Re: [PATCH v3 11/31] net: can: mscan: improve clock API use

[Marc Kleine-Budde <mkl@pengutronix.de>]

[-- Attachment #1.1: Type: text/plain, Size: 3732 bytes --]

On 07/23/2013 01:53 PM, Gerhard Sittig wrote:
> On Mon, Jul 22, 2013 at 14:31 +0200, Marc Kleine-Budde wrote:
>>
>> On 07/22/2013 02:14 PM, Gerhard Sittig wrote:
>>> the .get_clock() callback is run from probe() and might allocate
>>> resources, introduce a .put_clock() callback that is run from remove()
>>> to undo any allocation activities
>>
>> looks good
>>
>>> use devm_get_clk() upon lookup (for SYS and REF) to have the clocks put
>>> upon driver unload
>>
>> fine
>>
>>> assume that resources get prepared but not necessarily enabled in the
>>> setup phase, make the open() and close() callbacks of the CAN network
>>> device enable and disable a previously acquired and prepared clock
>>
>> I think you should call prepare_enable and disable_unprepare in the
>> open/close functions.
> 
> After more local research, which totally eliminated the need to
> pre-enable the CAN related clocks, but might need more discussion
> as it touches the common gate support, I've learned something
> more:
> 
> The CAN clock needs to get enabled during probe() already, since
> registers get accessed between probe() for the driver and open()
> for the network device -- while access to peripheral registers
> crashes the kernel when clocks still are disabled (other hardware
> may just hang or provide fake data, neither of this is OK).

Then call prepare_enable(); before and disable_unprepare(); after
accessing the registers. Have a look at the flexcan driver.

> But I see the point in your suggestion to prepare _and_ enable
> the clock during open() as well -- to have open() cope with
> whatever probe() did, after all the driver is shared among
> platforms, which may differ in what they do during probe().

If you enable a clock to access the registers before open() (and disable
it afterwards), it should not harm any architecture that doesn't need
this clock enabled.

> So I will:
> - make open() of the network device prepare _and_ enable the
>   clock for the peripheral (if acquired during probe())

good

> - adjust open() because ATM it leaves the clock enabled when the
>   network device operation fails (the error path is incomplete in
>   v3)

yes, clock should be disabled if open() fails.

> - make the MPC512x specific probe() time .get_clock() routine not
>   just prepare but enable the clock as well

If needed enable the clock, but disable after probe() has finished.

> - and of course address all the shutdown counter parts of the
>   above setup paths

> This results in:
> - specific chip drivers only need to balance their private get
>   and put clock routines which are called from probe and remove,
>   common paths DTRT for all of them

Yes, but clock should not stay enabled between probe() and open().

[...]

> Removing unnecessary devm_put_clk() calls is orthogonal to that.
> Putting these in isn't totally wrong (they won't harm, and they
> do signal "visual balance" more clearly such that the next person
> won't stop and wonder), but it's true that they are redundant.
> "Trained persons" will wonder as much about their presence as
> untrained persons wonder about their absence. :)  Apparently I'm
> not well trained yet.

The whole point about devm_* is to get rid of auto manually tear down
functions. So please remove all devm_put_clk() calls, as it will be
called automatically if a driver instance is removed.

Marc

-- 
Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |


[-- Attachment #1.2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 259 bytes --]

[-- Attachment #2: Type: text/plain, Size: 150 bytes --]

_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev