* [PATCH V2] ARM: tegra: enable palmas device for dalmore
@ 2013-07-10 7:37 ` Laxman Dewangan
0 siblings, 0 replies; 21+ messages in thread
From: Laxman Dewangan @ 2013-07-10 7:37 UTC (permalink / raw)
To: swarren-3lzwWm7+Weoh9ZMKESR00Q
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-tegra-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Laxman Dewangan
Make the entry of Dalmore Power Management Unit device TPS65913
in dalmore DTS file. The Palma driver support this device.
Enable following submodule of the TPS65913:
- GPIO driver
- RTC driver.
- Power regulator driver.
Signed-off-by: Laxman Dewangan <ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
---
Changes from V1:
- renames nodes from palams_* to simple as gpio, rtc, pmic etc.
- Added line gap properly.
- Remove comment for palams-gpio reference as the entry itself explain.
- Remove unit address for tps65913.
arch/arm/boot/dts/tegra114-dalmore.dts | 184 +++++++++++++++++++++++++++++++-
1 files changed, 183 insertions(+), 1 deletions(-)
diff --git a/arch/arm/boot/dts/tegra114-dalmore.dts b/arch/arm/boot/dts/tegra114-dalmore.dts
index a42bfa4..7bdad77 100644
--- a/arch/arm/boot/dts/tegra114-dalmore.dts
+++ b/arch/arm/boot/dts/tegra114-dalmore.dts
@@ -791,7 +791,7 @@
regulator-boot-on;
};
- dcdc3 {
+ tps65090_dcdc3_reg: dcdc3 {
regulator-name = "vdd-ao";
regulator-always-on;
regulator-boot-on;
@@ -836,6 +836,178 @@
};
};
};
+
+ palmas: tps65913 {
+ compatible = "ti,palmas";
+ reg = <0x58>;
+ interrupts = <0 86 0x4>;
+
+ #interrupt-cells = <2>;
+ interrupt-controller;
+
+ palmas_gpio: gpio {
+ compatible = "ti,palmas-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ rtc {
+ compatible = "ti,palmas-rtc";
+ interrupt-parent = <&palmas>;
+ interrupts = <8 0>;
+ };
+
+ pmic {
+ compatible = "ti,tps65913-pmic", "ti,palmas-pmic";
+ smps1-in-supply = <&tps65090_dcdc3_reg>;
+ smps3-in-supply = <&tps65090_dcdc3_reg>;
+ smps4-in-supply = <&tps65090_dcdc2_reg>;
+ smps7-in-supply = <&tps65090_dcdc2_reg>;
+ smps8-in-supply = <&tps65090_dcdc2_reg>;
+ smps9-in-supply = <&tps65090_dcdc2_reg>;
+ ldo1-in-supply = <&tps65090_dcdc2_reg>;
+ ldo2-in-supply = <&tps65090_dcdc2_reg>;
+ ldo3-in-supply = <&palmas_smps3_reg>;
+ ldo4-in-supply = <&tps65090_dcdc2_reg>;
+ ldo5-in-supply = <&vdd_ac_bat_reg>;
+ ldo6-in-supply = <&tps65090_dcdc2_reg>;
+ ldo7-in-supply = <&tps65090_dcdc2_reg>;
+ ldo8-in-supply = <&tps65090_dcdc3_reg>;
+ ldo9-in-supply = <&palmas_smps9_reg>;
+ ldoln-in-supply = <&tps65090_dcdc1_reg>;
+ ldousb-in-supply = <&tps65090_dcdc1_reg>;
+
+ regulators {
+ smps12 {
+ regulator-name = "vddio-ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ palmas_smps3_reg: smps3 {
+ regulator-name = "vddio-1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps45 {
+ regulator-name = "vdd-core";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps457 {
+ regulator-name = "vdd-core";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps8 {
+ regulator-name = "avdd-pll";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ palmas_smps9_reg: smps9 {
+ regulator-name = "sdhci-vdd-sd-slot";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ ldo1 {
+ regulator-name = "avdd-cam1";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo2 {
+ regulator-name = "avdd-cam2";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo3 {
+ regulator-name = "avdd-dsi-csi";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo4 {
+ regulator-name = "vpp-fuse";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo6 {
+ regulator-name = "vdd-sensor-2v85";
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ ldo7 {
+ regulator-name = "vdd-af-cam1";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo8 {
+ regulator-name = "vdd-rtc";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-always-on;
+ regulator-boot-on;
+ ti,enable-ldo8-tracking;
+ };
+
+ ldo9 {
+ regulator-name = "vddio-sdmmc-2";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldoln {
+ regulator-name = "hvdd-usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldousb {
+ regulator-name = "avdd-usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ regen1 {
+ regulator-name = "rail-3v3";
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ regen2 {
+ regulator-name = "rail-5v0";
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+ };
};
spi@7000da00 {
@@ -980,6 +1152,16 @@
gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
vin-supply = <&tps65090_dcdc1_reg>;
};
+
+ vdd_cam_1v8_reg: regulator@6 {
+ compatible = "regulator-fixed";
+ reg = <6>;
+ regulator-name = "vdd_cam_1v8_reg";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ enable-active-high;
+ gpio = <&palmas_gpio 6 0>;
+ };
};
sound {
--
1.7.1.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH V2] ARM: tegra: enable palmas device for dalmore
@ 2013-07-10 7:37 ` Laxman Dewangan
0 siblings, 0 replies; 21+ messages in thread
From: Laxman Dewangan @ 2013-07-10 7:37 UTC (permalink / raw)
To: swarren; +Cc: linux-arm-kernel, linux-tegra, linux-kernel, Laxman Dewangan
Make the entry of Dalmore Power Management Unit device TPS65913
in dalmore DTS file. The Palma driver support this device.
