[PATCH v9 0/9] USB Host support for OMAP5 uEVM

[PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Roger Quadros]

Hi,

This patchset brings up USB Host ports and Ethernet port on
the OMAP5 uEVM board.

It also does some cleanup with respect to DT clock binding
for the mfd/omap-usb-host driver.

Please queue these for -next.

Lee,

I've folded some platform data dependent patches with mfd patches
so that they don't break functionality when applied individually.
You can safely pull in all MFD patches (1 to 6).

Tony & Benoit,

Can you please accept patches 7, 8 and 9?

Thanks.

Tested on:
 - OMAP5 uEVM
 - Pandaboard ES Rev. B1
 - Beagleboard-XM Rev C2 (DT + Legacy)
 - Beagleboard Rev C4 (DT + Legacy)

Changelog:

v9:
- Folded dependent platform data patches into MFD patches.

v8:
- Addressed review comments and split patch
  "mfd: omap-usb-host: Get clocks based on hardware revision"
- Removed unnecessary usb host dummy clocks on OMAP3
- Removed unnecessary clock alias "ehci_logic_fck" for OMAP3
- Rebased on 3.14-rc3

v7:
- Rebased on 3.14-rc2
- Removed incompatible ids from DT files and examples

v6:
- Initialized clocks to -ENODEV and split patch 3.

v5:
- Expose all clocks in the DT binding document for mfd:omap-usb-host
and mfd:omap-usb-tll

v4:
- Updated DT binding document for clock binding

v3:
- Rebased on top of 3.13-rc7

cheers,
-roger

---
Roger Quadros (9):
  mfd: omap-usb-host: Get clocks based on hardware revision
  mfd: omap-usb-host: Always fail on clk_get() error
  mfd: omap-usb-host: Use proper clock name instead of alias
  mfd: omap-usb-host: Use clock names as per function for reference
    clocks
  mfd: omap-usb-host: Update DT clock binding information
  mfd: omap-usb-tll: Update DT clock binding information
  ARM: OMAP2+: Remove legacy_init_ehci_clk()
  ARM: dts: OMAP2+: Get rid of incompatible ids for USB host nodes
  usb: omap: dts: Update DT binding example usage

 .../devicetree/bindings/mfd/omap-usb-host.txt      |  23 ++++
 .../devicetree/bindings/mfd/omap-usb-tll.txt       |  10 ++
 .../devicetree/bindings/usb/ehci-omap.txt          |   2 +-
 .../devicetree/bindings/usb/ohci-omap3.txt         |   2 +-
 arch/arm/boot/dts/omap3.dtsi                       |   4 +-
 arch/arm/boot/dts/omap4-panda-common.dtsi          |   8 +-
 arch/arm/boot/dts/omap4.dtsi                       |  10 +-
 arch/arm/boot/dts/omap5-uevm.dts                   |   8 +-
 arch/arm/boot/dts/omap5.dtsi                       |  10 +-
 arch/arm/mach-omap2/cclock3xxx_data.c              |   4 -
 arch/arm/mach-omap2/omap_hwmod_3xxx_data.c         |   6 --
 arch/arm/mach-omap2/pdata-quirks.c                 |  16 ---
 drivers/clk/ti/clk-3xxx.c                          |   4 -
 drivers/mfd/omap-usb-host.c                        | 116 ++++++++++++++-------
 14 files changed, 135 insertions(+), 88 deletions(-)

-- 
1.8.3.2

[PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Roger Quadros]

Hi,

This patchset brings up USB Host ports and Ethernet port on
the OMAP5 uEVM board.

It also does some cleanup with respect to DT clock binding
for the mfd/omap-usb-host driver.

Please queue these for -next.

Lee,

I've folded some platform data dependent patches with mfd patches
so that they don't break functionality when applied individually.
You can safely pull in all MFD patches (1 to 6).

Tony & Benoit,

Can you please accept patches 7, 8 and 9?

Thanks.

Tested on:
 - OMAP5 uEVM
 - Pandaboard ES Rev. B1
 - Beagleboard-XM Rev C2 (DT + Legacy)
 - Beagleboard Rev C4 (DT + Legacy)

Changelog:

v9:
- Folded dependent platform data patches into MFD patches.

v8:
- Addressed review comments and split patch
  "mfd: omap-usb-host: Get clocks based on hardware revision"
- Removed unnecessary usb host dummy clocks on OMAP3
- Removed unnecessary clock alias "ehci_logic_fck" for OMAP3
- Rebased on 3.14-rc3

v7:
- Rebased on 3.14-rc2
- Removed incompatible ids from DT files and examples

v6:
- Initialized clocks to -ENODEV and split patch 3.

v5:
- Expose all clocks in the DT binding document for mfd:omap-usb-host
and mfd:omap-usb-tll

v4:
- Updated DT binding document for clock binding

v3:
- Rebased on top of 3.13-rc7

cheers,
-roger

---
Roger Quadros (9):
  mfd: omap-usb-host: Get clocks based on hardware revision
  mfd: omap-usb-host: Always fail on clk_get() error
  mfd: omap-usb-host: Use proper clock name instead of alias
  mfd: omap-usb-host: Use clock names as per function for reference
    clocks
  mfd: omap-usb-host: Update DT clock binding information
  mfd: omap-usb-tll: Update DT clock binding information
  ARM: OMAP2+: Remove legacy_init_ehci_clk()
  ARM: dts: OMAP2+: Get rid of incompatible ids for USB host nodes
  usb: omap: dts: Update DT binding example usage

 .../devicetree/bindings/mfd/omap-usb-host.txt      |  23 ++++
 .../devicetree/bindings/mfd/omap-usb-tll.txt       |  10 ++
 .../devicetree/bindings/usb/ehci-omap.txt          |   2 +-
 .../devicetree/bindings/usb/ohci-omap3.txt         |   2 +-
 arch/arm/boot/dts/omap3.dtsi                       |   4 +-
 arch/arm/boot/dts/omap4-panda-common.dtsi          |   8 +-
 arch/arm/boot/dts/omap4.dtsi                       |  10 +-
 arch/arm/boot/dts/omap5-uevm.dts                   |   8 +-
 arch/arm/boot/dts/omap5.dtsi                       |  10 +-
 arch/arm/mach-omap2/cclock3xxx_data.c              |   4 -
 arch/arm/mach-omap2/omap_hwmod_3xxx_data.c         |   6 --
 arch/arm/mach-omap2/pdata-quirks.c                 |  16 ---
 drivers/clk/ti/clk-3xxx.c                          |   4 -
 drivers/mfd/omap-usb-host.c                        | 116 ++++++++++++++-------
 14 files changed, 135 insertions(+), 88 deletions(-)

-- 
1.8.3.2

[PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Roger Quadros]

Hi,

This patchset brings up USB Host ports and Ethernet port on
the OMAP5 uEVM board.

It also does some cleanup with respect to DT clock binding
for the mfd/omap-usb-host driver.

Please queue these for -next.

Lee,

I've folded some platform data dependent patches with mfd patches
so that they don't break functionality when applied individually.
You can safely pull in all MFD patches (1 to 6).

Tony & Benoit,

Can you please accept patches 7, 8 and 9?

Thanks.

Tested on:
 - OMAP5 uEVM
 - Pandaboard ES Rev. B1
 - Beagleboard-XM Rev C2 (DT + Legacy)
 - Beagleboard Rev C4 (DT + Legacy)

Changelog:

v9:
- Folded dependent platform data patches into MFD patches.

v8:
- Addressed review comments and split patch
  "mfd: omap-usb-host: Get clocks based on hardware revision"
- Removed unnecessary usb host dummy clocks on OMAP3
- Removed unnecessary clock alias "ehci_logic_fck" for OMAP3
- Rebased on 3.14-rc3

v7:
- Rebased on 3.14-rc2
- Removed incompatible ids from DT files and examples

v6:
- Initialized clocks to -ENODEV and split patch 3.

v5:
- Expose all clocks in the DT binding document for mfd:omap-usb-host
and mfd:omap-usb-tll

v4:
- Updated DT binding document for clock binding

v3:
- Rebased on top of 3.13-rc7

cheers,
-roger

---
Roger Quadros (9):
  mfd: omap-usb-host: Get clocks based on hardware revision
  mfd: omap-usb-host: Always fail on clk_get() error
  mfd: omap-usb-host: Use proper clock name instead of alias
  mfd: omap-usb-host: Use clock names as per function for reference
    clocks
  mfd: omap-usb-host: Update DT clock binding information
  mfd: omap-usb-tll: Update DT clock binding information
  ARM: OMAP2+: Remove legacy_init_ehci_clk()
  ARM: dts: OMAP2+: Get rid of incompatible ids for USB host nodes
  usb: omap: dts: Update DT binding example usage

 .../devicetree/bindings/mfd/omap-usb-host.txt      |  23 ++++
 .../devicetree/bindings/mfd/omap-usb-tll.txt       |  10 ++
 .../devicetree/bindings/usb/ehci-omap.txt          |   2 +-
 .../devicetree/bindings/usb/ohci-omap3.txt         |   2 +-
 arch/arm/boot/dts/omap3.dtsi                       |   4 +-
 arch/arm/boot/dts/omap4-panda-common.dtsi          |   8 +-
 arch/arm/boot/dts/omap4.dtsi                       |  10 +-
 arch/arm/boot/dts/omap5-uevm.dts                   |   8 +-
 arch/arm/boot/dts/omap5.dtsi                       |  10 +-
 arch/arm/mach-omap2/cclock3xxx_data.c              |   4 -
 arch/arm/mach-omap2/omap_hwmod_3xxx_data.c         |   6 --
 arch/arm/mach-omap2/pdata-quirks.c                 |  16 ---
 drivers/clk/ti/clk-3xxx.c                          |   4 -
 drivers/mfd/omap-usb-host.c                        | 116 ++++++++++++++-------
 14 files changed, 135 insertions(+), 88 deletions(-)

-- 
1.8.3.2

[PATCH v9 1/9] mfd: omap-usb-host: Get clocks based on hardware revision

[Roger Quadros]

Not all revisions have all the clocks so get the necessary clocks
based on hardware revision.

This should avoid un-necessary clk_get failure messages that were
observed earlier.

Also remove the dummy USB host clocks from the OMAP3 clock data.
These are no longer expected by the driver.

CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
CC: Tero Kristo <t-kristo@ti.com>
Acked-by: Mike Turquette <mturquette@linaro.org> [OMAP3 CLK data]
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 arch/arm/mach-omap2/cclock3xxx_data.c |  4 ----
 drivers/clk/ti/clk-3xxx.c             |  4 ----
 drivers/mfd/omap-usb-host.c           | 43 ++++++++++++++++++++++++++---------
 3 files changed, 32 insertions(+), 19 deletions(-)

diff --git a/arch/arm/mach-omap2/cclock3xxx_data.c b/arch/arm/mach-omap2/cclock3xxx_data.c
index 3b05aea..4299a55 100644
--- a/arch/arm/mach-omap2/cclock3xxx_data.c
+++ b/arch/arm/mach-omap2/cclock3xxx_data.c
@@ -3495,10 +3495,6 @@ static struct omap_clk omap3xxx_clks[] = {
 	CLK(NULL,	"dss_tv_fck",	&dss_tv_fck),
 	CLK(NULL,	"dss_96m_fck",	&dss_96m_fck),
 	CLK(NULL,	"dss2_alwon_fck",	&dss2_alwon_fck),
-	CLK(NULL,	"utmi_p1_gfclk",	&dummy_ck),
-	CLK(NULL,	"utmi_p2_gfclk",	&dummy_ck),
-	CLK(NULL,	"xclk60mhsp1_ck",	&dummy_ck),
-	CLK(NULL,	"xclk60mhsp2_ck",	&dummy_ck),
 	CLK(NULL,	"init_60m_fclk",	&dummy_ck),
 	CLK(NULL,	"gpt1_fck",	&gpt1_fck),
 	CLK(NULL,	"aes2_ick",	&aes2_ick),
diff --git a/drivers/clk/ti/clk-3xxx.c b/drivers/clk/ti/clk-3xxx.c
index d323023..0d1750a 100644
--- a/drivers/clk/ti/clk-3xxx.c
+++ b/drivers/clk/ti/clk-3xxx.c
@@ -130,10 +130,6 @@ static struct ti_dt_clk omap3xxx_clks[] = {
 	DT_CLK(NULL, "dss_tv_fck", "dss_tv_fck"),
 	DT_CLK(NULL, "dss_96m_fck", "dss_96m_fck"),
 	DT_CLK(NULL, "dss2_alwon_fck", "dss2_alwon_fck"),
-	DT_CLK(NULL, "utmi_p1_gfclk", "dummy_ck"),
-	DT_CLK(NULL, "utmi_p2_gfclk", "dummy_ck"),
-	DT_CLK(NULL, "xclk60mhsp1_ck", "dummy_ck"),
-	DT_CLK(NULL, "xclk60mhsp2_ck", "dummy_ck"),
 	DT_CLK(NULL, "init_60m_fclk", "dummy_ck"),
 	DT_CLK(NULL, "gpt1_fck", "gpt1_fck"),
 	DT_CLK(NULL, "aes2_ick", "aes2_ick"),
diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index 0c3c9a0..c63bfdf 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -665,22 +665,43 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 		goto err_mem;
 	}
 
-	need_logic_fck = false;
+	/* Set all clocks as invalid to begin with */
+	omap->ehci_logic_fck = ERR_PTR(-ENODEV);
+	omap->init_60m_fclk = ERR_PTR(-ENODEV);
+	omap->utmi_p1_gfclk = ERR_PTR(-ENODEV);
+	omap->utmi_p2_gfclk = ERR_PTR(-ENODEV);
+	omap->xclk60mhsp1_ck = ERR_PTR(-ENODEV);
+	omap->xclk60mhsp2_ck = ERR_PTR(-ENODEV);
+
 	for (i = 0; i < omap->nports; i++) {
-		if (is_ehci_phy_mode(i) || is_ehci_tll_mode(i) ||
-			is_ehci_hsic_mode(i))
-				need_logic_fck |= true;
+		omap->utmi_clk[i] = ERR_PTR(-ENODEV);
+		omap->hsic480m_clk[i] = ERR_PTR(-ENODEV);
+		omap->hsic60m_clk[i] = ERR_PTR(-ENODEV);
 	}
 
-	omap->ehci_logic_fck = ERR_PTR(-EINVAL);
-	if (need_logic_fck) {
-		omap->ehci_logic_fck = devm_clk_get(dev, "ehci_logic_fck");
-		if (IS_ERR(omap->ehci_logic_fck)) {
-			ret = PTR_ERR(omap->ehci_logic_fck);
-			dev_dbg(dev, "ehci_logic_fck failed:%d\n", ret);
+	/* for OMAP3 i.e. USBHS REV1 */
+	if (omap->usbhs_rev == OMAP_USBHS_REV1) {
+		need_logic_fck = false;
+		for (i = 0; i < omap->nports; i++) {
+			if (is_ehci_phy_mode(pdata->port_mode[i]) ||
+			    is_ehci_tll_mode(pdata->port_mode[i]) ||
+			    is_ehci_hsic_mode(pdata->port_mode[i]))
+
+				need_logic_fck |= true;
+		}
+
+		if (need_logic_fck) {
+			omap->ehci_logic_fck = devm_clk_get(dev,
+							    "ehci_logic_fck");
+			if (IS_ERR(omap->ehci_logic_fck)) {
+				ret = PTR_ERR(omap->ehci_logic_fck);
+				dev_dbg(dev, "ehci_logic_fck failed:%d\n", ret);
+			}
 		}
+		goto initialize;
 	}
 
+	/* for OMAP4+ i.e. USBHS REV2+ */
 	omap->utmi_p1_gfclk = devm_clk_get(dev, "utmi_p1_gfclk");
 	if (IS_ERR(omap->utmi_p1_gfclk)) {
 		ret = PTR_ERR(omap->utmi_p1_gfclk);
@@ -748,7 +769,6 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 	}
 
 	if (is_ehci_phy_mode(pdata->port_mode[0])) {
-		/* for OMAP3, clk_set_parent fails */
 		ret = clk_set_parent(omap->utmi_p1_gfclk,
 					omap->xclk60mhsp1_ck);
 		if (ret != 0)
@@ -776,6 +796,7 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 					ret);
 	}
 
+initialize:
 	omap_usbhs_init(dev);
 
 	if (dev->of_node) {
-- 
1.8.3.2

[PATCH v9 1/9] mfd: omap-usb-host: Get clocks based on hardware revision

[Roger Quadros]

Not all revisions have all the clocks so get the necessary clocks
based on hardware revision.

This should avoid un-necessary clk_get failure messages that were
observed earlier.

Also remove the dummy USB host clocks from the OMAP3 clock data.
These are no longer expected by the driver.

CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
CC: Tero Kristo <t-kristo@ti.com>
Acked-by: Mike Turquette <mturquette@linaro.org> [OMAP3 CLK data]
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 arch/arm/mach-omap2/cclock3xxx_data.c |  4 ----
 drivers/clk/ti/clk-3xxx.c             |  4 ----
 drivers/mfd/omap-usb-host.c           | 43 ++++++++++++++++++++++++++---------
 3 files changed, 32 insertions(+), 19 deletions(-)

diff --git a/arch/arm/mach-omap2/cclock3xxx_data.c b/arch/arm/mach-omap2/cclock3xxx_data.c
index 3b05aea..4299a55 100644
--- a/arch/arm/mach-omap2/cclock3xxx_data.c
+++ b/arch/arm/mach-omap2/cclock3xxx_data.c
@@ -3495,10 +3495,6 @@ static struct omap_clk omap3xxx_clks[] = {
 	CLK(NULL,	"dss_tv_fck",	&dss_tv_fck),
 	CLK(NULL,	"dss_96m_fck",	&dss_96m_fck),
 	CLK(NULL,	"dss2_alwon_fck",	&dss2_alwon_fck),
-	CLK(NULL,	"utmi_p1_gfclk",	&dummy_ck),
-	CLK(NULL,	"utmi_p2_gfclk",	&dummy_ck),
-	CLK(NULL,	"xclk60mhsp1_ck",	&dummy_ck),
-	CLK(NULL,	"xclk60mhsp2_ck",	&dummy_ck),
 	CLK(NULL,	"init_60m_fclk",	&dummy_ck),
 	CLK(NULL,	"gpt1_fck",	&gpt1_fck),
 	CLK(NULL,	"aes2_ick",	&aes2_ick),
diff --git a/drivers/clk/ti/clk-3xxx.c b/drivers/clk/ti/clk-3xxx.c
index d323023..0d1750a 100644
--- a/drivers/clk/ti/clk-3xxx.c
+++ b/drivers/clk/ti/clk-3xxx.c
@@ -130,10 +130,6 @@ static struct ti_dt_clk omap3xxx_clks[] = {
 	DT_CLK(NULL, "dss_tv_fck", "dss_tv_fck"),
 	DT_CLK(NULL, "dss_96m_fck", "dss_96m_fck"),
 	DT_CLK(NULL, "dss2_alwon_fck", "dss2_alwon_fck"),
-	DT_CLK(NULL, "utmi_p1_gfclk", "dummy_ck"),
-	DT_CLK(NULL, "utmi_p2_gfclk", "dummy_ck"),
-	DT_CLK(NULL, "xclk60mhsp1_ck", "dummy_ck"),
-	DT_CLK(NULL, "xclk60mhsp2_ck", "dummy_ck"),
 	DT_CLK(NULL, "init_60m_fclk", "dummy_ck"),
 	DT_CLK(NULL, "gpt1_fck", "gpt1_fck"),
 	DT_CLK(NULL, "aes2_ick", "aes2_ick"),
diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index 0c3c9a0..c63bfdf 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -665,22 +665,43 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 		goto err_mem;
 	}
 
-	need_logic_fck = false;
+	/* Set all clocks as invalid to begin with */
+	omap->ehci_logic_fck = ERR_PTR(-ENODEV);
+	omap->init_60m_fclk = ERR_PTR(-ENODEV);
+	omap->utmi_p1_gfclk = ERR_PTR(-ENODEV);
+	omap->utmi_p2_gfclk = ERR_PTR(-ENODEV);
+	omap->xclk60mhsp1_ck = ERR_PTR(-ENODEV);
+	omap->xclk60mhsp2_ck = ERR_PTR(-ENODEV);
+
 	for (i = 0; i < omap->nports; i++) {
-		if (is_ehci_phy_mode(i) || is_ehci_tll_mode(i) ||
-			is_ehci_hsic_mode(i))
-				need_logic_fck |= true;
+		omap->utmi_clk[i] = ERR_PTR(-ENODEV);
+		omap->hsic480m_clk[i] = ERR_PTR(-ENODEV);
+		omap->hsic60m_clk[i] = ERR_PTR(-ENODEV);
 	}
 
-	omap->ehci_logic_fck = ERR_PTR(-EINVAL);
-	if (need_logic_fck) {
-		omap->ehci_logic_fck = devm_clk_get(dev, "ehci_logic_fck");
-		if (IS_ERR(omap->ehci_logic_fck)) {
-			ret = PTR_ERR(omap->ehci_logic_fck);
-			dev_dbg(dev, "ehci_logic_fck failed:%d\n", ret);
+	/* for OMAP3 i.e. USBHS REV1 */
+	if (omap->usbhs_rev == OMAP_USBHS_REV1) {
+		need_logic_fck = false;
+		for (i = 0; i < omap->nports; i++) {
+			if (is_ehci_phy_mode(pdata->port_mode[i]) ||
+			    is_ehci_tll_mode(pdata->port_mode[i]) ||
+			    is_ehci_hsic_mode(pdata->port_mode[i]))
+
+				need_logic_fck |= true;
+		}
+
+		if (need_logic_fck) {
+			omap->ehci_logic_fck = devm_clk_get(dev,
+							    "ehci_logic_fck");
+			if (IS_ERR(omap->ehci_logic_fck)) {
+				ret = PTR_ERR(omap->ehci_logic_fck);
+				dev_dbg(dev, "ehci_logic_fck failed:%d\n", ret);
+			}
 		}
+		goto initialize;
 	}
 
+	/* for OMAP4+ i.e. USBHS REV2+ */
 	omap->utmi_p1_gfclk = devm_clk_get(dev, "utmi_p1_gfclk");
 	if (IS_ERR(omap->utmi_p1_gfclk)) {
 		ret = PTR_ERR(omap->utmi_p1_gfclk);
@@ -748,7 +769,6 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 	}
 
 	if (is_ehci_phy_mode(pdata->port_mode[0])) {
-		/* for OMAP3, clk_set_parent fails */
 		ret = clk_set_parent(omap->utmi_p1_gfclk,
 					omap->xclk60mhsp1_ck);
 		if (ret != 0)
@@ -776,6 +796,7 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 					ret);
 	}
 
+initialize:
 	omap_usbhs_init(dev);
 
 	if (dev->of_node) {
-- 
1.8.3.2

[PATCH v9 1/9] mfd: omap-usb-host: Get clocks based on hardware revision

[Roger Quadros]

Not all revisions have all the clocks so get the necessary clocks
based on hardware revision.

This should avoid un-necessary clk_get failure messages that were
observed earlier.

Also remove the dummy USB host clocks from the OMAP3 clock data.
These are no longer expected by the driver.

CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
CC: Tero Kristo <t-kristo@ti.com>
Acked-by: Mike Turquette <mturquette@linaro.org> [OMAP3 CLK data]
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 arch/arm/mach-omap2/cclock3xxx_data.c |  4 ----
 drivers/clk/ti/clk-3xxx.c             |  4 ----
 drivers/mfd/omap-usb-host.c           | 43 ++++++++++++++++++++++++++---------
 3 files changed, 32 insertions(+), 19 deletions(-)

diff --git a/arch/arm/mach-omap2/cclock3xxx_data.c b/arch/arm/mach-omap2/cclock3xxx_data.c
index 3b05aea..4299a55 100644
--- a/arch/arm/mach-omap2/cclock3xxx_data.c
+++ b/arch/arm/mach-omap2/cclock3xxx_data.c
@@ -3495,10 +3495,6 @@ static struct omap_clk omap3xxx_clks[] = {
 	CLK(NULL,	"dss_tv_fck",	&dss_tv_fck),
 	CLK(NULL,	"dss_96m_fck",	&dss_96m_fck),
 	CLK(NULL,	"dss2_alwon_fck",	&dss2_alwon_fck),
-	CLK(NULL,	"utmi_p1_gfclk",	&dummy_ck),
-	CLK(NULL,	"utmi_p2_gfclk",	&dummy_ck),
-	CLK(NULL,	"xclk60mhsp1_ck",	&dummy_ck),
-	CLK(NULL,	"xclk60mhsp2_ck",	&dummy_ck),
 	CLK(NULL,	"init_60m_fclk",	&dummy_ck),
 	CLK(NULL,	"gpt1_fck",	&gpt1_fck),
 	CLK(NULL,	"aes2_ick",	&aes2_ick),
diff --git a/drivers/clk/ti/clk-3xxx.c b/drivers/clk/ti/clk-3xxx.c
index d323023..0d1750a 100644
--- a/drivers/clk/ti/clk-3xxx.c
+++ b/drivers/clk/ti/clk-3xxx.c
@@ -130,10 +130,6 @@ static struct ti_dt_clk omap3xxx_clks[] = {
 	DT_CLK(NULL, "dss_tv_fck", "dss_tv_fck"),
 	DT_CLK(NULL, "dss_96m_fck", "dss_96m_fck"),
 	DT_CLK(NULL, "dss2_alwon_fck", "dss2_alwon_fck"),
-	DT_CLK(NULL, "utmi_p1_gfclk", "dummy_ck"),
-	DT_CLK(NULL, "utmi_p2_gfclk", "dummy_ck"),
-	DT_CLK(NULL, "xclk60mhsp1_ck", "dummy_ck"),
-	DT_CLK(NULL, "xclk60mhsp2_ck", "dummy_ck"),
 	DT_CLK(NULL, "init_60m_fclk", "dummy_ck"),
 	DT_CLK(NULL, "gpt1_fck", "gpt1_fck"),
 	DT_CLK(NULL, "aes2_ick", "aes2_ick"),
diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index 0c3c9a0..c63bfdf 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -665,22 +665,43 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 		goto err_mem;
 	}
 
-	need_logic_fck = false;
+	/* Set all clocks as invalid to begin with */
+	omap->ehci_logic_fck = ERR_PTR(-ENODEV);
+	omap->init_60m_fclk = ERR_PTR(-ENODEV);
+	omap->utmi_p1_gfclk = ERR_PTR(-ENODEV);
+	omap->utmi_p2_gfclk = ERR_PTR(-ENODEV);
+	omap->xclk60mhsp1_ck = ERR_PTR(-ENODEV);
+	omap->xclk60mhsp2_ck = ERR_PTR(-ENODEV);
+
 	for (i = 0; i < omap->nports; i++) {
-		if (is_ehci_phy_mode(i) || is_ehci_tll_mode(i) ||
-			is_ehci_hsic_mode(i))
-				need_logic_fck |= true;
+		omap->utmi_clk[i] = ERR_PTR(-ENODEV);
+		omap->hsic480m_clk[i] = ERR_PTR(-ENODEV);
+		omap->hsic60m_clk[i] = ERR_PTR(-ENODEV);
 	}
 
-	omap->ehci_logic_fck = ERR_PTR(-EINVAL);
-	if (need_logic_fck) {
-		omap->ehci_logic_fck = devm_clk_get(dev, "ehci_logic_fck");
-		if (IS_ERR(omap->ehci_logic_fck)) {
-			ret = PTR_ERR(omap->ehci_logic_fck);
-			dev_dbg(dev, "ehci_logic_fck failed:%d\n", ret);
+	/* for OMAP3 i.e. USBHS REV1 */
+	if (omap->usbhs_rev == OMAP_USBHS_REV1) {
+		need_logic_fck = false;
+		for (i = 0; i < omap->nports; i++) {
+			if (is_ehci_phy_mode(pdata->port_mode[i]) ||
+			    is_ehci_tll_mode(pdata->port_mode[i]) ||
+			    is_ehci_hsic_mode(pdata->port_mode[i]))
+
+				need_logic_fck |= true;
+		}
+
+		if (need_logic_fck) {
+			omap->ehci_logic_fck = devm_clk_get(dev,
+							    "ehci_logic_fck");
+			if (IS_ERR(omap->ehci_logic_fck)) {
+				ret = PTR_ERR(omap->ehci_logic_fck);
+				dev_dbg(dev, "ehci_logic_fck failed:%d\n", ret);
+			}
 		}
+		goto initialize;
 	}
 
+	/* for OMAP4+ i.e. USBHS REV2+ */
 	omap->utmi_p1_gfclk = devm_clk_get(dev, "utmi_p1_gfclk");
 	if (IS_ERR(omap->utmi_p1_gfclk)) {
 		ret = PTR_ERR(omap->utmi_p1_gfclk);
@@ -748,7 +769,6 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 	}
 
 	if (is_ehci_phy_mode(pdata->port_mode[0])) {
-		/* for OMAP3, clk_set_parent fails */
 		ret = clk_set_parent(omap->utmi_p1_gfclk,
 					omap->xclk60mhsp1_ck);
 		if (ret != 0)
@@ -776,6 +796,7 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 					ret);
 	}
 
+initialize:
 	omap_usbhs_init(dev);
 
 	if (dev->of_node) {
-- 
1.8.3.2

[PATCH v9 2/9] mfd: omap-usb-host: Always fail on clk_get() error

[Roger Quadros]

Be more strict and always fail on clk_get() error.

CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 drivers/mfd/omap-usb-host.c | 62 +++++++++++++++++++++++++++++----------------
 1 file changed, 40 insertions(+), 22 deletions(-)

diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index c63bfdf..c31baa7 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -695,7 +695,8 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 							    "ehci_logic_fck");
 			if (IS_ERR(omap->ehci_logic_fck)) {
 				ret = PTR_ERR(omap->ehci_logic_fck);
-				dev_dbg(dev, "ehci_logic_fck failed:%d\n", ret);
+				dev_err(dev, "ehci_logic_fck failed:%d\n", ret);
+				goto err_mem;
 			}
 		}
 		goto initialize;
@@ -749,51 +750,68 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 		 * them
 		 */
 		omap->utmi_clk[i] = devm_clk_get(dev, clkname);
-		if (IS_ERR(omap->utmi_clk[i]))
-			dev_dbg(dev, "Failed to get clock : %s : %ld\n",
-				clkname, PTR_ERR(omap->utmi_clk[i]));
+		if (IS_ERR(omap->utmi_clk[i])) {
+			ret = PTR_ERR(omap->utmi_clk[i]);
+			dev_err(dev, "Failed to get clock : %s : %d\n",
+				clkname, ret);
+			goto err_mem;
+		}
 
 		snprintf(clkname, sizeof(clkname),
 				"usb_host_hs_hsic480m_p%d_clk", i + 1);
 		omap->hsic480m_clk[i] = devm_clk_get(dev, clkname);
-		if (IS_ERR(omap->hsic480m_clk[i]))
-			dev_dbg(dev, "Failed to get clock : %s : %ld\n",
-				clkname, PTR_ERR(omap->hsic480m_clk[i]));
+		if (IS_ERR(omap->hsic480m_clk[i])) {
+			ret = PTR_ERR(omap->hsic480m_clk[i]);
+			dev_err(dev, "Failed to get clock : %s : %d\n",
+				clkname, ret);
+			goto err_mem;
+		}
 
 		snprintf(clkname, sizeof(clkname),
 				"usb_host_hs_hsic60m_p%d_clk", i + 1);
 		omap->hsic60m_clk[i] = devm_clk_get(dev, clkname);
-		if (IS_ERR(omap->hsic60m_clk[i]))
-			dev_dbg(dev, "Failed to get clock : %s : %ld\n",
-				clkname, PTR_ERR(omap->hsic60m_clk[i]));
+		if (IS_ERR(omap->hsic60m_clk[i])) {
+			ret = PTR_ERR(omap->hsic60m_clk[i]);
+			dev_err(dev, "Failed to get clock : %s : %d\n",
+				clkname, ret);
+			goto err_mem;
+		}
 	}
 
 	if (is_ehci_phy_mode(pdata->port_mode[0])) {
 		ret = clk_set_parent(omap->utmi_p1_gfclk,
 					omap->xclk60mhsp1_ck);
-		if (ret != 0)
-			dev_dbg(dev, "xclk60mhsp1_ck set parent failed: %d\n",
-					ret);
+		if (ret != 0) {
+			dev_err(dev, "xclk60mhsp1_ck set parent failed: %d\n",
+				ret);
+			goto err_mem;
+		}
 	} else if (is_ehci_tll_mode(pdata->port_mode[0])) {
 		ret = clk_set_parent(omap->utmi_p1_gfclk,
 					omap->init_60m_fclk);
-		if (ret != 0)
-			dev_dbg(dev, "P0 init_60m_fclk set parent failed: %d\n",
-					ret);
+		if (ret != 0) {
+			dev_err(dev, "P0 init_60m_fclk set parent failed: %d\n",
+				ret);
+			goto err_mem;
+		}
 	}
 
 	if (is_ehci_phy_mode(pdata->port_mode[1])) {
 		ret = clk_set_parent(omap->utmi_p2_gfclk,
 					omap->xclk60mhsp2_ck);
-		if (ret != 0)
-			dev_dbg(dev, "xclk60mhsp2_ck set parent failed: %d\n",
-					ret);
+		if (ret != 0) {
+			dev_err(dev, "xclk60mhsp2_ck set parent failed: %d\n",
+				ret);
+			goto err_mem;
+		}
 	} else if (is_ehci_tll_mode(pdata->port_mode[1])) {
 		ret = clk_set_parent(omap->utmi_p2_gfclk,
 						omap->init_60m_fclk);
-		if (ret != 0)
-			dev_dbg(dev, "P1 init_60m_fclk set parent failed: %d\n",
-					ret);
+		if (ret != 0) {
+			dev_err(dev, "P1 init_60m_fclk set parent failed: %d\n",
+				ret);
+			goto err_mem;
+		}
 	}
 
 initialize:
-- 
1.8.3.2

[PATCH v9 2/9] mfd: omap-usb-host: Always fail on clk_get() error

[Roger Quadros]

Be more strict and always fail on clk_get() error.

CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 drivers/mfd/omap-usb-host.c | 62 +++++++++++++++++++++++++++++----------------
 1 file changed, 40 insertions(+), 22 deletions(-)

diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index c63bfdf..c31baa7 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -695,7 +695,8 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 							    "ehci_logic_fck");
 			if (IS_ERR(omap->ehci_logic_fck)) {
 				ret = PTR_ERR(omap->ehci_logic_fck);
-				dev_dbg(dev, "ehci_logic_fck failed:%d\n", ret);
+				dev_err(dev, "ehci_logic_fck failed:%d\n", ret);
+				goto err_mem;
 			}
 		}
 		goto initialize;
@@ -749,51 +750,68 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 		 * them
 		 */
 		omap->utmi_clk[i] = devm_clk_get(dev, clkname);
-		if (IS_ERR(omap->utmi_clk[i]))
-			dev_dbg(dev, "Failed to get clock : %s : %ld\n",
-				clkname, PTR_ERR(omap->utmi_clk[i]));
+		if (IS_ERR(omap->utmi_clk[i])) {
+			ret = PTR_ERR(omap->utmi_clk[i]);
+			dev_err(dev, "Failed to get clock : %s : %d\n",
+				clkname, ret);
+			goto err_mem;
+		}
 
 		snprintf(clkname, sizeof(clkname),
 				"usb_host_hs_hsic480m_p%d_clk", i + 1);
 		omap->hsic480m_clk[i] = devm_clk_get(dev, clkname);
-		if (IS_ERR(omap->hsic480m_clk[i]))
-			dev_dbg(dev, "Failed to get clock : %s : %ld\n",
-				clkname, PTR_ERR(omap->hsic480m_clk[i]));
+		if (IS_ERR(omap->hsic480m_clk[i])) {
+			ret = PTR_ERR(omap->hsic480m_clk[i]);
+			dev_err(dev, "Failed to get clock : %s : %d\n",
+				clkname, ret);
+			goto err_mem;
+		}
 
 		snprintf(clkname, sizeof(clkname),
 				"usb_host_hs_hsic60m_p%d_clk", i + 1);
 		omap->hsic60m_clk[i] = devm_clk_get(dev, clkname);
-		if (IS_ERR(omap->hsic60m_clk[i]))
-			dev_dbg(dev, "Failed to get clock : %s : %ld\n",
-				clkname, PTR_ERR(omap->hsic60m_clk[i]));
+		if (IS_ERR(omap->hsic60m_clk[i])) {
+			ret = PTR_ERR(omap->hsic60m_clk[i]);
+			dev_err(dev, "Failed to get clock : %s : %d\n",
+				clkname, ret);
+			goto err_mem;
+		}
 	}
 
 	if (is_ehci_phy_mode(pdata->port_mode[0])) {
 		ret = clk_set_parent(omap->utmi_p1_gfclk,
 					omap->xclk60mhsp1_ck);
-		if (ret != 0)
-			dev_dbg(dev, "xclk60mhsp1_ck set parent failed: %d\n",
-					ret);
+		if (ret != 0) {
+			dev_err(dev, "xclk60mhsp1_ck set parent failed: %d\n",
+				ret);
+			goto err_mem;
+		}
 	} else if (is_ehci_tll_mode(pdata->port_mode[0])) {
 		ret = clk_set_parent(omap->utmi_p1_gfclk,
 					omap->init_60m_fclk);
-		if (ret != 0)
-			dev_dbg(dev, "P0 init_60m_fclk set parent failed: %d\n",
-					ret);
+		if (ret != 0) {
+			dev_err(dev, "P0 init_60m_fclk set parent failed: %d\n",
+				ret);
+			goto err_mem;
+		}
 	}
 
 	if (is_ehci_phy_mode(pdata->port_mode[1])) {
 		ret = clk_set_parent(omap->utmi_p2_gfclk,
 					omap->xclk60mhsp2_ck);
-		if (ret != 0)
-			dev_dbg(dev, "xclk60mhsp2_ck set parent failed: %d\n",
-					ret);
+		if (ret != 0) {
+			dev_err(dev, "xclk60mhsp2_ck set parent failed: %d\n",
+				ret);
+			goto err_mem;
+		}
 	} else if (is_ehci_tll_mode(pdata->port_mode[1])) {
 		ret = clk_set_parent(omap->utmi_p2_gfclk,
 						omap->init_60m_fclk);
-		if (ret != 0)
-			dev_dbg(dev, "P1 init_60m_fclk set parent failed: %d\n",
-					ret);
+		if (ret != 0) {
+			dev_err(dev, "P1 init_60m_fclk set parent failed: %d\n",
+				ret);
+			goto err_mem;
+		}
 	}
 
 initialize:
-- 
1.8.3.2

[PATCH v9 2/9] mfd: omap-usb-host: Always fail on clk_get() error

[Roger Quadros]

Be more strict and always fail on clk_get() error.

CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 drivers/mfd/omap-usb-host.c | 62 +++++++++++++++++++++++++++++----------------
 1 file changed, 40 insertions(+), 22 deletions(-)

diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index c63bfdf..c31baa7 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -695,7 +695,8 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 							    "ehci_logic_fck");
 			if (IS_ERR(omap->ehci_logic_fck)) {
 				ret = PTR_ERR(omap->ehci_logic_fck);
-				dev_dbg(dev, "ehci_logic_fck failed:%d\n", ret);
+				dev_err(dev, "ehci_logic_fck failed:%d\n", ret);
+				goto err_mem;
 			}
 		}
 		goto initialize;
@@ -749,51 +750,68 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 		 * them
 		 */
 		omap->utmi_clk[i] = devm_clk_get(dev, clkname);
-		if (IS_ERR(omap->utmi_clk[i]))
-			dev_dbg(dev, "Failed to get clock : %s : %ld\n",
-				clkname, PTR_ERR(omap->utmi_clk[i]));
+		if (IS_ERR(omap->utmi_clk[i])) {
+			ret = PTR_ERR(omap->utmi_clk[i]);
+			dev_err(dev, "Failed to get clock : %s : %d\n",
+				clkname, ret);
+			goto err_mem;
+		}
 
 		snprintf(clkname, sizeof(clkname),
 				"usb_host_hs_hsic480m_p%d_clk", i + 1);
 		omap->hsic480m_clk[i] = devm_clk_get(dev, clkname);
-		if (IS_ERR(omap->hsic480m_clk[i]))
-			dev_dbg(dev, "Failed to get clock : %s : %ld\n",
-				clkname, PTR_ERR(omap->hsic480m_clk[i]));
+		if (IS_ERR(omap->hsic480m_clk[i])) {
+			ret = PTR_ERR(omap->hsic480m_clk[i]);
+			dev_err(dev, "Failed to get clock : %s : %d\n",
+				clkname, ret);
+			goto err_mem;
+		}
 
 		snprintf(clkname, sizeof(clkname),
 				"usb_host_hs_hsic60m_p%d_clk", i + 1);
 		omap->hsic60m_clk[i] = devm_clk_get(dev, clkname);
-		if (IS_ERR(omap->hsic60m_clk[i]))
-			dev_dbg(dev, "Failed to get clock : %s : %ld\n",
-				clkname, PTR_ERR(omap->hsic60m_clk[i]));
+		if (IS_ERR(omap->hsic60m_clk[i])) {
+			ret = PTR_ERR(omap->hsic60m_clk[i]);
+			dev_err(dev, "Failed to get clock : %s : %d\n",
+				clkname, ret);
+			goto err_mem;
+		}
 	}
 
 	if (is_ehci_phy_mode(pdata->port_mode[0])) {
 		ret = clk_set_parent(omap->utmi_p1_gfclk,
 					omap->xclk60mhsp1_ck);
-		if (ret != 0)
-			dev_dbg(dev, "xclk60mhsp1_ck set parent failed: %d\n",
-					ret);
+		if (ret != 0) {
+			dev_err(dev, "xclk60mhsp1_ck set parent failed: %d\n",
+				ret);
+			goto err_mem;
+		}
 	} else if (is_ehci_tll_mode(pdata->port_mode[0])) {
 		ret = clk_set_parent(omap->utmi_p1_gfclk,
 					omap->init_60m_fclk);
-		if (ret != 0)
-			dev_dbg(dev, "P0 init_60m_fclk set parent failed: %d\n",
-					ret);
+		if (ret != 0) {
+			dev_err(dev, "P0 init_60m_fclk set parent failed: %d\n",
+				ret);
+			goto err_mem;
+		}
 	}
 
 	if (is_ehci_phy_mode(pdata->port_mode[1])) {
 		ret = clk_set_parent(omap->utmi_p2_gfclk,
 					omap->xclk60mhsp2_ck);
-		if (ret != 0)
-			dev_dbg(dev, "xclk60mhsp2_ck set parent failed: %d\n",
-					ret);
+		if (ret != 0) {
+			dev_err(dev, "xclk60mhsp2_ck set parent failed: %d\n",
+				ret);
+			goto err_mem;
+		}
 	} else if (is_ehci_tll_mode(pdata->port_mode[1])) {
 		ret = clk_set_parent(omap->utmi_p2_gfclk,
 						omap->init_60m_fclk);
-		if (ret != 0)
-			dev_dbg(dev, "P1 init_60m_fclk set parent failed: %d\n",
-					ret);
+		if (ret != 0) {
+			dev_err(dev, "P1 init_60m_fclk set parent failed: %d\n",
+				ret);
+			goto err_mem;
+		}
 	}
 
 initialize:
-- 
1.8.3.2

[PATCH v9 3/9] mfd: omap-usb-host: Use proper clock name instead of alias

[Roger Quadros]

Use the proper clock name 'usbhost_120m_fck' instead of the
alias 'ehci_logic_fck'

Get rid of the 'ehci_logic_fck' alias from the OMAP3 hwmod data
as well.

CC: Paul Walmsley <paul@pwsan.com>
CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 6 ------
 drivers/mfd/omap-usb-host.c                | 5 +++--
 2 files changed, 3 insertions(+), 8 deletions(-)

diff --git a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
index 4c3b1e6..ad87f46 100644
--- a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
@@ -1955,10 +1955,6 @@ static struct omap_hwmod_class omap3xxx_usb_host_hs_hwmod_class = {
 	.sysc = &omap3xxx_usb_host_hs_sysc,
 };
 
-static struct omap_hwmod_opt_clk omap3xxx_usb_host_hs_opt_clks[] = {
-	  { .role = "ehci_logic_fck", .clk = "usbhost_120m_fck", },
-};
-
 static struct omap_hwmod_irq_info omap3xxx_usb_host_hs_irqs[] = {
 	{ .name = "ohci-irq", .irq = 76 + OMAP_INTC_START, },
 	{ .name = "ehci-irq", .irq = 77 + OMAP_INTC_START, },
@@ -1981,8 +1977,6 @@ static struct omap_hwmod omap3xxx_usb_host_hs_hwmod = {
 			.idlest_stdby_bit = OMAP3430ES2_ST_USBHOST_STDBY_SHIFT,
 		},
 	},
-	.opt_clks	= omap3xxx_usb_host_hs_opt_clks,
-	.opt_clks_cnt	= ARRAY_SIZE(omap3xxx_usb_host_hs_opt_clks),
 
 	/*
 	 * Errata: USBHOST Configured In Smart-Idle Can Lead To a Deadlock
diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index c31baa7..865c276 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -692,10 +692,11 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 
 		if (need_logic_fck) {
 			omap->ehci_logic_fck = devm_clk_get(dev,
-							    "ehci_logic_fck");
+							    "usbhost_120m_fck");
 			if (IS_ERR(omap->ehci_logic_fck)) {
 				ret = PTR_ERR(omap->ehci_logic_fck);
-				dev_err(dev, "ehci_logic_fck failed:%d\n", ret);
+				dev_err(dev, "usbhost_120m_fck failed:%d\n",
+					ret);
 				goto err_mem;
 			}
 		}
-- 
1.8.3.2

[PATCH v9 3/9] mfd: omap-usb-host: Use proper clock name instead of alias

[Roger Quadros]

Use the proper clock name 'usbhost_120m_fck' instead of the
alias 'ehci_logic_fck'

Get rid of the 'ehci_logic_fck' alias from the OMAP3 hwmod data
as well.

CC: Paul Walmsley <paul@pwsan.com>
CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 6 ------
 drivers/mfd/omap-usb-host.c                | 5 +++--
 2 files changed, 3 insertions(+), 8 deletions(-)

diff --git a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
index 4c3b1e6..ad87f46 100644
--- a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
@@ -1955,10 +1955,6 @@ static struct omap_hwmod_class omap3xxx_usb_host_hs_hwmod_class = {
 	.sysc = &omap3xxx_usb_host_hs_sysc,
 };
 
-static struct omap_hwmod_opt_clk omap3xxx_usb_host_hs_opt_clks[] = {
-	  { .role = "ehci_logic_fck", .clk = "usbhost_120m_fck", },
-};
-
 static struct omap_hwmod_irq_info omap3xxx_usb_host_hs_irqs[] = {
 	{ .name = "ohci-irq", .irq = 76 + OMAP_INTC_START, },
 	{ .name = "ehci-irq", .irq = 77 + OMAP_INTC_START, },
@@ -1981,8 +1977,6 @@ static struct omap_hwmod omap3xxx_usb_host_hs_hwmod = {
 			.idlest_stdby_bit = OMAP3430ES2_ST_USBHOST_STDBY_SHIFT,
 		},
 	},
-	.opt_clks	= omap3xxx_usb_host_hs_opt_clks,
-	.opt_clks_cnt	= ARRAY_SIZE(omap3xxx_usb_host_hs_opt_clks),
 
 	/*
 	 * Errata: USBHOST Configured In Smart-Idle Can Lead To a Deadlock
diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index c31baa7..865c276 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -692,10 +692,11 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 
 		if (need_logic_fck) {
 			omap->ehci_logic_fck = devm_clk_get(dev,
-							    "ehci_logic_fck");
+							    "usbhost_120m_fck");
 			if (IS_ERR(omap->ehci_logic_fck)) {
 				ret = PTR_ERR(omap->ehci_logic_fck);
-				dev_err(dev, "ehci_logic_fck failed:%d\n", ret);
+				dev_err(dev, "usbhost_120m_fck failed:%d\n",
+					ret);
 				goto err_mem;
 			}
 		}
-- 
1.8.3.2

[PATCH v9 3/9] mfd: omap-usb-host: Use proper clock name instead of alias

[Roger Quadros]

Use the proper clock name 'usbhost_120m_fck' instead of the
alias 'ehci_logic_fck'

Get rid of the 'ehci_logic_fck' alias from the OMAP3 hwmod data
as well.

CC: Paul Walmsley <paul@pwsan.com>
CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 6 ------
 drivers/mfd/omap-usb-host.c                | 5 +++--
 2 files changed, 3 insertions(+), 8 deletions(-)

diff --git a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
index 4c3b1e6..ad87f46 100644
--- a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
@@ -1955,10 +1955,6 @@ static struct omap_hwmod_class omap3xxx_usb_host_hs_hwmod_class = {
 	.sysc = &omap3xxx_usb_host_hs_sysc,
 };
 
-static struct omap_hwmod_opt_clk omap3xxx_usb_host_hs_opt_clks[] = {
-	  { .role = "ehci_logic_fck", .clk = "usbhost_120m_fck", },
-};
-
 static struct omap_hwmod_irq_info omap3xxx_usb_host_hs_irqs[] = {
 	{ .name = "ohci-irq", .irq = 76 + OMAP_INTC_START, },
 	{ .name = "ehci-irq", .irq = 77 + OMAP_INTC_START, },
@@ -1981,8 +1977,6 @@ static struct omap_hwmod omap3xxx_usb_host_hs_hwmod = {
 			.idlest_stdby_bit = OMAP3430ES2_ST_USBHOST_STDBY_SHIFT,
 		},
 	},
-	.opt_clks	= omap3xxx_usb_host_hs_opt_clks,
-	.opt_clks_cnt	= ARRAY_SIZE(omap3xxx_usb_host_hs_opt_clks),
 
 	/*
 	 * Errata: USBHOST Configured In Smart-Idle Can Lead To a Deadlock
diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index c31baa7..865c276 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -692,10 +692,11 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 
 		if (need_logic_fck) {
 			omap->ehci_logic_fck = devm_clk_get(dev,
-							    "ehci_logic_fck");
+							    "usbhost_120m_fck");
 			if (IS_ERR(omap->ehci_logic_fck)) {
 				ret = PTR_ERR(omap->ehci_logic_fck);
-				dev_err(dev, "ehci_logic_fck failed:%d\n", ret);
+				dev_err(dev, "usbhost_120m_fck failed:%d\n",
+					ret);
 				goto err_mem;
 			}
 		}
-- 
1.8.3.2

[PATCH v9 4/9] mfd: omap-usb-host: Use clock names as per function for reference clocks

[Roger Quadros]

Use a meaningful name for the reference clocks so that it indicates the function.

Update the OMAP4+ USB Host node as well to be in sync with the changes.

CC: Benoît Cousson <bcousson@baylibre.com>
CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 arch/arm/boot/dts/omap4.dtsi |  6 ++++++
 arch/arm/boot/dts/omap5.dtsi |  6 ++++++
 drivers/mfd/omap-usb-host.c  | 12 ++++++------
 3 files changed, 18 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index d3f8a6e..39a05ce 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -697,6 +697,12 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
+			clocks = <&init_60m_fclk>,
+				 <&xclk60mhsp1_ck>,
+				 <&xclk60mhsp2_ck>;
+			clock-names = "refclk_60m_int",
+				      "refclk_60m_ext_p1",
+				      "refclk_60m_ext_p2";
 
 			usbhsohci: ohci@4a064800 {
 				compatible = "ti,ohci-omap3", "usb-ohci";
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index a72813a..d4dae48 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -775,6 +775,12 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
+			clocks = <&l3init_60m_fclk>,
+				 <&xclk60mhsp1_ck>,
+				 <&xclk60mhsp2_ck>;
+			clock-names = "refclk_60m_int",
+				      "refclk_60m_ext_p1",
+				      "refclk_60m_ext_p2";
 
 			usbhsohci: ohci@4a064800 {
 				compatible = "ti,ohci-omap3", "usb-ohci";
diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index 865c276..651e249 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -718,24 +718,24 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 		goto err_mem;
 	}
 
-	omap->xclk60mhsp1_ck = devm_clk_get(dev, "xclk60mhsp1_ck");
+	omap->xclk60mhsp1_ck = devm_clk_get(dev, "refclk_60m_ext_p1");
 	if (IS_ERR(omap->xclk60mhsp1_ck)) {
 		ret = PTR_ERR(omap->xclk60mhsp1_ck);
-		dev_err(dev, "xclk60mhsp1_ck failed error:%d\n", ret);
+		dev_err(dev, "refclk_60m_ext_p1 failed error:%d\n", ret);
 		goto err_mem;
 	}
 
-	omap->xclk60mhsp2_ck = devm_clk_get(dev, "xclk60mhsp2_ck");
+	omap->xclk60mhsp2_ck = devm_clk_get(dev, "refclk_60m_ext_p2");
 	if (IS_ERR(omap->xclk60mhsp2_ck)) {
 		ret = PTR_ERR(omap->xclk60mhsp2_ck);
-		dev_err(dev, "xclk60mhsp2_ck failed error:%d\n", ret);
+		dev_err(dev, "refclk_60m_ext_p2 failed error:%d\n", ret);
 		goto err_mem;
 	}
 
-	omap->init_60m_fclk = devm_clk_get(dev, "init_60m_fclk");
+	omap->init_60m_fclk = devm_clk_get(dev, "refclk_60m_int");
 	if (IS_ERR(omap->init_60m_fclk)) {
 		ret = PTR_ERR(omap->init_60m_fclk);
-		dev_err(dev, "init_60m_fclk failed error:%d\n", ret);
+		dev_err(dev, "refclk_60m_int failed error:%d\n", ret);
 		goto err_mem;
 	}
 
-- 
1.8.3.2

[PATCH v9 4/9] mfd: omap-usb-host: Use clock names as per function for reference clocks

[Roger Quadros]

Use a meaningful name for the reference clocks so that it indicates the function.

Update the OMAP4+ USB Host node as well to be in sync with the changes.

