* rtl8192ce: activation problem with rtl8188ce pci card
@ 2012-09-05 16:55 Anisse Astier
2012-09-05 17:38 ` Larry Finger
0 siblings, 1 reply; 10+ messages in thread
From: Anisse Astier @ 2012-09-05 16:55 UTC (permalink / raw)
To: linux-wireless; +Cc: Larry Finger
[-- Attachment #1: Type: text/plain, Size: 4637 bytes --]
Hi,
On a toshiba laptop (see dmesg attached), with a wireless-next kernel,
this card doesn't seem to turn on:
01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02)
# modprobe rtl8192ce debug=4
[ 6184.995319] cfg80211: Calling CRDA to update world regulatory domain
[ 6185.103824] rtl8192ce: rtl8192ce: FW Power Save off (module option)
[ 6185.103881] rtl8192ce: Using firmware rtlwifi/rtl8192cfw.bin
[ 6185.150488] rtlwifi:rtl_fw_cb():<0-0> Firmware callback routine entered!
[ 6185.216834] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 6185.224729] rtlwifi: wireless switch is on
[ 6185.289544] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 6185.289649] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 6185.289797] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 6185.289944] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 6185.290092] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 6185.290250] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 6185.290398] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 6185.290545] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 6185.290693] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:98053f15:10
[ 6185.291829] rtl8192c_common:rtl92c_download_fw():<0-0> Firmware Version(49), Signature(0x88c1),Size(32)
[ 6185.513223] rtl8192ce:rtl92ce_enable_hw_security_config():<0-0> PairwiseEncAlgorithm = 0 GroupEncAlgorithm = 0
[ 6185.513237] rtl8192ce:rtl92ce_enable_hw_security_config():<0-0> The SECR-value cc
[ 6185.622274] rtl8192c_common:rtl92c_dm_initialize_txpower_tracking_thermalmeter():<0-0> pMgntInfo->txpower_tracking = 1
[ 6185.623129] rtlwifi:rtl_pci_start():<0-0> enable_interrupt OK
[ 6185.623140] rtlwifi:rtl_pci_start():<0-0> OK
[ 6185.624061] rtl8192c_common:rtl92c_dm_dynamic_bb_powersaving():<0-0> Not connected to any
[ 6185.624073] rtl8192c_common:rtl92c_dm_dynamic_bb_powersaving():<0-0> AP Ext Port PWDB = 0x0
[ 6185.624123] rtl8192c_common:rtl92c_dm_check_txpower_tracking_thermal_meter():<0-0> Trigger 92S Thermal Meter!!
[ 6185.632970] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
[ 6185.632987] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
[ 6185.633028] rtlwifi:rtl_op_bss_info_changed():<0-0> BSS_CHANGED_ERP_PREAMBLE use short preamble:0
[ 6185.633040] rtl8192ce:rtl92ce_set_hw_reg():<0-0> HW_VAR_SLOT_TIME 14
[ 6185.633989] rtlwifi:rtl_op_config():<0-0> IEEE80211_CONF_CHANGE_LISTEN_INTERVAL
[ 6185.634281] rtlwifi:rtl_op_config():<0-0> IEEE80211_CONF_CHANGE_RETRY_LIMITS 4
[ 6185.644434] rtl8192c_common:rtl92c_phy_sw_chnl():<0-0> sw_chnl_inprogress false schdule workitem
[ 6185.644445] rtl8192ce:rtl92ce_set_hw_reg():<0-0> HW_VAR_SLOT_TIME 14
[ 6185.655245] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6185.734598] rtl8192ce:_rtl92ce_phy_set_rf_power_state():<0-0> IPS Set eRf nic disable
[ 6185.735117] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
[ 6185.735129] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
[ 6185.852489] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 6185.852504] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
[ 6185.853211] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 6185.853221] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
[ 6185.853823] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 6185.853833] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
[...] this is repeated
After a modprobe -r:
[ 6187.127706] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
[ 6187.127724] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
[ 6187.130614] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
[ 6187.130626] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
[ 6187.130638] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 7
[ 6187.130646] rtl8192ce:rtl92ce_sw_led_off():<0-0> LedAddr:4E ledpin=1
[ 6187.139353] rtl8192c_common:rtl92c_firmware_selfreset(): 8051 reset fail
[ 6187.139373] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 7
[ 6187.139382] rtl8192ce:rtl92ce_sw_led_off():<0-0> LedAddr:4E ledpin=1
After inserting the module, the PCI information is scrambled:
06:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8176 (rev ff) (prog-if ff)
!!! Unknown header type 7f
After a few seconds, the computer will freeze if the module isn't removed.
The card works on Windows.
This looks like a hidden rfkill, or maybe it is a different revision of
the card. What do you think ?
Regards,
Anisse
[-- Attachment #2: dmesg-rtl8192ce-no-up.txt --]
[-- Type: text/plain, Size: 52836 bytes --]
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.5.0 (root@compilator-1) (gcc version 4.4.5 (Debian 4.4.5-8) ) #13 SMP Wed Sep 5 15:51:44 CEST 2012
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000df6befff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000df6bf000-0x00000000dfabefff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000dfabf000-0x00000000dfbbefff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000dfbbf000-0x00000000dfbfefff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000dfbff000-0x00000000dfbfffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000dfc00000-0x00000000dfffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed80fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffe00000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000106ffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000107000000-0x000000011effffff] reserved
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.7 present.
[ 0.000000] DMI: TOSHIBA SATELLITE C850D-115/Renmore, BIOS 1.10 04/25/2012
[ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x107000 max_arch_pfn = 0x1000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-through
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 080000000 mask FC0000000 write-back
[ 0.000000] 2 base 0C0000000 mask FE0000000 write-back
[ 0.000000] 3 base 0DFBBC000 mask FFFFFF000 uncachable
[ 0.000000] 4 base 0FFE00000 mask FFFE00000 write-protect
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 000000011f000000 aka 4592M
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped: [mem 0x00000000-0x01ffffff]
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x37bfdfff]
[ 0.000000] [mem 0x00000000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x379fffff] page 2M
[ 0.000000] [mem 0x37a00000-0x37bfdfff] page 4k
[ 0.000000] kernel direct mapping tables up to 0x37bfdfff @ [mem 0x01ffa000-0x01ffffff]
[ 0.000000] RAMDISK: [mem 0x037bd000-0x03ffffff]
[ 0.000000] ACPI: RSDP 000fe020 00024 (v02 TOSASU)
[ 0.000000] ACPI: XSDT dfbfe120 00084 (v01 TOSASU TOSASU00 00000001 01000013)
[ 0.000000] ACPI: FACP dfbfc000 0010C (v05 TOSASU TOSASU00 00000001 ACPI 00040000)
[ 0.000000] ACPI: DSDT dfbdd000 1A3D2 (v01 TOSASU TOSASU00 F0000000 ACPI 00040000)
[ 0.000000] ACPI: FACS dfb82000 00040
[ 0.000000] ACPI: UEFI dfbfd000 00236 (v01 TOSASU TOSASU00 00000001 ACPI 00040000)
[ 0.000000] ACPI: HPET dfbfb000 00038 (v01 TOSASU TOSASU00 00000001 ACPI 00040000)
[ 0.000000] ACPI: APIC dfbfa000 00084 (v03 TOSASU TOSASU00 00000001 ACPI 00040000)
[ 0.000000] ACPI: MCFG dfbf9000 0003C (v01 TOSASU TOSASU00 00000001 ACPI 00040000)
[ 0.000000] ACPI: ASF! dfbf8000 000A5 (v32 TOSASU TOSASU00 00000001 ACPI 00040000)
[ 0.000000] ACPI: BOOT dfbdc000 00028 (v01 TOSASU TOSASU00 00000001 ACPI 00040000)
[ 0.000000] ACPI: SLIC dfbdb000 00176 (v01 TOSASU TOSASU00 00000001 ACPI 00040000)
[ 0.000000] ACPI: WDRT dfbda000 00047 (v01 TOSASU TOSASU00 00000000 ACPI 00040000)
[ 0.000000] ACPI: WDAT dfbd9000 001AC (v01 TOSASU TOSASU00 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT dfbd8000 003DE (v01 AMD POWERNOW 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT dfbd6000 016CF (v02 AMD ALIB 00000001 MSFT 04000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 3316MB HIGHMEM available.
[ 0.000000] 891MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 37bfe000
[ 0.000000] low ram: 0 - 37bfe000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00010000-0x00ffffff]
[ 0.000000] Normal [mem 0x01000000-0x37bfdfff]
[ 0.000000] HighMem [mem 0x37bfe000-0x06ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00010000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0xdf6befff]
[ 0.000000] node 0: [mem 0xdfbff000-0xdfbfffff]
[ 0.000000] node 0: [mem 0x00000000-0x06ffffff]
[ 0.000000] On node 0 totalpages: 943695
[ 0.000000] free_area_init_node: node 0, pgdat c1591e80, node_mem_map f5b1d200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1752 pages used for memmap
[ 0.000000] Normal zone: 222502 pages, LIFO batch:31
[ 0.000000] HighMem zone: 6633 pages used for memmap
[ 0.000000] HighMem zone: 708825 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10228210 base: 0xfed00000
[ 0.000000] smpboot: Allowing 4 CPUs, 3 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] e820: [mem 0xe0000000-0xf7ffffff] available for PCI devices
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 13 pages/cpu @f5ab4000 s32064 r0 d21184 u53248
[ 0.000000] pcpu-alloc: s32064 r0 d21184 u53248 alloc=13*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 935278
[ 0.000000] Kernel command line: auto BOOT_IMAGE=Ordissimo ro root=LABEL=root splash=silent quiet radeon.modeset=1 i915.modeset=1
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (00037bfe:00107000)
[ 0.000000] Memory: 3719696k/4308992k available (3651k kernel code, 55084k reserved, 2091k data, 484k init, 2861832k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
[ 0.000000] pkmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xf83fe000 - 0xffbfe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf7bfe000 ( 891 MB)
[ 0.000000] .init : 0xc159c000 - 0xc1615000 ( 484 kB)
[ 0.000000] .data : 0xc1390de8 - 0xc159bdc0 (2091 kB)
[ 0.000000] .text : 0xc1000000 - 0xc1390de8 (3651 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] NR_IRQS:2304 nr_irqs:712 16
[ 0.000000] CPU 0 irqstacks, hard=f5408000 soft=f540a000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000000] ... MAX_LOCK_DEPTH: 48
[ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000000] ... CLASSHASH_SIZE: 4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.000000] ... CHAINHASH_SIZE: 16384
[ 0.000000] memory used by lock dependency info: 3567 kB
[ 0.000000] per task-struct memory footprint: 1152 bytes
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.001000] tsc: Detected 1397.338 MHz processor
[ 0.000005] Calibrating delay loop (skipped), value calculated using timer frequency.. 2794.67 BogoMIPS (lpj=1397338)
[ 0.000013] pid_max: default: 32768 minimum: 301
[ 0.000179] Mount-cache hash table entries: 512
[ 0.002308] CPU: Physical Processor ID: 0
[ 0.002314] CPU: Processor Core ID: 0
[ 0.002319] mce: CPU supports 6 MCE banks
[ 0.002346] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.002346] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.002346] tlb_flushall_shift is 0xffffffff
[ 0.002849] SMP alternatives: lockdep: fixing up alternatives
[ 0.002854] SMP alternatives: switching to UP code
[ 0.009206] ACPI: Core revision 20120711
[ 0.049352] ftrace: allocating 16506 entries in 33 pages
[ 0.066164] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.066831] ..TIMER: vector=0x51 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.076834] smpboot: CPU0: AMD E1-1200 APU with Radeon(tm) HD Graphics stepping 00
[ 0.178280] Performance Events: AMD PMU driver.
