* [PATCH 3.14.0-rc4 v2 1/10] rsi: Adding RS9113 driver files
@ 2014-02-25 16:18 Fariya Fatima
0 siblings, 0 replies; only message in thread
From: Fariya Fatima @ 2014-02-25 16:18 UTC (permalink / raw)
To: linux-wireless
From: Fariya Fatima
This driver supports the RS9113 chipset from Redpine Signals Inc. This
driver
supports b/g/n standards. Both SDIO and USB interfaces are supported.
This patch contains the include files.
Signed-off-by: Fariya Fatima <fariya.f@redpinesignals.com>
---
Kconfig | 1
Makefile | 1
rsi/Kconfig | 31 ++++++
rsi/Makefile | 12 ++
rsi/rsi_boot_params.h | 126 +++++++++++++++++++++++++
rsi/rsi_common.h | 244 ++++++++++++++++++++++++++++++++++++++++++++++++++
rsi/rsi_debugfs.h | 52 ++++++++++
rsi/rsi_sdio.h | 129 ++++++++++++++++++++++++++
rsi/rsi_usb.h | 57 +++++++++++
9 files changed, 653 insertions(+)
diff -rupN linux-3.14-rc4/drivers/net/wireless/Kconfig linux-3.14-rc4_new/drivers/net/wireless/Kconfig
--- linux-3.14-rc4/drivers/net/wireless/Kconfig 2014-02-24 07:10:03.000000000 +0530
+++ linux-3.14-rc4_new/drivers/net/wireless/Kconfig 2014-02-25 14:39:38.305337287 +0530
@@ -281,5 +281,6 @@ source "drivers/net/wireless/ti/Kconfig"
source "drivers/net/wireless/zd1211rw/Kconfig"
source "drivers/net/wireless/mwifiex/Kconfig"
source "drivers/net/wireless/cw1200/Kconfig"
+source "drivers/net/wireless/rsi/Kconfig"
endif # WLAN
diff -rupN linux-3.14-rc4/drivers/net/wireless/Makefile linux-3.14-rc4_new/drivers/net/wireless/Makefile
--- linux-3.14-rc4/drivers/net/wireless/Makefile 2014-02-24 07:10:03.000000000 +0530
+++ linux-3.14-rc4_new/drivers/net/wireless/Makefile 2014-02-25 14:39:18.607583543 +0530
@@ -59,3 +59,4 @@ obj-$(CONFIG_BRCMFMAC) += brcm80211/
obj-$(CONFIG_BRCMSMAC) += brcm80211/
obj-$(CONFIG_CW1200) += cw1200/
+obj-$(CONFIG_RSI_91x) += rsi/
diff -rupN linux-3.14-rc4/drivers/net/wireless/rsi/Kconfig linux-3.14-rc4_new/drivers/net/wireless/rsi/Kconfig
--- linux-3.14-rc4/drivers/net/wireless/rsi/Kconfig 1970-01-01 05:30:00.000000000 +0530
+++ linux-3.14-rc4_new/drivers/net/wireless/rsi/Kconfig 2014-02-25 14:40:54.981378704 +0530
@@ -0,0 +1,31 @@
+config RSI_91x
+ tristate "Redpine Signals Inc 91x WLAN driver support"
+ depends on MAC80211
+ default m
+ ---help---
+ This option enabes support for RSI 1x1 devices.
+ Select M (recommended), if you have a RSI 1x1 wireless module.
+
+config RSI_DEBUGFS
+ bool "Redpine Signals Inc debug support"
+ depends on RSI_91x
+ default y
+ ---help---
+ Say Y, if you would like to enable debug support. This option
+ creates debugfs entries
+
+config RSI_SDIO
+ tristate "Redpine Signals SDIO bus support"
+ depends on MMC && RSI_91x
+ default m
+ ---help---
+ This option enables the SDIO bus support in rsi drivers.
+ Select M (recommended), if you have a RSI 1x1 wireless module.
+
+config RSI_USB
+ tristate "Redpine Signals USB bus support"
+ depends on USB && RSI_91x
+ default m
+ ---help---
+ This option enables the USB bus support in rsi drivers.