CC: Benoît Cousson <bcousson@baylibre.com>
CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 arch/arm/boot/dts/omap4.dtsi |  6 ++++++
 arch/arm/boot/dts/omap5.dtsi |  6 ++++++
 drivers/mfd/omap-usb-host.c  | 12 ++++++------
 3 files changed, 18 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index d3f8a6e..39a05ce 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -697,6 +697,12 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
+			clocks = <&init_60m_fclk>,
+				 <&xclk60mhsp1_ck>,
+				 <&xclk60mhsp2_ck>;
+			clock-names = "refclk_60m_int",
+				      "refclk_60m_ext_p1",
+				      "refclk_60m_ext_p2";
 
 			usbhsohci: ohci@4a064800 {
 				compatible = "ti,ohci-omap3", "usb-ohci";
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index a72813a..d4dae48 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -775,6 +775,12 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
+			clocks = <&l3init_60m_fclk>,
+				 <&xclk60mhsp1_ck>,
+				 <&xclk60mhsp2_ck>;
+			clock-names = "refclk_60m_int",
+				      "refclk_60m_ext_p1",
+				      "refclk_60m_ext_p2";
 
 			usbhsohci: ohci@4a064800 {
 				compatible = "ti,ohci-omap3", "usb-ohci";
diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index 865c276..651e249 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -718,24 +718,24 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 		goto err_mem;
 	}
 
-	omap->xclk60mhsp1_ck = devm_clk_get(dev, "xclk60mhsp1_ck");
+	omap->xclk60mhsp1_ck = devm_clk_get(dev, "refclk_60m_ext_p1");
 	if (IS_ERR(omap->xclk60mhsp1_ck)) {
 		ret = PTR_ERR(omap->xclk60mhsp1_ck);
-		dev_err(dev, "xclk60mhsp1_ck failed error:%d\n", ret);
+		dev_err(dev, "refclk_60m_ext_p1 failed error:%d\n", ret);
 		goto err_mem;
 	}
 
-	omap->xclk60mhsp2_ck = devm_clk_get(dev, "xclk60mhsp2_ck");
+	omap->xclk60mhsp2_ck = devm_clk_get(dev, "refclk_60m_ext_p2");
 	if (IS_ERR(omap->xclk60mhsp2_ck)) {
 		ret = PTR_ERR(omap->xclk60mhsp2_ck);
-		dev_err(dev, "xclk60mhsp2_ck failed error:%d\n", ret);
+		dev_err(dev, "refclk_60m_ext_p2 failed error:%d\n", ret);
 		goto err_mem;
 	}
 
-	omap->init_60m_fclk = devm_clk_get(dev, "init_60m_fclk");
+	omap->init_60m_fclk = devm_clk_get(dev, "refclk_60m_int");
 	if (IS_ERR(omap->init_60m_fclk)) {
 		ret = PTR_ERR(omap->init_60m_fclk);
-		dev_err(dev, "init_60m_fclk failed error:%d\n", ret);
+		dev_err(dev, "refclk_60m_int failed error:%d\n", ret);
 		goto err_mem;
 	}
 
-- 
1.8.3.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v9 4/9] mfd: omap-usb-host: Use clock names as per function for reference clocks

[Roger Quadros]

Use a meaningful name for the reference clocks so that it indicates the function.

Update the OMAP4+ USB Host node as well to be in sync with the changes.

CC: Beno?t Cousson <bcousson@baylibre.com>
CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 arch/arm/boot/dts/omap4.dtsi |  6 ++++++
 arch/arm/boot/dts/omap5.dtsi |  6 ++++++
 drivers/mfd/omap-usb-host.c  | 12 ++++++------
 3 files changed, 18 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index d3f8a6e..39a05ce 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -697,6 +697,12 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
+			clocks = <&init_60m_fclk>,
+				 <&xclk60mhsp1_ck>,
+				 <&xclk60mhsp2_ck>;
+			clock-names = "refclk_60m_int",
+				      "refclk_60m_ext_p1",
+				      "refclk_60m_ext_p2";
 
 			usbhsohci: ohci at 4a064800 {
 				compatible = "ti,ohci-omap3", "usb-ohci";
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index a72813a..d4dae48 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -775,6 +775,12 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
+			clocks = <&l3init_60m_fclk>,
+				 <&xclk60mhsp1_ck>,
+				 <&xclk60mhsp2_ck>;
+			clock-names = "refclk_60m_int",
+				      "refclk_60m_ext_p1",
+				      "refclk_60m_ext_p2";
 
 			usbhsohci: ohci at 4a064800 {
 				compatible = "ti,ohci-omap3", "usb-ohci";
diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index 865c276..651e249 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -718,24 +718,24 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 		goto err_mem;
 	}
 
-	omap->xclk60mhsp1_ck = devm_clk_get(dev, "xclk60mhsp1_ck");
+	omap->xclk60mhsp1_ck = devm_clk_get(dev, "refclk_60m_ext_p1");
 	if (IS_ERR(omap->xclk60mhsp1_ck)) {
 		ret = PTR_ERR(omap->xclk60mhsp1_ck);
-		dev_err(dev, "xclk60mhsp1_ck failed error:%d\n", ret);
+		dev_err(dev, "refclk_60m_ext_p1 failed error:%d\n", ret);
 		goto err_mem;
 	}
 
-	omap->xclk60mhsp2_ck = devm_clk_get(dev, "xclk60mhsp2_ck");
+	omap->xclk60mhsp2_ck = devm_clk_get(dev, "refclk_60m_ext_p2");
 	if (IS_ERR(omap->xclk60mhsp2_ck)) {
 		ret = PTR_ERR(omap->xclk60mhsp2_ck);
-		dev_err(dev, "xclk60mhsp2_ck failed error:%d\n", ret);
+		dev_err(dev, "refclk_60m_ext_p2 failed error:%d\n", ret);
 		goto err_mem;
 	}
 
-	omap->init_60m_fclk = devm_clk_get(dev, "init_60m_fclk");
+	omap->init_60m_fclk = devm_clk_get(dev, "refclk_60m_int");
 	if (IS_ERR(omap->init_60m_fclk)) {
 		ret = PTR_ERR(omap->init_60m_fclk);
-		dev_err(dev, "init_60m_fclk failed error:%d\n", ret);
+		dev_err(dev, "refclk_60m_int failed error:%d\n", ret);
 		goto err_mem;
 	}
 
-- 
1.8.3.2

[PATCH v9 5/9] mfd: omap-usb-host: Update DT clock binding information

[Roger Quadros]

The omap-usb-host driver expects certained named clocks.
Add this information to the DT binding document.

CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 .../devicetree/bindings/mfd/omap-usb-host.txt      | 23 ++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt
index b381fa6..4721b2d 100644
--- a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt
+++ b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt
@@ -32,6 +32,29 @@ Optional properties:
 - single-ulpi-bypass: Must be present if the controller contains a single
   ULPI bypass control bit. e.g. OMAP3 silicon <= ES2.1
 
+- clocks: a list of phandles and clock-specifier pairs, one for each entry in
+  clock-names.
+
+- clock-names: should include:
+  For OMAP3
+  * "usbhost_120m_fck" - 120MHz Functional clock.
+
+  For OMAP4+
+  * "refclk_60m_int" - 60MHz internal reference clock for UTMI clock mux
+  * "refclk_60m_ext_p1" - 60MHz external ref. clock for Port 1's UTMI clock mux.
+  * "refclk_60m_ext_p2" - 60MHz external ref. clock for Port 2's UTMI clock mux
+  * "utmi_p1_gfclk" - Port 1 UTMI clock mux.
+  * "utmi_p2_gfclk" - Port 2 UTMI clock mux.
+  * "usb_host_hs_utmi_p1_clk" - Port 1 UTMI clock gate.
+  * "usb_host_hs_utmi_p2_clk" - Port 2 UTMI clock gate.
+  * "usb_host_hs_utmi_p3_clk" - Port 3 UTMI clock gate.
+  * "usb_host_hs_hsic480m_p1_clk" - Port 1 480MHz HSIC clock gate.
+  * "usb_host_hs_hsic480m_p2_clk" - Port 2 480MHz HSIC clock gate.
+  * "usb_host_hs_hsic480m_p3_clk" - Port 3 480MHz HSIC clock gate.
+  * "usb_host_hs_hsic60m_p1_clk" - Port 1 60MHz HSIC clock gate.
+  * "usb_host_hs_hsic60m_p2_clk" - Port 2 60MHz HSIC clock gate.
+  * "usb_host_hs_hsic60m_p3_clk" - Port 3 60MHz HSIC clock gate.
+
 Required properties if child node exists:
 
 - #address-cells: Must be 1
-- 
1.8.3.2

[PATCH v9 5/9] mfd: omap-usb-host: Update DT clock binding information

[Roger Quadros]

The omap-usb-host driver expects certained named clocks.
Add this information to the DT binding document.

CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 .../devicetree/bindings/mfd/omap-usb-host.txt      | 23 ++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt
index b381fa6..4721b2d 100644
--- a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt
+++ b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt
@@ -32,6 +32,29 @@ Optional properties:
 - single-ulpi-bypass: Must be present if the controller contains a single
   ULPI bypass control bit. e.g. OMAP3 silicon <= ES2.1
 
+- clocks: a list of phandles and clock-specifier pairs, one for each entry in
+  clock-names.
+
+- clock-names: should include:
+  For OMAP3
+  * "usbhost_120m_fck" - 120MHz Functional clock.
+
+  For OMAP4+
+  * "refclk_60m_int" - 60MHz internal reference clock for UTMI clock mux
+  * "refclk_60m_ext_p1" - 60MHz external ref. clock for Port 1's UTMI clock mux.
+  * "refclk_60m_ext_p2" - 60MHz external ref. clock for Port 2's UTMI clock mux
+  * "utmi_p1_gfclk" - Port 1 UTMI clock mux.
+  * "utmi_p2_gfclk" - Port 2 UTMI clock mux.
+  * "usb_host_hs_utmi_p1_clk" - Port 1 UTMI clock gate.
+  * "usb_host_hs_utmi_p2_clk" - Port 2 UTMI clock gate.
+  * "usb_host_hs_utmi_p3_clk" - Port 3 UTMI clock gate.
+  * "usb_host_hs_hsic480m_p1_clk" - Port 1 480MHz HSIC clock gate.
+  * "usb_host_hs_hsic480m_p2_clk" - Port 2 480MHz HSIC clock gate.
+  * "usb_host_hs_hsic480m_p3_clk" - Port 3 480MHz HSIC clock gate.
+  * "usb_host_hs_hsic60m_p1_clk" - Port 1 60MHz HSIC clock gate.
+  * "usb_host_hs_hsic60m_p2_clk" - Port 2 60MHz HSIC clock gate.
+  * "usb_host_hs_hsic60m_p3_clk" - Port 3 60MHz HSIC clock gate.
+
 Required properties if child node exists:
 
 - #address-cells: Must be 1
-- 
1.8.3.2

[PATCH v9 5/9] mfd: omap-usb-host: Update DT clock binding information

[Roger Quadros]

The omap-usb-host driver expects certained named clocks.
Add this information to the DT binding document.

CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 .../devicetree/bindings/mfd/omap-usb-host.txt      | 23 ++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt
index b381fa6..4721b2d 100644
--- a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt
+++ b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt
@@ -32,6 +32,29 @@ Optional properties:
 - single-ulpi-bypass: Must be present if the controller contains a single
   ULPI bypass control bit. e.g. OMAP3 silicon <= ES2.1
 
+- clocks: a list of phandles and clock-specifier pairs, one for each entry in
+  clock-names.
+
+- clock-names: should include:
+  For OMAP3
+  * "usbhost_120m_fck" - 120MHz Functional clock.
+
+  For OMAP4+
+  * "refclk_60m_int" - 60MHz internal reference clock for UTMI clock mux
+  * "refclk_60m_ext_p1" - 60MHz external ref. clock for Port 1's UTMI clock mux.
+  * "refclk_60m_ext_p2" - 60MHz external ref. clock for Port 2's UTMI clock mux
+  * "utmi_p1_gfclk" - Port 1 UTMI clock mux.
+  * "utmi_p2_gfclk" - Port 2 UTMI clock mux.
+  * "usb_host_hs_utmi_p1_clk" - Port 1 UTMI clock gate.
+  * "usb_host_hs_utmi_p2_clk" - Port 2 UTMI clock gate.
+  * "usb_host_hs_utmi_p3_clk" - Port 3 UTMI clock gate.
+  * "usb_host_hs_hsic480m_p1_clk" - Port 1 480MHz HSIC clock gate.
+  * "usb_host_hs_hsic480m_p2_clk" - Port 2 480MHz HSIC clock gate.
+  * "usb_host_hs_hsic480m_p3_clk" - Port 3 480MHz HSIC clock gate.
+  * "usb_host_hs_hsic60m_p1_clk" - Port 1 60MHz HSIC clock gate.
+  * "usb_host_hs_hsic60m_p2_clk" - Port 2 60MHz HSIC clock gate.
+  * "usb_host_hs_hsic60m_p3_clk" - Port 3 60MHz HSIC clock gate.
+
 Required properties if child node exists:
 
 - #address-cells: Must be 1
-- 
1.8.3.2

[PATCH v9 6/9] mfd: omap-usb-tll: Update DT clock binding information

[Roger Quadros]

The omap-usb-tll driver needs one clock for each TLL channel.
Add this information to the DT binding document.

CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 Documentation/devicetree/bindings/mfd/omap-usb-tll.txt | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt
index 62fe697..c58d704 100644
--- a/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt
+++ b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt
@@ -7,6 +7,16 @@ Required properties:
 - interrupts : should contain the TLL module's interrupt
 - ti,hwmod : must contain "usb_tll_hs"
 
+Optional properties:
+
+- clocks: a list of phandles and clock-specifier pairs, one for each entry in
+  clock-names.
+
+- clock-names: should include:
+  * "usb_tll_hs_usb_ch0_clk" - USB TLL channel 0 clock
+  * "usb_tll_hs_usb_ch1_clk" - USB TLL channel 1 clock
+  * "usb_tll_hs_usb_ch2_clk" - USB TLL channel 2 clock
+
 Example:
 
 	usbhstll: usbhstll@4a062000 {
-- 
1.8.3.2

[PATCH v9 6/9] mfd: omap-usb-tll: Update DT clock binding information

[Roger Quadros]

The omap-usb-tll driver needs one clock for each TLL channel.
Add this information to the DT binding document.

CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 Documentation/devicetree/bindings/mfd/omap-usb-tll.txt | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt
index 62fe697..c58d704 100644
--- a/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt
+++ b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt
@@ -7,6 +7,16 @@ Required properties:
 - interrupts : should contain the TLL module's interrupt
 - ti,hwmod : must contain "usb_tll_hs"
 
+Optional properties:
+
+- clocks: a list of phandles and clock-specifier pairs, one for each entry in
+  clock-names.
+
+- clock-names: should include:
+  * "usb_tll_hs_usb_ch0_clk" - USB TLL channel 0 clock
+  * "usb_tll_hs_usb_ch1_clk" - USB TLL channel 1 clock
+  * "usb_tll_hs_usb_ch2_clk" - USB TLL channel 2 clock
+
 Example:
 
 	usbhstll: usbhstll@4a062000 {
-- 
1.8.3.2

[PATCH v9 6/9] mfd: omap-usb-tll: Update DT clock binding information

[Roger Quadros]

The omap-usb-tll driver needs one clock for each TLL channel.
Add this information to the DT binding document.

CC: Lee Jones <lee.jones@linaro.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 Documentation/devicetree/bindings/mfd/omap-usb-tll.txt | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt
index 62fe697..c58d704 100644
--- a/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt
+++ b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt
@@ -7,6 +7,16 @@ Required properties:
 - interrupts : should contain the TLL module's interrupt
 - ti,hwmod : must contain "usb_tll_hs"
 
+Optional properties:
+
+- clocks: a list of phandles and clock-specifier pairs, one for each entry in
+  clock-names.
+
+- clock-names: should include:
+  * "usb_tll_hs_usb_ch0_clk" - USB TLL channel 0 clock
+  * "usb_tll_hs_usb_ch1_clk" - USB TLL channel 1 clock
+  * "usb_tll_hs_usb_ch2_clk" - USB TLL channel 2 clock
+
 Example:
 
 	usbhstll: usbhstll at 4a062000 {
-- 
1.8.3.2

[PATCH v9 7/9] ARM: OMAP2+: Remove legacy_init_ehci_clk()

[Roger Quadros]

The necessary clock phandle for the EHCI clock is now provided
via device tree so we no longer need this legacy method.

Update the omap4-panda and omap5-uevm board DTS to provide the
necessary EHCI PHY clock information.

Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 arch/arm/boot/dts/omap4-panda-common.dtsi |  8 ++------
 arch/arm/boot/dts/omap5-uevm.dts          |  8 ++------
 arch/arm/mach-omap2/pdata-quirks.c        | 16 ----------------
 3 files changed, 4 insertions(+), 28 deletions(-)

diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
index 88c6a05..50b72966 100644
--- a/arch/arm/boot/dts/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
@@ -83,12 +83,8 @@
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;   /* gpio_62 */
 		vcc-supply = <&hsusb1_power>;
-	/**
-	 * FIXME:
-	 * put the right clock phandle here when available
-	 *	clocks = <&auxclk3>;
-	 *	clock-names = "main_clk";
-	 */
+		clocks = <&auxclk3_ck>;
+		clock-names = "main_clk";
 		clock-frequency = <19200000>;
 	};
 
diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts
index 002fa70..3b99ec2 100644
--- a/arch/arm/boot/dts/omap5-uevm.dts
+++ b/arch/arm/boot/dts/omap5-uevm.dts
@@ -31,12 +31,8 @@
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
-	/**
-	  * FIXME
-	  * Put the right clock phandle here when available
-	  *	clocks = <&auxclk1>;
-	  *	clock-names = "main_clk";
-	  */
+		clocks = <&auxclk1_ck>;
+		clock-names = "main_clk";
 		clock-frequency = <19200000>;
 	};
 
diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
index 3d5b24d..f1ecd86 100644
--- a/arch/arm/mach-omap2/pdata-quirks.c
+++ b/arch/arm/mach-omap2/pdata-quirks.c
@@ -31,20 +31,6 @@ struct pdata_init {
 struct of_dev_auxdata omap_auxdata_lookup[];
 static struct twl4030_gpio_platform_data twl_gpio_auxdata;
 
-/*
- * Create alias for USB host PHY clock.
- * Remove this when clock phandle can be provided via DT
- */
-static void __init __used legacy_init_ehci_clk(char *clkname)
-{
-	int ret;
-
-	ret = clk_add_alias("main_clk", NULL, clkname, NULL);
-	if (ret)
-		pr_err("%s:Failed to add main_clk alias to %s :%d\n",
-		       __func__, clkname, ret);
-}
-
 #if IS_ENABLED(CONFIG_WL12XX)
 
 static struct wl12xx_platform_data wl12xx __initdata;
@@ -182,7 +168,6 @@ static void __init omap4_sdp_legacy_init(void)
 static void __init omap4_panda_legacy_init(void)
 {
 	omap4_panda_display_init_of();
-	legacy_init_ehci_clk("auxclk3_ck");
 	legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 53);
 }
 #endif
@@ -190,7 +175,6 @@ static void __init omap4_panda_legacy_init(void)
 #ifdef CONFIG_SOC_OMAP5
 static void __init omap5_uevm_legacy_init(void)
 {
-	legacy_init_ehci_clk("auxclk1_ck");
 }
 #endif
 
-- 
1.8.3.2

[PATCH v9 7/9] ARM: OMAP2+: Remove legacy_init_ehci_clk()

[Roger Quadros]

The necessary clock phandle for the EHCI clock is now provided
via device tree so we no longer need this legacy method.

