page_tables|pae_pgdir_above_4gb"
> (XEN) elf_xen_parse_note: PAE_MODE = "yes"
> (XEN) elf_xen_parse_note: LOADER = "generic"
> (XEN) elf_xen_parse_note: unknown xen elf note (0xd)
> (XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1
> (XEN) elf_xen_parse_note: HV_START_LOW = 0xffff800000000000
> (XEN) elf_xen_parse_note: PADDR_OFFSET = 0x0
> (XEN) elf_xen_addr_calc_check: addresses:
> (XEN) virt_base = 0xffffffff80000000
> (XEN) elf_paddr_offset = 0x0
> (XEN) virt_offset = 0xffffffff80000000
> (XEN) virt_kstart = 0xffffffff81000000
> (XEN) virt_kend = 0xffffffff8218b000
> (XEN) virt_entry = 0xffffffff81796200
> (XEN) p2m_base = 0xffffffffffffffff
> (XEN) Xen kernel: 64-bit, lsb, compat32
> (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x218b000
> (XEN) PHYSICAL MEMORY ARRANGEMENT:
> (XEN) Dom0 alloc.: 0000000138000000->000000013c000000 (981633 pages to be allocated)
> (XEN) VIRTUAL MEMORY ARRANGEMENT:
> (XEN) Loaded kernel: ffffffff81000000->ffffffff8218b000
> (XEN) Init. ramdisk: ffffffff8218b000->ffffffff82b69800
> (XEN) Phys-Mach map: ffffffff82b6a000->ffffffff83307408
> (XEN) Start info: ffffffff83308000->ffffffff833084b4
> (XEN) Page tables: ffffffff83309000->ffffffff83326000
> (XEN) Boot stack: ffffffff83326000->ffffffff83327000
> (XEN) TOTAL: ffffffff80000000->ffffffff83400000
> (XEN) ENTRY ADDRESS: ffffffff81796200
> (XEN) Dom0 has maximum 4 VCPUs
> (XEN) elf_load_binary: phdr 0 at 0xffffffff81000000 -> 0xffffffff8169c000
> (XEN) elf_load_binary: phdr 1 at 0xffffffff8169c000 -> 0xffffffff8177fcb0
> (XEN) elf_load_binary: phdr 2 at 0xffffffff81780000 -> 0xffffffff81780888
> (XEN) elf_load_binary: phdr 3 at 0xffffffff81781000 -> 0xffffffff81795498
> (XEN) elf_load_binary: phdr 4 at 0xffffffff81796000 -> 0xffffffff81830000
> (XEN) Scrubbing Free RAM: .done.
> (XEN) Xen trace buffers: disabled
> (XEN) Std. Loglevel: All
> (XEN) Guest Loglevel: All
> (XEN) Xen is relinquishing VGA console.
> (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen)
> (XEN) Freed 164kB init memory.
> mapping kernel into physical memory
> Xen: setup ISA identity maps
> about to get started...
> Initializing cgroup subsys cpuset
> Initializing cgroup subsys cpu
> Linux version 2.6.32.11 (jeremy@lilith.goop.org) (gcc version 4.4.3 20100127 (Red Hat 4.4.3-4) (GCC) ) #7 SMP PREEMPT Mon Apr 5 14:58:54 PDT 2010
> Command line: ro root=/dev/mapper/vg_lilith--raid-root LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us ignore_loglevel earlyprintk=xen console=hvc0 rdshell pcie_aspm=off
> KERNEL supported cpus:
> Intel GenuineIntel
> AMD AuthenticAMD
> Centaur CentaurHauls
> xen_release_chunk: looking at area pfn bf790-bf79e: 14 pages freed
> xen_release_chunk: looking at area pfn bf7e0-bf7ed: 13 pages freed
> xen_release_chunk: looking at area pfn c0000-e0000: 131072 pages freed
> xen_release_chunk: looking at area pfn f0000-fec00: 14977 pages freed
> xen_release_chunk: looking at area pfn fec01-fed20: 0 pages freed
> xen_release_chunk: looking at area pfn fed40-fee00: 0 pages freed
> released 146076 pages of unused memory
> BIOS-provided physical RAM map:
> Xen: 0000000000000000 - 000000000009d800 (usable)
> Xen: 000000000009d800 - 0000000000100000 (reserved)
> Xen: 0000000000100000 - 00000000bf790000 (usable)
> Xen: 00000000bf79e000 - 00000000bf7a0000 type 9
> Xen: 00000000bf7a0000 - 00000000bf7ae000 (ACPI data)
> Xen: 00000000bf7ae000 - 00000000bf7d0000 (ACPI NVS)
> Xen: 00000000bf7d0000 - 00000000bf7e0000 (reserved)
> Xen: 00000000bf7ed000 - 00000000c0000000 (reserved)
> Xen: 00000000e0000000 - 00000000f0000000 (reserved)
> Xen: 00000000fec00000 - 00000000fec01000 (reserved)
> Xen: 00000000fed20000 - 00000000fed40000 (reserved)
> Xen: 00000000fee00000 - 00000000fee01000 (reserved)
> debug: ignoring loglevel setting.
> bootconsole [xenboot0] enabled
> DMI present.
> last_pfn = 0xbf790 max_arch_pfn = 0x400000000
> x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
> initial memory mapped : 0 - 20000000
> init_memory_mapping: 0000000000000000-00000000bf790000
> 0000000000 - 00bf790000 page 4k
> kernel direct mapping tables up to bf790000 @ 100000-700000
> RAMDISK: 0218b000 - 02b69800
> ACPI: RSDP 00000000000fa110 00024 (v02 ACPIAM)
> ACPI: XSDT 00000000bf7a0100 00084 (v01 SMCI 20100225 MSFT 00000097)
> ACPI: FACP 00000000bf7a0290 000F4 (v04 022510 FACP1918 20100225 MSFT 00000097)
> ACPI: DSDT 00000000bf7a05f0 06C55 (v02 10605 10605000 00000000 INTL 20051117)
> ACPI: FACS 00000000bf7ae000 00040
> ACPI: APIC 00000000bf7a0390 00092 (v02 022510 APIC1918 20100225 MSFT 00000097)
> ACPI: MCFG 00000000bf7a0430 0003C (v01 022510 OEMMCFG 20100225 MSFT 00000097)
> ACPI: OEMB 00000000bf7ae040 00073 (v01 022510 OEMB1918 20100225 MSFT 00000097)
> ACPI: HPET 00000000bf7aa5f0 00038 (v01 022510 OEMHPET 20100225 MSFT 00000097)
> ACPI: GSCI 00000000bf7ae0c0 02024 (v01 022510 GMCHSCI 20100225 MSFT 00000097)
> ACPI: 00000000bf7b00f0 00090 (v01 AMI OEMDMAR 00000001 MSFT 00000097)
> ACPI: SSDT 00000000bf7b1580 00363 (v01 DpgPmm CpuPm 00000012 INTL 20051117)
> ACPI: EINJ 00000000bf7aa630 00130 (v01 AMIER AMI_EINJ 20100225 MSFT 00000097)
> ACPI: BERT 00000000bf7aa7c0 00030 (v01 AMIER AMI_BERT 20100225 MSFT 00000097)
> ACPI: ERST 00000000bf7aa7f0 001B0 (v01 AMIER AMI_ERST 20100225 MSFT 00000097)
> ACPI: HEST 00000000bf7aa9a0 000A8 (v01 AMIER ABC_HEST 20100225 MSFT 00000097)
> ACPI: Local APIC address 0xfee00000
> No NUMA configuration found
> Faking a node at 0000000000000000-00000000bf790000
> Bootmem setup node 0 0000000000000000-00000000bf790000
> NODE_DATA [0000000000001000 - 0000000000005fff]
> bootmap [0000000000008000 - 000000000001fef7] pages 18
> (8 early reservations) ==> bootmem [0000000000 - 00bf790000]
> #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
> #1 [0003309000 - 0003326000] XEN PAGETABLES ==> [0003309000 - 0003326000]
> #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
> #3 [0001000000 - 000216a048] TEXT DATA BSS ==> [0001000000 - 000216a048]
> #4 [000218b000 - 0002b69800] RAMDISK ==> [000218b000 - 0002b69800]
> #5 [0002b6a000 - 0003309000] XEN START INFO ==> [0002b6a000 - 0003309000]
> #6 [000216b000 - 000216b21b] BRK ==> [000216b000 - 000216b21b]
> #7 [0000100000 - 00006e0000] PGTABLE ==> [0000100000 - 00006e0000]
> found SMP MP-table at [ffff8800000ff780] ff780
> Zone PFN ranges:
> DMA 0x00000000 -> 0x00001000
> DMA32 0x00001000 -> 0x00100000
> Normal 0x00100000 -> 0x00100000
> Movable zone start PFN for each node
> early_node_map[2] active PFN ranges
> 0: 0x00000000 -> 0x0000009d
> 0: 0x00000100 -> 0x000bf790
> On node 0 totalpages: 784173
> DMA zone: 88 pages used for memmap
> DMA zone: 1507 pages reserved
> DMA zone: 2402 pages, LIFO batch:0
> DMA32 zone: 16762 pages used for memmap
> DMA32 zone: 763414 pages, LIFO batch:31
> ACPI: PM-Timer IO Port: 0x808
> ACPI: Local APIC address 0xfee00000
> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
> ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
> ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
> ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled)
> ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled)
> ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled)
> ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled)
> ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
> ACPI: IOAPIC (id[0x07] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: apic_id 7, version 0, address 0xfec00000, GSI 0-0
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> ERROR: Unable to locate IOAPIC for GSI 2
> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> ERROR: Unable to locate IOAPIC for GSI 9
> Using ACPI (MADT) for SMP configuration information
> ACPI: HPET id: 0x8086a701 base: 0xfed00000
> SMP: Allowing 4 CPUs, 0 hotplug CPUs
> nr_irqs_gsi: 256
> PM: Registered nosave memory: 000000000009d000 - 000000000009e000
> PM: Registered nosave memory: 000000000009e000 - 0000000000100000
> Allocating PCI resources starting at c0000000 (gap: c0000000:20000000)
> Booting paravirtualized kernel on Xen
> Xen version: 4.1-unstable (preserve-AD) (dom0)
> NR_CPUS:16 nr_cpumask_bits:16 nr_cpu_ids:4 nr_node_ids:1
> PERCPU: Embedded 28 pages/cpu @ffff88000336d000 s83096 r8192 d23400 u114688
> pcpu-alloc: s83096 r8192 d23400 u114688 alloc=28*4096
> pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
> trying to map vcpu_info 0 at ffff880003378020, mfn 13b378, offset 32
> cpu 0 using vcpu_info at ffff880003378020
> trying to map vcpu_info 1 at ffff880003394020, mfn 13b394, offset 32
> cpu 1 using vcpu_info at ffff880003394020
> trying to map vcpu_info 2 at ffff8800033b0020, mfn 13b3b0, offset 32
> cpu 2 using vcpu_info at ffff8800033b0020
> trying to map vcpu_info 3 at ffff8800033cc020, mfn 13b3cc, offset 32
> cpu 3 using vcpu_info at ffff8800033cc020
> Xen: using vcpu_info placement
> Built 1 zonelists in Node order, mobility grouping on. Total pages: 765816
> Policy zone: DMA32
> Kernel command line: ro root=/dev/mapper/vg_lilith--raid-root LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us ignore_loglevel earlyprintk=xen console=hvc0 rdshell pcie_aspm=off
> PCIe ASPM is disabled
> PID hash table entries: 4096 (order: 3, 32768 bytes)
> Initializing CPU#0
> DMA: Placing 64MB software IO TLB between ffff88000794a000 - ffff88000b94a000
> DMA: software IO TLB at phys 0x794a000 - 0xb94a000
> xen_swiotlb_fixup: buf=ffff88000794a000 size=67108864
> xen_swiotlb_fixup: buf=ffff88000b9aa000 size=32768
> Memory: 2960308k/3137088k available (4691k kernel code, 396k absent, 176384k reserved, 2987k data, 656k init)
> Hierarchical RCU implementation.
> NR_IRQS:4352 nr_irqs:1280
> xen: --> irq=0
> xen: --> irq=1
> xen: --> irq=2
> xen: --> irq=3
> xen: --> irq=4
> xen: --> irq=5
> xen: --> irq=6
> xen: --> irq=7
> xen: --> irq=8
> xen: --> irq=9
> xen: --> irq=10
> xen: --> irq=11
> xen: --> irq=12
> xen: --> irq=13
> xen: --> irq=14
> xen: --> irq=15
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> xen: sci override: source_irq=9 global_irq=9 trigger=c polarity=1
> xen: registering gsi 9 triggering 0 polarity 0
> xen_allocate_pirq: returning irq 9 for gsi 9
> xen: --> irq=9
> xen: acpi sci 9
> Console: colour VGA+ 80x25
> console [hvc0] enabled, bootconsole disabled
> console [hvc0] enabled, bootconsole disabled
> Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
> ... MAX_LOCKDEP_SUBCLASSES: 8
> ... MAX_LOCK_DEPTH: 48
> ... MAX_LOCKDEP_KEYS: 8191
> ... CLASSHASH_SIZE: 4096
> ... MAX_LOCKDEP_ENTRIES: 16384
> ... MAX_LOCKDEP_CHAINS: 32768
> ... CHAINHASH_SIZE: 16384
> memory used by lock dependency info: 5855 kB
> per task-struct memory footprint: 1920 bytes
> Xen: using vcpuop timer interface
> installing Xen timer for CPU 0
> alloc irq_desc for 1279 on node 0
> alloc kstat_irqs on node 0
> Detected 2400.066 MHz processor.
> Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.13 BogoMIPS (lpj=2400066)
> Security Framework initialized
> SELinux: Initializing.
> SELinux: Starting in permissive mode
> Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
> Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
> Mount-cache hash table entries: 256
> Initializing cgroup subsys ns
> Initializing cgroup subsys cpuacct
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 256K
> CPU: L3 cache: 8192K
> CPU 0/0x0 -> Node 0
> CPU: Unsupported number of siblings 16
> Performance Events: unsupported p6 CPU model 30 no PMU driver, software events only.
> lockdep: fixing up alternatives.
> SMP alternatives: switching to UP code
> ACPI: Core revision 20090903
> alloc irq_desc for 1278 on node 0
> alloc kstat_irqs on node 0
> cpu 0 spinlock event irq 1278
> alloc irq_desc for 1277 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1276 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1275 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1274 on node 0
> alloc kstat_irqs on node 0
> installing Xen timer for CPU 1
> alloc irq_desc for 1273 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1272 on node 0
> alloc kstat_irqs on node 0
> cpu 1 spinlock event irq 1272
> lockdep: fixing up alternatives.
> SMP alternatives: switching to SMP code
> alloc irq_desc for 1271 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1270 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1269 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1268 on node 0
> alloc kstat_irqs on node 0
> Initializing CPU#1
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 256K
> CPU: L3 cache: 8192K
> CPU 1/0x0 -> Node 0
> CPU: Unsupported number of siblings 16
> installing Xen timer for CPU 2
> alloc irq_desc for 1267 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1266 on node 0
> alloc kstat_irqs on node 0
> cpu 2 spinlock event irq 1266
> alloc irq_desc for 1265 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1264 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1263 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1262 on node 0
> alloc kstat_irqs on node 0
> Initializing CPU#2
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 256K
> CPU: L3 cache: 8192K
> CPU 2/0x0 -> Node 0
> CPU: Unsupported number of siblings 16
> installing Xen timer for CPU 3
> alloc irq_desc for 1261 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1260 on node 0
> alloc kstat_irqs on node 0
> cpu 3 spinlock event irq 1260
> alloc irq_desc for 1259 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1258 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1257 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1256 on node 0
> alloc kstat_irqs on node 0
> Initializing CPU#3
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 256K
> CPU: L3 cache: 8192K
> CPU 3/0x0 -> Node 0
> CPU: Unsupported number of siblings 16
> Brought up 4 CPUs
> Grant table initialized
> Time: 16:42:50 Date: 04/07/10
> NET: Registered protocol family 16
> alloc irq_desc for 1255 on node 0
> alloc kstat_irqs on node 0
> ACPI: bus type pci registered
> PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
> PCI: MCFG area at e0000000 reserved in E820
> PCI: Using MMCONFIG at e0000000 - efffffff
> PCI: Using configuration type 1 for base access
> bio: create slab<bio-0> at 0
> ERROR: Unable to locate IOAPIC for GSI 9
> ACPI: EC: Look up EC in DSDT
> ACPI Warning for \_SB_._OSC: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
> \_SB_:_OSC evaluation returned wrong type
> _OSC request data:1 6
> ACPI: Executed 1 blocks of module-level executable AML code
> ACPI: Interpreter enabled
> ACPI: (supports S0 S1 S4 S5)
> ACPI: Using IOAPIC for interrupt routing
> ACPI Warning: Incorrect checksum in table [OEMB] - 91, should be 8E (20090903/tbutils-314)
> ACPI Warning: Incorrect checksum in table [ ] - 7B, should be BF (20090903/tbutils-314)
> ACPI: No dock devices found.
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
> pci 0000:00:03.0: PME# disabled
> pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
> pci 0000:00:05.0: PME# disabled
> pci 0000:00:1a.0: reg 10 32bit mmio: [0xfb3fc000-0xfb3fc3ff]
> pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
> pci 0000:00:1a.0: PME# disabled
> pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
> pci 0000:00:1c.0: PME# disabled
> pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
> pci 0000:00:1c.4: PME# disabled
> pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
> pci 0000:00:1c.5: PME# disabled
> pci 0000:00:1d.0: reg 10 32bit mmio: [0xfb3fa000-0xfb3fa3ff]
> pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
> pci 0000:00:1d.0: PME# disabled
> pci 0000:00:1f.2: reg 10 io port: [0xb400-0xb407]
> pci 0000:00:1f.2: reg 14 io port: [0xbc00-0xbc03]
> pci 0000:00:1f.2: reg 18 io port: [0xb880-0xb887]
> pci 0000:00:1f.2: reg 1c io port: [0xb800-0xb803]
> pci 0000:00:1f.2: reg 20 io port: [0xb480-0xb49f]
> pci 0000:00:1f.2: reg 24 32bit mmio: [0xfb3f8000-0xfb3f87ff]
> pci 0000:00:1f.2: PME# supported from D3hot
> pci 0000:00:1f.2: PME# disabled
> pci 0000:00:1f.3: reg 10 64bit mmio: [0xfb3f6000-0xfb3f60ff]
> pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
> pci 0000:03:00.0: reg 10 32bit mmio: [0xfb420000-0xfb43ffff]
> pci 0000:03:00.0: reg 14 32bit mmio: [0xfb480000-0xfb4fffff]
> pci 0000:03:00.0: reg 18 io port: [0xcc00-0xcc1f]
> pci 0000:03:00.0: reg 1c 32bit mmio: [0xfb41c000-0xfb41ffff]
> pci 0000:03:00.0: reg 30 32bit mmio pref: [0xfb440000-0xfb47ffff]
> pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
> pci 0000:03:00.0: PME# disabled
> pci 0000:00:1c.0: bridge io port: [0xc000-0xcfff]
> pci 0000:00:1c.0: bridge 32bit mmio: [0xfb400000-0xfb4fffff]
> pci 0000:04:00.0: reg 10 32bit mmio: [0xfb5e0000-0xfb5fffff]
> pci 0000:04:00.0: reg 18 io port: [0xdc00-0xdc1f]
> pci 0000:04:00.0: reg 1c 32bit mmio: [0xfb5dc000-0xfb5dffff]
> pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
> pci 0000:04:00.0: PME# disabled
> pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff]
> pci 0000:00:1c.4: bridge 32bit mmio: [0xfb500000-0xfb5fffff]
> pci 0000:05:00.0: reg 10 32bit mmio: [0xfb6e0000-0xfb6fffff]
> pci 0000:05:00.0: reg 18 io port: [0xec00-0xec1f]
> pci 0000:05:00.0: reg 1c 32bit mmio: [0xfb6dc000-0xfb6dffff]
> pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
> pci 0000:05:00.0: PME# disabled
> pci 0000:00:1c.5: bridge io port: [0xe000-0xefff]
> pci 0000:00:1c.5: bridge 32bit mmio: [0xfb600000-0xfb6fffff]
> pci 0000:06:03.0: reg 10 32bit mmio pref: [0xfa000000-0xfaffffff]
> pci 0000:06:03.0: reg 14 32bit mmio: [0xfb7fc000-0xfb7fffff]
> pci 0000:06:03.0: reg 18 32bit mmio: [0xfb800000-0xfbffffff]
> pci 0000:00:1e.0: transparent bridge
> pci 0000:00:1e.0: bridge 32bit mmio: [0xfb700000-0xfbffffff]
> pci 0000:00:1e.0: bridge 64bit mmio pref: [0xfa000000-0xfaffffff]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR1E._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR20._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR24._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR25._PRT]
> (XEN) PCI add device 00:00.0
> (XEN) PCI add device 00:03.0
> (XEN) PCI add device 00:05.0
> (XEN) PCI add device 00:08.0
> (XEN) PCI add device 00:08.1
> (XEN) PCI add device 00:08.2
> (XEN) PCI add device 00:08.3
> (XEN) PCI add device 00:10.0
> (XEN) PCI add device 00:10.1
> (XEN) PCI add device 00:1a.0
> (XEN) PCI add device 00:1c.0
> (XEN) PCI add device 00:1c.4
> (XEN) PCI add device 00:1c.5
> (XEN) PCI add device 00:1d.0
> (XEN) PCI add device 00:1e.0
> (XEN) PCI add device 00:1f.0
> (XEN) PCI add device 00:1f.2
> (XEN) PCI add device 00:1f.3
> (XEN) PCI add device 03:00.0
> (XEN) PCI add device 04:00.0
> (XEN) PCI add device 05:00.0
> (XEN) PCI add device 06:03.0
> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12 *14 15)
> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled.
> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 *7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled.
> ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 6 7 10 11 12 14 *15)
> sync cpu 0 get result 1 max_id 3
> sync cpu 1 get result 1 max_id 3
> sync cpu 2 get result 1 max_id 3
> sync cpu 3 get result 1 max_id 3
> alloc irq_desc for 1254 on node 0
> alloc kstat_irqs on node 0
> xen_balloon: Initialising balloon driver with page order 0.
> vgaarb: device added: PCI:0000:06:03.0,decodes=io+mem,owns=io+mem,locks=none
> vgaarb: loaded
> SCSI subsystem initialized
> libata version 3.00 loaded.
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> PCI: Using ACPI for IRQ routing
> NetLabel: Initializing
> NetLabel: domain hash size = 128
> NetLabel: protocols = UNLABELED CIPSOv4
> NetLabel: unlabeled traffic allowed by default
> Switching to clocksource xen
> pnp: PnP ACPI init
> ACPI: bus type pnp registered
> xen: registering gsi 8 triggering 1 polarity 0
> xen_allocate_pirq: returning irq 8 for gsi 8
> xen:scsi0 : ahci
> scsi1 : ahci
> scsi2 : ahci
> scsi3 : ahci
> scsi4 : ahci
> scsi5 : ahci
> ata1: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8100 irq 1247
> ata2: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8180 irq 1247
> ata3: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8200 irq 1247
> ata4: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8280 irq 1247
> ata5: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8300 irq 1247
> ata6: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8380 irq 1247
> usb 1-1: udev 2, busnum 1, minor = 1
> usb 1-1: New USB device found, idVendor=8087, idProduct=0020
> usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
> usb 1-1: usb_probe_device
> usb 1-1: configuration #1 chosen from 1 choice
> usb 1-1: adding 1-1:1.0 (config #1, interface 0)
> hub 1-1:1.0: usb_probe_interface
> hub 1-1:1.0: usb_probe_interface - got id
> hub 1-1:1.0: USB hub found
> hub 1-1:1.0: 6 ports detected
> hub 1-1:1.0: standalone hub
> hub 1-1:1.0: individual port power switching
> hub 1-1:1.0: individual port over-current protection
> hub 1-1:1.0: Single TT
> hub 1-1:1.0: TT requires at most 8 FS bit times (666 ns)
> hub 1-1:1.0: Port indicators are supported
> hub 1-1:1.0: power on to power good time: 100ms
> hub 1-1:1.0: local power source is good
> hub 1-1:1.0: enabling power on all ports
> hub 2-0:1.0: state 7 ports 2 chg 0002 evt 0000
> hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
> ehci_hcd 0000:00:1d.0: port 1 high speed
> ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> hub 1-1:1.0: port 2: status 0101 change 0001
> usb 2-1: new high speed USB device using ehci_hcd and address 2
> ehci_hcd 0000:00:1d.0: port 1 high speed
> ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> usb 1-1: link qh256-0001/ffff8800bcd9ab40 start 1 [1/0 us]
> usb 2-1: udev 2, busnum 2, minor = 129
> usb 2-1: New USB device found, idVendor=8087, idProduct=0020
> usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
> usb 2-1: usb_probe_device
> usb 2-1: configuration #1 chosen from 1 choice
> usb 2-1: adding 2-1:1.0 (config #1, interface 0)
> hub 2-1:1.0: usb_probe_interface
> hub 2-1:1.0: usb_probe_interface - got id
> hub 2-1:1.0: USB hub found
> hub 2-1:1.0: 8 ports detected
> hub 2-1:1.0: standalone hub
> hub 2-1:1.0: individual port power switching
> hub 2-1:1.0: individual port over-current protection
> hub 2-1:1.0: Single TT
> hub 2-1:1.0: TT requires at most 8 FS bit times (666 ns)
> hub 2-1:1.0: Port indicators are supported
> hub 2-1:1.0: power on to power good time: 100ms
> hub 2-1:1.0: local power source is good
> hub 2-1:1.0: enabling power on all ports
> hub 1-1:1.0: state 7 ports 6 chg 0004 evt 0000
> hub 1-1:1.0: port 2, status 0101, change 0000, 12 Mb/s
> usb 1-1.2: new full speed USB device using ehci_hcd and address 3
> hub 1-1:1.0: port 2 not reset yet, waiting 10ms
> ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata1.00: ATA-8: WDC WD10EADS-00P8B0, 01.00A01, max UDMA/133
> ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
> ata1.00: configured for UDMA/133
> scsi 0:0:0:0: Direct-Access ATA WDC WD10EADS-00P 01.0 PQ: 0 ANSI: 5
> sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sd 0:0:0:0: Attached scsi generic sg0 type 0
> sda:
> usb 2-1: link qh256-0001/ffff8800be450cc0 start 1 [1/0 us]
> sda1 sda2 sda3 sda4
> sd 0:0:0:0: [sda] Attached SCSI disk
> usb 1-1.2: skipped 1 descriptor after interface
> usb 1-1.2: skipped 1 descriptor after interface
> usb 1-1.2: default language 0x0409
> usb 1-1.2: udev 3, busnum 1, minor = 2
> usb 1-1.2: New USB device found, idVendor=0557, idProduct=2221
> usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
> usb 1-1.2: Product: Hermon USB hidmouse Device
> usb 1-1.2: Manufacturer: Winbond Electronics Corp
> usb 1-1.2: usb_probe_device
> usb 1-1.2: configuration #1 chosen from 1 choice
> usb 1-1.2: adding 1-1.2:1.0 (config #1, interface 0)
> usbhid 1-1.2:1.0: usb_probe_interface
> usbhid 1-1.2:1.0: usb_probe_interface - got id
> input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input4
> generic-usb 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:1a.0-1.2/input0
> usb 1-1.2: adding 1-1.2:1.1 (config #1, interface 1)
> usbhid 1-1.2:1.1: usb_probe_interface
> usbhid 1-1.2:1.1: usb_probe_interface - got id
> input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.1/input/input5
> usb 1-1.2: link qh8-0601/ffff8800bc52e440 start 2 [1/2 us]
> generic-usb 0003:0557:2221.0002: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:1a.0-1.2/input1
> hub 2-1:1.0: state 7 ports 8 chg 0000 evt 0000
> hub 1-1:1.0: state 7 ports 6 chg 0000 evt 0004
> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata2.00: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
> ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
> ata2.00: configured for UDMA/133
> scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5
> sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
> sd 1:0:0:0: Attached scsi generic sg1 type 0
> sd 1:0:0:0: [sdb] Write Protect is off
> sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sdb: sdb1 sdb2 sdb3 sdb4
> sd 1:0:0:0: [sdb] Attached SCSI disk
> input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input6
> ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata3.00: ATA-8: WDC WD10EADS-00P8B0, 01.00A01, max UDMA/133
> ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
> ata3.00: configured for UDMA/133
> scsi 2:0:0:0: Direct-Access ATA WDC WD10EADS-00P 01.0 PQ: 0 ANSI: 5
> sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
> sd 2:0:0:0: Attached scsi generic sg2 type 0
> sd 2:0:0:0: [sdc] Write Protect is off
> sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
> sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sdc: sdc1 sdc2 sdc3 sdc4
> sd 2:0:0:0: [sdc] Attached SCSI disk
> hub 2-1:1.0: hub_suspend
> usb 2-1: unlink qh256-0001/ffff8800be450cc0 start 1 [1/0 us]
> usb 2-1: usb auto-suspend
> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata4.00: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
> ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
> ata4.00: configured for UDMA/133
> scsi 3:0:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5
> sd 3:0:0:0: [sdd] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
> sd 3:0:0:0: Attached scsi generic sg3 type 0
> sd 3:0:0:0: [sdd] Write Protect is off
> sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
> sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sdd: sdd1 sdd2 sdd3 sdd4
> sd 3:0:0:0: [sdd] Attached SCSI disk
> ata5: SATA link down (SStatus 0 SControl 300)
> ata6: SATA link down (SStatus 0 SControl 300)
> md: raid10 personality registered for level 10
> Intel AES-NI instructions are not detected.
