* 5x dom0 memory increase from Xen/Linux 3.4/2.6.18 to 4.1/3.0.0
@ 2011-06-16 12:58 Anthony Wright
2011-06-16 14:56 ` Konrad Rzeszutek Wilk
0 siblings, 1 reply; 10+ messages in thread
From: Anthony Wright @ 2011-06-16 12:58 UTC (permalink / raw)
To: xen-devel
I have a fairly old machine with 512M of RAM that I use for testing. Under Xen 3.4 with the 2.6.18 linux kernel it would happily work with dom0_mem=50M, leaving 450M for VMs. I am in the process of upgrading to Xen 4.1 with a stock 3.0.0-rc3 linux kernel (with konrad's vga-support patch). This combination however requires dom0_mem=250M to work leaving only 250M for the VMs (if I try to set dom0_mem any lower I get a kernel panic early on in the kernel boot phase).
This is an increase of 5x between the two versions, and I wondered if there's an explanation why. Is it possible to reduce the memory requirements, or do I have to learn to live with it.
thanks,
Anthony Wright
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 5x dom0 memory increase from Xen/Linux 3.4/2.6.18 to 4.1/3.0.0
2011-06-16 12:58 5x dom0 memory increase from Xen/Linux 3.4/2.6.18 to 4.1/3.0.0 Anthony Wright
@ 2011-06-16 14:56 ` Konrad Rzeszutek Wilk
2011-06-17 15:31 ` Anthony Wright
0 siblings, 1 reply; 10+ messages in thread
From: Konrad Rzeszutek Wilk @ 2011-06-16 14:56 UTC (permalink / raw)
To: Anthony Wright; +Cc: xen-devel
On Thu, Jun 16, 2011 at 01:58:25PM +0100, Anthony Wright wrote:
> I have a fairly old machine with 512M of RAM that I use for testing. Under Xen 3.4 with the 2.6.18 linux kernel it would happily work with dom0_mem=50M, leaving 450M for VMs. I am in the process of upgrading to Xen 4.1 with a stock 3.0.0-rc3 linux kernel (with konrad's vga-support patch). This combination however requires dom0_mem=250M to work leaving only 250M for the VMs (if I try to set dom0_mem any lower I get a kernel panic early on in the kernel boot phase).
>
> This is an increase of 5x between the two versions, and I wondered if there's an explanation why. Is it possible to reduce the memory requirements, or do I have to learn to live with it.
The SWIOTLB is taking a 64MB chunk out of it. You could lower that by 'swiotlb=2048' or so.
Also make sure to compile the CONFIG_XEN_MAX_DOMAIN_MEMORY from 128GB down to say 1.
Besides that .. run with 'memblock=debug loglevel=10 initcall_debug debug' and see what other
regions memblock reserves that could be shrunk.
>
> thanks,
>
> Anthony Wright
>
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 5x dom0 memory increase from Xen/Linux 3.4/2.6.18 to 4.1/3.0.0
2011-06-16 14:56 ` Konrad Rzeszutek Wilk
@ 2011-06-17 15:31 ` Anthony Wright
2011-06-20 12:45 ` Konrad Rzeszutek Wilk
0 siblings, 1 reply; 10+ messages in thread
From: Anthony Wright @ 2011-06-17 15:31 UTC (permalink / raw)
To: Konrad Rzeszutek Wilk; +Cc: xen-devel
Lowering swiotlb helped, and got me down to 200M for dom0. What is the effect of reducing this value?
I set CONFIG_XEN_MAX_DOMAIN_MEMORY down to 8, but that didn't seem to have any effect on dom0's memory requirement. What is this value? Does it only apply to a domU's memory usage?
I tried the memblock=debug options, and while I got lots of output, I could see very little on the subject of memory usage.
I'm at 4x memory usage, which is better, but I'd really like to understand where all the memory's going.
thanks,
Anthony.
----- Original Message -----
From: "Konrad Rzeszutek Wilk" <konrad.wilk@oracle.com>
To: "Anthony Wright" <anthony@overnetdata.com>
Cc: xen-devel@lists.xensource.com
Sent: Thursday, 16 June, 2011 3:56:11 PM
Subject: Re: [Xen-devel] 5x dom0 memory increase from Xen/Linux 3.4/2.6.18 to 4.1/3.0.0
On Thu, Jun 16, 2011 at 01:58:25PM +0100, Anthony Wright wrote:
> I have a fairly old machine with 512M of RAM that I use for testing. Under Xen 3.4 with the 2.6.18 linux kernel it would happily work with dom0_mem=50M, leaving 450M for VMs. I am in the process of upgrading to Xen 4.1 with a stock 3.0.0-rc3 linux kernel (with konrad's vga-support patch). This combination however requires dom0_mem=250M to work leaving only 250M for the VMs (if I try to set dom0_mem any lower I get a kernel panic early on in the kernel boot phase).
>
> This is an increase of 5x between the two versions, and I wondered if there's an explanation why. Is it possible to reduce the memory requirements, or do I have to learn to live with it.
The SWIOTLB is taking a 64MB chunk out of it. You could lower that by 'swiotlb=2048' or so.
Also make sure to compile the CONFIG_XEN_MAX_DOMAIN_MEMORY from 128GB down to say 1.
Besides that .. run with 'memblock=debug loglevel=10 initcall_debug debug' and see what other
regions memblock reserves that could be shrunk.
>
> thanks,
>
> Anthony Wright
>
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 5x dom0 memory increase from Xen/Linux 3.4/2.6.18 to 4.1/3.0.0
2011-06-17 15:31 ` Anthony Wright
@ 2011-06-20 12:45 ` Konrad Rzeszutek Wilk
2011-06-22 13:15 ` Anthony Wright
0 siblings, 1 reply; 10+ messages in thread
From: Konrad Rzeszutek Wilk @ 2011-06-20 12:45 UTC (permalink / raw)
To: Anthony Wright; +Cc: xen-devel
On Fri, Jun 17, 2011 at 04:31:11PM +0100, Anthony Wright wrote:
> Lowering swiotlb helped, and got me down to 200M for dom0. What is the effect of reducing this value?
Less amount of bounce buffer. But you don't need the bounce buffer for PCI devices b/c you don't
have more than 4GB of physical memory in the machine.
>
> I set CONFIG_XEN_MAX_DOMAIN_MEMORY down to 8, but that didn't seem to have any effect on dom0's memory requirement. What is this value? Does it only apply to a domU's memory usage?
It makes some internal datastructures (P2M) smaller. They are set up for 128GB or so machines initially.
>
> I tried the memblock=debug options, and while I got lots of output, I could see very little on the subject of memory usage.
The numbers are what amount of memory is reserved. You can find out which are are is eating the most
by computing the difference.
>
> I'm at 4x memory usage, which is better, but I'd really like to understand where all the memory's going.
Me too.
>
> thanks,
>
> Anthony.
>
>
> ----- Original Message -----
> From: "Konrad Rzeszutek Wilk" <konrad.wilk@oracle.com>
> To: "Anthony Wright" <anthony@overnetdata.com>
> Cc: xen-devel@lists.xensource.com
> Sent: Thursday, 16 June, 2011 3:56:11 PM
> Subject: Re: [Xen-devel] 5x dom0 memory increase from Xen/Linux 3.4/2.6.18 to 4.1/3.0.0
>
> On Thu, Jun 16, 2011 at 01:58:25PM +0100, Anthony Wright wrote:
> > I have a fairly old machine with 512M of RAM that I use for testing. Under Xen 3.4 with the 2.6.18 linux kernel it would happily work with dom0_mem=50M, leaving 450M for VMs. I am in the process of upgrading to Xen 4.1 with a stock 3.0.0-rc3 linux kernel (with konrad's vga-support patch). This combination however requires dom0_mem=250M to work leaving only 250M for the VMs (if I try to set dom0_mem any lower I get a kernel panic early on in the kernel boot phase).
>
> >
> > This is an increase of 5x between the two versions, and I wondered if there's an explanation why. Is it possible to reduce the memory requirements, or do I have to learn to live with it.
>
> The SWIOTLB is taking a 64MB chunk out of it. You could lower that by 'swiotlb=2048' or so.
> Also make sure to compile the CONFIG_XEN_MAX_DOMAIN_MEMORY from 128GB down to say 1.
>
> Besides that .. run with 'memblock=debug loglevel=10 initcall_debug debug' and see what other
> regions memblock reserves that could be shrunk.
> >
> > thanks,
> >
> > Anthony Wright
> >
> >
> > _______________________________________________
> > Xen-devel mailing list
> > Xen-devel@lists.xensource.com
> > http://lists.xensource.com/xen-devel
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 5x dom0 memory increase from Xen/Linux 3.4/2.6.18 to 4.1/3.0.0
2011-06-20 12:45 ` Konrad Rzeszutek Wilk
@ 2011-06-22 13:15 ` Anthony Wright
2011-06-22 13:32 ` Konrad Rzeszutek Wilk
0 siblings, 1 reply; 10+ messages in thread
From: Anthony Wright @ 2011-06-22 13:15 UTC (permalink / raw)
To: Konrad Rzeszutek Wilk; +Cc: xen-devel
[-- Attachment #1: Type: text/plain, Size: 1583 bytes --]
On 20/06/2011 13:45, Konrad Rzeszutek Wilk wrote:
> On Fri, Jun 17, 2011 at 04:31:11PM +0100, Anthony Wright wrote:
>> Lowering swiotlb helped, and got me down to 200M for dom0. What is the effect of reducing this value?
> Less amount of bounce buffer. But you don't need the bounce buffer for PCI devices b/c you don't
> have more than 4GB of physical memory in the machine.
Do I only need bounce buffers if I have > 4GB of physical memory? In
this case should I allocate the 64M, or is it a sliding memory requirement?
>> I set CONFIG_XEN_MAX_DOMAIN_MEMORY down to 8, but that didn't seem to have any effect on dom0's memory requirement. What is this value? Does it only apply to a domU's memory usage?
> It makes some internal datastructures (P2M) smaller. They are set up for 128GB or so machines initially.
It sounds like this value applies to DomUs, does this config variables
set the maximum amount of memory 128GB per DomU or across all DomUs,
i.e. if I have 16 DomUs and a CONFIG_XEN_MAX_DOMAIN_MEMORY of 16, do
they each have a maximum of 16GB, or do the get 1GB each?
>> I tried the memblock=debug options, and while I got lots of output, I could see very little on the subject of memory usage.
> The numbers are what amount of memory is reserved. You can find out which are are is eating the most
> by computing the difference.
Maybe I'm misreading the output, but I couldn't see any numbers that
look like memory being assigned. I've attached the dmesg output. Do I
need to enable a CONFIG variable to get the output I need or am I
missing something.
thanks,
Anthony.
[-- Attachment #2: dmesg - memory debug --]
[-- Type: text/plain, Size: 296326 bytes --]
7>[ 2.250546] calling opti_init+0x0/0x11 @ 1
[ 2.250546] initcall opti_init+0x0/0x11 returned 0 after 641 usecs
[ 2.250546] calling pcmcia_init+0x0/0xa @ 1
[ 2.250546] initcall pcmcia_init+0x0/0xa returned 0 after 566 usecs
[ 2.250546] calling qdi_init+0x0/0x1b4 @ 1
[ 2.250546] initcall qdi_init+0x0/0x1b4 returned -19 after 2 usecs
[ 2.250546] calling rz1000_init+0x0/0x11 @ 1
[ 2.250546] initcall rz1000_init+0x0/0x11 returned 0 after 611 usecs
[ 2.250546] calling pacpi_init+0x0/0x11 @ 1
[ 2.260243] initcall pacpi_init+0x0/0x11 returned 0 after 1086 usecs
[ 2.260404] calling ata_generic_init+0x0/0x11 @ 1
[ 2.260404] initcall ata_generic_init+0x0/0x11 returned 0 after 689 usecs
[ 2.260404] calling legacy_init+0x0/0x866 @ 1
[ 2.260404] initcall legacy_init+0x0/0x866 returned -19 after 56 usecs
[ 2.260404] calling init_mtd+0x0/0xa0 @ 1
[ 2.260404] initcall init_mtd+0x0/0xa0 returned 0 after 2455 usecs
[ 2.260404] calling redboot_parser_init+0x0/0xa @ 1
[ 2.260404] initcall redboot_parser_init+0x0/0xa returned 0 after 1 usecs
[ 2.260404] calling ar7_parser_init+0x0/0xa @ 1
[ 2.260404] initcall ar7_parser_init+0x0/0xa returned 0 after 1 usecs
[ 2.260404] calling init_mtdchar+0x0/0xad @ 1
[ 2.260404] initcall init_mtdchar+0x0/0xad returned 0 after 138 usecs
[ 2.260404] calling init_mtdblock+0x0/0x1e @ 1
[ 2.260404] initcall init_mtdblock+0x0/0x1e returned 0 after 4 usecs
[ 2.260404] calling init_ftl+0x0/0xa @ 1
[ 2.260404] initcall init_ftl+0x0/0xa returned 0 after 2 usecs
[ 2.260404] calling init_nftl+0x0/0xa @ 1
[ 2.260404] initcall init_nftl+0x0/0xa returned 0 after 2 usecs
[ 2.260404] calling init_inftl+0x0/0xa @ 1
[ 2.260404] initcall init_inftl+0x0/0xa returned 0 after 2 usecs
[ 2.260404] calling init_rfd_ftl+0x0/0xa @ 1
[ 2.260404] initcall init_rfd_ftl+0x0/0xa returned 0 after 3 usecs
[ 2.260404] calling init_ssfdcr+0x0/0x15 @ 1
[ 2.260404] SSFDC read-only Flash Translation layer
[ 2.260404] initcall init_ssfdcr+0x0/0x15 returned 0 after 192 usecs
[ 2.260404] calling mtdoops_init+0x0/0xfe @ 1
[ 2.260404] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 2.260404] initcall mtdoops_init+0x0/0xfe returned -22 after 194 usecs
[ 2.260404] initcall mtdoops_init+0x0/0xfe returned with error code -22
[ 2.260404] calling cfi_probe_init+0x0/0xd @ 1
[ 2.260404] initcall cfi_probe_init+0x0/0xd returned 0 after 3 usecs
[ 2.260404] calling jedec_probe_init+0x0/0xd @ 1
[ 2.260404] initcall jedec_probe_init+0x0/0xd returned 0 after 1 usecs
[ 2.260404] calling map_ram_init+0x0/0xd @ 1
[ 2.260404] initcall map_ram_init+0x0/0xd returned 0 after 1 usecs
[ 2.260404] calling map_rom_init+0x0/0xd @ 1
[ 2.260404] initcall map_rom_init+0x0/0xd returned 0 after 1 usecs
[ 2.260404] calling map_absent_init+0x0/0xd @ 1
[ 2.260404] initcall map_absent_init+0x0/0xd returned 0 after 1 usecs
[ 2.260404] calling init_esb2rom+0x0/0x56c @ 1
[ 2.260404] device id = 2440
[ 2.260404] device id = 2480
[ 2.260404] device id = 24c0
[ 2.260404] device id = 24d0
[ 2.260404] device id = 25a1
[ 2.260404] device id = 2670
[ 2.260404] initcall init_esb2rom+0x0/0x56c returned -6 after 1107 usecs
[ 2.260404] initcall init_esb2rom+0x0/0x56c returned with error code -6
[ 2.260404] calling init_ck804xrom+0x0/0x480 @ 1
[ 2.260404] initcall init_ck804xrom+0x0/0x480 returned -6 after 43 usecs
[ 2.260404] initcall init_ck804xrom+0x0/0x480 returned with error code -6
[ 2.260404] calling init_sc520cdp+0x0/0x1fc @ 1
[ 2.274952] Could not find PAR responsible for SC520CDP Flash Bank #0
[ 2.275168] Trying default address 0x8400000
[ 2.275416] Could not find PAR responsible for SC520CDP Flash Bank #1
[ 2.275618] Trying default address 0x8c00000
[ 2.275825] Could not find PAR responsible for SC520CDP DIL Flash
[ 2.275825] Trying default address 0x9400000
[ 2.275825] SC520 CDP flash device: 0x800000 at 0x8400000
[ 2.275825] Failed to ioremap_nocache
[ 2.275825] initcall init_sc520cdp+0x0/0x1fc returned -5 after 1981 usecs
[ 2.275825] initcall init_sc520cdp+0x0/0x1fc returned with error code -5
[ 2.275825] calling init_netsc520+0x0/0xda @ 1
[ 2.275825] NetSc520 flash device: 0x100000 at 0x200000
[ 2.275825] Failed to ioremap_nocache
[ 2.275825] initcall init_netsc520+0x0/0xda returned -5 after 382 usecs
[ 2.275825] initcall init_netsc520+0x0/0xda returned with error code -5
[ 2.275825] calling init_ts5500_map+0x0/0x9b @ 1
[ 2.275825] Failed to ioremap_nocache
[ 2.275825] initcall init_ts5500_map+0x0/0x9b returned -5 after 189 usecs
[ 2.275825] initcall init_ts5500_map+0x0/0x9b returned with error code -5
[ 2.275825] calling mtd_pci_maps_init+0x0/0x11 @ 1
[ 2.280321] initcall mtd_pci_maps_init+0x0/0x11 returned 0 after 1311 usecs
[ 2.280321] calling scb2_flash_init+0x0/0x11 @ 1
[ 2.280321] initcall scb2_flash_init+0x0/0x11 returned 0 after 736 usecs
[ 2.280321] calling init_pmc551+0x0/0x5aa @ 1
[ 2.280321] Ramix PMC551 PCI Mezzanine Ram Driver. (C) 1999,2000 Nortel Networks.
[ 2.280321] pmc551: not detected
[ 2.280321] initcall init_pmc551+0x0/0x5aa returned -19 after 511 usecs
[ 2.280321] calling init_mtdram+0x0/0x90 @ 1
[ 2.290157] ftl_cs: FTL header not found.
[ 2.320162] initcall init_mtdram+0x0/0x90 returned 0 after 40647 usecs
[ 2.320162] calling block2mtd_init+0x0/0x27 @ 1
[ 2.320162] initcall block2mtd_init+0x0/0x27 returned 0 after 2 usecs
[ 2.320162] calling nand_base_init+0x0/0x12 @ 1
[ 2.320162] initcall nand_base_init+0x0/0x12 returned 0 after 305 usecs
[ 2.320162] calling cafe_nand_init+0x0/0x11 @ 1
[ 2.320162] initcall cafe_nand_init+0x0/0x11 returned 0 after 933 usecs
[ 2.320162] calling init_nanddoc+0x0/0x9b @ 1
[ 2.320162] Possible DiskOnChip at 0xca000 failed TOGGLE test, dropping.
[ 2.320162] No valid DiskOnChip devices found
[ 2.320162] initcall init_nanddoc+0x0/0x9b returned -19 after 575 usecs
[ 2.320162] calling ns_init_module+0x0/0xc8f @ 1
[ 2.329211] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0
[ 2.329532] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0
[ 2.330144] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0
[ 2.330144] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0
[ 2.330144] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0
[ 2.330144] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0
[ 2.330144] NAND device: Manufacturer ID: 0x98, Chip ID: 0x39 (Toshiba NAND 128MiB 1,8V 8-bit)
[ 2.330144] flash size: 128 MiB
[ 2.330144] page size: 512 bytes
[ 2.330144] OOB area size: 16 bytes
[ 2.330144] sector size: 16 KiB
[ 2.330144] pages number: 262144
[ 2.330144] pages per sector: 32
[ 2.330144] bus width: 8
[ 2.330144] bits in sector size: 14
[ 2.330144] bits in page size: 9
[ 2.330144] bits in OOB size: 4
[ 2.330144] flash size with OOB: 135168 KiB
[ 2.330144] page address bytes: 4
[ 2.330144] sector address bytes: 3
[ 2.330144] options: 0x62
[ 2.340128] Scanning device for bad blocks
[ 2.440062] Creating 1 MTD partitions on "NAND 128MiB 1,8V 8-bit":
[ 2.440062] 0x000000000000-0x000008000000 : "NAND simulator partition 0"
[ 2.440062] ata2.00: ATAPI: SAMSUNG CD-ROM SC-148F, F007, max UDMA/33
[ 2.450130] ata2.00: configured for UDMA/33
[ 2.450130] async_waiting @ 5
[ 2.450130] ftl_cs: FTL header not found.
[ 2.450130] initcall ns_init_module+0x0/0xc8f returned 0 after 122607 usecs
[ 2.450130] calling cs553x_init+0x0/0x2a3 @ 1
[ 2.450130] initcall cs553x_init+0x0/0x2a3 returned -6 after 1 usecs
[ 2.450130] initcall cs553x_init+0x0/0x2a3 returned with error code -6
[ 2.450130] calling alauda_init+0x0/0x11 @ 1
[ 2.450130] usbcore: registered new interface driver alauda
[ 2.450130] initcall alauda_init+0x0/0x11 returned 0 after 903 usecs
[ 2.450130] calling ubi_init+0x0/0x279 @ 1
[ 2.450130] initcall ubi_init+0x0/0x279 returned 0 after 1241 usecs
[ 2.450130] calling marvell_init+0x0/0x44 @ 1
[ 2.460150] initcall marvell_init+0x0/0x44 returned 0 after 4770 usecs
[ 2.460150] calling davicom_init+0x0/0x49 @ 1
[ 2.460150] initcall davicom_init+0x0/0x49 returned 0 after 1298 usecs
[ 2.460150] calling cicada_init+0x0/0x2f @ 1
[ 2.460150] initcall cicada_init+0x0/0x2f returned 0 after 889 usecs
[ 2.460150] calling lxt_init+0x0/0x49 @ 1
[ 2.460150] initcall lxt_init+0x0/0x49 returned 0 after 1347 usecs
[ 2.460150] calling qs6612_init+0x0/0xa @ 1
[ 2.470173] initcall qs6612_init+0x0/0xa returned 0 after 933 usecs
[ 2.470366] calling smsc_init+0x0/0x7d @ 1
[ 2.470366] initcall smsc_init+0x0/0x7d returned 0 after 2158 usecs
[ 2.470366] calling vsc82xx_init+0x0/0x2f @ 1
[ 2.470366] initcall vsc82xx_init+0x0/0x2f returned 0 after 901 usecs
[ 2.470366] calling broadcom_init+0x0/0x131 @ 1
[ 2.470366] ata1.00: ATA-5: IBM-DTLA-307045, TX6OA60A, max UDMA/100
[ 2.470366] ata1.00: 90069840 sectors, multi 8: LBA
[ 2.480127] initcall broadcom_init+0x0/0x131 returned 0 after 7751 usecs
[ 2.480127] calling icplus_init+0x0/0x1e @ 1
[ 2.480127] initcall icplus_init+0x0/0x1e returned 0 after 899 usecs
[ 2.480127] calling realtek_init+0x0/0xa @ 1
[ 2.480127] initcall realtek_init+0x0/0xa returned 0 after 472 usecs
[ 2.480127] calling e1000_init_module+0x0/0x68 @ 1
[ 2.480127] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[ 2.480127] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 2.480127] initcall e1000_init_module+0x0/0x68 returned 0 after 1078 usecs
[ 2.480127] calling e1000_init_module+0x0/0x2d @ 1
[ 2.480127] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.10-k2
[ 2.480127] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[ 2.480127] initcall e1000_init_module+0x0/0x2d returned 0 after 1017 usecs
[ 2.480127] calling igb_init_module+0x0/0x41 @ 1
[ 2.480127] Intel(R) Gigabit Ethernet Network Driver - version 3.0.6-k2
[ 2.480127] Copyright (c) 2007-2011 Intel Corporation.