+ Select M (recommended), if you have a RSI 1x1 wireless module.
diff -rupN linux-3.14-rc4/drivers/net/wireless/rsi/Makefile linux-3.14-rc4_new/drivers/net/wireless/rsi/Makefile
--- linux-3.14-rc4/drivers/net/wireless/rsi/Makefile 1970-01-01 05:30:00.000000000 +0530
+++ linux-3.14-rc4_new/drivers/net/wireless/rsi/Makefile 2014-02-25 14:41:00.410310833 +0530
@@ -0,0 +1,12 @@
+rsi_91x-y += rsi_91x_main.o
+rsi_91x-y += rsi_91x_core.o
+rsi_91x-y += rsi_91x_mac80211.o
+rsi_91x-y += rsi_91x_mgmt.o
+rsi_91x-y += rsi_91x_pkt.o
+rsi_91x-$(CONFIG_RSI_DEBUGFS) += rsi_91x_debugfs.o
+
+rsi_usb-y += rsi_91x_usb.o rsi_91x_usb_ops.o
+rsi_sdio-y += rsi_91x_sdio.o rsi_91x_sdio_ops.o
+obj-$(CONFIG_RSI_91x) += rsi_91x.o
+obj-$(CONFIG_RSI_SDIO) += rsi_sdio.o
+obj-$(CONFIG_RSI_USB) += rsi_usb.o
diff -rupN linux-3.14-rc4/drivers/net/wireless/rsi/rsi_boot_params.h linux-3.14-rc4_new/drivers/net/wireless/rsi/rsi_boot_params.h
--- linux-3.14-rc4/drivers/net/wireless/rsi/rsi_boot_params.h 1970-01-01 05:30:00.000000000 +0530
+++ linux-3.14-rc4_new/drivers/net/wireless/rsi/rsi_boot_params.h 2014-02-25 14:41:09.410198319 +0530
@@ -0,0 +1,126 @@
+/**
+ * Copyright (c) 2014 Redpine Signals Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef __RSI_BOOTPARAMS_HEADER_H__
+#define __RSI_BOOTPARAMS_HEADER_H__
+
+#define CRYSTAL_GOOD_TIME BIT(0)
+#define BOOTUP_MODE_INFO BIT(1)
+#define WIFI_TAPLL_CONFIGS BIT(5)
+#define WIFI_PLL960_CONFIGS BIT(6)
+#define WIFI_AFEPLL_CONFIGS BIT(7)
+#define WIFI_SWITCH_CLK_CONFIGS BIT(8)
+
+#define TA_PLL_M_VAL_20 8
+#define TA_PLL_N_VAL_20 1
+#define TA_PLL_P_VAL_20 4
+
+#define PLL960_M_VAL_20 0x14
+#define PLL960_N_VAL_20 0
+#define PLL960_P_VAL_20 5
+
+#define UMAC_CLK_40MHZ 40
+
+#define TA_PLL_M_VAL_40 46
+#define TA_PLL_N_VAL_40 3
+#define TA_PLL_P_VAL_40 3
+
+#define PLL960_M_VAL_40 0x14
+#define PLL960_N_VAL_40 0
+#define PLL960_P_VAL_40 5
+
+#define UMAC_CLK_20BW \
+ (((TA_PLL_M_VAL_20 + 1) * 40) / \
+ ((TA_PLL_N_VAL_20 + 1) * (TA_PLL_P_VAL_20 + 1)))
+#define VALID_20 \
+ (WIFI_PLL960_CONFIGS | WIFI_AFEPLL_CONFIGS | WIFI_SWITCH_CLK_CONFIGS)
+#define UMAC_CLK_40BW \
+ (((TA_PLL_M_VAL_40 + 1) * 40) / \
+ ((TA_PLL_N_VAL_40 + 1) * (TA_PLL_P_VAL_40 + 1)))
+#define VALID_40 \
+ (WIFI_PLL960_CONFIGS | WIFI_AFEPLL_CONFIGS | WIFI_SWITCH_CLK_CONFIGS | \
+ WIFI_TAPLL_CONFIGS | CRYSTAL_GOOD_TIME | BOOTUP_MODE_INFO)
+
+/* structure to store configs related to TAPLL programming */
+struct tapll_info {
+ __le16 pll_reg_1;
+ __le16 pll_reg_2;
+} __packed;
+
+/* structure to store configs related to PLL960 programming */
+struct pll960_info {
+ __le16 pll_reg_1;
+ __le16 pll_reg_2;
+ __le16 pll_reg_3;
+} __packed;
+
+/* structure to store configs related to AFEPLL programming */
+struct afepll_info {
+ __le16 pll_reg;
+} __packed;
+
+/* structure to store configs related to pll configs */