> md: md0 stopped.
> md: bind<sdb3>
> md: bind<sdc3>
> md: bind<sdd3>
> md: bind<sda3>
> raid10: md0 is not clean -- starting background reconstruction
> raid10: raid set md0 active with 4 out of 4 devices
> md0: detected capacity change from 0 to 838860668928
> md: resync of RAID array md0
> md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
> md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
> md: using 128k window, over a total of 819199872 blocks.
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf579000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf579
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 179
> (XEN) l1[179] = 0
> (XEN) l1[179] not present
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf579000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf579
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 179
> (XEN) l1[179] = 0
> (XEN) l1[179] not present
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 178
> (XEN) l1[178] = 0
> (XEN) l1[178] not present
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 178
> (XEN) l1[178] = 0
> (XEN) l1[178] not present
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 17b
> (XEN) l1[17b] = 0
> (XEN) l1[17b] not present
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 17b
> (XEN) l1[17b] = 0
> (XEN) l1[17b] not present
> md0:(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 17b
> (XEN) l1[17b] = 0
> (XEN) l1[17b] not present
>
> ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
> ata2.00: irq_stat 0x20000000, host bus error
> ata2: SError: { HostInt }
> ata2.00: failed command: WRITE FPDMA QUEUED
> ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
> res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata2.00: status: { DRDY }
> ata2: hard resetting link
> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata2.00: configured for UDMA/133
> ata2: EH complete
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 17b
> (XEN) l1[17b] = 0
> (XEN) l1[17b] not present
> ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
> ata2.00: irq_stat 0x20000000, host bus error
> ata2: SError: { HostInt }
> ata2.00: failed command: WRITE FPDMA QUEUED
> ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
> res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata2.00: status: { DRDY }
> ata2: hard resetting link
> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata2.00: configured for UDMA/133
> ata2: EH complete
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 17b
> (XEN) l1[17b] = 0
> (XEN) l1[17b] not present
> ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
> ata2.00: irq_stat 0x20000000, host bus error
> ata2: SError: { HostInt }
> ata2.00: failed command: WRITE FPDMA QUEUED
> ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
> res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata2.00: status: { DRDY }
> ata2: hard resetting link
> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata2.00: configured for UDMA/133
> ata2: EH complete
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 17b
> (XEN) l1[17b] = 0
> (XEN) l1[17b] not present
> ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
> ata2.00: irq_stat 0x20000000, host bus error
> ata2: SError: { HostInt }
> ata2.00: failed command: WRITE FPDMA QUEUED
> ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
> res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata2.00: status: { DRDY }
> ata2: hard resetting link
> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata2.00: configured for UDMA/133
> ata2: EH complete
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 17b
> (XEN) l1[17b] = 0
> (XEN) l1[17b] not present
> ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
> ata2.00: irq_stat 0x20000000, host bus error
> ata2: SError: { HostInt }
> ata2.00: failed command: WRITE FPDMA QUEUED
> ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
> res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata2.00: status: { DRDY }
> ata2: hard resetting link
> hub 2-0:1.0: hub_suspend
> usb usb2: bus auto-suspend
> ehci_hcd 0000:00:1d.0: suspend root hub
> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata2.00: configured for UDMA/133
> ata2: EH complete
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 17b
> (XEN) l1[17b] = 0
> (XEN) l1[17b] not present
> ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
> ata2.00: irq_stat 0x20000000, host bus error
> ata2: SError: { HostInt }
> ata2.00: failed command: WRITE FPDMA QUEUED
> ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
> res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata2.00: status: { DRDY }
> ata2: hard resetting link
> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata2.00: configured for UDMA/133
> sd 1:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
> sd 1:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor]
> Descriptor sense data with sense descriptors (in hex):
> 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
> 0c a0 aa c3
> sd 1:0:0:0: [sdb] Add. Sense: No additional sense information
> sd 1:0:0:0: [sdb] CDB: Write(10): 2a 00 0c a0 aa c3 00 00 80 00
> end_request: I/O error, dev sdb, sector 211856067
> raid10: Disk failure on sdb3, disabling device.
> raid10: Operation continuing on 3 devices.
> ata2: EH complete
> unknown partition table
> md: md0: resync done.
> md: checkpointing resync of md0.
> RAID10 conf printout:
> --- wd:3 rd:4
> disk 0, wo:0, o:1, dev:sda3
> disk 1, wo:1, o:0, dev:sdb3
> disk 2, wo:0, o:1, dev:sdc3
> disk 3, wo:0, o:1, dev:sdd3
> RAID10 conf printout:
> --- wd:3 rd:4
> disk 0, wo:0, o:1, dev:sda3
> disk 2, wo:0, o:1, dev:sdc3
> disk 3, wo:0, o:1, dev:sdd3
> md: resync of RAID array md0
> md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
> md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
> md: using 128k window, over a total of 819199872 blocks.
> md: resuming resync of md0 from checkpoint.
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 178
> (XEN) l1[178] = 0
> (XEN) l1[178] not present
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf579000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf579
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 179
> (XEN) l1[179] = 0
> (XEN) l1[179] not present
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 17b
> (XEN) l1[17b] = 0
> (XEN) l1[17b] not present
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 17b
> (XEN) l1[17b] = 0
> (XEN) l1[17b] not present
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf57b000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf57b
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 17b
> (XEN) l1[17b] = 0
> (XEN) l1[17b] not present
> ata4.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
> ata4.00: irq_stat 0x20000000, host bus error
> ata4: SError: { HostInt }
> ata4.00: failed command: WRITE FPDMA QUEUED
> ata4.00: cmd 61/80:00:43:b2:a1/00:00:0c:00:00/40 tag 0 ncq 65536 out
> res 40/00:04:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4: hard resetting link
> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata4.00: configured for UDMA/133
> ata4: EH complete
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 178
> (XEN) l1[178] = 0
> (XEN) l1[178] not present
> ata4.00: exception Emask 0x60 SAct 0x3 SErr 0x800 action 0x6 frozen
> ata4.00: irq_stat 0x20000000, host bus error
> ata4: SError: { HostInt }
> ata4.00: failed command: WRITE FPDMA QUEUED
> ata4.00: cmd 61/80:00:43:b2:a1/00:00:0c:00:00/40 tag 0 ncq 65536 out
> res 40/00:0c:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: WRITE FPDMA QUEUED
> ata4.00: cmd 61/80:08:43:b1:a1/00:00:0c:00:00/40 tag 1 ncq 65536 out
> res 40/00:0c:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4: hard resetting link
> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata4.00: configured for UDMA/133
> ata4: EH complete
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 178
> (XEN) l1[178] = 0
> (XEN) l1[178] not present
> ata4.00: exception Emask 0x60 SAct 0x3 SErr 0x800 action 0x6 frozen
> ata4.00: irq_stat 0x20000000, host bus error
> ata4: SError: { HostInt }
> ata4.00: failed command: WRITE FPDMA QUEUED
> ata4.00: cmd 61/80:00:43:b1:a1/00:00:0c:00:00/40 tag 0 ncq 65536 out
> res 40/00:0c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: WRITE FPDMA QUEUED
> ata4.00: cmd 61/80:08:43:b2:a1/00:00:0c:00:00/40 tag 1 ncq 65536 out
> res 40/00:0c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4: hard resetting link
> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata4.00: configured for UDMA/133
> ata4: EH complete
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 178
> (XEN) l1[178] = 0
> (XEN) l1[178] not present
> ata4.00: exception Emask 0x60 SAct 0x3f SErr 0x800 action 0x6 frozen
> ata4.00: irq_stat 0x20000000, host bus error
> ata4: SError: { HostInt }
> ata4.00: failed command: WRITE FPDMA QUEUED
> ata4.00: cmd 61/80:00:43:b2:a1/00:00:0c:00:00/40 tag 0 ncq 65536 out
> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: WRITE FPDMA QUEUED
> ata4.00: cmd 61/80:08:43:b1:a1/00:00:0c:00:00/40 tag 1 ncq 65536 out
> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: READ FPDMA QUEUED
> ata4.00: cmd 60/00:10:43:2d:a2/04:00:0c:00:00/40 tag 2 ncq 524288 in
> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: READ FPDMA QUEUED
> ata4.00: cmd 60/00:18:43:31:a2/04:00:0c:00:00/40 tag 3 ncq 524288 in
> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: READ FPDMA QUEUED
> ata4.00: cmd 60/00:20:43:35:a2/04:00:0c:00:00/40 tag 4 ncq 524288 in
> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: READ FPDMA QUEUED
> ata4.00: cmd 60/00:28:43:39:a2/04:00:0c:00:00/40 tag 5 ncq 524288 in
> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4: hard resetting link
> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata4.00: configured for UDMA/133
> ata4: EH complete
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 178
> (XEN) l1[178] = 0
> (XEN) l1[178] not present
> ata4.00: exception Emask 0x60 SAct 0x3f SErr 0x800 action 0x6 frozen
> ata4.00: irq_stat 0x20000000, host bus error
> ata4: SError: { HostInt }
> ata4.00: failed command: READ FPDMA QUEUED
> ata4.00: cmd 60/00:00:43:39:a2/04:00:0c:00:00/40 tag 0 ncq 524288 in
> res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: READ FPDMA QUEUED
> ata4.00: cmd 60/00:08:43:35:a2/04:00:0c:00:00/40 tag 1 ncq 524288 in
> res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: READ FPDMA QUEUED
> ata4.00: cmd 60/00:10:43:31:a2/04:00:0c:00:00/40 tag 2 ncq 524288 in
> res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: READ FPDMA QUEUED
> ata4.00: cmd 60/00:18:43:2d:a2/04:00:0c:00:00/40 tag 3 ncq 524288 in
> res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: WRITE FPDMA QUEUED
> ata4.00: cmd 61/80:20:43:b1:a1/00:00:0c:00:00/40 tag 4 ncq 65536 out
> res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: WRITE FPDMA QUEUED
> ata4.00: cmd 61/80:28:43:b2:a1/00:00:0c:00:00/40 tag 5 ncq 65536 out
> res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4: hard resetting link
> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata4.00: configured for UDMA/133
> ata4: EH complete
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 178
> (XEN) l1[178] = 0
> (XEN) l1[178] not present
> ata4.00: exception Emask 0x60 SAct 0x3f SErr 0x800 action 0x6 frozen
> ata4.00: irq_stat 0x20000000, host bus error
> ata4: SError: { HostInt }
> ata4.00: failed command: WRITE FPDMA QUEUED
> ata4.00: cmd 61/80:00:43:b2:a1/00:00:0c:00:00/40 tag 0 ncq 65536 out
> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: WRITE FPDMA QUEUED
> ata4.00: cmd 61/80:08:43:b1:a1/00:00:0c:00:00/40 tag 1 ncq 65536 out
> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: READ FPDMA QUEUED
> ata4.00: cmd 60/00:10:43:2d:a2/04:00:0c:00:00/40 tag 2 ncq 524288 in
> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: READ FPDMA QUEUED
> ata4.00: cmd 60/00:18:43:31:a2/04:00:0c:00:00/40 tag 3 ncq 524288 in
> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: READ FPDMA QUEUED
> ata4.00: cmd 60/00:20:43:35:a2/04:00:0c:00:00/40 tag 4 ncq 524288 in
> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: READ FPDMA QUEUED
> ata4.00: cmd 60/00:28:43:39:a2/04:00:0c:00:00/40 tag 5 ncq 524288 in
> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4: hard resetting link
> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata4.00: configured for UDMA/133
> sd 3:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
> sd 3:0:0:0: [sdd] Sense Key : Aborted Command [current] [descriptor]
> Descriptor sense data with sense descriptors (in hex):
> 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
> 0c a2 39 43
> sd 3:0:0:0: [sdd] Add. Sense: No additional sense information
> sd 3:0:0:0: [sdd] CDB: Write(10): 2a 00 0c a1 b2 43 00 00 80 00
> end_request: I/O error, dev sdd, sector 211923523
> raid10: Disk failure on sdd3, disabling device.
> raid10: Operation continuing on 2 devices.
> ata4: EH complete
> md: md0: resync done.
> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2] fault addr bf578000, iommu reg = ffff82c3fff57000
> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn = bf578
> (XEN) root_entry = ffff83013ff36000
> (XEN) root_entry[0] = 13c6bb001
> (XEN) context = ffff83013c6bb000
> (XEN) context[fa] = 2_13fec4001
> (XEN) l4 = ffff83013fec4000
> (XEN) l4_index = 0
> (XEN) l4[0] = 13fec1003
> (XEN) l3 = ffff83013fec1000
> (XEN) l3_index = 2
> (XEN) l3[2] = 13ccbe003
> (XEN) l2 = ffff83013ccbe000
> (XEN) l2_index = 1fa
> (XEN) l2[1fa] = 13cac3003
> (XEN) l1 = ffff83013cac3000
> (XEN) l1_index = 178
> (XEN) l1[178] = 0
> (XEN) l1[178] not present
> ata4.00: exception Emask 0x60 SAct 0x1f SErr 0x800 action 0x6 frozen
> ata4.00: irq_stat 0x20000000, host bus error
> ata4: SError: { HostInt }
> ata4.00: failed command: READ FPDMA QUEUED
> ata4.00: cmd 60/00:00:43:39:a2/04:00:0c:00:00/40 tag 0 ncq 524288 in
> res 40/00:24:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: READ FPDMA QUEUED
> ata4.00: cmd 60/00:08:43:35:a2/04:00:0c:00:00/40 tag 1 ncq 524288 in
> res 40/00:24:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: READ FPDMA QUEUED
> ata4.00: cmd 60/00:10:43:31:a2/04:00:0c:00:00/40 tag 2 ncq 524288 in
> res 40/00:24:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: READ FPDMA QUEUED
> ata4.00: cmd 60/00:18:43:2d:a2/04:00:0c:00:00/40 tag 3 ncq 524288 in
> res 40/00:24:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4.00: failed command: WRITE FPDMA QUEUED
> ata4.00: cmd 61/80:20:43:b1:a1/00:00:0c:00:00/40 tag 4 ncq 65536 out
> res 40/00:24:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host bus error)
> ata4.00: status: { DRDY }
> ata4: hard resetting link
> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata4.00: configured for UDMA/133
> sd 3:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
> sd 3:0:0:0: [sdd] Sense Key : Aborted Command [current] [descriptor]
> Descriptor sense data with sense descriptors (in hex):
> 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
> 0c a1 b1 43
> sd 3:0:0:0: [sdd] Add. Sense: No additional sense information
> sd 3:0:0:0: [sdd] CDB: Write(10): 2a 00 0c a1 b1 43 00 00 80 00
> end_request: I/O error, dev sdd, sector 211923267
> ata4: EH complete
> md: checkpointing resync of md0.
> RAID10 conf printout:
> --- wd:2 rd:4
> disk 0, wo:0, o:1, dev:sda3
> disk 2, wo:0, o:1, dev:sdc3
> disk 3, wo:1, o:0, dev:sdd3
> RAID10 conf printout:
> --- wd:2 rd:4
> disk 0, wo:0, o:1, dev:sda3
> disk 2, wo:0, o:1, dev:sdc3
> md: resync of RAID array md0
> md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
> md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
> md: using 128k window, over a total of 819199872 blocks.
> md: resuming resync of md0 from checkpoint.
> md: md0: resync done.
> RAID10 conf printout:
> --- wd:2 rd:4
> disk 0, wo:0, o:1, dev:sda3
> disk 2, wo:0, o:1, dev:sdc3
>
>
>
>
> =========================================================================
>
>
> __ __ _ _ _ _ _ _
> \ \/ /___ _ __ | || | / | _ _ _ __ ___| |_ __ _| |__ | | ___
> \ // _ \ '_ \ | || |_ | |__| | | | '_ \/ __| __/ _` | '_ \| |/ _ \
> / \ __/ | | | |__ _|| |__| |_| | | | \__ \ || (_| | |_) | | __/
> /_/\_\___|_| |_| |_|(_)_| \__,_|_| |_|___/\__\__,_|_.__/|_|\___|
>
> (XEN) Xen version 4.1-unstable (jeremy@) (gcc version 4.4.3 20100127 (Red Hat 4.4.3-4) (GCC) ) Tue Apr 6 17:23:29 PDT 2010
> (XEN) Latest ChangeSet: Tue Apr 06 17:23:12 2010 -0700 21115:ea6c67dc4577
> (XEN) Command line: com2=115200,8n1,0x3e8,5 console=com2,vga cpufreq=xen iommu=verbose
> (XEN) Video information:
> (XEN) VGA is text mode 80x25, font 8x16
> (XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
> (XEN) EDID info not retrieved because no DDC retrieval method detected
> (XEN) Disc information:
> (XEN) Found 4 MBR signatures
> (XEN) Found 4 EDD information structures
> (XEN) Xen-e820 RAM map:
> (XEN) 0000000000000000 - 000000000009d800 (usable)
> (XEN) 000000000009d800 - 00000000000a0000 (reserved)
> (XEN) 00000000000e0000 - 0000000000100000 (reserved)
> (XEN) 0000000000100000 - 00000000bf790000 (usable)
> (XEN) 00000000bf79e000 - 00000000bf7a0000 type 9
> (XEN) 00000000bf7a0000 - 00000000bf7ae000 (ACPI data)
> (XEN) 00000000bf7ae000 - 00000000bf7d0000 (ACPI NVS)
> (XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved)
> (XEN) 00000000bf7ed000 - 00000000c0000000 (reserved)
> (XEN) 00000000e0000000 - 00000000f0000000 (reserved)
> (XEN) 00000000fed20000 - 00000000fed40000 (reserved)
> (XEN) 00000000fee00000 - 00000000fee01000 (reserved)
> (XEN) 0000000100000000 - 0000000140000000 (usable)
> (XEN) ACPI: RSDP 000FA110, 0024 (r2 ACPIAM)
> (XEN) ACPI: XSDT BF7A0100, 0084 (r1 SMCI 20100225 MSFT 97)
> (XEN) ACPI: FACP BF7A0290, 00F4 (r4 022510 FACP1918 20100225 MSFT 97)
> (XEN) ACPI: DSDT BF7A05F0, 6C55 (r2 10605 10605000 0 INTL 20051117)
> (XEN) ACPI: FACS BF7AE000, 0040
> (XEN) ACPI: APIC BF7A0390, 0092 (r2 022510 APIC1918 20100225 MSFT 97)
> (XEN) ACPI: MCFG BF7A0430, 003C (r1 022510 OEMMCFG 20100225 MSFT 97)
> (XEN) ACPI: OEMB BF7AE040, 0073 (r1 022510 OEMB1918 20100225 MSFT 97)
> (XEN) ACPI: HPET BF7AA5F0, 0038 (r1 022510 OEMHPET 20100225 MSFT 97)
> (XEN) ACPI: GSCI BF7AE0C0, 2024 (r1 022510 GMCHSCI 20100225 MSFT 97)
> (XEN) ACPI: DMAR BF7B00F0, 0090 (r1 AMI OEMDMAR 1 MSFT 97)
> (XEN) ACPI: SSDT BF7B1580, 0363 (r1 DpgPmm CpuPm 12 INTL 20051117)
> (XEN) ACPI: EINJ BF7AA630, 0130 (r1 AMIER AMI_EINJ 20100225 MSFT 97)
> (XEN) ACPI: BERT BF7AA7C0, 0030 (r1 AMIER AMI_BERT 20100225 MSFT 97)
> (XEN) ACPI: ERST BF7AA7F0, 01B0 (r1 AMIER AMI_ERST 20100225 MSFT 97)
> (XEN) ACPI: HEST BF7AA9A0, 00A8 (r1 AMIER ABC_HEST 20100225 MSFT 97)
> (XEN) System RAM: 4056MB (4153584kB)
> (XEN) No NUMA configuration found
> (XEN) Faking a node at 0000000000000000-0000000140000000
> (XEN) Domain heap initialised
> (XEN) found SMP MP-table at 000ff780
> (XEN) DMI present.
> (XEN) Using APIC driver default
> (XEN) ACPI: PM-Timer IO Port: 0x808
> (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0]
> (XEN) ACPI: wakeup_vec[bf7ae00c], vec_size[20]
> (XEN) ACPI: Local APIC address 0xfee00000
> (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> (XEN) Processor #0 7:14 APIC version 21
> (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
> (XEN) Processor #2 7:14 APIC version 21
> (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
> (XEN) Processor #4 7:14 APIC version 21
> (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
> (XEN) Processor #6 7:14 APIC version 21
> (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled)
> (XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled)
> (XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled)
> (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled)
> (XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
> (XEN) ACPI: IOAPIC (id[0x07] address[0xfec00000] gsi_base[0])
> (XEN) IOAPIC[0]: apic_id 7, version 32, address 0xfec00000, GSI 0-23
> (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> (XEN) ACPI: IRQ0 used by override.
> (XEN) ACPI: IRQ2 used by override.
> (XEN) ACPI: IRQ9 used by override.
> (XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
> (XEN) ACPI: HPET id: 0x8086a701 base: 0xfed00000
> (XEN) [VT-D]dmar.c:679: Host address width 36
> (XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD:
> (XEN) [VT-D]dmar.c:398: dmaru->address = fed90000
> (XEN) [VT-D]dmar.c:411: flags: INCLUDE_ALL
> (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0
> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0
> (XEN) [VT-D]dmar.c:571: RMRR region: base_addr ed000 end_address effff
> (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0
> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0
> (XEN) [VT-D]dmar.c:571: RMRR region: base_addr bf7ed000 end_address bf7fffff
> (XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
> (XEN) PCI: MCFG area at e0000000 reserved in E820
> (XEN) Using ACPI (MADT) for SMP configuration information
> (XEN) Using scheduler: SMP Credit Scheduler (credit)
> (XEN) Detected 2400.063 MHz processor.
> (XEN) Initing memory sharing.
> (XEN) EPT support 2M super page.
> (XEN) VMX: Supported advanced features:
> (XEN) - APIC MMIO access virtualisation
> (XEN) - APIC TPR shadow
> (XEN) - Extended Page Tables (EPT)
> (XEN) - Virtual-Processor Identifiers (VPID)
> (XEN) - Virtual NMI
> (XEN) - MSR direct-access bitmap
> (XEN) HVM: ASIDs enabled.
> (XEN) HVM: VMX enabled
> (XEN) HVM: Hardware Assisted Paging detected.
> (XEN) Intel machine check reporting enabled
> (XEN) [VT-D]iommu.c:1078: drhd->address = fed90000 iommu->reg = ffff82c3fff57000
> (XEN) [VT-D]iommu.c:1080: cap = c90780106f0462 ecap = f020e3
> (XEN) Intel VT-d Snoop Control supported.
> (XEN) Intel VT-d DMA Passthrough not supported.
> (XEN) Intel VT-d Queued Invalidation supported.
> (XEN) Intel VT-d Interrupt Remapping not supported.
> (XEN) I/O virtualisation enabled
> (XEN) I/O virtualisation for PV guests disabled
> (XEN) EPT support 2M super page.
> (XEN) EPT support 2M super page.
> (XEN) EPT support 2M super page.
> (XEN) Total of 4 processors activated.
> (XEN) ENABLING IO-APIC IRQs
> (XEN) -> Using new ACK method
> (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
> (XEN) TSC is reliable, synchronization unnecessary
> (XEN) Platform timer is 14.318MHz HPET
> �(XEN) Allocated console ring of 32 KiB.
> (XEN) microcode.c:73:d32767 microcode: CPU1 resumed
> (XEN) microcode.c:73:d32767 microcode: CPU2 resumed
> (XEN) Brought up 4 CPUs
> (XEN) microcode.c:73:d32767 microcode: CPU3 resumed
> (XEN) Turbo Mode detected!
> (XEN) HPET: 8 timers in total, 8 timers will be used for broadcast
> (XEN) ACPI sleep modes: S3
> (XEN) mcheck_poll: Machine check polling timer started.
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:0.0
> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:8.0
> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:8.1
> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:8.2
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:8.3
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:10.0
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:10.1
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.0
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.0
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.0
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3
> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 3:0.0
> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 4:0.0
> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 5:0.0
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.0
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.1
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.2
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.3
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.4
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.5
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.6
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.7
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.0
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.1
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.0
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.1
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.0
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.1
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.2
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.4
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.0
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.1
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.2
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.3
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.0
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.1
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.2
> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.3
> (XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg = ffff82c3fff57000
> (XEN) *** LOADING DOMAIN 0 ***
> (XEN) elf_parse_binary: phdr: paddr=0x1000000 memsz=0x69c000
> (XEN) elf_parse_binary: phdr: paddr=0x169c000 memsz=0xe3cb0
> (XEN) elf_parse_binary: phdr: paddr=0x1780000 memsz=0x888
> (XEN) elf_parse_binary: phdr: paddr=0x1781000 memsz=0x14498
> (XEN) elf_parse_binary: phdr: paddr=0x1796000 memsz=0x9f5000
> (XEN) elf_parse_binary: memory: 0x1000000 -> 0x218b000
> (XEN) elf_xen_parse_note: GUEST_OS = "linux"
> (XEN) elf_xen_parse_note: GUEST_VERSION = "2.6"
> (XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0"
> (XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000
> (XEN) elf_xen_parse_note: ENTRY = 0xffffffff81796200
> (XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff81009000
> (XEN) elf_xen_parse_note: FEATURES = "!writable_page_tables|pae_pgdir_above_4gb"
> (XEN) elf_xen_parse_note: PAE_MODE = "yes"
> (XEN) elf_xen_parse_note: LOADER = "generic"
> (XEN) elf_xen_parse_note: unknown xen elf note (0xd)
> (XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1
> (XEN) elf_xen_parse_note: HV_START_LOW = 0xffff800000000000
> (XEN) elf_xen_parse_note: PADDR_OFFSET = 0x0
> (XEN) elf_xen_addr_calc_check: addresses:
> (XEN) virt_base = 0xffffffff80000000
> (XEN) elf_paddr_offset = 0x0
> (XEN) virt_offset = 0xffffffff80000000
> (XEN) virt_kstart = 0xffffffff81000000
> (XEN) virt_kend = 0xffffffff8218b000
> (XEN) virt_entry = 0xffffffff81796200
> (XEN) p2m_base = 0xffffffffffffffff
> (XEN) Xen kernel: 64-bit, lsb, compat32
> (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x218b000
> (XEN) PHYSICAL MEMORY ARRANGEMENT:
> (XEN) Dom0 alloc.: 0000000138000000->000000013c000000 (981633 pages to be allocated)
> (XEN) VIRTUAL MEMORY ARRANGEMENT:
> (XEN) Loaded kernel: ffffffff81000000->ffffffff8218b000
> (XEN) Init. ramdisk: ffffffff8218b000->ffffffff82b69800
> (XEN) Phys-Mach map: ffffffff82b6a000->ffffffff83307408
> (XEN) Start info: ffffffff83308000->ffffffff833084b4
> (XEN) Page tables: ffffffff83309000->ffffffff83326000
> (XEN) Boot stack: ffffffff83326000->ffffffff83327000
> (XEN) TOTAL: ffffffff80000000->ffffffff83400000
> (XEN) ENTRY ADDRESS: ffffffff81796200
> (XEN) Dom0 has maximum 4 VCPUs
> (XEN) elf_load_binary: phdr 0 at 0xffffffff81000000 -> 0xffffffff8169c000
> (XEN) elf_load_binary: phdr 1 at 0xffffffff8169c000 -> 0xffffffff8177fcb0
> (XEN) elf_load_binary: phdr 2 at 0xffffffff81780000 -> 0xffffffff81780888
> (XEN) elf_load_binary: phdr 3 at 0xffffffff81781000 -> 0xffffffff81795498
> (XEN) elf_load_binary: phdr 4 at 0xffffffff81796000 -> 0xffffffff81830000
> (XEN) Scrubbing Free RAM: .done.
> (XEN) Xen trace buffers: disabled
> (XEN) Std. Loglevel: All
> (XEN) Guest Loglevel: All
> (XEN) Xen is relinquishing VGA console.
> (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen)
> (XEN) Freed 164kB init memory.
> mapping kernel into physical memory
> Xen: setup ISA identity maps
> about to get started...
> Initializing cgroup subsys cpuset
> Initializing cgroup subsys cpu
> Linux version 2.6.32.11 (jeremy@lilith.goop.org) (gcc version 4.4.3 20100127 (Red Hat 4.4.3-4) (GCC) ) #7 SMP PREEMPT Mon Apr 5 14:58:54 PDT 2010
> Command line: ro root=/dev/mapper/vg_lilith--raid-root LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us ignore_loglevel earlyprintk=xen console=hvc0 rdshell pcie_aspm=off
> KERNEL supported cpus:
> Intel GenuineIntel
> AMD AuthenticAMD
> Centaur CentaurHauls
> xen_release_chunk: looking at area pfn bf790-bf79e: 14 pages freed
> xen_release_chunk: looking at area pfn bf7e0-bf7ed: 13 pages freed
> xen_release_chunk: looking at area pfn c0000-e0000: 131072 pages freed
> xen_release_chunk: looking at area pfn f0000-fec00: 14977 pages freed
> xen_release_chunk: looking at area pfn fec01-fed20: 0 pages freed
> xen_release_chunk: looking at area pfn fed40-fee00: 0 pages freed
> released 146076 pages of unused memory
> BIOS-provided physical RAM map:
> Xen: 0000000000000000 - 000000000009d800 (usable)
> Xen: 000000000009d800 - 0000000000100000 (reserved)
> Xen: 0000000000100000 - 00000000bf790000 (usable)
> Xen: 00000000bf79e000 - 00000000bf7a0000 type 9
> Xen: 00000000bf7a0000 - 00000000bf7ae000 (ACPI data)
> Xen: 00000000bf7ae000 - 00000000bf7d0000 (ACPI NVS)
> Xen: 00000000bf7d0000 - 00000000bf7e0000 (reserved)
> Xen: 00000000bf7ed000 - 00000000c0000000 (reserved)
> Xen: 00000000e0000000 - 00000000f0000000 (reserved)
> Xen: 00000000fec00000 - 00000000fec01000 (reserved)
> Xen: 00000000fed20000 - 00000000fed40000 (reserved)
> Xen: 00000000fee00000 - 00000000fee01000 (reserved)
> debug: ignoring loglevel setting.
> bootconsole [xenboot0] enabled
> DMI present.
> last_pfn = 0xbf790 max_arch_pfn = 0x400000000
> x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
> initial memory mapped : 0 - 20000000
> init_memory_mapping: 0000000000000000-00000000bf790000
> 0000000000 - 00bf790000 page 4k
> kernel direct mapping tables up to bf790000 @ 100000-700000
> RAMDISK: 0218b000 - 02b69800
> ACPI: RSDP 00000000000fa110 00024 (v02 ACPIAM)
> ACPI: XSDT 00000000bf7a0100 00084 (v01 SMCI 20100225 MSFT 00000097)
> ACPI: FACP 00000000bf7a0290 000F4 (v04 022510 FACP1918 20100225 MSFT 00000097)
> ACPI: DSDT 00000000bf7a05f0 06C55 (v02 10605 10605000 00000000 INTL 20051117)
> ACPI: FACS 00000000bf7ae000 00040
> ACPI: APIC 00000000bf7a0390 00092 (v02 022510 APIC1918 20100225 MSFT 00000097)
> ACPI: MCFG 00000000bf7a0430 0003C (v01 022510 OEMMCFG 20100225 MSFT 00000097)
> ACPI: OEMB 00000000bf7ae040 00073 (v01 022510 OEMB1918 20100225 MSFT 00000097)
> ACPI: HPET 00000000bf7aa5f0 00038 (v01 022510 OEMHPET 20100225 MSFT 00000097)
> ACPI: GSCI 00000000bf7ae0c0 02024 (v01 022510 GMCHSCI 20100225 MSFT 00000097)
> ACPI: 00000000bf7b00f0 00090 (v01 AMI OEMDMAR 00000001 MSFT 00000097)
> ACPI: SSDT 00000000bf7b1580 00363 (v01 DpgPmm CpuPm 00000012 INTL 20051117)
> ACPI: EINJ 00000000bf7aa630 00130 (v01 AMIER AMI_EINJ 20100225 MSFT 00000097)
> ACPI: BERT 00000000bf7aa7c0 00030 (v01 AMIER AMI_BERT 20100225 MSFT 00000097)
> ACPI: ERST 00000000bf7aa7f0 001B0 (v01 AMIER AMI_ERST 20100225 MSFT 00000097)
> ACPI: HEST 00000000bf7aa9a0 000A8 (v01 AMIER ABC_HEST 20100225 MSFT 00000097)
> ACPI: Local APIC address 0xfee00000
> No NUMA configuration found
> Faking a node at 0000000000000000-00000000bf790000
> Bootmem setup node 0 0000000000000000-00000000bf790000
> NODE_DATA [0000000000001000 - 0000000000005fff]
> bootmap [0000000000008000 - 000000000001fef7] pages 18
> (8 early reservations) ==> bootmem [0000000000 - 00bf790000]
> #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
> #1 [0003309000 - 0003326000] XEN PAGETABLES ==> [0003309000 - 0003326000]
> #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
> #3 [0001000000 - 000216a048] TEXT DATA BSS ==> [0001000000 - 000216a048]
> #4 [000218b000 - 0002b69800] RAMDISK ==> [000218b000 - 0002b69800]
> #5 [0002b6a000 - 0003309000] XEN START INFO ==> [0002b6a000 - 0003309000]
> #6 [000216b000 - 000216b21b] BRK ==> [000216b000 - 000216b21b]
> #7 [0000100000 - 00006e0000] PGTABLE ==> [0000100000 - 00006e0000]
> found SMP MP-table at [ffff8800000ff780] ff780
> Zone PFN ranges:
> DMA 0x00000000 -> 0x00001000
> DMA32 0x00001000 -> 0x00100000
> Normal 0x00100000 -> 0x00100000
> Movable zone start PFN for each node
> early_node_map[2] active PFN ranges
> 0: 0x00000000 -> 0x0000009d
> 0: 0x00000100 -> 0x000bf790
> On node 0 totalpages: 784173
> DMA zone: 88 pages used for memmap
> DMA zone: 1507 pages reserved
> DMA zone: 2402 pages, LIFO batch:0
> DMA32 zone: 16762 pages used for memmap
> DMA32 zone: 763414 pages, LIFO batch:31
> ACPI: PM-Timer IO Port: 0x808
> ACPI: Local APIC address 0xfee00000
> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
> ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
> ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
> ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled)
> ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled)
> ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled)
> ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled)
> ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
> ACPI: IOAPIC (id[0x07] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: apic_id 7, version 0, address 0xfec00000, GSI 0-0
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> ERROR: Unable to locate IOAPIC for GSI 2
> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> ERROR: Unable to locate IOAPIC for GSI 9
> Using ACPI (MADT) for SMP configuration information
> ACPI: HPET id: 0x8086a701 base: 0xfed00000
> SMP: Allowing 4 CPUs, 0 hotplug CPUs
> nr_irqs_gsi: 256
> PM: Registered nosave memory: 000000000009d000 - 000000000009e000
> PM: Registered nosave memory: 000000000009e000 - 0000000000100000
> Allocating PCI resources starting at c0000000 (gap: c0000000:20000000)
> Booting paravirtualized kernel on Xen
> Xen version: 4.1-unstable (preserve-AD) (dom0)
> NR_CPUS:16 nr_cpumask_bits:16 nr_cpu_ids:4 nr_node_ids:1
> PERCPU: Embedded 28 pages/cpu @ffff88000336d000 s83096 r8192 d23400 u114688
> pcpu-alloc: s83096 r8192 d23400 u114688 alloc=28*4096
> pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
> trying to map vcpu_info 0 at ffff880003378020, mfn 13b378, offset 32
> cpu 0 using vcpu_info at ffff880003378020
> trying to map vcpu_info 1 at ffff880003394020, mfn 13b394, offset 32
> cpu 1 using vcpu_info at ffff880003394020
> trying to map vcpu_info 2 at ffff8800033b0020, mfn 13b3b0, offset 32
> cpu 2 using vcpu_info at ffff8800033b0020
> trying to map vcpu_info 3 at ffff8800033cc020, mfn 13b3cc, offset 32
> cpu 3 using vcpu_info at ffff8800033cc020
> Xen: using vcpu_info placement
> Built 1 zonelists in Node order, mobility grouping on. Total pages: 765816
> Policy zone: DMA32
> Kernel command line: ro root=/dev/mapper/vg_lilith--raid-root LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us ignore_loglevel earlyprintk=xen console=hvc0 rdshell pcie_aspm=off
> PCIe ASPM is disabled
> PID hash table entries: 4096 (order: 3, 32768 bytes)
> Initializing CPU#0
> DMA: Placing 64MB software IO TLB between ffff88000794a000 - ffff88000b94a000
> DMA: software IO TLB at phys 0x794a000 - 0xb94a000
> xen_swiotlb_fixup: buf=ffff88000794a000 size=67108864
> xen_swiotlb_fixup: buf=ffff88000b9aa000 size=32768
> Memory: 2960308k/3137088k available (4691k kernel code, 396k absent, 176384k reserved, 2987k data, 656k init)
> Hierarchical RCU implementation.
> NR_IRQS:4352 nr_irqs:1280
> xen: --> irq=0
> xen: --> irq=1
> xen: --> irq=2
> xen: --> irq=3
> xen: --> irq=4
> xen: --> irq=5
> xen: --> irq=6
> xen: --> irq=7
> xen: --> irq=8
> xen: --> irq=9
> xen: --> irq=10
> xen: --> irq=11
> xen: --> irq=12
> xen: --> irq=13
> xen: --> irq=14
> xen: --> irq=15
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> xen: sci override: source_irq=9 global_irq=9 trigger=c polarity=1
> xen: registering gsi 9 triggering 0 polarity 0
> xen_allocate_pirq: returning irq 9 for gsi 9
> xen: --> irq=9
> xen: acpi sci 9
> Console: colour VGA+ 80x25
> console [hvc0] enabled, bootconsole disabled
> console [hvc0] enabled, bootconsole disabled
> Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
> ... MAX_LOCKDEP_SUBCLASSES: 8
> ... MAX_LOCK_DEPTH: 48
> ... MAX_LOCKDEP_KEYS: 8191
> ... CLASSHASH_SIZE: 4096
> ... MAX_LOCKDEP_ENTRIES: 16384
> ... MAX_LOCKDEP_CHAINS: 32768
> ... CHAINHASH_SIZE: 16384
> memory used by lock dependency info: 5855 kB
> per task-struct memory footprint: 1920 bytes
> Xen: using vcpuop timer interface
> installing Xen timer for CPU 0
> alloc irq_desc for 1279 on node 0
> alloc kstat_irqs on node 0
> Detected 2400.062 MHz processor.
> Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.12 BogoMIPS (lpj=2400062)
> Security Framework initialized
> SELinux: Initializing.
> SELinux: Starting in permissive mode
> Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
> Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
> Mount-cache hash table entries: 256
> Initializing cgroup subsys ns
> Initializing cgroup subsys cpuacct
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 256K
> CPU: L3 cache: 8192K
> CPU 0/0x0 -> Node 0
> CPU: Unsupported number of siblings 16
> Performance Events: unsupported p6 CPU model 30 no PMU driver, software events only.
> lockdep: fixing up alternatives.
> SMP alternatives: switching to UP code
> ACPI: Core revision 20090903
> alloc irq_desc for 1278 on node 0
> alloc kstat_irqs on node 0
> cpu 0 spinlock event irq 1278
> alloc irq_desc for 1277 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1276 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1275 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1274 on node 0
> alloc kstat_irqs on node 0
> installing Xen timer for CPU 1
> alloc irq_desc for 1273 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1272 on node 0
> alloc kstat_irqs on node 0
> cpu 1 spinlock event irq 1272
> lockdep: fixing up alternatives.
> SMP alternatives: switching to SMP code
> alloc irq_desc for 1271 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1270 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1269 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1268 on node 0
> alloc kstat_irqs on node 0
> Initializing CPU#1
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 256K
> CPU: L3 cache: 8192K
> CPU 1/0x0 -> Node 0
> CPU: Unsupported number of siblings 16
> installing Xen timer for CPU 2
> alloc irq_desc for 1267 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1266 on node 0
> alloc kstat_irqs on node 0
> cpu 2 spinlock event irq 1266
> alloc irq_desc for 1265 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1264 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1263 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1262 on node 0
> alloc kstat_irqs on node 0
> Initializing CPU#2
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 256K
> CPU: L3 cache: 8192K
> CPU 2/0x0 -> Node 0
> CPU: Unsupported number of siblings 16
> installing Xen timer for CPU 3
> alloc irq_desc for 1261 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1260 on node 0
> alloc kstat_irqs on node 0
> cpu 3 spinlock event irq 1260
> alloc irq_desc for 1259 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1258 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1257 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1256 on node 0
> alloc kstat_irqs on node 0
> Initializing CPU#3
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 256K
> CPU: L3 cache: 8192K
> CPU 3/0x0 -> Node 0
> CPU: Unsupported number of siblings 16
> Brought up 4 CPUs
> Grant table initialized
> Time: 16:45:17 Date: 04/07/10
> NET: Registered protocol family 16
> alloc irq_desc for 1255 on node 0
> alloc kstat_irqs on node 0
> ACPI: bus type pci registered
> PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
> PCI: MCFG area at e0000000 reserved in E820
> PCI: Using MMCONFIG at e0000000 - efffffff
> PCI: Using configuration type 1 for base access
> bio: create slab<bio-0> at 0
> ERROR: Unable to locate IOAPIC for GSI 9
> ACPI: EC: Look up EC in DSDT
> ACPI Warning for \_SB_._OSC: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
> \_SB_:_OSC evaluation returned wrong type
> _OSC request data:1 6
> ACPI: Executed 1 blocks of module-level executable AML code
> ACPI: Interpreter enabled
> ACPI: (supports S0 S1 S4 S5)
> ACPI: Using IOAPIC for interrupt routing
> ACPI Warning: Incorrect checksum in table [OEMB] - 91, should be 8E (20090903/tbutils-314)
> ACPI Warning: Incorrect checksum in table [ ] - 7B, should be BF (20090903/tbutils-314)
> ACPI: No dock devices found.
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
> pci 0000:00:03.0: PME# disabled
> pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
> pci 0000:00:05.0: PME# disabled
> pci 0000:00:1a.0: reg 10 32bit mmio: [0xfb3fc000-0xfb3fc3ff]
> pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
> pci 0000:00:1a.0: PME# disabled
> pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
> pci 0000:00:1c.0: PME# disabled
> pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
> pci 0000:00:1c.4: PME# disabled
> pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
> pci 0000:00:1c.5: PME# disabled
> pci 0000:00:1d.0: reg 10 32bit mmio: [0xfb3fa000-0xfb3fa3ff]
> pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
> pci 0000:00:1d.0: PME# disabled
> pci 0000:00:1f.2: reg 10 io port: [0xb400-0xb407]
> pci 0000:00:1f.2: reg 14 io port: [0xbc00-0xbc03]
> pci 0000:00:1f.2: reg 18 io port: [0xb880-0xb887]
> pci 0000:00:1f.2: reg 1c io port: [0xb800-0xb803]
> pci 0000:00:1f.2: reg 20 io port: [0xb480-0xb49f]
> pci 0000:00:1f.2: reg 24 32bit mmio: [0xfb3f8000-0xfb3f87ff]
> pci 0000:00:1f.2: PME# supported from D3hot
> pci 0000:00:1f.2: PME# disabled
> pci 0000:00:1f.3: reg 10 64bit mmio: [0xfb3f6000-0xfb3f60ff]
> pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
> pci 0000:03:00.0: reg 10 32bit mmio: [0xfb420000-0xfb43ffff]
> pci 0000:03:00.0: reg 14 32bit mmio: [0xfb480000-0xfb4fffff]
> pci 0000:03:00.0: reg 18 io port: [0xcc00-0xcc1f]
> pci 0000:03:00.0: reg 1c 32bit mmio: [0xfb41c000-0xfb41ffff]
> pci 0000:03:00.0: reg 30 32bit mmio pref: [0xfb440000-0xfb47ffff]
> pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
> pci 0000:03:00.0: PME# disabled
> pci 0000:00:1c.0: bridge io port: [0xc000-0xcfff]
> pci 0000:00:1c.0: bridge 32bit mmio: [0xfb400000-0xfb4fffff]
> pci 0000:04:00.0: reg 10 32bit mmio: [0xfb5e0000-0xfb5fffff]
> pci 0000:04:00.0: reg 18 io port: [0xdc00-0xdc1f]
> pci 0000:04:00.0: reg 1c 32bit mmio: [0xfb5dc000-0xfb5dffff]
> pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
> pci 0000:04:00.0: PME# disabled
> pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff]
> pci 0000:00:1c.4: bridge 32bit mmio: [0xfb500000-0xfb5fffff]
> pci 0000:05:00.0: reg 10 32bit mmio: [0xfb6e0000-0xfb6fffff]
> pci 0000:05:00.0: reg 18 io port: [0xec00-0xec1f]
> pci 0000:05:00.0: reg 1c 32bit mmio: [0xfb6dc000-0xfb6dffff]
> pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
> pci 0000:05:00.0: PME# disabled
> pci 0000:00:1c.5: bridge io port: [0xe000-0xefff]
> pci 0000:00:1c.5: bridge 32bit mmio: [0xfb600000-0xfb6fffff]
> pci 0000:06:03.0: reg 10 32bit mmio pref: [0xfa000000-0xfaffffff]
> pci 0000:06:03.0: reg 14 32bit mmio: [0xfb7fc000-0xfb7fffff]
> pci 0000:06:03.0: reg 18 32bit mmio: [0xfb800000-0xfbffffff]
> pci 0000:00:1e.0: transparent bridge
> pci 0000:00:1e.0: bridge 32bit mmio: [0xfb700000-0xfbffffff]
> pci 0000:00:1e.0: bridge 64bit mmio pref: [0xfa000000-0xfaffffff]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR1E._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0ehci_hcd 0000:00:1a.0: port 1 high speed
> ehci_hcd 0000:00:1a.0: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> ahci 0000:00:1f.2: version 3.0
> xen: registering gsi 19 triggering 0 polarity 1
> alloc irq_desc for 19 on node 0
> alloc kstat_irqs on node 0
> xen: --> irq=19
> ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
> alloc irq_desc for 1247 on node 0
> alloc kstat_irqs on node 0
> ahci: SSS flag set, parallel bus scan disabled
> ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
> ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems sxs apst
> ahci 0000:00:1f.2: setting latency timer to 64
> scsi0 : ahci
> scsi1 : ahci
> scsi2 : ahci
> scsi3 : ahci
> scsi4 : ahci
> scsi5 : ahci
> ata1: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8100 irq 1247
> ata2: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8180 irq 1247
> ata3: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8200 irq 1247
> ata4: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8280 irq 1247
> ata5: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8300 irq 1247
> ata6: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8380 irq 1247
> usb 1-1: udev 2, busnum 1, minor = 1
> usb 1-1: New USB device found, idVendor=8087, idProduct=0020
> usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
> usb 1-1: usb_probe_device
> usb 1-1: configuration #1 chosen from 1 choice
> usb 1-1: adding 1-1:1.0 (config #1, interface 0)
> hub 1-1:1.0: usb_probe_interface
> hub 1-1:1.0: usb_probe_interface - got id
> hub 1-1:1.0: USB hub found
> hub 1-1:1.0: 6 ports detected
> hub 1-1:1.0: standalone hub
> hub 1-1:1.0: individual port power switching
> hub 1-1:1.0: individual port over-current protection
> hub 1-1:1.0: Single TT
> hub 1-1:1.0: TT requires at most 8 FS bit times (666 ns)
> hub 1-1:1.0: Port indicators are supported
> hub 1-1:1.0: power on to power good time: 100ms
> hub 1-1:1.0: local power source is good
> hub 1-1:1.0: enabling power on all ports
> hub 2-0:1.0: state 7 ports 2 chg 0002 evt 0000
> hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
> ehci_hcd 0000:00:1d.0: port 1 high speed
> ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> hub 1-1:1.0: port 2: status 0101 change 0001
> usb 2-1: new high speed USB device using ehci_hcd and address 2
> ehci_hcd 0000:00:1d.0: port 1 high speed
> ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> usb 1-1: link qh256-0001/ffff8800bc51f9c0 start 1 [1/0 us]
> usb 2-1: udev 2, busnum 2, minor = 129
> usb 2-1: New USB device found, idVendor=8087, idProduct=0020
> usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
> usb 2-1: usb_probe_device
> usb 2-1: configuration #1 chosen from 1 choice
> usb 2-1: adding 2-1:1.0 (config #1, interface 0)
> hub 2-1:1.0: usb_probe_interface
> hub 2-1:1.0: usb_probe_interface - got id
> hub 2-1:1.0: USB hub found
> hub 2-1:1.0: 8 ports detected
> hub 2-1:1.0: standalone hub
> hub 2-1:1.0: individual port power switching
> hub 2-1:1.0: individual port over-current protection
> hub 2-1:1.0: Single TT
> hub 2-1:1.0: TT requires at most 8 FS bit times (666 ns)
> hub 2-1:1.0: Port indicators are supported
> hub 2-1:1.0: power on to power good time: 100ms
> hub 2-1:1.0: local power source is good
> hub 2-1:1.0: enabling power on all ports
> hub 1-1:1.0: state 7 ports 6 chg 0004 evt 0000
> hub 1-1:1.0: port 2, status 0101, change 0000, 12 Mb/s
> hub 1-1:1.0: port 2 not reset yet, waiting 10ms
> usb 1-1.2: new full speed USB device using ehci_hcd and address 3
> ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> hub 1-1:1.0: port 2 not reset yet, waiting 10ms
> ata1.00: ATA-8: WDC WD10EADS-00P8B0, 01.00A01, max UDMA/133
> ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
> ata1.00: configured for UDMA/133
> scsi 0:0:0:0: Direct-Access ATA WDC WD10EADS-00P 01.0 PQ: 0 ANSI: 5
> sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sd 0:0:0:0: Attached scsi generic sg0 type 0
> sda:
> usb 2-1: link qh256-0001/ffff8800bc51f6c0 start 1 [1/0 us]
> sda1 sda2 sda3 sda4
> sd 0:0:0:0: [sda] Attached SCSI disk
> usb 1-1.2: skipped 1 descriptor after interface
> usb 1-1.2: skipped 1 descriptor after interface
> usb 1-1.2: default language 0x0409
> usb 1-1.2: udev 3, busnum 1, minor = 2
> usb 1-1.2: New USB device found, idVendor=0557, idProduct=2221
> usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
> usb 1-1.2: Product: Hermon USB hidmouse Device
> usb 1-1.2: Manufacturer: Winbond Electronics Corp
> usb 1-1.2: usb_probe_device
> usb 1-1.2: configuration #1 chosen from 1 choice
> usb 1-1.2: adding 1-1.2:1.0 (config #1, interface 0)
> usbhid 1-1.2:1.0: usb_probe_interface
> usbhid 1-1.2:1.0: usb_probe_interface - got id
> input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input4
> generic-usb 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:1a.0-1.2/input0
> usb 1-1.2: adding 1-1.2:1.1 (config #1, interface 1)
> usbhid 1-1.2:1.1: usb_probe_interface
> usbhid 1-1.2:1.1: usb_probe_interface - got id
> input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.1/input/input5
> usb 1-1.2: link qh8-0601/ffff8800be6225c0 start 2 [1/2 us]
> generic-usb 0003:0557:2221.0002: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:1a.0-1.2/input1
> hub 2-1:1.0: state 7 ports 8 chg 0000 evt 0000
> hub 1-1:1.0: state 7 ports 6 chg 0000 evt 0004
> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata2.00: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
> ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
> ata2.00: configured for UDMA/133
> scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5
> sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
> sd 1:0:0:0: Attached scsi generic sg1 type 0
> sd 1:0:0:0: [sdb] Write Protect is off
> sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sdb: sdb1 sdb2 sdb3 sdb4
> sd 1:0:0:0: [sdb] Attached SCSI disk
> input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input6
> ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata3.00: ATA-8: WDC WD10EADS-00P8B0, 01.00A01, max UDMA/133
> ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
> ata3.00: configured for UDMA/133
> scsi 2:0:0:0: Direct-Access ATA WDC WD10EADS-00P 01.0 PQ: 0 ANSI: 5
> sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
> sd 2:0:0:0: Attached scsi generic sg2 type 0
> sd 2:0:0:0: [sdc] Write Protect is off
> sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
> sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sdc: sdc1 sdc2 sdc3 sdc4
> sd 2:0:0:0: [sdc] Attached SCSI disk
> hub 2-1:1.0: hub_suspend
> usb 2-1: unlink qh256-0001/ffff8800bc51f6c0 start 1 [1/0 us]
> usb 2-1: usb auto-suspend
> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata4.00: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
> ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
> ata4.00: configured for UDMA/133
> scsi 3:0:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5
> sd 3:0:0:0: [sdd] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
> sd 3:0:0:0: Attached scsi generic sg3 type 0
> sd 3:0:0:0: [sdd] Write Protect is off
> sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
> sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sdd: sdd1 sdd2 sdd3 sdd4
> sd 3:0:0:0: [sdd] Attached SCSI disk
> ata5: SATA link down (SStatus 0 SControl 300)
> ata6: SATA link down (SStatus 0 SControl 300)
> md: raid10 personality registered for level 10
> Intel AES-NI instructions are not detected.