Enable following submodule of the TPS65913:
- GPIO driver
- RTC driver.
- Power regulator driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
---
Changes from V1:
- renames nodes from palams_* to simple as gpio, rtc, pmic etc.
- Added line gap properly.
- Remove comment for palams-gpio reference as the entry itself explain.
- Remove unit address for tps65913.
arch/arm/boot/dts/tegra114-dalmore.dts | 184 +++++++++++++++++++++++++++++++-
1 files changed, 183 insertions(+), 1 deletions(-)
diff --git a/arch/arm/boot/dts/tegra114-dalmore.dts b/arch/arm/boot/dts/tegra114-dalmore.dts
index a42bfa4..7bdad77 100644
--- a/arch/arm/boot/dts/tegra114-dalmore.dts
+++ b/arch/arm/boot/dts/tegra114-dalmore.dts
@@ -791,7 +791,7 @@
regulator-boot-on;
};
- dcdc3 {
+ tps65090_dcdc3_reg: dcdc3 {
regulator-name = "vdd-ao";
regulator-always-on;
regulator-boot-on;
@@ -836,6 +836,178 @@
};
};
};
+
+ palmas: tps65913 {
+ compatible = "ti,palmas";
+ reg = <0x58>;
+ interrupts = <0 86 0x4>;
+
+ #interrupt-cells = <2>;
+ interrupt-controller;
+
+ palmas_gpio: gpio {
+ compatible = "ti,palmas-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ rtc {
+ compatible = "ti,palmas-rtc";
+ interrupt-parent = <&palmas>;
+ interrupts = <8 0>;
+ };
+
+ pmic {
+ compatible = "ti,tps65913-pmic", "ti,palmas-pmic";
+ smps1-in-supply = <&tps65090_dcdc3_reg>;
+ smps3-in-supply = <&tps65090_dcdc3_reg>;
+ smps4-in-supply = <&tps65090_dcdc2_reg>;
+ smps7-in-supply = <&tps65090_dcdc2_reg>;
+ smps8-in-supply = <&tps65090_dcdc2_reg>;
+ smps9-in-supply = <&tps65090_dcdc2_reg>;
+ ldo1-in-supply = <&tps65090_dcdc2_reg>;
+ ldo2-in-supply = <&tps65090_dcdc2_reg>;
+ ldo3-in-supply = <&palmas_smps3_reg>;
+ ldo4-in-supply = <&tps65090_dcdc2_reg>;
+ ldo5-in-supply = <&vdd_ac_bat_reg>;
+ ldo6-in-supply = <&tps65090_dcdc2_reg>;
+ ldo7-in-supply = <&tps65090_dcdc2_reg>;
+ ldo8-in-supply = <&tps65090_dcdc3_reg>;
+ ldo9-in-supply = <&palmas_smps9_reg>;
+ ldoln-in-supply = <&tps65090_dcdc1_reg>;
+ ldousb-in-supply = <&tps65090_dcdc1_reg>;
+
+ regulators {
+ smps12 {
+ regulator-name = "vddio-ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ palmas_smps3_reg: smps3 {
+ regulator-name = "vddio-1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps45 {
+ regulator-name = "vdd-core";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps457 {
+ regulator-name = "vdd-core";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps8 {
+ regulator-name = "avdd-pll";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ palmas_smps9_reg: smps9 {
+ regulator-name = "sdhci-vdd-sd-slot";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ ldo1 {
+ regulator-name = "avdd-cam1";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo2 {
+ regulator-name = "avdd-cam2";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo3 {
+ regulator-name = "avdd-dsi-csi";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo4 {
+ regulator-name = "vpp-fuse";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo6 {
+ regulator-name = "vdd-sensor-2v85";
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ ldo7 {
+ regulator-name = "vdd-af-cam1";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo8 {
+ regulator-name = "vdd-rtc";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-always-on;
+ regulator-boot-on;
+ ti,enable-ldo8-tracking;
+ };
+
+ ldo9 {
+ regulator-name = "vddio-sdmmc-2";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldoln {
+ regulator-name = "hvdd-usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldousb {
+ regulator-name = "avdd-usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ regen1 {
+ regulator-name = "rail-3v3";
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ regen2 {
+ regulator-name = "rail-5v0";
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+ };
};
spi@7000da00 {
@@ -980,6 +1152,16 @@
gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
vin-supply = <&tps65090_dcdc1_reg>;
};
+
+ vdd_cam_1v8_reg: regulator@6 {
+ compatible = "regulator-fixed";
+ reg = <6>;
+ regulator-name = "vdd_cam_1v8_reg";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ enable-active-high;
+ gpio = <&palmas_gpio 6 0>;
+ };
};
sound {
--
1.7.1.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH V2] ARM: tegra: enable palmas device for dalmore
@ 2013-07-10 7:37 ` Laxman Dewangan
0 siblings, 0 replies; 21+ messages in thread
From: Laxman Dewangan @ 2013-07-10 7:37 UTC (permalink / raw)
To: linux-arm-kernel
Make the entry of Dalmore Power Management Unit device TPS65913
in dalmore DTS file. The Palma driver support this device.
Enable following submodule of the TPS65913:
- GPIO driver
- RTC driver.
- Power regulator driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
---
Changes from V1:
- renames nodes from palams_* to simple as gpio, rtc, pmic etc.
- Added line gap properly.
- Remove comment for palams-gpio reference as the entry itself explain.
- Remove unit address for tps65913.
arch/arm/boot/dts/tegra114-dalmore.dts | 184 +++++++++++++++++++++++++++++++-
1 files changed, 183 insertions(+), 1 deletions(-)
diff --git a/arch/arm/boot/dts/tegra114-dalmore.dts b/arch/arm/boot/dts/tegra114-dalmore.dts
index a42bfa4..7bdad77 100644
--- a/arch/arm/boot/dts/tegra114-dalmore.dts
+++ b/arch/arm/boot/dts/tegra114-dalmore.dts
@@ -791,7 +791,7 @@
regulator-boot-on;
};
- dcdc3 {
+ tps65090_dcdc3_reg: dcdc3 {
regulator-name = "vdd-ao";
regulator-always-on;
regulator-boot-on;
@@ -836,6 +836,178 @@
};
};
};
+
+ palmas: tps65913 {
+ compatible = "ti,palmas";
+ reg = <0x58>;
+ interrupts = <0 86 0x4>;
+
+ #interrupt-cells = <2>;
+ interrupt-controller;
+
+ palmas_gpio: gpio {
+ compatible = "ti,palmas-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ rtc {
+ compatible = "ti,palmas-rtc";
+ interrupt-parent = <&palmas>;
+ interrupts = <8 0>;
+ };
+
+ pmic {
+ compatible = "ti,tps65913-pmic", "ti,palmas-pmic";
+ smps1-in-supply = <&tps65090_dcdc3_reg>;
+ smps3-in-supply = <&tps65090_dcdc3_reg>;
+ smps4-in-supply = <&tps65090_dcdc2_reg>;
+ smps7-in-supply = <&tps65090_dcdc2_reg>;
+ smps8-in-supply = <&tps65090_dcdc2_reg>;
+ smps9-in-supply = <&tps65090_dcdc2_reg>;
+ ldo1-in-supply = <&tps65090_dcdc2_reg>;
+ ldo2-in-supply = <&tps65090_dcdc2_reg>;
+ ldo3-in-supply = <&palmas_smps3_reg>;
+ ldo4-in-supply = <&tps65090_dcdc2_reg>;
+ ldo5-in-supply = <&vdd_ac_bat_reg>;
+ ldo6-in-supply = <&tps65090_dcdc2_reg>;
+ ldo7-in-supply = <&tps65090_dcdc2_reg>;
+ ldo8-in-supply = <&tps65090_dcdc3_reg>;
+ ldo9-in-supply = <&palmas_smps9_reg>;
+ ldoln-in-supply = <&tps65090_dcdc1_reg>;
+ ldousb-in-supply = <&tps65090_dcdc1_reg>;
+
+ regulators {
+ smps12 {
+ regulator-name = "vddio-ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ palmas_smps3_reg: smps3 {
+ regulator-name = "vddio-1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps45 {
+ regulator-name = "vdd-core";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps457 {
+ regulator-name = "vdd-core";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps8 {
+ regulator-name = "avdd-pll";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ palmas_smps9_reg: smps9 {
+ regulator-name = "sdhci-vdd-sd-slot";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ ldo1 {
+ regulator-name = "avdd-cam1";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo2 {
+ regulator-name = "avdd-cam2";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo3 {
+ regulator-name = "avdd-dsi-csi";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo4 {
+ regulator-name = "vpp-fuse";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo6 {
+ regulator-name = "vdd-sensor-2v85";
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ ldo7 {
+ regulator-name = "vdd-af-cam1";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo8 {
+ regulator-name = "vdd-rtc";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-always-on;
+ regulator-boot-on;
+ ti,enable-ldo8-tracking;
+ };
+
+ ldo9 {
+ regulator-name = "vddio-sdmmc-2";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldoln {
+ regulator-name = "hvdd-usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldousb {
+ regulator-name = "avdd-usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ regen1 {
+ regulator-name = "rail-3v3";
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ regen2 {
+ regulator-name = "rail-5v0";
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+ };
};
spi at 7000da00 {
@@ -980,6 +1152,16 @@
gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
vin-supply = <&tps65090_dcdc1_reg>;
};
+
+ vdd_cam_1v8_reg: regulator at 6 {
+ compatible = "regulator-fixed";
+ reg = <6>;
+ regulator-name = "vdd_cam_1v8_reg";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ enable-active-high;
+ gpio = <&palmas_gpio 6 0>;
+ };
};
sound {
--
1.7.1.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* Re: [PATCH V2] ARM: tegra: enable palmas device for dalmore
2013-07-10 7:37 ` Laxman Dewangan
(?)
@ 2013-07-15 16:48 ` Stephen Warren
-1 siblings, 0 replies; 21+ messages in thread
From: Stephen Warren @ 2013-07-15 16:48 UTC (permalink / raw)
To: Laxman Dewangan
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-tegra-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
On 07/10/2013 01:37 AM, Laxman Dewangan wrote:
> Make the entry of Dalmore Power Management Unit device TPS65913
> in dalmore DTS file. The Palma driver support this device.
>
> Enable following submodule of the TPS65913:
> - GPIO driver
> - RTC driver.
> - Power regulator driver.
If I apply this, (at least) the SD card no longer works. I assume the
regulator for it is being turned off somehow.
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH V2] ARM: tegra: enable palmas device for dalmore
@ 2013-07-15 16:48 ` Stephen Warren
0 siblings, 0 replies; 21+ messages in thread
From: Stephen Warren @ 2013-07-15 16:48 UTC (permalink / raw)
To: Laxman Dewangan; +Cc: linux-arm-kernel, linux-tegra, linux-kernel
On 07/10/2013 01:37 AM, Laxman Dewangan wrote:
> Make the entry of Dalmore Power Management Unit device TPS65913
> in dalmore DTS file. The Palma driver support this device.
>
> Enable following submodule of the TPS65913:
> - GPIO driver
> - RTC driver.
> - Power regulator driver.
If I apply this, (at least) the SD card no longer works. I assume the
regulator for it is being turned off somehow.
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH V2] ARM: tegra: enable palmas device for dalmore
@ 2013-07-15 16:48 ` Stephen Warren
0 siblings, 0 replies; 21+ messages in thread
From: Stephen Warren @ 2013-07-15 16:48 UTC (permalink / raw)
To: linux-arm-kernel
On 07/10/2013 01:37 AM, Laxman Dewangan wrote:
> Make the entry of Dalmore Power Management Unit device TPS65913
> in dalmore DTS file. The Palma driver support this device.
>
> Enable following submodule of the TPS65913:
> - GPIO driver
> - RTC driver.
> - Power regulator driver.
If I apply this, (at least) the SD card no longer works. I assume the
regulator for it is being turned off somehow.
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH V2] ARM: tegra: enable palmas device for dalmore
2013-07-15 16:48 ` Stephen Warren
(?)
@ 2013-07-15 17:28 ` Laxman Dewangan
-1 siblings, 0 replies; 21+ messages in thread
From: Laxman Dewangan @ 2013-07-15 17:28 UTC (permalink / raw)
To: Stephen Warren, Rhyland Klein
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-tegra-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
On Monday 15 July 2013 10:18 PM, Stephen Warren wrote:
> On 07/10/2013 01:37 AM, Laxman Dewangan wrote:
>> Make the entry of Dalmore Power Management Unit device TPS65913
>> in dalmore DTS file. The Palma driver support this device.
>>
>> Enable following submodule of the TPS65913:
>> - GPIO driver
>> - RTC driver.
>> - Power regulator driver.
> If I apply this, (at least) the SD card no longer works. I assume the
> regulator for it is being turned off somehow.
As per downstream power tree, smps9 is feeding power to sd slot and I
make this rail as always ON. So there should not be any issue.
Rhyland,
Do you see any differences on this power tree with your power tree with
DT? There was discussion sometime ago on the sdcard. Am I missing
anything here?
Thanks,
Laxman
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH V2] ARM: tegra: enable palmas device for dalmore
@ 2013-07-15 17:28 ` Laxman Dewangan
0 siblings, 0 replies; 21+ messages in thread
From: Laxman Dewangan @ 2013-07-15 17:28 UTC (permalink / raw)
To: Stephen Warren, Rhyland Klein; +Cc: linux-arm-kernel, linux-tegra, linux-kernel
On Monday 15 July 2013 10:18 PM, Stephen Warren wrote:
> On 07/10/2013 01:37 AM, Laxman Dewangan wrote:
>> Make the entry of Dalmore Power Management Unit device TPS65913
>> in dalmore DTS file. The Palma driver support this device.
>>
>> Enable following submodule of the TPS65913:
>> - GPIO driver
>> - RTC driver.
>> - Power regulator driver.
> If I apply this, (at least) the SD card no longer works. I assume the
> regulator for it is being turned off somehow.
As per downstream power tree, smps9 is feeding power to sd slot and I
make this rail as always ON. So there should not be any issue.
Rhyland,
Do you see any differences on this power tree with your power tree with
DT? There was discussion sometime ago on the sdcard. Am I missing
anything here?
Thanks,
Laxman
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH V2] ARM: tegra: enable palmas device for dalmore
@ 2013-07-15 17:28 ` Laxman Dewangan
0 siblings, 0 replies; 21+ messages in thread
From: Laxman Dewangan @ 2013-07-15 17:28 UTC (permalink / raw)
To: linux-arm-kernel
On Monday 15 July 2013 10:18 PM, Stephen Warren wrote:
> On 07/10/2013 01:37 AM, Laxman Dewangan wrote:
>> Make the entry of Dalmore Power Management Unit device TPS65913
>> in dalmore DTS file. The Palma driver support this device.
>>
>> Enable following submodule of the TPS65913:
>> - GPIO driver
>> - RTC driver.
>> - Power regulator driver.
> If I apply this, (at least) the SD card no longer works. I assume the
> regulator for it is being turned off somehow.
As per downstream power tree, smps9 is feeding power to sd slot and I
make this rail as always ON. So there should not be any issue.
