* [PATCH v4] davinci: Add MityDSP-L138/MityARM-1808 SOM support
@ 2010-07-29 11:29 Michael Williamson
2010-08-26 22:25 ` Kevin Hilman
0 siblings, 1 reply; 11+ messages in thread
From: Michael Williamson @ 2010-07-29 11:29 UTC (permalink / raw)
To: linux-arm-kernel
This patch adds support for the MityDSP-L138 and MityARM-1808 system on
module (SOM) under the registered machine "mityomapl138". These SOMs
are based on the da850 davinci CPU architecture. Information on these
SOMs may be found at http://www.mitydsp.com.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
---
This patch is against Kevin's tree, but is dependent on the following patch,
which is queued for 2.6.36:
[1] http://git.kernel.org/?p=linux/kernel/git/broonie/sound-2.6.git;a=commit;h=48519f0ae03bc7e86b3dc93e56f1334d53803770
Changes since v3 patch was submitted:
* renamed ATAG_PERIPHERALS to ATAG_MITYDSPL138
* removed unused header files
* renamed config structure items to remove camel case naming
* don't use GPIO if resources aren't acquired
* don't use device_initcall on emac config
* handle upcoming patch to platform sound config
* clean up mcasp configuration
* misc cleanup per comments
arch/arm/configs/da8xx_omapl_defconfig | 291 ++++++-
arch/arm/include/asm/setup.h | 5 +
arch/arm/mach-davinci/Kconfig | 8 +
arch/arm/mach-davinci/Makefile | 1 +
arch/arm/mach-davinci/board-mityomapl138.c | 806 ++++++++++++++++++++
.../mach-davinci/include/mach/cb-mityomapl138.h | 120 +++
arch/arm/mach-davinci/include/mach/da8xx.h | 1 +
arch/arm/mach-davinci/include/mach/uncompress.h | 1 +
8 files changed, 1190 insertions(+), 43 deletions(-)
diff --git a/arch/arm/configs/da8xx_omapl_defconfig b/arch/arm/configs/da8xx_omapl_defconfig
index e14c99c..0dd0d00 100644
--- a/arch/arm/configs/da8xx_omapl_defconfig
+++ b/arch/arm/configs/da8xx_omapl_defconfig
@@ -1,13 +1,15 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.32-rc5
-# Thu Oct 22 12:19:19 2009
+# Linux kernel version: 2.6.35-rc3
+# Tue Jul 20 08:30:23 2010
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
+# CONFIG_ARCH_USES_GETTIMEOFFSET is not set
CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_HAVE_PROC_CPU=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
@@ -20,6 +22,7 @@ CONFIG_ARCH_HAS_CPUFREQ=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_ZONE_DMA=y
+CONFIG_NEED_DMA_MAP_STATE=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
@@ -32,8 +35,16 @@ CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_CROSS_COMPILE=""
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_HAVE_KERNEL_LZO=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
+# CONFIG_KERNEL_LZO is not set
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
@@ -48,6 +59,7 @@ CONFIG_POSIX_MQUEUE_SYSCTL=y
#
CONFIG_TREE_RCU=y
# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_TINY_RCU is not set
# CONFIG_RCU_TRACE is not set
CONFIG_RCU_FANOUT=32
# CONFIG_RCU_FANOUT_EXACT is not set
@@ -55,11 +67,6 @@ CONFIG_RCU_FANOUT=32
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
-CONFIG_GROUP_SCHED=y
-CONFIG_FAIR_GROUP_SCHED=y
-# CONFIG_RT_GROUP_SCHED is not set
-CONFIG_USER_SCHED=y
-# CONFIG_CGROUP_SCHED is not set
# CONFIG_CGROUPS is not set
# CONFIG_SYSFS_DEPRECATED_V2 is not set
# CONFIG_RELAY is not set
@@ -69,6 +76,7 @@ CONFIG_INITRAMFS_SOURCE=""
CONFIG_RD_GZIP=y
# CONFIG_RD_BZIP2 is not set
# CONFIG_RD_LZMA is not set
+# CONFIG_RD_LZO is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_ANON_INODES=y
@@ -90,10 +98,14 @@ CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_PERF_USE_VMALLOC=y
#
# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLUB_DEBUG=y
CONFIG_COMPAT_BRK=y
@@ -131,14 +143,41 @@ CONFIG_LBDAF=y
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
# CONFIG_IOSCHED_DEADLINE is not set
# CONFIG_IOSCHED_CFQ is not set
-CONFIG_DEFAULT_AS=y
# CONFIG_DEFAULT_DEADLINE is not set
# CONFIG_DEFAULT_CFQ is not set
-# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_DEFAULT_NOOP=y
+CONFIG_DEFAULT_IOSCHED="noop"
+# CONFIG_INLINE_SPIN_TRYLOCK is not set
+# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK is not set
+# CONFIG_INLINE_SPIN_LOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
+# CONFIG_INLINE_SPIN_UNLOCK is not set
+# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
+# CONFIG_INLINE_SPIN_UNLOCK_IRQ is not set
+# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_READ_TRYLOCK is not set
+# CONFIG_INLINE_READ_LOCK is not set
+# CONFIG_INLINE_READ_LOCK_BH is not set
+# CONFIG_INLINE_READ_LOCK_IRQ is not set
+# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
+# CONFIG_INLINE_READ_UNLOCK is not set
+# CONFIG_INLINE_READ_UNLOCK_BH is not set
+# CONFIG_INLINE_READ_UNLOCK_IRQ is not set
+# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_WRITE_TRYLOCK is not set
+# CONFIG_INLINE_WRITE_LOCK is not set
+# CONFIG_INLINE_WRITE_LOCK_BH is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
+# CONFIG_INLINE_WRITE_UNLOCK is not set
+# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
+# CONFIG_INLINE_WRITE_UNLOCK_IRQ is not set
+# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
+# CONFIG_MUTEX_SPIN_ON_OWNER is not set
# CONFIG_FREEZER is not set
#
@@ -149,8 +188,11 @@ CONFIG_MMU=y
# CONFIG_ARCH_INTEGRATOR is not set
# CONFIG_ARCH_REALVIEW is not set
# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_VEXPRESS is not set
# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_BCMRING is not set
# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_CNS3XXX is not set
# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
@@ -159,7 +201,6 @@ CONFIG_MMU=y
# CONFIG_ARCH_STMP3XXX is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_NOMADIK is not set
# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IOP32X is not set
# CONFIG_ARCH_IOP33X is not set
@@ -167,6 +208,7 @@ CONFIG_MMU=y
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_DOVE is not set
# CONFIG_ARCH_KIRKWOOD is not set
# CONFIG_ARCH_LOKI is not set
# CONFIG_ARCH_MV78XX0 is not set
@@ -175,20 +217,27 @@ CONFIG_MMU=y
# CONFIG_ARCH_KS8695 is not set
# CONFIG_ARCH_NS9XXX is not set
# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_NUC93X is not set
# CONFIG_ARCH_PNX4008 is not set
# CONFIG_ARCH_PXA is not set
# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_SHMOBILE is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C2410 is not set
# CONFIG_ARCH_S3C64XX is not set
-# CONFIG_ARCH_S5PC1XX is not set
+# CONFIG_ARCH_S5P6440 is not set
+# CONFIG_ARCH_S5P6442 is not set
+# CONFIG_ARCH_S5PC100 is not set
+# CONFIG_ARCH_S5PV210 is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_LH7A40X is not set
# CONFIG_ARCH_U300 is not set
+# CONFIG_ARCH_U8500 is not set
+# CONFIG_ARCH_NOMADIK is not set
CONFIG_ARCH_DAVINCI=y
# CONFIG_ARCH_OMAP is not set
-# CONFIG_ARCH_BCMRING is not set
+# CONFIG_PLAT_SPEAR is not set
CONFIG_CP_INTC=y
#
@@ -205,18 +254,18 @@ CONFIG_ARCH_DAVINCI_DA830=y
CONFIG_ARCH_DAVINCI_DA850=y
CONFIG_ARCH_DAVINCI_DA8XX=y
# CONFIG_ARCH_DAVINCI_DM365 is not set
+# CONFIG_ARCH_DAVINCI_TNETV107X is not set
#
# DaVinci Board Type
#
CONFIG_MACH_DAVINCI_DA830_EVM=y
-CONFIG_DA830_UI=y
CONFIG_DA830_UI_LCD=y
# CONFIG_DA830_UI_NAND is not set
CONFIG_MACH_DAVINCI_DA850_EVM=y
-CONFIG_DA850_UI_EXP=y
CONFIG_DA850_UI_NONE=y
# CONFIG_DA850_UI_RMII is not set
+CONFIG_MACH_MITYOMAPL138=y
CONFIG_DAVINCI_MUX=y
# CONFIG_DAVINCI_MUX_DEBUG is not set
# CONFIG_DAVINCI_MUX_WARNINGS is not set
@@ -270,6 +319,7 @@ CONFIG_PREEMPT=y
CONFIG_HZ=100
CONFIG_AEABI=y
# CONFIG_OABI_COMPAT is not set
+CONFIG_ARCH_HAS_HOLES_MEMORYMODEL=y
# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
# CONFIG_HIGHMEM is not set
@@ -280,13 +330,11 @@ CONFIG_FLATMEM_MANUAL=y
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_PAGEFLAGS_EXTENDED=y
-CONFIG_SPLIT_PTLOCK_CPUS=4096
+CONFIG_SPLIT_PTLOCK_CPUS=999999
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_VIRT_TO_BUS=y
-CONFIG_HAVE_MLOCK=y
-CONFIG_HAVE_MLOCKED_PAGE_BIT=y
# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_LEDS=y
@@ -354,7 +402,6 @@ CONFIG_NET=y
# Networking options
#
CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
@@ -404,6 +451,7 @@ CONFIG_INET6_XFRM_MODE_TUNNEL=m
CONFIG_INET6_XFRM_MODE_BEET=m
# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
CONFIG_IPV6_SIT=m
+# CONFIG_IPV6_SIT_6RD is not set
CONFIG_IPV6_NDISC_NODETYPE=y
# CONFIG_IPV6_TUNNEL is not set
# CONFIG_IPV6_MULTIPLE_TABLES is not set
@@ -440,6 +488,7 @@ CONFIG_NETFILTER_ADVANCED=y
# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
+# CONFIG_L2TP is not set
# CONFIG_BRIDGE is not set
# CONFIG_NET_DSA is not set
# CONFIG_VLAN_8021Q is not set
@@ -465,10 +514,21 @@ CONFIG_NETFILTER_ADVANCED=y
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
-# CONFIG_WIRELESS is not set
+CONFIG_WIRELESS=y
+# CONFIG_CFG80211 is not set
+# CONFIG_LIB80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+
+#
+# Some wireless drivers require a rate control algorithm
+#
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
+# CONFIG_CAIF is not set
#
# Device Drivers
@@ -486,12 +546,110 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
-# CONFIG_MTD is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+# CONFIG_MTD_CHAR is not set
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_FTL=y
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_SM_FTL is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+# CONFIG_MTD_CFI_AMDSTD is not set
+CONFIG_MTD_CFI_STAA=y
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+# CONFIG_MTD_ARM_INTEGRATOR is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND_ECC=y
+# CONFIG_MTD_NAND_ECC_SMC is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+# CONFIG_MTD_SM_COMMON is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+CONFIG_MTD_NAND_DENALI_SCRATCH_REG_ADDR=0xFF108018
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+CONFIG_MTD_NAND_DAVINCI=y
+# CONFIG_MTD_ONENAND is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
# CONFIG_PARPORT is not set
CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=m
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+
+#
+# DRBD disabled because PROC_FS, INET or CONNECTOR not selected
+#
# CONFIG_BLK_DEV_NBD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=1
@@ -501,9 +659,12 @@ CONFIG_BLK_DEV_RAM_SIZE=32768
# CONFIG_ATA_OVER_ETH is not set
# CONFIG_MG_DISK is not set
CONFIG_MISC_DEVICES=y
+# CONFIG_AD525X_DPOT is not set
# CONFIG_ICS932S401 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_ISL29003 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_DS1682 is not set
# CONFIG_C2PORT is not set
#
@@ -519,6 +680,7 @@ CONFIG_HAVE_IDE=y
#
# SCSI device support
#
+CONFIG_SCSI_MOD=m
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=m
CONFIG_SCSI_DMA=y
@@ -583,6 +745,7 @@ CONFIG_LXT_PHY=y
# CONFIG_NATIONAL_PHY is not set
# CONFIG_STE10XP is not set
CONFIG_LSI_ET1011C_PHY=y
+# CONFIG_MICREL_PHY is not set
# CONFIG_FIXED_PHY is not set
# CONFIG_MDIO_BITBANG is not set
CONFIG_NET_ETHERNET=y
@@ -608,8 +771,7 @@ CONFIG_TI_DAVINCI_EMAC=y
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
CONFIG_WLAN=y
-# CONFIG_WLAN_PRE80211 is not set
-# CONFIG_WLAN_80211 is not set
+# CONFIG_HOSTAP is not set
#
# Enable WiMAX (Networking options) to see the WiMAX drivers
@@ -631,6 +793,7 @@ CONFIG_NET_POLL_CONTROLLER=y
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
# CONFIG_INPUT_POLLDEV is not set
+# CONFIG_INPUT_SPARSEKMAP is not set
#
# Userland interfaces
@@ -652,6 +815,7 @@ CONFIG_KEYBOARD_ATKBD=m
# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
CONFIG_KEYBOARD_GPIO=y
+# CONFIG_KEYBOARD_TCA6416 is not set
# CONFIG_KEYBOARD_MATRIX is not set
# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
@@ -665,6 +829,8 @@ CONFIG_KEYBOARD_XTKBD=m
CONFIG_INPUT_TOUCHSCREEN=y
# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
# CONFIG_TOUCHSCREEN_AD7879 is not set
+# CONFIG_TOUCHSCREEN_DYNAPRO is not set
+# CONFIG_TOUCHSCREEN_HAMPSHIRE is not set
# CONFIG_TOUCHSCREEN_EETI is not set
# CONFIG_TOUCHSCREEN_FUJITSU is not set
# CONFIG_TOUCHSCREEN_GUNZE is not set
@@ -680,6 +846,7 @@ CONFIG_INPUT_TOUCHSCREEN=y
# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
# CONFIG_TOUCHSCREEN_TSC2007 is not set
# CONFIG_TOUCHSCREEN_W90X900 is not set
+# CONFIG_TOUCHSCREEN_TPS6507X is not set
# CONFIG_INPUT_MISC is not set
#
@@ -689,6 +856,7 @@ CONFIG_SERIO=y
CONFIG_SERIO_SERPORT=y
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
+# CONFIG_SERIO_ALTERA_PS2 is not set
# CONFIG_GAMEPORT is not set
#
@@ -701,6 +869,7 @@ CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_N_GSM is not set
#
# Serial drivers
@@ -716,6 +885,9 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=3
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_TIMBERDALE is not set
+# CONFIG_SERIAL_ALTERA_JTAGUART is not set
+# CONFIG_SERIAL_ALTERA_UART is not set
CONFIG_UNIX98_PTYS=y
# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
CONFIG_LEGACY_PTYS=y
@@ -726,6 +898,7 @@ CONFIG_HW_RANDOM=m
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
+# CONFIG_RAMOOPS is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_COMPAT=y
@@ -743,7 +916,9 @@ CONFIG_I2C_DAVINCI=y
# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_GPIO is not set
# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_PCA_PLATFORM is not set
# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_XILINX is not set
#
# External I2C/SMBus adapter drivers
@@ -754,18 +929,10 @@ CONFIG_I2C_DAVINCI=y
#
# Other I2C/SMBus bus drivers
#
-# CONFIG_I2C_PCA_PLATFORM is not set
# CONFIG_I2C_STUB is not set
-
-#
-# Miscellaneous I2C Chip support
-#
-# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
-# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
#
@@ -780,13 +947,17 @@ CONFIG_GPIOLIB=y
#
# Memory mapped GPIO expanders:
#
+# CONFIG_GPIO_IT8761E is not set
#
# I2C GPIO expanders:
#
+# CONFIG_GPIO_MAX7300 is not set
# CONFIG_GPIO_MAX732X is not set
CONFIG_GPIO_PCA953X=y
+# CONFIG_GPIO_PCA953X_IRQ is not set
CONFIG_GPIO_PCF857X=y
+# CONFIG_GPIO_ADP5588 is not set
#
# PCI GPIO expanders:
@@ -799,6 +970,10 @@ CONFIG_GPIO_PCF857X=y
#
# AC97 GPIO expanders:
#
+
+#
+# MODULbus GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
@@ -811,42 +986,50 @@ CONFIG_WATCHDOG=y
#
# CONFIG_SOFT_WATCHDOG is not set
# CONFIG_DAVINCI_WATCHDOG is not set
+# CONFIG_MAX63XX_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
#
# Sonics Silicon Backplane
#
# CONFIG_SSB is not set
-
-#
-# Multifunction device drivers
-#
+CONFIG_MFD_SUPPORT=y
# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_88PM860X is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_MFD_ASIC3 is not set
# CONFIG_HTC_EGPIO is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_HTC_I2CPLD is not set
# CONFIG_TPS65010 is not set
+# CONFIG_TPS6507X is not set
# CONFIG_TWL4030_CORE is not set
+# CONFIG_MFD_TC35892 is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_MFD_T7L66XB is not set
# CONFIG_MFD_TC6387XB is not set
# CONFIG_MFD_TC6393XB is not set
# CONFIG_PMIC_DA903X is not set
+# CONFIG_PMIC_ADP5520 is not set
+# CONFIG_MFD_MAX8925 is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_WM8994 is not set
# CONFIG_MFD_PCF50633 is not set
-# CONFIG_AB3100_CORE is not set
+# CONFIG_ABX500_CORE is not set
CONFIG_REGULATOR=y
# CONFIG_REGULATOR_DEBUG is not set
+# CONFIG_REGULATOR_DUMMY is not set
# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
# CONFIG_REGULATOR_BQ24022 is not set
# CONFIG_REGULATOR_MAX1586 is not set
+# CONFIG_REGULATOR_MAX8649 is not set
+# CONFIG_REGULATOR_MAX8660 is not set
# CONFIG_REGULATOR_LP3971 is not set
-# CONFIG_REGULATOR_TPS65023 is not set
+CONFIG_REGULATOR_TPS65023=y
CONFIG_REGULATOR_TPS6507X=y
# CONFIG_MEDIA_SUPPORT is not set
@@ -950,10 +1133,6 @@ CONFIG_RTC_LIB=y
# CONFIG_DMADEVICES is not set
# CONFIG_AUXDISPLAY is not set
# CONFIG_UIO is not set
-
-#
-# TI VLYNQ
-#
# CONFIG_STAGING is not set
#
@@ -1033,6 +1212,22 @@ CONFIG_MISC_FILESYSTEMS=y
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+# CONFIG_JFFS2_CMODE_NONE is not set
+CONFIG_JFFS2_CMODE_PRIORITY=y
+# CONFIG_JFFS2_CMODE_SIZE is not set
+# CONFIG_JFFS2_CMODE_FAVOURLZO is not set
+# CONFIG_LOGFS is not set
CONFIG_CRAMFS=y
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
@@ -1062,6 +1257,7 @@ CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_SMB_NLS_DEFAULT is not set
+# CONFIG_CEPH_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
@@ -1184,6 +1380,7 @@ CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
+# CONFIG_LKDTM is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_SYSCTL_SYSCALL_CHECK is not set
@@ -1205,6 +1402,7 @@ CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_WORKQUEUE_TRACER is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_DYNAMIC_DEBUG is not set
+# CONFIG_ATOMIC64_SELFTEST is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
@@ -1213,6 +1411,7 @@ CONFIG_DEBUG_USER=y
CONFIG_DEBUG_ERRORS=y
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_LL is not set
+# CONFIG_OC_ETM is not set
#
# Security options
@@ -1220,7 +1419,11 @@ CONFIG_DEBUG_ERRORS=y
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITYFS is not set
-# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_DEFAULT_SECURITY_SELINUX is not set
+# CONFIG_DEFAULT_SECURITY_SMACK is not set
+# CONFIG_DEFAULT_SECURITY_TOMOYO is not set
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_DEFAULT_SECURITY=""
CONFIG_CRYPTO=y
#
@@ -1323,9 +1526,11 @@ CONFIG_CRC32=y
# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
CONFIG_DECOMPRESS_GZIP=y
CONFIG_GENERIC_ALLOCATOR=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
diff --git a/arch/arm/include/asm/setup.h b/arch/arm/include/asm/setup.h
index f392fb4..1d3a8cf 100644
--- a/arch/arm/include/asm/setup.h
+++ b/arch/arm/include/asm/setup.h
@@ -143,6 +143,11 @@ struct tag_memclk {
__u32 fmemclk;
};
+/** MityDSP-L138 peripheral configuration info,
+ * see arch/arm/mach-davinci/include/mach/cb-mityomapl138.h
+ */
+#define ATAG_MITYDSPL138 0x42000101
+
struct tag {
struct tag_header hdr;
union {
diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig
index 71f90f8..8fcf47d 100644
--- a/arch/arm/mach-davinci/Kconfig
+++ b/arch/arm/mach-davinci/Kconfig
@@ -178,6 +178,14 @@ config DA850_UI_RMII
endchoice
+config MACH_MITYOMAPL138
+ bool "Critical Link MityDSP-L138/MityARM-1808 SoM"
+ depends on ARCH_DAVINCI_DA850
+ help
+ Say Y here to select the Critical Link MityDSP-L138/MityARM-1808
+ System on Module. Information on this SoM may be found at
+ http://www.mitydsp.com.
