* re: [media] tda10071: NXP TDA10071 DVB-S/S2 driver
@ 2012-04-17 10:33 Dan Carpenter
2012-04-17 11:19 ` Antti Palosaari
2012-07-01 18:34 ` Antti Palosaari
0 siblings, 2 replies; 3+ messages in thread
From: Dan Carpenter @ 2012-04-17 10:33 UTC (permalink / raw)
To: crope; +Cc: linux-media
Hi Antti,
Smatch complains about a potential information leak. I was hoping you
could take a look.
The patch de8e42035014: "[media] tda10071: NXP TDA10071 DVB-S/S2
driver" from Aug 1, 2011, leads to the following warning:
drivers/media/dvb/frontends/tda10071.c:322
tda10071_diseqc_send_master_cmd()
error: memcpy() 'diseqc_cmd->msg' too small (6 vs 16)
drivers/media/dvb/frontends/tda10071.c
290 if (diseqc_cmd->msg_len < 3 || diseqc_cmd->msg_len > 16) {
^^^^^^^^^^^^^^^^^^^^^^^^
We cap ->msg_len at 16 here. I wasn't able to figure out where the 16
came from. Or the 3 for that matter.
291 ret = -EINVAL;
292 goto error;
293 }
294
295 /* wait LNB TX */
296 for (i = 500, tmp = 0; i && !tmp; i--) {
297 ret = tda10071_rd_reg_mask(priv, 0x47, &tmp, 0x01);
298 if (ret)
299 goto error;
300
301 usleep_range(10000, 20000);
302 }
303
304 dbg("%s: loop=%d", __func__, i);
305
306 if (i == 0) {
307 ret = -ETIMEDOUT;
308 goto error;
309 }
310
311 ret = tda10071_wr_reg_mask(priv, 0x47, 0x00, 0x01);
312 if (ret)
313 goto error;
314
315 cmd.args[0x00] = CMD_LNB_SEND_DISEQC;
316 cmd.args[0x01] = 0;
317 cmd.args[0x02] = 0;
318 cmd.args[0x03] = 0;
319 cmd.args[0x04] = 2;
320 cmd.args[0x05] = 0;
321 cmd.args[0x06] = diseqc_cmd->msg_len;
322 memcpy(&cmd.args[0x07], diseqc_cmd->msg, diseqc_cmd->msg_len);
^^^^^^^^^^^^^^^
->msg is only 6 bytes long so we're copying past the end of the array.
Also cmd.arg is 0x1e (30) bytes long and we only copy 0x07 + 16 bytes
into it so it leaves the last 7 bytes of cmd.args unitialized. Btw,
why are the sizes specified in hex instead of decimal here?
323 cmd.len = 0x07 + diseqc_cmd->msg_len;
regards,
dan carpenter
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [media] tda10071: NXP TDA10071 DVB-S/S2 driver
2012-04-17 10:33 [media] tda10071: NXP TDA10071 DVB-S/S2 driver Dan Carpenter
@ 2012-04-17 11:19 ` Antti Palosaari
2012-07-01 18:34 ` Antti Palosaari
1 sibling, 0 replies; 3+ messages in thread
From: Antti Palosaari @ 2012-04-17 11:19 UTC (permalink / raw)
To: Dan Carpenter; +Cc: linux-media
Moikka Dan,
and thank you. Comments below.
On 17.04.2012 13:33, Dan Carpenter wrote:
> Hi Antti,
>
> Smatch complains about a potential information leak. I was hoping you
> could take a look.
>
> The patch de8e42035014: "[media] tda10071: NXP TDA10071 DVB-S/S2
> driver" from Aug 1, 2011, leads to the following warning:
> drivers/media/dvb/frontends/tda10071.c:322
> tda10071_diseqc_send_master_cmd()
> error: memcpy() 'diseqc_cmd->msg' too small (6 vs 16)
>
>
> drivers/media/dvb/frontends/tda10071.c
> 290 if (diseqc_cmd->msg_len< 3 || diseqc_cmd->msg_len> 16) {
> ^^^^^^^^^^^^^^^^^^^^^^^^
> We cap ->msg_len at 16 here. I wasn't able to figure out where the 16
> came from. Or the 3 for that matter.
Those numbers are coming from include/linux/dvb/frontend.h struct
dvb_diseqc_master_cmd. And initially values are from the DiSEqC spec.
But you are correct, it is bug. Upper limit for message len should be 6
instead of 16 used currently. Likely just typo. Maybe I have done some
len testing during the development and changed it temporarily 6 => 16
and forgot switch back. Who knows...