> md: md0 stopped.
> md: bind<sdb3>
> md: bind<sdc3>
> md: bind<sdd3>
> md: bind<sda3>
> md: kicking non-fresh sdd3 from array!
> md: unbind<sdd3>
> md: export_rdev(sdd3)
> md: kicking non-fresh sdb3 from array!
> md: unbind<sdb3>
> md: export_rdev(sdb3)
> raid10: raid set md0 active with 2 out of 4 devices
> md0: detected capacity change from 0 to 838860668928
> md0: unknown partition table
> hub 2-0:1.0: hub_suspend
> usb usb2: bus auto-suspend
> ehci_hcd 0000:00:1d.0: suspend root hub
>
> Password:***********
> EXT4-fs (dm-2): mounted filesystem with ordered data mode
> type=1404 audit(1270658817.238:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
> SELinux: 8192 avtab hash slots, 162639 rules.
> SELinux: 8192 avtab hash slots, 162639 rules.
> SELinux: 8 users, 12 roles, 3092 types, 152 bools, 1 sens, 1024 cats
> SELinux: 77 classes, 162639 rules
> SELinux: Completing initialization.
> SELinux: Setting up existing superblocks.
> SELinux: initialized (dev dm-2, type ext4), uses xattr
> SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
> SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
> SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
> SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs
> SELinux: initialized (dev devpts, type devpts), uses transition SIDs
> SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
> SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
> SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
> SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
> SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
> SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
> SELinux: initialized (dev proc, type proc), uses genfs_contexts
> SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
> SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
> SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
> type=1403 audit(1270658817.689:3): policy loaded auid=4294967295 ses=4294967295
> Welcome to Fedora
> Press 'I' to enter interactive startup.
> Starting udev: udev: starting version 145
> ACPI: SSDT 00000000bf7b0180 00F20 (v01 DpgPmm P001Ist 00000011 INTL 20051117)
> ACPI: SSDT 00000000bf7b10a0 004D5 (v01 PmRef P001Cst 00003001 INTL 20051117)
> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> (XEN) Monitor-Mwait will be used to enter C-1 state
> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> (XEN) Monitor-Mwait will be used to enter C-2 state
> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> (XEN) Monitor-Mwait will be used to enter C-3 state
> ACPI: CPU-1 (power states: C1[C1] C2[C2] C3[C3])
> e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
> e1000e: Copyright (c) 1999-2008 Intel Corporation.
> xen: registering gsi 16 triggering 0 polarity 1
> xen_allocate_pirq: returning irq 16 for gsi 16
> xen: --> irq=16
> Already setup the GSI :16
> e1000e 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
> e1000e 0000:03:00.0: setting latency timer to 64
> alloc irq_desc for 1246 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1245 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1244 on node 0
> alloc kstat_irqs on node 0
> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> (XEN) Monitor-Mwait will be used to enter C-1 state
> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> (XEN) Monitor-Mwait will be used to enter C-2 state
> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> (XEN) Monitor-Mwait will be used to enter C-3 state
> ACPI: CPU-1 (power states: C1[C1] C2[C2] C3[C3])
> 0000:03:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1b:21:4f:65:6b
> 0000:03:00.0: eth0: Intel(R) PRO/1000 Network Connection
> 0000:03:00.0: eth0: MAC: 3, PHY: 8, PBA No: e46981-003
> xen: registering gsi 16 triggering 0 polarity 1
> xen_allocate_pirq: returning irq 16 for gsi 16
> xen: --> irq=16
> Already setup the GSI :16
> e1000e 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
> e1000e 0000:04:00.0: setting latency timer to 64
> alloc irq_desc for 1243 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1242 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1241 on node 0
> alloc kstat_irqs on node 0
> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> (XEN) Monitor-Mwait will be used to enter C-1 state
> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> (XEN) Monitor-Mwait will be used to enter C-2 state
> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> (XEN) Monitor-Mwait will be used to enter C-3 state
> ACPI: CPU-1 (power states: C1[C1] C2[C2] C3[C3])
> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> (XEN) Monitor-Mwait will be used to enter C-1 state
> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> (XEN) Monitor-Mwait will be used to enter C-2 state
> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> (XEN) Monitor-Mwait will be used to enter C-3 state
> ACPI: CPU-1 (power states: C1[C1] C2[C2] C3[C3])
> 0000:04:00.0: eth1: (PCI Express:2.5GB/s:Width x1) 00:30:48:dd:eb:66
> 0000:04:00.0: eth1: Intel(R) PRO/1000 Network Connection
> 0000:04:00.0: eth1: MAC: 3, PHY: 8, PBA No: 0101ff-0ff
> xen: registering gsi 17 triggering 0 polarity 1
> xen_allocate_pirq: returning irq 17 for gsi 17
> xen: --> irq=17
> Already setup the GSI :17
> e1000e 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
> e1000e 0000:05:00.0: setting latency timer to 64
> alloc irq_desc for 1240 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1239 on node 0
> alloc kstat_irqs on node 0
> alloc irq_desc for 1238 on node 0
> alloc kstat_irqs on node 0
> 0000:05:00.0: eth2: (PCI Express:2.5GB/s:Width x1) 00:30:48:dd:eb:67
> 0000:05:00.0: eth2: Intel(R) PRO/1000 Network Connection
> 0000:05:00.0: eth2: MAC: 3, PHY: 8, PBA No: 0101ff-0ff
> udev: renamed network interface eth2 to eth1
> udev: renamed network interface eth0 to eth2
> udev: renamed network interface eth1_rename to eth0
> mdadm: /dev/md0 is already in use.
> Key slot 0 unlocked.
> Key slot 0 unlocked.
> device-mapper: multipath: version 1.1.0 loaded
> Setting up Logical Volume Management: 14 logical volume(s) in volume group "vg_lilith-raid" now active
> [ OK ]
> Checking filesystems
> Checking all file systems.
> [/sbin/fsck.ext4 (1) -- /] fsck.ext4 -a /dev/mapper/vg_lilith--raid-root
> /dev/mapper/vg_lilith--raid-root contains a file system with errors, check forced.
> /dev/mapper/vg_lilith--raid-root: 343615/2564096 files (0.2% non-contiguous), 2390774/10240000 blocks
> [/sbin/fsck.ext4 (1) -- /boot] fsck.ext4 -a /dev/sda2
> [/sbin/fsck.ext4 (2) -- /boot-spare] fsck.ext4 -a /dev/sdb2
> /dev/sdb2: clean, 11/66384 files, 12695/265072 blocks
> /dev/sda2: clean, 89/66384 files, 69878/265072 blocks
> [/sbin/fsck.ext4 (1) -- /home] fsck.ext4 -a /dev/mapper/luks-11eb0145-088a-4c13-acf4-9784e82bb1e3
> /dev/mapper/luks-11eb0145-088a-4c13-acf4-9784e82bb1e3: clean, 506715/12804096 files, 10193956/51199495 blocks
> [/sbin/fsck.ext4 (1) -- /var] fsck.ext4 -a /dev/mapper/luks-37e6b844-a112-427c-be60-ae6f4d9c5041
> /dev/mapper/luks-37e6b844-a112-427c-be60-ae6f4d9c5041: clean, 21026/5120000 files, 490586/20479495 blocks
> [ OK ]
> Remounting root filesystem in read-write mode: [ OK ]
> Mounting local filesystems: EXT4-fs (sda2): mounted filesystem with ordered data mode
> SELinux: initialized (dev sda2, type ext4), uses xattr
> EXT4-fs (sdb2): mounted filesystem with ordered data mode
> SELinux: initialized (dev sdb2, type ext4), uses xattr
> EXT4-fs (dm-15): mounted filesystem with ordered data mode
> SELinux: initialized (dev dm-15, type ext4), uses xattr
> EXT4-fs (dm-16): mounted filesystem with ordered data mode
> SELinux: initialized (dev dm-16, type ext4), uses xattr
> SELinux: initialized (dev xenfs, type xenfs), uses genfs_contexts
> [ OK ]
> Enabling local filesystem quotas: [ OK ]
> Enabling /etc/fstab swaps: Adding 16381972k swap on /dev/mapper/luks-2aac27aa-0bb6-46cc-8a7a-83af1ca296a2. Priority:-1 extents:1 across:16381972k
> [ OK ]
> SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
> Entering non-interactive startup
> Applying Intel CPU microcode update: platform microcode: firmware: requesting intel-ucode/06-1e-05
> platform microcode: firmware: requesting intel-ucode/06-1e-05
> platform microcode: firmware: requesting intel-ucode/06-1e-05
> platform microcode: firmware: requesting intel-ucode/06-1e-05
> Microcode Update Driver: v2.00<tigran@aivazian.fsnet.co.uk>, Peter Oruba
> Microcode Update Driver: v2.00 removed.
> Starting monitoring for VG vg_lilith-raid: 14 logical volume(s) in volume group "vg_lilith-raid" monitored
> [ OK ]
> ip6tables: Applying firewall rules: [ OK ]
> ip6tables: Loading additional modules: nf_conntrack_netbios_ns [ OK ]
> Starting auditd: [ OK ]
> Starting portreserve: [ OK ]
> Starting system logger: [ OK ]
> Starting irqbalance: [ OK ]
> Starting rpcbind: [ OK ]
> Starting mdmonitor: [ OK ]
> Starting system message bus: [ OK ]
> Starting Avahi daemon... [ OK ]
> Starting NFS statd: [ OK ]
> Starting RPC idmapd: FATAL: Module sunrpc not found.
> FATAL: Error running install command for sunrpc
> Error: RPC MTAB does not exist.
> Starting cups: [ OK ]
> Starting acpi daemon: [ OK ]
> Starting HAL daemon: [ OK ]
> Starting PC/SC smart card daemon (pcscd): [ OK ]
> Retrigger failed udev events[ OK ]
> Setting network parameters... [ OK ]
> Starting NetworkManager daemon: [ OK ]
> Enabling Bluetooth devices:
> Starting sshd: [ OK ]
> ADDRCONF(NETDEV_UP): eth2: link is not ready
> ntpdate: Synchronizing with time server: ADDRCONF(NETDEV_UP): eth0: link is not ready
> ADDRCONF(NETDEV_UP): eth1: link is not ready
> [FAILED]
> Starting ntpd: [ OK ]
> Starting abrt daemon: [ OK ]
> usb 1-1.2: link qh8-0601/ffff8800b58ba740 start 3 [1/2 us]
>
> [ OK ] crond: [ OK ]
> Enabling monthly Smolt checkin: [ OK ]
> [ OK ] atd: [ OK ]
> Starting libvirtd daemon: [ OK ]
> Bridge firewalling registered
> virbr0: starting userspace STP failed, starting kernel STP
> e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
> ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
> e1000e: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
> ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
> e1000e: eth0 NICMbps Full Duplex, Flow Control: RX/TX
> ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
> SELinux: initialized (dev proc, type proc), uses genfs_contexts
> SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
>
> Fedora release 12 (Constantine)
> Kernel 2.6.32.11 on an x86_64 (/dev/hvc0)
>
> lilith.goop.org login: usb usb2: usb auto-resume
> ehci_hcd 0000:00:1d.0: resume root hub
> hub 2-0:1.0: hub_resume
> hub 2-0:1.0: port 1: status 0507 change 0000
> usb 2-1: usb auto-resume
> hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
> ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> usb 2-1: finish resume
> hub 2-1:1.0: hub_resume
> ehci_hcd 0000:00:1d.0: reused qh ffff8800bc51f6c0 schedule
> usb 2-1: link qh256-0001/ffff8800bc51f6c0 start 1 [1/0 us]
> hub 2-1:1.0: state 7 ports
>
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: New DMAR errors in Xen 4.1
2010-04-08 2:32 ` Weidong Han
@ 2010-04-08 16:58 ` Jeremy Fitzhardinge
0 siblings, 0 replies; 7+ messages in thread
From: Jeremy Fitzhardinge @ 2010-04-08 16:58 UTC (permalink / raw)
To: Weidong Han; +Cc: Xen-devel, Keir Fraser
On 04/07/2010 07:32 PM, Weidong Han wrote:
> Jeremy Fitzhardinge wrote:
>> On 04/06/2010 07:50 PM, Weidong Han wrote:
>>
>>>> It turns out its... "Enable debug=y by default in the build." So I
>>>> guess these errors have been happening silently thus far?
>>>>
>>>> J
>>>>
>>> I don't encounter this issue. These DMAR fault messages will be
>>> printed even when debug=n. what platform are you using? could you post
>>> complete booting log with "iommu=verbose"?
>>>
>>
>> This is a Supermicro X8SIL-F system, which is a Lynnfield + Ibex Peak
>> system.
>>
>> I've attached two boot logs below. The first is one where there lots of
>> DMAR errors early, and the system is a disaster (basically doesn't come
>> up, lots of devices fail to init). Unfortunately it looks like I
>> mistyped "verbose".
>>
>> The second boot was immediately after the first and it comes up cleanly
>> with no DMAR errors at all. So it appears there's some non-determinism
>> there. The gmfns in the messages always appear to be about he same, so
>> I wonder if it depends on exactly what pages the kernel ends up
>> allocating for IO? (It probably also means my bisection results are
>> suspect.)
>>
> the boot log with "iommu=verbose" looks fine. when you mistyped
> "verbose", it equals to default iommu setting, that's iommu=1.
>
> Can I understand that: the DMAR faults only occur when "debug=y" with
> default iommu setting (iommu=1)?
I usually use iommu=pv; is that equivalent?
Sometimes it appears to just work with no DMAR errors at all. I'm not
at all confident about by bisection.
> Besides print more info, "iommu=verbose" also invokes
> process_pending_softirqs in domain_context_mapping. Could you try
> below patch to also call process_pending_softirqs for "iommu=1"?
Will do.
>
> diff -r 28e5409e3fb3 xen/drivers/passthrough/vtd/iommu.c
> --- a/xen/drivers/passthrough/vtd/iommu.c Wed Apr 07 16:22:05
> 2010 +0100
> +++ b/xen/drivers/passthrough/vtd/iommu.c Thu Apr 08 10:18:15
> 2010 +0800
> @@ -1366,7 +1366,7 @@ static int domain_context_mapping(struct
> break;
> }
>
> - if ( iommu_verbose )
> +// if ( iommu_verbose )
> process_pending_softirqs();
>
> return ret;
J
>
>> (BTW, what's a "type 9" E820 region?)
>>
>> Thanks,
>> J
>>
>>
>> __ __ _ _ _ _ _ _
>> \ \/ /___ _ __ | || | / | _ _ _ __ ___| |_ __ _| |__ | | ___
>> \ // _ \ '_ \ | || |_ | |__| | | | '_ \/ __| __/ _` | '_ \| |/ _ \
>> / \ __/ | | | |__ _|| |__| |_| | | | \__ \ || (_| | |_) | | __/
>> /_/\_\___|_| |_| |_|(_)_| \__,_|_| |_|___/\__\__,_|_.__/|_|\___|
>>
>> (XEN) Xen version 4.1-unstable (jeremy@) (gcc version 4.4.3 20100127
>> (Red Hat 4.4.3-4) (GCC) ) Tue Apr 6 17:23:29 PDT 2010
>> (XEN) Latest ChangeSet: Tue Apr 06 17:23:12 2010 -0700
>> 21115:ea6c67dc4577
>> (XEN) Command line: com2=115200,8n1,0x3e8,5 console=com2,vga
>> cpufreq=xen iommu=verbos8
>> (XEN) Video information:
>> (XEN) VGA is text mode 80x25, font 8x16
>> (XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
>> (XEN) EDID info not retrieved because no DDC retrieval method detected
>> (XEN) Disc information:
>> (XEN) Found 4 MBR signatures
>> (XEN) Found 4 EDD information structures
>> (XEN) Xen-e820 RAM map:
>> (XEN) 0000000000000000 - 000000000009d800 (usable)
>> (XEN) 000000000009d800 - 00000000000a0000 (reserved)
>> (XEN) 00000000000e0000 - 0000000000100000 (reserved)
>> (XEN) 0000000000100000 - 00000000bf790000 (usable)
>> (XEN) 00000000bf79e000 - 00000000bf7a0000 type 9
>> (XEN) 00000000bf7a0000 - 00000000bf7ae000 (ACPI data)
>> (XEN) 00000000bf7ae000 - 00000000bf7d0000 (ACPI NVS)
>> (XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved)
>> (XEN) 00000000bf7ed000 - 00000000c0000000 (reserved)
>> (XEN) 00000000e0000000 - 00000000f0000000 (reserved)
>> (XEN) 00000000fed20000 - 00000000fed40000 (reserved)
>> (XEN) 00000000fee00000 - 00000000fee01000 (reserved)
>> (XEN) 0000000100000000 - 0000000140000000 (usable)
>> (XEN) ACPI: RSDP 000FA110, 0024 (r2 ACPIAM)
>> (XEN) ACPI: XSDT BF7A0100, 0084 (r1 SMCI 20100225
>> MSFT 97)
>> (XEN) ACPI: FACP BF7A0290, 00F4 (r4 022510 FACP1918 20100225
>> MSFT 97)
>> (XEN) ACPI: DSDT BF7A05F0, 6C55 (r2 10605 10605000 0 INTL
>> 20051117)
>> (XEN) ACPI: FACS BF7AE000, 0040
>> (XEN) ACPI: APIC BF7A0390, 0092 (r2 022510 APIC1918 20100225
>> MSFT 97)
>> (XEN) ACPI: MCFG BF7A0430, 003C (r1 022510 OEMMCFG 20100225
>> MSFT 97)
>> (XEN) ACPI: OEMB BF7AE040, 0073 (r1 022510 OEMB1918 20100225
>> MSFT 97)
>> (XEN) ACPI: HPET BF7AA5F0, 0038 (r1 022510 OEMHPET 20100225
>> MSFT 97)
>> (XEN) ACPI: GSCI BF7AE0C0, 2024 (r1 022510 GMCHSCI 20100225
>> MSFT 97)
>> (XEN) ACPI: DMAR BF7B00F0, 0090 (r1 AMI OEMDMAR 1
>> MSFT 97)
>> (XEN) ACPI: SSDT BF7B1580, 0363 (r1 DpgPmm CpuPm 12 INTL
>> 20051117)
>> (XEN) ACPI: EINJ BF7AA630, 0130 (r1 AMIER AMI_EINJ 20100225
>> MSFT 97)
>> (XEN) ACPI: BERT BF7AA7C0, 0030 (r1 AMIER AMI_BERT 20100225
>> MSFT 97)
>> (XEN) ACPI: ERST BF7AA7F0, 01B0 (r1 AMIER AMI_ERST 20100225
>> MSFT 97)
>> (XEN) ACPI: HEST BF7AA9A0, 00A8 (r1 AMIER ABC_HEST 20100225
>> MSFT 97)
>> (XEN) System RAM: 4056MB (4153584kB)
>> (XEN) No NUMA configuration found
>> (XEN) Faking a node at 0000000000000000-0000000140000000
>> (XEN) Domain heap initialised
>> (XEN) found SMP MP-table at 000ff780
>> (XEN) DMI present.
>> (XEN) Using APIC driver default
>> (XEN) ACPI: PM-Timer IO Port: 0x808
>> (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0]
>> (XEN) ACPI: wakeup_vec[bf7ae00c], vec_size[20]
>> (XEN) ACPI: Local APIC address 0xfee00000
>> (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
>> (XEN) Processor #0 7:14 APIC version 21
>> (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
>> (XEN) Processor #2 7:14 APIC version 21
>> (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
>> (XEN) Processor #4 7:14 APIC version 21
>> (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
>> (XEN) Processor #6 7:14 APIC version 21
>> (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled)
>> (XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled)
>> (XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled)
>> (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled)
>> (XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
>> (XEN) ACPI: IOAPIC (id[0x07] address[0xfec00000] gsi_base[0])
>> (XEN) IOAPIC[0]: apic_id 7, version 32, address 0xfec00000, GSI 0-23
>> (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
>> (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
>> (XEN) ACPI: IRQ0 used by override.
>> (XEN) ACPI: IRQ2 used by override.
>> (XEN) ACPI: IRQ9 used by override.
>> (XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
>> (XEN) ACPI: HPET id: 0x8086a701 base: 0xfed00000
>> (XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
>> (XEN) PCI: MCFG area at e0000000 reserved in E820
>> (XEN) Using ACPI (MADT) for SMP configuration information
>> (XEN) Using scheduler: SMP Credit Scheduler (credit)
>> (XEN) Detected 2400.067 MHz processor.
>> (XEN) Initing memory sharing.
>> (XEN) EPT support 2M super page.
>> (XEN) VMX: Supported advanced features:
>> (XEN) - APIC MMIO access virtualisation
>> (XEN) - APIC TPR shadow
>> (XEN) - Extended Page Tables (EPT)
>> (XEN) - Virtual-Processor Identifiers (VPID)
>> (XEN) - Virtual NMI
>> (XEN) - MSR direct-access bitmap
>> (XEN) HVM: ASIDs enabled.
>> (XEN) HVM: VMX enabled
>> (XEN) HVM: Hardware Assisted Paging detected.
>> (XEN) Intel machine check reporting enabled
>> (XEN) Intel VT-d Snoop Control supported.
>> (XEN) Intel VT-d DMA Passthrough not supported.
>> (XEN) Intel VT-d Queued Invalidation supported.
>> (XEN) Intel VT-d Interrupt Remapping not supported.
>> (XEN) I/O virtualisation enabled
>> (XEN) I/O virtualisation for PV guests disabled
>> (XEN) EPT support 2M super page.
>> (XEN) EPT support 2M super page.
>> (XEN) EPT support 2M super page.
>> (XEN) Total of 4 processors activated.
>> (XEN) ENABLING IO-APIC IRQs
>> (XEN) -> Using new ACK method
>> (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
>> (XEN) TSC is reliable, synchronization unnecessary
>> (XEN) Platform timer is 14.318MHz HPET
>> �(XEN) Allocated console ring of 32 KiB.
>> (XEN) microcode.c:73:d32767 microcode: CPU1 resumed
>> (XEN) microcode.c:73:d32767 microcode: CPU2 resumed
>> (XEN) Brought up 4 CPUs
>> (XEN) microcode.c:73:d32767 microcode: CPU3 resumed
>> (XEN) Turbo Mode detected!
>> (XEN) HPET: 8 timers in total, 8 timers will be used for broadcast
>> (XEN) ACPI sleep modes: S3
>> (XEN) mcheck_poll: Machine check polling timer started.