[ 2.489978] initcall igb_init_module+0x0/0x41 returned 0 after 1393 usecs
[ 2.490153] calling igbvf_init_module+0x0/0x37 @ 1
[ 2.490153] Intel(R) Virtual Function Network Driver - version 1.0.8-k0
[ 2.490153] Copyright (c) 2009 - 2010 Intel Corporation.
[ 2.490153] initcall igbvf_init_module+0x0/0x37 returned 0 after 1061 usecs
[ 2.490153] calling ixgbe_init_module+0x0/0x41 @ 1
[ 2.490153] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 3.3.8-k2
[ 2.490153] ixgbe: Copyright (c) 1999-2011 Intel Corporation.
[ 2.490153] initcall ixgbe_init_module+0x0/0x41 returned 0 after 1153 usecs
[ 2.490153] calling ixgbevf_init_module+0x0/0x37 @ 1
[ 2.490153] ixgbevf: Intel(R) 10 Gigabit PCI Express Virtual Function Network Driver - version 2.0.0-k2
[ 2.490153] Copyright (c) 2009 - 2010 Intel Corporation.
[ 2.490153] initcall ixgbevf_init_module+0x0/0x37 returned 0 after 1160 usecs
[ 2.490153] calling ixgb_init_module+0x0/0x37 @ 1
[ 2.490153] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI
[ 2.490153] ixgb: Copyright (c) 1999-2008 Intel Corporation.
[ 2.490153] initcall ixgb_init_module+0x0/0x37 returned 0 after 1059 usecs
[ 2.490153] calling ipg_init_module+0x0/0x11 @ 1
[ 2.490153] initcall ipg_init_module+0x0/0x11 returned 0 after 779 usecs
[ 2.490153] calling t1_init_module+0x0/0x11 @ 1
[ 2.490153] initcall t1_init_module+0x0/0x11 returned 0 after 751 usecs
[ 2.490153] calling cxgb3_init_module+0x0/0x16 @ 1
[ 2.500845] initcall cxgb3_init_module+0x0/0x16 returned 0 after 1534 usecs
[ 2.500845] calling bonding_init+0x0/0x7b1 @ 1
[ 2.500845] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 2.500845] bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details.
[ 2.510166] initcall bonding_init+0x0/0x7b1 returned 0 after 16379 usecs
[ 2.510166] calling atl1_init_module+0x0/0x11 @ 1
[ 2.520146] initcall atl1_init_module+0x0/0x11 returned 0 after 2026 usecs
[ 2.520146] calling atl2_init_module+0x0/0x37 @ 1
[ 2.520146] Atheros(R) L2 Ethernet Driver - version 2.2.3
[ 2.520146] Copyright (c) 2007 Atheros Corporation.
[ 2.520146] initcall atl2_init_module+0x0/0x37 returned 0 after 1119 usecs
[ 2.520146] calling atl1e_init_module+0x0/0x11 @ 1
[ 2.520146] initcall atl1e_init_module+0x0/0x11 returned 0 after 1409 usecs
[ 2.520146] calling atl1c_init_module+0x0/0x11 @ 1
[ 2.520146] ata1.00: configured for UDMA/66
[ 2.520146] async_waiting @ 11
[ 2.520146] async_continuing @ 11 after 2 usec
[ 2.520146] scsi 2:0:0:0: Direct-Access ATA IBM-DTLA-307045 TX6O PQ: 0 ANSI: 5
[ 2.520146] initcall atl1c_init_module+0x0/0x11 returned 0 after 3080 usecs
[ 2.520146] calling bdx_module_init+0x0/0x69 @ 1
[ 2.520146] tehuti: Tehuti Networks(R) Network Driver, 7.29.3
[ 2.520146] tehuti: Options: hw_csum
[ 2.530132] initcall bdx_module_init+0x0/0x69 returned 0 after 2057 usecs
[ 2.530132] calling enic_init_module+0x0/0x28 @ 1
[ 2.530132] enic: Cisco VIC Ethernet NIC Driver, ver 2.1.1.13
[ 2.530132] initcall enic_init_module+0x0/0x28 returned 0 after 1604 usecs
[ 2.530132] calling jme_init_module+0x0/0x22 @ 1
[ 2.530132] jme: JMicron JMC2XX ethernet driver version 1.0.8
[ 2.530132] calling 4_sd_probe_async+0x0/0x184 @ 1285
[ 2.530132] initcall jme_init_module+0x0/0x22 returned 0 after 1948 usecs
[ 2.530132] calling be_init_module+0x0/0x3d @ 1
[ 2.530132] sd 2:0:0:0: [sda] 90069840 512-byte logical blocks: (46.1 GB/42.9 GiB)
[ 2.530132] sd 2:0:0:0: [sda] Write Protect is off
[ 2.530132] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.530132] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.540158] initcall be_init_module+0x0/0x3d returned 0 after 4478 usecs
[ 2.540158] calling bnad_module_init+0x0/0x49 @ 1
[ 2.540158] Brocade 10G Ethernet driver
[ 2.540158] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 2.540158] initcall bnad_module_init+0x0/0x49 returned 0 after 4224 usecs
[ 2.540158] calling happy_meal_probe+0x0/0x11 @ 1
[ 2.540158] initcall 2_async_port_probe+0x0/0x43 returned 0 after 346988 usecs
[ 2.540158] async_continuing @ 5 after 92824 usec
[ 2.540158] scsi 3:0:0:0: CD-ROM SAMSUNG CD-ROM SC-148F F007 PQ: 0 ANSI: 5
[ 2.549547] initcall happy_meal_probe+0x0/0x11 returned 0 after 3808 usecs
[ 2.549794] calling gem_init+0x0/0x11 @ 1
[ 2.550143] initcall gem_init+0x0/0x11 returned 0 after 1591 usecs
[ 2.550143] calling cas_init+0x0/0x31 @ 1
[ 2.550143] initcall cas_init+0x0/0x31 returned 0 after 2122 usecs
[ 2.550143] calling vortex_init+0x0/0x8f @ 1
[ 2.550143] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
[ 2.550143] xen: registering gsi 5 triggering 0 polarity 1
[ 2.550143] xen_map_pirq_gsi: returning irq 5 for gsi 5
[ 2.550143] xen: --> pirq=5 -> irq=5
[ 2.550143] Failed to setup GSI :5, err_code:-22
[ 2.550143] 3c59x 0000:01:0c.0: PCI INT A -> Link[LNKC] -> GSI 5 (level, low) -> IRQ 5
[ 2.550143] 3c59x: Donald Becker and others.
[ 2.550143] 0000:01:0c.0: 3Com PCI 3c905C Tornado at edc2a800.
[ 2.580049] sda: sda1 sda2
[ 2.580049] sr0: scsi3-mmc drive: 1x/48x cd/rw xa/form2 cdda tray
[ 2.580049] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.580049] sd 2:0:0:0: [sda] Attached SCSI disk
[ 2.580049] initcall 4_sd_probe_async+0x0/0x184 returned 0 after 52675 usecs
[ 2.590380] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 2.590380] initcall vortex_init+0x0/0x8f returned 0 after 37109 usecs
[ 2.590380] calling typhoon_init+0x0/0x11 @ 1
[ 2.590380] initcall typhoon_init+0x0/0x11 returned 0 after 1852 usecs
[ 2.590380] calling ne2k_pci_init+0x0/0x11 @ 1
[ 2.590380] sr 3:0:0:0: Attached scsi generic sg1 type 5
[ 2.590380] initcall ne2k_pci_init+0x0/0x11 returned 0 after 1849 usecs
[ 2.590380] calling pcnet32_init_module+0x0/0x100 @ 1
[ 2.590380] pcnet32: pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
[ 2.599612] initcall 3_async_port_probe+0x0/0x43 returned 0 after 398614 usecs
[ 2.600130] initcall pcnet32_init_module+0x0/0x100 returned 0 after 2263 usecs
[ 2.600130] calling e100_init_module+0x0/0x48 @ 1
[ 2.600130] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 2.600130] e100: Copyright(c) 1999-2006 Intel Corporation
[ 2.600130] initcall e100_init_module+0x0/0x48 returned 0 after 1148 usecs
[ 2.600130] calling tlan_probe+0x0/0xbf @ 1
[ 2.600130] tlan: ThunderLAN driver v1.17
[ 2.600130] tlan: 0 devices installed, PCI: 0 EISA: 0
[ 2.600130] initcall tlan_probe+0x0/0xbf returned -19 after 1676 usecs
[ 2.600130] calling epic_init+0x0/0x11 @ 1
[ 2.600130] initcall epic_init+0x0/0x11 returned 0 after 776 usecs
[ 2.600130] calling sis190_init_module+0x0/0x11 @ 1
[ 2.610150] initcall sis190_init_module+0x0/0x11 returned 0 after 1296 usecs
[ 2.610150] calling sis900_init_module+0x0/0x11 @ 1
[ 2.610150] initcall sis900_init_module+0x0/0x11 returned 0 after 784 usecs
[ 2.610150] calling r6040_init+0x0/0x11 @ 1
[ 2.610150] initcall r6040_init+0x0/0x11 returned 0 after 704 usecs
[ 2.610150] calling yellowfin_init+0x0/0x11 @ 1
[ 2.610150] initcall yellowfin_init+0x0/0x11 returned 0 after 793 usecs
[ 2.610150] calling acenic_init+0x0/0x11 @ 1
[ 2.610150] initcall acenic_init+0x0/0x11 returned 0 after 705 usecs
[ 2.610150] calling natsemi_init_mod+0x0/0x11 @ 1
[ 2.610150] initcall natsemi_init_mod+0x0/0x11 returned 0 after 728 usecs
[ 2.610150] calling ns83820_init+0x0/0x1c @ 1
[ 2.610150] ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
[ 2.610150] initcall ns83820_init+0x0/0x1c returned 0 after 976 usecs
[ 2.610150] calling fealnx_init+0x0/0x11 @ 1
[ 2.619693] initcall fealnx_init+0x0/0x11 returned 0 after 1180 usecs
[ 2.619942] calling tg3_init+0x0/0x11 @ 1
[ 2.620126] initcall tg3_init+0x0/0x11 returned 0 after 784 usecs
[ 2.620126] calling bnx2_init+0x0/0x11 @ 1
[ 2.620126] initcall bnx2_init+0x0/0x11 returned 0 after 716 usecs
[ 2.620126] calling cnic_init+0x0/0x64 @ 1
[ 2.620126] cnic: Broadcom NetXtreme II CNIC Driver cnic v2.2.14 (Mar 30, 2011)
[ 2.620126] initcall cnic_init+0x0/0x64 returned 0 after 588 usecs
[ 2.620126] calling bnx2x_init+0x0/0x75 @ 1
[ 2.620126] Broadcom NetXtreme II 5771x 10Gigabit Ethernet Driver bnx2x 1.62.12-0 (2011/03/20)
[ 2.620126] initcall bnx2x_init+0x0/0x75 returned 0 after 1189 usecs
[ 2.620126] calling skge_init_module+0x0/0x29 @ 1
[ 2.620126] initcall skge_init_module+0x0/0x29 returned 0 after 729 usecs
[ 2.620126] calling sky2_init_module+0x0/0x1c @ 1
[ 2.620126] sky2: driver version 1.28
[ 2.620126] initcall sky2_init_module+0x0/0x1c returned 0 after 903 usecs
[ 2.620126] calling skfd_init+0x0/0x11 @ 1
[ 2.620126] initcall skfd_init+0x0/0x11 returned 0 after 811 usecs
[ 2.620126] calling ks8842_init+0x0/0xa @ 1
[ 2.630287] initcall ks8842_init+0x0/0xa returned 0 after 886 usecs
[ 2.630462] calling ks8851_init+0x0/0xa @ 1
[ 2.630462] initcall ks8851_init+0x0/0xa returned 0 after 482 usecs
[ 2.630462] calling ksz884x_init_module+0x0/0x11 @ 1
[ 2.630462] initcall ksz884x_init_module+0x0/0x11 returned 0 after 854 usecs
[ 2.630462] calling rhine_init+0x0/0x44 @ 1
[ 2.630462] initcall rhine_init+0x0/0x44 returned 0 after 803 usecs
[ 2.630462] calling velocity_init_module+0x0/0x30 @ 1
[ 2.630462] initcall velocity_init_module+0x0/0x30 returned 0 after 777 usecs
[ 2.630462] calling starfire_init+0x0/0x11 @ 1
[ 2.630462] initcall starfire_init+0x0/0x11 returned 0 after 711 usecs
[ 2.630462] calling stmmac_init_module+0x0/0x29 @ 1
[ 2.630462] initcall stmmac_init_module+0x0/0x29 returned 0 after 921 usecs
[ 2.630462] calling sundance_init+0x0/0x11 @ 1
[ 2.639553] initcall sundance_init+0x0/0x11 returned 0 after 1233 usecs
[ 2.639801] calling hamachi_init+0x0/0x11 @ 1
[ 2.640124] initcall hamachi_init+0x0/0x11 returned 0 after 846 usecs
[ 2.640124] calling net_olddevs_init+0x0/0x7e @ 1
[ 2.650149] cs89x0:cs89x0_probe(0x0)
[ 2.650149] PP_addr at 300[a]: 0xffff
[ 2.650149] eth1: incorrect signature at 300[c]: 0xffff!=0x630E
[ 2.650149] cs89x0: request_region(0x320, 0x10) failed
[ 2.650149] PP_addr at 340[a]: 0xffff
[ 2.650149] eth1: incorrect signature at 340[c]: 0xffff!=0x630E
[ 2.650149] PP_addr at 360[a]: 0xffff
[ 2.650149] eth1: incorrect signature at 360[c]: 0xffff!=0x630E
[ 2.650149] PP_addr at 200[a]: 0xffff
[ 2.650149] eth1: incorrect signature at 200[c]: 0xffff!=0x630E
[ 2.650149] PP_addr at 220[a]: 0xffff
[ 2.650149] eth1: incorrect signature at 220[c]: 0xffff!=0x630E
[ 2.650149] PP_addr at 240[a]: 0xffff
[ 2.650149] eth1: incorrect signature at 240[c]: 0xffff!=0x630E
[ 2.650149] PP_addr at 260[a]: 0xffff
[ 2.650149] eth1: incorrect signature at 260[c]: 0xffff!=0x630E
[ 2.650149] PP_addr at 280[a]: 0xffff
[ 2.650149] eth1: incorrect signature at 280[c]: 0xffff!=0x630E
[ 2.650149] PP_addr at 2a0[a]: 0xffff
[ 2.650149] eth1: incorrect signature at 2a0[c]: 0xffff!=0x630E
[ 2.650149] PP_addr at 2c0[a]: 0xffff
[ 2.650149] eth1: incorrect signature at 2c0[c]: 0xffff!=0x630E
[ 2.650149] PP_addr at 2e0[a]: 0xffff
[ 2.650149] eth1: incorrect signature at 2e0[c]: 0xffff!=0x630E
[ 2.650149] cs89x0: no cs8900 or cs8920 detected. Be sure to disable PnP with SETUP
[ 2.660133] D-Link DE-620 pocket adapter io 0x378, which is busy.
[ 2.660133] initcall net_olddevs_init+0x0/0x7e returned 0 after 20825 usecs
[ 2.660133] calling sb1000_init+0x0/0xa @ 1
[ 2.660133] initcall sb1000_init+0x0/0xa returned 0 after 572 usecs
[ 2.660133] calling hp100_module_init+0x0/0x11 @ 1
[ 2.660133] initcall hp100_module_init+0x0/0x11 returned 0 after 918 usecs
[ 2.660133] calling NS8390p_init_module+0x0/0x3 @ 1
[ 2.660133] initcall NS8390p_init_module+0x0/0x3 returned 0 after 1 usecs
[ 2.660133] calling ne_init+0x0/0x1d @ 1
[ 2.669571] initcall ne_init+0x0/0x1d returned -19 after 3478 usecs
[ 2.669820] calling b44_init+0x0/0x3b @ 1
[ 2.670198] initcall b44_init+0x0/0x3b returned 0 after 1306 usecs
[ 2.670198] calling init_nic+0x0/0x11 @ 1
[ 2.670198] initcall init_nic+0x0/0x11 returned 0 after 742 usecs
[ 2.670198] calling ql3xxx_init_module+0x0/0x11 @ 1
[ 2.670198] initcall ql3xxx_init_module+0x0/0x11 returned 0 after 733 usecs
[ 2.670198] calling qlcnic_init_module+0x0/0x93 @ 1
[ 2.670198] QLogic 1/10 GbE Converged/Intelligent Ethernet Driver v5.0.18
[ 2.670198] initcall qlcnic_init_module+0x0/0x93 returned 0 after 1186 usecs
[ 2.670198] calling qlge_init_module+0x0/0x11 @ 1
[ 2.670198] initcall qlge_init_module+0x0/0x11 returned 0 after 746 usecs
[ 2.670198] calling ppp_init+0x0/0xbf @ 1
[ 2.670198] PPP generic driver version 2.4.2
[ 2.670198] initcall ppp_init+0x0/0xbf returned 0 after 1294 usecs
[ 2.670198] calling ppp_async_init+0x0/0x27 @ 1
[ 2.670198] initcall ppp_async_init+0x0/0x27 returned 0 after 5 usecs
[ 2.670198] calling ppp_sync_init+0x0/0x27 @ 1
[ 2.670198] initcall ppp_sync_init+0x0/0x27 returned 0 after 1 usecs
[ 2.670198] calling deflate_init+0x0/0x2a @ 1
[ 2.670198] PPP Deflate Compression module registered
[ 2.670198] initcall deflate_init+0x0/0x2a returned 0 after 195 usecs
[ 2.670198] calling ppp_mppe_init+0x0/0xa8 @ 1
[ 2.700146] PPP MPPE Compression module registered
[ 2.700146] initcall ppp_mppe_init+0x0/0xa8 returned 0 after 21550 usecs
[ 2.700146] calling pppox_init+0x0/0xa @ 1
[ 2.700146] NET: Registered protocol family 24
[ 2.700146] initcall pppox_init+0x0/0xa returned 0 after 190 usecs
[ 2.700146] calling pppoe_init+0x0/0x6d @ 1
[ 2.700146] initcall pppoe_init+0x0/0x6d returned 0 after 72 usecs
[ 2.700146] calling netif_init+0x0/0x55 @ 1
[ 2.700146] initcall netif_init+0x0/0x55 returned 0 after 1 usecs
[ 2.700146] calling netback_init+0x0/0x1c9 @ 1
[ 2.700146] initcall netback_init+0x0/0x1c9 returned 0 after 1328 usecs
[ 2.700146] calling dummy_init_module+0x0/0x83 @ 1
[ 2.700146] initcall dummy_init_module+0x0/0x83 returned 0 after 1951 usecs
[ 2.700146] calling ifb_init_module+0x0/0x81 @ 1
[ 2.710162] initcall ifb_init_module+0x0/0x81 returned 0 after 4172 usecs
[ 2.710162] calling macvlan_init_module+0x0/0x2d @ 1
[ 2.710162] initcall macvlan_init_module+0x0/0x2d returned 0 after 6 usecs
[ 2.710162] calling de600_init+0x0/0x2a8 @ 1
[ 2.710162] DE600: port 0x378 busy
[ 2.710162] initcall de600_init+0x0/0x2a8 returned -16 after 276 usecs
[ 2.710162] initcall de600_init+0x0/0x2a8 returned with error code -16
[ 2.710162] calling dfx_init+0x0/0x11 @ 1
[ 2.710162] initcall dfx_init+0x0/0x11 returned 0 after 819 usecs
[ 2.710162] calling el3_init_module+0x0/0x105 @ 1
[ 2.760109] initcall el3_init_module+0x0/0x105 returned 0 after 49339 usecs
[ 2.760109] calling cp_init+0x0/0x11 @ 1
[ 2.760109] initcall cp_init+0x0/0x11 returned 0 after 788 usecs
[ 2.760109] calling rtl8139_init_module+0x0/0x11 @ 1
[ 2.769468] initcall rtl8139_init_module+0x0/0x11 returned 0 after 1054 usecs
[ 2.769717] calling znet_probe+0x0/0x22a @ 1
[ 2.770175] initcall znet_probe+0x0/0x22a returned -19 after 790 usecs
[ 2.770175] calling depca_module_init+0x0/0xb8 @ 1
[ 2.770175] initcall depca_module_init+0x0/0xb8 returned 0 after 2698 usecs
[ 2.770175] calling atp_init_module+0x0/0x82 @ 1
[ 2.770175] atp.c:v1.09=ac 2002/10/01 Donald Becker <becker@scyld.com>
[ 2.770175] initcall atp_init_module+0x0/0x82 returned -19 after 295 usecs
[ 2.770175] calling sc92031_init+0x0/0x11 @ 1
[ 2.770175] initcall sc92031_init+0x0/0x11 returned 0 after 894 usecs
[ 2.770175] calling lp486e_init_module+0x0/0x217 @ 1
[ 2.770175] eth%d: i82596 initialization timed out
[ 2.770175] initcall lp486e_init_module+0x0/0x217 returned -19 after 931 usecs
[ 2.770175] calling eql_init_module+0x0/0x52 @ 1
[ 2.770175] eql: Equalizer2002: Simon Janes (simon@ncm.com) and David S. Miller (davem@redhat.com)
[ 2.780139] initcall eql_init_module+0x0/0x52 returned 0 after 2524 usecs
[ 2.780139] calling tun_init+0x0/0x73 @ 1
[ 2.780139] tun: Universal TUN/TAP device driver, 1.6
[ 2.780139] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 2.780139] initcall tun_init+0x0/0x73 returned 0 after 1050 usecs
[ 2.780139] calling veth_init+0x0/0xa @ 1
[ 2.780139] initcall veth_init+0x0/0xa returned 0 after 3 usecs
[ 2.780139] calling rio_init+0x0/0x11 @ 1
[ 2.780139] initcall rio_init+0x0/0x11 returned 0 after 903 usecs
[ 2.780139] calling rtl8169_init_module+0x0/0x11 @ 1
[ 2.780139] initcall rtl8169_init_module+0x0/0x11 returned 0 after 748 usecs
[ 2.780139] calling amd8111e_init+0x0/0x11 @ 1
[ 2.789923] initcall amd8111e_init+0x0/0x11 returned 0 after 1274 usecs
[ 2.790159] calling s2io_starter+0x0/0x11 @ 1
[ 2.790159] initcall s2io_starter+0x0/0x11 returned 0 after 792 usecs
[ 2.790159] calling vxge_starter+0x0/0x13b @ 1
[ 2.790159] vxge: Copyright(c) 2002-2010 Exar Corp.
[ 2.790159] vxge: Driver version: 2.5.3.22640-k
[ 2.790159] initcall vxge_starter+0x0/0x13b returned 0 after 1197 usecs
[ 2.790159] calling myri10ge_init_module+0x0/0x60 @ 1
[ 2.790159] myri10ge: Version 1.5.2-1.459
[ 2.790159] initcall myri10ge_init_module+0x0/0x60 returned 0 after 974 usecs
[ 2.790159] calling mlx4_init+0x0/0x8f @ 1
[ 2.790159] initcall mlx4_init+0x0/0x8f returned 0 after 983 usecs
[ 2.790159] calling mlx4_en_init+0x0/0xa @ 1
[ 2.790159] initcall mlx4_en_init+0x0/0xa returned 0 after 2 usecs
[ 2.790159] calling ethoc_init+0x0/0xa @ 1
[ 2.790159] initcall ethoc_init+0x0/0xa returned 0 after 496 usecs
[ 2.790159] calling dnet_init+0x0/0xa @ 1
[ 2.790159] initcall dnet_init+0x0/0xa returned 0 after 483 usecs
[ 2.790159] calling olympic_pci_init+0x0/0x11 @ 1
[ 2.799983] initcall olympic_pci_init+0x0/0x11 returned 0 after 1270 usecs
[ 2.800140] calling streamer_init_module+0x0/0x11 @ 1
[ 2.800140] initcall streamer_init_module+0x0/0x11 returned 0 after 758 usecs
[ 2.800140] calling abyss_init+0x0/0x3a @ 1
[ 2.800140] initcall abyss_init+0x0/0x3a returned 0 after 810 usecs
[ 2.800140] calling proteon_init+0x0/0x3e1 @ 1
[ 2.800140] proteon.c: 0 cards found.
[ 2.800140] proteon.c: No cards found.
[ 2.809243] initcall proteon_init+0x0/0x3e1 returned -19 after 6111 usecs
[ 2.809488] calling tms_pci_init+0x0/0x11 @ 1
[ 2.810158] initcall tms_pci_init+0x0/0x11 returned 0 after 1247 usecs
[ 2.810158] calling sk_isa_init+0x0/0x3e1 @ 1
[ 2.810158] skisa.c: 0 cards found.
[ 2.810158] skisa.c: No cards found.
[ 2.810158] initcall sk_isa_init+0x0/0x3e1 returned -19 after 5645 usecs
[ 2.810158] calling xl_pci_init+0x0/0x11 @ 1
[ 2.810158] initcall xl_pci_init+0x0/0x11 returned 0 after 909 usecs
[ 2.810158] calling init_tc589+0x0/0xa @ 1
[ 2.820202] initcall init_tc589+0x0/0xa returned 0 after 1024 usecs
[ 2.820306] calling init_tc574+0x0/0xa @ 1
[ 2.820306] initcall init_tc574+0x0/0xa returned 0 after 488 usecs
[ 2.820306] calling init_fmvj18x_cs+0x0/0xa @ 1
[ 2.820306] initcall init_fmvj18x_cs+0x0/0xa returned 0 after 519 usecs
[ 2.820306] calling init_nmclan_cs+0x0/0xa @ 1
[ 2.820306] initcall init_nmclan_cs+0x0/0xa returned 0 after 480 usecs
[ 2.820306] calling init_pcnet_cs+0x0/0xa @ 1
[ 2.820306] initcall init_pcnet_cs+0x0/0xa returned 0 after 760 usecs
[ 2.820306] calling init_smc91c92_cs+0x0/0xa @ 1
[ 2.820306] initcall init_smc91c92_cs+0x0/0xa returned 0 after 522 usecs
[ 2.820306] calling init_xirc2ps_cs+0x0/0xa @ 1
[ 2.820306] initcall init_xirc2ps_cs+0x0/0xa returned 0 after 537 usecs
[ 2.820306] calling init_axnet_cs+0x0/0xa @ 1
[ 2.820306] initcall init_axnet_cs+0x0/0xa returned 0 after 551 usecs
[ 2.820306] calling init_ibmtr_cs+0x0/0xa @ 1
[ 2.820306] initcall init_ibmtr_cs+0x0/0xa returned 0 after 476 usecs
[ 2.820306] calling catc_init+0x0/0x27 @ 1
[ 2.829952] usbcore: registered new interface driver catc
[ 2.830153] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
[ 2.830153] initcall catc_init+0x0/0x27 returned 0 after 1562 usecs
[ 2.830153] calling kaweth_init+0x0/0x11 @ 1
[ 2.830153] usbcore: registered new interface driver kaweth
[ 2.830153] initcall kaweth_init+0x0/0x11 returned 0 after 889 usecs
[ 2.830153] calling pegasus_init+0x0/0x118 @ 1
[ 2.830153] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[ 2.830153] usbcore: registered new interface driver pegasus
[ 2.830153] initcall pegasus_init+0x0/0x118 returned 0 after 1149 usecs
[ 2.830153] calling usb_rtl8150_init+0x0/0x1c @ 1
[ 2.830153] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver
[ 2.830153] usbcore: registered new interface driver rtl8150
[ 2.830153] initcall usb_rtl8150_init+0x0/0x1c returned 0 after 1033 usecs
[ 2.830153] calling asix_init+0x0/0x11 @ 1
[ 2.830153] usbcore: registered new interface driver asix
[ 2.830153] initcall asix_init+0x0/0x11 returned 0 after 842 usecs
[ 2.830153] calling cdc_init+0x0/0x11 @ 1
[ 2.830153] usbcore: registered new interface driver cdc_ether
[ 2.830153] initcall cdc_init+0x0/0x11 returned 0 after 831 usecs
[ 2.830153] calling eem_init+0x0/0x11 @ 1
[ 2.830153] usbcore: registered new interface driver cdc_eem
[ 2.830153] initcall eem_init+0x0/0x11 returned 0 after 840 usecs
[ 2.830153] calling dm9601_init+0x0/0x11 @ 1
[ 2.840292] usbcore: registered new interface driver dm9601
[ 2.840441] initcall dm9601_init+0x0/0x11 returned 0 after 1346 usecs
[ 2.840441] calling smsc95xx_init+0x0/0x11 @ 1
[ 2.840441] usbcore: registered new interface driver smsc95xx
[ 2.840441] initcall smsc95xx_init+0x0/0x11 returned 0 after 866 usecs
[ 2.840441] calling usbnet_init+0x0/0x11 @ 1
[ 2.840441] usbcore: registered new interface driver gl620a
[ 2.840441] initcall usbnet_init+0x0/0x11 returned 0 after 814 usecs
[ 2.840441] calling net1080_init+0x0/0x11 @ 1
[ 2.840441] usbcore: registered new interface driver net1080
[ 2.840441] initcall net1080_init+0x0/0x11 returned 0 after 769 usecs
[ 2.840441] calling plusb_init+0x0/0x11 @ 1
[ 2.840441] usbcore: registered new interface driver plusb
[ 2.840441] initcall plusb_init+0x0/0x11 returned 0 after 904 usecs
[ 2.840441] calling rndis_init+0x0/0x11 @ 1
[ 2.840441] usbcore: registered new interface driver rndis_host
[ 2.840441] initcall rndis_init+0x0/0x11 returned 0 after 865 usecs
[ 2.840441] calling cdc_subset_init+0x0/0x11 @ 1
[ 2.840441] usbcore: registered new interface driver cdc_subset
[ 2.840441] initcall cdc_subset_init+0x0/0x11 returned 0 after 848 usecs
[ 2.840441] calling zaurus_init+0x0/0x11 @ 1
[ 2.849849] usbcore: registered new interface driver zaurus
[ 2.850118] initcall zaurus_init+0x0/0x11 returned 0 after 1342 usecs
[ 2.850149] calling mcs7830_init+0x0/0x11 @ 1
[ 2.850149] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ 2.850149] initcall mcs7830_init+0x0/0x11 returned 0 after 1005 usecs
[ 2.850149] calling usbnet_init+0x0/0x22 @ 1
[ 2.850149] initcall usbnet_init+0x0/0x22 returned 0 after 26 usecs
[ 2.850149] calling int51x1_init+0x0/0x11 @ 1
[ 2.850149] usbcore: registered new interface driver int51x1
[ 2.850149] initcall int51x1_init+0x0/0x11 returned 0 after 862 usecs
[ 2.850149] calling cdc_ncm_init+0x0/0x1c @ 1
[ 2.850149] cdc_ncm: 01-June-2011
[ 2.850149] usbcore: registered new interface driver cdc_ncm
[ 2.850149] initcall cdc_ncm_init+0x0/0x1c returned 0 after 1036 usecs
[ 2.850149] calling xircom_init+0x0/0x11 @ 1
[ 2.850149] initcall xircom_init+0x0/0x11 returned 0 after 852 usecs
[ 2.850149] calling dmfe_init_module+0x0/0xdb @ 1
[ 2.850149] dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
[ 2.850149] initcall dmfe_init_module+0x0/0xdb returned 0 after 888 usecs
[ 2.850149] calling w840_init+0x0/0x1c @ 1
[ 2.850149] v1.01-e (2.4 port) Sep-11-2006 Donald Becker <becker@scyld.com>
[ 2.850149] http://www.scyld.com/network/drivers.html
[ 2.859519] initcall w840_init+0x0/0x1c returned 0 after 1499 usecs
[ 2.859771] calling de_init+0x0/0x11 @ 1
[ 2.860123] initcall de_init+0x0/0x11 returned 0 after 809 usecs
[ 2.860123] calling tulip_init+0x0/0x25 @ 1
[ 2.860123] Linux Tulip driver version 1.1.15 (Feb 27, 2007)
[ 2.860123] xen: registering gsi 5 triggering 0 polarity 1
[ 2.860123] xen_map_pirq_gsi: returning irq 5 for gsi 5
[ 2.860123] xen: --> pirq=5 -> irq=5
[ 2.860123] Failed to setup GSI :5, err_code:-22
[ 2.860123] tulip 0000:01:09.0: PCI INT A -> Link[LNKC] -> GSI 5 (level, low) -> IRQ 5
[ 2.860123] tulip: tulip_init_one: Enabled WOL support for AN983B
[ 2.860123] tulip0: MII transceiver #1 config 1000 status 7849 advertising 05e1
[ 2.870146] net eth1: ADMtek Comet rev 49 at MMIO 0xfdfffc00, 00:04:75:b5:41:a9, IRQ 5
[ 2.870146] initcall tulip_init+0x0/0x25 returned 0 after 10090 usecs
[ 2.870146] calling de4x5_module_init+0x0/0x11 @ 1
[ 2.870146] initcall de4x5_module_init+0x0/0x11 returned 0 after 795 usecs
[ 2.870146] calling uli526x_init_module+0x0/0x8e @ 1
[ 2.870146] uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29)
[ 2.870146] initcall uli526x_init_module+0x0/0x8e returned 0 after 1009 usecs
[ 2.870146] calling init_netconsole+0x0/0x19d @ 1
[ 2.870146] console [netcon0] enabled
[ 2.870146] netconsole: network logging started
[ 2.870146] initcall init_netconsole+0x0/0x19d returned 0 after 448 usecs
[ 2.870146] calling netxen_init_module+0x0/0x36 @ 1
[ 2.870146] QLogic/NetXen Network Driver v4.0.75
[ 2.870146] initcall netxen_init_module+0x0/0x36 returned 0 after 995 usecs
[ 2.870146] calling niu_init+0x0/0x31 @ 1
[ 2.870146] initcall niu_init+0x0/0x31 returned 0 after 798 usecs
[ 2.870146] calling init+0x0/0xa @ 1
[ 2.870146] initcall init+0x0/0xa returned 0 after 450 usecs
[ 2.870146] calling efx_init_module+0x0/0x77 @ 1
[ 2.870146] Solarflare NET driver v3.1
[ 2.880790] initcall efx_init_module+0x0/0x77 returned 0 after 1568 usecs
[ 2.880790] calling pch_gbe_init_module+0x0/0x42 @ 1
[ 2.880790] initcall pch_gbe_init_module+0x0/0x42 returned 0 after 797 usecs
[ 2.880790] calling i2o_iop_init+0x0/0x41 @ 1
[ 2.880790] I2O subsystem v1.325
[ 2.880790] i2o: max drivers = 8
[ 2.880790] initcall i2o_iop_init+0x0/0x41 returned 0 after 2314 usecs
[ 2.880790] calling i2o_config_init+0x0/0x7d @ 1
[ 2.880790] I2O Configuration OSM v1.323
[ 2.880790] initcall i2o_config_init+0x0/0x7d returned 0 after 1147 usecs
[ 2.880790] calling i2o_bus_init+0x0/0x31 @ 1
[ 2.880790] I2O Bus Adapter OSM v1.317
[ 2.880790] initcall i2o_bus_init+0x0/0x31 returned 0 after 643 usecs
[ 2.880790] calling i2o_block_init+0x0/0xf1 @ 1
[ 2.880790] I2O Block Device OSM v1.325
[ 2.890162] initcall i2o_block_init+0x0/0xf1 returned 0 after 2489 usecs
[ 2.890162] calling i2o_scsi_init+0x0/0x31 @ 1
[ 2.890162] I2O SCSI Peripheral OSM v1.316
[ 2.890162] initcall i2o_scsi_init+0x0/0x31 returned 0 after 662 usecs
[ 2.890162] calling i2o_proc_init+0x0/0x133 @ 1
[ 2.890162] I2O ProcFS OSM v1.316
[ 2.890162] initcall i2o_proc_init+0x0/0x133 returned 0 after 696 usecs
[ 2.890162] calling fusion_init+0x0/0xce @ 1
[ 2.890162] Fusion MPT base driver 3.04.19
[ 2.890162] Copyright (c) 1999-2008 LSI Corporation
[ 2.890162] initcall fusion_init+0x0/0xce returned 0 after 409 usecs
[ 2.890162] calling mptspi_init+0x0/0xc6 @ 1
[ 2.890162] Fusion MPT SPI Host driver 3.04.19
[ 2.890162] initcall mptspi_init+0x0/0xc6 returned 0 after 1039 usecs
[ 2.890162] calling mptfc_init+0x0/0xd9 @ 1
[ 2.890162] Fusion MPT FC Host driver 3.04.19
[ 2.900785] initcall mptfc_init+0x0/0xd9 returned 0 after 1358 usecs
[ 2.901019] calling mptsas_init+0x0/0x102 @ 1
[ 2.901034] Fusion MPT SAS Host driver 3.04.19
[ 2.901034] initcall mptsas_init+0x0/0x102 returned 0 after 1067 usecs
[ 2.901034] calling mptctl_init+0x0/0x116 @ 1
[ 2.901034] Fusion MPT misc device (ioctl) driver 3.04.19
[ 2.901034] mptctl: Registered with Fusion MPT base driver
[ 2.901034] mptctl: /dev/mptctl @ (major,minor=10,220)
[ 2.901034] initcall mptctl_init+0x0/0x116 returned 0 after 1255 usecs
[ 2.901034] calling mpt_lan_init+0x0/0x6f @ 1
[ 2.901034] Fusion MPT LAN driver 3.04.19
[ 2.901034] initcall mpt_lan_init+0x0/0x6f returned 0 after 193 usecs
[ 2.901034] calling fw_core_init+0x0/0xbd @ 1
[ 2.901034] initcall fw_core_init+0x0/0xbd returned 0 after 790 usecs
[ 2.901034] calling fw_ohci_init+0x0/0x11 @ 1
[ 2.901034] initcall fw_ohci_init+0x0/0x11 returned 0 after 920 usecs
[ 2.901034] calling sbp2_init+0x0/0xa @ 1
[ 2.901034] initcall sbp2_init+0x0/0xa returned 0 after 432 usecs
[ 2.901034] calling fwnet_init+0x0/0x5e @ 1
[ 2.910156] initcall fwnet_init+0x0/0x5e returned 0 after 1919 usecs
[ 2.910156] calling uio_init+0x0/0xc5 @ 1
[ 2.910156] initcall uio_init+0x0/0xc5 returned 0 after 513 usecs
[ 2.910156] calling cdrom_init+0x0/0x8 @ 1
[ 2.910156] initcall cdrom_init+0x0/0x8 returned 0 after 1 usecs
[ 2.910156] calling ks0108_init+0x0/0x95 @ 1
[ 2.910156] initcall ks0108_init+0x0/0x95 returned 0 after 58 usecs
[ 2.910156] calling nonstatic_sysfs_init+0x0/0xa @ 1
[ 2.910156] initcall nonstatic_sysfs_init+0x0/0xa returned 0 after 6 usecs
[ 2.910156] calling yenta_socket_init+0x0/0x11 @ 1
[ 2.910156] initcall yenta_socket_init+0x0/0x11 returned 0 after 890 usecs
[ 2.910156] calling pd6729_module_init+0x0/0x11 @ 1
[ 2.910156] initcall pd6729_module_init+0x0/0x11 returned 0 after 760 usecs
[ 2.910156] calling init_i82365+0x0/0x517 @ 1
[ 2.910156] Intel ISA PCIC probe: not found.
[ 2.910156] initcall init_i82365+0x0/0x517 returned -19 after 2352 usecs
[ 2.910156] calling i82092aa_module_init+0x0/0x11 @ 1
[ 2.920459] initcall i82092aa_module_init+0x0/0x11 returned 0 after 1299 usecs
[ 2.920651] calling aoe_init+0x0/0x96 @ 1
[ 2.920651] aoe: AoE v47 initialised.
[ 2.920651] initcall aoe_init+0x0/0x96 returned 0 after 3764 usecs
[ 2.920651] calling mon_init+0x0/0xd6 @ 1
[ 2.920651] usbmon: debugfs is not available
[ 2.920651] initcall mon_init+0x0/0xd6 returned -19 after 189 usecs
[ 2.920651] calling ehci_hcd_init+0x0/0x64 @ 1
[ 2.920651] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.920651] initcall ehci_hcd_init+0x0/0x64 returned 0 after 1151 usecs
[ 2.920651] calling oxu_module_init+0x0/0xa @ 1
[ 2.920651] initcall oxu_module_init+0x0/0xa returned 0 after 476 usecs
[ 2.920651] calling isp116x_init+0x0/0x30 @ 1
[ 2.920651] 116x: driver isp116x-hcd, 03 Nov 2005
[ 2.929711] initcall isp116x_init+0x0/0x30 returned 0 after 1106 usecs
[ 2.929951] calling isp1362_init+0x0/0x30 @ 1
[ 2.930146] driver isp1362-hcd, 2005-04-04
[ 2.930146] initcall isp1362_init+0x0/0x30 returned 0 after 706 usecs
[ 2.930146] calling ohci_hcd_mod_init+0x0/0x47 @ 1
[ 2.930146] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.930146] initcall ohci_hcd_mod_init+0x0/0x47 returned 0 after 1127 usecs
[ 2.930146] calling uhci_hcd_init+0x0/0x98 @ 1
[ 2.930146] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.930146] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[ 2.930146] xen: registering gsi 11 triggering 0 polarity 1
[ 2.930146] xen_map_pirq_gsi: returning irq 11 for gsi 11
[ 2.930146] xen: --> pirq=11 -> irq=11
[ 2.935693] Failed to setup GSI :11, err_code:-22
[ 2.935911] uhci_hcd 0000:00:1f.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 2.936640] uhci_hcd 0000:00:1f.2: setting latency timer to 64
[ 2.936640] uhci_hcd 0000:00:1f.2: UHCI Host Controller
[ 2.936640] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
[ 2.936640] uhci_hcd 0000:00:1f.2: irq 11, io base 0x0000ff80
[ 2.936640] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.936640] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.936640] usb usb1: Product: UHCI Host Controller
[ 2.936640] usb usb1: Manufacturer: Linux 3.0.0-rc3 uhci_hcd
[ 2.936640] usb usb1: SerialNumber: 0000:00:1f.2
[ 2.940949] hub 1-0:1.0: USB hub found
[ 2.940949] hub 1-0:1.0: 2 ports detected
[ 2.940949] initcall uhci_hcd_init+0x0/0x98 returned 0 after 9523 usecs
[ 2.940949] calling xhci_hcd_init+0x0/0x1f @ 1
[ 2.940949] initcall xhci_hcd_init+0x0/0x1f returned 0 after 782 usecs
[ 2.940949] calling sl811h_init+0x0/0x30 @ 1
[ 2.940949] sl811: driver sl811-hcd, 19 May 2005
[ 2.940949] initcall sl811h_init+0x0/0x30 returned 0 after 684 usecs
[ 2.940949] calling r8a66597_init+0x0/0x30 @ 1
[ 2.940949] r8a66597_hcd: driver r8a66597_hcd, 2009-05-26
[ 2.940949] initcall r8a66597_init+0x0/0x30 returned 0 after 672 usecs
[ 2.940949] calling isp1760_init+0x0/0x40 @ 1
[ 2.940949] initcall isp1760_init+0x0/0x40 returned 0 after 1644 usecs
[ 2.940949] calling uas_init+0x0/0x11 @ 1
[ 2.949972] usbcore: registered new interface driver uas
[ 2.950151] initcall uas_init+0x0/0x11 returned 0 after 1195 usecs
[ 2.950151] calling usb_stor_init+0x0/0x32 @ 1
[ 2.950151] Initializing USB Mass Storage driver...
[ 2.950151] usbcore: registered new interface driver usb-storage
[ 2.950151] USB Mass Storage support registered.