Rhyland,
Do you see any differences on this power tree with your power tree with
DT? There was discussion sometime ago on the sdcard. Am I missing
anything here?
Thanks,
Laxman
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH V2] ARM: tegra: enable palmas device for dalmore
2013-07-15 17:28 ` Laxman Dewangan
(?)
@ 2013-07-15 17:29 ` Rhyland Klein
-1 siblings, 0 replies; 21+ messages in thread
From: Rhyland Klein @ 2013-07-15 17:29 UTC (permalink / raw)
To: Laxman Dewangan
Cc: Stephen Warren,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-tegra-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
On 7/15/2013 1:28 PM, Laxman Dewangan wrote:
> On Monday 15 July 2013 10:18 PM, Stephen Warren wrote:
>> On 07/10/2013 01:37 AM, Laxman Dewangan wrote:
>>> Make the entry of Dalmore Power Management Unit device TPS65913
>>> in dalmore DTS file. The Palma driver support this device.
>>>
>>> Enable following submodule of the TPS65913:
>>> - GPIO driver
>>> - RTC driver.
>>> - Power regulator driver.
>> If I apply this, (at least) the SD card no longer works. I assume the
>> regulator for it is being turned off somehow.
>
> As per downstream power tree, smps9 is feeding power to sd slot and I
> make this rail as always ON. So there should not be any issue.
>
> Rhyland,
> Do you see any differences on this power tree with your power tree with
> DT? There was discussion sometime ago on the sdcard. Am I missing
> anything here?
>
> Thanks,
> Laxman
>
I noticed a couple differences between this and what we are using...
Yours:
+ ldo8-in-supply = <&tps65090_dcdc3_reg>;
+ ldo9-in-supply = <&palmas_smps9_reg>;
Ours:
ldo8-in-supply = <&tps65090_dcdc2_reg>;
ldo9-in-supply = <&tps65090_dcdc2_reg>;
We also specify supplies (floating) for smps6 and smps10. I don't think
that matters though.
Also we have the vmmc-supply and sd-slot-supply propeties set for the sd
card slot, like so:
vmmc-supply = <&palmas_smps3_reg>;
sd-slot-supply = <&palmas_smps9_reg>;
Also, we have the interrupt trigger mode different for the palmas:
Yours:
+ interrupts = <0 86 0x4>;
Ours:
interrupts = <0 86 0x8>;
I think other than that they should be the same.
-Rhyland
--
nvpublic
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH V2] ARM: tegra: enable palmas device for dalmore
@ 2013-07-15 17:29 ` Rhyland Klein
0 siblings, 0 replies; 21+ messages in thread
From: Rhyland Klein @ 2013-07-15 17:29 UTC (permalink / raw)
To: Laxman Dewangan
Cc: Stephen Warren, linux-arm-kernel, linux-tegra, linux-kernel
On 7/15/2013 1:28 PM, Laxman Dewangan wrote:
> On Monday 15 July 2013 10:18 PM, Stephen Warren wrote:
>> On 07/10/2013 01:37 AM, Laxman Dewangan wrote:
>>> Make the entry of Dalmore Power Management Unit device TPS65913
>>> in dalmore DTS file. The Palma driver support this device.
>>>
>>> Enable following submodule of the TPS65913:
>>> - GPIO driver
>>> - RTC driver.
>>> - Power regulator driver.
>> If I apply this, (at least) the SD card no longer works. I assume the
>> regulator for it is being turned off somehow.
>
> As per downstream power tree, smps9 is feeding power to sd slot and I
> make this rail as always ON. So there should not be any issue.
>
> Rhyland,
> Do you see any differences on this power tree with your power tree with
> DT? There was discussion sometime ago on the sdcard. Am I missing
> anything here?
>
> Thanks,
> Laxman
>
I noticed a couple differences between this and what we are using...
Yours:
+ ldo8-in-supply = <&tps65090_dcdc3_reg>;
+ ldo9-in-supply = <&palmas_smps9_reg>;
Ours:
ldo8-in-supply = <&tps65090_dcdc2_reg>;
ldo9-in-supply = <&tps65090_dcdc2_reg>;
We also specify supplies (floating) for smps6 and smps10. I don't think
that matters though.
Also we have the vmmc-supply and sd-slot-supply propeties set for the sd
card slot, like so:
vmmc-supply = <&palmas_smps3_reg>;
sd-slot-supply = <&palmas_smps9_reg>;
Also, we have the interrupt trigger mode different for the palmas:
Yours:
+ interrupts = <0 86 0x4>;
Ours:
interrupts = <0 86 0x8>;
I think other than that they should be the same.
-Rhyland
--
nvpublic
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH V2] ARM: tegra: enable palmas device for dalmore
@ 2013-07-15 17:29 ` Rhyland Klein
0 siblings, 0 replies; 21+ messages in thread
From: Rhyland Klein @ 2013-07-15 17:29 UTC (permalink / raw)
To: linux-arm-kernel
On 7/15/2013 1:28 PM, Laxman Dewangan wrote:
> On Monday 15 July 2013 10:18 PM, Stephen Warren wrote:
>> On 07/10/2013 01:37 AM, Laxman Dewangan wrote:
>>> Make the entry of Dalmore Power Management Unit device TPS65913
>>> in dalmore DTS file. The Palma driver support this device.
