[PATCH 0/7] add basic support for BCM6362

[PATCH 0/7] add basic support for BCM6362

[Jonas Gorski]

This patchset adds basic support for BCM6362. BCM6362 includes a 9 port
ethernet switch (4 FE PHYs, 2 RGMII ports), integrated wifi and one PCIe
port.

The first few patches do a bit of clean up first to allow the BCM6362
support code to be as small as possible.

Board definitions were left out as they are not really usable yet, and
adding DT support is planned in the future. Most code added here will
be also required with DT support.

Jonas Gorski (7):
  MIPS: BCM63XX: remove duplicate spi register definitions
  MIPS: BCM63XX: fix revision ID width
  MIPS: BCM63XX: rework chip detection
  MIPS: BCM63XX: add basic BCM6362 support
  MIPS: BCM63XX: enable SPI controller for BCM6362
  MIPS: BCM63XX: enable pcie for BCM6362
  MIPS: BCM63XX: add flash detection for BCM6362

 arch/mips/bcm63xx/Kconfig                          |    4 +
 arch/mips/bcm63xx/boards/board_bcm963xx.c          |    6 +-
 arch/mips/bcm63xx/clk.c                            |    2 +
 arch/mips/bcm63xx/cpu.c                            |  142 +++++++++++++-------
 arch/mips/bcm63xx/dev-flash.c                      |    6 +
 arch/mips/bcm63xx/dev-spi.c                        |   26 +---
 arch/mips/bcm63xx/irq.c                            |   22 +++
 arch/mips/bcm63xx/prom.c                           |    2 +
 arch/mips/bcm63xx/reset.c                          |   28 ++++
 arch/mips/bcm63xx/setup.c                          |    5 +-
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h   |  141 ++++++++++++++++++-
 .../include/asm/mach-bcm63xx/bcm63xx_dev_spi.h     |   11 +-
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h  |    2 +
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h  |  105 +++++++++------
 arch/mips/include/asm/mach-bcm63xx/ioremap.h       |    1 +
 arch/mips/pci/pci-bcm63xx.c                        |   11 +-
 16 files changed, 392 insertions(+), 122 deletions(-)

-- 
1.7.10.4

[PATCH 1/7] MIPS: BCM63XX: remove duplicate spi register definitions

[Jonas Gorski]

BCM6338 and BCM6348, and BCM6358 and everything after that share the
same register layout. To not have to redefine them for each new chip
and keep the code size small, only use the definitions for the first
chip with the certain layout.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
---
 arch/mips/bcm63xx/dev-spi.c                        |   24 +++---------
 .../include/asm/mach-bcm63xx/bcm63xx_dev_spi.h     |   10 +----
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h  |   40 +-------------------
 3 files changed, 10 insertions(+), 64 deletions(-)

diff --git a/arch/mips/bcm63xx/dev-spi.c b/arch/mips/bcm63xx/dev-spi.c
index f1c9c3e..2a43825 100644
--- a/arch/mips/bcm63xx/dev-spi.c
+++ b/arch/mips/bcm63xx/dev-spi.c
@@ -22,10 +22,6 @@
 /*
  * register offsets
  */
-static const unsigned long bcm6338_regs_spi[] = {
-	__GEN_SPI_REGS_TABLE(6338)
-};
-
 static const unsigned long bcm6348_regs_spi[] = {
 	__GEN_SPI_REGS_TABLE(6348)
 };
@@ -34,23 +30,15 @@ static const unsigned long bcm6358_regs_spi[] = {
 	__GEN_SPI_REGS_TABLE(6358)
 };
 
-static const unsigned long bcm6368_regs_spi[] = {
-	__GEN_SPI_REGS_TABLE(6368)
-};
-
 const unsigned long *bcm63xx_regs_spi;
 EXPORT_SYMBOL(bcm63xx_regs_spi);
 
 static __init void bcm63xx_spi_regs_init(void)
 {
-	if (BCMCPU_IS_6338())
-		bcm63xx_regs_spi = bcm6338_regs_spi;
-	if (BCMCPU_IS_6348())
+	if (BCMCPU_IS_6338() || BCMCPU_IS_6348())
 		bcm63xx_regs_spi = bcm6348_regs_spi;
-	if (BCMCPU_IS_6358())
+	if (BCMCPU_IS_6358() || BCMCPU_IS_6368())
 		bcm63xx_regs_spi = bcm6358_regs_spi;
-	if (BCMCPU_IS_6368())
-		bcm63xx_regs_spi = bcm6368_regs_spi;
 }
 #else
 static __init void bcm63xx_spi_regs_init(void) { }
@@ -104,10 +92,10 @@ int __init bcm63xx_spi_register(void)
 	spi_resources[1].start = bcm63xx_get_irq_number(IRQ_SPI);
 
 	if (BCMCPU_IS_6338() || BCMCPU_IS_6348()) {
-		spi_resources[0].end += BCM_6338_RSET_SPI_SIZE - 1;
-		spi_pdata.fifo_size = SPI_6338_MSG_DATA_SIZE;
-		spi_pdata.msg_type_shift = SPI_6338_MSG_TYPE_SHIFT;
-		spi_pdata.msg_ctl_width = SPI_6338_MSG_CTL_WIDTH;
+		spi_resources[0].end += BCM_6348_RSET_SPI_SIZE - 1;
+		spi_pdata.fifo_size = SPI_6348_MSG_DATA_SIZE;
+		spi_pdata.msg_type_shift = SPI_6348_MSG_TYPE_SHIFT;
+		spi_pdata.msg_ctl_width = SPI_6348_MSG_CTL_WIDTH;
 	}
 
 	if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) {
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
index c9bae13..cc15f7c 100644
--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
@@ -72,18 +72,12 @@ static inline unsigned long bcm63xx_spireg(enum bcm63xx_regs_spi reg)
 
 	return bcm63xx_regs_spi[reg];
 #else
-#ifdef CONFIG_BCM63XX_CPU_6338
-	__GEN_SPI_RSET(6338)
-#endif
-#ifdef CONFIG_BCM63XX_CPU_6348
+#if defined(CONFIG_BCM63XX_CPU_6338) || defined(CONFIG_BCM63XX_CPU_6348)
 	__GEN_SPI_RSET(6348)
 #endif
-#ifdef CONFIG_BCM63XX_CPU_6358
+#if defined(CONFIG_BCM63XX_CPU_6358) || defined(CONFIG_BCM63XX_CPU_6368)
 	__GEN_SPI_RSET(6358)
 #endif
-#ifdef CONFIG_BCM63XX_CPU_6368
-	__GEN_SPI_RSET(6368)
-#endif
 #endif
 	return 0;
 }
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
index 81b4702..acd1f93 100644
--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
@@ -1223,24 +1223,7 @@
  * _REG relative to RSET_SPI
  *************************************************************************/
 
-/* BCM 6338 SPI core */
-#define SPI_6338_CMD			0x00	/* 16-bits register */
-#define SPI_6338_INT_STATUS		0x02
-#define SPI_6338_INT_MASK_ST		0x03
-#define SPI_6338_INT_MASK		0x04
-#define SPI_6338_ST			0x05
-#define SPI_6338_CLK_CFG		0x06
-#define SPI_6338_FILL_BYTE		0x07
-#define SPI_6338_MSG_TAIL		0x09
-#define SPI_6338_RX_TAIL		0x0b
-#define SPI_6338_MSG_CTL		0x40	/* 8-bits register */
-#define SPI_6338_MSG_CTL_WIDTH		8
-#define SPI_6338_MSG_DATA		0x41
-#define SPI_6338_MSG_DATA_SIZE		0x3f
-#define SPI_6338_RX_DATA		0x80
-#define SPI_6338_RX_DATA_SIZE		0x3f
-
-/* BCM 6348 SPI core */
+/* BCM 6338/6348 SPI core */
 #define SPI_6348_CMD			0x00	/* 16-bits register */
 #define SPI_6348_INT_STATUS		0x02
 #define SPI_6348_INT_MASK_ST		0x03
@@ -1257,7 +1240,7 @@
 #define SPI_6348_RX_DATA		0x80
 #define SPI_6348_RX_DATA_SIZE		0x3f
 