>> (XEN) *** LOADING DOMAIN 0 ***
>> (XEN) elf_parse_binary: phdr: paddr=0x1000000 memsz=0x69c000
>> (XEN) elf_parse_binary: phdr: paddr=0x169c000 memsz=0xe3cb0
>> (XEN) elf_parse_binary: phdr: paddr=0x1780000 memsz=0x888
>> (XEN) elf_parse_binary: phdr: paddr=0x1781000 memsz=0x14498
>> (XEN) elf_parse_binary: phdr: paddr=0x1796000 memsz=0x9f5000
>> (XEN) elf_parse_binary: memory: 0x1000000 -> 0x218b000
>> (XEN) elf_xen_parse_note: GUEST_OS = "linux"
>> (XEN) elf_xen_parse_note: GUEST_VERSION = "2.6"
>> (XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0"
>> (XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000
>> (XEN) elf_xen_parse_note: ENTRY = 0xffffffff81796200
>> (XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff81009000
>> (XEN) elf_xen_parse_note: FEATURES =
>> "!writable_page_tables|pae_pgdir_above_4gb"
>> (XEN) elf_xen_parse_note: PAE_MODE = "yes"
>> (XEN) elf_xen_parse_note: LOADER = "generic"
>> (XEN) elf_xen_parse_note: unknown xen elf note (0xd)
>> (XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1
>> (XEN) elf_xen_parse_note: HV_START_LOW = 0xffff800000000000
>> (XEN) elf_xen_parse_note: PADDR_OFFSET = 0x0
>> (XEN) elf_xen_addr_calc_check: addresses:
>> (XEN) virt_base = 0xffffffff80000000
>> (XEN) elf_paddr_offset = 0x0
>> (XEN) virt_offset = 0xffffffff80000000
>> (XEN) virt_kstart = 0xffffffff81000000
>> (XEN) virt_kend = 0xffffffff8218b000
>> (XEN) virt_entry = 0xffffffff81796200
>> (XEN) p2m_base = 0xffffffffffffffff
>> (XEN) Xen kernel: 64-bit, lsb, compat32
>> (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x218b000
>> (XEN) PHYSICAL MEMORY ARRANGEMENT:
>> (XEN) Dom0 alloc.: 0000000138000000->000000013c000000 (981633
>> pages to be allocated)
>> (XEN) VIRTUAL MEMORY ARRANGEMENT:
>> (XEN) Loaded kernel: ffffffff81000000->ffffffff8218b000
>> (XEN) Init. ramdisk: ffffffff8218b000->ffffffff82b69800
>> (XEN) Phys-Mach map: ffffffff82b6a000->ffffffff83307408
>> (XEN) Start info: ffffffff83308000->ffffffff833084b4
>> (XEN) Page tables: ffffffff83309000->ffffffff83326000
>> (XEN) Boot stack: ffffffff83326000->ffffffff83327000
>> (XEN) TOTAL: ffffffff80000000->ffffffff83400000
>> (XEN) ENTRY ADDRESS: ffffffff81796200
>> (XEN) Dom0 has maximum 4 VCPUs
>> (XEN) elf_load_binary: phdr 0 at 0xffffffff81000000 ->
>> 0xffffffff8169c000
>> (XEN) elf_load_binary: phdr 1 at 0xffffffff8169c000 ->
>> 0xffffffff8177fcb0
>> (XEN) elf_load_binary: phdr 2 at 0xffffffff81780000 ->
>> 0xffffffff81780888
>> (XEN) elf_load_binary: phdr 3 at 0xffffffff81781000 ->
>> 0xffffffff81795498
>> (XEN) elf_load_binary: phdr 4 at 0xffffffff81796000 ->
>> 0xffffffff81830000
>> (XEN) Scrubbing Free RAM: .done.
>> (XEN) Xen trace buffers: disabled
>> (XEN) Std. Loglevel: All
>> (XEN) Guest Loglevel: All
>> (XEN) Xen is relinquishing VGA console.
>> (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch
>> input to Xen)
>> (XEN) Freed 164kB init memory.
>> mapping kernel into physical memory
>> Xen: setup ISA identity maps
>> about to get started...
>> Initializing cgroup subsys cpuset
>> Initializing cgroup subsys cpu
>> Linux version 2.6.32.11 (jeremy@lilith.goop.org) (gcc version 4.4.3
>> 20100127 (Red Hat 4.4.3-4) (GCC) ) #7 SMP PREEMPT Mon Apr 5 14:58:54
>> PDT 2010
>> Command line: ro root=/dev/mapper/vg_lilith--raid-root
>> LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc
>> KEYTABLE=us ignore_loglevel earlyprintk=xen console=hvc0 rdshell
>> pcie_aspm=off
>> KERNEL supported cpus:
>> Intel GenuineIntel
>> AMD AuthenticAMD
>> Centaur CentaurHauls
>> xen_release_chunk: looking at area pfn bf790-bf79e: 14 pages freed
>> xen_release_chunk: looking at area pfn bf7e0-bf7ed: 13 pages freed
>> xen_release_chunk: looking at area pfn c0000-e0000: 131072 pages freed
>> xen_release_chunk: looking at area pfn f0000-fec00: 14977 pages freed
>> xen_release_chunk: looking at area pfn fec01-fed20: 0 pages freed
>> xen_release_chunk: looking at area pfn fed40-fee00: 0 pages freed
>> released 146076 pages of unused memory
>> BIOS-provided physical RAM map:
>> Xen: 0000000000000000 - 000000000009d800 (usable)
>> Xen: 000000000009d800 - 0000000000100000 (reserved)
>> Xen: 0000000000100000 - 00000000bf790000 (usable)
>> Xen: 00000000bf79e000 - 00000000bf7a0000 type 9
>> Xen: 00000000bf7a0000 - 00000000bf7ae000 (ACPI data)
>> Xen: 00000000bf7ae000 - 00000000bf7d0000 (ACPI NVS)
>> Xen: 00000000bf7d0000 - 00000000bf7e0000 (reserved)
>> Xen: 00000000bf7ed000 - 00000000c0000000 (reserved)
>> Xen: 00000000e0000000 - 00000000f0000000 (reserved)
>> Xen: 00000000fec00000 - 00000000fec01000 (reserved)
>> Xen: 00000000fed20000 - 00000000fed40000 (reserved)
>> Xen: 00000000fee00000 - 00000000fee01000 (reserved)
>> debug: ignoring loglevel setting.
>> bootconsole [xenboot0] enabled
>> DMI present.
>> last_pfn = 0xbf790 max_arch_pfn = 0x400000000
>> x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
>> initial memory mapped : 0 - 20000000
>> init_memory_mapping: 0000000000000000-00000000bf790000
>> 0000000000 - 00bf790000 page 4k
>> kernel direct mapping tables up to bf790000 @ 100000-700000
>> RAMDISK: 0218b000 - 02b69800
>> ACPI: RSDP 00000000000fa110 00024 (v02 ACPIAM)
>> ACPI: XSDT 00000000bf7a0100 00084 (v01 SMCI 20100225 MSFT
>> 00000097)
>> ACPI: FACP 00000000bf7a0290 000F4 (v04 022510 FACP1918 20100225 MSFT
>> 00000097)
>> ACPI: DSDT 00000000bf7a05f0 06C55 (v02 10605 10605000 00000000 INTL
>> 20051117)
>> ACPI: FACS 00000000bf7ae000 00040
>> ACPI: APIC 00000000bf7a0390 00092 (v02 022510 APIC1918 20100225 MSFT
>> 00000097)
>> ACPI: MCFG 00000000bf7a0430 0003C (v01 022510 OEMMCFG 20100225 MSFT
>> 00000097)
>> ACPI: OEMB 00000000bf7ae040 00073 (v01 022510 OEMB1918 20100225 MSFT
>> 00000097)
>> ACPI: HPET 00000000bf7aa5f0 00038 (v01 022510 OEMHPET 20100225 MSFT
>> 00000097)
>> ACPI: GSCI 00000000bf7ae0c0 02024 (v01 022510 GMCHSCI 20100225 MSFT
>> 00000097)
>> ACPI: 00000000bf7b00f0 00090 (v01 AMI OEMDMAR 00000001 MSFT
>> 00000097)
>> ACPI: SSDT 00000000bf7b1580 00363 (v01 DpgPmm CpuPm 00000012 INTL
>> 20051117)
>> ACPI: EINJ 00000000bf7aa630 00130 (v01 AMIER AMI_EINJ 20100225 MSFT
>> 00000097)
>> ACPI: BERT 00000000bf7aa7c0 00030 (v01 AMIER AMI_BERT 20100225 MSFT
>> 00000097)
>> ACPI: ERST 00000000bf7aa7f0 001B0 (v01 AMIER AMI_ERST 20100225 MSFT
>> 00000097)
>> ACPI: HEST 00000000bf7aa9a0 000A8 (v01 AMIER ABC_HEST 20100225 MSFT
>> 00000097)
>> ACPI: Local APIC address 0xfee00000
>> No NUMA configuration found
>> Faking a node at 0000000000000000-00000000bf790000
>> Bootmem setup node 0 0000000000000000-00000000bf790000
>> NODE_DATA [0000000000001000 - 0000000000005fff]
>> bootmap [0000000000008000 - 000000000001fef7] pages 18
>> (8 early reservations) ==> bootmem [0000000000 - 00bf790000]
>> #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 -
>> 0000001000]
>> #1 [0003309000 - 0003326000] XEN PAGETABLES ==> [0003309000 -
>> 0003326000]
>> #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 -
>> 0000008000]
>> #3 [0001000000 - 000216a048] TEXT DATA BSS ==> [0001000000 -
>> 000216a048]
>> #4 [000218b000 - 0002b69800] RAMDISK ==> [000218b000 -
>> 0002b69800]
>> #5 [0002b6a000 - 0003309000] XEN START INFO ==> [0002b6a000 -
>> 0003309000]
>> #6 [000216b000 - 000216b21b] BRK ==> [000216b000 -
>> 000216b21b]
>> #7 [0000100000 - 00006e0000] PGTABLE ==> [0000100000 -
>> 00006e0000]
>> found SMP MP-table at [ffff8800000ff780] ff780
>> Zone PFN ranges:
>> DMA 0x00000000 -> 0x00001000
>> DMA32 0x00001000 -> 0x00100000
>> Normal 0x00100000 -> 0x00100000
>> Movable zone start PFN for each node
>> early_node_map[2] active PFN ranges
>> 0: 0x00000000 -> 0x0000009d
>> 0: 0x00000100 -> 0x000bf790
>> On node 0 totalpages: 784173
>> DMA zone: 88 pages used for memmap
>> DMA zone: 1507 pages reserved
>> DMA zone: 2402 pages, LIFO batch:0
>> DMA32 zone: 16762 pages used for memmap
>> DMA32 zone: 763414 pages, LIFO batch:31
>> ACPI: PM-Timer IO Port: 0x808
>> ACPI: Local APIC address 0xfee00000
>> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
>> ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
>> ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
>> ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
>> ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled)
>> ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled)
>> ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled)
>> ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled)
>> ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
>> ACPI: IOAPIC (id[0x07] address[0xfec00000] gsi_base[0])
>> IOAPIC[0]: apic_id 7, version 0, address 0xfec00000, GSI 0-0
>> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
>> ERROR: Unable to locate IOAPIC for GSI 2
>> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
>> ERROR: Unable to locate IOAPIC for GSI 9
>> Using ACPI (MADT) for SMP configuration information
>> ACPI: HPET id: 0x8086a701 base: 0xfed00000
>> SMP: Allowing 4 CPUs, 0 hotplug CPUs
>> nr_irqs_gsi: 256
>> PM: Registered nosave memory: 000000000009d000 - 000000000009e000
>> PM: Registered nosave memory: 000000000009e000 - 0000000000100000
>> Allocating PCI resources starting at c0000000 (gap: c0000000:20000000)
>> Booting paravirtualized kernel on Xen
>> Xen version: 4.1-unstable (preserve-AD) (dom0)
>> NR_CPUS:16 nr_cpumask_bits:16 nr_cpu_ids:4 nr_node_ids:1
>> PERCPU: Embedded 28 pages/cpu @ffff88000336d000 s83096 r8192 d23400
>> u114688
>> pcpu-alloc: s83096 r8192 d23400 u114688 alloc=28*4096
>> pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
>> trying to map vcpu_info 0 at ffff880003378020, mfn 13b378, offset 32
>> cpu 0 using vcpu_info at ffff880003378020
>> trying to map vcpu_info 1 at ffff880003394020, mfn 13b394, offset 32
>> cpu 1 using vcpu_info at ffff880003394020
>> trying to map vcpu_info 2 at ffff8800033b0020, mfn 13b3b0, offset 32
>> cpu 2 using vcpu_info at ffff8800033b0020
>> trying to map vcpu_info 3 at ffff8800033cc020, mfn 13b3cc, offset 32
>> cpu 3 using vcpu_info at ffff8800033cc020
>> Xen: using vcpu_info placement
>> Built 1 zonelists in Node order, mobility grouping on. Total pages:
>> 765816
>> Policy zone: DMA32
>> Kernel command line: ro root=/dev/mapper/vg_lilith--raid-root
>> LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc
>> KEYTABLE=us ignore_loglevel earlyprintk=xen console=hvc0 rdshell
>> pcie_aspm=off
>> PCIe ASPM is disabled
>> PID hash table entries: 4096 (order: 3, 32768 bytes)
>> Initializing CPU#0
>> DMA: Placing 64MB software IO TLB between ffff88000794a000 -
>> ffff88000b94a000
>> DMA: software IO TLB at phys 0x794a000 - 0xb94a000
>> xen_swiotlb_fixup: buf=ffff88000794a000 size=67108864
>> xen_swiotlb_fixup: buf=ffff88000b9aa000 size=32768
>> Memory: 2960308k/3137088k available (4691k kernel code, 396k absent,
>> 176384k reserved, 2987k data, 656k init)
>> Hierarchical RCU implementation.
>> NR_IRQS:4352 nr_irqs:1280
>> xen: --> irq=0
>> xen: --> irq=1
>> xen: --> irq=2
>> xen: --> irq=3
>> xen: --> irq=4
>> xen: --> irq=5
>> xen: --> irq=6
>> xen: --> irq=7
>> xen: --> irq=8
>> xen: --> irq=9
>> xen: --> irq=10
>> xen: --> irq=11
>> xen: --> irq=12
>> xen: --> irq=13
>> xen: --> irq=14
>> xen: --> irq=15
>> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
>> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
>> xen: sci override: source_irq=9 global_irq=9 trigger=c polarity=1
>> xen: registering gsi 9 triggering 0 polarity 0
>> xen_allocate_pirq: returning irq 9 for gsi 9
>> xen: --> irq=9
>> xen: acpi sci 9
>> Console: colour VGA+ 80x25
>> console [hvc0] enabled, bootconsole disabled
>> console [hvc0] enabled, bootconsole disabled
>> Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
>> ... MAX_LOCKDEP_SUBCLASSES: 8
>> ... MAX_LOCK_DEPTH: 48
>> ... MAX_LOCKDEP_KEYS: 8191
>> ... CLASSHASH_SIZE: 4096
>> ... MAX_LOCKDEP_ENTRIES: 16384
>> ... MAX_LOCKDEP_CHAINS: 32768
>> ... CHAINHASH_SIZE: 16384
>> memory used by lock dependency info: 5855 kB
>> per task-struct memory footprint: 1920 bytes
>> Xen: using vcpuop timer interface
>> installing Xen timer for CPU 0
>> alloc irq_desc for 1279 on node 0
>> alloc kstat_irqs on node 0
>> Detected 2400.066 MHz processor.
>> Calibrating delay loop (skipped), value calculated using timer
>> frequency.. 4800.13 BogoMIPS (lpj=2400066)
>> Security Framework initialized
>> SELinux: Initializing.
>> SELinux: Starting in permissive mode
>> Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
>> Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
>> Mount-cache hash table entries: 256
>> Initializing cgroup subsys ns
>> Initializing cgroup subsys cpuacct
>> CPU: L1 I cache: 32K, L1 D cache: 32K
>> CPU: L2 cache: 256K
>> CPU: L3 cache: 8192K
>> CPU 0/0x0 -> Node 0
>> CPU: Unsupported number of siblings 16
>> Performance Events: unsupported p6 CPU model 30 no PMU driver,
>> software events only.
>> lockdep: fixing up alternatives.
>> SMP alternatives: switching to UP code
>> ACPI: Core revision 20090903
>> alloc irq_desc for 1278 on node 0
>> alloc kstat_irqs on node 0
>> cpu 0 spinlock event irq 1278
>> alloc irq_desc for 1277 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1276 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1275 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1274 on node 0
>> alloc kstat_irqs on node 0
>> installing Xen timer for CPU 1
>> alloc irq_desc for 1273 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1272 on node 0
>> alloc kstat_irqs on node 0
>> cpu 1 spinlock event irq 1272
>> lockdep: fixing up alternatives.
>> SMP alternatives: switching to SMP code
>> alloc irq_desc for 1271 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1270 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1269 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1268 on node 0
>> alloc kstat_irqs on node 0
>> Initializing CPU#1
>> CPU: L1 I cache: 32K, L1 D cache: 32K
>> CPU: L2 cache: 256K
>> CPU: L3 cache: 8192K
>> CPU 1/0x0 -> Node 0
>> CPU: Unsupported number of siblings 16
>> installing Xen timer for CPU 2
>> alloc irq_desc for 1267 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1266 on node 0
>> alloc kstat_irqs on node 0
>> cpu 2 spinlock event irq 1266
>> alloc irq_desc for 1265 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1264 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1263 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1262 on node 0
>> alloc kstat_irqs on node 0
>> Initializing CPU#2
>> CPU: L1 I cache: 32K, L1 D cache: 32K
>> CPU: L2 cache: 256K
>> CPU: L3 cache: 8192K
>> CPU 2/0x0 -> Node 0
>> CPU: Unsupported number of siblings 16
>> installing Xen timer for CPU 3
>> alloc irq_desc for 1261 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1260 on node 0
>> alloc kstat_irqs on node 0
>> cpu 3 spinlock event irq 1260
>> alloc irq_desc for 1259 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1258 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1257 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1256 on node 0
>> alloc kstat_irqs on node 0
>> Initializing CPU#3
>> CPU: L1 I cache: 32K, L1 D cache: 32K
>> CPU: L2 cache: 256K
>> CPU: L3 cache: 8192K
>> CPU 3/0x0 -> Node 0
>> CPU: Unsupported number of siblings 16
>> Brought up 4 CPUs
>> Grant table initialized
>> Time: 16:42:50 Date: 04/07/10
>> NET: Registered protocol family 16
>> alloc irq_desc for 1255 on node 0
>> alloc kstat_irqs on node 0
>> ACPI: bus type pci registered
>> PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
>> PCI: MCFG area at e0000000 reserved in E820
>> PCI: Using MMCONFIG at e0000000 - efffffff
>> PCI: Using configuration type 1 for base access
>> bio: create slab<bio-0> at 0
>> ERROR: Unable to locate IOAPIC for GSI 9
>> ACPI: EC: Look up EC in DSDT
>> ACPI Warning for \_SB_._OSC: Return type mismatch - found Integer,
>> expected Buffer (20090903/nspredef-1006)
>> \_SB_:_OSC evaluation returned wrong type
>> _OSC request data:1 6
>> ACPI: Executed 1 blocks of module-level executable AML code
>> ACPI: Interpreter enabled
>> ACPI: (supports S0 S1 S4 S5)
>> ACPI: Using IOAPIC for interrupt routing
>> ACPI Warning: Incorrect checksum in table [OEMB] - 91, should be 8E
>> (20090903/tbutils-314)
>> ACPI Warning: Incorrect checksum in table [ ] - 7B, should be BF
>> (20090903/tbutils-314)
>> ACPI: No dock devices found.
>> ACPI: PCI Root Bridge [PCI0] (0000:00)
>> pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
>> pci 0000:00:03.0: PME# disabled
>> pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
>> pci 0000:00:05.0: PME# disabled
>> pci 0000:00:1a.0: reg 10 32bit mmio: [0xfb3fc000-0xfb3fc3ff]
>> pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
>> pci 0000:00:1a.0: PME# disabled
>> pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
>> pci 0000:00:1c.0: PME# disabled
>> pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
>> pci 0000:00:1c.4: PME# disabled
>> pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
>> pci 0000:00:1c.5: PME# disabled
>> pci 0000:00:1d.0: reg 10 32bit mmio: [0xfb3fa000-0xfb3fa3ff]
>> pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
>> pci 0000:00:1d.0: PME# disabled
>> pci 0000:00:1f.2: reg 10 io port: [0xb400-0xb407]
>> pci 0000:00:1f.2: reg 14 io port: [0xbc00-0xbc03]
>> pci 0000:00:1f.2: reg 18 io port: [0xb880-0xb887]
>> pci 0000:00:1f.2: reg 1c io port: [0xb800-0xb803]
>> pci 0000:00:1f.2: reg 20 io port: [0xb480-0xb49f]
>> pci 0000:00:1f.2: reg 24 32bit mmio: [0xfb3f8000-0xfb3f87ff]
>> pci 0000:00:1f.2: PME# supported from D3hot
>> pci 0000:00:1f.2: PME# disabled
>> pci 0000:00:1f.3: reg 10 64bit mmio: [0xfb3f6000-0xfb3f60ff]
>> pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
>> pci 0000:03:00.0: reg 10 32bit mmio: [0xfb420000-0xfb43ffff]
>> pci 0000:03:00.0: reg 14 32bit mmio: [0xfb480000-0xfb4fffff]
>> pci 0000:03:00.0: reg 18 io port: [0xcc00-0xcc1f]
>> pci 0000:03:00.0: reg 1c 32bit mmio: [0xfb41c000-0xfb41ffff]
>> pci 0000:03:00.0: reg 30 32bit mmio pref: [0xfb440000-0xfb47ffff]
>> pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
>> pci 0000:03:00.0: PME# disabled
>> pci 0000:00:1c.0: bridge io port: [0xc000-0xcfff]
>> pci 0000:00:1c.0: bridge 32bit mmio: [0xfb400000-0xfb4fffff]
>> pci 0000:04:00.0: reg 10 32bit mmio: [0xfb5e0000-0xfb5fffff]
>> pci 0000:04:00.0: reg 18 io port: [0xdc00-0xdc1f]
>> pci 0000:04:00.0: reg 1c 32bit mmio: [0xfb5dc000-0xfb5dffff]
>> pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
>> pci 0000:04:00.0: PME# disabled
>> pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff]
>> pci 0000:00:1c.4: bridge 32bit mmio: [0xfb500000-0xfb5fffff]
>> pci 0000:05:00.0: reg 10 32bit mmio: [0xfb6e0000-0xfb6fffff]
>> pci 0000:05:00.0: reg 18 io port: [0xec00-0xec1f]
>> pci 0000:05:00.0: reg 1c 32bit mmio: [0xfb6dc000-0xfb6dffff]
>> pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
>> pci 0000:05:00.0: PME# disabled
>> pci 0000:00:1c.5: bridge io port: [0xe000-0xefff]
>> pci 0000:00:1c.5: bridge 32bit mmio: [0xfb600000-0xfb6fffff]
>> pci 0000:06:03.0: reg 10 32bit mmio pref: [0xfa000000-0xfaffffff]
>> pci 0000:06:03.0: reg 14 32bit mmio: [0xfb7fc000-0xfb7fffff]
>> pci 0000:06:03.0: reg 18 32bit mmio: [0xfb800000-0xfbffffff]
>> pci 0000:00:1e.0: transparent bridge
>> pci 0000:00:1e.0: bridge 32bit mmio: [0xfb700000-0xfbffffff]
>> pci 0000:00:1e.0: bridge 64bit mmio pref: [0xfa000000-0xfaffffff]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR1E._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR20._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR24._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR25._PRT]
>> (XEN) PCI add device 00:00.0
>> (XEN) PCI add device 00:03.0
>> (XEN) PCI add device 00:05.0
>> (XEN) PCI add device 00:08.0
>> (XEN) PCI add device 00:08.1
>> (XEN) PCI add device 00:08.2
>> (XEN) PCI add device 00:08.3
>> (XEN) PCI add device 00:10.0
>> (XEN) PCI add device 00:10.1
>> (XEN) PCI add device 00:1a.0
>> (XEN) PCI add device 00:1c.0
>> (XEN) PCI add device 00:1c.4
>> (XEN) PCI add device 00:1c.5
>> (XEN) PCI add device 00:1d.0
>> (XEN) PCI add device 00:1e.0
>> (XEN) PCI add device 00:1f.0
>> (XEN) PCI add device 00:1f.2
>> (XEN) PCI add device 00:1f.3
>> (XEN) PCI add device 03:00.0
>> (XEN) PCI add device 04:00.0
>> (XEN) PCI add device 05:00.0
>> (XEN) PCI add device 06:03.0
>> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12 14 15)
>> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12 14 15)
>> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12 14 15)
>> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12 *14 15)
>> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 14 15) *0,
>> disabled.
>> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 *7 10 11 12 14 15)
>> ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 7 10 11 12 14 15) *0,
>> disabled.
>> ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 6 7 10 11 12 14 *15)
>> sync cpu 0 get result 1 max_id 3
>> sync cpu 1 get result 1 max_id 3
>> sync cpu 2 get result 1 max_id 3
>> sync cpu 3 get result 1 max_id 3
>> alloc irq_desc for 1254 on node 0
>> alloc kstat_irqs on node 0
>> xen_balloon: Initialising balloon driver with page order 0.
>> vgaarb: device added:
>> PCI:0000:06:03.0,decodes=io+mem,owns=io+mem,locks=none
>> vgaarb: loaded
>> SCSI subsystem initialized
>> libata version 3.00 loaded.
