* [PATCH v4 0/8] Device Tree support for the at91sam9261ek
@ 2014-02-12 10:06 ` Jean-Jacques Hiblot
0 siblings, 0 replies; 54+ messages in thread
From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw)
To: nicolas.ferre, plagnioj, b.brezillon
Cc: linux-kernel, linux-arm-kernel, gregory.clement, Jean-Jacques Hiblot
This patch set aims at bringing a device tree support for the sam9261.
It's mostly based on the sam9263 and sam9x5 stuff.
Changes since V3:
* Added support for the touchscreen
* Added support for the spi dataflash
* Activated the TCB by default
* Reworked the patch organization to reduce the number of patchs
* changed the default bootargs (no mem description, UBI on mtdpart 5)
* Changed the xlate implementation of the at91 pinctrl driver to lock the GPIOs
for IRQs instead of requesting them (needed for the touchscreen driver)
* some stylistic changes
Changes since V2:
* removed the smc driver from the serie. It'll be posted in an independent
serie later.
* removed the DM9000 support (it'll come with the smc driver)
* the sam9261 now supports the Common Clock Framework (CCF). Note: to enable
the CCF you must remove from the kernel config the platforms that don't
support it.
* Added basic DT binding for the bus matrix
* Added support for USB host
* Added support for USB gadget
* in dts(i), replaced interrupt-parent with interrupts-extended
* changed the nand partition plan (same as for the sama5d3)
* removed 'mem' parameter in command line
* re-ordered dt-nodes in ascending address order.
* split the lcd support patch in 2 parts (SOC and board)
Change since V1:
* changed the DT representation to use address translation and separate the
timings' configuration from the device properties by adding a "simple-bus"
inetrmediate node.
* moved the smc driver from drivers/bus to drivers/memmory
* smc driver now accepts timings in nanoseconds as well as raw register values
* smc driver can clip the timings if they're out of bound and dump them to the
console
* DM9000 timings are now described in nanosecs (for the virtue of example)
supported features are:
* working with the Common Clock Framework and the old at91 clock implementation
* dbgu
* lcdc
* usb host
* usb gadget,
* spi dataflash
* nand flash
* touchscreen
* leds
* user buttons
In the TODO list:
* dm9000 (ethernet)
* audio
* mmc
This serie relies on the following patchs:
usb: at91-udc: fix irq and iomem resource retrieval
ARM: at91: prepare sam9 dt boards transition to common
Jean-Jacques
Jean-Jacques Hiblot (8):
at91: dt: Adds support for the bus matrix declaration in the DT
at91: pinctrl: don't request GPIOs used for interrupts but lock them
as IRQ
at91: dt: Add at91sam9261 dt SoC support
at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
at91: dt: sam9261: Device Tree support for the at91sam9261ek
at91: updated the at91_dt_defconfig with support for the ADS7846
ARM: at91: prepare common clk transition for sam9261 SoC
ARM: at91: move sam9261 SoC to common clk
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/at91sam9261.dtsi | 740 ++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/at91sam9261ek.dts | 204 ++++++++++
arch/arm/configs/at91_dt_defconfig | 2 +
arch/arm/mach-at91/Kconfig | 1 -
arch/arm/mach-at91/at91sam9261.c | 25 +-
arch/arm/mach-at91/setup.c | 23 ++
drivers/pinctrl/pinctrl-at91.c | 5 +-
8 files changed, 996 insertions(+), 6 deletions(-)
create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi
create mode 100644 arch/arm/boot/dts/at91sam9261ek.dts
--
1.8.5.3
^ permalink raw reply [flat|nested] 54+ messages in thread* [PATCH v4 0/8] Device Tree support for the at91sam9261ek @ 2014-02-12 10:06 ` Jean-Jacques Hiblot 0 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: linux-arm-kernel This patch set aims at bringing a device tree support for the sam9261. It's mostly based on the sam9263 and sam9x5 stuff. Changes since V3: * Added support for the touchscreen * Added support for the spi dataflash * Activated the TCB by default * Reworked the patch organization to reduce the number of patchs * changed the default bootargs (no mem description, UBI on mtdpart 5) * Changed the xlate implementation of the at91 pinctrl driver to lock the GPIOs for IRQs instead of requesting them (needed for the touchscreen driver) * some stylistic changes Changes since V2: * removed the smc driver from the serie. It'll be posted in an independent serie later. * removed the DM9000 support (it'll come with the smc driver) * the sam9261 now supports the Common Clock Framework (CCF). Note: to enable the CCF you must remove from the kernel config the platforms that don't support it. * Added basic DT binding for the bus matrix * Added support for USB host * Added support for USB gadget * in dts(i), replaced interrupt-parent with interrupts-extended * changed the nand partition plan (same as for the sama5d3) * removed 'mem' parameter in command line * re-ordered dt-nodes in ascending address order. * split the lcd support patch in 2 parts (SOC and board) Change since V1: * changed the DT representation to use address translation and separate the timings' configuration from the device properties by adding a "simple-bus" inetrmediate node. * moved the smc driver from drivers/bus to drivers/memmory * smc driver now accepts timings in nanoseconds as well as raw register values * smc driver can clip the timings if they're out of bound and dump them to the console * DM9000 timings are now described in nanosecs (for the virtue of example) supported features are: * working with the Common Clock Framework and the old at91 clock implementation * dbgu * lcdc * usb host * usb gadget, * spi dataflash * nand flash * touchscreen * leds * user buttons In the TODO list: * dm9000 (ethernet) * audio * mmc This serie relies on the following patchs: usb: at91-udc: fix irq and iomem resource retrieval ARM: at91: prepare sam9 dt boards transition to common Jean-Jacques Jean-Jacques Hiblot (8): at91: dt: Adds support for the bus matrix declaration in the DT at91: pinctrl: don't request GPIOs used for interrupts but lock them as IRQ at91: dt: Add at91sam9261 dt SoC support at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs at91: dt: sam9261: Device Tree support for the at91sam9261ek at91: updated the at91_dt_defconfig with support for the ADS7846 ARM: at91: prepare common clk transition for sam9261 SoC ARM: at91: move sam9261 SoC to common clk arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/at91sam9261.dtsi | 740 ++++++++++++++++++++++++++++++++++++ arch/arm/boot/dts/at91sam9261ek.dts | 204 ++++++++++ arch/arm/configs/at91_dt_defconfig | 2 + arch/arm/mach-at91/Kconfig | 1 - arch/arm/mach-at91/at91sam9261.c | 25 +- arch/arm/mach-at91/setup.c | 23 ++ drivers/pinctrl/pinctrl-at91.c | 5 +- 8 files changed, 996 insertions(+), 6 deletions(-) create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi create mode 100644 arch/arm/boot/dts/at91sam9261ek.dts -- 1.8.5.3 ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 1/8] at91: dt: Adds support for the bus matrix declaration in the DT 2014-02-12 10:06 ` Jean-Jacques Hiblot @ 2014-02-12 10:06 ` Jean-Jacques Hiblot -1 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: nicolas.ferre, plagnioj, b.brezillon Cc: linux-kernel, linux-arm-kernel, gregory.clement, Jean-Jacques Hiblot Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> --- arch/arm/mach-at91/setup.c | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c index f7ca97b..b8d0b66 100644 --- a/arch/arm/mach-at91/setup.c +++ b/arch/arm/mach-at91/setup.c @@ -487,6 +487,28 @@ end: of_node_put(np); } +static struct of_device_id matrix_ids[] = { + { .compatible = "atmel,at91sam9261-bus-matrix", }, + { /*sentinel*/ } +}; + +static void at91_dt_matrix(void) +{ + struct device_node *np; + + np = of_find_matching_node(NULL, matrix_ids); + if (!np) { + pr_debug("AT91: unable to find compatible bus matrix controller node in dtb\n"); + return; + } + + at91_matrix_base = of_iomap(np, 0); + if (!at91_matrix_base) + panic("Impossible to ioremap at91_matrix_base\n"); + + of_node_put(np); +} + void __init at91rm9200_dt_initialize(void) { at91_dt_ramc(); @@ -506,6 +528,7 @@ void __init at91_dt_initialize(void) at91_dt_rstc(); at91_dt_ramc(); at91_dt_shdwc(); + at91_dt_matrix(); /* Init clock subsystem */ at91_dt_clock_init(); -- 1.8.5.3 ^ permalink raw reply related [flat|nested] 54+ messages in thread
* [PATCH v4 1/8] at91: dt: Adds support for the bus matrix declaration in the DT @ 2014-02-12 10:06 ` Jean-Jacques Hiblot 0 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: linux-arm-kernel Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> --- arch/arm/mach-at91/setup.c | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c index f7ca97b..b8d0b66 100644 --- a/arch/arm/mach-at91/setup.c +++ b/arch/arm/mach-at91/setup.c @@ -487,6 +487,28 @@ end: of_node_put(np); } +static struct of_device_id matrix_ids[] = { + { .compatible = "atmel,at91sam9261-bus-matrix", }, + { /*sentinel*/ } +}; + +static void at91_dt_matrix(void) +{ + struct device_node *np; + + np = of_find_matching_node(NULL, matrix_ids); + if (!np) { + pr_debug("AT91: unable to find compatible bus matrix controller node in dtb\n"); + return; + } + + at91_matrix_base = of_iomap(np, 0); + if (!at91_matrix_base) + panic("Impossible to ioremap at91_matrix_base\n"); + + of_node_put(np); +} + void __init at91rm9200_dt_initialize(void) { at91_dt_ramc(); @@ -506,6 +528,7 @@ void __init at91_dt_initialize(void) at91_dt_rstc(); at91_dt_ramc(); at91_dt_shdwc(); + at91_dt_matrix(); /* Init clock subsystem */ at91_dt_clock_init(); -- 1.8.5.3 ^ permalink raw reply related [flat|nested] 54+ messages in thread
* Re: [PATCH v4 1/8] at91: dt: Adds support for the bus matrix declaration in the DT 2014-02-12 10:06 ` Jean-Jacques Hiblot @ 2014-02-12 10:45 ` Gregory CLEMENT -1 siblings, 0 replies; 54+ messages in thread From: Gregory CLEMENT @ 2014-02-12 10:45 UTC (permalink / raw) To: Jean-Jacques Hiblot, nicolas.ferre, plagnioj, b.brezillon Cc: linux-kernel, linux-arm-kernel Hi Jean-Jacques, Thanks for this new series, I have one little comment: On 12/02/2014 11:06, Jean-Jacques Hiblot wrote: > Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> > --- > arch/arm/mach-at91/setup.c | 23 +++++++++++++++++++++++ > 1 file changed, 23 insertions(+) > > diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c > index f7ca97b..b8d0b66 100644 > --- a/arch/arm/mach-at91/setup.c > +++ b/arch/arm/mach-at91/setup.c > @@ -487,6 +487,28 @@ end: > of_node_put(np); > } > > +static struct of_device_id matrix_ids[] = { > + { .compatible = "atmel,at91sam9261-bus-matrix", }, > + { /*sentinel*/ } > +}; > + > +static void at91_dt_matrix(void) > +{ > + struct device_node *np; > + > + np = of_find_matching_node(NULL, matrix_ids); > + if (!np) { > + pr_debug("AT91: unable to find compatible bus matrix controller node in dtb\n"); I think that a panic here should be more consistent with the next check. Indeed if it fails here then at91_matrix_base will be uninitialized too, and it will make the kernel crash when at91_matrix_base will be accessed. Thanks, Gregory > + return; > + } > + > + at91_matrix_base = of_iomap(np, 0); > + if (!at91_matrix_base) > + panic("Impossible to ioremap at91_matrix_base\n"); > + > + of_node_put(np); > +} > + > void __init at91rm9200_dt_initialize(void) > { > at91_dt_ramc(); > @@ -506,6 +528,7 @@ void __init at91_dt_initialize(void) > at91_dt_rstc(); > at91_dt_ramc(); > at91_dt_shdwc(); > + at91_dt_matrix(); > > /* Init clock subsystem */ > at91_dt_clock_init(); > -- Gregory Clement, Free Electrons Kernel, drivers, real-time and embedded Linux development, consulting, training and support. http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 1/8] at91: dt: Adds support for the bus matrix declaration in the DT @ 2014-02-12 10:45 ` Gregory CLEMENT 0 siblings, 0 replies; 54+ messages in thread From: Gregory CLEMENT @ 2014-02-12 10:45 UTC (permalink / raw) To: linux-arm-kernel Hi Jean-Jacques, Thanks for this new series, I have one little comment: On 12/02/2014 11:06, Jean-Jacques Hiblot wrote: > Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> > --- > arch/arm/mach-at91/setup.c | 23 +++++++++++++++++++++++ > 1 file changed, 23 insertions(+) > > diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c > index f7ca97b..b8d0b66 100644 > --- a/arch/arm/mach-at91/setup.c > +++ b/arch/arm/mach-at91/setup.c > @@ -487,6 +487,28 @@ end: > of_node_put(np); > } > > +static struct of_device_id matrix_ids[] = { > + { .compatible = "atmel,at91sam9261-bus-matrix", }, > + { /*sentinel*/ } > +}; > + > +static void at91_dt_matrix(void) > +{ > + struct device_node *np; > + > + np = of_find_matching_node(NULL, matrix_ids); > + if (!np) { > + pr_debug("AT91: unable to find compatible bus matrix controller node in dtb\n"); I think that a panic here should be more consistent with the next check. Indeed if it fails here then at91_matrix_base will be uninitialized too, and it will make the kernel crash when at91_matrix_base will be accessed. Thanks, Gregory > + return; > + } > + > + at91_matrix_base = of_iomap(np, 0); > + if (!at91_matrix_base) > + panic("Impossible to ioremap at91_matrix_base\n"); > + > + of_node_put(np); > +} > + > void __init at91rm9200_dt_initialize(void) > { > at91_dt_ramc(); > @@ -506,6 +528,7 @@ void __init at91_dt_initialize(void) > at91_dt_rstc(); > at91_dt_ramc(); > at91_dt_shdwc(); > + at91_dt_matrix(); > > /* Init clock subsystem */ > at91_dt_clock_init(); > -- Gregory Clement, Free Electrons Kernel, drivers, real-time and embedded Linux development, consulting, training and support. http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [PATCH v4 1/8] at91: dt: Adds support for the bus matrix declaration in the DT 2014-02-12 10:45 ` Gregory CLEMENT @ 2014-02-12 10:54 ` Nicolas Ferre -1 siblings, 0 replies; 54+ messages in thread From: Nicolas Ferre @ 2014-02-12 10:54 UTC (permalink / raw) To: Gregory CLEMENT, Jean-Jacques Hiblot, b.brezillon Cc: plagnioj, linux-kernel, linux-arm-kernel On 12/02/2014 11:45, Gregory CLEMENT : > Hi Jean-Jacques, > > Thanks for this new series, I have one little comment: > > On 12/02/2014 11:06, Jean-Jacques Hiblot wrote: >> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> >> --- >> arch/arm/mach-at91/setup.c | 23 +++++++++++++++++++++++ >> 1 file changed, 23 insertions(+) >> >> diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c >> index f7ca97b..b8d0b66 100644 >> --- a/arch/arm/mach-at91/setup.c >> +++ b/arch/arm/mach-at91/setup.c >> @@ -487,6 +487,28 @@ end: >> of_node_put(np); >> } >> >> +static struct of_device_id matrix_ids[] = { >> + { .compatible = "atmel,at91sam9261-bus-matrix", }, >> + { /*sentinel*/ } I think that we can introduce this compatible string with sam9260 product: "atmel,at91sam9260-bus-matrix". In addition, can you add this new binding in the documentation file: Documentation/devicetree/bindings/arm/atmel-at91.txt (in another patch with the "dt: bindings: " subject prefix + add the DT mailing-list: devicetree@vger.kernel.org). >> +}; >> + >> +static void at91_dt_matrix(void) >> +{ >> + struct device_node *np; >> + >> + np = of_find_matching_node(NULL, matrix_ids); >> + if (!np) { >> + pr_debug("AT91: unable to find compatible bus matrix controller node in dtb\n"); > > I think that a panic here should be more consistent with the next check. > Indeed if it fails here then at91_matrix_base will be uninitialized too, > and it will make the kernel crash when at91_matrix_base will be accessed. Yes. > Thanks, > > Gregory > > >> + return; >> + } >> + >> + at91_matrix_base = of_iomap(np, 0); >> + if (!at91_matrix_base) >> + panic("Impossible to ioremap at91_matrix_base\n"); >> + >> + of_node_put(np); >> +} >> + >> void __init at91rm9200_dt_initialize(void) >> { >> at91_dt_ramc(); >> @@ -506,6 +528,7 @@ void __init at91_dt_initialize(void) >> at91_dt_rstc(); >> at91_dt_ramc(); >> at91_dt_shdwc(); >> + at91_dt_matrix(); >> >> /* Init clock subsystem */ >> at91_dt_clock_init(); >> > > -- Nicolas Ferre ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 1/8] at91: dt: Adds support for the bus matrix declaration in the DT @ 2014-02-12 10:54 ` Nicolas Ferre 0 siblings, 0 replies; 54+ messages in thread From: Nicolas Ferre @ 2014-02-12 10:54 UTC (permalink / raw) To: linux-arm-kernel On 12/02/2014 11:45, Gregory CLEMENT : > Hi Jean-Jacques, > > Thanks for this new series, I have one little comment: > > On 12/02/2014 11:06, Jean-Jacques Hiblot wrote: >> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> >> --- >> arch/arm/mach-at91/setup.c | 23 +++++++++++++++++++++++ >> 1 file changed, 23 insertions(+) >> >> diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c >> index f7ca97b..b8d0b66 100644 >> --- a/arch/arm/mach-at91/setup.c >> +++ b/arch/arm/mach-at91/setup.c >> @@ -487,6 +487,28 @@ end: >> of_node_put(np); >> } >> >> +static struct of_device_id matrix_ids[] = { >> + { .compatible = "atmel,at91sam9261-bus-matrix", }, >> + { /*sentinel*/ } I think that we can introduce this compatible string with sam9260 product: "atmel,at91sam9260-bus-matrix". In addition, can you add this new binding in the documentation file: Documentation/devicetree/bindings/arm/atmel-at91.txt (in another patch with the "dt: bindings: " subject prefix + add the DT mailing-list: devicetree at vger.kernel.org). >> +}; >> + >> +static void at91_dt_matrix(void) >> +{ >> + struct device_node *np; >> + >> + np = of_find_matching_node(NULL, matrix_ids); >> + if (!np) { >> + pr_debug("AT91: unable to find compatible bus matrix controller node in dtb\n"); > > I think that a panic here should be more consistent with the next check. > Indeed if it fails here then at91_matrix_base will be uninitialized too, > and it will make the kernel crash when at91_matrix_base will be accessed. Yes. > Thanks, > > Gregory > > >> + return; >> + } >> + >> + at91_matrix_base = of_iomap(np, 0); >> + if (!at91_matrix_base) >> + panic("Impossible to ioremap at91_matrix_base\n"); >> + >> + of_node_put(np); >> +} >> + >> void __init at91rm9200_dt_initialize(void) >> { >> at91_dt_ramc(); >> @@ -506,6 +528,7 @@ void __init at91_dt_initialize(void) >> at91_dt_rstc(); >> at91_dt_ramc(); >> at91_dt_shdwc(); >> + at91_dt_matrix(); >> >> /* Init clock subsystem */ >> at91_dt_clock_init(); >> > > -- Nicolas Ferre ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 2/8] at91: pinctrl: don't request GPIOs used for interrupts but lock them as IRQ 2014-02-12 10:06 ` Jean-Jacques Hiblot @ 2014-02-12 10:06 ` Jean-Jacques Hiblot -1 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: nicolas.ferre, plagnioj, b.brezillon Cc: linux-kernel, linux-arm-kernel, gregory.clement, Jean-Jacques Hiblot During the xlate stage of the DT interrupt parsing, the at91 pinctrl driver requests the GPIOs that are described as interrupt sources. This prevents a driver to request the gpio later to get its electrical value. This patch replaces the gpio_request with a gpio_lock_as_irq to prevent the gpio to be set as an ouput while allowing a subsequent gpio_request to succeed Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> --- drivers/pinctrl/pinctrl-at91.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) diff --git a/drivers/pinctrl/pinctrl-at91.c b/drivers/pinctrl/pinctrl-at91.c index d990e33..db55b96 100644 --- a/drivers/pinctrl/pinctrl-at91.c +++ b/drivers/pinctrl/pinctrl-at91.c @@ -1478,18 +1478,17 @@ static int at91_gpio_irq_domain_xlate(struct irq_domain *d, { struct at91_gpio_chip *at91_gpio = d->host_data; int ret; - int pin = at91_gpio->chip.base + intspec[0]; if (WARN_ON(intsize < 2)) return -EINVAL; *out_hwirq = intspec[0]; *out_type = intspec[1] & IRQ_TYPE_SENSE_MASK; - ret = gpio_request(pin, ctrlr->full_name); + ret = gpio_lock_as_irq(&at91_gpio->chip, intspec[0]); if (ret) return ret; - ret = gpio_direction_input(pin); + ret = at91_gpio_direction_input(&at91_gpio->chip, intspec[0]); if (ret) return ret; -- 1.8.5.3 ^ permalink raw reply related [flat|nested] 54+ messages in thread
* [PATCH v4 2/8] at91: pinctrl: don't request GPIOs used for interrupts but lock them as IRQ @ 2014-02-12 10:06 ` Jean-Jacques Hiblot 0 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: linux-arm-kernel During the xlate stage of the DT interrupt parsing, the at91 pinctrl driver requests the GPIOs that are described as interrupt sources. This prevents a driver to request the gpio later to get its electrical value. This patch replaces the gpio_request with a gpio_lock_as_irq to prevent the gpio to be set as an ouput while allowing a subsequent gpio_request to succeed Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> --- drivers/pinctrl/pinctrl-at91.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) diff --git a/drivers/pinctrl/pinctrl-at91.c b/drivers/pinctrl/pinctrl-at91.c index d990e33..db55b96 100644 --- a/drivers/pinctrl/pinctrl-at91.c +++ b/drivers/pinctrl/pinctrl-at91.c @@ -1478,18 +1478,17 @@ static int at91_gpio_irq_domain_xlate(struct irq_domain *d, { struct at91_gpio_chip *at91_gpio = d->host_data; int ret; - int pin = at91_gpio->chip.base + intspec[0]; if (WARN_ON(intsize < 2)) return -EINVAL; *out_hwirq = intspec[0]; *out_type = intspec[1] & IRQ_TYPE_SENSE_MASK; - ret = gpio_request(pin, ctrlr->full_name); + ret = gpio_lock_as_irq(&at91_gpio->chip, intspec[0]); if (ret) return ret; - ret = gpio_direction_input(pin); + ret = at91_gpio_direction_input(&at91_gpio->chip, intspec[0]); if (ret) return ret; -- 1.8.5.3 ^ permalink raw reply related [flat|nested] 54+ messages in thread