[ 0.178300] ... version: 0
[ 0.178304] ... bit width: 48
[ 0.178308] ... generic registers: 4
[ 0.178312] ... value mask: 0000ffffffffffff
[ 0.178315] ... max period: 00007fffffffffff
[ 0.178318] ... fixed-purpose events: 0
[ 0.178322] ... event mask: 000000000000000f
[ 0.179652] Brought up 1 CPUs
[ 0.179661] smpboot: Total of 1 processors activated (2794.67 BogoMIPS)
[ 0.181456] devtmpfs: initialized
[ 0.182456] PM: Registering ACPI NVS region [mem 0xdfabf000-0xdfbbefff] (1048576 bytes)
[ 0.184969] NET: Registered protocol family 16
[ 0.188126] ACPI: bus type pci registered
[ 0.188757] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.188766] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.188769] PCI: Using MMCONFIG for extended config space
[ 0.188774] PCI: Using configuration type 1 for base access
[ 0.207097] bio: create slab <bio-0> at 0
[ 0.207684] ACPI: Added _OSI(Module Device)
[ 0.207697] ACPI: Added _OSI(Processor Device)
[ 0.207702] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.207707] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.230869] ACPI: EC: Look up EC in DSDT
[ 2.782403] ACPI: Executed 1 blocks of module-level executable AML code
[ 2.799424] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 2.803556] ACPI: Interpreter enabled
[ 2.803568] ACPI: (supports S0 S3 S5)
[ 2.803678] ACPI: Using IOAPIC for interrupt routing
[ 2.807268] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 2.808513] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 2.846353] ACPI: Power Resource [P0L0] (off)
[ 2.846798] ACPI: Power Resource [P0L1] (off)
[ 2.847099] ACPI: Power Resource [P0L2] (off)
[ 2.847451] ACPI: Power Resource [P0L3] (off)
[ 2.853505] ACPI: EC: GPE = 0xc, I/O: command/status = 0x66, data = 0x62
[ 2.854948] ACPI: No dock devices found.
[ 2.854960] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 2.855985] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 2.856522] pci_root PNP0A08:00: ignoring host bridge window [mem 0x000cc000-0x000cffff] (conflicts with Video ROM [mem 0x000c0000-0x000cefff])
[ 2.856565] pci_root PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[ 2.857101] PCI host bridge to bus 0000:00
[ 2.857112] pci_bus 0000:00: busn_res: [bus 00-ff] is inserted under domain [bus 00-ff]
[ 2.857118] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.857125] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 2.857131] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 2.857136] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 2.857142] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000c3fff]
[ 2.857148] pci_bus 0000:00: root bus resource [mem 0x000c4000-0x000c7fff]
[ 2.857155] pci_bus 0000:00: root bus resource [mem 0x000c8000-0x000cbfff]
[ 2.857160] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff]
[ 2.857166] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
[ 2.857173] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
[ 2.857178] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
[ 2.857183] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff]
[ 2.857188] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff]
[ 2.857194] pci_bus 0000:00: root bus resource [mem 0x000e8000-0x000ebfff]
[ 2.857200] pci_bus 0000:00: root bus resource [mem 0x000ec000-0x000effff]
[ 2.857205] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xf7ffffff]
[ 2.857211] pci_bus 0000:00: root bus resource [mem 0xfc000000-0xfed3ffff]
[ 2.857217] pci_bus 0000:00: root bus resource [mem 0xfed45000-0xffffffff]
[ 2.857350] pci 0000:00:00.0: [1022:1510] type 00 class 0x060000
[ 2.857529] pci 0000:00:01.0: [1002:9809] type 00 class 0x030000
[ 2.857555] pci 0000:00:01.0: reg 10: [mem 0xe0000000-0xefffffff pref]
[ 2.857574] pci 0000:00:01.0: reg 14: [io 0x5000-0x50ff]
[ 2.857593] pci 0000:00:01.0: reg 18: [mem 0xf0400000-0xf043ffff]
[ 2.857720] pci 0000:00:01.0: supports D1 D2
[ 2.857763] pci 0000:00:01.1: [1002:1314] type 00 class 0x040300
[ 2.857787] pci 0000:00:01.1: reg 10: [mem 0xf0444000-0xf0447fff]
[ 2.857935] pci 0000:00:01.1: supports D1 D2
[ 2.858095] pci 0000:00:11.0: [1022:7800] type 00 class 0x01018f
[ 2.858128] pci 0000:00:11.0: reg 10: [io 0x5118-0x511f]
[ 2.858149] pci 0000:00:11.0: reg 14: [io 0x5124-0x5127]
[ 2.858170] pci 0000:00:11.0: reg 18: [io 0x5110-0x5117]
[ 2.858191] pci 0000:00:11.0: reg 1c: [io 0x5120-0x5123]
[ 2.858212] pci 0000:00:11.0: reg 20: [io 0x5100-0x510f]
[ 2.858243] pci 0000:00:11.0: reg 24: [mem 0xf044f000-0xf044f7ff]
[ 2.858291] pci 0000:00:11.0: set SATA to AHCI mode
[ 2.858367] pci 0000:00:12.0: [1022:7807] type 00 class 0x0c0310
[ 2.858394] pci 0000:00:12.0: reg 10: [mem 0xf044e000-0xf044efff]
[ 2.858544] pci 0000:00:12.2: [1022:7808] type 00 class 0x0c0320
[ 2.858582] pci 0000:00:12.2: reg 10: [mem 0xf044d000-0xf044d0ff]
[ 2.858751] pci 0000:00:12.2: supports D1 D2
[ 2.858757] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
[ 2.858933] pci 0000:00:13.0: [1022:7807] type 00 class 0x0c0310
[ 2.858960] pci 0000:00:13.0: reg 10: [mem 0xf044c000-0xf044cfff]
[ 2.859112] pci 0000:00:13.2: [1022:7808] type 00 class 0x0c0320
[ 2.859150] pci 0000:00:13.2: reg 10: [mem 0xf044b000-0xf044b0ff]
[ 2.859330] pci 0000:00:13.2: supports D1 D2
[ 2.859336] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[ 2.859389] pci 0000:00:14.0: [1022:780b] type 00 class 0x0c0500
[ 2.859554] pci 0000:00:14.2: [1022:780d] type 00 class 0x040300
[ 2.859601] pci 0000:00:14.2: reg 10: [mem 0xf0440000-0xf0443fff 64bit]
[ 2.859758] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[ 2.859798] pci 0000:00:14.3: [1022:780e] type 00 class 0x060100
[ 2.859954] pci 0000:00:14.4: [1022:780f] type 01 class 0x060401
[ 2.860046] pci 0000:00:14.5: [1022:7809] type 00 class 0x0c0310
[ 2.860072] pci 0000:00:14.5: reg 10: [mem 0xf044a000-0xf044afff]
[ 2.860226] pci 0000:00:15.0: [1022:43a0] type 01 class 0x060400
[ 2.860429] pci 0000:00:15.0: supports D1 D2
[ 2.860487] pci 0000:00:15.1: [1022:43a1] type 01 class 0x060400
[ 2.860656] pci 0000:00:15.1: supports D1 D2
[ 2.860712] pci 0000:00:15.2: [1022:43a2] type 01 class 0x060400
[ 2.860880] pci 0000:00:15.2: supports D1 D2
[ 2.860939] pci 0000:00:16.0: [1022:7807] type 00 class 0x0c0310
[ 2.860966] pci 0000:00:16.0: reg 10: [mem 0xf0449000-0xf0449fff]
[ 2.861116] pci 0000:00:16.2: [1022:7808] type 00 class 0x0c0320
[ 2.861154] pci 0000:00:16.2: reg 10: [mem 0xf0448000-0xf04480ff]
[ 2.861355] pci 0000:00:16.2: supports D1 D2
[ 2.861361] pci 0000:00:16.2: PME# supported from D0 D1 D2 D3hot
[ 2.861419] pci 0000:00:18.0: [1022:1700] type 00 class 0x060000
[ 2.861518] pci 0000:00:18.1: [1022:1701] type 00 class 0x060000
[ 2.861607] pci 0000:00:18.2: [1022:1702] type 00 class 0x060000
[ 2.861701] pci 0000:00:18.3: [1022:1703] type 00 class 0x060000
[ 2.861824] pci 0000:00:18.4: [1022:1704] type 00 class 0x060000
[ 2.861912] pci 0000:00:18.5: [1022:1718] type 00 class 0x060000
[ 2.862000] pci 0000:00:18.6: [1022:1716] type 00 class 0x060000
[ 2.862088] pci 0000:00:18.7: [1022:1719] type 00 class 0x060000
[ 2.862290] pci_bus 0000:01: busn_res: [bus 01] is inserted under [bus 00-ff]
[ 2.862390] pci 0000:00:14.4: PCI bridge to [bus 01] (subtractive decode)
[ 2.862411] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 2.862416] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 2.862422] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 2.862428] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000c3fff] (subtractive decode)
[ 2.862434] pci 0000:00:14.4: bridge window [mem 0x000c4000-0x000c7fff] (subtractive decode)
[ 2.862440] pci 0000:00:14.4: bridge window [mem 0x000c8000-0x000cbfff] (subtractive decode)
[ 2.862446] pci 0000:00:14.4: bridge window [mem 0x000d0000-0x000d3fff] (subtractive decode)
[ 2.862451] pci 0000:00:14.4: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
[ 2.862457] pci 0000:00:14.4: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
[ 2.862463] pci 0000:00:14.4: bridge window [mem 0x000dc000-0x000dffff] (subtractive decode)
[ 2.862469] pci 0000:00:14.4: bridge window [mem 0x000e0000-0x000e3fff] (subtractive decode)
[ 2.862475] pci 0000:00:14.4: bridge window [mem 0x000e4000-0x000e7fff] (subtractive decode)
[ 2.862481] pci 0000:00:14.4: bridge window [mem 0x000e8000-0x000ebfff] (subtractive decode)
[ 2.862488] pci 0000:00:14.4: bridge window [mem 0x000ec000-0x000effff] (subtractive decode)
[ 2.862494] pci 0000:00:14.4: bridge window [mem 0xe0000000-0xf7ffffff] (subtractive decode)
[ 2.862500] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfed3ffff] (subtractive decode)