>> usbcore: registered new interface driver usbfs
>> usbcore: registered new interface driver hub
>> usbcore: registered new device driver usb
>> PCI: Using ACPI for IRQ routing
>> NetLabel: Initializing
>> NetLabel: domain hash size = 128
>> NetLabel: protocols = UNLABELED CIPSOv4
>> NetLabel: unlabeled traffic allowed by default
>> Switching to clocksource xen
>> pnp: PnP ACPI init
>> ACPI: bus type pnp registered
>> xen: registering gsi 8 triggering 1 polarity 0
>> xen_allocate_pirq: returning irq 8 for gsi 8
>> xen:scsi0 : ahci
>> scsi1 : ahci
>> scsi2 : ahci
>> scsi3 : ahci
>> scsi4 : ahci
>> scsi5 : ahci
>> ata1: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8100 irq 1247
>> ata2: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8180 irq 1247
>> ata3: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8200 irq 1247
>> ata4: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8280 irq 1247
>> ata5: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8300 irq 1247
>> ata6: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8380 irq 1247
>> usb 1-1: udev 2, busnum 1, minor = 1
>> usb 1-1: New USB device found, idVendor=8087, idProduct=0020
>> usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
>> usb 1-1: usb_probe_device
>> usb 1-1: configuration #1 chosen from 1 choice
>> usb 1-1: adding 1-1:1.0 (config #1, interface 0)
>> hub 1-1:1.0: usb_probe_interface
>> hub 1-1:1.0: usb_probe_interface - got id
>> hub 1-1:1.0: USB hub found
>> hub 1-1:1.0: 6 ports detected
>> hub 1-1:1.0: standalone hub
>> hub 1-1:1.0: individual port power switching
>> hub 1-1:1.0: individual port over-current protection
>> hub 1-1:1.0: Single TT
>> hub 1-1:1.0: TT requires at most 8 FS bit times (666 ns)
>> hub 1-1:1.0: Port indicators are supported
>> hub 1-1:1.0: power on to power good time: 100ms
>> hub 1-1:1.0: local power source is good
>> hub 1-1:1.0: enabling power on all ports
>> hub 2-0:1.0: state 7 ports 2 chg 0002 evt 0000
>> hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
>> ehci_hcd 0000:00:1d.0: port 1 high speed
>> ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 POWER sig=se0
>> PE CONNECT
>> hub 1-1:1.0: port 2: status 0101 change 0001
>> usb 2-1: new high speed USB device using ehci_hcd and address 2
>> ehci_hcd 0000:00:1d.0: port 1 high speed
>> ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 POWER sig=se0
>> PE CONNECT
>> usb 1-1: link qh256-0001/ffff8800bcd9ab40 start 1 [1/0 us]
>> usb 2-1: udev 2, busnum 2, minor = 129
>> usb 2-1: New USB device found, idVendor=8087, idProduct=0020
>> usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
>> usb 2-1: usb_probe_device
>> usb 2-1: configuration #1 chosen from 1 choice
>> usb 2-1: adding 2-1:1.0 (config #1, interface 0)
>> hub 2-1:1.0: usb_probe_interface
>> hub 2-1:1.0: usb_probe_interface - got id
>> hub 2-1:1.0: USB hub found
>> hub 2-1:1.0: 8 ports detected
>> hub 2-1:1.0: standalone hub
>> hub 2-1:1.0: individual port power switching
>> hub 2-1:1.0: individual port over-current protection
>> hub 2-1:1.0: Single TT
>> hub 2-1:1.0: TT requires at most 8 FS bit times (666 ns)
>> hub 2-1:1.0: Port indicators are supported
>> hub 2-1:1.0: power on to power good time: 100ms
>> hub 2-1:1.0: local power source is good
>> hub 2-1:1.0: enabling power on all ports
>> hub 1-1:1.0: state 7 ports 6 chg 0004 evt 0000
>> hub 1-1:1.0: port 2, status 0101, change 0000, 12 Mb/s
>> usb 1-1.2: new full speed USB device using ehci_hcd and address 3
>> hub 1-1:1.0: port 2 not reset yet, waiting 10ms
>> ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata1.00: ATA-8: WDC WD10EADS-00P8B0, 01.00A01, max UDMA/133
>> ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
>> ata1.00: configured for UDMA/133
>> scsi 0:0:0:0: Direct-Access ATA WDC WD10EADS-00P 01.0 PQ: 0
>> ANSI: 5
>> sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
>> sd 0:0:0:0: [sda] Write Protect is off
>> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
>> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
>> support DPO or FUA
>> sd 0:0:0:0: Attached scsi generic sg0 type 0
>> sda:
>> usb 2-1: link qh256-0001/ffff8800be450cc0 start 1 [1/0 us]
>> sda1 sda2 sda3 sda4
>> sd 0:0:0:0: [sda] Attached SCSI disk
>> usb 1-1.2: skipped 1 descriptor after interface
>> usb 1-1.2: skipped 1 descriptor after interface
>> usb 1-1.2: default language 0x0409
>> usb 1-1.2: udev 3, busnum 1, minor = 2
>> usb 1-1.2: New USB device found, idVendor=0557, idProduct=2221
>> usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
>> usb 1-1.2: Product: Hermon USB hidmouse Device
>> usb 1-1.2: Manufacturer: Winbond Electronics Corp
>> usb 1-1.2: usb_probe_device
>> usb 1-1.2: configuration #1 chosen from 1 choice
>> usb 1-1.2: adding 1-1.2:1.0 (config #1, interface 0)
>> usbhid 1-1.2:1.0: usb_probe_interface
>> usbhid 1-1.2:1.0: usb_probe_interface - got id
>> input: Winbond Electronics Corp Hermon USB hidmouse Device as
>> /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input4
>> generic-usb 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse
>> [Winbond Electronics Corp Hermon USB hidmouse Device] on
>> usb-0000:00:1a.0-1.2/input0
>> usb 1-1.2: adding 1-1.2:1.1 (config #1, interface 1)
>> usbhid 1-1.2:1.1: usb_probe_interface
>> usbhid 1-1.2:1.1: usb_probe_interface - got id
>> input: Winbond Electronics Corp Hermon USB hidmouse Device as
>> /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.1/input/input5
>> usb 1-1.2: link qh8-0601/ffff8800bc52e440 start 2 [1/2 us]
>> generic-usb 0003:0557:2221.0002: input,hidraw1: USB HID v1.00
>> Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on
>> usb-0000:00:1a.0-1.2/input1
>> hub 2-1:1.0: state 7 ports 8 chg 0000 evt 0000
>> hub 1-1:1.0: state 7 ports 6 chg 0000 evt 0004
>> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata2.00: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
>> ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
>> ata2.00: configured for UDMA/133
>> scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0
>> ANSI: 5
>> sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
>> sd 1:0:0:0: Attached scsi generic sg1 type 0
>> sd 1:0:0:0: [sdb] Write Protect is off
>> sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
>> sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't
>> support DPO or FUA
>> sdb: sdb1 sdb2 sdb3 sdb4
>> sd 1:0:0:0: [sdb] Attached SCSI disk
>> input: ImExPS/2 Generic Explorer Mouse as
>> /devices/platform/i8042/serio1/input/input6
>> ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata3.00: ATA-8: WDC WD10EADS-00P8B0, 01.00A01, max UDMA/133
>> ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
>> ata3.00: configured for UDMA/133
>> scsi 2:0:0:0: Direct-Access ATA WDC WD10EADS-00P 01.0 PQ: 0
>> ANSI: 5
>> sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
>> sd 2:0:0:0: Attached scsi generic sg2 type 0
>> sd 2:0:0:0: [sdc] Write Protect is off
>> sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
>> sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't
>> support DPO or FUA
>> sdc: sdc1 sdc2 sdc3 sdc4
>> sd 2:0:0:0: [sdc] Attached SCSI disk
>> hub 2-1:1.0: hub_suspend
>> usb 2-1: unlink qh256-0001/ffff8800be450cc0 start 1 [1/0 us]
>> usb 2-1: usb auto-suspend
>> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata4.00: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
>> ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
>> ata4.00: configured for UDMA/133
>> scsi 3:0:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0
>> ANSI: 5
>> sd 3:0:0:0: [sdd] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
>> sd 3:0:0:0: Attached scsi generic sg3 type 0
>> sd 3:0:0:0: [sdd] Write Protect is off
>> sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
>> sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't
>> support DPO or FUA
>> sdd: sdd1 sdd2 sdd3 sdd4
>> sd 3:0:0:0: [sdd] Attached SCSI disk
>> ata5: SATA link down (SStatus 0 SControl 300)
>> ata6: SATA link down (SStatus 0 SControl 300)
>> md: raid10 personality registered for level 10
>> Intel AES-NI instructions are not detected.
>> md: md0 stopped.
>> md: bind<sdb3>
>> md: bind<sdc3>
>> md: bind<sdd3>
>> md: bind<sda3>
>> raid10: md0 is not clean -- starting background reconstruction
>> raid10: raid set md0 active with 4 out of 4 devices
>> md0: detected capacity change from 0 to 838860668928
>> md: resync of RAID array md0
>> md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
>> md: using maximum available idle IO bandwidth (but not more than
>> 200000 KB/sec) for resync.
>> md: using 128k window, over a total of 819199872 blocks.
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2]
>> fault addr bf579000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf579
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 179
>> (XEN) l1[179] = 0
>> (XEN) l1[179] not present
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2]
>> fault addr bf579000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf579
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 179
>> (XEN) l1[179] = 0
>> (XEN) l1[179] not present
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2]
>> fault addr bf578000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf578
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 178
>> (XEN) l1[178] = 0
>> (XEN) l1[178] not present
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2]
>> fault addr bf578000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf578
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 178
>> (XEN) l1[178] = 0
>> (XEN) l1[178] not present
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2]
>> fault addr bf57b000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf57b
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 17b
>> (XEN) l1[17b] = 0
>> (XEN) l1[17b] not present
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2]
>> fault addr bf57b000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf57b
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 17b
>> (XEN) l1[17b] = 0
>> (XEN) l1[17b] not present
>> md0:(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2]
>> fault addr bf57b000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf57b
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 17b
>> (XEN) l1[17b] = 0
>> (XEN) l1[17b] not present
>>
>> ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
>> ata2.00: irq_stat 0x20000000, host bus error
>> ata2: SError: { HostInt }
>> ata2.00: failed command: WRITE FPDMA QUEUED
>> ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
>> res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata2.00: status: { DRDY }
>> ata2: hard resetting link
>> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata2.00: configured for UDMA/133
>> ata2: EH complete
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2]
>> fault addr bf57b000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf57b
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 17b
>> (XEN) l1[17b] = 0
>> (XEN) l1[17b] not present
>> ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
>> ata2.00: irq_stat 0x20000000, host bus error
>> ata2: SError: { HostInt }
>> ata2.00: failed command: WRITE FPDMA QUEUED
>> ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
>> res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata2.00: status: { DRDY }
>> ata2: hard resetting link
>> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata2.00: configured for UDMA/133
>> ata2: EH complete
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2]
>> fault addr bf57b000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf57b
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 17b
>> (XEN) l1[17b] = 0
>> (XEN) l1[17b] not present
>> ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
>> ata2.00: irq_stat 0x20000000, host bus error
>> ata2: SError: { HostInt }
>> ata2.00: failed command: WRITE FPDMA QUEUED
>> ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
>> res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata2.00: status: { DRDY }
>> ata2: hard resetting link
>> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata2.00: configured for UDMA/133
>> ata2: EH complete
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2]
>> fault addr bf57b000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf57b
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 17b
>> (XEN) l1[17b] = 0
>> (XEN) l1[17b] not present
>> ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
>> ata2.00: irq_stat 0x20000000, host bus error
>> ata2: SError: { HostInt }
>> ata2.00: failed command: WRITE FPDMA QUEUED
>> ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
>> res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata2.00: status: { DRDY }
>> ata2: hard resetting link
>> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata2.00: configured for UDMA/133
>> ata2: EH complete
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2]
>> fault addr bf57b000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf57b
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 17b
>> (XEN) l1[17b] = 0
>> (XEN) l1[17b] not present
>> ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
>> ata2.00: irq_stat 0x20000000, host bus error
>> ata2: SError: { HostInt }
>> ata2.00: failed command: WRITE FPDMA QUEUED
>> ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
>> res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata2.00: status: { DRDY }
>> ata2: hard resetting link
>> hub 2-0:1.0: hub_suspend
>> usb usb2: bus auto-suspend
>> ehci_hcd 0000:00:1d.0: suspend root hub
>> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata2.00: configured for UDMA/133
>> ata2: EH complete
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2]
>> fault addr bf57b000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf57b
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 17b
>> (XEN) l1[17b] = 0
>> (XEN) l1[17b] not present
>> ata2.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
>> ata2.00: irq_stat 0x20000000, host bus error
>> ata2: SError: { HostInt }
>> ata2.00: failed command: WRITE FPDMA QUEUED
>> ata2.00: cmd 61/80:00:c3:aa:a0/00:00:0c:00:00/40 tag 0 ncq 65536 out
>> res 40/00:04:c3:aa:a0/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata2.00: status: { DRDY }
>> ata2: hard resetting link
>> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata2.00: configured for UDMA/133
>> sd 1:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
>> sd 1:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor]
>> Descriptor sense data with sense descriptors (in hex):
>> 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
>> 0c a0 aa c3
>> sd 1:0:0:0: [sdb] Add. Sense: No additional sense information
>> sd 1:0:0:0: [sdb] CDB: Write(10): 2a 00 0c a0 aa c3 00 00 80 00
>> end_request: I/O error, dev sdb, sector 211856067
>> raid10: Disk failure on sdb3, disabling device.
>> raid10: Operation continuing on 3 devices.
>> ata2: EH complete
>> unknown partition table
>> md: md0: resync done.
>> md: checkpointing resync of md0.
>> RAID10 conf printout:
>> --- wd:3 rd:4
>> disk 0, wo:0, o:1, dev:sda3
>> disk 1, wo:1, o:0, dev:sdb3
>> disk 2, wo:0, o:1, dev:sdc3
>> disk 3, wo:0, o:1, dev:sdd3
>> RAID10 conf printout:
>> --- wd:3 rd:4
>> disk 0, wo:0, o:1, dev:sda3
>> disk 2, wo:0, o:1, dev:sdc3
>> disk 3, wo:0, o:1, dev:sdd3
>> md: resync of RAID array md0
>> md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
>> md: using maximum available idle IO bandwidth (but not more than
>> 200000 KB/sec) for resync.
>> md: using 128k window, over a total of 819199872 blocks.
>> md: resuming resync of md0 from checkpoint.
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2]
>> fault addr bf578000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf578
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 178
>> (XEN) l1[178] = 0
>> (XEN) l1[178] not present
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2]
>> fault addr bf579000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf579
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 179
>> (XEN) l1[179] = 0
>> (XEN) l1[179] not present
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2]
>> fault addr bf57b000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf57b
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 17b
>> (XEN) l1[17b] = 0
>> (XEN) l1[17b] not present
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [00:1f.2]
>> fault addr bf57b000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 05h] PTE Write access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf57b
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 17b
>> (XEN) l1[17b] = 0
>> (XEN) l1[17b] not present
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2]
>> fault addr bf57b000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf57b
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 17b
>> (XEN) l1[17b] = 0
>> (XEN) l1[17b] not present
>> ata4.00: exception Emask 0x60 SAct 0x1 SErr 0x800 action 0x6 frozen
>> ata4.00: irq_stat 0x20000000, host bus error
>> ata4: SError: { HostInt }
>> ata4.00: failed command: WRITE FPDMA QUEUED
>> ata4.00: cmd 61/80:00:43:b2:a1/00:00:0c:00:00/40 tag 0 ncq 65536 out
>> res 40/00:04:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4: hard resetting link
>> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata4.00: configured for UDMA/133
>> ata4: EH complete
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2]
>> fault addr bf578000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf578
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 178
>> (XEN) l1[178] = 0
>> (XEN) l1[178] not present
>> ata4.00: exception Emask 0x60 SAct 0x3 SErr 0x800 action 0x6 frozen
>> ata4.00: irq_stat 0x20000000, host bus error
>> ata4: SError: { HostInt }
>> ata4.00: failed command: WRITE FPDMA QUEUED
>> ata4.00: cmd 61/80:00:43:b2:a1/00:00:0c:00:00/40 tag 0 ncq 65536 out
>> res 40/00:0c:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: WRITE FPDMA QUEUED
>> ata4.00: cmd 61/80:08:43:b1:a1/00:00:0c:00:00/40 tag 1 ncq 65536 out
>> res 40/00:0c:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4: hard resetting link
>> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata4.00: configured for UDMA/133
>> ata4: EH complete
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2]
>> fault addr bf578000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf578
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 178
>> (XEN) l1[178] = 0
>> (XEN) l1[178] not present
>> ata4.00: exception Emask 0x60 SAct 0x3 SErr 0x800 action 0x6 frozen
>> ata4.00: irq_stat 0x20000000, host bus error
>> ata4: SError: { HostInt }
>> ata4.00: failed command: WRITE FPDMA QUEUED
>> ata4.00: cmd 61/80:00:43:b1:a1/00:00:0c:00:00/40 tag 0 ncq 65536 out
>> res 40/00:0c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: WRITE FPDMA QUEUED
>> ata4.00: cmd 61/80:08:43:b2:a1/00:00:0c:00:00/40 tag 1 ncq 65536 out
>> res 40/00:0c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4: hard resetting link
>> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata4.00: configured for UDMA/133
>> ata4: EH complete
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2]
>> fault addr bf578000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf578
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 178
>> (XEN) l1[178] = 0
>> (XEN) l1[178] not present
>> ata4.00: exception Emask 0x60 SAct 0x3f SErr 0x800 action 0x6 frozen
>> ata4.00: irq_stat 0x20000000, host bus error
>> ata4: SError: { HostInt }
>> ata4.00: failed command: WRITE FPDMA QUEUED
>> ata4.00: cmd 61/80:00:43:b2:a1/00:00:0c:00:00/40 tag 0 ncq 65536 out
>> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: WRITE FPDMA QUEUED
>> ata4.00: cmd 61/80:08:43:b1:a1/00:00:0c:00:00/40 tag 1 ncq 65536 out
>> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: READ FPDMA QUEUED
>> ata4.00: cmd 60/00:10:43:2d:a2/04:00:0c:00:00/40 tag 2 ncq 524288 in
>> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: READ FPDMA QUEUED
>> ata4.00: cmd 60/00:18:43:31:a2/04:00:0c:00:00/40 tag 3 ncq 524288 in
>> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: READ FPDMA QUEUED
>> ata4.00: cmd 60/00:20:43:35:a2/04:00:0c:00:00/40 tag 4 ncq 524288 in
>> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: READ FPDMA QUEUED
>> ata4.00: cmd 60/00:28:43:39:a2/04:00:0c:00:00/40 tag 5 ncq 524288 in
>> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4: hard resetting link
>> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata4.00: configured for UDMA/133
>> ata4: EH complete
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2]
>> fault addr bf578000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf578
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 178
>> (XEN) l1[178] = 0
>> (XEN) l1[178] not present
>> ata4.00: exception Emask 0x60 SAct 0x3f SErr 0x800 action 0x6 frozen
>> ata4.00: irq_stat 0x20000000, host bus error
>> ata4: SError: { HostInt }
>> ata4.00: failed command: READ FPDMA QUEUED
>> ata4.00: cmd 60/00:00:43:39:a2/04:00:0c:00:00/40 tag 0 ncq 524288 in
>> res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: READ FPDMA QUEUED
>> ata4.00: cmd 60/00:08:43:35:a2/04:00:0c:00:00/40 tag 1 ncq 524288 in
>> res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: READ FPDMA QUEUED
>> ata4.00: cmd 60/00:10:43:31:a2/04:00:0c:00:00/40 tag 2 ncq 524288 in
>> res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: READ FPDMA QUEUED
>> ata4.00: cmd 60/00:18:43:2d:a2/04:00:0c:00:00/40 tag 3 ncq 524288 in
>> res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: WRITE FPDMA QUEUED
>> ata4.00: cmd 61/80:20:43:b1:a1/00:00:0c:00:00/40 tag 4 ncq 65536 out
>> res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: WRITE FPDMA QUEUED
>> ata4.00: cmd 61/80:28:43:b2:a1/00:00:0c:00:00/40 tag 5 ncq 65536 out
>> res 40/00:2c:43:b2:a1/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4: hard resetting link
>> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata4.00: configured for UDMA/133
>> ata4: EH complete
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2]
>> fault addr bf578000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf578
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 178
>> (XEN) l1[178] = 0
>> (XEN) l1[178] not present
>> ata4.00: exception Emask 0x60 SAct 0x3f SErr 0x800 action 0x6 frozen
>> ata4.00: irq_stat 0x20000000, host bus error
>> ata4: SError: { HostInt }
>> ata4.00: failed command: WRITE FPDMA QUEUED
>> ata4.00: cmd 61/80:00:43:b2:a1/00:00:0c:00:00/40 tag 0 ncq 65536 out
>> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: WRITE FPDMA QUEUED
>> ata4.00: cmd 61/80:08:43:b1:a1/00:00:0c:00:00/40 tag 1 ncq 65536 out
>> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: READ FPDMA QUEUED
>> ata4.00: cmd 60/00:10:43:2d:a2/04:00:0c:00:00/40 tag 2 ncq 524288 in
>> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: READ FPDMA QUEUED
>> ata4.00: cmd 60/00:18:43:31:a2/04:00:0c:00:00/40 tag 3 ncq 524288 in
>> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: READ FPDMA QUEUED
>> ata4.00: cmd 60/00:20:43:35:a2/04:00:0c:00:00/40 tag 4 ncq 524288 in
>> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: READ FPDMA QUEUED
>> ata4.00: cmd 60/00:28:43:39:a2/04:00:0c:00:00/40 tag 5 ncq 524288 in
>> res 40/00:2c:43:39:a2/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4: hard resetting link
>> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata4.00: configured for UDMA/133
>> sd 3:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
>> sd 3:0:0:0: [sdd] Sense Key : Aborted Command [current] [descriptor]
>> Descriptor sense data with sense descriptors (in hex):
>> 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
>> 0c a2 39 43
>> sd 3:0:0:0: [sdd] Add. Sense: No additional sense information
>> sd 3:0:0:0: [sdd] CDB: Write(10): 2a 00 0c a1 b2 43 00 00 80 00
>> end_request: I/O error, dev sdd, sector 211923523
>> raid10: Disk failure on sdd3, disabling device.
>> raid10: Operation continuing on 2 devices.
>> ata4: EH complete
>> md: md0: resync done.
>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Read] Request device [00:1f.2]
>> fault addr bf578000, iommu reg = ffff82c3fff57000
>> (XEN) DMAR:[fault reason 06h] PTE Read access is not set
>> (XEN) print_vtd_entries: iommu = ffff83013fff3e80 bdf = 0:1f.2 gmfn =
>> bf578
>> (XEN) root_entry = ffff83013ff36000
>> (XEN) root_entry[0] = 13c6bb001
>> (XEN) context = ffff83013c6bb000
>> (XEN) context[fa] = 2_13fec4001
>> (XEN) l4 = ffff83013fec4000
>> (XEN) l4_index = 0
>> (XEN) l4[0] = 13fec1003
>> (XEN) l3 = ffff83013fec1000
>> (XEN) l3_index = 2
>> (XEN) l3[2] = 13ccbe003
>> (XEN) l2 = ffff83013ccbe000
>> (XEN) l2_index = 1fa
>> (XEN) l2[1fa] = 13cac3003
>> (XEN) l1 = ffff83013cac3000
>> (XEN) l1_index = 178
>> (XEN) l1[178] = 0
>> (XEN) l1[178] not present
>> ata4.00: exception Emask 0x60 SAct 0x1f SErr 0x800 action 0x6 frozen
>> ata4.00: irq_stat 0x20000000, host bus error
>> ata4: SError: { HostInt }
>> ata4.00: failed command: READ FPDMA QUEUED
>> ata4.00: cmd 60/00:00:43:39:a2/04:00:0c:00:00/40 tag 0 ncq 524288 in
>> res 40/00:24:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: READ FPDMA QUEUED
>> ata4.00: cmd 60/00:08:43:35:a2/04:00:0c:00:00/40 tag 1 ncq 524288 in
>> res 40/00:24:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: READ FPDMA QUEUED
>> ata4.00: cmd 60/00:10:43:31:a2/04:00:0c:00:00/40 tag 2 ncq 524288 in
>> res 40/00:24:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: READ FPDMA QUEUED
>> ata4.00: cmd 60/00:18:43:2d:a2/04:00:0c:00:00/40 tag 3 ncq 524288 in
>> res 40/00:24:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4.00: failed command: WRITE FPDMA QUEUED
>> ata4.00: cmd 61/80:20:43:b1:a1/00:00:0c:00:00/40 tag 4 ncq 65536 out
>> res 40/00:24:43:b1:a1/00:00:0c:00:00/40 Emask 0x60 (host
>> bus error)
>> ata4.00: status: { DRDY }
>> ata4: hard resetting link
>> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata4.00: configured for UDMA/133
>> sd 3:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
>> sd 3:0:0:0: [sdd] Sense Key : Aborted Command [current] [descriptor]
>> Descriptor sense data with sense descriptors (in hex):
>> 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
>> 0c a1 b1 43
>> sd 3:0:0:0: [sdd] Add. Sense: No additional sense information
>> sd 3:0:0:0: [sdd] CDB: Write(10): 2a 00 0c a1 b1 43 00 00 80 00
>> end_request: I/O error, dev sdd, sector 211923267
>> ata4: EH complete
>> md: checkpointing resync of md0.
>> RAID10 conf printout:
>> --- wd:2 rd:4
>> disk 0, wo:0, o:1, dev:sda3
>> disk 2, wo:0, o:1, dev:sdc3
>> disk 3, wo:1, o:0, dev:sdd3
>> RAID10 conf printout:
>> --- wd:2 rd:4
>> disk 0, wo:0, o:1, dev:sda3
>> disk 2, wo:0, o:1, dev:sdc3
>> md: resync of RAID array md0
>> md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
>> md: using maximum available idle IO bandwidth (but not more than
>> 200000 KB/sec) for resync.
>> md: using 128k window, over a total of 819199872 blocks.
>> md: resuming resync of md0 from checkpoint.
>> md: md0: resync done.
>> RAID10 conf printout:
>> --- wd:2 rd:4
>> disk 0, wo:0, o:1, dev:sda3
>> disk 2, wo:0, o:1, dev:sdc3
>>
>>
>>
>>
>> =========================================================================
>>
>>
>>
>> __ __ _ _ _ _ _ _
>> \ \/ /___ _ __ | || | / | _ _ _ __ ___| |_ __ _| |__ | | ___
>> \ // _ \ '_ \ | || |_ | |__| | | | '_ \/ __| __/ _` | '_ \| |/ _ \
>> / \ __/ | | | |__ _|| |__| |_| | | | \__ \ || (_| | |_) | | __/
>> /_/\_\___|_| |_| |_|(_)_| \__,_|_| |_|___/\__\__,_|_.__/|_|\___|
>>
>> (XEN) Xen version 4.1-unstable (jeremy@) (gcc version 4.4.3 20100127
>> (Red Hat 4.4.3-4) (GCC) ) Tue Apr 6 17:23:29 PDT 2010
>> (XEN) Latest ChangeSet: Tue Apr 06 17:23:12 2010 -0700
>> 21115:ea6c67dc4577
>> (XEN) Command line: com2=115200,8n1,0x3e8,5 console=com2,vga
>> cpufreq=xen iommu=verbose
>> (XEN) Video information:
>> (XEN) VGA is text mode 80x25, font 8x16
>> (XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
>> (XEN) EDID info not retrieved because no DDC retrieval method detected
>> (XEN) Disc information:
>> (XEN) Found 4 MBR signatures
>> (XEN) Found 4 EDD information structures
>> (XEN) Xen-e820 RAM map:
>> (XEN) 0000000000000000 - 000000000009d800 (usable)
>> (XEN) 000000000009d800 - 00000000000a0000 (reserved)
>> (XEN) 00000000000e0000 - 0000000000100000 (reserved)
>> (XEN) 0000000000100000 - 00000000bf790000 (usable)
>> (XEN) 00000000bf79e000 - 00000000bf7a0000 type 9
>> (XEN) 00000000bf7a0000 - 00000000bf7ae000 (ACPI data)
>> (XEN) 00000000bf7ae000 - 00000000bf7d0000 (ACPI NVS)
>> (XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved)
>> (XEN) 00000000bf7ed000 - 00000000c0000000 (reserved)
>> (XEN) 00000000e0000000 - 00000000f0000000 (reserved)
>> (XEN) 00000000fed20000 - 00000000fed40000 (reserved)
>> (XEN) 00000000fee00000 - 00000000fee01000 (reserved)
>> (XEN) 0000000100000000 - 0000000140000000 (usable)
>> (XEN) ACPI: RSDP 000FA110, 0024 (r2 ACPIAM)
>> (XEN) ACPI: XSDT BF7A0100, 0084 (r1 SMCI 20100225
>> MSFT 97)
>> (XEN) ACPI: FACP BF7A0290, 00F4 (r4 022510 FACP1918 20100225
>> MSFT 97)
>> (XEN) ACPI: DSDT BF7A05F0, 6C55 (r2 10605 10605000 0 INTL
>> 20051117)
>> (XEN) ACPI: FACS BF7AE000, 0040
>> (XEN) ACPI: APIC BF7A0390, 0092 (r2 022510 APIC1918 20100225
>> MSFT 97)
>> (XEN) ACPI: MCFG BF7A0430, 003C (r1 022510 OEMMCFG 20100225
>> MSFT 97)
>> (XEN) ACPI: OEMB BF7AE040, 0073 (r1 022510 OEMB1918 20100225
>> MSFT 97)
>> (XEN) ACPI: HPET BF7AA5F0, 0038 (r1 022510 OEMHPET 20100225
>> MSFT 97)
>> (XEN) ACPI: GSCI BF7AE0C0, 2024 (r1 022510 GMCHSCI 20100225
>> MSFT 97)
>> (XEN) ACPI: DMAR BF7B00F0, 0090 (r1 AMI OEMDMAR 1
>> MSFT 97)
>> (XEN) ACPI: SSDT BF7B1580, 0363 (r1 DpgPmm CpuPm 12 INTL
>> 20051117)
>> (XEN) ACPI: EINJ BF7AA630, 0130 (r1 AMIER AMI_EINJ 20100225
>> MSFT 97)
>> (XEN) ACPI: BERT BF7AA7C0, 0030 (r1 AMIER AMI_BERT 20100225
>> MSFT 97)
>> (XEN) ACPI: ERST BF7AA7F0, 01B0 (r1 AMIER AMI_ERST 20100225
>> MSFT 97)
>> (XEN) ACPI: HEST BF7AA9A0, 00A8 (r1 AMIER ABC_HEST 20100225
>> MSFT 97)
>> (XEN) System RAM: 4056MB (4153584kB)
>> (XEN) No NUMA configuration found
>> (XEN) Faking a node at 0000000000000000-0000000140000000
>> (XEN) Domain heap initialised
>> (XEN) found SMP MP-table at 000ff780
>> (XEN) DMI present.
>> (XEN) Using APIC driver default
>> (XEN) ACPI: PM-Timer IO Port: 0x808
>> (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0]
>> (XEN) ACPI: wakeup_vec[bf7ae00c], vec_size[20]
>> (XEN) ACPI: Local APIC address 0xfee00000
>> (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
>> (XEN) Processor #0 7:14 APIC version 21
>> (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
>> (XEN) Processor #2 7:14 APIC version 21
>> (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
>> (XEN) Processor #4 7:14 APIC version 21
>> (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
>> (XEN) Processor #6 7:14 APIC version 21
>> (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled)
>> (XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled)
>> (XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled)
>> (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled)
>> (XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
>> (XEN) ACPI: IOAPIC (id[0x07] address[0xfec00000] gsi_base[0])
>> (XEN) IOAPIC[0]: apic_id 7, version 32, address 0xfec00000, GSI 0-23
>> (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
>> (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
>> (XEN) ACPI: IRQ0 used by override.
>> (XEN) ACPI: IRQ2 used by override.
>> (XEN) ACPI: IRQ9 used by override.
>> (XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
>> (XEN) ACPI: HPET id: 0x8086a701 base: 0xfed00000
>> (XEN) [VT-D]dmar.c:679: Host address width 36
>> (XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD:
>> (XEN) [VT-D]dmar.c:398: dmaru->address = fed90000
>> (XEN) [VT-D]dmar.c:411: flags: INCLUDE_ALL
>> (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0
>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0
>> (XEN) [VT-D]dmar.c:571: RMRR region: base_addr ed000 end_address effff
>> (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0
>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0
>> (XEN) [VT-D]dmar.c:571: RMRR region: base_addr bf7ed000 end_address
>> bf7fffff
>> (XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
>> (XEN) PCI: MCFG area at e0000000 reserved in E820
>> (XEN) Using ACPI (MADT) for SMP configuration information
>> (XEN) Using scheduler: SMP Credit Scheduler (credit)
>> (XEN) Detected 2400.063 MHz processor.
>> (XEN) Initing memory sharing.
>> (XEN) EPT support 2M super page.
>> (XEN) VMX: Supported advanced features:
>> (XEN) - APIC MMIO access virtualisation
>> (XEN) - APIC TPR shadow
>> (XEN) - Extended Page Tables (EPT)
>> (XEN) - Virtual-Processor Identifiers (VPID)
>> (XEN) - Virtual NMI
>> (XEN) - MSR direct-access bitmap
>> (XEN) HVM: ASIDs enabled.
>> (XEN) HVM: VMX enabled
>> (XEN) HVM: Hardware Assisted Paging detected.
>> (XEN) Intel machine check reporting enabled
>> (XEN) [VT-D]iommu.c:1078: drhd->address = fed90000 iommu->reg =
>> ffff82c3fff57000
>> (XEN) [VT-D]iommu.c:1080: cap = c90780106f0462 ecap = f020e3
>> (XEN) Intel VT-d Snoop Control supported.
>> (XEN) Intel VT-d DMA Passthrough not supported.
>> (XEN) Intel VT-d Queued Invalidation supported.
>> (XEN) Intel VT-d Interrupt Remapping not supported.
>> (XEN) I/O virtualisation enabled
>> (XEN) I/O virtualisation for PV guests disabled
>> (XEN) EPT support 2M super page.
>> (XEN) EPT support 2M super page.
>> (XEN) EPT support 2M super page.
>> (XEN) Total of 4 processors activated.
>> (XEN) ENABLING IO-APIC IRQs
>> (XEN) -> Using new ACK method
>> (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
>> (XEN) TSC is reliable, synchronization unnecessary
>> (XEN) Platform timer is 14.318MHz HPET
>> �(XEN) Allocated console ring of 32 KiB.
>> (XEN) microcode.c:73:d32767 microcode: CPU1 resumed
>> (XEN) microcode.c:73:d32767 microcode: CPU2 resumed
>> (XEN) Brought up 4 CPUs
>> (XEN) microcode.c:73:d32767 microcode: CPU3 resumed
>> (XEN) Turbo Mode detected!
>> (XEN) HPET: 8 timers in total, 8 timers will be used for broadcast
>> (XEN) ACPI sleep modes: S3
>> (XEN) mcheck_poll: Machine check polling timer started.
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:0.0
>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:8.0
>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:8.1
>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:8.2
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:8.3
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:10.0
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:10.1
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.0
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.0
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.0
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3
>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 3:0.0
>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 4:0.0
>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 5:0.0
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.0
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.1
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.2
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.3
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.4
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.5
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.6
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 6:3.7
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.0
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.1
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.0
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.1
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.0
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.1
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.2
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.4
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.0
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.1
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.2
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.3
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.0
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.1
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.2
>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.3
>> (XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg =
>> ffff82c3fff57000
>> (XEN) *** LOADING DOMAIN 0 ***
>> (XEN) elf_parse_binary: phdr: paddr=0x1000000 memsz=0x69c000
>> (XEN) elf_parse_binary: phdr: paddr=0x169c000 memsz=0xe3cb0
>> (XEN) elf_parse_binary: phdr: paddr=0x1780000 memsz=0x888
>> (XEN) elf_parse_binary: phdr: paddr=0x1781000 memsz=0x14498
>> (XEN) elf_parse_binary: phdr: paddr=0x1796000 memsz=0x9f5000
>> (XEN) elf_parse_binary: memory: 0x1000000 -> 0x218b000
>> (XEN) elf_xen_parse_note: GUEST_OS = "linux"
>> (XEN) elf_xen_parse_note: GUEST_VERSION = "2.6"
>> (XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0"
>> (XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000
>> (XEN) elf_xen_parse_note: ENTRY = 0xffffffff81796200
>> (XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff81009000
>> (XEN) elf_xen_parse_note: FEATURES =
>> "!writable_page_tables|pae_pgdir_above_4gb"
>> (XEN) elf_xen_parse_note: PAE_MODE = "yes"
>> (XEN) elf_xen_parse_note: LOADER = "generic"
>> (XEN) elf_xen_parse_note: unknown xen elf note (0xd)
>> (XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1
>> (XEN) elf_xen_parse_note: HV_START_LOW = 0xffff800000000000
>> (XEN) elf_xen_parse_note: PADDR_OFFSET = 0x0
>> (XEN) elf_xen_addr_calc_check: addresses:
>> (XEN) virt_base = 0xffffffff80000000
>> (XEN) elf_paddr_offset = 0x0
>> (XEN) virt_offset = 0xffffffff80000000
>> (XEN) virt_kstart = 0xffffffff81000000
>> (XEN) virt_kend = 0xffffffff8218b000
>> (XEN) virt_entry = 0xffffffff81796200
>> (XEN) p2m_base = 0xffffffffffffffff
>> (XEN) Xen kernel: 64-bit, lsb, compat32
>> (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x218b000
>> (XEN) PHYSICAL MEMORY ARRANGEMENT:
>> (XEN) Dom0 alloc.: 0000000138000000->000000013c000000 (981633
>> pages to be allocated)
>> (XEN) VIRTUAL MEMORY ARRANGEMENT:
>> (XEN) Loaded kernel: ffffffff81000000->ffffffff8218b000
>> (XEN) Init. ramdisk: ffffffff8218b000->ffffffff82b69800
>> (XEN) Phys-Mach map: ffffffff82b6a000->ffffffff83307408
>> (XEN) Start info: ffffffff83308000->ffffffff833084b4
>> (XEN) Page tables: ffffffff83309000->ffffffff83326000
>> (XEN) Boot stack: ffffffff83326000->ffffffff83327000
>> (XEN) TOTAL: ffffffff80000000->ffffffff83400000
>> (XEN) ENTRY ADDRESS: ffffffff81796200
>> (XEN) Dom0 has maximum 4 VCPUs
>> (XEN) elf_load_binary: phdr 0 at 0xffffffff81000000 ->
>> 0xffffffff8169c000
>> (XEN) elf_load_binary: phdr 1 at 0xffffffff8169c000 ->
>> 0xffffffff8177fcb0
>> (XEN) elf_load_binary: phdr 2 at 0xffffffff81780000 ->
>> 0xffffffff81780888
>> (XEN) elf_load_binary: phdr 3 at 0xffffffff81781000 ->
>> 0xffffffff81795498
>> (XEN) elf_load_binary: phdr 4 at 0xffffffff81796000 ->
>> 0xffffffff81830000
>> (XEN) Scrubbing Free RAM: .done.
>> (XEN) Xen trace buffers: disabled
>> (XEN) Std. Loglevel: All
>> (XEN) Guest Loglevel: All
>> (XEN) Xen is relinquishing VGA console.
>> (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch
>> input to Xen)
>> (XEN) Freed 164kB init memory.
>> mapping kernel into physical memory
>> Xen: setup ISA identity maps
>> about to get started...
>> Initializing cgroup subsys cpuset
>> Initializing cgroup subsys cpu
>> Linux version 2.6.32.11 (jeremy@lilith.goop.org) (gcc version 4.4.3
>> 20100127 (Red Hat 4.4.3-4) (GCC) ) #7 SMP PREEMPT Mon Apr 5 14:58:54
>> PDT 2010
>> Command line: ro root=/dev/mapper/vg_lilith--raid-root
>> LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc
>> KEYTABLE=us ignore_loglevel earlyprintk=xen console=hvc0 rdshell
>> pcie_aspm=off
>> KERNEL supported cpus:
>> Intel GenuineIntel
>> AMD AuthenticAMD
>> Centaur CentaurHauls
>> xen_release_chunk: looking at area pfn bf790-bf79e: 14 pages freed
>> xen_release_chunk: looking at area pfn bf7e0-bf7ed: 13 pages freed
>> xen_release_chunk: looking at area pfn c0000-e0000: 131072 pages freed
>> xen_release_chunk: looking at area pfn f0000-fec00: 14977 pages freed
>> xen_release_chunk: looking at area pfn fec01-fed20: 0 pages freed
>> xen_release_chunk: looking at area pfn fed40-fee00: 0 pages freed
>> released 146076 pages of unused memory
>> BIOS-provided physical RAM map:
>> Xen: 0000000000000000 - 000000000009d800 (usable)
>> Xen: 000000000009d800 - 0000000000100000 (reserved)
>> Xen: 0000000000100000 - 00000000bf790000 (usable)
>> Xen: 00000000bf79e000 - 00000000bf7a0000 type 9
>> Xen: 00000000bf7a0000 - 00000000bf7ae000 (ACPI data)
>> Xen: 00000000bf7ae000 - 00000000bf7d0000 (ACPI NVS)
>> Xen: 00000000bf7d0000 - 00000000bf7e0000 (reserved)
>> Xen: 00000000bf7ed000 - 00000000c0000000 (reserved)
>> Xen: 00000000e0000000 - 00000000f0000000 (reserved)
>> Xen: 00000000fec00000 - 00000000fec01000 (reserved)
>> Xen: 00000000fed20000 - 00000000fed40000 (reserved)
>> Xen: 00000000fee00000 - 00000000fee01000 (reserved)
>> debug: ignoring loglevel setting.
>> bootconsole [xenboot0] enabled
>> DMI present.
>> last_pfn = 0xbf790 max_arch_pfn = 0x400000000
>> x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
>> initial memory mapped : 0 - 20000000
>> init_memory_mapping: 0000000000000000-00000000bf790000
>> 0000000000 - 00bf790000 page 4k
>> kernel direct mapping tables up to bf790000 @ 100000-700000
>> RAMDISK: 0218b000 - 02b69800
>> ACPI: RSDP 00000000000fa110 00024 (v02 ACPIAM)
>> ACPI: XSDT 00000000bf7a0100 00084 (v01 SMCI 20100225 MSFT
>> 00000097)
>> ACPI: FACP 00000000bf7a0290 000F4 (v04 022510 FACP1918 20100225 MSFT
>> 00000097)
>> ACPI: DSDT 00000000bf7a05f0 06C55 (v02 10605 10605000 00000000 INTL
>> 20051117)
>> ACPI: FACS 00000000bf7ae000 00040
>> ACPI: APIC 00000000bf7a0390 00092 (v02 022510 APIC1918 20100225 MSFT
>> 00000097)
>> ACPI: MCFG 00000000bf7a0430 0003C (v01 022510 OEMMCFG 20100225 MSFT
>> 00000097)
>> ACPI: OEMB 00000000bf7ae040 00073 (v01 022510 OEMB1918 20100225 MSFT
>> 00000097)
>> ACPI: HPET 00000000bf7aa5f0 00038 (v01 022510 OEMHPET 20100225 MSFT
>> 00000097)
>> ACPI: GSCI 00000000bf7ae0c0 02024 (v01 022510 GMCHSCI 20100225 MSFT
>> 00000097)
>> ACPI: 00000000bf7b00f0 00090 (v01 AMI OEMDMAR 00000001 MSFT
>> 00000097)
>> ACPI: SSDT 00000000bf7b1580 00363 (v01 DpgPmm CpuPm 00000012 INTL
>> 20051117)
>> ACPI: EINJ 00000000bf7aa630 00130 (v01 AMIER AMI_EINJ 20100225 MSFT
>> 00000097)
>> ACPI: BERT 00000000bf7aa7c0 00030 (v01 AMIER AMI_BERT 20100225 MSFT
>> 00000097)
>> ACPI: ERST 00000000bf7aa7f0 001B0 (v01 AMIER AMI_ERST 20100225 MSFT
>> 00000097)
>> ACPI: HEST 00000000bf7aa9a0 000A8 (v01 AMIER ABC_HEST 20100225 MSFT
>> 00000097)
>> ACPI: Local APIC address 0xfee00000
>> No NUMA configuration found
>> Faking a node at 0000000000000000-00000000bf790000
>> Bootmem setup node 0 0000000000000000-00000000bf790000
>> NODE_DATA [0000000000001000 - 0000000000005fff]
>> bootmap [0000000000008000 - 000000000001fef7] pages 18
>> (8 early reservations) ==> bootmem [0000000000 - 00bf790000]
>> #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 -
>> 0000001000]
>> #1 [0003309000 - 0003326000] XEN PAGETABLES ==> [0003309000 -
>> 0003326000]
>> #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 -
>> 0000008000]
>> #3 [0001000000 - 000216a048] TEXT DATA BSS ==> [0001000000 -
>> 000216a048]
>> #4 [000218b000 - 0002b69800] RAMDISK ==> [000218b000 -
>> 0002b69800]
>> #5 [0002b6a000 - 0003309000] XEN START INFO ==> [0002b6a000 -
>> 0003309000]
>> #6 [000216b000 - 000216b21b] BRK ==> [000216b000 -
>> 000216b21b]
>> #7 [0000100000 - 00006e0000] PGTABLE ==> [0000100000 -
>> 00006e0000]
>> found SMP MP-table at [ffff8800000ff780] ff780
>> Zone PFN ranges:
>> DMA 0x00000000 -> 0x00001000
>> DMA32 0x00001000 -> 0x00100000
>> Normal 0x00100000 -> 0x00100000
>> Movable zone start PFN for each node
>> early_node_map[2] active PFN ranges
>> 0: 0x00000000 -> 0x0000009d
>> 0: 0x00000100 -> 0x000bf790
>> On node 0 totalpages: 784173
>> DMA zone: 88 pages used for memmap
>> DMA zone: 1507 pages reserved
>> DMA zone: 2402 pages, LIFO batch:0
>> DMA32 zone: 16762 pages used for memmap
>> DMA32 zone: 763414 pages, LIFO batch:31
>> ACPI: PM-Timer IO Port: 0x808
>> ACPI: Local APIC address 0xfee00000
>> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
>> ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
>> ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
>> ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
>> ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled)
>> ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled)
>> ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled)
>> ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled)
>> ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
>> ACPI: IOAPIC (id[0x07] address[0xfec00000] gsi_base[0])
>> IOAPIC[0]: apic_id 7, version 0, address 0xfec00000, GSI 0-0
>> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
>> ERROR: Unable to locate IOAPIC for GSI 2
>> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
>> ERROR: Unable to locate IOAPIC for GSI 9
>> Using ACPI (MADT) for SMP configuration information
>> ACPI: HPET id: 0x8086a701 base: 0xfed00000
>> SMP: Allowing 4 CPUs, 0 hotplug CPUs
>> nr_irqs_gsi: 256
>> PM: Registered nosave memory: 000000000009d000 - 000000000009e000
>> PM: Registered nosave memory: 000000000009e000 - 0000000000100000
>> Allocating PCI resources starting at c0000000 (gap: c0000000:20000000)
>> Booting paravirtualized kernel on Xen
>> Xen version: 4.1-unstable (preserve-AD) (dom0)
>> NR_CPUS:16 nr_cpumask_bits:16 nr_cpu_ids:4 nr_node_ids:1
>> PERCPU: Embedded 28 pages/cpu @ffff88000336d000 s83096 r8192 d23400
>> u114688
>> pcpu-alloc: s83096 r8192 d23400 u114688 alloc=28*4096
>> pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
>> trying to map vcpu_info 0 at ffff880003378020, mfn 13b378, offset 32
>> cpu 0 using vcpu_info at ffff880003378020
>> trying to map vcpu_info 1 at ffff880003394020, mfn 13b394, offset 32
>> cpu 1 using vcpu_info at ffff880003394020
>> trying to map vcpu_info 2 at ffff8800033b0020, mfn 13b3b0, offset 32
>> cpu 2 using vcpu_info at ffff8800033b0020
>> trying to map vcpu_info 3 at ffff8800033cc020, mfn 13b3cc, offset 32
>> cpu 3 using vcpu_info at ffff8800033cc020
>> Xen: using vcpu_info placement
>> Built 1 zonelists in Node order, mobility grouping on. Total pages:
>> 765816
>> Policy zone: DMA32
>> Kernel command line: ro root=/dev/mapper/vg_lilith--raid-root
>> LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc
>> KEYTABLE=us ignore_loglevel earlyprintk=xen console=hvc0 rdshell
>> pcie_aspm=off
>> PCIe ASPM is disabled
>> PID hash table entries: 4096 (order: 3, 32768 bytes)
>> Initializing CPU#0
>> DMA: Placing 64MB software IO TLB between ffff88000794a000 -
>> ffff88000b94a000
>> DMA: software IO TLB at phys 0x794a000 - 0xb94a000
>> xen_swiotlb_fixup: buf=ffff88000794a000 size=67108864
>> xen_swiotlb_fixup: buf=ffff88000b9aa000 size=32768
>> Memory: 2960308k/3137088k available (4691k kernel code, 396k absent,
>> 176384k reserved, 2987k data, 656k init)
>> Hierarchical RCU implementation.
>> NR_IRQS:4352 nr_irqs:1280
>> xen: --> irq=0
>> xen: --> irq=1
>> xen: --> irq=2
>> xen: --> irq=3
>> xen: --> irq=4
>> xen: --> irq=5
>> xen: --> irq=6
>> xen: --> irq=7
>> xen: --> irq=8
>> xen: --> irq=9
>> xen: --> irq=10
>> xen: --> irq=11
>> xen: --> irq=12
>> xen: --> irq=13
>> xen: --> irq=14
>> xen: --> irq=15
>> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
>> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
>> xen: sci override: source_irq=9 global_irq=9 trigger=c polarity=1
>> xen: registering gsi 9 triggering 0 polarity 0
>> xen_allocate_pirq: returning irq 9 for gsi 9
>> xen: --> irq=9
>> xen: acpi sci 9
>> Console: colour VGA+ 80x25
>> console [hvc0] enabled, bootconsole disabled
>> console [hvc0] enabled, bootconsole disabled
>> Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
>> ... MAX_LOCKDEP_SUBCLASSES: 8
>> ... MAX_LOCK_DEPTH: 48
>> ... MAX_LOCKDEP_KEYS: 8191
>> ... CLASSHASH_SIZE: 4096
>> ... MAX_LOCKDEP_ENTRIES: 16384
>> ... MAX_LOCKDEP_CHAINS: 32768
>> ... CHAINHASH_SIZE: 16384
>> memory used by lock dependency info: 5855 kB
>> per task-struct memory footprint: 1920 bytes
>> Xen: using vcpuop timer interface
>> installing Xen timer for CPU 0
>> alloc irq_desc for 1279 on node 0
>> alloc kstat_irqs on node 0
>> Detected 2400.062 MHz processor.
>> Calibrating delay loop (skipped), value calculated using timer
>> frequency.. 4800.12 BogoMIPS (lpj=2400062)
>> Security Framework initialized
>> SELinux: Initializing.
>> SELinux: Starting in permissive mode
>> Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
>> Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
>> Mount-cache hash table entries: 256
>> Initializing cgroup subsys ns
>> Initializing cgroup subsys cpuacct
>> CPU: L1 I cache: 32K, L1 D cache: 32K
>> CPU: L2 cache: 256K
>> CPU: L3 cache: 8192K
>> CPU 0/0x0 -> Node 0
>> CPU: Unsupported number of siblings 16
>> Performance Events: unsupported p6 CPU model 30 no PMU driver,
>> software events only.
>> lockdep: fixing up alternatives.
>> SMP alternatives: switching to UP code
>> ACPI: Core revision 20090903
>> alloc irq_desc for 1278 on node 0
>> alloc kstat_irqs on node 0
>> cpu 0 spinlock event irq 1278
>> alloc irq_desc for 1277 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1276 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1275 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1274 on node 0
>> alloc kstat_irqs on node 0
>> installing Xen timer for CPU 1
>> alloc irq_desc for 1273 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1272 on node 0
>> alloc kstat_irqs on node 0
>> cpu 1 spinlock event irq 1272
>> lockdep: fixing up alternatives.
>> SMP alternatives: switching to SMP code
>> alloc irq_desc for 1271 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1270 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1269 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1268 on node 0
>> alloc kstat_irqs on node 0
>> Initializing CPU#1
>> CPU: L1 I cache: 32K, L1 D cache: 32K
>> CPU: L2 cache: 256K
>> CPU: L3 cache: 8192K
>> CPU 1/0x0 -> Node 0
>> CPU: Unsupported number of siblings 16
>> installing Xen timer for CPU 2
>> alloc irq_desc for 1267 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1266 on node 0
>> alloc kstat_irqs on node 0
>> cpu 2 spinlock event irq 1266
>> alloc irq_desc for 1265 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1264 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1263 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1262 on node 0
>> alloc kstat_irqs on node 0
>> Initializing CPU#2
>> CPU: L1 I cache: 32K, L1 D cache: 32K
>> CPU: L2 cache: 256K
>> CPU: L3 cache: 8192K
>> CPU 2/0x0 -> Node 0
>> CPU: Unsupported number of siblings 16
>> installing Xen timer for CPU 3
>> alloc irq_desc for 1261 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1260 on node 0
>> alloc kstat_irqs on node 0
>> cpu 3 spinlock event irq 1260
>> alloc irq_desc for 1259 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1258 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1257 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1256 on node 0
>> alloc kstat_irqs on node 0
>> Initializing CPU#3
>> CPU: L1 I cache: 32K, L1 D cache: 32K
>> CPU: L2 cache: 256K
>> CPU: L3 cache: 8192K
>> CPU 3/0x0 -> Node 0
>> CPU: Unsupported number of siblings 16
>> Brought up 4 CPUs
>> Grant table initialized
>> Time: 16:45:17 Date: 04/07/10
>> NET: Registered protocol family 16
>> alloc irq_desc for 1255 on node 0
>> alloc kstat_irqs on node 0
>> ACPI: bus type pci registered
>> PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
>> PCI: MCFG area at e0000000 reserved in E820
>> PCI: Using MMCONFIG at e0000000 - efffffff
>> PCI: Using configuration type 1 for base access
>> bio: create slab<bio-0> at 0
>> ERROR: Unable to locate IOAPIC for GSI 9
>> ACPI: EC: Look up EC in DSDT
>> ACPI Warning for \_SB_._OSC: Return type mismatch - found Integer,
>> expected Buffer (20090903/nspredef-1006)
>> \_SB_:_OSC evaluation returned wrong type
>> _OSC request data:1 6
>> ACPI: Executed 1 blocks of module-level executable AML code
>> ACPI: Interpreter enabled
>> ACPI: (supports S0 S1 S4 S5)
>> ACPI: Using IOAPIC for interrupt routing
>> ACPI Warning: Incorrect checksum in table [OEMB] - 91, should be 8E
>> (20090903/tbutils-314)
>> ACPI Warning: Incorrect checksum in table [ ] - 7B, should be BF
>> (20090903/tbutils-314)
>> ACPI: No dock devices found.
