* [PATCH 0/6] Introduce the SC8180x devices
@ 2022-09-16 12:11 Vinod Koul
2022-09-16 12:11 ` [PATCH 1/6] dt-bindings: firmware: document Qualcomm SC8180x SCM Vinod Koul
` (5 more replies)
0 siblings, 6 replies; 14+ messages in thread
From: Vinod Koul @ 2022-09-16 12:11 UTC (permalink / raw)
To: Bjorn Andersson, Martin K . Petersen, Greg Kroah-Hartman
Cc: linux-arm-msm, Vinod Koul, Rob Herring, Krzysztof Kozlowski,
devicetree, linux-kernel, Alim Akhtar, Avri Altman,
Bart Van Assche, linux-scsi, Wesley Cheng, linux-usb
This add Qualcomm SC8180x SoC which features in Lenovo Flex 5G laptop. This
also adds support for Primus platform as well as Lenovo Flex 5G laptop.
I would be great if Martin and Greg can ack the binding patch so that
everything can go thru qcom tree
Bjorn Andersson (3):
arm64: dts: qcom: Introduce the SC8180x platform
arm64: dts: qcom: sc8180x: Introduce Primus
arm64: dts: qcom: sc8180x: Introduce Lenovo Flex 5G
Vinod Koul (3):
dt-bindings: firmware: document Qualcomm SC8180x SCM
scsi: ufs: dt-bindings: Add SC8180x binding
dt-bindings: usb: qcom,dwc3: Add SC8180x binding
.../bindings/firmware/qcom,scm.yaml | 1 +
.../devicetree/bindings/ufs/qcom,ufs.yaml | 1 +
.../devicetree/bindings/usb/qcom,dwc3.yaml | 1 +
arch/arm64/boot/dts/qcom/Makefile | 2 +
.../boot/dts/qcom/sc8180x-lenovo-flex-5g.dts | 590 +++
arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi | 326 ++
arch/arm64/boot/dts/qcom/sc8180x-primus.dts | 706 +++
arch/arm64/boot/dts/qcom/sc8180x.dtsi | 3939 +++++++++++++++++
8 files changed, 5566 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts
create mode 100644 arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/sc8180x-primus.dts
create mode 100644 arch/arm64/boot/dts/qcom/sc8180x.dtsi
--
2.37.3
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 1/6] dt-bindings: firmware: document Qualcomm SC8180x SCM
2022-09-16 12:11 [PATCH 0/6] Introduce the SC8180x devices Vinod Koul
@ 2022-09-16 12:11 ` Vinod Koul
2022-09-17 16:29 ` Krzysztof Kozlowski
2022-09-16 12:12 ` [PATCH 2/6] scsi: ufs: dt-bindings: Add SC8180x binding Vinod Koul
` (4 subsequent siblings)
5 siblings, 1 reply; 14+ messages in thread
From: Vinod Koul @ 2022-09-16 12:11 UTC (permalink / raw)
To: Bjorn Andersson
Cc: linux-arm-msm, Vinod Koul, Rob Herring, Krzysztof Kozlowski,
devicetree, linux-kernel
Document the compatible for Qualcomm SC8180x SCM
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
Documentation/devicetree/bindings/firmware/qcom,scm.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
index c5b76c9f7ad0..a8a14da54e53 100644
--- a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
+++ b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
@@ -40,6 +40,7 @@ properties:
- qcom,scm-msm8998
- qcom,scm-sc7180
- qcom,scm-sc7280
+ - qcom,scm-sc8180x
- qcom,scm-sc8280xp
- qcom,scm-sdm845
- qcom,scm-sdx55
--
2.37.3
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 2/6] scsi: ufs: dt-bindings: Add SC8180x binding
2022-09-16 12:11 [PATCH 0/6] Introduce the SC8180x devices Vinod Koul
2022-09-16 12:11 ` [PATCH 1/6] dt-bindings: firmware: document Qualcomm SC8180x SCM Vinod Koul
@ 2022-09-16 12:12 ` Vinod Koul
2022-09-16 12:36 ` Johan Hovold
2022-09-16 12:12 ` [PATCH 3/6] dt-bindings: usb: qcom,dwc3: " Vinod Koul
` (3 subsequent siblings)
5 siblings, 1 reply; 14+ messages in thread
From: Vinod Koul @ 2022-09-16 12:12 UTC (permalink / raw)
To: Martin K . Petersen, Bjorn Andersson
Cc: linux-arm-msm, Vinod Koul, Alim Akhtar, Avri Altman,
Bart Van Assche, linux-scsi, Rob Herring, Krzysztof Kozlowski,
devicetree, linux-kernel
Document the UFS HC for SC8180x SoC
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
Documentation/devicetree/bindings/ufs/qcom,ufs.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/ufs/qcom,ufs.yaml b/Documentation/devicetree/bindings/ufs/qcom,ufs.yaml
index f2d6298d926c..dd0256357247 100644
--- a/Documentation/devicetree/bindings/ufs/qcom,ufs.yaml
+++ b/Documentation/devicetree/bindings/ufs/qcom,ufs.yaml
@@ -26,6 +26,7 @@ properties:
- qcom,msm8994-ufshc
- qcom,msm8996-ufshc
- qcom,msm8998-ufshc
+ - qcom,sc8180x-ufshc
- qcom,sc8280xp-ufshc
- qcom,sdm845-ufshc
- qcom,sm6350-ufshc
--
2.37.3
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 3/6] dt-bindings: usb: qcom,dwc3: Add SC8180x binding
2022-09-16 12:11 [PATCH 0/6] Introduce the SC8180x devices Vinod Koul
2022-09-16 12:11 ` [PATCH 1/6] dt-bindings: firmware: document Qualcomm SC8180x SCM Vinod Koul
2022-09-16 12:12 ` [PATCH 2/6] scsi: ufs: dt-bindings: Add SC8180x binding Vinod Koul
@ 2022-09-16 12:12 ` Vinod Koul
2022-09-16 12:33 ` Johan Hovold
2022-09-16 12:12 ` [PATCH 4/6] arm64: dts: qcom: Introduce the SC8180x platform Vinod Koul
` (2 subsequent siblings)
5 siblings, 1 reply; 14+ messages in thread
From: Vinod Koul @ 2022-09-16 12:12 UTC (permalink / raw)
To: Greg Kroah-Hartman, Bjorn Andersson
Cc: linux-arm-msm, Vinod Koul, Wesley Cheng, linux-usb, Rob Herring,
Krzysztof Kozlowski, devicetree, linux-kernel
Document the USB dwc3 controller for SC8180x SoC
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
Documentation/devicetree/bindings/usb/qcom,dwc3.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
index fea3e7092ace..f33735f3702d 100644
--- a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
+++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
@@ -24,6 +24,7 @@ properties:
- qcom,qcs404-dwc3
- qcom,sc7180-dwc3
- qcom,sc7280-dwc3
+ - qcom,sc8180x-dwc3
- qcom,sc8280xp-dwc3
- qcom,sdm660-dwc3
- qcom,sdm845-dwc3
--
2.37.3
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 4/6] arm64: dts: qcom: Introduce the SC8180x platform
2022-09-16 12:11 [PATCH 0/6] Introduce the SC8180x devices Vinod Koul
` (2 preceding siblings ...)
2022-09-16 12:12 ` [PATCH 3/6] dt-bindings: usb: qcom,dwc3: " Vinod Koul
@ 2022-09-16 12:12 ` Vinod Koul
2022-09-16 12:12 ` [PATCH 5/6] arm64: dts: qcom: sc8180x: Introduce Primus Vinod Koul
2022-09-16 12:12 ` [PATCH 6/6] arm64: dts: qcom: sc8180x: Introduce Lenovo Flex 5G Vinod Koul
5 siblings, 0 replies; 14+ messages in thread
From: Vinod Koul @ 2022-09-16 12:12 UTC (permalink / raw)
To: Bjorn Andersson
Cc: linux-arm-msm, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
devicetree, linux-kernel, Vinod Koul
From: Bjorn Andersson <bjorn.andersson@linaro.org>
Introduce a base dtsi for the Qualcomm SC8180x platform, with CPUs,
global clock controller, SMMU, rpmh clocks, rpmh power-domains, CPUfreq,
QUP blocks, UFS, USB, ADSP, CDSP and MPSS and WiFi.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sc8180x.dtsi | 3939 +++++++++++++++++++++++++
1 file changed, 3939 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sc8180x.dtsi
diff --git a/arch/arm64/boot/dts/qcom/sc8180x.dtsi b/arch/arm64/boot/dts/qcom/sc8180x.dtsi
new file mode 100644
index 000000000000..91f1edf83651
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc8180x.dtsi
@@ -0,0 +1,3939 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020-2022, Linaro Limited
+ */
+
+#include <dt-bindings/clock/qcom,dispcc-sm8250.h>
+#include <dt-bindings/clock/qcom,gcc-sc8180x.h>
+#include <dt-bindings/clock/qcom,gpucc-sm8150.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/interconnect/qcom,osm-l3.h>
+#include <dt-bindings/interconnect/qcom,sc8180x.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ interrupt-parent = <&intc>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clocks {
+ xo_board_clk: xo-board {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <38400000>;
+ };
+
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32764>;
+ clock-output-names = "sleep_clk";
+ };
+ };
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ CPU0: cpu@0 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <602>;
+ next-level-cache = <&L2_0>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
+ operating-points-v2 = <&cpu0_opp_table>;
+ interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>,
+ <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
+ power-domains = <&CPU_PD0>;
+ power-domain-names = "psci";
+ #cooling-cells = <2>;
+ L2_0: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ L3_0: l3-cache {
+ compatible = "cache";
+ };
+ };
+ };
+
+ CPU1: cpu@100 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <602>;
+ next-level-cache = <&L2_100>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
+ operating-points-v2 = <&cpu0_opp_table>;
+ interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>,
+ <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
+ power-domains = <&CPU_PD1>;
+ power-domain-names = "psci";
+ #cooling-cells = <2>;
+ L2_100: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+
+ };
+
+ CPU2: cpu@200 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x200>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <602>;
+ next-level-cache = <&L2_200>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
+ operating-points-v2 = <&cpu0_opp_table>;
+ interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>,
+ <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
+ power-domains = <&CPU_PD2>;
+ power-domain-names = "psci";
+ #cooling-cells = <2>;
+ L2_200: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU3: cpu@300 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x300>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <602>;
+ next-level-cache = <&L2_300>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
+ operating-points-v2 = <&cpu0_opp_table>;
+ interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>,
+ <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
+ power-domains = <&CPU_PD3>;
+ power-domain-names = "psci";
+ #cooling-cells = <2>;
+ L2_300: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU4: cpu@400 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x400>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
+ next-level-cache = <&L2_400>;
+ qcom,freq-domain = <&cpufreq_hw 1>;
+ operating-points-v2 = <&cpu4_opp_table>;
+ interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>,
+ <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
+ power-domains = <&CPU_PD4>;
+ power-domain-names = "psci";
+ #cooling-cells = <2>;
+ L2_400: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU5: cpu@500 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x500>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
+ next-level-cache = <&L2_500>;
+ qcom,freq-domain = <&cpufreq_hw 1>;
+ operating-points-v2 = <&cpu4_opp_table>;
+ interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>,
+ <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
+ power-domains = <&CPU_PD5>;
+ power-domain-names = "psci";
+ #cooling-cells = <2>;
+ L2_500: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU6: cpu@600 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x600>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
+ next-level-cache = <&L2_600>;
+ qcom,freq-domain = <&cpufreq_hw 1>;
+ operating-points-v2 = <&cpu4_opp_table>;
+ interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>,
+ <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
+ power-domains = <&CPU_PD6>;
+ power-domain-names = "psci";
+ #cooling-cells = <2>;
+ L2_600: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU7: cpu@700 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x700>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
+ next-level-cache = <&L2_700>;
+ qcom,freq-domain = <&cpufreq_hw 1>;
+ operating-points-v2 = <&cpu4_opp_table>;
+ interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>,
+ <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
+ power-domains = <&CPU_PD7>;
+ power-domain-names = "psci";
+ #cooling-cells = <2>;
+ L2_700: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&CPU0>;
+ };
+
+ core1 {
+ cpu = <&CPU1>;
+ };
+
+ core2 {
+ cpu = <&CPU2>;
+ };
+
+ core3 {
+ cpu = <&CPU3>;
+ };
+
+ core4 {
+ cpu = <&CPU4>;
+ };
+
+ core5 {
+ cpu = <&CPU5>;
+ };
+
+ core6 {
+ cpu = <&CPU6>;
+ };
+
+ core7 {
+ cpu = <&CPU7>;
+ };
+ };
+ };
+
+ idle-states {
+ entry-method = "psci";
+
+ LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
+ compatible = "arm,idle-state";
+ idle-state-name = "little-rail-power-collapse";
+ arm,psci-suspend-param = <0x40000004>;
+ entry-latency-us = <355>;
+ exit-latency-us = <909>;
+ min-residency-us = <3934>;
+ local-timer-stop;
+ };
+
+ BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
+ compatible = "arm,idle-state";
+ idle-state-name = "big-rail-power-collapse";
+ arm,psci-suspend-param = <0x40000004>;
+ entry-latency-us = <241>;
+ exit-latency-us = <1461>;
+ min-residency-us = <4488>;
+ local-timer-stop;
+ };
+ };
+
+ domain-idle-states {
+ CLUSTER_SLEEP_0: cluster-sleep-0 {
+ compatible = "domain-idle-state";
+ idle-state-name = "cluster-power-collapse";
+ arm,psci-suspend-param = <0x4100c244>;
+ entry-latency-us = <3263>;
+ exit-latency-us = <6562>;
+ min-residency-us = <9987>;
+ };
+ };
+ };
+
+ cpu0_opp_table: opp-table-cpu0 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ opp-peak-kBps = <800000 9600000>;
+ };
+
+ opp-422400000 {
+ opp-hz = /bits/ 64 <422400000>;
+ opp-peak-kBps = <800000 9600000>;
+ };
+
+ opp-537600000 {
+ opp-hz = /bits/ 64 <537600000>;
+ opp-peak-kBps = <800000 12902400>;
+ };
+
+ opp-652800000 {
+ opp-hz = /bits/ 64 <652800000>;
+ opp-peak-kBps = <800000 12902400>;
+ };
+
+ opp-768000000 {
+ opp-hz = /bits/ 64 <768000000>;
+ opp-peak-kBps = <800000 15974400>;
+ };
+
+ opp-883200000 {
+ opp-hz = /bits/ 64 <883200000>;
+ opp-peak-kBps = <1804000 19660800>;
+ };
+
+ opp-998400000 {
+ opp-hz = /bits/ 64 <998400000>;
+ opp-peak-kBps = <1804000 19660800>;
+ };
+
+ opp-1113600000 {
+ opp-hz = /bits/ 64 <1113600000>;
+ opp-peak-kBps = <1804000 22732800>;
+ };
+
+ opp-1228800000 {
+ opp-hz = /bits/ 64 <1228800000>;
+ opp-peak-kBps = <1804000 22732800>;
+ };
+
+ opp-1363200000 {
+ opp-hz = /bits/ 64 <1363200000>;
+ opp-peak-kBps = <2188000 25804800>;
+ };
+
+ opp-1478400000 {
+ opp-hz = /bits/ 64 <1478400000>;
+ opp-peak-kBps = <2188000 31948800>;
+ };
+
+ opp-1574400000 {
+ opp-hz = /bits/ 64 <1574400000>;
+ opp-peak-kBps = <3072000 31948800>;
+ };
+
+ opp-1670400000 {
+ opp-hz = /bits/ 64 <1670400000>;
+ opp-peak-kBps = <3072000 31948800>;
+ };
+
+ opp-1766400000 {
+ opp-hz = /bits/ 64 <1766400000>;
+ opp-peak-kBps = <3072000 31948800>;
+ };
+ };
+
+ cpu4_opp_table: opp-table-cpu4 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-825600000 {
+ opp-hz = /bits/ 64 <825600000>;
+ opp-peak-kBps = <1804000 15974400>;
+ };
+
+ opp-940800000 {
+ opp-hz = /bits/ 64 <940800000>;
+ opp-peak-kBps = <2188000 19660800>;
+ };
+
+ opp-1056000000 {
+ opp-hz = /bits/ 64 <1056000000>;
+ opp-peak-kBps = <2188000 22732800>;
+ };
+
+ opp-1171200000 {
+ opp-hz = /bits/ 64 <1171200000>;
+ opp-peak-kBps = <3072000 25804800>;
+ };
+
+ opp-1286400000 {
+ opp-hz = /bits/ 64 <1286400000>;
+ opp-peak-kBps = <3072000 31948800>;
+ };
+
+ opp-1420800000 {
+ opp-hz = /bits/ 64 <1420800000>;
+ opp-peak-kBps = <4068000 31948800>;
+ };
+
+ opp-1536000000 {
+ opp-hz = /bits/ 64 <1536000000>;
+ opp-peak-kBps = <4068000 31948800>;
+ };
+
+ opp-1651200000 {
+ opp-hz = /bits/ 64 <1651200000>;
+ opp-peak-kBps = <4068000 40550400>;
+ };
+
+ opp-1766400000 {
+ opp-hz = /bits/ 64 <1766400000>;
+ opp-peak-kBps = <4068000 40550400>;
+ };
+
+ opp-1881600000 {
+ opp-hz = /bits/ 64 <1881600000>;
+ opp-peak-kBps = <4068000 43008000>;
+ };
+
+ opp-1996800000 {
+ opp-hz = /bits/ 64 <1996800000>;
+ opp-peak-kBps = <6220000 43008000>;
+ };
+
+ opp-2131200000 {
+ opp-hz = /bits/ 64 <2131200000>;
+ opp-peak-kBps = <6220000 49152000>;
+ };
+
+ opp-2246400000 {
+ opp-hz = /bits/ 64 <2246400000>;
+ opp-peak-kBps = <7216000 49152000>;
+ };
+
+ opp-2361600000 {
+ opp-hz = /bits/ 64 <2361600000>;
+ opp-peak-kBps = <8368000 49152000>;
+ };
+
+ opp-2457600000 {
+ opp-hz = /bits/ 64 <2457600000>;
+ opp-peak-kBps = <8368000 51609600>;
+ };
+
+ opp-2553600000 {
+ opp-hz = /bits/ 64 <2553600000>;
+ opp-peak-kBps = <8368000 51609600>;
+ };
+
+ opp-2649600000 {
+ opp-hz = /bits/ 64 <2649600000>;
+ opp-peak-kBps = <8368000 51609600>;
+ };
+
+ opp-2745600000 {
+ opp-hz = /bits/ 64 <2745600000>;
+ opp-peak-kBps = <8368000 51609600>;
+ };
+
+ opp-2841600000 {
+ opp-hz = /bits/ 64 <2841600000>;
+ opp-peak-kBps = <8368000 51609600>;
+ };
+
+ opp-2918400000 {
+ opp-hz = /bits/ 64 <2918400000>;
+ opp-peak-kBps = <8368000 51609600>;
+ };
+
+ opp-2995200000 {
+ opp-hz = /bits/ 64 <2995200000>;
+ opp-peak-kBps = <8368000 51609600>;
+ };
+ };
+
+ firmware {
+ scm: scm {
+ compatible = "qcom,scm-sc8180x", "qcom,scm";
+ };
+ };
+
+ camnoc_virt: interconnect-camnoc-virt {
+ compatible = "qcom,sc8180x-camnoc-virt";
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ mc_virt: interconnect-mc-virt {
+ compatible = "qcom,sc8180x-mc-virt";
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ qup_virt: interconnect-qup-virt {
+ compatible = "qcom,sc8180x-qup-virt";
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ /* We expect the bootloader to fill in the size */
+ reg = <0x0 0x80000000 0x0 0x0>;
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <GIC_PPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+
+ CPU_PD0: cpu0 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+ };
+
+ CPU_PD1: cpu1 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+ };
+
+ CPU_PD2: cpu2 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+ };
+
+ CPU_PD3: cpu3 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+ };
+
+ CPU_PD4: cpu4 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&BIG_CPU_SLEEP_0>;
+ };
+
+ CPU_PD5: cpu5 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&BIG_CPU_SLEEP_0>;
+ };
+
+ CPU_PD6: cpu6 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&BIG_CPU_SLEEP_0>;
+ };
+
+ CPU_PD7: cpu7 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&BIG_CPU_SLEEP_0>;
+ };
+
+ CLUSTER_PD: cpu-cluster0 {
+ #power-domain-cells = <0>;
+ domain-idle-states = <&CLUSTER_SLEEP_0>;
+ };
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ hyp_mem: hyp-region@85700000 {
+ reg = <0x0 0x85700000 0x0 0x600000>;
+ no-map;
+ };
+
+ xbl_mem: xbl-region@85d00000 {
+ reg = <0x0 0x85d00000 0x0 0x140000>;
+ no-map;
+ };
+
+ aop_mem: aop-region@85f00000 {
+ reg = <0x0 0x85f00000 0x0 0x20000>;
+ no-map;
+ };
+
+ aop_cmd_db: cmd-db-region@85f20000 {
+ compatible = "qcom,cmd-db";
+ reg = <0x0 0x85f20000 0x0 0x20000>;
+ no-map;
+ };
+
+ reserved-region@85f40000 {
+ reg = <0x0 0x85f40000 0x0 0x10000>;
+ no-map;
+ };
+
+ smem_mem: smem-region@86000000 {
+ compatible = "qcom,smem";
+ reg = <0x0 0x86000000 0x0 0x200000>;
+ no-map;
+ hwlocks = <&tcsr_mutex 3>;
+ };
+
+ reserved-region@86200000 {
+ reg = <0x0 0x86200000 0x0 0x3900000>;
+ no-map;
+ };
+
+ reserved-region@89b00000 {
+ reg = <0x0 0x89b00000 0x0 0x1c00000>;
+ no-map;
+ };
+
+ reserved-region@9d400000 {
+ reg = <0x0 0x9d400000 0x0 0x1000000>;
+ no-map;
+ };
+
+ reserved-region@9e400000 {
+ reg = <0x0 0x9e400000 0x0 0x1400000>;
+ no-map;
+ };
+
+ reserved-region@9f800000 {
+ reg = <0x0 0x9f800000 0x0 0x800000>;
+ no-map;
+ };
+ };
+
+ smp2p-cdsp {
+ compatible = "qcom,smp2p";
+ qcom,smem = <94>, <432>;
+
+ interrupts = <GIC_SPI 576 IRQ_TYPE_EDGE_RISING>;
+
+ mboxes = <&apss_shared 6>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <5>;
+
+ cdsp_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ cdsp_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ smp2p-lpass {
+ compatible = "qcom,smp2p";
+ qcom,smem = <443>, <429>;
+
+ interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;
+
+ mboxes = <&apss_shared 10>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <2>;
+
+ adsp_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ adsp_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ smp2p-mpss {
+ compatible = "qcom,smp2p";
+ qcom,smem = <435>, <428>;
+
+ interrupts = <GIC_SPI 451 IRQ_TYPE_EDGE_RISING>;
+
+ mboxes = <&apss_shared 14>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <1>;
+
+ modem_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ modem_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ modem_smp2p_ipa_out: ipa-out {
+ qcom,entry-name = "ipa";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ modem_smp2p_ipa_in: ipa-in {
+ qcom,entry-name = "ipa";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ modem_smp2p_wlan_in: wlan {
+ qcom,entry-name = "wlan";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ smp2p-slpi {
+ compatible = "qcom,smp2p";
+ qcom,smem = <481>, <430>;
+
+ interrupts = <GIC_SPI 172 IRQ_TYPE_EDGE_RISING>;
+
+ mboxes = <&apss_shared 26>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <3>;
+
+ slpi_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ slpi_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ soc: soc@0 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0 0 0 0 0x10 0>;
+ dma-ranges = <0 0 0 0 0x10 0>;
+ compatible = "simple-bus";
+
+ gcc: clock-controller@100000 {
+ compatible = "qcom,gcc-sc8180x";
+ reg = <0x0 0x00100000 0x0 0x1f0000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ clock-names = "bi_tcxo",
+ "bi_tcxo_ao",
+ "sleep_clk";
+ clocks = <&rpmhcc RPMH_CXO_CLK>,
+ <&rpmhcc RPMH_CXO_CLK_A>,
+ <&sleep_clk>;
+ };
+
+ qupv3_id_0: geniqup@8c0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0 0x008c0000 0 0x6000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ iommus = <&apps_smmu 0x4c3 0>;
+ status = "disabled";
+
+ i2c0: i2c@880000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00880000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi0: spi@880000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00880000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart0: serial@880000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00880000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c1: i2c@884000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00884000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi1: spi@884000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00884000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart1: serial@884000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00884000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c2: i2c@888000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00888000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi2: spi@888000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00888000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart2: serial@888000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00888000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c3: i2c@88c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x0088c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi3: spi@88c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x0088c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart3: serial@88c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x0088c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c4: i2c@890000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00890000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi4: spi@890000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00890000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart4: serial@890000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00890000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c5: i2c@894000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00894000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi5: spi@894000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00894000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart5: serial@894000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00894000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c6: i2c@898000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00898000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi6: spi@898000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00898000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart6: serial@898000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00898000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c7: i2c@89c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x0089c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi7: spi@89c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x0089c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart7: serial@89c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x0089c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+ };
+
+ qupv3_id_1: geniqup@ac0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0x0 0x00ac0000 0x0 0x6000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ iommus = <&apps_smmu 0x603 0>;
+ status = "disabled";
+
+ i2c8: i2c@a80000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi8: spi@a80000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart8: serial@a80000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c9: i2c@a84000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi9: spi@a84000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart9: serial@a84000 {
+ compatible = "qcom,geni-debug-uart";
+ reg = <0 0x00a84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c10: i2c@a88000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi10: spi@a88000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart10: serial@a88000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c11: i2c@a8c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi11: spi@a8c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart11: serial@a8c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c12: i2c@a90000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi12: spi@a90000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart12: serial@a90000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c16: i2c@a94000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi16: spi@a94000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart16: serial@a94000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+ };
+
+ qupv3_id_2: geniqup@cc0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0x0 0x00cc0000 0x0 0x6000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ iommus = <&apps_smmu 0x7a3 0>;
+ status = "disabled";
+
+ i2c17: i2c@c80000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00c80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
+ interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>,
+ <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi17: spi@c80000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00c80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
+ interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart17: serial@c80000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00c80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
+ interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c18: i2c@c84000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00c84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+ interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>,
+ <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi18: spi@c84000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00c84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+ interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart18: serial@c84000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00c84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+ interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c19: i2c@c88000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00c88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
+ interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>,
+ <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi19: spi@c88000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00c88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
+ interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart19: serial@c88000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00c88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
+ interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c13: i2c@c8c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00c8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+ interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>,
+ <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi13: spi@c8c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00c8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+ interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart13: serial@c8c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00c8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+ interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c14: i2c@c90000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00c90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+ interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>,
+ <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi14: spi@c90000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00c90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+ interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart14: serial@c90000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00c90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+ interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c15: i2c@c94000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00c94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+ interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>,
+ <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi15: spi@c94000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00c94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+ interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
+ interconnect-names = "qup-core", "qup-config";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart15: serial@c94000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00c94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+ interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+ };
+
+ config_noc: interconnect@1500000 {
+ compatible = "qcom,sc8180x-config-noc";
+ reg = <0 0x01500000 0 0x7400>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ system_noc: interconnect@1620000 {
+ compatible = "qcom,sc8180x-system-noc";
+ reg = <0 0x01620000 0 0x19400>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ aggre1_noc: interconnect@16e0000 {
+ compatible = "qcom,sc8180x-aggre1-noc";
+ reg = <0 0x016e0000 0 0xd080>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ aggre2_noc: interconnect@1700000 {
+ compatible = "qcom,sc8180x-aggre2-noc";
+ reg = <0 0x01700000 0 0x20000>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ compute_noc: interconnect@1720000 {
+ compatible = "qcom,sc8180x-compute-noc";
+ reg = <0 0x01720000 0 0x7000>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ mmss_noc: interconnect@1740000 {
+ compatible = "qcom,sc8180x-mmss-noc";
+ reg = <0 0x01740000 0 0x1c100>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ pcie0: pci@1c00000 {
+ compatible = "qcom,pcie-sc8180x", "snps,dw-pcie";
+ reg = <0 0x01c00000 0 0x3000>,
+ <0 0x60000000 0 0xf1d>,
+ <0 0x60000f20 0 0xa8>,
+ <0 0x60001000 0 0x1000>,
+ <0 0x60100000 0 0x100000>;
+ reg-names = "parf", "dbi", "elbi", "atu", "config";
+ device_type = "pci";
+ linux,pci-domain = <0>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <2>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x01000000 0x0 0x60200000 0x0 0x60200000 0x0 0x100000>,
+ <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0x3d00000>;
+
+ interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
+ <&gcc GCC_PCIE_0_AUX_CLK>,
+ <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
+ <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
+ <&gcc GCC_PCIE_0_CLKREF_CLK>,
+ <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
+ clock-names = "pipe",
+ "aux",
+ "cfg",
+ "bus_master",
+ "bus_slave",
+ "slave_q2a",
+ "ref",
+ "tbu";
+
+ assigned-clocks = <&gcc GCC_PCIE_0_AUX_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ iommus = <&apps_smmu 0x1d80 0x7f>;
+ iommu-map = <0x0 &apps_smmu 0x1d80 0x1>,
+ <0x100 &apps_smmu 0x1d81 0x1>;
+
+ resets = <&gcc GCC_PCIE_0_BCR>;
+ reset-names = "pci";
+
+ power-domains = <&gcc PCIE_0_GDSC>;
+
+ phys = <&pcie0_lane>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
+
+ pcie0_phy: phy@1c06000 {
+ compatible = "qcom,sc8180x-qmp-pcie-phy";
+ reg = <0 0x1c06000 0 0x1c0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+ <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_0_CLKREF_CLK>,
+ <&gcc GCC_PCIE1_PHY_REFGEN_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+ resets = <&gcc GCC_PCIE_0_PHY_BCR>;
+ reset-names = "phy";
+
+ assigned-clocks = <&gcc GCC_PCIE0_PHY_REFGEN_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ status = "disabled";
+
+ pcie0_lane: lanes@1c06200 {
+ reg = <0 0x1c06200 0 0x170>, /* tx0 */
+ <0 0x1c06400 0 0x200>, /* rx0 */
+ <0 0x1c06a00 0 0x1f0>, /* pcs */
+ <0 0x1c06600 0 0x170>, /* tx1 */
+ <0 0x1c06800 0 0x200>, /* rx1 */
+ <0 0x1c06e00 0 0xf4>; /* pcs_com */
+ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+ clock-names = "pipe0";
+
+ #phy-cells = <0>;
+ clock-output-names = "pcie_0_pipe_clk";
+ };
+ };
+
+ pcie3: pci@1c08000 {
+ compatible = "qcom,pcie-sc8180x", "snps,dw-pcie";
+ reg = <0 0x01c08000 0 0x3000>,
+ <0 0x40000000 0 0xf1d>,
+ <0 0x40000f20 0 0xa8>,
+ <0 0x40001000 0 0x1000>,
+ <0 0x40100000 0 0x100000>;
+ reg-names = "parf", "dbi", "elbi", "atu", "config";
+ device_type = "pci";
+ linux,pci-domain = <3>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <2>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
+ <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
+
+ interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc GCC_PCIE_3_PIPE_CLK>,
+ <&gcc GCC_PCIE_3_AUX_CLK>,
+ <&gcc GCC_PCIE_3_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_3_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_3_SLV_AXI_CLK>,
+ <&gcc GCC_PCIE_3_SLV_Q2A_AXI_CLK>,
+ <&gcc GCC_PCIE_3_CLKREF_CLK>,
+ <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
+ clock-names = "pipe",
+ "aux",
+ "cfg",
+ "bus_master",
+ "bus_slave",
+ "slave_q2a",
+ "ref",
+ "tbu";
+
+ assigned-clocks = <&gcc GCC_PCIE_3_AUX_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ iommus = <&apps_smmu 0x1e00 0x7f>;
+ iommu-map = <0x0 &apps_smmu 0x1e00 0x1>,
+ <0x100 &apps_smmu 0x1e01 0x1>;
+
+ resets = <&gcc GCC_PCIE_3_BCR>;
+ reset-names = "pci";
+
+ power-domains = <&gcc PCIE_3_GDSC>;
+
+ phys = <&pcie3_lane>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
+
+ pcie3_phy: phy@1c0c000 {
+ compatible = "qcom,sc8180x-qmp-pcie-phy";
+ reg = <0 0x1c0c000 0 0x1c0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+ <&gcc GCC_PCIE_3_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_3_CLKREF_CLK>,
+ <&gcc GCC_PCIE2_PHY_REFGEN_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+ resets = <&gcc GCC_PCIE_3_PHY_BCR>;
+ reset-names = "phy";
+
+ assigned-clocks = <&gcc GCC_PCIE3_PHY_REFGEN_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ status = "disabled";
+
+ pcie3_lane: lanes@1c0c200 {
+ reg = <0 0x1c0c200 0 0x170>, /* tx0 */
+ <0 0x1c0c400 0 0x200>, /* rx0 */
+ <0 0x1c0ca00 0 0x1f0>, /* pcs */
+ <0 0x1c0c600 0 0x170>, /* tx1 */
+ <0 0x1c0c800 0 0x200>, /* rx1 */
+ <0 0x1c0ce00 0 0xf4>; /* pcs_com */
+ clocks = <&gcc GCC_PCIE_3_PIPE_CLK>;
+ clock-names = "pipe0";
+
+ #phy-cells = <0>;
+ clock-output-names = "pcie_3_pipe_clk";
+ };
+ };
+
+ pcie1: pci@1c10000 {
+ compatible = "qcom,pcie-sc8180x", "snps,dw-pcie";
+ reg = <0 0x01c10000 0 0x3000>,
+ <0 0x68000000 0 0xf1d>,
+ <0 0x68000f20 0 0xa8>,
+ <0 0x68001000 0 0x1000>,
+ <0 0x68100000 0 0x100000>;
+ reg-names = "parf", "dbi", "elbi", "atu", "config";
+ device_type = "pci";
+ linux,pci-domain = <1>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <2>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x01000000 0x0 0x68200000 0x0 0x68200000 0x0 0x100000>,
+ <0x02000000 0x0 0x68300000 0x0 0x68300000 0x0 0x3d00000>;
+
+ interrupts = <GIC_SPI 755 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 747 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 746 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 745 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 744 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
+ <&gcc GCC_PCIE_1_AUX_CLK>,
+ <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
+ <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
+ <&gcc GCC_PCIE_1_CLKREF_CLK>,
+ <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
+ clock-names = "pipe",
+ "aux",
+ "cfg",
+ "bus_master",
+ "bus_slave",
+ "slave_q2a",
+ "ref",
+ "tbu";
+
+ assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ iommus = <&apps_smmu 0x1c80 0x7f>;
+ iommu-map = <0x0 &apps_smmu 0x1c80 0x1>,
+ <0x100 &apps_smmu 0x1c81 0x1>;
+
+ resets = <&gcc GCC_PCIE_1_BCR>;
+ reset-names = "pci";
+
+ power-domains = <&gcc PCIE_1_GDSC>;
+
+ interconnects = <&aggre2_noc MASTER_PCIE_1 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "pcie-mem";
+
+ phys = <&pcie1_lane>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
+
+ pcie1_phy: phy@1c16000 {
+ compatible = "qcom,sc8180x-qmp-pcie-phy";
+ reg = <0 0x1c16000 0 0x1c0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+ <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_1_CLKREF_CLK>,
+ <&gcc GCC_PCIE1_PHY_REFGEN_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+ resets = <&gcc GCC_PCIE_1_PHY_BCR>;
+ reset-names = "phy";
+
+ assigned-clocks = <&gcc GCC_PCIE1_PHY_REFGEN_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ status = "disabled";
+
+ pcie1_lane: lanes@1c0e200 {
+ reg = <0 0x1c16200 0 0x170>, /* tx0 */
+ <0 0x1c16400 0 0x200>, /* rx0 */
+ <0 0x1c16a00 0 0x1f0>, /* pcs */
+ <0 0x1c16600 0 0x170>, /* tx1 */
+ <0 0x1c16800 0 0x200>, /* rx1 */
+ <0 0x1c16e00 0 0xf4>; /* pcs_com */
+ clocks = <&gcc GCC_PCIE_1_PIPE_CLK>;
+ clock-names = "pipe0";
+
+ #phy-cells = <0>;
+ clock-output-names = "pcie_1_pipe_clk";
+ };
+ };
+
+ pcie2: pci@1c18000 {
+ compatible = "qcom,pcie-sc8180x", "snps,dw-pcie";
+ reg = <0 0x01c18000 0 0x3000>,
+ <0 0x70000000 0 0xf1d>,
+ <0 0x70000f20 0 0xa8>,
+ <0 0x70001000 0 0x1000>,
+ <0 0x70100000 0 0x100000>;
+ reg-names = "parf", "dbi", "elbi", "atu", "config";
+ device_type = "pci";
+ linux,pci-domain = <2>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <4>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x01000000 0x0 0x70200000 0x0 0x70200000 0x0 0x100000>,
+ <0x02000000 0x0 0x70300000 0x0 0x70300000 0x0 0x3d00000>;
+
+ interrupts = <GIC_SPI 671 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 663 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 662 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 661 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 660 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc GCC_PCIE_2_PIPE_CLK>,
+ <&gcc GCC_PCIE_2_AUX_CLK>,
+ <&gcc GCC_PCIE_2_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_2_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_2_SLV_AXI_CLK>,
+ <&gcc GCC_PCIE_2_SLV_Q2A_AXI_CLK>,
+ <&gcc GCC_PCIE_2_CLKREF_CLK>,
+ <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
+ clock-names = "pipe",
+ "aux",
+ "cfg",
+ "bus_master",
+ "bus_slave",
+ "slave_q2a",
+ "ref",
+ "tbu";
+
+ assigned-clocks = <&gcc GCC_PCIE_2_AUX_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ iommus = <&apps_smmu 0x1d00 0x7f>;
+ iommu-map = <0x0 &apps_smmu 0x1d00 0x1>,
+ <0x100 &apps_smmu 0x1d01 0x1>;
+
+ resets = <&gcc GCC_PCIE_2_BCR>;
+ reset-names = "pci";
+
+ power-domains = <&gcc PCIE_2_GDSC>;
+
+ phys = <&pcie2_lane>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
+
+ pcie2_phy: phy@1c1c000 {
+ compatible = "qcom,sc8180x-qmp-pcie-phy";
+ reg = <0 0x1c1c000 0 0x1c0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+ <&gcc GCC_PCIE_2_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_2_CLKREF_CLK>,
+ <&gcc GCC_PCIE2_PHY_REFGEN_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+ resets = <&gcc GCC_PCIE_2_PHY_BCR>;
+ reset-names = "phy";
+
+ assigned-clocks = <&gcc GCC_PCIE2_PHY_REFGEN_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ status = "disabled";
+
+ pcie2_lane: lanes@1c0e200 {
+ reg = <0 0x1c1c200 0 0x170>, /* tx0 */
+ <0 0x1c1c400 0 0x200>, /* rx0 */
+ <0 0x1c1ca00 0 0x1f0>, /* pcs */
+ <0 0x1c1c600 0 0x170>, /* tx1 */
+ <0 0x1c1c800 0 0x200>, /* rx1 */
+ <0 0x1c1ce00 0 0xf4>; /* pcs_com */
+ clocks = <&gcc GCC_PCIE_2_PIPE_CLK>;
+ clock-names = "pipe0";
+
+ #phy-cells = <0>;
+ clock-output-names = "pcie_2_pipe_clk";
+ };
+ };
+
+ ufs_mem_hc: ufshc@1d84000 {
+ compatible = "qcom,sc8180x-ufshc", "qcom,ufshc",
+ "jedec,ufs-2.0";
+ reg = <0 0x01d84000 0 0x2500>;
+ interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&ufs_mem_phy_lanes>;
+ phy-names = "ufsphy";
+ lanes-per-direction = <2>;
+ #reset-cells = <1>;
+ resets = <&gcc GCC_UFS_PHY_BCR>;
+ reset-names = "rst";
+
+ iommus = <&apps_smmu 0x300 0>;
+
+ clock-names =
+ "core_clk",
+ "bus_aggr_clk",
+ "iface_clk",
+ "core_clk_unipro",
+ "ref_clk",
+ "tx_lane0_sync_clk",
+ "rx_lane0_sync_clk",
+ "rx_lane1_sync_clk";
+ clocks =
+ <&gcc GCC_UFS_PHY_AXI_CLK>,
+ <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+ <&gcc GCC_UFS_PHY_AHB_CLK>,
+ <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+ <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+ <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
+ freq-table-hz =
+ <37500000 300000000>,
+ <0 0>,
+ <0 0>,
+ <37500000 300000000>,
+ <0 0>,
+ <0 0>,
+ <0 0>,
+ <0 0>;
+
+ status = "disabled";
+ };
+
+ ufs_mem_phy: phy@1d87000 {
+ compatible = "qcom,sc8180x-qmp-ufs-phy";
+ reg = <0 0x01d87000 0 0x1c0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ clock-names = "ref",
+ "ref_aux";
+ clocks = <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
+
+ resets = <&ufs_mem_hc 0>;
+ reset-names = "ufsphy";
+ status = "disabled";
+
+ ufs_mem_phy_lanes: lanes@1d87400 {
+ reg = <0 0x01d87400 0 0x108>,
+ <0 0x01d87600 0 0x1e0>,
+ <0 0x01d87c00 0 0x1dc>,
+ <0 0x01d87800 0 0x108>,
+ <0 0x01d87a00 0 0x1e0>;
+ #phy-cells = <0>;
+ };
+ };
+
+ ipa_virt: interconnect@1e00000 {
+ compatible = "qcom,sc8180x-ipa-virt";
+ reg = <0 0x01e00000 0 0x1000>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ tcsr_mutex: hwlock@1f40000 {
+ compatible = "qcom,tcsr-mutex";
+ reg = <0x0 0x01f40000 0x0 0x40000>;
+ #hwlock-cells = <1>;
+ };
+
+ gpu: gpu@2c00000 {
+ compatible = "qcom,adreno-680.1", "qcom,adreno";
+ #stream-id-cells = <16>;
+
+ reg = <0 0x02c00000 0 0x40000>;
+ reg-names = "kgsl_3d0_reg_memory";
+
+ interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
+
+ iommus = <&adreno_smmu 0 0xc01>;
+
+ operating-points-v2 = <&gpu_opp_table>;
+
+ interconnects = <&gem_noc MASTER_GRAPHICS_3D 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "gfx-mem";
+
+ qcom,gmu = <&gmu>;
+ status = "disabled";
+
+ gpu_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-514000000 {
+ opp-hz = /bits/ 64 <514000000>;
+ opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+ };
+
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+ };
+
+ opp-461000000 {
+ opp-hz = /bits/ 64 <461000000>;
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+ };
+
+ opp-405000000 {
+ opp-hz = /bits/ 64 <405000000>;
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+ };
+
+ opp-315000000 {
+ opp-hz = /bits/ 64 <315000000>;
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+ };
+
+ opp-256000000 {
+ opp-hz = /bits/ 64 <256000000>;
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+ };
+
+ opp-177000000 {
+ opp-hz = /bits/ 64 <177000000>;
+ opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+ };
+ };
+ };
+
+ gmu: gmu@2c6a000 {
+ compatible="qcom,adreno-gmu-680.1", "qcom,adreno-gmu";
+
+ reg = <0 0x02c6a000 0 0x30000>,
+ <0 0x0b290000 0 0x10000>,
+ <0 0x0b490000 0 0x10000>;
+ reg-names = "gmu", "gmu_pdc", "gmu_pdc_seq";
+
+ interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hfi", "gmu";
+
+ clocks = <&gpucc GPU_CC_AHB_CLK>,
+ <&gpucc GPU_CC_CX_GMU_CLK>,
+ <&gpucc GPU_CC_CXO_CLK>,
+ <&gcc GCC_DDRSS_GPU_AXI_CLK>,
+ <&gcc GCC_GPU_MEMNOC_GFX_CLK>;
+ clock-names = "ahb", "gmu", "cxo", "axi", "memnoc";
+
+ power-domains = <&gpucc GPU_CX_GDSC>,
+ <&gpucc GPU_GX_GDSC>;
+ power-domain-names = "cx", "gx";
+
+ iommus = <&adreno_smmu 5 0xc00>;
+
+ operating-points-v2 = <&gmu_opp_table>;
+
+ gmu_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-200000000 {
+ opp-hz = /bits/ 64 <200000000>;
+ opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+ };
+
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+ };
+ };
+ };
+
+ gpucc: clock-controller@2c90000 {
+ compatible = "qcom,sc8180x-gpucc";
+ reg = <0 0x02c90000 0 0x9000>;
+ clocks = <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_GPU_GPLL0_CLK_SRC>,
+ <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>;
+ clock-names = "bi_tcxo",
+ "gcc_gpu_gpll0_clk_src",
+ "gcc_gpu_gpll0_div_clk_src";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ };
+
+ adreno_smmu: iommu@2ca0000 {
+ compatible = "qcom,sc8180x-smmu-500", "qcom,adreno-smmu", "arm,mmu-500";
+ reg = <0 0x02ca0000 0 0x10000>;
+ #iommu-cells = <2>;
+ #global-interrupts = <1>;
+ interrupts = <GIC_SPI 674 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 681 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 682 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 683 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 684 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 685 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 686 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 687 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 688 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gpucc GPU_CC_AHB_CLK>,
+ <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
+ <&gcc GCC_GPU_SNOC_DVM_GFX_CLK>;
+ clock-names = "ahb", "bus", "iface";
+
+ power-domains = <&gpucc GPU_CX_GDSC>;
+ };
+
+ tlmm: pinctrl@3100000 {
+ compatible = "qcom,sc8180x-tlmm";
+ reg = <0 0x03100000 0 0x300000>,
+ <0 0x03500000 0 0x700000>,
+ <0 0x03d00000 0 0x300000>;
+ reg-names = "west", "east", "south";
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&tlmm 0 0 191>;
+ wakeup-parent = <&pdc>;
+ };
+
+ remoteproc_mpss: remoteproc@4080000 {
+ compatible = "qcom,sc8180x-mpss-pas";
+ reg = <0x0 0x04080000 0x0 0x4040>;
+
+ interrupts-extended = <&intc GIC_SPI 266 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready", "handover",
+ "stop-ack", "shutdown-ack";
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "xo";
+
+ power-domains = <&rpmhpd SC8180X_CX>,
+ <&rpmhpd SC8180X_MSS>;
+ power-domain-names = "cx", "mss";
+
+ qcom,qmp = <&aoss_qmp>;
+
+ qcom,smem-states = <&modem_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ glink-edge {
+ interrupts = <GIC_SPI 449 IRQ_TYPE_EDGE_RISING>;
+ label = "modem";
+ qcom,remote-pid = <1>;
+ mboxes = <&apss_shared 12>;
+ };
+ };
+
+ remoteproc_cdsp: remoteproc@8300000 {
+ compatible = "qcom,sc8180x-cdsp-pas";
+ reg = <0x0 0x08300000 0x0 0x4040>;
+
+ interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,
+ <&cdsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&cdsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&cdsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&cdsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "xo";
+
+ power-domains = <&rpmhpd SC8180X_CX>;
+ power-domain-names = "cx";
+
+ qcom,qmp = <&aoss_qmp>;
+
+ qcom,smem-states = <&cdsp_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts = <GIC_SPI 574 IRQ_TYPE_EDGE_RISING>;
+ label = "cdsp";
+ qcom,remote-pid = <5>;
+ mboxes = <&apss_shared 4>;
+ };
+ };
+
+ usb_prim_hsphy: phy@88e2000 {
+ compatible = "qcom,sc8180x-usb-hs-phy",
+ "qcom,usb-snps-hs-7nm-phy";
+ reg = <0 0x088e2000 0 0x400>;
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "ref";
+ resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ usb_sec_hsphy: phy@88e3000 {
+ compatible = "qcom,sc8180x-usb-hs-phy",
+ "qcom,usb-snps-hs-7nm-phy";
+ reg = <0 0x088e3000 0 0x400>;
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "ref";
+ resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
+
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ usb_prim_qmpphy: phy@88e9000 {
+ compatible = "qcom,sc8180x-qmp-usb3-dp-phy";
+ reg = <0 0x088e9000 0 0x18c>,
+ <0 0x088e8000 0 0x38>,
+ <0 0x088ea000 0 0x40>;
+ reg-names = "reg-base", "dp_com";
+ clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
+ <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
+ clock-names = "aux", "ref_clk_src", "ref", "com_aux";
+ resets = <&gcc GCC_USB3_DP_PHY_PRIM_SP0_BCR>,
+ <&gcc GCC_USB3_PHY_PRIM_SP0_BCR>;
+ reset-names = "phy", "common";
+
+ #clock-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ status = "disabled";
+
+ usb_prim_ssphy: usb3-phy@88e9200 {
+ reg = <0 0x088e9200 0 0x200>,
+ <0 0x088e9400 0 0x200>,
+ <0 0x088e9c00 0 0x218>,
+ <0 0x088e9600 0 0x200>,
+ <0 0x088e9800 0 0x200>,
+ <0 0x088e9a00 0 0x100>;
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "usb3_prim_phy_pipe_clk_src";
+ };
+
+ usb_prim_dpphy: dp-phy@88ea200 {
+ reg = <0 0x088ea200 0 0x200>,
+ <0 0x088ea400 0 0x200>,
+ <0 0x088eaa00 0 0x200>,
+ <0 0x088ea600 0 0x200>,
+ <0 0x088ea800 0 0x200>;
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+ };
+ };
+
+ usb_sec_qmpphy: phy@88ee000 {
+ compatible = "qcom,sc8180x-qmp-usb3-dp-phy";
+ reg = <0 0x088ee000 0 0x18c>,
+ <0 0x088ed000 0 0x10>,
+ <0 0x088ef000 0 0x40>;
+ reg-names = "reg-base", "dp_com";
+ clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_USB3_SEC_CLKREF_CLK>,
+ <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
+ clock-names = "aux", "ref_clk_src", "ref", "com_aux";
+ resets = <&gcc GCC_USB3_DP_PHY_SEC_BCR>,
+ <&gcc GCC_USB3_PHY_SEC_BCR>;
+ reset-names = "phy", "common";
+
+ #clock-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ status = "disabled";
+
+ usb_sec_ssphy: usb3-phy@88e9200 {
+ reg = <0 0x088ee200 0 0x200>,
+ <0 0x088ee400 0 0x200>,
+ <0 0x088eec00 0 0x218>,
+ <0 0x088ee600 0 0x200>,
+ <0 0x088ee800 0 0x200>,
+ <0 0x088eea00 0 0x100>;
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "usb3_sec_phy_pipe_clk_src";
+ };
+
+ usb_sec_dpphy: dp-phy@88ef200 {
+ reg = <0 0x088ef200 0 0x200>,
+ <0 0x088ef400 0 0x200>,
+ <0 0x088efa00 0 0x200>,
+ <0 0x088ef600 0 0x200>,
+ <0 0x088ef800 0 0x200>;
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+ clock-output-names = "qmp_dptx1_phy_pll_link_clk", "qmp_dptx1_phy_pll_vco_div_clk";
+ };
+ };
+
+ system-cache-controller@9200000 {
+ compatible = "qcom,sc8180x-llcc";
+ reg = <0 0x09200000 0 0x50000>, <0 0x09600000 0 0x50000>;
+ reg-names = "llcc_base", "llcc_broadcast_base";
+ interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gem_noc: interconnect@9680000 {
+ compatible = "qcom,sc8180x-gem-noc";
+ reg = <0 0x09680000 0 0x58200>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ usb_prim: usb@a6f8800 {
+ compatible = "qcom,sc8180x-dwc3", "qcom,dwc3";
+ reg = <0 0x0a6f8800 0 0x400>;
+ interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hs_phy_irq", "ss_phy_irq",
+ "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+ clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+ <&gcc GCC_USB3_SEC_CLKREF_CLK>;
+ clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+ "sleep", "xo";
+ resets = <&gcc GCC_USB30_PRIM_BCR>;
+ power-domains = <&gcc USB30_PRIM_GDSC>;
+
+ interconnects = <&aggre1_noc MASTER_USB3 0 &mc_virt SLAVE_EBI_CH0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_USB3 0>;
+ interconnect-names = "usb-ddr", "apps-usb";
+
+ assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+ assigned-clock-rates = <19200000>, <200000000>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ dma-ranges;
+
+ status = "disabled";
+
+ usb_prim_dwc3: usb@a600000 {
+ compatible = "snps,dwc3";
+ reg = <0 0x0a600000 0 0xcd00>;
+ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&apps_smmu 0x140 0>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_enblslpm_quirk;
+ phys = <&usb_prim_hsphy>, <&usb_prim_ssphy>;
+ phy-names = "usb2-phy", "usb3-phy";
+ };
+ };
+
+ usb_sec: usb@a8f8800 {
+ compatible = "qcom,sc8180x-dwc3", "qcom,dwc3";
+ reg = <0 0x0a8f8800 0 0x400>;
+
+ clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
+ <&gcc GCC_USB30_SEC_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
+ <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_SEC_SLEEP_CLK>,
+ <&gcc GCC_USB3_SEC_CLKREF_CLK>;
+ clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+ "sleep", "xo";
+ resets = <&gcc GCC_USB30_SEC_BCR>;
+ power-domains = <&gcc USB30_SEC_GDSC>;
+ interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 487 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 490 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 491 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hs_phy_irq", "ss_phy_irq",
+ "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+ assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_SEC_MASTER_CLK>;
+ assigned-clock-rates = <19200000>, <200000000>;
+
+ interconnects = <&aggre1_noc MASTER_USB3_1 0 &mc_virt SLAVE_EBI_CH0 0>,
+ <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_USB3_1 0>;
+ interconnect-names = "usb-ddr", "apps-usb";
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ dma-ranges;
+
+ status = "disabled";
+
+ usb_sec_dwc3: usb@a800000 {
+ compatible = "snps,dwc3";
+ reg = <0 0x0a800000 0 0xcd00>;
+ interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&apps_smmu 0x160 0>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_enblslpm_quirk;
+ phys = <&usb_sec_hsphy>, <&usb_sec_ssphy>;
+ phy-names = "usb2-phy", "usb3-phy";
+ };
+ };
+
+ mdss: mdss@ae00000 {
+ compatible = "qcom,sc8180x-mdss";
+ reg = <0 0x0ae00000 0 0x1000>;
+ reg-names = "mdss";
+
+ power-domains = <&dispcc MDSS_GDSC>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&gcc GCC_DISP_SF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>;
+ clock-names = "iface", "bus", "nrt_bus", "core";
+
+ resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interconnects = <&mmss_noc MASTER_MDP_PORT0 0 &mc_virt SLAVE_EBI_CH0 0>,
+ <&mmss_noc MASTER_MDP_PORT1 0 &mc_virt SLAVE_EBI_CH0 0>;
+ interconnect-names = "mdp0-mem", "mdp1-mem";
+
+ iommus = <&apps_smmu 0x800 0x420>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ status = "disabled";
+
+ mdss_mdp: mdp@ae01000 {
+ compatible = "qcom,sc8180x-dpu";
+ reg = <0 0x0ae01000 0 0x8f000>,
+ <0 0x0aeb0000 0 0x2008>;
+ reg-names = "mdp", "vbif";
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "iface", "bus", "core", "vsync";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ assigned-clock-rates = <460000000>,
+ <19200000>;
+
+ operating-points-v2 = <&mdp_opp_table>;
+ power-domains = <&rpmhpd SC8180X_MMCX>;
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dpu_intf0_out: endpoint {
+ remote-endpoint = <&dp0_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ dpu_intf2_out: endpoint {
+ remote-endpoint = <&dsi1_in>;
+ };
+ };
+
+ port@4 {
+ reg = <4>;
+ dpu_intf4_out: endpoint {
+ remote-endpoint = <&dp1_in>;
+ };
+ };
+
+ port@5 {
+ reg = <5>;
+ dpu_intf5_out: endpoint {
+ remote-endpoint = <&edp_in>;
+ };
+ };
+ };
+
+ mdp_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-200000000 {
+ opp-hz = /bits/ 64 <200000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-345000000 {
+ opp-hz = /bits/ 64 <345000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-460000000 {
+ opp-hz = /bits/ 64 <460000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
+ dsi0: dsi@ae94000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae94000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ operating-points-v2 = <&dsi_opp_table>;
+ power-domains = <&rpmhpd SC8180X_MMCX>;
+
+ phys = <&dsi0_phy>;
+ phy-names = "dsi";
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi0_in: endpoint {
+ remote-endpoint = <&dpu_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi0_out: endpoint {
+ };
+ };
+ };
+
+ dsi_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-187500000 {
+ opp-hz = /bits/ 64 <187500000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-358000000 {
+ opp-hz = /bits/ 64 <358000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+ };
+ };
+
+ dsi0_phy: dsi-phy@ae94400 {
+ compatible = "qcom,dsi-phy-7nm";
+ reg = <0 0x0ae94400 0 0x200>,
+ <0 0x0ae94600 0 0x280>,
+ <0 0x0ae94900 0 0x260>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+
+ status = "disabled";
+ };
+
+ dsi1: dsi@ae96000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae96000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC1_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ operating-points-v2 = <&dsi_opp_table>;
+ power-domains = <&rpmhpd SC8180X_MMCX>;
+
+ phys = <&dsi1_phy>;
+ phy-names = "dsi";
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi1_in: endpoint {
+ remote-endpoint = <&dpu_intf2_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi1_out: endpoint {
+ };
+ };
+ };
+ };
+
+ dsi1_phy: dsi-phy@ae96400 {
+ compatible = "qcom,dsi-phy-7nm";
+ reg = <0 0x0ae96400 0 0x200>,
+ <0 0x0ae96600 0 0x280>,
+ <0 0x0ae96900 0 0x260>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+
+ status = "disabled";
+ };
+
+ mdss_dp0: displayport-controller@ae90000 {
+ compatible = "qcom,sc8180x-dp";
+ reg = <0 0xae90000 0 0x200>,
+ <0 0xae90200 0 0x200>,
+ <0 0xae90400 0 0x600>,
+ <0 0xae90a00 0 0x400>;
+ interrupt-parent = <&mdss>;
+ interrupts = <12>;
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
+ clock-names = "core_iface", "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface", "stream_pixel";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>,
+ <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
+ assigned-clock-parents = <&usb_prim_dpphy 0>, <&usb_prim_dpphy 1>;
+
+ phys = <&usb_prim_dpphy>;
+ phy-names = "dp";
+
+ #sound-dai-cells = <0>;
+
+ operating-points-v2 = <&dp0_opp_table>;
+ power-domains = <&rpmhpd SC8180X_CX>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dp0_in: endpoint {
+ remote-endpoint = <&dpu_intf0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ };
+ };
+
+ dp0_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
+ mdss_dp1: displayport-controller@ae98000 {
+ compatible = "qcom,sc8180x-dp";
+ reg = <0 0xae98000 0 0x200>,
+ <0 0xae98200 0 0x200>,
+ <0 0xae98400 0 0x600>,
+ <0 0xae98a00 0 0x400>;
+ interrupt-parent = <&mdss>;
+ interrupts = <13>;
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_AUX1_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_LINK1_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_LINK1_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_PIXEL2_CLK>;
+ clock-names = "core_iface", "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface", "stream_pixel";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK1_CLK_SRC>,
+ <&dispcc DISP_CC_MDSS_DP_PIXEL2_CLK_SRC>;
+ assigned-clock-parents = <&usb_sec_dpphy 0>, <&usb_sec_dpphy 1>;
+
+ phys = <&usb_sec_dpphy>;
+ phy-names = "dp";
+
+ #sound-dai-cells = <0>;
+
+ operating-points-v2 = <&dp0_opp_table>;
+ power-domains = <&rpmhpd SC8180X_CX>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dp1_in: endpoint {
+ remote-endpoint = <&dpu_intf4_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ };
+ };
+
+ dp1_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
+ mdss_edp: displayport-controller@ae9a000 {
+ compatible = "qcom,sc8180x-edp";
+ reg = <0 0xae9a000 0 0x200>,
+ <0 0xae9a200 0 0x200>,
+ <0 0xae9a400 0 0x600>,
+ <0 0xae9aa00 0 0x400>;
+ interrupt-parent = <&mdss>;
+ interrupts = <14>;
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_EDP_AUX_CLK>,
+ <&dispcc DISP_CC_MDSS_EDP_LINK_CLK>,
+ <&dispcc DISP_CC_MDSS_EDP_LINK_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK>;
+ clock-names = "core_iface", "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface", "stream_pixel";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_EDP_LINK_CLK_SRC>,
+ <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK_SRC>;
+ assigned-clock-parents = <&edp_phy 0>, <&edp_phy 1>;
+
+ phys = <&edp_phy>;
+ phy-names = "dp";
+
+ #sound-dai-cells = <0>;
+
+ operating-points-v2 = <&edp_opp_table>;
+ power-domains = <&rpmhpd SC8180X_CX>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ edp_in: endpoint {
+ remote-endpoint = <&dpu_intf5_out>;
+ };
+ };
+ };
+
+ edp_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+ };
+
+ edp_phy: phy@aec2a00 {
+ compatible = "qcom,sc8180x-edp-phy";
+ reg = <0 0x0aec2a00 0 0x1c0>,
+ <0 0x0aec2200 0 0xa0>,
+ <0 0x0aec2600 0 0xa0>,
+ <0 0x0aec2000 0 0x19c>;
+
+ clocks = <&dispcc DISP_CC_MDSS_EDP_AUX_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>;
+ clock-names = "aux", "cfg_ahb";
+
+ power-domains = <&dispcc MDSS_GDSC>;
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+ };
+
+ dispcc: clock-controller@af00000 {
+ compatible = "qcom,sc8180x-dispcc";
+ reg = <0 0x0af00000 0 0x20000>;
+ clocks = <&rpmhcc RPMH_CXO_CLK>,
+ <&sleep_clk>,
+ <&usb_prim_dpphy 0>,
+ <&usb_prim_dpphy 1>,
+ <&usb_sec_dpphy 0>,
+ <&usb_sec_dpphy 1>,
+ <&edp_phy 0>,
+ <&edp_phy 1>;
+ clock-names = "bi_tcxo",
+ "sleep_clk",
+ "dp_phy_pll_link_clk",
+ "dp_phy_pll_vco_div_clk",
+ "dptx1_phy_pll_link_clk",
+ "dptx1_phy_pll_vco_div_clk",
+ "edp_phy_pll_link_clk",
+ "edp_phy_pll_vco_div_clk";
+ power-domains = <&rpmhpd SC8180X_MMCX>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+
+ status = "disabled";
+ };
+
+ pdc: interrupt-controller@b220000 {
+ compatible = "qcom,sc8180x-pdc", "qcom,pdc";
+ reg = <0 0x0b220000 0 0x30000>;
+ qcom,pdc-ranges = <0 480 94>, <94 609 31>;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&intc>;
+ interrupt-controller;
+ };
+
+ tsens0: thermal-sensor@c263000 {
+ compatible = "qcom,sc8180x-tsens", "qcom,tsens-v2";
+ reg = <0 0x0c263000 0 0x1ff>, /* TM */
+ <0 0x0c222000 0 0x1ff>; /* SROT */
+ #qcom,sensors = <16>;
+ interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow", "critical";
+ #thermal-sensor-cells = <1>;
+ };
+
+ tsens1: thermal-sensor@c265000 {
+ compatible = "qcom,sc8180x-tsens", "qcom,tsens-v2";
+ reg = <0 0x0c265000 0 0x1ff>, /* TM */
+ <0 0x0c223000 0 0x1ff>; /* SROT */
+ #qcom,sensors = <9>;
+ interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow", "critical";
+ #thermal-sensor-cells = <1>;
+ };
+
+ aoss_qmp: power-controller@c300000 {
+ compatible = "qcom,sc8180x-aoss-qmp", "qcom,aoss-qmp";
+ reg = <0x0 0x0c300000 0x0 0x100000>;
+ interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&apss_shared 0>;
+
+ #clock-cells = <0>;
+ #power-domain-cells = <1>;
+ };
+
+ spmi_bus: spmi@c440000 {
+ compatible = "qcom,spmi-pmic-arb";
+ reg = <0x0 0x0c440000 0x0 0x0001100>,
+ <0x0 0x0c600000 0x0 0x2000000>,
+ <0x0 0x0e600000 0x0 0x0100000>,
+ <0x0 0x0e700000 0x0 0x00a0000>,
+ <0x0 0x0c40a000 0x0 0x0026000>;
+ reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+ interrupt-names = "periph_irq";
+ interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>;
+ qcom,ee = <0>;
+ qcom,channel = <0>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <4>;
+ cell-index = <0>;
+ };
+
+ apps_smmu: iommu@15000000 {
+ compatible = "qcom,sc8180x-smmu-500", "arm,mmu-500";
+ reg = <0 0x15000000 0 0x100000>;
+ #iommu-cells = <2>;
+ #global-interrupts = <1>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 410 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 411 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 706 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 708 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 709 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 710 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 711 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 712 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 713 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 714 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 715 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 643 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 642 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 640 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 768 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 769 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 770 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 771 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 772 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 773 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 774 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 775 IRQ_TYPE_LEVEL_HIGH>;
+
+ };
+
+ remoteproc_adsp: remoteproc@17300000 {
+ compatible = "qcom,sc8180x-adsp-pas";
+ reg = <0x0 0x17300000 0x0 0x4040>;
+
+ interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "xo";
+
+ power-domains = <&rpmhpd SC8180X_CX>;
+ power-domain-names = "cx";
+
+ qcom,qmp = <&aoss_qmp>;
+
+ qcom,smem-states = <&adsp_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ remoteproc_adsp_glink: glink-edge {
+ interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
+ label = "lpass";
+ qcom,remote-pid = <2>;
+ mboxes = <&apss_shared 8>;
+ };
+ };
+
+ intc: interrupt-controller@17a00000 {
+ compatible = "arm,gic-v3";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ reg = <0x0 0x17a00000 0x0 0x10000>, /* GICD */
+ <0x0 0x17a60000 0x0 0x100000>; /* GICR * 8 */
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ apss_shared: mailbox@17c00000 {
+ compatible = "qcom,sc8180x-apss-shared";
+ reg = <0x0 0x17c00000 0x0 0x1000>;
+ #mbox-cells = <1>;
+ };
+
+ timer@17c20000 {
+ compatible = "arm,armv7-timer-mem";
+ reg = <0x0 0x17c20000 0x0 0x1000>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0 0x20000000>;
+
+ frame@17c21000{
+ reg = <0x17c21000 0x1000>,
+ <0x17c22000 0x1000>;
+ frame-number = <0>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ frame@17c23000 {
+ reg = <0x17c23000 0x1000>;
+ frame-number = <1>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@17c25000 {
+ reg = <0x17c25000 0x1000>;
+ frame-number = <2>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@17c27000 {
+ reg = <0x17c26000 0x1000>;
+ frame-number = <3>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@17c29000 {
+ reg = <0x17c29000 0x1000>;
+ frame-number = <4>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@17c2b000 {
+ reg = <0x17c2b000 0x1000>;
+ frame-number = <5>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@17c2d000 {
+ reg = <0x17c2d000 0x1000>;
+ frame-number = <6>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+ };
+
+ apps_rsc: rsc@18200000 {
+ compatible = "qcom,rpmh-rsc";
+ reg = <0x0 0x18200000 0x0 0x10000>,
+ <0x0 0x18210000 0x0 0x10000>,
+ <0x0 0x18220000 0x0 0x10000>;
+ reg-names = "drv-0", "drv-1", "drv-2";
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ qcom,tcs-offset = <0xd00>;
+ qcom,drv-id = <2>;
+ qcom,tcs-config = <ACTIVE_TCS 2>,
+ <SLEEP_TCS 1>,
+ <WAKE_TCS 1>,
+ <CONTROL_TCS 0>;
+ label = "apps_rsc";
+
+ apps_bcm_voter: bcm-voter {
+ compatible = "qcom,bcm-voter";
+ };
+
+ rpmhcc: clock-controller {
+ compatible = "qcom,sc8180x-rpmh-clk";
+ #clock-cells = <1>;
+ clock-names = "xo";
+ clocks = <&xo_board_clk>;
+ };
+
+ rpmhpd: power-controller {
+ compatible = "qcom,sc8180x-rpmhpd";
+ #power-domain-cells = <1>;
+ operating-points-v2 = <&rpmhpd_opp_table>;
+
+ rpmhpd_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ rpmhpd_opp_ret: opp1 {
+ opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+ };
+
+ rpmhpd_opp_min_svs: opp2 {
+ opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+ };
+
+ rpmhpd_opp_low_svs: opp3 {
+ opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+ };
+
+ rpmhpd_opp_svs: opp4 {
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+ };
+
+ rpmhpd_opp_svs_l1: opp5 {
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+ };
+
+ rpmhpd_opp_nom: opp6 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+ };
+
+ rpmhpd_opp_nom_l1: opp7 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+ };
+
+ rpmhpd_opp_nom_l2: opp8 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+ };
+
+ rpmhpd_opp_turbo: opp9 {
+ opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+ };
+
+ rpmhpd_opp_turbo_l1: opp10 {
+ opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+ };
+ };
+ };
+ };
+
+ osm_l3: interconnect@18321000 {
+ compatible = "qcom,sc8180x-osm-l3";
+ reg = <0 0x18321000 0 0x1400>;
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
+ clock-names = "xo", "alternate";
+
+ #interconnect-cells = <1>;
+ };
+
+ lmh@18350800 {
+ compatible = "qcom,sc8180x-lmh";
+ reg = <0 0x18350800 0 0x400>;
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ cpus = <&CPU4>;
+ qcom,lmh-temp-arm-millicelsius = <65000>;
+ qcom,lmh-temp-low-millicelsius = <94500>;
+ qcom,lmh-temp-high-millicelsius = <95000>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ lmh@18358800 {
+ compatible = "qcom,sc8180x-lmh";
+ reg = <0 0x18358800 0 0x400>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ cpus = <&CPU0>;
+ qcom,lmh-temp-arm-millicelsius = <65000>;
+ qcom,lmh-temp-low-millicelsius = <94500>;
+ qcom,lmh-temp-high-millicelsius = <95000>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ cpufreq_hw: cpufreq@18323000 {
+ compatible = "qcom,cpufreq-hw";
+ reg = <0 0x18323000 0 0x1400>, <0 0x18325800 0 0x1400>;
+ reg-names = "freq-domain0", "freq-domain1";
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
+ clock-names = "xo", "alternate";
+
+ #freq-domain-cells = <1>;
+ };
+
+ wifi: wifi@18800000 {
+ compatible = "qcom,wcn3990-wifi";
+ reg = <0 0x18800000 0 0x800000>;
+ reg-names = "membase";
+ clock-names = "cxo_ref_clk_pin";
+ clocks = <&rpmhcc RPMH_RF_CLK2>;
+ interrupts = <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&apps_smmu 0x0640 0x1>;
+ qcom,msa-fixed-perm;
+ status = "disabled";
+ };
+ };
+
+ thermal-zones {
+ cpu0-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 1>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu1-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 2>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu2-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 3>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu3-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 4>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu4-top-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 7>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu5-top-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 8>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu6-top-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 9>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu7-top-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 10>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu4-bottom-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 11>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu5-bottom-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 12>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu6-bottom-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 13>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu7-bottom-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 14>;
+
+ trips {
+ cpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ aoss0-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 0>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ cluster0-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 5>;
+
+ trips {
+ cluster-crit {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cluster1-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 6>;
+
+ trips {
+ cluster-crit {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ gpu-thermal-top {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 15>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ aoss1-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 0>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ wlan-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 1>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ video-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 2>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ mem-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 3>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ q6-hvx-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 4>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ camera-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 5>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ compute-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 6>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ mdm-dsp-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 7>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ npu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 8>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ gpu-thermal-bottom {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens1 11>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
--
2.37.3
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 5/6] arm64: dts: qcom: sc8180x: Introduce Primus
2022-09-16 12:11 [PATCH 0/6] Introduce the SC8180x devices Vinod Koul
` (3 preceding siblings ...)
2022-09-16 12:12 ` [PATCH 4/6] arm64: dts: qcom: Introduce the SC8180x platform Vinod Koul
@ 2022-09-16 12:12 ` Vinod Koul
2022-09-17 16:36 ` Krzysztof Kozlowski
2022-09-16 12:12 ` [PATCH 6/6] arm64: dts: qcom: sc8180x: Introduce Lenovo Flex 5G Vinod Koul
5 siblings, 1 reply; 14+ messages in thread
From: Vinod Koul @ 2022-09-16 12:12 UTC (permalink / raw)
To: Bjorn Andersson
Cc: linux-arm-msm, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
devicetree, linux-kernel, Vinod Koul
From: Bjorn Andersson <bjorn.andersson@linaro.org>
Introduce support for the SC8180X reference device, aka Primus, with
debug UART, regulators, UFS and USB support.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi | 326 +++++++++
arch/arm64/boot/dts/qcom/sc8180x-primus.dts | 706 ++++++++++++++++++++
3 files changed, 1033 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/sc8180x-primus.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index d7669a7cee9f..f1c620bb078e 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -112,6 +112,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-villager-r1-lte.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp2.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-crd-r3.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sc8180x-primus.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-crd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-lenovo-thinkpad-x13s.dtb
dtb-$(CONFIG_ARCH_QCOM) += sda660-inforce-ifc6560.dtb
diff --git a/arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi b/arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi
new file mode 100644
index 000000000000..49c146b6f37f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi
@@ -0,0 +1,326 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2021-2022, Linaro Limited
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+
+/ {
+ thermal-zones {
+ pmc8180-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pmc8180_temp>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+
+ trip2 {
+ temperature = <145000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ pmc8180c-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pmc8180c_temp>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+
+ trip2 {
+ temperature = <145000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+ };
+};
+
+&spmi_bus {
+ pmc8180_0: pmic@0 {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pon: power-on@800 {
+ compatible = "qcom,pm8916-pon";
+ reg = <0x0800>;
+ pwrkey {
+ compatible = "qcom,pm8941-pwrkey";
+ interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_POWER>;
+
+ status = "disabled";
+ };
+ };
+
+ pmc8180_temp: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+ io-channels = <&pmc8180_adc ADC5_DIE_TEMP>;
+ io-channel-names = "thermal";
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmc8180_adc: adc@3100 {
+ compatible = "qcom,spmi-adc5";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+ ref-gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_gnd";
+ };
+
+ vref-1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ label = "vref_1p25";
+ };
+
+ die-temp@6 {
+ reg = <ADC5_DIE_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ label = "die_temp";
+ };
+ };
+
+ pmc8180_adc_tm: adc-tm@3500 {
+ compatible = "qcom,spmi-adc-tm5";
+ reg = <0x3500>;
+ interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+ #thermal-sensor-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ rtc@6000 {
+ compatible = "qcom,pm8941-rtc";
+ reg = <0x6000>;
+ reg-names = "rtc", "alarm";
+ interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
+ };
+
+ pmc8180_gpios: gpio@c000 {
+ compatible = "qcom,pmc8180-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmic@1 {
+ compatible = "qcom,pmc8180", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ pmic@2 {
+ compatible = "qcom,smb2351", "qcom,spmi-pmic";
+ reg = <0x2 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc@3100 {
+ compatible = "qcom,spmi-adc-rev2";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+ ref-gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_gnd";
+ };
+
+ vref-1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ label = "vref_1p25";
+ };
+
+ vcoin@85 {
+ reg = <0x85>;
+ qcom,pre-scaling = <1 1>;
+ label = "vcoin2";
+ };
+ };
+ };
+
+ pmic@6 {
+ compatible = "qcom,pm8150c", "qcom,spmi-pmic";
+ reg = <0x6 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ pmic@8 {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0x8 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ pmic@a {
+ compatible = "qcom,smb2351", "qcom,spmi-pmic";
+ reg = <0xa SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc@3100 {
+ compatible = "qcom,spmi-adc-rev2";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ interrupts = <0xa 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+ ref-gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_gnd";
+ };
+
+ vref-1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ label = "vref_1p25";
+ };
+
+ vcoin@85 {
+ reg = <0x85>;
+ qcom,pre-scaling = <1 1>;
+ label = "vcoin";
+ };
+ };
+ };
+
+ pmic@4 {
+ compatible = "qcom,pm8150c", "qcom,spmi-pmic";
+ reg = <0x4 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ power-on@800 {
+ compatible = "qcom,pm8916-pon";
+ reg = <0x0800>;
+
+ status = "disabled";
+ };
+
+ pmc8180c_temp: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+ io-channels = <&pmc8180c_adc ADC5_DIE_TEMP>;
+ io-channel-names = "thermal";
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmc8180c_adc: adc@3100 {
+ compatible = "qcom,spmi-adc5";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+ ref-gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_gnd";
+ };
+
+ vref-1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ label = "vref_1p25";
+ };
+
+ die-temp@6 {
+ reg = <ADC5_DIE_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ label = "die_temp";
+ };
+ };
+
+ pmc8180c_adc_tm: adc-tm@3500 {
+ compatible = "qcom,spmi-adc-tm5";
+ reg = <0x3500>;
+ interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+ #thermal-sensor-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ pmc8180c_gpios: gpio@c000 {
+ compatible = "qcom,pmc8180c-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmic@5 {
+ compatible = "qcom,pmc8180c", "qcom,spmi-pmic";
+ reg = <0x5 SPMI_USID>;
+
+ pmc8180c_lpg: lpg {
+ compatible = "qcom,pmc8180c-lpg";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #pwm-cells = <2>;
+
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/sc8180x-primus.dts b/arch/arm64/boot/dts/qcom/sc8180x-primus.dts
new file mode 100644
index 000000000000..14582dbe7155
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc8180x-primus.dts
@@ -0,0 +1,706 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020-2021, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sc8180x.dtsi"
+#include "sc8180x-pmics.dtsi"
+
+/ {
+ model = "Qualcomm SC8180x Primus";
+ compatible = "qcom,sc8180x-primus", "qcom,sc8180x";
+
+ aliases {
+ serial0 = &uart12;
+ serial1 = &uart13;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pmc8180c_lpg 4 1000000>;
+ enable-gpios = <&pmc8180c_gpios 8 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_pwm_default_state>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&hall_int_active_state>;
+
+ lid-switch {
+ gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ wakeup-source;
+ wakeup-event-action = <EV_ACT_DEASSERTED>;
+ };
+ };
+
+ reserved-memory {
+ rmtfs_mem: rmtfs-region@85500000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0x0 0x85500000 0x0 0x200000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ qcom,vmid = <15>;
+ };
+
+ wlan_mem: wlan-region@8bc00000 {
+ reg = <0x0 0x8bc00000 0x0 0x180000>;
+ no-map;
+ };
+
+ adsp_mem: adsp-region@96e00000 {
+ reg = <0x0 0x96e00000 0x0 0x1c00000>;
+ no-map;
+ };
+
+ mpss_mem: mpss-region@8d800000 {
+ reg = <0x0 0x8d800000 0x0 0x9600000>;
+ no-map;
+ };
+
+ gpu_mem: gpu-region@98a00000 {
+ reg = <0x0 0x98a00000 0x0 0x2000>;
+ no-map;
+ };
+
+ reserved-region@9a500000 {
+ reg = <0x0 0x9a500000 0x0 0x600000>;
+ no-map;
+ };
+ };
+
+ vreg_nvme_0p9: nvme-0p9-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_nvme_0p9";
+
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-always-on;
+ };
+
+ vreg_nvme_3p3: nvme-3p3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_nvme_3p3";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pmc8180c_gpios 11 0>;
+ enable-active-high;
+
+ regulator-always-on;
+ };
+
+ vdd_kb_tp_3v3: vdd-kb-tp-3v3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_kb_tp_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ regulator-always-on;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&kb_tp_3v3_en_active_state>;
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ };
+
+ vreg_s4a_1p8: pm8150-s4 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_s4a_1p8";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+
+ vin-supply = <&vph_pwr>;
+ };
+};
+
+&apps_rsc {
+ pmc8180-a-rpmh-regulators {
+ compatible = "qcom,pmc8180-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p0>;
+
+ vreg_s5a_2p0: smps5 {
+ regulator-min-microvolt = <2040000>;
+ regulator-max-microvolt = <2100000>;
+ };
+
+ vreg_l7a_1p8: ldo7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9a_1p3: ldo9 {
+ regulator-min-microvolt = <1296000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12a_1p8: ldo12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ pmc8180c-rpmh-regulators {
+ compatible = "qcom,pmc8180c-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-l2-l3-supply = <&vreg_s6c_1p35>;
+ vdd-bob-supply = <&vph_pwr>;
+
+ vreg_s6c_1p35: smps6 {
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1372000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s8c_1p8: smps8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l3c_1p2: ldo3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4c_3p3: ldo4 {
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10c_3p3: ldo10 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11c_3p3: ldo11 {
+ regulator-min-microvolt = <3296000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_bob: bob {
+ regulator-min-microvolt = <3296000>;
+ regulator-max-microvolt = <3350000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ pmc8180-e-rpmh-regulators {
+ compatible = "qcom,pmc8180-rpmh-regulators";
+ qcom,pmic-id = "e";
+
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-l2-l10-supply = <&vreg_bob>;
+ vdd-l3-l4-l5-l18-supply = <&vreg_s4e_0p98>;
+ vdd-l7-l12-l14-l15-supply = <&vreg_s5e_2p05>;
+ vdd-l13-l16-l17-supply = <&vreg_bob>;
+
+ vreg_s4e_0p98: smps4 {
+ regulator-min-microvolt = <992000>;
+ regulator-max-microvolt = <992000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5e_2p05: smps5 {
+ regulator-min-microvolt = <2040000>;
+ regulator-max-microvolt = <2040000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1e_0p75: ldo1 {
+ regulator-min-microvolt = <752000>;
+ regulator-max-microvolt = <752000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5e_0p88: ldo5 {
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7e_1p8: ldo7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10e_2p9: ldo10 {
+ regulator-min-microvolt = <2904000>;
+ regulator-max-microvolt = <2904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12e: ldo12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l16e_3p0: ldo16 {
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&dispcc {
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+
+ zap-shader {
+ memory-region = <&gpu_mem>;
+ firmware-name = "qcom/sc8180x/qcdxkmsuc8180.mbn";
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_i2c_active_state>;
+
+ status = "okay";
+
+ touchscreen@10 {
+ compatible = "hid-over-i2c";
+ reg = <0x10>;
+ hid-descr-addr = <0x1>;
+
+ vdd-supply = <&vreg_l4c_3p3>;
+ vddl-supply = <&vreg_l12e>;
+
+ post-power-on-delay-ms = <20>;
+
+ interrupts-extended = <&tlmm 122 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_active_state>;
+ };
+};
+
+&i2c7 {
+ clock-frequency = <100000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&aux_i2c_active_state>;
+
+ status = "okay";
+
+ touchpad@15 {
+ compatible = "hid-over-i2c";
+ reg = <0x15>;
+ hid-descr-addr = <0x1>;
+
+ interrupts-extended = <&tlmm 24 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tp_int_active_state>;
+
+ vdd-supply = <&vdd_kb_tp_3v3>;
+ };
+
+ keyboard@3a {
+ compatible = "hid-over-i2c";
+ reg = <0x3a>;
+ hid-descr-addr = <0x1>;
+ interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&kb_int_active_state>;
+
+ vdd-supply = <&vdd_kb_tp_3v3>;
+ };
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_edp {
+ data-lanes = <0 1 2 3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_hpd_active>;
+
+ status = "okay";
+
+ aux-bus {
+ panel {
+ compatible = "edp-panel";
+
+ backlight = <&backlight>;
+
+ ports {
+ port {
+ auo_b133han05_in: endpoint {
+ remote-endpoint = <&mdss_edp_out>;
+ };
+ };
+ };
+ };
+ };
+
+ ports {
+ port@1 {
+ reg = <1>;
+ mdss_edp_out: endpoint {
+ remote-endpoint = <&auo_b133han05_in>;
+ };
+ };
+ };
+};
+
+&pcie1 {
+ perst-gpio = <&tlmm 175 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 177 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie2_default_state>;
+
+ status = "okay";
+};
+
+&pcie1_phy {
+ vdda-phy-supply = <&vreg_l5e_0p88>;
+ vdda-pll-supply = <&vreg_l3c_1p2>;
+
+ status = "okay";
+};
+
+&pmc8180c_lpg {
+ status = "okay";
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&qupv3_id_2 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ memory-region = <&adsp_mem>;
+ firmware-name = "qcom/sc8180x/qcadsp8180.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_mpss {
+ memory-region = <&mpss_mem>;
+ firmware-name = "qcom/sc8180x/qcmpss8180.mbn";
+
+ status = "okay";
+};
+
+&uart12 {
+ compatible = "qcom,geni-debug-uart";
+ status = "okay";
+};
+
+&uart13 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart13_state>;
+
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn3998-bt";
+
+ vddio-supply = <&vreg_s4a_1p8>;
+ vddxo-supply = <&vreg_l7a_1p8>;
+ vddrf-supply = <&vreg_l9a_1p3>;
+ vddch0-supply = <&vreg_l11c_3p3>;
+ max-speed = <3200000>;
+ };
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 190 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l10e_2p9>;
+ vcc-max-microamp = <155000>;
+
+ vccq2-supply = <&vreg_l7e_1p8>;
+ vccq2-max-microamp = <425000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l5e_0p88>;
+ vdda-pll-supply = <&vreg_l3c_1p2>;
+
+ status = "okay";
+};
+
+&usb_prim_hsphy {
+ vdda-pll-supply = <&vreg_l5e_0p88>;
+ vdda18-supply = <&vreg_l12a_1p8>;
+ vdda33-supply = <&vreg_l16e_3p0>;
+
+ status = "okay";
+};
+
+&usb_prim_qmpphy {
+ vdda-phy-supply = <&vreg_l3c_1p2>;
+ vdda-pll-supply = <&vreg_l5e_0p88>;
+
+ status = "okay";
+};
+
+&usb_prim {
+ status = "okay";
+};
+
+&usb_prim_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_sec_hsphy {
+ vdda-pll-supply = <&vreg_l5e_0p88>;
+ vdda18-supply = <&vreg_l12a_1p8>;
+ vdda33-supply = <&vreg_l16e_3p0>;
+
+ status = "okay";
+};
+
+&usb_sec_qmpphy {
+ vdda-phy-supply = <&vreg_l3c_1p2>;
+ vdda-pll-supply = <&vreg_l5e_0p88>;
+
+ status = "okay";
+};
+
+&usb_sec {
+ status = "okay";
+};
+
+&usb_sec_dwc3 {
+ dr_mode = "host";
+};
+
+&wifi {
+ memory-region = <&wlan_mem>;
+
+ vdd-0.8-cx-mx-supply = <&vreg_l1e_0p75>;
+ vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+ vdd-1.3-rfa-supply = <&vreg_l9a_1p3>;
+ vdd-3.3-ch0-supply = <&vreg_l11c_3p3>;
+ vdd-3.3-ch1-supply = <&vreg_l10c_3p3>;
+
+ status = "okay";
+};
+
+&xo_board_clk {
+ clock-frequency = <38400000>;
+};
+
+/* PINCTRL */
+
+&pmc8180c_gpios {
+ bl_pwm_default_state: bl-pwm-default-state {
+ en {
+ pins = "gpio8";
+ function = "normal";
+ };
+
+ pwm {
+ pins = "gpio10";
+ function = "func1";
+ };
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <47 4>, <126 4>;
+
+ aux_i2c_active_state: aux-i2c-active-state {
+ pins = "gpio98", "gpio99";
+ function = "qup7";
+
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ edp_hpd_active: epd-hpd-active-state {
+ pins = "gpio10";
+ function = "edp_hot";
+ };
+
+ hall_int_active_state: hall-int-active-state {
+ pins = "gpio121";
+ function = "gpio";
+
+ input-enable;
+ bias-disable;
+ };
+
+ kb_int_active_state: kb-int-active-state {
+ int-n {
+ pins = "gpio37";
+ function = "gpio";
+
+ bias-pull-up;
+ intput-enable;
+ };
+
+ kp-disable {
+ pins = "gpio135";
+ function = "gpio";
+
+ output-high;
+ };
+ };
+
+ kb_tp_3v3_en_active_state: kb-tp-3v3-en-active-state {
+ pins = "gpio4";
+ function = "gpio";
+
+ bias-disable;
+ };
+
+ pcie2_default_state: pcie2-default-state {
+ clkreq {
+ pins = "gpio176";
+ function = "pci_e2";
+ bias-pull-up;
+ };
+
+ reset-n {
+ pins = "gpio175";
+ function = "gpio";
+
+ drive-strength = <2>;
+ output-low;
+ bias-pull-down;
+ };
+
+ wake-n {
+ pins = "gpio177";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ tp_int_active_state: tp-int-active-state {
+ tp-int {
+ pins = "gpio24";
+ function = "gpio";
+
+ bias-disable;
+ input-enable;
+ };
+
+ tp-close-n {
+ pins = "gpio116";
+ function = "gpio";
+
+ bias-disable;
+ input-enable;
+ };
+ };
+
+ ts_active_state: ts-active-state {
+ int-n {
+ pins = "gpio122";
+ function = "gpio";
+
+ input-enable;
+ bias-disable;
+ };
+
+ reset-n {
+ pins = "gpio54";
+ function = "gpio";
+
+ output-high;
+ };
+ };
+
+ ts_i2c_active_state: ts-i2c-active-state {
+ pins = "gpio114", "gpio115";
+ function = "qup1";
+
+ /* External pull up */
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ uart13_state: uart13-state {
+ cts {
+ pins = "gpio43";
+ function = "qup13";
+ bias-pull-down;
+ };
+
+ rts-tx {
+ pins = "gpio44", "gpio45";
+ function = "qup13";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rx {
+ pins = "gpio46";
+ function = "qup13";
+ bias-pull-up;
+ };
+ };
+};
--
2.37.3
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 6/6] arm64: dts: qcom: sc8180x: Introduce Lenovo Flex 5G
2022-09-16 12:11 [PATCH 0/6] Introduce the SC8180x devices Vinod Koul
` (4 preceding siblings ...)
2022-09-16 12:12 ` [PATCH 5/6] arm64: dts: qcom: sc8180x: Introduce Primus Vinod Koul
@ 2022-09-16 12:12 ` Vinod Koul
2022-09-16 12:26 ` Dmitry Baryshkov
2022-09-17 16:35 ` Krzysztof Kozlowski
5 siblings, 2 replies; 14+ messages in thread
From: Vinod Koul @ 2022-09-16 12:12 UTC (permalink / raw)
To: Bjorn Andersson
Cc: linux-arm-msm, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
devicetree, linux-kernel, Vinod Koul
From: Bjorn Andersson <bjorn.andersson@linaro.org>
Introduce support for the Lenovo Flex 5G laptop, built on the Qualcomm
SC8180X platform. Supported peripherals includes keyboard, touchpad,
UFS storage, external USB and WiFi.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../boot/dts/qcom/sc8180x-lenovo-flex-5g.dts | 590 ++++++++++++++++++
2 files changed, 591 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index f1c620bb078e..a9de6f50ca37 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -112,6 +112,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-villager-r1-lte.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp2.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-crd-r3.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sc8180x-lenovo-flex-5g.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc8180x-primus.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-crd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-lenovo-thinkpad-x13s.dtb
diff --git a/arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts b/arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts
new file mode 100644
index 000000000000..559a1fb6173f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts
@@ -0,0 +1,590 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020-2022, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sc8180x.dtsi"
+#include "sc8180x-pmics.dtsi"
+
+/ {
+ model = "Lenovo Flex 5G";
+ compatible = "lenovo,flex-5g", "qcom,sc8180x";
+
+ aliases {
+ serial0 = &uart13;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pmc8180c_lpg 4 1000000>;
+ enable-gpios = <&pmc8180c_gpios 8 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_pwm_default_state>;
+ };
+
+ chosen {
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&hall_int_active_state>;
+
+ lid {
+ gpios = <&tlmm 121 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ wakeup-source;
+ wakeup-event-action = <EV_ACT_DEASSERTED>;
+ };
+ };
+
+ reserved-memory {
+ rmtfs_mem: rmtfs-region@85500000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0x0 0x85500000 0x0 0x200000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ qcom,vmid = <15>;
+ };
+
+ wlan_mem: wlan-region@8bc00000 {
+ reg = <0x0 0x8bc00000 0x0 0x180000>;
+ no-map;
+ };
+
+ mpss_mem: mpss-region@8d800000 {
+ reg = <0x0 0x8d800000 0x0 0x3000000>;
+ no-map;
+ };
+
+ adsp_mem: adsp-region@90800000 {
+ reg = <0x0 0x90800000 0x0 0x1c00000>;
+ no-map;
+ };
+
+ gpu_mem: gpu-region@98715000 {
+ reg = <0x0 0x98715000 0x0 0x2000>;
+ no-map;
+ };
+
+ cdsp_mem: cdsp-region@98900000 {
+ reg = <0x0 0x98900000 0x0 0x1400000>;
+ no-map;
+ };
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ };
+
+ vreg_s4a_1p8: pm8150-s4 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_s4a_1p8";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+
+ vin-supply = <&vph_pwr>;
+ };
+};
+
+&apps_rsc {
+ pmc8180-a-rpmh-regulators {
+ compatible = "qcom,pmc8180-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p0>;
+
+ vreg_s5a_2p0: smps5 {
+ regulator-min-microvolt = <2040000>;
+ regulator-max-microvolt = <2100000>;
+ };
+
+ vreg_l7a_1p8: ldo7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9a_1p3: ldo9 {
+ regulator-min-microvolt = <1296000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12a_1p8: ldo12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ pmc8180c-rpmh-regulators {
+ compatible = "qcom,pmc8180c-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-l2-l3-supply = <&vreg_s6c_1p35>;
+ vdd-bob-supply = <&vph_pwr>;
+
+ vreg_s6c_1p35: smps6 {
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1372000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3c_1p2: ldo3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10c_3p3: ldo10 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11c_3p3: ldo11 {
+ regulator-min-microvolt = <3296000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_bob: bob {
+ regulator-min-microvolt = <3296000>;
+ regulator-max-microvolt = <3350000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ pmc8180-e-rpmh-regulators {
+ compatible = "qcom,pmc8180-rpmh-regulators";
+ qcom,pmic-id = "e";
+
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-l2-l10-supply = <&vreg_bob>;
+ vdd-l3-l4-l5-l18-supply = <&vreg_s4e_0p98>;
+ vdd-l7-l12-l14-l15-supply = <&vreg_s5e_2p05>;
+ vdd-l13-l16-l17-supply = <&vreg_bob>;
+
+ vreg_s4e_0p98: smps4 {
+ regulator-min-microvolt = <992000>;
+ regulator-max-microvolt = <992000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5e_2p05: smps5 {
+ regulator-min-microvolt = <2040000>;
+ regulator-max-microvolt = <2040000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1e_0p75: ldo1 {
+ regulator-min-microvolt = <752000>;
+ regulator-max-microvolt = <752000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5e_0p88: ldo5 {
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7e_1p8: ldo7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10e_2p9: ldo10 {
+ regulator-min-microvolt = <2904000>;
+ regulator-max-microvolt = <2904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l16e_3p0: ldo16 {
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&dispcc {
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+
+ zap-shader {
+ memory-region = <&gpu_mem>;
+ firmware-name = "qcom/sc8180x/qcdxkmsuc8180.mbn";
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_active>, <&i2c1_hid_active>;
+
+ status = "okay";
+
+ hid@10 {
+ compatible = "hid-over-i2c";
+ reg = <0x10>;
+ hid-descr-addr = <0x1>;
+
+ interrupts-extended = <&tlmm 122 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&i2c7 {
+ clock-frequency = <100000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c7_active>, <&i2c7_hid_active>;
+
+ status = "okay";
+
+ hid@5 {
+ compatible = "hid-over-i2c";
+ reg = <0x5>;
+ hid-descr-addr = <0x20>;
+
+ interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ hid@2c {
+ compatible = "hid-over-i2c";
+ reg = <0x2c>;
+ hid-descr-addr = <0x20>;
+
+ interrupts-extended = <&tlmm 24 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_edp {
+ data-lanes = <0 1 2 3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_hpd_active>;
+
+ status = "okay";
+
+ aux-bus {
+ panel {
+ compatible = "edp-panel";
+ no-hpd;
+
+ backlight = <&backlight>;
+
+ ports {
+ port {
+ auo_b140han06_in: endpoint {
+ remote-endpoint = <&mdss_edp_out>;
+ };
+ };
+ };
+ };
+ };
+
+ ports {
+ port@1 {
+ reg = <1>;
+ mdss_edp_out: endpoint {
+ remote-endpoint = <&auo_b140han06_in>;
+ };
+ };
+ };
+};
+
+&pcie3 {
+ perst-gpio = <&tlmm 178 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 180 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie3_default_state>;
+
+ status = "okay";
+};
+
+&pcie3_phy {
+ vdda-phy-supply = <&vreg_l5e_0p88>;
+ vdda-pll-supply = <&vreg_l3c_1p2>;
+
+ status = "okay";
+};
+
+&pmc8180c_lpg {
+ status = "okay";
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&qupv3_id_2 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ memory-region = <&adsp_mem>;
+ firmware-name = "qcom/sc8180x/qcadsp8180.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ memory-region = <&cdsp_mem>;
+ firmware-name = "qcom/sc8180x/qccdsp8180.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_mpss {
+ memory-region = <&mpss_mem>;
+ firmware-name = "qcom/sc8180x/qcmpss8180_nm.mbn";
+
+ status = "okay";
+};
+
+&uart13 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart13_state>;
+
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn3998-bt";
+
+ vddio-supply = <&vreg_s4a_1p8>;
+ vddxo-supply = <&vreg_l7a_1p8>;
+ vddrf-supply = <&vreg_l9a_1p3>;
+ vddch0-supply = <&vreg_l11c_3p3>;
+ max-speed = <3200000>;
+ };
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 190 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l10e_2p9>;
+ vcc-max-microamp = <155000>;
+
+ vccq2-supply = <&vreg_l7e_1p8>;
+ vccq2-max-microamp = <425000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l5e_0p88>;
+ vdda-pll-supply = <&vreg_l3c_1p2>;
+
+ status = "okay";
+};
+
+&usb_prim_hsphy {
+ vdda-pll-supply = <&vreg_l5e_0p88>;
+ vdda18-supply = <&vreg_l12a_1p8>;
+ vdda33-supply = <&vreg_l16e_3p0>;
+
+ status = "okay";
+};
+
+&usb_prim_qmpphy {
+ vdda-phy-supply = <&vreg_l3c_1p2>;
+ vdda-pll-supply = <&vreg_l5e_0p88>;
+
+ status = "okay";
+};
+
+&usb_prim {
+ status = "okay";
+};
+
+&usb_prim_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_sec_hsphy {
+ vdda-pll-supply = <&vreg_l5e_0p88>;
+ vdda18-supply = <&vreg_l12a_1p8>;
+ vdda33-supply = <&vreg_l16e_3p0>;
+
+ status = "okay";
+};
+
+&usb_sec_qmpphy {
+ vdda-phy-supply = <&vreg_l3c_1p2>;
+ vdda-pll-supply = <&vreg_l5e_0p88>;
+
+ status = "okay";
+};
+
+&usb_sec {
+ status = "okay";
+};
+
+&usb_sec_dwc3 {
+ dr_mode = "host";
+};
+
+&wifi {
+ memory-region = <&wlan_mem>;
+
+ vdd-0.8-cx-mx-supply = <&vreg_l1e_0p75>;
+ vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+ vdd-1.3-rfa-supply = <&vreg_l9a_1p3>;
+ vdd-3.3-ch0-supply = <&vreg_l11c_3p3>;
+ vdd-3.3-ch1-supply = <&vreg_l10c_3p3>;
+
+ status = "okay";
+};
+
+&xo_board_clk {
+ clock-frequency = <38400000>;
+};
+
+/* PINCTRL */
+
+&pmc8180c_gpios {
+ bl_pwm_default_state: bl-pwm-default-state {
+ en {
+ pins = "gpio8";
+ function = "normal";
+ };
+
+ pwm {
+ pins = "gpio10";
+ function = "func1";
+ };
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <47 4>, <126 4>;
+
+ edp_hpd_active: epd-hpd-active-state {
+ pins = "gpio10";
+ function = "edp_hot";
+ };
+
+ hall_int_active_state: hall-int-active-state {
+ pins = "gpio121";
+ function = "gpio";
+
+ input-enable;
+ bias-disable;
+ };
+
+ i2c1_active: i2c1-active-state {
+ pins = "gpio114", "gpio115";
+ function = "qup1";
+
+ bias-pull-up = <1>;
+ drive-strength = <2>;
+ };
+
+ i2c1_hid_active: i2c1-hid-active-state {
+ pins = "gpio122";
+ function = "gpio";
+
+ input-enable;
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ i2c7_active: i2c7-active-state {
+ pins = "gpio98", "gpio99";
+ function = "qup7";
+
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ i2c7_hid_active: i2c7-hid-active-state {
+ pins = "gpio37", "gpio24";
+ function = "gpio";
+
+ input-enable;
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ pcie3_default_state: pcie3-default-state {
+ clkreq {
+ pins = "gpio179";
+ function = "pci_e3";
+ bias-pull-up;
+ };
+
+ reset-n {
+ pins = "gpio178";
+ function = "gpio";
+
+ drive-strength = <2>;
+ output-low;
+ bias-pull-down;
+ };
+
+ wake-n {
+ pins = "gpio180";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ uart13_state: uart13-state {
+ cts {
+ pins = "gpio43";
+ function = "qup13";
+ bias-pull-down;
+ };
+
+ rts-tx {
+ pins = "gpio44", "gpio45";
+ function = "qup13";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rx {
+ pins = "gpio46";
+ function = "qup13";
+ bias-pull-up;
+ };
+ };
+};
--
2.37.3
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH 6/6] arm64: dts: qcom: sc8180x: Introduce Lenovo Flex 5G
2022-09-16 12:12 ` [PATCH 6/6] arm64: dts: qcom: sc8180x: Introduce Lenovo Flex 5G Vinod Koul
@ 2022-09-16 12:26 ` Dmitry Baryshkov
2022-09-16 19:11 ` Bjorn Andersson
2022-09-17 16:35 ` Krzysztof Kozlowski
1 sibling, 1 reply; 14+ messages in thread
From: Dmitry Baryshkov @ 2022-09-16 12:26 UTC (permalink / raw)
To: Vinod Koul
Cc: Bjorn Andersson, linux-arm-msm, Bjorn Andersson, Rob Herring,
Krzysztof Kozlowski, devicetree, linux-kernel
On Fri, 16 Sept 2022 at 15:13, Vinod Koul <vkoul@kernel.org> wrote:
>
> From: Bjorn Andersson <bjorn.andersson@linaro.org>
>
> Introduce support for the Lenovo Flex 5G laptop, built on the Qualcomm
> SC8180X platform. Supported peripherals includes keyboard, touchpad,
> UFS storage, external USB and WiFi.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../boot/dts/qcom/sc8180x-lenovo-flex-5g.dts | 590 ++++++++++++++++++
> 2 files changed, 591 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts
>
[skipped]
> +&gpu {
> + status = "okay";
> +
> + zap-shader {
> + memory-region = <&gpu_mem>;
> + firmware-name = "qcom/sc8180x/qcdxkmsuc8180.mbn";
Is the firmware signed with the test key or with the proper vendor
key? If the latter is true, the firmware should go to the subdir
inside the SoC (I'd suggest following the example and using
sc8180x/LENOVO/dmi_id/)
> + };
> +};
> +
--
With best wishes
Dmitry
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 3/6] dt-bindings: usb: qcom,dwc3: Add SC8180x binding
2022-09-16 12:12 ` [PATCH 3/6] dt-bindings: usb: qcom,dwc3: " Vinod Koul
@ 2022-09-16 12:33 ` Johan Hovold
0 siblings, 0 replies; 14+ messages in thread
From: Johan Hovold @ 2022-09-16 12:33 UTC (permalink / raw)
To: Vinod Koul
Cc: Greg Kroah-Hartman, Bjorn Andersson, linux-arm-msm, Wesley Cheng,
linux-usb, Rob Herring, Krzysztof Kozlowski, devicetree,
linux-kernel
On Fri, Sep 16, 2022 at 05:42:01PM +0530, Vinod Koul wrote:
> Document the USB dwc3 controller for SC8180x SoC
>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
> Documentation/devicetree/bindings/usb/qcom,dwc3.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
> index fea3e7092ace..f33735f3702d 100644
> --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
> +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
> @@ -24,6 +24,7 @@ properties:
> - qcom,qcs404-dwc3
> - qcom,sc7180-dwc3
> - qcom,sc7280-dwc3
> + - qcom,sc8180x-dwc3
> - qcom,sc8280xp-dwc3
> - qcom,sdm660-dwc3
> - qcom,sdm845-dwc3
You need to also describe the clocks and interrupts required by this
platform in the platform-specific sections further down in this file.
Johan
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/6] scsi: ufs: dt-bindings: Add SC8180x binding
2022-09-16 12:12 ` [PATCH 2/6] scsi: ufs: dt-bindings: Add SC8180x binding Vinod Koul
@ 2022-09-16 12:36 ` Johan Hovold
0 siblings, 0 replies; 14+ messages in thread
From: Johan Hovold @ 2022-09-16 12:36 UTC (permalink / raw)
To: Vinod Koul
Cc: Martin K . Petersen, Bjorn Andersson, linux-arm-msm, Alim Akhtar,
Avri Altman, Bart Van Assche, linux-scsi, Rob Herring,
Krzysztof Kozlowski, devicetree, linux-kernel
On Fri, Sep 16, 2022 at 05:42:00PM +0530, Vinod Koul wrote:
> Document the UFS HC for SC8180x SoC
>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
> Documentation/devicetree/bindings/ufs/qcom,ufs.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/ufs/qcom,ufs.yaml b/Documentation/devicetree/bindings/ufs/qcom,ufs.yaml
> index f2d6298d926c..dd0256357247 100644
> --- a/Documentation/devicetree/bindings/ufs/qcom,ufs.yaml
> +++ b/Documentation/devicetree/bindings/ufs/qcom,ufs.yaml
> @@ -26,6 +26,7 @@ properties:
> - qcom,msm8994-ufshc
> - qcom,msm8996-ufshc
> - qcom,msm8998-ufshc
> + - qcom,sc8180x-ufshc
> - qcom,sc8280xp-ufshc
> - qcom,sdm845-ufshc
> - qcom,sm6350-ufshc
Same here, you need to describe the required clocks in the sections
below.
Johan
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 6/6] arm64: dts: qcom: sc8180x: Introduce Lenovo Flex 5G
2022-09-16 12:26 ` Dmitry Baryshkov
@ 2022-09-16 19:11 ` Bjorn Andersson
0 siblings, 0 replies; 14+ messages in thread
From: Bjorn Andersson @ 2022-09-16 19:11 UTC (permalink / raw)
To: Dmitry Baryshkov
Cc: Vinod Koul, linux-arm-msm, Bjorn Andersson, Rob Herring,
Krzysztof Kozlowski, devicetree, linux-kernel
On Fri, Sep 16, 2022 at 03:26:59PM +0300, Dmitry Baryshkov wrote:
> On Fri, 16 Sept 2022 at 15:13, Vinod Koul <vkoul@kernel.org> wrote:
> >
> > From: Bjorn Andersson <bjorn.andersson@linaro.org>
> >
> > Introduce support for the Lenovo Flex 5G laptop, built on the Qualcomm
> > SC8180X platform. Supported peripherals includes keyboard, touchpad,
> > UFS storage, external USB and WiFi.
> >
> > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> > Signed-off-by: Vinod Koul <vkoul@kernel.org>
> > ---
> > arch/arm64/boot/dts/qcom/Makefile | 1 +
> > .../boot/dts/qcom/sc8180x-lenovo-flex-5g.dts | 590 ++++++++++++++++++
> > 2 files changed, 591 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts
> >
>
> [skipped]
>
> > +&gpu {
> > + status = "okay";
> > +
> > + zap-shader {
> > + memory-region = <&gpu_mem>;
> > + firmware-name = "qcom/sc8180x/qcdxkmsuc8180.mbn";
>
> Is the firmware signed with the test key or with the proper vendor
> key? If the latter is true, the firmware should go to the subdir
> inside the SoC (I'd suggest following the example and using
> sc8180x/LENOVO/dmi_id/)
>
Correct, this and the remoteprocs should be pointed to
qcom/sc8180x/LENOVO/82AK/
Regards,
Bjorn
> > + };
> > +};
> > +
>
> --
> With best wishes
> Dmitry
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/6] dt-bindings: firmware: document Qualcomm SC8180x SCM
2022-09-16 12:11 ` [PATCH 1/6] dt-bindings: firmware: document Qualcomm SC8180x SCM Vinod Koul
@ 2022-09-17 16:29 ` Krzysztof Kozlowski
0 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-09-17 16:29 UTC (permalink / raw)
To: Vinod Koul, Bjorn Andersson
Cc: linux-arm-msm, Rob Herring, Krzysztof Kozlowski, devicetree,
linux-kernel
On 16/09/2022 13:11, Vinod Koul wrote:
> Document the compatible for Qualcomm SC8180x SCM
>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 6/6] arm64: dts: qcom: sc8180x: Introduce Lenovo Flex 5G
2022-09-16 12:12 ` [PATCH 6/6] arm64: dts: qcom: sc8180x: Introduce Lenovo Flex 5G Vinod Koul
2022-09-16 12:26 ` Dmitry Baryshkov
@ 2022-09-17 16:35 ` Krzysztof Kozlowski
1 sibling, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-09-17 16:35 UTC (permalink / raw)
To: Vinod Koul, Bjorn Andersson
Cc: linux-arm-msm, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
devicetree, linux-kernel
On 16/09/2022 13:12, Vinod Koul wrote:
> From: Bjorn Andersson <bjorn.andersson@linaro.org>
>
> Introduce support for the Lenovo Flex 5G laptop, built on the Qualcomm
> SC8180X platform. Supported peripherals includes keyboard, touchpad,
> UFS storage, external USB and WiFi.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../boot/dts/qcom/sc8180x-lenovo-flex-5g.dts | 590 ++++++++++++++++++
> 2 files changed, 591 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index f1c620bb078e..a9de6f50ca37 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -112,6 +112,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-villager-r1-lte.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp2.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc7280-crd-r3.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sc8180x-lenovo-flex-5g.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc8180x-primus.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-crd.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-lenovo-thinkpad-x13s.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts b/arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts
> new file mode 100644
> index 000000000000..559a1fb6173f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts
> @@ -0,0 +1,590 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2020-2022, Linaro Limited
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/gpio-keys.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +#include "sc8180x.dtsi"
> +#include "sc8180x-pmics.dtsi"
> +
> +/ {
> + model = "Lenovo Flex 5G";
> + compatible = "lenovo,flex-5g", "qcom,sc8180x";
> +
> + aliases {
> + serial0 = &uart13;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pmc8180c_lpg 4 1000000>;
> + enable-gpios = <&pmc8180c_gpios 8 GPIO_ACTIVE_HIGH>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&bl_pwm_default_state>;
> + };
> +
> + chosen {
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&hall_int_active_state>;
> +
> + lid {
Does not look like you tested the DTS against bindings. Please run `make
dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
for instructions).
> + gpios = <&tlmm 121 GPIO_ACTIVE_LOW>;
> + linux,input-type = <EV_SW>;
> + linux,code = <SW_LID>;
> + wakeup-source;
> + wakeup-event-action = <EV_ACT_DEASSERTED>;
> + };
> + };
> +
> + reserved-memory {
> + rmtfs_mem: rmtfs-region@85500000 {
> + compatible = "qcom,rmtfs-mem";
> + reg = <0x0 0x85500000 0x0 0x200000>;
> + no-map;
> +
> + qcom,client-id = <1>;
> + qcom,vmid = <15>;
> + };
> +
> + wlan_mem: wlan-region@8bc00000 {
> + reg = <0x0 0x8bc00000 0x0 0x180000>;
> + no-map;
> + };
> +
> + mpss_mem: mpss-region@8d800000 {
> + reg = <0x0 0x8d800000 0x0 0x3000000>;
> + no-map;
> + };
> +
> + adsp_mem: adsp-region@90800000 {
> + reg = <0x0 0x90800000 0x0 0x1c00000>;
> + no-map;
> + };
> +
> + gpu_mem: gpu-region@98715000 {
> + reg = <0x0 0x98715000 0x0 0x2000>;
> + no-map;
> + };
> +
> + cdsp_mem: cdsp-region@98900000 {
> + reg = <0x0 0x98900000 0x0 0x1400000>;
> + no-map;
> + };
> + };
> +
> + vph_pwr: vph-pwr-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vph_pwr";
> + regulator-min-microvolt = <3700000>;
> + regulator-max-microvolt = <3700000>;
> + };
> +
> + vreg_s4a_1p8: pm8150-s4 {
Use consistent naming, so for example "regulator" suffix in node names.
> + compatible = "regulator-fixed";
> + regulator-name = "vreg_s4a_1p8";
> +
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> +
> + regulator-always-on;
> + regulator-boot-on;
> +
> + vin-supply = <&vph_pwr>;
> + };
> +};
> +
> +&apps_rsc {
> + pmc8180-a-rpmh-regulators {
> + compatible = "qcom,pmc8180-rpmh-regulators";
Undocumented compatible.
> + qcom,pmic-id = "a";
> +
> + vdd-s5-supply = <&vph_pwr>;
> + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p0>;
> +
> + vreg_s5a_2p0: smps5 {
> + regulator-min-microvolt = <2040000>;
> + regulator-max-microvolt = <2100000>;
> + };
> +
> + vreg_l7a_1p8: ldo7 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l9a_1p3: ldo9 {
> + regulator-min-microvolt = <1296000>;
> + regulator-max-microvolt = <1304000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l12a_1p8: ldo12 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + pmc8180c-rpmh-regulators {
> + compatible = "qcom,pmc8180c-rpmh-regulators";
Same problem.
> + qcom,pmic-id = "c";
> +
> + vdd-s6-supply = <&vph_pwr>;
> + vdd-l2-l3-supply = <&vreg_s6c_1p35>;
> + vdd-bob-supply = <&vph_pwr>;
> +
> + vreg_s6c_1p35: smps6 {
> + regulator-min-microvolt = <1350000>;
> + regulator-max-microvolt = <1372000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l3c_1p2: ldo3 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l10c_3p3: ldo10 {
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3312000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l11c_3p3: ldo11 {
> + regulator-min-microvolt = <3296000>;
> + regulator-max-microvolt = <3304000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_bob: bob {
> + regulator-min-microvolt = <3296000>;
> + regulator-max-microvolt = <3350000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + pmc8180-e-rpmh-regulators {
> + compatible = "qcom,pmc8180-rpmh-regulators";
> + qcom,pmic-id = "e";
> +
> + vdd-s4-supply = <&vph_pwr>;
> + vdd-s5-supply = <&vph_pwr>;
> + vdd-l2-l10-supply = <&vreg_bob>;
> + vdd-l3-l4-l5-l18-supply = <&vreg_s4e_0p98>;
> + vdd-l7-l12-l14-l15-supply = <&vreg_s5e_2p05>;
> + vdd-l13-l16-l17-supply = <&vreg_bob>;
> +
> + vreg_s4e_0p98: smps4 {
> + regulator-min-microvolt = <992000>;
> + regulator-max-microvolt = <992000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s5e_2p05: smps5 {
> + regulator-min-microvolt = <2040000>;
> + regulator-max-microvolt = <2040000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l1e_0p75: ldo1 {
> + regulator-min-microvolt = <752000>;
> + regulator-max-microvolt = <752000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l5e_0p88: ldo5 {
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <880000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l7e_1p8: ldo7 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l10e_2p9: ldo10 {
> + regulator-min-microvolt = <2904000>;
> + regulator-max-microvolt = <2904000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l16e_3p0: ldo16 {
> + regulator-min-microvolt = <3072000>;
> + regulator-max-microvolt = <3072000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +};
> +
> +&dispcc {
> + status = "okay";
> +};
> +
> +&gpu {
> + status = "okay";
> +
> + zap-shader {
> + memory-region = <&gpu_mem>;
> + firmware-name = "qcom/sc8180x/qcdxkmsuc8180.mbn";
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_active>, <&i2c1_hid_active>;
> +
> + status = "okay";
> +
> + hid@10 {
> + compatible = "hid-over-i2c";
> + reg = <0x10>;
> + hid-descr-addr = <0x1>;
> +
> + interrupts-extended = <&tlmm 122 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +&i2c7 {
> + clock-frequency = <100000>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c7_active>, <&i2c7_hid_active>;
> +
> + status = "okay";
> +
> + hid@5 {
> + compatible = "hid-over-i2c";
> + reg = <0x5>;
> + hid-descr-addr = <0x20>;
> +
> + interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + hid@2c {
> + compatible = "hid-over-i2c";
> + reg = <0x2c>;
> + hid-descr-addr = <0x20>;
> +
> + interrupts-extended = <&tlmm 24 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +&mdss {
> + status = "okay";
> +};
> +
> +&mdss_edp {
> + data-lanes = <0 1 2 3>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&edp_hpd_active>;
> +
> + status = "okay";
> +
> + aux-bus {
> + panel {
> + compatible = "edp-panel";
> + no-hpd;
> +
> + backlight = <&backlight>;
> +
> + ports {
> + port {
> + auo_b140han06_in: endpoint {
> + remote-endpoint = <&mdss_edp_out>;
> + };
> + };
> + };
> + };
> + };
> +
> + ports {
> + port@1 {
> + reg = <1>;
> + mdss_edp_out: endpoint {
> + remote-endpoint = <&auo_b140han06_in>;
> + };
> + };
> + };
> +};
> +
> +&pcie3 {
> + perst-gpio = <&tlmm 178 GPIO_ACTIVE_LOW>;
> + wake-gpio = <&tlmm 180 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie3_default_state>;
> +
> + status = "okay";
> +};
> +
> +&pcie3_phy {
> + vdda-phy-supply = <&vreg_l5e_0p88>;
> + vdda-pll-supply = <&vreg_l3c_1p2>;
> +
> + status = "okay";
> +};
> +
> +&pmc8180c_lpg {
> + status = "okay";
> +};
> +
> +&qupv3_id_0 {
> + status = "okay";
> +};
> +
> +&qupv3_id_1 {
> + status = "okay";
> +};
> +
> +&qupv3_id_2 {
> + status = "okay";
> +};
> +
> +&remoteproc_adsp {
> + memory-region = <&adsp_mem>;
> + firmware-name = "qcom/sc8180x/qcadsp8180.mbn";
> +
> + status = "okay";
> +};
> +
> +&remoteproc_cdsp {
> + memory-region = <&cdsp_mem>;
> + firmware-name = "qcom/sc8180x/qccdsp8180.mbn";
> +
> + status = "okay";
> +};
> +
> +&remoteproc_mpss {
> + memory-region = <&mpss_mem>;
> + firmware-name = "qcom/sc8180x/qcmpss8180_nm.mbn";
> +
> + status = "okay";
> +};
> +
> +&uart13 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart13_state>;
> +
> + status = "okay";
> +
> + bluetooth {
> + compatible = "qcom,wcn3998-bt";
> +
> + vddio-supply = <&vreg_s4a_1p8>;
> + vddxo-supply = <&vreg_l7a_1p8>;
> + vddrf-supply = <&vreg_l9a_1p3>;
> + vddch0-supply = <&vreg_l11c_3p3>;
> + max-speed = <3200000>;
> + };
> +};
> +
> +&ufs_mem_hc {
> + reset-gpios = <&tlmm 190 GPIO_ACTIVE_LOW>;
> +
> + vcc-supply = <&vreg_l10e_2p9>;
> + vcc-max-microamp = <155000>;
> +
> + vccq2-supply = <&vreg_l7e_1p8>;
> + vccq2-max-microamp = <425000>;
> +
> + status = "okay";
> +};
> +
> +&ufs_mem_phy {
> + vdda-phy-supply = <&vreg_l5e_0p88>;
> + vdda-pll-supply = <&vreg_l3c_1p2>;
> +
> + status = "okay";
> +};
> +
> +&usb_prim_hsphy {
> + vdda-pll-supply = <&vreg_l5e_0p88>;
> + vdda18-supply = <&vreg_l12a_1p8>;
> + vdda33-supply = <&vreg_l16e_3p0>;
> +
> + status = "okay";
> +};
> +
> +&usb_prim_qmpphy {
> + vdda-phy-supply = <&vreg_l3c_1p2>;
> + vdda-pll-supply = <&vreg_l5e_0p88>;
> +
> + status = "okay";
> +};
> +
> +&usb_prim {
> + status = "okay";
> +};
> +
> +&usb_prim_dwc3 {
> + dr_mode = "host";
> +};
> +
> +&usb_sec_hsphy {
> + vdda-pll-supply = <&vreg_l5e_0p88>;
> + vdda18-supply = <&vreg_l12a_1p8>;
> + vdda33-supply = <&vreg_l16e_3p0>;
> +
> + status = "okay";
> +};
> +
> +&usb_sec_qmpphy {
> + vdda-phy-supply = <&vreg_l3c_1p2>;
> + vdda-pll-supply = <&vreg_l5e_0p88>;
> +
> + status = "okay";
> +};
> +
> +&usb_sec {
> + status = "okay";
> +};
> +
> +&usb_sec_dwc3 {
> + dr_mode = "host";
> +};
> +
> +&wifi {
> + memory-region = <&wlan_mem>;
> +
> + vdd-0.8-cx-mx-supply = <&vreg_l1e_0p75>;
> + vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
> + vdd-1.3-rfa-supply = <&vreg_l9a_1p3>;
> + vdd-3.3-ch0-supply = <&vreg_l11c_3p3>;
> + vdd-3.3-ch1-supply = <&vreg_l10c_3p3>;
> +
> + status = "okay";
> +};
> +
> +&xo_board_clk {
> + clock-frequency = <38400000>;
> +};
> +
> +/* PINCTRL */
> +
> +&pmc8180c_gpios {
> + bl_pwm_default_state: bl-pwm-default-state {
> + en {
This does not look like matching bindings. Did it pass dtbs_check?
> + pins = "gpio8";
> + function = "normal";
> + };
> +
> + pwm {
> + pins = "gpio10";
> + function = "func1";
> + };
> + };
> +};
> +
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 5/6] arm64: dts: qcom: sc8180x: Introduce Primus
2022-09-16 12:12 ` [PATCH 5/6] arm64: dts: qcom: sc8180x: Introduce Primus Vinod Koul
@ 2022-09-17 16:36 ` Krzysztof Kozlowski
0 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-09-17 16:36 UTC (permalink / raw)
To: Vinod Koul, Bjorn Andersson
Cc: linux-arm-msm, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
devicetree, linux-kernel
On 16/09/2022 13:12, Vinod Koul wrote:
> From: Bjorn Andersson <bjorn.andersson@linaro.org>
>
> Introduce support for the SC8180X reference device, aka Primus, with
> debug UART, regulators, UFS and USB support.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
(...)
> +&wifi {
> + memory-region = <&wlan_mem>;
> +
> + vdd-0.8-cx-mx-supply = <&vreg_l1e_0p75>;
> + vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
> + vdd-1.3-rfa-supply = <&vreg_l9a_1p3>;
> + vdd-3.3-ch0-supply = <&vreg_l11c_3p3>;
> + vdd-3.3-ch1-supply = <&vreg_l10c_3p3>;
> +
> + status = "okay";
> +};
> +
> +&xo_board_clk {
> + clock-frequency = <38400000>;
> +};
> +
> +/* PINCTRL */
> +
> +&pmc8180c_gpios {
> + bl_pwm_default_state: bl-pwm-default-state {
> + en {
Suffix -pins
> + pins = "gpio8";
> + function = "normal";
> + };
> +
> + pwm {
Suffix -pins
> + pins = "gpio10";
> + function = "func1";
> + };
> + };
> +};
> +
> +&tlmm {
> + gpio-reserved-ranges = <0 4>, <47 4>, <126 4>;
> +
> + aux_i2c_active_state: aux-i2c-active-state {
> + pins = "gpio98", "gpio99";
> + function = "qup7";
> +
> + bias-disable;
> + drive-strength = <16>;
> + };
> +
> + edp_hpd_active: epd-hpd-active-state {
> + pins = "gpio10";
> + function = "edp_hot";
> + };
> +
> + hall_int_active_state: hall-int-active-state {
> + pins = "gpio121";
> + function = "gpio";
> +
> + input-enable;
> + bias-disable;
> + };
> +
> + kb_int_active_state: kb-int-active-state {
> + int-n {
Suffix -pins
> + pins = "gpio37";
> + function = "gpio";
> +
> + bias-pull-up;
> + intput-enable;
> + };
> +
> + kp-disable {
Suffix -pins
> + pins = "gpio135";
> + function = "gpio";
> +
> + output-high;
> + };
> + };
> +
> + kb_tp_3v3_en_active_state: kb-tp-3v3-en-active-state {
> + pins = "gpio4";
> + function = "gpio";
> +
> + bias-disable;
> + };
> +
> + pcie2_default_state: pcie2-default-state {
> + clkreq {
Suffix -pins
> + pins = "gpio176";
> + function = "pci_e2";
> + bias-pull-up;
> + };
> +
> + reset-n {
Suffix -pins
> + pins = "gpio175";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + output-low;
> + bias-pull-down;
> + };
> +
> + wake-n {
Suffix -pins
> + pins = "gpio177";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> + };
> +
> + tp_int_active_state: tp-int-active-state {
> + tp-int {
Suffix -pins
> + pins = "gpio24";
> + function = "gpio";
> +
> + bias-disable;
> + input-enable;
> + };
> +
> + tp-close-n {
Suffix -pins
> + pins = "gpio116";
> + function = "gpio";
> +
> + bias-disable;
> + input-enable;
> + };
> + };
> +
> + ts_active_state: ts-active-state {
> + int-n {
Suffix -pins
> + pins = "gpio122";
> + function = "gpio";
> +
> + input-enable;
> + bias-disable;
> + };
> +
> + reset-n {
Suffix -pins
> + pins = "gpio54";
> + function = "gpio";
> +
> + output-high;
> + };
> + };
> +
> + ts_i2c_active_state: ts-i2c-active-state {
> + pins = "gpio114", "gpio115";
> + function = "qup1";
> +
> + /* External pull up */
> + bias-disable;
> + drive-strength = <2>;
> + };
> +
> + uart13_state: uart13-state {
> + cts {
Suffix -pins
> + pins = "gpio43";
> + function = "qup13";
> + bias-pull-down;
> + };
> +
> + rts-tx {
Suffix -pins
> + pins = "gpio44", "gpio45";
> + function = "qup13";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + rx {
Suffix -pins
> + pins = "gpio46";
> + function = "qup13";
> + bias-pull-up;
> + };
> + };
> +};
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2022-09-17 16:36 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-09-16 12:11 [PATCH 0/6] Introduce the SC8180x devices Vinod Koul
2022-09-16 12:11 ` [PATCH 1/6] dt-bindings: firmware: document Qualcomm SC8180x SCM Vinod Koul
2022-09-17 16:29 ` Krzysztof Kozlowski
2022-09-16 12:12 ` [PATCH 2/6] scsi: ufs: dt-bindings: Add SC8180x binding Vinod Koul
2022-09-16 12:36 ` Johan Hovold
2022-09-16 12:12 ` [PATCH 3/6] dt-bindings: usb: qcom,dwc3: " Vinod Koul
2022-09-16 12:33 ` Johan Hovold
2022-09-16 12:12 ` [PATCH 4/6] arm64: dts: qcom: Introduce the SC8180x platform Vinod Koul
2022-09-16 12:12 ` [PATCH 5/6] arm64: dts: qcom: sc8180x: Introduce Primus Vinod Koul
2022-09-17 16:36 ` Krzysztof Kozlowski
2022-09-16 12:12 ` [PATCH 6/6] arm64: dts: qcom: sc8180x: Introduce Lenovo Flex 5G Vinod Koul
2022-09-16 12:26 ` Dmitry Baryshkov
2022-09-16 19:11 ` Bjorn Andersson
2022-09-17 16:35 ` Krzysztof Kozlowski
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.