+
config MACH_TNETV107X
bool "TI TNETV107X Reference Platform"
default ARCH_DAVINCI_TNETV107X
diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile
index eab4c0f..dfc0fc4 100644
--- a/arch/arm/mach-davinci/Makefile
+++ b/arch/arm/mach-davinci/Makefile
@@ -32,6 +32,7 @@ obj-$(CONFIG_MACH_DAVINCI_DM6467_EVM) += board-dm646x-evm.o cdce949.o
obj-$(CONFIG_MACH_DAVINCI_DM365_EVM) += board-dm365-evm.o
obj-$(CONFIG_MACH_DAVINCI_DA830_EVM) += board-da830-evm.o
obj-$(CONFIG_MACH_DAVINCI_DA850_EVM) += board-da850-evm.o
+obj-$(CONFIG_MACH_MITYOMAPL138) += board-mityomapl138.o
obj-$(CONFIG_MACH_TNETV107X) += board-tnetv107x-evm.o
# Power Management
diff --git a/arch/arm/mach-davinci/board-mityomapl138.c b/arch/arm/mach-davinci/board-mityomapl138.c
new file mode 100644
index 0000000..57a4ab4
--- /dev/null
+++ b/arch/arm/mach-davinci/board-mityomapl138.c
@@ -0,0 +1,806 @@
+/*
+ * Critical Link MityOMAP-L138 SoM
+ *
+ * Copyright (C) 2010 Critical Link LLC - http://www.criticallink.com
+ *
+ * Derived from board-da850-evm.c
+ * Original Copyrights follow:
+ *
+ * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Derived from: arch/arm/mach-davinci/board-da830-evm.c
+ * Original Copyrights follow:
+ *
+ * 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#define pr_fmt(fmt) "%s: " fmt, __func__
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/i2c.h>
+#include <linux/i2c/at24.h>
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/regulator/machine.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/setup.h>
+#include <mach/cp_intc.h>
+#include <mach/da8xx.h>
+#include <mach/nand.h>
+#include <mach/mux.h>
+#include <mach/cb-mityomapl138.h>
+#include <mach/spi.h>
+#include <mach/irqs.h>
+
+static struct tag_peripherals peripheral_config = {
+ .version = PERIPHERALS_VERSION,
+ .manufacturer = "Critical Link",
+ .enet.enet_config = ENET_CONFIG_MII,
+ .enet.mac = { 0x00, 0x50, 0xC2, 0x49, 0xDF, 0xFF },
+ .uart[0] = {
+ .enable = 0,
+ .is_console = 0,
+ .baud = 115200,
+ },
+ .uart[1] = {
+ .enable = 1,
+ .is_console = 1,
+ .baud = 115200,
+ },
+ .uart[2] = {
+ .enable = 0,
+ .is_console = 0,
+ .baud = 115200,
+ },
+ .spi[0] = {
+ .enable = 0,
+ .clkout = 0,
+ .cs_enable = { 0, 0, 0, 0, 0, 0, 0, 0},
+ .ena_enable = 0,
+ .clkrate = 0,
+ },
+ .spi[1] = {
+ .enable = 1,
+ .clkout = 1,
+ .cs_enable = { 1, 0, 0, 0, 0, 0, 0, 0},
+ .ena_enable = 0,
+ .clkrate = 30000000,
+ },
+ .lcd = {
+ .enable = 0,
+ .panel_name = "",
+ }
+};
+
+
+#define MITYOMAPL138_MDIO_FREQUENCY 2200000 /* PHY bus frequency */
+
+#define MSTPRI2_LCD_MASK 0x70000000
+#define MSTPRI2_LCD_SHIFT 28
+
+#define DA850_MMCSD_CD_PIN GPIO_TO_PIN(4, 0)
+#define DA850_MMCSD_WP_PIN GPIO_TO_PIN(4, 1)
+
+/* MityDSP-L138 includes a 256 MByte large-page NAND flash
+ * (128K blocks).
+ */
+struct mtd_partition mityomapl138_nandflash_partition[] = {
+ {
+ .name = "rootfs",
+ .offset = 0,
+ .size = SZ_128M,
+ .mask_flags = 0, /* MTD_WRITEABLE, */
+ },
+ {
+ .name = "homefs",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ .mask_flags = 0,
+ },
+};
+
+static struct davinci_nand_pdata mityomapl138_nandflash_data = {
+ .parts = mityomapl138_nandflash_partition,
+ .nr_parts = ARRAY_SIZE(mityomapl138_nandflash_partition),
+ .ecc_mode = NAND_ECC_HW,
+ .options = NAND_USE_FLASH_BBT | NAND_BUSWIDTH_16,
+ .ecc_bits = 1, /* 4 bit mode is not supported with 16 bit NAND */
+};
+
+static struct resource mityomapl138_nandflash_resource[] = {
+ {
+ .start = DA8XX_AEMIF_CS3_BASE,
+ .end = DA8XX_AEMIF_CS3_BASE + SZ_512K + 2 * SZ_1K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = DA8XX_AEMIF_CTL_BASE,
+ .end = DA8XX_AEMIF_CTL_BASE + SZ_32K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device mityomapl138_nandflash_device = {
+ .name = "davinci_nand",
+ .id = 0,
+ .dev = {
+ .platform_data = &mityomapl138_nandflash_data,
+ },
+ .num_resources = ARRAY_SIZE(mityomapl138_nandflash_resource),
+ .resource = mityomapl138_nandflash_resource,
+};
+
+static struct platform_device *mityomapl138_devices[] __initdata = {
+ &mityomapl138_nandflash_device,
+};
+
+static void __init mityomapl138_setup_nand(void)
+{
+ platform_add_devices(mityomapl138_devices,
+ ARRAY_SIZE(mityomapl138_devices));
+}
+
+static int mityomapl138_mmc_get_ro(int index)
+{
+ return gpio_get_value(DA850_MMCSD_WP_PIN);
+}
+
+static int mityomapl138_mmc_get_cd(int index)
+{
+ return !gpio_get_value(DA850_MMCSD_CD_PIN);
+}
+
+static struct davinci_mmc_config da850_mmc_config = {
+ .get_ro = mityomapl138_mmc_get_ro,
+ .get_cd = mityomapl138_mmc_get_cd,
+ .wires = 4,
+ .max_freq = 50000000,
+ .caps = MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED,
+ .version = MMC_CTLR_VERSION_2,
+};
+
+static void __init mityomapl138_setup_mmc(void)
+{
+ int ret;
+
+ ret = davinci_cfg_reg_list(da850_mmcsd0_pins);
+ if (ret) {
+ pr_warning("mmcsd0 mux setup failed: %d\n" ,ret);
+ return;
+ }
+ ret = gpio_request(DA850_MMCSD_CD_PIN, "MMC CD\n");
+ if (ret) {
+ pr_warning("can not open GPIO %d\n", DA850_MMCSD_CD_PIN);
+ return;
+ }
+ gpio_direction_input(DA850_MMCSD_CD_PIN);
+
+ ret = gpio_request(DA850_MMCSD_WP_PIN, "MMC WP\n");
+ if (ret) {
+ pr_warning("can not open GPIO %d\n", DA850_MMCSD_WP_PIN);
+ return;
+ }
+ gpio_direction_input(DA850_MMCSD_WP_PIN);
+
+ ret = da8xx_register_mmcsd0(&da850_mmc_config);
+ if (ret) {
+ pr_warning("mmcsd0 registration failed: %d\n", ret);
+ return;
+ }
+}
+
+static struct davinci_uart_config mityomapl138_uart_config __initdata = {
+ .enabled_uarts = 0x7,
+};
+
+static void __init mityomapl138_config_emac(void)
+{
+ void __iomem *cfg_chip3_base;
+ int ret;
+ u32 val;
+ struct davinci_soc_info *soc_info = &davinci_soc_info;
+ u8 rmii_en = 0;
+
+ switch (peripheral_config.enet.enet_config) {
+ case ENET_CONFIG_RMII:
+ soc_info->emac_pdata->rmii_en = 1;
+ rmii_en = 1;
+ break;
+ case ENET_CONFIG_MII:
+ soc_info->emac_pdata->rmii_en = 0;
+ rmii_en = 0;
+ break;
+ case ENET_CONFIG_NONE:
+ default:
+ pr_info("No Ethernet PHY Selected, EMAC disabled\n");
+ return; /* no enet... */
+ break;
+ }
+ memcpy(&soc_info->emac_pdata->mac_addr[0],
+ &peripheral_config.enet.mac[0], 6);
+
+ cfg_chip3_base = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);
+
+ val = __raw_readl(cfg_chip3_base);
+
+ if (rmii_en) {
+ val |= BIT(8);
+ ret = davinci_cfg_reg_list(da850_rmii_pins);
+ pr_info("RMII PHY configured, MII PHY will not be functional\n");
+ } else {
+ val &= ~BIT(8);
+ ret = davinci_cfg_reg_list(da850_cpgmac_pins);
+ pr_info("MII PHY configured, RMII PHY will not be functional\n");
+ }
+
+ if (ret) {
+ pr_warning("cpgmac/rmii mux setup failed: %d\n", ret);
+ return;
+ }
+
+ /* configure the CFGCHIP3 register for RMII or MII */
+ __raw_writel(val, cfg_chip3_base);
+
+ soc_info->emac_pdata->phy_mask = peripheral_config.enet.phy_mask ?