[ 2.862506] pci 0000:00:14.4: bridge window [mem 0xfed45000-0xffffffff] (subtractive decode)
[ 2.862650] pci_bus 0000:02: busn_res: [bus 02-05] is inserted under [bus 00-ff]
[ 2.862660] pci 0000:00:15.0: PCI bridge to [bus 02-05]
[ 2.862674] pci 0000:00:15.0: bridge window [io 0x4000-0x4fff]
[ 2.862685] pci 0000:00:15.0: bridge window [mem 0xf0300000-0xf03fffff]
[ 2.862700] pci 0000:00:15.0: bridge window [mem 0xf0000000-0xf00fffff 64bit pref]
[ 2.862807] pci_bus 0000:06: busn_res: [bus 06] is inserted under [bus 00-ff]
[ 2.862852] pci 0000:06:00.0: [10ec:8176] type 00 class 0x028000
[ 2.862886] pci 0000:06:00.0: reg 10: [io 0x3000-0x30ff]
[ 2.862944] pci 0000:06:00.0: reg 18: [mem 0xf0200000-0xf0203fff 64bit]
[ 2.863123] pci 0000:06:00.0: supports D1 D2
[ 2.863129] pci 0000:06:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 2.865340] pci 0000:00:15.1: PCI bridge to [bus 06]
[ 2.865364] pci 0000:00:15.1: bridge window [io 0x3000-0x3fff]
[ 2.865381] pci 0000:00:15.1: bridge window [mem 0xf0200000-0xf02fffff]
[ 2.865504] pci_bus 0000:07: busn_res: [bus 07] is inserted under [bus 00-ff]
[ 2.865546] pci 0000:07:00.0: [10ec:8136] type 00 class 0x020000
[ 2.865578] pci 0000:07:00.0: reg 10: [io 0x2000-0x20ff]
[ 2.865634] pci 0000:07:00.0: reg 18: [mem 0xf0104000-0xf0104fff 64bit pref]
[ 2.865670] pci 0000:07:00.0: reg 20: [mem 0xf0100000-0xf0103fff 64bit pref]
[ 2.865818] pci 0000:07:00.0: supports D1 D2
[ 2.865824] pci 0000:07:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 2.867341] pci 0000:00:15.2: PCI bridge to [bus 07]
[ 2.867407] pci 0000:00:15.2: bridge window [io 0x2000-0x2fff]
[ 2.867428] pci 0000:00:15.2: bridge window [mem 0xf0100000-0xf01fffff 64bit pref]
[ 2.867479] pci_bus 0000:00: on NUMA node 0
[ 2.867496] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 2.868164] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SPB0._PRT]
[ 2.868334] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SPB1._PRT]
[ 2.868487] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SPB2._PRT]
[ 2.868866] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[ 2.869540] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 2.870298] pci0000:00: ACPI _OSC control (0x1d) granted
[ 2.928637] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 2.928957] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 2.929364] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 2.929677] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 2.929956] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 2.930213] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 2.930462] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 2.930705] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 2.932034] vgaarb: device added: PCI:0000:00:01.0,decodes=io+mem,owns=io+mem,locks=none
[ 2.932106] vgaarb: loaded
[ 2.932110] vgaarb: bridge control possible 0000:00:01.0
[ 2.932985] SCSI subsystem initialized
[ 2.932993] ACPI: bus type scsi registered
[ 2.933494] libata version 3.00 loaded.
[ 2.934799] PCI: Using ACPI for IRQ routing
[ 2.938165] PCI: pci_cache_line_size set to 64 bytes
[ 2.938539] e820: reserve RAM buffer [mem 0x0009f800-0x0009ffff]
[ 2.938547] e820: reserve RAM buffer [mem 0xdf6bf000-0xdfffffff]
[ 2.938556] e820: reserve RAM buffer [mem 0xdfc00000-0xdfffffff]
[ 2.938562] e820: reserve RAM buffer [mem 0x107000000-0x107ffffff]
[ 2.940137] Switching to clocksource hpet
[ 2.994143] pnp: PnP ACPI init
[ 2.994229] ACPI: bus type pnp registered
[ 2.994638] pnp 00:00: [bus 00-ff]
[ 2.994647] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 2.994653] pnp 00:00: [io 0x0d00-0xffff window]
[ 2.994660] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 2.994665] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 2.994671] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 2.994773] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 2.994779] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 2.994784] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 2.994795] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 2.994800] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 2.994805] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 2.994810] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 2.994816] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 2.994821] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 2.994826] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 2.994832] pnp 00:00: [mem 0xe0000000-0xf7ffffff window]
[ 2.994838] pnp 00:00: [mem 0xfc000000-0xfed3ffff window]
[ 2.994843] pnp 00:00: [mem 0xfed45000-0xffffffff window]
[ 2.994848] pnp 00:00: [io 0x0cf8-0x0cff]
[ 2.995430] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 2.995593] pnp 00:01: [mem 0xfec00000-0xfec00fff]
[ 2.995599] pnp 00:01: [mem 0xfee00000-0xfee00fff]
[ 2.996118] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 2.996126] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[ 2.996142] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 2.996717] pnp 00:02: [irq 0 disabled]
[ 2.996734] pnp 00:02: [irq 8]
[ 2.996741] pnp 00:02: [mem 0xfed00000-0xfed003ff]
[ 2.997051] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
[ 2.997439] pnp 00:03: [io 0x0000-0x000f]
[ 2.997445] pnp 00:03: [io 0x0081-0x008f]
[ 2.997450] pnp 00:03: [io 0x00c0-0x00df]
[ 2.997456] pnp 00:03: [dma 4]
[ 2.997858] pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active)
[ 2.997894] pnp 00:04: [io 0x00f0-0x00fe]
[ 2.997905] pnp 00:04: [irq 13]
[ 2.998265] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 2.998450] pnp 00:05: [io 0x0070-0x0071]
[ 2.998849] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 2.998883] pnp 00:06: [io 0x0061]
[ 2.999277] pnp 00:06: Plug and Play ACPI device, IDs PNP0800 (active)
[ 2.999334] pnp 00:07: [io 0x0060]
[ 2.999340] pnp 00:07: [io 0x0064]
[ 2.999351] pnp 00:07: [irq 1]
[ 2.999796] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[ 2.999836] pnp 00:08: [irq 12]
[ 3.000210] pnp 00:08: Plug and Play ACPI device, IDs TOS0310 PNP0f13 (active)
[ 3.000251] pnp 00:09: [io 0x0010-0x001f]
[ 3.000256] pnp 00:09: [io 0x002e-0x002f]
[ 3.000262] pnp 00:09: [io 0x0072-0x0073]
[ 3.000267] pnp 00:09: [io 0x0080]
[ 3.000272] pnp 00:09: [io 0x00b0-0x00b1]
[ 3.000276] pnp 00:09: [io 0x0092]
[ 3.000281] pnp 00:09: [io 0x025c-0x025d]
[ 3.000286] pnp 00:09: [io 0x0400-0x04cf]
[ 3.000291] pnp 00:09: [io 0x04d0-0x04d1]
[ 3.000301] pnp 00:09: [io 0x04d6]
[ 3.000305] pnp 00:09: [io 0x0680-0x06ff]
[ 3.000310] pnp 00:09: [io 0x077a]
[ 3.000315] pnp 00:09: [io 0x0c00-0x0c01]
[ 3.000319] pnp 00:09: [io 0x0c14]
[ 3.000324] pnp 00:09: [io 0x0c50-0x0c52]
[ 3.000328] pnp 00:09: [io 0x0c6c]
[ 3.000333] pnp 00:09: [io 0x0c6f]
[ 3.000338] pnp 00:09: [io 0x0cd0-0x0cdb]
[ 3.000342] pnp 00:09: [io 0x0840-0x0847]
[ 3.000878] system 00:09: [io 0x025c-0x025d] has been reserved
[ 3.000886] system 00:09: [io 0x0400-0x04cf] has been reserved
[ 3.000892] system 00:09: [io 0x04d0-0x04d1] has been reserved
[ 3.000899] system 00:09: [io 0x04d6] has been reserved
[ 3.000906] system 00:09: [io 0x0680-0x06ff] has been reserved
[ 3.000913] system 00:09: [io 0x077a] has been reserved
[ 3.000919] system 00:09: [io 0x0c00-0x0c01] has been reserved
[ 3.000926] system 00:09: [io 0x0c14] has been reserved
[ 3.000932] system 00:09: [io 0x0c50-0x0c52] has been reserved
[ 3.000938] system 00:09: [io 0x0c6c] has been reserved
[ 3.000945] system 00:09: [io 0x0c6f] has been reserved
[ 3.000952] system 00:09: [io 0x0cd0-0x0cdb] has been reserved
[ 3.000959] system 00:09: [io 0x0840-0x0847] has been reserved
[ 3.000973] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 3.001136] pnp 00:0a: [mem 0x000e0000-0x000fffff]
[ 3.001143] pnp 00:0a: [mem 0xffe00000-0xffffffff]
[ 3.001626] system 00:0a: [mem 0x000e0000-0x000fffff] could not be reserved
[ 3.001634] system 00:0a: [mem 0xffe00000-0xffffffff] has been reserved
[ 3.001646] system 00:0a: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 3.003450] pnp: PnP ACPI: found 11 devices
[ 3.003456] ACPI: ACPI bus type pnp unregistered
[ 3.062483] pci 0000:00:14.4: PCI bridge to [bus 01]
[ 3.062517] pci 0000:00:15.0: PCI bridge to [bus 02-05]
[ 3.062526] pci 0000:00:15.0: bridge window [io 0x4000-0x4fff]
[ 3.062538] pci 0000:00:15.0: bridge window [mem 0xf0300000-0xf03fffff]
[ 3.062549] pci 0000:00:15.0: bridge window [mem 0xf0000000-0xf00fffff 64bit pref]
[ 3.062563] pci 0000:00:15.1: PCI bridge to [bus 06]
[ 3.062571] pci 0000:00:15.1: bridge window [io 0x3000-0x3fff]