-/* BCM 6358 SPI core */
+/* BCM 6358/6368 SPI core */
 #define SPI_6358_MSG_CTL		0x00	/* 16-bits register */
 #define SPI_6358_MSG_CTL_WIDTH		16
 #define SPI_6358_MSG_DATA		0x02
@@ -1274,23 +1257,6 @@
 #define SPI_6358_MSG_TAIL		0x709
 #define SPI_6358_RX_TAIL		0x70B
 
-/* BCM 6358 SPI core */
-#define SPI_6368_MSG_CTL		0x00	/* 16-bits register */
-#define SPI_6368_MSG_CTL_WIDTH		16
-#define SPI_6368_MSG_DATA		0x02
-#define SPI_6368_MSG_DATA_SIZE		0x21e
-#define SPI_6368_RX_DATA		0x400
-#define SPI_6368_RX_DATA_SIZE		0x220
-#define SPI_6368_CMD			0x700	/* 16-bits register */
-#define SPI_6368_INT_STATUS		0x702
-#define SPI_6368_INT_MASK_ST		0x703
-#define SPI_6368_INT_MASK		0x704
-#define SPI_6368_ST			0x705
-#define SPI_6368_CLK_CFG		0x706
-#define SPI_6368_FILL_BYTE		0x707
-#define SPI_6368_MSG_TAIL		0x709
-#define SPI_6368_RX_TAIL		0x70B
-
 /* Shared SPI definitions */
 
 /* Message configuration */
@@ -1298,10 +1264,8 @@
 #define SPI_HD_W			0x01
 #define SPI_HD_R			0x02
 #define SPI_BYTE_CNT_SHIFT		0
-#define SPI_6338_MSG_TYPE_SHIFT		6
 #define SPI_6348_MSG_TYPE_SHIFT		6
 #define SPI_6358_MSG_TYPE_SHIFT		14
-#define SPI_6368_MSG_TYPE_SHIFT		14
 
 /* Command */
 #define SPI_CMD_NOOP			0x00
-- 
1.7.10.4

[PATCH 2/7] MIPS: BCM63XX: fix revision ID width

[Jonas Gorski]

The REVID is only 8 bit wide.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
---
 arch/mips/bcm63xx/cpu.c                           |    4 ++--
 arch/mips/bcm63xx/setup.c                         |    2 +-
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h  |    2 +-
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h |    2 +-
 4 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/mips/bcm63xx/cpu.c b/arch/mips/bcm63xx/cpu.c
index a7afb28..ae16626 100644
--- a/arch/mips/bcm63xx/cpu.c
+++ b/arch/mips/bcm63xx/cpu.c
@@ -25,7 +25,7 @@ const int *bcm63xx_irqs;
 EXPORT_SYMBOL(bcm63xx_irqs);
 
 static u16 bcm63xx_cpu_id;
-static u16 bcm63xx_cpu_rev;
+static u8 bcm63xx_cpu_rev;
 static unsigned int bcm63xx_cpu_freq;
 static unsigned int bcm63xx_memory_size;
 
@@ -87,7 +87,7 @@ u16 __bcm63xx_get_cpu_id(void)
 
 EXPORT_SYMBOL(__bcm63xx_get_cpu_id);
 
-u16 bcm63xx_get_cpu_rev(void)
+u8 bcm63xx_get_cpu_rev(void)
 {
 	return bcm63xx_cpu_rev;
 }
diff --git a/arch/mips/bcm63xx/setup.c b/arch/mips/bcm63xx/setup.c
index 35e18e9..911fd7d 100644
--- a/arch/mips/bcm63xx/setup.c
+++ b/arch/mips/bcm63xx/setup.c
@@ -126,7 +126,7 @@ static void __bcm63xx_machine_reboot(char *p)
 const char *get_system_type(void)
 {
 	static char buf[128];
-	snprintf(buf, sizeof(buf), "bcm63xx/%s (0x%04x/0x%04X)",
+	snprintf(buf, sizeof(buf), "bcm63xx/%s (0x%04x/0x%02X)",
 		 board_get_name(),
 		 bcm63xx_get_cpu_id(), bcm63xx_get_cpu_rev());
 	return buf;
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
index cb922b9..19a80ea 100644
--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
@@ -18,7 +18,7 @@
 
 void __init bcm63xx_cpu_init(void);
 u16 __bcm63xx_get_cpu_id(void);
-u16 bcm63xx_get_cpu_rev(void);
+u8 bcm63xx_get_cpu_rev(void);
 unsigned int bcm63xx_get_cpu_freq(void);
 
 #ifdef CONFIG_BCM63XX_CPU_6328
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
index acd1f93..fe3601a 100644
--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
@@ -10,7 +10,7 @@
 #define REV_CHIPID_SHIFT		16
 #define REV_CHIPID_MASK			(0xffff << REV_CHIPID_SHIFT)
 #define REV_REVID_SHIFT			0
-#define REV_REVID_MASK			(0xffff << REV_REVID_SHIFT)
+#define REV_REVID_MASK			(0xff << REV_REVID_SHIFT)
 
 /* Clock Control register */
 #define PERF_CKCTL_REG			0x4
-- 
1.7.10.4

[PATCH 3/7] MIPS: BCM63XX: rework chip detection

[Jonas Gorski]

Instead of trying to use a correlation of cpu prid and chip id and
hoping they will always be unique, use the cpu prid to determine the
chip id register location and just read out the chip id.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
---
 arch/mips/bcm63xx/cpu.c |   87 +++++++++++++++++++++++------------------------
 1 file changed, 42 insertions(+), 45 deletions(-)

diff --git a/arch/mips/bcm63xx/cpu.c b/arch/mips/bcm63xx/cpu.c
index ae16626..fef168d 100644
--- a/arch/mips/bcm63xx/cpu.c
+++ b/arch/mips/bcm63xx/cpu.c
@@ -240,53 +240,27 @@ static unsigned int detect_memory_size(void)
 
 void __init bcm63xx_cpu_init(void)
 {
-	unsigned int tmp, expected_cpu_id;
+	unsigned int tmp;
 	struct cpuinfo_mips *c = &current_cpu_data;
 	unsigned int cpu = smp_processor_id();
+	u32 chipid_reg;
 
 	/* soc registers location depends on cpu type */
-	expected_cpu_id = 0;
+	chipid_reg = 0;
 
 	switch (c->cputype) {
 	case CPU_BMIPS3300:
-		if ((read_c0_prid() & 0xff00) == PRID_IMP_BMIPS3300_ALT) {
-			expected_cpu_id = BCM6348_CPU_ID;
-			bcm63xx_regs_base = bcm6348_regs_base;
-			bcm63xx_irqs = bcm6348_irqs;
-		} else {
+		if ((read_c0_prid() & 0xff00) != PRID_IMP_BMIPS3300_ALT)
 			__cpu_name[cpu] = "Broadcom BCM6338";
-			expected_cpu_id = BCM6338_CPU_ID;
-			bcm63xx_regs_base = bcm6338_regs_base;
-			bcm63xx_irqs = bcm6338_irqs;
-		}
-		break;
+		/* fall-through */
 	case CPU_BMIPS32:
-		expected_cpu_id = BCM6345_CPU_ID;
-		bcm63xx_regs_base = bcm6345_regs_base;
-		bcm63xx_irqs = bcm6345_irqs;
+		chipid_reg = BCM_6345_PERF_BASE;
 		break;
 	case CPU_BMIPS4350:
-		if ((read_c0_prid() & 0xf0) == 0x10) {
-			expected_cpu_id = BCM6358_CPU_ID;
-			bcm63xx_regs_base = bcm6358_regs_base;
-			bcm63xx_irqs = bcm6358_irqs;
-		} else {
-			/* all newer chips have the same chip id location */
-			u16 chip_id = bcm_readw(BCM_6368_PERF_BASE);
-
-			switch (chip_id) {
-			case BCM6328_CPU_ID:
-				expected_cpu_id = BCM6328_CPU_ID;
-				bcm63xx_regs_base = bcm6328_regs_base;
-				bcm63xx_irqs = bcm6328_irqs;
-				break;
-			case BCM6368_CPU_ID:
-				expected_cpu_id = BCM6368_CPU_ID;
-				bcm63xx_regs_base = bcm6368_regs_base;
-				bcm63xx_irqs = bcm6368_irqs;
-				break;
-			}
-		}
+		if ((read_c0_prid() & 0xf0) == 0x10)
+			chipid_reg = BCM_6345_PERF_BASE;
+		else
+			chipid_reg = BCM_6368_PERF_BASE;
 		break;
 	}
 
@@ -294,20 +268,43 @@ void __init bcm63xx_cpu_init(void)
 	 * really early to panic, but delaying panic would not help since we
 	 * will never get any working console
 	 */
-	if (!expected_cpu_id)
+	if (!chipid_reg)
 		panic("unsupported Broadcom CPU");
 
-	/*
-	 * bcm63xx_regs_base is set, we can access soc registers
-	 */
-
-	/* double check CPU type */
-	tmp = bcm_perf_readl(PERF_REV_REG);
+	/* read out CPU type */
+	tmp = bcm_readl(chipid_reg);
 	bcm63xx_cpu_id = (tmp & REV_CHIPID_MASK) >> REV_CHIPID_SHIFT;
 	bcm63xx_cpu_rev = (tmp & REV_REVID_MASK) >> REV_REVID_SHIFT;
 
-	if (bcm63xx_cpu_id != expected_cpu_id)
-		panic("bcm63xx CPU id mismatch");
+	switch (bcm63xx_cpu_id) {
+	case BCM6328_CPU_ID:
+		bcm63xx_regs_base = bcm6328_regs_base;
+		bcm63xx_irqs = bcm6328_irqs;
+		break;
+	case BCM6338_CPU_ID:
+		bcm63xx_regs_base = bcm6338_regs_base;
+		bcm63xx_irqs = bcm6338_irqs;
+		break;
+	case BCM6345_CPU_ID:
+		bcm63xx_regs_base = bcm6345_regs_base;
+		bcm63xx_irqs = bcm6345_irqs;
+		break;
+	case BCM6348_CPU_ID:
+		bcm63xx_regs_base = bcm6348_regs_base;
+		bcm63xx_irqs = bcm6348_irqs;
+		break;
+	case BCM6358_CPU_ID:
+		bcm63xx_regs_base = bcm6358_regs_base;
+		bcm63xx_irqs = bcm6358_irqs;
+		break;
+	case BCM6368_CPU_ID:
+		bcm63xx_regs_base = bcm6368_regs_base;
+		bcm63xx_irqs = bcm6368_irqs;
+		break;
+	default:
+		panic("unsupported broadcom CPU %x", bcm63xx_cpu_id);
+		break;
+	}
 
 	bcm63xx_cpu_freq = detect_cpu_clock();
 	bcm63xx_memory_size = detect_memory_size();
-- 
1.7.10.4

[PATCH 4/7] MIPS: BCM63XX: add basic BCM6362 support

[Jonas Gorski]

Add basic support for detecting and booting the BCM6362.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
---
 arch/mips/bcm63xx/Kconfig                         |    4 +
 arch/mips/bcm63xx/boards/board_bcm963xx.c         |    6 +-
 arch/mips/bcm63xx/cpu.c                           |   51 +++++++-
 arch/mips/bcm63xx/irq.c                           |   22 ++++
 arch/mips/bcm63xx/prom.c                          |    2 +
 arch/mips/bcm63xx/reset.c                         |   28 +++++
 arch/mips/bcm63xx/setup.c                         |    3 +
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h  |  139 +++++++++++++++++++++
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h |    2 +
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h |   61 ++++++++-
 arch/mips/include/asm/mach-bcm63xx/ioremap.h      |    1 +
 11 files changed, 314 insertions(+), 5 deletions(-)

diff --git a/arch/mips/bcm63xx/Kconfig b/arch/mips/bcm63xx/Kconfig
index d03e879..5639662 100644
--- a/arch/mips/bcm63xx/Kconfig
+++ b/arch/mips/bcm63xx/Kconfig
@@ -25,6 +25,10 @@ config BCM63XX_CPU_6358
 	bool "support 6358 CPU"
 	select HW_HAS_PCI
 
+config BCM63XX_CPU_6362
+	bool "support 6362 CPU"
+	select HW_HAS_PCI
+
 config BCM63XX_CPU_6368
 	bool "support 6368 CPU"
 	select HW_HAS_PCI
diff --git a/arch/mips/bcm63xx/boards/board_bcm963xx.c b/arch/mips/bcm63xx/boards/board_bcm963xx.c
index 9aa7d44..a9505c4 100644
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
@@ -726,11 +726,11 @@ void __init board_prom_init(void)
 	u32 val;
 
 	/* read base address of boot chip select (0)
-	 * 6328 does not have MPI but boots from a fixed address
+	 * 6328/6362 do not have MPI but boot from a fixed address
 	 */
-	if (BCMCPU_IS_6328())
+	if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) {
 		val = 0x18000000;
-	else {
+	} else {
 		val = bcm_mpi_readl(MPI_CSBASE_REG(0));
 		val &= MPI_CSBASE_BASE_MASK;
 	}
diff --git a/arch/mips/bcm63xx/cpu.c b/arch/mips/bcm63xx/cpu.c
index fef168d..79fe32d 100644
--- a/arch/mips/bcm63xx/cpu.c
+++ b/arch/mips/bcm63xx/cpu.c
@@ -71,6 +71,15 @@ static const int bcm6358_irqs[] = {
 
 };
 
+static const unsigned long bcm6362_regs_base[] = {
+	__GEN_CPU_REGS_TABLE(6362)
+};
+
+static const int bcm6362_irqs[] = {
+	__GEN_CPU_IRQ_TABLE(6362)
+
+};
+
 static const unsigned long bcm6368_regs_base[] = {
 	__GEN_CPU_REGS_TABLE(6368)
 };
@@ -169,6 +178,42 @@ static unsigned int detect_cpu_clock(void)
 		return (16 * 1000000 * n1 * n2) / m1;
 	}
 
+	case BCM6362_CPU_ID:
+	{
+		unsigned int tmp, mips_pll_fcvo;
+
+		tmp = bcm_misc_readl(MISC_STRAPBUS_6362_REG);
+		mips_pll_fcvo = (tmp & STRAPBUS_6362_FCVO_MASK)
+				>> STRAPBUS_6362_FCVO_SHIFT;
+		switch (mips_pll_fcvo) {
+		case 0x03:
+		case 0x0b:
+		case 0x13:
+		case 0x1b:
+			return 240000000;
+		case 0x04:
+		case 0x0c:
+		case 0x14:
+		case 0x1c:
+			return 160000000;
+		case 0x05:
+		case 0x0e:
+		case 0x16:
+		case 0x1e:
+		case 0x1f:
+			return 400000000;
+		case 0x06:
+			return 440000000;
+		case 0x07:
+		case 0x17:
+			return 384000000;
+		case 0x15:
+		case 0x1d:
+			return 200000000;
+		default:
+			return 320000000;
+		}
+	}
 	case BCM6368_CPU_ID:
 	{
 		unsigned int tmp, p1, p2, ndiv, m1;
@@ -205,7 +250,7 @@ static unsigned int detect_memory_size(void)
 	unsigned int cols = 0, rows = 0, is_32bits = 0, banks = 0;
 	u32 val;
 
