[U-Boot] [PATCH 1/6] imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition

[U-Boot] [PATCH 1/6] imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@freescale.com>

According to include/i2c.h:

"/*
 * Many boards/controllers/drivers don't support an I2C slave interface so
 * provide a default slave address for them for use in common code.  A real
 * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
 * support a slave interface.
 */
#ifndef	CONFIG_SYS_I2C_SLAVE
#define	CONFIG_SYS_I2C_SLAVE	0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
 include/configs/imx31_phycore.h |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)

diff --git a/include/configs/imx31_phycore.h b/include/configs/imx31_phycore.h
index 3153eb5..b3244b9 100644
--- a/include/configs/imx31_phycore.h
+++ b/include/configs/imx31_phycore.h
@@ -56,7 +56,6 @@
 #define CONFIG_I2C_MXC
 #define CONFIG_SYS_I2C_MX31_PORT2
 #define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		0xfe
 
 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE		UART1_BASE
-- 
1.7.1

[U-Boot] [PATCH 2/6] mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@freescale.com>

According to include/i2c.h:

"/*
 * Many boards/controllers/drivers don't support an I2C slave interface so
 * provide a default slave address for them for use in common code.  A real
 * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
 * support a slave interface.
 */
#ifndef	CONFIG_SYS_I2C_SLAVE
#define	CONFIG_SYS_I2C_SLAVE	0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
 include/configs/mx35pdk.h |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)

diff --git a/include/configs/mx35pdk.h b/include/configs/mx35pdk.h
index bd57baa..5f75018 100644
--- a/include/configs/mx35pdk.h
+++ b/include/configs/mx35pdk.h
@@ -59,7 +59,6 @@
 #define CONFIG_I2C_MXC
 #define CONFIG_SYS_I2C_MX35_PORT1
 #define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		0xfe
 #define CONFIG_MXC_SPI
 #define CONFIG_MXC_GPIO
 
-- 
1.7.1

[U-Boot] [PATCH 3/6] mx53ard: Remove CONFIG_SYS_I2C_SLAVE definition

[Fabio Estevam]

According to include/i2c.h:

"/*
 * Many boards/controllers/drivers don't support an I2C slave interface so
 * provide a default slave address for them for use in common code.  A real
 * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
 * support a slave interface.
 */
#ifndef	CONFIG_SYS_I2C_SLAVE
#define	CONFIG_SYS_I2C_SLAVE	0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
 include/configs/mx53ard.h |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)

diff --git a/include/configs/mx53ard.h b/include/configs/mx53ard.h
index f48a41e..f879edc 100644
--- a/include/configs/mx53ard.h
+++ b/include/configs/mx53ard.h
@@ -52,7 +52,6 @@
 #define CONFIG_I2C_MXC
 #define CONFIG_SYS_I2C_MX53_PORT2
 #define CONFIG_SYS_I2C_SPEED            100000
-#define CONFIG_SYS_I2C_SLAVE            0xfe
 
 /* MMC Configs */
 #define CONFIG_FSL_ESDHC
-- 
1.7.1

[U-Boot] [PATCH 4/6] mx53evk: Remove CONFIG_SYS_I2C_SLAVE definition

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@freescale.com>

According to include/i2c.h:

"/*
 * Many boards/controllers/drivers don't support an I2C slave interface so
 * provide a default slave address for them for use in common code.  A real
 * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
 * support a slave interface.
 */
#ifndef	CONFIG_SYS_I2C_SLAVE
#define	CONFIG_SYS_I2C_SLAVE	0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
 include/configs/mx53evk.h |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)

diff --git a/include/configs/mx53evk.h b/include/configs/mx53evk.h
index a77e5b2..2acefe9 100644
--- a/include/configs/mx53evk.h
+++ b/include/configs/mx53evk.h
@@ -55,7 +55,6 @@
 #define CONFIG_I2C_MXC
 #define CONFIG_SYS_I2C_MX53_PORT2       1
 #define CONFIG_SYS_I2C_SPEED            100000
-#define CONFIG_SYS_I2C_SLAVE            0xfe
 
 /* PMIC Configs */
 #define CONFIG_PMIC
-- 
1.7.1

[U-Boot] [PATCH 5/6] mx53loco: Remove CONFIG_SYS_I2C_SLAVE definition

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@freescale.com>

According to include/i2c.h:

"/*
 * Many boards/controllers/drivers don't support an I2C slave interface so
 * provide a default slave address for them for use in common code.  A real
 * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
 * support a slave interface.
 */
#ifndef	CONFIG_SYS_I2C_SLAVE
#define	CONFIG_SYS_I2C_SLAVE	0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
 include/configs/mx53loco.h |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)

diff --git a/include/configs/mx53loco.h b/include/configs/mx53loco.h
index 7d782e2..7c45647 100644
--- a/include/configs/mx53loco.h
+++ b/include/configs/mx53loco.h
@@ -92,7 +92,6 @@
 #define CONFIG_I2C_MXC
 #define CONFIG_SYS_I2C_MX53_PORT1
 #define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		0xfe
 
 /* PMIC Controller */
 #define CONFIG_PMIC
-- 
1.7.1

[U-Boot] [PATCH 6/6] mx53smd: Remove CONFIG_SYS_I2C_SLAVE definition

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@freescale.com>

According to include/i2c.h:

"/*
 * Many boards/controllers/drivers don't support an I2C slave interface so
 * provide a default slave address for them for use in common code.  A real
 * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
 * support a slave interface.
 */
#ifndef	CONFIG_SYS_I2C_SLAVE
#define	CONFIG_SYS_I2C_SLAVE	0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
 include/configs/mx53smd.h |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)

diff --git a/include/configs/mx53smd.h b/include/configs/mx53smd.h
index a04db3f..61edd7f 100644
--- a/include/configs/mx53smd.h
+++ b/include/configs/mx53smd.h
@@ -52,7 +52,6 @@
 #define CONFIG_I2C_MXC
 #define CONFIG_SYS_I2C_MX53_PORT2
 #define CONFIG_SYS_I2C_SPEED            100000
-#define CONFIG_SYS_I2C_SLAVE            0xfe
 
 /* MMC Configs */
 #define CONFIG_FSL_ESDHC
-- 
1.7.1

[U-Boot] [PATCH 1/6] imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition

[Stefano Babic]

On 03/06/2012 09:53, Fabio Estevam wrote:
> From: Fabio Estevam <fabio.estevam@freescale.com>
> 
> According to include/i2c.h:
> 
> "/*
>  * Many boards/controllers/drivers don't support an I2C slave interface so
>  * provide a default slave address for them for use in common code.  A real
>  * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
>  * support a slave interface.
>  */
> #ifndef	CONFIG_SYS_I2C_SLAVE
> #define	CONFIG_SYS_I2C_SLAVE	0xfe
> #endif

Whole series applied to u-boot-imx, thanks.

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================