[PATCH V2 0/8] brcmfmac: chip related changes

[PATCH V2 0/8] brcmfmac: chip related changes

[Chi-Hsien Lin]

This patch series includes various chip-related changes:
* 43012 support
* 4373 saverestore support
* SDIO bus settings
* 4354 raw chipid

Changelog:
V2:
 - Update commit message for patch 1.
 - Update comments for patch 2.
 - Remove CY_4373_F1_MESBUSYCTRL from patch 3.
 - Collapse patch 6 (43102 sr support) in 4 (43012 support). Add helper functions.
 - Remove sr_eng_en variable from patch 8.
 - Collapse patch 10 and 11 in 9 (sdio_aos disable).

Chi-Hsien Lin (3):
  brcmfmac: add support for CYW43012 SDIO chipset
  brcmfmac: allow GCI core enumuration
  brcmfmac: 4373 save-restore support

Madhan Mohan R (1):
  brcmfmac: set SDIO F1 MesBusyCtrl for CYW4373

Naveen Gupta (1):
  brcmfmac: update 43012 F2 watermark setting to fix DMA Error during
    UDP RX Traffic

Winnie Chang (1):
  brcmfmac: add 4354 raw pcie device id

Wright Feng (2):
  brcmfmac: set F2 watermark to 256 for 4373
  brcmfmac: disable command decode in sdio_aos

 .../wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c  |   1 +
 .../wireless/broadcom/brcm80211/brcmfmac/chip.c    |  33 ++++--
 .../wireless/broadcom/brcm80211/brcmfmac/pcie.c    |   1 +
 .../wireless/broadcom/brcm80211/brcmfmac/sdio.c    | 119 ++++++++++++++++++---
 .../wireless/broadcom/brcm80211/brcmfmac/sdio.h    |   3 +
 .../broadcom/brcm80211/include/brcm_hw_ids.h       |   2 +
 include/linux/mmc/sdio_ids.h                       |   1 +
 7 files changed, 139 insertions(+), 21 deletions(-)

-- 
2.1.0

[PATCH V2 1/8] brcmfmac: add 4354 raw pcie device id

[Chi-Hsien Lin]

From: Winnie Chang <winnie.chang@cypress.com>

Add the raw 4354 PCIe device ID for unprogrammed Cypress boards.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Winnie Chang <winnie.chang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
---
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c       | 1 +
 drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h | 1 +
 2 files changed, 2 insertions(+)

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c
index 5dea569d63ed..8887bbc0084f 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c
@@ -2018,6 +2018,7 @@ static const struct dev_pm_ops brcmf_pciedrvr_pm = {
 static const struct pci_device_id brcmf_pcie_devid_table[] = {
 	BRCMF_PCIE_DEVICE(BRCM_PCIE_4350_DEVICE_ID),
 	BRCMF_PCIE_DEVICE_SUB(0x4355, BRCM_PCIE_VENDOR_ID_BROADCOM, 0x4355),
+	BRCMF_PCIE_DEVICE(BRCM_PCIE_4354_RAW_DEVICE_ID),
 	BRCMF_PCIE_DEVICE(BRCM_PCIE_4356_DEVICE_ID),
 	BRCMF_PCIE_DEVICE(BRCM_PCIE_43567_DEVICE_ID),
 	BRCMF_PCIE_DEVICE(BRCM_PCIE_43570_DEVICE_ID),
diff --git a/drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h b/drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h
index 686f7a85a045..acb87238922f 100644
--- a/drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h
+++ b/drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h
@@ -74,6 +74,7 @@
 /* PCIE Device IDs */
 #define BRCM_PCIE_4350_DEVICE_ID	0x43a3
 #define BRCM_PCIE_4354_DEVICE_ID	0x43df
+#define BRCM_PCIE_4354_RAW_DEVICE_ID	0x4354
 #define BRCM_PCIE_4356_DEVICE_ID	0x43ec
 #define BRCM_PCIE_43567_DEVICE_ID	0x43d3
 #define BRCM_PCIE_43570_DEVICE_ID	0x43d9
-- 
2.1.0

[PATCH V2 2/8] brcmfmac: set F2 watermark to 256 for 4373

[Chi-Hsien Lin]

From: Wright Feng <wright.feng@cypress.com>

We got SDIO_CRC_ERROR with 4373 on SDR104 when doing bi-directional
throughput test. Enable watermark to 256 to guarantee the operation
stability.

Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
---
 .../wireless/broadcom/brcm80211/brcmfmac/sdio.c    | 26 ++++++++++++++++++++--
 1 file changed, 24 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
index b2e1ab5adb64..05b8cfea5f9f 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
@@ -49,6 +49,10 @@
 #define DCMD_RESP_TIMEOUT	msecs_to_jiffies(2500)
 #define CTL_DONE_TIMEOUT	msecs_to_jiffies(2500)
 
+/* watermark expressed in number of words */
+#define DEFAULT_F2_WATERMARK    0x8
+#define CY_4373_F2_WATERMARK    0x40
+
 #ifdef DEBUG
 
 #define BRCMF_TRAP_INFO_SIZE	80
@@ -138,6 +142,8 @@ struct rte_console {
 /* 1: isolate internal sdio signals, put external pads in tri-state; requires
  * sdio bus power cycle to clear (rev 9) */
 #define SBSDIO_DEVCTL_PADS_ISO		0x08
+/* 1: enable F2 Watermark */
+#define SBSDIO_DEVCTL_F2WM_ENAB		0x10
 /* Force SD->SB reset mapping (rev 11) */
 #define SBSDIO_DEVCTL_SB_RST_CTL	0x30
 /*   Determined by CoreControl bit */
@@ -4046,6 +4052,7 @@ static void brcmf_sdio_firmware_callback(struct device *dev, int err,
 	void *nvram;
 	u32 nvram_len;
 	u8 saveclk;
+	u8 devctl;
 
 	brcmf_dbg(TRACE, "Enter: dev=%s, err=%d\n", dev_name(dev), err);
 
@@ -4101,8 +4108,23 @@ static void brcmf_sdio_firmware_callback(struct device *dev, int err,
 		brcmf_sdiod_writel(sdiod, core->base + SD_REG(hostintmask),
 				   bus->hostintmask, NULL);
 