Update the omap4-panda and omap5-uevm board DTS to provide the
necessary EHCI PHY clock information.

Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 arch/arm/boot/dts/omap4-panda-common.dtsi |  8 ++------
 arch/arm/boot/dts/omap5-uevm.dts          |  8 ++------
 arch/arm/mach-omap2/pdata-quirks.c        | 16 ----------------
 3 files changed, 4 insertions(+), 28 deletions(-)

diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
index 88c6a05..50b72966 100644
--- a/arch/arm/boot/dts/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
@@ -83,12 +83,8 @@
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;   /* gpio_62 */
 		vcc-supply = <&hsusb1_power>;
-	/**
-	 * FIXME:
-	 * put the right clock phandle here when available
-	 *	clocks = <&auxclk3>;
-	 *	clock-names = "main_clk";
-	 */
+		clocks = <&auxclk3_ck>;
+		clock-names = "main_clk";
 		clock-frequency = <19200000>;
 	};
 
diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts
index 002fa70..3b99ec2 100644
--- a/arch/arm/boot/dts/omap5-uevm.dts
+++ b/arch/arm/boot/dts/omap5-uevm.dts
@@ -31,12 +31,8 @@
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
-	/**
-	  * FIXME
-	  * Put the right clock phandle here when available
-	  *	clocks = <&auxclk1>;
-	  *	clock-names = "main_clk";
-	  */
+		clocks = <&auxclk1_ck>;
+		clock-names = "main_clk";
 		clock-frequency = <19200000>;
 	};
 
diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
index 3d5b24d..f1ecd86 100644
--- a/arch/arm/mach-omap2/pdata-quirks.c
+++ b/arch/arm/mach-omap2/pdata-quirks.c
@@ -31,20 +31,6 @@ struct pdata_init {
 struct of_dev_auxdata omap_auxdata_lookup[];
 static struct twl4030_gpio_platform_data twl_gpio_auxdata;
 
-/*
- * Create alias for USB host PHY clock.
- * Remove this when clock phandle can be provided via DT
- */
-static void __init __used legacy_init_ehci_clk(char *clkname)
-{
-	int ret;
-
-	ret = clk_add_alias("main_clk", NULL, clkname, NULL);
-	if (ret)
-		pr_err("%s:Failed to add main_clk alias to %s :%d\n",
-		       __func__, clkname, ret);
-}
-
 #if IS_ENABLED(CONFIG_WL12XX)
 
 static struct wl12xx_platform_data wl12xx __initdata;
@@ -182,7 +168,6 @@ static void __init omap4_sdp_legacy_init(void)
 static void __init omap4_panda_legacy_init(void)
 {
 	omap4_panda_display_init_of();
-	legacy_init_ehci_clk("auxclk3_ck");
 	legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 53);
 }
 #endif
@@ -190,7 +175,6 @@ static void __init omap4_panda_legacy_init(void)
 #ifdef CONFIG_SOC_OMAP5
 static void __init omap5_uevm_legacy_init(void)
 {
-	legacy_init_ehci_clk("auxclk1_ck");
 }
 #endif
 
-- 
1.8.3.2

[PATCH v9 7/9] ARM: OMAP2+: Remove legacy_init_ehci_clk()

[Roger Quadros]

The necessary clock phandle for the EHCI clock is now provided
via device tree so we no longer need this legacy method.

Update the omap4-panda and omap5-uevm board DTS to provide the
necessary EHCI PHY clock information.

Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 arch/arm/boot/dts/omap4-panda-common.dtsi |  8 ++------
 arch/arm/boot/dts/omap5-uevm.dts          |  8 ++------
 arch/arm/mach-omap2/pdata-quirks.c        | 16 ----------------
 3 files changed, 4 insertions(+), 28 deletions(-)

diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
index 88c6a05..50b72966 100644
--- a/arch/arm/boot/dts/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
@@ -83,12 +83,8 @@
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;   /* gpio_62 */
 		vcc-supply = <&hsusb1_power>;
-	/**
-	 * FIXME:
-	 * put the right clock phandle here when available
-	 *	clocks = <&auxclk3>;
-	 *	clock-names = "main_clk";
-	 */
+		clocks = <&auxclk3_ck>;
+		clock-names = "main_clk";
 		clock-frequency = <19200000>;
 	};
 
diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts
index 002fa70..3b99ec2 100644
--- a/arch/arm/boot/dts/omap5-uevm.dts
+++ b/arch/arm/boot/dts/omap5-uevm.dts
@@ -31,12 +31,8 @@
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
-	/**
-	  * FIXME
-	  * Put the right clock phandle here when available
-	  *	clocks = <&auxclk1>;
-	  *	clock-names = "main_clk";
-	  */
+		clocks = <&auxclk1_ck>;
+		clock-names = "main_clk";
 		clock-frequency = <19200000>;
 	};
 
diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
index 3d5b24d..f1ecd86 100644
--- a/arch/arm/mach-omap2/pdata-quirks.c
+++ b/arch/arm/mach-omap2/pdata-quirks.c
@@ -31,20 +31,6 @@ struct pdata_init {
 struct of_dev_auxdata omap_auxdata_lookup[];
 static struct twl4030_gpio_platform_data twl_gpio_auxdata;
 
-/*
- * Create alias for USB host PHY clock.
- * Remove this when clock phandle can be provided via DT
- */
-static void __init __used legacy_init_ehci_clk(char *clkname)
-{
-	int ret;
-
-	ret = clk_add_alias("main_clk", NULL, clkname, NULL);
-	if (ret)
-		pr_err("%s:Failed to add main_clk alias to %s :%d\n",
-		       __func__, clkname, ret);
-}
-
 #if IS_ENABLED(CONFIG_WL12XX)
 
 static struct wl12xx_platform_data wl12xx __initdata;
@@ -182,7 +168,6 @@ static void __init omap4_sdp_legacy_init(void)
 static void __init omap4_panda_legacy_init(void)
 {
 	omap4_panda_display_init_of();
-	legacy_init_ehci_clk("auxclk3_ck");
 	legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 53);
 }
 #endif
@@ -190,7 +175,6 @@ static void __init omap4_panda_legacy_init(void)
 #ifdef CONFIG_SOC_OMAP5
 static void __init omap5_uevm_legacy_init(void)
 {
-	legacy_init_ehci_clk("auxclk1_ck");
 }
 #endif
 
-- 
1.8.3.2

[PATCH v9 8/9] ARM: dts: OMAP2+: Get rid of incompatible ids for USB host nodes

[Roger Quadros]

The OMAP EHCI and OHCI controllers are not compatible with drivers
other than "ti,ehci-omap" and "ti,ohci-omap3" respectively, so get
rid of the incompatible ids.

CC: Alan Stern <stern@rowland.harvard.edu>
CC: Nishant Menon <nm@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 arch/arm/boot/dts/omap3.dtsi | 4 ++--
 arch/arm/boot/dts/omap4.dtsi | 4 ++--
 arch/arm/boot/dts/omap5.dtsi | 4 ++--
 3 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index a5fc83b..8e7de9e 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -634,14 +634,14 @@
 			ranges;
 
 			usbhsohci: ohci@48064400 {
-				compatible = "ti,ohci-omap3", "usb-ohci";
+				compatible = "ti,ohci-omap3";
 				reg = <0x48064400 0x400>;
 				interrupt-parent = <&intc>;
 				interrupts = <76>;
 			};
 
 			usbhsehci: ehci@48064800 {
-				compatible = "ti,ehci-omap", "usb-ehci";
+				compatible = "ti,ehci-omap";
 				reg = <0x48064800 0x400>;
 				interrupt-parent = <&intc>;
 				interrupts = <77>;
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 39a05ce..ff1b057 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -705,14 +705,14 @@
 				      "refclk_60m_ext_p2";
 
 			usbhsohci: ohci@4a064800 {
-				compatible = "ti,ohci-omap3", "usb-ohci";
+				compatible = "ti,ohci-omap3";
 				reg = <0x4a064800 0x400>;
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			usbhsehci: ehci@4a064c00 {
-				compatible = "ti,ehci-omap", "usb-ehci";
+				compatible = "ti,ehci-omap";
 				reg = <0x4a064c00 0x400>;
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index d4dae48..f65aa65 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -783,14 +783,14 @@
 				      "refclk_60m_ext_p2";
 
 			usbhsohci: ohci@4a064800 {
-				compatible = "ti,ohci-omap3", "usb-ohci";
+				compatible = "ti,ohci-omap3";
 				reg = <0x4a064800 0x400>;
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			usbhsehci: ehci@4a064c00 {
-				compatible = "ti,ehci-omap", "usb-ehci";
+				compatible = "ti,ehci-omap";
 				reg = <0x4a064c00 0x400>;
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
-- 
1.8.3.2

[PATCH v9 8/9] ARM: dts: OMAP2+: Get rid of incompatible ids for USB host nodes

[Roger Quadros]

The OMAP EHCI and OHCI controllers are not compatible with drivers
other than "ti,ehci-omap" and "ti,ohci-omap3" respectively, so get
rid of the incompatible ids.

CC: Alan Stern <stern@rowland.harvard.edu>
CC: Nishant Menon <nm@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 arch/arm/boot/dts/omap3.dtsi | 4 ++--
 arch/arm/boot/dts/omap4.dtsi | 4 ++--
 arch/arm/boot/dts/omap5.dtsi | 4 ++--
 3 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index a5fc83b..8e7de9e 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -634,14 +634,14 @@
 			ranges;
 
 			usbhsohci: ohci@48064400 {
-				compatible = "ti,ohci-omap3", "usb-ohci";
+				compatible = "ti,ohci-omap3";
 				reg = <0x48064400 0x400>;
 				interrupt-parent = <&intc>;
 				interrupts = <76>;
 			};
 
 			usbhsehci: ehci@48064800 {
-				compatible = "ti,ehci-omap", "usb-ehci";
+				compatible = "ti,ehci-omap";
 				reg = <0x48064800 0x400>;
 				interrupt-parent = <&intc>;
 				interrupts = <77>;
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 39a05ce..ff1b057 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -705,14 +705,14 @@
 				      "refclk_60m_ext_p2";
 
 			usbhsohci: ohci@4a064800 {
-				compatible = "ti,ohci-omap3", "usb-ohci";
+				compatible = "ti,ohci-omap3";
 				reg = <0x4a064800 0x400>;
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			usbhsehci: ehci@4a064c00 {
-				compatible = "ti,ehci-omap", "usb-ehci";
+				compatible = "ti,ehci-omap";
 				reg = <0x4a064c00 0x400>;
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index d4dae48..f65aa65 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -783,14 +783,14 @@
 				      "refclk_60m_ext_p2";
 
 			usbhsohci: ohci@4a064800 {
-				compatible = "ti,ohci-omap3", "usb-ohci";
+				compatible = "ti,ohci-omap3";
 				reg = <0x4a064800 0x400>;
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			usbhsehci: ehci@4a064c00 {
-				compatible = "ti,ehci-omap", "usb-ehci";
+				compatible = "ti,ehci-omap";
 				reg = <0x4a064c00 0x400>;
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
-- 
1.8.3.2

[PATCH v9 8/9] ARM: dts: OMAP2+: Get rid of incompatible ids for USB host nodes

[Roger Quadros]

The OMAP EHCI and OHCI controllers are not compatible with drivers
other than "ti,ehci-omap" and "ti,ohci-omap3" respectively, so get
rid of the incompatible ids.

CC: Alan Stern <stern@rowland.harvard.edu>
CC: Nishant Menon <nm@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 arch/arm/boot/dts/omap3.dtsi | 4 ++--
 arch/arm/boot/dts/omap4.dtsi | 4 ++--
 arch/arm/boot/dts/omap5.dtsi | 4 ++--
 3 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index a5fc83b..8e7de9e 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -634,14 +634,14 @@
 			ranges;
 
 			usbhsohci: ohci at 48064400 {
-				compatible = "ti,ohci-omap3", "usb-ohci";
+				compatible = "ti,ohci-omap3";
 				reg = <0x48064400 0x400>;
 				interrupt-parent = <&intc>;
 				interrupts = <76>;
 			};
 
 			usbhsehci: ehci at 48064800 {
-				compatible = "ti,ehci-omap", "usb-ehci";
+				compatible = "ti,ehci-omap";
 				reg = <0x48064800 0x400>;
 				interrupt-parent = <&intc>;
 				interrupts = <77>;
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 39a05ce..ff1b057 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -705,14 +705,14 @@
 				      "refclk_60m_ext_p2";
 
 			usbhsohci: ohci at 4a064800 {
-				compatible = "ti,ohci-omap3", "usb-ohci";
+				compatible = "ti,ohci-omap3";
 				reg = <0x4a064800 0x400>;
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			usbhsehci: ehci at 4a064c00 {
-				compatible = "ti,ehci-omap", "usb-ehci";
+				compatible = "ti,ehci-omap";
 				reg = <0x4a064c00 0x400>;
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index d4dae48..f65aa65 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -783,14 +783,14 @@
 				      "refclk_60m_ext_p2";
 
 			usbhsohci: ohci at 4a064800 {
-				compatible = "ti,ohci-omap3", "usb-ohci";
+				compatible = "ti,ohci-omap3";
 				reg = <0x4a064800 0x400>;
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			usbhsehci: ehci at 4a064c00 {
-				compatible = "ti,ehci-omap", "usb-ehci";
+				compatible = "ti,ehci-omap";
 				reg = <0x4a064c00 0x400>;
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
-- 
1.8.3.2

[PATCH v9 9/9] usb: omap: dts: Update DT binding example usage

[Roger Quadros]

Remove non-compatible id from examples.

CC: Alan Stern <stern@rowland.harvard.edu>
CC: Nishant Menon <nm@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 Documentation/devicetree/bindings/usb/ehci-omap.txt  | 2 +-
 Documentation/devicetree/bindings/usb/ohci-omap3.txt | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/usb/ehci-omap.txt b/Documentation/devicetree/bindings/usb/ehci-omap.txt
index 485a9a1..3dc231c 100644
--- a/Documentation/devicetree/bindings/usb/ehci-omap.txt
+++ b/Documentation/devicetree/bindings/usb/ehci-omap.txt
@@ -21,7 +21,7 @@ Documentation/devicetree/bindings/mfd/omap-usb-host.txt
 Example for OMAP4:
 
 usbhsehci: ehci@4a064c00 {
-	compatible = "ti,ehci-omap", "usb-ehci";
+	compatible = "ti,ehci-omap";
 	reg = <0x4a064c00 0x400>;
 	interrupts = <0 77 0x4>;
 };
diff --git a/Documentation/devicetree/bindings/usb/ohci-omap3.txt b/Documentation/devicetree/bindings/usb/ohci-omap3.txt
index 14ab428..ce8c47cff 100644
--- a/Documentation/devicetree/bindings/usb/ohci-omap3.txt
+++ b/Documentation/devicetree/bindings/usb/ohci-omap3.txt
@@ -9,7 +9,7 @@ Required properties:
 Example for OMAP4:
 
 usbhsohci: ohci@4a064800 {
-	compatible = "ti,ohci-omap3", "usb-ohci";
+	compatible = "ti,ohci-omap3";
 	reg = <0x4a064800 0x400>;
 	interrupts = <0 76 0x4>;
 };
-- 
1.8.3.2

[PATCH v9 9/9] usb: omap: dts: Update DT binding example usage

[Roger Quadros]

Remove non-compatible id from examples.

CC: Alan Stern <stern@rowland.harvard.edu>
CC: Nishant Menon <nm@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 Documentation/devicetree/bindings/usb/ehci-omap.txt  | 2 +-
 Documentation/devicetree/bindings/usb/ohci-omap3.txt | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/usb/ehci-omap.txt b/Documentation/devicetree/bindings/usb/ehci-omap.txt
index 485a9a1..3dc231c 100644
--- a/Documentation/devicetree/bindings/usb/ehci-omap.txt
+++ b/Documentation/devicetree/bindings/usb/ehci-omap.txt
@@ -21,7 +21,7 @@ Documentation/devicetree/bindings/mfd/omap-usb-host.txt
 Example for OMAP4:
 
 usbhsehci: ehci@4a064c00 {
-	compatible = "ti,ehci-omap", "usb-ehci";
+	compatible = "ti,ehci-omap";
 	reg = <0x4a064c00 0x400>;
 	interrupts = <0 77 0x4>;
 };
diff --git a/Documentation/devicetree/bindings/usb/ohci-omap3.txt b/Documentation/devicetree/bindings/usb/ohci-omap3.txt
index 14ab428..ce8c47cff 100644
--- a/Documentation/devicetree/bindings/usb/ohci-omap3.txt
+++ b/Documentation/devicetree/bindings/usb/ohci-omap3.txt
@@ -9,7 +9,7 @@ Required properties:
 Example for OMAP4:
 
 usbhsohci: ohci@4a064800 {
-	compatible = "ti,ohci-omap3", "usb-ohci";
+	compatible = "ti,ohci-omap3";
 	reg = <0x4a064800 0x400>;
 	interrupts = <0 76 0x4>;
 };
-- 
1.8.3.2

[PATCH v9 9/9] usb: omap: dts: Update DT binding example usage

[Roger Quadros]

Remove non-compatible id from examples.

