Re: [PATCH] USB: EHCI: fix for leaking isochronous data

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 21.02.2013 19:54, Alan Stern wrote:
> I trust you won't mind if I put this on the public mailing list.  In
> general, problems of this sort should be discussed in public.  In
> addition to creating a permanent record in the various mailing list
> archives, it also gives other people a chance to learn about these
> problems and to chime in if they think of something I have overlooked.

This problem was already discussed on the kernel and mm mailing list. 
(see thread starting here: https://lkml.org/lkml/2012/11/6/408 )

Since this seems to be USB related now, of course it makes sense to 
discuss this problem on the usb mailing list.

> On Wed, 20 Feb 2013, Soeren Moch wrote:
>
>> Ok. I use 2 em2840-based usb sticks (em28xx driver) attached to a
>> Marvell Kirkwood-SoC with a orion-ehci usb controller. These usb sticks
>> stream dvb data (digital TV) employing isochronous usb transfers (user
>> application is vdr).
>>
>> Starting from linux-3.6 I see
>>     ERROR: 1024 KiB atomic DMA coherent pool is too small!
>> in the syslog after several 10 minutes (sometimes hours) of streaming
>> and then streaming stops.
>>
>> In linux-3.6 the memory management for the arm architecture was changed,
>> so that atomic coherent dma allocations are served from a special pool.
>> This pool gets exhausted. The only user of this pool (in my test) is
>> orion-ehci. Although I have only 10 URBs in flight (5 for each stick,
>> resubmitted in the completion handler), I have 256 atomic coherent
>> allocations (memory from the pool is allocated in pages) from orion-ehci
>> when I see this error. So I think there must be a memory leak (memory
>> allocated atomic somewhere below the usb_submit_urb call in em28xx-core.c).
>>
>> With other dvb sticks using usb bulk transfers I never see this error.
>>
>> Since you already found a memory leak in the ehci driver for isoc
>> transfers, I hoped you can help to solve this problem. If there are
>> additional questions, please ask. If there is something I can test, I
>> would be glad to do so.
>
> I guess the first thing is to get a dmesg log showing the problem.  You
> should build a kernel with CONFIG_USB_DEBUG enabled and post the part
> of the dmesg output starting from when you plug in the troublesome DVB
> stick.

Sorry for my late response. Now I built a kernel 3.8.0 with usb_debug 
enabled. See below for the syslog of device plug-in.

> It also might help to have a record of all the isochronous-related
> coherent allocations and deallocations done by the ehci-hcd driver.
> Are you comfortable making your own debugging changes?  The allocations
> are done by a call to dma_pool_alloc() in
> drivers/usb/host/ehci-sched.c:itd_urb_transaction() if the device runs
> at high speed and sitd_urb_transaction() if the device runs at full
> speed.  The deallocations are done by calls to dma_pool_free() in
> ehci-timer.c:end_free_itds().
>

I added a debug message to 
drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the 
allocation flags, see log below. For me this looks like nothing is 
allocated atomic here, so this function should not be the root cause of 
the dma coherent pool exhaustion. Are there other allocation functions 
which I could track?

Regards,
  Soeren Moch



Mar 10 15:21:05 guruvdr kernel: hub 1-1:1.0: state 7 ports 4 chg 0000 
evt 0008
Mar 10 15:21:05 guruvdr kernel: hub 1-1:1.0: port 3, status 0101, change 
0001, 12 Mb/s
Mar 10 15:21:05 guruvdr kernel: hub 1-1:1.0: debounce: port 3: total 
100ms stable 100ms status 0x101
Mar 10 15:21:05 guruvdr kernel: usb 1-1.3: new high-speed USB device 
number 6 using orion-ehci
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: default language 0x0409
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: udev 6, busnum 1, minor = 5
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: New USB device found, 
idVendor=0ccd, idProduct=00b2
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: New USB device strings: 
Mfr=3, Product=1, SerialNumber=2
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: Product: Cinergy HTC Stick
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: Manufacturer: TERRATEC
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: SerialNumber: 123456789ABCD
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: usb_probe_device
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: configuration #1 chosen from 
1 choice
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: adding 1-1.3:1.0 (config #1, 
interface 0)
Mar 10 15:21:06 guruvdr kernel: em28xx 1-1.3:1.0: usb_probe_interface
Mar 10 15:21:06 guruvdr kernel: em28xx 1-1.3:1.0: usb_probe_interface - 
got id
Mar 10 15:21:06 guruvdr kernel: em28xx: New device TERRATEC  Cinergy HTC 
Stick @ 480 Mbps (0ccd:00b2, interface 0, class 0)
Mar 10 15:21:06 guruvdr kernel: em28xx: Audio Vendor Class interface 0 found
Mar 10 15:21:06 guruvdr kernel: em28xx: Video interface 0 found
Mar 10 15:21:06 guruvdr kernel: em28xx: DVB interface 0 found
Mar 10 15:21:06 guruvdr kernel: em28xx #0: chip ID is em2884
Mar 10 15:21:06 guruvdr kernel: em28xx #0: Identified as Terratec 
Cinergy HTC Stick (card=82)
Mar 10 15:21:06 guruvdr kernel: em28xx #0: Config register raw data: 0x45
Mar 10 15:21:06 guruvdr kernel: em28xx #0: v4l2 driver version 0.1.3
Mar 10 15:21:06 guruvdr kernel: em28xx #0: V4L2 video device registered 
as video0
Mar 10 15:21:06 guruvdr kernel: usbcore: registered new interface driver 
em28xx
Mar 10 15:21:07 guruvdr kernel: drxk: status = 0x639260d9
Mar 10 15:21:07 guruvdr kernel: drxk: detected a drx-3926k, spin A3, 
xtal 20.250 MHz
Mar 10 15:21:09 guruvdr kernel: hub 1-1:1.0: state 7 ports 4 chg 0000 
evt 0010
Mar 10 15:21:09 guruvdr kernel: hub 1-1:1.0: port 4, status 0101, change 
0001, 12 Mb/s
Mar 10 15:21:09 guruvdr kernel: hub 1-1:1.0: debounce: port 4: total 
100ms stable 100ms status 0x101
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: new high-speed USB device 
number 7 using orion-ehci
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: default language 0x0409
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: udev 7, busnum 1, minor = 6
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: New USB device found, 
idVendor=2304, idProduct=0242
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: New USB device strings: 
Mfr=1, Product=2, SerialNumber=3
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: Product: PCTV 510e
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: Manufacturer: Pinnacle Systems
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: SerialNumber: 123456789012
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: usb_probe_device
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: configuration #1 chosen from 
1 choice
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: adding 1-1.4:1.0 (config #1, 
interface 0)
Mar 10 15:21:09 guruvdr kernel: em28xx 1-1.4:1.0: usb_probe_interface
Mar 10 15:21:09 guruvdr kernel: em28xx 1-1.4:1.0: usb_probe_interface - 
got id
Mar 10 15:21:09 guruvdr kernel: em28xx: New device Pinnacle Systems PCTV 
510e @ 480 Mbps (2304:0242, interface 0, class 0)
Mar 10 15:21:09 guruvdr kernel: em28xx: Audio Vendor Class interface 0 found
Mar 10 15:21:09 guruvdr kernel: em28xx: Video interface 0 found
Mar 10 15:21:09 guruvdr kernel: em28xx: DVB interface 0 found
Mar 10 15:21:09 guruvdr kernel: em28xx #1: chip ID is em2884
Mar 10 15:21:10 guruvdr kernel: em28xx #1: Identified as PCTV 
QuatroStick (510e) (card=85)
Mar 10 15:21:10 guruvdr kernel: em28xx #1: Config register raw data: 0x31
Mar 10 15:21:10 guruvdr kernel: em28xx #1: I2S Audio (5 sample rates)
Mar 10 15:21:10 guruvdr kernel: em28xx #1: No AC97 audio processor
Mar 10 15:21:10 guruvdr kernel: em28xx #1: v4l2 driver version 0.1.3
Mar 10 15:21:10 guruvdr kernel: em28xx #1: V4L2 video device registered 
as video1
Mar 10 15:21:10 guruvdr kernel: hub 1-1:1.0: state 7 ports 4 chg 0000 
evt 0010
Mar 10 15:21:11 guruvdr kernel: DRXK driver version 0.9.4300
Mar 10 15:21:11 guruvdr kernel: drxk: frontend initialized.
Mar 10 15:21:11 guruvdr kernel: tda18271 2-0060: creating new instance
Mar 10 15:21:11 guruvdr kernel: TDA18271HD/C2 detected @ 2-0060
Mar 10 15:21:12 guruvdr kernel: DVB: registering new adapter (em28xx #0)
Mar 10 15:21:12 guruvdr kernel: usb 1-1.3: DVB: registering adapter 2 
frontend 0 (DRXK DVB-C DVB-T)...
Mar 10 15:21:12 guruvdr kernel: em28xx #0: Successfully loaded em28xx-dvb
Mar 10 15:21:12 guruvdr kernel: Em28xx: Initialized (Em28xx dvb 
Extension) extension
Mar 10 15:21:12 guruvdr kernel: drxk: status = 0x039260d9
Mar 10 15:21:12 guruvdr kernel: drxk: detected a drx-3926k, spin A1, 
xtal 20.250 MHz
Mar 10 15:21:13 guruvdr kernel: DRXK driver version 0.9.4300
Mar 10 15:21:13 guruvdr kernel: drxk: frontend initialized.
Mar 10 15:21:13 guruvdr kernel: tda18271 3-0060: creating new instance
Mar 10 15:21:13 guruvdr kernel: TDA18271HD/C2 detected @ 3-0060
Mar 10 15:21:13 guruvdr kernel: DVB: registering new adapter (em28xx #1)
Mar 10 15:21:13 guruvdr kernel: usb 1-1.4: DVB: registering adapter 3 
frontend 0 (DRXK DVB-C DVB-T)...
Mar 10 15:21:13 guruvdr kernel: em28xx #1: Successfully loaded em28xx-dvb
[...]
Mar 10 18:55:05 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:05 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x80000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x80000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: ERROR: 1024 KiB atomic DMA coherent pool 
is too small!
Mar 10 18:55:06 guruvdr kernel: Please increase it with coherent_pool= 
kernel parameter!
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 10 18:55:07 guruvdr kernel: itd dma_pool_alloc flags: 0x80000093
Mar 10 18:55:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 10 18:55:07 guruvdr kernel: itd dma_pool_alloc flags: 0x80000093
Mar 10 18:55:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 10 18:55:08 guruvdr kernel: itd dma_pool_alloc flags: 0x80000093
Mar 10 18:55:08 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 10 18:55:13 guruvdr kernel: itd dma_pool_alloc flags: 0x80000013
Mar 10 18:55:13 guruvdr kernel: itd dma_pool_alloc flags: 0x20000013
Mar 10 18:55:13 guruvdr kernel: itd dma_pool_alloc flags: 0x20000013

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 21.02.2013 19:54, Alan Stern wrote:
> I trust you won't mind if I put this on the public mailing list.  In
> general, problems of this sort should be discussed in public.  In
> addition to creating a permanent record in the various mailing list
> archives, it also gives other people a chance to learn about these
> problems and to chime in if they think of something I have overlooked.

This problem was already discussed on the kernel and mm mailing list. 
(see thread starting here: https://lkml.org/lkml/2012/11/6/408 )

Since this seems to be USB related now, of course it makes sense to 
discuss this problem on the usb mailing list.

> On Wed, 20 Feb 2013, Soeren Moch wrote:
>
>> Ok. I use 2 em2840-based usb sticks (em28xx driver) attached to a
>> Marvell Kirkwood-SoC with a orion-ehci usb controller. These usb sticks
>> stream dvb data (digital TV) employing isochronous usb transfers (user
>> application is vdr).
>>
>> Starting from linux-3.6 I see
>>     ERROR: 1024 KiB atomic DMA coherent pool is too small!
>> in the syslog after several 10 minutes (sometimes hours) of streaming
>> and then streaming stops.
>>
>> In linux-3.6 the memory management for the arm architecture was changed,
>> so that atomic coherent dma allocations are served from a special pool.
>> This pool gets exhausted. The only user of this pool (in my test) is
>> orion-ehci. Although I have only 10 URBs in flight (5 for each stick,
>> resubmitted in the completion handler), I have 256 atomic coherent
>> allocations (memory from the pool is allocated in pages) from orion-ehci
>> when I see this error. So I think there must be a memory leak (memory
>> allocated atomic somewhere below the usb_submit_urb call in em28xx-core.c).
>>
>> With other dvb sticks using usb bulk transfers I never see this error.
>>
>> Since you already found a memory leak in the ehci driver for isoc
>> transfers, I hoped you can help to solve this problem. If there are
>> additional questions, please ask. If there is something I can test, I
>> would be glad to do so.
>
> I guess the first thing is to get a dmesg log showing the problem.  You
> should build a kernel with CONFIG_USB_DEBUG enabled and post the part
> of the dmesg output starting from when you plug in the troublesome DVB
> stick.

Sorry for my late response. Now I built a kernel 3.8.0 with usb_debug 
enabled. See below for the syslog of device plug-in.

> It also might help to have a record of all the isochronous-related
> coherent allocations and deallocations done by the ehci-hcd driver.
> Are you comfortable making your own debugging changes?  The allocations
> are done by a call to dma_pool_alloc() in
> drivers/usb/host/ehci-sched.c:itd_urb_transaction() if the device runs
> at high speed and sitd_urb_transaction() if the device runs at full
> speed.  The deallocations are done by calls to dma_pool_free() in
> ehci-timer.c:end_free_itds().
>

I added a debug message to 
drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the 
allocation flags, see log below. For me this looks like nothing is 
allocated atomic here, so this function should not be the root cause of 
the dma coherent pool exhaustion. Are there other allocation functions 
which I could track?

Regards,
  Soeren Moch



Mar 10 15:21:05 guruvdr kernel: hub 1-1:1.0: state 7 ports 4 chg 0000 
evt 0008
Mar 10 15:21:05 guruvdr kernel: hub 1-1:1.0: port 3, status 0101, change 
0001, 12 Mb/s
Mar 10 15:21:05 guruvdr kernel: hub 1-1:1.0: debounce: port 3: total 
100ms stable 100ms status 0x101
Mar 10 15:21:05 guruvdr kernel: usb 1-1.3: new high-speed USB device 
number 6 using orion-ehci
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: default language 0x0409
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: udev 6, busnum 1, minor = 5
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: New USB device found, 
idVendor=0ccd, idProduct=00b2
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: New USB device strings: 
Mfr=3, Product=1, SerialNumber=2
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: Product: Cinergy HTC Stick
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: Manufacturer: TERRATEC
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: SerialNumber: 123456789ABCD
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: usb_probe_device
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: configuration #1 chosen from 
1 choice
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: adding 1-1.3:1.0 (config #1, 
interface 0)
Mar 10 15:21:06 guruvdr kernel: em28xx 1-1.3:1.0: usb_probe_interface
Mar 10 15:21:06 guruvdr kernel: em28xx 1-1.3:1.0: usb_probe_interface - 
got id
Mar 10 15:21:06 guruvdr kernel: em28xx: New device TERRATEC  Cinergy HTC 
Stick @ 480 Mbps (0ccd:00b2, interface 0, class 0)
Mar 10 15:21:06 guruvdr kernel: em28xx: Audio Vendor Class interface 0 found
Mar 10 15:21:06 guruvdr kernel: em28xx: Video interface 0 found
Mar 10 15:21:06 guruvdr kernel: em28xx: DVB interface 0 found
Mar 10 15:21:06 guruvdr kernel: em28xx #0: chip ID is em2884
Mar 10 15:21:06 guruvdr kernel: em28xx #0: Identified as Terratec 
Cinergy HTC Stick (card=82)
Mar 10 15:21:06 guruvdr kernel: em28xx #0: Config register raw data: 0x45
Mar 10 15:21:06 guruvdr kernel: em28xx #0: v4l2 driver version 0.1.3
Mar 10 15:21:06 guruvdr kernel: em28xx #0: V4L2 video device registered 
as video0
Mar 10 15:21:06 guruvdr kernel: usbcore: registered new interface driver 
em28xx
Mar 10 15:21:07 guruvdr kernel: drxk: status = 0x639260d9
Mar 10 15:21:07 guruvdr kernel: drxk: detected a drx-3926k, spin A3, 
xtal 20.250 MHz
Mar 10 15:21:09 guruvdr kernel: hub 1-1:1.0: state 7 ports 4 chg 0000 
evt 0010
Mar 10 15:21:09 guruvdr kernel: hub 1-1:1.0: port 4, status 0101, change 
0001, 12 Mb/s
Mar 10 15:21:09 guruvdr kernel: hub 1-1:1.0: debounce: port 4: total 
100ms stable 100ms status 0x101
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: new high-speed USB device 
number 7 using orion-ehci
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: default language 0x0409
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: udev 7, busnum 1, minor = 6
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: New USB device found, 
idVendor=2304, idProduct=0242
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: New USB device strings: 
Mfr=1, Product=2, SerialNumber=3
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: Product: PCTV 510e
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: Manufacturer: Pinnacle Systems
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: SerialNumber: 123456789012
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: usb_probe_device
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: configuration #1 chosen from 
1 choice
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: adding 1-1.4:1.0 (config #1, 
interface 0)
Mar 10 15:21:09 guruvdr kernel: em28xx 1-1.4:1.0: usb_probe_interface
Mar 10 15:21:09 guruvdr kernel: em28xx 1-1.4:1.0: usb_probe_interface - 
got id
Mar 10 15:21:09 guruvdr kernel: em28xx: New device Pinnacle Systems PCTV 
510e @ 480 Mbps (2304:0242, interface 0, class 0)
Mar 10 15:21:09 guruvdr kernel: em28xx: Audio Vendor Class interface 0 found
Mar 10 15:21:09 guruvdr kernel: em28xx: Video interface 0 found
Mar 10 15:21:09 guruvdr kernel: em28xx: DVB interface 0 found
Mar 10 15:21:09 guruvdr kernel: em28xx #1: chip ID is em2884
Mar 10 15:21:10 guruvdr kernel: em28xx #1: Identified as PCTV 
QuatroStick (510e) (card=85)
Mar 10 15:21:10 guruvdr kernel: em28xx #1: Config register raw data: 0x31
Mar 10 15:21:10 guruvdr kernel: em28xx #1: I2S Audio (5 sample rates)
Mar 10 15:21:10 guruvdr kernel: em28xx #1: No AC97 audio processor
Mar 10 15:21:10 guruvdr kernel: em28xx #1: v4l2 driver version 0.1.3
Mar 10 15:21:10 guruvdr kernel: em28xx #1: V4L2 video device registered 
as video1
Mar 10 15:21:10 guruvdr kernel: hub 1-1:1.0: state 7 ports 4 chg 0000 
evt 0010
Mar 10 15:21:11 guruvdr kernel: DRXK driver version 0.9.4300
Mar 10 15:21:11 guruvdr kernel: drxk: frontend initialized.
Mar 10 15:21:11 guruvdr kernel: tda18271 2-0060: creating new instance
Mar 10 15:21:11 guruvdr kernel: TDA18271HD/C2 detected @ 2-0060
Mar 10 15:21:12 guruvdr kernel: DVB: registering new adapter (em28xx #0)
Mar 10 15:21:12 guruvdr kernel: usb 1-1.3: DVB: registering adapter 2 
frontend 0 (DRXK DVB-C DVB-T)...
Mar 10 15:21:12 guruvdr kernel: em28xx #0: Successfully loaded em28xx-dvb
Mar 10 15:21:12 guruvdr kernel: Em28xx: Initialized (Em28xx dvb 
Extension) extension
Mar 10 15:21:12 guruvdr kernel: drxk: status = 0x039260d9
Mar 10 15:21:12 guruvdr kernel: drxk: detected a drx-3926k, spin A1, 
xtal 20.250 MHz
Mar 10 15:21:13 guruvdr kernel: DRXK driver version 0.9.4300
Mar 10 15:21:13 guruvdr kernel: drxk: frontend initialized.
Mar 10 15:21:13 guruvdr kernel: tda18271 3-0060: creating new instance
Mar 10 15:21:13 guruvdr kernel: TDA18271HD/C2 detected @ 3-0060
Mar 10 15:21:13 guruvdr kernel: DVB: registering new adapter (em28xx #1)
Mar 10 15:21:13 guruvdr kernel: usb 1-1.4: DVB: registering adapter 3 
frontend 0 (DRXK DVB-C DVB-T)...
Mar 10 15:21:13 guruvdr kernel: em28xx #1: Successfully loaded em28xx-dvb
[...]
Mar 10 18:55:05 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:05 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x80000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x80000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: ERROR: 1024 KiB atomic DMA coherent pool 
is too small!
Mar 10 18:55:06 guruvdr kernel: Please increase it with coherent_pool= 
kernel parameter!
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 10 18:55:07 guruvdr kernel: itd dma_pool_alloc flags: 0x80000093
Mar 10 18:55:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 10 18:55:07 guruvdr kernel: itd dma_pool_alloc flags: 0x80000093
Mar 10 18:55:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 10 18:55:08 guruvdr kernel: itd dma_pool_alloc flags: 0x80000093
Mar 10 18:55:08 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 10 18:55:13 guruvdr kernel: itd dma_pool_alloc flags: 0x80000013
Mar 10 18:55:13 guruvdr kernel: itd dma_pool_alloc flags: 0x20000013
Mar 10 18:55:13 guruvdr kernel: itd dma_pool_alloc flags: 0x20000013

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 21.02.2013 19:54, Alan Stern wrote:
> I trust you won't mind if I put this on the public mailing list.  In
> general, problems of this sort should be discussed in public.  In
> addition to creating a permanent record in the various mailing list
> archives, it also gives other people a chance to learn about these
> problems and to chime in if they think of something I have overlooked.

This problem was already discussed on the kernel and mm mailing list. 
(see thread starting here: https://lkml.org/lkml/2012/11/6/408 )

Since this seems to be USB related now, of course it makes sense to 
discuss this problem on the usb mailing list.

> On Wed, 20 Feb 2013, Soeren Moch wrote:
>
>> Ok. I use 2 em2840-based usb sticks (em28xx driver) attached to a
>> Marvell Kirkwood-SoC with a orion-ehci usb controller. These usb sticks
>> stream dvb data (digital TV) employing isochronous usb transfers (user
>> application is vdr).
>>
>> Starting from linux-3.6 I see
>>     ERROR: 1024 KiB atomic DMA coherent pool is too small!
>> in the syslog after several 10 minutes (sometimes hours) of streaming
>> and then streaming stops.
>>
>> In linux-3.6 the memory management for the arm architecture was changed,
>> so that atomic coherent dma allocations are served from a special pool.
>> This pool gets exhausted. The only user of this pool (in my test) is
>> orion-ehci. Although I have only 10 URBs in flight (5 for each stick,
>> resubmitted in the completion handler), I have 256 atomic coherent
>> allocations (memory from the pool is allocated in pages) from orion-ehci
>> when I see this error. So I think there must be a memory leak (memory
>> allocated atomic somewhere below the usb_submit_urb call in em28xx-core.c).
>>
>> With other dvb sticks using usb bulk transfers I never see this error.
>>
>> Since you already found a memory leak in the ehci driver for isoc
>> transfers, I hoped you can help to solve this problem. If there are
>> additional questions, please ask. If there is something I can test, I
>> would be glad to do so.
>
> I guess the first thing is to get a dmesg log showing the problem.  You
> should build a kernel with CONFIG_USB_DEBUG enabled and post the part
> of the dmesg output starting from when you plug in the troublesome DVB
> stick.

Sorry for my late response. Now I built a kernel 3.8.0 with usb_debug 
enabled. See below for the syslog of device plug-in.

> It also might help to have a record of all the isochronous-related
> coherent allocations and deallocations done by the ehci-hcd driver.
> Are you comfortable making your own debugging changes?  The allocations
> are done by a call to dma_pool_alloc() in
> drivers/usb/host/ehci-sched.c:itd_urb_transaction() if the device runs
> at high speed and sitd_urb_transaction() if the device runs at full
> speed.  The deallocations are done by calls to dma_pool_free() in
> ehci-timer.c:end_free_itds().
>

I added a debug message to 
drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the 
allocation flags, see log below. For me this looks like nothing is 
allocated atomic here, so this function should not be the root cause of 
the dma coherent pool exhaustion. Are there other allocation functions 
which I could track?

Regards,
  Soeren Moch



Mar 10 15:21:05 guruvdr kernel: hub 1-1:1.0: state 7 ports 4 chg 0000 
evt 0008
Mar 10 15:21:05 guruvdr kernel: hub 1-1:1.0: port 3, status 0101, change 
0001, 12 Mb/s
Mar 10 15:21:05 guruvdr kernel: hub 1-1:1.0: debounce: port 3: total 
100ms stable 100ms status 0x101
Mar 10 15:21:05 guruvdr kernel: usb 1-1.3: new high-speed USB device 
number 6 using orion-ehci
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: default language 0x0409
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: udev 6, busnum 1, minor = 5
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: New USB device found, 
idVendor=0ccd, idProduct=00b2
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: New USB device strings: 
Mfr=3, Product=1, SerialNumber=2
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: Product: Cinergy HTC Stick
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: Manufacturer: TERRATEC
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: SerialNumber: 123456789ABCD
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: usb_probe_device
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: configuration #1 chosen from 
1 choice
Mar 10 15:21:06 guruvdr kernel: usb 1-1.3: adding 1-1.3:1.0 (config #1, 
interface 0)
Mar 10 15:21:06 guruvdr kernel: em28xx 1-1.3:1.0: usb_probe_interface
Mar 10 15:21:06 guruvdr kernel: em28xx 1-1.3:1.0: usb_probe_interface - 
got id
Mar 10 15:21:06 guruvdr kernel: em28xx: New device TERRATEC  Cinergy HTC 
Stick @ 480 Mbps (0ccd:00b2, interface 0, class 0)
Mar 10 15:21:06 guruvdr kernel: em28xx: Audio Vendor Class interface 0 found
Mar 10 15:21:06 guruvdr kernel: em28xx: Video interface 0 found
Mar 10 15:21:06 guruvdr kernel: em28xx: DVB interface 0 found
Mar 10 15:21:06 guruvdr kernel: em28xx #0: chip ID is em2884
Mar 10 15:21:06 guruvdr kernel: em28xx #0: Identified as Terratec 
Cinergy HTC Stick (card=82)
Mar 10 15:21:06 guruvdr kernel: em28xx #0: Config register raw data: 0x45
Mar 10 15:21:06 guruvdr kernel: em28xx #0: v4l2 driver version 0.1.3
Mar 10 15:21:06 guruvdr kernel: em28xx #0: V4L2 video device registered 
as video0
Mar 10 15:21:06 guruvdr kernel: usbcore: registered new interface driver 
em28xx
Mar 10 15:21:07 guruvdr kernel: drxk: status = 0x639260d9
Mar 10 15:21:07 guruvdr kernel: drxk: detected a drx-3926k, spin A3, 
xtal 20.250 MHz
Mar 10 15:21:09 guruvdr kernel: hub 1-1:1.0: state 7 ports 4 chg 0000 
evt 0010
Mar 10 15:21:09 guruvdr kernel: hub 1-1:1.0: port 4, status 0101, change 
0001, 12 Mb/s
Mar 10 15:21:09 guruvdr kernel: hub 1-1:1.0: debounce: port 4: total 
100ms stable 100ms status 0x101
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: new high-speed USB device 
number 7 using orion-ehci
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: default language 0x0409
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: udev 7, busnum 1, minor = 6
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: New USB device found, 
idVendor=2304, idProduct=0242
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: New USB device strings: 
Mfr=1, Product=2, SerialNumber=3
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: Product: PCTV 510e
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: Manufacturer: Pinnacle Systems
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: SerialNumber: 123456789012
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: usb_probe_device
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: configuration #1 chosen from 
1 choice
Mar 10 15:21:09 guruvdr kernel: usb 1-1.4: adding 1-1.4:1.0 (config #1, 
interface 0)
Mar 10 15:21:09 guruvdr kernel: em28xx 1-1.4:1.0: usb_probe_interface
Mar 10 15:21:09 guruvdr kernel: em28xx 1-1.4:1.0: usb_probe_interface - 
got id
Mar 10 15:21:09 guruvdr kernel: em28xx: New device Pinnacle Systems PCTV 
510e @ 480 Mbps (2304:0242, interface 0, class 0)
Mar 10 15:21:09 guruvdr kernel: em28xx: Audio Vendor Class interface 0 found
Mar 10 15:21:09 guruvdr kernel: em28xx: Video interface 0 found
Mar 10 15:21:09 guruvdr kernel: em28xx: DVB interface 0 found
Mar 10 15:21:09 guruvdr kernel: em28xx #1: chip ID is em2884
Mar 10 15:21:10 guruvdr kernel: em28xx #1: Identified as PCTV 
QuatroStick (510e) (card=85)
Mar 10 15:21:10 guruvdr kernel: em28xx #1: Config register raw data: 0x31
Mar 10 15:21:10 guruvdr kernel: em28xx #1: I2S Audio (5 sample rates)
Mar 10 15:21:10 guruvdr kernel: em28xx #1: No AC97 audio processor
Mar 10 15:21:10 guruvdr kernel: em28xx #1: v4l2 driver version 0.1.3
Mar 10 15:21:10 guruvdr kernel: em28xx #1: V4L2 video device registered 
as video1
Mar 10 15:21:10 guruvdr kernel: hub 1-1:1.0: state 7 ports 4 chg 0000 
evt 0010
Mar 10 15:21:11 guruvdr kernel: DRXK driver version 0.9.4300
Mar 10 15:21:11 guruvdr kernel: drxk: frontend initialized.
Mar 10 15:21:11 guruvdr kernel: tda18271 2-0060: creating new instance
Mar 10 15:21:11 guruvdr kernel: TDA18271HD/C2 detected @ 2-0060
Mar 10 15:21:12 guruvdr kernel: DVB: registering new adapter (em28xx #0)
Mar 10 15:21:12 guruvdr kernel: usb 1-1.3: DVB: registering adapter 2 
frontend 0 (DRXK DVB-C DVB-T)...
Mar 10 15:21:12 guruvdr kernel: em28xx #0: Successfully loaded em28xx-dvb
Mar 10 15:21:12 guruvdr kernel: Em28xx: Initialized (Em28xx dvb 
Extension) extension
Mar 10 15:21:12 guruvdr kernel: drxk: status = 0x039260d9
Mar 10 15:21:12 guruvdr kernel: drxk: detected a drx-3926k, spin A1, 
xtal 20.250 MHz
Mar 10 15:21:13 guruvdr kernel: DRXK driver version 0.9.4300
Mar 10 15:21:13 guruvdr kernel: drxk: frontend initialized.
Mar 10 15:21:13 guruvdr kernel: tda18271 3-0060: creating new instance
Mar 10 15:21:13 guruvdr kernel: TDA18271HD/C2 detected @ 3-0060
Mar 10 15:21:13 guruvdr kernel: DVB: registering new adapter (em28xx #1)
Mar 10 15:21:13 guruvdr kernel: usb 1-1.4: DVB: registering adapter 3 
frontend 0 (DRXK DVB-C DVB-T)...
Mar 10 15:21:13 guruvdr kernel: em28xx #1: Successfully loaded em28xx-dvb
[...]
Mar 10 18:55:05 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:05 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x80000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x80000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: ERROR: 1024 KiB atomic DMA coherent pool 
is too small!
Mar 10 18:55:06 guruvdr kernel: Please increase it with coherent_pool= 
kernel parameter!
Mar 10 18:55:06 guruvdr kernel: itd dma_pool_alloc flags: 0x20000093
Mar 10 18:55:06 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 10 18:55:07 guruvdr kernel: itd dma_pool_alloc flags: 0x80000093
Mar 10 18:55:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 10 18:55:07 guruvdr kernel: itd dma_pool_alloc flags: 0x80000093
Mar 10 18:55:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 10 18:55:08 guruvdr kernel: itd dma_pool_alloc flags: 0x80000093
Mar 10 18:55:08 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 10 18:55:13 guruvdr kernel: itd dma_pool_alloc flags: 0x80000013
Mar 10 18:55:13 guruvdr kernel: itd dma_pool_alloc flags: 0x20000013
Mar 10 18:55:13 guruvdr kernel: itd dma_pool_alloc flags: 0x20000013

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Sun, 10 Mar 2013, Soeren Moch wrote:

> > On Wed, 20 Feb 2013, Soeren Moch wrote:
> >
> >> Ok. I use 2 em2840-based usb sticks (em28xx driver) attached to a
> >> Marvell Kirkwood-SoC with a orion-ehci usb controller. These usb sticks
> >> stream dvb data (digital TV) employing isochronous usb transfers (user
> >> application is vdr).
> >>
> >> Starting from linux-3.6 I see
> >>     ERROR: 1024 KiB atomic DMA coherent pool is too small!
> >> in the syslog after several 10 minutes (sometimes hours) of streaming
> >> and then streaming stops.
> >>
> >> In linux-3.6 the memory management for the arm architecture was changed,
> >> so that atomic coherent dma allocations are served from a special pool.
> >> This pool gets exhausted. The only user of this pool (in my test) is
> >> orion-ehci. Although I have only 10 URBs in flight (5 for each stick,
> >> resubmitted in the completion handler), I have 256 atomic coherent
> >> allocations (memory from the pool is allocated in pages) from orion-ehci
> >> when I see this error. So I think there must be a memory leak (memory
> >> allocated atomic somewhere below the usb_submit_urb call in em28xx-core.c).
> >>
> >> With other dvb sticks using usb bulk transfers I never see this error.
> >>
> >> Since you already found a memory leak in the ehci driver for isoc
> >> transfers, I hoped you can help to solve this problem. If there are
> >> additional questions, please ask. If there is something I can test, I
> >> would be glad to do so.
> >
> > I guess the first thing is to get a dmesg log showing the problem.  You
> > should build a kernel with CONFIG_USB_DEBUG enabled and post the part
> > of the dmesg output starting from when you plug in the troublesome DVB
> > stick.
> 
> Sorry for my late response. Now I built a kernel 3.8.0 with usb_debug 
> enabled. See below for the syslog of device plug-in.
> 
> > It also might help to have a record of all the isochronous-related
> > coherent allocations and deallocations done by the ehci-hcd driver.
> > Are you comfortable making your own debugging changes?  The allocations
> > are done by a call to dma_pool_alloc() in
> > drivers/usb/host/ehci-sched.c:itd_urb_transaction() if the device runs
> > at high speed and sitd_urb_transaction() if the device runs at full
> > speed.  The deallocations are done by calls to dma_pool_free() in
> > ehci-timer.c:end_free_itds().
> >
> 
> I added a debug message to 
> drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the 
> allocation flags, see log below.

But it looks like you didn't add a message to end_free_itds(), so we
don't know when the memory gets deallocated.  And you didn't print out
the values of urb, num_itds, and i, or the value of itd (so we can
match up allocations against deallocations).

> For me this looks like nothing is 
> allocated atomic here, so this function should not be the root cause of 
> the dma coherent pool exhaustion.

I don't understand.  If non-atomic allocations can't exhaust the pool, 
why do we see these allocations fail?

> Are there other allocation functions 
> which I could track?

Yes, but they wouldn't be used for isochronous transfers.  See 
ehci_qtd_alloc(), ehci_qtd_free(), ehci_qh_alloc(), and qh_destroy() in 
ehci-mem.c, as well as some other one-time-only coherent allocations in 
that file.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Sun, 10 Mar 2013, Soeren Moch wrote:

> > On Wed, 20 Feb 2013, Soeren Moch wrote:
> >
> >> Ok. I use 2 em2840-based usb sticks (em28xx driver) attached to a
> >> Marvell Kirkwood-SoC with a orion-ehci usb controller. These usb sticks
> >> stream dvb data (digital TV) employing isochronous usb transfers (user
> >> application is vdr).
> >>
> >> Starting from linux-3.6 I see
> >>     ERROR: 1024 KiB atomic DMA coherent pool is too small!
> >> in the syslog after several 10 minutes (sometimes hours) of streaming
> >> and then streaming stops.
> >>
> >> In linux-3.6 the memory management for the arm architecture was changed,
> >> so that atomic coherent dma allocations are served from a special pool.
> >> This pool gets exhausted. The only user of this pool (in my test) is
> >> orion-ehci. Although I have only 10 URBs in flight (5 for each stick,
> >> resubmitted in the completion handler), I have 256 atomic coherent
> >> allocations (memory from the pool is allocated in pages) from orion-ehci
> >> when I see this error. So I think there must be a memory leak (memory
> >> allocated atomic somewhere below the usb_submit_urb call in em28xx-core.c).
> >>
> >> With other dvb sticks using usb bulk transfers I never see this error.
> >>
> >> Since you already found a memory leak in the ehci driver for isoc
> >> transfers, I hoped you can help to solve this problem. If there are
> >> additional questions, please ask. If there is something I can test, I
> >> would be glad to do so.
> >
> > I guess the first thing is to get a dmesg log showing the problem.  You
> > should build a kernel with CONFIG_USB_DEBUG enabled and post the part
> > of the dmesg output starting from when you plug in the troublesome DVB
> > stick.
> 
> Sorry for my late response. Now I built a kernel 3.8.0 with usb_debug 
> enabled. See below for the syslog of device plug-in.
> 
> > It also might help to have a record of all the isochronous-related
> > coherent allocations and deallocations done by the ehci-hcd driver.
> > Are you comfortable making your own debugging changes?  The allocations
> > are done by a call to dma_pool_alloc() in
> > drivers/usb/host/ehci-sched.c:itd_urb_transaction() if the device runs
> > at high speed and sitd_urb_transaction() if the device runs at full
> > speed.  The deallocations are done by calls to dma_pool_free() in
> > ehci-timer.c:end_free_itds().
> >
> 
> I added a debug message to 
> drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the 
> allocation flags, see log below.

But it looks like you didn't add a message to end_free_itds(), so we
don't know when the memory gets deallocated.  And you didn't print out
the values of urb, num_itds, and i, or the value of itd (so we can
match up allocations against deallocations).

> For me this looks like nothing is 
> allocated atomic here, so this function should not be the root cause of 
> the dma coherent pool exhaustion.

I don't understand.  If non-atomic allocations can't exhaust the pool, 
why do we see these allocations fail?

> Are there other allocation functions 
> which I could track?

Yes, but they wouldn't be used for isochronous transfers.  See 
ehci_qtd_alloc(), ehci_qtd_free(), ehci_qh_alloc(), and qh_destroy() in 
ehci-mem.c, as well as some other one-time-only coherent allocations in 
that file.

Alan Stern

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Sun, 10 Mar 2013, Soeren Moch wrote:

> > On Wed, 20 Feb 2013, Soeren Moch wrote:
> >
> >> Ok. I use 2 em2840-based usb sticks (em28xx driver) attached to a
> >> Marvell Kirkwood-SoC with a orion-ehci usb controller. These usb sticks
> >> stream dvb data (digital TV) employing isochronous usb transfers (user
> >> application is vdr).
> >>
> >> Starting from linux-3.6 I see
> >>     ERROR: 1024 KiB atomic DMA coherent pool is too small!
> >> in the syslog after several 10 minutes (sometimes hours) of streaming
> >> and then streaming stops.
> >>
> >> In linux-3.6 the memory management for the arm architecture was changed,
> >> so that atomic coherent dma allocations are served from a special pool.
> >> This pool gets exhausted. The only user of this pool (in my test) is
> >> orion-ehci. Although I have only 10 URBs in flight (5 for each stick,
> >> resubmitted in the completion handler), I have 256 atomic coherent
> >> allocations (memory from the pool is allocated in pages) from orion-ehci
> >> when I see this error. So I think there must be a memory leak (memory
> >> allocated atomic somewhere below the usb_submit_urb call in em28xx-core.c).
> >>
> >> With other dvb sticks using usb bulk transfers I never see this error.
> >>
> >> Since you already found a memory leak in the ehci driver for isoc
> >> transfers, I hoped you can help to solve this problem. If there are
> >> additional questions, please ask. If there is something I can test, I
> >> would be glad to do so.
> >
> > I guess the first thing is to get a dmesg log showing the problem.  You
> > should build a kernel with CONFIG_USB_DEBUG enabled and post the part
> > of the dmesg output starting from when you plug in the troublesome DVB
> > stick.
> 
> Sorry for my late response. Now I built a kernel 3.8.0 with usb_debug 
> enabled. See below for the syslog of device plug-in.
> 
> > It also might help to have a record of all the isochronous-related
> > coherent allocations and deallocations done by the ehci-hcd driver.
> > Are you comfortable making your own debugging changes?  The allocations
> > are done by a call to dma_pool_alloc() in
> > drivers/usb/host/ehci-sched.c:itd_urb_transaction() if the device runs
> > at high speed and sitd_urb_transaction() if the device runs at full
> > speed.  The deallocations are done by calls to dma_pool_free() in
> > ehci-timer.c:end_free_itds().
> >
> 
> I added a debug message to 
> drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the 
> allocation flags, see log below.

But it looks like you didn't add a message to end_free_itds(), so we
don't know when the memory gets deallocated.  And you didn't print out
the values of urb, num_itds, and i, or the value of itd (so we can
match up allocations against deallocations).

> For me this looks like nothing is 
> allocated atomic here, so this function should not be the root cause of 
> the dma coherent pool exhaustion.

I don't understand.  If non-atomic allocations can't exhaust the pool, 
why do we see these allocations fail?

> Are there other allocation functions 
> which I could track?

Yes, but they wouldn't be used for isochronous transfers.  See 
ehci_qtd_alloc(), ehci_qtd_free(), ehci_qh_alloc(), and qh_destroy() in 
ehci-mem.c, as well as some other one-time-only coherent allocations in 
that file.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 10.03.2013 21:59, Alan Stern wrote:
> On Sun, 10 Mar 2013, Soeren Moch wrote:
>>> On Wed, 20 Feb 2013, Soeren Moch wrote:
>>>
>>>> Ok. I use 2 em2840-based usb sticks (em28xx driver) attached to a
>>>> Marvell Kirkwood-SoC with a orion-ehci usb controller. These usb sticks
>>>> stream dvb data (digital TV) employing isochronous usb transfers (user
>>>> application is vdr).
>>>>
>>>> Starting from linux-3.6 I see
>>>>      ERROR: 1024 KiB atomic DMA coherent pool is too small!
>>>> in the syslog after several 10 minutes (sometimes hours) of streaming
>>>> and then streaming stops.
>>>>
>>>> In linux-3.6 the memory management for the arm architecture was changed,
>>>> so that atomic coherent dma allocations are served from a special pool.
>>>> This pool gets exhausted. The only user of this pool (in my test) is
>>>> orion-ehci. Although I have only 10 URBs in flight (5 for each stick,
>>>> resubmitted in the completion handler), I have 256 atomic coherent
>>>> allocations (memory from the pool is allocated in pages) from orion-ehci
>>>> when I see this error. So I think there must be a memory leak (memory
>>>> allocated atomic somewhere below the usb_submit_urb call in em28xx-core.c).
>>>>
>>>> With other dvb sticks using usb bulk transfers I never see this error.
>>>>
>>>> Since you already found a memory leak in the ehci driver for isoc
>>>> transfers, I hoped you can help to solve this problem. If there are
>>>> additional questions, please ask. If there is something I can test, I
>>>> would be glad to do so.
>>>
>>> I guess the first thing is to get a dmesg log showing the problem.  You
>>> should build a kernel with CONFIG_USB_DEBUG enabled and post the part
>>> of the dmesg output starting from when you plug in the troublesome DVB
>>> stick.
>>
>> Sorry for my late response. Now I built a kernel 3.8.0 with usb_debug
>> enabled. See below for the syslog of device plug-in.
>>
>>> It also might help to have a record of all the isochronous-related
>>> coherent allocations and deallocations done by the ehci-hcd driver.
>>> Are you comfortable making your own debugging changes?  The allocations
>>> are done by a call to dma_pool_alloc() in
>>> drivers/usb/host/ehci-sched.c:itd_urb_transaction() if the device runs
>>> at high speed and sitd_urb_transaction() if the device runs at full
>>> speed.  The deallocations are done by calls to dma_pool_free() in
>>> ehci-timer.c:end_free_itds().
>>>
>>
>> I added a debug message to
>> drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the
>> allocation flags, see log below.
>
> But it looks like you didn't add a message to end_free_itds(), so we
> don't know when the memory gets deallocated.  And you didn't print out
> the values of urb, num_itds, and i, or the value of itd (so we can
> match up allocations against deallocations).

OK, I will implement this more detailed logging. But with several 
allocations per second and runtime of several hours this will result in 
a very long logfile.

>> For me this looks like nothing is
>> allocated atomic here, so this function should not be the root cause of
>> the dma coherent pool exhaustion.
>
> I don't understand.  If non-atomic allocations can't exhaust the pool,
> why do we see these allocations fail?

Good point. Unfortunately I'm not familiar with the memory management 
details.

Arnd, can memory allocated with dma_pool_alloc() and gfp_flags 
0x20000093 or 0x80000093 come from the atomic dma coherent pool?

>> Are there other allocation functions
>> which I could track?
>
> Yes, but they wouldn't be used for isochronous transfers.  See
> ehci_qtd_alloc(), ehci_qtd_free(), ehci_qh_alloc(), and qh_destroy() in
> ehci-mem.c, as well as some other one-time-only coherent allocations in
> that file.
>
> Alan Stern
>
Soeren Moch

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 10.03.2013 21:59, Alan Stern wrote:
> On Sun, 10 Mar 2013, Soeren Moch wrote:
>>> On Wed, 20 Feb 2013, Soeren Moch wrote:
>>>
>>>> Ok. I use 2 em2840-based usb sticks (em28xx driver) attached to a
>>>> Marvell Kirkwood-SoC with a orion-ehci usb controller. These usb sticks
>>>> stream dvb data (digital TV) employing isochronous usb transfers (user
>>>> application is vdr).
>>>>
>>>> Starting from linux-3.6 I see
>>>>      ERROR: 1024 KiB atomic DMA coherent pool is too small!
>>>> in the syslog after several 10 minutes (sometimes hours) of streaming
>>>> and then streaming stops.
>>>>
>>>> In linux-3.6 the memory management for the arm architecture was changed,
>>>> so that atomic coherent dma allocations are served from a special pool.
>>>> This pool gets exhausted. The only user of this pool (in my test) is
>>>> orion-ehci. Although I have only 10 URBs in flight (5 for each stick,
>>>> resubmitted in the completion handler), I have 256 atomic coherent
>>>> allocations (memory from the pool is allocated in pages) from orion-ehci
>>>> when I see this error. So I think there must be a memory leak (memory
>>>> allocated atomic somewhere below the usb_submit_urb call in em28xx-core.c).
>>>>
>>>> With other dvb sticks using usb bulk transfers I never see this error.
>>>>
>>>> Since you already found a memory leak in the ehci driver for isoc
>>>> transfers, I hoped you can help to solve this problem. If there are
>>>> additional questions, please ask. If there is something I can test, I
>>>> would be glad to do so.
>>>
>>> I guess the first thing is to get a dmesg log showing the problem.  You
>>> should build a kernel with CONFIG_USB_DEBUG enabled and post the part
>>> of the dmesg output starting from when you plug in the troublesome DVB
>>> stick.
>>
>> Sorry for my late response. Now I built a kernel 3.8.0 with usb_debug
>> enabled. See below for the syslog of device plug-in.
>>
>>> It also might help to have a record of all the isochronous-related
>>> coherent allocations and deallocations done by the ehci-hcd driver.
>>> Are you comfortable making your own debugging changes?  The allocations
>>> are done by a call to dma_pool_alloc() in
>>> drivers/usb/host/ehci-sched.c:itd_urb_transaction() if the device runs
>>> at high speed and sitd_urb_transaction() if the device runs at full
>>> speed.  The deallocations are done by calls to dma_pool_free() in
>>> ehci-timer.c:end_free_itds().
>>>
>>
>> I added a debug message to
>> drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the
>> allocation flags, see log below.
>
> But it looks like you didn't add a message to end_free_itds(), so we
> don't know when the memory gets deallocated.  And you didn't print out
> the values of urb, num_itds, and i, or the value of itd (so we can
> match up allocations against deallocations).

OK, I will implement this more detailed logging. But with several 
allocations per second and runtime of several hours this will result in 
a very long logfile.

>> For me this looks like nothing is
>> allocated atomic here, so this function should not be the root cause of
>> the dma coherent pool exhaustion.
>
> I don't understand.  If non-atomic allocations can't exhaust the pool,
> why do we see these allocations fail?

Good point. Unfortunately I'm not familiar with the memory management 
details.

Arnd, can memory allocated with dma_pool_alloc() and gfp_flags 
0x20000093 or 0x80000093 come from the atomic dma coherent pool?

>> Are there other allocation functions
>> which I could track?
>
> Yes, but they wouldn't be used for isochronous transfers.  See
> ehci_qtd_alloc(), ehci_qtd_free(), ehci_qh_alloc(), and qh_destroy() in
> ehci-mem.c, as well as some other one-time-only coherent allocations in
> that file.
>
> Alan Stern
>
Soeren Moch

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 10.03.2013 21:59, Alan Stern wrote:
> On Sun, 10 Mar 2013, Soeren Moch wrote:
>>> On Wed, 20 Feb 2013, Soeren Moch wrote:
>>>
>>>> Ok. I use 2 em2840-based usb sticks (em28xx driver) attached to a
>>>> Marvell Kirkwood-SoC with a orion-ehci usb controller. These usb sticks
>>>> stream dvb data (digital TV) employing isochronous usb transfers (user
>>>> application is vdr).
>>>>
>>>> Starting from linux-3.6 I see
>>>>      ERROR: 1024 KiB atomic DMA coherent pool is too small!
>>>> in the syslog after several 10 minutes (sometimes hours) of streaming
>>>> and then streaming stops.
>>>>
>>>> In linux-3.6 the memory management for the arm architecture was changed,
>>>> so that atomic coherent dma allocations are served from a special pool.
>>>> This pool gets exhausted. The only user of this pool (in my test) is
>>>> orion-ehci. Although I have only 10 URBs in flight (5 for each stick,
>>>> resubmitted in the completion handler), I have 256 atomic coherent
>>>> allocations (memory from the pool is allocated in pages) from orion-ehci
>>>> when I see this error. So I think there must be a memory leak (memory
>>>> allocated atomic somewhere below the usb_submit_urb call in em28xx-core.c).
>>>>
>>>> With other dvb sticks using usb bulk transfers I never see this error.
>>>>
>>>> Since you already found a memory leak in the ehci driver for isoc
>>>> transfers, I hoped you can help to solve this problem. If there are
>>>> additional questions, please ask. If there is something I can test, I
>>>> would be glad to do so.
>>>
>>> I guess the first thing is to get a dmesg log showing the problem.  You
>>> should build a kernel with CONFIG_USB_DEBUG enabled and post the part
>>> of the dmesg output starting from when you plug in the troublesome DVB
>>> stick.
>>
>> Sorry for my late response. Now I built a kernel 3.8.0 with usb_debug
>> enabled. See below for the syslog of device plug-in.
>>
>>> It also might help to have a record of all the isochronous-related
>>> coherent allocations and deallocations done by the ehci-hcd driver.
>>> Are you comfortable making your own debugging changes?  The allocations
>>> are done by a call to dma_pool_alloc() in
>>> drivers/usb/host/ehci-sched.c:itd_urb_transaction() if the device runs
>>> at high speed and sitd_urb_transaction() if the device runs at full
>>> speed.  The deallocations are done by calls to dma_pool_free() in
>>> ehci-timer.c:end_free_itds().
>>>
>>
>> I added a debug message to
>> drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the
>> allocation flags, see log below.
>
> But it looks like you didn't add a message to end_free_itds(), so we
> don't know when the memory gets deallocated.  And you didn't print out
> the values of urb, num_itds, and i, or the value of itd (so we can
> match up allocations against deallocations).

OK, I will implement this more detailed logging. But with several 
allocations per second and runtime of several hours this will result in 
a very long logfile.

>> For me this looks like nothing is
>> allocated atomic here, so this function should not be the root cause of
>> the dma coherent pool exhaustion.
>
> I don't understand.  If non-atomic allocations can't exhaust the pool,
> why do we see these allocations fail?

Good point. Unfortunately I'm not familiar with the memory management 
details.

Arnd, can memory allocated with dma_pool_alloc() and gfp_flags 
0x20000093 or 0x80000093 come from the atomic dma coherent pool?

>> Are there other allocation functions
>> which I could track?
>
> Yes, but they wouldn't be used for isochronous transfers.  See
> ehci_qtd_alloc(), ehci_qtd_free(), ehci_qh_alloc(), and qh_destroy() in
> ehci-mem.c, as well as some other one-time-only coherent allocations in
> that file.
>
> Alan Stern
>
Soeren Moch

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 14.03.2013 19:48, Soeren Moch wrote:
> On 10.03.2013 21:59, Alan Stern wrote:
>> On Sun, 10 Mar 2013, Soeren Moch wrote:
>>>> On Wed, 20 Feb 2013, Soeren Moch wrote:
>>>>
>>>>> Ok. I use 2 em2840-based usb sticks (em28xx driver) attached to a
>>>>> Marvell Kirkwood-SoC with a orion-ehci usb controller. These usb
>>>>> sticks
>>>>> stream dvb data (digital TV) employing isochronous usb transfers (user
>>>>> application is vdr).
>>>>>
>>>>> Starting from linux-3.6 I see
>>>>>      ERROR: 1024 KiB atomic DMA coherent pool is too small!
>>>>> in the syslog after several 10 minutes (sometimes hours) of streaming
>>>>> and then streaming stops.
>>>>>
>>>>> In linux-3.6 the memory management for the arm architecture was
>>>>> changed,
>>>>> so that atomic coherent dma allocations are served from a special
>>>>> pool.
>>>>> This pool gets exhausted. The only user of this pool (in my test) is
>>>>> orion-ehci. Although I have only 10 URBs in flight (5 for each stick,
>>>>> resubmitted in the completion handler), I have 256 atomic coherent
>>>>> allocations (memory from the pool is allocated in pages) from
>>>>> orion-ehci
>>>>> when I see this error. So I think there must be a memory leak (memory
>>>>> allocated atomic somewhere below the usb_submit_urb call in
>>>>> em28xx-core.c).
>>>>>
>>>>> With other dvb sticks using usb bulk transfers I never see this error.
>>>>>
>>>>> Since you already found a memory leak in the ehci driver for isoc
>>>>> transfers, I hoped you can help to solve this problem. If there are
>>>>> additional questions, please ask. If there is something I can test, I
>>>>> would be glad to do so.
>>>>
>>>> I guess the first thing is to get a dmesg log showing the problem.  You
>>>> should build a kernel with CONFIG_USB_DEBUG enabled and post the part
>>>> of the dmesg output starting from when you plug in the troublesome DVB
>>>> stick.
>>>
>>> Sorry for my late response. Now I built a kernel 3.8.0 with usb_debug
>>> enabled. See below for the syslog of device plug-in.
>>>
>>>> It also might help to have a record of all the isochronous-related
>>>> coherent allocations and deallocations done by the ehci-hcd driver.
>>>> Are you comfortable making your own debugging changes?  The allocations
>>>> are done by a call to dma_pool_alloc() in
>>>> drivers/usb/host/ehci-sched.c:itd_urb_transaction() if the device runs
>>>> at high speed and sitd_urb_transaction() if the device runs at full
>>>> speed.  The deallocations are done by calls to dma_pool_free() in
>>>> ehci-timer.c:end_free_itds().
>>>>
>>>
>>> I added a debug message to
>>> drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the
>>> allocation flags, see log below.
>>
>> But it looks like you didn't add a message to end_free_itds(), so we
>> don't know when the memory gets deallocated.  And you didn't print out
>> the values of urb, num_itds, and i, or the value of itd (so we can
>> match up allocations against deallocations).
>
> OK, I will implement this more detailed logging. But with several
> allocations per second and runtime of several hours this will result in
> a very long logfile.
>
>>> For me this looks like nothing is
>>> allocated atomic here, so this function should not be the root cause of
>>> the dma coherent pool exhaustion.
>>
>> I don't understand.  If non-atomic allocations can't exhaust the pool,
>> why do we see these allocations fail?
>
> Good point. Unfortunately I'm not familiar with the memory management
> details.
>
> Arnd, can memory allocated with dma_pool_alloc() and gfp_flags
> 0x20000093 or 0x80000093 come from the atomic dma coherent pool?

Sorry, I logged the wrong flags. All allocations are GFP_ATOMIC (0x20) 
and therefore coming from the pool.

   Soeren

>>> Are there other allocation functions
>>> which I could track?
>>
>> Yes, but they wouldn't be used for isochronous transfers.  See
>> ehci_qtd_alloc(), ehci_qtd_free(), ehci_qh_alloc(), and qh_destroy() in
>> ehci-mem.c, as well as some other one-time-only coherent allocations in
>> that file.
>>
>> Alan Stern
>>
> Soeren Moch

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 14.03.2013 19:48, Soeren Moch wrote:
> On 10.03.2013 21:59, Alan Stern wrote:
>> On Sun, 10 Mar 2013, Soeren Moch wrote:
>>>> On Wed, 20 Feb 2013, Soeren Moch wrote:
>>>>
>>>>> Ok. I use 2 em2840-based usb sticks (em28xx driver) attached to a
>>>>> Marvell Kirkwood-SoC with a orion-ehci usb controller. These usb
>>>>> sticks
>>>>> stream dvb data (digital TV) employing isochronous usb transfers (user
>>>>> application is vdr).
>>>>>
>>>>> Starting from linux-3.6 I see
>>>>>      ERROR: 1024 KiB atomic DMA coherent pool is too small!
>>>>> in the syslog after several 10 minutes (sometimes hours) of streaming
>>>>> and then streaming stops.
>>>>>
>>>>> In linux-3.6 the memory management for the arm architecture was
>>>>> changed,
>>>>> so that atomic coherent dma allocations are served from a special
>>>>> pool.
>>>>> This pool gets exhausted. The only user of this pool (in my test) is
>>>>> orion-ehci. Although I have only 10 URBs in flight (5 for each stick,
>>>>> resubmitted in the completion handler), I have 256 atomic coherent
>>>>> allocations (memory from the pool is allocated in pages) from
>>>>> orion-ehci
>>>>> when I see this error. So I think there must be a memory leak (memory
>>>>> allocated atomic somewhere below the usb_submit_urb call in
>>>>> em28xx-core.c).
>>>>>
>>>>> With other dvb sticks using usb bulk transfers I never see this error.
>>>>>
>>>>> Since you already found a memory leak in the ehci driver for isoc
>>>>> transfers, I hoped you can help to solve this problem. If there are
>>>>> additional questions, please ask. If there is something I can test, I
>>>>> would be glad to do so.
>>>>
>>>> I guess the first thing is to get a dmesg log showing the problem.  You
>>>> should build a kernel with CONFIG_USB_DEBUG enabled and post the part
>>>> of the dmesg output starting from when you plug in the troublesome DVB
>>>> stick.
>>>
>>> Sorry for my late response. Now I built a kernel 3.8.0 with usb_debug
>>> enabled. See below for the syslog of device plug-in.
>>>
>>>> It also might help to have a record of all the isochronous-related
>>>> coherent allocations and deallocations done by the ehci-hcd driver.
>>>> Are you comfortable making your own debugging changes?  The allocations
>>>> are done by a call to dma_pool_alloc() in
>>>> drivers/usb/host/ehci-sched.c:itd_urb_transaction() if the device runs
>>>> at high speed and sitd_urb_transaction() if the device runs at full
>>>> speed.  The deallocations are done by calls to dma_pool_free() in
>>>> ehci-timer.c:end_free_itds().
>>>>
>>>
>>> I added a debug message to
>>> drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the
>>> allocation flags, see log below.
>>
>> But it looks like you didn't add a message to end_free_itds(), so we
>> don't know when the memory gets deallocated.  And you didn't print out
>> the values of urb, num_itds, and i, or the value of itd (so we can
>> match up allocations against deallocations).
>
> OK, I will implement this more detailed logging. But with several
> allocations per second and runtime of several hours this will result in
> a very long logfile.
>
>>> For me this looks like nothing is
>>> allocated atomic here, so this function should not be the root cause of
>>> the dma coherent pool exhaustion.
>>
>> I don't understand.  If non-atomic allocations can't exhaust the pool,
>> why do we see these allocations fail?
>
> Good point. Unfortunately I'm not familiar with the memory management
> details.
>
> Arnd, can memory allocated with dma_pool_alloc() and gfp_flags
> 0x20000093 or 0x80000093 come from the atomic dma coherent pool?

Sorry, I logged the wrong flags. All allocations are GFP_ATOMIC (0x20) 
and therefore coming from the pool.

   Soeren

>>> Are there other allocation functions
>>> which I could track?
>>
>> Yes, but they wouldn't be used for isochronous transfers.  See
>> ehci_qtd_alloc(), ehci_qtd_free(), ehci_qh_alloc(), and qh_destroy() in
>> ehci-mem.c, as well as some other one-time-only coherent allocations in
>> that file.
>>
>> Alan Stern
>>
> Soeren Moch

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 14.03.2013 19:48, Soeren Moch wrote:
> On 10.03.2013 21:59, Alan Stern wrote:
>> On Sun, 10 Mar 2013, Soeren Moch wrote:
>>>> On Wed, 20 Feb 2013, Soeren Moch wrote:
>>>>
>>>>> Ok. I use 2 em2840-based usb sticks (em28xx driver) attached to a
>>>>> Marvell Kirkwood-SoC with a orion-ehci usb controller. These usb
>>>>> sticks
>>>>> stream dvb data (digital TV) employing isochronous usb transfers (user
>>>>> application is vdr).
>>>>>
>>>>> Starting from linux-3.6 I see
>>>>>      ERROR: 1024 KiB atomic DMA coherent pool is too small!
>>>>> in the syslog after several 10 minutes (sometimes hours) of streaming
>>>>> and then streaming stops.
>>>>>
>>>>> In linux-3.6 the memory management for the arm architecture was
>>>>> changed,
>>>>> so that atomic coherent dma allocations are served from a special
>>>>> pool.
>>>>> This pool gets exhausted. The only user of this pool (in my test) is
>>>>> orion-ehci. Although I have only 10 URBs in flight (5 for each stick,
>>>>> resubmitted in the completion handler), I have 256 atomic coherent
>>>>> allocations (memory from the pool is allocated in pages) from
>>>>> orion-ehci
>>>>> when I see this error. So I think there must be a memory leak (memory
>>>>> allocated atomic somewhere below the usb_submit_urb call in
>>>>> em28xx-core.c).
>>>>>
>>>>> With other dvb sticks using usb bulk transfers I never see this error.
>>>>>
>>>>> Since you already found a memory leak in the ehci driver for isoc
>>>>> transfers, I hoped you can help to solve this problem. If there are
>>>>> additional questions, please ask. If there is something I can test, I
>>>>> would be glad to do so.
>>>>
>>>> I guess the first thing is to get a dmesg log showing the problem.  You
>>>> should build a kernel with CONFIG_USB_DEBUG enabled and post the part
>>>> of the dmesg output starting from when you plug in the troublesome DVB
>>>> stick.
>>>
>>> Sorry for my late response. Now I built a kernel 3.8.0 with usb_debug
>>> enabled. See below for the syslog of device plug-in.
>>>
>>>> It also might help to have a record of all the isochronous-related
>>>> coherent allocations and deallocations done by the ehci-hcd driver.
>>>> Are you comfortable making your own debugging changes?  The allocations
>>>> are done by a call to dma_pool_alloc() in
>>>> drivers/usb/host/ehci-sched.c:itd_urb_transaction() if the device runs
>>>> at high speed and sitd_urb_transaction() if the device runs at full
>>>> speed.  The deallocations are done by calls to dma_pool_free() in
>>>> ehci-timer.c:end_free_itds().
>>>>
>>>
>>> I added a debug message to
>>> drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the
>>> allocation flags, see log below.
>>
>> But it looks like you didn't add a message to end_free_itds(), so we
>> don't know when the memory gets deallocated.  And you didn't print out
>> the values of urb, num_itds, and i, or the value of itd (so we can
>> match up allocations against deallocations).
>
> OK, I will implement this more detailed logging. But with several
> allocations per second and runtime of several hours this will result in
> a very long logfile.
>
>>> For me this looks like nothing is
>>> allocated atomic here, so this function should not be the root cause of
>>> the dma coherent pool exhaustion.
>>
>> I don't understand.  If non-atomic allocations can't exhaust the pool,
>> why do we see these allocations fail?
>
> Good point. Unfortunately I'm not familiar with the memory management
> details.
>
> Arnd, can memory allocated with dma_pool_alloc() and gfp_flags
> 0x20000093 or 0x80000093 come from the atomic dma coherent pool?

Sorry, I logged the wrong flags. All allocations are GFP_ATOMIC (0x20) 
and therefore coming from the pool.

   Soeren

>>> Are there other allocation functions
>>> which I could track?
>>
>> Yes, but they wouldn't be used for isochronous transfers.  See
>> ehci_qtd_alloc(), ehci_qtd_free(), ehci_qh_alloc(), and qh_destroy() in
>> ehci-mem.c, as well as some other one-time-only coherent allocations in
>> that file.
>>
>> Alan Stern
>>
> Soeren Moch

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Thu, 14 Mar 2013, Soeren Moch wrote:

> >> I added a debug message to
> >> drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the
> >> allocation flags, see log below.
> >
> > But it looks like you didn't add a message to end_free_itds(), so we
> > don't know when the memory gets deallocated.  And you didn't print out
> > the values of urb, num_itds, and i, or the value of itd (so we can
> > match up allocations against deallocations).
> 
> OK, I will implement this more detailed logging. But with several 
> allocations per second and runtime of several hours this will result in 
> a very long logfile.

If the memory really is being leaked here in some sort of systematic
way, we may be able to see it in your debugging output after a few
seconds.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Thu, 14 Mar 2013, Soeren Moch wrote:

> >> I added a debug message to
> >> drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the
> >> allocation flags, see log below.
> >
> > But it looks like you didn't add a message to end_free_itds(), so we
> > don't know when the memory gets deallocated.  And you didn't print out
> > the values of urb, num_itds, and i, or the value of itd (so we can
> > match up allocations against deallocations).
> 
> OK, I will implement this more detailed logging. But with several 
> allocations per second and runtime of several hours this will result in 
> a very long logfile.

If the memory really is being leaked here in some sort of systematic
way, we may be able to see it in your debugging output after a few
seconds.

Alan Stern

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Thu, 14 Mar 2013, Soeren Moch wrote:

> >> I added a debug message to
> >> drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the
> >> allocation flags, see log below.
> >
> > But it looks like you didn't add a message to end_free_itds(), so we
> > don't know when the memory gets deallocated.  And you didn't print out
> > the values of urb, num_itds, and i, or the value of itd (so we can
> > match up allocations against deallocations).
> 
> OK, I will implement this more detailed logging. But with several 
> allocations per second and runtime of several hours this will result in 
> a very long logfile.

If the memory really is being leaked here in some sort of systematic
way, we may be able to see it in your debugging output after a few
seconds.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

[-- Attachment #1: Type: text/plain, Size: 955 bytes --]

On 14.03.2013 21:32, Alan Stern wrote:
> On Thu, 14 Mar 2013, Soeren Moch wrote:
>
>>>> I added a debug message to
>>>> drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the
>>>> allocation flags, see log below.
>>>
>>> But it looks like you didn't add a message to end_free_itds(), so we
>>> don't know when the memory gets deallocated.  And you didn't print out
>>> the values of urb, num_itds, and i, or the value of itd (so we can
>>> match up allocations against deallocations).
>>
>> OK, I will implement this more detailed logging. But with several
>> allocations per second and runtime of several hours this will result in
>> a very long logfile.
>
> If the memory really is being leaked here in some sort of systematic
> way, we may be able to see it in your debugging output after a few
> seconds.
>

OK, here are the first seconds of the log. But the buffer exhaustion 
usually occurs after several hours of runtime...

  Soeren Moch


[-- Attachment #2: syslog.gz --]
[-- Type: application/x-gzip, Size: 24383 bytes --]

[PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 14.03.2013 21:32, Alan Stern wrote:
> On Thu, 14 Mar 2013, Soeren Moch wrote:
>
>>>> I added a debug message to
>>>> drivers/usb/host/ehci-sched.c:itd_urb_transaction() to log the
>>>> allocation flags, see log below.
>>>
>>> But it looks like you didn't add a message to end_free_itds(), so we
>>> don't know when the memory gets deallocated.  And you didn't print out
>>> the values of urb, num_itds, and i, or the value of itd (so we can
>>> match up allocations against deallocations).
>>
>> OK, I will implement this more detailed logging. But with several
>> allocations per second and runtime of several hours this will result in
>> a very long logfile.
>
> If the memory really is being leaked here in some sort of systematic
> way, we may be able to see it in your debugging output after a few
> seconds.
>

OK, here are the first seconds of the log. But the buffer exhaustion 
usually occurs after several hours of runtime...

  Soeren Moch

-------------- next part --------------
A non-text attachment was scrubbed...
Name: syslog.gz
Type: application/x-gzip
Size: 24383 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20130314/e5ab1a24/attachment-0001.bin>

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Thu, 14 Mar 2013, Soeren Moch wrote:

> > If the memory really is being leaked here in some sort of systematic
> > way, we may be able to see it in your debugging output after a few
> > seconds.
> >
> 
> OK, here are the first seconds of the log. But the buffer exhaustion 
> usually occurs after several hours of runtime...

The log shows a 1-1 match between allocations and deallocations, except
for three excess allocations about 45 lines before the end.  I have no
idea what's up with those.  They may be an artifact arising from where
you stopped copying the log data.

There are as many as 400 iTDs being allocated before any are freed.  
That seems like a lot.  Are they all for the same isochronous endpoint?  
What's the endpoint's period?  How often are URBs submitted?

In general, there shouldn't be more than a couple of millisecond's
worth of iTDs allocated for any endpoint, depending on how many URBs 
are in the pipeline at any time.