+ peripheral_config.enet.phy_mask : 1;
+ pr_info("setting phy_mask to %x\n", soc_info->emac_pdata->phy_mask);
+ soc_info->emac_pdata->mdio_max_freq = MITYOMAPL138_MDIO_FREQUENCY;
+
+ ret = da8xx_register_emac();
+ if (ret)
+ pr_warning("emac registration failed: %d\n", ret);
+}
+
+static struct davinci_i2c_platform_data mityomap_i2c_0_pdata = {
+ .bus_freq = 100, /* kHz */
+ .bus_delay = 0, /* usec */
+};
+
+/* TPS65023 voltage regulator support */
+
+/* 1.2V Core */
+struct regulator_consumer_supply tps65023_dcdc1_consumers[] = {
+ {
+ .supply = "cvdd",
+ },
+};
+
+/* 1.8V */
+struct regulator_consumer_supply tps65023_dcdc2_consumers[] = {
+ {
+ .supply = "usb0_vdda18",
+ },
+ {
+ .supply = "usb1_vdda18",
+ },
+ {
+ .supply = "ddr_dvdd18",
+ },
+ {
+ .supply = "sata_vddr",
+ },
+};
+
+/* 1.2V */
+struct regulator_consumer_supply tps65023_dcdc3_consumers[] = {
+ {
+ .supply = "sata_vdd",
+ },
+ {
+ .supply = "usb_cvdd",
+ },
+ {
+ .supply = "pll0_vdda",
+ },
+ {
+ .supply = "pll1_vdda",
+ },
+};
+
+/* 1.8V Aux LDO */
+struct regulator_consumer_supply tps65023_ldo1_consumers[] = {
+ {
+ .supply = "1.8v_aux",
+ },
+};
+
+/* VCC Aux (1.8 or 3.3) LDO */
+struct regulator_consumer_supply tps65023_ldo2_consumers[] = {
+ {
+ .supply = "vccaux",
+ },
+};
+
+
+struct regulator_init_data tps65023_regulator_data[] = {
+ /* dcdc1 */
+ {
+ .constraints = {
+ .min_uV = 1150000,
+ .max_uV = 1350000,
+ .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_STATUS),
+ .boot_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc1_consumers),
+ .consumer_supplies = tps65023_dcdc1_consumers,
+ },
+
+ /* dcdc2 */
+ {
+ .constraints = {
+ .min_uV = 1710000,
+ .max_uV = 1910000,
+ .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_STATUS),
+ .boot_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc2_consumers),
+ .consumer_supplies = tps65023_dcdc2_consumers,
+ },
+
+ /* dcdc3 */
+ {
+ .constraints = {
+ .min_uV = 1120000,
+ .max_uV = 1320000,
+ .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_STATUS),
+ .boot_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc3_consumers),
+ .consumer_supplies = tps65023_dcdc3_consumers,
+ },
+
+ /* ldo1 */
+ {
+ .constraints = {
+ .min_uV = 1710000,
+ .max_uV = 1890000,
+ .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_STATUS),
+ .boot_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(tps65023_ldo1_consumers),
+ .consumer_supplies = tps65023_ldo1_consumers,
+ },
+
+ /* ldo2 */
+ {
+ .constraints = {
+ .min_uV = 3140000,
+ .max_uV = 3420000,
+ .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_STATUS),
+ .boot_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(tps65023_ldo2_consumers),
+ .consumer_supplies = tps65023_ldo2_consumers,
+ },
+};
+
+
+static struct i2c_board_info __initdata mityomap_tps65023_info[] = {
+ {
+ I2C_BOARD_INFO("tps65023", 0x48),
+ .platform_data = &tps65023_regulator_data[0],
+ },
+ {
+ I2C_BOARD_INFO("24c02", 0x50),
+ },
+};
+
+static int __init pmic_tps65023_init(void)
+{
+ return i2c_register_board_info(1, mityomap_tps65023_info,
+ ARRAY_SIZE(mityomap_tps65023_info));
+}
+
+static struct davinci_spi_platform_data mityomap_spi1_pdata = {
+ .version = SPI_VERSION_2,
+ .num_chipselect = 1,
+ .wdelay = 0,
+ .odd_parity = 0,
+ .parity_enable = 0,
+ .wait_enable = 0,
+ .timer_disable = 0,
+ .clk_internal = 1,
+ .cs_hold = 1,
+ .intr_level = 0,
+ .poll_mode = 1,
+ .use_dma = 0,
+ .c2tdelay = 8,
+ .t2cdelay = 8,
+};
+
+static struct resource mityomap_spi1_resources[] = {
+ [0] = {
+ .start = 0x01F0E000,
+ .end = 0x01F0EFFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_DA8XX_SPINT1,
+ .start = IRQ_DA8XX_SPINT1,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = EDMA_CTLR_CHAN(0, 18),
+ .end = EDMA_CTLR_CHAN(0, 18),
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = EDMA_CTLR_CHAN(0, 19),
+ .end = EDMA_CTLR_CHAN(0, 19),
+ .flags = IORESOURCE_DMA,
+ },
+ [4] = {
+ .start = 1,
+ .end = 1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device mityomap_spi1_device = {
+ .name = "spi_davinci",
+ .id = 1,
+ .dev = {
+ .platform_data = &mityomap_spi1_pdata,
+ },
+ .num_resources = ARRAY_SIZE(mityomap_spi1_resources),
+ .resource = mityomap_spi1_resources,
+};
+
+/*****************************************************************************
+ * SPI Devices:
+ * SPI1_CS0: 8M Flash ST-M25P64-VME6G
+ ****************************************************************************/
+static struct mtd_partition spi_flash_partitions[] = {
+ [0] = {
+ .name = "UBL",
+ .offset = 0,
+ .size = SZ_64K,
+ .mask_flags = MTD_WRITEABLE
+ },
+ [1] = {
+ .name = "U-Boot",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_512K,
+ .mask_flags = 0,
+ },
+ [2] = {
+ .name = "Spare",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ .mask_flags = 0,
+ },
+};
+
+static struct flash_platform_data mityomap_spi_flash_data = {
+ .name = "m25p80",
+ .parts = spi_flash_partitions,
+ .nr_parts = ARRAY_SIZE(spi_flash_partitions),
+ .type = "m25p64",
+};
+
+static struct spi_board_info mityomap_spi_flash_info[] = {
+ {
+ .modalias = "m25p80",
+ .platform_data = &mityomap_spi_flash_data,
+ .mode = SPI_MODE_0,
+ .max_speed_hz = 30000000,
+ .bus_num = 1,
+ .chip_select = 0,
+ },
+};
+
+void __init mityomap_init_spi1(unsigned chipselect_mask,
+ struct spi_board_info *info, unsigned len)
+{
+ int ret;
+ ret = platform_device_register(&mityomap_spi1_device);
+ if (ret)
+ pr_warning("failed to register spi device : %d\n", ret);
+
+ ret = spi_register_board_info(info, len);
+ if (ret)
+ pr_warning("failed to register board info : %d\n", ret);
+}
+
+/* davinci da850 evm audio machine driver */
+static u8 da850_iis_serializer_direction[16];
+
+static struct snd_platform_data mityomapl138_snd_data = {
+ .tx_dma_offset = 0x2000,
+ .rx_dma_offset = 0x2000,
+ .op_mode = DAVINCI_MCASP_IIS_MODE,
+ .num_serializer = ARRAY_SIZE(da850_iis_serializer_direction),
+ .tdm_slots = 2,
+ .serial_dir = da850_iis_serializer_direction,
+ .asp_chan_q = EVENTQ_1,
+ .version = MCASP_VERSION_2,
+ .txnumevt = 0,
+ .rxnumevt = 0,
+};
+
+short mityomapl138_mcasp_pins[24] __initdata = {
+ DA850_AHCLKX, DA850_ACLKX, DA850_AFSX,
+ DA850_AHCLKR, DA850_ACLKR, DA850_AFSR,
+ DA850_AMUTE,
+};
+
+static __init void mityomapl138_setup_mcasp(void)
+{
+ int ret, i, j;
+
+ if (!peripheral_config.mcasp.enable)
+ return;
+
+ j = 7; /* start after AMUTE pin */
+ for (i = 0; i<ARRAY_SIZE(peripheral_config.mcasp.pin_mode); i++) {
+ switch (peripheral_config.mcasp.pin_mode[i]) {
+ case MCASP_PINMODE_RX:
+ mityomapl138_mcasp_pins[j++] = DA850_AXR_0-i;
+ da850_iis_serializer_direction[i] = RX_MODE;
+ mityomapl138_snd_data.rxnumevt++;
+ break;
+ case MCASP_PINMODE_TX:
+ mityomapl138_mcasp_pins[j++] = DA850_AXR_0-i;
+ da850_iis_serializer_direction[i] = TX_MODE;
+ mityomapl138_snd_data.txnumevt++;
+ break;
+ default:
+ da850_iis_serializer_direction[i] = INACTIVE_MODE;
+ break;
+ }
+ }
+ mityomapl138_mcasp_pins[j] = -1; /* terminate the list */
+ if (!mityomapl138_snd_data.rxnumevt && !mityomapl138_snd_data.txnumevt)
+ {
+ pr_warning("mcasp pinmux did not find Tx or Rx pins\n");
+ }
+
+ ret = davinci_cfg_reg_list(mityomapl138_mcasp_pins);
+ if (ret) {
+ pr_warning("mcasp mux setup failed: %d\n", ret);
+ return;
+ }
+
+ da8xx_register_mcasp(0, &mityomapl138_snd_data);
+}
+
+static const struct display_panel disp_panel = {
+ QVGA,
+ 16,
+ 16,
+ COLOR_ACTIVE,
+};
+
+static struct lcd_ctrl_config lcd_cfg = {
+ &disp_panel,
+ .ac_bias = 255,
+ .ac_bias_intrpt = 0,
+ .dma_burst_sz = 16,
+ .bpp = 16,
+ .fdd = 255,
+ .tft_alt_mode = 0,
+ .stn_565_mode = 0,
+ .mono_8bit_mode = 0,
+ .invert_line_clock = 0,
+ .invert_frm_clock = 0,
+ .sync_edge = 0,
+ .sync_ctrl = 1,
+ .raster_order = 0,
+};
+
+static struct da8xx_lcdc_platform_data sharp_lq035q7dh06_pdata = {
+ .manu_name = "sharp",
+ .controller_data = &lcd_cfg,
+ .type = "Sharp_LQ035Q7DH06",
+};
+
+static struct da8xx_lcdc_platform_data chimei_p0430wqlb_pdata = {
+ .manu_name = "ChiMei",
+ .controller_data = &lcd_cfg,
+ .type = "ChiMei_P0430WQLB",
+};
+
+static struct da8xx_lcdc_platform_data vga_640x480_pdata = {
+ .manu_name = "VGA",
+ .controller_data = &lcd_cfg,
+ .type = "vga_640x480",
+};
+
+static struct resource da8xx_lcdc_resources[] = {
+ [0] = { /* registers */
+ .start = DA8XX_LCD_CNTRL_BASE,
+ .end = DA8XX_LCD_CNTRL_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = { /* interrupt */
+ .start = IRQ_DA8XX_LCDINT,
+ .end = IRQ_DA8XX_LCDINT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device da8xx_lcdc_device = {
+ .name = "da8xx_lcdc",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(da8xx_lcdc_resources),
+ .resource = da8xx_lcdc_resources,
+ .dev = {
+ .platform_data = &sharp_lq035q7dh06_pdata,
+ },
+};
+
+static __init void mityomapl138_setup_lcd(void)
+{
+ int ret;
+
+ if (peripheral_config.lcd.enable) {
+ u32 prio;
+
+ /* set peripheral master priority up to 1 */
+ prio = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_MSTPRI2_REG));
+ prio &= ~MSTPRI2_LCD_MASK;
+ prio |= 1 << MSTPRI2_LCD_SHIFT;