-
-		brcmf_sdiod_writeb(sdiod, SBSDIO_WATERMARK, 8, &err);
+		switch (sdiod->func1->device) {
+		case SDIO_DEVICE_ID_CYPRESS_4373:
+			brcmf_dbg(INFO, "set F2 watermark to 0x%x*4 bytes\n",
+				  CY_4373_F2_WATERMARK);
+			brcmf_sdiod_writeb(sdiod, SBSDIO_WATERMARK,
+					   CY_4373_F2_WATERMARK, &err);
+			devctl = brcmf_sdiod_readb(sdiod, SBSDIO_DEVICE_CTL,
+						   &err);
+			devctl |= SBSDIO_DEVCTL_F2WM_ENAB;
+			brcmf_sdiod_writeb(sdiod, SBSDIO_DEVICE_CTL, devctl,
+					   &err);
+			break;
+		default:
+			brcmf_sdiod_writeb(sdiod, SBSDIO_WATERMARK,
+					   DEFAULT_F2_WATERMARK, &err);
+			break;
+		}
 	} else {
 		/* Disable F2 again */
 		sdio_disable_func(sdiod->func2);
-- 
2.1.0

[PATCH V2 3/8] brcmfmac: set SDIO F1 MesBusyCtrl for CYW4373

[Chi-Hsien Lin]

From: Madhan Mohan R <MadhanMohan.R@cypress.com>

Along with F2 watermark (existing) configuration, F1 MesBusyCtrl
should be enabled & configured to avoid overflow errors.

Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
---
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c | 3 +++
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h | 3 +++
 2 files changed, 6 insertions(+)

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
index 05b8cfea5f9f..b9ec40cc7d6b 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
@@ -4119,6 +4119,9 @@ static void brcmf_sdio_firmware_callback(struct device *dev, int err,
 			devctl |= SBSDIO_DEVCTL_F2WM_ENAB;
 			brcmf_sdiod_writeb(sdiod, SBSDIO_DEVICE_CTL, devctl,
 					   &err);
+			brcmf_sdiod_writeb(sdiod, SBSDIO_FUNC1_MESBUSYCTRL,
+					   CY_4373_F2_WATERMARK |
+					   SBSDIO_MESBUSYCTRL_ENAB, &err);
 			break;
 		default:
 			brcmf_sdiod_writeb(sdiod, SBSDIO_WATERMARK,
diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h
index 7faed831f07d..8aaabca1eb0e 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h
@@ -104,6 +104,9 @@
 #define SBSDIO_FUNC1_RFRAMEBCHI		0x1001C
 /* MesBusyCtl (rev 11) */
 #define SBSDIO_FUNC1_MESBUSYCTRL	0x1001D
+/* Enable busy capability for MES access */
+#define SBSDIO_MESBUSYCTRL_ENAB         0x80
+
 /* Sdio Core Rev 12 */
 #define SBSDIO_FUNC1_WAKEUPCTRL		0x1001E
 #define SBSDIO_FUNC1_WCTRL_ALPWAIT_MASK		0x1
-- 
2.1.0

[PATCH V2 4/8] brcmfmac: add support for CYW43012 SDIO chipset

[Chi-Hsien Lin]

CYW43012 is a 1x1 802.11a/b/g/n Dual-Band HT20, 256-QAM/Turbo QAM. It
is an Ultra Low Power WLAN+BT combo chip.

Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Praveen Babu C <praveen.chandran@cypress.com>
---
 .../wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c  |  1 +
 .../wireless/broadcom/brcm80211/brcmfmac/chip.c    | 14 +++-
 .../wireless/broadcom/brcm80211/brcmfmac/sdio.c    | 74 ++++++++++++++++++----
 .../broadcom/brcm80211/include/brcm_hw_ids.h       |  1 +
 include/linux/mmc/sdio_ids.h                       |  1 +
 5 files changed, 78 insertions(+), 13 deletions(-)

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
index 3e37c8cf82c6..c1d4f93f7347 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
@@ -972,6 +972,7 @@ static const struct sdio_device_id brcmf_sdmmc_ids[] = {
 	BRCMF_SDIO_DEVICE(SDIO_DEVICE_ID_BROADCOM_4354),
 	BRCMF_SDIO_DEVICE(SDIO_DEVICE_ID_BROADCOM_4356),
 	BRCMF_SDIO_DEVICE(SDIO_DEVICE_ID_CYPRESS_4373),
+	BRCMF_SDIO_DEVICE(SDIO_DEVICE_ID_CYPRESS_43012),
 	{ /* end: all zeroes */ }
 };
 MODULE_DEVICE_TABLE(sdio, brcmf_sdmmc_ids);
diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
index 927d62b3d41b..a3c857721446 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
@@ -165,6 +165,7 @@ struct sbconfig {
 #define SRCI_LSS_MASK		0x00f00000
 #define SRCI_LSS_SHIFT		20
 #define	SRCI_SRNB_MASK		0xf0
+#define	SRCI_SRNB_MASK_EXT	0x100
 #define	SRCI_SRNB_SHIFT		4
 #define	SRCI_SRBSZ_MASK		0xf
 #define	SRCI_SRBSZ_SHIFT	0
@@ -592,7 +593,13 @@ static void brcmf_chip_socram_ramsize(struct brcmf_core_priv *sr, u32 *ramsize,
 		if (lss != 0)
 			*ramsize += (1 << ((lss - 1) + SR_BSZ_BASE));
 	} else {
-		nb = (coreinfo & SRCI_SRNB_MASK) >> SRCI_SRNB_SHIFT;
+		/* length of SRAM Banks increased for corerev greater than 23 */
+		if (sr->pub.rev >= 23) {
+			nb = (coreinfo & (SRCI_SRNB_MASK | SRCI_SRNB_MASK_EXT))
+				>> SRCI_SRNB_SHIFT;
+		} else {
+			nb = (coreinfo & SRCI_SRNB_MASK) >> SRCI_SRNB_SHIFT;
+		}
 		for (i = 0; i < nb; i++) {
 			retent = brcmf_chip_socram_banksize(sr, i, &banksize);
 			*ramsize += banksize;
@@ -1356,6 +1363,11 @@ bool brcmf_chip_sr_capable(struct brcmf_chip *pub)
 		addr = CORE_CC_REG(base, sr_control1);
 		reg = chip->ops->read32(chip->ctx, addr);
 		return reg != 0;
+	case CY_CC_43012_CHIP_ID:
+		addr = CORE_CC_REG(pmu->base, retention_ctl);
+		reg = chip->ops->read32(chip->ctx, addr);
+		return (reg & (PMU_RCTL_MACPHY_DISABLE_MASK |
+			       PMU_RCTL_LOGIC_DISABLE_MASK)) == 0;
 	default:
 		addr = CORE_CC_REG(pmu->base, pmucapabilities_ext);
 		reg = chip->ops->read32(chip->ctx, addr);
diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
index b9ec40cc7d6b..7707b0169c21 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
@@ -624,6 +624,7 @@ BRCMF_FW_DEF(43455, "brcmfmac43455-sdio");
 BRCMF_FW_DEF(4354, "brcmfmac4354-sdio");
 BRCMF_FW_DEF(4356, "brcmfmac4356-sdio");
 BRCMF_FW_DEF(4373, "brcmfmac4373-sdio");
+BRCMF_FW_DEF(43012, "brcmfmac43012-sdio");
 