[ 2.950151] initcall usb_stor_init+0x0/0x32 returned 0 after 1307 usecs
[ 2.950151] calling alauda_init+0x0/0x11 @ 1
[ 2.950151] usbcore: registered new interface driver ums-alauda
[ 2.950151] initcall alauda_init+0x0/0x11 returned 0 after 876 usecs
[ 2.950151] calling cypress_init+0x0/0x11 @ 1
[ 2.950151] usbcore: registered new interface driver ums-cypress
[ 2.950151] initcall cypress_init+0x0/0x11 returned 0 after 897 usecs
[ 2.950151] calling datafab_init+0x0/0x11 @ 1
[ 2.950151] usbcore: registered new interface driver ums-datafab
[ 2.950151] initcall datafab_init+0x0/0x11 returned 0 after 871 usecs
[ 2.950151] calling freecom_init+0x0/0x11 @ 1
[ 2.950151] usbcore: registered new interface driver ums-freecom
[ 2.950151] initcall freecom_init+0x0/0x11 returned 0 after 820 usecs
[ 2.950151] calling isd200_init+0x0/0x11 @ 1
[ 2.950151] usbcore: registered new interface driver ums-isd200
[ 2.950151] initcall isd200_init+0x0/0x11 returned 0 after 787 usecs
[ 2.950151] calling jumpshot_init+0x0/0x11 @ 1
[ 2.960135] usbcore: registered new interface driver ums-jumpshot
[ 2.960135] initcall jumpshot_init+0x0/0x11 returned 0 after 1452 usecs
[ 2.960135] calling karma_init+0x0/0x11 @ 1
[ 2.960135] usbcore: registered new interface driver ums-karma
[ 2.960135] initcall karma_init+0x0/0x11 returned 0 after 885 usecs
[ 2.960135] calling onetouch_init+0x0/0x11 @ 1
[ 2.960135] usbcore: registered new interface driver ums-onetouch
[ 2.960135] initcall onetouch_init+0x0/0x11 returned 0 after 883 usecs
[ 2.960135] calling realtek_cr_init+0x0/0x11 @ 1
[ 2.960135] usbcore: registered new interface driver ums-realtek
[ 2.960135] initcall realtek_cr_init+0x0/0x11 returned 0 after 827 usecs
[ 2.960135] calling sddr09_init+0x0/0x11 @ 1
[ 2.960135] usbcore: registered new interface driver ums-sddr09
[ 2.960135] initcall sddr09_init+0x0/0x11 returned 0 after 892 usecs
[ 2.960135] calling sddr55_init+0x0/0x11 @ 1
[ 2.960135] usbcore: registered new interface driver ums-sddr55
[ 2.960135] initcall sddr55_init+0x0/0x11 returned 0 after 868 usecs
[ 2.960135] calling usbat_init+0x0/0x11 @ 1
[ 2.960135] usbcore: registered new interface driver ums-usbat
[ 2.960135] initcall usbat_init+0x0/0x11 returned 0 after 884 usecs
[ 2.960135] calling usb_sisusb_init+0x0/0x16 @ 1
[ 2.970064] usbcore: registered new interface driver sisusb
[ 2.970170] initcall usb_sisusb_init+0x0/0x16 returned 0 after 1403 usecs
[ 2.970170] calling i8042_init+0x0/0x345 @ 1
[ 2.970170] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[ 2.970170] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.970170] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.970170] initcall i8042_init+0x0/0x345 returned 0 after 5526 usecs
[ 2.970170] calling serport_init+0x0/0x25 @ 1
[ 2.970170] initcall serport_init+0x0/0x25 returned 0 after 3 usecs
[ 2.970170] calling serio_raw_init+0x0/0x11 @ 1
[ 2.970170] initcall serio_raw_init+0x0/0x11 returned 0 after 1203 usecs
[ 2.970170] calling mousedev_init+0x0/0x4b @ 1
[ 2.980134] mousedev: PS/2 mouse device common for all mice
[ 2.980134] initcall mousedev_init+0x0/0x4b returned 0 after 1629 usecs
[ 2.980134] calling evdev_init+0x0/0xa @ 1
[ 2.980134] initcall evdev_init+0x0/0xa returned 0 after 614 usecs
[ 2.980134] calling atkbd_init+0x0/0x1b @ 1
[ 2.980134] initcall atkbd_init+0x0/0x1b returned 0 after 716 usecs
[ 2.980134] calling atp_init+0x0/0x11 @ 1
[ 2.980134] usbcore: registered new interface driver appletouch
[ 2.980134] initcall atp_init+0x0/0x11 returned 0 after 1030 usecs
[ 2.980134] calling bcm5974_init+0x0/0x11 @ 1
[ 2.980134] usbcore: registered new interface driver bcm5974
[ 2.980134] initcall bcm5974_init+0x0/0x11 returned 0 after 890 usecs
[ 2.980134] calling psmouse_init+0x0/0x65 @ 1
[ 2.980134] initcall psmouse_init+0x0/0x65 returned 0 after 984 usecs
[ 2.980134] calling sermouse_init+0x0/0x11 @ 1
[ 2.980134] initcall sermouse_init+0x0/0x11 returned 0 after 640 usecs
[ 2.980134] calling synaptics_i2c_init+0x0/0xc @ 1
[ 2.989907] initcall synaptics_i2c_init+0x0/0xc returned 0 after 935 usecs
[ 2.990157] calling vsxxxaa_init+0x0/0x11 @ 1
[ 2.990167] initcall vsxxxaa_init+0x0/0x11 returned 0 after 687 usecs
[ 2.990167] calling pcspkr_init+0x0/0xa @ 1
[ 2.990167] input: PC Speaker as /devices/platform/pcspkr/input/input1
[ 2.990167] initcall pcspkr_init+0x0/0xa returned 0 after 2047 usecs
[ 2.990167] calling bq32k_init+0x0/0xc @ 1
[ 2.990167] initcall bq32k_init+0x0/0xc returned 0 after 449 usecs
[ 2.990167] calling bq4802_init+0x0/0xa @ 1
[ 2.990167] initcall bq4802_init+0x0/0xa returned 0 after 597 usecs
[ 2.990167] calling cmos_init+0x0/0x5a @ 1
[ 3.000368] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 3.000368] rtc0: alarms up to one day, 242 bytes nvram
[ 3.000368] initcall cmos_init+0x0/0x5a returned 0 after 2695 usecs
[ 3.000368] calling ds1286_init+0x0/0xa @ 1
[ 3.000368] initcall ds1286_init+0x0/0xa returned 0 after 509 usecs
[ 3.000368] calling ds1307_init+0x0/0xc @ 1
[ 3.000368] initcall ds1307_init+0x0/0xc returned 0 after 600 usecs
[ 3.000368] calling ds1374_init+0x0/0xc @ 1
[ 3.000368] initcall ds1374_init+0x0/0xc returned 0 after 450 usecs
[ 3.000368] calling ds1511_rtc_init+0x0/0xa @ 1
[ 3.000368] initcall ds1511_rtc_init+0x0/0xa returned 0 after 507 usecs
[ 3.000368] calling ds1553_init+0x0/0xa @ 1
[ 3.000368] initcall ds1553_init+0x0/0xa returned 0 after 620 usecs
[ 3.000368] calling ds1672_init+0x0/0xc @ 1
[ 3.000368] initcall ds1672_init+0x0/0xc returned 0 after 456 usecs
[ 3.000368] calling ds1742_init+0x0/0xa @ 1
[ 3.000368] initcall ds1742_init+0x0/0xa returned 0 after 487 usecs
[ 3.000368] calling ds3232_init+0x0/0xc @ 1
[ 3.010511] initcall ds3232_init+0x0/0xc returned 0 after 1062 usecs
[ 3.010572] calling em3027_init+0x0/0xc @ 1
[ 3.010572] initcall em3027_init+0x0/0xc returned 0 after 470 usecs
[ 3.010572] calling fm3130_init+0x0/0xc @ 1
[ 3.010572] initcall fm3130_init+0x0/0xc returned 0 after 440 usecs
[ 3.010572] calling isl1208_init+0x0/0xc @ 1
[ 3.010572] initcall isl1208_init+0x0/0xc returned 0 after 609 usecs
[ 3.010572] calling isl12022_init+0x0/0xc @ 1
[ 3.010572] initcall isl12022_init+0x0/0xc returned 0 after 413 usecs
[ 3.010572] calling m41t80_rtc_init+0x0/0xc @ 1
[ 3.010572] initcall m41t80_rtc_init+0x0/0xc returned 0 after 413 usecs
[ 3.010572] calling m48t35_init+0x0/0xa @ 1
[ 3.010572] initcall m48t35_init+0x0/0xa returned 0 after 1166 usecs
[ 3.010572] calling m48t59_rtc_init+0x0/0xa @ 1
[ 3.010572] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[ 3.010572] initcall m48t59_rtc_init+0x0/0xa returned 0 after 1590 usecs
[ 3.010572] calling m48t86_rtc_init+0x0/0xa @ 1
[ 3.020628] initcall m48t86_rtc_init+0x0/0xa returned 0 after 1439 usecs
[ 3.020628] calling max6900_init+0x0/0xc @ 1
[ 3.020628] initcall max6900_init+0x0/0xc returned 0 after 500 usecs
[ 3.020628] calling msm6242_rtc_init+0x0/0xf @ 1
[ 3.020628] initcall msm6242_rtc_init+0x0/0xf returned -19 after 904 usecs
[ 3.020628] calling pcf8563_init+0x0/0xc @ 1
[ 3.020628] initcall pcf8563_init+0x0/0xc returned 0 after 452 usecs
[ 3.020628] calling pcf8583_init+0x0/0xc @ 1
[ 3.020628] initcall pcf8583_init+0x0/0xc returned 0 after 454 usecs
[ 3.020628] calling rp5c01_rtc_init+0x0/0xf @ 1
[ 3.020628] initcall rp5c01_rtc_init+0x0/0xf returned -19 after 952 usecs
[ 3.020628] calling rs5c372_init+0x0/0xc @ 1
[ 3.020628] initcall rs5c372_init+0x0/0xc returned 0 after 477 usecs
[ 3.020628] calling rv3029c2_init+0x0/0xc @ 1
[ 3.020628] initcall rv3029c2_init+0x0/0xc returned 0 after 469 usecs
[ 3.020628] calling rx8025_init+0x0/0xc @ 1
[ 3.030026] initcall rx8025_init+0x0/0xc returned 0 after 1132 usecs
[ 3.030118] calling rx8581_init+0x0/0xc @ 1
[ 3.030118] initcall rx8581_init+0x0/0xc returned 0 after 492 usecs
[ 3.030118] calling s35390a_rtc_init+0x0/0xc @ 1
[ 3.030118] initcall s35390a_rtc_init+0x0/0xc returned 0 after 456 usecs
[ 3.030118] calling stk17ta8_init+0x0/0xa @ 1
[ 3.030118] initcall stk17ta8_init+0x0/0xa returned 0 after 498 usecs
[ 3.030118] calling v3020_init+0x0/0xa @ 1
[ 3.030118] initcall v3020_init+0x0/0xa returned 0 after 509 usecs
[ 3.030118] calling x1205_init+0x0/0xc @ 1
[ 3.030118] initcall x1205_init+0x0/0xc returned 0 after 463 usecs
[ 3.030118] calling i2c_smbus_init+0x0/0xc @ 1
[ 3.030118] initcall i2c_smbus_init+0x0/0xc returned 0 after 450 usecs
[ 3.030118] calling i2c_dev_init+0x0/0xa7 @ 1
[ 3.030118] i2c /dev entries driver
[ 3.030118] initcall i2c_dev_init+0x0/0xa7 returned 0 after 698 usecs
[ 3.030118] calling i2c_ali1535_init+0x0/0x11 @ 1
[ 3.040014] initcall i2c_ali1535_init+0x0/0x11 returned 0 after 2630 usecs
[ 3.040129] calling ali1563_init+0x0/0x11 @ 1
[ 3.040129] initcall ali1563_init+0x0/0x11 returned 0 after 934 usecs
[ 3.040129] calling i2c_ali15x3_init+0x0/0x11 @ 1
[ 3.040129] initcall i2c_ali15x3_init+0x0/0x11 returned 0 after 812 usecs
[ 3.040129] calling amd756_init+0x0/0x11 @ 1
[ 3.040129] initcall amd756_init+0x0/0x11 returned 0 after 777 usecs
[ 3.040129] calling i2c_amd8111_init+0x0/0x11 @ 1
[ 3.040129] initcall i2c_amd8111_init+0x0/0x11 returned 0 after 851 usecs
[ 3.040129] calling i2c_i801_init+0x0/0x8f @ 1
[ 3.040129] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
[ 3.040129] xen: registering gsi 10 triggering 0 polarity 1
[ 3.040129] xen_map_pirq_gsi: returning irq 10 for gsi 10
[ 3.040129] xen: --> pirq=10 -> irq=10
[ 3.040129] Failed to setup GSI :10, err_code:-22
[ 3.040129] i801_smbus 0000:00:1f.3: PCI INT B -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10
[ 3.040129] i801_smbus 0000:00:1f.3: Enabling SMBus device
[ 3.050144] initcall i2c_i801_init+0x0/0x8f returned 0 after 5572 usecs
[ 3.050144] calling i2c_sch_init+0x0/0xa @ 1
[ 3.050144] initcall i2c_sch_init+0x0/0xa returned 0 after 508 usecs
[ 3.050144] calling nforce2_init+0x0/0x11 @ 1
[ 3.050144] initcall nforce2_init+0x0/0x11 returned 0 after 931 usecs
[ 3.050144] calling i2c_piix4_init+0x0/0x11 @ 1
[ 3.050144] initcall i2c_piix4_init+0x0/0x11 returned 0 after 866 usecs
[ 3.050144] calling i2c_sis5595_init+0x0/0x11 @ 1
[ 3.050144] initcall i2c_sis5595_init+0x0/0x11 returned 0 after 896 usecs
[ 3.050144] calling i2c_sis630_init+0x0/0x11 @ 1
[ 3.050144] initcall i2c_sis630_init+0x0/0x11 returned 0 after 765 usecs
[ 3.050144] calling i2c_sis96x_init+0x0/0x11 @ 1
[ 3.059648] initcall i2c_sis96x_init+0x0/0x11 returned 0 after 1285 usecs
[ 3.059895] calling i2c_vt586b_init+0x0/0x11 @ 1
[ 3.060133] initcall i2c_vt586b_init+0x0/0x11 returned 0 after 913 usecs
[ 3.060133] calling i2c_vt596_init+0x0/0x11 @ 1
[ 3.060133] initcall i2c_vt596_init+0x0/0x11 returned 0 after 873 usecs
[ 3.060133] calling i2c_pca_pf_init+0x0/0xa @ 1
[ 3.060133] initcall i2c_pca_pf_init+0x0/0xa returned 0 after 501 usecs
[ 3.060133] calling i2c_adap_simtec_init+0x0/0xa @ 1
[ 3.060133] initcall i2c_adap_simtec_init+0x0/0xa returned 0 after 498 usecs
[ 3.060133] calling i2c_parport_init+0x0/0x3a @ 1
[ 3.060133] i2c-parport: adapter type unspecified
[ 3.060133] initcall i2c_parport_init+0x0/0x3a returned -19 after 189 usecs
[ 3.060133] calling i2c_parport_init+0x0/0x13f @ 1
[ 3.060133] i2c-parport-light: adapter type unspecified
[ 3.060133] initcall i2c_parport_init+0x0/0x13f returned -19 after 192 usecs
[ 3.060133] calling usb_i2c_tiny_usb_init+0x0/0x11 @ 1
[ 3.060133] usbcore: registered new interface driver i2c-tiny-usb
[ 3.060133] initcall usb_i2c_tiny_usb_init+0x0/0x11 returned 0 after 923 usecs
[ 3.060133] calling pca_isa_init+0x0/0xf @ 1
[ 3.060133] isa i2c-pca-isa.0: Please specify I/O base
[ 3.070161] initcall pca_isa_init+0x0/0xf returned -19 after 2608 usecs
[ 3.070161] calling bq27x00_battery_init+0x0/0x48 @ 1
[ 3.070161] initcall bq27x00_battery_init+0x0/0x48 returned 0 after 886 usecs
[ 3.070161] calling acpi_power_meter_init+0x0/0x2b @ 1
[ 3.070161] initcall acpi_power_meter_init+0x0/0x2b returned 0 after 489 usecs
[ 3.070161] calling atk0110_init+0x0/0x52 @ 1
[ 3.070161] initcall atk0110_init+0x0/0x52 returned 0 after 501 usecs
[ 3.070161] calling asb100_init+0x0/0xc @ 1
[ 3.079564] initcall asb100_init+0x0/0xc returned 0 after 5360 usecs
[ 3.079798] calling sensors_w83627hf_init+0x0/0x136 @ 1
[ 3.080039] initcall sensors_w83627hf_init+0x0/0x136 returned -19 after 34 usecs
[ 3.080139] calling sensors_w83792d_init+0x0/0xc @ 1
[ 3.119243] initcall sensors_w83792d_init+0x0/0xc returned 0 after 37743 usecs
[ 3.119589] calling sensors_w83793_init+0x0/0xc @ 1
[ 3.159239] initcall sensors_w83793_init+0x0/0xc returned 0 after 38494 usecs
[ 3.159473] calling sensors_w83795_init+0x0/0xc @ 1
[ 3.199233] initcall sensors_w83795_init+0x0/0xc returned 0 after 38605 usecs
[ 3.199456] calling sensors_w83781d_init+0x0/0x326 @ 1
[ 3.279243] initcall sensors_w83781d_init+0x0/0x326 returned 0 after 77696 usecs
[ 3.279594] calling sensors_w83791d_init+0x0/0xc @ 1
[ 3.319249] initcall sensors_w83791d_init+0x0/0xc returned 0 after 38497 usecs
[ 3.319590] calling abituguru_init+0x0/0x15e @ 1
[ 3.319798] initcall abituguru_init+0x0/0x15e returned -19 after 4 usecs
[ 3.320006] calling abituguru3_init+0x0/0x208 @ 1
[ 3.320091] initcall abituguru3_init+0x0/0x208 returned -19 after 1 usecs
[ 3.320091] calling ad7414_init+0x0/0xc @ 1
[ 3.320091] initcall ad7414_init+0x0/0xc returned 0 after 503 usecs
[ 3.320091] calling ad7418_init+0x0/0xc @ 1
[ 3.320091] initcall ad7418_init+0x0/0xc returned 0 after 401 usecs
[ 3.320091] calling sensors_adm1021_init+0x0/0xc @ 1
[ 3.409252] initcall sensors_adm1021_init+0x0/0xc returned 0 after 84726 usecs
[ 3.409592] calling sensors_adm1025_init+0x0/0xc @ 1
[ 3.439256] initcall sensors_adm1025_init+0x0/0xc returned 0 after 28745 usecs
[ 3.439599] calling sm_adm1026_init+0x0/0xc @ 1
[ 3.469268] initcall sm_adm1026_init+0x0/0xc returned 0 after 28748 usecs
[ 3.469500] calling sensors_adm1029_init+0x0/0xc @ 1
[ 3.549243] initcall sensors_adm1029_init+0x0/0xc returned 0 after 77645 usecs
[ 3.549586] calling sensors_adm1031_init+0x0/0xc @ 1
[ 3.579253] initcall sensors_adm1031_init+0x0/0xc returned 0 after 28744 usecs
[ 3.579597] calling sensors_adm9240_init+0x0/0xc @ 1
[ 3.619251] initcall sensors_adm9240_init+0x0/0xc returned 0 after 38497 usecs
[ 3.619593] calling sensors_ads1015_init+0x0/0xc @ 1
[ 3.620094] initcall sensors_ads1015_init+0x0/0xc returned 0 after 481 usecs
[ 3.620094] calling sensors_ads7828_init+0x0/0x48 @ 1
[ 3.659258] initcall sensors_ads7828_init+0x0/0x48 returned 0 after 34628 usecs
[ 3.659595] calling sensors_adt7411_init+0x0/0xc @ 1
[ 3.689248] initcall sensors_adt7411_init+0x0/0xc returned 0 after 28731 usecs
[ 3.689588] calling adt7462_init+0x0/0xc @ 1
[ 3.709390] initcall adt7462_init+0x0/0xc returned 0 after 19114 usecs
[ 3.709622] calling adt7470_init+0x0/0xc @ 1
[ 3.739260] initcall adt7470_init+0x0/0xc returned 0 after 28720 usecs
[ 3.739491] calling sensors_adt7475_init+0x0/0xc @ 1
[ 3.769262] initcall sensors_adt7475_init+0x0/0xc returned 0 after 28847 usecs
[ 3.769602] calling applesmc_init+0x0/0x2f6 @ 1
[ 3.769808] applesmc: supported laptop not found!
[ 3.769997] applesmc: driver init failed (ret=-19)!