+ __raw_writel(prio, DA8XX_SYSCFG0_VIRT(DA8XX_MSTPRI2_REG));
+
+ if (0 == strcmp("Sharp_LQ035Q7DH06",
+ peripheral_config.lcd.panel_name)) {
+ da8xx_lcdc_device.dev.platform_data =
+ &sharp_lq035q7dh06_pdata;
+ } else if (0 == strcmp("ChiMei_P0430WQLB",
+ peripheral_config.lcd.panel_name)) {
+ da8xx_lcdc_device.dev.platform_data =
+ &chimei_p0430wqlb_pdata;
+ } else if (0 == strcmp("vga_640x480",
+ peripheral_config.lcd.panel_name)) {
+ da8xx_lcdc_device.dev.platform_data =
+ &vga_640x480_pdata;
+ } else {
+ pr_warning("unknown LCD type : %s\n",
+ peripheral_config.lcd.panel_name);
+ return;
+ }
+
+ ret = davinci_cfg_reg_list(da850_lcdcntl_pins);
+ if (ret) {
+ pr_warning("lcd pinmux failed : %d\n", ret);
+ return;
+ }
+
+ ret = platform_device_register(&da8xx_lcdc_device);
+ } else {
+ pr_warning("no LCD device enabled\n");
+ }
+}
+
+static void __init mityomapl138_init(void)
+{
+ int ret;
+
+ ret = pmic_tps65023_init();
+ if (ret)
+ pr_warning("TPS65023 PMIC init failed: %d\n", ret);
+
+ ret = da8xx_register_edma();
+ if (ret)
+ pr_warning("edma registration failed: %d\n", ret);
+
+ ret = da8xx_register_i2c(0, &mityomap_i2c_0_pdata);
+ if (ret)
+ pr_warning("i2c0 registration failed: %d\n", ret);
+
+ ret = da8xx_register_watchdog();
+ if (ret)
+ pr_warning("watchdog registration failed: %d\n", ret);
+
+ davinci_serial_init(&mityomapl138_uart_config);
+
+ ret = da8xx_register_rtc();
+ if (ret)
+ pr_warning("rtc setup failed: %d\n", ret);
+
+ ret = da850_register_cpufreq();
+ if (ret)
+ pr_warning("cpufreq registration failed: %d\n", ret);
+
+ ret = da8xx_register_cpuidle();
+ if (ret)
+ pr_warning("cpuidle registration failed: %d\n", ret);
+
+ mityomapl138_setup_nand();
+
+ mityomap_init_spi1(1, mityomap_spi_flash_info,
+ ARRAY_SIZE(mityomap_spi_flash_info));
+
+ mityomapl138_setup_lcd();
+
+ mityomapl138_setup_mmc();
+
+ mityomapl138_config_emac();
+
+ mityomapl138_setup_mcasp();
+}
+
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+static int __init mityomapl138_console_init(void)
+{
+ return add_preferred_console("ttyS", 1, "115200");
+}
+console_initcall(mityomapl138_console_init);
+#endif
+
+static void __init mityomapl138_map_io(void)
+{
+ da850_init();
+}
+
+static int __init parse_tag_peripherals(const struct tag *tag)
+{
+ struct tag_peripherals *ptag;
+ int i, j;
+
+ ptag = (struct tag_peripherals *)&tag->u.cmdline.cmdline[0];
+ memcpy(&peripheral_config, ptag, sizeof(peripheral_config));
+ pr_info("Peripheral Config Block Found\n");
+ pr_info("Enet_Config = %d\n", peripheral_config.enet.enet_config);
+ pr_info("EMAC = %pM\n", peripheral_config.enet.mac);
+ pr_info("PHYMask = 0x%x\n", peripheral_config.enet.phy_mask);
+ if (peripheral_config.lcd.enable)
+ pr_info("LCD Configured : %s\n",
+ peripheral_config.lcd.panel_name);
+ else
+ pr_info("No LCD Configured\n");
+
+ for (i = 0; i < 3; i++) {
+ pr_info("UART[%d] : Enable=%d, Cons=%d, FlwCtl=%d, Baud=%d\n",
+ i,
+ peripheral_config.uart[i].enable,
+ peripheral_config.uart[i].is_console,
+ peripheral_config.uart[i].enable_flowctl,
+ peripheral_config.uart[i].baud);
+ }
+ for (i = 0; i < 2; i++) {
+ int mask = 0;
+ for (j = 0; j < 8; j++)
+ mask |= ((peripheral_config.spi[i].cs_enable[j]) ?
+ (1<<j) : 0);
+
+ pr_info("SPI[%d] : Enable=%d, CLKOut=%d, mask=%02X, ENA=%d,"
+ " CLKRate=%d\n", i,
+ peripheral_config.spi[i].enable,
+ peripheral_config.spi[i].clkout,
+ mask,
+ peripheral_config.spi[i].ena_enable,
+ peripheral_config.spi[i].clkrate);
+ }
+ pr_info("McASP Enable: %d\n", peripheral_config.mcasp.enable);
+ return 0;
+}
+__tagtable(ATAG_MITYDSPL138, parse_tag_peripherals);
+
+
+MACHINE_START(MITYOMAPL138, "MityDSP-L138")
+ .phys_io = IO_PHYS,
+ .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
+ .boot_params = (DA8XX_DDR_BASE + 0x100),
+ .map_io = mityomapl138_map_io,
+ .init_irq = cp_intc_init,
+ .timer = &davinci_timer,
+ .init_machine = mityomapl138_init,
+MACHINE_END
diff --git a/arch/arm/mach-davinci/include/mach/cb-mityomapl138.h b/arch/arm/mach-davinci/include/mach/cb-mityomapl138.h
new file mode 100644
index 0000000..547c876
--- /dev/null
+++ b/arch/arm/mach-davinci/include/mach/cb-mityomapl138.h
@@ -0,0 +1,120 @@
+/**
+ * Factory / Peripheral Configuration Data as provided by ATAG_PERIPHERAL
+ * for the MityDSP-L138 SOMs. (mityomapl138 machines)
+ *
+ * Copyright (C) 2010 Critical Link LLC. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#ifndef CB_MITYOMAPL138_H_
+#define CB_MITYOMAPL138_H_
+
+#define CONFIG_MAGIC_WORD 0x00BD0138
+#define CONFIG_VERSION 0x00010000
+
+#define ENET_CONFIG_NONE 1
+#define ENET_CONFIG_MII 2
+#define ENET_CONFIG_RMII 3
+
+#define CONFIG_I2C_MAGIC_WORD 0x012C0138
+#define CONFIG_I2C_VERSION 0x00010001
+
+/**
+ * Peripherals Version History
+ * 1.00 Baseline
+ * 1.01 Added McASP Configuration
+ * 1.02 Added ethernet phy mask
+ */
+#define PERIPHERALS_VERSION 0x00010002
+
+#ifndef CONFIG_MITYDSP_ENV_SIZE
+#define CONFIG_MITYDSP_ENV_SIZE (64 << 10)
+#endif
+
+#define FPGATYPE_NONE 0
+#define FPGATYPE_XC6SLX9 1
+#define FPGATYPE_XC6SLX16 2
+#define FPGATYPE_XC6SLX25 3
+#define FPGATYPE_XC6SLX45 4
+#define FPGATYPE_UNKNOWN 10000
+
+struct i2c_factory_config {
+ u32 magic_word; /** CONFIG_I2C_MAGIC_WORD */
+ u32 version; /** CONFIG_I2C_VERSION */
+ u8 mac[6]; /** mac address assigned to part */
+ u32 fpga; /** fpga installed, see above */
+ u32 spare; /** Not Used */
+ u32 serial_no; /** serial number of part */
+ char partnum[32]; /** board part number */
+};
+
+struct uart_config {
+ u8 enable; /** enable Tx/Rx */
+ u8 is_console; /** cfg as the console */
+ u8 enable_flowctl; /** cfg CTS/RTS */
+ u32 baud; /** default baud rate */
+};
+
+struct spi_config {
+ u8 enable; /** cfg dev+CLK, SIMO, SOMI pins */
+ u8 clkout; /** drive the CLK */
+ u8 cs_enable[8]; /** cfg the associated CS as output */
+ u8 ena_enable; /** cfg the ENA pin for SPI function */
+ u32 clkrate; /** default clock rate */
+ u8 spare[8];
+};
+
+struct lcd_config {
+ u8 enable;
+ u8 panel_name[32];
+};
+
+struct enet_config {
+ u32 enet_config;
+ u8 mac[6];
+ u32 phy_mask;
+ u8 spare[8];
+};
+
+#define MCASP_PINMODE_INACTIVE 0
+#define MCASP_PINMODE_TX 1
+#define MCASP_PINMODE_RX 2
+
+struct mcasp_config {
+ u8 enable;
+ u8 mode;
+ u8 pin_mode[16];
+};
+/**
+ * struct tag_peripherals is passed in via kernel ATAG_PERIPHERALS
+ */
+struct tag_peripherals {
+ u32 version; /** == PERIPHERALS_VERSION */
+ u8 manufacturer[64]; /** null terminated string indicating manufacturer */
+ struct enet_config enet; /** Enable on-board ethernet */
+ struct uart_config uart[3]; /** default UART 0,1,2 Configuration */
+ struct spi_config spi[2];
+ struct lcd_config lcd;
+ struct mcasp_config mcasp;
+};
+
+/**
+ * This structure can only be grown. You cannot make it smaller...
+ */
+struct mitydspl138_config {
+ u32 magic_word; /** == CONFIG_MAGIC_WORD */
+ u32 version; /** version of the configuration block */
+ u32 config_size; /** configuration size, in bytes */
+ struct tag_peripherals peripherals;
+};
+
+struct mitydspl138_config_block {
+ union {
+ struct mitydspl138_config config;
+ u8 space[CONFIG_MITYDSP_ENV_SIZE-sizeof(int)];
+ } data;
+ unsigned int checksum; /** summed bytes of ConfigSizeBytes */
+};
+
+#endif
diff --git a/arch/arm/mach-davinci/include/mach/da8xx.h b/arch/arm/mach-davinci/include/mach/da8xx.h
index 1b31a9a..1989316 100644
--- a/arch/arm/mach-davinci/include/mach/da8xx.h
+++ b/arch/arm/mach-davinci/include/mach/da8xx.h
@@ -41,6 +41,7 @@ extern void __iomem *da8xx_syscfg1_base;
#define DA8XX_SYSCFG0_BASE (IO_PHYS + 0x14000)
#define DA8XX_SYSCFG0_VIRT(x) (da8xx_syscfg0_base + (x))
#define DA8XX_JTAG_ID_REG 0x18
+#define DA8XX_MSTPRI2_REG 0x118
#define DA8XX_CFGCHIP0_REG 0x17c
#define DA8XX_CFGCHIP2_REG 0x184
#define DA8XX_CFGCHIP3_REG 0x188
diff --git a/arch/arm/mach-davinci/include/mach/uncompress.h b/arch/arm/mach-davinci/include/mach/uncompress.h
index 15a6192..db6f1cd 100644
--- a/arch/arm/mach-davinci/include/mach/uncompress.h
+++ b/arch/arm/mach-davinci/include/mach/uncompress.h
@@ -88,6 +88,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
/* DA8xx boards */
DEBUG_LL_DA8XX(davinci_da830_evm, 2);
DEBUG_LL_DA8XX(davinci_da850_evm, 2);
+ DEBUG_LL_DA8XX(mityomapl138, 1);
/* TNETV107x boards */
DEBUG_LL_TNETV107X(tnetv107x, 1);
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v4] davinci: Add MityDSP-L138/MityARM-1808 SOM support
2010-07-29 11:29 [PATCH v4] davinci: Add MityDSP-L138/MityARM-1808 SOM support Michael Williamson
@ 2010-08-26 22:25 ` Kevin Hilman
2010-08-27 0:12 ` Michael Williamson
0 siblings, 1 reply; 11+ messages in thread
From: Kevin Hilman @ 2010-08-26 22:25 UTC (permalink / raw)
To: linux-arm-kernel
Michael Williamson <michael.williamson@criticallink.com> writes:
> This patch adds support for the MityDSP-L138 and MityARM-1808 system on
> module (SOM) under the registered machine "mityomapl138". These SOMs
> are based on the da850 davinci CPU architecture. Information on these
> SOMs may be found at http://www.mitydsp.com.