>> ACPI: PCI Root Bridge [PCI0] (0000:00)
>> pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
>> pci 0000:00:03.0: PME# disabled
>> pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
>> pci 0000:00:05.0: PME# disabled
>> pci 0000:00:1a.0: reg 10 32bit mmio: [0xfb3fc000-0xfb3fc3ff]
>> pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
>> pci 0000:00:1a.0: PME# disabled
>> pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
>> pci 0000:00:1c.0: PME# disabled
>> pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
>> pci 0000:00:1c.4: PME# disabled
>> pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
>> pci 0000:00:1c.5: PME# disabled
>> pci 0000:00:1d.0: reg 10 32bit mmio: [0xfb3fa000-0xfb3fa3ff]
>> pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
>> pci 0000:00:1d.0: PME# disabled
>> pci 0000:00:1f.2: reg 10 io port: [0xb400-0xb407]
>> pci 0000:00:1f.2: reg 14 io port: [0xbc00-0xbc03]
>> pci 0000:00:1f.2: reg 18 io port: [0xb880-0xb887]
>> pci 0000:00:1f.2: reg 1c io port: [0xb800-0xb803]
>> pci 0000:00:1f.2: reg 20 io port: [0xb480-0xb49f]
>> pci 0000:00:1f.2: reg 24 32bit mmio: [0xfb3f8000-0xfb3f87ff]
>> pci 0000:00:1f.2: PME# supported from D3hot
>> pci 0000:00:1f.2: PME# disabled
>> pci 0000:00:1f.3: reg 10 64bit mmio: [0xfb3f6000-0xfb3f60ff]
>> pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
>> pci 0000:03:00.0: reg 10 32bit mmio: [0xfb420000-0xfb43ffff]
>> pci 0000:03:00.0: reg 14 32bit mmio: [0xfb480000-0xfb4fffff]
>> pci 0000:03:00.0: reg 18 io port: [0xcc00-0xcc1f]
>> pci 0000:03:00.0: reg 1c 32bit mmio: [0xfb41c000-0xfb41ffff]
>> pci 0000:03:00.0: reg 30 32bit mmio pref: [0xfb440000-0xfb47ffff]
>> pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
>> pci 0000:03:00.0: PME# disabled
>> pci 0000:00:1c.0: bridge io port: [0xc000-0xcfff]
>> pci 0000:00:1c.0: bridge 32bit mmio: [0xfb400000-0xfb4fffff]
>> pci 0000:04:00.0: reg 10 32bit mmio: [0xfb5e0000-0xfb5fffff]
>> pci 0000:04:00.0: reg 18 io port: [0xdc00-0xdc1f]
>> pci 0000:04:00.0: reg 1c 32bit mmio: [0xfb5dc000-0xfb5dffff]
>> pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
>> pci 0000:04:00.0: PME# disabled
>> pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff]
>> pci 0000:00:1c.4: bridge 32bit mmio: [0xfb500000-0xfb5fffff]
>> pci 0000:05:00.0: reg 10 32bit mmio: [0xfb6e0000-0xfb6fffff]
>> pci 0000:05:00.0: reg 18 io port: [0xec00-0xec1f]
>> pci 0000:05:00.0: reg 1c 32bit mmio: [0xfb6dc000-0xfb6dffff]
>> pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
>> pci 0000:05:00.0: PME# disabled
>> pci 0000:00:1c.5: bridge io port: [0xe000-0xefff]
>> pci 0000:00:1c.5: bridge 32bit mmio: [0xfb600000-0xfb6fffff]
>> pci 0000:06:03.0: reg 10 32bit mmio pref: [0xfa000000-0xfaffffff]
>> pci 0000:06:03.0: reg 14 32bit mmio: [0xfb7fc000-0xfb7fffff]
>> pci 0000:06:03.0: reg 18 32bit mmio: [0xfb800000-0xfbffffff]
>> pci 0000:00:1e.0: transparent bridge
>> pci 0000:00:1e.0: bridge 32bit mmio: [0xfb700000-0xfbffffff]
>> pci 0000:00:1e.0: bridge 64bit mmio pref: [0xfa000000-0xfaffffff]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR1E._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0ehci_hcd 0000:00:1a.0:
>> port 1 high speed
>> ehci_hcd 0000:00:1a.0: GetStatus port 1 status 001005 POWER sig=se0
>> PE CONNECT
>> ahci 0000:00:1f.2: version 3.0
>> xen: registering gsi 19 triggering 0 polarity 1
>> alloc irq_desc for 19 on node 0
>> alloc kstat_irqs on node 0
>> xen: --> irq=19
>> ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
>> alloc irq_desc for 1247 on node 0
>> alloc kstat_irqs on node 0
>> ahci: SSS flag set, parallel bus scan disabled
>> ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x3f impl
>> SATA mode
>> ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum
>> part ems sxs apst
>> ahci 0000:00:1f.2: setting latency timer to 64
>> scsi0 : ahci
>> scsi1 : ahci
>> scsi2 : ahci
>> scsi3 : ahci
>> scsi4 : ahci
>> scsi5 : ahci
>> ata1: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8100 irq 1247
>> ata2: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8180 irq 1247
>> ata3: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8200 irq 1247
>> ata4: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8280 irq 1247
>> ata5: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8300 irq 1247
>> ata6: SATA max UDMA/133 abar m2048@0xfb3f8000 port 0xfb3f8380 irq 1247
>> usb 1-1: udev 2, busnum 1, minor = 1
>> usb 1-1: New USB device found, idVendor=8087, idProduct=0020
>> usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
>> usb 1-1: usb_probe_device
>> usb 1-1: configuration #1 chosen from 1 choice
>> usb 1-1: adding 1-1:1.0 (config #1, interface 0)
>> hub 1-1:1.0: usb_probe_interface
>> hub 1-1:1.0: usb_probe_interface - got id
>> hub 1-1:1.0: USB hub found
>> hub 1-1:1.0: 6 ports detected
>> hub 1-1:1.0: standalone hub
>> hub 1-1:1.0: individual port power switching
>> hub 1-1:1.0: individual port over-current protection
>> hub 1-1:1.0: Single TT
>> hub 1-1:1.0: TT requires at most 8 FS bit times (666 ns)
>> hub 1-1:1.0: Port indicators are supported
>> hub 1-1:1.0: power on to power good time: 100ms
>> hub 1-1:1.0: local power source is good
>> hub 1-1:1.0: enabling power on all ports
>> hub 2-0:1.0: state 7 ports 2 chg 0002 evt 0000
>> hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
>> ehci_hcd 0000:00:1d.0: port 1 high speed
>> ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 POWER sig=se0
>> PE CONNECT
>> hub 1-1:1.0: port 2: status 0101 change 0001
>> usb 2-1: new high speed USB device using ehci_hcd and address 2
>> ehci_hcd 0000:00:1d.0: port 1 high speed
>> ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 POWER sig=se0
>> PE CONNECT
>> usb 1-1: link qh256-0001/ffff8800bc51f9c0 start 1 [1/0 us]
>> usb 2-1: udev 2, busnum 2, minor = 129
>> usb 2-1: New USB device found, idVendor=8087, idProduct=0020
>> usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
>> usb 2-1: usb_probe_device
>> usb 2-1: configuration #1 chosen from 1 choice
>> usb 2-1: adding 2-1:1.0 (config #1, interface 0)
>> hub 2-1:1.0: usb_probe_interface
>> hub 2-1:1.0: usb_probe_interface - got id
>> hub 2-1:1.0: USB hub found
>> hub 2-1:1.0: 8 ports detected
>> hub 2-1:1.0: standalone hub
>> hub 2-1:1.0: individual port power switching
>> hub 2-1:1.0: individual port over-current protection
>> hub 2-1:1.0: Single TT
>> hub 2-1:1.0: TT requires at most 8 FS bit times (666 ns)
>> hub 2-1:1.0: Port indicators are supported
>> hub 2-1:1.0: power on to power good time: 100ms
>> hub 2-1:1.0: local power source is good
>> hub 2-1:1.0: enabling power on all ports
>> hub 1-1:1.0: state 7 ports 6 chg 0004 evt 0000
>> hub 1-1:1.0: port 2, status 0101, change 0000, 12 Mb/s
>> hub 1-1:1.0: port 2 not reset yet, waiting 10ms
>> usb 1-1.2: new full speed USB device using ehci_hcd and address 3
>> ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> hub 1-1:1.0: port 2 not reset yet, waiting 10ms
>> ata1.00: ATA-8: WDC WD10EADS-00P8B0, 01.00A01, max UDMA/133
>> ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
>> ata1.00: configured for UDMA/133
>> scsi 0:0:0:0: Direct-Access ATA WDC WD10EADS-00P 01.0 PQ: 0
>> ANSI: 5
>> sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
>> sd 0:0:0:0: [sda] Write Protect is off
>> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
>> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
>> support DPO or FUA
>> sd 0:0:0:0: Attached scsi generic sg0 type 0
>> sda:
>> usb 2-1: link qh256-0001/ffff8800bc51f6c0 start 1 [1/0 us]
>> sda1 sda2 sda3 sda4
>> sd 0:0:0:0: [sda] Attached SCSI disk
>> usb 1-1.2: skipped 1 descriptor after interface
>> usb 1-1.2: skipped 1 descriptor after interface
>> usb 1-1.2: default language 0x0409
>> usb 1-1.2: udev 3, busnum 1, minor = 2
>> usb 1-1.2: New USB device found, idVendor=0557, idProduct=2221
>> usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
>> usb 1-1.2: Product: Hermon USB hidmouse Device
>> usb 1-1.2: Manufacturer: Winbond Electronics Corp
>> usb 1-1.2: usb_probe_device
>> usb 1-1.2: configuration #1 chosen from 1 choice
>> usb 1-1.2: adding 1-1.2:1.0 (config #1, interface 0)
>> usbhid 1-1.2:1.0: usb_probe_interface
>> usbhid 1-1.2:1.0: usb_probe_interface - got id
>> input: Winbond Electronics Corp Hermon USB hidmouse Device as
>> /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input4
>> generic-usb 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse
>> [Winbond Electronics Corp Hermon USB hidmouse Device] on
>> usb-0000:00:1a.0-1.2/input0
>> usb 1-1.2: adding 1-1.2:1.1 (config #1, interface 1)
>> usbhid 1-1.2:1.1: usb_probe_interface
>> usbhid 1-1.2:1.1: usb_probe_interface - got id
>> input: Winbond Electronics Corp Hermon USB hidmouse Device as
>> /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.1/input/input5
>> usb 1-1.2: link qh8-0601/ffff8800be6225c0 start 2 [1/2 us]
>> generic-usb 0003:0557:2221.0002: input,hidraw1: USB HID v1.00
>> Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on
>> usb-0000:00:1a.0-1.2/input1
>> hub 2-1:1.0: state 7 ports 8 chg 0000 evt 0000
>> hub 1-1:1.0: state 7 ports 6 chg 0000 evt 0004
>> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata2.00: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
>> ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
>> ata2.00: configured for UDMA/133
>> scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0
>> ANSI: 5
>> sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
>> sd 1:0:0:0: Attached scsi generic sg1 type 0
>> sd 1:0:0:0: [sdb] Write Protect is off
>> sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
>> sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't
>> support DPO or FUA
>> sdb: sdb1 sdb2 sdb3 sdb4
>> sd 1:0:0:0: [sdb] Attached SCSI disk
>> input: ImExPS/2 Generic Explorer Mouse as
>> /devices/platform/i8042/serio1/input/input6
>> ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata3.00: ATA-8: WDC WD10EADS-00P8B0, 01.00A01, max UDMA/133
>> ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
>> ata3.00: configured for UDMA/133
>> scsi 2:0:0:0: Direct-Access ATA WDC WD10EADS-00P 01.0 PQ: 0
>> ANSI: 5
>> sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
>> sd 2:0:0:0: Attached scsi generic sg2 type 0
>> sd 2:0:0:0: [sdc] Write Protect is off
>> sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
>> sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't
>> support DPO or FUA
>> sdc: sdc1 sdc2 sdc3 sdc4
>> sd 2:0:0:0: [sdc] Attached SCSI disk
>> hub 2-1:1.0: hub_suspend
>> usb 2-1: unlink qh256-0001/ffff8800bc51f6c0 start 1 [1/0 us]
>> usb 2-1: usb auto-suspend
>> ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata4.00: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
>> ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
>> ata4.00: configured for UDMA/133
>> scsi 3:0:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0
>> ANSI: 5
>> sd 3:0:0:0: [sdd] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
>> sd 3:0:0:0: Attached scsi generic sg3 type 0
>> sd 3:0:0:0: [sdd] Write Protect is off
>> sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
>> sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't
>> support DPO or FUA
>> sdd: sdd1 sdd2 sdd3 sdd4
>> sd 3:0:0:0: [sdd] Attached SCSI disk
>> ata5: SATA link down (SStatus 0 SControl 300)
>> ata6: SATA link down (SStatus 0 SControl 300)
>> md: raid10 personality registered for level 10
>> Intel AES-NI instructions are not detected.
>> md: md0 stopped.
>> md: bind<sdb3>
>> md: bind<sdc3>
>> md: bind<sdd3>
>> md: bind<sda3>
>> md: kicking non-fresh sdd3 from array!
>> md: unbind<sdd3>
>> md: export_rdev(sdd3)
>> md: kicking non-fresh sdb3 from array!
>> md: unbind<sdb3>
>> md: export_rdev(sdb3)
>> raid10: raid set md0 active with 2 out of 4 devices
>> md0: detected capacity change from 0 to 838860668928
>> md0: unknown partition table
>> hub 2-0:1.0: hub_suspend
>> usb usb2: bus auto-suspend
>> ehci_hcd 0000:00:1d.0: suspend root hub
>>
>> Password:***********
>> EXT4-fs (dm-2): mounted filesystem with ordered data mode
>> type=1404 audit(1270658817.238:2): enforcing=1 old_enforcing=0
>> auid=4294967295 ses=4294967295
>> SELinux: 8192 avtab hash slots, 162639 rules.
>> SELinux: 8192 avtab hash slots, 162639 rules.
>> SELinux: 8 users, 12 roles, 3092 types, 152 bools, 1 sens, 1024 cats
>> SELinux: 77 classes, 162639 rules
>> SELinux: Completing initialization.
>> SELinux: Setting up existing superblocks.
>> SELinux: initialized (dev dm-2, type ext4), uses xattr
>> SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
>> SELinux: initialized (dev selinuxfs, type selinuxfs), uses
>> genfs_contexts
>> SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
>> SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition
>> SIDs
>> SELinux: initialized (dev devpts, type devpts), uses transition SIDs
>> SELinux: initialized (dev inotifyfs, type inotifyfs), uses
>> genfs_contexts
>> SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses
>> genfs_contexts
>> SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
>> SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
>> SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
>> SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
>> SELinux: initialized (dev proc, type proc), uses genfs_contexts
>> SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
>> SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
>> SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
>> type=1403 audit(1270658817.689:3): policy loaded auid=4294967295
>> ses=4294967295
>> Welcome to Fedora
>> Press 'I' to enter interactive startup.
>> Starting udev: udev: starting version 145
>> ACPI: SSDT 00000000bf7b0180 00F20 (v01 DpgPmm P001Ist 00000011 INTL
>> 20051117)
>> ACPI: SSDT 00000000bf7b10a0 004D5 (v01 PmRef P001Cst 00003001 INTL
>> 20051117)
>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
>> (XEN) Monitor-Mwait will be used to enter C-1 state
>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
>> (XEN) Monitor-Mwait will be used to enter C-2 state
>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
>> (XEN) Monitor-Mwait will be used to enter C-3 state
>> ACPI: CPU-1 (power states: C1[C1] C2[C2] C3[C3])
>> e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
>> e1000e: Copyright (c) 1999-2008 Intel Corporation.
>> xen: registering gsi 16 triggering 0 polarity 1
>> xen_allocate_pirq: returning irq 16 for gsi 16
>> xen: --> irq=16
>> Already setup the GSI :16
>> e1000e 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
>> e1000e 0000:03:00.0: setting latency timer to 64
>> alloc irq_desc for 1246 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1245 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1244 on node 0
>> alloc kstat_irqs on node 0
>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
>> (XEN) Monitor-Mwait will be used to enter C-1 state
>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
>> (XEN) Monitor-Mwait will be used to enter C-2 state
>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
>> (XEN) Monitor-Mwait will be used to enter C-3 state
>> ACPI: CPU-1 (power states: C1[C1] C2[C2] C3[C3])
>> 0000:03:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1b:21:4f:65:6b
>> 0000:03:00.0: eth0: Intel(R) PRO/1000 Network Connection
>> 0000:03:00.0: eth0: MAC: 3, PHY: 8, PBA No: e46981-003
>> xen: registering gsi 16 triggering 0 polarity 1
>> xen_allocate_pirq: returning irq 16 for gsi 16
>> xen: --> irq=16
>> Already setup the GSI :16
>> e1000e 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
>> e1000e 0000:04:00.0: setting latency timer to 64
>> alloc irq_desc for 1243 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1242 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1241 on node 0
>> alloc kstat_irqs on node 0
>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
>> (XEN) Monitor-Mwait will be used to enter C-1 state
>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
>> (XEN) Monitor-Mwait will be used to enter C-2 state
>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
>> (XEN) Monitor-Mwait will be used to enter C-3 state
>> ACPI: CPU-1 (power states: C1[C1] C2[C2] C3[C3])
>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
>> (XEN) Monitor-Mwait will be used to enter C-1 state
>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
>> (XEN) Monitor-Mwait will be used to enter C-2 state
>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
>> (XEN) Monitor-Mwait will be used to enter C-3 state
>> ACPI: CPU-1 (power states: C1[C1] C2[C2] C3[C3])
>> 0000:04:00.0: eth1: (PCI Express:2.5GB/s:Width x1) 00:30:48:dd:eb:66
>> 0000:04:00.0: eth1: Intel(R) PRO/1000 Network Connection
>> 0000:04:00.0: eth1: MAC: 3, PHY: 8, PBA No: 0101ff-0ff
>> xen: registering gsi 17 triggering 0 polarity 1
>> xen_allocate_pirq: returning irq 17 for gsi 17
>> xen: --> irq=17
>> Already setup the GSI :17
>> e1000e 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
>> e1000e 0000:05:00.0: setting latency timer to 64
>> alloc irq_desc for 1240 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1239 on node 0
>> alloc kstat_irqs on node 0
>> alloc irq_desc for 1238 on node 0
>> alloc kstat_irqs on node 0
>> 0000:05:00.0: eth2: (PCI Express:2.5GB/s:Width x1) 00:30:48:dd:eb:67
>> 0000:05:00.0: eth2: Intel(R) PRO/1000 Network Connection
>> 0000:05:00.0: eth2: MAC: 3, PHY: 8, PBA No: 0101ff-0ff
>> udev: renamed network interface eth2 to eth1
>> udev: renamed network interface eth0 to eth2
>> udev: renamed network interface eth1_rename to eth0
>> mdadm: /dev/md0 is already in use.
>> Key slot 0 unlocked.
>> Key slot 0 unlocked.
>> device-mapper: multipath: version 1.1.0 loaded
>> Setting up Logical Volume Management: 14 logical volume(s) in
>> volume group "vg_lilith-raid" now active
>> [ OK ]
>> Checking filesystems
>> Checking all file systems.
>> [/sbin/fsck.ext4 (1) -- /] fsck.ext4 -a /dev/mapper/vg_lilith--raid-root
>> /dev/mapper/vg_lilith--raid-root contains a file system with errors,
>> check forced.
>> /dev/mapper/vg_lilith--raid-root: 343615/2564096 files (0.2%
>> non-contiguous), 2390774/10240000 blocks
>> [/sbin/fsck.ext4 (1) -- /boot] fsck.ext4 -a /dev/sda2
>> [/sbin/fsck.ext4 (2) -- /boot-spare] fsck.ext4 -a /dev/sdb2
>> /dev/sdb2: clean, 11/66384 files, 12695/265072 blocks
>> /dev/sda2: clean, 89/66384 files, 69878/265072 blocks
>> [/sbin/fsck.ext4 (1) -- /home] fsck.ext4 -a
>> /dev/mapper/luks-11eb0145-088a-4c13-acf4-9784e82bb1e3
>> /dev/mapper/luks-11eb0145-088a-4c13-acf4-9784e82bb1e3: clean,
>> 506715/12804096 files, 10193956/51199495 blocks
>> [/sbin/fsck.ext4 (1) -- /var] fsck.ext4 -a
>> /dev/mapper/luks-37e6b844-a112-427c-be60-ae6f4d9c5041
>> /dev/mapper/luks-37e6b844-a112-427c-be60-ae6f4d9c5041: clean,
>> 21026/5120000 files, 490586/20479495 blocks
>> [ OK ]
>> Remounting root filesystem in read-write mode: [ OK ]
>> Mounting local filesystems: EXT4-fs (sda2): mounted filesystem with
>> ordered data mode
>> SELinux: initialized (dev sda2, type ext4), uses xattr
>> EXT4-fs (sdb2): mounted filesystem with ordered data mode
>> SELinux: initialized (dev sdb2, type ext4), uses xattr
>> EXT4-fs (dm-15): mounted filesystem with ordered data mode
>> SELinux: initialized (dev dm-15, type ext4), uses xattr
>> EXT4-fs (dm-16): mounted filesystem with ordered data mode
>> SELinux: initialized (dev dm-16, type ext4), uses xattr
>> SELinux: initialized (dev xenfs, type xenfs), uses genfs_contexts
>> [ OK ]
>> Enabling local filesystem quotas: [ OK ]
>> Enabling /etc/fstab swaps: Adding 16381972k swap on
>> /dev/mapper/luks-2aac27aa-0bb6-46cc-8a7a-83af1ca296a2. Priority:-1
>> extents:1 across:16381972k
>> [ OK ]
>> SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses
>> genfs_contexts
>> Entering non-interactive startup
>> Applying Intel CPU microcode update: platform microcode: firmware:
>> requesting intel-ucode/06-1e-05
>> platform microcode: firmware: requesting intel-ucode/06-1e-05
>> platform microcode: firmware: requesting intel-ucode/06-1e-05
>> platform microcode: firmware: requesting intel-ucode/06-1e-05
>> Microcode Update Driver: v2.00<tigran@aivazian.fsnet.co.uk>, Peter Oruba
>> Microcode Update Driver: v2.00 removed.
>> Starting monitoring for VG vg_lilith-raid: 14 logical volume(s) in
>> volume group "vg_lilith-raid" monitored
>> [ OK ]
>> ip6tables: Applying firewall rules: [ OK ]
>> ip6tables: Loading additional modules: nf_conntrack_netbios_ns [ OK ]
>> Starting auditd: [ OK ]
>> Starting portreserve: [ OK ]
>> Starting system logger: [ OK ]
>> Starting irqbalance: [ OK ]
>> Starting rpcbind: [ OK ]
>> Starting mdmonitor: [ OK ]
>> Starting system message bus: [ OK ]
>> Starting Avahi daemon... [ OK ]
>> Starting NFS statd: [ OK ]
>> Starting RPC idmapd: FATAL: Module sunrpc not found.
>> FATAL: Error running install command for sunrpc
>> Error: RPC MTAB does not exist.
>> Starting cups: [ OK ]
>> Starting acpi daemon: [ OK ]
>> Starting HAL daemon: [ OK ]
>> Starting PC/SC smart card daemon (pcscd): [ OK ]
>> Retrigger failed udev events[ OK ]
>> Setting network parameters... [ OK ]
>> Starting NetworkManager daemon: [ OK ]
>> Enabling Bluetooth devices:
>> Starting sshd: [ OK ]
>> ADDRCONF(NETDEV_UP): eth2: link is not ready
>> ntpdate: Synchronizing with time server: ADDRCONF(NETDEV_UP): eth0:
>> link is not ready
>> ADDRCONF(NETDEV_UP): eth1: link is not ready
>> [FAILED]
>> Starting ntpd: [ OK ]
>> Starting abrt daemon: [ OK ]
>> usb 1-1.2: link qh8-0601/ffff8800b58ba740 start 3 [1/2 us]
>>
>> [ OK ] crond: [ OK ]
>> Enabling monthly Smolt checkin: [ OK ]
>> [ OK ] atd: [ OK ]
>> Starting libvirtd daemon: [ OK ]
>> Bridge firewalling registered
>> virbr0: starting userspace STP failed, starting kernel STP
>> e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
>> ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
>> e1000e: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
>> ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
>> e1000e: eth0 NICMbps Full Duplex, Flow Control: RX/TX
>> ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
>> SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
>> SELinux: initialized (dev proc, type proc), uses genfs_contexts
>> SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
>>
>> Fedora release 12 (Constantine)
>> Kernel 2.6.32.11 on an x86_64 (/dev/hvc0)
>>
>> lilith.goop.org login: usb usb2: usb auto-resume
>> ehci_hcd 0000:00:1d.0: resume root hub
>> hub 2-0:1.0: hub_resume
>> hub 2-0:1.0: port 1: status 0507 change 0000
>> usb 2-1: usb auto-resume
>> hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
>> ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 POWER sig=se0
>> PE CONNECT
>> usb 2-1: finish resume
>> hub 2-1:1.0: hub_resume
>> ehci_hcd 0000:00:1d.0: reused qh ffff8800bc51f6c0 schedule
>> usb 2-1: link qh256-0001/ffff8800bc51f6c0 start 1 [1/0 us]
>> hub 2-1:1.0: state 7 ports
>>
>>
>
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2010-04-08 16:58 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-04-06 22:38 New DMAR errors in Xen 4.1 Jeremy Fitzhardinge
2010-04-07 0:00 ` Jeremy Fitzhardinge
2010-04-07 2:50 ` Weidong Han
2010-04-07 8:31 ` Cui, Dexuan
2010-04-07 16:55 ` Jeremy Fitzhardinge
2010-04-08 2:32 ` Weidong Han
2010-04-08 16:58 ` Jeremy Fitzhardinge
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.