All of lore.kernel.org
 help / color / mirror / Atom feed
* 3.2.14: Marvell 88SE9123 PCIe SATA 6.0 Gb/s controller not working
@ 2012-04-13 20:26 Martin Mokrejs
  2012-04-14 12:39 ` Mark Lord
  2012-04-22  6:22 ` Robert Hancock
  0 siblings, 2 replies; 4+ messages in thread
From: Martin Mokrejs @ 2012-04-13 20:26 UTC (permalink / raw)
  To: jgarzik, linux-ide

[-- Attachment #1: Type: text/plain, Size: 1526 bytes --]

Hi,
  I am looking for an Express Card to plug into my laptop to provide additional
eSATA port. I just tried two cards, incidentally having same chipset. One was
from Axago ECS-6S (1x eSATA port) and the other was Kouwell EK-113 (2x eSATA).
Both cards have just one/two eSATA ports but kernel tries to assign many ata ports
(see the logs). And this was probably fatal issue:

DRHD: handling fault status reg 2
DMAR:[DMA Read] Request device [11:00.1] fault addr fff00000
DMAR:[fault reason 02] Present bit in context entry is clear

  I have attached three files with lspci and dmesg output. Is this chip supported?
I just tried the cards in a shop and returned immediately, so I cannot re-test
them again unless I buy one of them.

  Should I go rather for one of the Sil3132 eSATA cards from DeLock?


Here are my notes of what is available (in theory):

DeLock 66224: Sil3132, 1x eSATA, SATA I only
DeLock 61957 and 61891: Marvell 88SE9128? 1xeSATA, SATA III
                        Maybe my typo? Is is same chipset like here reported problematic
                        88SE9123?
Looks these also exist:
Axago ECS-SL: JMB360, 1x eSATA, SATA II (JMicron?, I had bad luck with JM20337 and JMS539, no, thanks).
Axago ECS-X1 (probably same is DeLock 61478): Sil3531, 1x eSATA, SATA II

DeLock 61386: Sil3132, 2x eSATA, SATA II, no RAID
DeLock 66221: Sil3132, 2x eSATA, SATA II, with RAID

  I haven't anywhewre the Sil chip based cards yet to try. Is it worth the effort?
Which would you suggest?
Thank you very much,
Martin

[-- Attachment #2: Axago_ECS-6S.txt --]
[-- Type: text/plain, Size: 55197 bytes --]

# lspci
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05)
00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05)
00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5)
00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5)
00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5)
00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b5)
00:1c.7 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 (rev b5)
00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05)
00:1f.0 ISA bridge: Intel Corporation HM67 Express Chipset Family LPC Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05)
00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05)
05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
09:00.0 Network controller: Intel Corporation Centrino Wireless-N 1030 (rev 34)
0b:00.0 USB controller: Texas Instruments Device 8241 (rev 02)
11:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9123 PCIe SATA 6.0 Gb/s controller (rev 11)
#

# lspci -vvx
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
	Subsystem: Dell Device 04b3
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: [e0] Vendor Specific Information: Len=0c <?>
	Kernel driver in use: agpgart-intel
00: 86 80 04 01 06 00 90 20 09 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00

00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller])
	Subsystem: Dell Device 04b3
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 43
	Region 0: Memory at f6800000 (64-bit, non-prefetchable) [size=4M]
	Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
	Region 4: I/O ports at f000 [size=64]
	Expansion ROM at <unassigned> [disabled]
	Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee00018  Data: 0000
	Capabilities: [d0] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [a4] PCI Advanced Features
		AFCap: TP+ FLR+
		AFCtrl: FLR-
		AFStatus: TP-
	Kernel driver in use: i915
00: 86 80 26 01 07 04 90 00 09 00 00 03 00 00 00 00
10: 04 00 80 f6 00 00 00 00 0c 00 00 e0 00 00 00 00
20: 01 f0 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 90 00 00 00 00 00 00 00 0b 01 00 00

00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)
	Subsystem: Dell Device 04b3
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 51
	Region 0: Memory at f7f0a000 (64-bit, non-prefetchable) [size=16]
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+
		Address: 00000000fee00378  Data: 0000
	Kernel driver in use: mei
00: 86 80 3a 1c 06 04 10 00 04 00 80 07 00 00 80 00
10: 04 a0 f0 f7 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 00 00

00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) (prog-if 20 [EHCI])
	Subsystem: Dell Device 04b3
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at f7f08000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Debug port: BAR=1 offset=00a0
	Capabilities: [98] PCI Advanced Features
		AFCap: TP+ FLR+
		AFCtrl: FLR-
		AFStatus: TP-
	Kernel driver in use: ehci_hcd
00: 86 80 2d 1c 06 00 90 02 05 20 03 0c 00 00 00 00
10: 00 80 f0 f7 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 00 00

00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05)
	Subsystem: Dell Device 04b3
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 52
	Region 0: Memory at f7f00000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
		Address: 00000000fee003b8  Data: 0000
	Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- RBE- FLReset+
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
			ClockPM- Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
	Capabilities: [100 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=01
			Status:	NegoPending- InProgress-
		VC1:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=1 ArbSelect=Fixed TC/VC=22
			Status:	NegoPending- InProgress-
	Capabilities: [130 v1] Root Complex Link
		Desc:	PortNumber=0f ComponentID=00 EltType=Config
		Link0:	Desc:	TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+
			Addr:	00000000fed1c000
	Kernel driver in use: snd_hda_intel
00: 86 80 20 1c 06 04 10 00 05 00 03 04 10 00 00 00
10: 04 00 f0 f7 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 00 00

00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <16us
			ClockPM- Surprise- LLActRep+ BwNot-
		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #0, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
			Changed: MRL- PresDet- LinkState-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
	Capabilities: [90] Subsystem: Dell Device 04b3
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: pcieport
	Kernel modules: shpchp
00: 86 80 10 1c 07 00 10 00 b5 00 04 06 10 00 81 00
10: 00 00 00 00 00 00 00 00 00 03 04 00 f0 00 00 20
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 10 00

00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=05, subordinate=06, sec-latency=0
	I/O behind bridge: 0000e000-0000efff
	Prefetchable memory behind bridge: 00000000f1100000-00000000f11fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #2, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
			ClockPM- Surprise- LLActRep+ BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #1, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet- LinkState+
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
	Capabilities: [90] Subsystem: Dell Device 04b3
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: pcieport
	Kernel modules: shpchp
00: 86 80 12 1c 07 00 10 00 b5 00 04 06 10 00 81 00
10: 00 00 00 00 00 00 00 00 00 05 06 00 e0 e0 00 00
20: f0 ff 00 00 11 f1 11 f1 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 05 02 10 00

00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=09, subordinate=0a, sec-latency=0
	Memory behind bridge: f7e00000-f7efffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #4, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
			ClockPM- Surprise- LLActRep+ BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #3, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet- LinkState+
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
	Capabilities: [90] Subsystem: Dell Device 04b3
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: pcieport
	Kernel modules: shpchp
00: 86 80 16 1c 07 00 10 00 b5 00 04 06 10 00 81 00
10: 00 00 00 00 00 00 00 00 00 09 0a 00 f0 00 00 20
20: e0 f7 e0 f7 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 04 10 00

00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=0b, subordinate=0c, sec-latency=0
	Memory behind bridge: f7d00000-f7dfffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #5, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
			ClockPM- Surprise- LLActRep+ BwNot-
		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt+
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #4, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet- LinkState+
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
	Capabilities: [90] Subsystem: Dell Device 04b3
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: pcieport
	Kernel modules: shpchp
00: 86 80 18 1c 07 00 10 00 b5 00 04 06 10 00 81 00
10: 00 00 00 00 00 00 00 00 00 0b 0c 00 f0 00 00 20
20: d0 f7 d0 f7 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 10 00

00:1c.7 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=11, subordinate=16, sec-latency=0
	I/O behind bridge: 0000c000-0000dfff
	Memory behind bridge: f6c00000-f7cfffff
	Prefetchable memory behind bridge: 00000000f0000000-00000000f10fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #8, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
			ClockPM- Surprise- LLActRep+ BwNot-
		LnkCtl:	ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
			Slot #7, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq+ LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet- LinkState+
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee00318  Data: 0000
	Capabilities: [90] Subsystem: Dell Device 04b3
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: pcieport
	Kernel modules: shpchp
00: 86 80 1e 1c 07 04 10 20 b5 00 04 06 10 00 81 00
10: 00 00 00 00 00 00 00 00 00 11 16 00 c0 d0 00 00
20: c0 f6 c0 f7 01 f0 01 f1 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 04 10 00

00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) (prog-if 20 [EHCI])
	Subsystem: Dell Device 04b3
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 23
	Region 0: Memory at f7f07000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Debug port: BAR=1 offset=00a0
	Capabilities: [98] PCI Advanced Features
		AFCap: TP+ FLR+
		AFCtrl: FLR-
		AFStatus: TP-
	Kernel driver in use: ehci_hcd
00: 86 80 26 1c 06 00 90 02 05 20 03 0c 00 00 00 00
10: 00 70 f0 f7 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 00 00

00:1f.0 ISA bridge: Intel Corporation HM67 Express Chipset Family LPC Controller (rev 05)
	Subsystem: Dell Device 04b3
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00: 86 80 4b 1c 07 00 10 02 05 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00

00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) (prog-if 01 [AHCI 1.0])
	Subsystem: Dell Device 04b3
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 44
	Region 0: I/O ports at f0b0 [size=8]
	Region 1: I/O ports at f0a0 [size=4]
	Region 2: I/O ports at f090 [size=8]
	Region 3: I/O ports at f080 [size=4]
	Region 4: I/O ports at f060 [size=32]
	Region 5: Memory at f7f06000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee00338  Data: 0000
	Capabilities: [70] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
	Capabilities: [b0] PCI Advanced Features
		AFCap: TP+ FLR+
		AFCtrl: FLR-
		AFStatus: TP-
	Kernel driver in use: ahci
00: 86 80 03 1c 07 04 b0 02 05 01 06 01 00 00 00 00
10: b1 f0 00 00 a1 f0 00 00 91 f0 00 00 81 f0 00 00
20: 61 f0 00 00 00 60 f0 f7 00 00 00 00 28 10 b3 04
30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 02 00 00

00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05)
	Subsystem: Dell Device 04b3
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin C routed to IRQ 18
	Region 0: Memory at f7f05000 (64-bit, non-prefetchable) [size=256]
	Region 4: I/O ports at f040 [size=32]
	Kernel modules: i2c-i801
00: 86 80 22 1c 03 00 80 02 05 00 05 0c 00 00 00 00
10: 04 50 f0 f7 00 00 00 00 00 00 00 00 00 00 00 00
20: 41 f0 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 00 00 00 00 00 00 00 00 03 03 00 00

05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
	Subsystem: Dell Device 04b3
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 45
	Region 0: I/O ports at e000 [size=256]
	Region 2: Memory at f1104000 (64-bit, prefetchable) [size=4K]
	Region 4: Memory at f1100000 (64-bit, prefetchable) [size=16K]
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
		Address: 00000000fee00358  Data: 0000
	Capabilities: [70] Express (v2) Endpoint, MSI 01
		DevCap:	MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 4096 bytes
		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
			ClockPM+ Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Not Supported, TimeoutDis+
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
		Vector table: BAR=4 offset=00000000
		PBA: BAR=4 offset=00000800
	Capabilities: [d0] Vital Product Data
		Unknown small resource type 00, will not decode more.
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
	Capabilities: [140 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00
	Kernel driver in use: r8169
00: ec 10 68 81 07 04 10 00 06 00 00 02 10 00 00 00
10: 01 e0 00 00 00 00 00 00 0c 40 10 f1 00 00 00 00
20: 0c 00 10 f1 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 40 00 00 00 00 00 00 00 05 01 00 00

09:00.0 Network controller: Intel Corporation Centrino Wireless-N 1030 (rev 34)
	Subsystem: Intel Corporation Centrino Wireless-N 1030 BGN
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 53
	Region 0: Memory at f7e00000 (64-bit, non-prefetchable) [size=8K]
	Capabilities: [c8] Power Management version 3
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
		Address: 00000000fee003f8  Data: 0000
	Capabilities: [e0] Express (v1) Endpoint, MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 unlimited
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 <32us
			ClockPM+ Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
	Capabilities: [140 v1] Device Serial Number 4c-80-93-ff-ff-15-e6-c7
	Kernel driver in use: iwlwifi
	Kernel modules: iwlwifi
00: 86 80 8a 00 06 00 10 00 34 00 80 02 10 00 00 00
10: 04 00 e0 f7 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 25 53
30: 00 00 00 00 c8 00 00 00 00 00 00 00 0a 01 00 00

0b:00.0 USB controller: Texas Instruments Device 8241 (rev 02) (prog-if 30 [XHCI])
	Subsystem: Dell Device 04b3
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at f7d00000 (64-bit, non-prefetchable) [size=64K]
	Region 2: Memory at f7d10000 (64-bit, non-prefetchable) [size=8K]
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [48] MSI: Enable- Count=1/8 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [70] Express (v2) Endpoint, MSI 00
		DevCap:	MaxPayload 1024 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
			ClockPM+ Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Not Supported, TimeoutDis+
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [c0] MSI-X: Enable+ Count=8 Masked-
		Vector table: BAR=2 offset=00000000
		PBA: BAR=2 offset=00001000
	Capabilities: [100 v2] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP+ Rollover- Timeout- NonFatalErr+
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
	Capabilities: [150 v1] Device Serial Number 08-00-28-00-00-20-00-00
	Kernel driver in use: xhci_hcd
00: 4c 10 41 82 06 04 10 00 02 30 03 0c 10 00 00 00
10: 04 00 d0 f7 00 00 00 00 04 00 d1 f7 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00

11:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9123 PCIe SATA 6.0 Gb/s controller (rev 11) (prog-if 01 [AHCI 1.0])
	Subsystem: Device 18ab:9115
	Physical Slot: 7
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 54
	Region 0: I/O ports at c010 [size=8]
	Region 1: I/O ports at c020 [size=4]
	Region 2: I/O ports at c018 [size=8]
	Region 3: I/O ports at c024 [size=4]
	Region 4: I/O ports at c000 [size=16]
	Region 5: Memory at f6c00000 (32-bit, non-prefetchable) [size=2K]
	Expansion ROM at f0000000 [disabled] [size=64K]
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee00518  Data: 0000
	Capabilities: [70] Express (v2) Legacy Endpoint, MSI 00
		DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
			ClockPM- Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Not Supported, TimeoutDis+
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
	Kernel driver in use: ahci
00: 4b 1b 23 91 07 05 10 00 11 01 06 01 08 00 00 00
10: 11 c0 00 00 21 c0 00 00 19 c0 00 00 25 c0 00 00
20: 01 c0 00 00 00 00 c0 f6 00 00 00 00 ab 18 15 91
30: 00 00 00 d0 40 00 00 00 00 00 00 00 00 01 00 00


# dmesg
pciehp 0000:00:1c.7:pcie04: Card present on Slot(7)
pci 0000:11:00.0: [1b4b:9123] type 0 class 0x000106
pci 0000:11:00.0: reg 10: [io  0x8000-0x8007]
pci 0000:11:00.0: reg 14: [io  0x8040-0x8043]
pci 0000:11:00.0: reg 18: [io  0x8100-0x8107]
pci 0000:11:00.0: reg 1c: [io  0x8140-0x8143]
pci 0000:11:00.0: reg 20: [io  0x800000-0x80000f]
pci 0000:11:00.0: reg 24: [mem 0x00900000-0x009007ff]
pci 0000:11:00.0: reg 30: [mem 0xd0000000-0xd000ffff pref]
pci 0000:11:00.0: PME# supported from D3hot
pci 0000:11:00.0: PME# disabled
pci 0000:11:00.0: BAR 6: assigned [mem 0xf0000000-0xf000ffff pref]
pci 0000:11:00.0: BAR 5: assigned [mem 0xf6c00000-0xf6c007ff]
pci 0000:11:00.0: BAR 5: set to [mem 0xf6c00000-0xf6c007ff] (PCI address [0xf6c00000-0xf6c007ff])
pci 0000:11:00.0: BAR 4: assigned [io  0xc000-0xc00f]
pci 0000:11:00.0: BAR 4: set to [io  0xc000-0xc00f] (PCI address [0xc000-0xc00f])
pci 0000:11:00.0: BAR 0: assigned [io  0xc010-0xc017]
pci 0000:11:00.0: BAR 0: set to [io  0xc010-0xc017] (PCI address [0xc010-0xc017])
pci 0000:11:00.0: BAR 2: assigned [io  0xc018-0xc01f]
pci 0000:11:00.0: BAR 2: set to [io  0xc018-0xc01f] (PCI address [0xc018-0xc01f])
pci 0000:11:00.0: BAR 1: assigned [io  0xc020-0xc023]
pci 0000:11:00.0: BAR 1: set to [io  0xc020-0xc023] (PCI address [0xc020-0xc023])
pci 0000:11:00.0: BAR 3: assigned [io  0xc024-0xc027]
pci 0000:11:00.0: BAR 3: set to [io  0xc024-0xc027] (PCI address [0xc024-0xc027])
pcieport 0000:00:1c.7: PCI bridge to [bus 11-16]
pcieport 0000:00:1c.7:   bridge window [io  0xc000-0xdfff]
pcieport 0000:00:1c.7:   bridge window [mem 0xf6c00000-0xf7cfffff]
pcieport 0000:00:1c.7:   bridge window [mem 0xf0000000-0xf10fffff 64bit pref]
pcieport 0000:00:1c.7: setting latency timer to 64
ahci 0000:11:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ahci 0000:11:00.0: irq 54 for MSI/MSI-X
ahci 0000:11:00.0: controller can do FBS, turning on CAP_FBS
ahci 0000:11:00.0: AHCI 0001.0200 32 slots 8 ports 6 Gbps 0xff impl SATA mode
ahci 0000:11:00.0: flags: 64bit ncq fbs pio 
ahci 0000:11:00.0: setting latency timer to 64
scsi8 : ahci
scsi9 : ahci
scsi10 : ahci
scsi11 : ahci
scsi12 : ahci
scsi13 : ahci
scsi14 : ahci
scsi15 : ahci
ata7: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00100 irq 54
ata8: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00180 irq 54
ata9: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00200 irq 54
ata10: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00280 irq 54
ata11: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00300 irq 54
ata12: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00380 irq 54
ata13: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00400 irq 54
ata14: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00480 irq 54
ata11: SATA link down (SStatus 0 SControl 300)
ata13: SATA link down (SStatus 0 SControl 300)
ata9: SATA link down (SStatus 0 SControl 300)
ata10: SATA link down (SStatus 0 SControl 300)
ata7: SATA link down (SStatus 0 SControl 300)
ata12: SATA link down (SStatus 0 SControl 300)
ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata8: SATA link down (SStatus 0 SControl 300)
DRHD: handling fault status reg 2
DMAR:[DMA Read] Request device [11:00.1] fault addr fff00000 
DMAR:[fault reason 02] Present bit in context entry is clear
ata14.00: qc timeout (cmd 0xa1)
ata14.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata14.00: qc timeout (cmd 0xa1)
ata14.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata14: limiting SATA link speed to 1.5 Gbps
ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata14.00: qc timeout (cmd 0xa1)
ata14.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
pciehp 0000:00:1c.7:pcie04: Card not present on Slot(7)
ata7: failed to stop engine (-5)
ata8: failed to stop engine (-5)
ata9: failed to stop engine (-5)
ata10: failed to stop engine (-5)
ata11: failed to stop engine (-5)
ata12: failed to stop engine (-5)
ata13: failed to stop engine (-5)
ata14: failed to stop engine (-5)
ahci 0000:11:00.0: PCI INT A disabled
pciehp 0000:00:1c.7:pcie04: Card present on Slot(7)
pci 0000:11:00.0: [1b4b:9123] type 0 class 0x000106
pci 0000:11:00.0: reg 10: [io  0x8000-0x8007]
pci 0000:11:00.0: reg 14: [io  0x8040-0x8043]
pci 0000:11:00.0: reg 18: [io  0x8100-0x8107]
pci 0000:11:00.0: reg 1c: [io  0x8140-0x8143]
pci 0000:11:00.0: reg 20: [io  0x800000-0x80000f]
pci 0000:11:00.0: reg 24: [mem 0x00900000-0x009007ff]
pci 0000:11:00.0: reg 30: [mem 0xd0000000-0xd000ffff pref]
pci 0000:11:00.0: PME# supported from D3hot
pci 0000:11:00.0: PME# disabled
pci 0000:11:00.0: BAR 6: assigned [mem 0xf0000000-0xf000ffff pref]
pci 0000:11:00.0: BAR 5: assigned [mem 0xf6c00000-0xf6c007ff]
pci 0000:11:00.0: BAR 5: set to [mem 0xf6c00000-0xf6c007ff] (PCI address [0xf6c00000-0xf6c007ff])
pci 0000:11:00.0: BAR 4: assigned [io  0xc000-0xc00f]
pci 0000:11:00.0: BAR 4: set to [io  0xc000-0xc00f] (PCI address [0xc000-0xc00f])
pci 0000:11:00.0: BAR 0: assigned [io  0xc010-0xc017]
pci 0000:11:00.0: BAR 0: set to [io  0xc010-0xc017] (PCI address [0xc010-0xc017])
pci 0000:11:00.0: BAR 2: assigned [io  0xc018-0xc01f]
pci 0000:11:00.0: BAR 2: set to [io  0xc018-0xc01f] (PCI address [0xc018-0xc01f])
pci 0000:11:00.0: BAR 1: assigned [io  0xc020-0xc023]
pci 0000:11:00.0: BAR 1: set to [io  0xc020-0xc023] (PCI address [0xc020-0xc023])
pci 0000:11:00.0: BAR 3: assigned [io  0xc024-0xc027]
pci 0000:11:00.0: BAR 3: set to [io  0xc024-0xc027] (PCI address [0xc024-0xc027])
pcieport 0000:00:1c.7: PCI bridge to [bus 11-16]
pcieport 0000:00:1c.7:   bridge window [io  0xc000-0xdfff]
pcieport 0000:00:1c.7:   bridge window [mem 0xf6c00000-0xf7cfffff]
pcieport 0000:00:1c.7:   bridge window [mem 0xf0000000-0xf10fffff 64bit pref]
pcieport 0000:00:1c.7: setting latency timer to 64
ahci 0000:11:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ahci 0000:11:00.0: irq 54 for MSI/MSI-X
ahci 0000:11:00.0: controller can do FBS, turning on CAP_FBS
ahci 0000:11:00.0: AHCI 0001.0200 32 slots 8 ports 6 Gbps 0xff impl SATA mode
ahci 0000:11:00.0: flags: 64bit ncq fbs pio 
ahci 0000:11:00.0: setting latency timer to 64
scsi16 : ahci
scsi17 : ahci
scsi18 : ahci
scsi19 : ahci
scsi20 : ahci
scsi21 : ahci
scsi22 : ahci
scsi23 : ahci
ata15: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00100 irq 54
ata16: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00180 irq 54
ata17: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00200 irq 54
ata18: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00280 irq 54
ata19: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00300 irq 54
ata20: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00380 irq 54
ata21: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00400 irq 54
ata22: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00480 irq 54
ata21: SATA link down (SStatus 0 SControl 300)
ata20: SATA link down (SStatus 0 SControl 300)
ata17: SATA link down (SStatus 0 SControl 300)
ata18: SATA link down (SStatus 0 SControl 300)
ata19: SATA link down (SStatus 0 SControl 300)
ata15: SATA link down (SStatus 0 SControl 300)
ata22: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
DRHD: handling fault status reg 2
DMAR:[DMA Read] Request device [11:00.1] fault addr fff00000 
DMAR:[fault reason 02] Present bit in context entry is clear
ata16: SATA link down (SStatus 0 SControl 300)
ata22.00: qc timeout (cmd 0xa1)
ata22.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata22: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata22.00: qc timeout (cmd 0xa1)
ata22.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata22: limiting SATA link speed to 1.5 Gbps
ata22: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata22.00: qc timeout (cmd 0xa1)
ata22.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata22: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
pciehp 0000:00:1c.7:pcie04: Card not present on Slot(7)
ata15: failed to stop engine (-5)
ata16: failed to stop engine (-5)
ata17: failed to stop engine (-5)
ata18: failed to stop engine (-5)
ata19: failed to stop engine (-5)
ata20: failed to stop engine (-5)
ata21: failed to stop engine (-5)
ata22: failed to stop engine (-5)
ahci 0000:11:00.0: PCI INT A disabled
pciehp 0000:00:1c.7:pcie04: Card present on Slot(7)
pci 0000:11:00.0: [1b4b:9123] type 0 class 0x000106
pci 0000:11:00.0: reg 10: [io  0x8000-0x8007]
pci 0000:11:00.0: reg 14: [io  0x8040-0x8043]
pci 0000:11:00.0: reg 18: [io  0x8100-0x8107]
pci 0000:11:00.0: reg 1c: [io  0x8140-0x8143]
pci 0000:11:00.0: reg 20: [io  0x800000-0x80000f]
pci 0000:11:00.0: reg 24: [mem 0x00900000-0x009007ff]
pci 0000:11:00.0: reg 30: [mem 0xd0000000-0xd000ffff pref]
pci 0000:11:00.0: PME# supported from D3hot
pci 0000:11:00.0: PME# disabled
pci 0000:11:00.0: BAR 6: assigned [mem 0xf0000000-0xf000ffff pref]
pci 0000:11:00.0: BAR 5: assigned [mem 0xf6c00000-0xf6c007ff]
pci 0000:11:00.0: BAR 5: set to [mem 0xf6c00000-0xf6c007ff] (PCI address [0xf6c00000-0xf6c007ff])
pci 0000:11:00.0: BAR 4: assigned [io  0xc000-0xc00f]
pci 0000:11:00.0: BAR 4: set to [io  0xc000-0xc00f] (PCI address [0xc000-0xc00f])
pci 0000:11:00.0: BAR 0: assigned [io  0xc010-0xc017]
pci 0000:11:00.0: BAR 0: set to [io  0xc010-0xc017] (PCI address [0xc010-0xc017])
pci 0000:11:00.0: BAR 2: assigned [io  0xc018-0xc01f]
pci 0000:11:00.0: BAR 2: set to [io  0xc018-0xc01f] (PCI address [0xc018-0xc01f])
pci 0000:11:00.0: BAR 1: assigned [io  0xc020-0xc023]
pci 0000:11:00.0: BAR 1: set to [io  0xc020-0xc023] (PCI address [0xc020-0xc023])
pci 0000:11:00.0: BAR 3: assigned [io  0xc024-0xc027]
pci 0000:11:00.0: BAR 3: set to [io  0xc024-0xc027] (PCI address [0xc024-0xc027])
pcieport 0000:00:1c.7: PCI bridge to [bus 11-16]
pcieport 0000:00:1c.7:   bridge window [io  0xc000-0xdfff]
pcieport 0000:00:1c.7:   bridge window [mem 0xf6c00000-0xf7cfffff]
pcieport 0000:00:1c.7:   bridge window [mem 0xf0000000-0xf10fffff 64bit pref]
pcieport 0000:00:1c.7: setting latency timer to 64
ahci 0000:11:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ahci 0000:11:00.0: irq 54 for MSI/MSI-X
ahci 0000:11:00.0: controller can do FBS, turning on CAP_FBS
ahci 0000:11:00.0: AHCI 0001.0200 32 slots 8 ports 6 Gbps 0xff impl SATA mode
ahci 0000:11:00.0: flags: 64bit ncq fbs pio 
ahci 0000:11:00.0: setting latency timer to 64
scsi24 : ahci
scsi25 : ahci
scsi26 : ahci
scsi27 : ahci
scsi28 : ahci
scsi29 : ahci
scsi30 : ahci
scsi31 : ahci
ata23: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00100 irq 54
ata24: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00180 irq 54
ata25: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00200 irq 54
ata26: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00280 irq 54
ata27: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00300 irq 54
ata28: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00380 irq 54
ata29: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00400 irq 54
ata30: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00480 irq 54
ata27: SATA link down (SStatus 0 SControl 300)
ata26: SATA link down (SStatus 0 SControl 300)
ata29: SATA link down (SStatus 0 SControl 300)
ata23: SATA link down (SStatus 0 SControl 300)
ata28: SATA link down (SStatus 0 SControl 300)
ata24: SATA link down (SStatus 0 SControl 300)
ata30: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
DRHD: handling fault status reg 2
DMAR:[DMA Read] Request device [11:00.1] fault addr fff00000 
DMAR:[fault reason 02] Present bit in context entry is clear
ata25: SATA link down (SStatus 0 SControl 300)
ata30.00: qc timeout (cmd 0xa1)
ata30.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata30: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata30.00: qc timeout (cmd 0xa1)
ata30.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata30: limiting SATA link speed to 1.5 Gbps
ata30: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata30.00: qc timeout (cmd 0xa1)
ata30.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata30: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
pciehp 0000:00:1c.7:pcie04: Card not present on Slot(7)
ata23: failed to stop engine (-5)
ata24: failed to stop engine (-5)
ata25: failed to stop engine (-5)
ata26: failed to stop engine (-5)
ata27: failed to stop engine (-5)
ata28: failed to stop engine (-5)
ata29: failed to stop engine (-5)
ata30: failed to stop engine (-5)
ahci 0000:11:00.0: PCI INT A disabled
pciehp 0000:00:1c.7:pcie04: Card present on Slot(7)
pci 0000:11:00.0: [1b4b:9123] type 0 class 0x000106
pci 0000:11:00.0: reg 10: [io  0x8000-0x8007]
pci 0000:11:00.0: reg 14: [io  0x8040-0x8043]
pci 0000:11:00.0: reg 18: [io  0x8100-0x8107]
pci 0000:11:00.0: reg 1c: [io  0x8140-0x8143]
pci 0000:11:00.0: reg 20: [io  0x800000-0x80000f]
pci 0000:11:00.0: reg 24: [mem 0x00900000-0x009007ff]
pci 0000:11:00.0: reg 30: [mem 0xd0000000-0xd000ffff pref]
pci 0000:11:00.0: PME# supported from D3hot
pci 0000:11:00.0: PME# disabled
pci 0000:11:00.0: BAR 6: assigned [mem 0xf0000000-0xf000ffff pref]
pci 0000:11:00.0: BAR 5: assigned [mem 0xf6c00000-0xf6c007ff]
pci 0000:11:00.0: BAR 5: set to [mem 0xf6c00000-0xf6c007ff] (PCI address [0xf6c00000-0xf6c007ff])
pci 0000:11:00.0: BAR 4: assigned [io  0xc000-0xc00f]
pci 0000:11:00.0: BAR 4: set to [io  0xc000-0xc00f] (PCI address [0xc000-0xc00f])
pci 0000:11:00.0: BAR 0: assigned [io  0xc010-0xc017]
pci 0000:11:00.0: BAR 0: set to [io  0xc010-0xc017] (PCI address [0xc010-0xc017])
pci 0000:11:00.0: BAR 2: assigned [io  0xc018-0xc01f]
pci 0000:11:00.0: BAR 2: set to [io  0xc018-0xc01f] (PCI address [0xc018-0xc01f])
pci 0000:11:00.0: BAR 1: assigned [io  0xc020-0xc023]
pci 0000:11:00.0: BAR 1: set to [io  0xc020-0xc023] (PCI address [0xc020-0xc023])
pci 0000:11:00.0: BAR 3: assigned [io  0xc024-0xc027]
pci 0000:11:00.0: BAR 3: set to [io  0xc024-0xc027] (PCI address [0xc024-0xc027])
pcieport 0000:00:1c.7: PCI bridge to [bus 11-16]
pcieport 0000:00:1c.7:   bridge window [io  0xc000-0xdfff]
pcieport 0000:00:1c.7:   bridge window [mem 0xf6c00000-0xf7cfffff]
pcieport 0000:00:1c.7:   bridge window [mem 0xf0000000-0xf10fffff 64bit pref]
pcieport 0000:00:1c.7: setting latency timer to 64
ahci 0000:11:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ahci 0000:11:00.0: irq 54 for MSI/MSI-X
ahci 0000:11:00.0: controller can do FBS, turning on CAP_FBS
ahci 0000:11:00.0: AHCI 0001.0200 32 slots 8 ports 6 Gbps 0xff impl SATA mode
ahci 0000:11:00.0: flags: 64bit ncq fbs pio 
ahci 0000:11:00.0: setting latency timer to 64
scsi32 : ahci
scsi33 : ahci
scsi34 : ahci
scsi35 : ahci
scsi36 : ahci
scsi37 : ahci
scsi38 : ahci
scsi39 : ahci
ata31: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00100 irq 54
ata32: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00180 irq 54
ata33: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00200 irq 54
ata34: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00280 irq 54
ata35: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00300 irq 54
ata36: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00380 irq 54
ata37: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00400 irq 54
ata38: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00480 irq 54
ata33: SATA link down (SStatus 0 SControl 300)
ata37: SATA link down (SStatus 0 SControl 300)
ata32: SATA link down (SStatus 0 SControl 300)
ata31: SATA link down (SStatus 0 SControl 300)
ata34: SATA link down (SStatus 0 SControl 300)
ata35: SATA link down (SStatus 0 SControl 300)
ata38: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
DRHD: handling fault status reg 2
ata36: SATA link down (SStatus 0 SControl 300)
DMAR:[DMA Read] Request device [11:00.1] fault addr fff00000 
DMAR:[fault reason 02] Present bit in context entry is clear
ata38.00: qc timeout (cmd 0xa1)
ata38.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata38: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata38.00: qc timeout (cmd 0xa1)
ata38.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata38: limiting SATA link speed to 1.5 Gbps
ata38: SATA link up 1.5 Gbps (SStatus 113 SControl 310)

[-- Attachment #3: Axago_ECS-6S__fresh_boot_attempt.txt --]
[-- Type: text/plain, Size: 88151 bytes --]

# lspci
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05)
00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05)
00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5)
00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5)
00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5)
00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b5)
00:1c.7 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 (rev b5)
00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05)
00:1f.0 ISA bridge: Intel Corporation HM67 Express Chipset Family LPC Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05)
00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05)
05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
09:00.0 Network controller: Intel Corporation Centrino Wireless-N 1030 (rev 34)
0b:00.0 USB controller: Texas Instruments Device 8241 (rev 02)
11:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9123 PCIe SATA 6.0 Gb/s controller (rev 11)
#


# lspci -vvx
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
	Subsystem: Dell Device 04b3
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: [e0] Vendor Specific Information: Len=0c <?>
	Kernel driver in use: agpgart-intel
00: 86 80 04 01 06 00 90 20 09 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00

00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller])
	Subsystem: Dell Device 04b3
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 43
	Region 0: Memory at f6800000 (64-bit, non-prefetchable) [size=4M]
	Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
	Region 4: I/O ports at f000 [size=64]
	Expansion ROM at <unassigned> [disabled]
	Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee00018  Data: 0000
	Capabilities: [d0] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [a4] PCI Advanced Features
		AFCap: TP+ FLR+
		AFCtrl: FLR-
		AFStatus: TP-
	Kernel driver in use: i915
00: 86 80 26 01 07 04 90 00 09 00 00 03 00 00 00 00
10: 04 00 80 f6 00 00 00 00 0c 00 00 e0 00 00 00 00
20: 01 f0 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 90 00 00 00 00 00 00 00 0b 01 00 00

00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)
	Subsystem: Dell Device 04b3
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 51
	Region 0: Memory at f7f0a000 (64-bit, non-prefetchable) [size=16]
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+
		Address: 00000000fee00378  Data: 0000
	Kernel driver in use: mei
00: 86 80 3a 1c 06 04 10 00 04 00 80 07 00 00 80 00
10: 04 a0 f0 f7 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 00 00

00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) (prog-if 20 [EHCI])
	Subsystem: Dell Device 04b3
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at f7f08000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Debug port: BAR=1 offset=00a0
	Capabilities: [98] PCI Advanced Features
		AFCap: TP+ FLR+
		AFCtrl: FLR-
		AFStatus: TP-
	Kernel driver in use: ehci_hcd
00: 86 80 2d 1c 06 00 90 02 05 20 03 0c 00 00 00 00
10: 00 80 f0 f7 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 00 00

00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05)
	Subsystem: Dell Device 04b3
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 52
	Region 0: Memory at f7f00000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
		Address: 00000000fee003b8  Data: 0000
	Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- RBE- FLReset+
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
			ClockPM- Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
	Capabilities: [100 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=01
			Status:	NegoPending- InProgress-
		VC1:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=1 ArbSelect=Fixed TC/VC=22
			Status:	NegoPending- InProgress-
	Capabilities: [130 v1] Root Complex Link
		Desc:	PortNumber=0f ComponentID=00 EltType=Config
		Link0:	Desc:	TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+
			Addr:	00000000fed1c000
	Kernel driver in use: snd_hda_intel
00: 86 80 20 1c 06 04 10 00 05 00 03 04 10 00 00 00
10: 04 00 f0 f7 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 00 00

00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <16us
			ClockPM- Surprise- LLActRep+ BwNot-
		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #0, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
			Changed: MRL- PresDet- LinkState-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
	Capabilities: [90] Subsystem: Dell Device 04b3
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: pcieport
	Kernel modules: shpchp
00: 86 80 10 1c 07 00 10 00 b5 00 04 06 10 00 81 00
10: 00 00 00 00 00 00 00 00 00 03 04 00 f0 00 00 20
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 10 00

00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=05, subordinate=06, sec-latency=0
	I/O behind bridge: 0000e000-0000efff
	Prefetchable memory behind bridge: 00000000f1100000-00000000f11fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #2, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
			ClockPM- Surprise- LLActRep+ BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #1, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet- LinkState+
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
	Capabilities: [90] Subsystem: Dell Device 04b3
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: pcieport
	Kernel modules: shpchp
00: 86 80 12 1c 07 00 10 00 b5 00 04 06 10 00 81 00
10: 00 00 00 00 00 00 00 00 00 05 06 00 e0 e0 00 00
20: f0 ff 00 00 11 f1 11 f1 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 05 02 10 00

00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=09, subordinate=0a, sec-latency=0
	Memory behind bridge: f7e00000-f7efffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #4, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
			ClockPM- Surprise- LLActRep+ BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #3, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet- LinkState+
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
	Capabilities: [90] Subsystem: Dell Device 04b3
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: pcieport
	Kernel modules: shpchp
00: 86 80 16 1c 07 00 10 00 b5 00 04 06 10 00 81 00
10: 00 00 00 00 00 00 00 00 00 09 0a 00 f0 00 00 20
20: e0 f7 e0 f7 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 04 10 00

00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=0b, subordinate=0c, sec-latency=0
	Memory behind bridge: f7d00000-f7dfffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #5, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
			ClockPM- Surprise- LLActRep+ BwNot-
		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt+
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #4, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet- LinkState+
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
	Capabilities: [90] Subsystem: Dell Device 04b3
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: pcieport
	Kernel modules: shpchp
00: 86 80 18 1c 07 00 10 00 b5 00 04 06 10 00 81 00
10: 00 00 00 00 00 00 00 00 00 0b 0c 00 f0 00 00 20
20: d0 f7 d0 f7 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 10 00

00:1c.7 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=11, subordinate=16, sec-latency=0
	I/O behind bridge: 0000c000-0000dfff
	Memory behind bridge: f6c00000-f7cfffff
	Prefetchable memory behind bridge: 00000000f0000000-00000000f10fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #8, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
			ClockPM- Surprise- LLActRep+ BwNot-
		LnkCtl:	ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
			Slot #7, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq+ LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet- LinkState+
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee00318  Data: 0000
	Capabilities: [90] Subsystem: Dell Device 04b3
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: pcieport
	Kernel modules: shpchp
00: 86 80 1e 1c 07 04 10 20 b5 00 04 06 10 00 81 00
10: 00 00 00 00 00 00 00 00 00 11 16 00 c0 d0 00 00
20: c0 f6 c0 f7 01 f0 01 f1 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 04 10 00

00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) (prog-if 20 [EHCI])
	Subsystem: Dell Device 04b3
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 23
	Region 0: Memory at f7f07000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Debug port: BAR=1 offset=00a0
	Capabilities: [98] PCI Advanced Features
		AFCap: TP+ FLR+
		AFCtrl: FLR-
		AFStatus: TP-
	Kernel driver in use: ehci_hcd
00: 86 80 26 1c 06 00 90 02 05 20 03 0c 00 00 00 00
10: 00 70 f0 f7 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 00 00

00:1f.0 ISA bridge: Intel Corporation HM67 Express Chipset Family LPC Controller (rev 05)
	Subsystem: Dell Device 04b3
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00: 86 80 4b 1c 07 00 10 02 05 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00

00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) (prog-if 01 [AHCI 1.0])
	Subsystem: Dell Device 04b3
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 44
	Region 0: I/O ports at f0b0 [size=8]
	Region 1: I/O ports at f0a0 [size=4]
	Region 2: I/O ports at f090 [size=8]
	Region 3: I/O ports at f080 [size=4]
	Region 4: I/O ports at f060 [size=32]
	Region 5: Memory at f7f06000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee00338  Data: 0000
	Capabilities: [70] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
	Capabilities: [b0] PCI Advanced Features
		AFCap: TP+ FLR+
		AFCtrl: FLR-
		AFStatus: TP-
	Kernel driver in use: ahci
00: 86 80 03 1c 07 04 b0 02 05 01 06 01 00 00 00 00
10: b1 f0 00 00 a1 f0 00 00 91 f0 00 00 81 f0 00 00
20: 61 f0 00 00 00 60 f0 f7 00 00 00 00 28 10 b3 04
30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 02 00 00

00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05)
	Subsystem: Dell Device 04b3
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin C routed to IRQ 18
	Region 0: Memory at f7f05000 (64-bit, non-prefetchable) [size=256]
	Region 4: I/O ports at f040 [size=32]
	Kernel modules: i2c-i801
00: 86 80 22 1c 03 00 80 02 05 00 05 0c 00 00 00 00
10: 04 50 f0 f7 00 00 00 00 00 00 00 00 00 00 00 00
20: 41 f0 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 00 00 00 00 00 00 00 00 03 03 00 00

05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
	Subsystem: Dell Device 04b3
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 45
	Region 0: I/O ports at e000 [size=256]
	Region 2: Memory at f1104000 (64-bit, prefetchable) [size=4K]
	Region 4: Memory at f1100000 (64-bit, prefetchable) [size=16K]
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
		Address: 00000000fee00358  Data: 0000
	Capabilities: [70] Express (v2) Endpoint, MSI 01
		DevCap:	MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 4096 bytes
		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
			ClockPM+ Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Not Supported, TimeoutDis+
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
		Vector table: BAR=4 offset=00000000
		PBA: BAR=4 offset=00000800
	Capabilities: [d0] Vital Product Data
		Unknown small resource type 00, will not decode more.
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
	Capabilities: [140 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00
	Kernel driver in use: r8169
00: ec 10 68 81 07 04 10 00 06 00 00 02 10 00 00 00
10: 01 e0 00 00 00 00 00 00 0c 40 10 f1 00 00 00 00
20: 0c 00 10 f1 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 40 00 00 00 00 00 00 00 05 01 00 00

09:00.0 Network controller: Intel Corporation Centrino Wireless-N 1030 (rev 34)
	Subsystem: Intel Corporation Centrino Wireless-N 1030 BGN
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 53
	Region 0: Memory at f7e00000 (64-bit, non-prefetchable) [size=8K]
	Capabilities: [c8] Power Management version 3
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
		Address: 00000000fee003f8  Data: 0000
	Capabilities: [e0] Express (v1) Endpoint, MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 unlimited
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 <32us
			ClockPM+ Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
	Capabilities: [140 v1] Device Serial Number 4c-80-93-ff-ff-15-e6-c7
	Kernel driver in use: iwlwifi
	Kernel modules: iwlwifi
00: 86 80 8a 00 06 00 10 00 34 00 80 02 10 00 00 00
10: 04 00 e0 f7 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 25 53
30: 00 00 00 00 c8 00 00 00 00 00 00 00 0a 01 00 00

0b:00.0 USB controller: Texas Instruments Device 8241 (rev 02) (prog-if 30 [XHCI])
	Subsystem: Dell Device 04b3
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at f7d00000 (64-bit, non-prefetchable) [size=64K]
	Region 2: Memory at f7d10000 (64-bit, non-prefetchable) [size=8K]
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [48] MSI: Enable- Count=1/8 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [70] Express (v2) Endpoint, MSI 00
		DevCap:	MaxPayload 1024 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
			ClockPM+ Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Not Supported, TimeoutDis+
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [c0] MSI-X: Enable+ Count=8 Masked-
		Vector table: BAR=2 offset=00000000
		PBA: BAR=2 offset=00001000
	Capabilities: [100 v2] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
	Capabilities: [150 v1] Device Serial Number 08-00-28-00-00-20-00-00
	Kernel driver in use: xhci_hcd
00: 4c 10 41 82 06 04 10 00 02 30 03 0c 10 00 00 00
10: 04 00 d0 f7 00 00 00 00 04 00 d1 f7 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00

11:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9123 PCIe SATA 6.0 Gb/s controller (rev 11) (prog-if 01 [AHCI 1.0])
	Subsystem: Device 18ab:9115
	Physical Slot: 7
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 54
	Region 0: I/O ports at c010 [size=8]
	Region 1: I/O ports at c020 [size=4]
	Region 2: I/O ports at c018 [size=8]
	Region 3: I/O ports at c024 [size=4]
	Region 4: I/O ports at c000 [size=16]
	Region 5: Memory at f6c00000 (32-bit, non-prefetchable) [size=2K]
	Expansion ROM at f0000000 [disabled] [size=64K]
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee00518  Data: 0000
	Capabilities: [70] Express (v2) Legacy Endpoint, MSI 00
		DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
			ClockPM- Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Not Supported, TimeoutDis+
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
	Kernel driver in use: ahci
00: 4b 1b 23 91 07 05 10 00 11 01 06 01 08 00 00 00
10: 11 c0 00 00 21 c0 00 00 19 c0 00 00 25 c0 00 00
20: 01 c0 00 00 00 00 c0 f6 00 00 00 00 ab 18 15 91
30: 00 00 00 d0 40 00 00 00 00 00 00 00 00 01 00 00

Initializing cgroup subsys cpu
Linux version 3.2.14-default (root@vostro) (gcc version 4.5.3 (Gentoo 4.5.3-r2 p1.1, pie-0.4.7) ) #1 SMP Wed Apr 11 18:40:41 MEST 2012
Command line: root=/dev/sda5
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009d400 (usable)
 BIOS-e820: 000000000009d400 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000020000000 (usable)
 BIOS-e820: 0000000020000000 - 0000000020200000 (reserved)
 BIOS-e820: 0000000020200000 - 0000000040000000 (usable)
 BIOS-e820: 0000000040000000 - 0000000040200000 (reserved)
 BIOS-e820: 0000000040200000 - 00000000da4e5000 (usable)
 BIOS-e820: 00000000da4e5000 - 00000000da528000 (ACPI NVS)
 BIOS-e820: 00000000da528000 - 00000000da793000 (usable)
 BIOS-e820: 00000000da793000 - 00000000da967000 (reserved)
 BIOS-e820: 00000000da967000 - 00000000daa89000 (usable)
 BIOS-e820: 00000000daa89000 - 00000000dad68000 (reserved)
 BIOS-e820: 00000000dad68000 - 00000000dafe8000 (ACPI NVS)
 BIOS-e820: 00000000dafe8000 - 00000000db000000 (ACPI data)
 BIOS-e820: 00000000db800000 - 00000000dfa00000 (reserved)
 BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fed00000 - 00000000fed04000 (reserved)
 BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
 BIOS-e820: 0000000100000000 - 000000041fe00000 (usable)
NX (Execute Disable) protection: active
DMI 2.6 present.
DMI: Dell Inc. Vostro 3550/0JGC48, BIOS A09 09/30/2011
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
No AGP bridge found
last_pfn = 0x41fe00 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
  00000-9FFFF write-back
  A0000-BFFFF uncachable
  C0000-CFFFF write-protect
  D0000-E7FFF uncachable
  E8000-FFFFF write-protect
MTRR variable ranges enabled:
  0 base 000000000 mask C00000000 write-back
  1 base 400000000 mask FE0000000 write-back
  2 base 0DB800000 mask FFF800000 uncachable
  3 base 0DC000000 mask FFC000000 uncachable
  4 base 0E0000000 mask FE0000000 uncachable
  5 base 41FE00000 mask FFFE00000 uncachable
  6 disabled
  7 disabled
  8 disabled
  9 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
e820 update range: 00000000db800000 - 0000000100000000 (usable) ==> (reserved)
last_pfn = 0xdaa89 max_arch_pfn = 0x400000000
initial memory mapped : 0 - 20000000
Base memory trampoline at [ffff880000098000] 98000 size 20480
init_memory_mapping: 0000000000000000-00000000daa89000
 0000000000 - 00daa00000 page 2M
 00daa00000 - 00daa89000 page 4k
kernel direct mapping tables up to daa89000 @ 1fffa000-20000000
init_memory_mapping: 0000000100000000-000000041fe00000
 0100000000 - 041fe00000 page 2M
kernel direct mapping tables up to 41fe00000 @ daa77000-daa89000
ACPI: RSDP 00000000000f0410 00024 (v02   DELL)
ACPI: XSDT 00000000dafe8078 00074 (v01 DELL    WN09    01072009 AMI  00010013)
ACPI: FACP 00000000daff1d08 000F4 (v04   DELL     WN09 01072009 AMI  00010013)
ACPI: DSDT 00000000dafe8180 09B85 (v02   DELL     WN09 00000000 INTL 20051117)
ACPI: FACS 00000000dafe3f80 00040
ACPI: APIC 00000000daff1e00 00072 (v03   DELL     WN09 01072009 AMI  00010013)
ACPI: MCFG 00000000daff1e78 0003C (v01   DELL     WN09 01072009 MSFT 00000097)
ACPI: SSDT 00000000daff1eb8 004B0 (v01 TrmRef PtidDevc 00001000 INTL 20091112)
ACPI: SLIC 00000000daff2368 00176 (v01 DELL    WN09    01072009 AMI  00010013)
ACPI: HPET 00000000daff24e0 00038 (v01   DELL     WN09 01072009 AMI. 00000004)
ACPI: SSDT 00000000daff2518 00846 (v01  PmRef  Cpu0Ist 00003000 INTL 20051117)
ACPI: SSDT 00000000daff2d60 00996 (v01  PmRef    CpuPm 00003000 INTL 20051117)
ACPI: DMAR 00000000daff36f8 000E8 (v01 INTEL      SNB  00000001 INTL 00000001)
ACPI: OSFR 00000000daff37e0 00086 (v01 DELL    M08     07DB091E ASL  00000061)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at 0000000000000000-000000041fe00000
Initmem setup node 0 0000000000000000-000000041fe00000
  NODE_DATA [000000041fdfb000 - 000000041fdfffff]
 [ffffea0000000000-ffffea000e7fffff] PMD -> [ffff88040f400000-ffff88041d5fffff] on node 0
Zone PFN ranges:
  DMA      0x00000010 -> 0x00001000
  DMA32    0x00001000 -> 0x00100000
  Normal   0x00100000 -> 0x0041fe00
Movable zone start PFN for each node
early_node_map[7] active PFN ranges
    0: 0x00000010 -> 0x0000009d
    0: 0x00000100 -> 0x00020000
    0: 0x00020200 -> 0x00040000
    0: 0x00040200 -> 0x000da4e5
    0: 0x000da528 -> 0x000da793
    0: 0x000da967 -> 0x000daa89
    0: 0x00100000 -> 0x0041fe00
On node 0 totalpages: 4170239
  DMA zone: 56 pages used for memmap
  DMA zone: 5 pages reserved
  DMA zone: 3920 pages, LIFO batch:0
  DMA32 zone: 14280 pages used for memmap
  DMA32 zone: 875690 pages, LIFO batch:31
  Normal zone: 44793 pages used for memmap
  Normal zone: 3231495 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a701 base: 0xfed00000
SMP: Allowing 4 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 40
PM: Registered nosave memory: 000000000009d000 - 000000000009e000
PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
PM: Registered nosave memory: 0000000020000000 - 0000000020200000
PM: Registered nosave memory: 0000000040000000 - 0000000040200000
PM: Registered nosave memory: 00000000da4e5000 - 00000000da528000
PM: Registered nosave memory: 00000000da793000 - 00000000da967000
PM: Registered nosave memory: 00000000daa89000 - 00000000dad68000
PM: Registered nosave memory: 00000000dad68000 - 00000000dafe8000
PM: Registered nosave memory: 00000000dafe8000 - 00000000db000000
PM: Registered nosave memory: 00000000db000000 - 00000000db800000
PM: Registered nosave memory: 00000000db800000 - 00000000dfa00000
PM: Registered nosave memory: 00000000dfa00000 - 00000000f8000000
PM: Registered nosave memory: 00000000f8000000 - 00000000fc000000
PM: Registered nosave memory: 00000000fc000000 - 00000000fec00000
PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
PM: Registered nosave memory: 00000000fec01000 - 00000000fed00000
PM: Registered nosave memory: 00000000fed00000 - 00000000fed04000
PM: Registered nosave memory: 00000000fed04000 - 00000000fed1c000
PM: Registered nosave memory: 00000000fed1c000 - 00000000fed20000
PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000
PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
PM: Registered nosave memory: 00000000fee01000 - 00000000ff000000
PM: Registered nosave memory: 00000000ff000000 - 0000000100000000
Allocating PCI resources starting at dfa00000 (gap: dfa00000:18600000)
setup_percpu: NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 25 pages/cpu @ffff88041fa00000 s71232 r8192 d22976 u524288
pcpu-alloc: s71232 r8192 d22976 u524288 alloc=1*2097152
pcpu-alloc: [0] 0 1 2 3 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 4111105
Policy zone: Normal
Kernel command line: root=/dev/sda5
PID hash table entries: 4096 (order: 3, 32768 bytes)
xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
Checking aperture...
No AGP bridge found
Memory: 16371224k/17299456k available (6262k kernel code, 618500k absent, 309732k reserved, 3868k data, 620k init)
Hierarchical RCU implementation.
	RCU dyntick-idle grace-period acceleration is enabled.
NR_IRQS:4352 nr_irqs:712 16
Extended CMOS year: 2000
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
Fast TSC calibration using PIT
Detected 2793.421 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 5586.84 BogoMIPS (lpj=27934210)
pid_max: default: 32768 minimum: 301
Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Mount-cache hash table entries: 256
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
mce: CPU supports 7 MCE banks
CPU0: Thermal monitoring enabled (TM1)
using mwait in idle threads.
ACPI: Core revision 20110623
DMAR: Host address width 36
DMAR: DRHD base: 0x000000fed90000 flags: 0x0
IOMMU 0: reg_base_addr fed90000 ver 1:0 cap c0000020e60262 ecap f0101a
DMAR: DRHD base: 0x000000fed91000 flags: 0x1
IOMMU 1: reg_base_addr fed91000 ver 1:0 cap c9008020660262 ecap f0105a
DMAR: RMRR base: 0x000000dad53000 end: 0x000000dad61fff
DMAR: RMRR base: 0x000000db800000 end: 0x000000df9fffff
IOAPIC id 2 under DRHD base  0xfed91000 IOMMU 1
HPET id 0 under DRHD base 0xfed91000
HPET id 0 under DRHD base 0xfed91000
HPET id 0 under DRHD base 0xfed91000
HPET id 0 under DRHD base 0xfed91000
HPET id 0 under DRHD base 0xfed91000
HPET id 0 under DRHD base 0xfed91000
HPET id 0 under DRHD base 0xfed91000
HPET id 0 under DRHD base 0xfed91000
Enabled IRQ remapping in xapic mode
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM) i7-2640M CPU @ 2.80GHz stepping 07
Performance Events: PEBS fmt1+, SandyBridge events, Intel PMU driver.
PEBS disabled due to CPU errata.
... version:                3
... bit width:              48
... generic registers:      4
... value mask:             0000ffffffffffff
... max period:             000000007fffffff
... fixed-purpose events:   3
... event mask:             000000070000000f
Booting Node   0, Processors  #1
smpboot cpu 1: start_ip = 98000
 #2
smpboot cpu 2: start_ip = 98000
 #3 Ok.
smpboot cpu 3: start_ip = 98000
Brought up 4 CPUs
Total of 4 processors activated (22348.48 BogoMIPS).
devtmpfs: initialized
PM: Registering ACPI NVS region at da4e5000 (274432 bytes)
PM: Registering ACPI NVS region at dad68000 (2621440 bytes)
xor: automatically using best checksumming function: generic_sse
   generic_sse: 12455.200 MB/sec
xor: using function: generic_sse (12455.200 MB/sec)
print_constraints: dummy: 
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
raid6: int64x1   2934 MB/s
raid6: int64x2   2971 MB/s
raid6: int64x4   2731 MB/s
raid6: int64x8   1731 MB/s
raid6: sse2x1    7584 MB/s
raid6: sse2x2    9385 MB/s
raid6: sse2x4   10651 MB/s
raid6: using algorithm sse2x4 (10651 MB/s)
ACPI: Added _OSI(Module Device)
ACPI: Added _OSI(Processor Device)
ACPI: Added _OSI(3.0 _SCP Extensions)
ACPI: Added _OSI(Processor Aggregator Device)
ACPI: EC: Look up EC in DSDT
ACPI: Executed 1 blocks of module-level executable AML code
[Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
ACPI: SSDT 00000000dad51698 0064F (v01  PmRef  Cpu0Cst 00003001 INTL 20051117)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT           (null) 0064F (v01  PmRef  Cpu0Cst 00003001 INTL 20051117)
ACPI: SSDT 00000000dad52a98 00303 (v01  PmRef    ApIst 00003000 INTL 20051117)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT           (null) 00303 (v01  PmRef    ApIst 00003000 INTL 20051117)
ACPI: SSDT 00000000dad50d98 00119 (v01  PmRef    ApCst 00003000 INTL 20051117)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT           (null) 00119 (v01  PmRef    ApCst 00003000 INTL 20051117)
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
HEST: Table not found.
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
pci_root PNP0A08:00: host bridge window [io  0x0000-0x0cf7]
pci_root PNP0A08:00: host bridge window [io  0x0d00-0xffff]
pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000d3fff]
pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff]
pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff]
pci_root PNP0A08:00: host bridge window [mem 0x000dc000-0x000dffff]
pci_root PNP0A08:00: host bridge window [mem 0x000e0000-0x000e3fff]
pci_root PNP0A08:00: host bridge window [mem 0x000e4000-0x000e7fff]
pci_root PNP0A08:00: host bridge window [mem 0xdfa00000-0xfeafffff]
pci_root PNP0A08:00: host bridge window [mem 0xfed40000-0xfed44fff]
pci 0000:00:00.0: [8086:0104] type 0 class 0x000600
pci 0000:00:02.0: [8086:0126] type 0 class 0x000300
pci 0000:00:02.0: reg 10: [mem 0xf6800000-0xf6bfffff 64bit]
pci 0000:00:02.0: reg 18: [mem 0xe0000000-0xefffffff 64bit pref]
pci 0000:00:02.0: reg 20: [io  0xf000-0xf03f]
pci 0000:00:16.0: [8086:1c3a] type 0 class 0x000780
pci 0000:00:16.0: reg 10: [mem 0xf7f0a000-0xf7f0a00f 64bit]
pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
pci 0000:00:16.0: PME# disabled
pci 0000:00:1a.0: [8086:1c2d] type 0 class 0x000c03
pci 0000:00:1a.0: reg 10: [mem 0xf7f08000-0xf7f083ff]
pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.0: PME# disabled
pci 0000:00:1b.0: [8086:1c20] type 0 class 0x000403
pci 0000:00:1b.0: reg 10: [mem 0xf7f00000-0xf7f03fff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: [8086:1c10] type 1 class 0x000604
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: [8086:1c12] type 1 class 0x000604
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.3: [8086:1c16] type 1 class 0x000604
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1c.4: [8086:1c18] type 1 class 0x000604
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1c.7: [8086:1c1e] type 1 class 0x000604
pci 0000:00:1c.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.7: PME# disabled
pci 0000:00:1d.0: [8086:1c26] type 0 class 0x000c03
pci 0000:00:1d.0: reg 10: [mem 0xf7f07000-0xf7f073ff]
pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.0: PME# disabled
pci 0000:00:1f.0: [8086:1c4b] type 0 class 0x000601
pci 0000:00:1f.2: [8086:1c03] type 0 class 0x000106
pci 0000:00:1f.2: reg 10: [io  0xf0b0-0xf0b7]
pci 0000:00:1f.2: reg 14: [io  0xf0a0-0xf0a3]
pci 0000:00:1f.2: reg 18: [io  0xf090-0xf097]
pci 0000:00:1f.2: reg 1c: [io  0xf080-0xf083]
pci 0000:00:1f.2: reg 20: [io  0xf060-0xf07f]
pci 0000:00:1f.2: reg 24: [mem 0xf7f06000-0xf7f067ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: [8086:1c22] type 0 class 0x000c05
pci 0000:00:1f.3: reg 10: [mem 0xf7f05000-0xf7f050ff 64bit]
pci 0000:00:1f.3: reg 20: [io  0xf040-0xf05f]
pci 0000:00:1c.0: PCI bridge to [bus 03-04]
pci 0000:05:00.0: [10ec:8168] type 0 class 0x000200
pci 0000:05:00.0: reg 10: [io  0xe000-0xe0ff]
pci 0000:05:00.0: reg 18: [mem 0xf1104000-0xf1104fff 64bit pref]
pci 0000:05:00.0: reg 20: [mem 0xf1100000-0xf1103fff 64bit pref]
pci 0000:05:00.0: supports D1 D2
pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:05:00.0: PME# disabled
pci 0000:00:1c.1: PCI bridge to [bus 05-06]
pci 0000:00:1c.1:   bridge window [io  0xe000-0xefff]
pci 0000:00:1c.1:   bridge window [mem 0xf1100000-0xf11fffff 64bit pref]
pci 0000:09:00.0: [8086:008a] type 0 class 0x000280
pci 0000:09:00.0: reg 10: [mem 0xf7e00000-0xf7e01fff 64bit]
pci 0000:09:00.0: PME# supported from D0 D3hot D3cold
pci 0000:09:00.0: PME# disabled
pci 0000:00:1c.3: PCI bridge to [bus 09-0a]
pci 0000:00:1c.3:   bridge window [mem 0xf7e00000-0xf7efffff]
pci 0000:0b:00.0: [104c:8241] type 0 class 0x000c03
pci 0000:0b:00.0: reg 10: [mem 0xf7d00000-0xf7d0ffff 64bit]
pci 0000:0b:00.0: reg 18: [mem 0xf7d10000-0xf7d11fff 64bit]
pci 0000:0b:00.0: supports D1 D2
pci 0000:0b:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:0b:00.0: PME# disabled
pci 0000:00:1c.4: PCI bridge to [bus 0b-0c]
pci 0000:00:1c.4:   bridge window [mem 0xf7d00000-0xf7dfffff]
pci 0000:00:1c.7: PCI bridge to [bus 11-16]
pci 0000:00:1c.7:   bridge window [io  0xc000-0xdfff]
pci 0000:00:1c.7:   bridge window [mem 0xf6c00000-0xf7cfffff]
pci 0000:00:1c.7:   bridge window [mem 0xf0000000-0xf10fffff 64bit pref]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP08._PRT]
 pci0000:00: Requesting ACPI _OSC control (0x1d)
 pci0000:00: ACPI _OSC control (0x19) granted
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 10 11 12 14 15)
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
vgaarb: bridge control possible 0000:00:02.0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
wmi: Mapper loaded
Advanced Linux Sound Architecture Driver Version 1.0.24.
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
reserve RAM buffer: 000000000009d400 - 000000000009ffff 
reserve RAM buffer: 00000000da4e5000 - 00000000dbffffff 
reserve RAM buffer: 00000000da793000 - 00000000dbffffff 
reserve RAM buffer: 00000000daa89000 - 00000000dbffffff 
reserve RAM buffer: 000000041fe00000 - 000000041fffffff 
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
hpet0: 8 comparators, 64-bit 14.318180 MHz counter
Switching to clocksource hpet
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: [bus 00-3e]
pnp 00:00: [io  0x0000-0x0cf7 window]
pnp 00:00: [io  0x0cf8-0x0cff]
pnp 00:00: [io  0x0d00-0xffff window]
pnp 00:00: [mem 0x000a0000-0x000bffff window]
pnp 00:00: [mem 0x000c0000-0x000c3fff window]
pnp 00:00: [mem 0x000c4000-0x000c7fff window]
pnp 00:00: [mem 0x000c8000-0x000cbfff window]
pnp 00:00: [mem 0x000cc000-0x000cffff window]
pnp 00:00: [mem 0x000d0000-0x000d3fff window]
pnp 00:00: [mem 0x000d4000-0x000d7fff window]
pnp 00:00: [mem 0x000d8000-0x000dbfff window]
pnp 00:00: [mem 0x000dc000-0x000dffff window]
pnp 00:00: [mem 0x000e0000-0x000e3fff window]
pnp 00:00: [mem 0x000e4000-0x000e7fff window]
pnp 00:00: [mem 0x000e8000-0x000ebfff window]
pnp 00:00: [mem 0x000ec000-0x000effff window]
pnp 00:00: [mem 0x000f0000-0x000fffff window]
pnp 00:00: [mem 0xdfa00000-0xfeafffff window]
pnp 00:00: [mem 0xfed40000-0xfed44fff window]
pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
pnp 00:01: [io  0x0000-0x001f]
pnp 00:01: [io  0x0081-0x0091]
pnp 00:01: [io  0x0093-0x009f]
pnp 00:01: [io  0x00c0-0x00df]
pnp 00:01: [dma 4]
pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
pnp 00:02: [mem 0xff000000-0xffffffff]
pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
pnp 00:03: [mem 0xfed00000-0xfed003ff]
pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)
pnp 00:04: [io  0x002e-0x002f]
pnp 00:04: [io  0x004e-0x004f]
pnp 00:04: [io  0x0061]
pnp 00:04: [io  0x0063]
pnp 00:04: [io  0x0065]
pnp 00:04: [io  0x0067]
pnp 00:04: [io  0x0070]
pnp 00:04: [io  0x0080]
pnp 00:04: [io  0x0092]
pnp 00:04: [io  0x00b2-0x00b3]
pnp 00:04: [io  0x0680-0x069f]
pnp 00:04: [io  0x1000-0x100f]
pnp 00:04: [io  0xffff]
pnp 00:04: [io  0xffff]
pnp 00:04: [io  0x0400-0x0453]
pnp 00:04: [io  0x0458-0x047f]
pnp 00:04: [io  0x0500-0x057f]
pnp 00:04: [io  0x164e-0x164f]
system 00:04: [io  0x0680-0x069f] has been reserved
system 00:04: [io  0x1000-0x100f] has been reserved
system 00:04: [io  0xffff] has been reserved
system 00:04: [io  0xffff] has been reserved
system 00:04: [io  0x0400-0x0453] has been reserved
system 00:04: [io  0x0458-0x047f] has been reserved
system 00:04: [io  0x0500-0x057f] has been reserved
system 00:04: [io  0x164e-0x164f] has been reserved
system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:05: [io  0x0070-0x0077]
pnp 00:05: [irq 8]
pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:06: [io  0x0454-0x0457]
system 00:06: [io  0x0454-0x0457] has been reserved
system 00:06: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
pnp 00:07: [io  0x00f0-0x00ff]
pnp 00:07: [irq 13]
pnp 00:07: Plug and Play ACPI device, IDs PNP0c04 (active)
pnp 00:08: [io  0x0010-0x001f]
pnp 00:08: [io  0x0022-0x003f]
pnp 00:08: [io  0x0044-0x005f]
pnp 00:08: [io  0x0068-0x006f]
pnp 00:08: [io  0x0072-0x007f]
pnp 00:08: [io  0x0080]
pnp 00:08: [io  0x0084-0x0086]
pnp 00:08: [io  0x0088]
pnp 00:08: [io  0x008c-0x008e]
pnp 00:08: [io  0x0090-0x009f]
pnp 00:08: [io  0x00a2-0x00bf]
pnp 00:08: [io  0x00e0-0x00ef]
pnp 00:08: [io  0x04d0-0x04d1]
pnp 00:08: [mem 0xfe800000-0xfe802fff]
system 00:08: [io  0x04d0-0x04d1] has been reserved
system 00:08: [mem 0xfe800000-0xfe802fff] has been reserved
system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:09: [irq 12]
pnp 00:09: Plug and Play ACPI device, IDs DLL04b3 SYN0600 SYN0002 PNP0f13 (active)
pnp 00:0a: [io  0x0060]
pnp 00:0a: [io  0x0064]
pnp 00:0a: [io  0x0062]
pnp 00:0a: [io  0x0066]
pnp 00:0a: [irq 1]
pnp 00:0a: Plug and Play ACPI device, IDs PNP0303 (active)
pnp 00:0b: [mem 0xfed1c000-0xfed1ffff]
pnp 00:0b: [mem 0xfed10000-0xfed17fff]
pnp 00:0b: [mem 0xfed18000-0xfed18fff]
pnp 00:0b: [mem 0xfed19000-0xfed19fff]
pnp 00:0b: [mem 0xf8000000-0xfbffffff]
pnp 00:0b: [mem 0xfed20000-0xfed3ffff]
pnp 00:0b: [mem 0xfed90000-0xfed93fff]
pnp 00:0b: [mem 0xfed45000-0xfed8ffff]
pnp 00:0b: [mem 0xff000000-0xffffffff]
pnp 00:0b: [mem 0xfee00000-0xfeefffff]
pnp 00:0b: [mem 0xdfa00000-0xdfa00fff]
system 00:0b: [mem 0xfed1c000-0xfed1ffff] has been reserved
system 00:0b: [mem 0xfed10000-0xfed17fff] has been reserved
system 00:0b: [mem 0xfed18000-0xfed18fff] has been reserved
system 00:0b: [mem 0xfed19000-0xfed19fff] has been reserved
system 00:0b: [mem 0xf8000000-0xfbffffff] has been reserved
system 00:0b: [mem 0xfed20000-0xfed3ffff] has been reserved
system 00:0b: [mem 0xfed90000-0xfed93fff] has been reserved
system 00:0b: [mem 0xfed45000-0xfed8ffff] has been reserved
system 00:0b: [mem 0xff000000-0xffffffff] has been reserved
system 00:0b: [mem 0xfee00000-0xfeefffff] could not be reserved
system 00:0b: [mem 0xdfa00000-0xdfa00fff] has been reserved
system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0c: [irq 20]
pnp 00:0c: Plug and Play ACPI device, IDs SMO8800 (active)
pnp 00:0d: [mem 0x20000000-0x201fffff]
pnp 00:0d: [mem 0x40000000-0x401fffff]
system 00:0d: [mem 0x20000000-0x201fffff] has been reserved
system 00:0d: [mem 0x40000000-0x401fffff] has been reserved
system 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
PCI: max bus depth: 1 pci_try_num: 2
pci 0000:00:1c.0: PCI bridge to [bus 03-04]
pci 0000:00:1c.1: PCI bridge to [bus 05-06]
pci 0000:00:1c.1:   bridge window [io  0xe000-0xefff]
pci 0000:00:1c.1:   bridge window [mem 0xf1100000-0xf11fffff 64bit pref]
pci 0000:00:1c.3: PCI bridge to [bus 09-0a]
pci 0000:00:1c.3:   bridge window [mem 0xf7e00000-0xf7efffff]
pci 0000:00:1c.4: PCI bridge to [bus 0b-0c]
pci 0000:00:1c.4:   bridge window [mem 0xf7d00000-0xf7dfffff]
pci 0000:00:1c.7: PCI bridge to [bus 11-16]
pci 0000:00:1c.7:   bridge window [io  0xc000-0xdfff]
pci 0000:00:1c.7:   bridge window [mem 0xf6c00000-0xf7cfffff]
pci 0000:00:1c.7:   bridge window [mem 0xf0000000-0xf10fffff 64bit pref]
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:00:1c.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
pci 0000:00:1c.7: setting latency timer to 64
pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff]
pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff]
pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff]
pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff]
pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff]
pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff]
pci_bus 0000:00: resource 13 [mem 0xdfa00000-0xfeafffff]
pci_bus 0000:00: resource 14 [mem 0xfed40000-0xfed44fff]
pci_bus 0000:05: resource 0 [io  0xe000-0xefff]
pci_bus 0000:05: resource 2 [mem 0xf1100000-0xf11fffff 64bit pref]
pci_bus 0000:09: resource 1 [mem 0xf7e00000-0xf7efffff]
pci_bus 0000:0b: resource 1 [mem 0xf7d00000-0xf7dfffff]
pci_bus 0000:11: resource 0 [io  0xc000-0xdfff]
pci_bus 0000:11: resource 1 [mem 0xf6c00000-0xf7cfffff]
pci_bus 0000:11: resource 2 [mem 0xf0000000-0xf10fffff 64bit pref]
NET: Registered protocol family 2
IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
UDP hash table entries: 8192 (order: 6, 262144 bytes)
UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
pci 0000:00:02.0: Boot video device
pci 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1a.0: PCI INT A disabled
pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
pci 0000:00:1d.0: PCI INT A disabled
pci 0000:0b:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:0b:00.0: PCI INT A disabled
PCI: CLS 64 bytes, default 64
DMAR: No ATSR found
IOMMU 0 0xfed90000: using Queued invalidation
IOMMU 1 0xfed91000: using Queued invalidation
IOMMU: Setting RMRR:
IOMMU: Setting identity map for device 0000:00:02.0 [0xdb800000 - 0xdf9fffff]
IOMMU: Setting identity map for device 0000:00:1d.0 [0xdad53000 - 0xdad61fff]
IOMMU: Setting identity map for device 0000:00:1a.0 [0xdad53000 - 0xdad61fff]
IOMMU: Prepare 0-16MiB unity mapping for LPC
IOMMU: Setting identity map for device 0000:00:1f.0 [0x0 - 0xffffff]
PCI-DMA: Intel(R) Virtualization Technology for Directed I/O
microcode: CPU0 sig=0x206a7, pf=0x10, revision=0x1b
microcode: CPU1 sig=0x206a7, pf=0x10, revision=0x1b
microcode: CPU2 sig=0x206a7, pf=0x10, revision=0x1b
microcode: CPU3 sig=0x206a7, pf=0x10, revision=0x1b
microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
sha1_ssse3: Using AVX optimized SHA-1 implementation
HugeTLB registered 2 MB page size, pre-allocated 0 pages
DLM installed
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
fuse init (API version 7.17)
msgmni has been set to 32103
NET: Registered protocol family 38
async_tx: api initialized (async)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
pcieport 0000:00:1c.7: setting latency timer to 64
pcieport 0000:00:1c.7: irq 42 for MSI/MSI-X
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp 0000:00:1c.7:pcie04: HPC vendor_id 8086 device_id 1c1e ss_vid 1028 ss_did 4b3
pciehp 0000:00:1c.7:pcie04: service driver pciehp loaded
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
intel_idle: MWAIT substates: 0x21120
intel_idle: v0.4 model 0x2A
intel_idle: lapic_timer_reliable_states 0xffffffff
ACPI: AC Adapter [AC] (off-line)
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0
ACPI: Lid Switch [LID0]
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
ACPI: Power Button [PWRB]
input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
ACPI: Sleep Button [SBTN]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
ACPI: Power Button [PWRF]
thermal LNXTHERM:00: registered as thermal_zone0
ACPI: Thermal Zone [THM] (64 C)
ERST: Table is not found!
GHES: HEST is not enabled!
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
ACPI: Battery Slot [BAT0] (battery present)
Non-volatile memory driver v1.3
i8k: unable to get SMM BIOS version
Dell laptop SMM driver v1.14 21/02/2005 Massimo Dal Zotto (dz@debian.org)
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel Sandybridge Chipset
agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
agpgart-intel 0000:00:00.0: detected 65536K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
ipmi message handler version 39.2
Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using getrawmonotonic().
[drm] Initialized drm 1.1.0 20060810
i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
i915 0000:00:02.0: setting latency timer to 64
mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining
[drm] MTRR allocation failed.  Graphics performance may suffer.
i915 0000:00:02.0: irq 43 for MSI/MSI-X
[drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[drm] Driver supports precise vblank timestamp query.
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
Refined TSC clocksource calibration: 2793.654 MHz.
Switching to clocksource tsc
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 170x48
fb0: inteldrmfb frame buffer device
drm: registered panic notifier
acpi device:34: registered as cooling_device4
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input4
ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
loop: module loaded
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: irq 44 for MSI/MSI-X
ahci: SSS flag set, parallel bus scan disabled
ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x31 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems sxs apst 
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar m2048@0xf7f06000 port 0xf7f06100 irq 44
ata2: DUMMY
ata3: DUMMY
ata4: DUMMY
ata5: SATA max UDMA/133 abar m2048@0xf7f06000 port 0xf7f06300 irq 44
ata6: SATA max UDMA/133 abar m2048@0xf7f06000 port 0xf7f06380 irq 44
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
r8169 0000:05:00.0: setting latency timer to 64
r8169 0000:05:00.0: irq 45 for MSI/MSI-X
r8169 0000:05:00.0: eth0: RTL8168e/8111e at 0xffffc900065d2000, 18:03:73:a0:6f:6a, XID 0c200000 IRQ 45
r8169 0000:05:00.0: eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
VMware vmxnet3 virtual NIC driver - version 1.1.29.0-k-NAPI
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ehci_hcd 0000:00:1a.0: setting latency timer to 64
ehci_hcd 0000:00:1a.0: EHCI Host Controller
ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.0: debug port 2
ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
ehci_hcd 0000:00:1a.0: irq 16, io mem 0xf7f08000
ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 3.2.14-default ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.0: setting latency timer to 64
ehci_hcd 0000:00:1d.0: EHCI Host Controller
ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.0: debug port 2
ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
ehci_hcd 0000:00:1d.0: irq 23, io mem 0xf7f07000
ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 3.2.14-default ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
xhci_hcd 0000:0b:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
xhci_hcd 0000:0b:00.0: setting latency timer to 64
xhci_hcd 0000:0b:00.0: xHCI Host Controller
xhci_hcd 0000:0b:00.0: new USB bus registered, assigned bus number 3
xhci_hcd 0000:0b:00.0: irq 16, io mem 0xf7d00000
xhci_hcd 0000:0b:00.0: irq 46 for MSI/MSI-X
xhci_hcd 0000:0b:00.0: irq 47 for MSI/MSI-X
xhci_hcd 0000:0b:00.0: irq 48 for MSI/MSI-X
xhci_hcd 0000:0b:00.0: irq 49 for MSI/MSI-X
xhci_hcd 0000:0b:00.0: irq 50 for MSI/MSI-X
usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: xHCI Host Controller
usb usb3: Manufacturer: Linux 3.2.14-default xhci_hcd
usb usb3: SerialNumber: 0000:0b:00.0
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
xhci_hcd 0000:0b:00.0: xHCI Host Controller
xhci_hcd 0000:0b:00.0: new USB bus registered, assigned bus number 4
usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: xHCI Host Controller
usb usb4: Manufacturer: Linux 3.2.14-default xhci_hcd
usb usb4: SerialNumber: 0000:0b:00.0
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usbcore: registered new interface driver uas
i8042: PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mousedev: PS/2 mouse device common for all mice
rtc_cmos 00:05: RTC can wake from S4
rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
i2c /dev entries driver
Linux media interface: v0.10
Linux video capture interface: v2.00
gspca_main: v2.14.0 registered
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
coretemp coretemp.0: TjMax is 100 degrees C
coretemp coretemp.0: TjMax is 100 degrees C
coretemp coretemp.0: TjMax is 100 degrees C
i2c-core: driver [max6639] using legacy suspend method
i2c-core: driver [max6639] using legacy resume method
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
iTCO_vendor_support: vendor-support=0
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
device-mapper: dm-log-userspace: version 1.1.0 loaded
Bluetooth: Generic Bluetooth USB driver ver 0.6
usbcore: registered new interface driver btusb
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
mei 0000:00:16.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
mei 0000:00:16.0: setting latency timer to 64
mei 0000:00:16.0: irq 51 for MSI/MSI-X
input: Dell WMI hotkeys as /devices/virtual/input/input6
intel_oaktrail: Platform not recognized (You could try the module's force-parameter)
snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
snd_hda_intel 0000:00:1b.0: irq 52 for MSI/MSI-X
snd_hda_intel 0000:00:1b.0: setting latency timer to 64
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
ata1.00: ATA-8: WDC WD7500BPKT-75PK4T0, 01.01A01, max UDMA/133
ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      WDC WD7500BPKT-7 01.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1465149168 512-byte logical blocks: (750 GB/698 GiB)
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usb 1-1: new high-speed USB device number 2 using ehci_hcd
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
sd 0:0:0:0: [sda] Attached SCSI disk
usb 1-1: New USB device found, idVendor=8087, idProduct=0024
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 6 ports detected
usb 2-1: new high-speed USB device number 2 using ehci_hcd
ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata5.00: ATAPI: PLDS DVD+/-RW DS-8A8SH, KD11, max UDMA/100
ata5.00: configured for UDMA/100
scsi 4:0:0:0: CD-ROM            PLDS     DVD+-RW DS-8A8SH KD11 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
cdrom: Uniform CD-ROM driver Revision: 3.20
sr 4:0:0:0: Attached scsi CD-ROM sr0
sr 4:0:0:0: Attached scsi generic sg1 type 5
usb 2-1: New USB device found, idVendor=8087, idProduct=0024
usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 8 ports detected
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input7
HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
ALSA device list:
  #0: HDA Intel PCH at 0xf7f00000 irq 52
TCP cubic registered
NET: Registered protocol family 17
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
sctp: Hash tables configured (established 65536 bind 65536)
Registering the dns_resolver key type
PM: Checking hibernation image partition /dev/sda6
PM: Hibernation image partition 8:6 present
PM: Looking for hibernation image.
input: PS/2 Generic Mouse as /devices/platform/i8042/serio1/input/input11
usb 1-1.5: new high-speed USB device number 3 using ehci_hcd
PM: Image not found (code -22)
PM: Hibernation image not present or could not be loaded.
registered taskstats version 1
rtc_cmos 00:05: setting system clock to 2012-04-13 16:58:53 UTC (1334336333)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
usb 1-1.5: New USB device found, idVendor=05ca, idProduct=1820
usb 1-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.5: Product: Laptop_Integrated_Webcam_FHD
usb 1-1.5: Manufacturer: CN01MWM9724871A4KB28A00
uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_FHD (05ca:1820)
input: Laptop_Integrated_Webcam_FHD as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5:1.0/input/input12
ata6: SATA link down (SStatus 0 SControl 300)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
usb 2-1.3: new full-speed USB device number 3 using ehci_hcd
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sda5): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) readonly on device 8:5.
devtmpfs: mounted
Freeing unused kernel memory: 620k freed
usb 2-1.3: New USB device found, idVendor=138a, idProduct=0011
usb 2-1.3: New USB device strings: Mfr=0, Product=0, SerialNumber=1
usb 2-1.3: SerialNumber: 56ed5821afe2
usb 2-1.6: new high-speed USB device number 4 using ehci_hcd
usb 2-1.6: New USB device found, idVendor=0bda, idProduct=0138
usb 2-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-1.6: Product: USB2.0-CRW
usb 2-1.6: Manufacturer: Generic
usb 2-1.6: SerialNumber: 20090516388200000
udevd[1837]: starting version 171
i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ACPI: resource 0000:00:1f.3 [io  0xf040-0xf05f] conflicts with ACPI region SMBI [io 0xf040-0xf04f]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
Initializing USB Mass Storage driver...
scsi6 : usb-storage 2-1.6:1.0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:d
Copyright(c) 2003-2011 Intel Corporation
iwlwifi 0000:09:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
iwlwifi 0000:09:00.0: setting latency timer to 64
iwlwifi 0000:09:00.0: pci_resource_len = 0x00002000
iwlwifi 0000:09:00.0: pci_resource_base = ffffc900066b4000
iwlwifi 0000:09:00.0: HW Revision ID = 0x34
iwlwifi 0000:09:00.0: irq 53 for MSI/MSI-X
iwlwifi 0000:09:00.0: Detected Intel(R) Centrino(R) Wireless-N 1030 BGN, REV=0xB0
iwlwifi 0000:09:00.0: L1 Disabled; Enabling L0S
iwlwifi 0000:09:00.0: device EEPROM VER=0x71a, CALIB=0x6
iwlwifi 0000:09:00.0: Device SKU: 0X150
iwlwifi 0000:09:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3
iwlwifi 0000:09:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels
iwlwifi 0000:09:00.0: RF_KILL bit toggled to disable radio.
iwlwifi 0000:09:00.0: loaded firmware version 17.168.5.2 build 35905
Registered led device: phy0-led
ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
scsi 6:0:0:0: Direct-Access     Generic- Multi-Card       1.00 PQ: 0 ANSI: 0 CCS
sd 6:0:0:0: Attached scsi generic sg2 type 0
sd 6:0:0:0: [sdb] Attached SCSI removable disk
EXT3-fs (sda5): using internal journal
Adding 4998972k swap on /dev/sda6.  Priority:-1 extents:1 across:4998972k 
r8169 0000:05:00.0: eth0: unable to load firmware patch rtl_nic/rtl8168e-2.fw (-2)
r8169 0000:05:00.0: eth0: link down
microcode: CPU0 updated to revision 0x25, date = 2011-10-11
microcode: CPU1 updated to revision 0x25, date = 2011-10-11
microcode: CPU2 updated to revision 0x25, date = 2011-10-11
microcode: CPU3 updated to revision 0x25, date = 2011-10-11
pciehp 0000:00:1c.7:pcie04: Card present on Slot(7)
pci 0000:11:00.0: [1b4b:9123] type 0 class 0x000106
pci 0000:11:00.0: reg 10: [io  0x8000-0x8007]
pci 0000:11:00.0: reg 14: [io  0x8040-0x8043]
pci 0000:11:00.0: reg 18: [io  0x8100-0x8107]
pci 0000:11:00.0: reg 1c: [io  0x8140-0x8143]
pci 0000:11:00.0: reg 20: [io  0x800000-0x80000f]
pci 0000:11:00.0: reg 24: [mem 0x00900000-0x009007ff]
pci 0000:11:00.0: reg 30: [mem 0xd0000000-0xd000ffff pref]
pci 0000:11:00.0: PME# supported from D3hot
pci 0000:11:00.0: PME# disabled
pci 0000:11:00.0: BAR 6: assigned [mem 0xf0000000-0xf000ffff pref]
pci 0000:11:00.0: BAR 5: assigned [mem 0xf6c00000-0xf6c007ff]
pci 0000:11:00.0: BAR 5: set to [mem 0xf6c00000-0xf6c007ff] (PCI address [0xf6c00000-0xf6c007ff])
pci 0000:11:00.0: BAR 4: assigned [io  0xc000-0xc00f]
pci 0000:11:00.0: BAR 4: set to [io  0xc000-0xc00f] (PCI address [0xc000-0xc00f])
pci 0000:11:00.0: BAR 0: assigned [io  0xc010-0xc017]
pci 0000:11:00.0: BAR 0: set to [io  0xc010-0xc017] (PCI address [0xc010-0xc017])
pci 0000:11:00.0: BAR 2: assigned [io  0xc018-0xc01f]
pci 0000:11:00.0: BAR 2: set to [io  0xc018-0xc01f] (PCI address [0xc018-0xc01f])
pci 0000:11:00.0: BAR 1: assigned [io  0xc020-0xc023]
pci 0000:11:00.0: BAR 1: set to [io  0xc020-0xc023] (PCI address [0xc020-0xc023])
pci 0000:11:00.0: BAR 3: assigned [io  0xc024-0xc027]
pci 0000:11:00.0: BAR 3: set to [io  0xc024-0xc027] (PCI address [0xc024-0xc027])
pcieport 0000:00:1c.7: PCI bridge to [bus 11-16]
pcieport 0000:00:1c.7:   bridge window [io  0xc000-0xdfff]
pcieport 0000:00:1c.7:   bridge window [mem 0xf6c00000-0xf7cfffff]
pcieport 0000:00:1c.7:   bridge window [mem 0xf0000000-0xf10fffff 64bit pref]
pcieport 0000:00:1c.7: setting latency timer to 64
ahci 0000:11:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ahci 0000:11:00.0: irq 54 for MSI/MSI-X
ahci 0000:11:00.0: controller can do FBS, turning on CAP_FBS
ahci 0000:11:00.0: AHCI 0001.0200 32 slots 8 ports 6 Gbps 0xff impl SATA mode
ahci 0000:11:00.0: flags: 64bit ncq fbs pio 
ahci 0000:11:00.0: setting latency timer to 64
scsi7 : ahci
scsi8 : ahci
scsi9 : ahci
scsi10 : ahci
scsi11 : ahci
scsi12 : ahci
scsi13 : ahci
scsi14 : ahci
ata7: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00100 irq 54
ata8: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00180 irq 54
ata9: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00200 irq 54
ata10: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00280 irq 54
ata11: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00300 irq 54
ata12: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00380 irq 54
ata13: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00400 irq 54
ata14: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00480 irq 54
ata12: SATA link down (SStatus 0 SControl 300)
ata8: SATA link down (SStatus 0 SControl 300)
ata11: SATA link down (SStatus 0 SControl 300)
ata7: SATA link down (SStatus 0 SControl 300)
ata9: SATA link down (SStatus 0 SControl 300)
ata13: SATA link down (SStatus 0 SControl 300)
ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
DRHD: handling fault status reg 2
DMAR:[DMA Read] Request device [11:00.1] fault addr fff00000 
DMAR:[fault reason 02] Present bit in context entry is clear
ata10: SATA link down (SStatus 0 SControl 300)
ata14.00: qc timeout (cmd 0xa1)
ata14.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata14.00: qc timeout (cmd 0xa1)
ata14.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata14: limiting SATA link speed to 1.5 Gbps
ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 310)

[-- Attachment #4: Kouwell_EK-113_linux-3.2.14.txt --]
[-- Type: text/plain, Size: 7871 bytes --]

pciehp 0000:00:1c.7:pcie04: Card present on Slot(7)
pci 0000:11:00.0: [1b4b:9123] type 0 class 0x000106
pci 0000:11:00.0: reg 10: [io  0x8000-0x8007]
pci 0000:11:00.0: reg 14: [io  0x8040-0x8043]
pci 0000:11:00.0: reg 18: [io  0x8100-0x8107]
pci 0000:11:00.0: reg 1c: [io  0x8140-0x8143]
pci 0000:11:00.0: reg 20: [io  0x800000-0x80000f]
pci 0000:11:00.0: reg 24: [mem 0x00900000-0x009007ff]
pci 0000:11:00.0: reg 30: [mem 0xd0000000-0xd000ffff pref]
pci 0000:11:00.0: PME# supported from D3hot
pci 0000:11:00.0: PME# disabled
pci 0000:11:00.0: BAR 6: assigned [mem 0xf0000000-0xf000ffff pref]
pci 0000:11:00.0: BAR 5: assigned [mem 0xf6c00000-0xf6c007ff]
pci 0000:11:00.0: BAR 5: set to [mem 0xf6c00000-0xf6c007ff] (PCI address [0xf6c00000-0xf6c007ff])
pci 0000:11:00.0: BAR 4: assigned [io  0xc000-0xc00f]
pci 0000:11:00.0: BAR 4: set to [io  0xc000-0xc00f] (PCI address [0xc000-0xc00f])
pci 0000:11:00.0: BAR 0: assigned [io  0xc010-0xc017]
pci 0000:11:00.0: BAR 0: set to [io  0xc010-0xc017] (PCI address [0xc010-0xc017])
pci 0000:11:00.0: BAR 2: assigned [io  0xc018-0xc01f]
pci 0000:11:00.0: BAR 2: set to [io  0xc018-0xc01f] (PCI address [0xc018-0xc01f])
pci 0000:11:00.0: BAR 1: assigned [io  0xc020-0xc023]
pci 0000:11:00.0: BAR 1: set to [io  0xc020-0xc023] (PCI address [0xc020-0xc023])
pci 0000:11:00.0: BAR 3: assigned [io  0xc024-0xc027]
pci 0000:11:00.0: BAR 3: set to [io  0xc024-0xc027] (PCI address [0xc024-0xc027])
pcieport 0000:00:1c.7: PCI bridge to [bus 11-16]
pcieport 0000:00:1c.7:   bridge window [io  0xc000-0xdfff]
pcieport 0000:00:1c.7:   bridge window [mem 0xf6c00000-0xf7cfffff]
pcieport 0000:00:1c.7:   bridge window [mem 0xf0000000-0xf10fffff 64bit pref]
pcieport 0000:00:1c.7: setting latency timer to 64
ahci 0000:11:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ahci 0000:11:00.0: irq 54 for MSI/MSI-X
ahci 0000:11:00.0: controller can do FBS, turning on CAP_FBS
ahci 0000:11:00.0: AHCI 0001.0200 32 slots 8 ports 6 Gbps 0xff impl SATA mode
ahci 0000:11:00.0: flags: 64bit ncq fbs pio 
ahci 0000:11:00.0: setting latency timer to 64
scsi8 : ahci
scsi9 : ahci
scsi10 : ahci
scsi11 : ahci
scsi12 : ahci
scsi13 : ahci
scsi14 : ahci
scsi15 : ahci
ata7: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00100 irq 54
ata8: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00180 irq 54
ata9: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00200 irq 54
ata10: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00280 irq 54
ata11: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00300 irq 54
ata12: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00380 irq 54
ata13: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00400 irq 54
ata14: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00480 irq 54
ata11: SATA link down (SStatus 0 SControl 300)
ata13: SATA link down (SStatus 0 SControl 300)
ata9: SATA link down (SStatus 0 SControl 300)
ata10: SATA link down (SStatus 0 SControl 300)
ata7: SATA link down (SStatus 0 SControl 300)
ata12: SATA link down (SStatus 0 SControl 300)
ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata8: SATA link down (SStatus 0 SControl 300)
DRHD: handling fault status reg 2
DMAR:[DMA Read] Request device [11:00.1] fault addr fff00000 
DMAR:[fault reason 02] Present bit in context entry is clear
ata14.00: qc timeout (cmd 0xa1)
ata14.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata14.00: qc timeout (cmd 0xa1)
ata14.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata14: limiting SATA link speed to 1.5 Gbps
ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata14.00: qc timeout (cmd 0xa1)
ata14.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
pciehp 0000:00:1c.7:pcie04: Card not present on Slot(7)
ata7: failed to stop engine (-5)
ata8: failed to stop engine (-5)
ata9: failed to stop engine (-5)
ata10: failed to stop engine (-5)
ata11: failed to stop engine (-5)
ata12: failed to stop engine (-5)
ata13: failed to stop engine (-5)
ata14: failed to stop engine (-5)
ahci 0000:11:00.0: PCI INT A disabled
pciehp 0000:00:1c.7:pcie04: Card present on Slot(7)
pci 0000:11:00.0: [1b4b:9123] type 0 class 0x000106
pci 0000:11:00.0: reg 10: [io  0x8000-0x8007]
pci 0000:11:00.0: reg 14: [io  0x8040-0x8043]
pci 0000:11:00.0: reg 18: [io  0x8100-0x8107]
pci 0000:11:00.0: reg 1c: [io  0x8140-0x8143]
pci 0000:11:00.0: reg 20: [io  0x800000-0x80000f]
pci 0000:11:00.0: reg 24: [mem 0x00900000-0x009007ff]
pci 0000:11:00.0: reg 30: [mem 0xd0000000-0xd000ffff pref]
pci 0000:11:00.0: PME# supported from D3hot
pci 0000:11:00.0: PME# disabled
pci 0000:11:00.0: BAR 6: assigned [mem 0xf0000000-0xf000ffff pref]
pci 0000:11:00.0: BAR 5: assigned [mem 0xf6c00000-0xf6c007ff]
pci 0000:11:00.0: BAR 5: set to [mem 0xf6c00000-0xf6c007ff] (PCI address [0xf6c00000-0xf6c007ff])
pci 0000:11:00.0: BAR 4: assigned [io  0xc000-0xc00f]
pci 0000:11:00.0: BAR 4: set to [io  0xc000-0xc00f] (PCI address [0xc000-0xc00f])
pci 0000:11:00.0: BAR 0: assigned [io  0xc010-0xc017]
pci 0000:11:00.0: BAR 0: set to [io  0xc010-0xc017] (PCI address [0xc010-0xc017])
pci 0000:11:00.0: BAR 2: assigned [io  0xc018-0xc01f]
pci 0000:11:00.0: BAR 2: set to [io  0xc018-0xc01f] (PCI address [0xc018-0xc01f])
pci 0000:11:00.0: BAR 1: assigned [io  0xc020-0xc023]
pci 0000:11:00.0: BAR 1: set to [io  0xc020-0xc023] (PCI address [0xc020-0xc023])
pci 0000:11:00.0: BAR 3: assigned [io  0xc024-0xc027]
pci 0000:11:00.0: BAR 3: set to [io  0xc024-0xc027] (PCI address [0xc024-0xc027])
pcieport 0000:00:1c.7: PCI bridge to [bus 11-16]
pcieport 0000:00:1c.7:   bridge window [io  0xc000-0xdfff]
pcieport 0000:00:1c.7:   bridge window [mem 0xf6c00000-0xf7cfffff]
pcieport 0000:00:1c.7:   bridge window [mem 0xf0000000-0xf10fffff 64bit pref]
pcieport 0000:00:1c.7: setting latency timer to 64
ahci 0000:11:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ahci 0000:11:00.0: irq 54 for MSI/MSI-X
ahci 0000:11:00.0: controller can do FBS, turning on CAP_FBS
ahci 0000:11:00.0: AHCI 0001.0200 32 slots 8 ports 6 Gbps 0xff impl SATA mode
ahci 0000:11:00.0: flags: 64bit ncq fbs pio 
ahci 0000:11:00.0: setting latency timer to 64
scsi16 : ahci
scsi17 : ahci
scsi18 : ahci
scsi19 : ahci
scsi20 : ahci
scsi21 : ahci
scsi22 : ahci
scsi23 : ahci
ata15: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00100 irq 54
ata16: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00180 irq 54
ata17: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00200 irq 54
ata18: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00280 irq 54
ata19: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00300 irq 54
ata20: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00380 irq 54
ata21: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00400 irq 54
ata22: SATA max UDMA/133 abar m2048@0xf6c00000 port 0xf6c00480 irq 54
ata21: SATA link down (SStatus 0 SControl 300)
ata20: SATA link down (SStatus 0 SControl 300)
ata17: SATA link down (SStatus 0 SControl 300)
ata18: SATA link down (SStatus 0 SControl 300)
ata19: SATA link down (SStatus 0 SControl 300)
ata15: SATA link down (SStatus 0 SControl 300)
ata22: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
DRHD: handling fault status reg 2
DMAR:[DMA Read] Request device [11:00.1] fault addr fff00000 
DMAR:[fault reason 02] Present bit in context entry is clear
ata16: SATA link down (SStatus 0 SControl 300)
ata22.00: qc timeout (cmd 0xa1)
ata22.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata22: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata22.00: qc timeout (cmd 0xa1)
ata22.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata22: limiting SATA link speed to 1.5 Gbps
ata22: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata22.00: qc timeout (cmd 0xa1)
ata22.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata22: SATA link up 1.5 Gbps (SStatus 113 SControl 310)

^ permalink raw reply	[flat|nested] 4+ messages in thread
end of thread, other threads:[~2012-04-22  6:22 UTC | newest]

Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-04-13 20:26 3.2.14: Marvell 88SE9123 PCIe SATA 6.0 Gb/s controller not working Martin Mokrejs
2012-04-14 12:39 ` Mark Lord
2012-04-14 12:45   ` Mark Lord
2012-04-22  6:22 ` Robert Hancock

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.