>
> 291 ret = -EINVAL;
> 292 goto error;
> 293 }
> 294
> 295 /* wait LNB TX */
> 296 for (i = 500, tmp = 0; i&& !tmp; i--) {
> 297 ret = tda10071_rd_reg_mask(priv, 0x47,&tmp, 0x01);
> 298 if (ret)
> 299 goto error;
> 300
> 301 usleep_range(10000, 20000);
> 302 }
> 303
> 304 dbg("%s: loop=%d", __func__, i);
> 305
> 306 if (i == 0) {
> 307 ret = -ETIMEDOUT;
> 308 goto error;
> 309 }
> 310
> 311 ret = tda10071_wr_reg_mask(priv, 0x47, 0x00, 0x01);
> 312 if (ret)
> 313 goto error;
> 314
> 315 cmd.args[0x00] = CMD_LNB_SEND_DISEQC;
> 316 cmd.args[0x01] = 0;
> 317 cmd.args[0x02] = 0;
> 318 cmd.args[0x03] = 0;
> 319 cmd.args[0x04] = 2;
> 320 cmd.args[0x05] = 0;
> 321 cmd.args[0x06] = diseqc_cmd->msg_len;
> 322 memcpy(&cmd.args[0x07], diseqc_cmd->msg, diseqc_cmd->msg_len);
> ^^^^^^^^^^^^^^^
> ->msg is only 6 bytes long so we're copying past the end of the array.
>
> Also cmd.arg is 0x1e (30) bytes long and we only copy 0x07 + 16 bytes
> into it so it leaves the last 7 bytes of cmd.args unitialized. Btw,
> why are the sizes specified in hex instead of decimal here?
>
> 323 cmd.len = 0x07 + diseqc_cmd->msg_len;
What it happens now is that garbage data will be send to DiSEqC switch -
in case of garbage data is sent from the user-space. Anyhow, I would
like to rather move these kind of common validly checking to the
DVB-core. Not only that case, but for the more commonly too. IMHO there
is currently too general checking left for the individual drivers...
And for the usage of hex numbering - I don't remember. Overall I prefer
hex numbering unless values are not clearly decimal ones, like
frequencies. But I agree indexing like that is seems more readable when
decimal numbering is used. I have generally used decimal numbering in
such cases.
Feel free to sent patch - or I will fix it someday later when suitable
time is found.
thanks,
Antti
-
http://palosaari.fi/
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [media] tda10071: NXP TDA10071 DVB-S/S2 driver
2012-04-17 10:33 [media] tda10071: NXP TDA10071 DVB-S/S2 driver Dan Carpenter
2012-04-17 11:19 ` Antti Palosaari
@ 2012-07-01 18:34 ` Antti Palosaari
1 sibling, 0 replies; 3+ messages in thread
From: Antti Palosaari @ 2012-07-01 18:34 UTC (permalink / raw)
To: Dan Carpenter; +Cc: linux-media
On 04/17/2012 01:33 PM, Dan Carpenter wrote:
> Hi Antti,
>
> Smatch complains about a potential information leak. I was hoping you
> could take a look.
>
> The patch de8e42035014: "[media] tda10071: NXP TDA10071 DVB-S/S2
> driver" from Aug 1, 2011, leads to the following warning:
> drivers/media/dvb/frontends/tda10071.c:322
> tda10071_diseqc_send_master_cmd()
> error: memcpy() 'diseqc_cmd->msg' too small (6 vs 16)
>
>
> drivers/media/dvb/frontends/tda10071.c
> 290 if (diseqc_cmd->msg_len < 3 || diseqc_cmd->msg_len > 16) {
> ^^^^^^^^^^^^^^^^^^^^^^^^
> We cap ->msg_len at 16 here. I wasn't able to figure out where the 16
> came from. Or the 3 for that matter.
>
> 291 ret = -EINVAL;
> 292 goto error;
> 293 }
> 294
> 295 /* wait LNB TX */
> 296 for (i = 500, tmp = 0; i && !tmp; i--) {
> 297 ret = tda10071_rd_reg_mask(priv, 0x47, &tmp, 0x01);
> 298 if (ret)
> 299 goto error;
> 300
> 301 usleep_range(10000, 20000);
> 302 }
> 303
> 304 dbg("%s: loop=%d", __func__, i);
> 305
> 306 if (i == 0) {
> 307 ret = -ETIMEDOUT;
> 308 goto error;
> 309 }
> 310
> 311 ret = tda10071_wr_reg_mask(priv, 0x47, 0x00, 0x01);
> 312 if (ret)
> 313 goto error;
> 314
> 315 cmd.args[0x00] = CMD_LNB_SEND_DISEQC;
> 316 cmd.args[0x01] = 0;
> 317 cmd.args[0x02] = 0;
> 318 cmd.args[0x03] = 0;
> 319 cmd.args[0x04] = 2;
> 320 cmd.args[0x05] = 0;
> 321 cmd.args[0x06] = diseqc_cmd->msg_len;
> 322 memcpy(&cmd.args[0x07], diseqc_cmd->msg, diseqc_cmd->msg_len);
> ^^^^^^^^^^^^^^^
> ->msg is only 6 bytes long so we're copying past the end of the array.
>
> Also cmd.arg is 0x1e (30) bytes long and we only copy 0x07 + 16 bytes
> into it so it leaves the last 7 bytes of cmd.args unitialized. Btw,
> why are the sizes specified in hex instead of decimal here?
>
> 323 cmd.len = 0x07 + diseqc_cmd->msg_len;
>
> regards,
> dan carpenter
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
http://palosaari.fi/
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2012-07-01 18:35 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-04-17 10:33 [media] tda10071: NXP TDA10071 DVB-S/S2 driver Dan Carpenter
2012-04-17 11:19 ` Antti Palosaari
2012-07-01 18:34 ` Antti Palosaari
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.