[ 3.062583] pci 0000:00:15.1: bridge window [mem 0xf0200000-0xf02fffff]
[ 3.062600] pci 0000:00:15.2: PCI bridge to [bus 07]
[ 3.062652] pci 0000:00:15.2: bridge window [io 0x2000-0x2fff]
[ 3.062669] pci 0000:00:15.2: bridge window [mem 0xf0100000-0xf01fffff 64bit pref]
[ 3.062758] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 3.062765] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 3.062770] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 3.062776] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff]
[ 3.062782] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff]
[ 3.062789] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff]
[ 3.062795] pci_bus 0000:00: resource 10 [mem 0x000d0000-0x000d3fff]
[ 3.062800] pci_bus 0000:00: resource 11 [mem 0x000d4000-0x000d7fff]
[ 3.062806] pci_bus 0000:00: resource 12 [mem 0x000d8000-0x000dbfff]
[ 3.062812] pci_bus 0000:00: resource 13 [mem 0x000dc000-0x000dffff]
[ 3.062818] pci_bus 0000:00: resource 14 [mem 0x000e0000-0x000e3fff]
[ 3.062824] pci_bus 0000:00: resource 15 [mem 0x000e4000-0x000e7fff]
[ 3.062829] pci_bus 0000:00: resource 16 [mem 0x000e8000-0x000ebfff]
[ 3.062835] pci_bus 0000:00: resource 17 [mem 0x000ec000-0x000effff]
[ 3.062840] pci_bus 0000:00: resource 18 [mem 0xe0000000-0xf7ffffff]
[ 3.062846] pci_bus 0000:00: resource 19 [mem 0xfc000000-0xfed3ffff]
[ 3.062852] pci_bus 0000:00: resource 20 [mem 0xfed45000-0xffffffff]
[ 3.062859] pci_bus 0000:01: resource 4 [io 0x0000-0x0cf7]
[ 3.062864] pci_bus 0000:01: resource 5 [io 0x0d00-0xffff]
[ 3.062869] pci_bus 0000:01: resource 6 [mem 0x000a0000-0x000bffff]
[ 3.062875] pci_bus 0000:01: resource 7 [mem 0x000c0000-0x000c3fff]
[ 3.062881] pci_bus 0000:01: resource 8 [mem 0x000c4000-0x000c7fff]
[ 3.062887] pci_bus 0000:01: resource 9 [mem 0x000c8000-0x000cbfff]
[ 3.062892] pci_bus 0000:01: resource 10 [mem 0x000d0000-0x000d3fff]
[ 3.062898] pci_bus 0000:01: resource 11 [mem 0x000d4000-0x000d7fff]
[ 3.062903] pci_bus 0000:01: resource 12 [mem 0x000d8000-0x000dbfff]
[ 3.062909] pci_bus 0000:01: resource 13 [mem 0x000dc000-0x000dffff]
[ 3.062916] pci_bus 0000:01: resource 14 [mem 0x000e0000-0x000e3fff]
[ 3.062922] pci_bus 0000:01: resource 15 [mem 0x000e4000-0x000e7fff]
[ 3.062927] pci_bus 0000:01: resource 16 [mem 0x000e8000-0x000ebfff]
[ 3.062933] pci_bus 0000:01: resource 17 [mem 0x000ec000-0x000effff]
[ 3.062940] pci_bus 0000:01: resource 18 [mem 0xe0000000-0xf7ffffff]
[ 3.062946] pci_bus 0000:01: resource 19 [mem 0xfc000000-0xfed3ffff]
[ 3.062951] pci_bus 0000:01: resource 20 [mem 0xfed45000-0xffffffff]
[ 3.062957] pci_bus 0000:02: resource 0 [io 0x4000-0x4fff]
[ 3.062962] pci_bus 0000:02: resource 1 [mem 0xf0300000-0xf03fffff]
[ 3.062968] pci_bus 0000:02: resource 2 [mem 0xf0000000-0xf00fffff 64bit pref]
[ 3.062974] pci_bus 0000:06: resource 0 [io 0x3000-0x3fff]
[ 3.062979] pci_bus 0000:06: resource 1 [mem 0xf0200000-0xf02fffff]
[ 3.062986] pci_bus 0000:07: resource 0 [io 0x2000-0x2fff]
[ 3.062991] pci_bus 0000:07: resource 2 [mem 0xf0100000-0xf01fffff 64bit pref]
[ 3.063109] NET: Registered protocol family 2
[ 3.063862] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 3.065000] TCP bind hash table entries: 65536 (order: 9, 2359296 bytes)
[ 3.077721] TCP: Hash tables configured (established 131072 bind 65536)
[ 3.077852] TCP: reno registered
[ 3.077871] UDP hash table entries: 512 (order: 3, 40960 bytes)
[ 3.078072] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes)
[ 3.078520] NET: Registered protocol family 1
[ 3.078568] pci 0000:00:01.0: Boot video device
[ 3.079258] PCI: CLS 64 bytes, default 64
[ 3.079529] Trying to unpack rootfs image as initramfs...
[ 3.579467] Freeing initrd memory: 8460k freed
[ 3.586154] Simple Boot Flag at 0x44 set to 0x1
[ 3.586463] LVT offset 0 assigned for vector 0x400
[ 3.586556] perf: AMD IBS detected (0x000000ff)
[ 3.590965] bounce pool size: 64 pages
[ 3.616441] msgmni has been set to 1692
[ 3.617758] io scheduler noop registered
[ 3.617766] io scheduler deadline registered (default)
[ 3.618844] pcieport 0000:00:15.0: irq 40 for MSI/MSI-X
[ 3.619536] pcieport 0000:00:15.1: irq 41 for MSI/MSI-X
[ 3.620065] pcieport 0000:00:15.2: irq 42 for MSI/MSI-X
[ 3.620989] pcieport 0000:00:15.0: Signaling PME through PCIe PME interrupt
[ 3.621080] pcie_pme 0000:00:15.0:pcie01: service driver pcie_pme loaded
[ 3.621156] pcieport 0000:00:15.1: Signaling PME through PCIe PME interrupt
[ 3.621164] pci 0000:06:00.0: Signaling PME through PCIe PME interrupt
[ 3.621210] pcie_pme 0000:00:15.1:pcie01: service driver pcie_pme loaded
[ 3.621283] pcieport 0000:00:15.2: Signaling PME through PCIe PME interrupt
[ 3.621290] pci 0000:07:00.0: Signaling PME through PCIe PME interrupt
[ 3.621337] pcie_pme 0000:00:15.2:pcie01: service driver pcie_pme loaded
[ 3.623869] ACPI: acpi_idle registered with cpuidle
[ 3.651590] Linux agpgart interface v0.103
[ 3.663821] brd: module loaded
[ 3.664818] ahci 0000:00:11.0: version 3.0
[ 3.665398] ahci 0000:00:11.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[ 3.665408] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
[ 3.668683] scsi0 : ahci
[ 3.669793] scsi1 : ahci
[ 3.670420] ata1: SATA max UDMA/133 abar m2048@0xf044f000 port 0xf044f100 irq 19
[ 3.670428] ata2: SATA max UDMA/133 abar m2048@0xf044f000 port 0xf044f180 irq 19
[ 3.674366] sky2: driver version 1.30
[ 3.675234] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 3.675612] r8169 0000:07:00.0: irq 43 for MSI/MSI-X
[ 3.676966] r8169 0000:07:00.0: eth0: RTL8105e at 0xf842a000, 4c:72:b9:64:6c:52, XID 00c00000 IRQ 43
[ 3.678466] i8042: PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 3.681223] i8042: Detected active multiplexing controller, rev 1.1
[ 3.683248] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.683345] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 3.683871] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 3.684021] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 3.684033] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 3.685899] mousedev: PS/2 mouse device common for all mice
[ 3.687669] rtc_cmos 00:05: RTC can wake from S4
[ 3.688666] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 3.688795] rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
[ 3.689175] cpuidle: using governor ladder
[ 3.689701] cpuidle: using governor menu
[ 3.691783] TCP: cubic registered
[ 3.691794] NET: Registered protocol family 17
[ 3.692129] Key type dns_resolver registered
[ 3.693160] Using IPI No-Shortcut mode
[ 3.694119] registered taskstats version 1
[ 3.695766] console [netcon0] enabled
[ 3.695771] netconsole: network logging started
[ 3.695885] rtc_cmos 00:05: setting system clock to 2012-09-05 18:12:53 UTC (1346868773)
[ 3.884108] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 4.630202] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.630362] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.632268] ata1.00: ATA-8: Hitachi HTS543232A7A384, ES2OA70K, max UDMA/133
[ 4.632284] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 4.634622] ata2.00: ATAPI: TSSTcorp CDDVDW SN-208AB, TO03, max UDMA/100
[ 4.634671] ata1.00: configured for UDMA/133
[ 4.636126] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54323 ES2O PQ: 0 ANSI: 5
[ 4.638652] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 4.638865] sd 0:0:0:0: [sda] Write Protect is off
[ 4.638873] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.638962] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.642213] ata2.00: configured for UDMA/100
[ 4.643170] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.651572] scsi 1:0:0:0: CD-ROM TSSTcorp CDDVDW SN-208AB TO03 PQ: 0 ANSI: 5
[ 4.666170] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 4.666181] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 4.667668] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 4.668704] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 5.070415] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
[ 5.075322] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.075678] Freeing unused kernel memory: 484k freed
[ 5.076260] Write protecting the kernel text: 3652k
[ 5.076485] Write protecting the kernel read-only data: 1740k
[ 5.076496] NX-protecting the kernel data: 4540k
[ 5.087945] tsc: Refined TSC clocksource calibration: 1397.458 MHz
[ 5.087984] Switching to clocksource tsc
[ 5.139116] udev: starting version 160
[ 5.139317] udevd (695): /proc/695/oom_adj is deprecated, please use /proc/695/oom_score_adj instead.
[ 5.289843] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 5.297479] ACPI: Power Button [PWRB]
[ 5.300657] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[ 5.347079] ACPI: Lid Switch [LID]
[ 5.348521] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 5.348719] ACPI: Power Button [PWRF]
[ 5.380769] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 5.381472] thermal LNXTHERM:00: registered as thermal_zone0
[ 5.381478] ACPI: Thermal Zone [THZ0] (50 C)
[ 5.403167] ACPI: Fan [Z0F0] (off)
[ 5.403463] ACPI: Fan [Z0F1] (off)
[ 5.403686] ACPI: Fan [Z0F2] (off)
[ 5.403903] ACPI: Fan [Z0F3] (off)
[ 5.405435] acpi device:01: registered as cooling_device5
[ 5.405607] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 5.405883] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input4
[ 5.680959] ACPI: bus type usb registered
[ 5.681131] usbcore: registered new interface driver usbfs
[ 5.681274] usbcore: registered new interface driver hub
[ 5.715183] usbcore: registered new device driver usb
[ 5.716452] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.716724] ehci_hcd 0000:00:12.2: EHCI Host Controller
[ 5.717132] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
[ 5.717246] QUIRK: Enable AMD PLL fix
[ 5.717255] ehci_hcd 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 5.717566] ehci_hcd 0000:00:12.2: debug port 1
[ 5.718984] [drm] Initialized drm 1.1.0 20060810
[ 5.734828] ehci_hcd 0000:00:12.2: irq 17, io mem 0xf044d000
[ 5.750880] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 5.751336] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.751344] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.751350] usb usb1: Product: EHCI Host Controller
[ 5.751356] usb usb1: Manufacturer: Linux 3.5.0 ehci_hcd
[ 5.751361] usb usb1: SerialNumber: 0000:00:12.2
[ 5.793181] psmouse serio2: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000, board id: 3655, fw id: 582762
[ 5.812310] hub 1-0:1.0: USB hub found
[ 5.812409] hub 1-0:1.0: 5 ports detected
[ 5.828971] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input5
[ 5.839110] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 5.839167] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
[ 5.839187] ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 5.839286] ehci_hcd 0000:00:13.2: debug port 1
[ 5.839319] ehci_hcd 0000:00:13.2: irq 17, io mem 0xf044b000
[ 5.844862] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 5.845061] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.845068] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.845074] usb usb2: Product: EHCI Host Controller
[ 5.845079] usb usb2: Manufacturer: Linux 3.5.0 ehci_hcd
[ 5.845084] usb usb2: SerialNumber: 0000:00:13.2
[ 5.848151] hub 2-0:1.0: USB hub found
[ 5.848177] hub 2-0:1.0: 5 ports detected
[ 5.857819] ehci_hcd 0000:00:16.2: EHCI Host Controller
[ 5.857853] ehci_hcd 0000:00:16.2: new USB bus registered, assigned bus number 3
[ 5.857871] ehci_hcd 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 5.857971] ehci_hcd 0000:00:16.2: debug port 1
[ 5.858005] ehci_hcd 0000:00:16.2: irq 17, io mem 0xf0448000
[ 5.863833] ehci_hcd 0000:00:16.2: USB 2.0 started, EHCI 1.00
[ 5.863945] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.863952] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.863958] usb usb3: Product: EHCI Host Controller
[ 5.863963] usb usb3: Manufacturer: Linux 3.5.0 ehci_hcd
[ 5.863968] usb usb3: SerialNumber: 0000:00:16.2
[ 5.867463] hub 3-0:1.0: USB hub found
[ 5.867489] hub 3-0:1.0: 4 ports detected
[ 5.915818] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.916095] ohci_hcd 0000:00:12.0: OHCI Host Controller
[ 5.916126] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 4
[ 5.916867] ohci_hcd 0000:00:12.0: irq 18, io mem 0xf044e000
[ 5.951572] [drm] radeon kernel modesetting enabled.
[ 5.972055] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.972066] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.972072] usb usb4: Product: OHCI Host Controller
[ 5.972078] usb usb4: Manufacturer: Linux 3.5.0 ohci_hcd
[ 5.972083] usb usb4: SerialNumber: 0000:00:12.0
[ 5.976285] hub 4-0:1.0: USB hub found
[ 5.976381] hub 4-0:1.0: 5 ports detected
[ 5.989043] [drm] initializing kernel modesetting (PALM 0x1002:0x9809 0x1179:0xFB33).
[ 5.989178] [drm] register mmio base: 0xF0400000
[ 5.989183] [drm] register mmio size: 262144
[ 5.998414] ATOM BIOS: AMD
[ 5.998506] radeon 0000:00:01.0: VRAM: 384M 0x0000000000000000 - 0x0000000017FFFFFF (384M used)
[ 5.998515] radeon 0000:00:01.0: GTT: 512M 0x0000000018000000 - 0x0000000037FFFFFF
[ 6.003047] [drm] Detected VRAM RAM=384M, BAR=256M
[ 6.003056] [drm] RAM width 32bits DDR
[ 6.007275] [TTM] Zone kernel: Available graphics memory: 433404 kiB
[ 6.007285] [TTM] Zone highmem: Available graphics memory: 1864320 kiB
[ 6.007289] [TTM] Initializing pool allocator
[ 6.008457] [drm] radeon: 384M of VRAM memory ready
[ 6.008466] [drm] radeon: 512M of GTT memory ready.
[ 6.018996] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 6.019006] [drm] Driver supports precise vblank timestamp query.
[ 6.019221] radeon 0000:00:01.0: irq 44 for MSI/MSI-X
[ 6.019267] radeon 0000:00:01.0: radeon: using MSI.
[ 6.019463] [drm] radeon: irq initialized.
[ 6.019476] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 6.028806] [drm] Loading PALM Microcode
[ 6.075353] [drm] PCIE GART of 512M enabled (table at 0x0000000000040000).
[ 6.075880] radeon 0000:00:01.0: WB enabled
[ 6.075890] radeon 0000:00:01.0: fence driver on ring 0 use gpu addr 0x0000000018000c00 and cpu addr 0xffc8cc00
[ 6.093926] [drm] ring test on 0 succeeded in 1 usecs
[ 6.095034] [drm] ib test on ring 0 succeeded in 0 usecs
[ 6.098272] [drm] Radeon Display Connectors
[ 6.098281] [drm] Connector 0:
[ 6.098285] [drm] LVDS-1
[ 6.098288] [drm] HPD1
[ 6.098294] [drm] DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438 0x643c 0x643c
[ 6.098298] [drm] Encoders:
[ 6.098302] [drm] LCD1: INTERNAL_UNIPHY
[ 6.098305] [drm] Connector 1:
[ 6.098309] [drm] HDMI-A-1
[ 6.098312] [drm] HPD2
[ 6.098317] [drm] DDC: 0x6440 0x6440 0x6444 0x6444 0x6448 0x6448 0x644c 0x644c
[ 6.098320] [drm] Encoders:
[ 6.098323] [drm] DFP1: INTERNAL_UNIPHY
[ 6.098326] [drm] Connector 2:
[ 6.098330] [drm] VGA-1
[ 6.098335] [drm] DDC: 0x64d8 0x64d8 0x64dc 0x64dc 0x64e0 0x64e0 0x64e4 0x64e4
[ 6.098338] [drm] Encoders:
[ 6.098341] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 6.098842] [drm] Internal thermal controller without fan control
[ 6.099490] [drm] radeon: power management initialized
[ 6.149667] usb 2-3: new high-speed USB device number 2 using ehci_hcd
[ 6.278007] usb 2-3: New USB device found, idVendor=0bda, idProduct=0138
[ 6.278025] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 6.278035] usb 2-3: Product: USB2.0-CRW
[ 6.278044] usb 2-3: Manufacturer: Generic
[ 6.278053] usb 2-3: SerialNumber: 20090516388200000
[ 6.294818] Initializing USB Mass Storage driver...
[ 6.295402] scsi2 : usb-storage 2-3:1.0
[ 6.296452] usbcore: registered new interface driver usb-storage
[ 6.296459] USB Mass Storage support registered.
[ 6.387268] usb 2-4: new high-speed USB device number 3 using ehci_hcd
[ 6.532474] [drm] fb mappable at 0xE0142000
[ 6.532483] [drm] vram apper at 0xE0000000
[ 6.532486] [drm] size 4325376
[ 6.532490] [drm] fb depth is 24
[ 6.532493] [drm] pitch is 5632
[ 6.534257] fbcon: radeondrmfb (fb0) is primary device
[ 6.639970] usb 2-4: New USB device found, idVendor=04f2, idProduct=b307
[ 6.639979] usb 2-4: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 6.639985] usb 2-4: Product: TOSHIBA Web Camera - HD
[ 6.639991] usb 2-4: Manufacturer: Chicony Electronics Co.,Ltd.
[ 6.639996] usb 2-4: SerialNumber: 0x0001
[ 7.081095] Console: switching to colour frame buffer device 170x48
[ 7.090618] fb0: radeondrmfb frame buffer device
[ 7.090619] drm: registered panic notifier
[ 7.090955] [drm] Initialized radeon 2.17.0 20080528 for 0000:00:01.0 on minor 0
[ 7.091299] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 7.091328] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
[ 7.091418] ohci_hcd 0000:00:13.0: irq 18, io mem 0xf044c000
[ 7.146871] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 7.146882] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.146888] usb usb5: Product: OHCI Host Controller
[ 7.146894] usb usb5: Manufacturer: Linux 3.5.0 ohci_hcd
[ 7.146899] usb usb5: SerialNumber: 0000:00:13.0
[ 7.147910] hub 5-0:1.0: USB hub found
[ 7.148003] hub 5-0:1.0: 5 ports detected
[ 7.148641] ohci_hcd 0000:00:14.5: OHCI Host Controller
[ 7.148669] ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 6
[ 7.148752] ohci_hcd 0000:00:14.5: irq 18, io mem 0xf044a000
[ 7.203647] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 7.203658] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.203664] usb usb6: Product: OHCI Host Controller
[ 7.203669] usb usb6: Manufacturer: Linux 3.5.0 ohci_hcd
[ 7.203674] usb usb6: SerialNumber: 0000:00:14.5
[ 7.204547] hub 6-0:1.0: USB hub found
[ 7.204571] hub 6-0:1.0: 2 ports detected
[ 7.205190] ohci_hcd 0000:00:16.0: OHCI Host Controller
[ 7.205219] ohci_hcd 0000:00:16.0: new USB bus registered, assigned bus number 7
[ 7.205306] ohci_hcd 0000:00:16.0: irq 18, io mem 0xf0449000
[ 7.260589] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 7.260600] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.260606] usb usb7: Product: OHCI Host Controller
[ 7.260612] usb usb7: Manufacturer: Linux 3.5.0 ohci_hcd
[ 7.260617] usb usb7: SerialNumber: 0000:00:16.0
[ 7.261401] hub 7-0:1.0: USB hub found
[ 7.261472] hub 7-0:1.0: 4 ports detected
[ 7.302300] scsi 2:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS
[ 7.303786] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 7.311825] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 7.678264] kjournald starting. Commit interval 5 seconds
[ 7.678463] EXT3-fs (sda5): mounted filesystem with ordered data mode
[ 7.741890] kjournald starting. Commit interval 5 seconds
[ 7.741969] EXT3-fs (sda7): mounted filesystem with ordered data mode
[ 9.882200] udev: starting version 160
[ 10.333808] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 10.334140] wmi: Mapper loaded
[ 10.377814] ACPI: AC Adapter [AC0] (on-line)
[ 10.446692] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 10.446748] ACPI: Battery Slot [BAT0] (battery present)
[ 10.727404] ACPI Warning: 0x00000b00-0x00000b07 SystemIO conflicts with Region \_SB_.PCI0.SMBS.SMB0 1 (20120711/utaddress-251)
[ 10.727427] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 10.979174] microcode: CPU0: patch_level=0x0500010d
[ 10.981314] Linux video capture interface: v2.00
[ 11.160691] uvcvideo: Found UVC 1.00 device TOSHIBA Web Camera - HD (04f2:b307)
[ 11.173597] input: TOSHIBA Web Camera - HD as /devices/pci0000:00/0000:00:13.2/usb2/2-4/2-4:1.0/input/input6
[ 11.174894] usbcore: registered new interface driver uvcvideo
[ 11.174901] USB Video Class driver (1.1.1)
[ 11.261831] snd_hda_intel 0000:00:01.1: irq 45 for MSI/MSI-X
[ 11.293621] input: HD-Audio Generic HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.1/sound/card2/input7
[ 11.311941] snd_hda_intel 0000:00:14.2: irq 46 for MSI/MSI-X
[ 11.375724] input: HD-Audio Generic Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input8
[ 11.376438] input: HD-Audio Generic Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input9
[ 11.442385] microcode: failed to load file amd-ucode/microcode_amd.bin
[ 11.444535] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 11.498486] powernow-k8: Found 1 AMD E1-1200 APU with Radeon(tm) HD Graphics (1 cpu cores) (version 2.20.00)
[ 11.498633] powernow-k8: 0 : pstate 0 (1400 MHz)
[ 11.498639] powernow-k8: 1 : pstate 1 (1166 MHz)
[ 11.498643] powernow-k8: 2 : pstate 2 (777 MHz)
[ 13.383848] Adding 1048572k swap on /dev/sda6. Priority:-1 extents:1 across:1048572k
[ 25.568669] kjournald starting. Commit interval 5 seconds
[ 25.569334] EXT3-fs (sda7): using internal journal
[ 25.569352] EXT3-fs (sda7): mounted filesystem with ordered data mode
[ 26.236551] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 28.025775] kjournald starting. Commit interval 5 seconds
[ 28.026256] EXT3-fs (sda8): using internal journal
[ 28.026268] EXT3-fs (sda8): mounted filesystem with ordered data mode
[ 28.143583] kjournald starting. Commit interval 5 seconds
[ 28.144514] EXT3-fs (sda9): using internal journal
[ 28.144533] EXT3-fs (sda9): mounted filesystem with ordered data mode
[ 30.920725] fuse init (API version 7.19)
[ 31.657279] r8169 0000:07:00.0: eth0: link down
[ 31.657585] r8169 0000:07:00.0: eth0: link down
[ 33.293384] r8169 0000:07:00.0: eth0: link up
[ 34.029275] device eth0 entered promiscuous mode
[ 35.042100] device eth0 left promiscuous mode
[ 35.052708] device eth0 entered promiscuous mode
[ 35.200657] NET: Registered protocol family 10
[ 36.059184] device eth0 left promiscuous mode
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: rtl8192ce: activation problem with rtl8188ce pci card
2012-09-05 16:55 rtl8192ce: activation problem with rtl8188ce pci card Anisse Astier
@ 2012-09-05 17:38 ` Larry Finger
2012-09-05 18:01 ` Anisse Astier
2012-09-05 18:14 ` Anisse Astier
0 siblings, 2 replies; 10+ messages in thread
From: Larry Finger @ 2012-09-05 17:38 UTC (permalink / raw)
To: Anisse Astier; +Cc: linux-wireless
On 09/05/2012 11:55 AM, Anisse Astier wrote:
> Hi,
>
> On a toshiba laptop (see dmesg attached), with a wireless-next kernel,
> this card doesn't seem to turn on:
> 01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02)
>
Unfortunately, the above is not a wireless device. It is your wired device.
> # modprobe rtl8192ce debug=4
> [ 6184.995319] cfg80211: Calling CRDA to update world regulatory domain
> [ 6185.103824] rtl8192ce: rtl8192ce: FW Power Save off (module option)
The above line is unexpected. Do you have a module option set in /etc/module.d/?
> [ 6185.103881] rtl8192ce: Using firmware rtlwifi/rtl8192cfw.bin
> [ 6185.150488] rtlwifi:rtl_fw_cb():<0-0> Firmware callback routine entered!
> [ 6185.216834] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
> [ 6185.224729] rtlwifi: wireless switch is on
> [ 6185.289544] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
> [ 6185.289649] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
> [ 6185.289797] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
> [ 6185.289944] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
> [ 6185.290092] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
> [ 6185.290250] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
> [ 6185.290398] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
> [ 6185.290545] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
> [ 6185.290693] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:98053f15:10
> [ 6185.291829] rtl8192c_common:rtl92c_download_fw():<0-0> Firmware Version(49), Signature(0x88c1),Size(32)
That is the firmware that I use.
> [ 6185.513223] rtl8192ce:rtl92ce_enable_hw_security_config():<0-0> PairwiseEncAlgorithm = 0 GroupEncAlgorithm = 0
> [ 6185.513237] rtl8192ce:rtl92ce_enable_hw_security_config():<0-0> The SECR-value cc
> [ 6185.622274] rtl8192c_common:rtl92c_dm_initialize_txpower_tracking_thermalmeter():<0-0> pMgntInfo->txpower_tracking = 1
> [ 6185.623129] rtlwifi:rtl_pci_start():<0-0> enable_interrupt OK
> [ 6185.623140] rtlwifi:rtl_pci_start():<0-0> OK
> [ 6185.624061] rtl8192c_common:rtl92c_dm_dynamic_bb_powersaving():<0-0> Not connected to any
> [ 6185.624073] rtl8192c_common:rtl92c_dm_dynamic_bb_powersaving():<0-0> AP Ext Port PWDB = 0x0
> [ 6185.624123] rtl8192c_common:rtl92c_dm_check_txpower_tracking_thermal_meter():<0-0> Trigger 92S Thermal Meter!!
> [ 6185.632970] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
> [ 6185.632987] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
> [ 6185.633028] rtlwifi:rtl_op_bss_info_changed():<0-0> BSS_CHANGED_ERP_PREAMBLE use short preamble:0
> [ 6185.633040] rtl8192ce:rtl92ce_set_hw_reg():<0-0> HW_VAR_SLOT_TIME 14
> [ 6185.633989] rtlwifi:rtl_op_config():<0-0> IEEE80211_CONF_CHANGE_LISTEN_INTERVAL
> [ 6185.634281] rtlwifi:rtl_op_config():<0-0> IEEE80211_CONF_CHANGE_RETRY_LIMITS 4
> [ 6185.644434] rtl8192c_common:rtl92c_phy_sw_chnl():<0-0> sw_chnl_inprogress false schdule workitem
> [ 6185.644445] rtl8192ce:rtl92ce_set_hw_reg():<0-0> HW_VAR_SLOT_TIME 14
> [ 6185.655245] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
> [ 6185.734598] rtl8192ce:_rtl92ce_phy_set_rf_power_state():<0-0> IPS Set eRf nic disable
> [ 6185.735117] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
> [ 6185.735129] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
> [ 6185.852489] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
> [ 6185.852504] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
> [ 6185.853211] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
> [ 6185.853221] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
> [ 6185.853823] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
> [ 6185.853833] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
> [...] this is repeated
>
> After a modprobe -r:
> [ 6187.127706] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
> [ 6187.127724] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
> [ 6187.130614] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
> [ 6187.130626] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
> [ 6187.130638] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 7
> [ 6187.130646] rtl8192ce:rtl92ce_sw_led_off():<0-0> LedAddr:4E ledpin=1
> [ 6187.139353] rtl8192c_common:rtl92c_firmware_selfreset(): 8051 reset fail
> [ 6187.139373] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 7
> [ 6187.139382] rtl8192ce:rtl92ce_sw_led_off():<0-0> LedAddr:4E ledpin=1
>
>
> After inserting the module, the PCI information is scrambled:
> 06:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8176 (rev ff) (prog-if ff)
> !!! Unknown header type 7f
This listing is likely for your wireless card.