Maybe a better way to go about this is, instead of printing out every
allocation and deallocation, to keep a running counter.  You could have
the driver print out the value of this counter every minute or so.  Any 
time the device isn't in use, the counter should be 0.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Thu, 14 Mar 2013, Soeren Moch wrote:

> > If the memory really is being leaked here in some sort of systematic
> > way, we may be able to see it in your debugging output after a few
> > seconds.
> >
> 
> OK, here are the first seconds of the log. But the buffer exhaustion 
> usually occurs after several hours of runtime...

The log shows a 1-1 match between allocations and deallocations, except
for three excess allocations about 45 lines before the end.  I have no
idea what's up with those.  They may be an artifact arising from where
you stopped copying the log data.

There are as many as 400 iTDs being allocated before any are freed.  
That seems like a lot.  Are they all for the same isochronous endpoint?  
What's the endpoint's period?  How often are URBs submitted?

In general, there shouldn't be more than a couple of millisecond's
worth of iTDs allocated for any endpoint, depending on how many URBs 
are in the pipeline at any time.

Maybe a better way to go about this is, instead of printing out every
allocation and deallocation, to keep a running counter.  You could have
the driver print out the value of this counter every minute or so.  Any 
time the device isn't in use, the counter should be 0.

Alan Stern

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Thu, 14 Mar 2013, Soeren Moch wrote:

> > If the memory really is being leaked here in some sort of systematic
> > way, we may be able to see it in your debugging output after a few
> > seconds.
> >
> 
> OK, here are the first seconds of the log. But the buffer exhaustion 
> usually occurs after several hours of runtime...

The log shows a 1-1 match between allocations and deallocations, except
for three excess allocations about 45 lines before the end.  I have no
idea what's up with those.  They may be an artifact arising from where
you stopped copying the log data.

There are as many as 400 iTDs being allocated before any are freed.  
That seems like a lot.  Are they all for the same isochronous endpoint?  
What's the endpoint's period?  How often are URBs submitted?

In general, there shouldn't be more than a couple of millisecond's
worth of iTDs allocated for any endpoint, depending on how many URBs 
are in the pipeline at any time.

Maybe a better way to go about this is, instead of printing out every
allocation and deallocation, to keep a running counter.  You could have
the driver print out the value of this counter every minute or so.  Any 
time the device isn't in use, the counter should be 0.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 14.03.2013 22:33, Alan Stern wrote:
> On Thu, 14 Mar 2013, Soeren Moch wrote:
>
>>> If the memory really is being leaked here in some sort of systematic
>>> way, we may be able to see it in your debugging output after a few
>>> seconds.
>>>
>>
>> OK, here are the first seconds of the log. But the buffer exhaustion
>> usually occurs after several hours of runtime...
>
> The log shows a 1-1 match between allocations and deallocations, except
> for three excess allocations about 45 lines before the end.  I have no
> idea what's up with those.  They may be an artifact arising from where
> you stopped copying the log data.
>
> There are as many as 400 iTDs being allocated before any are freed.
> That seems like a lot.  Are they all for the same isochronous endpoint?
> What's the endpoint's period?  How often are URBs submitted?

I use 2 dvb sticks, capturing digital TV. For each stick 5 URBs on a 
single endpoint are used, I think. I'm not sure, which endpoint in which 
alternateSetting is active. I attached the output of 'lsusb -v' for the 
sticks.
How can I track down the other information you need?

> In general, there shouldn't be more than a couple of millisecond's
> worth of iTDs allocated for any endpoint, depending on how many URBs
> are in the pipeline at any time.

Maybe the em28xx driver is not doing a good job here!?

  Soeren Moch

> Maybe a better way to go about this is, instead of printing out every
> allocation and deallocation, to keep a running counter.  You could have
> the driver print out the value of this counter every minute or so.  Any
> time the device isn't in use, the counter should be 0.
>
> Alan Stern



Bus 001 Device 005: ID 0ccd:00b2 TerraTec Electronic GmbH
Device Descriptor:
   bLength                18
   bDescriptorType         1
   bcdUSB               2.00
   bDeviceClass            0 (Defined at Interface level)
   bDeviceSubClass         0
   bDeviceProtocol         0
   bMaxPacketSize0        64
   idVendor           0x0ccd TerraTec Electronic GmbH
   idProduct          0x00b2
   bcdDevice            1.00
   iManufacturer           3 TERRATEC
   iProduct                1 Cinergy HTC Stick
   iSerial                 2 123456789ABCD
   bNumConfigurations      1
   Configuration Descriptor:
     bLength                 9
     bDescriptorType         2
     wTotalLength          305
     bNumInterfaces          1
     bConfigurationValue     1
     iConfiguration          0
     bmAttributes         0x80
       (Bus Powered)
     MaxPower              500mA
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       0
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       1
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       2
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0ad0  2x 720 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       3
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0c00  2x 1024 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       4
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1300  3x 768 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       5
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1380  3x 896 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       6
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x13c0  3x 960 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       7
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1400  3x 1024 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
Device Qualifier (for other device speed):
   bLength                10
   bDescriptorType         6
   bcdUSB               2.00
   bDeviceClass            0 (Defined at Interface level)
   bDeviceSubClass         0
   bDeviceProtocol         0
   bMaxPacketSize0        64
   bNumConfigurations      1
Device Status:     0x0000
   (Bus Powered)

Bus 001 Device 006: ID 2304:0242 Pinnacle Systems, Inc.
Device Descriptor:
   bLength                18
   bDescriptorType         1
   bcdUSB               2.00
   bDeviceClass            0 (Defined at Interface level)
   bDeviceSubClass         0
   bDeviceProtocol         0
   bMaxPacketSize0        64
   idVendor           0x2304 Pinnacle Systems, Inc.
   idProduct          0x0242
   bcdDevice            1.00
   iManufacturer           1 Pinnacle Systems
   iProduct                2 PCTV 510e
   iSerial                 3 123456789012
   bNumConfigurations      1
   Configuration Descriptor:
     bLength                 9
     bDescriptorType         2
     wTotalLength          305
     bNumInterfaces          1
     bConfigurationValue     1
     iConfiguration          0
     bmAttributes         0x80
       (Bus Powered)
     MaxPower              500mA
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       0
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       1
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       2
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0ad0  2x 720 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       3
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0c00  2x 1024 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       4
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1300  3x 768 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       5
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1380  3x 896 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       6
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x13c0  3x 960 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       7
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1400  3x 1024 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
Device Qualifier (for other device speed):
   bLength                10
   bDescriptorType         6
   bcdUSB               2.00
   bDeviceClass            0 (Defined at Interface level)
   bDeviceSubClass         0
   bDeviceProtocol         0
   bMaxPacketSize0        64
   bNumConfigurations      1
Device Status:     0x0000
   (Bus Powered)

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 14.03.2013 22:33, Alan Stern wrote:
> On Thu, 14 Mar 2013, Soeren Moch wrote:
>
>>> If the memory really is being leaked here in some sort of systematic
>>> way, we may be able to see it in your debugging output after a few
>>> seconds.
>>>
>>
>> OK, here are the first seconds of the log. But the buffer exhaustion
>> usually occurs after several hours of runtime...
>
> The log shows a 1-1 match between allocations and deallocations, except
> for three excess allocations about 45 lines before the end.  I have no
> idea what's up with those.  They may be an artifact arising from where
> you stopped copying the log data.
>
> There are as many as 400 iTDs being allocated before any are freed.
> That seems like a lot.  Are they all for the same isochronous endpoint?
> What's the endpoint's period?  How often are URBs submitted?

I use 2 dvb sticks, capturing digital TV. For each stick 5 URBs on a 
single endpoint are used, I think. I'm not sure, which endpoint in which 
alternateSetting is active. I attached the output of 'lsusb -v' for the 
sticks.
How can I track down the other information you need?

> In general, there shouldn't be more than a couple of millisecond's
> worth of iTDs allocated for any endpoint, depending on how many URBs
> are in the pipeline at any time.

Maybe the em28xx driver is not doing a good job here!?

  Soeren Moch

> Maybe a better way to go about this is, instead of printing out every
> allocation and deallocation, to keep a running counter.  You could have
> the driver print out the value of this counter every minute or so.  Any
> time the device isn't in use, the counter should be 0.
>
> Alan Stern



Bus 001 Device 005: ID 0ccd:00b2 TerraTec Electronic GmbH
Device Descriptor:
   bLength                18
   bDescriptorType         1
   bcdUSB               2.00
   bDeviceClass            0 (Defined at Interface level)
   bDeviceSubClass         0
   bDeviceProtocol         0
   bMaxPacketSize0        64
   idVendor           0x0ccd TerraTec Electronic GmbH
   idProduct          0x00b2
   bcdDevice            1.00
   iManufacturer           3 TERRATEC
   iProduct                1 Cinergy HTC Stick
   iSerial                 2 123456789ABCD
   bNumConfigurations      1
   Configuration Descriptor:
     bLength                 9
     bDescriptorType         2
     wTotalLength          305
     bNumInterfaces          1
     bConfigurationValue     1
     iConfiguration          0
     bmAttributes         0x80
       (Bus Powered)
     MaxPower              500mA
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       0
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       1
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       2
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0ad0  2x 720 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       3
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0c00  2x 1024 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       4
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1300  3x 768 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       5
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1380  3x 896 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       6
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x13c0  3x 960 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       7
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1400  3x 1024 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
Device Qualifier (for other device speed):
   bLength                10
   bDescriptorType         6
   bcdUSB               2.00
   bDeviceClass            0 (Defined at Interface level)
   bDeviceSubClass         0
   bDeviceProtocol         0
   bMaxPacketSize0        64
   bNumConfigurations      1
Device Status:     0x0000
   (Bus Powered)

Bus 001 Device 006: ID 2304:0242 Pinnacle Systems, Inc.
Device Descriptor:
   bLength                18
   bDescriptorType         1
   bcdUSB               2.00
   bDeviceClass            0 (Defined at Interface level)
   bDeviceSubClass         0
   bDeviceProtocol         0
   bMaxPacketSize0        64
   idVendor           0x2304 Pinnacle Systems, Inc.
   idProduct          0x0242
   bcdDevice            1.00
   iManufacturer           1 Pinnacle Systems
   iProduct                2 PCTV 510e
   iSerial                 3 123456789012
   bNumConfigurations      1
   Configuration Descriptor:
     bLength                 9
     bDescriptorType         2
     wTotalLength          305
     bNumInterfaces          1
     bConfigurationValue     1
     iConfiguration          0
     bmAttributes         0x80
       (Bus Powered)
     MaxPower              500mA
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       0
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       1
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       2
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0ad0  2x 720 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       3
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0c00  2x 1024 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       4
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1300  3x 768 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       5
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1380  3x 896 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       6
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x13c0  3x 960 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       7
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1400  3x 1024 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
Device Qualifier (for other device speed):
   bLength                10
   bDescriptorType         6
   bcdUSB               2.00
   bDeviceClass            0 (Defined at Interface level)
   bDeviceSubClass         0
   bDeviceProtocol         0
   bMaxPacketSize0        64
   bNumConfigurations      1
Device Status:     0x0000
   (Bus Powered)

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 14.03.2013 22:33, Alan Stern wrote:
> On Thu, 14 Mar 2013, Soeren Moch wrote:
>
>>> If the memory really is being leaked here in some sort of systematic
>>> way, we may be able to see it in your debugging output after a few
>>> seconds.
>>>
>>
>> OK, here are the first seconds of the log. But the buffer exhaustion
>> usually occurs after several hours of runtime...
>
> The log shows a 1-1 match between allocations and deallocations, except
> for three excess allocations about 45 lines before the end.  I have no
> idea what's up with those.  They may be an artifact arising from where
> you stopped copying the log data.
>
> There are as many as 400 iTDs being allocated before any are freed.
> That seems like a lot.  Are they all for the same isochronous endpoint?
> What's the endpoint's period?  How often are URBs submitted?

I use 2 dvb sticks, capturing digital TV. For each stick 5 URBs on a 
single endpoint are used, I think. I'm not sure, which endpoint in which 
alternateSetting is active. I attached the output of 'lsusb -v' for the 
sticks.
How can I track down the other information you need?

> In general, there shouldn't be more than a couple of millisecond's
> worth of iTDs allocated for any endpoint, depending on how many URBs
> are in the pipeline at any time.

Maybe the em28xx driver is not doing a good job here!?

  Soeren Moch

> Maybe a better way to go about this is, instead of printing out every
> allocation and deallocation, to keep a running counter.  You could have
> the driver print out the value of this counter every minute or so.  Any
> time the device isn't in use, the counter should be 0.
>
> Alan Stern



Bus 001 Device 005: ID 0ccd:00b2 TerraTec Electronic GmbH
Device Descriptor:
   bLength                18
   bDescriptorType         1
   bcdUSB               2.00
   bDeviceClass            0 (Defined at Interface level)
   bDeviceSubClass         0
   bDeviceProtocol         0
   bMaxPacketSize0        64
   idVendor           0x0ccd TerraTec Electronic GmbH
   idProduct          0x00b2
   bcdDevice            1.00
   iManufacturer           3 TERRATEC
   iProduct                1 Cinergy HTC Stick
   iSerial                 2 123456789ABCD
   bNumConfigurations      1
   Configuration Descriptor:
     bLength                 9
     bDescriptorType         2
     wTotalLength          305
     bNumInterfaces          1
     bConfigurationValue     1
     iConfiguration          0
     bmAttributes         0x80
       (Bus Powered)
     MaxPower              500mA
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       0
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       1
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       2
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0ad0  2x 720 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       3
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0c00  2x 1024 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       4
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1300  3x 768 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       5
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1380  3x 896 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       6
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x13c0  3x 960 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       7
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1400  3x 1024 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
Device Qualifier (for other device speed):
   bLength                10
   bDescriptorType         6
   bcdUSB               2.00
   bDeviceClass            0 (Defined at Interface level)
   bDeviceSubClass         0
   bDeviceProtocol         0
   bMaxPacketSize0        64
   bNumConfigurations      1
Device Status:     0x0000
   (Bus Powered)

Bus 001 Device 006: ID 2304:0242 Pinnacle Systems, Inc.
Device Descriptor:
   bLength                18
   bDescriptorType         1
   bcdUSB               2.00
   bDeviceClass            0 (Defined at Interface level)
   bDeviceSubClass         0
   bDeviceProtocol         0
   bMaxPacketSize0        64
   idVendor           0x2304 Pinnacle Systems, Inc.
   idProduct          0x0242
   bcdDevice            1.00
   iManufacturer           1 Pinnacle Systems
   iProduct                2 PCTV 510e
   iSerial                 3 123456789012
   bNumConfigurations      1
   Configuration Descriptor:
     bLength                 9
     bDescriptorType         2
     wTotalLength          305
     bNumInterfaces          1
     bConfigurationValue     1
     iConfiguration          0
     bmAttributes         0x80
       (Bus Powered)
     MaxPower              500mA
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       0
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       1
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0000  1x 0 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       2
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0ad0  2x 720 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       3
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0c00  2x 1024 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       4
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1300  3x 768 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       5
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1380  3x 896 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       6
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x13c0  3x 960 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
     Interface Descriptor:
       bLength                 9
       bDescriptorType         4
       bInterfaceNumber        0
       bAlternateSetting       7
       bNumEndpoints           4
       bInterfaceClass       255 Vendor Specific Class
       bInterfaceSubClass      0
       bInterfaceProtocol    255
       iInterface              0
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x81  EP 1 IN
         bmAttributes            3
           Transfer Type            Interrupt
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x0001  1x 1 bytes
         bInterval              11
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x82  EP 2 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x1400  3x 1024 bytes
         bInterval               1
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x83  EP 3 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x00c4  1x 196 bytes
         bInterval               4
       Endpoint Descriptor:
         bLength                 7
         bDescriptorType         5
         bEndpointAddress     0x84  EP 4 IN
         bmAttributes            1
           Transfer Type            Isochronous
           Synch Type               None
           Usage Type               Data
         wMaxPacketSize     0x03ac  1x 940 bytes
         bInterval               1
Device Qualifier (for other device speed):
   bLength                10
   bDescriptorType         6
   bcdUSB               2.00
   bDeviceClass            0 (Defined at Interface level)
   bDeviceSubClass         0
   bDeviceProtocol         0
   bMaxPacketSize0        64
   bNumConfigurations      1
Device Status:     0x0000
   (Bus Powered)

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Fri, 15 Mar 2013, Soeren Moch wrote:

> > The log shows a 1-1 match between allocations and deallocations, except
> > for three excess allocations about 45 lines before the end.  I have no
> > idea what's up with those.  They may be an artifact arising from where
> > you stopped copying the log data.
> >
> > There are as many as 400 iTDs being allocated before any are freed.
> > That seems like a lot.  Are they all for the same isochronous endpoint?
> > What's the endpoint's period?  How often are URBs submitted?
> 
> I use 2 dvb sticks, capturing digital TV. For each stick 5 URBs on a 
> single endpoint are used, I think. I'm not sure, which endpoint in which 
> alternateSetting is active. I attached the output of 'lsusb -v' for the 
> sticks.
> How can I track down the other information you need?

Use usbmon (see Documentation/usb/usbmon.txt).

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Fri, 15 Mar 2013, Soeren Moch wrote:

> > The log shows a 1-1 match between allocations and deallocations, except
> > for three excess allocations about 45 lines before the end.  I have no
> > idea what's up with those.  They may be an artifact arising from where
> > you stopped copying the log data.
> >
> > There are as many as 400 iTDs being allocated before any are freed.
> > That seems like a lot.  Are they all for the same isochronous endpoint?
> > What's the endpoint's period?  How often are URBs submitted?
> 
> I use 2 dvb sticks, capturing digital TV. For each stick 5 URBs on a 
> single endpoint are used, I think. I'm not sure, which endpoint in which 
> alternateSetting is active. I attached the output of 'lsusb -v' for the 
> sticks.
> How can I track down the other information you need?

Use usbmon (see Documentation/usb/usbmon.txt).

Alan Stern

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Fri, 15 Mar 2013, Soeren Moch wrote:

> > The log shows a 1-1 match between allocations and deallocations, except
> > for three excess allocations about 45 lines before the end.  I have no
> > idea what's up with those.  They may be an artifact arising from where
> > you stopped copying the log data.
> >
> > There are as many as 400 iTDs being allocated before any are freed.
> > That seems like a lot.  Are they all for the same isochronous endpoint?
> > What's the endpoint's period?  How often are URBs submitted?
> 
> I use 2 dvb sticks, capturing digital TV. For each stick 5 URBs on a 
> single endpoint are used, I think. I'm not sure, which endpoint in which 
> alternateSetting is active. I attached the output of 'lsusb -v' for the 
> sticks.
> How can I track down the other information you need?

Use usbmon (see Documentation/usb/usbmon.txt).

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 14.03.2013 22:33, Alan Stern wrote:
> Maybe a better way to go about this is, instead of printing out every
> allocation and deallocation, to keep a running counter.  You could have
> the driver print out the value of this counter every minute or so.  Any
> time the device isn't in use, the counter should be 0.

I implemented the counter. The max value is sampled at the beginning of 
end_free_itds(), the current counter value is sampled at the end of this 
function. Counter values w/o a max number are from the error path in 
itd_urb_transaction().
The number of allocated iTDs can grow to higher values (why?), but 
normally the iTDs are freed during normal operation. Due to some reason 
the number of iTDs suddenly increases until coherent pool exhaustion. 
There is no permanent memory leak, all iTDs are released when the user 
application ends. But imho several thousands of iTDs cannot be the 
intended behavior...

   Soeren


Mar 16 01:12:52 guruvdr kernel: itd_counter:42 (max:174)
Mar 16 01:12:52 guruvdr kernel: itd_counter:0 (max:174)
Mar 16 01:13:13 guruvdr kernel: itd_counter:42 (max:174)
Mar 16 01:13:13 guruvdr kernel: itd_counter:0 (max:174)
Mar 16 01:13:34 guruvdr kernel: itd_counter:87 (max:174)
Mar 16 01:13:34 guruvdr kernel: itd_counter:0 (max:174)
Mar 16 01:13:55 guruvdr kernel: itd_counter:42 (max:426)
Mar 16 01:13:55 guruvdr kernel: itd_counter:0 (max:426)
Mar 16 01:15:14 guruvdr kernel: itd_counter:249 (max:1441)
Mar 16 01:15:14 guruvdr kernel: itd_counter:0 (max:1441)
[...]
Mar 16 02:03:33 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:04:15 guruvdr kernel: itd_counter:150 (max:1441)
Mar 16 02:04:15 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:04:36 guruvdr kernel: itd_counter:42 (max:1441)
Mar 16 02:04:36 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:04:57 guruvdr kernel: itd_counter:42 (max:1441)
Mar 16 02:04:57 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:05:18 guruvdr kernel: itd_counter:42 (max:1441)
Mar 16 02:05:18 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:05:39 guruvdr kernel: itd_counter:42 (max:1441)
Mar 16 02:05:39 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:06:43 guruvdr kernel: itd_counter:254 (max:1441)
Mar 16 02:07:44 guruvdr kernel: itd_counter:968 (max:1469)
Mar 16 02:08:04 guruvdr kernel: itd_counter:1192 (max:1469)
Mar 16 02:08:46 guruvdr kernel: itd_counter:1812 (max:1854)
Mar 16 02:09:07 guruvdr kernel: itd_counter:2117 (max:2159)
Mar 16 02:09:28 guruvdr kernel: itd_counter:2482 (max:2524)
Mar 16 02:09:49 guruvdr kernel: itd_counter:2791 (max:2833)
Mar 16 02:10:10 guruvdr kernel: itd_counter:3088 (max:3409)
Mar 16 02:10:31 guruvdr kernel: itd_counter:3402 (max:3444)
Mar 16 02:10:52 guruvdr kernel: itd_counter:3689 (max:3731)
Mar 16 02:11:13 guruvdr kernel: itd_counter:3950 (max:4073)
Mar 16 02:11:34 guruvdr kernel: itd_counter:4264 (max:4306)
Mar 16 02:11:55 guruvdr kernel: itd_counter:4525 (max:4567)
Mar 16 02:12:16 guruvdr kernel: itd_counter:4803 (max:4845)
Mar 16 02:12:37 guruvdr kernel: itd_counter:5028 (max:5070)
Mar 16 02:13:19 guruvdr kernel: itd_counter:5549 (max:5843)
Mar 16 02:13:40 guruvdr kernel: itd_counter:5836 (max:5878)
Mar 16 02:14:01 guruvdr kernel: itd_counter:6133 (max:6238)
Mar 16 02:14:06 guruvdr kernel: ERROR: 1024 KiB atomic DMA coherent pool 
is too small!
Mar 16 02:14:06 guruvdr kernel: Please increase it with coherent_pool= 
kernel parameter!
Mar 16 02:14:06 guruvdr kernel: itd_counter:6275
Mar 16 02:14:06 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:06 guruvdr kernel: itd_counter:6275
Mar 16 02:14:06 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:06 guruvdr kernel: itd_counter:6275
Mar 16 02:14:06 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:06 guruvdr kernel: itd_counter:6275
Mar 16 02:14:06 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:07 guruvdr kernel: itd_counter:6275
Mar 16 02:14:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:07 guruvdr kernel: itd_counter:6275
Mar 16 02:14:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:07 guruvdr kernel: itd_counter:6275
Mar 16 02:14:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:07 guruvdr kernel: itd_counter:6275
Mar 16 02:14:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:08 guruvdr kernel: itd_counter:6275
Mar 16 02:14:08 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:08 guruvdr kernel: itd_counter:78 (max:6275)
Mar 16 02:14:22 guruvdr kernel: itd_counter:0 (max:6275)

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 14.03.2013 22:33, Alan Stern wrote:
> Maybe a better way to go about this is, instead of printing out every
> allocation and deallocation, to keep a running counter.  You could have
> the driver print out the value of this counter every minute or so.  Any
> time the device isn't in use, the counter should be 0.