 static const struct brcmf_firmware_mapping brcmf_sdio_fwnames[] = {
 	BRCMF_FW_ENTRY(BRCM_CC_43143_CHIP_ID, 0xFFFFFFFF, 43143),
@@ -643,7 +644,8 @@ static const struct brcmf_firmware_mapping brcmf_sdio_fwnames[] = {
 	BRCMF_FW_ENTRY(BRCM_CC_4345_CHIP_ID, 0xFFFFFFC0, 43455),
 	BRCMF_FW_ENTRY(BRCM_CC_4354_CHIP_ID, 0xFFFFFFFF, 4354),
 	BRCMF_FW_ENTRY(BRCM_CC_4356_CHIP_ID, 0xFFFFFFFF, 4356),
-	BRCMF_FW_ENTRY(CY_CC_4373_CHIP_ID, 0xFFFFFFFF, 4373)
+	BRCMF_FW_ENTRY(CY_CC_4373_CHIP_ID, 0xFFFFFFFF, 4373),
+	BRCMF_FW_ENTRY(CY_CC_43012_CHIP_ID, 0xFFFFFFFF, 43012)
 };
 
 static void pkt_align(struct sk_buff *p, int len, int align)
@@ -677,6 +679,14 @@ brcmf_sdio_kso_control(struct brcmf_sdio *bus, bool on)
 	/* 1st KSO write goes to AOS wake up core if device is asleep  */
 	brcmf_sdiod_writeb(bus->sdiodev, SBSDIO_FUNC1_SLEEPCSR, wr_val, &err);
 
+	/* In case of 43012 chip, the chip could go down immediately after
+	 * KSO bit is cleared. So the further reads of KSO register could
+	 * fail. Thereby just bailing out immediately after clearing KSO
+	 * bit, to avoid polling of KSO bit.
+	 */
+	if (!on && bus->ci->chip == CY_CC_43012_CHIP_ID)
+		return err;
+
 	if (on) {
 		/* device WAKEUP through KSO:
 		 * write bit 0 & read back until
@@ -2402,6 +2412,14 @@ static int brcmf_sdio_tx_ctrlframe(struct brcmf_sdio *bus, u8 *frame, u16 len)
 	return ret;
 }
 
+static bool brcmf_chip_is_ulp(struct brcmf_chip *ci)
+{
+	if (ci->chip == CY_CC_43012_CHIP_ID)
+		return true;
+	else
+		return false;
+}
+
 static void brcmf_sdio_bus_stop(struct device *dev)
 {
 	struct brcmf_bus *bus_if = dev_get_drvdata(dev);
@@ -2409,7 +2427,7 @@ static void brcmf_sdio_bus_stop(struct device *dev)
 	struct brcmf_sdio *bus = sdiodev->bus;
 	struct brcmf_core *core = bus->sdio_core;
 	u32 local_hostintmask;
-	u8 saveclk;
+	u8 saveclk, bpreq;
 	int err;
 
 	brcmf_dbg(TRACE, "Enter\n");
@@ -2436,9 +2454,14 @@ static void brcmf_sdio_bus_stop(struct device *dev)
 		/* Force backplane clocks to assure F2 interrupt propagates */
 		saveclk = brcmf_sdiod_readb(sdiodev, SBSDIO_FUNC1_CHIPCLKCSR,
 					    &err);
-		if (!err)
-			brcmf_sdiod_writeb(sdiodev, SBSDIO_FUNC1_CHIPCLKCSR,
-					   (saveclk | SBSDIO_FORCE_HT), &err);
+		if (!err) {
+			bpreq = saveclk;
+			bpreq |= brcmf_chip_is_ulp(bus->ci) ?
+				SBSDIO_HT_AVAIL_REQ : SBSDIO_FORCE_HT;
+			brcmf_sdiod_writeb(sdiodev,
+					   SBSDIO_FUNC1_CHIPCLKCSR,
+					   bpreq, &err);
+		}
 		if (err)
 			brcmf_err("Failed to force clock for F2: err %d\n",
 				  err);
@@ -3328,20 +3351,45 @@ static int brcmf_sdio_download_firmware(struct brcmf_sdio *bus,
 	return bcmerror;
 }
 
+static bool brcmf_sdio_aos_no_decode(struct brcmf_sdio *bus)
+{
+	if (bus->ci->chip == CY_CC_43012_CHIP_ID)
+		return true;
+	else
+		return false;
+}
+
 static void brcmf_sdio_sr_init(struct brcmf_sdio *bus)
 {
 	int err = 0;
 	u8 val;
+	u8 wakeupctrl;
+	u8 cardcap;
+	u8 chipclkcsr;
 
 	brcmf_dbg(TRACE, "Enter\n");
 
+	if (brcmf_chip_is_ulp(bus->ci)) {
+		wakeupctrl = SBSDIO_FUNC1_WCTRL_ALPWAIT_SHIFT;
+		chipclkcsr = SBSDIO_HT_AVAIL_REQ;
+	} else {
+		wakeupctrl = SBSDIO_FUNC1_WCTRL_HTWAIT_SHIFT;
+		chipclkcsr = SBSDIO_FORCE_HT;
+	}
+
+	if (brcmf_sdio_aos_no_decode(bus)) {
+		cardcap = SDIO_CCCR_BRCM_CARDCAP_CMD_NODEC;
+	} else {
+		cardcap = (SDIO_CCCR_BRCM_CARDCAP_CMD14_SUPPORT |
+			   SDIO_CCCR_BRCM_CARDCAP_CMD14_EXT);
+	}
+
 	val = brcmf_sdiod_readb(bus->sdiodev, SBSDIO_FUNC1_WAKEUPCTRL, &err);
 	if (err) {
 		brcmf_err("error reading SBSDIO_FUNC1_WAKEUPCTRL\n");
 		return;
 	}
-
-	val |= 1 << SBSDIO_FUNC1_WCTRL_HTWAIT_SHIFT;
+	val |= 1 << wakeupctrl;
 	brcmf_sdiod_writeb(bus->sdiodev, SBSDIO_FUNC1_WAKEUPCTRL, val, &err);
 	if (err) {
 		brcmf_err("error writing SBSDIO_FUNC1_WAKEUPCTRL\n");
@@ -3350,8 +3398,7 @@ static void brcmf_sdio_sr_init(struct brcmf_sdio *bus)
 