+struct pll_config {
+ struct tapll_info tapll_info_g;
+ struct pll960_info pll960_info_g;
+ struct afepll_info afepll_info_g;
+} __packed;
+
+/* structure to store configs related to UMAC clk programming */
+struct switch_clk {
+ __le16 switch_clk_info;
+ /* If switch_bbp_lmac_clk_reg is set then this value will be programmed
+ * into reg
+ */
+ __le16 bbp_lmac_clk_reg_val;
+ /* if switch_umac_clk is set then this value will be programmed */
+ __le16 umac_clock_reg_config;
+ /* if switch_qspi_clk is set then this value will be programmed */
+ __le16 qspi_uart_clock_reg_config;
+} __packed;
+
+struct device_clk_info {
+ struct pll_config pll_config_g;
+ struct switch_clk switch_clk_g;
+} __packed;
+
+struct bootup_params {
+ __le16 magic_number;
+ __le16 crystal_good_time;
+ __le32 valid;
+ __le32 reserved_for_valids;
+ __le16 bootup_mode_info;
+ /* configuration used for digital loop back */
+ __le16 digital_loop_back_params;
+ __le16 rtls_timestamp_en;
+ __le16 host_spi_intr_cfg;
+ struct device_clk_info device_clk_info[3];
+ /* ulp buckboost wait time */
+ __le32 buckboost_wakeup_cnt;
+ /* pmu wakeup wait time & WDT EN info */
+ __le16 pmu_wakeup_wait;
+ u8 shutdown_wait_time;
+ /* Sleep clock source selection */
+ u8 pmu_slp_clkout_sel;
+ /* WDT programming values */
+ __le32 wdt_prog_value;
+ /* WDT soc reset delay */
+ __le32 wdt_soc_rst_delay;
+ /* dcdc modes configs */
+ __le32 dcdc_operation_mode;
+ __le32 soc_reset_wait_cnt;
+} __packed;
+#endif
diff -rupN linux-3.14-rc4/drivers/net/wireless/rsi/rsi_common.h linux-3.14-rc4_new/drivers/net/wireless/rsi/rsi_common.h
--- linux-3.14-rc4/drivers/net/wireless/rsi/rsi_common.h 1970-01-01 05:30:00.000000000 +0530
+++ linux-3.14-rc4_new/drivers/net/wireless/rsi/rsi_common.h 2014-02-25 14:41:09.410198319 +0530
@@ -0,0 +1,244 @@
+/**
+ * Copyright (c) 2014 Redpine Signals Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef __RSI_COMMON_H__
+#define __RSI_COMMON_H__
+
+#include <linux/string.h>
+#include <linux/skbuff.h>
+#include <net/mac80211.h>
+
+#define ERR_ZONE BIT(0) /* For Error Msgs */
+#define INFO_ZONE BIT(1) /* For General Status Msgs */
+#define INIT_ZONE BIT(2) /* For Driver Init Seq Msgs */
+#define MGMT_TX_ZONE BIT(3) /* For TX Mgmt Path Msgs */
+#define MGMT_RX_ZONE BIT(4) /* For RX Mgmt Path Msgs */
+#define DATA_TX_ZONE BIT(5) /* For TX Data Path Msgs */
+#define DATA_RX_ZONE BIT(6) /* For RX Data Path Msgs */
+#define FSM_ZONE BIT(7) /* For State Machine Msgs */
+#define ISR_ZONE BIT(8) /* For Interrupt Msgs */
+
+#define FSM_CARD_NOT_READY 0
+#define FSM_BOOT_PARAMS_SENT 1
+#define FSM_EEPROM_READ_MAC_ADDR 2
+#define FSM_RESET_MAC_SENT 3
+#define FSM_RADIO_CAPS_SENT 4
+#define FSM_BB_RF_PROG_SENT 5
+#define FSM_MAC_INIT_DONE 6
+
+extern u32 rsi_zone_enabled;
+
+static inline void rsi_dbg(u32 zone, const char *fmt, ...)