-	if (BCMCPU_IS_6328())
+	if (BCMCPU_IS_6328() || BCMCPU_IS_6362())
 		return bcm_ddr_readl(DDR_CSEND_REG) << 24;
 
 	if (BCMCPU_IS_6345()) {
@@ -297,6 +342,10 @@ void __init bcm63xx_cpu_init(void)
 		bcm63xx_regs_base = bcm6358_regs_base;
 		bcm63xx_irqs = bcm6358_irqs;
 		break;
+	case BCM6362_CPU_ID:
+		bcm63xx_regs_base = bcm6362_regs_base;
+		bcm63xx_irqs = bcm6362_irqs;
+		break;
 	case BCM6368_CPU_ID:
 		bcm63xx_regs_base = bcm6368_regs_base;
 		bcm63xx_irqs = bcm6368_irqs;
diff --git a/arch/mips/bcm63xx/irq.c b/arch/mips/bcm63xx/irq.c
index da24c2b..c0ab388 100644
--- a/arch/mips/bcm63xx/irq.c
+++ b/arch/mips/bcm63xx/irq.c
@@ -82,6 +82,17 @@ static void __internal_irq_unmask_64(unsigned int irq) __maybe_unused;
 #define ext_irq_cfg_reg1	PERF_EXTIRQ_CFG_REG_6358
 #define ext_irq_cfg_reg2	0
 #endif
+#ifdef CONFIG_BCM63XX_CPU_6362
+#define irq_stat_reg		PERF_IRQSTAT_6362_REG
+#define irq_mask_reg		PERF_IRQMASK_6362_REG
+#define irq_bits		64
+#define is_ext_irq_cascaded	1
+#define ext_irq_start		(BCM_6362_EXT_IRQ0 - IRQ_INTERNAL_BASE)
+#define ext_irq_end		(BCM_6362_EXT_IRQ3 - IRQ_INTERNAL_BASE)
+#define ext_irq_count		4
+#define ext_irq_cfg_reg1	PERF_EXTIRQ_CFG_REG_6362
+#define ext_irq_cfg_reg2	0
+#endif
 #ifdef CONFIG_BCM63XX_CPU_6368
 #define irq_stat_reg		PERF_IRQSTAT_6368_REG
 #define irq_mask_reg		PERF_IRQMASK_6368_REG
@@ -170,6 +181,16 @@ static void bcm63xx_init_irq(void)
 		ext_irq_end = BCM_6358_EXT_IRQ3 - IRQ_INTERNAL_BASE;
 		ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6358;
 		break;
+	case BCM6362_CPU_ID:
+		irq_stat_addr += PERF_IRQSTAT_6362_REG;
+		irq_mask_addr += PERF_IRQMASK_6362_REG;
+		irq_bits = 64;
+		ext_irq_count = 4;
+		is_ext_irq_cascaded = 1;
+		ext_irq_start = BCM_6362_EXT_IRQ0 - IRQ_INTERNAL_BASE;
+		ext_irq_end = BCM_6362_EXT_IRQ3 - IRQ_INTERNAL_BASE;
+		ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6362;
+		break;
 	case BCM6368_CPU_ID:
 		irq_stat_addr += PERF_IRQSTAT_6368_REG;
 		irq_mask_addr += PERF_IRQMASK_6368_REG;
@@ -458,6 +479,7 @@ static int bcm63xx_external_irq_set_type(struct irq_data *d,
 	case BCM6338_CPU_ID:
 	case BCM6345_CPU_ID:
 	case BCM6358_CPU_ID:
+	case BCM6362_CPU_ID:
 	case BCM6368_CPU_ID:
 		if (levelsense)
 			reg |= EXTIRQ_CFG_LEVELSENSE(irq);
diff --git a/arch/mips/bcm63xx/prom.c b/arch/mips/bcm63xx/prom.c
index 10eaff4..fd69808 100644
--- a/arch/mips/bcm63xx/prom.c
+++ b/arch/mips/bcm63xx/prom.c
@@ -36,6 +36,8 @@ void __init prom_init(void)
 		mask = CKCTL_6348_ALL_SAFE_EN;
 	else if (BCMCPU_IS_6358())
 		mask = CKCTL_6358_ALL_SAFE_EN;
+	else if (BCMCPU_IS_6362())
+		mask = CKCTL_6362_ALL_SAFE_EN;
 	else if (BCMCPU_IS_6368())
 		mask = CKCTL_6368_ALL_SAFE_EN;
 	else
diff --git a/arch/mips/bcm63xx/reset.c b/arch/mips/bcm63xx/reset.c
index 68a31bb..317931c 100644
--- a/arch/mips/bcm63xx/reset.c
+++ b/arch/mips/bcm63xx/reset.c
@@ -85,6 +85,20 @@
 #define BCM6358_RESET_PCIE	0
 #define BCM6358_RESET_PCIE_EXT	0
 
+#define BCM6362_RESET_SPI	SOFTRESET_6362_SPI_MASK
+#define BCM6362_RESET_ENET	0
+#define BCM6362_RESET_USBH	SOFTRESET_6362_USBH_MASK
+#define BCM6362_RESET_USBD	SOFTRESET_6362_USBS_MASK
+#define BCM6362_RESET_DSL	0
+#define BCM6362_RESET_SAR	SOFTRESET_6362_SAR_MASK
+#define BCM6362_RESET_EPHY	SOFTRESET_6362_EPHY_MASK
+#define BCM6362_RESET_ENETSW	SOFTRESET_6362_ENETSW_MASK
+#define BCM6362_RESET_PCM	SOFTRESET_6362_PCM_MASK
+#define BCM6362_RESET_MPI	0
+#define BCM6362_RESET_PCIE      (SOFTRESET_6362_PCIE_MASK | \
+				 SOFTRESET_6362_PCIE_CORE_MASK)
+#define BCM6362_RESET_PCIE_EXT	SOFTRESET_6362_PCIE_EXT_MASK
+
 #define BCM6368_RESET_SPI	SOFTRESET_6368_SPI_MASK
 #define BCM6368_RESET_ENET	0
 #define BCM6368_RESET_USBH	SOFTRESET_6368_USBH_MASK
@@ -119,6 +133,10 @@ static const u32 bcm6358_reset_bits[] = {
 	__GEN_RESET_BITS_TABLE(6358)
 };
 
+static const u32 bcm6362_reset_bits[] = {
+	__GEN_RESET_BITS_TABLE(6362)
+};
+
 static const u32 bcm6368_reset_bits[] = {
 	__GEN_RESET_BITS_TABLE(6368)
 };
@@ -140,6 +158,9 @@ static int __init bcm63xx_reset_bits_init(void)
 	} else if (BCMCPU_IS_6358()) {
 		reset_reg = PERF_SOFTRESET_6358_REG;
 		bcm63xx_reset_bits = bcm6358_reset_bits;
+	} else if (BCMCPU_IS_6362()) {
+		reset_reg = PERF_SOFTRESET_6362_REG;
+		bcm63xx_reset_bits = bcm6362_reset_bits;
 	} else if (BCMCPU_IS_6368()) {
 		reset_reg = PERF_SOFTRESET_6368_REG;
 		bcm63xx_reset_bits = bcm6368_reset_bits;
@@ -182,6 +203,13 @@ static const u32 bcm63xx_reset_bits[] = {
 #define reset_reg PERF_SOFTRESET_6358_REG
 #endif
 