I implemented the counter. The max value is sampled at the beginning of 
end_free_itds(), the current counter value is sampled at the end of this 
function. Counter values w/o a max number are from the error path in 
itd_urb_transaction().
The number of allocated iTDs can grow to higher values (why?), but 
normally the iTDs are freed during normal operation. Due to some reason 
the number of iTDs suddenly increases until coherent pool exhaustion. 
There is no permanent memory leak, all iTDs are released when the user 
application ends. But imho several thousands of iTDs cannot be the 
intended behavior...

   Soeren


Mar 16 01:12:52 guruvdr kernel: itd_counter:42 (max:174)
Mar 16 01:12:52 guruvdr kernel: itd_counter:0 (max:174)
Mar 16 01:13:13 guruvdr kernel: itd_counter:42 (max:174)
Mar 16 01:13:13 guruvdr kernel: itd_counter:0 (max:174)
Mar 16 01:13:34 guruvdr kernel: itd_counter:87 (max:174)
Mar 16 01:13:34 guruvdr kernel: itd_counter:0 (max:174)
Mar 16 01:13:55 guruvdr kernel: itd_counter:42 (max:426)
Mar 16 01:13:55 guruvdr kernel: itd_counter:0 (max:426)
Mar 16 01:15:14 guruvdr kernel: itd_counter:249 (max:1441)
Mar 16 01:15:14 guruvdr kernel: itd_counter:0 (max:1441)
[...]
Mar 16 02:03:33 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:04:15 guruvdr kernel: itd_counter:150 (max:1441)
Mar 16 02:04:15 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:04:36 guruvdr kernel: itd_counter:42 (max:1441)
Mar 16 02:04:36 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:04:57 guruvdr kernel: itd_counter:42 (max:1441)
Mar 16 02:04:57 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:05:18 guruvdr kernel: itd_counter:42 (max:1441)
Mar 16 02:05:18 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:05:39 guruvdr kernel: itd_counter:42 (max:1441)
Mar 16 02:05:39 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:06:43 guruvdr kernel: itd_counter:254 (max:1441)
Mar 16 02:07:44 guruvdr kernel: itd_counter:968 (max:1469)
Mar 16 02:08:04 guruvdr kernel: itd_counter:1192 (max:1469)
Mar 16 02:08:46 guruvdr kernel: itd_counter:1812 (max:1854)
Mar 16 02:09:07 guruvdr kernel: itd_counter:2117 (max:2159)
Mar 16 02:09:28 guruvdr kernel: itd_counter:2482 (max:2524)
Mar 16 02:09:49 guruvdr kernel: itd_counter:2791 (max:2833)
Mar 16 02:10:10 guruvdr kernel: itd_counter:3088 (max:3409)
Mar 16 02:10:31 guruvdr kernel: itd_counter:3402 (max:3444)
Mar 16 02:10:52 guruvdr kernel: itd_counter:3689 (max:3731)
Mar 16 02:11:13 guruvdr kernel: itd_counter:3950 (max:4073)
Mar 16 02:11:34 guruvdr kernel: itd_counter:4264 (max:4306)
Mar 16 02:11:55 guruvdr kernel: itd_counter:4525 (max:4567)
Mar 16 02:12:16 guruvdr kernel: itd_counter:4803 (max:4845)
Mar 16 02:12:37 guruvdr kernel: itd_counter:5028 (max:5070)
Mar 16 02:13:19 guruvdr kernel: itd_counter:5549 (max:5843)
Mar 16 02:13:40 guruvdr kernel: itd_counter:5836 (max:5878)
Mar 16 02:14:01 guruvdr kernel: itd_counter:6133 (max:6238)
Mar 16 02:14:06 guruvdr kernel: ERROR: 1024 KiB atomic DMA coherent pool 
is too small!
Mar 16 02:14:06 guruvdr kernel: Please increase it with coherent_pool= 
kernel parameter!
Mar 16 02:14:06 guruvdr kernel: itd_counter:6275
Mar 16 02:14:06 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:06 guruvdr kernel: itd_counter:6275
Mar 16 02:14:06 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:06 guruvdr kernel: itd_counter:6275
Mar 16 02:14:06 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:06 guruvdr kernel: itd_counter:6275
Mar 16 02:14:06 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:07 guruvdr kernel: itd_counter:6275
Mar 16 02:14:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:07 guruvdr kernel: itd_counter:6275
Mar 16 02:14:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:07 guruvdr kernel: itd_counter:6275
Mar 16 02:14:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:07 guruvdr kernel: itd_counter:6275
Mar 16 02:14:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:08 guruvdr kernel: itd_counter:6275
Mar 16 02:14:08 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:08 guruvdr kernel: itd_counter:78 (max:6275)
Mar 16 02:14:22 guruvdr kernel: itd_counter:0 (max:6275)

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 14.03.2013 22:33, Alan Stern wrote:
> Maybe a better way to go about this is, instead of printing out every
> allocation and deallocation, to keep a running counter.  You could have
> the driver print out the value of this counter every minute or so.  Any
> time the device isn't in use, the counter should be 0.

I implemented the counter. The max value is sampled at the beginning of 
end_free_itds(), the current counter value is sampled at the end of this 
function. Counter values w/o a max number are from the error path in 
itd_urb_transaction().
The number of allocated iTDs can grow to higher values (why?), but 
normally the iTDs are freed during normal operation. Due to some reason 
the number of iTDs suddenly increases until coherent pool exhaustion. 
There is no permanent memory leak, all iTDs are released when the user 
application ends. But imho several thousands of iTDs cannot be the 
intended behavior...

   Soeren


Mar 16 01:12:52 guruvdr kernel: itd_counter:42 (max:174)
Mar 16 01:12:52 guruvdr kernel: itd_counter:0 (max:174)
Mar 16 01:13:13 guruvdr kernel: itd_counter:42 (max:174)
Mar 16 01:13:13 guruvdr kernel: itd_counter:0 (max:174)
Mar 16 01:13:34 guruvdr kernel: itd_counter:87 (max:174)
Mar 16 01:13:34 guruvdr kernel: itd_counter:0 (max:174)
Mar 16 01:13:55 guruvdr kernel: itd_counter:42 (max:426)
Mar 16 01:13:55 guruvdr kernel: itd_counter:0 (max:426)
Mar 16 01:15:14 guruvdr kernel: itd_counter:249 (max:1441)
Mar 16 01:15:14 guruvdr kernel: itd_counter:0 (max:1441)
[...]
Mar 16 02:03:33 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:04:15 guruvdr kernel: itd_counter:150 (max:1441)
Mar 16 02:04:15 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:04:36 guruvdr kernel: itd_counter:42 (max:1441)
Mar 16 02:04:36 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:04:57 guruvdr kernel: itd_counter:42 (max:1441)
Mar 16 02:04:57 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:05:18 guruvdr kernel: itd_counter:42 (max:1441)
Mar 16 02:05:18 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:05:39 guruvdr kernel: itd_counter:42 (max:1441)
Mar 16 02:05:39 guruvdr kernel: itd_counter:0 (max:1441)
Mar 16 02:06:43 guruvdr kernel: itd_counter:254 (max:1441)
Mar 16 02:07:44 guruvdr kernel: itd_counter:968 (max:1469)
Mar 16 02:08:04 guruvdr kernel: itd_counter:1192 (max:1469)
Mar 16 02:08:46 guruvdr kernel: itd_counter:1812 (max:1854)
Mar 16 02:09:07 guruvdr kernel: itd_counter:2117 (max:2159)
Mar 16 02:09:28 guruvdr kernel: itd_counter:2482 (max:2524)
Mar 16 02:09:49 guruvdr kernel: itd_counter:2791 (max:2833)
Mar 16 02:10:10 guruvdr kernel: itd_counter:3088 (max:3409)
Mar 16 02:10:31 guruvdr kernel: itd_counter:3402 (max:3444)
Mar 16 02:10:52 guruvdr kernel: itd_counter:3689 (max:3731)
Mar 16 02:11:13 guruvdr kernel: itd_counter:3950 (max:4073)
Mar 16 02:11:34 guruvdr kernel: itd_counter:4264 (max:4306)
Mar 16 02:11:55 guruvdr kernel: itd_counter:4525 (max:4567)
Mar 16 02:12:16 guruvdr kernel: itd_counter:4803 (max:4845)
Mar 16 02:12:37 guruvdr kernel: itd_counter:5028 (max:5070)
Mar 16 02:13:19 guruvdr kernel: itd_counter:5549 (max:5843)
Mar 16 02:13:40 guruvdr kernel: itd_counter:5836 (max:5878)
Mar 16 02:14:01 guruvdr kernel: itd_counter:6133 (max:6238)
Mar 16 02:14:06 guruvdr kernel: ERROR: 1024 KiB atomic DMA coherent pool 
is too small!
Mar 16 02:14:06 guruvdr kernel: Please increase it with coherent_pool= 
kernel parameter!
Mar 16 02:14:06 guruvdr kernel: itd_counter:6275
Mar 16 02:14:06 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:06 guruvdr kernel: itd_counter:6275
Mar 16 02:14:06 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:06 guruvdr kernel: itd_counter:6275
Mar 16 02:14:06 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:06 guruvdr kernel: itd_counter:6275
Mar 16 02:14:06 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:07 guruvdr kernel: itd_counter:6275
Mar 16 02:14:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:07 guruvdr kernel: itd_counter:6275
Mar 16 02:14:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:07 guruvdr kernel: itd_counter:6275
Mar 16 02:14:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:07 guruvdr kernel: itd_counter:6275
Mar 16 02:14:07 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:08 guruvdr kernel: itd_counter:6275
Mar 16 02:14:08 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 16 02:14:08 guruvdr kernel: itd_counter:78 (max:6275)
Mar 16 02:14:22 guruvdr kernel: itd_counter:0 (max:6275)

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Sat, 16 Mar 2013, Soeren Moch wrote:

> I implemented the counter. The max value is sampled at the beginning of 
> end_free_itds(), the current counter value is sampled at the end of this 
> function. Counter values w/o a max number are from the error path in 
> itd_urb_transaction().
> The number of allocated iTDs can grow to higher values (why?), but 
> normally the iTDs are freed during normal operation. Due to some reason 
> the number of iTDs suddenly increases until coherent pool exhaustion. 
> There is no permanent memory leak, all iTDs are released when the user 
> application ends. But imho several thousands of iTDs cannot be the 
> intended behavior...

No, it's not.  Here's how it's supposed to work:

Each ehci_iso_stream structure corresponds to a single isochronous
endpoint.  The structure has a free list of iTDs that aren't currently
in use; when an URB is submitted, its iTDs are taken from the start of
this free list if possible.  Otherwise new iTDs are allocated from the
DMA pool.

iTDs on the free list aren't always available.  This is because the 
hardware can continue to access an iTD for up to 1 ms after the iTD has 
completed.  itd->frame stores the frame number (one frame per ms) for 
when the iTD completes, and ehci->now_frame contains a best estimate of 
the current frame number.  This explains the logic in 
itd_urb_transaction().  Near the end of itd_complete() you can see 
where a completed iTD gets added back to the end of the free list.

At the very end of itd_complete() is a section of code that takes the
entries on the iso_stream's free list and moves them to a global free
list (ehci->cached_itd_list).  This happens only when the endpoint is
no longer in use, i.e., no iTDs are queued for it.  The end_free_itds()  
routine in ehci_timer.c takes iTDs from this global list and releases
them back to the DMA pool.  The routine doesn't run until at least 1 ms
after start_free_itds() is called, to wait for the hardware to stop
accessing the iTDs on the list.

The idea is that during normal use we will quickly reach a steady
state, where an endpoint always has about N URBs queued for it, each
URB uses about M iTDs, and there are one or two URB's worth of unused
iTDs.  Thus there will be N*M iTDs in use plus maybe another 2*M iTDs
on the iso_stream's free list.  Once we reach this point, every new URB
should be able to get the iTDs it needs from the free list (assuming a
new URB is submitted every time an URB completes).  When the URBs stop
being submitted, the pipeline will empty out and after a couple more
milliseconds, all (N+2)*M iTDs should be released back to the pool.

In your case the situation is complicated by the fact that you're using
two devices, each of which has up to four isochronous endpoints.  This
makes it harder to see what's going on.  Probably not all of the 
endpoints were being used for data transfers.  But even if they were, 
there should not have been more then 800 iTDs allocated at any time 
(figure that N is around 5 and M is 9).  You could simplify the testing 
by using only one device -- it might not exhaust the pool but your iTD
counter would still indicate if something wasn't right.

I'm not sure how to figure out what's causing the problem.  Maybe you
can think of a good way to see where the actual operation differs from
the description above.  Perhaps start by keeping track of the number of
iTDs on each iso_stream's free list and the number in use by each
iso_stream.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Sat, 16 Mar 2013, Soeren Moch wrote:

> I implemented the counter. The max value is sampled at the beginning of 
> end_free_itds(), the current counter value is sampled at the end of this 
> function. Counter values w/o a max number are from the error path in 
> itd_urb_transaction().
> The number of allocated iTDs can grow to higher values (why?), but 
> normally the iTDs are freed during normal operation. Due to some reason 
> the number of iTDs suddenly increases until coherent pool exhaustion. 
> There is no permanent memory leak, all iTDs are released when the user 
> application ends. But imho several thousands of iTDs cannot be the 
> intended behavior...

No, it's not.  Here's how it's supposed to work:

Each ehci_iso_stream structure corresponds to a single isochronous
endpoint.  The structure has a free list of iTDs that aren't currently
in use; when an URB is submitted, its iTDs are taken from the start of
this free list if possible.  Otherwise new iTDs are allocated from the
DMA pool.

iTDs on the free list aren't always available.  This is because the 
hardware can continue to access an iTD for up to 1 ms after the iTD has 
completed.  itd->frame stores the frame number (one frame per ms) for 
when the iTD completes, and ehci->now_frame contains a best estimate of 
the current frame number.  This explains the logic in 
itd_urb_transaction().  Near the end of itd_complete() you can see 
where a completed iTD gets added back to the end of the free list.

At the very end of itd_complete() is a section of code that takes the
entries on the iso_stream's free list and moves them to a global free
list (ehci->cached_itd_list).  This happens only when the endpoint is
no longer in use, i.e., no iTDs are queued for it.  The end_free_itds()  
routine in ehci_timer.c takes iTDs from this global list and releases
them back to the DMA pool.  The routine doesn't run until at least 1 ms
after start_free_itds() is called, to wait for the hardware to stop
accessing the iTDs on the list.

The idea is that during normal use we will quickly reach a steady
state, where an endpoint always has about N URBs queued for it, each
URB uses about M iTDs, and there are one or two URB's worth of unused
iTDs.  Thus there will be N*M iTDs in use plus maybe another 2*M iTDs
on the iso_stream's free list.  Once we reach this point, every new URB
should be able to get the iTDs it needs from the free list (assuming a
new URB is submitted every time an URB completes).  When the URBs stop
being submitted, the pipeline will empty out and after a couple more
milliseconds, all (N+2)*M iTDs should be released back to the pool.

In your case the situation is complicated by the fact that you're using
two devices, each of which has up to four isochronous endpoints.  This
makes it harder to see what's going on.  Probably not all of the 
endpoints were being used for data transfers.  But even if they were, 
there should not have been more then 800 iTDs allocated at any time 
(figure that N is around 5 and M is 9).  You could simplify the testing 
by using only one device -- it might not exhaust the pool but your iTD
counter would still indicate if something wasn't right.

I'm not sure how to figure out what's causing the problem.  Maybe you
can think of a good way to see where the actual operation differs from
the description above.  Perhaps start by keeping track of the number of
iTDs on each iso_stream's free list and the number in use by each
iso_stream.

Alan Stern

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Sat, 16 Mar 2013, Soeren Moch wrote:

> I implemented the counter. The max value is sampled at the beginning of 
> end_free_itds(), the current counter value is sampled at the end of this 
> function. Counter values w/o a max number are from the error path in 
> itd_urb_transaction().
> The number of allocated iTDs can grow to higher values (why?), but 
> normally the iTDs are freed during normal operation. Due to some reason 
> the number of iTDs suddenly increases until coherent pool exhaustion. 
> There is no permanent memory leak, all iTDs are released when the user 
> application ends. But imho several thousands of iTDs cannot be the 
> intended behavior...

No, it's not.  Here's how it's supposed to work:

Each ehci_iso_stream structure corresponds to a single isochronous
endpoint.  The structure has a free list of iTDs that aren't currently
in use; when an URB is submitted, its iTDs are taken from the start of
this free list if possible.  Otherwise new iTDs are allocated from the
DMA pool.

iTDs on the free list aren't always available.  This is because the 
hardware can continue to access an iTD for up to 1 ms after the iTD has 
completed.  itd->frame stores the frame number (one frame per ms) for 
when the iTD completes, and ehci->now_frame contains a best estimate of 
the current frame number.  This explains the logic in 
itd_urb_transaction().  Near the end of itd_complete() you can see 
where a completed iTD gets added back to the end of the free list.

At the very end of itd_complete() is a section of code that takes the
entries on the iso_stream's free list and moves them to a global free
list (ehci->cached_itd_list).  This happens only when the endpoint is
no longer in use, i.e., no iTDs are queued for it.  The end_free_itds()  
routine in ehci_timer.c takes iTDs from this global list and releases
them back to the DMA pool.  The routine doesn't run until at least 1 ms
after start_free_itds() is called, to wait for the hardware to stop
accessing the iTDs on the list.

The idea is that during normal use we will quickly reach a steady
state, where an endpoint always has about N URBs queued for it, each
URB uses about M iTDs, and there are one or two URB's worth of unused
iTDs.  Thus there will be N*M iTDs in use plus maybe another 2*M iTDs
on the iso_stream's free list.  Once we reach this point, every new URB
should be able to get the iTDs it needs from the free list (assuming a
new URB is submitted every time an URB completes).  When the URBs stop
being submitted, the pipeline will empty out and after a couple more
milliseconds, all (N+2)*M iTDs should be released back to the pool.

In your case the situation is complicated by the fact that you're using
two devices, each of which has up to four isochronous endpoints.  This
makes it harder to see what's going on.  Probably not all of the 
endpoints were being used for data transfers.  But even if they were, 
there should not have been more then 800 iTDs allocated at any time 
(figure that N is around 5 and M is 9).  You could simplify the testing 
by using only one device -- it might not exhaust the pool but your iTD
counter would still indicate if something wasn't right.

I'm not sure how to figure out what's causing the problem.  Maybe you
can think of a good way to see where the actual operation differs from
the description above.  Perhaps start by keeping track of the number of
iTDs on each iso_stream's free list and the number in use by each
iso_stream.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 16.03.2013 18:39, Alan Stern wrote:
> On Sat, 16 Mar 2013, Soeren Moch wrote:
>
>> I implemented the counter. The max value is sampled at the beginning of
>> end_free_itds(), the current counter value is sampled at the end of this
>> function. Counter values w/o a max number are from the error path in
>> itd_urb_transaction().
>> The number of allocated iTDs can grow to higher values (why?), but
>> normally the iTDs are freed during normal operation. Due to some reason
>> the number of iTDs suddenly increases until coherent pool exhaustion.
>> There is no permanent memory leak, all iTDs are released when the user
>> application ends. But imho several thousands of iTDs cannot be the
>> intended behavior...
>
> No, it's not.  Here's how it's supposed to work:
>
> Each ehci_iso_stream structure corresponds to a single isochronous
> endpoint.  The structure has a free list of iTDs that aren't currently
> in use; when an URB is submitted, its iTDs are taken from the start of
> this free list if possible.  Otherwise new iTDs are allocated from the
> DMA pool.
>
> iTDs on the free list aren't always available.  This is because the
> hardware can continue to access an iTD for up to 1 ms after the iTD has
> completed.  itd->frame stores the frame number (one frame per ms) for
> when the iTD completes, and ehci->now_frame contains a best estimate of
> the current frame number.  This explains the logic in
> itd_urb_transaction().  Near the end of itd_complete() you can see
> where a completed iTD gets added back to the end of the free list.
>
> At the very end of itd_complete() is a section of code that takes the
> entries on the iso_stream's free list and moves them to a global free
> list (ehci->cached_itd_list).  This happens only when the endpoint is
> no longer in use, i.e., no iTDs are queued for it.  The end_free_itds()
> routine in ehci_timer.c takes iTDs from this global list and releases
> them back to the DMA pool.  The routine doesn't run until at least 1 ms
> after start_free_itds() is called, to wait for the hardware to stop
> accessing the iTDs on the list.
>
> The idea is that during normal use we will quickly reach a steady
> state, where an endpoint always has about N URBs queued for it, each
> URB uses about M iTDs, and there are one or two URB's worth of unused
> iTDs.  Thus there will be N*M iTDs in use plus maybe another 2*M iTDs
> on the iso_stream's free list.  Once we reach this point, every new URB
> should be able to get the iTDs it needs from the free list (assuming a
> new URB is submitted every time an URB completes).  When the URBs stop
> being submitted, the pipeline will empty out and after a couple more
> milliseconds, all (N+2)*M iTDs should be released back to the pool.
>
> In your case the situation is complicated by the fact that you're using
> two devices, each of which has up to four isochronous endpoints.  This
> makes it harder to see what's going on.  Probably not all of the
> endpoints were being used for data transfers.  But even if they were,
> there should not have been more then 800 iTDs allocated at any time
> (figure that N is around 5 and M is 9).  You could simplify the testing
> by using only one device -- it might not exhaust the pool but your iTD
> counter would still indicate if something wasn't right.
>
> I'm not sure how to figure out what's causing the problem.  Maybe you
> can think of a good way to see where the actual operation differs from
> the description above.  Perhaps start by keeping track of the number of
> iTDs on each iso_stream's free list and the number in use by each
> iso_stream.


For each device only one isochronous endpoint is used (EP IN4, 1x 940 
Bytes, Interval 1).
When the ENOMEM error occurs, a huge number of iTDs is in the free_list 
of one stream. This number is much higher than the 2*M entries, which 
should be there according to your description.

  Soeren Moch


Mar 17 17:06:49 guruvdr kernel: free iso_stream:0xd802d840
Mar 17 17:06:49 guruvdr kernel: iso_stream_init: stream:0xd802d7e0 dev:5 
ep:132 int:1 maxp:940 bw:152
Mar 17 17:06:50 guruvdr kernel: free iso_stream:0xd802d9c0
Mar 17 17:06:50 guruvdr kernel: iso_stream_init: stream:0xd802d360 dev:6 
ep:132 int:1 maxp:940 bw:152
Mar 17 17:07:09 guruvdr kernel: itd_counter:42 (max:4549)
Mar 17 17:07:09 guruvdr kernel: itd_counter:0 (max:4549)
Mar 17 17:07:10 guruvdr kernel: free iso_stream:0xd802d7e0
Mar 17 17:07:11 guruvdr kernel: iso_stream_init: stream:0xd802d7e0 dev:5 
ep:132 int:1 maxp:940 bw:152
Mar 17 17:07:11 guruvdr kernel: free iso_stream:0xd802d360
Mar 17 17:07:11 guruvdr kernel: iso_stream_init: stream:0xd802d360 dev:6 
ep:132 int:1 maxp:940 bw:152
Mar 17 17:15:13 guruvdr kernel: ERROR: 1024 KiB atomic DMA coherent pool 
is too small!
Mar 17 17:15:13 guruvdr kernel: Please increase it with coherent_pool= 
kernel parameter!
Mar 17 17:15:13 guruvdr kernel: itd_counter:6275
Mar 17 17:15:13 guruvdr kernel: stream0 num_td_list_entries:33 
num_free_list_entries:6200
Mar 17 17:15:13 guruvdr kernel: stream1 num_td_list_entries:36 
num_free_list_entries:6
Mar 17 17:15:13 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 17 17:15:13 guruvdr kernel: itd_counter:6275
Mar 17 17:15:13 guruvdr kernel: stream0 num_td_list_entries:25 
num_free_list_entries:6208
Mar 17 17:15:13 guruvdr kernel: stream1 num_td_list_entries:35 
num_free_list_entries:7
Mar 17 17:15:13 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 17 17:15:14 guruvdr kernel: itd_counter:6275
Mar 17 17:15:14 guruvdr kernel: stream0 num_td_list_entries:17 
num_free_list_entries:6216
Mar 17 17:15:14 guruvdr kernel: stream1 num_td_list_entries:35 
num_free_list_entries:7
Mar 17 17:15:14 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 17 17:15:14 guruvdr kernel: itd_counter:6275
Mar 17 17:15:14 guruvdr kernel: stream0 num_td_list_entries:9 
num_free_list_entries:6224
Mar 17 17:15:14 guruvdr kernel: stream1 num_td_list_entries:35 
num_free_list_entries:7
Mar 17 17:15:14 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 17 17:15:16 guruvdr kernel: itd_counter:6275
Mar 17 17:15:16 guruvdr kernel: stream0 num_td_list_entries:1 
num_free_list_entries:6232
Mar 17 17:15:16 guruvdr kernel: stream1 num_td_list_entries:40 
num_free_list_entries:2
Mar 17 17:15:16 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 17 17:15:16 guruvdr kernel: itd_counter:42 (max:6275)
Mar 17 17:16:31 guruvdr kernel: itd_counter:0 (max:6275)
Mar 17 17:16:32 guruvdr kernel: free iso_stream:0xd802d7e0
Mar 17 17:16:32 guruvdr kernel: iso_stream_init: stream:0xd802d6c0 dev:5 
ep:132 int:1 maxp:940 bw:152
Mar 17 17:16:36 guruvdr kernel: free iso_stream:0xd802d360
Mar 17 17:16:36 guruvdr kernel: iso_stream_init: stream:0xd802da20 dev:6 
ep:132 int:1 maxp:940 bw:152

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 16.03.2013 18:39, Alan Stern wrote:
> On Sat, 16 Mar 2013, Soeren Moch wrote:
>
>> I implemented the counter. The max value is sampled at the beginning of
>> end_free_itds(), the current counter value is sampled at the end of this
>> function. Counter values w/o a max number are from the error path in
>> itd_urb_transaction().
>> The number of allocated iTDs can grow to higher values (why?), but
>> normally the iTDs are freed during normal operation. Due to some reason
>> the number of iTDs suddenly increases until coherent pool exhaustion.
>> There is no permanent memory leak, all iTDs are released when the user
>> application ends. But imho several thousands of iTDs cannot be the
>> intended behavior...
>
> No, it's not.  Here's how it's supposed to work:
>
> Each ehci_iso_stream structure corresponds to a single isochronous
> endpoint.  The structure has a free list of iTDs that aren't currently
> in use; when an URB is submitted, its iTDs are taken from the start of
> this free list if possible.  Otherwise new iTDs are allocated from the
> DMA pool.
>
> iTDs on the free list aren't always available.  This is because the
> hardware can continue to access an iTD for up to 1 ms after the iTD has
> completed.  itd->frame stores the frame number (one frame per ms) for
> when the iTD completes, and ehci->now_frame contains a best estimate of
> the current frame number.  This explains the logic in
> itd_urb_transaction().  Near the end of itd_complete() you can see
> where a completed iTD gets added back to the end of the free list.
>
> At the very end of itd_complete() is a section of code that takes the
> entries on the iso_stream's free list and moves them to a global free
> list (ehci->cached_itd_list).  This happens only when the endpoint is
> no longer in use, i.e., no iTDs are queued for it.  The end_free_itds()
> routine in ehci_timer.c takes iTDs from this global list and releases
> them back to the DMA pool.  The routine doesn't run until at least 1 ms
> after start_free_itds() is called, to wait for the hardware to stop
> accessing the iTDs on the list.
>
> The idea is that during normal use we will quickly reach a steady
> state, where an endpoint always has about N URBs queued for it, each
> URB uses about M iTDs, and there are one or two URB's worth of unused
> iTDs.  Thus there will be N*M iTDs in use plus maybe another 2*M iTDs
> on the iso_stream's free list.  Once we reach this point, every new URB
> should be able to get the iTDs it needs from the free list (assuming a
> new URB is submitted every time an URB completes).  When the URBs stop
> being submitted, the pipeline will empty out and after a couple more
> milliseconds, all (N+2)*M iTDs should be released back to the pool.
>
> In your case the situation is complicated by the fact that you're using
> two devices, each of which has up to four isochronous endpoints.  This
> makes it harder to see what's going on.  Probably not all of the
> endpoints were being used for data transfers.  But even if they were,
> there should not have been more then 800 iTDs allocated at any time
> (figure that N is around 5 and M is 9).  You could simplify the testing
> by using only one device -- it might not exhaust the pool but your iTD
> counter would still indicate if something wasn't right.
>
> I'm not sure how to figure out what's causing the problem.  Maybe you
> can think of a good way to see where the actual operation differs from
> the description above.  Perhaps start by keeping track of the number of
> iTDs on each iso_stream's free list and the number in use by each
> iso_stream.


For each device only one isochronous endpoint is used (EP IN4, 1x 940 
Bytes, Interval 1).
When the ENOMEM error occurs, a huge number of iTDs is in the free_list 
of one stream. This number is much higher than the 2*M entries, which 
should be there according to your description.

  Soeren Moch


Mar 17 17:06:49 guruvdr kernel: free iso_stream:0xd802d840
Mar 17 17:06:49 guruvdr kernel: iso_stream_init: stream:0xd802d7e0 dev:5 
ep:132 int:1 maxp:940 bw:152
Mar 17 17:06:50 guruvdr kernel: free iso_stream:0xd802d9c0
Mar 17 17:06:50 guruvdr kernel: iso_stream_init: stream:0xd802d360 dev:6 
ep:132 int:1 maxp:940 bw:152
Mar 17 17:07:09 guruvdr kernel: itd_counter:42 (max:4549)
Mar 17 17:07:09 guruvdr kernel: itd_counter:0 (max:4549)
Mar 17 17:07:10 guruvdr kernel: free iso_stream:0xd802d7e0
Mar 17 17:07:11 guruvdr kernel: iso_stream_init: stream:0xd802d7e0 dev:5 
ep:132 int:1 maxp:940 bw:152
Mar 17 17:07:11 guruvdr kernel: free iso_stream:0xd802d360
Mar 17 17:07:11 guruvdr kernel: iso_stream_init: stream:0xd802d360 dev:6 
ep:132 int:1 maxp:940 bw:152
Mar 17 17:15:13 guruvdr kernel: ERROR: 1024 KiB atomic DMA coherent pool 
is too small!
Mar 17 17:15:13 guruvdr kernel: Please increase it with coherent_pool= 
kernel parameter!
Mar 17 17:15:13 guruvdr kernel: itd_counter:6275
Mar 17 17:15:13 guruvdr kernel: stream0 num_td_list_entries:33 
num_free_list_entries:6200
Mar 17 17:15:13 guruvdr kernel: stream1 num_td_list_entries:36 
num_free_list_entries:6
Mar 17 17:15:13 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 17 17:15:13 guruvdr kernel: itd_counter:6275
Mar 17 17:15:13 guruvdr kernel: stream0 num_td_list_entries:25 
num_free_list_entries:6208
Mar 17 17:15:13 guruvdr kernel: stream1 num_td_list_entries:35 
num_free_list_entries:7
Mar 17 17:15:13 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 17 17:15:14 guruvdr kernel: itd_counter:6275
Mar 17 17:15:14 guruvdr kernel: stream0 num_td_list_entries:17 
num_free_list_entries:6216
Mar 17 17:15:14 guruvdr kernel: stream1 num_td_list_entries:35 
num_free_list_entries:7
Mar 17 17:15:14 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 17 17:15:14 guruvdr kernel: itd_counter:6275
Mar 17 17:15:14 guruvdr kernel: stream0 num_td_list_entries:9 
num_free_list_entries:6224
Mar 17 17:15:14 guruvdr kernel: stream1 num_td_list_entries:35 
num_free_list_entries:7
Mar 17 17:15:14 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 17 17:15:16 guruvdr kernel: itd_counter:6275
Mar 17 17:15:16 guruvdr kernel: stream0 num_td_list_entries:1 
num_free_list_entries:6232
Mar 17 17:15:16 guruvdr kernel: stream1 num_td_list_entries:40 
num_free_list_entries:2
Mar 17 17:15:16 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 17 17:15:16 guruvdr kernel: itd_counter:42 (max:6275)
Mar 17 17:16:31 guruvdr kernel: itd_counter:0 (max:6275)
Mar 17 17:16:32 guruvdr kernel: free iso_stream:0xd802d7e0
Mar 17 17:16:32 guruvdr kernel: iso_stream_init: stream:0xd802d6c0 dev:5 
ep:132 int:1 maxp:940 bw:152
Mar 17 17:16:36 guruvdr kernel: free iso_stream:0xd802d360
Mar 17 17:16:36 guruvdr kernel: iso_stream_init: stream:0xd802da20 dev:6 
ep:132 int:1 maxp:940 bw:152

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 16.03.2013 18:39, Alan Stern wrote:
> On Sat, 16 Mar 2013, Soeren Moch wrote:
>
>> I implemented the counter. The max value is sampled at the beginning of
>> end_free_itds(), the current counter value is sampled at the end of this
>> function. Counter values w/o a max number are from the error path in
>> itd_urb_transaction().
>> The number of allocated iTDs can grow to higher values (why?), but
>> normally the iTDs are freed during normal operation. Due to some reason
>> the number of iTDs suddenly increases until coherent pool exhaustion.
>> There is no permanent memory leak, all iTDs are released when the user
>> application ends. But imho several thousands of iTDs cannot be the
>> intended behavior...
>
> No, it's not.  Here's how it's supposed to work:
>
> Each ehci_iso_stream structure corresponds to a single isochronous
> endpoint.  The structure has a free list of iTDs that aren't currently
> in use; when an URB is submitted, its iTDs are taken from the start of
> this free list if possible.  Otherwise new iTDs are allocated from the
> DMA pool.
>
> iTDs on the free list aren't always available.  This is because the
> hardware can continue to access an iTD for up to 1 ms after the iTD has
> completed.  itd->frame stores the frame number (one frame per ms) for
> when the iTD completes, and ehci->now_frame contains a best estimate of
> the current frame number.  This explains the logic in
> itd_urb_transaction().  Near the end of itd_complete() you can see
> where a completed iTD gets added back to the end of the free list.
>
> At the very end of itd_complete() is a section of code that takes the
> entries on the iso_stream's free list and moves them to a global free
> list (ehci->cached_itd_list).  This happens only when the endpoint is
> no longer in use, i.e., no iTDs are queued for it.  The end_free_itds()
> routine in ehci_timer.c takes iTDs from this global list and releases
> them back to the DMA pool.  The routine doesn't run until at least 1 ms
> after start_free_itds() is called, to wait for the hardware to stop
> accessing the iTDs on the list.
>
> The idea is that during normal use we will quickly reach a steady
> state, where an endpoint always has about N URBs queued for it, each
> URB uses about M iTDs, and there are one or two URB's worth of unused
> iTDs.  Thus there will be N*M iTDs in use plus maybe another 2*M iTDs
> on the iso_stream's free list.  Once we reach this point, every new URB
> should be able to get the iTDs it needs from the free list (assuming a
> new URB is submitted every time an URB completes).  When the URBs stop
> being submitted, the pipeline will empty out and after a couple more
> milliseconds, all (N+2)*M iTDs should be released back to the pool.
>
> In your case the situation is complicated by the fact that you're using
> two devices, each of which has up to four isochronous endpoints.  This
> makes it harder to see what's going on.  Probably not all of the
> endpoints were being used for data transfers.  But even if they were,
> there should not have been more then 800 iTDs allocated at any time
> (figure that N is around 5 and M is 9).  You could simplify the testing
> by using only one device -- it might not exhaust the pool but your iTD
> counter would still indicate if something wasn't right.
>
> I'm not sure how to figure out what's causing the problem.  Maybe you
> can think of a good way to see where the actual operation differs from
> the description above.  Perhaps start by keeping track of the number of
> iTDs on each iso_stream's free list and the number in use by each
> iso_stream.


For each device only one isochronous endpoint is used (EP IN4, 1x 940 
Bytes, Interval 1).
When the ENOMEM error occurs, a huge number of iTDs is in the free_list 
of one stream. This number is much higher than the 2*M entries, which 
should be there according to your description.

  Soeren Moch


Mar 17 17:06:49 guruvdr kernel: free iso_stream:0xd802d840
Mar 17 17:06:49 guruvdr kernel: iso_stream_init: stream:0xd802d7e0 dev:5 
ep:132 int:1 maxp:940 bw:152
Mar 17 17:06:50 guruvdr kernel: free iso_stream:0xd802d9c0
Mar 17 17:06:50 guruvdr kernel: iso_stream_init: stream:0xd802d360 dev:6 
ep:132 int:1 maxp:940 bw:152
Mar 17 17:07:09 guruvdr kernel: itd_counter:42 (max:4549)
Mar 17 17:07:09 guruvdr kernel: itd_counter:0 (max:4549)
Mar 17 17:07:10 guruvdr kernel: free iso_stream:0xd802d7e0
Mar 17 17:07:11 guruvdr kernel: iso_stream_init: stream:0xd802d7e0 dev:5 
ep:132 int:1 maxp:940 bw:152
Mar 17 17:07:11 guruvdr kernel: free iso_stream:0xd802d360
Mar 17 17:07:11 guruvdr kernel: iso_stream_init: stream:0xd802d360 dev:6 
ep:132 int:1 maxp:940 bw:152
Mar 17 17:15:13 guruvdr kernel: ERROR: 1024 KiB atomic DMA coherent pool 
is too small!
Mar 17 17:15:13 guruvdr kernel: Please increase it with coherent_pool= 
kernel parameter!
Mar 17 17:15:13 guruvdr kernel: itd_counter:6275
Mar 17 17:15:13 guruvdr kernel: stream0 num_td_list_entries:33 
num_free_list_entries:6200
Mar 17 17:15:13 guruvdr kernel: stream1 num_td_list_entries:36 
num_free_list_entries:6
Mar 17 17:15:13 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 17 17:15:13 guruvdr kernel: itd_counter:6275
Mar 17 17:15:13 guruvdr kernel: stream0 num_td_list_entries:25 
num_free_list_entries:6208
Mar 17 17:15:13 guruvdr kernel: stream1 num_td_list_entries:35 
num_free_list_entries:7
Mar 17 17:15:13 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 17 17:15:14 guruvdr kernel: itd_counter:6275
Mar 17 17:15:14 guruvdr kernel: stream0 num_td_list_entries:17 
num_free_list_entries:6216
Mar 17 17:15:14 guruvdr kernel: stream1 num_td_list_entries:35 
num_free_list_entries:7
Mar 17 17:15:14 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 17 17:15:14 guruvdr kernel: itd_counter:6275
Mar 17 17:15:14 guruvdr kernel: stream0 num_td_list_entries:9 
num_free_list_entries:6224
Mar 17 17:15:14 guruvdr kernel: stream1 num_td_list_entries:35 
num_free_list_entries:7
Mar 17 17:15:14 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 17 17:15:16 guruvdr kernel: itd_counter:6275
Mar 17 17:15:16 guruvdr kernel: stream0 num_td_list_entries:1 
num_free_list_entries:6232
Mar 17 17:15:16 guruvdr kernel: stream1 num_td_list_entries:40 
num_free_list_entries:2
Mar 17 17:15:16 guruvdr kernel: orion-ehci orion-ehci.0: can't init itds
Mar 17 17:15:16 guruvdr kernel: itd_counter:42 (max:6275)
Mar 17 17:16:31 guruvdr kernel: itd_counter:0 (max:6275)
Mar 17 17:16:32 guruvdr kernel: free iso_stream:0xd802d7e0
Mar 17 17:16:32 guruvdr kernel: iso_stream_init: stream:0xd802d6c0 dev:5 
ep:132 int:1 maxp:940 bw:152
Mar 17 17:16:36 guruvdr kernel: free iso_stream:0xd802d360
Mar 17 17:16:36 guruvdr kernel: iso_stream_init: stream:0xd802da20 dev:6 
ep:132 int:1 maxp:940 bw:152

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Sun, 17 Mar 2013, Soeren Moch wrote:

> For each device only one isochronous endpoint is used (EP IN4, 1x 940 
> Bytes, Interval 1).
> When the ENOMEM error occurs, a huge number of iTDs is in the free_list 
> of one stream. This number is much higher than the 2*M entries, which 
> should be there according to your description.

Okay, but how did they get there?  With each URB requiring 9 iTDs, and
about 5 URBs active at any time, there should be about 5*9 = 45 iTDs in
use and 2*9 = 18 iTDs on the free list.  By the time each URB
completes, it should have released all 9 iTDs back to the free list,
and each time an URB is submitted, it should be able to acquire all 9
of the iTDs that it needs from the free list -- it shouldn't have to 
allocate any from the DMA pool.

Looks like you'll have to investigate what's going on inside
itd_urb_transaction().  Print out some useful information whenever the
size of stream->free_list is above 50, such as the value of num_itds,
how many of the loop iterations could get an iTD from the free list,
and the value of itd->frame in the case where the "goto alloc_itd"
statement is followed.

It might be a good idea also to print out the size of the free list in
itd_complete(), where it calls ehci_urb_done(), and include the value
of ehci->now_frame.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Sun, 17 Mar 2013, Soeren Moch wrote:

> For each device only one isochronous endpoint is used (EP IN4, 1x 940 
> Bytes, Interval 1).
> When the ENOMEM error occurs, a huge number of iTDs is in the free_list 
> of one stream. This number is much higher than the 2*M entries, which 
> should be there according to your description.

Okay, but how did they get there?  With each URB requiring 9 iTDs, and
about 5 URBs active at any time, there should be about 5*9 = 45 iTDs in
use and 2*9 = 18 iTDs on the free list.  By the time each URB
completes, it should have released all 9 iTDs back to the free list,
and each time an URB is submitted, it should be able to acquire all 9
of the iTDs that it needs from the free list -- it shouldn't have to 
allocate any from the DMA pool.

Looks like you'll have to investigate what's going on inside
itd_urb_transaction().  Print out some useful information whenever the
size of stream->free_list is above 50, such as the value of num_itds,
how many of the loop iterations could get an iTD from the free list,
and the value of itd->frame in the case where the "goto alloc_itd"
statement is followed.

It might be a good idea also to print out the size of the free list in
itd_complete(), where it calls ehci_urb_done(), and include the value
of ehci->now_frame.

Alan Stern

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Sun, 17 Mar 2013, Soeren Moch wrote:

> For each device only one isochronous endpoint is used (EP IN4, 1x 940 
> Bytes, Interval 1).
> When the ENOMEM error occurs, a huge number of iTDs is in the free_list 
> of one stream. This number is much higher than the 2*M entries, which 
> should be there according to your description.

Okay, but how did they get there?  With each URB requiring 9 iTDs, and
about 5 URBs active at any time, there should be about 5*9 = 45 iTDs in
use and 2*9 = 18 iTDs on the free list.  By the time each URB
completes, it should have released all 9 iTDs back to the free list,
and each time an URB is submitted, it should be able to acquire all 9
of the iTDs that it needs from the free list -- it shouldn't have to 
allocate any from the DMA pool.

Looks like you'll have to investigate what's going on inside
itd_urb_transaction().  Print out some useful information whenever the
size of stream->free_list is above 50, such as the value of num_itds,
how many of the loop iterations could get an iTD from the free list,
and the value of itd->frame in the case where the "goto alloc_itd"
statement is followed.

It might be a good idea also to print out the size of the free list in
itd_complete(), where it calls ehci_urb_done(), and include the value
of ehci->now_frame.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Sun, 17 Mar 2013, Alan Stern wrote:

> On Sun, 17 Mar 2013, Soeren Moch wrote:
> 
> > For each device only one isochronous endpoint is used (EP IN4, 1x 940 
> > Bytes, Interval 1).
> > When the ENOMEM error occurs, a huge number of iTDs is in the free_list 
> > of one stream. This number is much higher than the 2*M entries, which 
> > should be there according to your description.
> 
> Okay, but how did they get there?  With each URB requiring 9 iTDs, and
> about 5 URBs active at any time, there should be about 5*9 = 45 iTDs in
> use and 2*9 = 18 iTDs on the free list.  By the time each URB
> completes, it should have released all 9 iTDs back to the free list,
> and each time an URB is submitted, it should be able to acquire all 9
> of the iTDs that it needs from the free list -- it shouldn't have to 
> allocate any from the DMA pool.
> 
> Looks like you'll have to investigate what's going on inside
> itd_urb_transaction().  Print out some useful information whenever the
> size of stream->free_list is above 50, such as the value of num_itds,
> how many of the loop iterations could get an iTD from the free list,
> and the value of itd->frame in the case where the "goto alloc_itd"
> statement is followed.
> 
> It might be a good idea also to print out the size of the free list in
> itd_complete(), where it calls ehci_urb_done(), and include the value
> of ehci->now_frame.

One thing I forgot to mention: It would help to have millisecond
precision for the timestamps in the system log, for comparison of frame
number values.  Please enable CONFIG_PRINTK_TIME for the next test.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Sun, 17 Mar 2013, Alan Stern wrote:

> On Sun, 17 Mar 2013, Soeren Moch wrote:
> 
> > For each device only one isochronous endpoint is used (EP IN4, 1x 940 
> > Bytes, Interval 1).
> > When the ENOMEM error occurs, a huge number of iTDs is in the free_list 
> > of one stream. This number is much higher than the 2*M entries, which 
> > should be there according to your description.
> 
> Okay, but how did they get there?  With each URB requiring 9 iTDs, and
> about 5 URBs active at any time, there should be about 5*9 = 45 iTDs in
> use and 2*9 = 18 iTDs on the free list.  By the time each URB
> completes, it should have released all 9 iTDs back to the free list,
> and each time an URB is submitted, it should be able to acquire all 9
> of the iTDs that it needs from the free list -- it shouldn't have to 
> allocate any from the DMA pool.
> 
> Looks like you'll have to investigate what's going on inside
> itd_urb_transaction().  Print out some useful information whenever the
> size of stream->free_list is above 50, such as the value of num_itds,
> how many of the loop iterations could get an iTD from the free list,
> and the value of itd->frame in the case where the "goto alloc_itd"
> statement is followed.
> 
> It might be a good idea also to print out the size of the free list in
> itd_complete(), where it calls ehci_urb_done(), and include the value
> of ehci->now_frame.

One thing I forgot to mention: It would help to have millisecond
precision for the timestamps in the system log, for comparison of frame
number values.  Please enable CONFIG_PRINTK_TIME for the next test.

Alan Stern

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Sun, 17 Mar 2013, Alan Stern wrote:

> On Sun, 17 Mar 2013, Soeren Moch wrote:
> 
> > For each device only one isochronous endpoint is used (EP IN4, 1x 940 
> > Bytes, Interval 1).
> > When the ENOMEM error occurs, a huge number of iTDs is in the free_list 
> > of one stream. This number is much higher than the 2*M entries, which 
> > should be there according to your description.
> 
> Okay, but how did they get there?  With each URB requiring 9 iTDs, and
> about 5 URBs active at any time, there should be about 5*9 = 45 iTDs in
> use and 2*9 = 18 iTDs on the free list.  By the time each URB
> completes, it should have released all 9 iTDs back to the free list,
> and each time an URB is submitted, it should be able to acquire all 9
> of the iTDs that it needs from the free list -- it shouldn't have to 
> allocate any from the DMA pool.
> 
> Looks like you'll have to investigate what's going on inside
> itd_urb_transaction().  Print out some useful information whenever the
> size of stream->free_list is above 50, such as the value of num_itds,
> how many of the loop iterations could get an iTD from the free list,
> and the value of itd->frame in the case where the "goto alloc_itd"
> statement is followed.
> 
> It might be a good idea also to print out the size of the free list in
> itd_complete(), where it calls ehci_urb_done(), and include the value
> of ehci->now_frame.

One thing I forgot to mention: It would help to have millisecond
precision for the timestamps in the system log, for comparison of frame
number values.  Please enable CONFIG_PRINTK_TIME for the next test.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

[-- Attachment #1: Type: text/plain, Size: 2082 bytes --]

On 03/17/13 18:36, Alan Stern wrote:
> On Sun, 17 Mar 2013, Soeren Moch wrote:
>
>> For each device only one isochronous endpoint is used (EP IN4, 1x 940
>> Bytes, Interval 1).
>> When the ENOMEM error occurs, a huge number of iTDs is in the free_list
>> of one stream. This number is much higher than the 2*M entries, which
>> should be there according to your description.
>
> Okay, but how did they get there?  With each URB requiring 9 iTDs, and
> about 5 URBs active at any time, there should be about 5*9 = 45 iTDs in
> use and 2*9 = 18 iTDs on the free list.  By the time each URB
> completes, it should have released all 9 iTDs back to the free list,
> and each time an URB is submitted, it should be able to acquire all 9
> of the iTDs that it needs from the free list -- it shouldn't have to
> allocate any from the DMA pool.
>
> Looks like you'll have to investigate what's going on inside
> itd_urb_transaction().  Print out some useful information whenever the
> size of stream->free_list is above 50, such as the value of num_itds,
> how many of the loop iterations could get an iTD from the free list,
> and the value of itd->frame in the case where the "goto alloc_itd"
> statement is followed.
>
> It might be a good idea also to print out the size of the free list in
> itd_complete(), where it calls ehci_urb_done(), and include the value
> of ehci->now_frame.
>

Now I found out what is going on here:

In itd_urb_transaction() we allocate 9 iTDs for each URB with 
number_of_packets == 64 in my case. The iTDs are added to 
sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th 
one is released back to the front of the streams free_list in 
iso_sched_free(). This iTD was cleared after allocation and has a frame 
number of 0 now. So for each allocation when now_frame == 0 we allocate 
from the dma_pool, not from the free_list. The attached patch 
invalidates the frame number in each iTD before it is sent to the 
scheduler. This fixes the problem without the need to iterate over a iTD 
list.

Signed-off-by: Soeren Moch <smoch@web.de>




[-- Attachment #2: ehci.diff --]
[-- Type: text/x-patch, Size: 603 bytes --]

--- linux-3.9.0-rc3-guru/drivers/usb/host/ehci-sched.c.orig	2013-03-21 17:36:21.000000000 +0100
+++ linux-3.9.0-rc3-guru/drivers/usb/host/ehci-sched.c	2013-03-21 17:38:56.000000000 +0100
@@ -1214,6 +1214,7 @@ itd_urb_transaction (
 
 		memset (itd, 0, sizeof *itd);
 		itd->itd_dma = itd_dma;
+		itd->frame = -1;
 		list_add (&itd->itd_list, &sched->td_list);
 	}
 	spin_unlock_irqrestore (&ehci->lock, flags);
@@ -1915,6 +1916,7 @@ sitd_urb_transaction (
 
 		memset (sitd, 0, sizeof *sitd);
 		sitd->sitd_dma = sitd_dma;
+		sitd->frame = -1;
 		list_add (&sitd->sitd_list, &iso_sched->td_list);
 	}
 

[PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 03/17/13 18:36, Alan Stern wrote:
> On Sun, 17 Mar 2013, Soeren Moch wrote:
>
>> For each device only one isochronous endpoint is used (EP IN4, 1x 940
>> Bytes, Interval 1).
>> When the ENOMEM error occurs, a huge number of iTDs is in the free_list
>> of one stream. This number is much higher than the 2*M entries, which
>> should be there according to your description.
>
> Okay, but how did they get there?  With each URB requiring 9 iTDs, and
> about 5 URBs active at any time, there should be about 5*9 = 45 iTDs in
> use and 2*9 = 18 iTDs on the free list.  By the time each URB
> completes, it should have released all 9 iTDs back to the free list,
> and each time an URB is submitted, it should be able to acquire all 9
> of the iTDs that it needs from the free list -- it shouldn't have to
> allocate any from the DMA pool.
>
> Looks like you'll have to investigate what's going on inside
> itd_urb_transaction().  Print out some useful information whenever the
> size of stream->free_list is above 50, such as the value of num_itds,
> how many of the loop iterations could get an iTD from the free list,
> and the value of itd->frame in the case where the "goto alloc_itd"
> statement is followed.
>
> It might be a good idea also to print out the size of the free list in
> itd_complete(), where it calls ehci_urb_done(), and include the value
> of ehci->now_frame.
>

Now I found out what is going on here:

In itd_urb_transaction() we allocate 9 iTDs for each URB with 
number_of_packets == 64 in my case. The iTDs are added to 
sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th 
one is released back to the front of the streams free_list in 
iso_sched_free(). This iTD was cleared after allocation and has a frame 
number of 0 now. So for each allocation when now_frame == 0 we allocate 
from the dma_pool, not from the free_list. The attached patch 
invalidates the frame number in each iTD before it is sent to the 
scheduler. This fixes the problem without the need to iterate over a iTD 
list.

Signed-off-by: Soeren Moch <smoch@web.de>



-------------- next part --------------
A non-text attachment was scrubbed...
Name: ehci.diff
Type: text/x-patch
Size: 603 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20130321/5c488fe2/attachment.bin>

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Jason Cooper]

On Thu, Mar 21, 2013 at 06:04:59PM +0100, Soeren Moch wrote:
> On 03/17/13 18:36, Alan Stern wrote:
> >On Sun, 17 Mar 2013, Soeren Moch wrote:
> >
> >>For each device only one isochronous endpoint is used (EP IN4, 1x 940
> >>Bytes, Interval 1).
> >>When the ENOMEM error occurs, a huge number of iTDs is in the free_list
> >>of one stream. This number is much higher than the 2*M entries, which
> >>should be there according to your description.
> >
> >Okay, but how did they get there?  With each URB requiring 9 iTDs, and
> >about 5 URBs active at any time, there should be about 5*9 = 45 iTDs in
> >use and 2*9 = 18 iTDs on the free list.  By the time each URB
> >completes, it should have released all 9 iTDs back to the free list,
> >and each time an URB is submitted, it should be able to acquire all 9
> >of the iTDs that it needs from the free list -- it shouldn't have to
> >allocate any from the DMA pool.
> >
> >Looks like you'll have to investigate what's going on inside
> >itd_urb_transaction().  Print out some useful information whenever the
> >size of stream->free_list is above 50, such as the value of num_itds,
> >how many of the loop iterations could get an iTD from the free list,
> >and the value of itd->frame in the case where the "goto alloc_itd"
> >statement is followed.
> >
> >It might be a good idea also to print out the size of the free list in
> >itd_complete(), where it calls ehci_urb_done(), and include the value
> >of ehci->now_frame.
> >
> 
> Now I found out what is going on here:
> 
> In itd_urb_transaction() we allocate 9 iTDs for each URB with
> number_of_packets == 64 in my case. The iTDs are added to
> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the
> 9th one is released back to the front of the streams free_list in
> iso_sched_free(). This iTD was cleared after allocation and has a
> frame number of 0 now. So for each allocation when now_frame == 0 we
> allocate from the dma_pool, not from the free_list. The attached
> patch invalidates the frame number in each iTD before it is sent to
> the scheduler. This fixes the problem without the need to iterate
> over a iTD list.
> 
> Signed-off-by: Soeren Moch <smoch@web.de>

Wow!  Great work Soeren!  Talk about a long road to a small fix.  Thanks
for keeping after it.

thx,

Jason.

> 
> 
> 

> --- linux-3.9.0-rc3-guru/drivers/usb/host/ehci-sched.c.orig	2013-03-21 17:36:21.000000000 +0100
> +++ linux-3.9.0-rc3-guru/drivers/usb/host/ehci-sched.c	2013-03-21 17:38:56.000000000 +0100
> @@ -1214,6 +1214,7 @@ itd_urb_transaction (
>  
>  		memset (itd, 0, sizeof *itd);
>  		itd->itd_dma = itd_dma;
> +		itd->frame = -1;
>  		list_add (&itd->itd_list, &sched->td_list);
>  	}
>  	spin_unlock_irqrestore (&ehci->lock, flags);
> @@ -1915,6 +1916,7 @@ sitd_urb_transaction (
>  
>  		memset (sitd, 0, sizeof *sitd);
>  		sitd->sitd_dma = sitd_dma;
> +		sitd->frame = -1;
>  		list_add (&sitd->sitd_list, &iso_sched->td_list);
>  	}
>  

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Jason Cooper]

On Thu, Mar 21, 2013 at 06:04:59PM +0100, Soeren Moch wrote:
> On 03/17/13 18:36, Alan Stern wrote:
> >On Sun, 17 Mar 2013, Soeren Moch wrote:
> >
> >>For each device only one isochronous endpoint is used (EP IN4, 1x 940
> >>Bytes, Interval 1).
> >>When the ENOMEM error occurs, a huge number of iTDs is in the free_list
> >>of one stream. This number is much higher than the 2*M entries, which
> >>should be there according to your description.
> >
> >Okay, but how did they get there?  With each URB requiring 9 iTDs, and
> >about 5 URBs active at any time, there should be about 5*9 = 45 iTDs in
> >use and 2*9 = 18 iTDs on the free list.  By the time each URB
> >completes, it should have released all 9 iTDs back to the free list,
> >and each time an URB is submitted, it should be able to acquire all 9
> >of the iTDs that it needs from the free list -- it shouldn't have to
> >allocate any from the DMA pool.
> >
> >Looks like you'll have to investigate what's going on inside
> >itd_urb_transaction().  Print out some useful information whenever the
> >size of stream->free_list is above 50, such as the value of num_itds,
> >how many of the loop iterations could get an iTD from the free list,
> >and the value of itd->frame in the case where the "goto alloc_itd"
> >statement is followed.
> >
> >It might be a good idea also to print out the size of the free list in
> >itd_complete(), where it calls ehci_urb_done(), and include the value
> >of ehci->now_frame.
> >
> 
> Now I found out what is going on here:
> 
> In itd_urb_transaction() we allocate 9 iTDs for each URB with
> number_of_packets == 64 in my case. The iTDs are added to
> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the
> 9th one is released back to the front of the streams free_list in
> iso_sched_free(). This iTD was cleared after allocation and has a
> frame number of 0 now. So for each allocation when now_frame == 0 we
> allocate from the dma_pool, not from the free_list. The attached
> patch invalidates the frame number in each iTD before it is sent to
> the scheduler. This fixes the problem without the need to iterate
> over a iTD list.
> 
> Signed-off-by: Soeren Moch <smoch@web.de>

Wow!  Great work Soeren!  Talk about a long road to a small fix.  Thanks
for keeping after it.

thx,

Jason.

> 
> 
> 

> --- linux-3.9.0-rc3-guru/drivers/usb/host/ehci-sched.c.orig	2013-03-21 17:36:21.000000000 +0100
> +++ linux-3.9.0-rc3-guru/drivers/usb/host/ehci-sched.c	2013-03-21 17:38:56.000000000 +0100
> @@ -1214,6 +1214,7 @@ itd_urb_transaction (
>  
>  		memset (itd, 0, sizeof *itd);
>  		itd->itd_dma = itd_dma;
> +		itd->frame = -1;
>  		list_add (&itd->itd_list, &sched->td_list);
>  	}
>  	spin_unlock_irqrestore (&ehci->lock, flags);
> @@ -1915,6 +1916,7 @@ sitd_urb_transaction (
>  
>  		memset (sitd, 0, sizeof *sitd);
>  		sitd->sitd_dma = sitd_dma;
> +		sitd->frame = -1;
>  		list_add (&sitd->sitd_list, &iso_sched->td_list);
>  	}
>  

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Jason Cooper]

On Thu, Mar 21, 2013 at 06:04:59PM +0100, Soeren Moch wrote:
> On 03/17/13 18:36, Alan Stern wrote:
> >On Sun, 17 Mar 2013, Soeren Moch wrote:
> >
> >>For each device only one isochronous endpoint is used (EP IN4, 1x 940
> >>Bytes, Interval 1).
> >>When the ENOMEM error occurs, a huge number of iTDs is in the free_list
> >>of one stream. This number is much higher than the 2*M entries, which
> >>should be there according to your description.
> >
> >Okay, but how did they get there?  With each URB requiring 9 iTDs, and
> >about 5 URBs active at any time, there should be about 5*9 = 45 iTDs in
> >use and 2*9 = 18 iTDs on the free list.  By the time each URB
> >completes, it should have released all 9 iTDs back to the free list,
> >and each time an URB is submitted, it should be able to acquire all 9
> >of the iTDs that it needs from the free list -- it shouldn't have to
> >allocate any from the DMA pool.
> >
> >Looks like you'll have to investigate what's going on inside
> >itd_urb_transaction().  Print out some useful information whenever the
> >size of stream->free_list is above 50, such as the value of num_itds,
> >how many of the loop iterations could get an iTD from the free list,
> >and the value of itd->frame in the case where the "goto alloc_itd"
> >statement is followed.
> >
> >It might be a good idea also to print out the size of the free list in
> >itd_complete(), where it calls ehci_urb_done(), and include the value
> >of ehci->now_frame.
> >
> 
> Now I found out what is going on here:
> 
> In itd_urb_transaction() we allocate 9 iTDs for each URB with
> number_of_packets == 64 in my case. The iTDs are added to
> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the
> 9th one is released back to the front of the streams free_list in
> iso_sched_free(). This iTD was cleared after allocation and has a
> frame number of 0 now. So for each allocation when now_frame == 0 we
> allocate from the dma_pool, not from the free_list. The attached
> patch invalidates the frame number in each iTD before it is sent to
> the scheduler. This fixes the problem without the need to iterate
> over a iTD list.
> 
> Signed-off-by: Soeren Moch <smoch@web.de>

Wow!  Great work Soeren!  Talk about a long road to a small fix.  Thanks
for keeping after it.

thx,

Jason.

> 
> 
> 

> --- linux-3.9.0-rc3-guru/drivers/usb/host/ehci-sched.c.orig	2013-03-21 17:36:21.000000000 +0100
> +++ linux-3.9.0-rc3-guru/drivers/usb/host/ehci-sched.c	2013-03-21 17:38:56.000000000 +0100
> @@ -1214,6 +1214,7 @@ itd_urb_transaction (
>  
>  		memset (itd, 0, sizeof *itd);
>  		itd->itd_dma = itd_dma;
> +		itd->frame = -1;
>  		list_add (&itd->itd_list, &sched->td_list);
>  	}
>  	spin_unlock_irqrestore (&ehci->lock, flags);
> @@ -1915,6 +1916,7 @@ sitd_urb_transaction (
>  
>  		memset (sitd, 0, sizeof *sitd);
>  		sitd->sitd_dma = sitd_dma;
> +		sitd->frame = -1;
>  		list_add (&sitd->sitd_list, &iso_sched->td_list);
>  	}
>  

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Arnd Bergmann]

On Thursday 21 March 2013, Jason Cooper wrote:
> On Thu, Mar 21, 2013 at 06:04:59PM +0100, Soeren Moch wrote:

> > 
> > Now I found out what is going on here:
> > 
> > In itd_urb_transaction() we allocate 9 iTDs for each URB with
> > number_of_packets == 64 in my case. The iTDs are added to
> > sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the
> > 9th one is released back to the front of the streams free_list in
> > iso_sched_free(). This iTD was cleared after allocation and has a
> > frame number of 0 now. So for each allocation when now_frame == 0 we
> > allocate from the dma_pool, not from the free_list. The attached
> > patch invalidates the frame number in each iTD before it is sent to
> > the scheduler. This fixes the problem without the need to iterate
> > over a iTD list.
> > 
> > Signed-off-by: Soeren Moch <smoch@web.de>
> 
> Wow!  Great work Soeren!  Talk about a long road to a small fix.  Thanks
> for keeping after it.

+1

I hardly understand half of the description above, but that much sounds
plausible. Is this a bug fix that should get backported to stable kernels?

	Arnd

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Arnd Bergmann]

On Thursday 21 March 2013, Jason Cooper wrote:
> On Thu, Mar 21, 2013 at 06:04:59PM +0100, Soeren Moch wrote:

> > 
> > Now I found out what is going on here:
> > 
> > In itd_urb_transaction() we allocate 9 iTDs for each URB with
> > number_of_packets == 64 in my case. The iTDs are added to
> > sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the
> > 9th one is released back to the front of the streams free_list in
> > iso_sched_free(). This iTD was cleared after allocation and has a
> > frame number of 0 now. So for each allocation when now_frame == 0 we
> > allocate from the dma_pool, not from the free_list. The attached
> > patch invalidates the frame number in each iTD before it is sent to
> > the scheduler. This fixes the problem without the need to iterate
> > over a iTD list.
> > 
> > Signed-off-by: Soeren Moch <smoch@web.de>
> 
> Wow!  Great work Soeren!  Talk about a long road to a small fix.  Thanks
> for keeping after it.

+1

I hardly understand half of the description above, but that much sounds
plausible. Is this a bug fix that should get backported to stable kernels?

	Arnd

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Arnd Bergmann]

On Thursday 21 March 2013, Jason Cooper wrote:
> On Thu, Mar 21, 2013 at 06:04:59PM +0100, Soeren Moch wrote:

> > 
> > Now I found out what is going on here:
> > 
> > In itd_urb_transaction() we allocate 9 iTDs for each URB with
> > number_of_packets == 64 in my case. The iTDs are added to
> > sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the
> > 9th one is released back to the front of the streams free_list in
> > iso_sched_free(). This iTD was cleared after allocation and has a
> > frame number of 0 now. So for each allocation when now_frame == 0 we
> > allocate from the dma_pool, not from the free_list. The attached
> > patch invalidates the frame number in each iTD before it is sent to
> > the scheduler. This fixes the problem without the need to iterate
> > over a iTD list.
> > 
> > Signed-off-by: Soeren Moch <smoch@web.de>
> 
> Wow!  Great work Soeren!  Talk about a long road to a small fix.  Thanks
> for keeping after it.

+1

I hardly understand half of the description above, but that much sounds
plausible. Is this a bug fix that should get backported to stable kernels?

	Arnd

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Michael Trimarchi]

Hi

On 21/03/13 20:10, Arnd Bergmann wrote:
> On Thursday 21 March 2013, Jason Cooper wrote:
>> On Thu, Mar 21, 2013 at 06:04:59PM +0100, Soeren Moch wrote:
> 
>>>
>>> Now I found out what is going on here:
>>>
>>> In itd_urb_transaction() we allocate 9 iTDs for each URB with
>>> number_of_packets == 64 in my case. The iTDs are added to
>>> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the
>>> 9th one is released back to the front of the streams free_list in
>>> iso_sched_free(). This iTD was cleared after allocation and has a
>>> frame number of 0 now. So for each allocation when now_frame == 0 we
>>> allocate from the dma_pool, not from the free_list. The attached
>>> patch invalidates the frame number in each iTD before it is sent to
>>> the scheduler. This fixes the problem without the need to iterate
>>> over a iTD list.
>>>
>>> Signed-off-by: Soeren Moch <smoch@web.de>
>>
>> Wow!  Great work Soeren!  Talk about a long road to a small fix.  Thanks
>> for keeping after it.
> 
> +1
> 
> I hardly understand half of the description above, but that much sounds
> plausible. Is this a bug fix that should get backported to stable kernels?
> 

+ 1
and I can test on my device. Just one comment:
I don't know if -1 is the correct way to init it.

Michael

> 	Arnd
> 

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Michael Trimarchi]

Hi

On 21/03/13 20:10, Arnd Bergmann wrote:
> On Thursday 21 March 2013, Jason Cooper wrote:
>> On Thu, Mar 21, 2013 at 06:04:59PM +0100, Soeren Moch wrote:
> 
>>>
>>> Now I found out what is going on here:
>>>
>>> In itd_urb_transaction() we allocate 9 iTDs for each URB with
>>> number_of_packets == 64 in my case. The iTDs are added to
>>> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the
>>> 9th one is released back to the front of the streams free_list in
>>> iso_sched_free(). This iTD was cleared after allocation and has a
>>> frame number of 0 now. So for each allocation when now_frame == 0 we
>>> allocate from the dma_pool, not from the free_list. The attached
>>> patch invalidates the frame number in each iTD before it is sent to
>>> the scheduler. This fixes the problem without the need to iterate
>>> over a iTD list.
>>>
>>> Signed-off-by: Soeren Moch <smoch@web.de>
>>
>> Wow!  Great work Soeren!  Talk about a long road to a small fix.  Thanks
>> for keeping after it.
> 
> +1
> 
> I hardly understand half of the description above, but that much sounds
> plausible. Is this a bug fix that should get backported to stable kernels?
> 

+ 1
and I can test on my device. Just one comment:
I don't know if -1 is the correct way to init it.

Michael

> 	Arnd
> 

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Michael Trimarchi]

Hi

On 21/03/13 20:10, Arnd Bergmann wrote:
> On Thursday 21 March 2013, Jason Cooper wrote:
>> On Thu, Mar 21, 2013 at 06:04:59PM +0100, Soeren Moch wrote:
> 
>>>
>>> Now I found out what is going on here:
>>>
>>> In itd_urb_transaction() we allocate 9 iTDs for each URB with
>>> number_of_packets == 64 in my case. The iTDs are added to
>>> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the
>>> 9th one is released back to the front of the streams free_list in
>>> iso_sched_free(). This iTD was cleared after allocation and has a
>>> frame number of 0 now. So for each allocation when now_frame == 0 we
>>> allocate from the dma_pool, not from the free_list. The attached
>>> patch invalidates the frame number in each iTD before it is sent to
>>> the scheduler. This fixes the problem without the need to iterate
>>> over a iTD list.
>>>
>>> Signed-off-by: Soeren Moch <smoch@web.de>
>>
>> Wow!  Great work Soeren!  Talk about a long road to a small fix.  Thanks
>> for keeping after it.
> 
> +1
> 
> I hardly understand half of the description above, but that much sounds
> plausible. Is this a bug fix that should get backported to stable kernels?
> 

+ 1
and I can test on my device. Just one comment:
I don't know if -1 is the correct way to init it.

Michael

> 	Arnd
> 

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Thu, 21 Mar 2013, Soeren Moch wrote:

> Now I found out what is going on here:
> 
> In itd_urb_transaction() we allocate 9 iTDs for each URB with 
> number_of_packets == 64 in my case. The iTDs are added to 
> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th 
> one is released back to the front of the streams free_list in 
> iso_sched_free(). This iTD was cleared after allocation and has a frame 
> number of 0 now. So for each allocation when now_frame == 0 we allocate 
> from the dma_pool, not from the free_list.

Okay, that is a problem.  But it shouldn't be such a big problem,
because now_frame should not be equal to 0 very often.

>  The attached patch 
> invalidates the frame number in each iTD before it is sent to the 
> scheduler. This fixes the problem without the need to iterate over a iTD 
> list.

The patch looks okay.  However I would like to understand why the 0 
frame value messes things up so much.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Thu, 21 Mar 2013, Soeren Moch wrote:

> Now I found out what is going on here:
> 
> In itd_urb_transaction() we allocate 9 iTDs for each URB with 
> number_of_packets == 64 in my case. The iTDs are added to 
> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th 
> one is released back to the front of the streams free_list in 
> iso_sched_free(). This iTD was cleared after allocation and has a frame 
> number of 0 now. So for each allocation when now_frame == 0 we allocate 
> from the dma_pool, not from the free_list.

Okay, that is a problem.  But it shouldn't be such a big problem,
because now_frame should not be equal to 0 very often.

>  The attached patch 
> invalidates the frame number in each iTD before it is sent to the 
> scheduler. This fixes the problem without the need to iterate over a iTD 
> list.

The patch looks okay.  However I would like to understand why the 0 
frame value messes things up so much.

Alan Stern

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Thu, 21 Mar 2013, Soeren Moch wrote:

> Now I found out what is going on here:
> 
> In itd_urb_transaction() we allocate 9 iTDs for each URB with 
> number_of_packets == 64 in my case. The iTDs are added to 
> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th 
> one is released back to the front of the streams free_list in 
> iso_sched_free(). This iTD was cleared after allocation and has a frame 
> number of 0 now. So for each allocation when now_frame == 0 we allocate 
> from the dma_pool, not from the free_list.

Okay, that is a problem.  But it shouldn't be such a big problem,
because now_frame should not be equal to 0 very often.

>  The attached patch 
> invalidates the frame number in each iTD before it is sent to the 
> scheduler. This fixes the problem without the need to iterate over a iTD 
> list.

The patch looks okay.  However I would like to understand why the 0 
frame value messes things up so much.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Thu, 21 Mar 2013, Alan Stern wrote:

> On Thu, 21 Mar 2013, Soeren Moch wrote:
> 
> > Now I found out what is going on here:
> > 
> > In itd_urb_transaction() we allocate 9 iTDs for each URB with 
> > number_of_packets == 64 in my case. The iTDs are added to 
> > sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th 
> > one is released back to the front of the streams free_list in 
> > iso_sched_free(). This iTD was cleared after allocation and has a frame 
> > number of 0 now. So for each allocation when now_frame == 0 we allocate 
> > from the dma_pool, not from the free_list.
> 
> Okay, that is a problem.  But it shouldn't be such a big problem,
> because now_frame should not be equal to 0 very often.

Oh, wait, now I get it.  We never reach a steady state, because the
free list never shrinks, but occasionally it does increase when
now_frame is equal to 0.  Even though that doesn't happen very often,
the effects add up.

Very good; tomorrow I will send your patch in.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Thu, 21 Mar 2013, Alan Stern wrote:

> On Thu, 21 Mar 2013, Soeren Moch wrote:
> 
> > Now I found out what is going on here:
> > 
> > In itd_urb_transaction() we allocate 9 iTDs for each URB with 
> > number_of_packets == 64 in my case. The iTDs are added to 
> > sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th 
> > one is released back to the front of the streams free_list in 
> > iso_sched_free(). This iTD was cleared after allocation and has a frame 
> > number of 0 now. So for each allocation when now_frame == 0 we allocate 
> > from the dma_pool, not from the free_list.
> 
> Okay, that is a problem.  But it shouldn't be such a big problem,
> because now_frame should not be equal to 0 very often.

Oh, wait, now I get it.  We never reach a steady state, because the
free list never shrinks, but occasionally it does increase when
now_frame is equal to 0.  Even though that doesn't happen very often,
the effects add up.

Very good; tomorrow I will send your patch in.

Alan Stern

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Thu, 21 Mar 2013, Alan Stern wrote:

> On Thu, 21 Mar 2013, Soeren Moch wrote:
> 
> > Now I found out what is going on here:
> > 
> > In itd_urb_transaction() we allocate 9 iTDs for each URB with 
> > number_of_packets == 64 in my case. The iTDs are added to 
> > sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th 
> > one is released back to the front of the streams free_list in 
> > iso_sched_free(). This iTD was cleared after allocation and has a frame 
> > number of 0 now. So for each allocation when now_frame == 0 we allocate 
> > from the dma_pool, not from the free_list.
> 
> Okay, that is a problem.  But it shouldn't be such a big problem,
> because now_frame should not be equal to 0 very often.

Oh, wait, now I get it.  We never reach a steady state, because the
free list never shrinks, but occasionally it does increase when
now_frame is equal to 0.  Even though that doesn't happen very often,
the effects add up.

Very good; tomorrow I will send your patch in.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Andrew Lunn]

On Thu, Mar 21, 2013 at 05:12:01PM -0400, Alan Stern wrote:
> On Thu, 21 Mar 2013, Alan Stern wrote:
> 
> > On Thu, 21 Mar 2013, Soeren Moch wrote:
> > 
> > > Now I found out what is going on here:
> > > 
> > > In itd_urb_transaction() we allocate 9 iTDs for each URB with 
> > > number_of_packets == 64 in my case. The iTDs are added to 
> > > sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th 
> > > one is released back to the front of the streams free_list in 
> > > iso_sched_free(). This iTD was cleared after allocation and has a frame 
> > > number of 0 now. So for each allocation when now_frame == 0 we allocate 
> > > from the dma_pool, not from the free_list.
> > 
> > Okay, that is a problem.  But it shouldn't be such a big problem,
> > because now_frame should not be equal to 0 very often.
> 
> Oh, wait, now I get it.  We never reach a steady state, because the
> free list never shrinks, but occasionally it does increase when
> now_frame is equal to 0.  Even though that doesn't happen very often,
> the effects add up.
> 
> Very good; tomorrow I will send your patch in.

Hi Alan, Soeren

Could you word the description a bit better. If Alan did not get it
without a bit of thought, few others are going to understand it
without a better explanation.

Thanks
	Andrew

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Andrew Lunn]

On Thu, Mar 21, 2013 at 05:12:01PM -0400, Alan Stern wrote:
> On Thu, 21 Mar 2013, Alan Stern wrote:
> 
> > On Thu, 21 Mar 2013, Soeren Moch wrote:
> > 
> > > Now I found out what is going on here:
> > > 
> > > In itd_urb_transaction() we allocate 9 iTDs for each URB with 
> > > number_of_packets == 64 in my case. The iTDs are added to 
> > > sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th 
> > > one is released back to the front of the streams free_list in 
> > > iso_sched_free(). This iTD was cleared after allocation and has a frame 
> > > number of 0 now. So for each allocation when now_frame == 0 we allocate 
> > > from the dma_pool, not from the free_list.
> > 
> > Okay, that is a problem.  But it shouldn't be such a big problem,
> > because now_frame should not be equal to 0 very often.
> 
> Oh, wait, now I get it.  We never reach a steady state, because the
> free list never shrinks, but occasionally it does increase when
> now_frame is equal to 0.  Even though that doesn't happen very often,
> the effects add up.
> 
> Very good; tomorrow I will send your patch in.

Hi Alan, Soeren

Could you word the description a bit better. If Alan did not get it
without a bit of thought, few others are going to understand it
without a better explanation.

Thanks
	Andrew

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Andrew Lunn]

On Thu, Mar 21, 2013 at 05:12:01PM -0400, Alan Stern wrote:
> On Thu, 21 Mar 2013, Alan Stern wrote:
> 
> > On Thu, 21 Mar 2013, Soeren Moch wrote:
> > 
> > > Now I found out what is going on here:
> > > 
> > > In itd_urb_transaction() we allocate 9 iTDs for each URB with 
> > > number_of_packets == 64 in my case. The iTDs are added to 
> > > sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th 
> > > one is released back to the front of the streams free_list in 
> > > iso_sched_free(). This iTD was cleared after allocation and has a frame 
> > > number of 0 now. So for each allocation when now_frame == 0 we allocate 
> > > from the dma_pool, not from the free_list.
> > 
> > Okay, that is a problem.  But it shouldn't be such a big problem,
> > because now_frame should not be equal to 0 very often.
> 
> Oh, wait, now I get it.  We never reach a steady state, because the
> free list never shrinks, but occasionally it does increase when
> now_frame is equal to 0.  Even though that doesn't happen very often,
> the effects add up.
> 
> Very good; tomorrow I will send your patch in.

Hi Alan, Soeren

Could you word the description a bit better. If Alan did not get it
without a bit of thought, few others are going to understand it
without a better explanation.

Thanks
	Andrew

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 03/21/13 22:12, Alan Stern wrote:
> On Thu, 21 Mar 2013, Alan Stern wrote:
>
>> On Thu, 21 Mar 2013, Soeren Moch wrote:
>>
>>> Now I found out what is going on here:
>>>
>>> In itd_urb_transaction() we allocate 9 iTDs for each URB with
>>> number_of_packets == 64 in my case. The iTDs are added to
>>> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th
>>> one is released back to the front of the streams free_list in
>>> iso_sched_free(). This iTD was cleared after allocation and has a frame
>>> number of 0 now. So for each allocation when now_frame == 0 we allocate
>>> from the dma_pool, not from the free_list.
>>
>> Okay, that is a problem.  But it shouldn't be such a big problem,
>> because now_frame should not be equal to 0 very often.
>
> Oh, wait, now I get it.  We never reach a steady state, because the
> free list never shrinks, but occasionally it does increase when
> now_frame is equal to 0.  Even though that doesn't happen very often,
> the effects add up.

Correct. Approximately twice a second we allocate 9 iTDs from the 
dma_pool in my case (the frame numbers run from 0 to 511 - not up to 
2047, which I thought they should). But since we allocate iTDs every 8 
frames in my case (for each active stream), the pool allocations occur 
only when we hit the allocation sequence frame 0,8,16,... (not one of 
the other 7 opportunities frame 1,9,17,... - frame 7,15,23,...)

> Very good; tomorrow I will send your patch in.
>
> Alan Stern
>
Thank you. And also thanks to all who helped to track down this issue.

  Soeren

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 03/21/13 22:12, Alan Stern wrote:
> On Thu, 21 Mar 2013, Alan Stern wrote:
>
>> On Thu, 21 Mar 2013, Soeren Moch wrote:
>>
>>> Now I found out what is going on here:
>>>
>>> In itd_urb_transaction() we allocate 9 iTDs for each URB with
>>> number_of_packets == 64 in my case. The iTDs are added to
>>> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th
>>> one is released back to the front of the streams free_list in
>>> iso_sched_free(). This iTD was cleared after allocation and has a frame
>>> number of 0 now. So for each allocation when now_frame == 0 we allocate
>>> from the dma_pool, not from the free_list.
>>
>> Okay, that is a problem.  But it shouldn't be such a big problem,
>> because now_frame should not be equal to 0 very often.
>
> Oh, wait, now I get it.  We never reach a steady state, because the
> free list never shrinks, but occasionally it does increase when
> now_frame is equal to 0.  Even though that doesn't happen very often,
> the effects add up.

Correct. Approximately twice a second we allocate 9 iTDs from the 
dma_pool in my case (the frame numbers run from 0 to 511 - not up to 
2047, which I thought they should). But since we allocate iTDs every 8 
frames in my case (for each active stream), the pool allocations occur 
only when we hit the allocation sequence frame 0,8,16,... (not one of 
the other 7 opportunities frame 1,9,17,... - frame 7,15,23,...)

> Very good; tomorrow I will send your patch in.
>
> Alan Stern
>
Thank you. And also thanks to all who helped to track down this issue.

  Soeren

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 03/21/13 22:12, Alan Stern wrote:
> On Thu, 21 Mar 2013, Alan Stern wrote:
>
>> On Thu, 21 Mar 2013, Soeren Moch wrote:
>>
>>> Now I found out what is going on here:
>>>
>>> In itd_urb_transaction() we allocate 9 iTDs for each URB with
>>> number_of_packets == 64 in my case. The iTDs are added to
>>> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th
>>> one is released back to the front of the streams free_list in
>>> iso_sched_free(). This iTD was cleared after allocation and has a frame
>>> number of 0 now. So for each allocation when now_frame == 0 we allocate
>>> from the dma_pool, not from the free_list.
>>
>> Okay, that is a problem.  But it shouldn't be such a big problem,
>> because now_frame should not be equal to 0 very often.
>
> Oh, wait, now I get it.  We never reach a steady state, because the
> free list never shrinks, but occasionally it does increase when
> now_frame is equal to 0.  Even though that doesn't happen very often,
> the effects add up.

Correct. Approximately twice a second we allocate 9 iTDs from the 
dma_pool in my case (the frame numbers run from 0 to 511 - not up to 
2047, which I thought they should). But since we allocate iTDs every 8 
frames in my case (for each active stream), the pool allocations occur 
only when we hit the allocation sequence frame 0,8,16,... (not one of 
the other 7 opportunities frame 1,9,17,... - frame 7,15,23,...)

> Very good; tomorrow I will send your patch in.
>
> Alan Stern
>
Thank you. And also thanks to all who helped to track down this issue.

  Soeren

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 21.03.2013 20:10, Arnd Bergmann wrote:
> On Thursday 21 March 2013, Jason Cooper wrote:
>> On Thu, Mar 21, 2013 at 06:04:59PM +0100, Soeren Moch wrote:
>
>>>
>>> Now I found out what is going on here:
>>>
>>> In itd_urb_transaction() we allocate 9 iTDs for each URB with
>>> number_of_packets == 64 in my case. The iTDs are added to
>>> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the
>>> 9th one is released back to the front of the streams free_list in
>>> iso_sched_free(). This iTD was cleared after allocation and has a
>>> frame number of 0 now. So for each allocation when now_frame == 0 we
>>> allocate from the dma_pool, not from the free_list. The attached
>>> patch invalidates the frame number in each iTD before it is sent to
>>> the scheduler. This fixes the problem without the need to iterate
>>> over a iTD list.
>>>
>>> Signed-off-by: Soeren Moch <smoch@web.de>
>>
>> Wow!  Great work Soeren!  Talk about a long road to a small fix.  Thanks
>> for keeping after it.
>
> +1
>
> I hardly understand half of the description above, but that much sounds
> plausible. Is this a bug fix that should get backported to stable kernels?
>
> 	Arnd
>
I think this patch should go to stable kernels, too. But I'm not an 
expert here...

   Soeren

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 21.03.2013 20:10, Arnd Bergmann wrote:
> On Thursday 21 March 2013, Jason Cooper wrote:
>> On Thu, Mar 21, 2013 at 06:04:59PM +0100, Soeren Moch wrote:
>
>>>
>>> Now I found out what is going on here:
>>>
>>> In itd_urb_transaction() we allocate 9 iTDs for each URB with
>>> number_of_packets == 64 in my case. The iTDs are added to
>>> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the
>>> 9th one is released back to the front of the streams free_list in
>>> iso_sched_free(). This iTD was cleared after allocation and has a
>>> frame number of 0 now. So for each allocation when now_frame == 0 we
>>> allocate from the dma_pool, not from the free_list. The attached
>>> patch invalidates the frame number in each iTD before it is sent to
>>> the scheduler. This fixes the problem without the need to iterate
>>> over a iTD list.
>>>
>>> Signed-off-by: Soeren Moch <smoch@web.de>
>>
>> Wow!  Great work Soeren!  Talk about a long road to a small fix.  Thanks
>> for keeping after it.
>
> +1
>
> I hardly understand half of the description above, but that much sounds
> plausible. Is this a bug fix that should get backported to stable kernels?
>
> 	Arnd
>
I think this patch should go to stable kernels, too. But I'm not an 
expert here...

   Soeren

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 21.03.2013 20:10, Arnd Bergmann wrote:
> On Thursday 21 March 2013, Jason Cooper wrote:
>> On Thu, Mar 21, 2013 at 06:04:59PM +0100, Soeren Moch wrote:
>
>>>
>>> Now I found out what is going on here:
>>>
>>> In itd_urb_transaction() we allocate 9 iTDs for each URB with
>>> number_of_packets == 64 in my case. The iTDs are added to
>>> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the
>>> 9th one is released back to the front of the streams free_list in
>>> iso_sched_free(). This iTD was cleared after allocation and has a
>>> frame number of 0 now. So for each allocation when now_frame == 0 we
>>> allocate from the dma_pool, not from the free_list. The attached
>>> patch invalidates the frame number in each iTD before it is sent to
>>> the scheduler. This fixes the problem without the need to iterate
>>> over a iTD list.
>>>
>>> Signed-off-by: Soeren Moch <smoch@web.de>
>>
>> Wow!  Great work Soeren!  Talk about a long road to a small fix.  Thanks
>> for keeping after it.
>
> +1
>
> I hardly understand half of the description above, but that much sounds
> plausible. Is this a bug fix that should get backported to stable kernels?
>
> 	Arnd
>
I think this patch should go to stable kernels, too. But I'm not an 
expert here...

   Soeren

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 21.03.2013 22:20, Andrew Lunn wrote:
> On Thu, Mar 21, 2013 at 05:12:01PM -0400, Alan Stern wrote:
>> On Thu, 21 Mar 2013, Alan Stern wrote:
>>
>>> On Thu, 21 Mar 2013, Soeren Moch wrote:
>>>
>>>> Now I found out what is going on here:
>>>>
>>>> In itd_urb_transaction() we allocate 9 iTDs for each URB with
>>>> number_of_packets == 64 in my case. The iTDs are added to
>>>> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th
>>>> one is released back to the front of the streams free_list in
>>>> iso_sched_free(). This iTD was cleared after allocation and has a frame
>>>> number of 0 now. So for each allocation when now_frame == 0 we allocate
>>>> from the dma_pool, not from the free_list.
>>>
>>> Okay, that is a problem.  But it shouldn't be such a big problem,
>>> because now_frame should not be equal to 0 very often.
>>
>> Oh, wait, now I get it.  We never reach a steady state, because the
>> free list never shrinks, but occasionally it does increase when
>> now_frame is equal to 0.  Even though that doesn't happen very often,
>> the effects add up.
>>
>> Very good; tomorrow I will send your patch in.
>
> Hi Alan, Soeren
>
> Could you word the description a bit better. If Alan did not get it
> without a bit of thought, few others are going to understand it
> without a better explanation.
>
> Thanks
> 	Andrew
>

Alan,

can you come up with a better explanation, please? I think your 
description how it is supposed to work from here
    http://marc.info/?l=linux-usb&m=136345559432055&w=2
is required to understand the problem and the fix.

Thanks,
   Soeren

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 21.03.2013 22:20, Andrew Lunn wrote:
> On Thu, Mar 21, 2013 at 05:12:01PM -0400, Alan Stern wrote:
>> On Thu, 21 Mar 2013, Alan Stern wrote:
>>
>>> On Thu, 21 Mar 2013, Soeren Moch wrote:
>>>
>>>> Now I found out what is going on here:
>>>>
>>>> In itd_urb_transaction() we allocate 9 iTDs for each URB with
>>>> number_of_packets == 64 in my case. The iTDs are added to
>>>> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th
>>>> one is released back to the front of the streams free_list in
>>>> iso_sched_free(). This iTD was cleared after allocation and has a frame
>>>> number of 0 now. So for each allocation when now_frame == 0 we allocate
>>>> from the dma_pool, not from the free_list.
>>>
>>> Okay, that is a problem.  But it shouldn't be such a big problem,
>>> because now_frame should not be equal to 0 very often.
>>
>> Oh, wait, now I get it.  We never reach a steady state, because the
>> free list never shrinks, but occasionally it does increase when
>> now_frame is equal to 0.  Even though that doesn't happen very often,
>> the effects add up.
>>
>> Very good; tomorrow I will send your patch in.
>
> Hi Alan, Soeren
>
> Could you word the description a bit better. If Alan did not get it
> without a bit of thought, few others are going to understand it
> without a better explanation.
>
> Thanks
> 	Andrew
>

Alan,

can you come up with a better explanation, please? I think your 
description how it is supposed to work from here
    http://marc.info/?l=linux-usb&m=136345559432055&w=2
is required to understand the problem and the fix.

Thanks,
   Soeren

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Soeren Moch]

On 21.03.2013 22:20, Andrew Lunn wrote:
> On Thu, Mar 21, 2013 at 05:12:01PM -0400, Alan Stern wrote:
>> On Thu, 21 Mar 2013, Alan Stern wrote:
>>
>>> On Thu, 21 Mar 2013, Soeren Moch wrote:
>>>
>>>> Now I found out what is going on here:
>>>>
>>>> In itd_urb_transaction() we allocate 9 iTDs for each URB with
>>>> number_of_packets == 64 in my case. The iTDs are added to
>>>> sched->td_list. For a frame-aligned scheduling we need 8 iTDs, the 9th
>>>> one is released back to the front of the streams free_list in
>>>> iso_sched_free(). This iTD was cleared after allocation and has a frame
>>>> number of 0 now. So for each allocation when now_frame == 0 we allocate
>>>> from the dma_pool, not from the free_list.
>>>
>>> Okay, that is a problem.  But it shouldn't be such a big problem,
>>> because now_frame should not be equal to 0 very often.
>>
>> Oh, wait, now I get it.  We never reach a steady state, because the
>> free list never shrinks, but occasionally it does increase when
>> now_frame is equal to 0.  Even though that doesn't happen very often,
>> the effects add up.
>>
>> Very good; tomorrow I will send your patch in.
>
> Hi Alan, Soeren
>
> Could you word the description a bit better. If Alan did not get it
> without a bit of thought, few others are going to understand it
> without a better explanation.
>
> Thanks
> 	Andrew
>

Alan,

can you come up with a better explanation, please? I think your 
description how it is supposed to work from here
    http://marc.info/?l=linux-usb&m=136345559432055&w=2
is required to understand the problem and the fix.

Thanks,
   Soeren

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Thu, 21 Mar 2013, Soeren Moch wrote:

> > Hi Alan, Soeren
> >
> > Could you word the description a bit better. If Alan did not get it
> > without a bit of thought, few others are going to understand it
> > without a better explanation.
> >
> > Thanks
> > 	Andrew
> >
> 
> Alan,
> 
> can you come up with a better explanation, please? I think your 
> description how it is supposed to work from here
>     http://marc.info/?l=linux-usb&m=136345559432055&w=2
> is required to understand the problem and the fix.

Okay, I will rewrite your patch description.

Alan Stern

Re: [PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Thu, 21 Mar 2013, Soeren Moch wrote:

> > Hi Alan, Soeren
> >
> > Could you word the description a bit better. If Alan did not get it
> > without a bit of thought, few others are going to understand it
> > without a better explanation.
> >
> > Thanks
> > 	Andrew
> >
> 
> Alan,
> 
> can you come up with a better explanation, please? I think your 
> description how it is supposed to work from here
>     http://marc.info/?l=linux-usb&m=136345559432055&w=2
> is required to understand the problem and the fix.

Okay, I will rewrite your patch description.

Alan Stern

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

[PATCH] USB: EHCI: fix for leaking isochronous data

[Alan Stern]

On Thu, 21 Mar 2013, Soeren Moch wrote:

> > Hi Alan, Soeren
> >
> > Could you word the description a bit better. If Alan did not get it
> > without a bit of thought, few others are going to understand it
> > without a better explanation.
> >
> > Thanks
> > 	Andrew
> >
> 
> Alan,
> 
> can you come up with a better explanation, please? I think your 
> description how it is supposed to work from here
>     http://marc.info/?l=linux-usb&m=136345559432055&w=2
> is required to understand the problem and the fix.

Okay, I will rewrite your patch description.

Alan Stern