>
> Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
> ---
> This patch is against Kevin's tree, but is dependent on the following patch,
> which is queued for 2.6.36:
>
> [1] http://git.kernel.org/?p=linux/kernel/git/broonie/sound-2.6.git;a=commit;h=48519f0ae03bc7e86b3dc93e56f1334d53803770
Running this patch through scripts/checkpatch.pl, I get:
total: 268 errors, 586 warnings, 1632 lines checked
Please fix all errors and warnings.
For future reference, normally, I don't even read the rest of a patch if
there are any checkpatch errors.
> Changes since v3 patch was submitted:
> * renamed ATAG_PERIPHERALS to ATAG_MITYDSPL138
This new ATAG should be a separate patch.
However, as I mentioned in earlier versions, new ATAGs are not welcome
upstream, and I will not merge this. Other suggestions have been
proposed to solve this.
If you insist, after the bare board support is merged, you can post your
ATAG patch to linux-arm-kernel and see if Russell is willing to merge
this, but I doubt it.
> * removed unused header files
> * renamed config structure items to remove camel case naming
> * don't use GPIO if resources aren't acquired
> * don't use device_initcall on emac config
> * handle upcoming patch to platform sound config
> * clean up mcasp configuration
> * misc cleanup per comments
>
> arch/arm/configs/da8xx_omapl_defconfig | 291 ++++++-
The defconfig change needs to be redone against current tree, since some
major changes where done here for 2.6.36.
> arch/arm/include/asm/setup.h | 5 +
> arch/arm/mach-davinci/Kconfig | 8 +
> arch/arm/mach-davinci/Makefile | 1 +
> arch/arm/mach-davinci/board-mityomapl138.c | 806 ++++++++++++++++++++
> .../mach-davinci/include/mach/cb-mityomapl138.h | 120 +++
> arch/arm/mach-davinci/include/mach/da8xx.h | 1 +
> arch/arm/mach-davinci/include/mach/uncompress.h | 1 +
> 8 files changed, 1190 insertions(+), 43 deletions(-)
Normally, I like to see new board support broken down more. It's rather
difficult to do a good review of new board file when everything is added
in a single patch.
Typically, a basic patch that just supports basic boot (typically to
UART console) is the first patch. Then additional patches are added to
add peripheral support (display, MMC, SPI, flash, regulators, ...)
Breaking things up this way helps reviewers and maintainers greatly.
[...]
> diff --git a/arch/arm/include/asm/setup.h b/arch/arm/include/asm/setup.h
> index f392fb4..1d3a8cf 100644
> --- a/arch/arm/include/asm/setup.h
> +++ b/arch/arm/include/asm/setup.h
> @@ -143,6 +143,11 @@ struct tag_memclk {
> __u32 fmemclk;
> };
>
> +/** MityDSP-L138 peripheral configuration info,
please fix multi-line comment style. search for 'multi-line' in
Documentation/CodingStytle. There are several instances of this problem
in the patch.
> + * see arch/arm/mach-davinci/include/mach/cb-mityomapl138.h
> + */
> +#define ATAG_MITYDSPL138 0x42000101
> +
> struct tag {
> struct tag_header hdr;
> union {
> diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig
> index 71f90f8..8fcf47d 100644
> --- a/arch/arm/mach-davinci/Kconfig
> +++ b/arch/arm/mach-davinci/Kconfig
> @@ -178,6 +178,14 @@ config DA850_UI_RMII
>
> endchoice
>
> +config MACH_MITYOMAPL138
> + bool "Critical Link MityDSP-L138/MityARM-1808 SoM"
> + depends on ARCH_DAVINCI_DA850
> + help
> + Say Y here to select the Critical Link MityDSP-L138/MityARM-1808
> + System on Module. Information on this SoM may be found at
> + http://www.mitydsp.com.
> +
> config MACH_TNETV107X
> bool "TI TNETV107X Reference Platform"
> default ARCH_DAVINCI_TNETV107X
> diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile
> index eab4c0f..dfc0fc4 100644
> --- a/arch/arm/mach-davinci/Makefile
> +++ b/arch/arm/mach-davinci/Makefile
> @@ -32,6 +32,7 @@ obj-$(CONFIG_MACH_DAVINCI_DM6467_EVM) += board-dm646x-evm.o cdce949.o
> obj-$(CONFIG_MACH_DAVINCI_DM365_EVM) += board-dm365-evm.o
> obj-$(CONFIG_MACH_DAVINCI_DA830_EVM) += board-da830-evm.o
> obj-$(CONFIG_MACH_DAVINCI_DA850_EVM) += board-da850-evm.o
> +obj-$(CONFIG_MACH_MITYOMAPL138) += board-mityomapl138.o
> obj-$(CONFIG_MACH_TNETV107X) += board-tnetv107x-evm.o
>
> # Power Management
> diff --git a/arch/arm/mach-davinci/board-mityomapl138.c b/arch/arm/mach-davinci/board-mityomapl138.c
> new file mode 100644
> index 0000000..57a4ab4
> --- /dev/null
> +++ b/arch/arm/mach-davinci/board-mityomapl138.c
> @@ -0,0 +1,806 @@
> +/*
> + * Critical Link MityOMAP-L138 SoM
> + *
> + * Copyright (C) 2010 Critical Link LLC - http://www.criticallink.com
> + *
> + * Derived from board-da850-evm.c
> + * Original Copyrights follow:
> + *
> + * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com/
> + *
> + * Derived from: arch/arm/mach-davinci/board-da830-evm.c
> + * Original Copyrights follow:
> + *
> + * 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
> + * the terms of the GNU General Public License version 2. This program
> + * is licensed "as is" without any warranty of any kind, whether express
> + * or implied.
> + */
> +
> +#define pr_fmt(fmt) "%s: " fmt, __func__
I don't find any users of this in the patch. Please remove.
> +#include <linux/kernel.h>
> +#include <linux/init.h>
> +#include <linux/console.h>
> +#include <linux/i2c.h>
> +#include <linux/i2c/at24.h>
I don't think you need at24.h here. Please remove any headers that you
are not actually using.
[...]
Kevin
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v4] davinci: Add MityDSP-L138/MityARM-1808 SOM support
2010-08-26 22:25 ` Kevin Hilman
@ 2010-08-27 0:12 ` Michael Williamson
2010-08-27 11:12 ` Michael Williamson
2010-08-27 14:11 ` Kevin Hilman
0 siblings, 2 replies; 11+ messages in thread
From: Michael Williamson @ 2010-08-27 0:12 UTC (permalink / raw)
To: linux-arm-kernel
Hi Kevin,
On 08/26/2010 06:25 PM, Kevin Hilman wrote:
> Michael Williamson<michael.williamson@criticallink.com> writes:
>
>
>> This patch adds support for the MityDSP-L138 and MityARM-1808 system on
>> module (SOM) under the registered machine "mityomapl138". These SOMs
>> are based on the da850 davinci CPU architecture. Information on these
>> SOMs may be found at http://www.mitydsp.com.
>>
>> Signed-off-by: Michael Williamson<michael.williamson@criticallink.com>
>> ---
>> This patch is against Kevin's tree, but is dependent on the following patch,
>> which is queued for 2.6.36:
>>
>> [1] http://git.kernel.org/?p=linux/kernel/git/broonie/sound-2.6.git;a=commit;h=48519f0ae03bc7e86b3dc93e56f1334d53803770
>>
> Running this patch through scripts/checkpatch.pl, I get:
>
> total: 268 errors, 586 warnings, 1632 lines checked
>
> Please fix all errors and warnings.
>
> For future reference, normally, I don't even read the rest of a patch if
> there are any checkpatch errors.
>
>
As expected. At the time I submitted this (before your comments came in
on V3, actually), I had run a checkpatch.pl and it had passed. That was
prior to the 2.6.35 merge when you got back from vacation. Given your
comments on V3, I had withdrawn the submission. This submission should
have been dropped. I'm sorry if I generated extra reviewing work for you.
I didn't catch that our thread of discussion was on the V3 submission.
Please drop all submissions relating to this subject. If there was
something
more I should have done, please let me know.
>> Changes since v3 patch was submitted:
>> * renamed ATAG_PERIPHERALS to ATAG_MITYDSPL138
>>
> This new ATAG should be a separate patch.
>
> However, as I mentioned in earlier versions, new ATAGs are not welcome
> upstream, and I will not merge this. Other suggestions have been
> proposed to solve this.
>
> If you insist, after the bare board support is merged, you can post your
> ATAG patch to linux-arm-kernel and see if Russell is willing to merge
> this, but I doubt it.
>
Understood. Not trying to use this ATAG patch for the mainline anymore,
trying other techniques but not ready for resubmission.
>
>> * removed unused header files
>> * renamed config structure items to remove camel case naming
>> * don't use GPIO if resources aren't acquired
>> * don't use device_initcall on emac config
>> * handle upcoming patch to platform sound config
>> * clean up mcasp configuration
>> * misc cleanup per comments
>>
>> arch/arm/configs/da8xx_omapl_defconfig | 291 ++++++-
>>
> The defconfig change needs to be redone against current tree, since some
> major changes where done here for 2.6.36.
>
I saw that go by. If I get around to a resubmission, I'll be sure to
sync up.
>
>> arch/arm/include/asm/setup.h | 5 +
>> arch/arm/mach-davinci/Kconfig | 8 +
>> arch/arm/mach-davinci/Makefile | 1 +
>> arch/arm/mach-davinci/board-mityomapl138.c | 806 ++++++++++++++++++++
>> .../mach-davinci/include/mach/cb-mityomapl138.h | 120 +++
>> arch/arm/mach-davinci/include/mach/da8xx.h | 1 +
>> arch/arm/mach-davinci/include/mach/uncompress.h | 1 +
>> 8 files changed, 1190 insertions(+), 43 deletions(-)
>>
> Normally, I like to see new board support broken down more. It's rather
> difficult to do a good review of new board file when everything is added
> in a single patch.
>
> Typically, a basic patch that just supports basic boot (typically to
> UART console) is the first patch. Then additional patches are added to
> add peripheral support (display, MMC, SPI, flash, regulators, ...)
