[PATCH] V4L: s5k6a3: Add DT binding documentation

[PATCH] V4L: s5k6a3: Add DT binding documentation

[Sylwester Nawrocki]

This patch adds DT binding documentation for the Samsung S5K6A3(YX)
raw image sensor.

Signed-off-by: Sylwester Nawrocki <s.nawrocki-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
Signed-off-by: Kyungmin Park <kyungmin.park-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
---
This patch adds missing documentation [1] for the "samsung,s5k6a3"
compatible. Rob, can you please merge it through your tree if it 
looks OK ?

Thanks,
Sylwester

[1] http://www.spinics.net/lists/devicetree/msg10693.html

Changes since v3 (https://linuxtv.org/patch/20429):
 - rephrased 'clocks' and 'clock-names' properties' description.
---
 .../devicetree/bindings/media/samsung-s5k6a3.txt   |   33 ++++++++++++++++++++
 1 files changed, 33 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/media/samsung-s5k6a3.txt

diff --git a/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt
new file mode 100644
index 0000000..cce01e8
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt
@@ -0,0 +1,33 @@
+Samsung S5K6A3(YX) raw image sensor
+---------------------------------
+
+S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces
+and CCI (I2C compatible) control bus.
+
+Required properties:
+
+- compatible	: "samsung,s5k6a3";
+- reg		: I2C slave address of the sensor;
+- svdda-supply	: core voltage supply;
+- svddio-supply	: I/O voltage supply;
+- afvdd-supply	: AF (actuator) voltage supply;
+- gpios		: specifier of a GPIO connected to the RESET pin;
+- clocks	: should contain list of phandle and clock specifier pairs
+		  according to common clock bindings for the clocks described
+		  in the clock-names property;
+- clock-names	: should contain "extclk" entry for the sensor's EXTCLK clock;
+
+Optional properties:
+
+- clock-frequency : the frequency at which the "extclk" clock should be
+		    configured to operate, in Hz; if this property is not
+		    specified default 24 MHz value will be used.
+
+The common video interfaces bindings (see video-interfaces.txt) should be
+used to specify link to the image data receiver. The S5K6A3(YX) device
+node should contain one 'port' child node with an 'endpoint' subnode.
+
+Following properties are valid for the endpoint node:
+
+- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
+  video-interfaces.txt.  The sensor supports only one data lane.
-- 
1.7.4.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH] V4L: s5k6a3: Add DT binding documentation

[Sylwester Nawrocki]

This patch adds DT binding documentation for the Samsung S5K6A3(YX)
raw image sensor.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
---
This patch adds missing documentation [1] for the "samsung,s5k6a3"
compatible. Rob, can you please merge it through your tree if it 
looks OK ?

Thanks,
Sylwester

[1] http://www.spinics.net/lists/devicetree/msg10693.html

Changes since v3 (https://linuxtv.org/patch/20429):
 - rephrased 'clocks' and 'clock-names' properties' description.
---
 .../devicetree/bindings/media/samsung-s5k6a3.txt   |   33 ++++++++++++++++++++
 1 files changed, 33 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/media/samsung-s5k6a3.txt

diff --git a/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt
new file mode 100644
index 0000000..cce01e8
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt
@@ -0,0 +1,33 @@
+Samsung S5K6A3(YX) raw image sensor
+---------------------------------
+
+S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces
+and CCI (I2C compatible) control bus.
+
+Required properties:
+
+- compatible	: "samsung,s5k6a3";
+- reg		: I2C slave address of the sensor;
+- svdda-supply	: core voltage supply;
+- svddio-supply	: I/O voltage supply;
+- afvdd-supply	: AF (actuator) voltage supply;
+- gpios		: specifier of a GPIO connected to the RESET pin;
+- clocks	: should contain list of phandle and clock specifier pairs
+		  according to common clock bindings for the clocks described
+		  in the clock-names property;
+- clock-names	: should contain "extclk" entry for the sensor's EXTCLK clock;
+
+Optional properties:
+
+- clock-frequency : the frequency at which the "extclk" clock should be
+		    configured to operate, in Hz; if this property is not
+		    specified default 24 MHz value will be used.
+
+The common video interfaces bindings (see video-interfaces.txt) should be
+used to specify link to the image data receiver. The S5K6A3(YX) device
+node should contain one 'port' child node with an 'endpoint' subnode.
+
+Following properties are valid for the endpoint node:
+
+- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
+  video-interfaces.txt.  The sensor supports only one data lane.
-- 
1.7.4.1

Re: [PATCH] V4L: s5k6a3: Add DT binding documentation

[Sylwester Nawrocki]

On 22/12/13 22:27, Sylwester Nawrocki wrote:
> This patch adds DT binding documentation for the Samsung S5K6A3(YX)
> raw image sensor.
> 
> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
> This patch adds missing documentation [1] for the "samsung,s5k6a3"
> compatible. Rob, can you please merge it through your tree if it 
> looks OK ?

Anyone cares to Ack this patch so it can be merged through the media
tree ?

> Thanks,
> Sylwester
> 
> [1] http://www.spinics.net/lists/devicetree/msg10693.html
> 
> Changes since v3 (https://linuxtv.org/patch/20429):
>  - rephrased 'clocks' and 'clock-names' properties' description.
> ---
>  .../devicetree/bindings/media/samsung-s5k6a3.txt   |   33 ++++++++++++++++++++
>  1 files changed, 33 insertions(+), 0 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/media/samsung-s5k6a3.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt
> new file mode 100644
> index 0000000..cce01e8
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt
> @@ -0,0 +1,33 @@
> +Samsung S5K6A3(YX) raw image sensor
> +---------------------------------
> +
> +S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces
> +and CCI (I2C compatible) control bus.
> +
> +Required properties:
> +
> +- compatible	: "samsung,s5k6a3";
> +- reg		: I2C slave address of the sensor;
> +- svdda-supply	: core voltage supply;
> +- svddio-supply	: I/O voltage supply;
> +- afvdd-supply	: AF (actuator) voltage supply;
> +- gpios		: specifier of a GPIO connected to the RESET pin;
> +- clocks	: should contain list of phandle and clock specifier pairs
> +		  according to common clock bindings for the clocks described
> +		  in the clock-names property;
> +- clock-names	: should contain "extclk" entry for the sensor's EXTCLK clock;
> +
> +Optional properties:
> +
> +- clock-frequency : the frequency at which the "extclk" clock should be
> +		    configured to operate, in Hz; if this property is not
> +		    specified default 24 MHz value will be used.
> +
> +The common video interfaces bindings (see video-interfaces.txt) should be
> +used to specify link to the image data receiver. The S5K6A3(YX) device
> +node should contain one 'port' child node with an 'endpoint' subnode.
> +
> +Following properties are valid for the endpoint node:
> +
> +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
> +  video-interfaces.txt.  The sensor supports only one data lane.

Re: [PATCH] V4L: s5k6a3: Add DT binding documentation

[Mark Rutland]

On Tue, Feb 18, 2014 at 03:43:11PM +0000, Sylwester Nawrocki wrote:
> On 22/12/13 22:27, Sylwester Nawrocki wrote:
> > This patch adds DT binding documentation for the Samsung S5K6A3(YX)
> > raw image sensor.
> > 
> > Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
> > Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> > ---
> > This patch adds missing documentation [1] for the "samsung,s5k6a3"
> > compatible. Rob, can you please merge it through your tree if it 
> > looks OK ?
> 
> Anyone cares to Ack this patch so it can be merged through the media
> tree ?

It looks fine to me:

Acked-by: Mark Rutland <mark.rutland@arm.com>

Thanks,
Mark.

> 
> > Thanks,
> > Sylwester
> > 
> > [1] http://www.spinics.net/lists/devicetree/msg10693.html
> > 
> > Changes since v3 (https://linuxtv.org/patch/20429):
> >  - rephrased 'clocks' and 'clock-names' properties' description.
> > ---
> >  .../devicetree/bindings/media/samsung-s5k6a3.txt   |   33 ++++++++++++++++++++
> >  1 files changed, 33 insertions(+), 0 deletions(-)
> >  create mode 100644 Documentation/devicetree/bindings/media/samsung-s5k6a3.txt
> > 
> > diff --git a/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt
> > new file mode 100644
> > index 0000000..cce01e8
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt
> > @@ -0,0 +1,33 @@
> > +Samsung S5K6A3(YX) raw image sensor
> > +---------------------------------
> > +
> > +S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces
> > +and CCI (I2C compatible) control bus.
> > +
> > +Required properties:
> > +
> > +- compatible	: "samsung,s5k6a3";
> > +- reg		: I2C slave address of the sensor;
> > +- svdda-supply	: core voltage supply;
> > +- svddio-supply	: I/O voltage supply;
> > +- afvdd-supply	: AF (actuator) voltage supply;
> > +- gpios		: specifier of a GPIO connected to the RESET pin;
> > +- clocks	: should contain list of phandle and clock specifier pairs
> > +		  according to common clock bindings for the clocks described
> > +		  in the clock-names property;
> > +- clock-names	: should contain "extclk" entry for the sensor's EXTCLK clock;
> > +
> > +Optional properties:
> > +
> > +- clock-frequency : the frequency at which the "extclk" clock should be
> > +		    configured to operate, in Hz; if this property is not
> > +		    specified default 24 MHz value will be used.
> > +
> > +The common video interfaces bindings (see video-interfaces.txt) should be
> > +used to specify link to the image data receiver. The S5K6A3(YX) device
> > +node should contain one 'port' child node with an 'endpoint' subnode.
> > +
> > +Following properties are valid for the endpoint node:
> > +
> > +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
> > +  video-interfaces.txt.  The sensor supports only one data lane.
> 
> 

Re: [PATCH] V4L: s5k6a3: Add DT binding documentation

[Sylwester Nawrocki]

On 19/02/14 18:47, Mark Rutland wrote:
> On Tue, Feb 18, 2014 at 03:43:11PM +0000, Sylwester Nawrocki wrote:
>> > On 22/12/13 22:27, Sylwester Nawrocki wrote:
>>> > > This patch adds DT binding documentation for the Samsung S5K6A3(YX)
>>> > > raw image sensor.
>>> > > 
>>> > > Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
>>> > > Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
>>> > > ---
>>> > > This patch adds missing documentation [1] for the "samsung,s5k6a3"
>>> > > compatible. Rob, can you please merge it through your tree if it 
>>> > > looks OK ?
>> > 
>> > Anyone cares to Ack this patch so it can be merged through the media
>> > tree ?
>
> It looks fine to me:
> 
> Acked-by: Mark Rutland <mark.rutland@arm.com>

Thanks for the review. I'm going to post a short series including this
patch, I would appreciate your (or other DT binding maintainer) review
of the DT binding part, so this stuff can finally be pushed upstream.

Cheers,
Sylwester