 	/* Add CMD14 Support */
 	brcmf_sdiod_func0_wb(bus->sdiodev, SDIO_CCCR_BRCM_CARDCAP,
-			     (SDIO_CCCR_BRCM_CARDCAP_CMD14_SUPPORT |
-			      SDIO_CCCR_BRCM_CARDCAP_CMD14_EXT),
+			     cardcap,
 			     &err);
 	if (err) {
 		brcmf_err("error writing SDIO_CCCR_BRCM_CARDCAP\n");
@@ -3359,7 +3406,7 @@ static void brcmf_sdio_sr_init(struct brcmf_sdio *bus)
 	}
 
 	brcmf_sdiod_writeb(bus->sdiodev, SBSDIO_FUNC1_CHIPCLKCSR,
-			   SBSDIO_FORCE_HT, &err);
+			   chipclkcsr, &err);
 	if (err) {
 		brcmf_err("error writing SBSDIO_FUNC1_CHIPCLKCSR\n");
 		return;
@@ -4051,7 +4098,7 @@ static void brcmf_sdio_firmware_callback(struct device *dev, int err,
 	const struct firmware *code;
 	void *nvram;
 	u32 nvram_len;
-	u8 saveclk;
+	u8 saveclk, bpreq;
 	u8 devctl;
 
 	brcmf_dbg(TRACE, "Enter: dev=%s, err=%d\n", dev_name(dev), err);
@@ -4085,8 +4132,11 @@ static void brcmf_sdio_firmware_callback(struct device *dev, int err,
 	/* Force clocks on backplane to be sure F2 interrupt propagates */
 	saveclk = brcmf_sdiod_readb(sdiod, SBSDIO_FUNC1_CHIPCLKCSR, &err);
 	if (!err) {
+		bpreq = saveclk;
+		bpreq |= brcmf_chip_is_ulp(bus->ci) ?
+			SBSDIO_HT_AVAIL_REQ : SBSDIO_FORCE_HT;
 		brcmf_sdiod_writeb(sdiod, SBSDIO_FUNC1_CHIPCLKCSR,
-				   (saveclk | SBSDIO_FORCE_HT), &err);
+				   bpreq, &err);
 	}
 	if (err) {
 		brcmf_err("Failed to force clock for F2: err %d\n", err);
diff --git a/drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h b/drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h
index acb87238922f..839980da9643 100644
--- a/drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h
+++ b/drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h
@@ -60,6 +60,7 @@
 #define BRCM_CC_43664_CHIP_ID		43664
 #define BRCM_CC_4371_CHIP_ID		0x4371
 #define CY_CC_4373_CHIP_ID		0x4373
+#define CY_CC_43012_CHIP_ID		43012
 
 /* USB Device IDs */
 #define BRCM_USB_43143_DEVICE_ID	0xbd1e
diff --git a/include/linux/mmc/sdio_ids.h b/include/linux/mmc/sdio_ids.h
index 4224902a8e22..4332199c71c2 100644
--- a/include/linux/mmc/sdio_ids.h
+++ b/include/linux/mmc/sdio_ids.h
@@ -42,6 +42,7 @@
 #define SDIO_DEVICE_ID_BROADCOM_4354		0x4354
 #define SDIO_DEVICE_ID_BROADCOM_4356		0x4356
 #define SDIO_DEVICE_ID_CYPRESS_4373		0x4373
+#define SDIO_DEVICE_ID_CYPRESS_43012		43012
 
 #define SDIO_VENDOR_ID_INTEL			0x0089
 #define SDIO_DEVICE_ID_INTEL_IWMC3200WIMAX	0x1402
-- 
2.1.0

[PATCH V2 5/8] brcmfmac: allow GCI core enumuration

[Chi-Hsien Lin]

GCI core is needed for ULP operation. Allow GCI core enumuration with
below changes:
 - Allow GCI to be added to core list even when it doesn't have a wrapper.
 - Allow 8K address space size.
 - Don't overwrite the address value when an additional size descriptor
   is in place.

Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
---
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c | 14 ++++++++------
 1 file changed, 8 insertions(+), 6 deletions(-)

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
index a3c857721446..a8d3b96b727f 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
@@ -786,7 +786,7 @@ static int brcmf_chip_dmp_get_regaddr(struct brcmf_chip_priv *ci, u32 *eromaddr,
 				      u32 *regbase, u32 *wrapbase)
 {
 	u8 desc;
-	u32 val;
+	u32 val, szdesc;
 	u8 mpnum = 0;
 	u8 stype, sztype, wraptype;
 
@@ -832,14 +832,15 @@ static int brcmf_chip_dmp_get_regaddr(struct brcmf_chip_priv *ci, u32 *eromaddr,
 
 		/* next size descriptor can be skipped */
 		if (sztype == DMP_SLAVE_SIZE_DESC) {
-			val = brcmf_chip_dmp_get_desc(ci, eromaddr, NULL);
+			szdesc = brcmf_chip_dmp_get_desc(ci, eromaddr, NULL);
 			/* skip upper size descriptor if present */
-			if (val & DMP_DESC_ADDRSIZE_GT32)
+			if (szdesc & DMP_DESC_ADDRSIZE_GT32)
 				brcmf_chip_dmp_get_desc(ci, eromaddr, NULL);
 		}
 
-		/* only look for 4K register regions */
-		if (sztype != DMP_SLAVE_SIZE_4K)
+		/* look for 4K or 8K register regions */
+		if (sztype != DMP_SLAVE_SIZE_4K &&
+		    sztype != DMP_SLAVE_SIZE_8K)
 			continue;
 
 		stype = (val & DMP_SLAVE_TYPE) >> DMP_SLAVE_TYPE_S;
@@ -896,7 +897,8 @@ int brcmf_chip_dmp_erom_scan(struct brcmf_chip_priv *ci)
 
 		/* need core with ports */
 		if (nmw + nsw == 0 &&
-		    id != BCMA_CORE_PMU)
+		    id != BCMA_CORE_PMU &&
+		    id != BCMA_CORE_GCI)
 			continue;
 
 		/* try to obtain register address info */
-- 
2.1.0

[PATCH V2 6/8] brcmfmac: update 43012 F2 watermark setting to fix DMA Error during UDP RX Traffic

[Chi-Hsien Lin]

From: Naveen Gupta <naveen.gupta@cypress.com>

The number of words that the read FIFO has to contain except
the end of frame before sends data back to the host.
Max watermark = (512B - 2* (BurstLength))/4 =
(512 - 128)/4 = 384/4 = 0x60
so if burst length (i.e. BurstLength = 64) is increased,
watermark has to be reduced. This is the optimal setting for this chip.

Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Naveen Gupta <naveen.gupta@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
---
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
index 7707b0169c21..e1708e297d07 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
@@ -52,6 +52,7 @@
 /* watermark expressed in number of words */
 #define DEFAULT_F2_WATERMARK    0x8
 #define CY_4373_F2_WATERMARK    0x40
+#define CY_43012_F2_WATERMARK    0x60
 
 #ifdef DEBUG
 
@@ -4173,6 +4174,17 @@ static void brcmf_sdio_firmware_callback(struct device *dev, int err,
 					   CY_4373_F2_WATERMARK |
 					   SBSDIO_MESBUSYCTRL_ENAB, &err);
 			break;
+		case SDIO_DEVICE_ID_CYPRESS_43012:
+			brcmf_dbg(INFO, "set F2 watermark to 0x%x*4 bytes\n",
+				  CY_43012_F2_WATERMARK);
+			brcmf_sdiod_writeb(sdiod, SBSDIO_WATERMARK,
+					   CY_43012_F2_WATERMARK, &err);
+			devctl = brcmf_sdiod_readb(sdiod, SBSDIO_DEVICE_CTL,
+						   &err);
+			devctl |= SBSDIO_DEVCTL_F2WM_ENAB;
+			brcmf_sdiod_writeb(sdiod, SBSDIO_DEVICE_CTL, devctl,
+					   &err);
+			break;
 		default:
 			brcmf_sdiod_writeb(sdiod, SBSDIO_WATERMARK,
 					   DEFAULT_F2_WATERMARK, &err);
-- 
2.1.0

[PATCH V2 7/8] brcmfmac: 4373 save-restore support

[Chi-Hsien Lin]

Use sr_eng_en bit to check 4373 sr support.

Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
---
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
index a8d3b96b727f..08d5173d000c 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
@@ -1365,6 +1365,11 @@ bool brcmf_chip_sr_capable(struct brcmf_chip *pub)
 		addr = CORE_CC_REG(base, sr_control1);
 		reg = chip->ops->read32(chip->ctx, addr);
 		return reg != 0;
+	case CY_CC_4373_CHIP_ID:
+		/* explicitly check SR engine enable bit */
+		addr = CORE_CC_REG(base, sr_control0);
+		reg = chip->ops->read32(chip->ctx, addr);
+		return (reg & BIT(0)) != 0;
 	case CY_CC_43012_CHIP_ID:
 		addr = CORE_CC_REG(pmu->base, retention_ctl);
 		reg = chip->ops->read32(chip->ctx, addr);
-- 
2.1.0

[PATCH V2 8/8] brcmfmac: disable command decode in sdio_aos

[Chi-Hsien Lin]

From: Wright Feng <wright.feng@cypress.com>

AOS is a part of the SDIOD core that becomes active when the rest of
SDIOD is sleeping to keep SDIO bus alive responding to reduced set of
commands.

Transaction between AOS and SDIOD is not protected, and if cmd 52 is
received in AOS and in the middle of response state changed from AOS to
SDIOD, response is corrupted and it causes to SDIO Host controller to
hang.

Command decode for below chips are disabled in this commit:
 - 4339
 - 4345
 - 4354
 - 4373

Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
---
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
index e1708e297d07..e5f487b37c5a 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
@@ -3354,7 +3354,11 @@ static int brcmf_sdio_download_firmware(struct brcmf_sdio *bus,
 
 static bool brcmf_sdio_aos_no_decode(struct brcmf_sdio *bus)
 {
-	if (bus->ci->chip == CY_CC_43012_CHIP_ID)
+	if (bus->ci->chip == CY_CC_43012_CHIP_ID ||
+	    bus->ci->chip == CY_CC_4373_CHIP_ID ||
+	    bus->ci->chip == BRCM_CC_4339_CHIP_ID ||
+	    bus->ci->chip == BRCM_CC_4345_CHIP_ID ||
+	    bus->ci->chip == BRCM_CC_4354_CHIP_ID)
 		return true;
 	else
 		return false;
-- 
2.1.0

Re: [PATCH V2 3/8] brcmfmac: set SDIO F1 MesBusyCtrl for CYW4373

[Arend van Spriel]

On 11/12/2018 8:29 AM, Chi-Hsien Lin wrote:
> From: Madhan Mohan R <MadhanMohan.R@cypress.com>
>
> Along with F2 watermark (existing) configuration, F1 MesBusyCtrl
> should be enabled & configured to avoid overflow errors.

I am a bit confused. Why is it necessary to program the watermark in 
both SBSDIO_WATERMARK (0x10008) and SDSDIO_FUNC1_MESBUSYCTRL (0x1001D).
Looks suspicious to me.

Regards,
Arend

Re: [PATCH V2 6/8] brcmfmac: update 43012 F2 watermark setting to fix DMA Error during UDP RX Traffic

[Arend van Spriel]

On 11/12/2018 8:29 AM, Chi-Hsien Lin wrote:
> From: Naveen Gupta <naveen.gupta@cypress.com>
>
> The number of words that the read FIFO has to contain except
> the end of frame before sends data back to the host.
> Max watermark = (512B - 2* (BurstLength))/4 =
> (512 - 128)/4 = 384/4 = 0x60
> so if burst length (i.e. BurstLength = 64) is increased,
> watermark has to be reduced. This is the optimal setting for this chip.
>
> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
> Signed-off-by: Naveen Gupta <naveen.gupta@cypress.com>
> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
> ---
>  drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c | 12 ++++++++++++
>  1 file changed, 12 insertions(+)
>
> diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
> index 7707b0169c21..e1708e297d07 100644
> --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
> +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
> @@ -52,6 +52,7 @@
>  /* watermark expressed in number of words */
>  #define DEFAULT_F2_WATERMARK    0x8
>  #define CY_4373_F2_WATERMARK    0x40
> +#define CY_43012_F2_WATERMARK    0x60

So basically you increase queuing in firmware rx path. How does this 
affect TCP latency. The DMA error obviously needs fixing, but why go 
from a watermark of 32 bytes to the maximum of 384 bytes. Same question 
for 4373.

Regards,
Arend

Re: [PATCH V2 1/8] brcmfmac: add 4354 raw pcie device id

[Arend van Spriel]

On 11/12/2018 8:29 AM, Chi-Hsien Lin wrote:
> From: Winnie Chang <winnie.chang@cypress.com>
>
> Add the raw 4354 PCIe device ID for unprogrammed Cypress boards.