> After a few seconds, the computer will freeze if the module isn't removed.
> The card works on Windows.
>
> This looks like a hidden rfkill, or maybe it is a different revision of
> the card. What do you think ?
Without a full 'sudo lspci -nnv' listing for the wireless, it is hard to tell if
it is a different revision. The rx descriptor unavailable message is a new one
for me.
I have two different revisions of the RTL8188CE card. The newer one, marked
RTL8188CE-VL, gives the following lspci output:
06:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE
802.11b/g/n WiFi Adapter [10ec:8176] (rev 01)
Subsystem: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi
Adapter [10ec:8176]
Flags: bus master, fast devsel, latency 0, IRQ 20
I/O ports at 4000 [size=256]
Memory at f8000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 01-91-81-fe-ff-4c-e0-00
Kernel driver in use: rtl8192ce
It certainly does not yield the rx descriptor problem. Please send the lspci
output when the driver has not been loaded.
Larry
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: rtl8192ce: activation problem with rtl8188ce pci card
2012-09-05 17:38 ` Larry Finger
@ 2012-09-05 18:01 ` Anisse Astier
2012-09-05 18:14 ` Anisse Astier
1 sibling, 0 replies; 10+ messages in thread
From: Anisse Astier @ 2012-09-05 18:01 UTC (permalink / raw)
To: Larry Finger; +Cc: linux-wireless
[-- Attachment #1: Type: text/plain, Size: 5567 bytes --]
On Wed, 05 Sep 2012 12:38:24 -0500, Larry Finger <Larry.Finger@lwfinger.net> wrote :
> On 09/05/2012 11:55 AM, Anisse Astier wrote:
> > Hi,
> >
> > On a toshiba laptop (see dmesg attached), with a wireless-next kernel,
> > this card doesn't seem to turn on:
> > 01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02)
> >
>
> Unfortunately, the above is not a wireless device. It is your wired device.
Indeed. This is embarassing. The mail had a full lspci attachement
planned which was forgotten. See attached file.
>
> > # modprobe rtl8192ce debug=4
> > [ 6184.995319] cfg80211: Calling CRDA to update world regulatory domain
> > [ 6185.103824] rtl8192ce: rtl8192ce: FW Power Save off (module option)
>
> The above line is unexpected. Do you have a module option set in /etc/module.d/?
Yes. This is related to another problem, see:
http://thread.gmane.org/gmane.linux.kernel.wireless.general/90954
New log with fwlps=1:
[ 84.532629] cfg80211: Calling CRDA to update world regulatory domain
[ 84.794759] rtl8192ce: Using firmware rtlwifi/rtl8192cfw.bin
[ 85.038881] rtlwifi:rtl_fw_cb():<0-0> Firmware callback routine entered!
[ 85.188013] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 85.195046] rtlwifi: wireless switch is on
[ 85.346058] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 85.346677] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 85.346799] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 85.348064] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 85.348885] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 85.360848] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 85.738594] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:1
[ 85.738699] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:1
[ 85.738847] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:1
[ 85.739089] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:1
[ 85.739238] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:1
[ 85.739385] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:1
[ 85.739533] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:1
[ 85.739680] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051e1b:1
[ 85.739827] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:98053f15:0
[ 85.740967] rtl8192c_common:rtl92c_download_fw():<0-0> Firmware Version(49), Signature(0x88c1),Size(32)
[ 85.962468] rtl8192ce:rtl92ce_enable_hw_security_config():<0-0> PairwiseEncAlgorithm = 0 GroupEncAlgorithm = 0
[ 85.962483] rtl8192ce:rtl92ce_enable_hw_security_config():<0-0> The SECR-value cc
[ 86.071504] rtl8192c_common:rtl92c_dm_initialize_txpower_tracking_thermalmeter():<0-0> pMgntInfo->txpower_tracking = 1
[ 86.071520] rtlwifi:rtl_pci_start():<0-0> enable_interrupt OK
[ 86.071528] rtlwifi:rtl_pci_start():<0-0> OK
[ 86.072201] rtl8192c_common:rtl92c_dm_dynamic_bb_powersaving():<0-0> Not connected to any
[ 86.072212] rtl8192c_common:rtl92c_dm_dynamic_bb_powersaving():<0-0> AP Ext Port PWDB = 0x0
[ 86.072257] rtl8192c_common:rtl92c_dm_check_txpower_tracking_thermal_meter():<0-0> Trigger 92S Thermal Meter!!
[ 86.091672] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
[ 86.091689] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
[ 86.091730] rtlwifi:rtl_op_bss_info_changed():<0-0> BSS_CHANGED_ERP_PREAMBLE use short preamble:0
[ 86.091742] rtl8192ce:rtl92ce_set_hw_reg():<0-0> HW_VAR_SLOT_TIME 14
[ 86.092343] rtlwifi:rtl_op_config():<0-0> IEEE80211_CONF_CHANGE_LISTEN_INTERVAL
[ 86.092674] rtlwifi:rtl_op_config():<0-0> IEEE80211_CONF_CHANGE_RETRY_LIMITS 4
[ 86.102832] rtl8192c_common:rtl92c_phy_sw_chnl():<0-0> sw_chnl_inprogress false schdule workitem
[ 86.102842] rtl8192ce:rtl92ce_set_hw_reg():<0-0> HW_VAR_SLOT_TIME 14
[ 86.114505] rtl8192ce:rtl92ce_led_control():<10000-1> ledaction 5
[ 86.136118] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 86.170054] rtl8192ce:rtl92ce_led_control():<10000-1> ledaction 5
[ 86.171709] rtl8192ce:rtl92ce_led_control():<10100-1> ledaction 5
[ 86.451724] rtl8192ce:rtl92ce_led_control():<10000-1> ledaction 5
[ 86.452711] rtl8192ce:rtl92ce_led_control():<10000-1> ledaction 5
[ 86.540275] rtl8192ce:rtl92ce_led_control():<10000-1> ledaction 5
[ 86.541418] rtl8192ce:rtl92ce_led_control():<10000-1> ledaction 5
[ 86.594256] rtl8192ce:rtl92ce_led_control():<10000-1> ledaction 5
[ 86.642615] rtl8192ce:rtl92ce_led_control():<10000-1> ledaction 5
After modprobe -r:
[ 86.913272] rtl8192ce:rtl92ce_led_control():<10000-1> ledaction 5
[ 86.967129] rtl8192ce:rtl92ce_led_control():<10000-1> ledaction 5
[ 86.968381] rtl8192ce:rtl92ce_led_control():<10000-1> ledaction 5
[ 87.025606] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
[ 87.025624] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
[ 87.044826] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
[ 87.044844] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
[ 87.044858] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 7
[ 87.044868] rtl8192ce:rtl92ce_sw_led_off():<0-0> LedAddr:4E ledpin=1
[ 87.045020] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 7
[ 87.045029] rtl8192ce:rtl92ce_sw_led_off():<0-0> LedAddr:4E ledpin=1
[ 88.970535] rtlwifi:rtl_ips_nic_off_wq_callback():<0-0> not station return
This one was harder to get because of the freeze when fwlps=1.
Anisse
[-- Attachment #2: lspci-rtl8192ce-no-up.txt --]
[-- Type: text/plain, Size: 3748 bytes --]
06:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. Device [10ec:8176] (rev 01)
Subsystem: Realtek Semiconductor Co., Ltd. Device [10ec:8212]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 3
Region 0: I/O ports at 3000 [size=256]
Region 2: Memory at f0200000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- FLReset-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP+ Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 01-91-81-fe-ff-4c-e0-00
00: ec 10 76 81 07 00 10 00 01 00 80 02 10 00 00 00
10: 01 30 00 00 00 00 00 00 04 00 20 f0 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 ec 10 12 82
30: 00 00 00 00 40 00 00 00 00 00 00 00 03 01 00 00
40: 01 50 c3 ff 08 00 00 00 00 00 00 00 00 00 00 00
50: 05 70 80 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 10 00 02 00 c0 8c 00 10 10 20 10 00 11 3c 07 00
80: 40 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 10 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: rtl8192ce: activation problem with rtl8188ce pci card
2012-09-05 17:38 ` Larry Finger
2012-09-05 18:01 ` Anisse Astier
@ 2012-09-05 18:14 ` Anisse Astier
2012-09-05 20:24 ` Larry Finger
1 sibling, 1 reply; 10+ messages in thread
From: Anisse Astier @ 2012-09-05 18:14 UTC (permalink / raw)
To: Larry Finger; +Cc: linux-wireless
On Wed, 05 Sep 2012 12:38:24 -0500, Larry Finger <Larry.Finger@lwfinger.net> wrote :
> I have two different revisions of the RTL8188CE card. The newer one, marked
> RTL8188CE-VL, gives the following lspci output:
>
> 06:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE
> 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01)
> Subsystem: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi
> Adapter [10ec:8176]
> Flags: bus master, fast devsel, latency 0, IRQ 20
> I/O ports at 4000 [size=256]
> Memory at f8000000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: [40] Power Management version 3
> Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
> Capabilities: [70] Express Endpoint, MSI 00
> Capabilities: [100] Advanced Error Reporting
> Capabilities: [140] Virtual Channel
> Capabilities: [160] Device Serial Number 01-91-81-fe-ff-4c-e0-00
> Kernel driver in use: rtl8192ce
>
> It certainly does not yield the rx descriptor problem. Please send the lspci
> output when the driver has not been loaded.
The subsystem ID is different on my wireless card (8212):
06:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01)
Subsystem: Realtek Semiconductor Co., Ltd. Device [10ec:8212]
Flags: bus master, fast devsel, latency 0, IRQ 3
I/O ports at 3000 [size=256]
Memory at f0200000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 01-91-81-fe-ff-4c-e0-00
This id is nowhere to be found in the rtlwifi driver. The only matches in
Google are my previous problem report (FWLPS freeze) and windows driver
listings.
Anisse
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: rtl8192ce: activation problem with rtl8188ce pci card
2012-09-05 18:14 ` Anisse Astier
@ 2012-09-05 20:24 ` Larry Finger
2012-09-06 8:01 ` Anisse Astier
2012-09-06 14:15 ` Anisse Astier
0 siblings, 2 replies; 10+ messages in thread
From: Larry Finger @ 2012-09-05 20:24 UTC (permalink / raw)
To: Anisse Astier; +Cc: linux-wireless, 李朝明
On 09/05/2012 01:14 PM, Anisse Astier wrote:
> On Wed, 05 Sep 2012 12:38:24 -0500, Larry Finger <Larry.Finger@lwfinger.net> wrote :
>
>> I have two different revisions of the RTL8188CE card. The newer one, marked
>> RTL8188CE-VL, gives the following lspci output:
>>
>> 06:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE
>> 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01)
>> Subsystem: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi
>> Adapter [10ec:8176]
>> Flags: bus master, fast devsel, latency 0, IRQ 20
>> I/O ports at 4000 [size=256]
>> Memory at f8000000 (64-bit, non-prefetchable) [size=16K]
>> Capabilities: [40] Power Management version 3
>> Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
>> Capabilities: [70] Express Endpoint, MSI 00
>> Capabilities: [100] Advanced Error Reporting
>> Capabilities: [140] Virtual Channel
>> Capabilities: [160] Device Serial Number 01-91-81-fe-ff-4c-e0-00
>> Kernel driver in use: rtl8192ce
>>
>> It certainly does not yield the rx descriptor problem. Please send the lspci
>> output when the driver has not been loaded.
>
> The subsystem ID is different on my wireless card (8212):
>
> 06:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01)
> Subsystem: Realtek Semiconductor Co., Ltd. Device [10ec:8212]
> Flags: bus master, fast devsel, latency 0, IRQ 3
> I/O ports at 3000 [size=256]
> Memory at f0200000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: [40] Power Management version 3
> Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
> Capabilities: [70] Express Endpoint, MSI 00
> Capabilities: [100] Advanced Error Reporting
> Capabilities: [140] Virtual Channel
> Capabilities: [160] Device Serial Number 01-91-81-fe-ff-4c-e0-00
>
> This id is nowhere to be found in the rtlwifi driver. The only matches in
> Google are my previous problem report (FWLPS freeze) and windows driver
> listings.
The ID that counts is the first one. I think the second is some kind of vendor code.
My other RTL8188CE gives the following output:
0e:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE
802.11b/g/n WiFi Adapter [10ec:8176] (rev 01)
Subsystem: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi
Adapter [10ec:8176]
Flags: bus master, fast devsel, latency 0, IRQ 20
I/O ports at 4000 [size=256]
Memory at f8000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 01-91-81-fe-ff-4c-e0-00
Kernel driver in use: rtl8192ce
Other than the MAC address, and the bus number, they have the same output.
Note, the RTL8188CE-VL does not work with wireless-next, but does with
wireless-testing with some patches applied. I will contact the Realtek software
team to ask questions about your card. I added my contact as a Cc here. In the
meantime, could you try the wireless-testing tree? If your card still does not
work, I will send you some patches to see what it takes.
Larry
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: rtl8192ce: activation problem with rtl8188ce pci card
2012-09-05 20:24 ` Larry Finger
@ 2012-09-06 8:01 ` Anisse Astier
2012-09-06 14:15 ` Anisse Astier
1 sibling, 0 replies; 10+ messages in thread
From: Anisse Astier @ 2012-09-06 8:01 UTC (permalink / raw)
To: Larry Finger; +Cc: linux-wireless, 李朝明
[-- Attachment #1: Type: text/plain, Size: 5280 bytes --]
Hi,
On Wed, 05 Sep 2012 15:24:40 -0500, Larry Finger <Larry.Finger@lwfinger.net> wrote :
> On 09/05/2012 01:14 PM, Anisse Astier wrote:
>
> The ID that counts is the first one. I think the second is some kind of vendor code.
Yes, it should be the id of the card instead of the chip. But it shows
that this module hasn't been lspci'd much in the wild.
>
> Note, the RTL8188CE-VL does not work with wireless-next, but does with
> wireless-testing with some patches applied. I will contact the Realtek software
> team to ask questions about your card. I added my contact as a Cc here. In the
> meantime, could you try the wireless-testing tree? If your card still does not
> work, I will send you some patches to see what it takes.
I have the same issue with wireless-testing. dmesg in attachment.
Logs:
[ 521.487043] cfg80211: Calling CRDA to update world regulatory domain
[ 521.590821] rtl8192ce: Using firmware rtlwifi/rtl8192cfw.bin
[ 521.632956] rtlwifi:rtl_fw_cb():<0-0> Firmware callback routine entered!
[ 521.697121] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 521.703862] rtlwifi: wireless switch is on
[ 521.761161] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 521.761267] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 521.761415] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 521.761564] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 521.761712] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 521.761860] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 521.762008] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 521.762157] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 521.762305] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:98053f15:10
[ 521.763460] rtl8192c_common:rtl92c_download_fw():<0-0> Firmware Version(49), Signature(0x88c1),Size(32)
[ 521.984907] rtl8192ce:rtl92ce_enable_hw_security_config():<0-0> PairwiseEncAlgorithm = 0 GroupEncAlgorithm = 0
[ 521.984924] rtl8192ce:rtl92ce_enable_hw_security_config():<0-0> The SECR-value cc
[ 522.093885] rtl8192c_common:rtl92c_dm_initialize_txpower_tracking_thermalmeter():<0-0> pMgntInfo->txpower_tracking = 1
[ 522.093901] rtlwifi:rtl_pci_start():<0-0> enable_interrupt OK
[ 522.093909] rtlwifi:rtl_pci_start():<0-0> OK
[ 522.097066] rtl8192c_common:rtl92c_dm_dynamic_bb_powersaving():<0-0> Not connected to any
[ 522.097080] rtl8192c_common:rtl92c_dm_dynamic_bb_powersaving():<0-0> AP Ext Port PWDB = 0x0
[ 522.097140] rtl8192c_common:rtl92c_dm_check_txpower_tracking_thermal_meter():<0-0> Trigger 92S Thermal Meter!!
[ 522.106799] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
[ 522.106806] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
[ 522.106843] rtlwifi:rtl_op_bss_info_changed():<0-0> BSS_CHANGED_ERP_PREAMBLE use short preamble:0
[ 522.106852] rtl8192ce:rtl92ce_set_hw_reg():<0-0> HW_VAR_SLOT_TIME 14
[ 522.107898] rtlwifi:rtl_op_config():<0-0> IEEE80211_CONF_CHANGE_LISTEN_INTERVAL
[ 522.108197] rtlwifi:rtl_op_config():<0-0> IEEE80211_CONF_CHANGE_RETRY_LIMITS 4
[ 522.119643] rtl8192c_common:rtl92c_phy_sw_chnl():<0-0> sw_chnl_inprogress false schdule workitem
[ 522.119650] rtl8192ce:rtl92ce_set_hw_reg():<0-0> HW_VAR_SLOT_TIME 14
[ 522.135385] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 522.185258] rtl8192ce:rtl92ce_led_control():<10000-1> ledaction 5
[ 522.208511] rtl8192ce:_rtl92ce_phy_set_rf_power_state():<0-0> IPS Set eRf nic disable
[ 522.209007] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
[ 522.209018] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
[ 523.421145] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 523.421161] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
[ 523.421891] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 523.421903] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
[ 523.425246] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 523.425261] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
[ 523.426638] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 523.426649] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
[ 523.426991] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 523.426995] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
[ 523.435796] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 523.435811] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
After removal:
[ 523.616579] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
[ 523.616596] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
[ 523.619524] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
[ 523.619538] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
[ 523.619549] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 7
[ 523.619559] rtl8192ce:rtl92ce_sw_led_off():<0-0> LedAddr:4E ledpin=1
[ 523.628275] rtl8192c_common:rtl92c_firmware_selfreset(): 8051 reset fail
[ 523.628296] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 7
[ 523.628305] rtl8192ce:rtl92ce_sw_led_off():<0-0> LedAddr:4E ledpin=1
Also I noticed that during the initialization phase (rtlwifi/pci.c)
RT_TRACE doesn't print anything.
Anisse
[-- Attachment #2: dmesg-rtl8192ce-no-up-wireless-testing.txt.gz --]
[-- Type: application/x-gzip, Size: 14023 bytes --]
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: rtl8192ce: activation problem with rtl8188ce pci card
2012-09-05 20:24 ` Larry Finger
2012-09-06 8:01 ` Anisse Astier
@ 2012-09-06 14:15 ` Anisse Astier
[not found] ` <5048D138.1080109@lwfinger.net>
1 sibling, 1 reply; 10+ messages in thread
From: Anisse Astier @ 2012-09-06 14:15 UTC (permalink / raw)
To: Larry Finger; +Cc: linux-wireless, 李朝明
On Wed, 05 Sep 2012 15:24:40 -0500, Larry Finger <Larry.Finger@lwfinger.net> wrote :
> Note, the RTL8188CE-VL does not work with wireless-next, but does with
> wireless-testing with some patches applied. I will contact the Realtek software
> team to ask questions about your card. I added my contact as a Cc here. In the
> meantime, could you try the wireless-testing tree? If your card still does not
> work, I will send you some patches to see what it takes.
What patch does wireless-testing have that aren't in wireless-next ? I
failed to find them.
Anisse
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2012-09-10 17:33 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-09-05 16:55 rtl8192ce: activation problem with rtl8188ce pci card Anisse Astier
2012-09-05 17:38 ` Larry Finger
2012-09-05 18:01 ` Anisse Astier
2012-09-05 18:14 ` Anisse Astier
2012-09-05 20:24 ` Larry Finger
2012-09-06 8:01 ` Anisse Astier
2012-09-06 14:15 ` Anisse Astier
[not found] ` <5048D138.1080109@lwfinger.net>
[not found] ` <20120906202710.30c4bc8a@destiny.ordissimo>
2012-09-06 19:04 ` Larry Finger
2012-09-07 8:44 ` Anisse Astier
2012-09-10 17:33 ` Anisse Astier
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.