* [U-Boot] [PATCH 0/6] adapt s3c24x0 driver to new i2c framework
@ 2013-11-13 14:31 Piotr Wilczek
2013-11-13 14:31 ` [U-Boot] [PATCH 1/6] driver:i2c:s3c24x0: adapt driver to new i2c Piotr Wilczek
` (6 more replies)
0 siblings, 7 replies; 17+ messages in thread
From: Piotr Wilczek @ 2013-11-13 14:31 UTC (permalink / raw)
To: u-boot
This patch series adapts the s3c24x0 driver to the new i2c framework.
Config file is modified for all the boards that use the driver.
Boards VCMA9, arndale and exynos5250 are compile tested only.
Boards Trats and Trats2 were hardware tested.
All boards compile clean.
Piotr Wilczek (6):
driver:i2c:s3c24x0: adapt driver to new i2c
board:arndale: switch to new i2c framework
board:VCMA9 switch to new i2c framework
board:smdk5250: switch to new i2c framework
board:trats: switch to new i2c framework
board:trats2: switch Trats2 to new i2c framework
board/samsung/smdk5250/exynos5-dt.c | 2 -
board/samsung/trats/trats.c | 21 +++--
board/samsung/trats2/trats2.c | 35 ++++++--
drivers/i2c/Makefile | 2 +-
drivers/i2c/s3c24x0_i2c.c | 157 ++++++++++++++++++++++-------------
include/configs/VCMA9.h | 8 +-
include/configs/arndale.h | 9 +-
include/configs/exynos5250-dt.h | 8 +-
include/configs/trats.h | 25 ++----
include/configs/trats2.h | 29 +++----
10 files changed, 174 insertions(+), 122 deletions(-)
--
1.7.9.5
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH 1/6] driver:i2c:s3c24x0: adapt driver to new i2c
2013-11-13 14:31 [U-Boot] [PATCH 0/6] adapt s3c24x0 driver to new i2c framework Piotr Wilczek
@ 2013-11-13 14:31 ` Piotr Wilczek
2013-11-18 6:17 ` Heiko Schocher
2013-11-13 14:31 ` [U-Boot] [PATCH 2/6] board:arndale: switch to new i2c framework Piotr Wilczek
` (5 subsequent siblings)
6 siblings, 1 reply; 17+ messages in thread
From: Piotr Wilczek @ 2013-11-13 14:31 UTC (permalink / raw)
To: u-boot
The s3c24x0 i2c driver is adapted to new i2c framework.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
---
drivers/i2c/Makefile | 2 +-
drivers/i2c/s3c24x0_i2c.c | 157 +++++++++++++++++++++++++++++----------------
2 files changed, 101 insertions(+), 58 deletions(-)
diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
index 553b519..fa3a875 100644
--- a/drivers/i2c/Makefile
+++ b/drivers/i2c/Makefile
@@ -12,7 +12,6 @@ obj-$(CONFIG_I2C_MVTWSI) += mvtwsi.o
obj-$(CONFIG_I2C_MV) += mv_i2c.o
obj-$(CONFIG_I2C_MXS) += mxs_i2c.o
obj-$(CONFIG_PCA9564_I2C) += pca9564_i2c.o
-obj-$(CONFIG_DRIVER_S3C24X0_I2C) += s3c24x0_i2c.o
obj-$(CONFIG_TSI108_I2C) += tsi108_i2c.o
obj-$(CONFIG_U8500_I2C) += u8500_i2c.o
obj-$(CONFIG_SH_SH7734_I2C) += sh_sh7734_i2c.o
@@ -24,6 +23,7 @@ obj-$(CONFIG_SYS_I2C_OMAP24XX) += omap24xx_i2c.o
obj-$(CONFIG_SYS_I2C_OMAP34XX) += omap24xx_i2c.o
obj-$(CONFIG_SYS_I2C_PPC4XX) += ppc4xx_i2c.o
obj-$(CONFIG_SYS_I2C_RCAR) += rcar_i2c.o
+obj-$(CONFIG_SYS_I2C_S3C24X0) += s3c24x0_i2c.o
obj-$(CONFIG_SYS_I2C_SH) += sh_i2c.o
obj-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o
obj-$(CONFIG_SYS_I2C_TEGRA) += tegra_i2c.o
diff --git a/drivers/i2c/s3c24x0_i2c.c b/drivers/i2c/s3c24x0_i2c.c
index f77a9d1..0051cac 100644
--- a/drivers/i2c/s3c24x0_i2c.c
+++ b/drivers/i2c/s3c24x0_i2c.c
@@ -23,8 +23,6 @@
#include <i2c.h>
#include "s3c24x0_i2c.h"
-#ifdef CONFIG_HARD_I2C
-
#define I2C_WRITE 0
#define I2C_READ 1
@@ -127,7 +125,6 @@
* For SPL boot some boards need i2c before SDRAM is initialised so force
* variables to live in SRAM
*/
-static unsigned int g_current_bus __attribute__((section(".data")));
static struct s3c24x0_i2c_bus i2c_bus[CONFIG_MAX_I2C_NUM]
__attribute__((section(".data")));
@@ -143,6 +140,7 @@ static struct s3c24x0_i2c_bus *get_bus(unsigned int bus_idx)
struct s3c24x0_i2c_bus *bus;
bus = &i2c_bus[bus_idx];
+
if (bus->active)
return bus;
}
@@ -254,17 +252,17 @@ static void ReadWriteByte(struct s3c24x0_i2c *i2c)
writel(readl(&i2c->iiccon) & ~I2CCON_IRPND, &i2c->iiccon);
}
-static struct s3c24x0_i2c *get_base_i2c(void)
+static struct s3c24x0_i2c *get_base_i2c(int bus)
{
#ifdef CONFIG_EXYNOS4
struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c *)(samsung_get_base_i2c()
+ (EXYNOS4_I2C_SPACING
- * g_current_bus));
+ * bus));
return i2c;
#elif defined CONFIG_EXYNOS5
struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c *)(samsung_get_base_i2c()
+ (EXYNOS5_I2C_SPACING
- * g_current_bus));
+ * bus));
return i2c;
#else
return s3c24x0_get_base_i2c();
@@ -298,7 +296,6 @@ static void i2c_ch_init(struct s3c24x0_i2c *i2c, int speed, int slaveadd)
writel(I2C_MODE_MT | I2C_TXRX_ENA, &i2c->iicstat);
}
-#ifdef CONFIG_I2C_MULTI_BUS
static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
{
struct exynos5_hsi2c *hsregs = i2c_bus->hsregs;
@@ -307,8 +304,10 @@ static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
unsigned int i = 0, utemp0 = 0, utemp1 = 0;
unsigned int t_ftl_cycle;
-#if defined CONFIG_EXYNOS5
+#if (defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5)
clkin = get_i2c_clk();
+#else
+ clkin = get_PCLK();
#endif
/* FPCLK / FI2C =
* (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + 2 * FLT_CYCLE
@@ -330,7 +329,6 @@ static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
}
return -1;
}
-#endif
static void hsi2c_ch_init(struct s3c24x0_i2c_bus *i2c_bus)
{
@@ -401,49 +399,18 @@ static void exynos5_i2c_reset(struct s3c24x0_i2c_bus *i2c_bus)
hsi2c_ch_init(i2c_bus);
}
-/*
- * MULTI BUS I2C support
- */
-
-#ifdef CONFIG_I2C_MULTI_BUS
-int i2c_set_bus_num(unsigned int bus)
-{
- struct s3c24x0_i2c_bus *i2c_bus;
-
- i2c_bus = get_bus(bus);
- if (!i2c_bus)
- return -1;
- g_current_bus = bus;
-
- if (i2c_bus->is_highspeed) {
- if (hsi2c_get_clk_details(i2c_bus))
- return -1;
- hsi2c_ch_init(i2c_bus);
- } else {
- i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency,
- CONFIG_SYS_I2C_SLAVE);
- }
-
- return 0;
-}
-
-unsigned int i2c_get_bus_num(void)
-{
- return g_current_bus;
-}
-#endif
-
-void i2c_init(int speed, int slaveadd)
+static void s3c24x0_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd)
{
struct s3c24x0_i2c *i2c;
+ struct s3c24x0_i2c_bus *bus;
+
#if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5)
struct s3c24x0_gpio *gpio = s3c24x0_get_base_gpio();
#endif
ulong start_time = get_timer(0);
/* By default i2c channel 0 is the current bus */
- g_current_bus = 0;
- i2c = get_base_i2c();
+ i2c = get_base_i2c(adap->hwadapnr);
/*
* In case the previous transfer is still going, wait to give it a
@@ -505,6 +472,10 @@ void i2c_init(int speed, int slaveadd)
}
#endif /* #if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5) */
i2c_ch_init(i2c, speed, slaveadd);
+
+ bus = &i2c_bus[adap->hwadapnr];
+ bus->active = true;
+ bus->regs = i2c;
}
/*
@@ -728,6 +699,29 @@ static int hsi2c_read(struct exynos5_hsi2c *i2c,
return rv;
}
+static unsigned int s3c24x0_i2c_set_bus_speed(struct i2c_adapter *adap,
+ unsigned int speed)
+{
+ struct s3c24x0_i2c_bus *i2c_bus;
+
+ i2c_bus = get_bus(adap->hwadapnr);
+ if (!i2c_bus)
+ return -1;
+
+ i2c_bus->clock_frequency = speed;
+
+ if (i2c_bus->is_highspeed) {
+ if (hsi2c_get_clk_details(i2c_bus))
+ return -1;
+ hsi2c_ch_init(i2c_bus);
+ } else {
+ i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE);
+ }
+
+ return 0;
+}
+
/*
* cmd_type is 0 for write, 1 for read.
*
@@ -840,13 +834,13 @@ bailout:
return result;
}
-int i2c_probe(uchar chip)
+static int s3c24x0_i2c_probe(struct i2c_adapter *adap, uchar chip)
{
struct s3c24x0_i2c_bus *i2c_bus;
uchar buf[1];
int ret;
- i2c_bus = get_bus(g_current_bus);
+ i2c_bus = get_bus(adap->hwadapnr);
if (!i2c_bus)
return -1;
buf[0] = 0;
@@ -864,11 +858,11 @@ int i2c_probe(uchar chip)
I2C_READ, chip << 1, 0, 0, buf, 1);
}
-
return ret != I2C_OK;
}
-int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
+static int s3c24x0_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
+ int alen, uchar *buffer, int len)
{
struct s3c24x0_i2c_bus *i2c_bus;
uchar xaddr[4];
@@ -902,7 +896,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
chip |= ((addr >> (alen * 8)) &
CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
#endif
- i2c_bus = get_bus(g_current_bus);
+ i2c_bus = get_bus(adap->hwadapnr);
if (!i2c_bus)
return -1;
@@ -922,7 +916,8 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
return 0;
}
-int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
+static int s3c24x0_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
+ int alen, uchar *buffer, int len)
{
struct s3c24x0_i2c_bus *i2c_bus;
uchar xaddr[4];
@@ -955,7 +950,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
chip |= ((addr >> (alen * 8)) &
CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
#endif
- i2c_bus = get_bus(g_current_bus);
+ i2c_bus = get_bus(adap->hwadapnr);
if (!i2c_bus)
return -1;
@@ -1001,8 +996,8 @@ static void process_nodes(const void *blob, int node_list[], int count,
bus->id = pinmux_decode_periph_id(blob, node);
bus->clock_frequency = fdtdec_get_int(blob, node,
- "clock-frequency",
- CONFIG_SYS_I2C_SPEED);
+ "clock-frequency",
+ CONFIG_SYS_I2C_S3C24X0_SPEED);
bus->node = node;
bus->bus_num = i;
exynos_pinmux_config(bus->id, 0);
@@ -1044,7 +1039,6 @@ int i2c_get_bus_num_fdt(int node)
return -1;
}
-#ifdef CONFIG_I2C_MULTI_BUS
int i2c_reset_port_fdt(const void *blob, int node)
{
struct s3c24x0_i2c_bus *i2c_bus;
@@ -1068,12 +1062,61 @@ int i2c_reset_port_fdt(const void *blob, int node)
hsi2c_ch_init(i2c_bus);
} else {
i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency,
- CONFIG_SYS_I2C_SLAVE);
+ CONFIG_SYS_I2C_S3C24X0_SLAVE);
}
return 0;
}
#endif
-#endif
-#endif /* CONFIG_HARD_I2C */
+/*
+ * Register s3c24x0 i2c adapters
+ */
+U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_0, s3c24x0_i2c_init, s3c24x0_i2c_probe,
+ s3c24x0_i2c_read, s3c24x0_i2c_write,
+ s3c24x0_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_S3C24X0_SPEED,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE,
+ 0)
+U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_1, s3c24x0_i2c_init, s3c24x0_i2c_probe,
+ s3c24x0_i2c_read, s3c24x0_i2c_write,
+ s3c24x0_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_S3C24X0_SPEED,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE,
+ 1)
+U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_2, s3c24x0_i2c_init, s3c24x0_i2c_probe,
+ s3c24x0_i2c_read, s3c24x0_i2c_write,
+ s3c24x0_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_S3C24X0_SPEED,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE,
+ 2)
+U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_3, s3c24x0_i2c_init, s3c24x0_i2c_probe,
+ s3c24x0_i2c_read, s3c24x0_i2c_write,
+ s3c24x0_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_S3C24X0_SPEED,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE,
+ 3)
+U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_4, s3c24x0_i2c_init, s3c24x0_i2c_probe,
+ s3c24x0_i2c_read, s3c24x0_i2c_write,
+ s3c24x0_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_S3C24X0_SPEED,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE,
+ 4)
+U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_5, s3c24x0_i2c_init, s3c24x0_i2c_probe,
+ s3c24x0_i2c_read, s3c24x0_i2c_write,
+ s3c24x0_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_S3C24X0_SPEED,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE,
+ 5)
+U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_6, s3c24x0_i2c_init, s3c24x0_i2c_probe,
+ s3c24x0_i2c_read, s3c24x0_i2c_write,
+ s3c24x0_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_S3C24X0_SPEED,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE,
+ 6)
+U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_7, s3c24x0_i2c_init, s3c24x0_i2c_probe,
+ s3c24x0_i2c_read, s3c24x0_i2c_write,
+ s3c24x0_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_S3C24X0_SPEED,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE,
+ 7)
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH 2/6] board:arndale: switch to new i2c framework
2013-11-13 14:31 [U-Boot] [PATCH 0/6] adapt s3c24x0 driver to new i2c framework Piotr Wilczek
2013-11-13 14:31 ` [U-Boot] [PATCH 1/6] driver:i2c:s3c24x0: adapt driver to new i2c Piotr Wilczek
@ 2013-11-13 14:31 ` Piotr Wilczek
2013-11-13 14:31 ` [U-Boot] [PATCH 3/6] board:VCMA9 " Piotr Wilczek
` (4 subsequent siblings)
6 siblings, 0 replies; 17+ messages in thread
From: Piotr Wilczek @ 2013-11-13 14:31 UTC (permalink / raw)
To: u-boot
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Inderpal Singh <inderpal.singh@linaro.org>
---
include/configs/arndale.h | 9 ++++-----
1 file changed, 4 insertions(+), 5 deletions(-)
diff --git a/include/configs/arndale.h b/include/configs/arndale.h
index 45fa047..ea8753b 100644
--- a/include/configs/arndale.h
+++ b/include/configs/arndale.h
@@ -214,13 +214,12 @@
/* I2C */
#define CONFIG_SYS_I2C_INIT_BOARD
-#define CONFIG_HARD_I2C
+#define CONFIG_SYS_I2C
#define CONFIG_CMD_I2C
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 Kbps */
-#define CONFIG_DRIVER_S3C24X0_I2C
-#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* 100 Kbps */
+#define CONFIG_SYS_I2C_S3C24X0
#define CONFIG_MAX_I2C_NUM 8
-#define CONFIG_SYS_I2C_SLAVE 0x0
+#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x0
#define CONFIG_I2C_EDID
/* PMIC */
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH 3/6] board:VCMA9 switch to new i2c framework
2013-11-13 14:31 [U-Boot] [PATCH 0/6] adapt s3c24x0 driver to new i2c framework Piotr Wilczek
2013-11-13 14:31 ` [U-Boot] [PATCH 1/6] driver:i2c:s3c24x0: adapt driver to new i2c Piotr Wilczek
2013-11-13 14:31 ` [U-Boot] [PATCH 2/6] board:arndale: switch to new i2c framework Piotr Wilczek
@ 2013-11-13 14:31 ` Piotr Wilczek
2013-11-13 14:31 ` [U-Boot] [PATCH 4/6] board:smdk5250: " Piotr Wilczek
` (3 subsequent siblings)
6 siblings, 0 replies; 17+ messages in thread
From: Piotr Wilczek @ 2013-11-13 14:31 UTC (permalink / raw)
To: u-boot
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: David M?ller <d.mueller@elsoft.ch>
---
include/configs/VCMA9.h | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/include/configs/VCMA9.h b/include/configs/VCMA9.h
index 79a6079..57b620d 100644
--- a/include/configs/VCMA9.h
+++ b/include/configs/VCMA9.h
@@ -73,12 +73,12 @@
* the MPL VCMA9 is equipped with an ATMEL 24C256 EEPROM at
* address 0x50 with 16bit addressing
*/
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */
-#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave addr */
+#define CONFIG_SYS_I2C
/* we use the built-in I2C controller */
-#define CONFIG_DRIVER_S3C24X0_I2C
+#define CONFIG_SYS_I2C_S3C24X0
+#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* I2C speed */
+#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x7F /* I2C slave addr */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH 4/6] board:smdk5250: switch to new i2c framework
2013-11-13 14:31 [U-Boot] [PATCH 0/6] adapt s3c24x0 driver to new i2c framework Piotr Wilczek
` (2 preceding siblings ...)