Already have my review tag so this is fine as is.

> Reviewed-by: Arend Van Spriel <arend@broadcom.com>
> Signed-off-by: Winnie Chang <winnie.chang@cypress.com>
> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
> ---
>  drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c       | 1 +
>  drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h | 1 +
>  2 files changed, 2 insertions(+)

Re: [PATCH V2 2/8] brcmfmac: set F2 watermark to 256 for 4373

[Arend van Spriel]

On 11/12/2018 8:29 AM, Chi-Hsien Lin wrote:
> From: Wright Feng <wright.feng@cypress.com>
>
> We got SDIO_CRC_ERROR with 4373 on SDR104 when doing bi-directional
> throughput test. Enable watermark to 256 to guarantee the operation
> stability.

Please see my comment on patch 6/8 regarding introducing queuing latency 
with this change.

Regards,
Arend

> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
> Signed-off-by: Wright Feng <wright.feng@cypress.com>
> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
> ---
>  .../wireless/broadcom/brcm80211/brcmfmac/sdio.c    | 26 ++++++++++++++++++++--
>  1 file changed, 24 insertions(+), 2 deletions(-)

Re: [PATCH V2 5/8] brcmfmac: allow GCI core enumuration

[Arend van Spriel]

On 11/12/2018 8:29 AM, Chi-Hsien Lin wrote:
> GCI core is needed for ULP operation. Allow GCI core enumuration with
> below changes:
>  - Allow GCI to be added to core list even when it doesn't have a wrapper.
>  - Allow 8K address space size.
>  - Don't overwrite the address value when an additional size descriptor
>    is in place.

One question. This only assures the GCI core is listed. So does the 
driver need to access it for ULP operation?

Regards,
Arend

> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
> ---
>  drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c | 14 ++++++++------
>  1 file changed, 8 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
> index a3c857721446..a8d3b96b727f 100644
> --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
> +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
> @@ -786,7 +786,7 @@ static int brcmf_chip_dmp_get_regaddr(struct brcmf_chip_priv *ci, u32 *eromaddr,
>  				      u32 *regbase, u32 *wrapbase)
>  {
>  	u8 desc;
> -	u32 val;
> +	u32 val, szdesc;
>  	u8 mpnum = 0;
>  	u8 stype, sztype, wraptype;
>
> @@ -832,14 +832,15 @@ static int brcmf_chip_dmp_get_regaddr(struct brcmf_chip_priv *ci, u32 *eromaddr,
>
>  		/* next size descriptor can be skipped */
>  		if (sztype == DMP_SLAVE_SIZE_DESC) {
> -			val = brcmf_chip_dmp_get_desc(ci, eromaddr, NULL);
> +			szdesc = brcmf_chip_dmp_get_desc(ci, eromaddr, NULL);
>  			/* skip upper size descriptor if present */
> -			if (val & DMP_DESC_ADDRSIZE_GT32)
> +			if (szdesc & DMP_DESC_ADDRSIZE_GT32)
>  				brcmf_chip_dmp_get_desc(ci, eromaddr, NULL);
>  		}
>
> -		/* only look for 4K register regions */
> -		if (sztype != DMP_SLAVE_SIZE_4K)
> +		/* look for 4K or 8K register regions */
> +		if (sztype != DMP_SLAVE_SIZE_4K &&
> +		    sztype != DMP_SLAVE_SIZE_8K)
>  			continue;
>
>  		stype = (val & DMP_SLAVE_TYPE) >> DMP_SLAVE_TYPE_S;
> @@ -896,7 +897,8 @@ int brcmf_chip_dmp_erom_scan(struct brcmf_chip_priv *ci)
>
>  		/* need core with ports */
>  		if (nmw + nsw == 0 &&
> -		    id != BCMA_CORE_PMU)
> +		    id != BCMA_CORE_PMU &&
> +		    id != BCMA_CORE_GCI)
>  			continue;
>
>  		/* try to obtain register address info */
>

Re: [PATCH V2 5/8] brcmfmac: allow GCI core enumuration

[Chi-Hsien Lin]

On 11/12/2018 6:16, Arend van Spriel wrote:
> On 11/12/2018 8:29 AM, Chi-Hsien Lin wrote:
>> GCI core is needed for ULP operation. Allow GCI core enumuration with
>> below changes:
>>  - Allow GCI to be added to core list even when it doesn't have a 
>> wrapper.
>>  - Allow 8K address space size.
>>  - Don't overwrite the address value when an additional size descriptor
>>    is in place.
> 
> One question. This only assures the GCI core is listed. So does the
> driver need to access it for ULP operation?

Yes, the GCI core registers are accessed when entering/exiting ULP sleep 
modes. There will be other patches for the ULP support.

Regards,
Chi-hsien Lin

> 
> Regards,
> Arend
> 
>> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
>> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
>> ---
>>  drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c | 14 
>> ++++++++------
>>  1 file changed, 8 insertions(+), 6 deletions(-)
>>
>> diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c 
>> b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
>> index a3c857721446..a8d3b96b727f 100644
>> --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
>> +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
>> @@ -786,7 +786,7 @@ static int brcmf_chip_dmp_get_regaddr(struct 
>> brcmf_chip_priv *ci, u32 *eromaddr,
>>                                     u32 *regbase, u32 *wrapbase)
>>  {
>>       u8 desc;
>> -     u32 val;
>> +     u32 val, szdesc;
>>       u8 mpnum = 0;
>>       u8 stype, sztype, wraptype;
>>
>> @@ -832,14 +832,15 @@ static int brcmf_chip_dmp_get_regaddr(struct 
>> brcmf_chip_priv *ci, u32 *eromaddr,
>>
>>               /* next size descriptor can be skipped */
>>               if (sztype == DMP_SLAVE_SIZE_DESC) {
>> -                     val = brcmf_chip_dmp_get_desc(ci, eromaddr, NULL);
>> +                     szdesc = brcmf_chip_dmp_get_desc(ci, eromaddr, 
>> NULL);
>>                       /* skip upper size descriptor if present */
>> -                     if (val & DMP_DESC_ADDRSIZE_GT32)
>> +                     if (szdesc & DMP_DESC_ADDRSIZE_GT32)
>>                               brcmf_chip_dmp_get_desc(ci, eromaddr, 
>> NULL);
>>               }
>>
>> -             /* only look for 4K register regions */
>> -             if (sztype != DMP_SLAVE_SIZE_4K)
>> +             /* look for 4K or 8K register regions */
>> +             if (sztype != DMP_SLAVE_SIZE_4K &&
>> +                 sztype != DMP_SLAVE_SIZE_8K)
>>                       continue;
>>
>>               stype = (val & DMP_SLAVE_TYPE) >> DMP_SLAVE_TYPE_S;
>> @@ -896,7 +897,8 @@ int brcmf_chip_dmp_erom_scan(struct 
>> brcmf_chip_priv *ci)
>>
>>               /* need core with ports */
>>               if (nmw + nsw == 0 &&
>> -                 id != BCMA_CORE_PMU)
>> +                 id != BCMA_CORE_PMU &&
>> +                 id != BCMA_CORE_GCI)
>>                       continue;
>>
>>               /* try to obtain register address info */
>>
> 
> 
> 
> ----------
> 
> You're receiving this message because you're a member of the 
> brcm80211-dev-list group.
> .
> 