CC: Alan Stern <stern@rowland.harvard.edu>
CC: Nishant Menon <nm@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 Documentation/devicetree/bindings/usb/ehci-omap.txt  | 2 +-
 Documentation/devicetree/bindings/usb/ohci-omap3.txt | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/usb/ehci-omap.txt b/Documentation/devicetree/bindings/usb/ehci-omap.txt
index 485a9a1..3dc231c 100644
--- a/Documentation/devicetree/bindings/usb/ehci-omap.txt
+++ b/Documentation/devicetree/bindings/usb/ehci-omap.txt
@@ -21,7 +21,7 @@ Documentation/devicetree/bindings/mfd/omap-usb-host.txt
 Example for OMAP4:
 
 usbhsehci: ehci at 4a064c00 {
-	compatible = "ti,ehci-omap", "usb-ehci";
+	compatible = "ti,ehci-omap";
 	reg = <0x4a064c00 0x400>;
 	interrupts = <0 77 0x4>;
 };
diff --git a/Documentation/devicetree/bindings/usb/ohci-omap3.txt b/Documentation/devicetree/bindings/usb/ohci-omap3.txt
index 14ab428..ce8c47cff 100644
--- a/Documentation/devicetree/bindings/usb/ohci-omap3.txt
+++ b/Documentation/devicetree/bindings/usb/ohci-omap3.txt
@@ -9,7 +9,7 @@ Required properties:
 Example for OMAP4:
 
 usbhsohci: ohci at 4a064800 {
-	compatible = "ti,ohci-omap3", "usb-ohci";
+	compatible = "ti,ohci-omap3";
 	reg = <0x4a064800 0x400>;
 	interrupts = <0 76 0x4>;
 };
-- 
1.8.3.2

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Tony Lindgren]

* Roger Quadros <rogerq@ti.com> [140227 06:21]:
> Hi,
> 
> This patchset brings up USB Host ports and Ethernet port on
> the OMAP5 uEVM board.
> 
> It also does some cleanup with respect to DT clock binding
> for the mfd/omap-usb-host driver.
> 
> Please queue these for -next.
> 
> Lee,
> 
> I've folded some platform data dependent patches with mfd patches
> so that they don't break functionality when applied individually.
> You can safely pull in all MFD patches (1 to 6).
> 
> Tony & Benoit,
> 
> Can you please accept patches 7, 8 and 9?

Are 7, 8 and 9 safe to queue separately from the MFD changes
or do they need to wait for the MFD changes to get merged
first?

Regards,

Tony

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Tony Lindgren]

* Roger Quadros <rogerq-l0cyMroinI0@public.gmane.org> [140227 06:21]:
> Hi,
> 
> This patchset brings up USB Host ports and Ethernet port on
> the OMAP5 uEVM board.
> 
> It also does some cleanup with respect to DT clock binding
> for the mfd/omap-usb-host driver.
> 
> Please queue these for -next.
> 
> Lee,
> 
> I've folded some platform data dependent patches with mfd patches
> so that they don't break functionality when applied individually.
> You can safely pull in all MFD patches (1 to 6).
> 
> Tony & Benoit,
> 
> Can you please accept patches 7, 8 and 9?

Are 7, 8 and 9 safe to queue separately from the MFD changes
or do they need to wait for the MFD changes to get merged
first?

Regards,

Tony
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Tony Lindgren]

* Roger Quadros <rogerq@ti.com> [140227 06:21]:
> Hi,
> 
> This patchset brings up USB Host ports and Ethernet port on
> the OMAP5 uEVM board.
> 
> It also does some cleanup with respect to DT clock binding
> for the mfd/omap-usb-host driver.
> 
> Please queue these for -next.
> 
> Lee,
> 
> I've folded some platform data dependent patches with mfd patches
> so that they don't break functionality when applied individually.
> You can safely pull in all MFD patches (1 to 6).
> 
> Tony & Benoit,
> 
> Can you please accept patches 7, 8 and 9?

Are 7, 8 and 9 safe to queue separately from the MFD changes
or do they need to wait for the MFD changes to get merged
first?

Regards,

Tony

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Roger Quadros]

Hi Tony,

On 03/01/2014 12:56 AM, Tony Lindgren wrote:
> * Roger Quadros <rogerq@ti.com> [140227 06:21]:
>> Hi,
>>
>> This patchset brings up USB Host ports and Ethernet port on
>> the OMAP5 uEVM board.
>>
>> It also does some cleanup with respect to DT clock binding
>> for the mfd/omap-usb-host driver.
>>
>> Please queue these for -next.
>>
>> Lee,
>>
>> I've folded some platform data dependent patches with mfd patches
>> so that they don't break functionality when applied individually.
>> You can safely pull in all MFD patches (1 to 6).
>>
>> Tony & Benoit,
>>
>> Can you please accept patches 7, 8 and 9?
> 
> Are 7, 8 and 9 safe to queue separately from the MFD changes
> or do they need to wait for the MFD changes to get merged
> first?
> 

They are safe to queue separately.

cheers,
-roger

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Roger Quadros]

Hi Tony,

On 03/01/2014 12:56 AM, Tony Lindgren wrote:
> * Roger Quadros <rogerq-l0cyMroinI0@public.gmane.org> [140227 06:21]:
>> Hi,
>>
>> This patchset brings up USB Host ports and Ethernet port on
>> the OMAP5 uEVM board.
>>
>> It also does some cleanup with respect to DT clock binding
>> for the mfd/omap-usb-host driver.
>>
>> Please queue these for -next.
>>
>> Lee,
>>
>> I've folded some platform data dependent patches with mfd patches
>> so that they don't break functionality when applied individually.
>> You can safely pull in all MFD patches (1 to 6).
>>
>> Tony & Benoit,
>>
>> Can you please accept patches 7, 8 and 9?
> 
> Are 7, 8 and 9 safe to queue separately from the MFD changes
> or do they need to wait for the MFD changes to get merged
> first?
> 

They are safe to queue separately.

cheers,
-roger
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Roger Quadros]

Hi Tony,

On 03/01/2014 12:56 AM, Tony Lindgren wrote:
> * Roger Quadros <rogerq@ti.com> [140227 06:21]:
>> Hi,
>>
>> This patchset brings up USB Host ports and Ethernet port on
>> the OMAP5 uEVM board.
>>
>> It also does some cleanup with respect to DT clock binding
>> for the mfd/omap-usb-host driver.
>>
>> Please queue these for -next.
>>
>> Lee,
>>
>> I've folded some platform data dependent patches with mfd patches
>> so that they don't break functionality when applied individually.
>> You can safely pull in all MFD patches (1 to 6).
>>
>> Tony & Benoit,
>>
>> Can you please accept patches 7, 8 and 9?
> 
> Are 7, 8 and 9 safe to queue separately from the MFD changes
> or do they need to wait for the MFD changes to get merged
> first?
> 

They are safe to queue separately.

cheers,
-roger

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Tony Lindgren]

* Roger Quadros <rogerq@ti.com> [140303 01:38]:
> Hi Tony,
> 
> On 03/01/2014 12:56 AM, Tony Lindgren wrote:
> > * Roger Quadros <rogerq@ti.com> [140227 06:21]:
> >> Hi,
> >>
> >> This patchset brings up USB Host ports and Ethernet port on
> >> the OMAP5 uEVM board.
> >>
> >> It also does some cleanup with respect to DT clock binding
> >> for the mfd/omap-usb-host driver.
> >>
> >> Please queue these for -next.
> >>
> >> Lee,
> >>
> >> I've folded some platform data dependent patches with mfd patches
> >> so that they don't break functionality when applied individually.
> >> You can safely pull in all MFD patches (1 to 6).
> >>
> >> Tony & Benoit,
> >>
> >> Can you please accept patches 7, 8 and 9?
> > 
> > Are 7, 8 and 9 safe to queue separately from the MFD changes
> > or do they need to wait for the MFD changes to get merged
> > first?
> > 
> 
> They are safe to queue separately.

OK thanks applying 7, 8 and 9 into omap-for-v3.15/dt.

Regards,

Tony

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Tony Lindgren]

* Roger Quadros <rogerq-l0cyMroinI0@public.gmane.org> [140303 01:38]:
> Hi Tony,
> 
> On 03/01/2014 12:56 AM, Tony Lindgren wrote:
> > * Roger Quadros <rogerq-l0cyMroinI0@public.gmane.org> [140227 06:21]:
> >> Hi,
> >>
> >> This patchset brings up USB Host ports and Ethernet port on
> >> the OMAP5 uEVM board.
> >>
> >> It also does some cleanup with respect to DT clock binding
> >> for the mfd/omap-usb-host driver.
> >>
> >> Please queue these for -next.
> >>
> >> Lee,
> >>
> >> I've folded some platform data dependent patches with mfd patches
> >> so that they don't break functionality when applied individually.
> >> You can safely pull in all MFD patches (1 to 6).
> >>
> >> Tony & Benoit,
> >>
> >> Can you please accept patches 7, 8 and 9?
> > 
> > Are 7, 8 and 9 safe to queue separately from the MFD changes
> > or do they need to wait for the MFD changes to get merged
> > first?
> > 
> 
> They are safe to queue separately.

OK thanks applying 7, 8 and 9 into omap-for-v3.15/dt.

Regards,

Tony
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Tony Lindgren]

* Roger Quadros <rogerq@ti.com> [140303 01:38]:
> Hi Tony,
> 
> On 03/01/2014 12:56 AM, Tony Lindgren wrote:
> > * Roger Quadros <rogerq@ti.com> [140227 06:21]:
> >> Hi,
> >>
> >> This patchset brings up USB Host ports and Ethernet port on
> >> the OMAP5 uEVM board.
> >>
> >> It also does some cleanup with respect to DT clock binding
> >> for the mfd/omap-usb-host driver.
> >>
> >> Please queue these for -next.
> >>
> >> Lee,
> >>
> >> I've folded some platform data dependent patches with mfd patches
> >> so that they don't break functionality when applied individually.
> >> You can safely pull in all MFD patches (1 to 6).
> >>
> >> Tony & Benoit,
> >>
> >> Can you please accept patches 7, 8 and 9?
> > 
> > Are 7, 8 and 9 safe to queue separately from the MFD changes
> > or do they need to wait for the MFD changes to get merged
> > first?
> > 
> 
> They are safe to queue separately.

OK thanks applying 7, 8 and 9 into omap-for-v3.15/dt.

Regards,

Tony

Re: [PATCH v9 1/9] mfd: omap-usb-host: Get clocks based on hardware revision

[Lee Jones]

> Not all revisions have all the clocks so get the necessary clocks
> based on hardware revision.
> 
> This should avoid un-necessary clk_get failure messages that were
> observed earlier.
> 
> Also remove the dummy USB host clocks from the OMAP3 clock data.
> These are no longer expected by the driver.
> 
> CC: Lee Jones <lee.jones@linaro.org>
> CC: Samuel Ortiz <sameo@linux.intel.com>
> CC: Tero Kristo <t-kristo@ti.com>
> Acked-by: Mike Turquette <mturquette@linaro.org> [OMAP3 CLK data]
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
>  arch/arm/mach-omap2/cclock3xxx_data.c |  4 ----
>  drivers/clk/ti/clk-3xxx.c             |  4 ----
>  drivers/mfd/omap-usb-host.c           | 43 ++++++++++++++++++++++++++---------
>  3 files changed, 32 insertions(+), 19 deletions(-)

Patches starting to take shape. I know that I've reviewed this patch
before, so if you've fixed-up all my previous comments you can have my
Ack for the MFD changes:
  Acked-by: Lee Jones <lee.jones@linaro.org>

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v9 1/9] mfd: omap-usb-host: Get clocks based on hardware revision

[Lee Jones]

> Not all revisions have all the clocks so get the necessary clocks
> based on hardware revision.
> 
> This should avoid un-necessary clk_get failure messages that were
> observed earlier.
> 
> Also remove the dummy USB host clocks from the OMAP3 clock data.
> These are no longer expected by the driver.
> 
> CC: Lee Jones <lee.jones@linaro.org>
> CC: Samuel Ortiz <sameo@linux.intel.com>
> CC: Tero Kristo <t-kristo@ti.com>
> Acked-by: Mike Turquette <mturquette@linaro.org> [OMAP3 CLK data]
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
>  arch/arm/mach-omap2/cclock3xxx_data.c |  4 ----
>  drivers/clk/ti/clk-3xxx.c             |  4 ----
>  drivers/mfd/omap-usb-host.c           | 43 ++++++++++++++++++++++++++---------
>  3 files changed, 32 insertions(+), 19 deletions(-)

Patches starting to take shape. I know that I've reviewed this patch
before, so if you've fixed-up all my previous comments you can have my
Ack for the MFD changes:
  Acked-by: Lee Jones <lee.jones@linaro.org>

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v9 1/9] mfd: omap-usb-host: Get clocks based on hardware revision

[Lee Jones]

> Not all revisions have all the clocks so get the necessary clocks
> based on hardware revision.
> 
> This should avoid un-necessary clk_get failure messages that were
> observed earlier.
> 
> Also remove the dummy USB host clocks from the OMAP3 clock data.
> These are no longer expected by the driver.
> 
> CC: Lee Jones <lee.jones@linaro.org>
> CC: Samuel Ortiz <sameo@linux.intel.com>
> CC: Tero Kristo <t-kristo@ti.com>
> Acked-by: Mike Turquette <mturquette@linaro.org> [OMAP3 CLK data]
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
>  arch/arm/mach-omap2/cclock3xxx_data.c |  4 ----
>  drivers/clk/ti/clk-3xxx.c             |  4 ----
>  drivers/mfd/omap-usb-host.c           | 43 ++++++++++++++++++++++++++---------
>  3 files changed, 32 insertions(+), 19 deletions(-)

Patches starting to take shape. I know that I've reviewed this patch
before, so if you've fixed-up all my previous comments you can have my
Ack for the MFD changes:
  Acked-by: Lee Jones <lee.jones@linaro.org>

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v9 2/9] mfd: omap-usb-host: Always fail on clk_get() error

[Lee Jones]

> Be more strict and always fail on clk_get() error.
> 
> CC: Lee Jones <lee.jones@linaro.org>
> CC: Samuel Ortiz <sameo@linux.intel.com>
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
>  drivers/mfd/omap-usb-host.c | 62 +++++++++++++++++++++++++++++----------------
>  1 file changed, 40 insertions(+), 22 deletions(-)

I like to principle of the patch assuming that the devices would be
useless without their clocks.

Acked-by: Lee Jones <lee.jones@linaro.org>

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v9 2/9] mfd: omap-usb-host: Always fail on clk_get() error

[Lee Jones]

> Be more strict and always fail on clk_get() error.
> 
> CC: Lee Jones <lee.jones@linaro.org>
> CC: Samuel Ortiz <sameo@linux.intel.com>
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
>  drivers/mfd/omap-usb-host.c | 62 +++++++++++++++++++++++++++++----------------
>  1 file changed, 40 insertions(+), 22 deletions(-)

I like to principle of the patch assuming that the devices would be
useless without their clocks.

Acked-by: Lee Jones <lee.jones@linaro.org>

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v9 2/9] mfd: omap-usb-host: Always fail on clk_get() error

[Lee Jones]

> Be more strict and always fail on clk_get() error.
> 
> CC: Lee Jones <lee.jones@linaro.org>
> CC: Samuel Ortiz <sameo@linux.intel.com>
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
>  drivers/mfd/omap-usb-host.c | 62 +++++++++++++++++++++++++++++----------------
>  1 file changed, 40 insertions(+), 22 deletions(-)

I like to principle of the patch assuming that the devices would be
useless without their clocks.

Acked-by: Lee Jones <lee.jones@linaro.org>

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v9 3/9] mfd: omap-usb-host: Use proper clock name instead of alias

[Lee Jones]

> Use the proper clock name 'usbhost_120m_fck' instead of the
> alias 'ehci_logic_fck'
> 
> Get rid of the 'ehci_logic_fck' alias from the OMAP3 hwmod data
> as well.
> 
> CC: Paul Walmsley <paul@pwsan.com>
> CC: Lee Jones <lee.jones@linaro.org>
> CC: Samuel Ortiz <sameo@linux.intel.com>
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
>  arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 6 ------
>  drivers/mfd/omap-usb-host.c                | 5 +++--
>  2 files changed, 3 insertions(+), 8 deletions(-)

So long as the platform guys are okay with the semantic change, the
MFD diff looks okay to me. For the MFD changes:
  Acked-by: Lee Jones <lee.jones@linaro.org>

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH v9 3/9] mfd: omap-usb-host: Use proper clock name instead of alias

[Lee Jones]

> Use the proper clock name 'usbhost_120m_fck' instead of the
> alias 'ehci_logic_fck'
> 
> Get rid of the 'ehci_logic_fck' alias from the OMAP3 hwmod data
> as well.
> 
> CC: Paul Walmsley <paul@pwsan.com>
> CC: Lee Jones <lee.jones@linaro.org>
> CC: Samuel Ortiz <sameo@linux.intel.com>
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
>  arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 6 ------
>  drivers/mfd/omap-usb-host.c                | 5 +++--
>  2 files changed, 3 insertions(+), 8 deletions(-)

So long as the platform guys are okay with the semantic change, the
MFD diff looks okay to me. For the MFD changes:
  Acked-by: Lee Jones <lee.jones@linaro.org>

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v9 4/9] mfd: omap-usb-host: Use clock names as per function for reference clocks

[Lee Jones]

> Use a meaningful name for the reference clocks so that it indicates the function.
> 
> Update the OMAP4+ USB Host node as well to be in sync with the changes.
> 
> CC: Benoît Cousson <bcousson@baylibre.com>
> CC: Lee Jones <lee.jones@linaro.org>
> CC: Samuel Ortiz <sameo@linux.intel.com>
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
>  arch/arm/boot/dts/omap4.dtsi |  6 ++++++
>  arch/arm/boot/dts/omap5.dtsi |  6 ++++++
>  drivers/mfd/omap-usb-host.c  | 12 ++++++------
>  3 files changed, 18 insertions(+), 6 deletions(-)

The code looks fine and I queried the name change semantics before and
was satisfied with your answer, so as long as this patch has been
tested and nothing is broken:
  Acked-by: Lee Jones <lee.jones@linaro.org>

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v9 4/9] mfd: omap-usb-host: Use clock names as per function for reference clocks

[Lee Jones]

> Use a meaningful name for the reference clocks so that it indicates the function.
> 
> Update the OMAP4+ USB Host node as well to be in sync with the changes.
> 
> CC: Benoît Cousson <bcousson@baylibre.com>
> CC: Lee Jones <lee.jones@linaro.org>
> CC: Samuel Ortiz <sameo@linux.intel.com>
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
>  arch/arm/boot/dts/omap4.dtsi |  6 ++++++
>  arch/arm/boot/dts/omap5.dtsi |  6 ++++++
>  drivers/mfd/omap-usb-host.c  | 12 ++++++------
>  3 files changed, 18 insertions(+), 6 deletions(-)

The code looks fine and I queried the name change semantics before and
was satisfied with your answer, so as long as this patch has been
tested and nothing is broken:
  Acked-by: Lee Jones <lee.jones@linaro.org>

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v9 4/9] mfd: omap-usb-host: Use clock names as per function for reference clocks

[Lee Jones]

> Use a meaningful name for the reference clocks so that it indicates the function.
> 
> Update the OMAP4+ USB Host node as well to be in sync with the changes.
> 
> CC: Beno?t Cousson <bcousson@baylibre.com>
> CC: Lee Jones <lee.jones@linaro.org>
> CC: Samuel Ortiz <sameo@linux.intel.com>
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
>  arch/arm/boot/dts/omap4.dtsi |  6 ++++++
>  arch/arm/boot/dts/omap5.dtsi |  6 ++++++
>  drivers/mfd/omap-usb-host.c  | 12 ++++++------
>  3 files changed, 18 insertions(+), 6 deletions(-)

The code looks fine and I queried the name change semantics before and
was satisfied with your answer, so as long as this patch has been
tested and nothing is broken:
  Acked-by: Lee Jones <lee.jones@linaro.org>

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Roger Quadros]

Hi Lee,

On 02/27/2014 04:18 PM, Roger Quadros wrote:
> Hi,
> 
> This patchset brings up USB Host ports and Ethernet port on
> the OMAP5 uEVM board.
> 
> It also does some cleanup with respect to DT clock binding
> for the mfd/omap-usb-host driver.
> 
> Please queue these for -next.
> 
> Lee,
> 
> I've folded some platform data dependent patches with mfd patches
> so that they don't break functionality when applied individually.
> You can safely pull in all MFD patches (1 to 6).
> 
> Tony & Benoit,
> 
> Can you please accept patches 7, 8 and 9?

Tony has already picked up 7,8 and 9 through omap-soc tree.

Since you acked most patches except 5 and 6, are you fine if Tony takes
all the patches 1 to 4 in this series via omap-soc tree?

What about patches 5 and 6?

cheers,
-roger

> 
> Thanks.
> 
> Tested on:
>  - OMAP5 uEVM
>  - Pandaboard ES Rev. B1
>  - Beagleboard-XM Rev C2 (DT + Legacy)
>  - Beagleboard Rev C4 (DT + Legacy)
> 
> Changelog:
> 
> v9:
> - Folded dependent platform data patches into MFD patches.
> 
> v8:
> - Addressed review comments and split patch
>   "mfd: omap-usb-host: Get clocks based on hardware revision"
> - Removed unnecessary usb host dummy clocks on OMAP3
> - Removed unnecessary clock alias "ehci_logic_fck" for OMAP3
> - Rebased on 3.14-rc3
> 
> v7:
> - Rebased on 3.14-rc2
> - Removed incompatible ids from DT files and examples
> 
> v6:
> - Initialized clocks to -ENODEV and split patch 3.
> 
> v5:
> - Expose all clocks in the DT binding document for mfd:omap-usb-host
> and mfd:omap-usb-tll
> 
> v4:
> - Updated DT binding document for clock binding
> 
> v3:
> - Rebased on top of 3.13-rc7
> 
> cheers,
> -roger
> 
> ---
> Roger Quadros (9):
>   mfd: omap-usb-host: Get clocks based on hardware revision
>   mfd: omap-usb-host: Always fail on clk_get() error
>   mfd: omap-usb-host: Use proper clock name instead of alias
>   mfd: omap-usb-host: Use clock names as per function for reference
>     clocks
>   mfd: omap-usb-host: Update DT clock binding information
>   mfd: omap-usb-tll: Update DT clock binding information
>   ARM: OMAP2+: Remove legacy_init_ehci_clk()
>   ARM: dts: OMAP2+: Get rid of incompatible ids for USB host nodes
>   usb: omap: dts: Update DT binding example usage
> 
>  .../devicetree/bindings/mfd/omap-usb-host.txt      |  23 ++++
>  .../devicetree/bindings/mfd/omap-usb-tll.txt       |  10 ++
>  .../devicetree/bindings/usb/ehci-omap.txt          |   2 +-
>  .../devicetree/bindings/usb/ohci-omap3.txt         |   2 +-
>  arch/arm/boot/dts/omap3.dtsi                       |   4 +-
>  arch/arm/boot/dts/omap4-panda-common.dtsi          |   8 +-
>  arch/arm/boot/dts/omap4.dtsi                       |  10 +-
>  arch/arm/boot/dts/omap5-uevm.dts                   |   8 +-
>  arch/arm/boot/dts/omap5.dtsi                       |  10 +-
>  arch/arm/mach-omap2/cclock3xxx_data.c              |   4 -
>  arch/arm/mach-omap2/omap_hwmod_3xxx_data.c         |   6 --
>  arch/arm/mach-omap2/pdata-quirks.c                 |  16 ---
>  drivers/clk/ti/clk-3xxx.c                          |   4 -
>  drivers/mfd/omap-usb-host.c                        | 116 ++++++++++++++-------
>  14 files changed, 135 insertions(+), 88 deletions(-)
> 

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Roger Quadros]

Hi Lee,

On 02/27/2014 04:18 PM, Roger Quadros wrote:
> Hi,
> 
> This patchset brings up USB Host ports and Ethernet port on
> the OMAP5 uEVM board.
> 
> It also does some cleanup with respect to DT clock binding
> for the mfd/omap-usb-host driver.
> 
> Please queue these for -next.
> 
> Lee,
> 
> I've folded some platform data dependent patches with mfd patches
> so that they don't break functionality when applied individually.
> You can safely pull in all MFD patches (1 to 6).
> 
> Tony & Benoit,
> 
> Can you please accept patches 7, 8 and 9?

Tony has already picked up 7,8 and 9 through omap-soc tree.

Since you acked most patches except 5 and 6, are you fine if Tony takes
all the patches 1 to 4 in this series via omap-soc tree?

What about patches 5 and 6?

cheers,
-roger

> 
> Thanks.
> 
> Tested on:
>  - OMAP5 uEVM
>  - Pandaboard ES Rev. B1
>  - Beagleboard-XM Rev C2 (DT + Legacy)
>  - Beagleboard Rev C4 (DT + Legacy)
> 
> Changelog:
> 
> v9:
> - Folded dependent platform data patches into MFD patches.
> 
> v8:
> - Addressed review comments and split patch
>   "mfd: omap-usb-host: Get clocks based on hardware revision"
> - Removed unnecessary usb host dummy clocks on OMAP3
> - Removed unnecessary clock alias "ehci_logic_fck" for OMAP3
> - Rebased on 3.14-rc3
> 
> v7:
> - Rebased on 3.14-rc2
> - Removed incompatible ids from DT files and examples
> 
> v6:
> - Initialized clocks to -ENODEV and split patch 3.
> 
> v5:
> - Expose all clocks in the DT binding document for mfd:omap-usb-host
> and mfd:omap-usb-tll
> 
> v4:
> - Updated DT binding document for clock binding
> 
> v3:
> - Rebased on top of 3.13-rc7
> 
> cheers,
> -roger
> 
> ---
> Roger Quadros (9):
>   mfd: omap-usb-host: Get clocks based on hardware revision
>   mfd: omap-usb-host: Always fail on clk_get() error
>   mfd: omap-usb-host: Use proper clock name instead of alias
>   mfd: omap-usb-host: Use clock names as per function for reference
>     clocks
>   mfd: omap-usb-host: Update DT clock binding information
>   mfd: omap-usb-tll: Update DT clock binding information
>   ARM: OMAP2+: Remove legacy_init_ehci_clk()
>   ARM: dts: OMAP2+: Get rid of incompatible ids for USB host nodes
>   usb: omap: dts: Update DT binding example usage
> 
>  .../devicetree/bindings/mfd/omap-usb-host.txt      |  23 ++++
>  .../devicetree/bindings/mfd/omap-usb-tll.txt       |  10 ++
>  .../devicetree/bindings/usb/ehci-omap.txt          |   2 +-
>  .../devicetree/bindings/usb/ohci-omap3.txt         |   2 +-
>  arch/arm/boot/dts/omap3.dtsi                       |   4 +-
>  arch/arm/boot/dts/omap4-panda-common.dtsi          |   8 +-
>  arch/arm/boot/dts/omap4.dtsi                       |  10 +-
>  arch/arm/boot/dts/omap5-uevm.dts                   |   8 +-
>  arch/arm/boot/dts/omap5.dtsi                       |  10 +-
>  arch/arm/mach-omap2/cclock3xxx_data.c              |   4 -
>  arch/arm/mach-omap2/omap_hwmod_3xxx_data.c         |   6 --
>  arch/arm/mach-omap2/pdata-quirks.c                 |  16 ---
>  drivers/clk/ti/clk-3xxx.c                          |   4 -
>  drivers/mfd/omap-usb-host.c                        | 116 ++++++++++++++-------
>  14 files changed, 135 insertions(+), 88 deletions(-)
> 

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Roger Quadros]

Hi Lee,

On 02/27/2014 04:18 PM, Roger Quadros wrote:
> Hi,
> 
> This patchset brings up USB Host ports and Ethernet port on
> the OMAP5 uEVM board.
> 
> It also does some cleanup with respect to DT clock binding
> for the mfd/omap-usb-host driver.
> 
> Please queue these for -next.
> 
> Lee,
> 
> I've folded some platform data dependent patches with mfd patches
> so that they don't break functionality when applied individually.
> You can safely pull in all MFD patches (1 to 6).
> 
> Tony & Benoit,
> 
> Can you please accept patches 7, 8 and 9?

Tony has already picked up 7,8 and 9 through omap-soc tree.

Since you acked most patches except 5 and 6, are you fine if Tony takes
all the patches 1 to 4 in this series via omap-soc tree?

What about patches 5 and 6?

cheers,
-roger

> 
> Thanks.
> 
> Tested on:
>  - OMAP5 uEVM
>  - Pandaboard ES Rev. B1
>  - Beagleboard-XM Rev C2 (DT + Legacy)
>  - Beagleboard Rev C4 (DT + Legacy)
> 
> Changelog:
> 
> v9:
> - Folded dependent platform data patches into MFD patches.
> 
> v8:
> - Addressed review comments and split patch
>   "mfd: omap-usb-host: Get clocks based on hardware revision"
> - Removed unnecessary usb host dummy clocks on OMAP3
> - Removed unnecessary clock alias "ehci_logic_fck" for OMAP3
> - Rebased on 3.14-rc3
> 
> v7:
> - Rebased on 3.14-rc2
> - Removed incompatible ids from DT files and examples
> 
> v6:
> - Initialized clocks to -ENODEV and split patch 3.
> 
> v5:
> - Expose all clocks in the DT binding document for mfd:omap-usb-host
> and mfd:omap-usb-tll
> 
> v4:
> - Updated DT binding document for clock binding
> 
> v3:
> - Rebased on top of 3.13-rc7
> 
> cheers,
> -roger
> 
> ---
> Roger Quadros (9):
>   mfd: omap-usb-host: Get clocks based on hardware revision
>   mfd: omap-usb-host: Always fail on clk_get() error
>   mfd: omap-usb-host: Use proper clock name instead of alias
>   mfd: omap-usb-host: Use clock names as per function for reference
>     clocks
>   mfd: omap-usb-host: Update DT clock binding information
>   mfd: omap-usb-tll: Update DT clock binding information
>   ARM: OMAP2+: Remove legacy_init_ehci_clk()
>   ARM: dts: OMAP2+: Get rid of incompatible ids for USB host nodes
>   usb: omap: dts: Update DT binding example usage
> 
>  .../devicetree/bindings/mfd/omap-usb-host.txt      |  23 ++++
>  .../devicetree/bindings/mfd/omap-usb-tll.txt       |  10 ++
>  .../devicetree/bindings/usb/ehci-omap.txt          |   2 +-
>  .../devicetree/bindings/usb/ohci-omap3.txt         |   2 +-
>  arch/arm/boot/dts/omap3.dtsi                       |   4 +-
>  arch/arm/boot/dts/omap4-panda-common.dtsi          |   8 +-
>  arch/arm/boot/dts/omap4.dtsi                       |  10 +-
>  arch/arm/boot/dts/omap5-uevm.dts                   |   8 +-
>  arch/arm/boot/dts/omap5.dtsi                       |  10 +-
>  arch/arm/mach-omap2/cclock3xxx_data.c              |   4 -
>  arch/arm/mach-omap2/omap_hwmod_3xxx_data.c         |   6 --
>  arch/arm/mach-omap2/pdata-quirks.c                 |  16 ---
>  drivers/clk/ti/clk-3xxx.c                          |   4 -
>  drivers/mfd/omap-usb-host.c                        | 116 ++++++++++++++-------
>  14 files changed, 135 insertions(+), 88 deletions(-)
> 

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Lee Jones]

> > Hi,
> > 
> > This patchset brings up USB Host ports and Ethernet port on
> > the OMAP5 uEVM board.
> > 
> > It also does some cleanup with respect to DT clock binding
> > for the mfd/omap-usb-host driver.
> > 
> > Please queue these for -next.
> > 
> > Lee,
> > 
> > I've folded some platform data dependent patches with mfd patches
> > so that they don't break functionality when applied individually.
> > You can safely pull in all MFD patches (1 to 6).
> > 
> > Tony & Benoit,
> > 
> > Can you please accept patches 7, 8 and 9?
> 
> Tony has already picked up 7,8 and 9 through omap-soc tree.
> 
> Since you acked most patches except 5 and 6, are you fine if Tony takes
> all the patches 1 to 4 in this series via omap-soc tree?
> 
> What about patches 5 and 6?

Any patches which are orthogonal can just be sucked into whichever tree
they belong in. If there are inter-subsystem dependencies I'd prefer
to take them and issue a immutable branch pull-request to the other
maintainers.

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Lee Jones]

> > Hi,
> > 
> > This patchset brings up USB Host ports and Ethernet port on
> > the OMAP5 uEVM board.
> > 
> > It also does some cleanup with respect to DT clock binding
> > for the mfd/omap-usb-host driver.
> > 
> > Please queue these for -next.
> > 
> > Lee,
> > 
> > I've folded some platform data dependent patches with mfd patches
> > so that they don't break functionality when applied individually.
> > You can safely pull in all MFD patches (1 to 6).
> > 
> > Tony & Benoit,
> > 
> > Can you please accept patches 7, 8 and 9?
> 
> Tony has already picked up 7,8 and 9 through omap-soc tree.
> 
> Since you acked most patches except 5 and 6, are you fine if Tony takes
> all the patches 1 to 4 in this series via omap-soc tree?
> 
> What about patches 5 and 6?

Any patches which are orthogonal can just be sucked into whichever tree
they belong in. If there are inter-subsystem dependencies I'd prefer
to take them and issue a immutable branch pull-request to the other
maintainers.

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Lee Jones]

> > Hi,
> > 
> > This patchset brings up USB Host ports and Ethernet port on
> > the OMAP5 uEVM board.
> > 
> > It also does some cleanup with respect to DT clock binding
> > for the mfd/omap-usb-host driver.
> > 
> > Please queue these for -next.
> > 
> > Lee,
> > 
> > I've folded some platform data dependent patches with mfd patches
> > so that they don't break functionality when applied individually.
> > You can safely pull in all MFD patches (1 to 6).
> > 
> > Tony & Benoit,
> > 
> > Can you please accept patches 7, 8 and 9?
> 
> Tony has already picked up 7,8 and 9 through omap-soc tree.
> 
> Since you acked most patches except 5 and 6, are you fine if Tony takes
> all the patches 1 to 4 in this series via omap-soc tree?
> 
> What about patches 5 and 6?

Any patches which are orthogonal can just be sucked into whichever tree
they belong in. If there are inter-subsystem dependencies I'd prefer
to take them and issue a immutable branch pull-request to the other
maintainers.

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Roger Quadros]

On 03/11/2014 02:02 PM, Lee Jones wrote:
>>> Hi,
>>>
>>> This patchset brings up USB Host ports and Ethernet port on
>>> the OMAP5 uEVM board.
>>>
>>> It also does some cleanup with respect to DT clock binding
>>> for the mfd/omap-usb-host driver.
>>>
>>> Please queue these for -next.
>>>
>>> Lee,
>>>
>>> I've folded some platform data dependent patches with mfd patches
>>> so that they don't break functionality when applied individually.
>>> You can safely pull in all MFD patches (1 to 6).
>>>
>>> Tony & Benoit,
>>>
>>> Can you please accept patches 7, 8 and 9?
>>
>> Tony has already picked up 7,8 and 9 through omap-soc tree.
>>
>> Since you acked most patches except 5 and 6, are you fine if Tony takes
>> all the patches 1 to 4 in this series via omap-soc tree?
>>
>> What about patches 5 and 6?
> 
> Any patches which are orthogonal can just be sucked into whichever tree
> they belong in. If there are inter-subsystem dependencies I'd prefer
> to take them and issue a immutable branch pull-request to the other
> maintainers.
> 
Awesome. That would be great, thanks.

cheers,
-roger

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Roger Quadros]

On 03/11/2014 02:02 PM, Lee Jones wrote:
>>> Hi,
>>>
>>> This patchset brings up USB Host ports and Ethernet port on
>>> the OMAP5 uEVM board.
>>>
>>> It also does some cleanup with respect to DT clock binding
>>> for the mfd/omap-usb-host driver.
>>>
>>> Please queue these for -next.
>>>
>>> Lee,
>>>
>>> I've folded some platform data dependent patches with mfd patches
>>> so that they don't break functionality when applied individually.
>>> You can safely pull in all MFD patches (1 to 6).
>>>
>>> Tony & Benoit,
>>>
>>> Can you please accept patches 7, 8 and 9?
>>
>> Tony has already picked up 7,8 and 9 through omap-soc tree.
>>
>> Since you acked most patches except 5 and 6, are you fine if Tony takes
>> all the patches 1 to 4 in this series via omap-soc tree?
>>
>> What about patches 5 and 6?
> 
> Any patches which are orthogonal can just be sucked into whichever tree
> they belong in. If there are inter-subsystem dependencies I'd prefer
> to take them and issue a immutable branch pull-request to the other
> maintainers.
> 
Awesome. That would be great, thanks.

cheers,
-roger

[PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Roger Quadros]

On 03/11/2014 02:02 PM, Lee Jones wrote:
>>> Hi,
>>>
>>> This patchset brings up USB Host ports and Ethernet port on
>>> the OMAP5 uEVM board.
>>>
>>> It also does some cleanup with respect to DT clock binding
>>> for the mfd/omap-usb-host driver.
>>>
>>> Please queue these for -next.
>>>
>>> Lee,
>>>
>>> I've folded some platform data dependent patches with mfd patches
>>> so that they don't break functionality when applied individually.
>>> You can safely pull in all MFD patches (1 to 6).
>>>
>>> Tony & Benoit,
>>>
>>> Can you please accept patches 7, 8 and 9?
>>
>> Tony has already picked up 7,8 and 9 through omap-soc tree.
>>
>> Since you acked most patches except 5 and 6, are you fine if Tony takes
>> all the patches 1 to 4 in this series via omap-soc tree?
>>
>> What about patches 5 and 6?
> 
> Any patches which are orthogonal can just be sucked into whichever tree
> they belong in. If there are inter-subsystem dependencies I'd prefer
> to take them and issue a immutable branch pull-request to the other
> maintainers.
> 
Awesome. That would be great, thanks.

cheers,
-roger

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Lee Jones]

> >>> This patchset brings up USB Host ports and Ethernet port on
> >>> the OMAP5 uEVM board.
> >>>
> >>> It also does some cleanup with respect to DT clock binding
> >>> for the mfd/omap-usb-host driver.
> >>>
> >>> Please queue these for -next.
> >>>
> >>> Lee,
> >>>
> >>> I've folded some platform data dependent patches with mfd patches
> >>> so that they don't break functionality when applied individually.
> >>> You can safely pull in all MFD patches (1 to 6).
> >>>
> >>> Tony & Benoit,
> >>>
> >>> Can you please accept patches 7, 8 and 9?
> >>
> >> Tony has already picked up 7,8 and 9 through omap-soc tree.
> >>
> >> Since you acked most patches except 5 and 6, are you fine if Tony takes
> >> all the patches 1 to 4 in this series via omap-soc tree?
> >>
> >> What about patches 5 and 6?
> > 
> > Any patches which are orthogonal can just be sucked into whichever tree
> > they belong in. If there are inter-subsystem dependencies I'd prefer
> > to take them and issue a immutable branch pull-request to the other
> > maintainers.
> > 
> Awesome. That would be great, thanks.

That does mean I need a) all of the Maintainer Acks and b) you to tell
me which ones need to go through a single tree.

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Lee Jones]

> >>> This patchset brings up USB Host ports and Ethernet port on
> >>> the OMAP5 uEVM board.
> >>>
> >>> It also does some cleanup with respect to DT clock binding
> >>> for the mfd/omap-usb-host driver.
> >>>
> >>> Please queue these for -next.
> >>>
> >>> Lee,
> >>>
> >>> I've folded some platform data dependent patches with mfd patches
> >>> so that they don't break functionality when applied individually.
> >>> You can safely pull in all MFD patches (1 to 6).
> >>>
> >>> Tony & Benoit,
> >>>
> >>> Can you please accept patches 7, 8 and 9?
> >>
> >> Tony has already picked up 7,8 and 9 through omap-soc tree.
> >>
> >> Since you acked most patches except 5 and 6, are you fine if Tony takes
> >> all the patches 1 to 4 in this series via omap-soc tree?
> >>
> >> What about patches 5 and 6?
> > 
> > Any patches which are orthogonal can just be sucked into whichever tree
> > they belong in. If there are inter-subsystem dependencies I'd prefer
> > to take them and issue a immutable branch pull-request to the other
> > maintainers.
> > 
> Awesome. That would be great, thanks.

That does mean I need a) all of the Maintainer Acks and b) you to tell
me which ones need to go through a single tree.

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Roger Quadros]

On 03/11/2014 03:07 PM, Lee Jones wrote:
> 
>>>>> This patchset brings up USB Host ports and Ethernet port on
>>>>> the OMAP5 uEVM board.
>>>>>
>>>>> It also does some cleanup with respect to DT clock binding
>>>>> for the mfd/omap-usb-host driver.
>>>>>
>>>>> Please queue these for -next.
>>>>>
>>>>> Lee,
>>>>>
>>>>> I've folded some platform data dependent patches with mfd patches
>>>>> so that they don't break functionality when applied individually.
>>>>> You can safely pull in all MFD patches (1 to 6).
>>>>>
>>>>> Tony & Benoit,
>>>>>
>>>>> Can you please accept patches 7, 8 and 9?
>>>>
>>>> Tony has already picked up 7,8 and 9 through omap-soc tree.
>>>>
>>>> Since you acked most patches except 5 and 6, are you fine if Tony takes
>>>> all the patches 1 to 4 in this series via omap-soc tree?
>>>>
>>>> What about patches 5 and 6?
>>>
>>> Any patches which are orthogonal can just be sucked into whichever tree
>>> they belong in. If there are inter-subsystem dependencies I'd prefer
>>> to take them and issue a immutable branch pull-request to the other
>>> maintainers.
>>>
>> Awesome. That would be great, thanks.
> 
> That does mean I need a) all of the Maintainer Acks and b) you to tell
> me which ones need to go through a single tree.
> 

You need to take patches 1 to 6 in the MFD tree. Out of these, patches 1 to 4
need to be shared with Tony as an immutable branch.

Tony, could you please Ack patches 1 to 4? Thanks.

cheers,
-roger

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Roger Quadros]

On 03/11/2014 03:07 PM, Lee Jones wrote:
> 
>>>>> This patchset brings up USB Host ports and Ethernet port on
>>>>> the OMAP5 uEVM board.
>>>>>
>>>>> It also does some cleanup with respect to DT clock binding
>>>>> for the mfd/omap-usb-host driver.
>>>>>
>>>>> Please queue these for -next.
>>>>>
>>>>> Lee,
>>>>>
>>>>> I've folded some platform data dependent patches with mfd patches
>>>>> so that they don't break functionality when applied individually.
>>>>> You can safely pull in all MFD patches (1 to 6).
>>>>>
>>>>> Tony & Benoit,
>>>>>
>>>>> Can you please accept patches 7, 8 and 9?
>>>>
>>>> Tony has already picked up 7,8 and 9 through omap-soc tree.
>>>>
>>>> Since you acked most patches except 5 and 6, are you fine if Tony takes
>>>> all the patches 1 to 4 in this series via omap-soc tree?
>>>>
>>>> What about patches 5 and 6?
>>>
>>> Any patches which are orthogonal can just be sucked into whichever tree
>>> they belong in. If there are inter-subsystem dependencies I'd prefer
>>> to take them and issue a immutable branch pull-request to the other
>>> maintainers.
>>>
>> Awesome. That would be great, thanks.
> 
> That does mean I need a) all of the Maintainer Acks and b) you to tell
> me which ones need to go through a single tree.
> 

You need to take patches 1 to 6 in the MFD tree. Out of these, patches 1 to 4
need to be shared with Tony as an immutable branch.

Tony, could you please Ack patches 1 to 4? Thanks.

cheers,
-roger

[PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Roger Quadros]

On 03/11/2014 03:07 PM, Lee Jones wrote:
> 
>>>>> This patchset brings up USB Host ports and Ethernet port on
>>>>> the OMAP5 uEVM board.
>>>>>
>>>>> It also does some cleanup with respect to DT clock binding
>>>>> for the mfd/omap-usb-host driver.
>>>>>
>>>>> Please queue these for -next.
>>>>>
>>>>> Lee,
>>>>>
>>>>> I've folded some platform data dependent patches with mfd patches
>>>>> so that they don't break functionality when applied individually.
>>>>> You can safely pull in all MFD patches (1 to 6).
>>>>>
>>>>> Tony & Benoit,
>>>>>
>>>>> Can you please accept patches 7, 8 and 9?
>>>>
>>>> Tony has already picked up 7,8 and 9 through omap-soc tree.
>>>>
>>>> Since you acked most patches except 5 and 6, are you fine if Tony takes
>>>> all the patches 1 to 4 in this series via omap-soc tree?
>>>>
>>>> What about patches 5 and 6?
>>>
>>> Any patches which are orthogonal can just be sucked into whichever tree
>>> they belong in. If there are inter-subsystem dependencies I'd prefer
>>> to take them and issue a immutable branch pull-request to the other
>>> maintainers.
>>>
>> Awesome. That would be great, thanks.
> 
> That does mean I need a) all of the Maintainer Acks and b) you to tell
> me which ones need to go through a single tree.
> 

You need to take patches 1 to 6 in the MFD tree. Out of these, patches 1 to 4
need to be shared with Tony as an immutable branch.

Tony, could you please Ack patches 1 to 4? Thanks.

cheers,
-roger

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Tony Lindgren]

* Roger Quadros <rogerq@ti.com> [140311 06:13]:
> On 03/11/2014 03:07 PM, Lee Jones wrote:
> > 
> >>>>> This patchset brings up USB Host ports and Ethernet port on
> >>>>> the OMAP5 uEVM board.
> >>>>>
> >>>>> It also does some cleanup with respect to DT clock binding
> >>>>> for the mfd/omap-usb-host driver.
> >>>>>
> >>>>> Please queue these for -next.
> >>>>>
> >>>>> Lee,
> >>>>>
> >>>>> I've folded some platform data dependent patches with mfd patches
> >>>>> so that they don't break functionality when applied individually.
> >>>>> You can safely pull in all MFD patches (1 to 6).
> >>>>>
> >>>>> Tony & Benoit,
> >>>>>
> >>>>> Can you please accept patches 7, 8 and 9?
> >>>>
> >>>> Tony has already picked up 7,8 and 9 through omap-soc tree.
> >>>>
> >>>> Since you acked most patches except 5 and 6, are you fine if Tony takes
> >>>> all the patches 1 to 4 in this series via omap-soc tree?
> >>>>
> >>>> What about patches 5 and 6?
> >>>
> >>> Any patches which are orthogonal can just be sucked into whichever tree
> >>> they belong in. If there are inter-subsystem dependencies I'd prefer
> >>> to take them and issue a immutable branch pull-request to the other
> >>> maintainers.
> >>>
> >> Awesome. That would be great, thanks.
> > 
> > That does mean I need a) all of the Maintainer Acks and b) you to tell
> > me which ones need to go through a single tree.
> > 
> 
> You need to take patches 1 to 6 in the MFD tree. Out of these, patches 1 to 4
> need to be shared with Tony as an immutable branch.
> 
> Tony, could you please Ack patches 1 to 4? Thanks.

Changes in 1 to 6 look OK to me, so for those please feel free to add:

Acked-by: Tony Lindgren <tony@atomide.com>

[PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Tony Lindgren]

* Roger Quadros <rogerq@ti.com> [140311 06:13]:
> On 03/11/2014 03:07 PM, Lee Jones wrote:
> > 
> >>>>> This patchset brings up USB Host ports and Ethernet port on
> >>>>> the OMAP5 uEVM board.
> >>>>>
> >>>>> It also does some cleanup with respect to DT clock binding
> >>>>> for the mfd/omap-usb-host driver.
> >>>>>
> >>>>> Please queue these for -next.
> >>>>>
> >>>>> Lee,
> >>>>>
> >>>>> I've folded some platform data dependent patches with mfd patches
> >>>>> so that they don't break functionality when applied individually.
> >>>>> You can safely pull in all MFD patches (1 to 6).
> >>>>>
> >>>>> Tony & Benoit,
> >>>>>
> >>>>> Can you please accept patches 7, 8 and 9?
> >>>>
> >>>> Tony has already picked up 7,8 and 9 through omap-soc tree.
> >>>>
> >>>> Since you acked most patches except 5 and 6, are you fine if Tony takes
> >>>> all the patches 1 to 4 in this series via omap-soc tree?
> >>>>
> >>>> What about patches 5 and 6?
> >>>
> >>> Any patches which are orthogonal can just be sucked into whichever tree
> >>> they belong in. If there are inter-subsystem dependencies I'd prefer
> >>> to take them and issue a immutable branch pull-request to the other
> >>> maintainers.
> >>>
> >> Awesome. That would be great, thanks.
> > 
> > That does mean I need a) all of the Maintainer Acks and b) you to tell
> > me which ones need to go through a single tree.
> > 
> 
> You need to take patches 1 to 6 in the MFD tree. Out of these, patches 1 to 4
> need to be shared with Tony as an immutable branch.
> 
> Tony, could you please Ack patches 1 to 4? Thanks.

Changes in 1 to 6 look OK to me, so for those please feel free to add:

Acked-by: Tony Lindgren <tony@atomide.com>

Re: [PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Lee Jones]

> > > That does mean I need a) all of the Maintainer Acks and b) you to tell
> > > me which ones need to go through a single tree.
> > 
> > You need to take patches 1 to 6 in the MFD tree. Out of these, patches 1 to 4
> > need to be shared with Tony as an immutable branch.
> > 
> > Tony, could you please Ack patches 1 to 4? Thanks.
> 
> Changes in 1 to 6 look OK to me, so for those please feel free to add:
> 
> Acked-by: Tony Lindgren <tony@atomide.com>

The following changes since commit 0414855fdc4a40da05221fc6062cccbc0c30f169:

  Linux 3.14-rc5 (2014-03-02 18:56:16 -0800)

are available in the git repository at:

  git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git ib-mfd-omap

for you to fetch changes up to 2e1b365cea4a0a750b8ffd4bc6ca5e9e8020f53e:

  mfd: omap-usb-tll: Update DT clock binding information (2014-03-13 22:27:17 +0000)

----------------------------------------------------------------
Colin Ian King (1):
      mfd: omap-usb-tll: Fix cppcheck sizeof warning

Roger Quadros (7):
      mfd: omap-usb-host: Use resource managed clk_get()
      mfd: omap-usb-host: Get clocks based on hardware revision
      mfd: omap-usb-host: Always fail on clk_get() error
      mfd: omap-usb-host: Use proper clock name instead of alias
      mfd: omap-usb-host: Use clock names as per function for reference clocks
      mfd: omap-usb-host: Update DT clock binding information
      mfd: omap-usb-tll: Update DT clock binding information

 Documentation/devicetree/bindings/mfd/omap-usb-host.txt |  23 ++++++++++++++
 Documentation/devicetree/bindings/mfd/omap-usb-tll.txt  |  10 ++++++
 arch/arm/boot/dts/omap4.dtsi                            |   6 ++++
 arch/arm/boot/dts/omap5.dtsi                            |   6 ++++
 arch/arm/mach-omap2/cclock3xxx_data.c                   |   4 ---
 arch/arm/mach-omap2/omap_hwmod_3xxx_data.c              |   6 ----
 drivers/clk/ti/clk-3xxx.c                               |   4 ---
 drivers/mfd/omap-usb-host.c                             | 189 +++++++++++++++++++++++++++++++++++++++++++++++++++++----------------------------------------------------------
 drivers/mfd/omap-usb-tll.c                              |   2 +-
 9 files changed, 136 insertions(+), 114 deletions(-)

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH v9 0/9] USB Host support for OMAP5 uEVM

[Lee Jones]

> > > That does mean I need a) all of the Maintainer Acks and b) you to tell
> > > me which ones need to go through a single tree.
> > 
> > You need to take patches 1 to 6 in the MFD tree. Out of these, patches 1 to 4
> > need to be shared with Tony as an immutable branch.
> > 
> > Tony, could you please Ack patches 1 to 4? Thanks.
> 
> Changes in 1 to 6 look OK to me, so for those please feel free to add:
> 
> Acked-by: Tony Lindgren <tony@atomide.com>

The following changes since commit 0414855fdc4a40da05221fc6062cccbc0c30f169:

  Linux 3.14-rc5 (2014-03-02 18:56:16 -0800)

are available in the git repository at:

  git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git ib-mfd-omap

for you to fetch changes up to 2e1b365cea4a0a750b8ffd4bc6ca5e9e8020f53e:

  mfd: omap-usb-tll: Update DT clock binding information (2014-03-13 22:27:17 +0000)

----------------------------------------------------------------
Colin Ian King (1):
      mfd: omap-usb-tll: Fix cppcheck sizeof warning

Roger Quadros (7):
      mfd: omap-usb-host: Use resource managed clk_get()
      mfd: omap-usb-host: Get clocks based on hardware revision
      mfd: omap-usb-host: Always fail on clk_get() error
      mfd: omap-usb-host: Use proper clock name instead of alias
      mfd: omap-usb-host: Use clock names as per function for reference clocks
      mfd: omap-usb-host: Update DT clock binding information
      mfd: omap-usb-tll: Update DT clock binding information

 Documentation/devicetree/bindings/mfd/omap-usb-host.txt |  23 ++++++++++++++
 Documentation/devicetree/bindings/mfd/omap-usb-tll.txt  |  10 ++++++
 arch/arm/boot/dts/omap4.dtsi                            |   6 ++++
 arch/arm/boot/dts/omap5.dtsi                            |   6 ++++
 arch/arm/mach-omap2/cclock3xxx_data.c                   |   4 ---
 arch/arm/mach-omap2/omap_hwmod_3xxx_data.c              |   6 ----
 drivers/clk/ti/clk-3xxx.c                               |   4 ---
 drivers/mfd/omap-usb-host.c                             | 189 +++++++++++++++++++++++++++++++++++++++++++++++++++++----------------------------------------------------------
 drivers/mfd/omap-usb-tll.c                              |   2 +-
 9 files changed, 136 insertions(+), 114 deletions(-)

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog