From: Keerthy <a0393675@ti.com>
To: Nishanth Menon <nm@ti.com>
Cc: Keerthy <j-keerthy@ti.com>, <bcousson@baylibre.com>,
<linux-omap@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<pawel.moll@arm.com>, <devicetree@vger.kernel.org>,
<rob.herring@calxeda.com>, <linux-arm-kernel@lists.infradead.org>,
<balajitk@ti.com>
Subject: Re: [PATCH] ARM: DTS: DRA7: Add TPS659038 PMIC nodes
Date: Wed, 11 Sep 2013 11:00:10 +0530 [thread overview]
Message-ID: <522FFFE2.2000705@ti.com> (raw)
In-Reply-To: <522E1FB2.10809@ti.com>
On Tuesday 10 September 2013 12:51 AM, Nishanth Menon wrote:
> On 08/26/2013 12:36 AM, Keerthy wrote:
>> The Patch adds nodes for TPS659038 PMIC for DRA7 boards.
>>
>> It is based on top of:
>> http://comments.gmane.org/gmane.linux.ports.arm.omap/102459.
>>
>> Documentation: Documentation/devicetree/bindings/mfd/palmas.txt
>> Documentation/devicetree/bindings/regulator/palmas-pmic.txt
>>
>> Boot Tested on DRA7 d1 Board.
>>
>> Signed-off-by: Keerthy <j-keerthy@ti.com>
>> ---
>> arch/arm/boot/dts/dra7-evm.dts | 118 ++++++++++++++++++++++++++++++++++++++++
>> 1 file changed, 118 insertions(+)
>>
>> Index: linux/arch/arm/boot/dts/dra7-evm.dts
>> ===================================================================
>> --- linux.orig/arch/arm/boot/dts/dra7-evm.dts 2013-08-26 09:57:52.496173554 +0530
>> +++ linux/arch/arm/boot/dts/dra7-evm.dts 2013-08-26 10:38:44.995414695 +0530
>> @@ -93,6 +93,119 @@
>> pinctrl-names = "default";
>> pinctrl-0 = <&i2c1_pins>;
>> clock-frequency = <400000>;
>> +
>> + tps659038: tps659038@58 {
>> + compatible = "ti,tps659038";
>> + reg = <0x58>;
>> +
>> + tps659038_pmic {
>> + compatible = "ti,tps659038-pmic";
>> +
>> + regulators {
>> + smps123_reg: smps123 {
>> + /* VDD_MPU */
>> + regulator-name = "smps123";
>> + regulator-min-microvolt = < 850000>;
>> + regulator-max-microvolt = <1250000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + smps45_reg: smps45 {
>> + /* VDD_DSPEVE */
>> + regulator-name = "smps45";
>> + regulator-min-microvolt = < 850000>;
>> + regulator-max-microvolt = <1150000>;
>> + regulator-boot-on;
>> + };
>> +
>> + smps6_reg: smps6 {
>> + /* VDD_GPU - over VDD_SMPS6 */
>> + regulator-name = "smps6";
>> + regulator-min-microvolt = <850000>;
>> + regulator-max-microvolt = <12500000>;
>> + regulator-boot-on;
>> + };
>> +
>> + smps7_reg: smps7 {
>> + /* CORE_VDD */
>> + regulator-name = "smps7";
>> + regulator-min-microvolt = <850000>;
>> + regulator-max-microvolt = <1030000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + smps8_reg: smps8 {
>> + /* VDD_IVAHD */
>> + regulator-name = "smps8";
>> + regulator-min-microvolt = < 850000>;
>> + regulator-max-microvolt = <1250000>;
>> + regulator-boot-on;
>> + };
>> +
>> + smps9_reg: smps9 {
>> + /* VDDS1V8 */
>> + regulator-name = "smps9";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + ldo1_reg: ldo1 {
>> + /* LDO1_OUT --> SDIO */
>> + regulator-name = "ldo1";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + };
>> +
>> + ldo2_reg: ldo2 {
>> + /* VDD_RTCIO */
>> + /* LDO2 -> VDDSHV5, LDO2 also goes to CAN_PHY_3V3 */
>> + regulator-name = "ldo2";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + };
>> +
>> + ldo3_reg: ldo3 {
>> + /* VDDA_1V8_PHY */
>> + regulator-name = "ldo3";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-boot-on;
>> + };
>> +
>> + ldo9_reg: ldo9 {
>> + /* VDD_RTC */
>> + regulator-name = "ldo9";
>> + regulator-min-microvolt = <1050000>;
>> + regulator-max-microvolt = <1050000>;
>> + regulator-boot-on;
>> + };
>> +
>> + ldoln_reg: ldoln {
>> + /* VDDA_1V8_PLL */
>> + regulator-name = "ldoln";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + ldousb_reg: ldousb {
>> + /* VDDA_3V_USB: VDDA_USBHS33 */
>> + regulator-name = "ldousb";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + };
>> +
>> + };
>> + };
>> + };
>> };
>>
>> &i2c2 {
>>
> Acked-by: Nishanth Menon <nm@ti.com>
>
Thanks Nishanth.
Benoit,
Could you pull this patch?
Regards,
Keerthy
WARNING: multiple messages have this Message-ID (diff)
From: Keerthy <a0393675@ti.com>
To: Nishanth Menon <nm@ti.com>
Cc: devicetree@vger.kernel.org, balajitk@ti.com, pawel.moll@arm.com,
Keerthy <j-keerthy@ti.com>,
linux-kernel@vger.kernel.org, rob.herring@calxeda.com,
bcousson@baylibre.com, linux-omap@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH] ARM: DTS: DRA7: Add TPS659038 PMIC nodes
Date: Wed, 11 Sep 2013 11:00:10 +0530 [thread overview]
Message-ID: <522FFFE2.2000705@ti.com> (raw)
In-Reply-To: <522E1FB2.10809@ti.com>
On Tuesday 10 September 2013 12:51 AM, Nishanth Menon wrote:
> On 08/26/2013 12:36 AM, Keerthy wrote:
>> The Patch adds nodes for TPS659038 PMIC for DRA7 boards.
>>
>> It is based on top of:
>> http://comments.gmane.org/gmane.linux.ports.arm.omap/102459.
>>
>> Documentation: Documentation/devicetree/bindings/mfd/palmas.txt
>> Documentation/devicetree/bindings/regulator/palmas-pmic.txt
>>
>> Boot Tested on DRA7 d1 Board.
>>
>> Signed-off-by: Keerthy <j-keerthy@ti.com>
>> ---
>> arch/arm/boot/dts/dra7-evm.dts | 118 ++++++++++++++++++++++++++++++++++++++++
>> 1 file changed, 118 insertions(+)
>>
>> Index: linux/arch/arm/boot/dts/dra7-evm.dts
>> ===================================================================
>> --- linux.orig/arch/arm/boot/dts/dra7-evm.dts 2013-08-26 09:57:52.496173554 +0530
>> +++ linux/arch/arm/boot/dts/dra7-evm.dts 2013-08-26 10:38:44.995414695 +0530
>> @@ -93,6 +93,119 @@
>> pinctrl-names = "default";
>> pinctrl-0 = <&i2c1_pins>;
>> clock-frequency = <400000>;
>> +
>> + tps659038: tps659038@58 {
>> + compatible = "ti,tps659038";
>> + reg = <0x58>;
>> +
>> + tps659038_pmic {
>> + compatible = "ti,tps659038-pmic";
>> +
>> + regulators {
>> + smps123_reg: smps123 {
>> + /* VDD_MPU */
>> + regulator-name = "smps123";
>> + regulator-min-microvolt = < 850000>;
>> + regulator-max-microvolt = <1250000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + smps45_reg: smps45 {
>> + /* VDD_DSPEVE */
>> + regulator-name = "smps45";
>> + regulator-min-microvolt = < 850000>;
>> + regulator-max-microvolt = <1150000>;
>> + regulator-boot-on;
>> + };
>> +
>> + smps6_reg: smps6 {
>> + /* VDD_GPU - over VDD_SMPS6 */
>> + regulator-name = "smps6";
>> + regulator-min-microvolt = <850000>;
>> + regulator-max-microvolt = <12500000>;
>> + regulator-boot-on;
>> + };
>> +
>> + smps7_reg: smps7 {
>> + /* CORE_VDD */
>> + regulator-name = "smps7";
>> + regulator-min-microvolt = <850000>;
>> + regulator-max-microvolt = <1030000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + smps8_reg: smps8 {
>> + /* VDD_IVAHD */
>> + regulator-name = "smps8";
>> + regulator-min-microvolt = < 850000>;
>> + regulator-max-microvolt = <1250000>;
>> + regulator-boot-on;
>> + };
>> +
>> + smps9_reg: smps9 {
>> + /* VDDS1V8 */
>> + regulator-name = "smps9";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + ldo1_reg: ldo1 {
>> + /* LDO1_OUT --> SDIO */
>> + regulator-name = "ldo1";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + };
>> +
>> + ldo2_reg: ldo2 {
>> + /* VDD_RTCIO */
>> + /* LDO2 -> VDDSHV5, LDO2 also goes to CAN_PHY_3V3 */
>> + regulator-name = "ldo2";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + };
>> +
>> + ldo3_reg: ldo3 {
>> + /* VDDA_1V8_PHY */
>> + regulator-name = "ldo3";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-boot-on;
>> + };
>> +
>> + ldo9_reg: ldo9 {
>> + /* VDD_RTC */
>> + regulator-name = "ldo9";
>> + regulator-min-microvolt = <1050000>;
>> + regulator-max-microvolt = <1050000>;
>> + regulator-boot-on;
>> + };
>> +
>> + ldoln_reg: ldoln {
>> + /* VDDA_1V8_PLL */
>> + regulator-name = "ldoln";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + ldousb_reg: ldousb {
>> + /* VDDA_3V_USB: VDDA_USBHS33 */
>> + regulator-name = "ldousb";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + };
>> +
>> + };
>> + };
>> + };
>> };
>>
>> &i2c2 {
>>
> Acked-by: Nishanth Menon <nm@ti.com>
>
Thanks Nishanth.
Benoit,
Could you pull this patch?
Regards,
Keerthy
WARNING: multiple messages have this Message-ID (diff)
From: a0393675@ti.com (Keerthy)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] ARM: DTS: DRA7: Add TPS659038 PMIC nodes
Date: Wed, 11 Sep 2013 11:00:10 +0530 [thread overview]
Message-ID: <522FFFE2.2000705@ti.com> (raw)
In-Reply-To: <522E1FB2.10809@ti.com>
On Tuesday 10 September 2013 12:51 AM, Nishanth Menon wrote:
> On 08/26/2013 12:36 AM, Keerthy wrote:
>> The Patch adds nodes for TPS659038 PMIC for DRA7 boards.
>>
>> It is based on top of:
>> http://comments.gmane.org/gmane.linux.ports.arm.omap/102459.
>>
>> Documentation: Documentation/devicetree/bindings/mfd/palmas.txt
>> Documentation/devicetree/bindings/regulator/palmas-pmic.txt
>>
>> Boot Tested on DRA7 d1 Board.
>>
>> Signed-off-by: Keerthy <j-keerthy@ti.com>
>> ---
>> arch/arm/boot/dts/dra7-evm.dts | 118 ++++++++++++++++++++++++++++++++++++++++
>> 1 file changed, 118 insertions(+)
>>
>> Index: linux/arch/arm/boot/dts/dra7-evm.dts
>> ===================================================================
>> --- linux.orig/arch/arm/boot/dts/dra7-evm.dts 2013-08-26 09:57:52.496173554 +0530
>> +++ linux/arch/arm/boot/dts/dra7-evm.dts 2013-08-26 10:38:44.995414695 +0530
>> @@ -93,6 +93,119 @@
>> pinctrl-names = "default";
>> pinctrl-0 = <&i2c1_pins>;
>> clock-frequency = <400000>;
>> +
>> + tps659038: tps659038 at 58 {
>> + compatible = "ti,tps659038";
>> + reg = <0x58>;
>> +
>> + tps659038_pmic {
>> + compatible = "ti,tps659038-pmic";
>> +
>> + regulators {
>> + smps123_reg: smps123 {
>> + /* VDD_MPU */
>> + regulator-name = "smps123";
>> + regulator-min-microvolt = < 850000>;
>> + regulator-max-microvolt = <1250000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + smps45_reg: smps45 {
>> + /* VDD_DSPEVE */
>> + regulator-name = "smps45";
>> + regulator-min-microvolt = < 850000>;
>> + regulator-max-microvolt = <1150000>;
>> + regulator-boot-on;
>> + };
>> +
>> + smps6_reg: smps6 {
>> + /* VDD_GPU - over VDD_SMPS6 */
>> + regulator-name = "smps6";
>> + regulator-min-microvolt = <850000>;
>> + regulator-max-microvolt = <12500000>;
>> + regulator-boot-on;
>> + };
>> +
>> + smps7_reg: smps7 {
>> + /* CORE_VDD */
>> + regulator-name = "smps7";
>> + regulator-min-microvolt = <850000>;
>> + regulator-max-microvolt = <1030000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + smps8_reg: smps8 {
>> + /* VDD_IVAHD */
>> + regulator-name = "smps8";
>> + regulator-min-microvolt = < 850000>;
>> + regulator-max-microvolt = <1250000>;
>> + regulator-boot-on;
>> + };
>> +
>> + smps9_reg: smps9 {
>> + /* VDDS1V8 */
>> + regulator-name = "smps9";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + ldo1_reg: ldo1 {
>> + /* LDO1_OUT --> SDIO */
>> + regulator-name = "ldo1";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + };
>> +
>> + ldo2_reg: ldo2 {
>> + /* VDD_RTCIO */
>> + /* LDO2 -> VDDSHV5, LDO2 also goes to CAN_PHY_3V3 */
>> + regulator-name = "ldo2";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + };
>> +
>> + ldo3_reg: ldo3 {
>> + /* VDDA_1V8_PHY */
>> + regulator-name = "ldo3";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-boot-on;
>> + };
>> +
>> + ldo9_reg: ldo9 {
>> + /* VDD_RTC */
>> + regulator-name = "ldo9";
>> + regulator-min-microvolt = <1050000>;
>> + regulator-max-microvolt = <1050000>;
>> + regulator-boot-on;
>> + };
>> +
>> + ldoln_reg: ldoln {
>> + /* VDDA_1V8_PLL */
>> + regulator-name = "ldoln";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + ldousb_reg: ldousb {
>> + /* VDDA_3V_USB: VDDA_USBHS33 */
>> + regulator-name = "ldousb";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + };
>> +
>> + };
>> + };
>> + };
>> };
>>
>> &i2c2 {
>>
> Acked-by: Nishanth Menon <nm@ti.com>
>
Thanks Nishanth.
Benoit,
Could you pull this patch?
Regards,
Keerthy
next prev parent reply other threads:[~2013-09-11 5:30 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-08-26 5:36 [PATCH] ARM: DTS: DRA7: Add TPS659038 PMIC nodes Keerthy
2013-08-26 5:36 ` Keerthy
2013-08-26 5:36 ` Keerthy
2013-09-03 6:33 ` Keerthy
2013-09-03 6:33 ` Keerthy
2013-09-03 6:33 ` Keerthy
2013-09-09 19:21 ` Nishanth Menon
2013-09-09 19:21 ` Nishanth Menon
2013-09-09 19:21 ` Nishanth Menon
2013-09-11 5:30 ` Keerthy [this message]
2013-09-11 5:30 ` Keerthy
2013-09-11 5:30 ` Keerthy
2013-10-03 13:39 ` Benoit Cousson
2013-10-03 13:39 ` Benoit Cousson
2013-10-04 8:25 ` Keerthy
2013-10-04 8:25 ` Keerthy
2013-10-04 8:25 ` Keerthy
-- strict thread matches above, loose matches on Subject: below --
2013-08-13 5:42 Keerthy
2013-08-13 5:42 ` Keerthy
2013-08-14 23:35 ` Nishanth Menon
2013-08-14 23:35 ` Nishanth Menon
2013-08-16 8:46 ` Balaji T K
2013-08-16 9:01 ` Keerthy
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=522FFFE2.2000705@ti.com \
--to=a0393675@ti.com \
--cc=balajitk@ti.com \
--cc=bcousson@baylibre.com \
--cc=devicetree@vger.kernel.org \
--cc=j-keerthy@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=nm@ti.com \
--cc=pawel.moll@arm.com \
--cc=rob.herring@calxeda.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.