Re: [PATCH V2 5/8] brcmfmac: allow GCI core enumuration

[Arend van Spriel]

On 11/12/2018 11:24 AM, Chi-Hsien Lin wrote:
>
>
> On 11/12/2018 6:16, Arend van Spriel wrote:
>> On 11/12/2018 8:29 AM, Chi-Hsien Lin wrote:
>>> GCI core is needed for ULP operation. Allow GCI core enumuration with
>>> below changes:
>>>  - Allow GCI to be added to core list even when it doesn't have a
>>> wrapper.
>>>  - Allow 8K address space size.
>>>  - Don't overwrite the address value when an additional size descriptor
>>>    is in place.
>>
>> One question. This only assures the GCI core is listed. So does the
>> driver need to access it for ULP operation?
>
> Yes, the GCI core registers are accessed when entering/exiting ULP sleep
> modes. There will be other patches for the ULP support.

Yeah. I suspected such. It would have been better to send this patch 
with that ULP series, but let's not make it an issue now. The patch is fine.

Regards,
Arend

Re: [PATCH V2 5/8] brcmfmac: allow GCI core enumuration

[Chi-Hsien Lin]

On 11/12/2018 6:27, Arend van Spriel wrote:
> On 11/12/2018 11:24 AM, Chi-Hsien Lin wrote:
>>
>>
>> On 11/12/2018 6:16, Arend van Spriel wrote:
>>> On 11/12/2018 8:29 AM, Chi-Hsien Lin wrote:
>>>> GCI core is needed for ULP operation. Allow GCI core enumuration with
>>>> below changes:
>>>>  - Allow GCI to be added to core list even when it doesn't have a
>>>> wrapper.
>>>>  - Allow 8K address space size.
>>>>  - Don't overwrite the address value when an additional size descriptor
>>>>    is in place.
>>>
>>> One question. This only assures the GCI core is listed. So does the
>>> driver need to access it for ULP operation?
>>
>> Yes, the GCI core registers are accessed when entering/exiting ULP sleep
>> modes. There will be other patches for the ULP support.
> 
> Yeah. I suspected such. It would have been better to send this patch 
> with that ULP series, but let's not make it an issue now. The patch is 
> fine.

Thanks a lot.  :)

> 
> Regards,
> Arend
> 
> .
> 

Re: [PATCH V2 7/8] brcmfmac: 4373 save-restore support

[Arend van Spriel]

On 11/12/2018 8:29 AM, Chi-Hsien Lin wrote:
> Use sr_eng_en bit to check 4373 sr support.
>
> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
> ---
>  drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c | 5 +++++
>  1 file changed, 5 insertions(+)
>
> diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
> index a8d3b96b727f..08d5173d000c 100644
> --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
> +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
> @@ -1365,6 +1365,11 @@ bool brcmf_chip_sr_capable(struct brcmf_chip *pub)
>  		addr = CORE_CC_REG(base, sr_control1);
>  		reg = chip->ops->read32(chip->ctx, addr);
>  		return reg != 0;
> +	case CY_CC_4373_CHIP_ID:
> +		/* explicitly check SR engine enable bit */
> +		addr = CORE_CC_REG(base, sr_control0);
> +		reg = chip->ops->read32(chip->ctx, addr);
> +		return (reg & BIT(0)) != 0;

Sorry for not saying it earlier, but maybe it is good to add define of 
SR engine enable bit in brcm80211/include/chipcommon.h.

Regards,
Arend

Re: [PATCH V2 8/8] brcmfmac: disable command decode in sdio_aos

[Arend van Spriel]

On 11/12/2018 8:30 AM, Chi-Hsien Lin wrote:
> From: Wright Feng <wright.feng@cypress.com>
>
> AOS is a part of the SDIOD core that becomes active when the rest of
> SDIOD is sleeping to keep SDIO bus alive responding to reduced set of
> commands.
>
> Transaction between AOS and SDIOD is not protected, and if cmd 52 is
> received in AOS and in the middle of response state changed from AOS to
> SDIOD, response is corrupted and it causes to SDIO Host controller to
> hang.
>
> Command decode for below chips are disabled in this commit:
>  - 4339
>  - 4345
>  - 4354
>  - 4373

Already have my review tag so this is fine as is.

> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
> Signed-off-by: Wright Feng <wright.feng@cypress.com>
> Signed-off-by: Double Lo <double.lo@cypress.com>
> Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
> ---
>  drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c | 6 +++++-
>  1 file changed, 5 insertions(+), 1 deletion(-)

Re: [PATCH V2 8/8] brcmfmac: disable command decode in sdio_aos

[Arend van Spriel]

On 11/12/2018 8:30 AM, Chi-Hsien Lin wrote:
> From: Wright Feng <wright.feng@cypress.com>
>
> AOS is a part of the SDIOD core that becomes active when the rest of
> SDIOD is sleeping to keep SDIO bus alive responding to reduced set of
> commands.
>
> Transaction between AOS and SDIOD is not protected, and if cmd 52 is
> received in AOS and in the middle of response state changed from AOS to
> SDIOD, response is corrupted and it causes to SDIO Host controller to
> hang.

Just one question. The above sound pretty generic so does it apply to 
any SDIO chip with AOS logic?