[ 3.770102] initcall applesmc_init+0x0/0x2f6 returned -19 after 385 usecs
[ 3.770102] calling sm_asc7621_init+0x0/0x6e @ 1
[ 3.799243] initcall sm_asc7621_init+0x0/0x6e returned 0 after 27958 usecs
[ 3.799464] calling atxp1_init+0x0/0xc @ 1
[ 3.819292] initcall atxp1_init+0x0/0xc returned 0 after 19146 usecs
[ 3.819521] calling coretemp_init+0x0/0x65 @ 1
[ 3.820103] initcall coretemp_init+0x0/0x65 returned 0 after 508 usecs
[ 3.820103] calling dme1737_init+0x0/0x14e @ 1
[ 3.849292] initcall dme1737_init+0x0/0x14e returned 0 after 27887 usecs
[ 3.849523] calling ds620_init+0x0/0xc @ 1
[ 3.850106] initcall ds620_init+0x0/0xc returned 0 after 485 usecs
[ 3.850106] calling ds1621_init+0x0/0xc @ 1
[ 3.929251] initcall ds1621_init+0x0/0xc returned 0 after 76704 usecs
[ 3.929484] calling sensor_emc1403_init+0x0/0xc @ 1
[ 3.969261] initcall sensor_emc1403_init+0x0/0xc returned 0 after 38621 usecs
[ 3.969484] calling sensors_emc2103_init+0x0/0xc @ 1
[ 3.979342] initcall sensors_emc2103_init+0x0/0xc returned 0 after 9405 usecs
[ 3.979578] calling sensors_emc6w201_init+0x0/0xc @ 1
[ 4.009285] initcall sensors_emc6w201_init+0x0/0xc returned 0 after 28782 usecs
[ 4.009625] calling f71805f_init+0x0/0x12d @ 1
[ 4.009876] initcall f71805f_init+0x0/0x12d returned -19 after 48 usecs
[ 4.010082] calling f71882fg_init+0x0/0x11f @ 1
[ 4.010123] initcall f71882fg_init+0x0/0x11f returned -19 after 58 usecs
[ 4.010123] calling sensors_f75375_init+0x0/0xc @ 1
[ 4.029294] initcall sensors_f75375_init+0x0/0xc returned 0 after 18070 usecs
[ 4.029529] calling fam15h_power_init+0x0/0x11 @ 1
[ 4.030103] initcall fam15h_power_init+0x0/0x11 returned 0 after 902 usecs
[ 4.030103] calling fschmd_init+0x0/0xc @ 1
[ 4.039353] initcall fschmd_init+0x0/0xc returned 0 after 7998 usecs
[ 4.039581] calling g760a_init+0x0/0xc @ 1
[ 4.040158] initcall g760a_init+0x0/0xc returned 0 after 486 usecs
[ 4.040158] calling sensors_gl518sm_init+0x0/0xc @ 1
[ 4.059323] initcall sensors_gl518sm_init+0x0/0xc returned 0 after 18125 usecs
[ 4.059668] calling sensors_gl520sm_init+0x0/0xc @ 1
[ 4.079303] initcall sensors_gl520sm_init+0x0/0xc returned 0 after 18945 usecs
[ 4.079641] calling gpio_fan_init+0x0/0xa @ 1
[ 4.080109] initcall gpio_fan_init+0x0/0xa returned 0 after 488 usecs
[ 4.080109] calling i5k_amb_init+0x0/0x4e @ 1
[ 4.080109] initcall i5k_amb_init+0x0/0x4e returned 0 after 932 usecs
[ 4.080109] calling aem_init+0x0/0x3c @ 1
[ 4.080109] initcall aem_init+0x0/0x3c returned 0 after 434 usecs
[ 4.080109] calling ibmpex_init+0x0/0xa @ 1
[ 4.080109] initcall ibmpex_init+0x0/0xa returned 0 after 1 usecs
[ 4.080109] calling sm_it87_init+0x0/0x3e2 @ 1
[ 4.080109] initcall sm_it87_init+0x0/0x3e2 returned -19 after 40 usecs
[ 4.080109] calling sensors_jc42_init+0x0/0xc @ 1
[ 4.159262] initcall sensors_jc42_init+0x0/0xc returned 0 after 73502 usecs
[ 4.159497] calling k8temp_init+0x0/0x11 @ 1
[ 4.160105] initcall k8temp_init+0x0/0x11 returned 0 after 926 usecs
[ 4.160105] calling k10temp_init+0x0/0x11 @ 1
[ 4.160105] initcall k10temp_init+0x0/0x11 returned 0 after 805 usecs
[ 4.160105] calling pem_init+0x0/0xc @ 1
[ 4.160105] initcall pem_init+0x0/0xc returned 0 after 440 usecs
[ 4.160105] calling sensors_lm63_init+0x0/0xc @ 1
[ 4.189282] initcall sensors_lm63_init+0x0/0xc returned 0 after 25316 usecs
[ 4.189516] calling sensors_lm73_init+0x0/0xc @ 1
[ 4.249264] initcall sensors_lm73_init+0x0/0xc returned 0 after 58116 usecs
[ 4.249499] calling sensors_lm75_init+0x0/0xc @ 1
[ 4.329267] initcall sensors_lm75_init+0x0/0xc returned 0 after 77664 usecs
[ 4.329502] calling sensors_lm77_init+0x0/0xc @ 1
[ 4.369249] initcall sensors_lm77_init+0x0/0xc returned 0 after 38590 usecs
[ 4.369471] calling sm_lm78_init+0x0/0x30b @ 1
[ 4.449262] initcall sm_lm78_init+0x0/0x30b returned 0 after 77699 usecs
[ 4.449495] calling sensors_lm80_init+0x0/0xc @ 1
[ 4.529270] initcall sensors_lm80_init+0x0/0xc returned 0 after 77673 usecs
[ 4.529503] calling sensors_lm83_init+0x0/0xc @ 1
[ 4.619273] initcall sensors_lm83_init+0x0/0xc returned 0 after 87435 usecs
[ 4.619506] calling sm_lm85_init+0x0/0xc @ 1
[ 4.649275] initcall sm_lm85_init+0x0/0xc returned 0 after 28841 usecs
[ 4.649507] calling sensors_lm87_init+0x0/0xc @ 1
[ 4.679282] initcall sensors_lm87_init+0x0/0xc returned 0 after 28845 usecs
[ 4.679516] calling sensors_lm90_init+0x0/0xc @ 1
[ 4.769258] initcall sensors_lm90_init+0x0/0xc returned 0 after 87413 usecs
[ 4.769491] calling sensors_lm92_init+0x0/0xc @ 1
[ 4.809274] initcall sensors_lm92_init+0x0/0xc returned 0 after 38615 usecs
[ 4.809507] calling lm93_init+0x0/0xc @ 1
[ 4.839262] initcall lm93_init+0x0/0xc returned 0 after 28835 usecs
[ 4.839483] calling sensors_lm95241_init+0x0/0xc @ 1
[ 4.869276] initcall sensors_lm95241_init+0x0/0xc returned 0 after 28870 usecs
[ 4.869618] calling ltc4151_init+0x0/0xc @ 1
[ 4.870117] initcall ltc4151_init+0x0/0xc returned 0 after 495 usecs
[ 4.870117] calling ltc4215_init+0x0/0xc @ 1
[ 4.870117] initcall ltc4215_init+0x0/0xc returned 0 after 440 usecs
[ 4.870117] calling ltc4245_init+0x0/0xc @ 1
[ 4.870117] initcall ltc4245_init+0x0/0xc returned 0 after 446 usecs
[ 4.870117] calling ltc4261_init+0x0/0xc @ 1
[ 4.870117] initcall ltc4261_init+0x0/0xc returned 0 after 443 usecs
[ 4.870117] calling max16065_init+0x0/0xc @ 1
[ 4.870117] initcall max16065_init+0x0/0xc returned 0 after 442 usecs
[ 4.870117] calling sensors_max1619_init+0x0/0xc @ 1
[ 4.959275] initcall sensors_max1619_init+0x0/0xc returned 0 after 82794 usecs
[ 4.959617] calling max6639_init+0x0/0xc @ 1
[ 4.960117] i2c-core: driver [max6639] using legacy suspend method
[ 4.960117] i2c-core: driver [max6639] using legacy resume method
[ 4.989284] initcall max6639_init+0x0/0xc returned 0 after 28742 usecs
[ 4.989509] calling max6642_init+0x0/0xc @ 1
[ 5.069276] initcall max6642_init+0x0/0xc returned 0 after 77668 usecs
[ 5.069507] calling sensors_max6650_init+0x0/0xc @ 1
[ 5.070119] initcall sensors_max6650_init+0x0/0xc returned 0 after 519 usecs
[ 5.070119] calling pc87360_init+0x0/0x8a @ 1
[ 5.070119] pc87360: Device 0x09 not activated
[ 5.070119] pc87360: No active logical device, module not inserted
[ 5.070119] initcall pc87360_init+0x0/0x8a returned -19 after 412 usecs
[ 5.070119] calling pc87427_init+0x0/0x164 @ 1
[ 5.070119] initcall pc87427_init+0x0/0x164 returned -19 after 27 usecs
[ 5.070119] calling pcf8591_init+0x0/0x2d @ 1
[ 5.070119] initcall pcf8591_init+0x0/0x2d returned 0 after 519 usecs
[ 5.070119] calling sch5627_init+0x0/0xef @ 1
[ 5.070119] initcall sch5627_init+0x0/0xef returned -19 after 38 usecs
[ 5.070119] calling sht15_init+0x0/0x46 @ 1
[ 5.070119] initcall sht15_init+0x0/0x46 returned 0 after 2423 usecs
[ 5.070119] calling sht21_init+0x0/0xc @ 1
[ 5.070119] initcall sht21_init+0x0/0xc returned 0 after 538 usecs
[ 5.070119] calling sm_sis5595_init+0x0/0x11 @ 1
[ 5.070119] initcall sm_sis5595_init+0x0/0x11 returned 0 after 950 usecs
[ 5.070119] calling smm665_init+0x0/0xc @ 1
[ 5.079692] initcall smm665_init+0x0/0xc returned 0 after 811 usecs
[ 5.079936] calling smsc47b397_init+0x0/0x159 @ 1
[ 5.080156] initcall smsc47b397_init+0x0/0x159 returned -19 after 14 usecs
[ 5.080182] calling sm_smsc47m1_init+0x0/0x21e @ 1
[ 5.080182] initcall sm_smsc47m1_init+0x0/0x21e returned -19 after 14 usecs
[ 5.080182] calling smsc47m192_init+0x0/0xc @ 1
[ 5.099369] initcall smsc47m192_init+0x0/0xc returned 0 after 17906 usecs
[ 5.099605] calling amc6821_init+0x0/0xc @ 1
[ 5.189306] initcall amc6821_init+0x0/0xc returned 0 after 87364 usecs
[ 5.189542] calling sm_thmc50_init+0x0/0xc @ 1
[ 5.219288] initcall sm_thmc50_init+0x0/0xc returned 0 after 28814 usecs
[ 5.219523] calling tmp102_init+0x0/0xc @ 1
[ 5.220125] initcall tmp102_init+0x0/0xc returned 0 after 500 usecs
[ 5.220125] calling tmp401_init+0x0/0xc @ 1
[ 5.229378] initcall tmp401_init+0x0/0xc returned 0 after 8445 usecs
[ 5.229605] calling tmp421_init+0x0/0xc @ 1
[ 5.279284] initcall tmp421_init+0x0/0xc returned 0 after 48283 usecs
[ 5.279517] calling via_cputemp_init+0x0/0x9e @ 1
[ 5.279716] via_cputemp: Not a VIA CPU
[ 5.279913] initcall via_cputemp_init+0x0/0x9e returned -19 after 186 usecs
[ 5.280120] calling sm_via686a_init+0x0/0x11 @ 1
[ 5.280120] initcall sm_via686a_init+0x0/0x11 returned 0 after 914 usecs
[ 5.280120] calling vt1211_init+0x0/0x13f @ 1
[ 5.280120] initcall vt1211_init+0x0/0x13f returned -19 after 33 usecs
[ 5.280120] calling sm_vt8231_init+0x0/0x11 @ 1
[ 5.280120] initcall sm_vt8231_init+0x0/0x11 returned 0 after 723 usecs
[ 5.280120] calling sensors_w83627ehf_init+0x0/0x13f @ 1
[ 5.280120] initcall sensors_w83627ehf_init+0x0/0x13f returned -19 after 61 usecs
[ 5.280120] calling sensors_w83l785ts_init+0x0/0xc @ 1
[ 5.289382] initcall sensors_w83l785ts_init+0x0/0xc returned 0 after 5263 usecs
[ 5.289723] calling sensors_w83l786ng_init+0x0/0xc @ 1
[ 5.309318] initcall sensors_w83l786ng_init+0x0/0xc returned 0 after 18901 usecs
[ 5.309659] calling pmbus_init+0x0/0xc @ 1
[ 5.310132] initcall pmbus_init+0x0/0xc returned 0 after 463 usecs
[ 5.310132] calling adm1275_init+0x0/0xc @ 1
[ 5.310132] initcall adm1275_init+0x0/0xc returned 0 after 414 usecs
[ 5.310132] calling max16064_init+0x0/0xc @ 1
[ 5.310132] initcall max16064_init+0x0/0xc returned 0 after 445 usecs
[ 5.310132] calling max34440_init+0x0/0xc @ 1
[ 5.310132] initcall max34440_init+0x0/0xc returned 0 after 515 usecs
[ 5.310132] calling max8688_init+0x0/0xc @ 1
[ 5.310132] initcall max8688_init+0x0/0xc returned 0 after 458 usecs
[ 5.310132] calling ucd9000_init+0x0/0xc @ 1
[ 5.310132] initcall ucd9000_init+0x0/0xc returned 0 after 454 usecs
[ 5.310132] calling ucd9200_init+0x0/0xc @ 1
[ 5.310132] initcall ucd9200_init+0x0/0xc returned 0 after 457 usecs
[ 5.310132] calling linear_init+0x0/0xa @ 1
[ 5.310132] md: linear personality registered for level -1
[ 5.310132] initcall linear_init+0x0/0xa returned 0 after 195 usecs
[ 5.310132] calling raid0_init+0x0/0xa @ 1
[ 5.310132] md: raid0 personality registered for level 0
[ 5.310132] initcall raid0_init+0x0/0xa returned 0 after 193 usecs
[ 5.310132] calling raid_init+0x0/0xa @ 1
[ 5.310132] md: raid1 personality registered for level 1
[ 5.310132] initcall raid_init+0x0/0xa returned 0 after 194 usecs
[ 5.310132] calling raid_init+0x0/0xa @ 1
[ 5.310132] md: raid10 personality registered for level 10
[ 5.310132] initcall raid_init+0x0/0xa returned 0 after 192 usecs
[ 5.310132] calling raid5_init+0x0/0x21 @ 1
[ 5.310132] md: raid6 personality registered for level 6
[ 5.310132] md: raid5 personality registered for level 5
[ 5.310132] md: raid4 personality registered for level 4
[ 5.310132] initcall raid5_init+0x0/0x21 returned 0 after 576 usecs
[ 5.310132] calling multipath_init+0x0/0xa @ 1
[ 5.310132] md: multipath personality registered for level -4
[ 5.310132] initcall multipath_init+0x0/0xa returned 0 after 195 usecs
[ 5.310132] calling raid_init+0x0/0xa @ 1
[ 5.310132] md: faulty personality registered for level -5
[ 5.310132] initcall raid_init+0x0/0xa returned 0 after 195 usecs
[ 5.310132] calling dm_init+0x0/0x37 @ 1
[ 5.325616] device-mapper: uevent: version 1.0.3
[ 5.325616] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[ 5.325616] initcall dm_init+0x0/0x37 returned 0 after 4467 usecs
[ 5.325616] calling dm_crypt_init+0x0/0x54 @ 1
[ 5.329644] initcall dm_crypt_init+0x0/0x54 returned 0 after 385 usecs
[ 5.329883] calling dm_multipath_init+0x0/0x100 @ 1
[ 5.330168] device-mapper: multipath: version 1.3.0 loaded
[ 5.330168] initcall dm_multipath_init+0x0/0x100 returned 0 after 816 usecs
[ 5.330168] calling dm_rr_init+0x0/0x2d @ 1
[ 5.330168] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 5.330168] initcall dm_rr_init+0x0/0x2d returned 0 after 199 usecs
[ 5.330168] calling dm_ql_init+0x0/0x2d @ 1
[ 5.330168] device-mapper: multipath queue-length: version 0.1.0 loaded
[ 5.330168] initcall dm_ql_init+0x0/0x2d returned 0 after 198 usecs
[ 5.330168] calling dm_st_init+0x0/0x2d @ 1
[ 5.330168] device-mapper: multipath service-time: version 0.2.0 loaded
[ 5.330168] initcall dm_st_init+0x0/0x2d returned 0 after 201 usecs
[ 5.330168] calling dm_snapshot_init+0x0/0x1c2 @ 1
[ 5.330168] initcall dm_snapshot_init+0x0/0x1c2 returned 0 after 288 usecs
[ 5.330168] calling dm_mirror_init+0x0/0x63 @ 1
[ 5.330168] initcall dm_mirror_init+0x0/0x63 returned 0 after 788 usecs
[ 5.330168] calling dm_dirty_log_init+0x0/0x43 @ 1
[ 5.330168] initcall dm_dirty_log_init+0x0/0x43 returned 0 after 3 usecs
[ 5.330168] calling dm_zero_init+0x0/0x22 @ 1
[ 5.330168] initcall dm_zero_init+0x0/0x22 returned 0 after 2 usecs
[ 5.330168] calling dm_raid_init+0x0/0xa @ 1
[ 5.330168] initcall dm_raid_init+0x0/0xa returned 0 after 2 usecs
[ 5.330168] calling edac_init+0x0/0x58 @ 1
[ 5.330168] EDAC MC: Ver: 2.1.0
[ 5.330168] initcall edac_init+0x0/0x58 returned 0 after 1482 usecs
[ 5.330168] calling amd76x_init+0x0/0x24 @ 1
[ 5.339685] initcall amd76x_init+0x0/0x24 returned 0 after 1196 usecs
[ 5.339930] calling i5000_init+0x0/0x2e @ 1
[ 5.340170] initcall i5000_init+0x0/0x2e returned 0 after 950 usecs
[ 5.340170] calling i5100_init+0x0/0x1b @ 1
[ 5.340170] initcall i5100_init+0x0/0x1b returned 0 after 902 usecs
[ 5.340170] calling i5400_init+0x0/0x2e @ 1
[ 5.340170] initcall i5400_init+0x0/0x2e returned 0 after 903 usecs
[ 5.340170] calling i7300_init+0x0/0x2e @ 1
[ 5.340170] initcall i7300_init+0x0/0x2e returned 0 after 885 usecs
[ 5.340170] calling i7core_init+0x0/0x8b @ 1
[ 5.340170] initcall i7core_init+0x0/0x8b returned 0 after 875 usecs
[ 5.340170] calling e7xxx_init+0x0/0x24 @ 1
[ 5.340170] initcall e7xxx_init+0x0/0x24 returned 0 after 885 usecs
[ 5.340170] calling e752x_init+0x0/0x2e @ 1
[ 5.349862] initcall e752x_init+0x0/0x2e returned 0 after 1258 usecs
[ 5.350115] calling i82875p_init+0x0/0x81 @ 1
[ 5.350188] initcall i82875p_init+0x0/0x81 returned -19 after 1419 usecs
[ 5.350188] calling i82975x_init+0x0/0x81 @ 1
[ 5.350188] initcall i82975x_init+0x0/0x81 returned -19 after 1235 usecs
[ 5.350188] calling i3000_init+0x0/0x8b @ 1
[ 5.350188] initcall i3000_init+0x0/0x8b returned -19 after 1342 usecs
[ 5.350188] calling x38_init+0x0/0x8b @ 1
[ 5.350188] initcall x38_init+0x0/0x8b returned -19 after 1346 usecs
[ 5.350188] calling i82860_init+0x0/0x81 @ 1
[ 5.359637] initcall i82860_init+0x0/0x81 returned -19 after 1846 usecs
[ 5.359886] calling r82600_init+0x0/0x24 @ 1
[ 5.360181] initcall r82600_init+0x0/0x24 returned 0 after 914 usecs
[ 5.360181] calling cpufreq_stats_init+0x0/0x80 @ 1
[ 5.360181] initcall cpufreq_stats_init+0x0/0x80 returned 0 after 14 usecs
[ 5.360181] calling cpufreq_gov_powersave_init+0x0/0xa @ 1
[ 5.360181] initcall cpufreq_gov_powersave_init+0x0/0xa returned 0 after 3 usecs
[ 5.360181] calling cpufreq_gov_dbs_init+0x0/0x54 @ 1
[ 5.360181] initcall cpufreq_gov_dbs_init+0x0/0x54 returned 0 after 6 usecs
[ 5.360181] calling cpufreq_gov_dbs_init+0x0/0xa @ 1
[ 5.360181] initcall cpufreq_gov_dbs_init+0x0/0xa returned 0 after 1 usecs
[ 5.360181] calling eps_init+0x0/0x3a @ 1
[ 5.360181] initcall eps_init+0x0/0x3a returned -19 after 1 usecs
[ 5.360181] calling longrun_init+0x0/0x28 @ 1
[ 5.360181] initcall longrun_init+0x0/0x28 returned -19 after 0 usecs
[ 5.360181] calling speedstep_init+0x0/0x17b @ 1
[ 5.360181] initcall speedstep_init+0x0/0x17b returned -19 after 9 usecs
[ 5.360181] calling speedstep_init+0x0/0xa8 @ 1
[ 5.360181] initcall speedstep_init+0x0/0xa8 returned -19 after 3 usecs
[ 5.360181] calling init_ladder+0x0/0xa @ 1
[ 5.360181] cpuidle: using governor ladder
[ 5.360181] initcall init_ladder+0x0/0xa returned 0 after 193 usecs
[ 5.360181] calling init_menu+0x0/0xa @ 1
[ 5.360181] cpuidle: using governor menu
[ 5.360181] initcall init_menu+0x0/0xa returned 0 after 191 usecs
[ 5.360181] calling bd2802_init+0x0/0xc @ 1
[ 5.360181] initcall bd2802_init+0x0/0xc returned 0 after 578 usecs
[ 5.360181] calling clevo_mail_led_init+0x0/0x80 @ 1
[ 5.360181] initcall clevo_mail_led_init+0x0/0x80 returned -19 after 15 usecs
[ 5.360181] calling timer_trig_init+0x0/0xa @ 1
[ 5.360181] initcall timer_trig_init+0x0/0xa returned 0 after 4 usecs
[ 5.360181] calling heartbeat_trig_init+0x0/0xa @ 1
[ 5.360181] initcall heartbeat_trig_init+0x0/0xa returned 0 after 1 usecs
[ 5.360181] calling bl_trig_init+0x0/0xa @ 1
[ 5.360181] initcall bl_trig_init+0x0/0xa returned 0 after 1 usecs
[ 5.360181] calling defon_trig_init+0x0/0xa @ 1
[ 5.360181] initcall defon_trig_init+0x0/0xa returned 0 after 1 usecs
[ 5.360181] calling ib_core_init+0x0/0x81 @ 1
[ 5.370445] initcall ib_core_init+0x0/0x81 returned 0 after 1092 usecs
[ 5.370545] calling ib_mad_init_module+0x0/0xba @ 1
[ 5.370545] initcall ib_mad_init_module+0x0/0xba returned 0 after 217 usecs
[ 5.370545] calling ib_sa_init+0x0/0x51 @ 1
[ 5.370545] initcall ib_sa_init+0x0/0x51 returned 0 after 332 usecs
[ 5.370545] calling ib_cm_init+0x0/0xe4 @ 1
[ 5.370545] initcall ib_cm_init+0x0/0xe4 returned 0 after 825 usecs
[ 5.370545] calling iw_cm_init+0x0/0x28 @ 1
[ 5.370545] initcall iw_cm_init+0x0/0x28 returned 0 after 182 usecs
[ 5.370545] calling addr_init+0x0/0x37 @ 1
[ 5.370545] initcall addr_init+0x0/0x37 returned 0 after 178 usecs
[ 5.370545] calling cma_init+0x0/0xa8 @ 1
[ 5.370545] initcall cma_init+0x0/0xa8 returned 0 after 187 usecs
[ 5.370545] calling ib_umad_init+0x0/0xaa @ 1
[ 5.370545] initcall ib_umad_init+0x0/0xaa returned 0 after 491 usecs
[ 5.370545] calling ib_uverbs_init+0x0/0xaa @ 1
[ 5.370545] initcall ib_uverbs_init+0x0/0xaa returned 0 after 475 usecs
[ 5.370545] calling ib_ucm_init+0x0/0x87 @ 1
[ 5.370545] initcall ib_ucm_init+0x0/0x87 returned 0 after 9 usecs
[ 5.370545] calling ucma_init+0x0/0x78 @ 1
[ 5.370545] initcall ucma_init+0x0/0x78 returned 0 after 737 usecs
[ 5.370545] calling mthca_init+0x0/0x13f @ 1
[ 5.380191] initcall mthca_init+0x0/0x13f returned 0 after 1488 usecs
[ 5.380191] calling c2_init_module+0x0/0x11 @ 1
[ 5.380191] initcall c2_init_module+0x0/0x11 returned 0 after 749 usecs
[ 5.380191] calling iwch_init_module+0x0/0x2f @ 1
[ 5.380191] initcall iwch_init_module+0x0/0x2f returned 0 after 4641 usecs
[ 5.380191] calling mlx4_ib_init+0x0/0x47 @ 1
[ 5.380191] initcall mlx4_ib_init+0x0/0x47 returned 0 after 249 usecs
[ 5.380191] calling nes_init_module+0x0/0xf4 @ 1
[ 5.390082] initcall nes_init_module+0x0/0xf4 returned 0 after 1827 usecs
[ 5.390214] calling ipoib_init_module+0x0/0xd8 @ 1
[ 5.390214] initcall ipoib_init_module+0x0/0xd8 returned 0 after 275 usecs
[ 5.390214] calling srp_init_module+0x0/0x117 @ 1
[ 5.390214] initcall srp_init_module+0x0/0x117 returned 0 after 488 usecs
[ 5.390214] calling iser_init+0x0/0xff @ 1
[ 5.390214] iscsi: registered transport (iser)
[ 5.390214] initcall iser_init+0x0/0xff returned 0 after 1024 usecs
[ 5.390214] calling efivars_init+0x0/0xc7 @ 1
[ 5.390214] EFI Variables Facility v0.08 2004-May-17
[ 5.390214] initcall efivars_init+0x0/0xc7 returned 0 after 191 usecs
[ 5.390214] calling dcdrbu_init+0x0/0x107 @ 1
[ 5.390214] initcall dcdrbu_init+0x0/0x107 returned 0 after 595 usecs
[ 5.390214] calling dcdbas_init+0x0/0x4f @ 1
[ 5.390214] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 5.390214] initcall dcdbas_init+0x0/0x4f returned 0 after 1338 usecs
[ 5.390214] calling ibft_init+0x0/0x2bf @ 1
[ 5.390214] No iBFT detected.
[ 5.390214] initcall ibft_init+0x0/0x2bf returned 0 after 185 usecs
[ 5.390214] calling padlock_init+0x0/0xc2 @ 1
[ 5.390214] padlock_aes: VIA PadLock not detected.
[ 5.390214] initcall padlock_init+0x0/0xc2 returned -19 after 192 usecs
[ 5.390214] calling padlock_init+0x0/0x94 @ 1
[ 5.390214] padlock_sha: VIA PadLock Hash Engine not detected.
[ 5.390214] initcall padlock_init+0x0/0x94 returned -19 after 194 usecs
[ 5.390214] calling geode_aes_init+0x0/0x11 @ 1
[ 5.403363] initcall geode_aes_init+0x0/0x11 returned 0 after 1253 usecs
[ 5.403609] calling hifn_init+0x0/0x11 @ 1
[ 5.403670] HIFN supports only 32-bit addresses.
[ 5.403670] initcall hifn_init+0x0/0x11 returned -22 after 190 usecs
[ 5.403670] initcall hifn_init+0x0/0x11 returned with error code -22
[ 5.403670] calling hid_init+0x0/0x34 @ 1
[ 5.403670] initcall hid_init+0x0/0x34 returned 0 after 523 usecs
[ 5.403670] calling a4_init+0x0/0x11 @ 1
[ 5.403670] initcall a4_init+0x0/0x11 returned 0 after 627 usecs
[ 5.403670] calling apple_init+0x0/0x27 @ 1
[ 5.403670] initcall apple_init+0x0/0x27 returned 0 after 605 usecs
[ 5.403670] calling belkin_init+0x0/0x11 @ 1
[ 5.403670] initcall belkin_init+0x0/0x11 returned 0 after 582 usecs
[ 5.403670] calling ch_init+0x0/0x11 @ 1
[ 5.409854] initcall ch_init+0x0/0x11 returned 0 after 970 usecs
[ 5.410085] calling ch_init+0x0/0x11 @ 1
[ 5.410188] initcall ch_init+0x0/0x11 returned 0 after 565 usecs
[ 5.410188] calling cp_init+0x0/0x11 @ 1
[ 5.410188] initcall cp_init+0x0/0x11 returned 0 after 596 usecs
[ 5.410188] calling ez_init+0x0/0x11 @ 1
[ 5.410188] initcall ez_init+0x0/0x11 returned 0 after 591 usecs
[ 5.410188] calling ks_init+0x0/0x11 @ 1
[ 5.410188] initcall ks_init+0x0/0x11 returned 0 after 595 usecs
[ 5.410188] calling kye_init+0x0/0x11 @ 1
[ 5.410188] initcall kye_init+0x0/0x11 returned 0 after 620 usecs
[ 5.410188] calling lg_init+0x0/0x11 @ 1
[ 5.410188] initcall lg_init+0x0/0x11 returned 0 after 597 usecs
[ 5.410188] calling ms_init+0x0/0x11 @ 1
[ 5.410188] initcall ms_init+0x0/0x11 returned 0 after 608 usecs
[ 5.410188] calling mr_init+0x0/0x11 @ 1
[ 5.410188] initcall mr_init+0x0/0x11 returned 0 after 626 usecs
[ 5.410188] calling hid_init+0x0/0x5f @ 1
[ 5.420190] usbcore: registered new interface driver usbhid
[ 5.420190] usbhid: USB HID core driver
[ 5.420190] initcall hid_init+0x0/0x5f returned 0 after 2156 usecs
[ 5.420190] calling vhost_net_init+0x0/0xa @ 1
[ 5.420190] initcall vhost_net_init+0x0/0xa returned 0 after 694 usecs
[ 5.420190] calling flow_cache_init_global+0x0/0xf9 @ 1
[ 5.420190] initcall flow_cache_init_global+0x0/0xf9 returned 0 after 289 usecs
[ 5.420190] calling pg_init+0x0/0x254 @ 1
[ 5.420190] pktgen: Packet Generator for packet performance testing. Version: 2.74
[ 5.420190] initcall pg_init+0x0/0x254 returned 0 after 672 usecs
[ 5.420190] calling llc_init+0x0/0x17 @ 1
[ 5.420190] initcall llc_init+0x0/0x17 returned 0 after 3 usecs
[ 5.420190] calling snap_init+0x0/0x2d @ 1
[ 5.420190] initcall snap_init+0x0/0x2d returned 0 after 7 usecs
[ 5.420190] calling rif_init+0x0/0x68 @ 1
[ 5.420190] initcall rif_init+0x0/0x68 returned 0 after 56 usecs
[ 5.420190] calling blackhole_module_init+0x0/0xa @ 1
[ 5.420190] initcall blackhole_module_init+0x0/0xa returned 0 after 3 usecs
[ 5.420190] calling police_init_module+0x0/0xa @ 1
[ 5.420190] initcall police_init_module+0x0/0xa returned 0 after 1 usecs
[ 5.420190] calling gact_init_module+0x0/0x15 @ 1
[ 5.420190] GACT probability on
[ 5.420190] initcall gact_init_module+0x0/0x15 returned 0 after 188 usecs
[ 5.420190] calling mirred_init_module+0x0/0x24 @ 1
[ 5.420190] Mirror/redirect action on
[ 5.420190] initcall mirred_init_module+0x0/0x24 returned 0 after 195 usecs
[ 5.420190] calling ipt_init_module+0x0/0xa @ 1
[ 5.420190] initcall ipt_init_module+0x0/0xa returned 0 after 1 usecs
[ 5.420190] calling nat_init_module+0x0/0xa @ 1
[ 5.420190] initcall nat_init_module+0x0/0xa returned 0 after 1 usecs
[ 5.420190] calling pedit_init_module+0x0/0xa @ 1
[ 5.420190] initcall pedit_init_module+0x0/0xa returned 0 after 1 usecs
[ 5.420190] calling simp_init_module+0x0/0x20 @ 1
[ 5.420190] Simple TC action Loaded
[ 5.420190] initcall simp_init_module+0x0/0x20 returned 0 after 189 usecs
[ 5.420190] calling skbedit_init_module+0x0/0xa @ 1
[ 5.420190] initcall skbedit_init_module+0x0/0xa returned 0 after 1 usecs
[ 5.420190] calling cbq_module_init+0x0/0xa @ 1
[ 5.420190] initcall cbq_module_init+0x0/0xa returned 0 after 1 usecs
[ 5.420190] calling htb_module_init+0x0/0xa @ 1
[ 5.420190] initcall htb_module_init+0x0/0xa returned 0 after 1 usecs
[ 5.420190] calling hfsc_init+0x0/0xa @ 1
[ 5.420190] initcall hfsc_init+0x0/0xa returned 0 after 1 usecs
[ 5.420190] calling red_module_init+0x0/0xa @ 1
[ 5.420190] initcall red_module_init+0x0/0xa returned 0 after 2 usecs
[ 5.420190] calling gred_module_init+0x0/0xa @ 1
[ 5.420190] initcall gred_module_init+0x0/0xa returned 0 after 3 usecs
[ 5.420190] calling ingress_module_init+0x0/0xa @ 1
[ 5.420190] initcall ingress_module_init+0x0/0xa returned 0 after 2 usecs
[ 5.420190] calling dsmark_module_init+0x0/0xa @ 1
[ 5.420190] initcall dsmark_module_init+0x0/0xa returned 0 after 2 usecs
[ 5.420190] calling sfq_module_init+0x0/0xa @ 1
[ 5.420190] initcall sfq_module_init+0x0/0xa returned 0 after 2 usecs
[ 5.420190] calling tbf_module_init+0x0/0xa @ 1
[ 5.420190] initcall tbf_module_init+0x0/0xa returned 0 after 2 usecs
[ 5.420190] calling teql_init+0x0/0xb4 @ 1
[ 5.435524] initcall teql_init+0x0/0xb4 returned 0 after 2364 usecs
[ 5.435524] calling prio_module_init+0x0/0xa @ 1
[ 5.435524] initcall prio_module_init+0x0/0xa returned 0 after 2 usecs
[ 5.435524] calling multiq_module_init+0x0/0xa @ 1
[ 5.435524] initcall multiq_module_init+0x0/0xa returned 0 after 2 usecs
[ 5.435524] calling netem_module_init+0x0/0x15 @ 1
[ 5.435524] netem: version 1.3
[ 5.435524] initcall netem_module_init+0x0/0x15 returned 0 after 187 usecs
[ 5.435524] calling init_u32+0x0/0x35 @ 1
[ 5.435524] u32 classifier
[ 5.435524] Performance counters on
[ 5.435524] input device check on
[ 5.435524] Actions configured
[ 5.435524] initcall init_u32+0x0/0x35 returned 0 after 713 usecs
[ 5.435524] calling init_route4+0x0/0xa @ 1
[ 5.435524] initcall init_route4+0x0/0xa returned 0 after 1 usecs
[ 5.435524] calling init_fw+0x0/0xa @ 1
[ 5.435524] initcall init_fw+0x0/0xa returned 0 after 1 usecs
[ 5.435524] calling init_rsvp+0x0/0xa @ 1
[ 5.435524] initcall init_rsvp+0x0/0xa returned 0 after 1 usecs
[ 5.435524] calling init_tcindex+0x0/0xa @ 1
[ 5.435524] initcall init_tcindex+0x0/0xa returned 0 after 1 usecs
[ 5.435524] calling init_rsvp+0x0/0xa @ 1
[ 5.435524] initcall init_rsvp+0x0/0xa returned 0 after 2 usecs
[ 5.435524] calling init_basic+0x0/0xa @ 1
[ 5.435524] initcall init_basic+0x0/0xa returned 0 after 1 usecs
[ 5.435524] calling cls_flow_init+0x0/0xa @ 1
[ 5.435524] initcall cls_flow_init+0x0/0xa returned 0 after 1 usecs
[ 5.435524] calling init_em_cmp+0x0/0xa @ 1
[ 5.435524] initcall init_em_cmp+0x0/0xa returned 0 after 1 usecs
[ 5.435524] calling init_em_nbyte+0x0/0xa @ 1
[ 5.435524] initcall init_em_nbyte+0x0/0xa returned 0 after 0 usecs
[ 5.435524] calling init_em_u32+0x0/0xa @ 1
[ 5.435524] initcall init_em_u32+0x0/0xa returned 0 after 0 usecs
[ 5.435524] calling init_em_meta+0x0/0xa @ 1
[ 5.435524] initcall init_em_meta+0x0/0xa returned 0 after 0 usecs
[ 5.435524] calling init_em_text+0x0/0xa @ 1
[ 5.435524] initcall init_em_text+0x0/0xa returned 0 after 1 usecs
[ 5.435524] calling nfnetlink_init+0x0/0x1b @ 1
[ 5.435524] Netfilter messages via NETLINK v0.30.
[ 5.444958] initcall nfnetlink_init+0x0/0x1b returned 0 after 562 usecs
[ 5.445187] calling nfnetlink_queue_init+0x0/0x81 @ 1
[ 5.445437] initcall nfnetlink_queue_init+0x0/0x81 returned 0 after 40 usecs
[ 5.445654] calling nfnetlink_log_init+0x0/0xad @ 1
[ 5.445655] initcall nfnetlink_log_init+0x0/0xad returned 0 after 39 usecs
[ 5.445655] calling nf_conntrack_standalone_init+0x0/0xa @ 1
[ 5.445655] nf_conntrack version 0.5.0 (4546 buckets, 18184 max)
[ 5.445655] initcall nf_conntrack_standalone_init+0x0/0xa returned 0 after 1725 usecs
[ 5.445655] calling nf_conntrack_proto_dccp_init+0x0/0x4d @ 1
[ 5.445655] initcall nf_conntrack_proto_dccp_init+0x0/0x4d returned 0 after 59 usecs
[ 5.445655] calling nf_ct_proto_gre_init+0x0/0x2f @ 1
[ 5.445655] initcall nf_ct_proto_gre_init+0x0/0x2f returned 0 after 10 usecs
[ 5.445655] calling nf_conntrack_proto_sctp_init+0x0/0x47 @ 1
[ 5.445655] initcall nf_conntrack_proto_sctp_init+0x0/0x47 returned 0 after 15 usecs
[ 5.445655] calling nf_conntrack_proto_udplite_init+0x0/0x33 @ 1
[ 5.445655] initcall nf_conntrack_proto_udplite_init+0x0/0x33 returned 0 after 11 usecs
[ 5.445655] calling ctnetlink_init+0x0/0xaa @ 1
[ 5.445655] ctnetlink v0.93: registering with nfnetlink.
[ 5.445655] initcall ctnetlink_init+0x0/0xaa returned 0 after 198 usecs
[ 5.445655] calling nf_conntrack_amanda_init+0x0/0x8b @ 1
[ 5.445655] initcall nf_conntrack_amanda_init+0x0/0x8b returned 0 after 14 usecs
[ 5.445655] calling nf_conntrack_ftp_init+0x0/0x166 @ 1
[ 5.445655] initcall nf_conntrack_ftp_init+0x0/0x166 returned 0 after 16 usecs
[ 5.445655] calling nf_conntrack_h323_init+0x0/0xac @ 1
[ 5.445655] initcall nf_conntrack_h323_init+0x0/0xac returned 0 after 10 usecs
[ 5.445655] calling nf_conntrack_irc_init+0x0/0x126 @ 1
[ 5.445655] initcall nf_conntrack_irc_init+0x0/0x126 returned 0 after 7 usecs
[ 5.445655] calling nf_conntrack_netbios_ns_init+0x0/0x14 @ 1
[ 5.445655] initcall nf_conntrack_netbios_ns_init+0x0/0x14 returned 0 after 2 usecs
[ 5.445655] calling nf_conntrack_snmp_init+0x0/0x14 @ 1
[ 5.445655] initcall nf_conntrack_snmp_init+0x0/0x14 returned 0 after 1 usecs
[ 5.445655] calling nf_conntrack_pptp_init+0x0/0x2f @ 1
[ 5.445655] initcall nf_conntrack_pptp_init+0x0/0x2f returned 0 after 2 usecs
[ 5.445655] calling nf_conntrack_sane_init+0x0/0x166 @ 1
[ 5.445655] initcall nf_conntrack_sane_init+0x0/0x166 returned 0 after 9 usecs
[ 5.445655] calling nf_conntrack_sip_init+0x0/0x18b @ 1
[ 5.445655] initcall nf_conntrack_sip_init+0x0/0x18b returned 0 after 5 usecs
[ 5.445655] calling nf_conntrack_tftp_init+0x0/0x13e @ 1
[ 5.445655] initcall nf_conntrack_tftp_init+0x0/0x13e returned 0 after 3 usecs
[ 5.445655] calling nf_tproxy_init+0x0/0x19 @ 1
[ 5.445655] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 5.445655] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 5.445655] initcall nf_tproxy_init+0x0/0x19 returned 0 after 392 usecs
[ 5.445655] calling xt_init+0x0/0xae @ 1
[ 5.445655] initcall xt_init+0x0/0xae returned 0 after 7 usecs
[ 5.445655] calling tcpudp_mt_init+0x0/0xf @ 1
[ 5.445655] initcall tcpudp_mt_init+0x0/0xf returned 0 after 3 usecs
[ 5.445655] calling mark_mt_init+0x0/0x33 @ 1
[ 5.445655] initcall mark_mt_init+0x0/0x33 returned 0 after 1 usecs
[ 5.445655] calling connmark_mt_init+0x0/0x33 @ 1
[ 5.445655] initcall connmark_mt_init+0x0/0x33 returned 0 after 1 usecs
[ 5.445655] calling audit_tg_init+0x0/0xf @ 1
[ 5.445655] initcall audit_tg_init+0x0/0xf returned 0 after 1 usecs
[ 5.445655] calling checksum_tg_init+0x0/0xa @ 1
[ 5.445655] initcall checksum_tg_init+0x0/0xa returned 0 after 1 usecs
[ 5.445655] calling classify_tg_init+0x0/0xf @ 1
[ 5.445655] initcall classify_tg_init+0x0/0xf returned 0 after 1 usecs
[ 5.445655] calling connsecmark_tg_init+0x0/0xa @ 1
[ 5.445655] initcall connsecmark_tg_init+0x0/0xa returned 0 after 0 usecs
[ 5.445655] calling xt_ct_tg_init+0x0/0xa @ 1
[ 5.445655] initcall xt_ct_tg_init+0x0/0xa returned 0 after 1 usecs
[ 5.445655] calling dscp_tg_init+0x0/0xf @ 1
[ 5.445655] initcall dscp_tg_init+0x0/0xf returned 0 after 1 usecs
[ 5.445655] calling hl_tg_init+0x0/0xf @ 1
[ 5.445655] initcall hl_tg_init+0x0/0xf returned 0 after 1 usecs
[ 5.445655] calling led_tg_init+0x0/0xa @ 1
[ 5.445655] initcall led_tg_init+0x0/0xa returned 0 after 0 usecs
[ 5.445655] calling nflog_tg_init+0x0/0xa @ 1
[ 5.445655] initcall nflog_tg_init+0x0/0xa returned 0 after 1 usecs
[ 5.445655] calling nfqueue_tg_init+0x0/0xf @ 1
[ 5.445655] initcall nfqueue_tg_init+0x0/0xf returned 0 after 2 usecs
[ 5.445655] calling notrack_tg_init+0x0/0xa @ 1
[ 5.445655] initcall notrack_tg_init+0x0/0xa returned 0 after 1 usecs
[ 5.445655] calling xt_rateest_tg_init+0x0/0x1d @ 1
[ 5.445655] initcall xt_rateest_tg_init+0x0/0x1d returned 0 after 1 usecs
[ 5.445655] calling secmark_tg_init+0x0/0xa @ 1
[ 5.445655] initcall secmark_tg_init+0x0/0xa returned 0 after 1 usecs
[ 5.445655] calling tproxy_tg_init+0x0/0x19 @ 1
[ 5.445655] initcall tproxy_tg_init+0x0/0x19 returned 0 after 2 usecs
[ 5.445655] calling tcpmss_tg_init+0x0/0xf @ 1
[ 5.445655] initcall tcpmss_tg_init+0x0/0xf returned 0 after 1 usecs
[ 5.445655] calling tcpoptstrip_tg_init+0x0/0xf @ 1
[ 5.445655] initcall tcpoptstrip_tg_init+0x0/0xf returned 0 after 1 usecs
[ 5.445655] calling tee_tg_init+0x0/0xf @ 1
[ 5.445655] initcall tee_tg_init+0x0/0xf returned 0 after 1 usecs
[ 5.445655] calling trace_tg_init+0x0/0xa @ 1
[ 5.445655] initcall trace_tg_init+0x0/0xa returned 0 after 0 usecs
[ 5.445655] calling idletimer_tg_init+0x0/0x78 @ 1
[ 5.470469] initcall idletimer_tg_init+0x0/0x78 returned 0 after 1432 usecs
[ 5.470469] calling addrtype_mt_init+0x0/0xf @ 1
[ 5.470469] initcall addrtype_mt_init+0x0/0xf returned 0 after 2 usecs
[ 5.470469] calling xt_cluster_mt_init+0x0/0xa @ 1
[ 5.470469] initcall xt_cluster_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling comment_mt_init+0x0/0xa @ 1
[ 5.470469] initcall comment_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling connbytes_mt_init+0x0/0xa @ 1
[ 5.470469] initcall connbytes_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling connlimit_mt_init+0x0/0xf @ 1
[ 5.470469] initcall connlimit_mt_init+0x0/0xf returned 0 after 1 usecs
[ 5.470469] calling conntrack_mt_init+0x0/0xf @ 1
[ 5.470469] initcall conntrack_mt_init+0x0/0xf returned 0 after 2 usecs
[ 5.470469] calling dccp_mt_init+0x0/0x4a @ 1
[ 5.470469] initcall dccp_mt_init+0x0/0x4a returned 0 after 3 usecs
[ 5.470469] calling devgroup_mt_init+0x0/0xa @ 1
[ 5.470469] initcall devgroup_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling dscp_mt_init+0x0/0xf @ 1
[ 5.470469] initcall dscp_mt_init+0x0/0xf returned 0 after 2 usecs
[ 5.470469] calling esp_mt_init+0x0/0xf @ 1
[ 5.470469] initcall esp_mt_init+0x0/0xf returned 0 after 1 usecs
[ 5.470469] calling hashlimit_mt_init+0x0/0x75 @ 1
[ 5.470469] initcall hashlimit_mt_init+0x0/0x75 returned 0 after 280 usecs
[ 5.470469] calling helper_mt_init+0x0/0xa @ 1
[ 5.470469] initcall helper_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling hl_mt_init+0x0/0xf @ 1
[ 5.470469] initcall hl_mt_init+0x0/0xf returned 0 after 1 usecs
[ 5.470469] calling iprange_mt_init+0x0/0xf @ 1
[ 5.470469] initcall iprange_mt_init+0x0/0xf returned 0 after 1 usecs
[ 5.470469] calling ipvs_mt_init+0x0/0xa @ 1
[ 5.470469] initcall ipvs_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling length_mt_init+0x0/0xf @ 1
[ 5.470469] initcall length_mt_init+0x0/0xf returned 0 after 1 usecs
[ 5.470469] calling limit_mt_init+0x0/0xa @ 1
[ 5.470469] initcall limit_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling mac_mt_init+0x0/0xa @ 1
[ 5.470469] initcall mac_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling multiport_mt_init+0x0/0xf @ 1
[ 5.470469] initcall multiport_mt_init+0x0/0xf returned 0 after 1 usecs
[ 5.470469] calling xt_osf_init+0x0/0x73 @ 1
[ 5.470469] initcall xt_osf_init+0x0/0x73 returned 0 after 3 usecs
[ 5.470469] calling owner_mt_init+0x0/0xa @ 1
[ 5.470469] initcall owner_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling physdev_mt_init+0x0/0xa @ 1
[ 5.470469] initcall physdev_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling pkttype_mt_init+0x0/0xa @ 1
[ 5.470469] initcall pkttype_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling policy_mt_init+0x0/0xf @ 1
[ 5.470469] initcall policy_mt_init+0x0/0xf returned 0 after 1 usecs
[ 5.470469] calling quota_mt_init+0x0/0xa @ 1
[ 5.470469] initcall quota_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling xt_rateest_mt_init+0x0/0xa @ 1
[ 5.470469] initcall xt_rateest_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling realm_mt_init+0x0/0xa @ 1
[ 5.470469] initcall realm_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling recent_mt_init+0x0/0x6c @ 1
[ 5.470469] initcall recent_mt_init+0x0/0x6c returned 0 after 26 usecs
[ 5.470469] calling sctp_mt_init+0x0/0xf @ 1
[ 5.470469] initcall sctp_mt_init+0x0/0xf returned 0 after 1 usecs
[ 5.470469] calling socket_mt_init+0x0/0x19 @ 1
[ 5.470469] initcall socket_mt_init+0x0/0x19 returned 0 after 2 usecs
[ 5.470469] calling state_mt_init+0x0/0xa @ 1
[ 5.470469] initcall state_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling statistic_mt_init+0x0/0xa @ 1
[ 5.470469] initcall statistic_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling string_mt_init+0x0/0xa @ 1
[ 5.470469] initcall string_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling tcpmss_mt_init+0x0/0xf @ 1
[ 5.470469] initcall tcpmss_mt_init+0x0/0xf returned 0 after 1 usecs
[ 5.470469] calling time_mt_init+0x0/0x3f @ 1
[ 5.470469] xt_time: kernel timezone is -0000
[ 5.470469] initcall time_mt_init+0x0/0x3f returned 0 after 191 usecs
[ 5.470469] calling u32_mt_init+0x0/0xa @ 1
[ 5.470469] initcall u32_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling ip_set_init+0x0/0xbb @ 1
[ 5.470469] ip_set: protocol 6
[ 5.470469] initcall ip_set_init+0x0/0xbb returned 0 after 190 usecs
[ 5.470469] calling bitmap_ip_init+0x0/0xa @ 1
[ 5.470469] initcall bitmap_ip_init+0x0/0xa returned 0 after 2 usecs
[ 5.470469] calling bitmap_ipmac_init+0x0/0xa @ 1
[ 5.470469] initcall bitmap_ipmac_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling bitmap_port_init+0x0/0xa @ 1
[ 5.470469] initcall bitmap_port_init+0x0/0xa returned 0 after 2 usecs
[ 5.470469] calling hash_ip_init+0x0/0xa @ 1
[ 5.470469] initcall hash_ip_init+0x0/0xa returned 0 after 1 usecs
[ 5.470469] calling hash_ipport_init+0x0/0xa @ 1
[ 5.470469] initcall hash_ipport_init+0x0/0xa returned 0 after 2 usecs
[ 5.470469] calling hash_ipportip_init+0x0/0xa @ 1
[ 5.470469] initcall hash_ipportip_init+0x0/0xa returned 0 after 2 usecs
[ 5.470469] calling hash_ipportnet_init+0x0/0xa @ 1
[ 5.470469] initcall hash_ipportnet_init+0x0/0xa returned 0 after 2 usecs
[ 5.470469] calling hash_net_init+0x0/0xa @ 1
[ 5.470469] initcall hash_net_init+0x0/0xa returned 0 after 2 usecs
[ 5.470469] calling hash_netport_init+0x0/0xa @ 1
[ 5.470469] initcall hash_netport_init+0x0/0xa returned 0 after 2 usecs
[ 5.470469] calling list_set_init+0x0/0xa @ 1
[ 5.470469] initcall list_set_init+0x0/0xa returned 0 after 2 usecs
[ 5.470469] calling ip_vs_init+0x0/0xf9 @ 1
[ 5.470469] IPVS: Registered protocols (TCP, UDP, SCTP, AH, ESP)
[ 5.492166] IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
[ 5.492672] IPVS: Creating netns size=1156 id=0
[ 5.492672] IPVS: ipvs loaded.
[ 5.492672] initcall ip_vs_init+0x0/0xf9 returned 0 after 2093 usecs
[ 5.492672] calling ip_vs_rr_init+0x0/0xa @ 1
[ 5.492672] IPVS: [rr] scheduler registered.
[ 5.492672] initcall ip_vs_rr_init+0x0/0xa returned 0 after 194 usecs
[ 5.492672] calling ip_vs_wrr_init+0x0/0xa @ 1
[ 5.492672] IPVS: [wrr] scheduler registered.
[ 5.492672] initcall ip_vs_wrr_init+0x0/0xa returned 0 after 190 usecs
[ 5.492672] calling ip_vs_lc_init+0x0/0xa @ 1
[ 5.492672] IPVS: [lc] scheduler registered.
[ 5.492672] initcall ip_vs_lc_init+0x0/0xa returned 0 after 184 usecs
[ 5.492672] calling ip_vs_wlc_init+0x0/0xa @ 1
[ 5.492672] IPVS: [wlc] scheduler registered.
[ 5.492672] initcall ip_vs_wlc_init+0x0/0xa returned 0 after 184 usecs
[ 5.492672] calling ip_vs_lblc_init+0x0/0x2f @ 1
[ 5.492672] IPVS: [lblc] scheduler registered.
[ 5.492672] initcall ip_vs_lblc_init+0x0/0x2f returned 0 after 223 usecs
[ 5.492672] calling ip_vs_lblcr_init+0x0/0x2f @ 1
[ 5.492672] IPVS: [lblcr] scheduler registered.
[ 5.492672] initcall ip_vs_lblcr_init+0x0/0x2f returned 0 after 246 usecs
[ 5.492672] calling ip_vs_dh_init+0x0/0xa @ 1
[ 5.492672] IPVS: [dh] scheduler registered.
[ 5.492672] initcall ip_vs_dh_init+0x0/0xa returned 0 after 191 usecs
[ 5.492672] calling ip_vs_sh_init+0x0/0xa @ 1
[ 5.492672] IPVS: [sh] scheduler registered.
[ 5.492672] initcall ip_vs_sh_init+0x0/0xa returned 0 after 192 usecs
[ 5.492672] calling ip_vs_sed_init+0x0/0xa @ 1
[ 5.492672] IPVS: [sed] scheduler registered.
[ 5.492672] initcall ip_vs_sed_init+0x0/0xa returned 0 after 195 usecs
[ 5.492672] calling ip_vs_nq_init+0x0/0xa @ 1
[ 5.492672] IPVS: [nq] scheduler registered.
[ 5.492672] initcall ip_vs_nq_init+0x0/0xa returned 0 after 190 usecs
[ 5.492672] calling ip_vs_ftp_init+0x0/0xa @ 1
[ 5.492672] IPVS: ftp: loaded support on port[0] = 21
[ 5.492672] initcall ip_vs_ftp_init+0x0/0xa returned 0 after 206 usecs
[ 5.492672] calling ip_vs_sip_init+0x0/0xa @ 1
[ 5.492672] IPVS: [sip] pe registered.
[ 5.492672] initcall ip_vs_sip_init+0x0/0xa returned 0 after 188 usecs
[ 5.492672] calling sysctl_ipv4_init+0x0/0x6d @ 1
[ 5.492672] initcall sysctl_ipv4_init+0x0/0x6d returned 0 after 64 usecs
[ 5.492672] calling ipip_init+0x0/0x4a @ 1
[ 5.492672] IPv4 over IPv4 tunneling driver
[ 5.506354] initcall ipip_init+0x0/0x4a returned 0 after 2472 usecs
[ 5.506354] calling init_syncookies+0x0/0x12 @ 1
[ 5.506354] initcall init_syncookies+0x0/0x12 returned 0 after 163 usecs
[ 5.506354] calling tunnel4_init+0x0/0x5b @ 1
[ 5.506354] initcall tunnel4_init+0x0/0x5b returned 0 after 1 usecs
[ 5.506354] calling ipv4_netfilter_init+0x0/0xa @ 1
[ 5.506354] initcall ipv4_netfilter_init+0x0/0xa returned 0 after 2 usecs
[ 5.506354] calling nf_conntrack_l3proto_ipv4_init+0x0/0xf8 @ 1
[ 5.506354] initcall nf_conntrack_l3proto_ipv4_init+0x0/0xf8 returned 0 after 54 usecs
[ 5.506354] calling nf_nat_init+0x0/0xe7 @ 1
[ 5.506354] initcall nf_nat_init+0x0/0xe7 returned 0 after 108 usecs
[ 5.506354] calling nf_defrag_init+0x0/0xf @ 1
[ 5.506354] initcall nf_defrag_init+0x0/0xf returned 0 after 3 usecs
[ 5.506354] calling nf_nat_amanda_init+0x0/0x1a @ 1
[ 5.506354] initcall nf_nat_amanda_init+0x0/0x1a returned 0 after 0 usecs
[ 5.506354] calling nf_nat_ftp_init+0x0/0x1a @ 1
[ 5.506354] initcall nf_nat_ftp_init+0x0/0x1a returned 0 after 0 usecs
[ 5.506354] calling init+0x0/0xd2 @ 1
[ 5.506354] initcall init+0x0/0xd2 returned 0 after 1 usecs
[ 5.506354] calling nf_nat_irc_init+0x0/0x1a @ 1
[ 5.506354] initcall nf_nat_irc_init+0x0/0x1a returned 0 after 1 usecs
[ 5.506354] calling nf_nat_helper_pptp_init+0x0/0x64 @ 1
[ 5.506354] initcall nf_nat_helper_pptp_init+0x0/0x64 returned 0 after 1 usecs
[ 5.506354] calling nf_nat_sip_init+0x0/0xa4 @ 1
[ 5.506354] initcall nf_nat_sip_init+0x0/0xa4 returned 0 after 1 usecs
[ 5.506354] calling nf_nat_snmp_basic_init+0x0/0x36 @ 1
[ 5.506354] initcall nf_nat_snmp_basic_init+0x0/0x36 returned 0 after 3 usecs
[ 5.506354] calling nf_nat_tftp_init+0x0/0x1a @ 1
[ 5.506354] initcall nf_nat_tftp_init+0x0/0x1a returned 0 after 1 usecs
[ 5.506354] calling nf_nat_proto_dccp_init+0x0/0xa @ 1
[ 5.506354] initcall nf_nat_proto_dccp_init+0x0/0xa returned 0 after 1 usecs
[ 5.506354] calling nf_nat_proto_gre_init+0x0/0xa @ 1
[ 5.506354] initcall nf_nat_proto_gre_init+0x0/0xa returned 0 after 1 usecs
[ 5.506354] calling nf_nat_proto_udplite_init+0x0/0xa @ 1
[ 5.506354] initcall nf_nat_proto_udplite_init+0x0/0xa returned 0 after 1 usecs
[ 5.506354] calling nf_nat_proto_sctp_init+0x0/0xa @ 1
[ 5.506354] initcall nf_nat_proto_sctp_init+0x0/0xa returned 0 after 1 usecs
[ 5.506354] calling ip_tables_init+0x0/0x86 @ 1
[ 5.506354] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 5.506354] initcall ip_tables_init+0x0/0x86 returned 0 after 281 usecs
[ 5.506354] calling iptable_filter_init+0x0/0x57 @ 1
[ 5.516878] initcall iptable_filter_init+0x0/0x57 returned 0 after 377 usecs
[ 5.517114] calling iptable_mangle_init+0x0/0x3c @ 1
[ 5.517402] initcall iptable_mangle_init+0x0/0x3c returned 0 after 77 usecs
[ 5.517558] calling nf_nat_standalone_init+0x0/0x6d @ 1
[ 5.517558] initcall nf_nat_standalone_init+0x0/0x6d returned 0 after 58 usecs
[ 5.517558] calling iptable_raw_init+0x0/0x3c @ 1
[ 5.517558] initcall iptable_raw_init+0x0/0x3c returned 0 after 48 usecs
[ 5.517558] calling ah_mt_init+0x0/0xa @ 1
[ 5.517558] initcall ah_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.517558] calling ecn_mt_init+0x0/0xa @ 1
[ 5.517558] initcall ecn_mt_init+0x0/0xa returned 0 after 1 usecs
[ 5.517558] calling clusterip_tg_init+0x0/0x79 @ 1
[ 5.517558] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
[ 5.517558] initcall clusterip_tg_init+0x0/0x79 returned 0 after 244 usecs
[ 5.517558] calling ecn_tg_init+0x0/0xa @ 1
[ 5.517558] initcall ecn_tg_init+0x0/0xa returned 0 after 1 usecs
[ 5.517558] calling log_tg_init+0x0/0x20 @ 1
[ 5.517558] initcall log_tg_init+0x0/0x20 returned 0 after 5 usecs
[ 5.517558] calling masquerade_tg_init+0x0/0x29 @ 1
[ 5.517558] initcall masquerade_tg_init+0x0/0x29 returned 0 after 17 usecs
[ 5.517558] calling netmap_tg_init+0x0/0xa @ 1
[ 5.517558] initcall netmap_tg_init+0x0/0xa returned 0 after 1 usecs
[ 5.517558] calling redirect_tg_init+0x0/0xa @ 1
[ 5.517558] initcall redirect_tg_init+0x0/0xa returned 0 after 1 usecs
[ 5.517558] calling reject_tg_init+0x0/0xa @ 1
[ 5.517558] initcall reject_tg_init+0x0/0xa returned 0 after 1 usecs
[ 5.517558] calling ulog_tg_init+0x0/0xb3 @ 1
[ 5.523304] initcall ulog_tg_init+0x0/0xb3 returned 0 after 389 usecs
[ 5.523537] calling arp_tables_init+0x0/0x62 @ 1
[ 5.523791] arp_tables: (C) 2002 David S. Miller
[ 5.523977] initcall arp_tables_init+0x0/0x62 returned 0 after 250 usecs
[ 5.523977] calling arpt_mangle_init+0x0/0xa @ 1
[ 5.523977] initcall arpt_mangle_init+0x0/0xa returned 0 after 1 usecs
[ 5.523977] calling arptable_filter_init+0x0/0x3c @ 1
[ 5.523977] initcall arptable_filter_init+0x0/0x3c returned 0 after 84 usecs
[ 5.523977] calling ip_queue_init+0x0/0x104 @ 1
[ 5.523977] initcall ip_queue_init+0x0/0x104 returned 0 after 100 usecs
[ 5.523977] calling inet_diag_init+0x0/0x61 @ 1
[ 5.523977] initcall inet_diag_init+0x0/0x61 returned 0 after 22 usecs
[ 5.523977] calling tcp_diag_init+0x0/0xa @ 1
[ 5.523977] initcall tcp_diag_init+0x0/0xa returned 0 after 1 usecs
[ 5.523977] calling bictcp_register+0x0/0xa @ 1
[ 5.523977] TCP bic registered
[ 5.523977] initcall bictcp_register+0x0/0xa returned 0 after 193 usecs
[ 5.523977] calling cubictcp_register+0x0/0x6c @ 1
[ 5.523977] TCP cubic registered
[ 5.523977] initcall cubictcp_register+0x0/0x6c returned 0 after 189 usecs
[ 5.523977] calling tcp_westwood_register+0x0/0xa @ 1
[ 5.523977] TCP westwood registered
[ 5.523977] initcall tcp_westwood_register+0x0/0xa returned 0 after 189 usecs
[ 5.523977] calling hstcp_register+0x0/0xa @ 1
[ 5.523977] TCP highspeed registered
[ 5.523977] initcall hstcp_register+0x0/0xa returned 0 after 188 usecs
[ 5.523977] calling hybla_register+0x0/0xa @ 1
[ 5.523977] TCP hybla registered
[ 5.523977] initcall hybla_register+0x0/0xa returned 0 after 187 usecs
[ 5.523977] calling htcp_register+0x0/0xa @ 1
[ 5.523977] TCP htcp registered
[ 5.523977] initcall htcp_register+0x0/0xa returned 0 after 186 usecs
[ 5.523977] calling tcp_vegas_register+0x0/0xd @ 1
[ 5.523977] TCP vegas registered
[ 5.523977] initcall tcp_vegas_register+0x0/0xd returned 0 after 187 usecs
[ 5.523977] calling tcp_veno_register+0x0/0xd @ 1
[ 5.523977] TCP veno registered
[ 5.523977] initcall tcp_veno_register+0x0/0xd returned 0 after 187 usecs
[ 5.523977] calling tcp_scalable_register+0x0/0xa @ 1
[ 5.523977] TCP scalable registered
[ 5.523977] initcall tcp_scalable_register+0x0/0xa returned 0 after 187 usecs
[ 5.523977] calling tcp_lp_register+0x0/0xa @ 1
[ 5.523977] TCP lp registered
[ 5.523977] initcall tcp_lp_register+0x0/0xa returned 0 after 188 usecs
[ 5.523977] calling tcp_yeah_register+0x0/0xd @ 1
[ 5.523977] TCP yeah registered
[ 5.523977] initcall tcp_yeah_register+0x0/0xd returned 0 after 188 usecs
[ 5.523977] calling tcp_illinois_register+0x0/0xa @ 1
[ 5.523977] TCP illinois registered
[ 5.523977] initcall tcp_illinois_register+0x0/0xa returned 0 after 190 usecs
[ 5.523977] calling xfrm_user_init+0x0/0x3a @ 1
[ 5.523977] Initializing XFRM netlink socket
[ 5.534376] initcall xfrm_user_init+0x0/0x3a returned 0 after 409 usecs
[ 5.534602] calling inet6_init+0x0/0x28d @ 1
[ 5.535206] NET: Registered protocol family 10
[ 5.540371] initcall inet6_init+0x0/0x28d returned 0 after 7645 usecs
[ 5.540371] calling ah6_init+0x0/0x5b @ 1
[ 5.540371] initcall ah6_init+0x0/0x5b returned 0 after 5 usecs
[ 5.540371] calling esp6_init+0x0/0x5b @ 1
[ 5.540371] initcall esp6_init+0x0/0x5b returned 0 after 1 usecs
[ 5.540371] calling ipcomp6_init+0x0/0x5b @ 1
[ 5.540371] initcall ipcomp6_init+0x0/0x5b returned 0 after 2 usecs
[ 5.540371] calling xfrm6_tunnel_init+0x0/0xb6 @ 1
[ 5.540371] initcall xfrm6_tunnel_init+0x0/0xb6 returned 0 after 287 usecs
[ 5.540371] calling tunnel6_init+0x0/0x5b @ 1
[ 5.540371] initcall tunnel6_init+0x0/0x5b returned 0 after 1 usecs
[ 5.540371] calling xfrm6_transport_init+0x0/0xf @ 1
[ 5.540371] initcall xfrm6_transport_init+0x0/0xf returned 0 after 1 usecs
[ 5.540371] calling xfrm6_mode_tunnel_init+0x0/0xf @ 1
[ 5.540371] initcall xfrm6_mode_tunnel_init+0x0/0xf returned 0 after 1 usecs
[ 5.540371] calling xfrm6_ro_init+0x0/0xf @ 1
[ 5.540371] initcall xfrm6_ro_init+0x0/0xf returned 0 after 1 usecs
[ 5.540371] calling xfrm6_beet_init+0x0/0xf @ 1
[ 5.540371] initcall xfrm6_beet_init+0x0/0xf returned 0 after 1 usecs
[ 5.540371] calling mip6_init+0x0/0xa2 @ 1
[ 5.540371] Mobile IPv6
[ 5.540371] initcall mip6_init+0x0/0xa2 returned 0 after 182 usecs
[ 5.540371] calling ip6_tables_init+0x0/0x86 @ 1
[ 5.540371] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 5.540371] initcall ip6_tables_init+0x0/0x86 returned 0 after 297 usecs
[ 5.540371] calling ip6table_filter_init+0x0/0x57 @ 1
[ 5.540371] initcall ip6table_filter_init+0x0/0x57 returned 0 after 118 usecs
[ 5.540371] calling ip6table_mangle_init+0x0/0x3c @ 1
[ 5.549552] initcall ip6table_mangle_init+0x0/0x3c returned 0 after 442 usecs
[ 5.549788] calling ip6_queue_init+0x0/0x104 @ 1
[ 5.550150] initcall ip6_queue_init+0x0/0x104 returned 0 after 147 usecs
[ 5.550186] calling ip6table_raw_init+0x0/0x3c @ 1
[ 5.550186] initcall ip6table_raw_init+0x0/0x3c returned 0 after 67 usecs
[ 5.550186] calling nf_conntrack_l3proto_ipv6_init+0x0/0xce @ 1
[ 5.550186] initcall nf_conntrack_l3proto_ipv6_init+0x0/0xce returned 0 after 32 usecs
[ 5.550186] calling nf_defrag_init+0x0/0x42 @ 1
[ 5.550186] initcall nf_defrag_init+0x0/0x42 returned 0 after 25 usecs
[ 5.550186] calling ah_mt6_init+0x0/0xa @ 1
[ 5.550186] initcall ah_mt6_init+0x0/0xa returned 0 after 1 usecs
[ 5.550186] calling eui64_mt6_init+0x0/0xa @ 1
[ 5.550186] initcall eui64_mt6_init+0x0/0xa returned 0 after 1 usecs
[ 5.550186] calling frag_mt6_init+0x0/0xa @ 1
[ 5.550186] initcall frag_mt6_init+0x0/0xa returned 0 after 1 usecs
[ 5.550186] calling ipv6header_mt6_init+0x0/0xa @ 1
[ 5.550186] initcall ipv6header_mt6_init+0x0/0xa returned 0 after 1 usecs
[ 5.550186] calling mh_mt6_init+0x0/0xa @ 1
[ 5.550186] initcall mh_mt6_init+0x0/0xa returned 0 after 1 usecs
[ 5.550186] calling hbh_mt6_init+0x0/0xf @ 1
[ 5.550186] initcall hbh_mt6_init+0x0/0xf returned 0 after 1 usecs
[ 5.550186] calling rt_mt6_init+0x0/0xa @ 1
[ 5.550186] initcall rt_mt6_init+0x0/0xa returned 0 after 1 usecs
[ 5.550186] calling log_tg6_init+0x0/0x20 @ 1
[ 5.550186] initcall log_tg6_init+0x0/0x20 returned 0 after 3 usecs
[ 5.550186] calling reject_tg6_init+0x0/0xa @ 1
[ 5.550186] initcall reject_tg6_init+0x0/0xa returned 0 after 1 usecs
[ 5.550186] calling sit_init+0x0/0x4a @ 1
[ 5.550186] IPv6 over IPv4 tunneling driver
[ 5.560187] initcall sit_init+0x0/0x4a returned 0 after 3122 usecs
[ 5.560187] calling ip6_tunnel_init+0x0/0x74 @ 1
[ 5.560187] initcall ip6_tunnel_init+0x0/0x74 returned 0 after 2263 usecs
[ 5.560187] calling packet_init+0x0/0x35 @ 1
[ 5.560187] NET: Registered protocol family 17
[ 5.560187] initcall packet_init+0x0/0x35 returned 0 after 272 usecs
[ 5.560187] calling br_init+0x0/0x97 @ 1
[ 5.560187] Bridge firewalling registered
[ 5.560187] initcall br_init+0x0/0x97 returned 0 after 593 usecs
[ 5.560187] calling ebtables_init+0x0/0x3e @ 1
[ 5.560187] Ebtables v2.0 registered
[ 5.560187] initcall ebtables_init+0x0/0x3e returned 0 after 186 usecs
[ 5.560187] calling ebtable_broute_init+0x0/0x1b @ 1
[ 5.560187] initcall ebtable_broute_init+0x0/0x1b returned 0 after 118 usecs
[ 5.560187] calling ebtable_filter_init+0x0/0x34 @ 1
[ 5.560187] initcall ebtable_filter_init+0x0/0x34 returned 0 after 61 usecs
[ 5.560187] calling ebtable_nat_init+0x0/0x34 @ 1
[ 5.560187] initcall ebtable_nat_init+0x0/0x34 returned 0 after 76 usecs
[ 5.560187] calling ebt_802_3_init+0x0/0xa @ 1
[ 5.560187] initcall ebt_802_3_init+0x0/0xa returned 0 after 1 usecs
[ 5.560187] calling ebt_among_init+0x0/0xa @ 1
[ 5.560187] initcall ebt_among_init+0x0/0xa returned 0 after 1 usecs
[ 5.560187] calling ebt_arp_init+0x0/0xa @ 1
[ 5.560187] initcall ebt_arp_init+0x0/0xa returned 0 after 1 usecs
[ 5.560187] calling ebt_ip_init+0x0/0xa @ 1
[ 5.560187] initcall ebt_ip_init+0x0/0xa returned 0 after 1 usecs
[ 5.560187] calling ebt_ip6_init+0x0/0xa @ 1
[ 5.560187] initcall ebt_ip6_init+0x0/0xa returned 0 after 1 usecs
[ 5.560187] calling ebt_limit_init+0x0/0xa @ 1
[ 5.560187] initcall ebt_limit_init+0x0/0xa returned 0 after 1 usecs
[ 5.560187] calling ebt_mark_m_init+0x0/0xa @ 1
[ 5.560187] initcall ebt_mark_m_init+0x0/0xa returned 0 after 1 usecs
[ 5.560187] calling ebt_pkttype_init+0x0/0xa @ 1
[ 5.560187] initcall ebt_pkttype_init+0x0/0xa returned 0 after 1 usecs
[ 5.560187] calling ebt_stp_init+0x0/0xa @ 1
[ 5.560187] initcall ebt_stp_init+0x0/0xa returned 0 after 1 usecs
[ 5.560187] calling ebt_vlan_init+0x0/0xa @ 1
[ 5.560187] initcall ebt_vlan_init+0x0/0xa returned 0 after 1 usecs
[ 5.560187] calling ebt_arpreply_init+0x0/0xa @ 1
[ 5.560187] initcall ebt_arpreply_init+0x0/0xa returned 0 after 1 usecs
[ 5.560187] calling ebt_mark_init+0x0/0xa @ 1
[ 5.560187] initcall ebt_mark_init+0x0/0xa returned 0 after 1 usecs
[ 5.560187] calling ebt_dnat_init+0x0/0xa @ 1
[ 5.560187] initcall ebt_dnat_init+0x0/0xa returned 0 after 1 usecs
[ 5.560187] calling ebt_redirect_init+0x0/0xa @ 1
[ 5.560187] initcall ebt_redirect_init+0x0/0xa returned 0 after 1 usecs
[ 5.560187] calling ebt_snat_init+0x0/0xa @ 1
[ 5.560187] initcall ebt_snat_init+0x0/0xa returned 0 after 1 usecs
[ 5.560187] calling ebt_log_init+0x0/0x20 @ 1
[ 5.560187] initcall ebt_log_init+0x0/0x20 returned 0 after 5 usecs
[ 5.560187] calling ebt_ulog_init+0x0/0xac @ 1
[ 5.575843] initcall ebt_ulog_init+0x0/0xac returned -12 after 293 usecs
[ 5.576073] initcall ebt_ulog_init+0x0/0xac returned with error code -12
[ 5.576282] calling ebt_nflog_init+0x0/0xa @ 1
[ 5.576483] initcall ebt_nflog_init+0x0/0xa returned 0 after 2 usecs
[ 5.576641] calling vlan_proto_init+0x0/0x79 @ 1
[ 5.576641] 802.1Q VLAN Support v1.8
[ 5.576641] initcall vlan_proto_init+0x0/0x79 returned 0 after 293 usecs
[ 5.576641] calling sctp_init+0x0/0x6e3 @ 1
[ 5.579730] sctp: Hash tables configured (established 16384 bind 16384)
[ 5.580307] initcall sctp_init+0x0/0x6e3 returned 0 after 4842 usecs
[ 5.580307] calling lib80211_init+0x0/0x15 @ 1
[ 5.580307] lib80211: common routines for IEEE802.11 drivers
[ 5.580307] lib80211_crypt: registered algorithm 'NULL'
[ 5.580307] initcall lib80211_init+0x0/0x15 returned 0 after 390 usecs
[ 5.580307] calling hpet_insert_resource+0x0/0x1a @ 1
[ 5.580307] initcall hpet_insert_resource+0x0/0x1a returned 1 after 1 usecs
[ 5.580307] initcall hpet_insert_resource+0x0/0x1a returned with error code 1
[ 5.580307] calling update_mp_table+0x0/0x484 @ 1
[ 5.580307] initcall update_mp_table+0x0/0x484 returned 0 after 1 usecs
[ 5.580307] calling lapic_insert_resource+0x0/0x41 @ 1
[ 5.580307] initcall lapic_insert_resource+0x0/0x41 returned -1 after 1 usecs
[ 5.580307] initcall lapic_insert_resource+0x0/0x41 returned with error code -1
[ 5.580307] calling io_apic_bug_finalize+0x0/0x16 @ 1
[ 5.580307] initcall io_apic_bug_finalize+0x0/0x16 returned 0 after 0 usecs
[ 5.580307] calling print_ipi_mode+0x0/0x24 @ 1
[ 5.580307] Using IPI No-Shortcut mode
[ 5.580307] initcall print_ipi_mode+0x0/0x24 returned 0 after 188 usecs
[ 5.580307] calling check_early_ioremap_leak+0x0/0x58 @ 1
[ 5.580307] initcall check_early_ioremap_leak+0x0/0x58 returned 0 after 1 usecs
[ 5.580307] calling init_oops_id+0x0/0x36 @ 1
[ 5.580307] initcall init_oops_id+0x0/0x36 returned 0 after 0 usecs
[ 5.580307] calling printk_late_init+0x0/0x3e @ 1
[ 5.580307] initcall printk_late_init+0x0/0x3e returned 0 after 7 usecs
[ 5.580307] calling pm_qos_power_init+0x0/0x4e @ 1
[ 5.590181] initcall pm_qos_power_init+0x0/0x4e returned 0 after 2261 usecs
[ 5.590181] calling alarmtimer_init_late+0x0/0x59 @ 1
[ 5.590181] initcall alarmtimer_init_late+0x0/0x59 returned 0 after 10 usecs
[ 5.590181] calling taskstats_init+0x0/0x76 @ 1
[ 5.590181] registered taskstats version 1
[ 5.590181] initcall taskstats_init+0x0/0x76 returned 0 after 228 usecs
[ 5.590181] calling max_swapfiles_check+0x0/0x3 @ 1
[ 5.590181] initcall max_swapfiles_check+0x0/0x3 returned 0 after 1 usecs
[ 5.590181] calling random32_reseed+0x0/0x84 @ 1
[ 5.590181] initcall random32_reseed+0x0/0x84 returned 0 after 37 usecs
[ 5.590181] calling pci_resource_alignment_sysfs_init+0x0/0xf @ 1
[ 5.590181] initcall pci_resource_alignment_sysfs_init+0x0/0xf returned 0 after 22 usecs
[ 5.590181] calling pci_sysfs_init+0x0/0x40 @ 1
[ 5.590181] initcall pci_sysfs_init+0x0/0x40 returned 0 after 795 usecs
[ 5.590181] calling boot_wait_for_devices+0x0/0x2b @ 1
[ 5.590181] initcall boot_wait_for_devices+0x0/0x2b returned 0 after 4 usecs
[ 5.590181] calling seqgen_init+0x0/0xa @ 1
[ 5.590181] initcall seqgen_init+0x0/0xa returned 0 after 74 usecs
[ 5.590181] calling scsi_complete_async_scans+0x0/0xed @ 1
[ 5.590181] initcall scsi_complete_async_scans+0x0/0xed returned 0 after 1 usecs
[ 5.590181] calling powernowk8_init+0x0/0x153 @ 1
[ 5.590181] initcall powernowk8_init+0x0/0x153 returned -19 after 6 usecs
[ 5.590181] calling acpi_cpufreq_init+0x0/0x9c @ 1
[ 5.590181] initcall acpi_cpufreq_init+0x0/0x9c returned -5 after 107 usecs
[ 5.590181] initcall acpi_cpufreq_init+0x0/0x9c returned with error code -5
[ 5.590181] calling powernow_init+0x0/0x117 @ 1
[ 5.590181] initcall powernow_init+0x0/0x117 returned -19 after 0 usecs
[ 5.590181] calling cpufreq_p4_init+0x0/0x4d @ 1
[ 5.590181] initcall cpufreq_p4_init+0x0/0x4d returned -19 after 1 usecs
[ 5.590181] calling edd_init+0x0/0x2d2 @ 1
[ 5.590181] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 5.590181] EDD information not available.
[ 5.590181] initcall edd_init+0x0/0x2d2 returned -19 after 385 usecs
[ 5.590181] calling memmap_init+0x0/0x22 @ 1
[ 5.590181] initcall memmap_init+0x0/0x22 returned 0 after 99 usecs
[ 5.590181] calling pci_mmcfg_late_insert_resources+0x0/0x4f @ 1
[ 5.590181] initcall pci_mmcfg_late_insert_resources+0x0/0x4f returned 1 after 1 usecs
[ 5.590181] initcall pci_mmcfg_late_insert_resources+0x0/0x4f returned with error code 1
[ 5.590181] calling tcp_congestion_default+0x0/0xa @ 1
[ 5.590181] initcall tcp_congestion_default+0x0/0xa returned 0 after 5 usecs
[ 5.590181] calling initialize_hashrnd+0x0/0x12 @ 1
[ 5.590181] initcall initialize_hashrnd+0x0/0x12 returned 0 after 17 usecs
[ 5.601612] async_waiting @ 1
[ 5.601834] async_continuing @ 1 after 2 usec
[ 5.602143] Freeing unused kernel memory: 716k freed
[ 6.860196] udevd (2319): /proc/2319/oom_adj is deprecated, please use /proc/2319/oom_score_adj instead.
[ 12.840240] EXT3-fs: barriers not enabled
[ 12.850306] kjournald starting. Commit interval 5 seconds
[ 12.850306] EXT3-fs (sda1): mounted filesystem with writeback data mode
[ 13.225078] EXT3-fs: barriers not enabled
[ 13.225078] kjournald starting. Commit interval 5 seconds
[ 13.225078] EXT3-fs (sda1): mounted filesystem with writeback data mode
[ 23.320496] udev: starting version 151
[ 30.913907] EXT3-fs: barriers not enabled
[ 30.914718] kjournald starting. Commit interval 5 seconds
[ 30.915783] EXT3-fs (dm-0): using internal journal
[ 30.915819] EXT3-fs (dm-0): mounted filesystem with writeback data mode
[ 34.090576] XENBUS: Unable to read cpu state
[ 47.370841] ADDRCONF(NETDEV_UP): br-local: link is not ready
[ 47.550839] ADDRCONF(NETDEV_UP): br-internal: link is not ready
[ 47.780865] device peth0 entered promiscuous mode
[ 47.800871] peth0: setting full-duplex.
[ 47.800871] br-local: port 1(peth0) entering forwarding state
[ 47.800871] br-local: port 1(peth0) entering forwarding state
[ 47.800871] ADDRCONF(NETDEV_CHANGE): br-local: link becomes ready
[ 56.840080] peth0: no IPv6 routers present
[ 57.930026] br-local: no IPv6 routers present
[ 74.991033] device vif1.0 entered promiscuous mode
[ 75.061323] ADDRCONF(NETDEV_UP): vif1.0: link is not ready
[ 84.574398] xen-blkback:ring-ref 10, event-channel 10, protocol 1 (x86_32-abi)
[ 84.631573] xen-blkback:ring-ref 11, event-channel 11, protocol 1 (x86_32-abi)
[ 84.801512] ADDRCONF(NETDEV_CHANGE): vif1.0: link becomes ready
[ 84.801512] br-internal: port 1(vif1.0) entering forwarding state
[ 84.801512] br-internal: port 1(vif1.0) entering forwarding state
[ 84.801512] ADDRCONF(NETDEV_CHANGE): br-internal: link becomes ready
[ 95.220631] vif1.0: no IPv6 routers present
[ 95.220658] br-internal: no IPv6 routers present
[ 98.641597] device vif2.0 entered promiscuous mode
[ 98.791623] ADDRCONF(NETDEV_UP): vif2.0: link is not ready
[-- Attachment #3: Type: text/plain, Size: 138 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 5x dom0 memory increase from Xen/Linux 3.4/2.6.18 to 4.1/3.0.0
2011-06-22 13:15 ` Anthony Wright
@ 2011-06-22 13:32 ` Konrad Rzeszutek Wilk
2011-06-22 14:22 ` Anthony Wright
0 siblings, 1 reply; 10+ messages in thread
From: Konrad Rzeszutek Wilk @ 2011-06-22 13:32 UTC (permalink / raw)
To: Anthony Wright; +Cc: xen-devel
On Wed, Jun 22, 2011 at 02:15:35PM +0100, Anthony Wright wrote:
> On 20/06/2011 13:45, Konrad Rzeszutek Wilk wrote:
> > On Fri, Jun 17, 2011 at 04:31:11PM +0100, Anthony Wright wrote:
> >> Lowering swiotlb helped, and got me down to 200M for dom0. What is the effect of reducing this value?
> > Less amount of bounce buffer. But you don't need the bounce buffer for PCI devices b/c you don't
> > have more than 4GB of physical memory in the machine.
> Do I only need bounce buffers if I have > 4GB of physical memory? In
Correct.
> this case should I allocate the 64M, or is it a sliding memory requirement?
It really is unknown. At some point the maintainer was thinking of adding
dynamic code so that it would increase as neccessary - but it never got
further than: "this would be neat". I would say try some small numbers
and when the machine is on full load it panics (or gives you a nasty
kernel message).
> >> I set CONFIG_XEN_MAX_DOMAIN_MEMORY down to 8, but that didn't seem to have any effect on dom0's memory requirement. What is this value? Does it only apply to a domU's memory usage?
> > It makes some internal datastructures (P2M) smaller. They are set up for 128GB or so machines initially.
> It sounds like this value applies to DomUs, does this config variables
> set the maximum amount of memory 128GB per DomU or across all DomUs,
> i.e. if I have 16 DomUs and a CONFIG_XEN_MAX_DOMAIN_MEMORY of 16, do
> they each have a maximum of 16GB, or do the get 1GB each?
I mistyped this. The internal datastructures just set the limits to what
they can go to. But they don't consume any real RAM - just virtual addresses
and during boot time that gets resolved (shrunk appropiately). So don't worry about it.
> >> I tried the memblock=debug options, and while I got lots of output, I could see very little on the subject of memory usage.
> > The numbers are what amount of memory is reserved. You can find out which are are is eating the most
> > by computing the difference.
> Maybe I'm misreading the output, but I couldn't see any numbers that
> look like memory being assigned. I've attached the dmesg output. Do I
> need to enable a CONFIG variable to get the output I need or am I
> missing something.
The memblock=debug should give you some idea of what is Reserved. The
Reserved includes memory that is allocated by boot-time services (P2M,
pagetables, NUMA) and by real reservations (for example ACPI space).
Using the 'memblock=debug' can give you an idea of what services are
reserving the most. Then we can narrow down who or what is eating the gobs
of memory.
see the 'Memory: ".. numbers. Also you might want to eliminate
the balloon usage space algother by doing two things:
Xen command line: dom0_mem=max:512MB
Linux command line: mem=512MB
That will effectivly remove any balloon space (so your Dom0 will _never_
grow up).
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 5x dom0 memory increase from Xen/Linux 3.4/2.6.18 to 4.1/3.0.0
2011-06-22 13:32 ` Konrad Rzeszutek Wilk
@ 2011-06-22 14:22 ` Anthony Wright
2011-06-22 14:39 ` Konrad Rzeszutek Wilk
0 siblings, 1 reply; 10+ messages in thread
From: Anthony Wright @ 2011-06-22 14:22 UTC (permalink / raw)
To: Konrad Rzeszutek Wilk; +Cc: xen-devel
On 22/06/2011 14:32, Konrad Rzeszutek Wilk wrote:
> On Wed, Jun 22, 2011 at 02:15:35PM +0100, Anthony Wright wrote:
>> Maybe I'm misreading the output, but I couldn't see any numbers that
>> look like memory being assigned. I've attached the dmesg output. Do I
>> need to enable a CONFIG variable to get the output I need or am I
>> missing something.
> The memblock=debug should give you some idea of what is Reserved. The
> Reserved includes memory that is allocated by boot-time services (P2M,
> pagetables, NUMA) and by real reservations (for example ACPI space).
> Using the 'memblock=debug' can give you an idea of what services are
> reserving the most. Then we can narrow down who or what is eating the gobs
> of memory.
>
> see the 'Memory: ".. numbers. Also you might want to eliminate
> the balloon usage space algother by doing two things:
>
> Xen command line: dom0_mem=max:512MB
>
> Linux command line: mem=512MB
>
> That will effectivly remove any balloon space (so your Dom0 will _never_
> grow up).
The problem is I can't see any lines in the kernel dmesg output
(attached to previous email) that start "Memory: ", or anything else
that looks hopeful. Is there anything else I should add to the command
line, is there a kernel CONFIG option I should turn on or am I missing
something else?
thanks,
Anthony.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 5x dom0 memory increase from Xen/Linux 3.4/2.6.18 to 4.1/3.0.0
2011-06-22 14:22 ` Anthony Wright
@ 2011-06-22 14:39 ` Konrad Rzeszutek Wilk
2011-06-22 15:53 ` Anthony Wright
0 siblings, 1 reply; 10+ messages in thread
From: Konrad Rzeszutek Wilk @ 2011-06-22 14:39 UTC (permalink / raw)
To: Anthony Wright; +Cc: xen-devel
On Wed, Jun 22, 2011 at 03:22:30PM +0100, Anthony Wright wrote:
> On 22/06/2011 14:32, Konrad Rzeszutek Wilk wrote:
> > On Wed, Jun 22, 2011 at 02:15:35PM +0100, Anthony Wright wrote:
> >> Maybe I'm misreading the output, but I couldn't see any numbers that
> >> look like memory being assigned. I've attached the dmesg output. Do I
> >> need to enable a CONFIG variable to get the output I need or am I
> >> missing something.
> > The memblock=debug should give you some idea of what is Reserved. The
> > Reserved includes memory that is allocated by boot-time services (P2M,
> > pagetables, NUMA) and by real reservations (for example ACPI space).
> > Using the 'memblock=debug' can give you an idea of what services are
> > reserving the most. Then we can narrow down who or what is eating the gobs
> > of memory.
> >
> > see the 'Memory: ".. numbers. Also you might want to eliminate
> > the balloon usage space algother by doing two things:
> >
> > Xen command line: dom0_mem=max:512MB
> >
> > Linux command line: mem=512MB
> >
> > That will effectivly remove any balloon space (so your Dom0 will _never_
> > grow up).
> The problem is I can't see any lines in the kernel dmesg output
> (attached to previous email) that start "Memory: ", or anything else
> that looks hopeful. Is there anything else I should add to the command
dmesg | grep Memory: ?
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 5x dom0 memory increase from Xen/Linux 3.4/2.6.18 to 4.1/3.0.0
2011-06-22 14:39 ` Konrad Rzeszutek Wilk
@ 2011-06-22 15:53 ` Anthony Wright
2011-06-23 13:02 ` Konrad Rzeszutek Wilk
0 siblings, 1 reply; 10+ messages in thread
From: Anthony Wright @ 2011-06-22 15:53 UTC (permalink / raw)
To: Konrad Rzeszutek Wilk; +Cc: xen-devel
On 22/06/2011 15:39, Konrad Rzeszutek Wilk wrote:
> On Wed, Jun 22, 2011 at 03:22:30PM +0100, Anthony Wright wrote:
>> On 22/06/2011 14:32, Konrad Rzeszutek Wilk wrote:
>>> On Wed, Jun 22, 2011 at 02:15:35PM +0100, Anthony Wright wrote:
>>>> Maybe I'm misreading the output, but I couldn't see any numbers that
>>>> look like memory being assigned. I've attached the dmesg output. Do I
>>>> need to enable a CONFIG variable to get the output I need or am I
>>>> missing something.
>>> The memblock=debug should give you some idea of what is Reserved. The
>>> Reserved includes memory that is allocated by boot-time services (P2M,
>>> pagetables, NUMA) and by real reservations (for example ACPI space).
>>> Using the 'memblock=debug' can give you an idea of what services are
>>> reserving the most. Then we can narrow down who or what is eating the gobs
>>> of memory.
>>>
>>> see the 'Memory: ".. numbers. Also you might want to eliminate
>>> the balloon usage space algother by doing two things:
>>>
>>> Xen command line: dom0_mem=max:512MB
>>>
>>> Linux command line: mem=512MB
>>>
>>> That will effectivly remove any balloon space (so your Dom0 will _never_
>>> grow up).
>> The problem is I can't see any lines in the kernel dmesg output
>> (attached to previous email) that start "Memory: ", or anything else
>> that looks hopeful. Is there anything else I should add to the command
> dmesg | grep Memory: ?
Ok, I'm being really thick here, but I can't get the Memory: lines to be
output by the kernel. It looks like I can't get any KERN_INFO or
KERN_DEBUG lines to be output no matter what I do to log level. I'm not
much of a kernel hacker, but is there some debug code that I need to
enable to get these messages? I've wandered through google, and the
kernel code but I can't find anything obvious.
thanks,
Anthony.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 5x dom0 memory increase from Xen/Linux 3.4/2.6.18 to 4.1/3.0.0
2011-06-22 15:53 ` Anthony Wright
@ 2011-06-23 13:02 ` Konrad Rzeszutek Wilk
0 siblings, 0 replies; 10+ messages in thread
From: Konrad Rzeszutek Wilk @ 2011-06-23 13:02 UTC (permalink / raw)
To: Anthony Wright; +Cc: xen-devel
On Wed, Jun 22, 2011 at 04:53:40PM +0100, Anthony Wright wrote:
> On 22/06/2011 15:39, Konrad Rzeszutek Wilk wrote:
> > On Wed, Jun 22, 2011 at 03:22:30PM +0100, Anthony Wright wrote:
> >> On 22/06/2011 14:32, Konrad Rzeszutek Wilk wrote:
> >>> On Wed, Jun 22, 2011 at 02:15:35PM +0100, Anthony Wright wrote:
> >>>> Maybe I'm misreading the output, but I couldn't see any numbers that
> >>>> look like memory being assigned. I've attached the dmesg output. Do I
> >>>> need to enable a CONFIG variable to get the output I need or am I
> >>>> missing something.
> >>> The memblock=debug should give you some idea of what is Reserved. The
> >>> Reserved includes memory that is allocated by boot-time services (P2M,
> >>> pagetables, NUMA) and by real reservations (for example ACPI space).
> >>> Using the 'memblock=debug' can give you an idea of what services are
> >>> reserving the most. Then we can narrow down who or what is eating the gobs
> >>> of memory.
> >>>
> >>> see the 'Memory: ".. numbers. Also you might want to eliminate
> >>> the balloon usage space algother by doing two things:
> >>>
> >>> Xen command line: dom0_mem=max:512MB
> >>>
> >>> Linux command line: mem=512MB
> >>>
> >>> That will effectivly remove any balloon space (so your Dom0 will _never_
> >>> grow up).
> >> The problem is I can't see any lines in the kernel dmesg output
> >> (attached to previous email) that start "Memory: ", or anything else
> >> that looks hopeful. Is there anything else I should add to the command
> > dmesg | grep Memory: ?
> Ok, I'm being really thick here, but I can't get the Memory: lines to be
> output by the kernel. It looks like I can't get any KERN_INFO or
> KERN_DEBUG lines to be output no matter what I do to log level. I'm not
> much of a kernel hacker, but is there some debug code that I need to
> enable to get these messages? I've wandered through google, and the
> kernel code but I can't find anything obvious.
'debug loglevel=10' ?
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2011-06-23 13:02 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2011-06-16 12:58 5x dom0 memory increase from Xen/Linux 3.4/2.6.18 to 4.1/3.0.0 Anthony Wright
2011-06-16 14:56 ` Konrad Rzeszutek Wilk
2011-06-17 15:31 ` Anthony Wright
2011-06-20 12:45 ` Konrad Rzeszutek Wilk
2011-06-22 13:15 ` Anthony Wright
2011-06-22 13:32 ` Konrad Rzeszutek Wilk
2011-06-22 14:22 ` Anthony Wright
2011-06-22 14:39 ` Konrad Rzeszutek Wilk
2011-06-22 15:53 ` Anthony Wright
2011-06-23 13:02 ` Konrad Rzeszutek Wilk
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.