+#ifdef CONFIG_BCM63XX_CPU_6362
+static const u32 bcm63xx_reset_bits[] = {
+	__GEN_RESET_BITS_TABLE(6362)
+};
+#define reset_reg PERF_SOFTRESET_6362_REG
+#endif
+
 #ifdef CONFIG_BCM63XX_CPU_6368
 static const u32 bcm63xx_reset_bits[] = {
 	__GEN_RESET_BITS_TABLE(6368)
diff --git a/arch/mips/bcm63xx/setup.c b/arch/mips/bcm63xx/setup.c
index 911fd7d..24a2444 100644
--- a/arch/mips/bcm63xx/setup.c
+++ b/arch/mips/bcm63xx/setup.c
@@ -83,6 +83,9 @@ void bcm63xx_machine_reboot(void)
 	case BCM6358_CPU_ID:
 		perf_regs[0] = PERF_EXTIRQ_CFG_REG_6358;
 		break;
+	case BCM6362_CPU_ID:
+		perf_regs[0] = PERF_EXTIRQ_CFG_REG_6362;
+		break;
 	}
 
 	for (i = 0; i < 2; i++) {
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
index 19a80ea..3362289 100644
--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
@@ -14,6 +14,7 @@
 #define BCM6345_CPU_ID		0x6345
 #define BCM6348_CPU_ID		0x6348
 #define BCM6358_CPU_ID		0x6358
+#define BCM6362_CPU_ID		0x6362
 #define BCM6368_CPU_ID		0x6368
 
 void __init bcm63xx_cpu_init(void);
@@ -86,6 +87,20 @@ unsigned int bcm63xx_get_cpu_freq(void);
 # define BCMCPU_IS_6358()	(0)
 #endif
 
+#ifdef CONFIG_BCM63XX_CPU_6362
+# ifdef bcm63xx_get_cpu_id
+#  undef bcm63xx_get_cpu_id
+#  define bcm63xx_get_cpu_id()	__bcm63xx_get_cpu_id()
+#  define BCMCPU_RUNTIME_DETECT
+# else
+#  define bcm63xx_get_cpu_id()	BCM6362_CPU_ID
+# endif
+# define BCMCPU_IS_6362()	(bcm63xx_get_cpu_id() == BCM6362_CPU_ID)
+#else
+# define BCMCPU_IS_6362()	(0)
+#endif
+
+
 #ifdef CONFIG_BCM63XX_CPU_6368
 # ifdef bcm63xx_get_cpu_id
 #  undef bcm63xx_get_cpu_id
@@ -406,6 +421,62 @@ enum bcm63xx_regs_set {
 
 
 /*
+ * 6362 register sets base address
+ */
+#define BCM_6362_DSL_LMEM_BASE		(0xdeadbeef)
+#define BCM_6362_PERF_BASE		(0xb0000000)
+#define BCM_6362_TIMER_BASE		(0xb0000040)
+#define BCM_6362_WDT_BASE		(0xb000005c)
+#define BCM_6362_UART0_BASE             (0xb0000100)
+#define BCM_6362_UART1_BASE		(0xb0000120)
+#define BCM_6362_GPIO_BASE		(0xb0000080)
+#define BCM_6362_SPI_BASE		(0xb0000800)
+#define BCM_6362_HSSPI_BASE		(0xb0001000)
+#define BCM_6362_UDC0_BASE		(0xdeadbeef)
+#define BCM_6362_USBDMA_BASE		(0xb000c000)
+#define BCM_6362_OHCI0_BASE		(0xb0002600)
+#define BCM_6362_OHCI_PRIV_BASE		(0xdeadbeef)
+#define BCM_6362_USBH_PRIV_BASE		(0xb0002700)
+#define BCM_6362_USBD_BASE		(0xb0002400)
+#define BCM_6362_MPI_BASE		(0xdeadbeef)
+#define BCM_6362_PCMCIA_BASE		(0xdeadbeef)
+#define BCM_6362_PCIE_BASE		(0xb0e40000)
+#define BCM_6362_SDRAM_REGS_BASE	(0xdeadbeef)
+#define BCM_6362_DSL_BASE		(0xdeadbeef)
+#define BCM_6362_UBUS_BASE		(0xdeadbeef)
+#define BCM_6362_ENET0_BASE		(0xdeadbeef)
+#define BCM_6362_ENET1_BASE		(0xdeadbeef)
+#define BCM_6362_ENETDMA_BASE		(0xb000d800)
+#define BCM_6362_ENETDMAC_BASE		(0xb000da00)
+#define BCM_6362_ENETDMAS_BASE		(0xb000dc00)
+#define BCM_6362_ENETSW_BASE		(0xb0e00000)
+#define BCM_6362_EHCI0_BASE		(0xb0002500)
+#define BCM_6362_SDRAM_BASE		(0xdeadbeef)
+#define BCM_6362_MEMC_BASE		(0xdeadbeef)
+#define BCM_6362_DDR_BASE		(0xb0003000)
+#define BCM_6362_M2M_BASE		(0xdeadbeef)
+#define BCM_6362_ATM_BASE		(0xdeadbeef)
+#define BCM_6362_XTM_BASE		(0xb0007800)
+#define BCM_6362_XTMDMA_BASE		(0xb000b800)
+#define BCM_6362_XTMDMAC_BASE		(0xdeadbeef)
+#define BCM_6362_XTMDMAS_BASE		(0xdeadbeef)
+#define BCM_6362_PCM_BASE		(0xb000a800)
+#define BCM_6362_PCMDMA_BASE		(0xdeadbeef)
+#define BCM_6362_PCMDMAC_BASE		(0xdeadbeef)
+#define BCM_6362_PCMDMAS_BASE		(0xdeadbeef)
+#define BCM_6362_RNG_BASE		(0xdeadbeef)
+#define BCM_6362_MISC_BASE		(0xb0001800)
+
+#define BCM_6362_NAND_REG_BASE		(0xb0000200)
+#define BCM_6362_NAND_CACHE_BASE	(0xb0000600)
+#define BCM_6362_LED_BASE		(0xb0001900)
+#define BCM_6362_IPSEC_BASE		(0xb0002800)
+#define BCM_6362_IPSEC_DMA_BASE		(0xb000d000)
+#define BCM_6362_WLAN_CHIPCOMMON_BASE	(0xb0004000)
+#define BCM_6362_WLAN_D11_BASE		(0xb0005000)
+#define BCM_6362_WLAN_SHIM_BASE		(0xb0007000)
+
+/*
  * 6368 register sets base address
  */
 #define BCM_6368_DSL_LMEM_BASE		(0xdeadbeef)
@@ -564,6 +635,9 @@ static inline unsigned long bcm63xx_regset_address(enum bcm63xx_regs_set set)
 #ifdef CONFIG_BCM63XX_CPU_6358
 	__GEN_RSET(6358)
 #endif
+#ifdef CONFIG_BCM63XX_CPU_6362
+	__GEN_RSET(6362)
+#endif
 #ifdef CONFIG_BCM63XX_CPU_6368
 	__GEN_RSET(6368)
 #endif
@@ -820,6 +894,71 @@ enum bcm63xx_irq {
 #define BCM_6358_EXT_IRQ3		(IRQ_INTERNAL_BASE + 28)
 
 /*
+ * 6362 irqs
+ */
+#define BCM_6362_HIGH_IRQ_BASE		(IRQ_INTERNAL_BASE + 32)
+
+#define BCM_6362_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
+#define BCM_6362_SPI_IRQ		(IRQ_INTERNAL_BASE + 2)
+#define BCM_6362_UART0_IRQ		(IRQ_INTERNAL_BASE + 3)
+#define BCM_6362_UART1_IRQ		(IRQ_INTERNAL_BASE + 4)
+#define BCM_6362_DSL_IRQ		(IRQ_INTERNAL_BASE + 28)
+#define BCM_6362_UDC0_IRQ		0
+#define BCM_6362_ENET0_IRQ		0
+#define BCM_6362_ENET1_IRQ		0
+#define BCM_6362_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 14)
+#define BCM_6362_HSSPI_IRQ		(IRQ_INTERNAL_BASE + 5)
+#define BCM_6362_OHCI0_IRQ		(IRQ_INTERNAL_BASE + 9)
+#define BCM_6362_EHCI0_IRQ		(IRQ_INTERNAL_BASE + 10)
+#define BCM_6362_USBD_IRQ		(IRQ_INTERNAL_BASE + 11)
+#define BCM_6362_USBD_RXDMA0_IRQ	(IRQ_INTERNAL_BASE + 20)
+#define BCM_6362_USBD_TXDMA0_IRQ	(IRQ_INTERNAL_BASE + 21)
+#define BCM_6362_USBD_RXDMA1_IRQ	(IRQ_INTERNAL_BASE + 22)
+#define BCM_6362_USBD_TXDMA1_IRQ	(IRQ_INTERNAL_BASE + 23)
+#define BCM_6362_USBD_RXDMA2_IRQ	(IRQ_INTERNAL_BASE + 24)
+#define BCM_6362_USBD_TXDMA2_IRQ	(IRQ_INTERNAL_BASE + 25)
+#define BCM_6362_PCMCIA_IRQ		0
+#define BCM_6362_ENET0_RXDMA_IRQ	0
+#define BCM_6362_ENET0_TXDMA_IRQ	0
+#define BCM_6362_ENET1_RXDMA_IRQ	0
+#define BCM_6362_ENET1_TXDMA_IRQ	0
+#define BCM_6362_PCI_IRQ		(IRQ_INTERNAL_BASE + 30)
+#define BCM_6362_ATM_IRQ		0
+#define BCM_6362_ENETSW_RXDMA0_IRQ	(BCM_6362_HIGH_IRQ_BASE + 0)
+#define BCM_6362_ENETSW_RXDMA1_IRQ	(BCM_6362_HIGH_IRQ_BASE + 1)
+#define BCM_6362_ENETSW_RXDMA2_IRQ	(BCM_6362_HIGH_IRQ_BASE + 2)
+#define BCM_6362_ENETSW_RXDMA3_IRQ	(BCM_6362_HIGH_IRQ_BASE + 3)
+#define BCM_6362_ENETSW_TXDMA0_IRQ	0
+#define BCM_6362_ENETSW_TXDMA1_IRQ	0
+#define BCM_6362_ENETSW_TXDMA2_IRQ	0
+#define BCM_6362_ENETSW_TXDMA3_IRQ	0
+#define BCM_6362_XTM_IRQ		0
+#define BCM_6362_XTM_DMA0_IRQ		(BCM_6362_HIGH_IRQ_BASE + 12)
+
+#define BCM_6362_RING_OSC_IRQ		(IRQ_INTERNAL_BASE + 1)
+#define BCM_6362_WLAN_GPIO_IRQ		(IRQ_INTERNAL_BASE + 6)
+#define BCM_6362_WLAN_IRQ		(IRQ_INTERNAL_BASE + 7)
+#define BCM_6362_IPSEC_IRQ		(IRQ_INTERNAL_BASE + 8)
+#define BCM_6362_NAND_IRQ		(IRQ_INTERNAL_BASE + 12)
+#define BCM_6362_PCM_IRQ		(IRQ_INTERNAL_BASE + 13)
+#define BCM_6362_DG_IRQ			(IRQ_INTERNAL_BASE + 15)
+#define BCM_6362_EPHY_ENERGY0_IRQ	(IRQ_INTERNAL_BASE + 16)
+#define BCM_6362_EPHY_ENERGY1_IRQ	(IRQ_INTERNAL_BASE + 17)
+#define BCM_6362_EPHY_ENERGY2_IRQ	(IRQ_INTERNAL_BASE + 18)
+#define BCM_6362_EPHY_ENERGY3_IRQ	(IRQ_INTERNAL_BASE + 19)
+#define BCM_6362_IPSEC_DMA0_IRQ		(IRQ_INTERNAL_BASE + 26)
+#define BCM_6362_IPSEC_DMA1_IRQ		(IRQ_INTERNAL_BASE + 27)
+#define BCM_6362_FAP0_IRQ		(IRQ_INTERNAL_BASE + 29)
+#define BCM_6362_PCM_DMA0_IRQ		(BCM_6362_HIGH_IRQ_BASE + 4)
+#define BCM_6362_PCM_DMA1_IRQ		(BCM_6362_HIGH_IRQ_BASE + 5)
+#define BCM_6362_DECT0_IRQ		(BCM_6362_HIGH_IRQ_BASE + 6)
+#define BCM_6362_DECT1_IRQ		(BCM_6362_HIGH_IRQ_BASE + 7)
+#define BCM_6362_EXT_IRQ0		(BCM_6362_HIGH_IRQ_BASE + 8)
+#define BCM_6362_EXT_IRQ1		(BCM_6362_HIGH_IRQ_BASE + 9)
+#define BCM_6362_EXT_IRQ2		(BCM_6362_HIGH_IRQ_BASE + 10)
+#define BCM_6362_EXT_IRQ3		(BCM_6362_HIGH_IRQ_BASE + 11)
+
+/*
  * 6368 irqs
  */
 #define BCM_6368_HIGH_IRQ_BASE		(IRQ_INTERNAL_BASE + 32)
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h
index 0a9891f..35baa1a 100644
--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h
@@ -17,6 +17,8 @@ static inline unsigned long bcm63xx_gpio_count(void)
 		return 8;
 	case BCM6345_CPU_ID:
 		return 16;
+	case BCM6362_CPU_ID:
+		return 48;
 	case BCM6368_CPU_ID:
 		return 38;
 	case BCM6348_CPU_ID:
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
index fe3601a..129b8a6 100644
--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
@@ -112,6 +112,39 @@
 					CKCTL_6358_USBSU_EN |		\
 					CKCTL_6358_EPHY_EN)
 