+{
+ struct va_format vaf;
+ va_list args;
+
+ va_start(args, fmt);
+
+ vaf.fmt = fmt;
+ vaf.va = &args;
+
+ if (zone & rsi_zone_enabled)
+ pr_info("%pV", &vaf);
+ va_end(args);
+}
+
+#define RSI_MAX_VIFS 1
+#define NUM_EDCA_QUEUES 4
+#define IEEE80211_ADDR_LEN 6
+#define FRAME_DESC_SZ 16
+#define MIN_802_11_HDR_LEN 24
+
+#define IEEE80211_QOS_ENABLED 0x80
+
+#define DATA_QUEUE_WATER_MARK 400
+#define MIN_DATA_QUEUE_WATER_MARK 300
+#define MULTICAST_WATER_MARK 200
+#define MAC_80211_HDR_FRAME_CONTROL 0
+#define WME_NUM_AC 4
+#define NUM_SOFT_QUEUES 5
+#define MAX_HW_QUEUES 8
+#define INVALID_QUEUE 0xff
+#define MAX_CONTINUOUS_VO_PKTS 8
+#define MAX_CONTINUOUS_VI_PKTS 4
+
+/* Queue information */
+#define RSI_WIFI_MGMT_Q 0x4
+#define RSI_WIFI_DATA_Q 0x5
+#define IEEE80211_MGMT_FRAME 0x00
+#define IEEE80211_CTL_FRAME 0x04
+
+#define IEEE80211_QOS_TID 0x0f
+#define IEEE80211_NONQOS_TID 16
+
+#define TID_TO_WME_AC(_tid) ( \
+ ((_tid) == 0 || (_tid) == 3) ? BE_Q : \
+ ((_tid) < 3) ? BK_Q : \
+ ((_tid) < 6) ? VI_Q : \
+ VO_Q)
+
+#define WME_AC(_q) ( \
+ ((_q) == BK_Q) ? IEEE80211_AC_BK : \
+ ((_q) == BE_Q) ? IEEE80211_AC_BE : \
+ ((_q) == VI_Q) ? IEEE80211_AC_VI : \
+ IEEE80211_AC_VO)
+
+struct version_info {
+ u16 major;
+ u16 minor;
+ u16 release_num;
+ u16 patch_num;
+} __packed;
+
+struct skb_info {
+ s8 rssi;
+ u32 flags;
+ u16 channel;
+ s8 tid;
+ s8 sta_id;
+};
+
+enum EDCA_QUEUE {
+ BK_Q,
+ BE_Q,
+ VI_Q,
+ VO_Q,
+ MGMT_SOFT_Q
+};
+
+struct security_info {
+ bool security_enable;
+ u32 ptk_cipher;
+ u32 gtk_cipher;
+};
+
+struct wmm_qinfo {
+ s32 weight;
+ s32 wme_params;
+ s32 pkt_contended;
+};
+
+struct transmit_q_stats {
+ u32 total_tx_pkt_send[NUM_EDCA_QUEUES + 1];
+ u32 total_tx_pkt_freed[NUM_EDCA_QUEUES + 1];
+};
+
+struct vif_priv {
+ bool is_ht;
+ bool sgi;
+ u16 seq_start;
+};
+
+struct rsi_thread {
+ void (*thread_function)(void *);
+ struct completion completion;
+ struct task_struct *task;
+};
+
+struct rsi_event {
+ atomic_t event_condition;
+ wait_queue_head_t event_queue;
+};
+
+struct rsi_hw;
+
+struct rsi_common {
+ struct rsi_hw *priv;
+ struct vif_priv vif_info[RSI_MAX_VIFS];
+
+ bool mgmt_q_block;
+ struct version_info driver_ver;
+ struct version_info fw_ver;
+
+ struct rsi_thread tx_thread;
+ /* rx_thread used only in case of USB */
+ struct rsi_thread rx_thread;
+ struct sk_buff_head tx_queue[NUM_EDCA_QUEUES + 1];
+ struct rsi_event tx_event;
+ struct rsi_event rx_event;
+ /* Mutex declaration */
+ struct mutex mutex;
+ /* Mutex used between tx/rx threads */
+ struct mutex tx_rxlock;
+ atomic_t tx_thread_done;
+ atomic_t rx_thread_done;
+ u8 endpoint;
+
+ /* Channel/band related */
+ u8 band;
+ u8 channel_width;
+
+ u16 rts_threshold;
+ u16 bitrate_mask[2];
+ u32 fixedrate_mask[2];
+
+ u8 rf_reset;
+ struct transmit_q_stats tx_stats;
+ struct security_info secinfo;
+ struct wmm_qinfo tx_qinfo[NUM_EDCA_QUEUES];
+ struct ieee80211_tx_queue_params edca_params[NUM_EDCA_QUEUES];
+ u8 mac_addr[IEEE80211_ADDR_LEN];
+
+ /* state related */
+ u32 fsm_state;
+ bool init_done;
+ u8 bb_rf_prog_count;
+ bool iface_down;
+
+ /* Generic */
+ u8 channel;
+ u8 *rx_data_pkt;
+ u8 mac_id;
+ u8 radio_id;
+ u16 rate_pwr[20];
+ u16 min_rate;
+
+ /* WMM algo related */
+ u8 selected_qnum;
+ u32 pkt_cnt;
+ u8 min_weight;
+};
+
+enum rsi_91x_intf {
+ RSI_91X_INTF_USB,
+ RSI_91X_INTF_SDIO
+};
+
+struct rsi_hw_intf_ops {
+ int (*host_intf_read_pkt)(struct rsi_hw *adapter, u8 *pkt, u32 len);
+ int (*host_intf_write_pkt)(struct rsi_hw *adapter, u8 *pkt, u32 len);
+ int (*read_buffer_status)(struct rsi_hw *adapter);
+ int (*rx_urb_submit)(struct rsi_hw *adapter);
+};
+
+struct rsi_hw {
+ struct rsi_common *priv;
+ struct ieee80211_hw *hw;
+ struct ieee80211_vif *vifs[RSI_MAX_VIFS];
+ struct ieee80211_tx_queue_params edca_params[NUM_EDCA_QUEUES];
+ struct ieee80211_supported_band sbands[IEEE80211_NUM_BANDS];
+
+ struct device *device;
+ u8 sc_nvifs;
+
+#ifdef CONFIG_RSI_DEBUGFS
+ struct rsi_debugfs *dfsentry;
+#endif
+ void *rsi_device;
+ enum rsi_91x_intf hw_intf;
+ struct rsi_hw_intf_ops *hw_intf_ops;
+};
+#endif
diff -rupN linux-3.14-rc4/drivers/net/wireless/rsi/rsi_debugfs.h linux-3.14-rc4_new/drivers/net/wireless/rsi/rsi_debugfs.h
--- linux-3.14-rc4/drivers/net/wireless/rsi/rsi_debugfs.h 1970-01-01 05:30:00.000000000 +0530
+++ linux-3.14-rc4_new/drivers/net/wireless/rsi/rsi_debugfs.h 2014-02-25 14:41:09.410198319 +0530
@@ -0,0 +1,52 @@
+/**
+ * Copyright (c) 2014 Redpine Signals Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef __RSI_DEBUGFS_H__
+#define __RSI_DEBUGFS_H__
+
+#include "rsi_common.h"
+#include <linux/debugfs.h>
+
+#define FOPS(fopen) { \
+ .owner = THIS_MODULE, \
+ .open = (fopen), \
+ .read = seq_read, \
+ .llseek = seq_lseek, \
+}
+
+#define FOPS_RW(fopen, fwrite) { \
+ .owner = THIS_MODULE, \
+ .open = (fopen), \
+ .read = seq_read, \
+ .llseek = seq_lseek, \
+ .write = (fwrite), \
+}
+
+struct rsi_dbg_files {
+ const char *name;
+ umode_t perms;
+ const struct file_operations fops;
+};
+
+struct rsi_debugfs {
+ struct dentry *subdir;
+ struct rsi_dbg_ops *dfs_get_ops;
+ struct dentry *rsi_files[4];
+};
+
+int rsi_init_dbgfs(struct rsi_hw *adapter);
+void rsi_remove_dbgfs(struct rsi_hw *adapter);
+#endif
diff -rupN linux-3.14-rc4/drivers/net/wireless/rsi/rsi_sdio.h linux-3.14-rc4_new/drivers/net/wireless/rsi/rsi_sdio.h
--- linux-3.14-rc4/drivers/net/wireless/rsi/rsi_sdio.h 1970-01-01 05:30:00.000000000 +0530
+++ linux-3.14-rc4_new/drivers/net/wireless/rsi/rsi_sdio.h 2014-02-25 14:41:09.410198319 +0530
@@ -0,0 +1,129 @@
+/**
+ * @section LICENSE
+ * Copyright (c) 2014 Redpine Signals Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#ifndef __RSI_SDIO_INTF__
+#define __RSI_SDIO_INTF__
+
+#include <linux/mmc/card.h>
+#include <linux/mmc/mmc.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/sdio_func.h>
+#include <linux/mmc/sdio.h>
+#include <linux/mmc/sd.h>
+#include <linux/mmc/sdio_ids.h>
+#include "rsi_common.h"
+
+enum SDIO_INTERRUPT_TYPE {
+ BUFFER_FULL = 0x0,
+ BUFFER_AVAILABLE = 0x1,
+ FIRMWARE_ASSERT_IND = 0x3,
+ MSDU_PACKET_PENDING = 0x4,
+ UNKNOWN_INT = 0XE
+};
+
+/* Buffer status register related info */
+#define PKT_BUFF_SEMI_FULL 0
+#define PKT_BUFF_FULL 1
+#define PKT_MGMT_BUFF_FULL 2
+#define MSDU_PKT_PENDING 3
+/* Interrupt Bit Related Macros */
+#define PKT_BUFF_AVAILABLE 0
+#define FW_ASSERT_IND 2
+
+#define RSI_DEVICE_BUFFER_STATUS_REGISTER 0xf3
+#define RSI_FN1_INT_REGISTER 0xf9
+#define RSI_SD_REQUEST_MASTER 0x10000
+
+/* FOR SD CARD ONLY */
+#define SDIO_RX_NUM_BLOCKS_REG 0x000F1
+#define SDIO_FW_STATUS_REG 0x000F2
+#define SDIO_NXT_RD_DELAY2 0x000F5
+#define SDIO_MASTER_ACCESS_MSBYTE 0x000FA
+#define SDIO_MASTER_ACCESS_LSBYTE 0x000FB
+#define SDIO_READ_START_LVL 0x000FC
+#define SDIO_READ_FIFO_CTL 0x000FD
+#define SDIO_WRITE_FIFO_CTL 0x000FE
+#define SDIO_FUN1_INTR_CLR_REG 0x0008
+#define SDIO_REG_HIGH_SPEED 0x0013
+
+#define RSI_GET_SDIO_INTERRUPT_TYPE(_I, TYPE) \
+ { \
+ TYPE = \
+ (_I & (1 << PKT_BUFF_AVAILABLE)) ? \
+ BUFFER_AVAILABLE : \
+ (_I & (1 << MSDU_PKT_PENDING)) ? \
+ MSDU_PACKET_PENDING : \
+ (_I & (1 << FW_ASSERT_IND)) ? \
+ FIRMWARE_ASSERT_IND : UNKNOWN_INT; \
+ }
+
+/* common registers in SDIO function1 */
+#define TA_SOFT_RESET_REG 0x0004
+#define TA_TH0_PC_REG 0x0400
+#define TA_HOLD_THREAD_REG 0x0844
+#define TA_RELEASE_THREAD_REG 0x0848
+
+#define TA_SOFT_RST_CLR 0
+#define TA_SOFT_RST_SET BIT(0)
+#define TA_PC_ZERO 0
+#define TA_HOLD_THREAD_VALUE cpu_to_le32(0xF)
+#define TA_RELEASE_THREAD_VALUE cpu_to_le32(0xF)
+#define TA_BASE_ADDR 0x2200
+#define MISC_CFG_BASE_ADDR 0x4150
+
+struct receive_info {
+ bool buffer_full;
+ bool semi_buffer_full;
+ bool mgmt_buffer_full;
+ u32 mgmt_buf_full_counter;
+ u32 buf_semi_full_counter;
+ u8 watch_bufferfull_count;
+ u32 sdio_intr_status_zero;
+ u32 sdio_int_counter;
+ u32 total_sdio_msdu_pending_intr;
+ u32 total_sdio_unknown_intr;
+ u32 buf_full_counter;
+ u32 buf_avilable_counter;
+};
+
+struct rsi_91xdev {
+ struct sdio_func *pfunction;
+ struct task_struct *in_sdio_litefi_irq;
+ struct receive_info rx_info;
+ u32 next_read_delay;
+ u32 sdio_high_speed_enable;
+ u8 sdio_clock_speed;
+ u32 cardcapability;
+ u8 prev_desc[16];
+ u32 tx_blk_size;
+ u8 write_fail;
+};
+
+void rsi_interrupt_handler(struct rsi_hw *adapter);
+int rsi_init_sdio_slave_regs(struct rsi_hw *adapter);
+int rsi_device_init(struct rsi_common *common);
+int rsi_device_deinit(struct rsi_hw *adapter);
+struct rsi_hw_intf_ops *rsi_get_hw_intf_ops(void);
+int rsi_read_register(struct rsi_hw *adapter, u32 addr, u8 *data);
+int rsi_host_intf_read_pkt(struct rsi_hw *adapter, u8 *pkt, u32 length);
+int rsi_host_intf_write_pkt(struct rsi_hw *adapter, u8 *pkt, u32 len);
+int rsi_write_register(struct rsi_hw *adapter, u8 function, u32 addr, u8 *data);
+int rsi_write_register_multiple(struct rsi_hw *adapter, u32 addr,
+ u8 *data, u32 count);
+void rsi_ack_interrupt(struct rsi_hw *adapter, u8 int_bit);
+#endif
diff -rupN linux-3.14-rc4/drivers/net/wireless/rsi/rsi_usb.h linux-3.14-rc4_new/drivers/net/wireless/rsi/rsi_usb.h
--- linux-3.14-rc4/drivers/net/wireless/rsi/rsi_usb.h 1970-01-01 05:30:00.000000000 +0530
+++ linux-3.14-rc4_new/drivers/net/wireless/rsi/rsi_usb.h 2014-02-25 14:41:09.410198319 +0530
@@ -0,0 +1,57 @@
+/**
+ * @section LICENSE
+ * Copyright (c) 2014 Redpine Signals Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef __RSI_USB_INTF__
+#define __RSI_USB_INTF__
+
+#include <linux/usb.h>
+#include "rsi_common.h"
+
+#define USB_INTERNAL_REG_1 0x25000
+#define RSI_USB_READY_MAGIC_NUM 0xab
+#define FW_STATUS_REG 0x41050012
+
+#define USB_VENDOR_REGISTER_READ 0x15
+#define USB_VENDOR_REGISTER_WRITE 0x16
+#define RSI_USB_TX_HEAD_ROOM 128
+
+#define MAX_RX_URBS 1
+#define MAX_BULK_EP 8
+#define MGMT_EP 1
+#define DATA_EP 2
+
+struct rsi_91xdev {
+ u8 endpoint;
+ struct usb_device *usbdev;
+ struct usb_interface *pfunction;
+ struct urb *rx_usb_urb[MAX_RX_URBS];
+ u8 *tx_buffer;
+ u32 bulkin_size;
+ u8 bulkin_endpoint_addr;
+ u32 bulkout_size[MAX_BULK_EP];
+ u8 bulkout_endpoint_addr[MAX_BULK_EP];
+ u32 tx_blk_size;
+ u8 write_fail;
+};
+struct rsi_hw_intf_ops *rsi_get_hw_intf_ops(void);
+int rsi_device_init(struct rsi_common *common);
+int rsi_device_deinit(struct rsi_hw *adapter);
+int rsi_write_ta_register_multiple(struct rsi_hw *adapter, u32 addr,
+ u8 *data, u32 count);
+int rsi_rx_urb_submit(struct rsi_hw *adapter);
+int rsi_host_intf_write_pkt(struct rsi_hw *adapter, u8 *pkt, u32 len);
+#endif
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2014-02-25 16:26 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-02-25 16:18 [PATCH 3.14.0-rc4 v2 1/10] rsi: Adding RS9113 driver files Fariya Fatima
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.