2013-11-13 14:31 ` [U-Boot] [PATCH 3/6] board:VCMA9 " Piotr Wilczek
@ 2013-11-13 14:31 ` Piotr Wilczek
2013-11-13 14:31 ` [U-Boot] [PATCH 5/6] board:trats: " Piotr Wilczek
` (2 subsequent siblings)
6 siblings, 0 replies; 17+ messages in thread
From: Piotr Wilczek @ 2013-11-13 14:31 UTC (permalink / raw)
To: u-boot
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Chander Kashyap <k.chander@samsung.com>
---
board/samsung/smdk5250/exynos5-dt.c | 2 --
include/configs/exynos5250-dt.h | 8 ++++----
2 files changed, 4 insertions(+), 6 deletions(-)
diff --git a/board/samsung/smdk5250/exynos5-dt.c b/board/samsung/smdk5250/exynos5-dt.c
index 6bcc883..6aa0509 100644
--- a/board/samsung/smdk5250/exynos5-dt.c
+++ b/board/samsung/smdk5250/exynos5-dt.c
@@ -150,8 +150,6 @@ int power_init_board(void)
set_ps_hold_ctrl();
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-
if (pmic_init(I2C_PMIC))
return -1;
diff --git a/include/configs/exynos5250-dt.h b/include/configs/exynos5250-dt.h
index bdefee1..0155322 100644
--- a/include/configs/exynos5250-dt.h
+++ b/include/configs/exynos5250-dt.h
@@ -249,13 +249,13 @@
/* I2C */
#define CONFIG_SYS_I2C_INIT_BOARD
-#define CONFIG_HARD_I2C
+#define CONFIG_SYS_I2C
#define CONFIG_CMD_I2C
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 Kbps */
-#define CONFIG_DRIVER_S3C24X0_I2C
+#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* 100 Kbps */
+#define CONFIG_SYS_I2C_S3C24X0
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_MAX_I2C_NUM 8
-#define CONFIG_SYS_I2C_SLAVE 0x0
+#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x0
#define CONFIG_I2C_EDID
/* PMIC */
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH 5/6] board:trats: switch to new i2c framework
2013-11-13 14:31 [U-Boot] [PATCH 0/6] adapt s3c24x0 driver to new i2c framework Piotr Wilczek
` (3 preceding siblings ...)
2013-11-13 14:31 ` [U-Boot] [PATCH 4/6] board:smdk5250: " Piotr Wilczek
@ 2013-11-13 14:31 ` Piotr Wilczek
2013-11-13 14:31 ` [U-Boot] [PATCH 6/6] board:trats2: switch Trats2 " Piotr Wilczek
2013-11-20 9:43 ` [U-Boot] [PATCH V2 1/2] driver:i2c:s3c24x0: adapt driver to new i2c Piotr Wilczek
6 siblings, 0 replies; 17+ messages in thread
From: Piotr Wilczek @ 2013-11-13 14:31 UTC (permalink / raw)
To: u-boot
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
---
board/samsung/trats/trats.c | 21 ++++++++++++---------
include/configs/trats.h | 25 ++++++++-----------------
2 files changed, 20 insertions(+), 26 deletions(-)
diff --git a/board/samsung/trats/trats.c b/board/samsung/trats/trats.c
index 7012c13..44be5fc 100644
--- a/board/samsung/trats/trats.c
+++ b/board/samsung/trats/trats.c
@@ -57,15 +57,18 @@ int board_init(void)
void i2c_init_board(void)
{
- struct exynos4_gpio_part1 *gpio1 =
- (struct exynos4_gpio_part1 *)samsung_get_base_gpio_part1();
+ int err;
struct exynos4_gpio_part2 *gpio2 =
(struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2();
- /* I2C_5 -> PMIC -> Adapter 0 */
- s5p_gpio_direction_output(&gpio1->b, 7, 1);
- s5p_gpio_direction_output(&gpio1->b, 6, 1);
- /* I2C_9 -> FG -> Adapter 1 */
+ /* I2C_5 -> PMIC */
+ err = exynos_pinmux_config(PERIPH_ID_I2C5, PINMUX_FLAG_NONE);
+ if (err) {
+ debug("I2C%d not configured\n", (I2C_5));
+ return;
+ }
+
+ /* I2C_8 -> FG */
s5p_gpio_direction_output(&gpio2->y4, 0, 1);
s5p_gpio_direction_output(&gpio2->y4, 1, 1);
}
@@ -290,10 +293,10 @@ int power_init_board(void)
* The FUEL_GAUGE is marked as I2C9 on the schematic, but connected
* to logical I2C adapter 1
*/
- ret = pmic_init(I2C_0);
+ ret = pmic_init(I2C_5);
ret |= pmic_init_max8997();
- ret |= power_fg_init(I2C_1);
- ret |= power_muic_init(I2C_0);
+ ret |= power_fg_init(I2C_8);
+ ret |= power_muic_init(I2C_5);
ret |= power_bat_init(0);
if (ret)
return ret;
diff --git a/include/configs/trats.h b/include/configs/trats.h
index 3d080c4..f163303 100644
--- a/include/configs/trats.h
+++ b/include/configs/trats.h
@@ -16,6 +16,7 @@
*/
#define CONFIG_SAMSUNG /* in a SAMSUNG core */
#define CONFIG_S5P /* which is in a S5P Family */
+#define CONFIG_EXYNOS4 /* which is in a EXYNOS4XXX */
#define CONFIG_EXYNOS4210 /* which is in a EXYNOS4210 */
#define CONFIG_TRATS /* working with TRATS */
#define CONFIG_TIZEN /* TIZEN lib */
@@ -268,31 +269,21 @@
#define CONFIG_SYS_CACHELINE_SIZE 32
#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_S3C24X0
+#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000
+#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0xFE
+#define CONFIG_MAX_I2C_NUM 8
#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
#define CONFIG_SYS_I2C_SOFT_SPEED 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
-#define I2C_SOFT_DECLARATIONS2
-#define CONFIG_SYS_I2C_SOFT_SPEED_2 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F
+#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F
#define CONFIG_SOFT_I2C_READ_REPEATED_START
#define CONFIG_SYS_I2C_INIT_BOARD
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SOFT_I2C_MULTI_BUS
-#define CONFIG_SYS_MAX_I2C_BUS 15
#include <asm/arch/gpio.h>
-/* I2C PMIC */
-#define CONFIG_SOFT_I2C_I2C5_SCL exynos4_gpio_part1_get_nr(b, 7)
-#define CONFIG_SOFT_I2C_I2C5_SDA exynos4_gpio_part1_get_nr(b, 6)
-
/* I2C FG */
-#define CONFIG_SOFT_I2C_I2C9_SCL exynos4_gpio_part2_get_nr(y4, 1)
-#define CONFIG_SOFT_I2C_I2C9_SDA exynos4_gpio_part2_get_nr(y4, 0)
-
-#define CONFIG_SOFT_I2C_GPIO_SCL get_multi_scl_pin()
-#define CONFIG_SOFT_I2C_GPIO_SDA get_multi_sda_pin()
-#define I2C_INIT multi_i2c_init()
+#define CONFIG_SOFT_I2C_GPIO_SCL exynos4_gpio_part2_get_nr(y4, 1)
+#define CONFIG_SOFT_I2C_GPIO_SDA exynos4_gpio_part2_get_nr(y4, 0)
#define CONFIG_POWER
#define CONFIG_POWER_I2C
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH 6/6] board:trats2: switch Trats2 to new i2c framework
2013-11-13 14:31 [U-Boot] [PATCH 0/6] adapt s3c24x0 driver to new i2c framework Piotr Wilczek
` (4 preceding siblings ...)
2013-11-13 14:31 ` [U-Boot] [PATCH 5/6] board:trats: " Piotr Wilczek
@ 2013-11-13 14:31 ` Piotr Wilczek
2013-11-20 9:43 ` [U-Boot] [PATCH V2 1/2] driver:i2c:s3c24x0: adapt driver to new i2c Piotr Wilczek
6 siblings, 0 replies; 17+ messages in thread
From: Piotr Wilczek @ 2013-11-13 14:31 UTC (permalink / raw)
To: u-boot
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
---
board/samsung/trats2/trats2.c | 35 +++++++++++++++++++++++++++++------
include/configs/trats2.h | 29 ++++++++++++-----------------
2 files changed, 41 insertions(+), 23 deletions(-)
diff --git a/board/samsung/trats2/trats2.c b/board/samsung/trats2/trats2.c
index d44d825..8df85ee 100644
--- a/board/samsung/trats2/trats2.c
+++ b/board/samsung/trats2/trats2.c
@@ -115,12 +115,17 @@ static void board_external_gpio_init(void)
#ifdef CONFIG_SYS_I2C_INIT_BOARD
static void board_init_i2c(void)
{
+ int err;
+
gpio1 = (struct exynos4x12_gpio_part1 *)EXYNOS4X12_GPIO_PART1_BASE;
gpio2 = (struct exynos4x12_gpio_part2 *)EXYNOS4X12_GPIO_PART2_BASE;
/* I2C_7 */
- s5p_gpio_direction_output(&gpio1->d0, 2, 1);
- s5p_gpio_direction_output(&gpio1->d0, 3, 1);
+ err = exynos_pinmux_config(PERIPH_ID_I2C7, PINMUX_FLAG_NONE);
+ if (err) {
+ debug("I2C%d not configured\n", (I2C_7));
+ return;
+ }
/* I2C_8 */
s5p_gpio_direction_output(&gpio1->f1, 4, 1);
@@ -132,6 +137,24 @@ static void board_init_i2c(void)
}
#endif
+#ifdef CONFIG_SYS_I2C_SOFT
+int get_soft_i2c_scl_pin(void)
+{
+ if (I2C_ADAP_HWNR)
+ return exynos4x12_gpio_part2_get_nr(m2, 1); /* I2C9 */
+ else
+ return exynos4x12_gpio_part1_get_nr(f1, 4); /* I2C8 */
+}
+
+int get_soft_i2c_sda_pin(void)
+{
+ if (I2C_ADAP_HWNR)
+ return exynos4x12_gpio_part2_get_nr(m2, 0); /* I2C9 */
+ else
+ return exynos4x12_gpio_part1_get_nr(f1, 5); /* I2C8 */
+}
+#endif
+
int board_early_init_f(void)
{
check_hw_revision();
@@ -167,11 +190,11 @@ int power_init_board(void)
#ifdef CONFIG_SYS_I2C_INIT_BOARD
board_init_i2c();
#endif
- pmic_init(I2C_0); /* I2C adapter 0 - bus name I2C_5 */
+ pmic_init(I2C_7); /* I2C adapter 7 - bus name s3c24x0_7 */
pmic_init_max77686();
- pmic_init_max77693(I2C_2); /* I2C adapter 2 - bus name I2C_10 */
- power_muic_init(I2C_2); /* I2C adapter 2 - bus name I2C_10 */
- power_fg_init(I2C_1); /* I2C adapter 1 - bus name I2C_9 */
+ pmic_init_max77693(I2C_9); /* I2C adapter 9 - bus name soft1 */
+ power_muic_init(I2C_9); /* I2C adapter 9 - bus name soft1 */
+ power_fg_init(I2C_8); /* I2C adapter 8 - bus name soft0 */
power_bat_init(0);
p_chrg = pmic_get("MAX77693_PMIC");
diff --git a/include/configs/trats2.h b/include/configs/trats2.h
index 0e93836..3bcdfb1 100644
--- a/include/configs/trats2.h
+++ b/include/configs/trats2.h
@@ -260,30 +260,25 @@
#include <asm/arch/gpio.h>
#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
+#define CONFIG_SYS_I2C_S3C24X0
+#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000
+#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0
+#define CONFIG_MAX_I2C_NUM 8
+#define CONFIG_SYS_I2C_SOFT
#define CONFIG_SYS_I2C_SOFT_SPEED 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE 0x00
#define I2C_SOFT_DECLARATIONS2
#define CONFIG_SYS_I2C_SOFT_SPEED_2 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x00
-#define I2C_SOFT_DECLARATIONS3
-#define CONFIG_SYS_I2C_SOFT_SPEED_3 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x00
#define CONFIG_SOFT_I2C_READ_REPEATED_START
#define CONFIG_SYS_I2C_INIT_BOARD
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SOFT_I2C_MULTI_BUS
-#define CONFIG_SYS_MAX_I2C_BUS 15
-
-#define CONFIG_SOFT_I2C_I2C5_SCL exynos4x12_gpio_part1_get_nr(d0, 3)
-#define CONFIG_SOFT_I2C_I2C5_SDA exynos4x12_gpio_part1_get_nr(d0, 2)
-#define CONFIG_SOFT_I2C_I2C9_SCL exynos4x12_gpio_part1_get_nr(f1, 4)
-#define CONFIG_SOFT_I2C_I2C9_SDA exynos4x12_gpio_part1_get_nr(f1, 5)
-#define CONFIG_SOFT_I2C_I2C10_SCL exynos4x12_gpio_part2_get_nr(m2, 1)
-#define CONFIG_SOFT_I2C_I2C10_SDA exynos4x12_gpio_part2_get_nr(m2, 0)
-#define CONFIG_SOFT_I2C_GPIO_SCL get_multi_scl_pin()
-#define CONFIG_SOFT_I2C_GPIO_SDA get_multi_sda_pin()
-#define I2C_INIT multi_i2c_init()
+
+#ifndef __ASSEMBLY__
+int get_soft_i2c_scl_pin(void);
+int get_soft_i2c_sda_pin(void);
+#endif
+#define CONFIG_SOFT_I2C_GPIO_SCL get_soft_i2c_scl_pin()
+#define CONFIG_SOFT_I2C_GPIO_SDA get_soft_i2c_sda_pin()
/* POWER */
#define CONFIG_POWER
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH 1/6] driver:i2c:s3c24x0: adapt driver to new i2c
2013-11-13 14:31 ` [U-Boot] [PATCH 1/6] driver:i2c:s3c24x0: adapt driver to new i2c Piotr Wilczek
@ 2013-11-18 6:17 ` Heiko Schocher
2013-11-18 7:10 ` Piotr Wilczek
0 siblings, 1 reply; 17+ messages in thread
From: Heiko Schocher @ 2013-11-18 6:17 UTC (permalink / raw)
To: u-boot
Hello Piotr,
Am 13.11.2013 15:31, schrieb Piotr Wilczek:
> The s3c24x0 i2c driver is adapted to new i2c framework.
>
> Signed-off-by: Piotr Wilczek<p.wilczek@samsung.com>
> Signed-off-by: Kyungmin Park<kyungmin.park@samsung.com>
> Cc: Minkyu Kang<mk7.kang@samsung.com>
> Cc: Heiko Schocher<hs@denx.de>
> ---
> drivers/i2c/Makefile | 2 +-
> drivers/i2c/s3c24x0_i2c.c | 157 +++++++++++++++++++++++++++++----------------
> 2 files changed, 101 insertions(+), 58 deletions(-)
Thanks for your work! Ne real issues with your patch, but
can you squash your patchset in one patch, as we not want
to lost "git bisect" functionality.
Beside of this, only minor comments:
[...]
> diff --git a/drivers/i2c/s3c24x0_i2c.c b/drivers/i2c/s3c24x0_i2c.c
> index f77a9d1..0051cac 100644
> --- a/drivers/i2c/s3c24x0_i2c.c
> +++ b/drivers/i2c/s3c24x0_i2c.c
> @@ -23,8 +23,6 @@
> #include<i2c.h>
> #include "s3c24x0_i2c.h"
>
> -#ifdef CONFIG_HARD_I2C
> -
> #define I2C_WRITE 0
> #define I2C_READ 1
>
> @@ -127,7 +125,6 @@
> * For SPL boot some boards need i2c before SDRAM is initialised so force
> * variables to live in SRAM
> */
> -static unsigned int g_current_bus __attribute__((section(".data")));
> static struct s3c24x0_i2c_bus i2c_bus[CONFIG_MAX_I2C_NUM]
> __attribute__((section(".data")));
>
> @@ -143,6 +140,7 @@ static struct s3c24x0_i2c_bus *get_bus(unsigned int bus_idx)
> struct s3c24x0_i2c_bus *bus;
>
> bus =&i2c_bus[bus_idx];
> +
Why new line here?
> if (bus->active)
> return bus;
> }
> @@ -254,17 +252,17 @@ static void ReadWriteByte(struct s3c24x0_i2c *i2c)
> writel(readl(&i2c->iiccon)& ~I2CCON_IRPND,&i2c->iiccon);
> }
>
> -static struct s3c24x0_i2c *get_base_i2c(void)
> +static struct s3c24x0_i2c *get_base_i2c(int bus)
> {
> #ifdef CONFIG_EXYNOS4
> struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c *)(samsung_get_base_i2c()
> + (EXYNOS4_I2C_SPACING
> - * g_current_bus));
> + * bus));
> return i2c;
> #elif defined CONFIG_EXYNOS5
> struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c *)(samsung_get_base_i2c()
> + (EXYNOS5_I2C_SPACING
> - * g_current_bus));
> + * bus));
> return i2c;
> #else
> return s3c24x0_get_base_i2c();
> @@ -298,7 +296,6 @@ static void i2c_ch_init(struct s3c24x0_i2c *i2c, int speed, int slaveadd)
> writel(I2C_MODE_MT | I2C_TXRX_ENA,&i2c->iicstat);
> }
>
> -#ifdef CONFIG_I2C_MULTI_BUS
> static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
> {
> struct exynos5_hsi2c *hsregs = i2c_bus->hsregs;
> @@ -307,8 +304,10 @@ static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
> unsigned int i = 0, utemp0 = 0, utemp1 = 0;
> unsigned int t_ftl_cycle;
>
> -#if defined CONFIG_EXYNOS5
> +#if (defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5)
> clkin = get_i2c_clk();
> +#else
> + clkin = get_PCLK();
> #endif
What has this change to do with the new i2c framework?
[...]
bye,
Heiko
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH 1/6] driver:i2c:s3c24x0: adapt driver to new i2c
2013-11-18 6:17 ` Heiko Schocher
@ 2013-11-18 7:10 ` Piotr Wilczek
2013-11-18 7:19 ` Heiko Schocher
0 siblings, 1 reply; 17+ messages in thread
From: Piotr Wilczek @ 2013-11-18 7:10 UTC (permalink / raw)
To: u-boot
Hello Heiko,
> -----Original Message-----
> From: Heiko Schocher [mailto:hs at denx.de]
> Sent: Monday, November 18, 2013 7:18 AM
> To: Piotr Wilczek
> Cc: u-boot at lists.denx.de; Minkyu Kang; Kyungmin Park
> Subject: Re: [PATCH 1/6] driver:i2c:s3c24x0: adapt driver to new i2c
>
> Hello Piotr,
>
> Am 13.11.2013 15:31, schrieb Piotr Wilczek:
> > The s3c24x0 i2c driver is adapted to new i2c framework.
> >
> > Signed-off-by: Piotr Wilczek<p.wilczek@samsung.com>
> > Signed-off-by: Kyungmin Park<kyungmin.park@samsung.com>
> > Cc: Minkyu Kang<mk7.kang@samsung.com>
> > Cc: Heiko Schocher<hs@denx.de>
> > ---
> > drivers/i2c/Makefile | 2 +-
> > drivers/i2c/s3c24x0_i2c.c | 157 +++++++++++++++++++++++++++++-----
> -----------
> > 2 files changed, 101 insertions(+), 58 deletions(-)
>
> Thanks for your work! Ne real issues with your patch, but can you
> squash your patchset in one patch, as we not want to lost "git bisect"
> functionality.
Ok.
>
> Beside of this, only minor comments:
>
> [...]
> > diff --git a/drivers/i2c/s3c24x0_i2c.c b/drivers/i2c/s3c24x0_i2c.c
> > index f77a9d1..0051cac 100644
> > --- a/drivers/i2c/s3c24x0_i2c.c
> > +++ b/drivers/i2c/s3c24x0_i2c.c
> > @@ -23,8 +23,6 @@
> > #include<i2c.h>
> > #include "s3c24x0_i2c.h"
> >
> > -#ifdef CONFIG_HARD_I2C
> > -
> > #define I2C_WRITE 0
> > #define I2C_READ 1
> >
> > @@ -127,7 +125,6 @@
> > * For SPL boot some boards need i2c before SDRAM is initialised so
> force
> > * variables to live in SRAM
> > */
> > -static unsigned int g_current_bus __attribute__((section(".data")));
> > static struct s3c24x0_i2c_bus i2c_bus[CONFIG_MAX_I2C_NUM]
> > __attribute__((section(".data")));
> >
> > @@ -143,6 +140,7 @@ static struct s3c24x0_i2c_bus *get_bus(unsigned
> int bus_idx)
> > struct s3c24x0_i2c_bus *bus;
> >
> > bus =&i2c_bus[bus_idx];
> > +
>
> Why new line here?
I will remove it.
>
> > if (bus->active)
> > return bus;
> > }
> > @@ -254,17 +252,17 @@ static void ReadWriteByte(struct s3c24x0_i2c
> *i2c)
> > writel(readl(&i2c->iiccon)& ~I2CCON_IRPND,&i2c->iiccon);
> > }
> >
> > -static struct s3c24x0_i2c *get_base_i2c(void)
> > +static struct s3c24x0_i2c *get_base_i2c(int bus)
> > {
> > #ifdef CONFIG_EXYNOS4
> > struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c
> *)(samsung_get_base_i2c()
> > +
(EXYNOS4_I2C_SPACING
> > - * g_current_bus));
> > + * bus));
> > return i2c;
> > #elif defined CONFIG_EXYNOS5
> > struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c
> *)(samsung_get_base_i2c()
> > +
(EXYNOS5_I2C_SPACING
> > - * g_current_bus));
> > + * bus));
> > return i2c;
> > #else
> > return s3c24x0_get_base_i2c();
> > @@ -298,7 +296,6 @@ static void i2c_ch_init(struct s3c24x0_i2c *i2c,
> int speed, int slaveadd)
> > writel(I2C_MODE_MT | I2C_TXRX_ENA,&i2c->iicstat);
> > }
> >
> > -#ifdef CONFIG_I2C_MULTI_BUS
> > static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
> > {
> > struct exynos5_hsi2c *hsregs = i2c_bus->hsregs; @@ -307,8 +304,10
> > @@ static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
> > unsigned int i = 0, utemp0 = 0, utemp1 = 0;
> > unsigned int t_ftl_cycle;
> >
> > -#if defined CONFIG_EXYNOS5
> > +#if (defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5)
> > clkin = get_i2c_clk();
> > +#else
> > + clkin = get_PCLK();
> > #endif
>
> What has this change to do with the new i2c framework?
Actually it is related to commit shaid: 296a461
Without this change I get the uninitialized variable warning for Exynos 4.
I can make a separate patch fix for this change if you prefer.
>
> [...]
>
> bye,
> Heiko
> --
> DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Best regards,
Piotr Wilczek
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH 1/6] driver:i2c:s3c24x0: adapt driver to new i2c
2013-11-18 7:10 ` Piotr Wilczek
@ 2013-11-18 7:19 ` Heiko Schocher
0 siblings, 0 replies; 17+ messages in thread
From: Heiko Schocher @ 2013-11-18 7:19 UTC (permalink / raw)
To: u-boot
Hello Piotr,
Am 18.11.2013 08:10, schrieb Piotr Wilczek:
> Hello Heiko,
>
>> -----Original Message-----
>> From: Heiko Schocher [mailto:hs at denx.de]
>> Sent: Monday, November 18, 2013 7:18 AM
>> To: Piotr Wilczek
>> Cc: u-boot at lists.denx.de; Minkyu Kang; Kyungmin Park
>> Subject: Re: [PATCH 1/6] driver:i2c:s3c24x0: adapt driver to new i2c
>>
>> Hello Piotr,
>>
>> Am 13.11.2013 15:31, schrieb Piotr Wilczek:
>>> The s3c24x0 i2c driver is adapted to new i2c framework.
>>>
>>> Signed-off-by: Piotr Wilczek<p.wilczek@samsung.com>
>>> Signed-off-by: Kyungmin Park<kyungmin.park@samsung.com>
>>> Cc: Minkyu Kang<mk7.kang@samsung.com>
>>> Cc: Heiko Schocher<hs@denx.de>
>>> ---
>>> drivers/i2c/Makefile | 2 +-
>>> drivers/i2c/s3c24x0_i2c.c | 157 +++++++++++++++++++++++++++++-----
>> -----------
>>> 2 files changed, 101 insertions(+), 58 deletions(-)
>>
>> Thanks for your work! Ne real issues with your patch, but can you
>> squash your patchset in one patch, as we not want to lost "git bisect"
>> functionality.
> Ok.
>
>>
>> Beside of this, only minor comments:
>>
>> [...]
>>> diff --git a/drivers/i2c/s3c24x0_i2c.c b/drivers/i2c/s3c24x0_i2c.c
>>> index f77a9d1..0051cac 100644
>>> --- a/drivers/i2c/s3c24x0_i2c.c
>>> +++ b/drivers/i2c/s3c24x0_i2c.c
[...]
>>> @@ -254,17 +252,17 @@ static void ReadWriteByte(struct s3c24x0_i2c
>> *i2c)
>>> writel(readl(&i2c->iiccon)& ~I2CCON_IRPND,&i2c->iiccon);
>>> }
>>>
>>> -static struct s3c24x0_i2c *get_base_i2c(void)
>>> +static struct s3c24x0_i2c *get_base_i2c(int bus)
>>> {
>>> #ifdef CONFIG_EXYNOS4
>>> struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c
>> *)(samsung_get_base_i2c()
>>> +
> (EXYNOS4_I2C_SPACING
>>> - * g_current_bus));
>>> + * bus));
>>> return i2c;
>>> #elif defined CONFIG_EXYNOS5
>>> struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c
>> *)(samsung_get_base_i2c()
>>> +
> (EXYNOS5_I2C_SPACING
>>> - * g_current_bus));
>>> + * bus));
>>> return i2c;
>>> #else
>>> return s3c24x0_get_base_i2c();
>>> @@ -298,7 +296,6 @@ static void i2c_ch_init(struct s3c24x0_i2c *i2c,
>> int speed, int slaveadd)
>>> writel(I2C_MODE_MT | I2C_TXRX_ENA,&i2c->iicstat);
>>> }
>>>
>>> -#ifdef CONFIG_I2C_MULTI_BUS
>>> static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
>>> {
>>> struct exynos5_hsi2c *hsregs = i2c_bus->hsregs; @@ -307,8 +304,10
>>> @@ static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
>>> unsigned int i = 0, utemp0 = 0, utemp1 = 0;
>>> unsigned int t_ftl_cycle;
>>>
>>> -#if defined CONFIG_EXYNOS5
>>> +#if (defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5)
>>> clkin = get_i2c_clk();
>>> +#else
>>> + clkin = get_PCLK();
>>> #endif
>>
>> What has this change to do with the new i2c framework?
> Actually it is related to commit shaid: 296a461
> Without this change I get the uninitialized variable warning for Exynos 4.
> I can make a separate patch fix for this change if you prefer.
Yes, please.
bye,
Heiko
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH V2 1/2] driver:i2c:s3c24x0: adapt driver to new i2c
2013-11-13 14:31 [U-Boot] [PATCH 0/6] adapt s3c24x0 driver to new i2c framework Piotr Wilczek
` (5 preceding siblings ...)
2013-11-13 14:31 ` [U-Boot] [PATCH 6/6] board:trats2: switch Trats2 " Piotr Wilczek
@ 2013-11-20 9:43 ` Piotr Wilczek
2013-11-20 9:43 ` [U-Boot] [PATCH 2/2] driver:i2c:s3c24x0: fix clock init for hsi2c Piotr Wilczek
` (3 more replies)
6 siblings, 4 replies; 17+ messages in thread
From: Piotr Wilczek @ 2013-11-20 9:43 UTC (permalink / raw)
To: u-boot
This patch adapts the s3c24x0 driver to the new i2c framework.
Config file is modified for all the boards that use the driver.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Heiko Schocher <hs@denx.de>
CC: Inderpal Singh <inderpal.singh@linaro.org>
CC: David M?ller <d.mueller@elsoft.ch>
CC: Chander Kashyap <k.chander@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
---
Boards VCMA9, Arndale and Exynos5250 are compile tested only.
Boards Trats and Trats2 were hardware tested.
All boards compile clean.
Changes for V2:
- patch series squashed to one patch
- removed unnecessary blank line
- change related to hsi2c moved to saparate patch
board/samsung/smdk5250/exynos5-dt.c | 2 -
board/samsung/trats/trats.c | 21 ++---
board/samsung/trats2/trats2.c | 35 ++++++--
drivers/i2c/Makefile | 2 +-
drivers/i2c/s3c24x0_i2c.c | 152 ++++++++++++++++++++++-------------
include/configs/VCMA9.h | 8 +-
include/configs/arndale.h | 9 +--
include/configs/exynos5250-dt.h | 8 +-
include/configs/trats.h | 25 ++----
include/configs/trats2.h | 29 +++----
10 files changed, 170 insertions(+), 121 deletions(-)
diff --git a/board/samsung/smdk5250/exynos5-dt.c b/board/samsung/smdk5250/exynos5-dt.c
index 6bcc883..6aa0509 100644
--- a/board/samsung/smdk5250/exynos5-dt.c
+++ b/board/samsung/smdk5250/exynos5-dt.c
@@ -150,8 +150,6 @@ int power_init_board(void)
set_ps_hold_ctrl();
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-
if (pmic_init(I2C_PMIC))
return -1;
diff --git a/board/samsung/trats/trats.c b/board/samsung/trats/trats.c
index 7012c13..44be5fc 100644
--- a/board/samsung/trats/trats.c
+++ b/board/samsung/trats/trats.c
@@ -57,15 +57,18 @@ int board_init(void)
void i2c_init_board(void)
{
- struct exynos4_gpio_part1 *gpio1 =
- (struct exynos4_gpio_part1 *)samsung_get_base_gpio_part1();
+ int err;
struct exynos4_gpio_part2 *gpio2 =
(struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2();
- /* I2C_5 -> PMIC -> Adapter 0 */
- s5p_gpio_direction_output(&gpio1->b, 7, 1);
- s5p_gpio_direction_output(&gpio1->b, 6, 1);
- /* I2C_9 -> FG -> Adapter 1 */
+ /* I2C_5 -> PMIC */
+ err = exynos_pinmux_config(PERIPH_ID_I2C5, PINMUX_FLAG_NONE);
+ if (err) {
+ debug("I2C%d not configured\n", (I2C_5));
+ return;
+ }
+
+ /* I2C_8 -> FG */
s5p_gpio_direction_output(&gpio2->y4, 0, 1);
s5p_gpio_direction_output(&gpio2->y4, 1, 1);
}
@@ -290,10 +293,10 @@ int power_init_board(void)
* The FUEL_GAUGE is marked as I2C9 on the schematic, but connected
* to logical I2C adapter 1
*/
- ret = pmic_init(I2C_0);
+ ret = pmic_init(I2C_5);
ret |= pmic_init_max8997();
- ret |= power_fg_init(I2C_1);
- ret |= power_muic_init(I2C_0);
+ ret |= power_fg_init(I2C_8);
+ ret |= power_muic_init(I2C_5);
ret |= power_bat_init(0);
if (ret)
return ret;
diff --git a/board/samsung/trats2/trats2.c b/board/samsung/trats2/trats2.c
index d44d825..8df85ee 100644
--- a/board/samsung/trats2/trats2.c
+++ b/board/samsung/trats2/trats2.c
@@ -115,12 +115,17 @@ static void board_external_gpio_init(void)
#ifdef CONFIG_SYS_I2C_INIT_BOARD
static void board_init_i2c(void)
{
+ int err;
+
gpio1 = (struct exynos4x12_gpio_part1 *)EXYNOS4X12_GPIO_PART1_BASE;
gpio2 = (struct exynos4x12_gpio_part2 *)EXYNOS4X12_GPIO_PART2_BASE;
/* I2C_7 */
- s5p_gpio_direction_output(&gpio1->d0, 2, 1);
- s5p_gpio_direction_output(&gpio1->d0, 3, 1);
+ err = exynos_pinmux_config(PERIPH_ID_I2C7, PINMUX_FLAG_NONE);
+ if (err) {
+ debug("I2C%d not configured\n", (I2C_7));
+ return;
+ }
/* I2C_8 */
s5p_gpio_direction_output(&gpio1->f1, 4, 1);
@@ -132,6 +137,24 @@ static void board_init_i2c(void)
}
#endif
+#ifdef CONFIG_SYS_I2C_SOFT
+int get_soft_i2c_scl_pin(void)
+{
+ if (I2C_ADAP_HWNR)
+ return exynos4x12_gpio_part2_get_nr(m2, 1); /* I2C9 */
+ else
+ return exynos4x12_gpio_part1_get_nr(f1, 4); /* I2C8 */
+}
+
+int get_soft_i2c_sda_pin(void)
+{
+ if (I2C_ADAP_HWNR)
+ return exynos4x12_gpio_part2_get_nr(m2, 0); /* I2C9 */
+ else
+ return exynos4x12_gpio_part1_get_nr(f1, 5); /* I2C8 */
+}
+#endif
+
int board_early_init_f(void)
{
check_hw_revision();
@@ -167,11 +190,11 @@ int power_init_board(void)
#ifdef CONFIG_SYS_I2C_INIT_BOARD
board_init_i2c();
#endif
- pmic_init(I2C_0); /* I2C adapter 0 - bus name I2C_5 */
+ pmic_init(I2C_7); /* I2C adapter 7 - bus name s3c24x0_7 */
pmic_init_max77686();
- pmic_init_max77693(I2C_2); /* I2C adapter 2 - bus name I2C_10 */
- power_muic_init(I2C_2); /* I2C adapter 2 - bus name I2C_10 */
- power_fg_init(I2C_1); /* I2C adapter 1 - bus name I2C_9 */
+ pmic_init_max77693(I2C_9); /* I2C adapter 9 - bus name soft1 */
+ power_muic_init(I2C_9); /* I2C adapter 9 - bus name soft1 */
+ power_fg_init(I2C_8); /* I2C adapter 8 - bus name soft0 */
power_bat_init(0);
p_chrg = pmic_get("MAX77693_PMIC");
diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
index 553b519..fa3a875 100644
--- a/drivers/i2c/Makefile
+++ b/drivers/i2c/Makefile
@@ -12,7 +12,6 @@ obj-$(CONFIG_I2C_MVTWSI) += mvtwsi.o
obj-$(CONFIG_I2C_MV) += mv_i2c.o
obj-$(CONFIG_I2C_MXS) += mxs_i2c.o
obj-$(CONFIG_PCA9564_I2C) += pca9564_i2c.o
-obj-$(CONFIG_DRIVER_S3C24X0_I2C) += s3c24x0_i2c.o
obj-$(CONFIG_TSI108_I2C) += tsi108_i2c.o
obj-$(CONFIG_U8500_I2C) += u8500_i2c.o
obj-$(CONFIG_SH_SH7734_I2C) += sh_sh7734_i2c.o
@@ -24,6 +23,7 @@ obj-$(CONFIG_SYS_I2C_OMAP24XX) += omap24xx_i2c.o
obj-$(CONFIG_SYS_I2C_OMAP34XX) += omap24xx_i2c.o
obj-$(CONFIG_SYS_I2C_PPC4XX) += ppc4xx_i2c.o
obj-$(CONFIG_SYS_I2C_RCAR) += rcar_i2c.o
+obj-$(CONFIG_SYS_I2C_S3C24X0) += s3c24x0_i2c.o
obj-$(CONFIG_SYS_I2C_SH) += sh_i2c.o
obj-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o
obj-$(CONFIG_SYS_I2C_TEGRA) += tegra_i2c.o
diff --git a/drivers/i2c/s3c24x0_i2c.c b/drivers/i2c/s3c24x0_i2c.c
index f77a9d1..5dc35e7 100644
--- a/drivers/i2c/s3c24x0_i2c.c
+++ b/drivers/i2c/s3c24x0_i2c.c
@@ -23,8 +23,6 @@
#include <i2c.h>
#include "s3c24x0_i2c.h"
-#ifdef CONFIG_HARD_I2C
-
#define I2C_WRITE 0
#define I2C_READ 1
@@ -127,7 +125,6 @@
* For SPL boot some boards need i2c before SDRAM is initialised so force
* variables to live in SRAM
*/
-static unsigned int g_current_bus __attribute__((section(".data")));
static struct s3c24x0_i2c_bus i2c_bus[CONFIG_MAX_I2C_NUM]
__attribute__((section(".data")));
@@ -254,17 +251,17 @@ static void ReadWriteByte(struct s3c24x0_i2c *i2c)
writel(readl(&i2c->iiccon) & ~I2CCON_IRPND, &i2c->iiccon);
}
-static struct s3c24x0_i2c *get_base_i2c(void)
+static struct s3c24x0_i2c *get_base_i2c(int bus)
{
#ifdef CONFIG_EXYNOS4
struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c *)(samsung_get_base_i2c()
+ (EXYNOS4_I2C_SPACING
- * g_current_bus));
+ * bus));
return i2c;
#elif defined CONFIG_EXYNOS5
struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c *)(samsung_get_base_i2c()
+ (EXYNOS5_I2C_SPACING
- * g_current_bus));
+ * bus));
return i2c;
#else
return s3c24x0_get_base_i2c();
@@ -298,7 +295,6 @@ static void i2c_ch_init(struct s3c24x0_i2c *i2c, int speed, int slaveadd)
writel(I2C_MODE_MT | I2C_TXRX_ENA, &i2c->iicstat);
}
-#ifdef CONFIG_I2C_MULTI_BUS
static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
{
struct exynos5_hsi2c *hsregs = i2c_bus->hsregs;
@@ -330,7 +326,6 @@ static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
}
return -1;
}
-#endif
static void hsi2c_ch_init(struct s3c24x0_i2c_bus *i2c_bus)
{
@@ -401,49 +396,18 @@ static void exynos5_i2c_reset(struct s3c24x0_i2c_bus *i2c_bus)
hsi2c_ch_init(i2c_bus);
}
-/*
- * MULTI BUS I2C support
- */
-
-#ifdef CONFIG_I2C_MULTI_BUS
-int i2c_set_bus_num(unsigned int bus)
-{
- struct s3c24x0_i2c_bus *i2c_bus;
-
- i2c_bus = get_bus(bus);
- if (!i2c_bus)
- return -1;
- g_current_bus = bus;
-
- if (i2c_bus->is_highspeed) {
- if (hsi2c_get_clk_details(i2c_bus))
- return -1;
- hsi2c_ch_init(i2c_bus);
- } else {
- i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency,
- CONFIG_SYS_I2C_SLAVE);
- }
-
- return 0;
-}
-
-unsigned int i2c_get_bus_num(void)
-{
- return g_current_bus;
-}
-#endif
-
-void i2c_init(int speed, int slaveadd)
+static void s3c24x0_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd)
{
struct s3c24x0_i2c *i2c;
+ struct s3c24x0_i2c_bus *bus;
+
#if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5)
struct s3c24x0_gpio *gpio = s3c24x0_get_base_gpio();
#endif
ulong start_time = get_timer(0);
/* By default i2c channel 0 is the current bus */
- g_current_bus = 0;
- i2c = get_base_i2c();
+ i2c = get_base_i2c(adap->hwadapnr);
/*
* In case the previous transfer is still going, wait to give it a
@@ -505,6 +469,10 @@ void i2c_init(int speed, int slaveadd)
}
#endif /* #if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5) */
i2c_ch_init(i2c, speed, slaveadd);
+
+ bus = &i2c_bus[adap->hwadapnr];
+ bus->active = true;
+ bus->regs = i2c;
}
/*
@@ -728,6 +696,29 @@ static int hsi2c_read(struct exynos5_hsi2c *i2c,
return rv;
}
+static unsigned int s3c24x0_i2c_set_bus_speed(struct i2c_adapter *adap,
+ unsigned int speed)
+{
+ struct s3c24x0_i2c_bus *i2c_bus;
+
+ i2c_bus = get_bus(adap->hwadapnr);
+ if (!i2c_bus)
+ return -1;
+
+ i2c_bus->clock_frequency = speed;
+
+ if (i2c_bus->is_highspeed) {
+ if (hsi2c_get_clk_details(i2c_bus))
+ return -1;
+ hsi2c_ch_init(i2c_bus);
+ } else {
+ i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE);
+ }
+
+ return 0;
+}
+
/*
* cmd_type is 0 for write, 1 for read.
*
@@ -840,13 +831,13 @@ bailout:
return result;
}
-int i2c_probe(uchar chip)
+static int s3c24x0_i2c_probe(struct i2c_adapter *adap, uchar chip)
{
struct s3c24x0_i2c_bus *i2c_bus;
uchar buf[1];
int ret;
- i2c_bus = get_bus(g_current_bus);
+ i2c_bus = get_bus(adap->hwadapnr);
if (!i2c_bus)
return -1;
buf[0] = 0;
@@ -864,11 +855,11 @@ int i2c_probe(uchar chip)
I2C_READ, chip << 1, 0, 0, buf, 1);
}
-
return ret != I2C_OK;
}
-int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
+static int s3c24x0_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
+ int alen, uchar *buffer, int len)
{
struct s3c24x0_i2c_bus *i2c_bus;
uchar xaddr[4];
@@ -902,7 +893,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
chip |= ((addr >> (alen * 8)) &
CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
#endif
- i2c_bus = get_bus(g_current_bus);
+ i2c_bus = get_bus(adap->hwadapnr);
if (!i2c_bus)
return -1;
@@ -922,7 +913,8 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
return 0;
}
-int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
+static int s3c24x0_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
+ int alen, uchar *buffer, int len)
{
struct s3c24x0_i2c_bus *i2c_bus;
uchar xaddr[4];
@@ -955,7 +947,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
chip |= ((addr >> (alen * 8)) &
CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
#endif
- i2c_bus = get_bus(g_current_bus);
+ i2c_bus = get_bus(adap->hwadapnr);
if (!i2c_bus)
return -1;
@@ -1001,8 +993,8 @@ static void process_nodes(const void *blob, int node_list[], int count,
bus->id = pinmux_decode_periph_id(blob, node);
bus->clock_frequency = fdtdec_get_int(blob, node,
- "clock-frequency",
- CONFIG_SYS_I2C_SPEED);
+ "clock-frequency",
+ CONFIG_SYS_I2C_S3C24X0_SPEED);
bus->node = node;
bus->bus_num = i;
exynos_pinmux_config(bus->id, 0);
@@ -1044,7 +1036,6 @@ int i2c_get_bus_num_fdt(int node)
return -1;
}
-#ifdef CONFIG_I2C_MULTI_BUS
int i2c_reset_port_fdt(const void *blob, int node)
{
struct s3c24x0_i2c_bus *i2c_bus;
@@ -1068,12 +1059,61 @@ int i2c_reset_port_fdt(const void *blob, int node)
hsi2c_ch_init(i2c_bus);
} else {
i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency,
- CONFIG_SYS_I2C_SLAVE);
+ CONFIG_SYS_I2C_S3C24X0_SLAVE);
}
return 0;
}
#endif
-#endif
-#endif /* CONFIG_HARD_I2C */
+/*
+ * Register s3c24x0 i2c adapters
+ */
+U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_0, s3c24x0_i2c_init, s3c24x0_i2c_probe,
+ s3c24x0_i2c_read, s3c24x0_i2c_write,
+ s3c24x0_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_S3C24X0_SPEED,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE,
+ 0)
+U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_1, s3c24x0_i2c_init, s3c24x0_i2c_probe,
+ s3c24x0_i2c_read, s3c24x0_i2c_write,
+ s3c24x0_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_S3C24X0_SPEED,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE,
+ 1)
+U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_2, s3c24x0_i2c_init, s3c24x0_i2c_probe,
+ s3c24x0_i2c_read, s3c24x0_i2c_write,
+ s3c24x0_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_S3C24X0_SPEED,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE,
+ 2)
+U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_3, s3c24x0_i2c_init, s3c24x0_i2c_probe,
+ s3c24x0_i2c_read, s3c24x0_i2c_write,
+ s3c24x0_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_S3C24X0_SPEED,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE,
+ 3)
+U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_4, s3c24x0_i2c_init, s3c24x0_i2c_probe,
+ s3c24x0_i2c_read, s3c24x0_i2c_write,
+ s3c24x0_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_S3C24X0_SPEED,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE,
+ 4)
+U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_5, s3c24x0_i2c_init, s3c24x0_i2c_probe,
+ s3c24x0_i2c_read, s3c24x0_i2c_write,
+ s3c24x0_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_S3C24X0_SPEED,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE,
+ 5)
+U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_6, s3c24x0_i2c_init, s3c24x0_i2c_probe,
+ s3c24x0_i2c_read, s3c24x0_i2c_write,
+ s3c24x0_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_S3C24X0_SPEED,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE,
+ 6)
+U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_7, s3c24x0_i2c_init, s3c24x0_i2c_probe,
+ s3c24x0_i2c_read, s3c24x0_i2c_write,
+ s3c24x0_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_S3C24X0_SPEED,
+ CONFIG_SYS_I2C_S3C24X0_SLAVE,
+ 7)
diff --git a/include/configs/VCMA9.h b/include/configs/VCMA9.h
index 79a6079..57b620d 100644
--- a/include/configs/VCMA9.h
+++ b/include/configs/VCMA9.h
@@ -73,12 +73,12 @@
* the MPL VCMA9 is equipped with an ATMEL 24C256 EEPROM at
* address 0x50 with 16bit addressing
*/
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */
-#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave addr */
+#define CONFIG_SYS_I2C
/* we use the built-in I2C controller */
-#define CONFIG_DRIVER_S3C24X0_I2C
+#define CONFIG_SYS_I2C_S3C24X0
+#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* I2C speed */
+#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x7F /* I2C slave addr */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
diff --git a/include/configs/arndale.h b/include/configs/arndale.h
index 45fa047..ea8753b 100644
--- a/include/configs/arndale.h
+++ b/include/configs/arndale.h
@@ -214,13 +214,12 @@
/* I2C */
#define CONFIG_SYS_I2C_INIT_BOARD
-#define CONFIG_HARD_I2C
+#define CONFIG_SYS_I2C
#define CONFIG_CMD_I2C
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 Kbps */
-#define CONFIG_DRIVER_S3C24X0_I2C
-#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* 100 Kbps */
+#define CONFIG_SYS_I2C_S3C24X0
#define CONFIG_MAX_I2C_NUM 8
-#define CONFIG_SYS_I2C_SLAVE 0x0
+#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x0
#define CONFIG_I2C_EDID
/* PMIC */
diff --git a/include/configs/exynos5250-dt.h b/include/configs/exynos5250-dt.h
index bdefee1..0155322 100644
--- a/include/configs/exynos5250-dt.h
+++ b/include/configs/exynos5250-dt.h
@@ -249,13 +249,13 @@
/* I2C */
#define CONFIG_SYS_I2C_INIT_BOARD
-#define CONFIG_HARD_I2C
+#define CONFIG_SYS_I2C
#define CONFIG_CMD_I2C
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 Kbps */
-#define CONFIG_DRIVER_S3C24X0_I2C
+#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* 100 Kbps */
+#define CONFIG_SYS_I2C_S3C24X0
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_MAX_I2C_NUM 8
-#define CONFIG_SYS_I2C_SLAVE 0x0
+#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x0
#define CONFIG_I2C_EDID
/* PMIC */
diff --git a/include/configs/trats.h b/include/configs/trats.h
index 3d080c4..f163303 100644
--- a/include/configs/trats.h
+++ b/include/configs/trats.h
@@ -16,6 +16,7 @@
*/
#define CONFIG_SAMSUNG /* in a SAMSUNG core */
#define CONFIG_S5P /* which is in a S5P Family */
+#define CONFIG_EXYNOS4 /* which is in a EXYNOS4XXX */
#define CONFIG_EXYNOS4210 /* which is in a EXYNOS4210 */
#define CONFIG_TRATS /* working with TRATS */
#define CONFIG_TIZEN /* TIZEN lib */
@@ -268,31 +269,21 @@
#define CONFIG_SYS_CACHELINE_SIZE 32
#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_S3C24X0
+#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000
+#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0xFE
+#define CONFIG_MAX_I2C_NUM 8
#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
#define CONFIG_SYS_I2C_SOFT_SPEED 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
-#define I2C_SOFT_DECLARATIONS2
-#define CONFIG_SYS_I2C_SOFT_SPEED_2 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F
+#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F
#define CONFIG_SOFT_I2C_READ_REPEATED_START
#define CONFIG_SYS_I2C_INIT_BOARD
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SOFT_I2C_MULTI_BUS
-#define CONFIG_SYS_MAX_I2C_BUS 15
#include <asm/arch/gpio.h>
-/* I2C PMIC */
-#define CONFIG_SOFT_I2C_I2C5_SCL exynos4_gpio_part1_get_nr(b, 7)
-#define CONFIG_SOFT_I2C_I2C5_SDA exynos4_gpio_part1_get_nr(b, 6)
-
/* I2C FG */
-#define CONFIG_SOFT_I2C_I2C9_SCL exynos4_gpio_part2_get_nr(y4, 1)
-#define CONFIG_SOFT_I2C_I2C9_SDA exynos4_gpio_part2_get_nr(y4, 0)
-
-#define CONFIG_SOFT_I2C_GPIO_SCL get_multi_scl_pin()
-#define CONFIG_SOFT_I2C_GPIO_SDA get_multi_sda_pin()
-#define I2C_INIT multi_i2c_init()
+#define CONFIG_SOFT_I2C_GPIO_SCL exynos4_gpio_part2_get_nr(y4, 1)
+#define CONFIG_SOFT_I2C_GPIO_SDA exynos4_gpio_part2_get_nr(y4, 0)
#define CONFIG_POWER
#define CONFIG_POWER_I2C
diff --git a/include/configs/trats2.h b/include/configs/trats2.h
index 0e93836..3bcdfb1 100644
--- a/include/configs/trats2.h
+++ b/include/configs/trats2.h
@@ -260,30 +260,25 @@
#include <asm/arch/gpio.h>
#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
+#define CONFIG_SYS_I2C_S3C24X0
+#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000
+#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0
+#define CONFIG_MAX_I2C_NUM 8
+#define CONFIG_SYS_I2C_SOFT
#define CONFIG_SYS_I2C_SOFT_SPEED 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE 0x00
#define I2C_SOFT_DECLARATIONS2
#define CONFIG_SYS_I2C_SOFT_SPEED_2 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x00
-#define I2C_SOFT_DECLARATIONS3
-#define CONFIG_SYS_I2C_SOFT_SPEED_3 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x00
#define CONFIG_SOFT_I2C_READ_REPEATED_START
#define CONFIG_SYS_I2C_INIT_BOARD
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SOFT_I2C_MULTI_BUS
-#define CONFIG_SYS_MAX_I2C_BUS 15
-
-#define CONFIG_SOFT_I2C_I2C5_SCL exynos4x12_gpio_part1_get_nr(d0, 3)
-#define CONFIG_SOFT_I2C_I2C5_SDA exynos4x12_gpio_part1_get_nr(d0, 2)
-#define CONFIG_SOFT_I2C_I2C9_SCL exynos4x12_gpio_part1_get_nr(f1, 4)
-#define CONFIG_SOFT_I2C_I2C9_SDA exynos4x12_gpio_part1_get_nr(f1, 5)
-#define CONFIG_SOFT_I2C_I2C10_SCL exynos4x12_gpio_part2_get_nr(m2, 1)
-#define CONFIG_SOFT_I2C_I2C10_SDA exynos4x12_gpio_part2_get_nr(m2, 0)
-#define CONFIG_SOFT_I2C_GPIO_SCL get_multi_scl_pin()
-#define CONFIG_SOFT_I2C_GPIO_SDA get_multi_sda_pin()
-#define I2C_INIT multi_i2c_init()
+
+#ifndef __ASSEMBLY__
+int get_soft_i2c_scl_pin(void);
+int get_soft_i2c_sda_pin(void);
+#endif
+#define CONFIG_SOFT_I2C_GPIO_SCL get_soft_i2c_scl_pin()
+#define CONFIG_SOFT_I2C_GPIO_SDA get_soft_i2c_sda_pin()
/* POWER */
#define CONFIG_POWER
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH 2/2] driver:i2c:s3c24x0: fix clock init for hsi2c
2013-11-20 9:43 ` [U-Boot] [PATCH V2 1/2] driver:i2c:s3c24x0: adapt driver to new i2c Piotr Wilczek
@ 2013-11-20 9:43 ` Piotr Wilczek
2013-12-09 6:50 ` [U-Boot] [U-Boot, " Heiko Schocher
2013-11-20 12:08 ` [U-Boot] [PATCH V2 1/2] driver:i2c:s3c24x0: adapt driver to new i2c Naveen Krishna Ch
` (2 subsequent siblings)
3 siblings, 1 reply; 17+ messages in thread
From: Piotr Wilczek @ 2013-11-20 9:43 UTC (permalink / raw)
To: u-boot
Fix clock value initialisation for Exynos other than Exynos5 for hsi2c.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
---
drivers/i2c/s3c24x0_i2c.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/i2c/s3c24x0_i2c.c b/drivers/i2c/s3c24x0_i2c.c
index 5dc35e7..1e9dba0 100644
--- a/drivers/i2c/s3c24x0_i2c.c
+++ b/drivers/i2c/s3c24x0_i2c.c
@@ -303,8 +303,10 @@ static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
unsigned int i = 0, utemp0 = 0, utemp1 = 0;
unsigned int t_ftl_cycle;
-#if defined CONFIG_EXYNOS5
+#if (defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5)
clkin = get_i2c_clk();
+#else
+ clkin = get_PCLK();
#endif
/* FPCLK / FI2C =
* (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + 2 * FLT_CYCLE
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH V2 1/2] driver:i2c:s3c24x0: adapt driver to new i2c
2013-11-20 9:43 ` [U-Boot] [PATCH V2 1/2] driver:i2c:s3c24x0: adapt driver to new i2c Piotr Wilczek
2013-11-20 9:43 ` [U-Boot] [PATCH 2/2] driver:i2c:s3c24x0: fix clock init for hsi2c Piotr Wilczek
@ 2013-11-20 12:08 ` Naveen Krishna Ch
2013-11-20 14:15 ` Naveen Krishna Ch
2013-12-09 6:50 ` [U-Boot] [U-Boot, V2, " Heiko Schocher
3 siblings, 0 replies; 17+ messages in thread
From: Naveen Krishna Ch @ 2013-11-20 12:08 UTC (permalink / raw)
To: u-boot
Hello All,
On 20 November 2013 15:13, Piotr Wilczek <p.wilczek@samsung.com> wrote:
> This patch adapts the s3c24x0 driver to the new i2c framework.
> Config file is modified for all the boards that use the driver.
>
> Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> CC: Minkyu Kang <mk7.kang@samsung.com>
> CC: Heiko Schocher <hs@denx.de>
> CC: Inderpal Singh <inderpal.singh@linaro.org>
> CC: David M?ller <d.mueller@elsoft.ch>
> CC: Chander Kashyap <k.chander@samsung.com>
> CC: Lukasz Majewski <l.majewski@samsung.com>
> ---
> Boards VCMA9, Arndale and Exynos5250 are compile tested only.
> Boards Trats and Trats2 were hardware tested.
> All boards compile clean.
>
> Changes for V2:
> - patch series squashed to one patch
> - removed unnecessary blank line
> - change related to hsi2c moved to saparate patch
>
> board/samsung/smdk5250/exynos5-dt.c | 2 -
> board/samsung/trats/trats.c | 21 ++---
> board/samsung/trats2/trats2.c | 35 ++++++--
> drivers/i2c/Makefile | 2 +-
> drivers/i2c/s3c24x0_i2c.c | 152 ++++++++++++++++++++++-------------
> include/configs/VCMA9.h | 8 +-
> include/configs/arndale.h | 9 +--
> include/configs/exynos5250-dt.h | 8 +-
> include/configs/trats.h | 25 ++----
> include/configs/trats2.h | 29 +++----
> 10 files changed, 170 insertions(+), 121 deletions(-)
>
> diff --git a/board/samsung/smdk5250/exynos5-dt.c b/board/samsung/smdk5250/exynos5-dt.c
> index 6bcc883..6aa0509 100644
> --- a/board/samsung/smdk5250/exynos5-dt.c
> +++ b/board/samsung/smdk5250/exynos5-dt.c
> @@ -150,8 +150,6 @@ int power_init_board(void)
>
> set_ps_hold_ctrl();
>
> - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
> -
> if (pmic_init(I2C_PMIC))
> return -1;
>
> diff --git a/board/samsung/trats/trats.c b/board/samsung/trats/trats.c
> index 7012c13..44be5fc 100644
> --- a/board/samsung/trats/trats.c
> +++ b/board/samsung/trats/trats.c
> @@ -57,15 +57,18 @@ int board_init(void)
>
> void i2c_init_board(void)
> {
> - struct exynos4_gpio_part1 *gpio1 =
> - (struct exynos4_gpio_part1 *)samsung_get_base_gpio_part1();
> + int err;
> struct exynos4_gpio_part2 *gpio2 =
> (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2();
>
> - /* I2C_5 -> PMIC -> Adapter 0 */
> - s5p_gpio_direction_output(&gpio1->b, 7, 1);
> - s5p_gpio_direction_output(&gpio1->b, 6, 1);
> - /* I2C_9 -> FG -> Adapter 1 */
> + /* I2C_5 -> PMIC */
> + err = exynos_pinmux_config(PERIPH_ID_I2C5, PINMUX_FLAG_NONE);
> + if (err) {
> + debug("I2C%d not configured\n", (I2C_5));
> + return;
> + }
> +
> + /* I2C_8 -> FG */
> s5p_gpio_direction_output(&gpio2->y4, 0, 1);
> s5p_gpio_direction_output(&gpio2->y4, 1, 1);
> }
> @@ -290,10 +293,10 @@ int power_init_board(void)
> * The FUEL_GAUGE is marked as I2C9 on the schematic, but connected
> * to logical I2C adapter 1
> */
> - ret = pmic_init(I2C_0);
> + ret = pmic_init(I2C_5);
> ret |= pmic_init_max8997();
> - ret |= power_fg_init(I2C_1);
> - ret |= power_muic_init(I2C_0);
> + ret |= power_fg_init(I2C_8);
> + ret |= power_muic_init(I2C_5);
> ret |= power_bat_init(0);
> if (ret)
> return ret;
> diff --git a/board/samsung/trats2/trats2.c b/board/samsung/trats2/trats2.c
> index d44d825..8df85ee 100644
> --- a/board/samsung/trats2/trats2.c
> +++ b/board/samsung/trats2/trats2.c
> @@ -115,12 +115,17 @@ static void board_external_gpio_init(void)
> #ifdef CONFIG_SYS_I2C_INIT_BOARD
> static void board_init_i2c(void)
> {
> + int err;
> +
> gpio1 = (struct exynos4x12_gpio_part1 *)EXYNOS4X12_GPIO_PART1_BASE;
> gpio2 = (struct exynos4x12_gpio_part2 *)EXYNOS4X12_GPIO_PART2_BASE;
>
> /* I2C_7 */
> - s5p_gpio_direction_output(&gpio1->d0, 2, 1);
> - s5p_gpio_direction_output(&gpio1->d0, 3, 1);
> + err = exynos_pinmux_config(PERIPH_ID_I2C7, PINMUX_FLAG_NONE);
> + if (err) {
> + debug("I2C%d not configured\n", (I2C_7));
> + return;
> + }
>
> /* I2C_8 */
> s5p_gpio_direction_output(&gpio1->f1, 4, 1);
> @@ -132,6 +137,24 @@ static void board_init_i2c(void)
> }
> #endif
>
> +#ifdef CONFIG_SYS_I2C_SOFT
> +int get_soft_i2c_scl_pin(void)
> +{
> + if (I2C_ADAP_HWNR)
> + return exynos4x12_gpio_part2_get_nr(m2, 1); /* I2C9 */
> + else
> + return exynos4x12_gpio_part1_get_nr(f1, 4); /* I2C8 */
> +}
> +
> +int get_soft_i2c_sda_pin(void)
> +{
> + if (I2C_ADAP_HWNR)
> + return exynos4x12_gpio_part2_get_nr(m2, 0); /* I2C9 */
> + else
> + return exynos4x12_gpio_part1_get_nr(f1, 5); /* I2C8 */
> +}
> +#endif
> +
> int board_early_init_f(void)
> {
> check_hw_revision();
> @@ -167,11 +190,11 @@ int power_init_board(void)
> #ifdef CONFIG_SYS_I2C_INIT_BOARD
> board_init_i2c();
> #endif
> - pmic_init(I2C_0); /* I2C adapter 0 - bus name I2C_5 */
> + pmic_init(I2C_7); /* I2C adapter 7 - bus name s3c24x0_7 */
> pmic_init_max77686();
> - pmic_init_max77693(I2C_2); /* I2C adapter 2 - bus name I2C_10 */
> - power_muic_init(I2C_2); /* I2C adapter 2 - bus name I2C_10 */
> - power_fg_init(I2C_1); /* I2C adapter 1 - bus name I2C_9 */
> + pmic_init_max77693(I2C_9); /* I2C adapter 9 - bus name soft1 */
> + power_muic_init(I2C_9); /* I2C adapter 9 - bus name soft1 */
> + power_fg_init(I2C_8); /* I2C adapter 8 - bus name soft0 */
> power_bat_init(0);
>
> p_chrg = pmic_get("MAX77693_PMIC");
> diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
> index 553b519..fa3a875 100644
> --- a/drivers/i2c/Makefile
> +++ b/drivers/i2c/Makefile
> @@ -12,7 +12,6 @@ obj-$(CONFIG_I2C_MVTWSI) += mvtwsi.o
> obj-$(CONFIG_I2C_MV) += mv_i2c.o
> obj-$(CONFIG_I2C_MXS) += mxs_i2c.o
> obj-$(CONFIG_PCA9564_I2C) += pca9564_i2c.o
> -obj-$(CONFIG_DRIVER_S3C24X0_I2C) += s3c24x0_i2c.o
> obj-$(CONFIG_TSI108_I2C) += tsi108_i2c.o
> obj-$(CONFIG_U8500_I2C) += u8500_i2c.o
> obj-$(CONFIG_SH_SH7734_I2C) += sh_sh7734_i2c.o
> @@ -24,6 +23,7 @@ obj-$(CONFIG_SYS_I2C_OMAP24XX) += omap24xx_i2c.o
> obj-$(CONFIG_SYS_I2C_OMAP34XX) += omap24xx_i2c.o
> obj-$(CONFIG_SYS_I2C_PPC4XX) += ppc4xx_i2c.o
> obj-$(CONFIG_SYS_I2C_RCAR) += rcar_i2c.o
> +obj-$(CONFIG_SYS_I2C_S3C24X0) += s3c24x0_i2c.o
> obj-$(CONFIG_SYS_I2C_SH) += sh_i2c.o
> obj-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o
> obj-$(CONFIG_SYS_I2C_TEGRA) += tegra_i2c.o
> diff --git a/drivers/i2c/s3c24x0_i2c.c b/drivers/i2c/s3c24x0_i2c.c
> index f77a9d1..5dc35e7 100644
> --- a/drivers/i2c/s3c24x0_i2c.c
> +++ b/drivers/i2c/s3c24x0_i2c.c
> @@ -23,8 +23,6 @@
> #include <i2c.h>
> #include "s3c24x0_i2c.h"
>
> -#ifdef CONFIG_HARD_I2C
> -
> #define I2C_WRITE 0
> #define I2C_READ 1
>
> @@ -127,7 +125,6 @@
> * For SPL boot some boards need i2c before SDRAM is initialised so force
> * variables to live in SRAM
> */
> -static unsigned int g_current_bus __attribute__((section(".data")));
> static struct s3c24x0_i2c_bus i2c_bus[CONFIG_MAX_I2C_NUM]
> __attribute__((section(".data")));
>
> @@ -254,17 +251,17 @@ static void ReadWriteByte(struct s3c24x0_i2c *i2c)
> writel(readl(&i2c->iiccon) & ~I2CCON_IRPND, &i2c->iiccon);
> }
>
> -static struct s3c24x0_i2c *get_base_i2c(void)
> +static struct s3c24x0_i2c *get_base_i2c(int bus)
> {
> #ifdef CONFIG_EXYNOS4
> struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c *)(samsung_get_base_i2c()
> + (EXYNOS4_I2C_SPACING
> - * g_current_bus));
> + * bus));
> return i2c;
> #elif defined CONFIG_EXYNOS5
> struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c *)(samsung_get_base_i2c()
> + (EXYNOS5_I2C_SPACING
> - * g_current_bus));
> + * bus));
> return i2c;
> #else
> return s3c24x0_get_base_i2c();
> @@ -298,7 +295,6 @@ static void i2c_ch_init(struct s3c24x0_i2c *i2c, int speed, int slaveadd)
> writel(I2C_MODE_MT | I2C_TXRX_ENA, &i2c->iicstat);
> }
>
> -#ifdef CONFIG_I2C_MULTI_BUS
> static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
> {
> struct exynos5_hsi2c *hsregs = i2c_bus->hsregs;
> @@ -330,7 +326,6 @@ static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
> }
> return -1;
> }
> -#endif
>
> static void hsi2c_ch_init(struct s3c24x0_i2c_bus *i2c_bus)
> {
> @@ -401,49 +396,18 @@ static void exynos5_i2c_reset(struct s3c24x0_i2c_bus *i2c_bus)
> hsi2c_ch_init(i2c_bus);
> }
>
> -/*
> - * MULTI BUS I2C support
> - */
> -
> -#ifdef CONFIG_I2C_MULTI_BUS
> -int i2c_set_bus_num(unsigned int bus)
> -{
> - struct s3c24x0_i2c_bus *i2c_bus;
> -
> - i2c_bus = get_bus(bus);
> - if (!i2c_bus)
> - return -1;
> - g_current_bus = bus;
> -
> - if (i2c_bus->is_highspeed) {
> - if (hsi2c_get_clk_details(i2c_bus))
> - return -1;
> - hsi2c_ch_init(i2c_bus);
> - } else {
> - i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency,
> - CONFIG_SYS_I2C_SLAVE);
> - }
> -
> - return 0;
> -}
> -
> -unsigned int i2c_get_bus_num(void)
> -{
> - return g_current_bus;
> -}
> -#endif
> -
> -void i2c_init(int speed, int slaveadd)
> +static void s3c24x0_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd)
> {
> struct s3c24x0_i2c *i2c;
> + struct s3c24x0_i2c_bus *bus;
> +
> #if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5)
> struct s3c24x0_gpio *gpio = s3c24x0_get_base_gpio();
> #endif
> ulong start_time = get_timer(0);
>
> /* By default i2c channel 0 is the current bus */
> - g_current_bus = 0;
> - i2c = get_base_i2c();
> + i2c = get_base_i2c(adap->hwadapnr);
>
> /*
> * In case the previous transfer is still going, wait to give it a
> @@ -505,6 +469,10 @@ void i2c_init(int speed, int slaveadd)
> }
> #endif /* #if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5) */
> i2c_ch_init(i2c, speed, slaveadd);
> +
> + bus = &i2c_bus[adap->hwadapnr];
> + bus->active = true;
> + bus->regs = i2c;
> }
>
> /*
> @@ -728,6 +696,29 @@ static int hsi2c_read(struct exynos5_hsi2c *i2c,
> return rv;
> }
>
> +static unsigned int s3c24x0_i2c_set_bus_speed(struct i2c_adapter *adap,
> + unsigned int speed)
> +{
> + struct s3c24x0_i2c_bus *i2c_bus;
> +
> + i2c_bus = get_bus(adap->hwadapnr);
> + if (!i2c_bus)
> + return -1;
> +
> + i2c_bus->clock_frequency = speed;
> +
> + if (i2c_bus->is_highspeed) {
> + if (hsi2c_get_clk_details(i2c_bus))
> + return -1;
> + hsi2c_ch_init(i2c_bus);
> + } else {
> + i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE);
> + }
> +
> + return 0;
> +}
> +
> /*
> * cmd_type is 0 for write, 1 for read.
> *
> @@ -840,13 +831,13 @@ bailout:
> return result;
> }
>
> -int i2c_probe(uchar chip)
> +static int s3c24x0_i2c_probe(struct i2c_adapter *adap, uchar chip)
> {
> struct s3c24x0_i2c_bus *i2c_bus;
> uchar buf[1];
> int ret;
>
> - i2c_bus = get_bus(g_current_bus);
> + i2c_bus = get_bus(adap->hwadapnr);
> if (!i2c_bus)
> return -1;
> buf[0] = 0;
> @@ -864,11 +855,11 @@ int i2c_probe(uchar chip)
> I2C_READ, chip << 1, 0, 0, buf, 1);
> }
>
> -
> return ret != I2C_OK;
> }
>
> -int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
> +static int s3c24x0_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
> + int alen, uchar *buffer, int len)
> {
> struct s3c24x0_i2c_bus *i2c_bus;
> uchar xaddr[4];
> @@ -902,7 +893,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
> chip |= ((addr >> (alen * 8)) &
> CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
> #endif
> - i2c_bus = get_bus(g_current_bus);
> + i2c_bus = get_bus(adap->hwadapnr);
> if (!i2c_bus)
> return -1;
>
> @@ -922,7 +913,8 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
> return 0;
> }
>
> -int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
> +static int s3c24x0_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
> + int alen, uchar *buffer, int len)
> {
> struct s3c24x0_i2c_bus *i2c_bus;
> uchar xaddr[4];
> @@ -955,7 +947,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
> chip |= ((addr >> (alen * 8)) &
> CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
> #endif
> - i2c_bus = get_bus(g_current_bus);
> + i2c_bus = get_bus(adap->hwadapnr);
> if (!i2c_bus)
> return -1;
>
> @@ -1001,8 +993,8 @@ static void process_nodes(const void *blob, int node_list[], int count,
>
> bus->id = pinmux_decode_periph_id(blob, node);
> bus->clock_frequency = fdtdec_get_int(blob, node,
> - "clock-frequency",
> - CONFIG_SYS_I2C_SPEED);
> + "clock-frequency",
> + CONFIG_SYS_I2C_S3C24X0_SPEED);
> bus->node = node;
> bus->bus_num = i;
> exynos_pinmux_config(bus->id, 0);
> @@ -1044,7 +1036,6 @@ int i2c_get_bus_num_fdt(int node)
> return -1;
> }
>
> -#ifdef CONFIG_I2C_MULTI_BUS
> int i2c_reset_port_fdt(const void *blob, int node)
> {
> struct s3c24x0_i2c_bus *i2c_bus;
> @@ -1068,12 +1059,61 @@ int i2c_reset_port_fdt(const void *blob, int node)
> hsi2c_ch_init(i2c_bus);
> } else {
> i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency,
> - CONFIG_SYS_I2C_SLAVE);
> + CONFIG_SYS_I2C_S3C24X0_SLAVE);
> }
>
> return 0;
> }
> #endif
> -#endif
>
> -#endif /* CONFIG_HARD_I2C */
> +/*
> + * Register s3c24x0 i2c adapters
> + */
> +U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_0, s3c24x0_i2c_init, s3c24x0_i2c_probe,
> + s3c24x0_i2c_read, s3c24x0_i2c_write,
> + s3c24x0_i2c_set_bus_speed,
> + CONFIG_SYS_I2C_S3C24X0_SPEED,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE,
> + 0)
> +U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_1, s3c24x0_i2c_init, s3c24x0_i2c_probe,
> + s3c24x0_i2c_read, s3c24x0_i2c_write,
> + s3c24x0_i2c_set_bus_speed,
> + CONFIG_SYS_I2C_S3C24X0_SPEED,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE,
> + 1)
> +U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_2, s3c24x0_i2c_init, s3c24x0_i2c_probe,
> + s3c24x0_i2c_read, s3c24x0_i2c_write,
> + s3c24x0_i2c_set_bus_speed,
> + CONFIG_SYS_I2C_S3C24X0_SPEED,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE,
> + 2)
> +U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_3, s3c24x0_i2c_init, s3c24x0_i2c_probe,
> + s3c24x0_i2c_read, s3c24x0_i2c_write,
> + s3c24x0_i2c_set_bus_speed,
> + CONFIG_SYS_I2C_S3C24X0_SPEED,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE,
> + 3)
> +U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_4, s3c24x0_i2c_init, s3c24x0_i2c_probe,
> + s3c24x0_i2c_read, s3c24x0_i2c_write,
> + s3c24x0_i2c_set_bus_speed,
> + CONFIG_SYS_I2C_S3C24X0_SPEED,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE,
> + 4)
> +U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_5, s3c24x0_i2c_init, s3c24x0_i2c_probe,
> + s3c24x0_i2c_read, s3c24x0_i2c_write,
> + s3c24x0_i2c_set_bus_speed,
> + CONFIG_SYS_I2C_S3C24X0_SPEED,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE,
> + 5)
> +U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_6, s3c24x0_i2c_init, s3c24x0_i2c_probe,
> + s3c24x0_i2c_read, s3c24x0_i2c_write,
> + s3c24x0_i2c_set_bus_speed,
> + CONFIG_SYS_I2C_S3C24X0_SPEED,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE,
> + 6)
> +U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_7, s3c24x0_i2c_init, s3c24x0_i2c_probe,
> + s3c24x0_i2c_read, s3c24x0_i2c_write,
> + s3c24x0_i2c_set_bus_speed,
> + CONFIG_SYS_I2C_S3C24X0_SPEED,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE,
> + 7)
> diff --git a/include/configs/VCMA9.h b/include/configs/VCMA9.h
> index 79a6079..57b620d 100644
> --- a/include/configs/VCMA9.h
> +++ b/include/configs/VCMA9.h
> @@ -73,12 +73,12 @@
> * the MPL VCMA9 is equipped with an ATMEL 24C256 EEPROM at
> * address 0x50 with 16bit addressing
> */
> -#define CONFIG_HARD_I2C /* I2C with hardware support */
> -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */
> -#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave addr */
> +#define CONFIG_SYS_I2C
>
> /* we use the built-in I2C controller */
> -#define CONFIG_DRIVER_S3C24X0_I2C
> +#define CONFIG_SYS_I2C_S3C24X0
> +#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* I2C speed */
> +#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x7F /* I2C slave addr */
>
> #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
> #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
> diff --git a/include/configs/arndale.h b/include/configs/arndale.h
> index 45fa047..ea8753b 100644
> --- a/include/configs/arndale.h
> +++ b/include/configs/arndale.h
> @@ -214,13 +214,12 @@
>
> /* I2C */
> #define CONFIG_SYS_I2C_INIT_BOARD
> -#define CONFIG_HARD_I2C
> +#define CONFIG_SYS_I2C
> #define CONFIG_CMD_I2C
> -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 Kbps */
> -#define CONFIG_DRIVER_S3C24X0_I2C
> -#define CONFIG_I2C_MULTI_BUS
> +#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* 100 Kbps */
> +#define CONFIG_SYS_I2C_S3C24X0
> #define CONFIG_MAX_I2C_NUM 8
> -#define CONFIG_SYS_I2C_SLAVE 0x0
> +#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x0
> #define CONFIG_I2C_EDID
>
> /* PMIC */
> diff --git a/include/configs/exynos5250-dt.h b/include/configs/exynos5250-dt.h
> index bdefee1..0155322 100644
> --- a/include/configs/exynos5250-dt.h
> +++ b/include/configs/exynos5250-dt.h
> @@ -249,13 +249,13 @@
>
> /* I2C */
> #define CONFIG_SYS_I2C_INIT_BOARD
> -#define CONFIG_HARD_I2C
> +#define CONFIG_SYS_I2C
> #define CONFIG_CMD_I2C
> -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 Kbps */
> -#define CONFIG_DRIVER_S3C24X0_I2C
> +#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* 100 Kbps */
> +#define CONFIG_SYS_I2C_S3C24X0
> #define CONFIG_I2C_MULTI_BUS
> #define CONFIG_MAX_I2C_NUM 8
> -#define CONFIG_SYS_I2C_SLAVE 0x0
> +#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x0
> #define CONFIG_I2C_EDID
>
> /* PMIC */
> diff --git a/include/configs/trats.h b/include/configs/trats.h
> index 3d080c4..f163303 100644
> --- a/include/configs/trats.h
> +++ b/include/configs/trats.h
> @@ -16,6 +16,7 @@
> */
> #define CONFIG_SAMSUNG /* in a SAMSUNG core */
> #define CONFIG_S5P /* which is in a S5P Family */
> +#define CONFIG_EXYNOS4 /* which is in a EXYNOS4XXX */
> #define CONFIG_EXYNOS4210 /* which is in a EXYNOS4210 */
> #define CONFIG_TRATS /* working with TRATS */
> #define CONFIG_TIZEN /* TIZEN lib */
> @@ -268,31 +269,21 @@
> #define CONFIG_SYS_CACHELINE_SIZE 32
>
> #define CONFIG_SYS_I2C
> +#define CONFIG_SYS_I2C_S3C24X0
> +#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000
> +#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0xFE
> +#define CONFIG_MAX_I2C_NUM 8
> #define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
> #define CONFIG_SYS_I2C_SOFT_SPEED 50000
> -#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
> -#define I2C_SOFT_DECLARATIONS2
> -#define CONFIG_SYS_I2C_SOFT_SPEED_2 50000
> -#define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F
> +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F
> #define CONFIG_SOFT_I2C_READ_REPEATED_START
> #define CONFIG_SYS_I2C_INIT_BOARD
> -#define CONFIG_I2C_MULTI_BUS
> -#define CONFIG_SOFT_I2C_MULTI_BUS
> -#define CONFIG_SYS_MAX_I2C_BUS 15
>
> #include <asm/arch/gpio.h>
>
> -/* I2C PMIC */
> -#define CONFIG_SOFT_I2C_I2C5_SCL exynos4_gpio_part1_get_nr(b, 7)
> -#define CONFIG_SOFT_I2C_I2C5_SDA exynos4_gpio_part1_get_nr(b, 6)
> -
> /* I2C FG */
> -#define CONFIG_SOFT_I2C_I2C9_SCL exynos4_gpio_part2_get_nr(y4, 1)
> -#define CONFIG_SOFT_I2C_I2C9_SDA exynos4_gpio_part2_get_nr(y4, 0)
> -
> -#define CONFIG_SOFT_I2C_GPIO_SCL get_multi_scl_pin()
> -#define CONFIG_SOFT_I2C_GPIO_SDA get_multi_sda_pin()
> -#define I2C_INIT multi_i2c_init()
> +#define CONFIG_SOFT_I2C_GPIO_SCL exynos4_gpio_part2_get_nr(y4, 1)
> +#define CONFIG_SOFT_I2C_GPIO_SDA exynos4_gpio_part2_get_nr(y4, 0)
>
> #define CONFIG_POWER
> #define CONFIG_POWER_I2C
> diff --git a/include/configs/trats2.h b/include/configs/trats2.h
> index 0e93836..3bcdfb1 100644
> --- a/include/configs/trats2.h
> +++ b/include/configs/trats2.h
> @@ -260,30 +260,25 @@
> #include <asm/arch/gpio.h>
>
> #define CONFIG_SYS_I2C
> -#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
> +#define CONFIG_SYS_I2C_S3C24X0
> +#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000
> +#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0
> +#define CONFIG_MAX_I2C_NUM 8
> +#define CONFIG_SYS_I2C_SOFT
> #define CONFIG_SYS_I2C_SOFT_SPEED 50000
> #define CONFIG_SYS_I2C_SOFT_SLAVE 0x00
> #define I2C_SOFT_DECLARATIONS2
> #define CONFIG_SYS_I2C_SOFT_SPEED_2 50000
> #define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x00
> -#define I2C_SOFT_DECLARATIONS3
> -#define CONFIG_SYS_I2C_SOFT_SPEED_3 50000
> -#define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x00
> #define CONFIG_SOFT_I2C_READ_REPEATED_START
> #define CONFIG_SYS_I2C_INIT_BOARD
> -#define CONFIG_I2C_MULTI_BUS
> -#define CONFIG_SOFT_I2C_MULTI_BUS
> -#define CONFIG_SYS_MAX_I2C_BUS 15
> -
> -#define CONFIG_SOFT_I2C_I2C5_SCL exynos4x12_gpio_part1_get_nr(d0, 3)
> -#define CONFIG_SOFT_I2C_I2C5_SDA exynos4x12_gpio_part1_get_nr(d0, 2)
> -#define CONFIG_SOFT_I2C_I2C9_SCL exynos4x12_gpio_part1_get_nr(f1, 4)
> -#define CONFIG_SOFT_I2C_I2C9_SDA exynos4x12_gpio_part1_get_nr(f1, 5)
> -#define CONFIG_SOFT_I2C_I2C10_SCL exynos4x12_gpio_part2_get_nr(m2, 1)
> -#define CONFIG_SOFT_I2C_I2C10_SDA exynos4x12_gpio_part2_get_nr(m2, 0)
> -#define CONFIG_SOFT_I2C_GPIO_SCL get_multi_scl_pin()
> -#define CONFIG_SOFT_I2C_GPIO_SDA get_multi_sda_pin()
> -#define I2C_INIT multi_i2c_init()
> +
> +#ifndef __ASSEMBLY__
> +int get_soft_i2c_scl_pin(void);
> +int get_soft_i2c_sda_pin(void);
> +#endif
> +#define CONFIG_SOFT_I2C_GPIO_SCL get_soft_i2c_scl_pin()
> +#define CONFIG_SOFT_I2C_GPIO_SDA get_soft_i2c_sda_pin()
>
> /* POWER */
> #define CONFIG_POWER
> --
> 1.7.9.5
Logically from s3c24x0_i2c.c driver point of view, this is much
similar to the code
submitted earlier at
http://lists.denx.de/pipermail/u-boot/2013-October/164821.html
However, i would make slight changes and test the same on Exynos5420/SMDK5420
Will post the changes separately.
>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
--
Shine bright,
(: Nav :)
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH V2 1/2] driver:i2c:s3c24x0: adapt driver to new i2c
2013-11-20 9:43 ` [U-Boot] [PATCH V2 1/2] driver:i2c:s3c24x0: adapt driver to new i2c Piotr Wilczek
2013-11-20 9:43 ` [U-Boot] [PATCH 2/2] driver:i2c:s3c24x0: fix clock init for hsi2c Piotr Wilczek
2013-11-20 12:08 ` [U-Boot] [PATCH V2 1/2] driver:i2c:s3c24x0: adapt driver to new i2c Naveen Krishna Ch
@ 2013-11-20 14:15 ` Naveen Krishna Ch
2013-11-21 4:28 ` Heiko Schocher
2013-12-09 6:50 ` [U-Boot] [U-Boot, V2, " Heiko Schocher
3 siblings, 1 reply; 17+ messages in thread
From: Naveen Krishna Ch @ 2013-11-20 14:15 UTC (permalink / raw)
To: u-boot
Hello All,
On 20 November 2013 15:13, Piotr Wilczek <p.wilczek@samsung.com> wrote:
> This patch adapts the s3c24x0 driver to the new i2c framework.
> Config file is modified for all the boards that use the driver.
>
> Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> CC: Minkyu Kang <mk7.kang@samsung.com>
> CC: Heiko Schocher <hs@denx.de>
> CC: Inderpal Singh <inderpal.singh@linaro.org>
> CC: David M?ller <d.mueller@elsoft.ch>
> CC: Chander Kashyap <k.chander@samsung.com>
> CC: Lukasz Majewski <l.majewski@samsung.com>
Tested on SMDK5420 with slight changes, will post separately
Tested-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Changes look neat
Reviewed-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
> ---
> Boards VCMA9, Arndale and Exynos5250 are compile tested only.
> Boards Trats and Trats2 were hardware tested.
> All boards compile clean.
>
> Changes for V2:
> - patch series squashed to one patch
> - removed unnecessary blank line
> - change related to hsi2c moved to saparate patch
>
> board/samsung/smdk5250/exynos5-dt.c | 2 -
> board/samsung/trats/trats.c | 21 ++---
> board/samsung/trats2/trats2.c | 35 ++++++--
> drivers/i2c/Makefile | 2 +-
> drivers/i2c/s3c24x0_i2c.c | 152 ++++++++++++++++++++++-------------
> include/configs/VCMA9.h | 8 +-
> include/configs/arndale.h | 9 +--
> include/configs/exynos5250-dt.h | 8 +-
> include/configs/trats.h | 25 ++----
> include/configs/trats2.h | 29 +++----
> 10 files changed, 170 insertions(+), 121 deletions(-)
>
> diff --git a/board/samsung/smdk5250/exynos5-dt.c b/board/samsung/smdk5250/exynos5-dt.c
> index 6bcc883..6aa0509 100644
> --- a/board/samsung/smdk5250/exynos5-dt.c
> +++ b/board/samsung/smdk5250/exynos5-dt.c
> @@ -150,8 +150,6 @@ int power_init_board(void)
>
> set_ps_hold_ctrl();
>
> - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
> -
> if (pmic_init(I2C_PMIC))
> return -1;
>
> diff --git a/board/samsung/trats/trats.c b/board/samsung/trats/trats.c
> index 7012c13..44be5fc 100644
> --- a/board/samsung/trats/trats.c
> +++ b/board/samsung/trats/trats.c
> @@ -57,15 +57,18 @@ int board_init(void)
>
> void i2c_init_board(void)
> {
> - struct exynos4_gpio_part1 *gpio1 =
> - (struct exynos4_gpio_part1 *)samsung_get_base_gpio_part1();
> + int err;
> struct exynos4_gpio_part2 *gpio2 =
> (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2();
>
> - /* I2C_5 -> PMIC -> Adapter 0 */
> - s5p_gpio_direction_output(&gpio1->b, 7, 1);
> - s5p_gpio_direction_output(&gpio1->b, 6, 1);
> - /* I2C_9 -> FG -> Adapter 1 */
> + /* I2C_5 -> PMIC */
> + err = exynos_pinmux_config(PERIPH_ID_I2C5, PINMUX_FLAG_NONE);
> + if (err) {
> + debug("I2C%d not configured\n", (I2C_5));
> + return;
> + }
> +
> + /* I2C_8 -> FG */
> s5p_gpio_direction_output(&gpio2->y4, 0, 1);
> s5p_gpio_direction_output(&gpio2->y4, 1, 1);
> }
> @@ -290,10 +293,10 @@ int power_init_board(void)
> * The FUEL_GAUGE is marked as I2C9 on the schematic, but connected
> * to logical I2C adapter 1
> */
> - ret = pmic_init(I2C_0);
> + ret = pmic_init(I2C_5);
> ret |= pmic_init_max8997();
> - ret |= power_fg_init(I2C_1);
> - ret |= power_muic_init(I2C_0);
> + ret |= power_fg_init(I2C_8);
> + ret |= power_muic_init(I2C_5);
> ret |= power_bat_init(0);
> if (ret)
> return ret;
> diff --git a/board/samsung/trats2/trats2.c b/board/samsung/trats2/trats2.c
> index d44d825..8df85ee 100644
> --- a/board/samsung/trats2/trats2.c
> +++ b/board/samsung/trats2/trats2.c
> @@ -115,12 +115,17 @@ static void board_external_gpio_init(void)
> #ifdef CONFIG_SYS_I2C_INIT_BOARD
> static void board_init_i2c(void)
> {
> + int err;
> +
> gpio1 = (struct exynos4x12_gpio_part1 *)EXYNOS4X12_GPIO_PART1_BASE;
> gpio2 = (struct exynos4x12_gpio_part2 *)EXYNOS4X12_GPIO_PART2_BASE;
>
> /* I2C_7 */
> - s5p_gpio_direction_output(&gpio1->d0, 2, 1);
> - s5p_gpio_direction_output(&gpio1->d0, 3, 1);
> + err = exynos_pinmux_config(PERIPH_ID_I2C7, PINMUX_FLAG_NONE);
> + if (err) {
> + debug("I2C%d not configured\n", (I2C_7));
> + return;
> + }
>
> /* I2C_8 */
> s5p_gpio_direction_output(&gpio1->f1, 4, 1);
> @@ -132,6 +137,24 @@ static void board_init_i2c(void)
> }
> #endif
>
> +#ifdef CONFIG_SYS_I2C_SOFT
> +int get_soft_i2c_scl_pin(void)
> +{
> + if (I2C_ADAP_HWNR)
> + return exynos4x12_gpio_part2_get_nr(m2, 1); /* I2C9 */
> + else
> + return exynos4x12_gpio_part1_get_nr(f1, 4); /* I2C8 */
> +}
> +
> +int get_soft_i2c_sda_pin(void)
> +{
> + if (I2C_ADAP_HWNR)
> + return exynos4x12_gpio_part2_get_nr(m2, 0); /* I2C9 */
> + else
> + return exynos4x12_gpio_part1_get_nr(f1, 5); /* I2C8 */
> +}
> +#endif
> +
> int board_early_init_f(void)
> {
> check_hw_revision();
> @@ -167,11 +190,11 @@ int power_init_board(void)
> #ifdef CONFIG_SYS_I2C_INIT_BOARD
> board_init_i2c();
> #endif
> - pmic_init(I2C_0); /* I2C adapter 0 - bus name I2C_5 */
> + pmic_init(I2C_7); /* I2C adapter 7 - bus name s3c24x0_7 */
> pmic_init_max77686();
> - pmic_init_max77693(I2C_2); /* I2C adapter 2 - bus name I2C_10 */
> - power_muic_init(I2C_2); /* I2C adapter 2 - bus name I2C_10 */
> - power_fg_init(I2C_1); /* I2C adapter 1 - bus name I2C_9 */
> + pmic_init_max77693(I2C_9); /* I2C adapter 9 - bus name soft1 */
> + power_muic_init(I2C_9); /* I2C adapter 9 - bus name soft1 */
> + power_fg_init(I2C_8); /* I2C adapter 8 - bus name soft0 */
> power_bat_init(0);
>
> p_chrg = pmic_get("MAX77693_PMIC");
> diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
> index 553b519..fa3a875 100644
> --- a/drivers/i2c/Makefile
> +++ b/drivers/i2c/Makefile
> @@ -12,7 +12,6 @@ obj-$(CONFIG_I2C_MVTWSI) += mvtwsi.o
> obj-$(CONFIG_I2C_MV) += mv_i2c.o
> obj-$(CONFIG_I2C_MXS) += mxs_i2c.o
> obj-$(CONFIG_PCA9564_I2C) += pca9564_i2c.o
> -obj-$(CONFIG_DRIVER_S3C24X0_I2C) += s3c24x0_i2c.o
> obj-$(CONFIG_TSI108_I2C) += tsi108_i2c.o
> obj-$(CONFIG_U8500_I2C) += u8500_i2c.o
> obj-$(CONFIG_SH_SH7734_I2C) += sh_sh7734_i2c.o
> @@ -24,6 +23,7 @@ obj-$(CONFIG_SYS_I2C_OMAP24XX) += omap24xx_i2c.o
> obj-$(CONFIG_SYS_I2C_OMAP34XX) += omap24xx_i2c.o
> obj-$(CONFIG_SYS_I2C_PPC4XX) += ppc4xx_i2c.o
> obj-$(CONFIG_SYS_I2C_RCAR) += rcar_i2c.o
> +obj-$(CONFIG_SYS_I2C_S3C24X0) += s3c24x0_i2c.o
> obj-$(CONFIG_SYS_I2C_SH) += sh_i2c.o
> obj-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o
> obj-$(CONFIG_SYS_I2C_TEGRA) += tegra_i2c.o
> diff --git a/drivers/i2c/s3c24x0_i2c.c b/drivers/i2c/s3c24x0_i2c.c
> index f77a9d1..5dc35e7 100644
> --- a/drivers/i2c/s3c24x0_i2c.c
> +++ b/drivers/i2c/s3c24x0_i2c.c
> @@ -23,8 +23,6 @@
> #include <i2c.h>
> #include "s3c24x0_i2c.h"
>
> -#ifdef CONFIG_HARD_I2C
> -
> #define I2C_WRITE 0
> #define I2C_READ 1
>
> @@ -127,7 +125,6 @@
> * For SPL boot some boards need i2c before SDRAM is initialised so force
> * variables to live in SRAM
> */
> -static unsigned int g_current_bus __attribute__((section(".data")));
> static struct s3c24x0_i2c_bus i2c_bus[CONFIG_MAX_I2C_NUM]
> __attribute__((section(".data")));
>
> @@ -254,17 +251,17 @@ static void ReadWriteByte(struct s3c24x0_i2c *i2c)
> writel(readl(&i2c->iiccon) & ~I2CCON_IRPND, &i2c->iiccon);
> }
>
> -static struct s3c24x0_i2c *get_base_i2c(void)
> +static struct s3c24x0_i2c *get_base_i2c(int bus)
> {
> #ifdef CONFIG_EXYNOS4
> struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c *)(samsung_get_base_i2c()
> + (EXYNOS4_I2C_SPACING
> - * g_current_bus));
> + * bus));
> return i2c;
> #elif defined CONFIG_EXYNOS5
> struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c *)(samsung_get_base_i2c()
> + (EXYNOS5_I2C_SPACING
> - * g_current_bus));
> + * bus));
> return i2c;
> #else
> return s3c24x0_get_base_i2c();
> @@ -298,7 +295,6 @@ static void i2c_ch_init(struct s3c24x0_i2c *i2c, int speed, int slaveadd)
> writel(I2C_MODE_MT | I2C_TXRX_ENA, &i2c->iicstat);
> }
>
> -#ifdef CONFIG_I2C_MULTI_BUS
> static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
> {
> struct exynos5_hsi2c *hsregs = i2c_bus->hsregs;
> @@ -330,7 +326,6 @@ static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
> }
> return -1;
> }
> -#endif
>
> static void hsi2c_ch_init(struct s3c24x0_i2c_bus *i2c_bus)
> {
> @@ -401,49 +396,18 @@ static void exynos5_i2c_reset(struct s3c24x0_i2c_bus *i2c_bus)
> hsi2c_ch_init(i2c_bus);
> }
>
> -/*
> - * MULTI BUS I2C support
> - */
> -
> -#ifdef CONFIG_I2C_MULTI_BUS
> -int i2c_set_bus_num(unsigned int bus)
> -{
> - struct s3c24x0_i2c_bus *i2c_bus;
> -
> - i2c_bus = get_bus(bus);
> - if (!i2c_bus)
> - return -1;
> - g_current_bus = bus;
> -
> - if (i2c_bus->is_highspeed) {
> - if (hsi2c_get_clk_details(i2c_bus))
> - return -1;
> - hsi2c_ch_init(i2c_bus);
> - } else {
> - i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency,
> - CONFIG_SYS_I2C_SLAVE);
> - }
> -
> - return 0;
> -}
> -
> -unsigned int i2c_get_bus_num(void)
> -{
> - return g_current_bus;
> -}
> -#endif
> -
> -void i2c_init(int speed, int slaveadd)
> +static void s3c24x0_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd)
> {
> struct s3c24x0_i2c *i2c;
> + struct s3c24x0_i2c_bus *bus;
> +
> #if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5)
> struct s3c24x0_gpio *gpio = s3c24x0_get_base_gpio();
> #endif
> ulong start_time = get_timer(0);
>
> /* By default i2c channel 0 is the current bus */
> - g_current_bus = 0;
> - i2c = get_base_i2c();
> + i2c = get_base_i2c(adap->hwadapnr);
>
> /*
> * In case the previous transfer is still going, wait to give it a
> @@ -505,6 +469,10 @@ void i2c_init(int speed, int slaveadd)
> }
> #endif /* #if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5) */
> i2c_ch_init(i2c, speed, slaveadd);
> +
> + bus = &i2c_bus[adap->hwadapnr];
> + bus->active = true;
> + bus->regs = i2c;
> }
>
> /*
> @@ -728,6 +696,29 @@ static int hsi2c_read(struct exynos5_hsi2c *i2c,
> return rv;
> }
>
> +static unsigned int s3c24x0_i2c_set_bus_speed(struct i2c_adapter *adap,
> + unsigned int speed)
> +{
> + struct s3c24x0_i2c_bus *i2c_bus;
> +
> + i2c_bus = get_bus(adap->hwadapnr);
> + if (!i2c_bus)
> + return -1;
> +
> + i2c_bus->clock_frequency = speed;
> +
> + if (i2c_bus->is_highspeed) {
> + if (hsi2c_get_clk_details(i2c_bus))
> + return -1;
> + hsi2c_ch_init(i2c_bus);
> + } else {
> + i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE);
> + }
> +
> + return 0;
> +}
> +
> /*
> * cmd_type is 0 for write, 1 for read.
> *
> @@ -840,13 +831,13 @@ bailout:
> return result;
> }
>
> -int i2c_probe(uchar chip)
> +static int s3c24x0_i2c_probe(struct i2c_adapter *adap, uchar chip)
> {
> struct s3c24x0_i2c_bus *i2c_bus;
> uchar buf[1];
> int ret;
>
> - i2c_bus = get_bus(g_current_bus);
> + i2c_bus = get_bus(adap->hwadapnr);
> if (!i2c_bus)
> return -1;
> buf[0] = 0;
> @@ -864,11 +855,11 @@ int i2c_probe(uchar chip)
> I2C_READ, chip << 1, 0, 0, buf, 1);
> }
>
> -
> return ret != I2C_OK;
> }
>
> -int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
> +static int s3c24x0_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
> + int alen, uchar *buffer, int len)
> {
> struct s3c24x0_i2c_bus *i2c_bus;
> uchar xaddr[4];
> @@ -902,7 +893,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
> chip |= ((addr >> (alen * 8)) &
> CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
> #endif
> - i2c_bus = get_bus(g_current_bus);
> + i2c_bus = get_bus(adap->hwadapnr);
> if (!i2c_bus)
> return -1;
>
> @@ -922,7 +913,8 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
> return 0;
> }
>
> -int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
> +static int s3c24x0_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
> + int alen, uchar *buffer, int len)
> {
> struct s3c24x0_i2c_bus *i2c_bus;
> uchar xaddr[4];
> @@ -955,7 +947,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
> chip |= ((addr >> (alen * 8)) &
> CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
> #endif
> - i2c_bus = get_bus(g_current_bus);
> + i2c_bus = get_bus(adap->hwadapnr);
> if (!i2c_bus)
> return -1;
>
> @@ -1001,8 +993,8 @@ static void process_nodes(const void *blob, int node_list[], int count,
>
> bus->id = pinmux_decode_periph_id(blob, node);
> bus->clock_frequency = fdtdec_get_int(blob, node,
> - "clock-frequency",
> - CONFIG_SYS_I2C_SPEED);
> + "clock-frequency",
> + CONFIG_SYS_I2C_S3C24X0_SPEED);
> bus->node = node;
> bus->bus_num = i;
> exynos_pinmux_config(bus->id, 0);
> @@ -1044,7 +1036,6 @@ int i2c_get_bus_num_fdt(int node)
> return -1;
> }
>
> -#ifdef CONFIG_I2C_MULTI_BUS
> int i2c_reset_port_fdt(const void *blob, int node)
> {
> struct s3c24x0_i2c_bus *i2c_bus;
> @@ -1068,12 +1059,61 @@ int i2c_reset_port_fdt(const void *blob, int node)
> hsi2c_ch_init(i2c_bus);
> } else {
> i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency,
> - CONFIG_SYS_I2C_SLAVE);
> + CONFIG_SYS_I2C_S3C24X0_SLAVE);
> }
>
> return 0;
> }
> #endif
> -#endif
>
> -#endif /* CONFIG_HARD_I2C */
> +/*
> + * Register s3c24x0 i2c adapters
> + */
> +U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_0, s3c24x0_i2c_init, s3c24x0_i2c_probe,
> + s3c24x0_i2c_read, s3c24x0_i2c_write,
> + s3c24x0_i2c_set_bus_speed,
> + CONFIG_SYS_I2C_S3C24X0_SPEED,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE,
> + 0)
> +U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_1, s3c24x0_i2c_init, s3c24x0_i2c_probe,
> + s3c24x0_i2c_read, s3c24x0_i2c_write,
> + s3c24x0_i2c_set_bus_speed,
> + CONFIG_SYS_I2C_S3C24X0_SPEED,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE,
> + 1)
> +U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_2, s3c24x0_i2c_init, s3c24x0_i2c_probe,
> + s3c24x0_i2c_read, s3c24x0_i2c_write,
> + s3c24x0_i2c_set_bus_speed,
> + CONFIG_SYS_I2C_S3C24X0_SPEED,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE,
> + 2)
> +U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_3, s3c24x0_i2c_init, s3c24x0_i2c_probe,
> + s3c24x0_i2c_read, s3c24x0_i2c_write,
> + s3c24x0_i2c_set_bus_speed,
> + CONFIG_SYS_I2C_S3C24X0_SPEED,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE,
> + 3)
> +U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_4, s3c24x0_i2c_init, s3c24x0_i2c_probe,
> + s3c24x0_i2c_read, s3c24x0_i2c_write,
> + s3c24x0_i2c_set_bus_speed,
> + CONFIG_SYS_I2C_S3C24X0_SPEED,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE,
> + 4)
> +U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_5, s3c24x0_i2c_init, s3c24x0_i2c_probe,
> + s3c24x0_i2c_read, s3c24x0_i2c_write,
> + s3c24x0_i2c_set_bus_speed,
> + CONFIG_SYS_I2C_S3C24X0_SPEED,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE,
> + 5)
> +U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_6, s3c24x0_i2c_init, s3c24x0_i2c_probe,
> + s3c24x0_i2c_read, s3c24x0_i2c_write,
> + s3c24x0_i2c_set_bus_speed,
> + CONFIG_SYS_I2C_S3C24X0_SPEED,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE,
> + 6)
> +U_BOOT_I2C_ADAP_COMPLETE(s3c24x0_7, s3c24x0_i2c_init, s3c24x0_i2c_probe,
> + s3c24x0_i2c_read, s3c24x0_i2c_write,
> + s3c24x0_i2c_set_bus_speed,
> + CONFIG_SYS_I2C_S3C24X0_SPEED,
> + CONFIG_SYS_I2C_S3C24X0_SLAVE,
> + 7)
> diff --git a/include/configs/VCMA9.h b/include/configs/VCMA9.h
> index 79a6079..57b620d 100644
> --- a/include/configs/VCMA9.h
> +++ b/include/configs/VCMA9.h
> @@ -73,12 +73,12 @@
> * the MPL VCMA9 is equipped with an ATMEL 24C256 EEPROM at
> * address 0x50 with 16bit addressing
> */
> -#define CONFIG_HARD_I2C /* I2C with hardware support */
> -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */
> -#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave addr */
> +#define CONFIG_SYS_I2C
>
> /* we use the built-in I2C controller */
> -#define CONFIG_DRIVER_S3C24X0_I2C
> +#define CONFIG_SYS_I2C_S3C24X0
> +#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* I2C speed */
> +#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x7F /* I2C slave addr */
>
> #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
> #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
> diff --git a/include/configs/arndale.h b/include/configs/arndale.h
> index 45fa047..ea8753b 100644
> --- a/include/configs/arndale.h
> +++ b/include/configs/arndale.h
> @@ -214,13 +214,12 @@
>
> /* I2C */
> #define CONFIG_SYS_I2C_INIT_BOARD
> -#define CONFIG_HARD_I2C
> +#define CONFIG_SYS_I2C
> #define CONFIG_CMD_I2C
> -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 Kbps */
> -#define CONFIG_DRIVER_S3C24X0_I2C
> -#define CONFIG_I2C_MULTI_BUS
> +#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* 100 Kbps */
> +#define CONFIG_SYS_I2C_S3C24X0
> #define CONFIG_MAX_I2C_NUM 8
> -#define CONFIG_SYS_I2C_SLAVE 0x0
> +#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x0
> #define CONFIG_I2C_EDID
>
> /* PMIC */
> diff --git a/include/configs/exynos5250-dt.h b/include/configs/exynos5250-dt.h
> index bdefee1..0155322 100644
> --- a/include/configs/exynos5250-dt.h
> +++ b/include/configs/exynos5250-dt.h
> @@ -249,13 +249,13 @@
>
> /* I2C */
> #define CONFIG_SYS_I2C_INIT_BOARD
> -#define CONFIG_HARD_I2C
> +#define CONFIG_SYS_I2C
> #define CONFIG_CMD_I2C
> -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 Kbps */
> -#define CONFIG_DRIVER_S3C24X0_I2C
> +#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* 100 Kbps */
> +#define CONFIG_SYS_I2C_S3C24X0
> #define CONFIG_I2C_MULTI_BUS
> #define CONFIG_MAX_I2C_NUM 8
> -#define CONFIG_SYS_I2C_SLAVE 0x0
> +#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x0
> #define CONFIG_I2C_EDID
>
> /* PMIC */
> diff --git a/include/configs/trats.h b/include/configs/trats.h
> index 3d080c4..f163303 100644
> --- a/include/configs/trats.h
> +++ b/include/configs/trats.h
> @@ -16,6 +16,7 @@
> */
> #define CONFIG_SAMSUNG /* in a SAMSUNG core */
> #define CONFIG_S5P /* which is in a S5P Family */
> +#define CONFIG_EXYNOS4 /* which is in a EXYNOS4XXX */
> #define CONFIG_EXYNOS4210 /* which is in a EXYNOS4210 */
> #define CONFIG_TRATS /* working with TRATS */
> #define CONFIG_TIZEN /* TIZEN lib */
> @@ -268,31 +269,21 @@
> #define CONFIG_SYS_CACHELINE_SIZE 32
>
> #define CONFIG_SYS_I2C
> +#define CONFIG_SYS_I2C_S3C24X0
> +#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000
> +#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0xFE
> +#define CONFIG_MAX_I2C_NUM 8
> #define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
> #define CONFIG_SYS_I2C_SOFT_SPEED 50000
> -#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
> -#define I2C_SOFT_DECLARATIONS2
> -#define CONFIG_SYS_I2C_SOFT_SPEED_2 50000
> -#define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F
> +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F
> #define CONFIG_SOFT_I2C_READ_REPEATED_START
> #define CONFIG_SYS_I2C_INIT_BOARD
> -#define CONFIG_I2C_MULTI_BUS
> -#define CONFIG_SOFT_I2C_MULTI_BUS
> -#define CONFIG_SYS_MAX_I2C_BUS 15
>
> #include <asm/arch/gpio.h>
>
> -/* I2C PMIC */
> -#define CONFIG_SOFT_I2C_I2C5_SCL exynos4_gpio_part1_get_nr(b, 7)
> -#define CONFIG_SOFT_I2C_I2C5_SDA exynos4_gpio_part1_get_nr(b, 6)
> -
> /* I2C FG */
> -#define CONFIG_SOFT_I2C_I2C9_SCL exynos4_gpio_part2_get_nr(y4, 1)
> -#define CONFIG_SOFT_I2C_I2C9_SDA exynos4_gpio_part2_get_nr(y4, 0)
> -
> -#define CONFIG_SOFT_I2C_GPIO_SCL get_multi_scl_pin()
> -#define CONFIG_SOFT_I2C_GPIO_SDA get_multi_sda_pin()
> -#define I2C_INIT multi_i2c_init()
> +#define CONFIG_SOFT_I2C_GPIO_SCL exynos4_gpio_part2_get_nr(y4, 1)
> +#define CONFIG_SOFT_I2C_GPIO_SDA exynos4_gpio_part2_get_nr(y4, 0)
>
> #define CONFIG_POWER
> #define CONFIG_POWER_I2C
> diff --git a/include/configs/trats2.h b/include/configs/trats2.h
> index 0e93836..3bcdfb1 100644
> --- a/include/configs/trats2.h
> +++ b/include/configs/trats2.h
> @@ -260,30 +260,25 @@
> #include <asm/arch/gpio.h>
>
> #define CONFIG_SYS_I2C
> -#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
> +#define CONFIG_SYS_I2C_S3C24X0
> +#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000
> +#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0
> +#define CONFIG_MAX_I2C_NUM 8
> +#define CONFIG_SYS_I2C_SOFT
> #define CONFIG_SYS_I2C_SOFT_SPEED 50000
> #define CONFIG_SYS_I2C_SOFT_SLAVE 0x00
> #define I2C_SOFT_DECLARATIONS2
> #define CONFIG_SYS_I2C_SOFT_SPEED_2 50000
> #define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x00
> -#define I2C_SOFT_DECLARATIONS3
> -#define CONFIG_SYS_I2C_SOFT_SPEED_3 50000
> -#define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x00
> #define CONFIG_SOFT_I2C_READ_REPEATED_START
> #define CONFIG_SYS_I2C_INIT_BOARD
> -#define CONFIG_I2C_MULTI_BUS
> -#define CONFIG_SOFT_I2C_MULTI_BUS
> -#define CONFIG_SYS_MAX_I2C_BUS 15
> -
> -#define CONFIG_SOFT_I2C_I2C5_SCL exynos4x12_gpio_part1_get_nr(d0, 3)
> -#define CONFIG_SOFT_I2C_I2C5_SDA exynos4x12_gpio_part1_get_nr(d0, 2)
> -#define CONFIG_SOFT_I2C_I2C9_SCL exynos4x12_gpio_part1_get_nr(f1, 4)
> -#define CONFIG_SOFT_I2C_I2C9_SDA exynos4x12_gpio_part1_get_nr(f1, 5)
> -#define CONFIG_SOFT_I2C_I2C10_SCL exynos4x12_gpio_part2_get_nr(m2, 1)
> -#define CONFIG_SOFT_I2C_I2C10_SDA exynos4x12_gpio_part2_get_nr(m2, 0)
> -#define CONFIG_SOFT_I2C_GPIO_SCL get_multi_scl_pin()
> -#define CONFIG_SOFT_I2C_GPIO_SDA get_multi_sda_pin()
> -#define I2C_INIT multi_i2c_init()
> +
> +#ifndef __ASSEMBLY__
> +int get_soft_i2c_scl_pin(void);
> +int get_soft_i2c_sda_pin(void);
> +#endif
> +#define CONFIG_SOFT_I2C_GPIO_SCL get_soft_i2c_scl_pin()
> +#define CONFIG_SOFT_I2C_GPIO_SDA get_soft_i2c_sda_pin()
>
> /* POWER */
> #define CONFIG_POWER
> --
> 1.7.9.5
>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
--
Shine bright,
(: Nav :)
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH V2 1/2] driver:i2c:s3c24x0: adapt driver to new i2c
2013-11-20 14:15 ` Naveen Krishna Ch
@ 2013-11-21 4:28 ` Heiko Schocher
0 siblings, 0 replies; 17+ messages in thread
From: Heiko Schocher @ 2013-11-21 4:28 UTC (permalink / raw)
To: u-boot
Hello Naveen,
Am 20.11.2013 15:15, schrieb Naveen Krishna Ch:
> Hello All,
>
> On 20 November 2013 15:13, Piotr Wilczek<p.wilczek@samsung.com> wrote:
>> This patch adapts the s3c24x0 driver to the new i2c framework.
>> Config file is modified for all the boards that use the driver.
>>
>> Signed-off-by: Piotr Wilczek<p.wilczek@samsung.com>
>> Signed-off-by: Kyungmin Park<kyungmin.park@samsung.com>
>> CC: Minkyu Kang<mk7.kang@samsung.com>
>> CC: Heiko Schocher<hs@denx.de>
>> CC: Inderpal Singh<inderpal.singh@linaro.org>
>> CC: David M?ller<d.mueller@elsoft.ch>
>> CC: Chander Kashyap<k.chander@samsung.com>
>> CC: Lukasz Majewski<l.majewski@samsung.com>
> Tested on SMDK5420 with slight changes, will post separately
> Tested-by: Naveen Krishna Chatradhi<ch.naveen@samsung.com>
> Changes look neat
> Reviewed-by: Naveen Krishna Chatradhi<ch.naveen@samsung.com>
Thanks!
bye,
Heiko
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [U-Boot, V2, 1/2] driver:i2c:s3c24x0: adapt driver to new i2c
2013-11-20 9:43 ` [U-Boot] [PATCH V2 1/2] driver:i2c:s3c24x0: adapt driver to new i2c Piotr Wilczek
` (2 preceding siblings ...)
2013-11-20 14:15 ` Naveen Krishna Ch
@ 2013-12-09 6:50 ` Heiko Schocher
3 siblings, 0 replies; 17+ messages in thread
From: Heiko Schocher @ 2013-12-09 6:50 UTC (permalink / raw)
To: u-boot
Hello Piotr,
Am 20.11.2013 10:43, schrieb Piotr Wilczek:
> This patch adapts the s3c24x0 driver to the new i2c framework.
> Config file is modified for all the boards that use the driver.
>
> Signed-off-by: Piotr Wilczek<p.wilczek@samsung.com>
> Signed-off-by: Kyungmin Park<kyungmin.park@samsung.com>
> CC: Minkyu Kang<mk7.kang@samsung.com>
> CC: Heiko Schocher<hs@denx.de>
> CC: Inderpal Singh<inderpal.singh@linaro.org>
> CC: David M?ller<d.mueller@elsoft.ch>
> CC: Chander Kashyap<k.chander@samsung.com>
> CC: Lukasz Majewski<l.majewski@samsung.com>
> Tested-by: Naveen Krishna Chatradhi<ch.naveen@samsung.com>
> Reviewed-by: Naveen Krishna Chatradhi<ch.naveen@samsung.com>
>
> ---
> Boards VCMA9, Arndale and Exynos5250 are compile tested only.
> Boards Trats and Trats2 were hardware tested.
> All boards compile clean.
>
> Changes for V2:
> - patch series squashed to one patch
> - removed unnecessary blank line
> - change related to hsi2c moved to saparate patch
>
> board/samsung/smdk5250/exynos5-dt.c | 2 -
> board/samsung/trats/trats.c | 21 ++---
> board/samsung/trats2/trats2.c | 35 ++++++--
> drivers/i2c/Makefile | 2 +-
> drivers/i2c/s3c24x0_i2c.c | 152 ++++++++++++++++++++++-------------
> include/configs/VCMA9.h | 8 +-
> include/configs/arndale.h | 9 +--
> include/configs/exynos5250-dt.h | 8 +-
> include/configs/trats.h | 25 ++----
> include/configs/trats2.h | 29 +++----
> 10 files changed, 170 insertions(+), 121 deletions(-)
Thanks! Applied to u-boot-i2c.git
bye,
Heiko
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [U-Boot, 2/2] driver:i2c:s3c24x0: fix clock init for hsi2c
2013-11-20 9:43 ` [U-Boot] [PATCH 2/2] driver:i2c:s3c24x0: fix clock init for hsi2c Piotr Wilczek
@ 2013-12-09 6:50 ` Heiko Schocher
0 siblings, 0 replies; 17+ messages in thread
From: Heiko Schocher @ 2013-12-09 6:50 UTC (permalink / raw)
To: u-boot
Hello Piotr,
Am 20.11.2013 10:43, schrieb Piotr Wilczek:
> Fix clock value initialisation for Exynos other than Exynos5 for hsi2c.
>
> Signed-off-by: Piotr Wilczek<p.wilczek@samsung.com>
> Signed-off-by: Kyungmin Park<kyungmin.park@samsung.com>
> Cc: Minkyu Kang<mk7.kang@samsung.com>
> Cc: Heiko Schocher<hs@denx.de>
>
> ---
> drivers/i2c/s3c24x0_i2c.c | 4 +++-
> 1 file changed, 3 insertions(+), 1 deletion(-)
Thanks. Applied to u-boot-i2c.git
bye,
Heiko
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 17+ messages in thread
end of thread, other threads:[~2013-12-09 6:50 UTC | newest]
Thread overview: 17+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-11-13 14:31 [U-Boot] [PATCH 0/6] adapt s3c24x0 driver to new i2c framework Piotr Wilczek
2013-11-13 14:31 ` [U-Boot] [PATCH 1/6] driver:i2c:s3c24x0: adapt driver to new i2c Piotr Wilczek
2013-11-18 6:17 ` Heiko Schocher
2013-11-18 7:10 ` Piotr Wilczek
2013-11-18 7:19 ` Heiko Schocher
2013-11-13 14:31 ` [U-Boot] [PATCH 2/6] board:arndale: switch to new i2c framework Piotr Wilczek
2013-11-13 14:31 ` [U-Boot] [PATCH 3/6] board:VCMA9 " Piotr Wilczek
2013-11-13 14:31 ` [U-Boot] [PATCH 4/6] board:smdk5250: " Piotr Wilczek
2013-11-13 14:31 ` [U-Boot] [PATCH 5/6] board:trats: " Piotr Wilczek
2013-11-13 14:31 ` [U-Boot] [PATCH 6/6] board:trats2: switch Trats2 " Piotr Wilczek
2013-11-20 9:43 ` [U-Boot] [PATCH V2 1/2] driver:i2c:s3c24x0: adapt driver to new i2c Piotr Wilczek
2013-11-20 9:43 ` [U-Boot] [PATCH 2/2] driver:i2c:s3c24x0: fix clock init for hsi2c Piotr Wilczek
2013-12-09 6:50 ` [U-Boot] [U-Boot, " Heiko Schocher
2013-11-20 12:08 ` [U-Boot] [PATCH V2 1/2] driver:i2c:s3c24x0: adapt driver to new i2c Naveen Krishna Ch
2013-11-20 14:15 ` Naveen Krishna Ch
2013-11-21 4:28 ` Heiko Schocher
2013-12-09 6:50 ` [U-Boot] [U-Boot, V2, " Heiko Schocher
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.