+#define CKCTL_6362_ADSL_QPROC_EN	(1 << 1)
+#define CKCTL_6362_ADSL_AFE_EN		(1 << 2)
+#define CKCTL_6362_ADSL_EN		(1 << 3)
+#define CKCTL_6362_MIPS_EN		(1 << 4)
+#define CKCTL_6362_WLAN_OCP_EN		(1 << 5)
+#define CKCTL_6362_SWPKT_USB_EN		(1 << 7)
+#define CKCTL_6362_SWPKT_SAR_EN		(1 << 8)
+#define CKCTL_6362_SAR_EN		(1 << 9)
+#define CKCTL_6362_ROBOSW_EN		(1 << 10)
+#define CKCTL_6362_PCM_EN		(1 << 11)
+#define CKCTL_6362_USBD_EN		(1 << 12)
+#define CKCTL_6362_USBH_EN		(1 << 13)
+#define CKCTL_6362_IPSEC_EN		(1 << 14)
+#define CKCTL_6362_SPI_EN		(1 << 15)
+#define CKCTL_6362_HSSPI_EN		(1 << 16)
+#define CKCTL_6362_PCIE_EN		(1 << 17)
+#define CKCTL_6362_FAP_EN		(1 << 18)
+#define CKCTL_6362_PHYMIPS_EN		(1 << 19)
+#define CKCTL_6362_NAND_EN		(1 << 20)
+
+#define CKCTL_6362_ALL_SAFE_EN		(CKCTL_6362_PHYMIPS_EN |	\
+					CKCTL_6362_ADSL_QPROC_EN |	\
+					CKCTL_6362_ADSL_AFE_EN |	\
+					CKCTL_6362_ADSL_EN |		\
+					CKCTL_6362_SAR_EN  |		\
+					CKCTL_6362_PCM_EN  |		\
+					CKCTL_6362_IPSEC_EN |		\
+					CKCTL_6362_USBD_EN |		\
+					CKCTL_6362_USBH_EN |		\
+					CKCTL_6362_ROBOSW_EN |		\
+					CKCTL_6362_PCIE_EN)
+
+
 #define CKCTL_6368_VDSL_QPROC_EN	(1 << 2)
 #define CKCTL_6368_VDSL_AFE_EN		(1 << 3)
 #define CKCTL_6368_VDSL_BONDING_EN	(1 << 4)
@@ -153,6 +186,7 @@
 #define PERF_IRQMASK_6345_REG		0xc
 #define PERF_IRQMASK_6348_REG		0xc
 #define PERF_IRQMASK_6358_REG		0xc
+#define PERF_IRQMASK_6362_REG		0x20
 #define PERF_IRQMASK_6368_REG		0x20
 
 /* Interrupt Status register */
@@ -161,6 +195,7 @@
 #define PERF_IRQSTAT_6345_REG		0x10
 #define PERF_IRQSTAT_6348_REG		0x10
 #define PERF_IRQSTAT_6358_REG		0x10
+#define PERF_IRQSTAT_6362_REG		0x28
 #define PERF_IRQSTAT_6368_REG		0x28
 
 /* External Interrupt Configuration register */
@@ -169,6 +204,7 @@
 #define PERF_EXTIRQ_CFG_REG_6345	0x14
 #define PERF_EXTIRQ_CFG_REG_6348	0x14
 #define PERF_EXTIRQ_CFG_REG_6358	0x14
+#define PERF_EXTIRQ_CFG_REG_6362	0x18
 #define PERF_EXTIRQ_CFG_REG_6368	0x18
 
 #define PERF_EXTIRQ_CFG_REG2_6368	0x1c
@@ -197,6 +233,7 @@
 #define PERF_SOFTRESET_REG		0x28
 #define PERF_SOFTRESET_6328_REG		0x10
 #define PERF_SOFTRESET_6358_REG		0x34
+#define PERF_SOFTRESET_6362_REG		0x10
 #define PERF_SOFTRESET_6368_REG		0x10
 
 #define SOFTRESET_6328_SPI_MASK		(1 << 0)
@@ -259,6 +296,22 @@
 #define SOFTRESET_6358_PCM_MASK		(1 << 13)
 #define SOFTRESET_6358_ADSL_MASK	(1 << 14)
 
+#define SOFTRESET_6362_SPI_MASK		(1 << 0)
+#define SOFTRESET_6362_IPSEC_MASK	(1 << 1)
+#define SOFTRESET_6362_EPHY_MASK	(1 << 2)
+#define SOFTRESET_6362_SAR_MASK		(1 << 3)
+#define SOFTRESET_6362_ENETSW_MASK	(1 << 4)
+#define SOFTRESET_6362_USBS_MASK	(1 << 5)
+#define SOFTRESET_6362_USBH_MASK	(1 << 6)
+#define SOFTRESET_6362_PCM_MASK		(1 << 7)
+#define SOFTRESET_6362_PCIE_CORE_MASK	(1 << 8)
+#define SOFTRESET_6362_PCIE_MASK	(1 << 9)
+#define SOFTRESET_6362_PCIE_EXT_MASK	(1 << 10)
+#define SOFTRESET_6362_WLAN_SHIM_MASK	(1 << 11)
+#define SOFTRESET_6362_DDR_PHY_MASK	(1 << 12)
+#define SOFTRESET_6362_FAP_MASK		(1 << 13)
+#define SOFTRESET_6362_WLAN_UBUS_MASK	(1 << 14)
+
 #define SOFTRESET_6368_SPI_MASK		(1 << 0)
 #define SOFTRESET_6368_MPI_MASK		(1 << 3)
 #define SOFTRESET_6368_EPHY_MASK	(1 << 6)
@@ -1240,7 +1293,7 @@
 #define SPI_6348_RX_DATA		0x80
 #define SPI_6348_RX_DATA_SIZE		0x3f
 
-/* BCM 6358/6368 SPI core */
+/* BCM 6358/6262/6368 SPI core */
 #define SPI_6358_MSG_CTL		0x00	/* 16-bits register */
 #define SPI_6358_MSG_CTL_WIDTH		16
 #define SPI_6358_MSG_DATA		0x02
@@ -1316,6 +1369,12 @@
 #define SERDES_PCIE_EN			(1 << 0)
 #define SERDES_PCIE_EXD_EN		(1 << 15)
 
+#define MISC_STRAPBUS_6362_REG		0x14
+#define STRAPBUS_6362_FCVO_SHIFT	1
+#define STRAPBUS_6362_FCVO_MASK		(0x1f << STRAPBUS_6362_FCVO_SHIFT)
+#define STRAPBUS_6362_BOOT_SEL_SERIAL	(1 << 15)
+#define STRAPBUS_6362_BOOT_SEL_NAND	(0 << 15)
+
 #define MISC_STRAPBUS_6328_REG		0x240
 #define STRAPBUS_6328_FCVO_SHIFT	7
 #define STRAPBUS_6328_FCVO_MASK		(0x1f << STRAPBUS_6328_FCVO_SHIFT)
diff --git a/arch/mips/include/asm/mach-bcm63xx/ioremap.h b/arch/mips/include/asm/mach-bcm63xx/ioremap.h
index 30931c4..94e3011 100644
--- a/arch/mips/include/asm/mach-bcm63xx/ioremap.h
+++ b/arch/mips/include/asm/mach-bcm63xx/ioremap.h
@@ -19,6 +19,7 @@ static inline int is_bcm63xx_internal_registers(phys_t offset)
 			return 1;
 		break;
 	case BCM6328_CPU_ID:
+	case BCM6362_CPU_ID:
 	case BCM6368_CPU_ID:
 		if (offset >= 0xb0000000 && offset < 0xb1000000)
 			return 1;
-- 
1.7.10.4

[PATCH 5/7] MIPS: BCM63XX: enable SPI controller for BCM6362

[Jonas Gorski]

The SPI controller shares the same register layout as the 6358 one.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
---
 arch/mips/bcm63xx/clk.c                              |    2 ++
 arch/mips/bcm63xx/dev-spi.c                          |    4 ++--
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h |    3 ++-
 3 files changed, 6 insertions(+), 3 deletions(-)

diff --git a/arch/mips/bcm63xx/clk.c b/arch/mips/bcm63xx/clk.c
index b9e948d..e357d55 100644
--- a/arch/mips/bcm63xx/clk.c
+++ b/arch/mips/bcm63xx/clk.c
@@ -196,6 +196,8 @@ static void spi_set(struct clk *clk, int enable)
 		mask = CKCTL_6348_SPI_EN;
 	else if (BCMCPU_IS_6358())
 		mask = CKCTL_6358_SPI_EN;
+	else if (BCMCPU_IS_6362())
+		mask = CKCTL_6362_SPI_EN;
 	else
 		/* BCMCPU_IS_6368 */
 		mask = CKCTL_6368_SPI_EN;
diff --git a/arch/mips/bcm63xx/dev-spi.c b/arch/mips/bcm63xx/dev-spi.c
index 2a43825..854e936 100644
--- a/arch/mips/bcm63xx/dev-spi.c
+++ b/arch/mips/bcm63xx/dev-spi.c
@@ -37,7 +37,7 @@ static __init void bcm63xx_spi_regs_init(void)
 {
 	if (BCMCPU_IS_6338() || BCMCPU_IS_6348())
 		bcm63xx_regs_spi = bcm6348_regs_spi;
-	if (BCMCPU_IS_6358() || BCMCPU_IS_6368())
+	if (BCMCPU_IS_6358() || BCMCPU_IS_6362() || BCMCPU_IS_6368())
 		bcm63xx_regs_spi = bcm6358_regs_spi;
 }
 #else
@@ -98,7 +98,7 @@ int __init bcm63xx_spi_register(void)
 		spi_pdata.msg_ctl_width = SPI_6348_MSG_CTL_WIDTH;
 	}
 
-	if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) {
+	if (BCMCPU_IS_6358() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) {
 		spi_resources[0].end += BCM_6358_RSET_SPI_SIZE - 1;
 		spi_pdata.fifo_size = SPI_6358_MSG_DATA_SIZE;
 		spi_pdata.msg_type_shift = SPI_6358_MSG_TYPE_SHIFT;
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
index cc15f7c..6515da9 100644
--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
@@ -75,7 +75,8 @@ static inline unsigned long bcm63xx_spireg(enum bcm63xx_regs_spi reg)
 #if defined(CONFIG_BCM63XX_CPU_6338) || defined(CONFIG_BCM63XX_CPU_6348)
 	__GEN_SPI_RSET(6348)
 #endif
-#if defined(CONFIG_BCM63XX_CPU_6358) || defined(CONFIG_BCM63XX_CPU_6368)
+#if defined(CONFIG_BCM63XX_CPU_6358) || defined(CONFIG_BCM63XX_CPU_6362) || \
+	defined(CONFIG_BCM63XX_CPU_6368)
 	__GEN_SPI_RSET(6358)
 #endif
 #endif
-- 
1.7.10.4

[PATCH 6/7] MIPS: BCM63XX: enable pcie for BCM6362

[Jonas Gorski]

The PCIe controller is almost the same as the BCM6328 one, with only
the SERDES register being at a different location.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
---
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h |    3 ++-
 arch/mips/pci/pci-bcm63xx.c                       |   11 +++++++++--
 2 files changed, 11 insertions(+), 3 deletions(-)

diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
index 129b8a6..243bab9 100644
--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
@@ -1365,7 +1365,8 @@
 /*************************************************************************
  * _REG relative to RSET_MISC
  *************************************************************************/
-#define MISC_SERDES_CTRL_REG		0x0
+#define MISC_SERDES_CTRL_6328_REG	0x0
+#define MISC_SERDES_CTRL_6362_REG	0x4
 #define SERDES_PCIE_EN			(1 << 0)
 #define SERDES_PCIE_EXD_EN		(1 << 15)
 
diff --git a/arch/mips/pci/pci-bcm63xx.c b/arch/mips/pci/pci-bcm63xx.c
index 88e781c..2eb9542 100644
--- a/arch/mips/pci/pci-bcm63xx.c
+++ b/arch/mips/pci/pci-bcm63xx.c
@@ -121,11 +121,17 @@ void __iomem *pci_iospace_start;
 static void __init bcm63xx_reset_pcie(void)
 {
 	u32 val;
+	u32 reg;
 
 	/* enable SERDES */
-	val = bcm_misc_readl(MISC_SERDES_CTRL_REG);
+	if (BCMCPU_IS_6328())
+		reg = MISC_SERDES_CTRL_6328_REG;
+	else
+		reg = MISC_SERDES_CTRL_6362_REG;
+
+	val = bcm_misc_readl(reg);
 	val |= SERDES_PCIE_EN | SERDES_PCIE_EXD_EN;
-	bcm_misc_writel(val, MISC_SERDES_CTRL_REG);
+	bcm_misc_writel(val, reg);
 
 	/* reset the PCIe core */
 	bcm63xx_core_set_reset(BCM63XX_RESET_PCIE, 1);
@@ -330,6 +336,7 @@ static int __init bcm63xx_pci_init(void)
 
 	switch (bcm63xx_get_cpu_id()) {
 	case BCM6328_CPU_ID:
+	case BCM6362_CPU_ID:
 		return bcm63xx_register_pcie();
 	case BCM6348_CPU_ID:
 	case BCM6358_CPU_ID:
-- 
1.7.10.4

[PATCH 7/7] MIPS: BCM63XX: add flash detection for BCM6362

[Jonas Gorski]

BCM6362 support booting from SPI flash and NAND.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
---
 arch/mips/bcm63xx/dev-flash.c                     |    6 ++++++
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h |    1 +
 2 files changed, 7 insertions(+)

diff --git a/arch/mips/bcm63xx/dev-flash.c b/arch/mips/bcm63xx/dev-flash.c
index 58371c7..588d1ec 100644
--- a/arch/mips/bcm63xx/dev-flash.c
+++ b/arch/mips/bcm63xx/dev-flash.c
@@ -77,6 +77,12 @@ static int __init bcm63xx_detect_flash_type(void)
 			return BCM63XX_FLASH_TYPE_PARALLEL;
 		else
 			return BCM63XX_FLASH_TYPE_SERIAL;
+	case BCM6362_CPU_ID:
+		val = bcm_misc_readl(MISC_STRAPBUS_6362_REG);
+		if (val & STRAPBUS_6362_BOOT_SEL_SERIAL)
+			return BCM63XX_FLASH_TYPE_SERIAL;
+		else
+			return BCM63XX_FLASH_TYPE_NAND;
 	case BCM6368_CPU_ID:
 		val = bcm_gpio_readl(GPIO_STRAPBUS_REG);
 		switch (val & STRAPBUS_6368_BOOT_SEL_MASK) {
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
index 243bab9..3203fe4 100644
--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
@@ -1372,6 +1372,7 @@
 
 #define MISC_STRAPBUS_6362_REG		0x14
 #define STRAPBUS_6362_FCVO_SHIFT	1
+#define STRAPBUS_6362_HSSPI_CLK_FAST	(1 << 13)
 #define STRAPBUS_6362_FCVO_MASK		(0x1f << STRAPBUS_6362_FCVO_SHIFT)
 #define STRAPBUS_6362_BOOT_SEL_SERIAL	(1 << 15)
 #define STRAPBUS_6362_BOOT_SEL_NAND	(0 << 15)
-- 
1.7.10.4

Re: [PATCH 0/7] add basic support for BCM6362

[Florian Fainelli]

Le 03/21/13 16:00, Jonas Gorski a écrit :
> This patchset adds basic support for BCM6362. BCM6362 includes a 9 port
> ethernet switch (4 FE PHYs, 2 RGMII ports), integrated wifi and one PCIe
> port.
>
> The first few patches do a bit of clean up first to allow the BCM6362
> support code to be as small as possible.
>
> Board definitions were left out as they are not really usable yet, and
> adding DT support is planned in the future. Most code added here will
> be also required with DT support.
>
> Jonas Gorski (7):
>    MIPS: BCM63XX: remove duplicate spi register definitions
>    MIPS: BCM63XX: fix revision ID width
>    MIPS: BCM63XX: rework chip detection
>    MIPS: BCM63XX: add basic BCM6362 support
>    MIPS: BCM63XX: enable SPI controller for BCM6362
>    MIPS: BCM63XX: enable pcie for BCM6362
>    MIPS: BCM63XX: add flash detection for BCM6362

For this serie:
Acked-by: Florian Fainelli <florian@openwrt.org>

Thanks Jonas!
--
Florian