>
> Breaking things up this way helps reviewers and maintainers greatly.
>
> [...]
>
OK. Most of the board file is a large cut-and-paste of the da850
EVM. It seems unlikely that I'll have any measure of success here, but if
I get time I might try again.
>
>> diff --git a/arch/arm/include/asm/setup.h b/arch/arm/include/asm/setup.h
>> index f392fb4..1d3a8cf 100644
>> --- a/arch/arm/include/asm/setup.h
>> +++ b/arch/arm/include/asm/setup.h
>> @@ -143,6 +143,11 @@ struct tag_memclk {
>> __u32 fmemclk;
>> };
>>
>> +/** MityDSP-L138 peripheral configuration info,
>>
> please fix multi-line comment style. search for 'multi-line' in
> Documentation/CodingStytle. There are several instances of this problem
> in the patch.
>
>
OK. I'll watch for that if I resubmit. Thanks.
>> + * see arch/arm/mach-davinci/include/mach/cb-mityomapl138.h
>> + */
>> +#define ATAG_MITYDSPL138 0x42000101
>> +
>> struct tag {
>> struct tag_header hdr;
>> union {
>> diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig
>> index 71f90f8..8fcf47d 100644
>> --- a/arch/arm/mach-davinci/Kconfig
>> +++ b/arch/arm/mach-davinci/Kconfig
>> @@ -178,6 +178,14 @@ config DA850_UI_RMII
>>
>> endchoice
>>
>> +config MACH_MITYOMAPL138
>> + bool "Critical Link MityDSP-L138/MityARM-1808 SoM"
>> + depends on ARCH_DAVINCI_DA850
>> + help
>> + Say Y here to select the Critical Link MityDSP-L138/MityARM-1808
>> + System on Module. Information on this SoM may be found at
>> + http://www.mitydsp.com.
>> +
>> config MACH_TNETV107X
>> bool "TI TNETV107X Reference Platform"
>> default ARCH_DAVINCI_TNETV107X
>> diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile
>> index eab4c0f..dfc0fc4 100644
>> --- a/arch/arm/mach-davinci/Makefile
>> +++ b/arch/arm/mach-davinci/Makefile
>> @@ -32,6 +32,7 @@ obj-$(CONFIG_MACH_DAVINCI_DM6467_EVM) += board-dm646x-evm.o cdce949.o
>> obj-$(CONFIG_MACH_DAVINCI_DM365_EVM) += board-dm365-evm.o
>> obj-$(CONFIG_MACH_DAVINCI_DA830_EVM) += board-da830-evm.o
>> obj-$(CONFIG_MACH_DAVINCI_DA850_EVM) += board-da850-evm.o
>> +obj-$(CONFIG_MACH_MITYOMAPL138) += board-mityomapl138.o
>> obj-$(CONFIG_MACH_TNETV107X) += board-tnetv107x-evm.o
>>
>> # Power Management
>> diff --git a/arch/arm/mach-davinci/board-mityomapl138.c b/arch/arm/mach-davinci/board-mityomapl138.c
>> new file mode 100644
>> index 0000000..57a4ab4
>> --- /dev/null
>> +++ b/arch/arm/mach-davinci/board-mityomapl138.c
>> @@ -0,0 +1,806 @@
>> +/*
>> + * Critical Link MityOMAP-L138 SoM
>> + *
>> + * Copyright (C) 2010 Critical Link LLC - http://www.criticallink.com
>> + *
>> + * Derived from board-da850-evm.c
>> + * Original Copyrights follow:
>> + *
>> + * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com/
>> + *
>> + * Derived from: arch/arm/mach-davinci/board-da830-evm.c
>> + * Original Copyrights follow:
>> + *
>> + * 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
>> + * the terms of the GNU General Public License version 2. This program
>> + * is licensed "as is" without any warranty of any kind, whether express
>> + * or implied.
>> + */
>> +
>> +#define pr_fmt(fmt) "%s: " fmt, __func__
>>
> I don't find any users of this in the patch. Please remove.
>
>
OK. Thanks (I had another comment recommending I use that).
>> +#include<linux/kernel.h>
>> +#include<linux/init.h>
>> +#include<linux/console.h>
>> +#include<linux/i2c.h>
>> +#include<linux/i2c/at24.h>
>>
> I don't think you need at24.h here. Please remove any headers that you
> are not actually using.
>
> [...]
>
> Kevin
>
Thanks.
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v4] davinci: Add MityDSP-L138/MityARM-1808 SOM support
2010-08-27 0:12 ` Michael Williamson
@ 2010-08-27 11:12 ` Michael Williamson
2010-08-27 14:11 ` Kevin Hilman
1 sibling, 0 replies; 11+ messages in thread
From: Michael Williamson @ 2010-08-27 11:12 UTC (permalink / raw)
To: linux-arm-kernel
On 08/26/2010 08:12 PM, Michael Williamson wrote:
> Hi Kevin,
>
> On 08/26/2010 06:25 PM, Kevin Hilman wrote:
>> Michael Williamson<michael.williamson@criticallink.com> writes:
>>
>>> This patch adds support for the MityDSP-L138 and MityARM-1808
>>> system on
>>> module (SOM) under the registered machine "mityomapl138". These SOMs
>>> are based on the da850 davinci CPU architecture. Information on these
>>> SOMs may be found at http://www.mitydsp.com.
>>>
>>> Signed-off-by: Michael Williamson<michael.williamson@criticallink.com>
>>> ---
>>> This patch is against Kevin's tree, but is dependent on the
>>> following patch,
>>> which is queued for 2.6.36:
>>>
>>> [1]
>>> http://git.kernel.org/?p=linux/kernel/git/broonie/sound-2.6.git;a=commit;h=48519f0ae03bc7e86b3dc93e56f1334d53803770
>>>
>> Running this patch through scripts/checkpatch.pl, I get:
>>
>> total: 268 errors, 586 warnings, 1632 lines checked
>>
>> Please fix all errors and warnings.
>>
>> For future reference, normally, I don't even read the rest of a patch if
>> there are any checkpatch errors.
>>
>
> As expected. At the time I submitted this (before your comments came in
> on V3, actually), I had run a checkpatch.pl and it had passed. That was
> prior to the 2.6.35 merge when you got back from vacation.
That should have read 2.6.36. I also must have blown the checkpatch as
well.
-Mike
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v4] davinci: Add MityDSP-L138/MityARM-1808 SOM support
2010-08-27 0:12 ` Michael Williamson
2010-08-27 11:12 ` Michael Williamson
@ 2010-08-27 14:11 ` Kevin Hilman
2010-08-27 16:24 ` Michael Williamson
1 sibling, 1 reply; 11+ messages in thread
From: Kevin Hilman @ 2010-08-27 14:11 UTC (permalink / raw)
To: linux-arm-kernel
Michael Williamson <michael.williamson@criticallink.com> writes:
>> Normally, I like to see new board support broken down more. It's rather
>> difficult to do a good review of new board file when everything is added
>> in a single patch.
>>
>> Typically, a basic patch that just supports basic boot (typically to
>> UART console) is the first patch. Then additional patches are added to
>> add peripheral support (display, MMC, SPI, flash, regulators, ...)
>>
>> Breaking things up this way helps reviewers and maintainers greatly.
>>
>> [...]
>>
> OK. Most of the board file is a large cut-and-paste of the da850
> EVM. It seems unlikely that I'll have any measure of success here, but if
> I get time I might try again.
OK, if it's mostly a cut-and-paste of da850, then maybe just break it up
into two patches, 1) the cut, paste & rename patch and 2) a separate
patch for things that are different on your board.
Thanks,
Kevin
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v4] davinci: Add MityDSP-L138/MityARM-1808 SOM support
2010-08-27 14:11 ` Kevin Hilman
@ 2010-08-27 16:24 ` Michael Williamson
2010-08-27 18:05 ` Kevin Hilman
0 siblings, 1 reply; 11+ messages in thread
From: Michael Williamson @ 2010-08-27 16:24 UTC (permalink / raw)
To: linux-arm-kernel
On 08/27/2010 10:11 AM, Kevin Hilman wrote:
> Michael Williamson<michael.williamson@criticallink.com> writes:
>
>
>>> Normally, I like to see new board support broken down more. It's rather
>>> difficult to do a good review of new board file when everything is added
>>> in a single patch.
>>>
>>> Typically, a basic patch that just supports basic boot (typically to
>>> UART console) is the first patch. Then additional patches are added to
>>> add peripheral support (display, MMC, SPI, flash, regulators, ...)
>>>
>>> Breaking things up this way helps reviewers and maintainers greatly.
>>>
>>> [...]
>>>
>>>
>> OK. Most of the board file is a large cut-and-paste of the da850
>> EVM. It seems unlikely that I'll have any measure of success here, but if
>> I get time I might try again.
>>
> OK, if it's mostly a cut-and-paste of da850, then maybe just break it up
> into two patches, 1) the cut, paste& rename patch and 2) a separate
> patch for things that are different on your board.
>
> Thanks,
>
> Kevin
>
I think I am going to try again. I intend to basically start over, leaving
the console UART, NAND, and EMAC (hardcoded to MII interface for now).
This is the minimum set of devices I need to get one of our base boards to
boot and mount a root filesystem and run some tests here.
I will remove all the ATAG garbage and anything that is runtime configurable
as well as the LCD, McASP, SPI, SPI-NOR, and I2C based peripherals. If the
patch is OK, then I'll add them back one by one for review.
Would this be a reasonable approach? And should I post it as a v5 to this
series or create a different series (given the large change of code)?
Should I pull the general ARM mailing list off the distribution as this
should
now be specific only to mach-davinci?
Thanks again for any insight.
-Mike
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v4] davinci: Add MityDSP-L138/MityARM-1808 SOM support
2010-08-27 16:24 ` Michael Williamson
@ 2010-08-27 18:05 ` Kevin Hilman
2010-08-28 13:26 ` mmc over SPI on DM6467 based board. card not detected Sumesh Kaana
0 siblings, 1 reply; 11+ messages in thread
From: Kevin Hilman @ 2010-08-27 18:05 UTC (permalink / raw)
To: linux-arm-kernel
Michael Williamson <michael.williamson@criticallink.com> writes:
> On 08/27/2010 10:11 AM, Kevin Hilman wrote:
>> Michael Williamson<michael.williamson@criticallink.com> writes:
>>
>>
>>>> Normally, I like to see new board support broken down more. It's rather
>>>> difficult to do a good review of new board file when everything is added
>>>> in a single patch.
>>>>
>>>> Typically, a basic patch that just supports basic boot (typically to
>>>> UART console) is the first patch. Then additional patches are added to
>>>> add peripheral support (display, MMC, SPI, flash, regulators, ...)
>>>>
>>>> Breaking things up this way helps reviewers and maintainers greatly.
>>>>
>>>> [...]
>>>>
>>>>
>>> OK. Most of the board file is a large cut-and-paste of the da850
>>> EVM. It seems unlikely that I'll have any measure of success here, but if
>>> I get time I might try again.
>>>
>> OK, if it's mostly a cut-and-paste of da850, then maybe just break it up
>> into two patches, 1) the cut, paste& rename patch and 2) a separate
>> patch for things that are different on your board.
>>
>> Thanks,
>>
>> Kevin
>>
>
> I think I am going to try again. I intend to basically start over, leaving
> the console UART, NAND, and EMAC (hardcoded to MII interface for now).
> This is the minimum set of devices I need to get one of our base boards to
> boot and mount a root filesystem and run some tests here.
>
> I will remove all the ATAG garbage and anything that is runtime configurable
> as well as the LCD, McASP, SPI, SPI-NOR, and I2C based peripherals. If the
> patch is OK, then I'll add them back one by one for review.
>
> Would this be a reasonable approach?
Yes, perfect!
> And should I post it as a v5 to this
> series or create a different series (given the large change of code)?
A new series is fine.
> Should I pull the general ARM mailing list off the distribution as
> this should now be specific only to mach-davinci?
Keeping linux-arm-kernel in copy is good.
Kevin
^ permalink raw reply [flat|nested] 11+ messages in thread
* mmc over SPI on DM6467 based board. card not detected.
2010-08-27 18:05 ` Kevin Hilman
@ 2010-08-28 13:26 ` Sumesh Kaana
2010-08-30 13:27 ` Steve Chen
2010-09-02 14:18 ` Jassi Brar
0 siblings, 2 replies; 11+ messages in thread
From: Sumesh Kaana @ 2010-08-28 13:26 UTC (permalink / raw)
To: linux-arm-kernel
Hi all,
I am trying to mount SD-Card over SPI on our custom DM6467
board. davinci spi controller driver and mmc over spi drver are selected in the menuconfig. i am using davinci-PSP.03-XX-00-37 kernel.
I have also edited board initialization file to probe the MMC card under SPI as below:
static struct spi_board_info
dm646x_spi_info[] __initconst = {
#ifdef CONFIG_MMC_SPI
{
.modalias = "mmc_spi",
.max_speed_hz = (750 * 1000 ), /* max spi clock (SCK)
speed in HZ */
.bus_num = 0,
.chip_select =
0,
/* CS0 */
.mode = SPI_MODE_0,
},
#endif
The kernel boots with following log
spi_davinci spi_davinci.0: DaVinci
SPI driver in EDMA mode
Using RX channel = 17 , TX channel =
16 and event queue = 3
spi_davinci spi_davinci.0:
Controller at 0xfec66800
?????
????..
mmc_spi spi0.0: ASSUMING SPI bus
stays unshared!
mmc_spi spi0.0: ASSUMING 3.2-3.4 V
slot power
mmc0: clock 0Hz busmode 0 powermode
0 cs 0 Vdd 0 width 0 timing 0
mmc_spi spi0.0: SD/MMC host mmc0, no
WP, no poweroff
mmc0: clock 0Hz busmode 2 powermode
1 cs 1 Vdd 21 width 0 timing 0
mmc_spi spi0.0: mmc_spi: power up
(21)
mmc0: Minimum clock frequency too
high for identification mode
mmc0: clock 750000Hz busmode 2
powermode 2 cs 1 Vdd 21 width 0 timing 0
mmc_spi spi0.0: mmc_spi: power on
(21)
mmc_spi spi0.0: can't change
chip-select polarity 1
mmc0: starting CMD52 arg 80000c08
flags 00000015
mmc_spi spi0.0: bogus command
Backtrace:
[<c002a7d0>]
(dump_backtrace+0x0/0x114) from [<c023f5e4>] (dump_stack+0x18/0x1c)
r7:ce0bf400 r6:ce0bf400
r5:ce0bf5c0 r4:00000000
[<c023f5cc>]
(dump_stack+0x0/0x1c) from [<c01af3f0>] (mmc_spi_request+0xa8/0x9d8)
[<c01af348>]
(mmc_spi_request+0x0/0x9d8) from [<c01a75f8>]
(mmc_wait_for_req+0x1f4/0x21c)
[<c01a7404>]
(mmc_wait_for_req+0x0/0x21c) from [<c01a768c>] (mmc_wait_for_cmd+0x6c/0x7c)
r7:00000000 r6:ce0bf400
r5:ce091f1c r4:ce091ee4
[<c01a7620>]
(mmc_wait_for_cmd+0x0/0x7c) from [<c01ab4f0>] (mmc_reset_sdio+0x5c/0x6c)
r7:ce090000 r6:ce0bf550
r5:ce0bf400 r4:ce091f1c
[<c01ab494>]
(mmc_reset_sdio+0x0/0x6c) from [<c01a71f0>] (mmc_rescan+0x24c/0x2ec)
r5:60000013 r4:ce0bf400
[<c01a6fa4>]
(mmc_rescan+0x0/0x2ec) from [<c004eb28>] (worker_thread+0x138/0x1f8)
r6:ce092de0 r5:ce0bf550
r4:ce0bf554
[<c004e9f0>]
(worker_thread+0x0/0x1f8) from [<c0052904>] (kthread+0x88/0x90)
[<c005287c>] (kthread+0x0/0x90)
from [<c003f9b8>] (do_exit+0x0/0x684)
r7:00000000 r6:00000000
r5:00000000 r4:00000000
mmc0: req done (CMD52): -22:
00000000 00000000 00000000 00000000
mmc0: starting CMD0 arg 00000000
flags 000000c0
mmc_spi spi0.0: mmc_spi:
CMD0, resp R1
I am not able to identify the micro SD card. Is there
anything which i am missing?
Regards,
Sumesh.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20100828/1ca3b06c/attachment-0001.html>
^ permalink raw reply [flat|nested] 11+ messages in thread
* mmc over SPI on DM6467 based board. card not detected.
2010-08-28 13:26 ` mmc over SPI on DM6467 based board. card not detected Sumesh Kaana
@ 2010-08-30 13:27 ` Steve Chen
2010-09-01 11:41 ` Martin Guy
2010-09-02 14:18 ` Jassi Brar
1 sibling, 1 reply; 11+ messages in thread
From: Steve Chen @ 2010-08-30 13:27 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, Aug 28, 2010 at 8:26 AM, Sumesh Kaana <sumeshkkn@hotmail.com> wrote:
> Hi all,
>
>
>
> I am trying to mount SD-Card over SPI on our custom DM6467 board. davinci
> spi controller driver and mmc over spi drver are selected in the menuconfig.
> i am using davinci-PSP.03-XX-00-37 kernel.
>
> I have also edited board initialization file to probe the MMC card under SPI
> as below:
>
>
>
> static struct spi_board_info dm646x_spi_info[] __initconst = {
>
> #ifdef CONFIG_MMC_SPI
>
> ??????? {
>
> ??????????????? .modalias = "mmc_spi",
>
> ??????????????? .max_speed_hz = (750 * 1000 ),???? /* max spi clock (SCK)
> speed in HZ */
>
> ??????????????? .bus_num = 0,
>
> ??????????????? .chip_select = 0,?????????????????????? /* CS0 */
>
> ??????????????? .mode?????????? = SPI_MODE_0,
>
> ??????? },
>
> #endif
>
>
>
> The kernel boots with following log
>
...
> mmc0: Minimum clock frequency too high for identification mode
...
Have you tried lower the clock frequency?
Steve
^ permalink raw reply [flat|nested] 11+ messages in thread
* mmc over SPI on DM6467 based board. card not detected.
2010-08-30 13:27 ` Steve Chen
@ 2010-09-01 11:41 ` Martin Guy
0 siblings, 0 replies; 11+ messages in thread
From: Martin Guy @ 2010-09-01 11:41 UTC (permalink / raw)
To: linux-arm-kernel
On 8/30/10, Steve Chen <schen@mvista.com> wrote:
> On Sat, Aug 28, 2010 at 8:26 AM, Sumesh Kaana <sumeshkkn@hotmail.com> wrote:
> > I am trying to mount SD-Card over SPI on our custom DM6467 board. davinci
> > spi controller driver and mmc over spi drver are selected in the menuconfig.
> > i am using davinci-PSP.03-XX-00-37 kernel.
> >
> > I have also edited board initialization file to probe the MMC card under SPI
> > as below:
> >
> >
> >
> > static struct spi_board_info dm646x_spi_info[] __initconst = {
> >
> > #ifdef CONFIG_MMC_SPI
> >
> > {
> >
> > .modalias = "mmc_spi",
> >
> > .max_speed_hz = (750 * 1000 ), /* max spi clock (SCK)
> > speed in HZ */
> >
> > .bus_num = 0,
> >
> > .chip_select = 0, /* CS0 */
> >
> > .mode = SPI_MODE_0,
> >
> > },
> >
> > #endif
> >
> >
> >
> > The kernel boots with following log
> >
> ...
> > mmc0: Minimum clock frequency too high for identification mode
> ...
>
> Have you tried lower the clock frequency?
The initial card identification should be done at 400kHz. If that is
successful, the following commands can be sent at your maximum rate.
M
^ permalink raw reply [flat|nested] 11+ messages in thread
* mmc over SPI on DM6467 based board. card not detected.
2010-08-28 13:26 ` mmc over SPI on DM6467 based board. card not detected Sumesh Kaana
2010-08-30 13:27 ` Steve Chen
@ 2010-09-02 14:18 ` Jassi Brar
1 sibling, 0 replies; 11+ messages in thread
From: Jassi Brar @ 2010-09-02 14:18 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, Aug 28, 2010 at 10:26 PM, Sumesh Kaana <sumeshkkn@hotmail.com> wrote:
> Hi all,
>
>
>
> I am trying to mount SD-Card over SPI on our custom DM6467 board. davinci
> spi controller driver and mmc over spi drver are selected in the menuconfig.
> i am using davinci-PSP.03-XX-00-37 kernel.
>
> I have also edited board initialization file to probe the MMC card under SPI
> as below:
First, make sure
a) you provide 3.3v and ground properly.
b) the slot, card and connections are OK by using spi_gpio driver to
run the same pins,
if the SPI controller pins could be muxed into GPIO mode(usually
they could be).
Probably the source clock doesn't allow for scaling down to within
400KHz, give it a closer look.
^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2010-09-02 14:18 UTC | newest]
Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-07-29 11:29 [PATCH v4] davinci: Add MityDSP-L138/MityARM-1808 SOM support Michael Williamson
2010-08-26 22:25 ` Kevin Hilman
2010-08-27 0:12 ` Michael Williamson
2010-08-27 11:12 ` Michael Williamson
2010-08-27 14:11 ` Kevin Hilman
2010-08-27 16:24 ` Michael Williamson
2010-08-27 18:05 ` Kevin Hilman
2010-08-28 13:26 ` mmc over SPI on DM6467 based board. card not detected Sumesh Kaana
2010-08-30 13:27 ` Steve Chen
2010-09-01 11:41 ` Martin Guy
2010-09-02 14:18 ` Jassi Brar
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.