>>>
>>> Enable following submodule of the TPS65913:
>>> - GPIO driver
>>> - RTC driver.
>>> - Power regulator driver.
>> If I apply this, (at least) the SD card no longer works. I assume the
>> regulator for it is being turned off somehow.
>
> As per downstream power tree, smps9 is feeding power to sd slot and I
> make this rail as always ON. So there should not be any issue.
>
> Rhyland,
> Do you see any differences on this power tree with your power tree with
> DT? There was discussion sometime ago on the sdcard. Am I missing
> anything here?
>
> Thanks,
> Laxman
>
I noticed a couple differences between this and what we are using...
Yours:
+ ldo8-in-supply = <&tps65090_dcdc3_reg>;
+ ldo9-in-supply = <&palmas_smps9_reg>;
Ours:
ldo8-in-supply = <&tps65090_dcdc2_reg>;
ldo9-in-supply = <&tps65090_dcdc2_reg>;
We also specify supplies (floating) for smps6 and smps10. I don't think
that matters though.
Also we have the vmmc-supply and sd-slot-supply propeties set for the sd
card slot, like so:
vmmc-supply = <&palmas_smps3_reg>;
sd-slot-supply = <&palmas_smps9_reg>;
Also, we have the interrupt trigger mode different for the palmas:
Yours:
+ interrupts = <0 86 0x4>;
Ours:
interrupts = <0 86 0x8>;
I think other than that they should be the same.
-Rhyland
--
nvpublic
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH V2] ARM: tegra: enable palmas device for dalmore
2013-07-10 7:37 ` Laxman Dewangan
(?)
@ 2013-07-16 13:51 ` Mikko Perttunen
-1 siblings, 0 replies; 21+ messages in thread
From: Mikko Perttunen @ 2013-07-16 13:51 UTC (permalink / raw)
To: Laxman Dewangan
Cc: swarren-3lzwWm7+Weoh9ZMKESR00Q,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-tegra-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
On 07/10/2013 10:37 AM, Laxman Dewangan wrote:
> Make the entry of Dalmore Power Management Unit device TPS65913
> in dalmore DTS file. The Palma driver support this device.
>
> Enable following submodule of the TPS65913:
> - GPIO driver
> - RTC driver.
> - Power regulator driver.
>
> Signed-off-by: Laxman Dewangan <ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
> ---
> Changes from V1:
> - renames nodes from palams_* to simple as gpio, rtc, pmic etc.
> - Added line gap properly.
> - Remove comment for palams-gpio reference as the entry itself explain.
> - Remove unit address for tps65913.
>
> arch/arm/boot/dts/tegra114-dalmore.dts | 184 +++++++++++++++++++++++++++++++-
> 1 files changed, 183 insertions(+), 1 deletions(-)
>
> diff --git a/arch/arm/boot/dts/tegra114-dalmore.dts b/arch/arm/boot/dts/tegra114-dalmore.dts
> index a42bfa4..7bdad77 100644
> --- a/arch/arm/boot/dts/tegra114-dalmore.dts
> +++ b/arch/arm/boot/dts/tegra114-dalmore.dts
> @@ -791,7 +791,7 @@
> regulator-boot-on;
> };
>
> - dcdc3 {
> + tps65090_dcdc3_reg: dcdc3 {
> regulator-name = "vdd-ao";
> regulator-always-on;
> regulator-boot-on;
> @@ -836,6 +836,178 @@
> };
> };
> };
> +
> + palmas: tps65913 {
> + compatible = "ti,palmas";
> + reg = <0x58>;
> + interrupts = <0 86 0x4>;
> +
> + #interrupt-cells = <2>;
> + interrupt-controller;
> +
> + palmas_gpio: gpio {
> + compatible = "ti,palmas-gpio";
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
I don't think the palmas-gpio driver ever gets probed since it doesn't
have device tree compability strings?
> ...
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH V2] ARM: tegra: enable palmas device for dalmore
@ 2013-07-16 13:51 ` Mikko Perttunen
0 siblings, 0 replies; 21+ messages in thread
From: Mikko Perttunen @ 2013-07-16 13:51 UTC (permalink / raw)
To: Laxman Dewangan; +Cc: swarren, linux-arm-kernel, linux-tegra, linux-kernel
On 07/10/2013 10:37 AM, Laxman Dewangan wrote:
> Make the entry of Dalmore Power Management Unit device TPS65913
> in dalmore DTS file. The Palma driver support this device.
>
> Enable following submodule of the TPS65913:
> - GPIO driver
> - RTC driver.
> - Power regulator driver.
>
> Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
> ---
> Changes from V1:
> - renames nodes from palams_* to simple as gpio, rtc, pmic etc.
> - Added line gap properly.
> - Remove comment for palams-gpio reference as the entry itself explain.
> - Remove unit address for tps65913.
>
> arch/arm/boot/dts/tegra114-dalmore.dts | 184 +++++++++++++++++++++++++++++++-
> 1 files changed, 183 insertions(+), 1 deletions(-)
>
> diff --git a/arch/arm/boot/dts/tegra114-dalmore.dts b/arch/arm/boot/dts/tegra114-dalmore.dts
> index a42bfa4..7bdad77 100644
> --- a/arch/arm/boot/dts/tegra114-dalmore.dts
> +++ b/arch/arm/boot/dts/tegra114-dalmore.dts
> @@ -791,7 +791,7 @@
> regulator-boot-on;
> };
>
> - dcdc3 {
> + tps65090_dcdc3_reg: dcdc3 {
> regulator-name = "vdd-ao";
> regulator-always-on;
> regulator-boot-on;
> @@ -836,6 +836,178 @@
> };
> };
> };
> +
> + palmas: tps65913 {
> + compatible = "ti,palmas";
> + reg = <0x58>;
> + interrupts = <0 86 0x4>;
> +
> + #interrupt-cells = <2>;
> + interrupt-controller;
> +
> + palmas_gpio: gpio {
> + compatible = "ti,palmas-gpio";
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
I don't think the palmas-gpio driver ever gets probed since it doesn't
have device tree compability strings?
> ...
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH V2] ARM: tegra: enable palmas device for dalmore
@ 2013-07-16 13:51 ` Mikko Perttunen
0 siblings, 0 replies; 21+ messages in thread
From: Mikko Perttunen @ 2013-07-16 13:51 UTC (permalink / raw)
To: linux-arm-kernel
On 07/10/2013 10:37 AM, Laxman Dewangan wrote:
> Make the entry of Dalmore Power Management Unit device TPS65913
> in dalmore DTS file. The Palma driver support this device.
>
> Enable following submodule of the TPS65913:
> - GPIO driver
> - RTC driver.
> - Power regulator driver.
>
> Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
> ---
> Changes from V1:
> - renames nodes from palams_* to simple as gpio, rtc, pmic etc.
> - Added line gap properly.
> - Remove comment for palams-gpio reference as the entry itself explain.
> - Remove unit address for tps65913.
>
> arch/arm/boot/dts/tegra114-dalmore.dts | 184 +++++++++++++++++++++++++++++++-
> 1 files changed, 183 insertions(+), 1 deletions(-)
>
> diff --git a/arch/arm/boot/dts/tegra114-dalmore.dts b/arch/arm/boot/dts/tegra114-dalmore.dts
> index a42bfa4..7bdad77 100644
> --- a/arch/arm/boot/dts/tegra114-dalmore.dts
> +++ b/arch/arm/boot/dts/tegra114-dalmore.dts
> @@ -791,7 +791,7 @@
> regulator-boot-on;
> };
>
> - dcdc3 {
> + tps65090_dcdc3_reg: dcdc3 {
> regulator-name = "vdd-ao";
> regulator-always-on;
> regulator-boot-on;
> @@ -836,6 +836,178 @@
> };
> };
> };
> +
> + palmas: tps65913 {
> + compatible = "ti,palmas";
> + reg = <0x58>;
> + interrupts = <0 86 0x4>;
> +
> + #interrupt-cells = <2>;
> + interrupt-controller;
> +
> + palmas_gpio: gpio {
> + compatible = "ti,palmas-gpio";
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
I don't think the palmas-gpio driver ever gets probed since it doesn't
have device tree compability strings?
> ...
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH V2] ARM: tegra: enable palmas device for dalmore
2013-07-17 8:57 ` Laxman Dewangan
(?)
@ 2013-07-17 8:53 ` Mikko Perttunen
-1 siblings, 0 replies; 21+ messages in thread
From: Mikko Perttunen @ 2013-07-17 8:53 UTC (permalink / raw)
To: Laxman Dewangan
Cc: swarren-3lzwWm7+Weoh9ZMKESR00Q,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-tegra-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
On 07/17/2013 11:57 AM, Laxman Dewangan wrote:
> On Tuesday 16 July 2013 07:21 PM, Mikko Perttunen wrote:
>> On 07/10/2013 10:37 AM, Laxman Dewangan wrote:
>>> +
>>> + palmas_gpio: gpio {
>>> + compatible = "ti,palmas-gpio";
>>> + gpio-controller;
>>> + #gpio-cells = <2>;
>>> + };
>> I don't think the palmas-gpio driver ever gets probed since it doesn't
>> have device tree compability strings?
>>
> You will need the patch
> [PATCH V3] gpio: palmas: add dt support
>
> which is under review from last few days.
>
Ah, ok. I guess I'm not on the proper ML for that one.
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH V2] ARM: tegra: enable palmas device for dalmore
@ 2013-07-17 8:53 ` Mikko Perttunen
0 siblings, 0 replies; 21+ messages in thread
From: Mikko Perttunen @ 2013-07-17 8:53 UTC (permalink / raw)
To: Laxman Dewangan; +Cc: swarren, linux-arm-kernel, linux-tegra, linux-kernel
On 07/17/2013 11:57 AM, Laxman Dewangan wrote:
> On Tuesday 16 July 2013 07:21 PM, Mikko Perttunen wrote:
>> On 07/10/2013 10:37 AM, Laxman Dewangan wrote:
>>> +
>>> + palmas_gpio: gpio {
>>> + compatible = "ti,palmas-gpio";
>>> + gpio-controller;
>>> + #gpio-cells = <2>;
>>> + };
>> I don't think the palmas-gpio driver ever gets probed since it doesn't
>> have device tree compability strings?
>>
> You will need the patch
> [PATCH V3] gpio: palmas: add dt support
>
> which is under review from last few days.
>
Ah, ok. I guess I'm not on the proper ML for that one.
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH V2] ARM: tegra: enable palmas device for dalmore
@ 2013-07-17 8:53 ` Mikko Perttunen
0 siblings, 0 replies; 21+ messages in thread
From: Mikko Perttunen @ 2013-07-17 8:53 UTC (permalink / raw)
To: linux-arm-kernel
On 07/17/2013 11:57 AM, Laxman Dewangan wrote:
> On Tuesday 16 July 2013 07:21 PM, Mikko Perttunen wrote:
>> On 07/10/2013 10:37 AM, Laxman Dewangan wrote:
>>> +
>>> + palmas_gpio: gpio {
>>> + compatible = "ti,palmas-gpio";
>>> + gpio-controller;
>>> + #gpio-cells = <2>;
>>> + };
>> I don't think the palmas-gpio driver ever gets probed since it doesn't
>> have device tree compability strings?
>>
> You will need the patch
> [PATCH V3] gpio: palmas: add dt support
>
> which is under review from last few days.
>
Ah, ok. I guess I'm not on the proper ML for that one.
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH V2] ARM: tegra: enable palmas device for dalmore
2013-07-16 13:51 ` Mikko Perttunen
(?)
@ 2013-07-17 8:57 ` Laxman Dewangan
-1 siblings, 0 replies; 21+ messages in thread
From: Laxman Dewangan @ 2013-07-17 8:57 UTC (permalink / raw)
To: Mikko Perttunen
Cc: swarren-3lzwWm7+Weoh9ZMKESR00Q,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-tegra-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
On Tuesday 16 July 2013 07:21 PM, Mikko Perttunen wrote:
> On 07/10/2013 10:37 AM, Laxman Dewangan wrote:
>> +
>> + palmas_gpio: gpio {
>> + compatible = "ti,palmas-gpio";
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> + };
> I don't think the palmas-gpio driver ever gets probed since it doesn't
> have device tree compability strings?
>
You will need the patch
[PATCH V3] gpio: palmas: add dt support
which is under review from last few days.
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH V2] ARM: tegra: enable palmas device for dalmore
@ 2013-07-17 8:57 ` Laxman Dewangan
0 siblings, 0 replies; 21+ messages in thread
From: Laxman Dewangan @ 2013-07-17 8:57 UTC (permalink / raw)
To: Mikko Perttunen; +Cc: swarren, linux-arm-kernel, linux-tegra, linux-kernel
On Tuesday 16 July 2013 07:21 PM, Mikko Perttunen wrote:
> On 07/10/2013 10:37 AM, Laxman Dewangan wrote:
>> +
>> + palmas_gpio: gpio {
>> + compatible = "ti,palmas-gpio";
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> + };
> I don't think the palmas-gpio driver ever gets probed since it doesn't
> have device tree compability strings?
>
You will need the patch
[PATCH V3] gpio: palmas: add dt support
which is under review from last few days.
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH V2] ARM: tegra: enable palmas device for dalmore
@ 2013-07-17 8:57 ` Laxman Dewangan
0 siblings, 0 replies; 21+ messages in thread
From: Laxman Dewangan @ 2013-07-17 8:57 UTC (permalink / raw)
To: linux-arm-kernel
On Tuesday 16 July 2013 07:21 PM, Mikko Perttunen wrote:
> On 07/10/2013 10:37 AM, Laxman Dewangan wrote:
>> +
>> + palmas_gpio: gpio {
>> + compatible = "ti,palmas-gpio";
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> + };
> I don't think the palmas-gpio driver ever gets probed since it doesn't
> have device tree compability strings?
>
You will need the patch
[PATCH V3] gpio: palmas: add dt support
which is under review from last few days.
^ permalink raw reply [flat|nested] 21+ messages in thread
end of thread, other threads:[~2013-07-17 8:57 UTC | newest]
Thread overview: 21+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-07-10 7:37 [PATCH V2] ARM: tegra: enable palmas device for dalmore Laxman Dewangan
2013-07-10 7:37 ` Laxman Dewangan
2013-07-10 7:37 ` Laxman Dewangan
[not found] ` <1373441852-27176-1-git-send-email-ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2013-07-15 16:48 ` Stephen Warren
2013-07-15 16:48 ` Stephen Warren
2013-07-15 16:48 ` Stephen Warren
[not found] ` <51E427D6.7090702-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org>
2013-07-15 17:28 ` Laxman Dewangan
2013-07-15 17:28 ` Laxman Dewangan
2013-07-15 17:28 ` Laxman Dewangan
[not found] ` <51E43129.7080602-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2013-07-15 17:29 ` Rhyland Klein
2013-07-15 17:29 ` Rhyland Klein
2013-07-15 17:29 ` Rhyland Klein
2013-07-16 13:51 ` Mikko Perttunen
2013-07-16 13:51 ` Mikko Perttunen
2013-07-16 13:51 ` Mikko Perttunen
[not found] ` <51E54FD1.1010404-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2013-07-17 8:57 ` Laxman Dewangan
2013-07-17 8:57 ` Laxman Dewangan
2013-07-17 8:57 ` Laxman Dewangan
[not found] ` <51E65C74.8060405-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2013-07-17 8:53 ` Mikko Perttunen
2013-07-17 8:53 ` Mikko Perttunen
2013-07-17 8:53 ` Mikko Perttunen
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.