Regards,
Arend

Re: [PATCH V2 8/8] brcmfmac: disable command decode in sdio_aos

[Wright Feng]

On 2018/11/12 下午 06:33, Arend van Spriel wrote:
> On 11/12/2018 8:30 AM, Chi-Hsien Lin wrote:
>> From: Wright Feng <wright.feng@cypress.com>
>>
>> AOS is a part of the SDIOD core that becomes active when the rest of
>> SDIOD is sleeping to keep SDIO bus alive responding to reduced set of
>> commands.
>>
>> Transaction between AOS and SDIOD is not protected, and if cmd 52 is
>> received in AOS and in the middle of response state changed from AOS to
>> SDIOD, response is corrupted and it causes to SDIO Host controller to
>> hang.
> 
> Just one question. The above sound pretty generic so does it apply to
> any SDIO chip with AOS logic?
> 
We found this issue when verifying SR feature with some SDIO cards(what
we had), not sure whether every SDIO card has same problem. So we
only change those chip's wake-up mechanism to noCmdDecode mode and let
SDIOD_AOS just generates a wake-up request without responding.

-Wright
> Regards,
> Arend
> 
> 
> 

Re: [PATCH V2 3/8] brcmfmac: set SDIO F1 MesBusyCtrl for CYW4373

[Madhan Mohan R]

On Mon, Nov 12, 2018 at 10:13:07AM +0100, Arend van Spriel wrote:
> On 11/12/2018 8:29 AM, Chi-Hsien Lin wrote:
> >From: Madhan Mohan R <MadhanMohan.R@cypress.com>
> >
> >Along with F2 watermark (existing) configuration, F1 MesBusyCtrl
> >should be enabled & configured to avoid overflow errors.
> 
> I am a bit confused. Why is it necessary to program the watermark in
> both SBSDIO_WATERMARK (0x10008) and SDSDIO_FUNC1_MESBUSYCTRL
> (0x1001D).
> Looks suspicious to me.
> 
> Regards,
> Arend

Hi Arend,

Register SDSDIO_FUNC1_MESBUSYCTRL(0x1001D) Bits [6:0] is programmed with
SDIO RX path watermark whereas the register SBSDIO_WATERMARK(0x10008) is
for the SDIO TX path.

Regards,
Madhan

Re: [PATCH V2 6/8] brcmfmac: update 43012 F2 watermark setting to fix DMA Error during UDP RX Traffic

[Chi-Hsien Lin]

(+Madhan)

On 11/12/2018 5:25, Arend van Spriel wrote:
> On 11/12/2018 8:29 AM, Chi-Hsien Lin wrote:
>> From: Naveen Gupta <naveen.gupta@cypress.com>
>>
>> The number of words that the read FIFO has to contain except
>> the end of frame before sends data back to the host.
>> Max watermark = (512B - 2* (BurstLength))/4 =
>> (512 - 128)/4 = 384/4 = 0x60
>> so if burst length (i.e. BurstLength = 64) is increased,
>> watermark has to be reduced. This is the optimal setting for this chip.
>>
>> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
>> Signed-off-by: Naveen Gupta <naveen.gupta@cypress.com>
>> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
>> ---
>>  drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c | 12 
>> ++++++++++++
>>  1 file changed, 12 insertions(+)
>>
>> diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c 
>> b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
>> index 7707b0169c21..e1708e297d07 100644
>> --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
>> +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
>> @@ -52,6 +52,7 @@
>>  /* watermark expressed in number of words */
>>  #define DEFAULT_F2_WATERMARK    0x8
>>  #define CY_4373_F2_WATERMARK    0x40
>> +#define CY_43012_F2_WATERMARK    0x60
> 
> So basically you increase queuing in firmware rx path. How does this
> affect TCP latency. The DMA error obviously needs fixing, but why go
> from a watermark of 32 bytes to the maximum of 384 bytes. Same question
> for 4373.

This is to answer 2/8 and 6/8 -

For current chips like 4373 and 43012, we are configuring F2 block size 
as 256 and it is recommended to program the F2 watermark (SDIO TX path - 
SDIO Device to host traffic) to at least equal or greater than the block 
size to make sure that at least >= 1 Block size of data is in FIFO 
before sending on the SDIO bus to avoid underflow. We haven't observed 
excess TCP latency with this setting.

Regards,
Chi-hsien Lin

> 
> Regards,
> Arend

Re: [PATCH V2 7/8] brcmfmac: 4373 save-restore support

[Chi-Hsien Lin]

On 11/12/2018 6:30, Arend van Spriel wrote:
> On 11/12/2018 8:29 AM, Chi-Hsien Lin wrote:
>> Use sr_eng_en bit to check 4373 sr support.
>>
>> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
>> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
>> ---
>>  drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c | 5 +++++
>>  1 file changed, 5 insertions(+)
>>
>> diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c 
>> b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
>> index a8d3b96b727f..08d5173d000c 100644
>> --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
>> +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c
>> @@ -1365,6 +1365,11 @@ bool brcmf_chip_sr_capable(struct brcmf_chip *pub)
>>          addr = CORE_CC_REG(base, sr_control1);
>>          reg = chip->ops->read32(chip->ctx, addr);
>>          return reg != 0;
>> +    case CY_CC_4373_CHIP_ID:
>> +        /* explicitly check SR engine enable bit */
>> +        addr = CORE_CC_REG(base, sr_control0);
>> +        reg = chip->ops->read32(chip->ctx, addr);
>> +        return (reg & BIT(0)) != 0;
> 
> Sorry for not saying it earlier, but maybe it is good to add define of 
> SR engine enable bit in brcm80211/include/chipcommon.h.

No problem. I'll make this change and submit V3 shortly.

> 
> Regards,
> Arend
> .
> 

Re: [PATCH V2 3/8] brcmfmac: set SDIO F1 MesBusyCtrl for CYW4373

[Arend van Spriel]

On 11/20/2018 9:50 AM, Madhan Mohan R wrote:
> On Mon, Nov 12, 2018 at 10:13:07AM +0100, Arend van Spriel wrote:
>> On 11/12/2018 8:29 AM, Chi-Hsien Lin wrote:
>>> From: Madhan Mohan R <MadhanMohan.R@cypress.com>
>>>
>>> Along with F2 watermark (existing) configuration, F1 MesBusyCtrl
>>> should be enabled & configured to avoid overflow errors.
>>
>> I am a bit confused. Why is it necessary to program the watermark in
>> both SBSDIO_WATERMARK (0x10008) and SDSDIO_FUNC1_MESBUSYCTRL
>> (0x1001D).
>> Looks suspicious to me.
>>
>> Regards,
>> Arend
>
> Hi Arend,
>
> Register SDSDIO_FUNC1_MESBUSYCTRL(0x1001D) Bits [6:0] is programmed with
> SDIO RX path watermark whereas the register SBSDIO_WATERMARK(0x10008) is
> for the SDIO TX path.

Thanks, Madhan

That makes sense. Maybe it would be good to express the tx vs rx detail 
in the code.

Regards,
Arend