* Re: [PATCH v4 2/8] at91: pinctrl: don't request GPIOs used for interrupts but lock them as IRQ 2014-02-12 10:06 ` Jean-Jacques Hiblot @ 2014-02-12 17:47 ` Nicolas Ferre -1 siblings, 0 replies; 54+ messages in thread From: Nicolas Ferre @ 2014-02-12 17:47 UTC (permalink / raw) To: Jean-Jacques Hiblot, b.brezillon, Linus Walleij Cc: plagnioj, linux-kernel, linux-arm-kernel, gregory.clement On 12/02/2014 11:06, Jean-Jacques Hiblot : > During the xlate stage of the DT interrupt parsing, the at91 pinctrl driver > requests the GPIOs that are described as interrupt sources. This prevents a > driver to request the gpio later to get its electrical value. > This patch replaces the gpio_request with a gpio_lock_as_irq to prevent the > gpio to be set as an ouput while allowing a subsequent gpio_request to succeed > > Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> But I suspect it may go through another patch: the pinctrl one: add Linux W. to the recipient list please. Thanks, > --- > drivers/pinctrl/pinctrl-at91.c | 5 ++--- > 1 file changed, 2 insertions(+), 3 deletions(-) > > diff --git a/drivers/pinctrl/pinctrl-at91.c b/drivers/pinctrl/pinctrl-at91.c > index d990e33..db55b96 100644 > --- a/drivers/pinctrl/pinctrl-at91.c > +++ b/drivers/pinctrl/pinctrl-at91.c > @@ -1478,18 +1478,17 @@ static int at91_gpio_irq_domain_xlate(struct irq_domain *d, > { > struct at91_gpio_chip *at91_gpio = d->host_data; > int ret; > - int pin = at91_gpio->chip.base + intspec[0]; > > if (WARN_ON(intsize < 2)) > return -EINVAL; > *out_hwirq = intspec[0]; > *out_type = intspec[1] & IRQ_TYPE_SENSE_MASK; > > - ret = gpio_request(pin, ctrlr->full_name); > + ret = gpio_lock_as_irq(&at91_gpio->chip, intspec[0]); > if (ret) > return ret; > > - ret = gpio_direction_input(pin); > + ret = at91_gpio_direction_input(&at91_gpio->chip, intspec[0]); > if (ret) > return ret; > > -- Nicolas Ferre ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 2/8] at91: pinctrl: don't request GPIOs used for interrupts but lock them as IRQ @ 2014-02-12 17:47 ` Nicolas Ferre 0 siblings, 0 replies; 54+ messages in thread From: Nicolas Ferre @ 2014-02-12 17:47 UTC (permalink / raw) To: linux-arm-kernel On 12/02/2014 11:06, Jean-Jacques Hiblot : > During the xlate stage of the DT interrupt parsing, the at91 pinctrl driver > requests the GPIOs that are described as interrupt sources. This prevents a > driver to request the gpio later to get its electrical value. > This patch replaces the gpio_request with a gpio_lock_as_irq to prevent the > gpio to be set as an ouput while allowing a subsequent gpio_request to succeed > > Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> But I suspect it may go through another patch: the pinctrl one: add Linux W. to the recipient list please. Thanks, > --- > drivers/pinctrl/pinctrl-at91.c | 5 ++--- > 1 file changed, 2 insertions(+), 3 deletions(-) > > diff --git a/drivers/pinctrl/pinctrl-at91.c b/drivers/pinctrl/pinctrl-at91.c > index d990e33..db55b96 100644 > --- a/drivers/pinctrl/pinctrl-at91.c > +++ b/drivers/pinctrl/pinctrl-at91.c > @@ -1478,18 +1478,17 @@ static int at91_gpio_irq_domain_xlate(struct irq_domain *d, > { > struct at91_gpio_chip *at91_gpio = d->host_data; > int ret; > - int pin = at91_gpio->chip.base + intspec[0]; > > if (WARN_ON(intsize < 2)) > return -EINVAL; > *out_hwirq = intspec[0]; > *out_type = intspec[1] & IRQ_TYPE_SENSE_MASK; > > - ret = gpio_request(pin, ctrlr->full_name); > + ret = gpio_lock_as_irq(&at91_gpio->chip, intspec[0]); > if (ret) > return ret; > > - ret = gpio_direction_input(pin); > + ret = at91_gpio_direction_input(&at91_gpio->chip, intspec[0]); > if (ret) > return ret; > > -- Nicolas Ferre ^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [PATCH v4 2/8] at91: pinctrl: don't request GPIOs used for interrupts but lock them as IRQ 2014-02-12 10:06 ` Jean-Jacques Hiblot @ 2014-02-24 13:25 ` Linus Walleij -1 siblings, 0 replies; 54+ messages in thread From: Linus Walleij @ 2014-02-24 13:25 UTC (permalink / raw) To: Jean-Jacques Hiblot Cc: Nicolas Ferre, Jean-Christophe PLAGNIOL-VILLARD, boris brezillon, Gregory CLEMENT, linux-kernel, linux-arm-kernel On Wed, Feb 12, 2014 at 11:06 AM, Jean-Jacques Hiblot <jjhiblot@traphandler.com> wrote: > During the xlate stage of the DT interrupt parsing, the at91 pinctrl driver > requests the GPIOs that are described as interrupt sources. This prevents a > driver to request the gpio later to get its electrical value. > This patch replaces the gpio_request with a gpio_lock_as_irq to prevent the > gpio to be set as an ouput while allowing a subsequent gpio_request to succeed > > Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> OK, but is this really correct: > @@ -1478,18 +1478,17 @@ static int at91_gpio_irq_domain_xlate(struct irq_domain *d, > { > struct at91_gpio_chip *at91_gpio = d->host_data; > int ret; > - int pin = at91_gpio->chip.base + intspec[0]; > > if (WARN_ON(intsize < 2)) > return -EINVAL; > *out_hwirq = intspec[0]; > *out_type = intspec[1] & IRQ_TYPE_SENSE_MASK; > > - ret = gpio_request(pin, ctrlr->full_name); > + ret = gpio_lock_as_irq(&at91_gpio->chip, intspec[0]); So when resolving an IRQ resource, we take for granted that it will be used for IRQs and IRQs only? Is it not possible that this resolution is done and then the driver using it unloads or whatever and it is still marked as IRQ? I don't think the xlate function should have such side effects on the gpio_chip internal state. I think it should just translate. The line is locked for IRQ the moment its startup() callback is called, is it not? > - ret = gpio_direction_input(pin); > + ret = at91_gpio_direction_input(&at91_gpio->chip, intspec[0]); I actually don't like this either. This kind of thing was causing problems in the OMAP driver like hell. I think this should be deleted from xlate and at91_gpio_direction_input() be called from the irqchip's .startup() or even .unmask() function instead. Yours, Linus Walleij ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 2/8] at91: pinctrl: don't request GPIOs used for interrupts but lock them as IRQ @ 2014-02-24 13:25 ` Linus Walleij 0 siblings, 0 replies; 54+ messages in thread From: Linus Walleij @ 2014-02-24 13:25 UTC (permalink / raw) To: linux-arm-kernel On Wed, Feb 12, 2014 at 11:06 AM, Jean-Jacques Hiblot <jjhiblot@traphandler.com> wrote: > During the xlate stage of the DT interrupt parsing, the at91 pinctrl driver > requests the GPIOs that are described as interrupt sources. This prevents a > driver to request the gpio later to get its electrical value. > This patch replaces the gpio_request with a gpio_lock_as_irq to prevent the > gpio to be set as an ouput while allowing a subsequent gpio_request to succeed > > Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> OK, but is this really correct: > @@ -1478,18 +1478,17 @@ static int at91_gpio_irq_domain_xlate(struct irq_domain *d, > { > struct at91_gpio_chip *at91_gpio = d->host_data; > int ret; > - int pin = at91_gpio->chip.base + intspec[0]; > > if (WARN_ON(intsize < 2)) > return -EINVAL; > *out_hwirq = intspec[0]; > *out_type = intspec[1] & IRQ_TYPE_SENSE_MASK; > > - ret = gpio_request(pin, ctrlr->full_name); > + ret = gpio_lock_as_irq(&at91_gpio->chip, intspec[0]); So when resolving an IRQ resource, we take for granted that it will be used for IRQs and IRQs only? Is it not possible that this resolution is done and then the driver using it unloads or whatever and it is still marked as IRQ? I don't think the xlate function should have such side effects on the gpio_chip internal state. I think it should just translate. The line is locked for IRQ the moment its startup() callback is called, is it not? > - ret = gpio_direction_input(pin); > + ret = at91_gpio_direction_input(&at91_gpio->chip, intspec[0]); I actually don't like this either. This kind of thing was causing problems in the OMAP driver like hell. I think this should be deleted from xlate and at91_gpio_direction_input() be called from the irqchip's .startup() or even .unmask() function instead. Yours, Linus Walleij ^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [PATCH v4 2/8] at91: pinctrl: don't request GPIOs used for interrupts but lock them as IRQ 2014-02-24 13:25 ` Linus Walleij @ 2014-02-25 9:35 ` Jean-Jacques Hiblot -1 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-25 9:35 UTC (permalink / raw) To: Linus Walleij Cc: Jean-Jacques Hiblot, Nicolas Ferre, Jean-Christophe PLAGNIOL-VILLARD, boris brezillon, Gregory CLEMENT, linux-kernel, linux-arm-kernel Hi Linus, 2014-02-24 14:25 GMT+01:00 Linus Walleij <linus.walleij@linaro.org>: > On Wed, Feb 12, 2014 at 11:06 AM, Jean-Jacques Hiblot > <jjhiblot@traphandler.com> wrote: > >> During the xlate stage of the DT interrupt parsing, the at91 pinctrl driver >> requests the GPIOs that are described as interrupt sources. This prevents a >> driver to request the gpio later to get its electrical value. >> This patch replaces the gpio_request with a gpio_lock_as_irq to prevent the >> gpio to be set as an ouput while allowing a subsequent gpio_request to succeed >> >> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> > > OK, but is this really correct: > >> @@ -1478,18 +1478,17 @@ static int at91_gpio_irq_domain_xlate(struct irq_domain *d, >> { >> struct at91_gpio_chip *at91_gpio = d->host_data; >> int ret; >> - int pin = at91_gpio->chip.base + intspec[0]; >> >> if (WARN_ON(intsize < 2)) >> return -EINVAL; >> *out_hwirq = intspec[0]; >> *out_type = intspec[1] & IRQ_TYPE_SENSE_MASK; >> >> - ret = gpio_request(pin, ctrlr->full_name); >> + ret = gpio_lock_as_irq(&at91_gpio->chip, intspec[0]); > > So when resolving an IRQ resource, we take for granted that it will be used > for IRQs and IRQs only? Is it not possible that this resolution is done > and then the driver using it unloads or whatever and it is still marked > as IRQ? No, once it's reserved for irq, it'll be for irq only. > > I don't think the xlate function should have such side effects on > the gpio_chip internal state. I think it should just translate. I agree but I choose to only replace the gpio_request by a lock_as_irq(), not rework the whole thing. It seemed it would have more chance to be accepted this way. IMO the right time to do this is at the time of the request_irq() > > The line is locked for IRQ the moment its startup() callback is > called, is it not? > >> - ret = gpio_direction_input(pin); >> + ret = at91_gpio_direction_input(&at91_gpio->chip, intspec[0]); > > I actually don't like this either. This kind of thing was causing > problems in the OMAP driver like hell. But calling gpio_direction_input() defeats the purpose of removing the gpio_request() because it ensures that the gpio is requested. > > I think this should be deleted from xlate and at91_gpio_direction_input() > be called from the irqchip's .startup() or even .unmask() function > instead. irq_startup and irq_shutdown seem the right place for this because they're called when requesting and freeing the interrupt. It'll require a change to __setup_irq() though to check the return value of irq_startup. Jean-Jacques > > Yours, > Linus Walleij ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 2/8] at91: pinctrl: don't request GPIOs used for interrupts but lock them as IRQ @ 2014-02-25 9:35 ` Jean-Jacques Hiblot 0 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-25 9:35 UTC (permalink / raw) To: linux-arm-kernel Hi Linus, 2014-02-24 14:25 GMT+01:00 Linus Walleij <linus.walleij@linaro.org>: > On Wed, Feb 12, 2014 at 11:06 AM, Jean-Jacques Hiblot > <jjhiblot@traphandler.com> wrote: > >> During the xlate stage of the DT interrupt parsing, the at91 pinctrl driver >> requests the GPIOs that are described as interrupt sources. This prevents a >> driver to request the gpio later to get its electrical value. >> This patch replaces the gpio_request with a gpio_lock_as_irq to prevent the >> gpio to be set as an ouput while allowing a subsequent gpio_request to succeed >> >> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> > > OK, but is this really correct: > >> @@ -1478,18 +1478,17 @@ static int at91_gpio_irq_domain_xlate(struct irq_domain *d, >> { >> struct at91_gpio_chip *at91_gpio = d->host_data; >> int ret; >> - int pin = at91_gpio->chip.base + intspec[0]; >> >> if (WARN_ON(intsize < 2)) >> return -EINVAL; >> *out_hwirq = intspec[0]; >> *out_type = intspec[1] & IRQ_TYPE_SENSE_MASK; >> >> - ret = gpio_request(pin, ctrlr->full_name); >> + ret = gpio_lock_as_irq(&at91_gpio->chip, intspec[0]); > > So when resolving an IRQ resource, we take for granted that it will be used > for IRQs and IRQs only? Is it not possible that this resolution is done > and then the driver using it unloads or whatever and it is still marked > as IRQ? No, once it's reserved for irq, it'll be for irq only. > > I don't think the xlate function should have such side effects on > the gpio_chip internal state. I think it should just translate. I agree but I choose to only replace the gpio_request by a lock_as_irq(), not rework the whole thing. It seemed it would have more chance to be accepted this way. IMO the right time to do this is at the time of the request_irq() > > The line is locked for IRQ the moment its startup() callback is > called, is it not? > >> - ret = gpio_direction_input(pin); >> + ret = at91_gpio_direction_input(&at91_gpio->chip, intspec[0]); > > I actually don't like this either. This kind of thing was causing > problems in the OMAP driver like hell. But calling gpio_direction_input() defeats the purpose of removing the gpio_request() because it ensures that the gpio is requested. > > I think this should be deleted from xlate and at91_gpio_direction_input() > be called from the irqchip's .startup() or even .unmask() function > instead. irq_startup and irq_shutdown seem the right place for this because they're called when requesting and freeing the interrupt. It'll require a change to __setup_irq() though to check the return value of irq_startup. Jean-Jacques > > Yours, > Linus Walleij ^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [PATCH v4 2/8] at91: pinctrl: don't request GPIOs used for interrupts but lock them as IRQ 2014-02-25 9:35 ` Jean-Jacques Hiblot @ 2014-02-25 9:47 ` Jean-Jacques Hiblot -1 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-25 9:47 UTC (permalink / raw) To: Jean-Jacques Hiblot Cc: Linus Walleij, Nicolas Ferre, Jean-Christophe PLAGNIOL-VILLARD, boris brezillon, Gregory CLEMENT, linux-kernel, linux-arm-kernel 2014-02-25 10:35 GMT+01:00 Jean-Jacques Hiblot <jjhiblot@traphandler.com>: > Hi Linus, > > 2014-02-24 14:25 GMT+01:00 Linus Walleij <linus.walleij@linaro.org>: >> On Wed, Feb 12, 2014 at 11:06 AM, Jean-Jacques Hiblot >> <jjhiblot@traphandler.com> wrote: >> >>> During the xlate stage of the DT interrupt parsing, the at91 pinctrl driver >>> requests the GPIOs that are described as interrupt sources. This prevents a >>> driver to request the gpio later to get its electrical value. >>> This patch replaces the gpio_request with a gpio_lock_as_irq to prevent the >>> gpio to be set as an ouput while allowing a subsequent gpio_request to succeed >>> >>> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> >> >> OK, but is this really correct: >> >>> @@ -1478,18 +1478,17 @@ static int at91_gpio_irq_domain_xlate(struct irq_domain *d, >>> { >>> struct at91_gpio_chip *at91_gpio = d->host_data; >>> int ret; >>> - int pin = at91_gpio->chip.base + intspec[0]; >>> >>> if (WARN_ON(intsize < 2)) >>> return -EINVAL; >>> *out_hwirq = intspec[0]; >>> *out_type = intspec[1] & IRQ_TYPE_SENSE_MASK; >>> >>> - ret = gpio_request(pin, ctrlr->full_name); >>> + ret = gpio_lock_as_irq(&at91_gpio->chip, intspec[0]); >> >> So when resolving an IRQ resource, we take for granted that it will be used >> for IRQs and IRQs only? Is it not possible that this resolution is done >> and then the driver using it unloads or whatever and it is still marked >> as IRQ? > No, once it's reserved for irq, it'll be for irq only. >> >> I don't think the xlate function should have such side effects on >> the gpio_chip internal state. I think it should just translate. > > I agree but I choose to only replace the gpio_request by a > lock_as_irq(), not rework the whole thing. It seemed it would have > more chance to be accepted this way. IMO the right time to do this is > at the time of the request_irq() >> >> The line is locked for IRQ the moment its startup() callback is >> called, is it not? >> >>> - ret = gpio_direction_input(pin); >>> + ret = at91_gpio_direction_input(&at91_gpio->chip, intspec[0]); >> >> I actually don't like this either. This kind of thing was causing >> problems in the OMAP driver like hell. > But calling gpio_direction_input() defeats the purpose of removing the > gpio_request() because it ensures that the gpio is requested. >> >> I think this should be deleted from xlate and at91_gpio_direction_input() >> be called from the irqchip's .startup() or even .unmask() function >> instead. > irq_startup and irq_shutdown seem the right place for this because > they're called when requesting and freeing the interrupt. It'll > require a change to __setup_irq() though to check the return value of > irq_startup. Linux, Sorry, for the noise. You can forget this proposed patch and my previous email. I just saw that the patch where this was done in startup and shutdown was applied. I thought it had been rejected . I'm sorry for the confusion. Jean-Jacques >> >> Yours, >> Linus Walleij ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 2/8] at91: pinctrl: don't request GPIOs used for interrupts but lock them as IRQ @ 2014-02-25 9:47 ` Jean-Jacques Hiblot 0 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-25 9:47 UTC (permalink / raw) To: linux-arm-kernel 2014-02-25 10:35 GMT+01:00 Jean-Jacques Hiblot <jjhiblot@traphandler.com>: > Hi Linus, > > 2014-02-24 14:25 GMT+01:00 Linus Walleij <linus.walleij@linaro.org>: >> On Wed, Feb 12, 2014 at 11:06 AM, Jean-Jacques Hiblot >> <jjhiblot@traphandler.com> wrote: >> >>> During the xlate stage of the DT interrupt parsing, the at91 pinctrl driver >>> requests the GPIOs that are described as interrupt sources. This prevents a >>> driver to request the gpio later to get its electrical value. >>> This patch replaces the gpio_request with a gpio_lock_as_irq to prevent the >>> gpio to be set as an ouput while allowing a subsequent gpio_request to succeed >>> >>> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> >> >> OK, but is this really correct: >> >>> @@ -1478,18 +1478,17 @@ static int at91_gpio_irq_domain_xlate(struct irq_domain *d, >>> { >>> struct at91_gpio_chip *at91_gpio = d->host_data; >>> int ret; >>> - int pin = at91_gpio->chip.base + intspec[0]; >>> >>> if (WARN_ON(intsize < 2)) >>> return -EINVAL; >>> *out_hwirq = intspec[0]; >>> *out_type = intspec[1] & IRQ_TYPE_SENSE_MASK; >>> >>> - ret = gpio_request(pin, ctrlr->full_name); >>> + ret = gpio_lock_as_irq(&at91_gpio->chip, intspec[0]); >> >> So when resolving an IRQ resource, we take for granted that it will be used >> for IRQs and IRQs only? Is it not possible that this resolution is done >> and then the driver using it unloads or whatever and it is still marked >> as IRQ? > No, once it's reserved for irq, it'll be for irq only. >> >> I don't think the xlate function should have such side effects on >> the gpio_chip internal state. I think it should just translate. > > I agree but I choose to only replace the gpio_request by a > lock_as_irq(), not rework the whole thing. It seemed it would have > more chance to be accepted this way. IMO the right time to do this is > at the time of the request_irq() >> >> The line is locked for IRQ the moment its startup() callback is >> called, is it not? >> >>> - ret = gpio_direction_input(pin); >>> + ret = at91_gpio_direction_input(&at91_gpio->chip, intspec[0]); >> >> I actually don't like this either. This kind of thing was causing >> problems in the OMAP driver like hell. > But calling gpio_direction_input() defeats the purpose of removing the > gpio_request() because it ensures that the gpio is requested. >> >> I think this should be deleted from xlate and at91_gpio_direction_input() >> be called from the irqchip's .startup() or even .unmask() function >> instead. > irq_startup and irq_shutdown seem the right place for this because > they're called when requesting and freeing the interrupt. It'll > require a change to __setup_irq() though to check the return value of > irq_startup. Linux, Sorry, for the noise. You can forget this proposed patch and my previous email. I just saw that the patch where this was done in startup and shutdown was applied. I thought it had been rejected . I'm sorry for the confusion. Jean-Jacques >> >> Yours, >> Linus Walleij ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 3/8] at91: dt: Add at91sam9261 dt SoC support 2014-02-12 10:06 ` Jean-Jacques Hiblot @ 2014-02-12 10:06 ` Jean-Jacques Hiblot -1 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: nicolas.ferre, plagnioj, b.brezillon Cc: linux-kernel, linux-arm-kernel, gregory.clement, Jean-Jacques Hiblot This patch adds support for the Device Tree on a sam9261-based platform Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> --- arch/arm/boot/dts/at91sam9261.dtsi | 740 +++++++++++++++++++++++++++++++++++++ arch/arm/mach-at91/at91sam9261.c | 17 + 2 files changed, 757 insertions(+) create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi new file mode 100644 index 0000000..a95bfb3 --- /dev/null +++ b/arch/arm/boot/dts/at91sam9261.dtsi @@ -0,0 +1,740 @@ +/* + * at91sam9261.dtsi - Device Tree Include file for AT91SAM9261 SoC + * + * Copyright (C) 2013 Jean-Jacques Hiblot <jjhiblot@traphandler.com> + * + * Licensed under GPLv2 only. + */ + +#include "skeleton.dtsi" +#include <dt-bindings/pinctrl/at91.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/clk/at91.h> + +/ { + model = "Atmel AT91SAM9261 family SoC"; + compatible = "atmel,at91sam9261"; + interrupt-parent = <&aic>; + + aliases { + serial0 = &dbgu; + serial1 = &usart0; + serial2 = &usart1; + serial3 = &usart2; + gpio0 = &pioA; + gpio1 = &pioB; + gpio2 = &pioC; + tcb0 = &tcb0; + i2c0 = &i2c0; + ssc0 = &ssc0; + ssc1 = &ssc1; + }; + + cpus { + #address-cells = <0>; + #size-cells = <0>; + + cpu { + compatible = "arm,arm926ej-s"; + device_type = "cpu"; + }; + }; + + memory { + reg = <0x20000000 0x08000000>; + }; + + ahb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + usb0: ohci@00500000 { + compatible = "atmel,at91rm9200-ohci", "usb-ohci"; + reg = <0x00500000 0x100000>; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH 2>; + clocks = <&usb>, <&ohci_clk>, <&hclk0>, <&uhpck>; + clock-names = "usb_clk", "ohci_clk", "hclk", "uhpck"; + status = "disabled"; + }; + + fb0: fb@0x00600000 { + compatible = "atmel,at91sam9261-lcdc"; + reg = <0x00600000 0x1000>; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fb>; + clocks = <&lcd_clk>, <&hclk1>; + clock-names = "lcdc_clk", "hclk"; + status = "disabled"; + }; + + nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x40000000 0x10000000>; + atmel,nand-addr-offset = <22>; + atmel,nand-cmd-offset = <21>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_nand>; + + gpios = <&pioC 15 GPIO_ACTIVE_HIGH + &pioC 14 GPIO_ACTIVE_HIGH + 0 + >; + status = "disabled"; + }; + + apb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + tcb0: timer@fffa0000 { + compatible = "atmel,at91rm9200-tcb"; + reg = <0xfffa0000 0x100>; + interrupts = < 17 IRQ_TYPE_LEVEL_HIGH 0 + 18 IRQ_TYPE_LEVEL_HIGH 0 + 19 IRQ_TYPE_LEVEL_HIGH 0 + >; + clocks = <&tc0_clk>, <&tc1_clk>, <&tc2_clk>; + clock-names = "t0_clk", "t1_clk", "t2_clk"; + }; + + usb1: gadget@fffa4000 { + compatible = "atmel,at91rm9200-udc"; + reg = <0xfffa4000 0x4000>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>; + clocks = <&usb>, <&udc_clk>, <&udpck>; + clock-names = "usb_clk", "udc_clk", "udpck"; + status = "disabled"; + }; + + mmc0: mmc@fffa8000 { + compatible = "atmel,hsmci"; + reg = <0xfffa8000 0x600>; + interrupts = <9 IRQ_TYPE_LEVEL_HIGH 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc0_clk>, <&pinctrl_mmc0_slot0_cmd_dat0>, <&pinctrl_mmc0_slot0_dat1_3>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&mci0_clk>; + clock-names = "mci_clk"; + status = "disabled"; + }; + + i2c0: i2c@fffac000 { + compatible = "atmel,at91sam9261-i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c_twi>; + reg = <0xfffac000 0x100>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&twi0_clk>; + status = "disabled"; + }; + + usart0: serial@fffb0000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffb0000 0x200>; + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>; + atmel,use-dma-rx; + atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart0>; + clocks = <&usart0_clk>; + clock-names = "usart"; + status = "disabled"; + }; + + usart1: serial@fffb4000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffb4000 0x200>; + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>; + atmel,use-dma-rx; + atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart1>; + clocks = <&usart1_clk>; + clock-names = "usart"; + status = "disabled"; + }; + + usart2: serial@fffb8000{ + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffb8000 0x200>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>; + atmel,use-dma-rx; + atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart2>; + clocks = <&usart2_clk>; + clock-names = "usart"; + status = "disabled"; + }; + + ssc0: ssc@fffbc000 { + compatible = "atmel,at91rm9200-ssc"; + reg = <0xfffbc000 0x4000>; + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; + status = "disabled"; + }; + + ssc1: ssc@fffc0000 { + compatible = "atmel,at91rm9200-ssc"; + reg = <0xfffc0000 0x4000>; + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; + status = "disabled"; + }; + + spi0: spi@fffc8000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91rm9200-spi"; + reg = <0xfffc8000 0x200>; + cs-gpios = <0>, <0>, <0>, <0>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi0>; + clocks = <&spi0_clk>; + clock-names = "spi_clk"; + status = "disabled"; + }; + + spi1: spi@fffcc000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91rm9200-spi"; + reg = <0xfffcc000 0x200>; + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1>; + clocks = <&spi1_clk>; + clock-names = "spi_clk"; + status = "disabled"; + }; + + ramc: ramc@ffffea00 { + compatible = "atmel,at91sam9260-sdramc"; + reg = <0xffffea00 0x200>; + }; + + matrix: matrix@ffffee00 { + compatible = "atmel,at91sam9261-bus-matrix"; + reg = <0xffffee00 0x200>; + }; + + aic: interrupt-controller@fffff000 { + #interrupt-cells = <3>; + compatible = "atmel,at91rm9200-aic"; + interrupt-controller; + reg = <0xfffff000 0x200>; + atmel,external-irqs = <29 30 31>; + }; + + dbgu: serial@fffff200 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffff200 0x200>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dbgu>; + clocks = <&mck>; + clock-names = "usart"; + status = "disabled"; + }; + + pinctrl@fffff400 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; + ranges = <0xfffff400 0xfffff400 0xa00>; + + atmel,mux-mask = < + /* A B */ + 0xffffffff 0xfffffff7 /* pioA */ + 0xffffffff 0xfffffff4 /* pioB */ + 0xffffffff 0xffffff07 /* pioC */ + >; + + /* shared pinctrl settings */ + dbgu { + pinctrl_dbgu: dbgu-0 { + atmel,pins = + <AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; + }; + }; + + usart0 { + pinctrl_usart0: usart0-0 { + atmel,pins = + <AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP + AT91_PIOC 9 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_usart0_rts: usart0_rts-0 { + atmel,pins = + <AT91_PIOC 10 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_usart0_cts: usart0_cts-0 { + atmel,pins = + <AT91_PIOC 11 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + }; + + usart1 { + pinctrl_usart1: usart1-0 { + atmel,pins = + <AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP + AT91_PIOC 13 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_usart1_rts: usart1_rts-0 { + atmel,pins = + <AT91_PIOA 12 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_usart1_cts: usart1_cts-0 { + atmel,pins = + <AT91_PIOA 13 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + }; + + usart2 { + pinctrl_usart2: usart2-0 { + atmel,pins = + <AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP + AT91_PIOC 15 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_usart2_rts: usart2_rts-0 { + atmel,pins = + <AT91_PIOA 15 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_usart2_cts: usart2_cts-0 { + atmel,pins = + <AT91_PIOA 16 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + }; + + nand { + pinctrl_nand: nand-0 { + atmel,pins = + <AT91_PIOC 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP + AT91_PIOC 14 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>; + }; + }; + + mmc0 { + pinctrl_mmc0_clk: mmc0_clk-0 { + atmel,pins = + <AT91_PIOA 2 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_mmc0_slot0_cmd_dat0: mmc0_slot0_cmd_dat0-0 { + atmel,pins = + <AT91_PIOA 1 AT91_PERIPH_B AT91_PINCTRL_PULL_UP + AT91_PIOA 0 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; + }; + + pinctrl_mmc0_slot0_dat1_3: mmc0_slot0_dat1_3-0 { + atmel,pins = + <AT91_PIOA 4 AT91_PERIPH_B AT91_PINCTRL_PULL_UP + AT91_PIOA 5 AT91_PERIPH_B AT91_PINCTRL_PULL_UP + AT91_PIOA 6 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; + }; + }; + + ssc0 { + pinctrl_ssc0_tx: ssc0_tx-0 { + atmel,pins = + <AT91_PIOB 21 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 22 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 23 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_ssc0_rx: ssc0_rx-0 { + atmel,pins = + <AT91_PIOB 24 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 25 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 26 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + }; + + ssc1 { + pinctrl_ssc1_tx: ssc1_tx-0 { + atmel,pins = + <AT91_PIOA 17 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOA 18 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOA 19 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_ssc1_rx: ssc1_rx-0 { + atmel,pins = + <AT91_PIOA 20 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOA 21 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOA 22 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + }; + + spi0 { + pinctrl_spi0: spi0-0 { + atmel,pins = + <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOA 2 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + }; + + spi1 { + pinctrl_spi1: spi1-0 { + atmel,pins = + <AT91_PIOB 30 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 31 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 29 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + }; + + tcb0 { + pinctrl_tcb0_tclk0: tcb0_tclk0-0 { + atmel,pins = <AT91_PIOC 16 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_tcb0_tclk1: tcb0_tclk1-0 { + atmel,pins = <AT91_PIOC 17 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_tcb0_tclk2: tcb0_tclk2-0 { + atmel,pins = <AT91_PIOC 18 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_tcb0_tioa0: tcb0_tioa0-0 { + atmel,pins = <AT91_PIOC 19 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_tcb0_tioa1: tcb0_tioa1-0 { + atmel,pins = <AT91_PIOC 21 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_tcb0_tioa2: tcb0_tioa2-0 { + atmel,pins = <AT91_PIOC 23 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_tcb0_tiob0: tcb0_tiob0-0 { + atmel,pins = <AT91_PIOC 20 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_tcb0_tiob1: tcb0_tiob1-0 { + atmel,pins = <AT91_PIOC 22 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_tcb0_tiob2: tcb0_tiob2-0 { + atmel,pins = <AT91_PIOC 24 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + }; + + i2c0 { + pinctrl_i2c_bitbang: i2c-0-bitbang { + atmel,pins = + <AT91_PIOA 7 AT91_PERIPH_GPIO AT91_PINCTRL_NONE + AT91_PIOA 8 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; + }; + pinctrl_i2c_twi: i2c-0-twi { + atmel,pins = + <AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOA 8 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + }; + + fb { + pinctrl_fb: fb-0 { + atmel,pins = + <AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 2 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 3 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 11 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 15 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 16 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 17 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 18 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 20 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 23 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOB 24 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOB 25 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOB 26 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOB 27 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOB 28 AT91_PERIPH_B AT91_PINCTRL_NONE + >; + }; + }; + + pioA: gpio@fffff400 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff400 0x200>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&pioA_clk>; + }; + + pioB: gpio@fffff600 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff600 0x200>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&pioB_clk>; + }; + + pioC: gpio@fffff800 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff800 0x200>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&pioC_clk>; + }; + }; + + pmc: pmc@fffffc00 { + compatible = "atmel,at91rm9200-pmc"; + reg = <0xfffffc00 0x100>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; + interrupt-controller; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + + clk32k: slck { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + + main: mainck { + compatible = "atmel,at91rm9200-clk-main"; + #clock-cells = <0>; + interrupts-extended = <&pmc AT91_PMC_MOSCS>; + clocks = <&clk32k>; + }; + + plla: pllack { + compatible = "atmel,at91rm9200-clk-pll"; + #clock-cells = <0>; + interrupts-extended = <&pmc AT91_PMC_LOCKA>; + clocks = <&main>; + reg = <0>; + atmel,clk-input-range = <1000000 32000000>; + #atmel,pll-clk-output-range-cells = <4>; + atmel,pll-clk-output-ranges = <80000000 200000000 190000000 240000000>; + }; + + pllb: pllbck { + compatible = "atmel,at91rm9200-clk-pll"; + #clock-cells = <0>; + interrupts-extended = <&pmc AT91_PMC_LOCKB>; + clocks = <&main>; + reg = <1>; + atmel,clk-input-range = <1000000 32000000>; + #atmel,pll-clk-output-range-cells = <4>; + atmel,pll-clk-output-ranges = <80000000 200000000 190000000 240000000>; + }; + + mck: masterck { + compatible = "atmel,at91rm9200-clk-master"; + #clock-cells = <0>; + interrupts-extended = <&pmc AT91_PMC_MCKRDY>; + clocks = <&clk32k>, <&main>, <&plla>, <&pllb>; + atmel,clk-output-range = <0 94000000>; + atmel,clk-divisors = <1 2 4 3>; + }; + + usb: usbck { + compatible = "atmel,at91rm9200-clk-usb"; + #clock-cells = <0>; + atmel,clk-divisors = <1 2 4 3>; + clocks = <&pllb>; + }; + + systemck { + compatible = "atmel,at91rm9200-clk-system"; + #address-cells = <1>; + #size-cells = <0>; + + uhpck: uhpck { + #clock-cells = <0>; + reg = <6>; + clocks = <&usb>; + }; + + udpck: udpck { + #clock-cells = <0>; + reg = <7>; + clocks = <&usb>; + }; + + hclk0: hclk0 { + #clock-cells = <0>; + reg = <16>; + clocks = <&mck>; + }; + + hclk1: hclk1 { + #clock-cells = <0>; + reg = <17>; + clocks = <&mck>; + }; + }; + + periphck { + compatible = "atmel,at91rm9200-clk-peripheral"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&mck>; + + pioA_clk: pioA_clk { + #clock-cells = <0>; + reg = <2>; + }; + + pioB_clk: pioB_clk { + #clock-cells = <0>; + reg = <3>; + }; + + pioC_clk: pioC_clk { + #clock-cells = <0>; + reg = <4>; + }; + + usart0_clk: usart0_clk { + #clock-cells = <0>; + reg = <6>; + }; + + usart1_clk: usart1_clk { + #clock-cells = <0>; + reg = <7>; + }; + + usart2_clk: usart2_clk { + #clock-cells = <0>; + reg = <8>; + }; + + mci0_clk: mci0_clk { + #clock-cells = <0>; + reg = <9>; + }; + + udc_clk: udc_clk { + #clock-cells = <0>; + reg = <10>; + }; + + twi0_clk: twi0_clk { + reg = <11>; + #clock-cells = <0>; + }; + + spi0_clk: spi0_clk { + #clock-cells = <0>; + reg = <12>; + }; + + spi1_clk: spi1_clk { + #clock-cells = <0>; + reg = <13>; + }; + + tc0_clk: tc0_clk { + #clock-cells = <0>; + reg = <17>; + }; + + tc1_clk: tc1_clk { + #clock-cells = <0>; + reg = <18>; + }; + + tc2_clk: tc2_clk { + #clock-cells = <0>; + reg = <19>; + }; + + ohci_clk: ohci_clk { + #clock-cells = <0>; + reg = <20>; + }; + + lcd_clk: lcd_clk { + #clock-cells = <0>; + reg = <21>; + }; + }; + }; + + rstc@fffffd00 { + compatible = "atmel,at91sam9260-rstc"; + reg = <0xfffffd00 0x10>; + }; + + shdwc@fffffd10 { + compatible = "atmel,at91sam9260-shdwc"; + reg = <0xfffffd10 0x10>; + }; + + pit: timer@fffffd30 { + compatible = "atmel,at91sam9260-pit"; + reg = <0xfffffd30 0xf>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; + clocks = <&mck>; + }; + + watchdog@fffffd40 { + compatible = "atmel,at91sam9260-wdt"; + reg = <0xfffffd40 0x10>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; + status = "disabled"; + }; + }; + }; + + i2c@0 { + compatible = "i2c-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c_bitbang>; + gpios = <&pioA 7 GPIO_ACTIVE_HIGH /* sda */ + &pioA 8 GPIO_ACTIVE_HIGH /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; +}; diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c index 6276b4c..5c90581 100644 --- a/arch/arm/mach-at91/at91sam9261.c +++ b/arch/arm/mach-at91/at91sam9261.c @@ -189,6 +189,23 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_ID("pioA", &pioA_clk), CLKDEV_CON_ID("pioB", &pioB_clk), CLKDEV_CON_ID("pioC", &pioC_clk), + /* more lookup table for DT entries */ + CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck), + CLKDEV_CON_DEV_ID("usart", "fffb0000.serial", &usart0_clk), + CLKDEV_CON_DEV_ID("usart", "ffffb400.serial", &usart1_clk), + CLKDEV_CON_DEV_ID("usart", "fff94000.serial", &usart2_clk), + CLKDEV_CON_DEV_ID("t0_clk", "fffa0000.timer", &tc0_clk), + CLKDEV_CON_DEV_ID("t1_clk", "fffa0000.timer", &tc1_clk), + CLKDEV_CON_DEV_ID("t2_clk", "fffa0000.timer", &tc2_clk), + CLKDEV_CON_DEV_ID("hclk", "500000.ohci", &hck0), + CLKDEV_CON_DEV_ID("hclk", "600000.fb", &hck1), + CLKDEV_CON_DEV_ID("spi_clk", "fffc8000.spi", &spi0_clk), + CLKDEV_CON_DEV_ID("spi_clk", "fffcc000.spi", &spi1_clk), + CLKDEV_CON_DEV_ID("mci_clk", "fffa8000.mmc", &mmc_clk), + CLKDEV_CON_DEV_ID(NULL, "fffac000.i2c", &twi_clk), + CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioA_clk), + CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioB_clk), + CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioC_clk), }; static struct clk_lookup usart_clocks_lookups[] = { -- 1.8.5.3 ^ permalink raw reply related [flat|nested] 54+ messages in thread
* [PATCH v4 3/8] at91: dt: Add at91sam9261 dt SoC support @ 2014-02-12 10:06 ` Jean-Jacques Hiblot 0 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: linux-arm-kernel This patch adds support for the Device Tree on a sam9261-based platform Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> --- arch/arm/boot/dts/at91sam9261.dtsi | 740 +++++++++++++++++++++++++++++++++++++ arch/arm/mach-at91/at91sam9261.c | 17 + 2 files changed, 757 insertions(+) create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi new file mode 100644 index 0000000..a95bfb3 --- /dev/null +++ b/arch/arm/boot/dts/at91sam9261.dtsi @@ -0,0 +1,740 @@ +/* + * at91sam9261.dtsi - Device Tree Include file for AT91SAM9261 SoC + * + * Copyright (C) 2013 Jean-Jacques Hiblot <jjhiblot@traphandler.com> + * + * Licensed under GPLv2 only. + */ + +#include "skeleton.dtsi" +#include <dt-bindings/pinctrl/at91.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/clk/at91.h> + +/ { + model = "Atmel AT91SAM9261 family SoC"; + compatible = "atmel,at91sam9261"; + interrupt-parent = <&aic>; + + aliases { + serial0 = &dbgu; + serial1 = &usart0; + serial2 = &usart1; + serial3 = &usart2; + gpio0 = &pioA; + gpio1 = &pioB; + gpio2 = &pioC; + tcb0 = &tcb0; + i2c0 = &i2c0; + ssc0 = &ssc0; + ssc1 = &ssc1; + }; + + cpus { + #address-cells = <0>; + #size-cells = <0>; + + cpu { + compatible = "arm,arm926ej-s"; + device_type = "cpu"; + }; + }; + + memory { + reg = <0x20000000 0x08000000>; + }; + + ahb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + usb0: ohci at 00500000 { + compatible = "atmel,at91rm9200-ohci", "usb-ohci"; + reg = <0x00500000 0x100000>; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH 2>; + clocks = <&usb>, <&ohci_clk>, <&hclk0>, <&uhpck>; + clock-names = "usb_clk", "ohci_clk", "hclk", "uhpck"; + status = "disabled"; + }; + + fb0: fb at 0x00600000 { + compatible = "atmel,at91sam9261-lcdc"; + reg = <0x00600000 0x1000>; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fb>; + clocks = <&lcd_clk>, <&hclk1>; + clock-names = "lcdc_clk", "hclk"; + status = "disabled"; + }; + + nand0: nand at 40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x40000000 0x10000000>; + atmel,nand-addr-offset = <22>; + atmel,nand-cmd-offset = <21>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_nand>; + + gpios = <&pioC 15 GPIO_ACTIVE_HIGH + &pioC 14 GPIO_ACTIVE_HIGH + 0 + >; + status = "disabled"; + }; + + apb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + tcb0: timer at fffa0000 { + compatible = "atmel,at91rm9200-tcb"; + reg = <0xfffa0000 0x100>; + interrupts = < 17 IRQ_TYPE_LEVEL_HIGH 0 + 18 IRQ_TYPE_LEVEL_HIGH 0 + 19 IRQ_TYPE_LEVEL_HIGH 0 + >; + clocks = <&tc0_clk>, <&tc1_clk>, <&tc2_clk>; + clock-names = "t0_clk", "t1_clk", "t2_clk"; + }; + + usb1: gadget at fffa4000 { + compatible = "atmel,at91rm9200-udc"; + reg = <0xfffa4000 0x4000>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>; + clocks = <&usb>, <&udc_clk>, <&udpck>; + clock-names = "usb_clk", "udc_clk", "udpck"; + status = "disabled"; + }; + + mmc0: mmc at fffa8000 { + compatible = "atmel,hsmci"; + reg = <0xfffa8000 0x600>; + interrupts = <9 IRQ_TYPE_LEVEL_HIGH 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc0_clk>, <&pinctrl_mmc0_slot0_cmd_dat0>, <&pinctrl_mmc0_slot0_dat1_3>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&mci0_clk>; + clock-names = "mci_clk"; + status = "disabled"; + }; + + i2c0: i2c at fffac000 { + compatible = "atmel,at91sam9261-i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c_twi>; + reg = <0xfffac000 0x100>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&twi0_clk>; + status = "disabled"; + }; + + usart0: serial at fffb0000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffb0000 0x200>; + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>; + atmel,use-dma-rx; + atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart0>; + clocks = <&usart0_clk>; + clock-names = "usart"; + status = "disabled"; + }; + + usart1: serial at fffb4000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffb4000 0x200>; + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>; + atmel,use-dma-rx; + atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart1>; + clocks = <&usart1_clk>; + clock-names = "usart"; + status = "disabled"; + }; + + usart2: serial at fffb8000{ + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffb8000 0x200>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>; + atmel,use-dma-rx; + atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart2>; + clocks = <&usart2_clk>; + clock-names = "usart"; + status = "disabled"; + }; + + ssc0: ssc at fffbc000 { + compatible = "atmel,at91rm9200-ssc"; + reg = <0xfffbc000 0x4000>; + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; + status = "disabled"; + }; + + ssc1: ssc at fffc0000 { + compatible = "atmel,at91rm9200-ssc"; + reg = <0xfffc0000 0x4000>; + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; + status = "disabled"; + }; + + spi0: spi at fffc8000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91rm9200-spi"; + reg = <0xfffc8000 0x200>; + cs-gpios = <0>, <0>, <0>, <0>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi0>; + clocks = <&spi0_clk>; + clock-names = "spi_clk"; + status = "disabled"; + }; + + spi1: spi at fffcc000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91rm9200-spi"; + reg = <0xfffcc000 0x200>; + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1>; + clocks = <&spi1_clk>; + clock-names = "spi_clk"; + status = "disabled"; + }; + + ramc: ramc at ffffea00 { + compatible = "atmel,at91sam9260-sdramc"; + reg = <0xffffea00 0x200>; + }; + + matrix: matrix at ffffee00 { + compatible = "atmel,at91sam9261-bus-matrix"; + reg = <0xffffee00 0x200>; + }; + + aic: interrupt-controller at fffff000 { + #interrupt-cells = <3>; + compatible = "atmel,at91rm9200-aic"; + interrupt-controller; + reg = <0xfffff000 0x200>; + atmel,external-irqs = <29 30 31>; + }; + + dbgu: serial at fffff200 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffff200 0x200>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dbgu>; + clocks = <&mck>; + clock-names = "usart"; + status = "disabled"; + }; + + pinctrl at fffff400 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; + ranges = <0xfffff400 0xfffff400 0xa00>; + + atmel,mux-mask = < + /* A B */ + 0xffffffff 0xfffffff7 /* pioA */ + 0xffffffff 0xfffffff4 /* pioB */ + 0xffffffff 0xffffff07 /* pioC */ + >; + + /* shared pinctrl settings */ + dbgu { + pinctrl_dbgu: dbgu-0 { + atmel,pins = + <AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; + }; + }; + + usart0 { + pinctrl_usart0: usart0-0 { + atmel,pins = + <AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP + AT91_PIOC 9 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_usart0_rts: usart0_rts-0 { + atmel,pins = + <AT91_PIOC 10 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_usart0_cts: usart0_cts-0 { + atmel,pins = + <AT91_PIOC 11 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + }; + + usart1 { + pinctrl_usart1: usart1-0 { + atmel,pins = + <AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP + AT91_PIOC 13 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_usart1_rts: usart1_rts-0 { + atmel,pins = + <AT91_PIOA 12 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_usart1_cts: usart1_cts-0 { + atmel,pins = + <AT91_PIOA 13 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + }; + + usart2 { + pinctrl_usart2: usart2-0 { + atmel,pins = + <AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP + AT91_PIOC 15 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_usart2_rts: usart2_rts-0 { + atmel,pins = + <AT91_PIOA 15 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_usart2_cts: usart2_cts-0 { + atmel,pins = + <AT91_PIOA 16 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + }; + + nand { + pinctrl_nand: nand-0 { + atmel,pins = + <AT91_PIOC 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP + AT91_PIOC 14 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>; + }; + }; + + mmc0 { + pinctrl_mmc0_clk: mmc0_clk-0 { + atmel,pins = + <AT91_PIOA 2 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_mmc0_slot0_cmd_dat0: mmc0_slot0_cmd_dat0-0 { + atmel,pins = + <AT91_PIOA 1 AT91_PERIPH_B AT91_PINCTRL_PULL_UP + AT91_PIOA 0 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; + }; + + pinctrl_mmc0_slot0_dat1_3: mmc0_slot0_dat1_3-0 { + atmel,pins = + <AT91_PIOA 4 AT91_PERIPH_B AT91_PINCTRL_PULL_UP + AT91_PIOA 5 AT91_PERIPH_B AT91_PINCTRL_PULL_UP + AT91_PIOA 6 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; + }; + }; + + ssc0 { + pinctrl_ssc0_tx: ssc0_tx-0 { + atmel,pins = + <AT91_PIOB 21 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 22 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 23 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_ssc0_rx: ssc0_rx-0 { + atmel,pins = + <AT91_PIOB 24 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 25 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 26 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + }; + + ssc1 { + pinctrl_ssc1_tx: ssc1_tx-0 { + atmel,pins = + <AT91_PIOA 17 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOA 18 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOA 19 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_ssc1_rx: ssc1_rx-0 { + atmel,pins = + <AT91_PIOA 20 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOA 21 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOA 22 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + }; + + spi0 { + pinctrl_spi0: spi0-0 { + atmel,pins = + <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOA 2 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + }; + + spi1 { + pinctrl_spi1: spi1-0 { + atmel,pins = + <AT91_PIOB 30 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 31 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 29 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + }; + + tcb0 { + pinctrl_tcb0_tclk0: tcb0_tclk0-0 { + atmel,pins = <AT91_PIOC 16 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_tcb0_tclk1: tcb0_tclk1-0 { + atmel,pins = <AT91_PIOC 17 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_tcb0_tclk2: tcb0_tclk2-0 { + atmel,pins = <AT91_PIOC 18 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_tcb0_tioa0: tcb0_tioa0-0 { + atmel,pins = <AT91_PIOC 19 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_tcb0_tioa1: tcb0_tioa1-0 { + atmel,pins = <AT91_PIOC 21 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_tcb0_tioa2: tcb0_tioa2-0 { + atmel,pins = <AT91_PIOC 23 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_tcb0_tiob0: tcb0_tiob0-0 { + atmel,pins = <AT91_PIOC 20 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_tcb0_tiob1: tcb0_tiob1-0 { + atmel,pins = <AT91_PIOC 22 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_tcb0_tiob2: tcb0_tiob2-0 { + atmel,pins = <AT91_PIOC 24 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + }; + + i2c0 { + pinctrl_i2c_bitbang: i2c-0-bitbang { + atmel,pins = + <AT91_PIOA 7 AT91_PERIPH_GPIO AT91_PINCTRL_NONE + AT91_PIOA 8 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; + }; + pinctrl_i2c_twi: i2c-0-twi { + atmel,pins = + <AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOA 8 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + }; + + fb { + pinctrl_fb: fb-0 { + atmel,pins = + <AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 2 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 3 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 11 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 15 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 16 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 17 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 18 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 20 AT91_PERIPH_A AT91_PINCTRL_NONE + AT91_PIOB 23 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOB 24 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOB 25 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOB 26 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOB 27 AT91_PERIPH_B AT91_PINCTRL_NONE + AT91_PIOB 28 AT91_PERIPH_B AT91_PINCTRL_NONE + >; + }; + }; + + pioA: gpio at fffff400 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff400 0x200>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&pioA_clk>; + }; + + pioB: gpio at fffff600 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff600 0x200>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&pioB_clk>; + }; + + pioC: gpio at fffff800 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff800 0x200>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&pioC_clk>; + }; + }; + + pmc: pmc at fffffc00 { + compatible = "atmel,at91rm9200-pmc"; + reg = <0xfffffc00 0x100>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; + interrupt-controller; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + + clk32k: slck { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + + main: mainck { + compatible = "atmel,at91rm9200-clk-main"; + #clock-cells = <0>; + interrupts-extended = <&pmc AT91_PMC_MOSCS>; + clocks = <&clk32k>; + }; + + plla: pllack { + compatible = "atmel,at91rm9200-clk-pll"; + #clock-cells = <0>; + interrupts-extended = <&pmc AT91_PMC_LOCKA>; + clocks = <&main>; + reg = <0>; + atmel,clk-input-range = <1000000 32000000>; + #atmel,pll-clk-output-range-cells = <4>; + atmel,pll-clk-output-ranges = <80000000 200000000 190000000 240000000>; + }; + + pllb: pllbck { + compatible = "atmel,at91rm9200-clk-pll"; + #clock-cells = <0>; + interrupts-extended = <&pmc AT91_PMC_LOCKB>; + clocks = <&main>; + reg = <1>; + atmel,clk-input-range = <1000000 32000000>; + #atmel,pll-clk-output-range-cells = <4>; + atmel,pll-clk-output-ranges = <80000000 200000000 190000000 240000000>; + }; + + mck: masterck { + compatible = "atmel,at91rm9200-clk-master"; + #clock-cells = <0>; + interrupts-extended = <&pmc AT91_PMC_MCKRDY>; + clocks = <&clk32k>, <&main>, <&plla>, <&pllb>; + atmel,clk-output-range = <0 94000000>; + atmel,clk-divisors = <1 2 4 3>; + }; + + usb: usbck { + compatible = "atmel,at91rm9200-clk-usb"; + #clock-cells = <0>; + atmel,clk-divisors = <1 2 4 3>; + clocks = <&pllb>; + }; + + systemck { + compatible = "atmel,at91rm9200-clk-system"; + #address-cells = <1>; + #size-cells = <0>; + + uhpck: uhpck { + #clock-cells = <0>; + reg = <6>; + clocks = <&usb>; + }; + + udpck: udpck { + #clock-cells = <0>; + reg = <7>; + clocks = <&usb>; + }; + + hclk0: hclk0 { + #clock-cells = <0>; + reg = <16>; + clocks = <&mck>; + }; + + hclk1: hclk1 { + #clock-cells = <0>; + reg = <17>; + clocks = <&mck>; + }; + }; + + periphck { + compatible = "atmel,at91rm9200-clk-peripheral"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&mck>; + + pioA_clk: pioA_clk { + #clock-cells = <0>; + reg = <2>; + }; + + pioB_clk: pioB_clk { + #clock-cells = <0>; + reg = <3>; + }; + + pioC_clk: pioC_clk { + #clock-cells = <0>; + reg = <4>; + }; + + usart0_clk: usart0_clk { + #clock-cells = <0>; + reg = <6>; + }; + + usart1_clk: usart1_clk { + #clock-cells = <0>; + reg = <7>; + }; + + usart2_clk: usart2_clk { + #clock-cells = <0>; + reg = <8>; + }; + + mci0_clk: mci0_clk { + #clock-cells = <0>; + reg = <9>; + }; + + udc_clk: udc_clk { + #clock-cells = <0>; + reg = <10>; + }; + + twi0_clk: twi0_clk { + reg = <11>; + #clock-cells = <0>; + }; + + spi0_clk: spi0_clk { + #clock-cells = <0>; + reg = <12>; + }; + + spi1_clk: spi1_clk { + #clock-cells = <0>; + reg = <13>; + }; + + tc0_clk: tc0_clk { + #clock-cells = <0>; + reg = <17>; + }; + + tc1_clk: tc1_clk { + #clock-cells = <0>; + reg = <18>; + }; + + tc2_clk: tc2_clk { + #clock-cells = <0>; + reg = <19>; + }; + + ohci_clk: ohci_clk { + #clock-cells = <0>; + reg = <20>; + }; + + lcd_clk: lcd_clk { + #clock-cells = <0>; + reg = <21>; + }; + }; + }; + + rstc at fffffd00 { + compatible = "atmel,at91sam9260-rstc"; + reg = <0xfffffd00 0x10>; + }; + + shdwc at fffffd10 { + compatible = "atmel,at91sam9260-shdwc"; + reg = <0xfffffd10 0x10>; + }; + + pit: timer at fffffd30 { + compatible = "atmel,at91sam9260-pit"; + reg = <0xfffffd30 0xf>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; + clocks = <&mck>; + }; + + watchdog at fffffd40 { + compatible = "atmel,at91sam9260-wdt"; + reg = <0xfffffd40 0x10>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; + status = "disabled"; + }; + }; + }; + + i2c at 0 { + compatible = "i2c-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c_bitbang>; + gpios = <&pioA 7 GPIO_ACTIVE_HIGH /* sda */ + &pioA 8 GPIO_ACTIVE_HIGH /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; +}; diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c index 6276b4c..5c90581 100644 --- a/arch/arm/mach-at91/at91sam9261.c +++ b/arch/arm/mach-at91/at91sam9261.c @@ -189,6 +189,23 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_ID("pioA", &pioA_clk), CLKDEV_CON_ID("pioB", &pioB_clk), CLKDEV_CON_ID("pioC", &pioC_clk), + /* more lookup table for DT entries */ + CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck), + CLKDEV_CON_DEV_ID("usart", "fffb0000.serial", &usart0_clk), + CLKDEV_CON_DEV_ID("usart", "ffffb400.serial", &usart1_clk), + CLKDEV_CON_DEV_ID("usart", "fff94000.serial", &usart2_clk), + CLKDEV_CON_DEV_ID("t0_clk", "fffa0000.timer", &tc0_clk), + CLKDEV_CON_DEV_ID("t1_clk", "fffa0000.timer", &tc1_clk), + CLKDEV_CON_DEV_ID("t2_clk", "fffa0000.timer", &tc2_clk), + CLKDEV_CON_DEV_ID("hclk", "500000.ohci", &hck0), + CLKDEV_CON_DEV_ID("hclk", "600000.fb", &hck1), + CLKDEV_CON_DEV_ID("spi_clk", "fffc8000.spi", &spi0_clk), + CLKDEV_CON_DEV_ID("spi_clk", "fffcc000.spi", &spi1_clk), + CLKDEV_CON_DEV_ID("mci_clk", "fffa8000.mmc", &mmc_clk), + CLKDEV_CON_DEV_ID(NULL, "fffac000.i2c", &twi_clk), + CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioA_clk), + CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioB_clk), + CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioC_clk), }; static struct clk_lookup usart_clocks_lookups[] = { -- 1.8.5.3 ^ permalink raw reply related [flat|nested] 54+ messages in thread
* Re: [PATCH v4 3/8] at91: dt: Add at91sam9261 dt SoC support 2014-02-12 10:06 ` Jean-Jacques Hiblot @ 2014-02-12 17:28 ` Alexandre Belloni -1 siblings, 0 replies; 54+ messages in thread From: Alexandre Belloni @ 2014-02-12 17:28 UTC (permalink / raw) To: Jean-Jacques Hiblot Cc: nicolas.ferre, plagnioj, b.brezillon, gregory.clement, linux-kernel, linux-arm-kernel Hi, On 12/02/2014 at 11:06:42 +0100, Jean-Jacques Hiblot wrote : > This patch adds support for the Device Tree on a sam9261-based platform > > Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> > --- > arch/arm/boot/dts/at91sam9261.dtsi | 740 +++++++++++++++++++++++++++++++++++++ > arch/arm/mach-at91/at91sam9261.c | 17 + > 2 files changed, 757 insertions(+) > create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi [...] > + > + apb { > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + tcb0: timer@fffa0000 { > + compatible = "atmel,at91rm9200-tcb"; > + reg = <0xfffa0000 0x100>; > + interrupts = < 17 IRQ_TYPE_LEVEL_HIGH 0 > + 18 IRQ_TYPE_LEVEL_HIGH 0 > + 19 IRQ_TYPE_LEVEL_HIGH 0 > + >; > + clocks = <&tc0_clk>, <&tc1_clk>, <&tc2_clk>; > + clock-names = "t0_clk", "t1_clk", "t2_clk"; > + }; > + > + usb1: gadget@fffa4000 { > + compatible = "atmel,at91rm9200-udc"; > + reg = <0xfffa4000 0x4000>; > + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>; > + clocks = <&usb>, <&udc_clk>, <&udpck>; > + clock-names = "usb_clk", "udc_clk", "udpck"; > + status = "disabled"; > + }; > + > + mmc0: mmc@fffa8000 { > + compatible = "atmel,hsmci"; > + reg = <0xfffa8000 0x600>; > + interrupts = <9 IRQ_TYPE_LEVEL_HIGH 0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_mmc0_clk>, <&pinctrl_mmc0_slot0_cmd_dat0>, <&pinctrl_mmc0_slot0_dat1_3>; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&mci0_clk>; > + clock-names = "mci_clk"; > + status = "disabled"; > + }; > + > + i2c0: i2c@fffac000 { > + compatible = "atmel,at91sam9261-i2c"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c_twi>; > + reg = <0xfffac000 0x100>; > + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&twi0_clk>; > + status = "disabled"; > + }; > + > + usart0: serial@fffb0000 { > + compatible = "atmel,at91sam9260-usart"; > + reg = <0xfffb0000 0x200>; > + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>; > + atmel,use-dma-rx; > + atmel,use-dma-tx; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usart0>; > + clocks = <&usart0_clk>; > + clock-names = "usart"; > + status = "disabled"; > + }; > + > + usart1: serial@fffb4000 { > + compatible = "atmel,at91sam9260-usart"; > + reg = <0xfffb4000 0x200>; > + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>; > + atmel,use-dma-rx; > + atmel,use-dma-tx; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usart1>; > + clocks = <&usart1_clk>; > + clock-names = "usart"; > + status = "disabled"; > + }; > + > + usart2: serial@fffb8000{ > + compatible = "atmel,at91sam9260-usart"; > + reg = <0xfffb8000 0x200>; > + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>; > + atmel,use-dma-rx; > + atmel,use-dma-tx; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usart2>; > + clocks = <&usart2_clk>; > + clock-names = "usart"; > + status = "disabled"; > + }; > + > + ssc0: ssc@fffbc000 { > + compatible = "atmel,at91rm9200-ssc"; > + reg = <0xfffbc000 0x4000>; > + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; > + status = "disabled"; > + }; > + > + ssc1: ssc@fffc0000 { > + compatible = "atmel,at91rm9200-ssc"; > + reg = <0xfffc0000 0x4000>; > + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; > + status = "disabled"; > + }; > + > + spi0: spi@fffc8000 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "atmel,at91rm9200-spi"; > + reg = <0xfffc8000 0x200>; > + cs-gpios = <0>, <0>, <0>, <0>; > + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 3>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_spi0>; > + clocks = <&spi0_clk>; > + clock-names = "spi_clk"; > + status = "disabled"; > + }; > + > + spi1: spi@fffcc000 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "atmel,at91rm9200-spi"; > + reg = <0xfffcc000 0x200>; > + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_spi1>; > + clocks = <&spi1_clk>; > + clock-names = "spi_clk"; > + status = "disabled"; > + }; > + > + ramc: ramc@ffffea00 { > + compatible = "atmel,at91sam9260-sdramc"; > + reg = <0xffffea00 0x200>; > + }; > + You probably copied/pasted it but according to the block diagram, the sdram controller is not under the apb. > + matrix: matrix@ffffee00 { > + compatible = "atmel,at91sam9261-bus-matrix"; > + reg = <0xffffee00 0x200>; > + }; > + Same here, the apb is actually under the bus matrix. I don't know whether it can be represented another way though. -- Alexandre Belloni, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 3/8] at91: dt: Add at91sam9261 dt SoC support @ 2014-02-12 17:28 ` Alexandre Belloni 0 siblings, 0 replies; 54+ messages in thread From: Alexandre Belloni @ 2014-02-12 17:28 UTC (permalink / raw) To: linux-arm-kernel Hi, On 12/02/2014 at 11:06:42 +0100, Jean-Jacques Hiblot wrote : > This patch adds support for the Device Tree on a sam9261-based platform > > Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> > --- > arch/arm/boot/dts/at91sam9261.dtsi | 740 +++++++++++++++++++++++++++++++++++++ > arch/arm/mach-at91/at91sam9261.c | 17 + > 2 files changed, 757 insertions(+) > create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi [...] > + > + apb { > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + tcb0: timer at fffa0000 { > + compatible = "atmel,at91rm9200-tcb"; > + reg = <0xfffa0000 0x100>; > + interrupts = < 17 IRQ_TYPE_LEVEL_HIGH 0 > + 18 IRQ_TYPE_LEVEL_HIGH 0 > + 19 IRQ_TYPE_LEVEL_HIGH 0 > + >; > + clocks = <&tc0_clk>, <&tc1_clk>, <&tc2_clk>; > + clock-names = "t0_clk", "t1_clk", "t2_clk"; > + }; > + > + usb1: gadget at fffa4000 { > + compatible = "atmel,at91rm9200-udc"; > + reg = <0xfffa4000 0x4000>; > + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>; > + clocks = <&usb>, <&udc_clk>, <&udpck>; > + clock-names = "usb_clk", "udc_clk", "udpck"; > + status = "disabled"; > + }; > + > + mmc0: mmc at fffa8000 { > + compatible = "atmel,hsmci"; > + reg = <0xfffa8000 0x600>; > + interrupts = <9 IRQ_TYPE_LEVEL_HIGH 0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_mmc0_clk>, <&pinctrl_mmc0_slot0_cmd_dat0>, <&pinctrl_mmc0_slot0_dat1_3>; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&mci0_clk>; > + clock-names = "mci_clk"; > + status = "disabled"; > + }; > + > + i2c0: i2c at fffac000 { > + compatible = "atmel,at91sam9261-i2c"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c_twi>; > + reg = <0xfffac000 0x100>; > + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&twi0_clk>; > + status = "disabled"; > + }; > + > + usart0: serial at fffb0000 { > + compatible = "atmel,at91sam9260-usart"; > + reg = <0xfffb0000 0x200>; > + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>; > + atmel,use-dma-rx; > + atmel,use-dma-tx; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usart0>; > + clocks = <&usart0_clk>; > + clock-names = "usart"; > + status = "disabled"; > + }; > + > + usart1: serial at fffb4000 { > + compatible = "atmel,at91sam9260-usart"; > + reg = <0xfffb4000 0x200>; > + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>; > + atmel,use-dma-rx; > + atmel,use-dma-tx; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usart1>; > + clocks = <&usart1_clk>; > + clock-names = "usart"; > + status = "disabled"; > + }; > + > + usart2: serial at fffb8000{ > + compatible = "atmel,at91sam9260-usart"; > + reg = <0xfffb8000 0x200>; > + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>; > + atmel,use-dma-rx; > + atmel,use-dma-tx; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usart2>; > + clocks = <&usart2_clk>; > + clock-names = "usart"; > + status = "disabled"; > + }; > + > + ssc0: ssc at fffbc000 { > + compatible = "atmel,at91rm9200-ssc"; > + reg = <0xfffbc000 0x4000>; > + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; > + status = "disabled"; > + }; > + > + ssc1: ssc at fffc0000 { > + compatible = "atmel,at91rm9200-ssc"; > + reg = <0xfffc0000 0x4000>; > + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; > + status = "disabled"; > + }; > + > + spi0: spi at fffc8000 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "atmel,at91rm9200-spi"; > + reg = <0xfffc8000 0x200>; > + cs-gpios = <0>, <0>, <0>, <0>; > + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 3>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_spi0>; > + clocks = <&spi0_clk>; > + clock-names = "spi_clk"; > + status = "disabled"; > + }; > + > + spi1: spi at fffcc000 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "atmel,at91rm9200-spi"; > + reg = <0xfffcc000 0x200>; > + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_spi1>; > + clocks = <&spi1_clk>; > + clock-names = "spi_clk"; > + status = "disabled"; > + }; > + > + ramc: ramc at ffffea00 { > + compatible = "atmel,at91sam9260-sdramc"; > + reg = <0xffffea00 0x200>; > + }; > + You probably copied/pasted it but according to the block diagram, the sdram controller is not under the apb. > + matrix: matrix at ffffee00 { > + compatible = "atmel,at91sam9261-bus-matrix"; > + reg = <0xffffee00 0x200>; > + }; > + Same here, the apb is actually under the bus matrix. I don't know whether it can be represented another way though. -- Alexandre Belloni, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [PATCH v4 3/8] at91: dt: Add at91sam9261 dt SoC support 2014-02-12 17:28 ` Alexandre Belloni @ 2014-02-12 19:47 ` Jean-Jacques Hiblot -1 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 19:47 UTC (permalink / raw) To: Alexandre Belloni Cc: Jean-Jacques Hiblot, Nicolas Ferre, Jean-Christophe PLAGNIOL-VILLARD, boris brezillon, Gregory CLEMENT, Linux Kernel Mailing List, linux-arm-kernel Hi Alexandre, 2014-02-12 18:28 GMT+01:00 Alexandre Belloni <alexandre.belloni@free-electrons.com>: > Hi, > > On 12/02/2014 at 11:06:42 +0100, Jean-Jacques Hiblot wrote : >> This patch adds support for the Device Tree on a sam9261-based platform >> >> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> >> --- >> arch/arm/boot/dts/at91sam9261.dtsi | 740 +++++++++++++++++++++++++++++++++++++ >> arch/arm/mach-at91/at91sam9261.c | 17 + >> 2 files changed, 757 insertions(+) >> create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi > > [...] > >> + >> + apb { >> + compatible = "simple-bus"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges; >> + >> + tcb0: timer@fffa0000 { >> + compatible = "atmel,at91rm9200-tcb"; >> + reg = <0xfffa0000 0x100>; >> + interrupts = < 17 IRQ_TYPE_LEVEL_HIGH 0 >> + 18 IRQ_TYPE_LEVEL_HIGH 0 >> + 19 IRQ_TYPE_LEVEL_HIGH 0 >> + >; >> + clocks = <&tc0_clk>, <&tc1_clk>, <&tc2_clk>; >> + clock-names = "t0_clk", "t1_clk", "t2_clk"; >> + }; >> + >> + usb1: gadget@fffa4000 { >> + compatible = "atmel,at91rm9200-udc"; >> + reg = <0xfffa4000 0x4000>; >> + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>; >> + clocks = <&usb>, <&udc_clk>, <&udpck>; >> + clock-names = "usb_clk", "udc_clk", "udpck"; >> + status = "disabled"; >> + }; >> + >> + mmc0: mmc@fffa8000 { >> + compatible = "atmel,hsmci"; >> + reg = <0xfffa8000 0x600>; >> + interrupts = <9 IRQ_TYPE_LEVEL_HIGH 0>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_mmc0_clk>, <&pinctrl_mmc0_slot0_cmd_dat0>, <&pinctrl_mmc0_slot0_dat1_3>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + clocks = <&mci0_clk>; >> + clock-names = "mci_clk"; >> + status = "disabled"; >> + }; >> + >> + i2c0: i2c@fffac000 { >> + compatible = "atmel,at91sam9261-i2c"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_i2c_twi>; >> + reg = <0xfffac000 0x100>; >> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + clocks = <&twi0_clk>; >> + status = "disabled"; >> + }; >> + >> + usart0: serial@fffb0000 { >> + compatible = "atmel,at91sam9260-usart"; >> + reg = <0xfffb0000 0x200>; >> + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>; >> + atmel,use-dma-rx; >> + atmel,use-dma-tx; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_usart0>; >> + clocks = <&usart0_clk>; >> + clock-names = "usart"; >> + status = "disabled"; >> + }; >> + >> + usart1: serial@fffb4000 { >> + compatible = "atmel,at91sam9260-usart"; >> + reg = <0xfffb4000 0x200>; >> + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>; >> + atmel,use-dma-rx; >> + atmel,use-dma-tx; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_usart1>; >> + clocks = <&usart1_clk>; >> + clock-names = "usart"; >> + status = "disabled"; >> + }; >> + >> + usart2: serial@fffb8000{ >> + compatible = "atmel,at91sam9260-usart"; >> + reg = <0xfffb8000 0x200>; >> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>; >> + atmel,use-dma-rx; >> + atmel,use-dma-tx; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_usart2>; >> + clocks = <&usart2_clk>; >> + clock-names = "usart"; >> + status = "disabled"; >> + }; >> + >> + ssc0: ssc@fffbc000 { >> + compatible = "atmel,at91rm9200-ssc"; >> + reg = <0xfffbc000 0x4000>; >> + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; >> + status = "disabled"; >> + }; >> + >> + ssc1: ssc@fffc0000 { >> + compatible = "atmel,at91rm9200-ssc"; >> + reg = <0xfffc0000 0x4000>; >> + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; >> + status = "disabled"; >> + }; >> + >> + spi0: spi@fffc8000 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "atmel,at91rm9200-spi"; >> + reg = <0xfffc8000 0x200>; >> + cs-gpios = <0>, <0>, <0>, <0>; >> + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 3>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_spi0>; >> + clocks = <&spi0_clk>; >> + clock-names = "spi_clk"; >> + status = "disabled"; >> + }; >> + >> + spi1: spi@fffcc000 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "atmel,at91rm9200-spi"; >> + reg = <0xfffcc000 0x200>; >> + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_spi1>; >> + clocks = <&spi1_clk>; >> + clock-names = "spi_clk"; >> + status = "disabled"; >> + }; >> + >> + ramc: ramc@ffffea00 { >> + compatible = "atmel,at91sam9260-sdramc"; >> + reg = <0xffffea00 0x200>; >> + }; >> + > > You probably copied/pasted it but according to the block diagram, the > sdram controller is not under the apb. You're right I copied/pasted :o) But the addresses of the registers look like typical APB addresses. AFAIK all the registers of this SOC are accessed through the APB (except for OHCI and LCDC) So probably the real question here is what is the sense of the bus hierarchy in cases where a controller is connected to several buses (APB for registers, AHB/matrix for other purpose) ? As I don't have any idea on how to handle this, I choose to copy/paste. > >> + matrix: matrix@ffffee00 { >> + compatible = "atmel,at91sam9261-bus-matrix"; >> + reg = <0xffffee00 0x200>; >> + }; >> + > > Same here, the apb is actually under the bus matrix. > > I don't know whether it can be represented another way though. > > > -- > Alexandre Belloni, Free Electrons > Embedded Linux, Kernel and Android engineering > http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 3/8] at91: dt: Add at91sam9261 dt SoC support @ 2014-02-12 19:47 ` Jean-Jacques Hiblot 0 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 19:47 UTC (permalink / raw) To: linux-arm-kernel Hi Alexandre, 2014-02-12 18:28 GMT+01:00 Alexandre Belloni <alexandre.belloni@free-electrons.com>: > Hi, > > On 12/02/2014 at 11:06:42 +0100, Jean-Jacques Hiblot wrote : >> This patch adds support for the Device Tree on a sam9261-based platform >> >> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> >> --- >> arch/arm/boot/dts/at91sam9261.dtsi | 740 +++++++++++++++++++++++++++++++++++++ >> arch/arm/mach-at91/at91sam9261.c | 17 + >> 2 files changed, 757 insertions(+) >> create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi > > [...] > >> + >> + apb { >> + compatible = "simple-bus"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges; >> + >> + tcb0: timer at fffa0000 { >> + compatible = "atmel,at91rm9200-tcb"; >> + reg = <0xfffa0000 0x100>; >> + interrupts = < 17 IRQ_TYPE_LEVEL_HIGH 0 >> + 18 IRQ_TYPE_LEVEL_HIGH 0 >> + 19 IRQ_TYPE_LEVEL_HIGH 0 >> + >; >> + clocks = <&tc0_clk>, <&tc1_clk>, <&tc2_clk>; >> + clock-names = "t0_clk", "t1_clk", "t2_clk"; >> + }; >> + >> + usb1: gadget at fffa4000 { >> + compatible = "atmel,at91rm9200-udc"; >> + reg = <0xfffa4000 0x4000>; >> + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>; >> + clocks = <&usb>, <&udc_clk>, <&udpck>; >> + clock-names = "usb_clk", "udc_clk", "udpck"; >> + status = "disabled"; >> + }; >> + >> + mmc0: mmc at fffa8000 { >> + compatible = "atmel,hsmci"; >> + reg = <0xfffa8000 0x600>; >> + interrupts = <9 IRQ_TYPE_LEVEL_HIGH 0>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_mmc0_clk>, <&pinctrl_mmc0_slot0_cmd_dat0>, <&pinctrl_mmc0_slot0_dat1_3>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + clocks = <&mci0_clk>; >> + clock-names = "mci_clk"; >> + status = "disabled"; >> + }; >> + >> + i2c0: i2c at fffac000 { >> + compatible = "atmel,at91sam9261-i2c"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_i2c_twi>; >> + reg = <0xfffac000 0x100>; >> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + clocks = <&twi0_clk>; >> + status = "disabled"; >> + }; >> + >> + usart0: serial at fffb0000 { >> + compatible = "atmel,at91sam9260-usart"; >> + reg = <0xfffb0000 0x200>; >> + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>; >> + atmel,use-dma-rx; >> + atmel,use-dma-tx; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_usart0>; >> + clocks = <&usart0_clk>; >> + clock-names = "usart"; >> + status = "disabled"; >> + }; >> + >> + usart1: serial at fffb4000 { >> + compatible = "atmel,at91sam9260-usart"; >> + reg = <0xfffb4000 0x200>; >> + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>; >> + atmel,use-dma-rx; >> + atmel,use-dma-tx; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_usart1>; >> + clocks = <&usart1_clk>; >> + clock-names = "usart"; >> + status = "disabled"; >> + }; >> + >> + usart2: serial at fffb8000{ >> + compatible = "atmel,at91sam9260-usart"; >> + reg = <0xfffb8000 0x200>; >> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>; >> + atmel,use-dma-rx; >> + atmel,use-dma-tx; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_usart2>; >> + clocks = <&usart2_clk>; >> + clock-names = "usart"; >> + status = "disabled"; >> + }; >> + >> + ssc0: ssc at fffbc000 { >> + compatible = "atmel,at91rm9200-ssc"; >> + reg = <0xfffbc000 0x4000>; >> + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; >> + status = "disabled"; >> + }; >> + >> + ssc1: ssc at fffc0000 { >> + compatible = "atmel,at91rm9200-ssc"; >> + reg = <0xfffc0000 0x4000>; >> + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; >> + status = "disabled"; >> + }; >> + >> + spi0: spi at fffc8000 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "atmel,at91rm9200-spi"; >> + reg = <0xfffc8000 0x200>; >> + cs-gpios = <0>, <0>, <0>, <0>; >> + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 3>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_spi0>; >> + clocks = <&spi0_clk>; >> + clock-names = "spi_clk"; >> + status = "disabled"; >> + }; >> + >> + spi1: spi at fffcc000 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "atmel,at91rm9200-spi"; >> + reg = <0xfffcc000 0x200>; >> + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_spi1>; >> + clocks = <&spi1_clk>; >> + clock-names = "spi_clk"; >> + status = "disabled"; >> + }; >> + >> + ramc: ramc at ffffea00 { >> + compatible = "atmel,at91sam9260-sdramc"; >> + reg = <0xffffea00 0x200>; >> + }; >> + > > You probably copied/pasted it but according to the block diagram, the > sdram controller is not under the apb. You're right I copied/pasted :o) But the addresses of the registers look like typical APB addresses. AFAIK all the registers of this SOC are accessed through the APB (except for OHCI and LCDC) So probably the real question here is what is the sense of the bus hierarchy in cases where a controller is connected to several buses (APB for registers, AHB/matrix for other purpose) ? As I don't have any idea on how to handle this, I choose to copy/paste. > >> + matrix: matrix at ffffee00 { >> + compatible = "atmel,at91sam9261-bus-matrix"; >> + reg = <0xffffee00 0x200>; >> + }; >> + > > Same here, the apb is actually under the bus matrix. > > I don't know whether it can be represented another way though. > > > -- > Alexandre Belloni, Free Electrons > Embedded Linux, Kernel and Android engineering > http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [PATCH v4 3/8] at91: dt: Add at91sam9261 dt SoC support 2014-02-12 19:47 ` Jean-Jacques Hiblot @ 2014-02-13 8:10 ` Nicolas Ferre -1 siblings, 0 replies; 54+ messages in thread From: Nicolas Ferre @ 2014-02-13 8:10 UTC (permalink / raw) To: Jean-Jacques Hiblot, Alexandre Belloni Cc: Jean-Christophe PLAGNIOL-VILLARD, boris brezillon, Gregory CLEMENT, Linux Kernel Mailing List, linux-arm-kernel On 12/02/2014 20:47, Jean-Jacques Hiblot : > Hi Alexandre, > > 2014-02-12 18:28 GMT+01:00 Alexandre Belloni > <alexandre.belloni@free-electrons.com>: >> Hi, >> >> On 12/02/2014 at 11:06:42 +0100, Jean-Jacques Hiblot wrote : >>> This patch adds support for the Device Tree on a sam9261-based platform >>> >>> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> >>> --- >>> arch/arm/boot/dts/at91sam9261.dtsi | 740 +++++++++++++++++++++++++++++++++++++ >>> arch/arm/mach-at91/at91sam9261.c | 17 + >>> 2 files changed, 757 insertions(+) >>> create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi >> >> [...] >> >>> + >>> + apb { >>> + compatible = "simple-bus"; >>> + #address-cells = <1>; >>> + #size-cells = <1>; >>> + ranges; >>> + >>> + tcb0: timer@fffa0000 { >>> + compatible = "atmel,at91rm9200-tcb"; >>> + reg = <0xfffa0000 0x100>; >>> + interrupts = < 17 IRQ_TYPE_LEVEL_HIGH 0 >>> + 18 IRQ_TYPE_LEVEL_HIGH 0 >>> + 19 IRQ_TYPE_LEVEL_HIGH 0 >>> + >; >>> + clocks = <&tc0_clk>, <&tc1_clk>, <&tc2_clk>; >>> + clock-names = "t0_clk", "t1_clk", "t2_clk"; >>> + }; >>> + >>> + usb1: gadget@fffa4000 { >>> + compatible = "atmel,at91rm9200-udc"; >>> + reg = <0xfffa4000 0x4000>; >>> + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>; >>> + clocks = <&usb>, <&udc_clk>, <&udpck>; >>> + clock-names = "usb_clk", "udc_clk", "udpck"; >>> + status = "disabled"; >>> + }; >>> + >>> + mmc0: mmc@fffa8000 { >>> + compatible = "atmel,hsmci"; >>> + reg = <0xfffa8000 0x600>; >>> + interrupts = <9 IRQ_TYPE_LEVEL_HIGH 0>; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_mmc0_clk>, <&pinctrl_mmc0_slot0_cmd_dat0>, <&pinctrl_mmc0_slot0_dat1_3>; >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + clocks = <&mci0_clk>; >>> + clock-names = "mci_clk"; >>> + status = "disabled"; >>> + }; >>> + >>> + i2c0: i2c@fffac000 { >>> + compatible = "atmel,at91sam9261-i2c"; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_i2c_twi>; >>> + reg = <0xfffac000 0x100>; >>> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>; >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + clocks = <&twi0_clk>; >>> + status = "disabled"; >>> + }; >>> + >>> + usart0: serial@fffb0000 { >>> + compatible = "atmel,at91sam9260-usart"; >>> + reg = <0xfffb0000 0x200>; >>> + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>; >>> + atmel,use-dma-rx; >>> + atmel,use-dma-tx; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_usart0>; >>> + clocks = <&usart0_clk>; >>> + clock-names = "usart"; >>> + status = "disabled"; >>> + }; >>> + >>> + usart1: serial@fffb4000 { >>> + compatible = "atmel,at91sam9260-usart"; >>> + reg = <0xfffb4000 0x200>; >>> + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>; >>> + atmel,use-dma-rx; >>> + atmel,use-dma-tx; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_usart1>; >>> + clocks = <&usart1_clk>; >>> + clock-names = "usart"; >>> + status = "disabled"; >>> + }; >>> + >>> + usart2: serial@fffb8000{ >>> + compatible = "atmel,at91sam9260-usart"; >>> + reg = <0xfffb8000 0x200>; >>> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>; >>> + atmel,use-dma-rx; >>> + atmel,use-dma-tx; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_usart2>; >>> + clocks = <&usart2_clk>; >>> + clock-names = "usart"; >>> + status = "disabled"; >>> + }; >>> + >>> + ssc0: ssc@fffbc000 { >>> + compatible = "atmel,at91rm9200-ssc"; >>> + reg = <0xfffbc000 0x4000>; >>> + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; >>> + status = "disabled"; >>> + }; >>> + >>> + ssc1: ssc@fffc0000 { >>> + compatible = "atmel,at91rm9200-ssc"; >>> + reg = <0xfffc0000 0x4000>; >>> + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; >>> + status = "disabled"; >>> + }; >>> + >>> + spi0: spi@fffc8000 { >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + compatible = "atmel,at91rm9200-spi"; >>> + reg = <0xfffc8000 0x200>; >>> + cs-gpios = <0>, <0>, <0>, <0>; >>> + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 3>; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_spi0>; >>> + clocks = <&spi0_clk>; >>> + clock-names = "spi_clk"; >>> + status = "disabled"; >>> + }; >>> + >>> + spi1: spi@fffcc000 { >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + compatible = "atmel,at91rm9200-spi"; >>> + reg = <0xfffcc000 0x200>; >>> + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_spi1>; >>> + clocks = <&spi1_clk>; >>> + clock-names = "spi_clk"; >>> + status = "disabled"; >>> + }; >>> + >>> + ramc: ramc@ffffea00 { >>> + compatible = "atmel,at91sam9260-sdramc"; >>> + reg = <0xffffea00 0x200>; >>> + }; >>> + >> >> You probably copied/pasted it but according to the block diagram, the >> sdram controller is not under the apb. > You're right I copied/pasted :o) But the addresses of the registers > look like typical APB addresses. > AFAIK all the registers of this SOC are accessed through the APB > (except for OHCI and LCDC) Yes, that is the point: if the register bank appears as an APB address, I place it on the APB bus. The other master interfaces (on AHB) are the ones that the IP uses, not us from the CPU point of view... So I think that Jean-Jacques DT is okay concerning this. > So probably the real question here is what is the sense of the bus > hierarchy in cases where a controller is connected to several buses > (APB for registers, AHB/matrix for other purpose) ? > As I don't have any idea on how to handle this, I choose to copy/paste. > >> >>> + matrix: matrix@ffffee00 { >>> + compatible = "atmel,at91sam9261-bus-matrix"; >>> + reg = <0xffffee00 0x200>; >>> + }; >>> + >> >> Same here, the apb is actually under the bus matrix. >> >> I don't know whether it can be represented another way though. >> >> >> -- >> Alexandre Belloni, Free Electrons >> Embedded Linux, Kernel and Android engineering >> http://free-electrons.com > > -- Nicolas Ferre ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 3/8] at91: dt: Add at91sam9261 dt SoC support @ 2014-02-13 8:10 ` Nicolas Ferre 0 siblings, 0 replies; 54+ messages in thread From: Nicolas Ferre @ 2014-02-13 8:10 UTC (permalink / raw) To: linux-arm-kernel On 12/02/2014 20:47, Jean-Jacques Hiblot : > Hi Alexandre, > > 2014-02-12 18:28 GMT+01:00 Alexandre Belloni > <alexandre.belloni@free-electrons.com>: >> Hi, >> >> On 12/02/2014 at 11:06:42 +0100, Jean-Jacques Hiblot wrote : >>> This patch adds support for the Device Tree on a sam9261-based platform >>> >>> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> >>> --- >>> arch/arm/boot/dts/at91sam9261.dtsi | 740 +++++++++++++++++++++++++++++++++++++ >>> arch/arm/mach-at91/at91sam9261.c | 17 + >>> 2 files changed, 757 insertions(+) >>> create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi >> >> [...] >> >>> + >>> + apb { >>> + compatible = "simple-bus"; >>> + #address-cells = <1>; >>> + #size-cells = <1>; >>> + ranges; >>> + >>> + tcb0: timer at fffa0000 { >>> + compatible = "atmel,at91rm9200-tcb"; >>> + reg = <0xfffa0000 0x100>; >>> + interrupts = < 17 IRQ_TYPE_LEVEL_HIGH 0 >>> + 18 IRQ_TYPE_LEVEL_HIGH 0 >>> + 19 IRQ_TYPE_LEVEL_HIGH 0 >>> + >; >>> + clocks = <&tc0_clk>, <&tc1_clk>, <&tc2_clk>; >>> + clock-names = "t0_clk", "t1_clk", "t2_clk"; >>> + }; >>> + >>> + usb1: gadget at fffa4000 { >>> + compatible = "atmel,at91rm9200-udc"; >>> + reg = <0xfffa4000 0x4000>; >>> + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>; >>> + clocks = <&usb>, <&udc_clk>, <&udpck>; >>> + clock-names = "usb_clk", "udc_clk", "udpck"; >>> + status = "disabled"; >>> + }; >>> + >>> + mmc0: mmc at fffa8000 { >>> + compatible = "atmel,hsmci"; >>> + reg = <0xfffa8000 0x600>; >>> + interrupts = <9 IRQ_TYPE_LEVEL_HIGH 0>; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_mmc0_clk>, <&pinctrl_mmc0_slot0_cmd_dat0>, <&pinctrl_mmc0_slot0_dat1_3>; >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + clocks = <&mci0_clk>; >>> + clock-names = "mci_clk"; >>> + status = "disabled"; >>> + }; >>> + >>> + i2c0: i2c at fffac000 { >>> + compatible = "atmel,at91sam9261-i2c"; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_i2c_twi>; >>> + reg = <0xfffac000 0x100>; >>> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>; >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + clocks = <&twi0_clk>; >>> + status = "disabled"; >>> + }; >>> + >>> + usart0: serial at fffb0000 { >>> + compatible = "atmel,at91sam9260-usart"; >>> + reg = <0xfffb0000 0x200>; >>> + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>; >>> + atmel,use-dma-rx; >>> + atmel,use-dma-tx; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_usart0>; >>> + clocks = <&usart0_clk>; >>> + clock-names = "usart"; >>> + status = "disabled"; >>> + }; >>> + >>> + usart1: serial at fffb4000 { >>> + compatible = "atmel,at91sam9260-usart"; >>> + reg = <0xfffb4000 0x200>; >>> + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>; >>> + atmel,use-dma-rx; >>> + atmel,use-dma-tx; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_usart1>; >>> + clocks = <&usart1_clk>; >>> + clock-names = "usart"; >>> + status = "disabled"; >>> + }; >>> + >>> + usart2: serial at fffb8000{ >>> + compatible = "atmel,at91sam9260-usart"; >>> + reg = <0xfffb8000 0x200>; >>> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>; >>> + atmel,use-dma-rx; >>> + atmel,use-dma-tx; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_usart2>; >>> + clocks = <&usart2_clk>; >>> + clock-names = "usart"; >>> + status = "disabled"; >>> + }; >>> + >>> + ssc0: ssc at fffbc000 { >>> + compatible = "atmel,at91rm9200-ssc"; >>> + reg = <0xfffbc000 0x4000>; >>> + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; >>> + status = "disabled"; >>> + }; >>> + >>> + ssc1: ssc at fffc0000 { >>> + compatible = "atmel,at91rm9200-ssc"; >>> + reg = <0xfffc0000 0x4000>; >>> + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; >>> + status = "disabled"; >>> + }; >>> + >>> + spi0: spi at fffc8000 { >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + compatible = "atmel,at91rm9200-spi"; >>> + reg = <0xfffc8000 0x200>; >>> + cs-gpios = <0>, <0>, <0>, <0>; >>> + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 3>; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_spi0>; >>> + clocks = <&spi0_clk>; >>> + clock-names = "spi_clk"; >>> + status = "disabled"; >>> + }; >>> + >>> + spi1: spi at fffcc000 { >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + compatible = "atmel,at91rm9200-spi"; >>> + reg = <0xfffcc000 0x200>; >>> + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pinctrl_spi1>; >>> + clocks = <&spi1_clk>; >>> + clock-names = "spi_clk"; >>> + status = "disabled"; >>> + }; >>> + >>> + ramc: ramc at ffffea00 { >>> + compatible = "atmel,at91sam9260-sdramc"; >>> + reg = <0xffffea00 0x200>; >>> + }; >>> + >> >> You probably copied/pasted it but according to the block diagram, the >> sdram controller is not under the apb. > You're right I copied/pasted :o) But the addresses of the registers > look like typical APB addresses. > AFAIK all the registers of this SOC are accessed through the APB > (except for OHCI and LCDC) Yes, that is the point: if the register bank appears as an APB address, I place it on the APB bus. The other master interfaces (on AHB) are the ones that the IP uses, not us from the CPU point of view... So I think that Jean-Jacques DT is okay concerning this. > So probably the real question here is what is the sense of the bus > hierarchy in cases where a controller is connected to several buses > (APB for registers, AHB/matrix for other purpose) ? > As I don't have any idea on how to handle this, I choose to copy/paste. > >> >>> + matrix: matrix at ffffee00 { >>> + compatible = "atmel,at91sam9261-bus-matrix"; >>> + reg = <0xffffee00 0x200>; >>> + }; >>> + >> >> Same here, the apb is actually under the bus matrix. >> >> I don't know whether it can be represented another way though. >> >> >> -- >> Alexandre Belloni, Free Electrons >> Embedded Linux, Kernel and Android engineering >> http://free-electrons.com > > -- Nicolas Ferre ^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [PATCH v4 3/8] at91: dt: Add at91sam9261 dt SoC support 2014-02-13 8:10 ` Nicolas Ferre @ 2014-02-13 8:54 ` Alexandre Belloni -1 siblings, 0 replies; 54+ messages in thread From: Alexandre Belloni @ 2014-02-13 8:54 UTC (permalink / raw) To: Nicolas Ferre Cc: Jean-Jacques Hiblot, Jean-Christophe PLAGNIOL-VILLARD, boris brezillon, Gregory CLEMENT, Linux Kernel Mailing List, linux-arm-kernel On 13/02/2014 at 09:10:54 +0100, Nicolas Ferre wrote : > On 12/02/2014 20:47, Jean-Jacques Hiblot : > >> > >> You probably copied/pasted it but according to the block diagram, the > >> sdram controller is not under the apb. > > You're right I copied/pasted :o) But the addresses of the registers > > look like typical APB addresses. > > AFAIK all the registers of this SOC are accessed through the APB > > (except for OHCI and LCDC) > > Yes, that is the point: if the register bank appears as an APB address, > I place it on the APB bus. > The other master interfaces (on AHB) are the ones that the IP uses, not > us from the CPU point of view... > > So I think that Jean-Jacques DT is okay concerning this. > Ok, I'm perfectly fine with that. Thanks for the answer ! -- Alexandre Belloni, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 3/8] at91: dt: Add at91sam9261 dt SoC support @ 2014-02-13 8:54 ` Alexandre Belloni 0 siblings, 0 replies; 54+ messages in thread From: Alexandre Belloni @ 2014-02-13 8:54 UTC (permalink / raw) To: linux-arm-kernel On 13/02/2014 at 09:10:54 +0100, Nicolas Ferre wrote : > On 12/02/2014 20:47, Jean-Jacques Hiblot : > >> > >> You probably copied/pasted it but according to the block diagram, the > >> sdram controller is not under the apb. > > You're right I copied/pasted :o) But the addresses of the registers > > look like typical APB addresses. > > AFAIK all the registers of this SOC are accessed through the APB > > (except for OHCI and LCDC) > > Yes, that is the point: if the register bank appears as an APB address, > I place it on the APB bus. > The other master interfaces (on AHB) are the ones that the IP uses, not > us from the CPU point of view... > > So I think that Jean-Jacques DT is okay concerning this. > Ok, I'm perfectly fine with that. Thanks for the answer ! -- Alexandre Belloni, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [PATCH v4 3/8] at91: dt: Add at91sam9261 dt SoC support 2014-02-12 10:06 ` Jean-Jacques Hiblot @ 2014-02-12 21:04 ` Alexandre Belloni -1 siblings, 0 replies; 54+ messages in thread From: Alexandre Belloni @ 2014-02-12 21:04 UTC (permalink / raw) To: Jean-Jacques Hiblot Cc: nicolas.ferre, plagnioj, b.brezillon, gregory.clement, linux-kernel, linux-arm-kernel Sorry, one more comment on that patch: On 12/02/2014 at 11:06:42 +0100, Jean-Jacques Hiblot wrote : > + pinctrl@fffff400 { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; > + ranges = <0xfffff400 0xfffff400 0xa00>; > + I believe you got the range wrong, shouldn't it be: ranges = <0xfffff400 0xfffff400 0x600>; -- Alexandre Belloni, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 3/8] at91: dt: Add at91sam9261 dt SoC support @ 2014-02-12 21:04 ` Alexandre Belloni 0 siblings, 0 replies; 54+ messages in thread From: Alexandre Belloni @ 2014-02-12 21:04 UTC (permalink / raw) To: linux-arm-kernel Sorry, one more comment on that patch: On 12/02/2014 at 11:06:42 +0100, Jean-Jacques Hiblot wrote : > + pinctrl at fffff400 { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; > + ranges = <0xfffff400 0xfffff400 0xa00>; > + I believe you got the range wrong, shouldn't it be: ranges = <0xfffff400 0xfffff400 0x600>; -- Alexandre Belloni, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [PATCH v4 3/8] at91: dt: Add at91sam9261 dt SoC support 2014-02-12 21:04 ` Alexandre Belloni @ 2014-02-13 6:11 ` Jean-Jacques Hiblot -1 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-13 6:11 UTC (permalink / raw) To: Alexandre Belloni Cc: Jean-Jacques Hiblot, Nicolas Ferre, Jean-Christophe PLAGNIOL-VILLARD, boris brezillon, Gregory CLEMENT, Linux Kernel Mailing List, linux-arm-kernel 2014-02-12 22:04 GMT+01:00 Alexandre Belloni <alexandre.belloni@free-electrons.com>: > Sorry, one more comment on that patch: > > On 12/02/2014 at 11:06:42 +0100, Jean-Jacques Hiblot wrote : >> + pinctrl@fffff400 { >> + #address-cells = <1>; >> + #size-cells = <1>; >> + compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; >> + ranges = <0xfffff400 0xfffff400 0xa00>; >> + > I believe you got the range wrong, shouldn't it be: > ranges = <0xfffff400 0xfffff400 0x600>; > Yes you're right. Thanks for the review > > -- > Alexandre Belloni, Free Electrons > Embedded Linux, Kernel and Android engineering > http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 3/8] at91: dt: Add at91sam9261 dt SoC support @ 2014-02-13 6:11 ` Jean-Jacques Hiblot 0 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-13 6:11 UTC (permalink / raw) To: linux-arm-kernel 2014-02-12 22:04 GMT+01:00 Alexandre Belloni <alexandre.belloni@free-electrons.com>: > Sorry, one more comment on that patch: > > On 12/02/2014 at 11:06:42 +0100, Jean-Jacques Hiblot wrote : >> + pinctrl at fffff400 { >> + #address-cells = <1>; >> + #size-cells = <1>; >> + compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; >> + ranges = <0xfffff400 0xfffff400 0xa00>; >> + > I believe you got the range wrong, shouldn't it be: > ranges = <0xfffff400 0xfffff400 0x600>; > Yes you're right. Thanks for the review > > -- > Alexandre Belloni, Free Electrons > Embedded Linux, Kernel and Android engineering > http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 4/8] at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs 2014-02-12 10:06 ` Jean-Jacques Hiblot @ 2014-02-12 10:06 ` Jean-Jacques Hiblot -1 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: nicolas.ferre, plagnioj, b.brezillon Cc: linux-kernel, linux-arm-kernel, gregory.clement, Jean-Jacques Hiblot Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> --- arch/arm/configs/at91_dt_defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/configs/at91_dt_defconfig b/arch/arm/configs/at91_dt_defconfig index 0b4e9b5..3c6905d 100644 --- a/arch/arm/configs/at91_dt_defconfig +++ b/arch/arm/configs/at91_dt_defconfig @@ -16,6 +16,7 @@ CONFIG_MODULE_UNLOAD=y CONFIG_ARCH_AT91=y CONFIG_SOC_AT91RM9200=y CONFIG_SOC_AT91SAM9260=y +CONFIG_SOC_AT91SAM9261=y CONFIG_SOC_AT91SAM9263=y CONFIG_SOC_AT91SAM9G45=y CONFIG_SOC_AT91SAM9X5=y -- 1.8.5.3 ^ permalink raw reply related [flat|nested] 54+ messages in thread
* [PATCH v4 4/8] at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs @ 2014-02-12 10:06 ` Jean-Jacques Hiblot 0 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: linux-arm-kernel Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> --- arch/arm/configs/at91_dt_defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/configs/at91_dt_defconfig b/arch/arm/configs/at91_dt_defconfig index 0b4e9b5..3c6905d 100644 --- a/arch/arm/configs/at91_dt_defconfig +++ b/arch/arm/configs/at91_dt_defconfig @@ -16,6 +16,7 @@ CONFIG_MODULE_UNLOAD=y CONFIG_ARCH_AT91=y CONFIG_SOC_AT91RM9200=y CONFIG_SOC_AT91SAM9260=y +CONFIG_SOC_AT91SAM9261=y CONFIG_SOC_AT91SAM9263=y CONFIG_SOC_AT91SAM9G45=y CONFIG_SOC_AT91SAM9X5=y -- 1.8.5.3 ^ permalink raw reply related [flat|nested] 54+ messages in thread
* [PATCH v4 5/8] at91: dt: sam9261: Device Tree support for the at91sam9261ek 2014-02-12 10:06 ` Jean-Jacques Hiblot @ 2014-02-12 10:06 ` Jean-Jacques Hiblot -1 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: nicolas.ferre, plagnioj, b.brezillon Cc: linux-kernel, linux-arm-kernel, gregory.clement, Jean-Jacques Hiblot This patch implements a DTS to boot a at91sam9261ek with a dt-enabled kernel (at91_dt_defconfig). supported features are: * dbgu * lcdc * usb host * usb gadget, * spi dataflash * nand flash * touchscreen * leds * user buttons In the TODO list: * dm9000 (ethernet) * audio * mmc Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> --- arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/at91sam9261ek.dts | 204 ++++++++++++++++++++++++++++++++++++ 2 files changed, 206 insertions(+) create mode 100644 arch/arm/boot/dts/at91sam9261ek.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index b9d6a8b..493082b 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -12,6 +12,8 @@ dtb-$(CONFIG_ARCH_AT91) += ethernut5.dtb dtb-$(CONFIG_ARCH_AT91) += evk-pro3.dtb dtb-$(CONFIG_ARCH_AT91) += tny_a9260.dtb dtb-$(CONFIG_ARCH_AT91) += usb_a9260.dtb +# sam9261 +dtb-$(CONFIG_ARCH_AT91) += at91sam9261ek.dtb # sam9263 dtb-$(CONFIG_ARCH_AT91) += at91sam9263ek.dtb dtb-$(CONFIG_ARCH_AT91) += tny_a9263.dtb diff --git a/arch/arm/boot/dts/at91sam9261ek.dts b/arch/arm/boot/dts/at91sam9261ek.dts new file mode 100644 index 0000000..03adb7f --- /dev/null +++ b/arch/arm/boot/dts/at91sam9261ek.dts @@ -0,0 +1,204 @@ +/* + * at91sam9261ek.dts - Device Tree file for Atmel at91sam9261 reference board + * + * Copyright (C) 2013 Jean-Jacques Hiblot <jjhiblot@traphandler.com> + * + * Licensed under GPLv2 only. + */ +/dts-v1/; +#include "at91sam9261.dtsi" + +/ { + model = "Atmel at91sam9261ek"; + compatible = "atmel,at91sam9261ek", "atmel,at91sam9261", "atmel,at91sam9"; + + chosen { + bootargs = "console=ttyS0,115200 rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs rw"; + }; + + memory { + reg = <0x20000000 0x4000000>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <18432000>; + }; + }; + + ahb { + usb0: ohci@00500000 { + status = "okay"; + }; + + fb0: fb@0x00600000 { + display = <&display0>; + atmel,power-control-gpio = <&pioA 12 GPIO_ACTIVE_LOW>; + status = "okay"; + + display0: display { + bits-per-pixel = <16>; + atmel,lcdcon-backlight; + atmel,dmacon = <0x1>; + atmel,lcdcon2 = <0x80008002>; + atmel,guard-time = <1>; + atmel,lcd-wiring-mode = "BRG"; + + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <4965000>; + hactive = <240>; + vactive = <320>; + hback-porch = <1>; + hfront-porch = <33>; + vback-porch = <1>; + vfront-porch = <0>; + hsync-len = <5>; + vsync-len = <1>; + hsync-active = <1>; + vsync-active = <1>; + }; + }; + }; + }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + at91bootstrap@0 { + label = "at91bootstrap"; + reg = <0x0 0x40000>; + }; + + bootloader@40000 { + label = "bootloader"; + reg = <0x40000 0x80000>; + }; + + bootloaderenv@c0000 { + label = "bootloader env"; + reg = <0xc0000 0xc0000>; + }; + + dtb@180000 { + label = "device tree"; + reg = <0x180000 0x80000>; + }; + + kernel@200000 { + label = "kernel"; + reg = <0x200000 0x600000>; + }; + + rootfs@800000 { + label = "rootfs"; + reg = <0x800000 0x0f800000>; + }; + }; + + apb { + usb1: gadget@fffa4000 { + atmel,vbus-gpio = <&pioB 29 GPIO_ACTIVE_HIGH>; + status = "okay"; + }; + spi0: spi@fffc8000 { + cs-gpios = <&pioA 3 0>, <0>, <&pioA 28 0>, <0>; + status = "okay"; + + mtd_dataflash@0 { + compatible = "atmel,at45", "atmel,dataflash"; + reg = <0>; + spi-max-frequency = <15000000>; + }; + tsc2046@0 { + reg = <2>; + compatible = "ti,ads7843"; + interrupts-extended = <&pioC 2 IRQ_TYPE_EDGE_BOTH>; + spi-max-frequency = <3000000>; + pendown-gpio = <&pioC 2 GPIO_ACTIVE_HIGH>; + + ti,x-min = /bits/ 16 <150>; + ti,x-max = /bits/ 16 <3830>; + ti,y-min = /bits/ 16 <190>; + ti,y-max = /bits/ 16 <3830>; + ti,vref-delay-usecs = /bits/ 16 <450>; + ti,x-plate-ohms = /bits/ 16 <450>; + ti,y-plate-ohms = /bits/ 16 <250>; + ti,pressure-max = /bits/ 16 <15000>; + ti,debounce-rep = /bits/ 16 <0>; + ti,debounce-tol = /bits/ 16 <65535>; + ti,debounce-max = /bits/ 16 <1>; + + linux,wakeup; + }; + }; + + dbgu: serial@fffff200 { + status = "okay"; + }; + + watchdog@fffffd40 { + status = "okay"; + }; + + }; + }; + + leds { + compatible = "gpio-leds"; + + ds8 { + label = "ds8"; + gpios = <&pioA 13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "none"; + }; + ds7 { + label = "ds7"; + gpios = <&pioA 14 GPIO_ACTIVE_LOW>; + linux,default-trigger = "nand-disk"; + }; + ds1 { + label = "ds1"; + gpios = <&pioA 23 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + button_0 { + label = "button_0"; + gpios = <&pioA 27 GPIO_ACTIVE_LOW>; + linux,code = <256>; + gpio-key,wakeup; + }; + button_1 { + label = "button_1"; + gpios = <&pioA 26 GPIO_ACTIVE_LOW>; + linux,code = <257>; + gpio-key,wakeup; + }; + button_2 { + label = "button_2"; + gpios = <&pioA 25 GPIO_ACTIVE_LOW>; + linux,code = <258>; + gpio-key,wakeup; + }; + button_3 { + label = "button_3"; + gpios = <&pioA 24 GPIO_ACTIVE_LOW>; + linux,code = <259>; + gpio-key,wakeup; + }; + }; +}; -- 1.8.5.3 ^ permalink raw reply related [flat|nested] 54+ messages in thread
* [PATCH v4 5/8] at91: dt: sam9261: Device Tree support for the at91sam9261ek @ 2014-02-12 10:06 ` Jean-Jacques Hiblot 0 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: linux-arm-kernel This patch implements a DTS to boot a at91sam9261ek with a dt-enabled kernel (at91_dt_defconfig). supported features are: * dbgu * lcdc * usb host * usb gadget, * spi dataflash * nand flash * touchscreen * leds * user buttons In the TODO list: * dm9000 (ethernet) * audio * mmc Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> --- arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/at91sam9261ek.dts | 204 ++++++++++++++++++++++++++++++++++++ 2 files changed, 206 insertions(+) create mode 100644 arch/arm/boot/dts/at91sam9261ek.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index b9d6a8b..493082b 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -12,6 +12,8 @@ dtb-$(CONFIG_ARCH_AT91) += ethernut5.dtb dtb-$(CONFIG_ARCH_AT91) += evk-pro3.dtb dtb-$(CONFIG_ARCH_AT91) += tny_a9260.dtb dtb-$(CONFIG_ARCH_AT91) += usb_a9260.dtb +# sam9261 +dtb-$(CONFIG_ARCH_AT91) += at91sam9261ek.dtb # sam9263 dtb-$(CONFIG_ARCH_AT91) += at91sam9263ek.dtb dtb-$(CONFIG_ARCH_AT91) += tny_a9263.dtb diff --git a/arch/arm/boot/dts/at91sam9261ek.dts b/arch/arm/boot/dts/at91sam9261ek.dts new file mode 100644 index 0000000..03adb7f --- /dev/null +++ b/arch/arm/boot/dts/at91sam9261ek.dts @@ -0,0 +1,204 @@ +/* + * at91sam9261ek.dts - Device Tree file for Atmel at91sam9261 reference board + * + * Copyright (C) 2013 Jean-Jacques Hiblot <jjhiblot@traphandler.com> + * + * Licensed under GPLv2 only. + */ +/dts-v1/; +#include "at91sam9261.dtsi" + +/ { + model = "Atmel at91sam9261ek"; + compatible = "atmel,at91sam9261ek", "atmel,at91sam9261", "atmel,at91sam9"; + + chosen { + bootargs = "console=ttyS0,115200 rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs rw"; + }; + + memory { + reg = <0x20000000 0x4000000>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock at 0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <18432000>; + }; + }; + + ahb { + usb0: ohci at 00500000 { + status = "okay"; + }; + + fb0: fb at 0x00600000 { + display = <&display0>; + atmel,power-control-gpio = <&pioA 12 GPIO_ACTIVE_LOW>; + status = "okay"; + + display0: display { + bits-per-pixel = <16>; + atmel,lcdcon-backlight; + atmel,dmacon = <0x1>; + atmel,lcdcon2 = <0x80008002>; + atmel,guard-time = <1>; + atmel,lcd-wiring-mode = "BRG"; + + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <4965000>; + hactive = <240>; + vactive = <320>; + hback-porch = <1>; + hfront-porch = <33>; + vback-porch = <1>; + vfront-porch = <0>; + hsync-len = <5>; + vsync-len = <1>; + hsync-active = <1>; + vsync-active = <1>; + }; + }; + }; + }; + + nand0: nand at 40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + at91bootstrap at 0 { + label = "at91bootstrap"; + reg = <0x0 0x40000>; + }; + + bootloader at 40000 { + label = "bootloader"; + reg = <0x40000 0x80000>; + }; + + bootloaderenv at c0000 { + label = "bootloader env"; + reg = <0xc0000 0xc0000>; + }; + + dtb at 180000 { + label = "device tree"; + reg = <0x180000 0x80000>; + }; + + kernel at 200000 { + label = "kernel"; + reg = <0x200000 0x600000>; + }; + + rootfs at 800000 { + label = "rootfs"; + reg = <0x800000 0x0f800000>; + }; + }; + + apb { + usb1: gadget at fffa4000 { + atmel,vbus-gpio = <&pioB 29 GPIO_ACTIVE_HIGH>; + status = "okay"; + }; + spi0: spi at fffc8000 { + cs-gpios = <&pioA 3 0>, <0>, <&pioA 28 0>, <0>; + status = "okay"; + + mtd_dataflash at 0 { + compatible = "atmel,at45", "atmel,dataflash"; + reg = <0>; + spi-max-frequency = <15000000>; + }; + tsc2046 at 0 { + reg = <2>; + compatible = "ti,ads7843"; + interrupts-extended = <&pioC 2 IRQ_TYPE_EDGE_BOTH>; + spi-max-frequency = <3000000>; + pendown-gpio = <&pioC 2 GPIO_ACTIVE_HIGH>; + + ti,x-min = /bits/ 16 <150>; + ti,x-max = /bits/ 16 <3830>; + ti,y-min = /bits/ 16 <190>; + ti,y-max = /bits/ 16 <3830>; + ti,vref-delay-usecs = /bits/ 16 <450>; + ti,x-plate-ohms = /bits/ 16 <450>; + ti,y-plate-ohms = /bits/ 16 <250>; + ti,pressure-max = /bits/ 16 <15000>; + ti,debounce-rep = /bits/ 16 <0>; + ti,debounce-tol = /bits/ 16 <65535>; + ti,debounce-max = /bits/ 16 <1>; + + linux,wakeup; + }; + }; + + dbgu: serial at fffff200 { + status = "okay"; + }; + + watchdog at fffffd40 { + status = "okay"; + }; + + }; + }; + + leds { + compatible = "gpio-leds"; + + ds8 { + label = "ds8"; + gpios = <&pioA 13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "none"; + }; + ds7 { + label = "ds7"; + gpios = <&pioA 14 GPIO_ACTIVE_LOW>; + linux,default-trigger = "nand-disk"; + }; + ds1 { + label = "ds1"; + gpios = <&pioA 23 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + button_0 { + label = "button_0"; + gpios = <&pioA 27 GPIO_ACTIVE_LOW>; + linux,code = <256>; + gpio-key,wakeup; + }; + button_1 { + label = "button_1"; + gpios = <&pioA 26 GPIO_ACTIVE_LOW>; + linux,code = <257>; + gpio-key,wakeup; + }; + button_2 { + label = "button_2"; + gpios = <&pioA 25 GPIO_ACTIVE_LOW>; + linux,code = <258>; + gpio-key,wakeup; + }; + button_3 { + label = "button_3"; + gpios = <&pioA 24 GPIO_ACTIVE_LOW>; + linux,code = <259>; + gpio-key,wakeup; + }; + }; +}; -- 1.8.5.3 ^ permalink raw reply related [flat|nested] 54+ messages in thread
* [PATCH v4 6/8] at91: updated the at91_dt_defconfig with support for the ADS7846 2014-02-12 10:06 ` Jean-Jacques Hiblot @ 2014-02-12 10:06 ` Jean-Jacques Hiblot -1 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: nicolas.ferre, plagnioj, b.brezillon Cc: linux-kernel, linux-arm-kernel, gregory.clement, Jean-Jacques Hiblot This provides touchscreen support to the at91sam9261ek Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> --- arch/arm/configs/at91_dt_defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/configs/at91_dt_defconfig b/arch/arm/configs/at91_dt_defconfig index 3c6905d..aaa322d 100644 --- a/arch/arm/configs/at91_dt_defconfig +++ b/arch/arm/configs/at91_dt_defconfig @@ -120,6 +120,7 @@ CONFIG_INPUT_EVDEV=y CONFIG_KEYBOARD_GPIO=y # CONFIG_INPUT_MOUSE is not set CONFIG_INPUT_TOUCHSCREEN=y +CONFIG_TOUCHSCREEN_ADS7846=y # CONFIG_SERIO is not set CONFIG_LEGACY_PTY_COUNT=4 CONFIG_SERIAL_ATMEL=y -- 1.8.5.3 ^ permalink raw reply related [flat|nested] 54+ messages in thread
* [PATCH v4 6/8] at91: updated the at91_dt_defconfig with support for the ADS7846 @ 2014-02-12 10:06 ` Jean-Jacques Hiblot 0 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: linux-arm-kernel This provides touchscreen support to the at91sam9261ek Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> --- arch/arm/configs/at91_dt_defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/configs/at91_dt_defconfig b/arch/arm/configs/at91_dt_defconfig index 3c6905d..aaa322d 100644 --- a/arch/arm/configs/at91_dt_defconfig +++ b/arch/arm/configs/at91_dt_defconfig @@ -120,6 +120,7 @@ CONFIG_INPUT_EVDEV=y CONFIG_KEYBOARD_GPIO=y # CONFIG_INPUT_MOUSE is not set CONFIG_INPUT_TOUCHSCREEN=y +CONFIG_TOUCHSCREEN_ADS7846=y # CONFIG_SERIO is not set CONFIG_LEGACY_PTY_COUNT=4 CONFIG_SERIAL_ATMEL=y -- 1.8.5.3 ^ permalink raw reply related [flat|nested] 54+ messages in thread
* [PATCH v4 7/8] ARM: at91: prepare common clk transition for sam9261 SoC 2014-02-12 10:06 ` Jean-Jacques Hiblot @ 2014-02-12 10:06 ` Jean-Jacques Hiblot -1 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: nicolas.ferre, plagnioj, b.brezillon Cc: linux-kernel, linux-arm-kernel, gregory.clement, Jean-Jacques Hiblot This patch encloses sam9261 old clk registration in "#if defined(CONFIG_OLD_CLK_AT91) #endif" sections. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> --- arch/arm/mach-at91/at91sam9261.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c index 5c90581..3345a2b 100644 --- a/arch/arm/mach-at91/at91sam9261.c +++ b/arch/arm/mach-at91/at91sam9261.c @@ -25,10 +25,12 @@ #include "at91_rstc.h" #include "soc.h" #include "generic.h" -#include "clock.h" #include "sam9_smc.h" #include "pm.h" +#if defined(CONFIG_OLD_CLK_AT91) +#include "clock.h" + /* -------------------------------------------------------------------- * Clocks * -------------------------------------------------------------------- */ @@ -264,7 +266,9 @@ static void __init at91sam9261_register_clocks(void) clk_register(&hck0); clk_register(&hck1); } - +#else +#define at91sam9261_register_clocks NULL +#endif /* -------------------------------------------------------------------- * GPIO * -------------------------------------------------------------------- */ -- 1.8.5.3 ^ permalink raw reply related [flat|nested] 54+ messages in thread
* [PATCH v4 7/8] ARM: at91: prepare common clk transition for sam9261 SoC @ 2014-02-12 10:06 ` Jean-Jacques Hiblot 0 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: linux-arm-kernel This patch encloses sam9261 old clk registration in "#if defined(CONFIG_OLD_CLK_AT91) #endif" sections. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> --- arch/arm/mach-at91/at91sam9261.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c index 5c90581..3345a2b 100644 --- a/arch/arm/mach-at91/at91sam9261.c +++ b/arch/arm/mach-at91/at91sam9261.c @@ -25,10 +25,12 @@ #include "at91_rstc.h" #include "soc.h" #include "generic.h" -#include "clock.h" #include "sam9_smc.h" #include "pm.h" +#if defined(CONFIG_OLD_CLK_AT91) +#include "clock.h" + /* -------------------------------------------------------------------- * Clocks * -------------------------------------------------------------------- */ @@ -264,7 +266,9 @@ static void __init at91sam9261_register_clocks(void) clk_register(&hck0); clk_register(&hck1); } - +#else +#define at91sam9261_register_clocks NULL +#endif /* -------------------------------------------------------------------- * GPIO * -------------------------------------------------------------------- */ -- 1.8.5.3 ^ permalink raw reply related [flat|nested] 54+ messages in thread
* [PATCH v4 8/8] ARM: at91: move sam9261 SoC to common clk 2014-02-12 10:06 ` Jean-Jacques Hiblot @ 2014-02-12 10:06 ` Jean-Jacques Hiblot -1 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: nicolas.ferre, plagnioj, b.brezillon Cc: linux-kernel, linux-arm-kernel, gregory.clement, Jean-Jacques Hiblot This patch removes the selection of AT91_USE_OLD_CLK when selecting sam9261 SoCs support. This will automatically enable COMMON_CLK_AT91 option and add support for at91 common clk implementation. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> --- arch/arm/mach-at91/Kconfig | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 4f0e800..5af3f07 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -119,7 +119,6 @@ config SOC_AT91SAM9261 select HAVE_AT91_DBGU0 select HAVE_FB_ATMEL select SOC_AT91SAM9 - select AT91_USE_OLD_CLK select HAVE_AT91_USB_CLK help Select this if you are using one of Atmel's AT91SAM9261 or AT91SAM9G10 SoC. -- 1.8.5.3 ^ permalink raw reply related [flat|nested] 54+ messages in thread
* [PATCH v4 8/8] ARM: at91: move sam9261 SoC to common clk @ 2014-02-12 10:06 ` Jean-Jacques Hiblot 0 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 10:06 UTC (permalink / raw) To: linux-arm-kernel This patch removes the selection of AT91_USE_OLD_CLK when selecting sam9261 SoCs support. This will automatically enable COMMON_CLK_AT91 option and add support for at91 common clk implementation. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com> --- arch/arm/mach-at91/Kconfig | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 4f0e800..5af3f07 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -119,7 +119,6 @@ config SOC_AT91SAM9261 select HAVE_AT91_DBGU0 select HAVE_FB_ATMEL select SOC_AT91SAM9 - select AT91_USE_OLD_CLK select HAVE_AT91_USB_CLK help Select this if you are using one of Atmel's AT91SAM9261 or AT91SAM9G10 SoC. -- 1.8.5.3 ^ permalink raw reply related [flat|nested] 54+ messages in thread
* Re: [PATCH v4 0/8] Device Tree support for the at91sam9261ek 2014-02-12 10:06 ` Jean-Jacques Hiblot @ 2014-02-12 11:14 ` Gregory CLEMENT -1 siblings, 0 replies; 54+ messages in thread From: Gregory CLEMENT @ 2014-02-12 11:14 UTC (permalink / raw) To: Jean-Jacques Hiblot, nicolas.ferre, plagnioj, b.brezillon Cc: linux-kernel, linux-arm-kernel Hi Jean-Jacques, On 12/02/2014 11:06, Jean-Jacques Hiblot wrote: > This patch set aims at bringing a device tree support for the sam9261. > It's mostly based on the sam9263 and sam9x5 stuff. > > Changes since V3: > * Added support for the touchscreen > * Added support for the spi dataflash > * Activated the TCB by default > * Reworked the patch organization to reduce the number of patchs > * changed the default bootargs (no mem description, UBI on mtdpart 5) > * Changed the xlate implementation of the at91 pinctrl driver to lock the GPIOs > for IRQs instead of requesting them (needed for the touchscreen driver) > * some stylistic changes > > Changes since V2: > * removed the smc driver from the serie. It'll be posted in an independent > serie later. > * removed the DM9000 support (it'll come with the smc driver) > * the sam9261 now supports the Common Clock Framework (CCF). Note: to enable > the CCF you must remove from the kernel config the platforms that don't > support it. > * Added basic DT binding for the bus matrix > * Added support for USB host > * Added support for USB gadget > * in dts(i), replaced interrupt-parent with interrupts-extended > * changed the nand partition plan (same as for the sama5d3) > * removed 'mem' parameter in command line > * re-ordered dt-nodes in ascending address order. > * split the lcd support patch in 2 parts (SOC and board) > > > Change since V1: > * changed the DT representation to use address translation and separate the > timings' configuration from the device properties by adding a "simple-bus" > inetrmediate node. > * moved the smc driver from drivers/bus to drivers/memmory > * smc driver now accepts timings in nanoseconds as well as raw register values > * smc driver can clip the timings if they're out of bound and dump them to the > console > * DM9000 timings are now described in nanosecs (for the virtue of example) > > supported features are: > * working with the Common Clock Framework and the old at91 clock implementation > * dbgu > * lcdc > * usb host > * usb gadget, > * spi dataflash > * nand flash > * touchscreen > * leds > * user buttons > > In the TODO list: > * dm9000 (ethernet) > * audio > * mmc Besides the my comment on the 1st patch, all this series seems pretty neat for me. It's worth mentioning also that audio and mmc are in the TODO list by lack of hardware to test it. So what I suggest here is to send a follow-up patch set and to ask for a Tested-By from people being able to test it. For dm9000 the issue is (again) related to an ordering problem: the Ethernet need an interrupt provided by the gpio driver. Unfortunately, the gpio driver initialization is called after the dm900 driver initialization. Thanks, Gregory > > This serie relies on the following patchs: > usb: at91-udc: fix irq and iomem resource retrieval > ARM: at91: prepare sam9 dt boards transition to common > > Jean-Jacques > > Jean-Jacques Hiblot (8): > at91: dt: Adds support for the bus matrix declaration in the DT > at91: pinctrl: don't request GPIOs used for interrupts but lock them > as IRQ > at91: dt: Add at91sam9261 dt SoC support > at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs > at91: dt: sam9261: Device Tree support for the at91sam9261ek > at91: updated the at91_dt_defconfig with support for the ADS7846 > ARM: at91: prepare common clk transition for sam9261 SoC > ARM: at91: move sam9261 SoC to common clk > > arch/arm/boot/dts/Makefile | 2 + > arch/arm/boot/dts/at91sam9261.dtsi | 740 ++++++++++++++++++++++++++++++++++++ > arch/arm/boot/dts/at91sam9261ek.dts | 204 ++++++++++ > arch/arm/configs/at91_dt_defconfig | 2 + > arch/arm/mach-at91/Kconfig | 1 - > arch/arm/mach-at91/at91sam9261.c | 25 +- > arch/arm/mach-at91/setup.c | 23 ++ > drivers/pinctrl/pinctrl-at91.c | 5 +- > 8 files changed, 996 insertions(+), 6 deletions(-) > create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi > create mode 100644 arch/arm/boot/dts/at91sam9261ek.dts > -- Gregory Clement, Free Electrons Kernel, drivers, real-time and embedded Linux development, consulting, training and support. http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 0/8] Device Tree support for the at91sam9261ek @ 2014-02-12 11:14 ` Gregory CLEMENT 0 siblings, 0 replies; 54+ messages in thread From: Gregory CLEMENT @ 2014-02-12 11:14 UTC (permalink / raw) To: linux-arm-kernel Hi Jean-Jacques, On 12/02/2014 11:06, Jean-Jacques Hiblot wrote: > This patch set aims at bringing a device tree support for the sam9261. > It's mostly based on the sam9263 and sam9x5 stuff. > > Changes since V3: > * Added support for the touchscreen > * Added support for the spi dataflash > * Activated the TCB by default > * Reworked the patch organization to reduce the number of patchs > * changed the default bootargs (no mem description, UBI on mtdpart 5) > * Changed the xlate implementation of the at91 pinctrl driver to lock the GPIOs > for IRQs instead of requesting them (needed for the touchscreen driver) > * some stylistic changes > > Changes since V2: > * removed the smc driver from the serie. It'll be posted in an independent > serie later. > * removed the DM9000 support (it'll come with the smc driver) > * the sam9261 now supports the Common Clock Framework (CCF). Note: to enable > the CCF you must remove from the kernel config the platforms that don't > support it. > * Added basic DT binding for the bus matrix > * Added support for USB host > * Added support for USB gadget > * in dts(i), replaced interrupt-parent with interrupts-extended > * changed the nand partition plan (same as for the sama5d3) > * removed 'mem' parameter in command line > * re-ordered dt-nodes in ascending address order. > * split the lcd support patch in 2 parts (SOC and board) > > > Change since V1: > * changed the DT representation to use address translation and separate the > timings' configuration from the device properties by adding a "simple-bus" > inetrmediate node. > * moved the smc driver from drivers/bus to drivers/memmory > * smc driver now accepts timings in nanoseconds as well as raw register values > * smc driver can clip the timings if they're out of bound and dump them to the > console > * DM9000 timings are now described in nanosecs (for the virtue of example) > > supported features are: > * working with the Common Clock Framework and the old at91 clock implementation > * dbgu > * lcdc > * usb host > * usb gadget, > * spi dataflash > * nand flash > * touchscreen > * leds > * user buttons > > In the TODO list: > * dm9000 (ethernet) > * audio > * mmc Besides the my comment on the 1st patch, all this series seems pretty neat for me. It's worth mentioning also that audio and mmc are in the TODO list by lack of hardware to test it. So what I suggest here is to send a follow-up patch set and to ask for a Tested-By from people being able to test it. For dm9000 the issue is (again) related to an ordering problem: the Ethernet need an interrupt provided by the gpio driver. Unfortunately, the gpio driver initialization is called after the dm900 driver initialization. Thanks, Gregory > > This serie relies on the following patchs: > usb: at91-udc: fix irq and iomem resource retrieval > ARM: at91: prepare sam9 dt boards transition to common > > Jean-Jacques > > Jean-Jacques Hiblot (8): > at91: dt: Adds support for the bus matrix declaration in the DT > at91: pinctrl: don't request GPIOs used for interrupts but lock them > as IRQ > at91: dt: Add at91sam9261 dt SoC support > at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs > at91: dt: sam9261: Device Tree support for the at91sam9261ek > at91: updated the at91_dt_defconfig with support for the ADS7846 > ARM: at91: prepare common clk transition for sam9261 SoC > ARM: at91: move sam9261 SoC to common clk > > arch/arm/boot/dts/Makefile | 2 + > arch/arm/boot/dts/at91sam9261.dtsi | 740 ++++++++++++++++++++++++++++++++++++ > arch/arm/boot/dts/at91sam9261ek.dts | 204 ++++++++++ > arch/arm/configs/at91_dt_defconfig | 2 + > arch/arm/mach-at91/Kconfig | 1 - > arch/arm/mach-at91/at91sam9261.c | 25 +- > arch/arm/mach-at91/setup.c | 23 ++ > drivers/pinctrl/pinctrl-at91.c | 5 +- > 8 files changed, 996 insertions(+), 6 deletions(-) > create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi > create mode 100644 arch/arm/boot/dts/at91sam9261ek.dts > -- Gregory Clement, Free Electrons Kernel, drivers, real-time and embedded Linux development, consulting, training and support. http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [PATCH v4 0/8] Device Tree support for the at91sam9261ek 2014-02-12 11:14 ` Gregory CLEMENT @ 2014-02-12 12:34 ` Thomas Petazzoni -1 siblings, 0 replies; 54+ messages in thread From: Thomas Petazzoni @ 2014-02-12 12:34 UTC (permalink / raw) To: Gregory CLEMENT Cc: Jean-Jacques Hiblot, nicolas.ferre, plagnioj, b.brezillon, linux-kernel, linux-arm-kernel Dear Gregory CLEMENT, On Wed, 12 Feb 2014 12:14:29 +0100, Gregory CLEMENT wrote: > For dm9000 the issue is (again) related to an ordering problem: > the Ethernet need an interrupt provided by the gpio driver. Unfortunately, > the gpio driver initialization is called after the dm900 driver > initialization. And -EPROBE_DEFER doesn't solve this problem? Thomas -- Thomas Petazzoni, CTO, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 0/8] Device Tree support for the at91sam9261ek @ 2014-02-12 12:34 ` Thomas Petazzoni 0 siblings, 0 replies; 54+ messages in thread From: Thomas Petazzoni @ 2014-02-12 12:34 UTC (permalink / raw) To: linux-arm-kernel Dear Gregory CLEMENT, On Wed, 12 Feb 2014 12:14:29 +0100, Gregory CLEMENT wrote: > For dm9000 the issue is (again) related to an ordering problem: > the Ethernet need an interrupt provided by the gpio driver. Unfortunately, > the gpio driver initialization is called after the dm900 driver > initialization. And -EPROBE_DEFER doesn't solve this problem? Thomas -- Thomas Petazzoni, CTO, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [PATCH v4 0/8] Device Tree support for the at91sam9261ek 2014-02-12 12:34 ` Thomas Petazzoni @ 2014-02-12 12:36 ` Jean-Jacques Hiblot -1 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 12:36 UTC (permalink / raw) To: Thomas Petazzoni Cc: Gregory CLEMENT, Jean-Jacques Hiblot, Nicolas Ferre, Jean-Christophe PLAGNIOL-VILLARD, boris brezillon, Linux Kernel Mailing List, linux-arm-kernel Hi Thomas, 2014-02-12 13:34 GMT+01:00 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>: > Dear Gregory CLEMENT, > > On Wed, 12 Feb 2014 12:14:29 +0100, Gregory CLEMENT wrote: > >> For dm9000 the issue is (again) related to an ordering problem: >> the Ethernet need an interrupt provided by the gpio driver. Unfortunately, >> the gpio driver initialization is called after the dm900 driver >> initialization. > > And -EPROBE_DEFER doesn't solve this problem? not really the problem happens before the driver is actually probed when the ressource for the platform driver are filled > > Thomas > -- > Thomas Petazzoni, CTO, Free Electrons > Embedded Linux, Kernel and Android engineering > http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 0/8] Device Tree support for the at91sam9261ek @ 2014-02-12 12:36 ` Jean-Jacques Hiblot 0 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 12:36 UTC (permalink / raw) To: linux-arm-kernel Hi Thomas, 2014-02-12 13:34 GMT+01:00 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>: > Dear Gregory CLEMENT, > > On Wed, 12 Feb 2014 12:14:29 +0100, Gregory CLEMENT wrote: > >> For dm9000 the issue is (again) related to an ordering problem: >> the Ethernet need an interrupt provided by the gpio driver. Unfortunately, >> the gpio driver initialization is called after the dm900 driver >> initialization. > > And -EPROBE_DEFER doesn't solve this problem? not really the problem happens before the driver is actually probed when the ressource for the platform driver are filled > > Thomas > -- > Thomas Petazzoni, CTO, Free Electrons > Embedded Linux, Kernel and Android engineering > http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [PATCH v4 0/8] Device Tree support for the at91sam9261ek 2014-02-12 12:36 ` Jean-Jacques Hiblot @ 2014-02-12 12:44 ` Thomas Petazzoni -1 siblings, 0 replies; 54+ messages in thread From: Thomas Petazzoni @ 2014-02-12 12:44 UTC (permalink / raw) To: Jean-Jacques Hiblot Cc: Gregory CLEMENT, Nicolas Ferre, Jean-Christophe PLAGNIOL-VILLARD, boris brezillon, Linux Kernel Mailing List, linux-arm-kernel Dear Jean-Jacques Hiblot, On Wed, 12 Feb 2014 13:36:08 +0100, Jean-Jacques Hiblot wrote: > >> For dm9000 the issue is (again) related to an ordering problem: > >> the Ethernet need an interrupt provided by the gpio driver. Unfortunately, > >> the gpio driver initialization is called after the dm900 driver > >> initialization. > > > > And -EPROBE_DEFER doesn't solve this problem? > not really the problem happens before the driver is actually probed > when the ressource for the platform driver are filled Sorry, I don't have all the context. If I understand correctly what you mean, the GPIO driver is probed through the DT, but the DM9000 driver is probed in a legacy way from the board file, and you have the case where the DM9000 platform_device gets registered before the GPIOs are actually available? In this case, what about having the of_platform_populate() call *before* the platform_device_register() for your DM9000 ? Again, I don't have all the context, so I might very well be getting the situation incorrectly. Of course, ideally, the DM9000 driver should be probed using the DT, but I guess this needs the SMC DT binding that is still being discussed, if I followed correctly. Thomas -- Thomas Petazzoni, CTO, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 0/8] Device Tree support for the at91sam9261ek @ 2014-02-12 12:44 ` Thomas Petazzoni 0 siblings, 0 replies; 54+ messages in thread From: Thomas Petazzoni @ 2014-02-12 12:44 UTC (permalink / raw) To: linux-arm-kernel Dear Jean-Jacques Hiblot, On Wed, 12 Feb 2014 13:36:08 +0100, Jean-Jacques Hiblot wrote: > >> For dm9000 the issue is (again) related to an ordering problem: > >> the Ethernet need an interrupt provided by the gpio driver. Unfortunately, > >> the gpio driver initialization is called after the dm900 driver > >> initialization. > > > > And -EPROBE_DEFER doesn't solve this problem? > not really the problem happens before the driver is actually probed > when the ressource for the platform driver are filled Sorry, I don't have all the context. If I understand correctly what you mean, the GPIO driver is probed through the DT, but the DM9000 driver is probed in a legacy way from the board file, and you have the case where the DM9000 platform_device gets registered before the GPIOs are actually available? In this case, what about having the of_platform_populate() call *before* the platform_device_register() for your DM9000 ? Again, I don't have all the context, so I might very well be getting the situation incorrectly. Of course, ideally, the DM9000 driver should be probed using the DT, but I guess this needs the SMC DT binding that is still being discussed, if I followed correctly. Thomas -- Thomas Petazzoni, CTO, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [PATCH v4 0/8] Device Tree support for the at91sam9261ek 2014-02-12 12:44 ` Thomas Petazzoni @ 2014-02-12 13:01 ` Jean-Jacques Hiblot -1 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 13:01 UTC (permalink / raw) To: Thomas Petazzoni Cc: Jean-Jacques Hiblot, Gregory CLEMENT, Nicolas Ferre, Jean-Christophe PLAGNIOL-VILLARD, boris brezillon, Linux Kernel Mailing List, linux-arm-kernel Thomas, I wasn't very informative indeed. The dm9000 is instantiated from the DT, its irq is described as <&pioC 2 IRQ_TYPE_EDGE_BOTH> The problem, as I see it, is that at the time the IRQ description is translated the irq domain doesn't exist yet and the translation fails. The result is that the ressource of the platform driver do not contain any information about an IRQ. The irq domain is added later when the gpio driver is probed (pinctrl-at91.c:1684). A bit later the dm9000 gets probed and fails lamely because it can't find an IRQ ressource. Jean-Jacques 2014-02-12 13:44 GMT+01:00 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>: > Dear Jean-Jacques Hiblot, > > On Wed, 12 Feb 2014 13:36:08 +0100, Jean-Jacques Hiblot wrote: > >> >> For dm9000 the issue is (again) related to an ordering problem: >> >> the Ethernet need an interrupt provided by the gpio driver. Unfortunately, >> >> the gpio driver initialization is called after the dm900 driver >> >> initialization. >> > >> > And -EPROBE_DEFER doesn't solve this problem? >> not really the problem happens before the driver is actually probed >> when the ressource for the platform driver are filled > > Sorry, I don't have all the context. If I understand correctly what you > mean, the GPIO driver is probed through the DT, but the DM9000 driver > is probed in a legacy way from the board file, and you have the case > where the DM9000 platform_device gets registered before the GPIOs are > actually available? In this case, what about having the > of_platform_populate() call *before* the platform_device_register() for > your DM9000 ? Again, I don't have all the context, so I might very well > be getting the situation incorrectly. > > Of course, ideally, the DM9000 driver should be probed using the DT, > but I guess this needs the SMC DT binding that is still being > discussed, if I followed correctly. > > Thomas > -- > Thomas Petazzoni, CTO, Free Electrons > Embedded Linux, Kernel and Android engineering > http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 0/8] Device Tree support for the at91sam9261ek @ 2014-02-12 13:01 ` Jean-Jacques Hiblot 0 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 13:01 UTC (permalink / raw) To: linux-arm-kernel Thomas, I wasn't very informative indeed. The dm9000 is instantiated from the DT, its irq is described as <&pioC 2 IRQ_TYPE_EDGE_BOTH> The problem, as I see it, is that at the time the IRQ description is translated the irq domain doesn't exist yet and the translation fails. The result is that the ressource of the platform driver do not contain any information about an IRQ. The irq domain is added later when the gpio driver is probed (pinctrl-at91.c:1684). A bit later the dm9000 gets probed and fails lamely because it can't find an IRQ ressource. Jean-Jacques 2014-02-12 13:44 GMT+01:00 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>: > Dear Jean-Jacques Hiblot, > > On Wed, 12 Feb 2014 13:36:08 +0100, Jean-Jacques Hiblot wrote: > >> >> For dm9000 the issue is (again) related to an ordering problem: >> >> the Ethernet need an interrupt provided by the gpio driver. Unfortunately, >> >> the gpio driver initialization is called after the dm900 driver >> >> initialization. >> > >> > And -EPROBE_DEFER doesn't solve this problem? >> not really the problem happens before the driver is actually probed >> when the ressource for the platform driver are filled > > Sorry, I don't have all the context. If I understand correctly what you > mean, the GPIO driver is probed through the DT, but the DM9000 driver > is probed in a legacy way from the board file, and you have the case > where the DM9000 platform_device gets registered before the GPIOs are > actually available? In this case, what about having the > of_platform_populate() call *before* the platform_device_register() for > your DM9000 ? Again, I don't have all the context, so I might very well > be getting the situation incorrectly. > > Of course, ideally, the DM9000 driver should be probed using the DT, > but I guess this needs the SMC DT binding that is still being > discussed, if I followed correctly. > > Thomas > -- > Thomas Petazzoni, CTO, Free Electrons > Embedded Linux, Kernel and Android engineering > http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [PATCH v4 0/8] Device Tree support for the at91sam9261ek 2014-02-12 11:14 ` Gregory CLEMENT @ 2014-02-12 12:35 ` Jean-Jacques Hiblot -1 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 12:35 UTC (permalink / raw) To: Gregory CLEMENT Cc: Jean-Jacques Hiblot, Nicolas Ferre, Jean-Christophe PLAGNIOL-VILLARD, boris brezillon, Linux Kernel Mailing List, linux-arm-kernel Hi Greg, 2014-02-12 12:14 GMT+01:00 Gregory CLEMENT <gregory.clement@free-electrons.com>: > Hi Jean-Jacques, > > On 12/02/2014 11:06, Jean-Jacques Hiblot wrote: >> This patch set aims at bringing a device tree support for the sam9261. >> It's mostly based on the sam9263 and sam9x5 stuff. >> >> Changes since V3: >> * Added support for the touchscreen >> * Added support for the spi dataflash >> * Activated the TCB by default >> * Reworked the patch organization to reduce the number of patchs >> * changed the default bootargs (no mem description, UBI on mtdpart 5) >> * Changed the xlate implementation of the at91 pinctrl driver to lock the GPIOs >> for IRQs instead of requesting them (needed for the touchscreen driver) >> * some stylistic changes >> >> Changes since V2: >> * removed the smc driver from the serie. It'll be posted in an independent >> serie later. >> * removed the DM9000 support (it'll come with the smc driver) >> * the sam9261 now supports the Common Clock Framework (CCF). Note: to enable >> the CCF you must remove from the kernel config the platforms that don't >> support it. >> * Added basic DT binding for the bus matrix >> * Added support for USB host >> * Added support for USB gadget >> * in dts(i), replaced interrupt-parent with interrupts-extended >> * changed the nand partition plan (same as for the sama5d3) >> * removed 'mem' parameter in command line >> * re-ordered dt-nodes in ascending address order. >> * split the lcd support patch in 2 parts (SOC and board) >> >> >> Change since V1: >> * changed the DT representation to use address translation and separate the >> timings' configuration from the device properties by adding a "simple-bus" >> inetrmediate node. >> * moved the smc driver from drivers/bus to drivers/memmory >> * smc driver now accepts timings in nanoseconds as well as raw register values >> * smc driver can clip the timings if they're out of bound and dump them to the >> console >> * DM9000 timings are now described in nanosecs (for the virtue of example) >> >> supported features are: >> * working with the Common Clock Framework and the old at91 clock implementation >> * dbgu >> * lcdc >> * usb host >> * usb gadget, >> * spi dataflash >> * nand flash >> * touchscreen >> * leds >> * user buttons >> >> In the TODO list: >> * dm9000 (ethernet) >> * audio >> * mmc > > > Besides the my comment on the 1st patch, all this series > seems pretty neat for me. thanks > > It's worth mentioning also that audio and mmc are in the > TODO list by lack of hardware to test it. So what I suggest actually the audio hardware is present but seems broken on my board. Hopefully I should get another one to test this week. > here is to send a follow-up patch set and to ask for a > Tested-By from people being able to test it. > > For dm9000 the issue is (again) related to an ordering problem: > the Ethernet need an interrupt provided by the gpio driver. Unfortunately, > the gpio driver initialization is called after the dm900 driver > initialization. > > Thanks, > > Gregory > > > >> >> This serie relies on the following patchs: >> usb: at91-udc: fix irq and iomem resource retrieval >> ARM: at91: prepare sam9 dt boards transition to common >> >> Jean-Jacques >> >> Jean-Jacques Hiblot (8): >> at91: dt: Adds support for the bus matrix declaration in the DT >> at91: pinctrl: don't request GPIOs used for interrupts but lock them >> as IRQ >> at91: dt: Add at91sam9261 dt SoC support >> at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs >> at91: dt: sam9261: Device Tree support for the at91sam9261ek >> at91: updated the at91_dt_defconfig with support for the ADS7846 >> ARM: at91: prepare common clk transition for sam9261 SoC >> ARM: at91: move sam9261 SoC to common clk >> >> arch/arm/boot/dts/Makefile | 2 + >> arch/arm/boot/dts/at91sam9261.dtsi | 740 ++++++++++++++++++++++++++++++++++++ >> arch/arm/boot/dts/at91sam9261ek.dts | 204 ++++++++++ >> arch/arm/configs/at91_dt_defconfig | 2 + >> arch/arm/mach-at91/Kconfig | 1 - >> arch/arm/mach-at91/at91sam9261.c | 25 +- >> arch/arm/mach-at91/setup.c | 23 ++ >> drivers/pinctrl/pinctrl-at91.c | 5 +- >> 8 files changed, 996 insertions(+), 6 deletions(-) >> create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi >> create mode 100644 arch/arm/boot/dts/at91sam9261ek.dts >> > > > -- > Gregory Clement, Free Electrons > Kernel, drivers, real-time and embedded Linux > development, consulting, training and support. > http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
* [PATCH v4 0/8] Device Tree support for the at91sam9261ek @ 2014-02-12 12:35 ` Jean-Jacques Hiblot 0 siblings, 0 replies; 54+ messages in thread From: Jean-Jacques Hiblot @ 2014-02-12 12:35 UTC (permalink / raw) To: linux-arm-kernel Hi Greg, 2014-02-12 12:14 GMT+01:00 Gregory CLEMENT <gregory.clement@free-electrons.com>: > Hi Jean-Jacques, > > On 12/02/2014 11:06, Jean-Jacques Hiblot wrote: >> This patch set aims at bringing a device tree support for the sam9261. >> It's mostly based on the sam9263 and sam9x5 stuff. >> >> Changes since V3: >> * Added support for the touchscreen >> * Added support for the spi dataflash >> * Activated the TCB by default >> * Reworked the patch organization to reduce the number of patchs >> * changed the default bootargs (no mem description, UBI on mtdpart 5) >> * Changed the xlate implementation of the at91 pinctrl driver to lock the GPIOs >> for IRQs instead of requesting them (needed for the touchscreen driver) >> * some stylistic changes >> >> Changes since V2: >> * removed the smc driver from the serie. It'll be posted in an independent >> serie later. >> * removed the DM9000 support (it'll come with the smc driver) >> * the sam9261 now supports the Common Clock Framework (CCF). Note: to enable >> the CCF you must remove from the kernel config the platforms that don't >> support it. >> * Added basic DT binding for the bus matrix >> * Added support for USB host >> * Added support for USB gadget >> * in dts(i), replaced interrupt-parent with interrupts-extended >> * changed the nand partition plan (same as for the sama5d3) >> * removed 'mem' parameter in command line >> * re-ordered dt-nodes in ascending address order. >> * split the lcd support patch in 2 parts (SOC and board) >> >> >> Change since V1: >> * changed the DT representation to use address translation and separate the >> timings' configuration from the device properties by adding a "simple-bus" >> inetrmediate node. >> * moved the smc driver from drivers/bus to drivers/memmory >> * smc driver now accepts timings in nanoseconds as well as raw register values >> * smc driver can clip the timings if they're out of bound and dump them to the >> console >> * DM9000 timings are now described in nanosecs (for the virtue of example) >> >> supported features are: >> * working with the Common Clock Framework and the old at91 clock implementation >> * dbgu >> * lcdc >> * usb host >> * usb gadget, >> * spi dataflash >> * nand flash >> * touchscreen >> * leds >> * user buttons >> >> In the TODO list: >> * dm9000 (ethernet) >> * audio >> * mmc > > > Besides the my comment on the 1st patch, all this series > seems pretty neat for me. thanks > > It's worth mentioning also that audio and mmc are in the > TODO list by lack of hardware to test it. So what I suggest actually the audio hardware is present but seems broken on my board. Hopefully I should get another one to test this week. > here is to send a follow-up patch set and to ask for a > Tested-By from people being able to test it. > > For dm9000 the issue is (again) related to an ordering problem: > the Ethernet need an interrupt provided by the gpio driver. Unfortunately, > the gpio driver initialization is called after the dm900 driver > initialization. > > Thanks, > > Gregory > > > >> >> This serie relies on the following patchs: >> usb: at91-udc: fix irq and iomem resource retrieval >> ARM: at91: prepare sam9 dt boards transition to common >> >> Jean-Jacques >> >> Jean-Jacques Hiblot (8): >> at91: dt: Adds support for the bus matrix declaration in the DT >> at91: pinctrl: don't request GPIOs used for interrupts but lock them >> as IRQ >> at91: dt: Add at91sam9261 dt SoC support >> at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs >> at91: dt: sam9261: Device Tree support for the at91sam9261ek >> at91: updated the at91_dt_defconfig with support for the ADS7846 >> ARM: at91: prepare common clk transition for sam9261 SoC >> ARM: at91: move sam9261 SoC to common clk >> >> arch/arm/boot/dts/Makefile | 2 + >> arch/arm/boot/dts/at91sam9261.dtsi | 740 ++++++++++++++++++++++++++++++++++++ >> arch/arm/boot/dts/at91sam9261ek.dts | 204 ++++++++++ >> arch/arm/configs/at91_dt_defconfig | 2 + >> arch/arm/mach-at91/Kconfig | 1 - >> arch/arm/mach-at91/at91sam9261.c | 25 +- >> arch/arm/mach-at91/setup.c | 23 ++ >> drivers/pinctrl/pinctrl-at91.c | 5 +- >> 8 files changed, 996 insertions(+), 6 deletions(-) >> create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi >> create mode 100644 arch/arm/boot/dts/at91sam9261ek.dts >> > > > -- > Gregory Clement, Free Electrons > Kernel, drivers, real-time and embedded Linux > development, consulting, training and support. > http://free-electrons.com ^ permalink raw reply [flat|nested] 54+ messages in thread
end of thread, other threads:[~2014-02-25 10:06 UTC | newest] Thread overview: 54+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2014-02-12 10:06 [PATCH v4 0/8] Device Tree support for the at91sam9261ek Jean-Jacques Hiblot 2014-02-12 10:06 ` Jean-Jacques Hiblot 2014-02-12 10:06 ` [PATCH v4 1/8] at91: dt: Adds support for the bus matrix declaration in the DT Jean-Jacques Hiblot 2014-02-12 10:06 ` Jean-Jacques Hiblot 2014-02-12 10:45 ` Gregory CLEMENT 2014-02-12 10:45 ` Gregory CLEMENT 2014-02-12 10:54 ` Nicolas Ferre 2014-02-12 10:54 ` Nicolas Ferre 2014-02-12 10:06 ` [PATCH v4 2/8] at91: pinctrl: don't request GPIOs used for interrupts but lock them as IRQ Jean-Jacques Hiblot 2014-02-12 10:06 ` Jean-Jacques Hiblot 2014-02-12 17:47 ` Nicolas Ferre 2014-02-12 17:47 ` Nicolas Ferre 2014-02-24 13:25 ` Linus Walleij 2014-02-24 13:25 ` Linus Walleij 2014-02-25 9:35 ` Jean-Jacques Hiblot 2014-02-25 9:35 ` Jean-Jacques Hiblot 2014-02-25 9:47 ` Jean-Jacques Hiblot 2014-02-25 9:47 ` Jean-Jacques Hiblot 2014-02-12 10:06 ` [PATCH v4 3/8] at91: dt: Add at91sam9261 dt SoC support Jean-Jacques Hiblot 2014-02-12 10:06 ` Jean-Jacques Hiblot 2014-02-12 17:28 ` Alexandre Belloni 2014-02-12 17:28 ` Alexandre Belloni 2014-02-12 19:47 ` Jean-Jacques Hiblot 2014-02-12 19:47 ` Jean-Jacques Hiblot 2014-02-13 8:10 ` Nicolas Ferre 2014-02-13 8:10 ` Nicolas Ferre 2014-02-13 8:54 ` Alexandre Belloni 2014-02-13 8:54 ` Alexandre Belloni 2014-02-12 21:04 ` Alexandre Belloni 2014-02-12 21:04 ` Alexandre Belloni 2014-02-13 6:11 ` Jean-Jacques Hiblot 2014-02-13 6:11 ` Jean-Jacques Hiblot 2014-02-12 10:06 ` [PATCH v4 4/8] at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs Jean-Jacques Hiblot 2014-02-12 10:06 ` Jean-Jacques Hiblot 2014-02-12 10:06 ` [PATCH v4 5/8] at91: dt: sam9261: Device Tree support for the at91sam9261ek Jean-Jacques Hiblot 2014-02-12 10:06 ` Jean-Jacques Hiblot 2014-02-12 10:06 ` [PATCH v4 6/8] at91: updated the at91_dt_defconfig with support for the ADS7846 Jean-Jacques Hiblot 2014-02-12 10:06 ` Jean-Jacques Hiblot 2014-02-12 10:06 ` [PATCH v4 7/8] ARM: at91: prepare common clk transition for sam9261 SoC Jean-Jacques Hiblot 2014-02-12 10:06 ` Jean-Jacques Hiblot 2014-02-12 10:06 ` [PATCH v4 8/8] ARM: at91: move sam9261 SoC to common clk Jean-Jacques Hiblot 2014-02-12 10:06 ` Jean-Jacques Hiblot 2014-02-12 11:14 ` [PATCH v4 0/8] Device Tree support for the at91sam9261ek Gregory CLEMENT 2014-02-12 11:14 ` Gregory CLEMENT 2014-02-12 12:34 ` Thomas Petazzoni 2014-02-12 12:34 ` Thomas Petazzoni 2014-02-12 12:36 ` Jean-Jacques Hiblot 2014-02-12 12:36 ` Jean-Jacques Hiblot 2014-02-12 12:44 ` Thomas Petazzoni 2014-02-12 12:44 ` Thomas Petazzoni 2014-02-12 13:01 ` Jean-Jacques Hiblot 2014-02-12 13:01 ` Jean-Jacques Hiblot 2014-02-12 12:35 ` Jean-Jacques Hiblot 2014-02-12 12:35 ` Jean-Jacques Hiblot
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.