* [PATCH v5 0/2] ARM: mach-moxart: add MOXA ART SoC support
@ 2013-12-17 15:38 ` Jonas Jensen
0 siblings, 0 replies; 16+ messages in thread
From: Jonas Jensen @ 2013-12-17 15:38 UTC (permalink / raw)
To: linux-arm-kernel
Cc: linux-kernel, devicetree, arm, linux, arnd, olof,
soren.brinkmann, peter.crosthwaite, linux, Jonas Jensen
Thanks for the replies!
This should tick the boxes on your feedback.
Changes since v4:
1. remove all platform specific code
2. move all SoC common nodes (SDHCI,MAC,UART) to dtsi,
enable them in board file
3. added moxart_defconfig options:
CONFIG_PACKET=y
CONFIG_IP_MULTICAST=y
4. removed moxart_defconfig options:
# CONFIG_ARM_THUMB is not set
Applies to next-20131217
Jonas Jensen (2):
ARM: mach-moxart: add MOXA ART SoC platform files
ARM: mach-moxart: add MOXA ART SoC device tree files
Documentation/devicetree/bindings/arm/moxart.txt | 12 ++
arch/arm/Kconfig | 2 +
arch/arm/Makefile | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/moxart-uc7112lx.dts | 93 +++++++++++++
arch/arm/boot/dts/moxart.dtsi | 167 +++++++++++++++++++++++
arch/arm/configs/moxart_defconfig | 149 ++++++++++++++++++++
arch/arm/mach-moxart/Kconfig | 31 +++++
arch/arm/mach-moxart/Makefile | 3 +
arch/arm/mach-moxart/moxart.c | 15 ++
10 files changed, 474 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/moxart.txt
create mode 100644 arch/arm/boot/dts/moxart-uc7112lx.dts
create mode 100644 arch/arm/boot/dts/moxart.dtsi
create mode 100644 arch/arm/configs/moxart_defconfig
create mode 100644 arch/arm/mach-moxart/Kconfig
create mode 100644 arch/arm/mach-moxart/Makefile
create mode 100644 arch/arm/mach-moxart/moxart.c
--
1.8.2.1
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v5 0/2] ARM: mach-moxart: add MOXA ART SoC support
@ 2013-12-17 15:38 ` Jonas Jensen
0 siblings, 0 replies; 16+ messages in thread
From: Jonas Jensen @ 2013-12-17 15:38 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA, arm-DgEjT+Ai2ygdnm+yROfE0A,
linux-lFZ/pmaqli7XmaaqVzeoHQ, arnd-r2nGTMty4D4,
olof-nZhT3qVonbNeoWH0uzbU5w,
soren.brinkmann-gjFFaj9aHVfQT0dZR+AlfA,
peter.crosthwaite-gjFFaj9aHVfQT0dZR+AlfA,
linux-0h96xk9xTtrk1uMJSBkQmQ, Jonas Jensen
Thanks for the replies!
This should tick the boxes on your feedback.
Changes since v4:
1. remove all platform specific code
2. move all SoC common nodes (SDHCI,MAC,UART) to dtsi,
enable them in board file
3. added moxart_defconfig options:
CONFIG_PACKET=y
CONFIG_IP_MULTICAST=y
4. removed moxart_defconfig options:
# CONFIG_ARM_THUMB is not set
Applies to next-20131217
Jonas Jensen (2):
ARM: mach-moxart: add MOXA ART SoC platform files
ARM: mach-moxart: add MOXA ART SoC device tree files
Documentation/devicetree/bindings/arm/moxart.txt | 12 ++
arch/arm/Kconfig | 2 +
arch/arm/Makefile | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/moxart-uc7112lx.dts | 93 +++++++++++++
arch/arm/boot/dts/moxart.dtsi | 167 +++++++++++++++++++++++
arch/arm/configs/moxart_defconfig | 149 ++++++++++++++++++++
arch/arm/mach-moxart/Kconfig | 31 +++++
arch/arm/mach-moxart/Makefile | 3 +
arch/arm/mach-moxart/moxart.c | 15 ++
10 files changed, 474 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/moxart.txt
create mode 100644 arch/arm/boot/dts/moxart-uc7112lx.dts
create mode 100644 arch/arm/boot/dts/moxart.dtsi
create mode 100644 arch/arm/configs/moxart_defconfig
create mode 100644 arch/arm/mach-moxart/Kconfig
create mode 100644 arch/arm/mach-moxart/Makefile
create mode 100644 arch/arm/mach-moxart/moxart.c
--
1.8.2.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v5 0/2] ARM: mach-moxart: add MOXA ART SoC support
@ 2013-12-17 15:38 ` Jonas Jensen
0 siblings, 0 replies; 16+ messages in thread
From: Jonas Jensen @ 2013-12-17 15:38 UTC (permalink / raw)
To: linux-arm-kernel
Thanks for the replies!
This should tick the boxes on your feedback.
Changes since v4:
1. remove all platform specific code
2. move all SoC common nodes (SDHCI,MAC,UART) to dtsi,
enable them in board file
3. added moxart_defconfig options:
CONFIG_PACKET=y
CONFIG_IP_MULTICAST=y
4. removed moxart_defconfig options:
# CONFIG_ARM_THUMB is not set
Applies to next-20131217
Jonas Jensen (2):
ARM: mach-moxart: add MOXA ART SoC platform files
ARM: mach-moxart: add MOXA ART SoC device tree files
Documentation/devicetree/bindings/arm/moxart.txt | 12 ++
arch/arm/Kconfig | 2 +
arch/arm/Makefile | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/moxart-uc7112lx.dts | 93 +++++++++++++
arch/arm/boot/dts/moxart.dtsi | 167 +++++++++++++++++++++++
arch/arm/configs/moxart_defconfig | 149 ++++++++++++++++++++
arch/arm/mach-moxart/Kconfig | 31 +++++
arch/arm/mach-moxart/Makefile | 3 +
arch/arm/mach-moxart/moxart.c | 15 ++
10 files changed, 474 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/moxart.txt
create mode 100644 arch/arm/boot/dts/moxart-uc7112lx.dts
create mode 100644 arch/arm/boot/dts/moxart.dtsi
create mode 100644 arch/arm/configs/moxart_defconfig
create mode 100644 arch/arm/mach-moxart/Kconfig
create mode 100644 arch/arm/mach-moxart/Makefile
create mode 100644 arch/arm/mach-moxart/moxart.c
--
1.8.2.1
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v5 1/2] ARM: mach-moxart: add MOXA ART SoC platform files
2013-12-17 15:38 ` Jonas Jensen
@ 2013-12-17 15:38 ` Jonas Jensen
-1 siblings, 0 replies; 16+ messages in thread
From: Jonas Jensen @ 2013-12-17 15:38 UTC (permalink / raw)
To: linux-arm-kernel
Cc: linux-kernel, devicetree, arm, linux, arnd, olof,
soren.brinkmann, peter.crosthwaite, linux, Jonas Jensen
The MOXA ART SoC is based on Faraday's FA526. This is a ARMv4 32-bit
192 MHz CPU with MMU and 16KB/8KB D/I-cache.
Add platform support for this SoC.
Also add UC-7112-LX as a machine.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
---
arch/arm/Kconfig | 2 +
arch/arm/Makefile | 1 +
arch/arm/configs/moxart_defconfig | 149 ++++++++++++++++++++++++++++++++++++++
arch/arm/mach-moxart/Kconfig | 31 ++++++++
arch/arm/mach-moxart/Makefile | 3 +
arch/arm/mach-moxart/moxart.c | 15 ++++
6 files changed, 201 insertions(+)
create mode 100644 arch/arm/configs/moxart_defconfig
create mode 100644 arch/arm/mach-moxart/Kconfig
create mode 100644 arch/arm/mach-moxart/Makefile
create mode 100644 arch/arm/mach-moxart/moxart.c
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index e462c5d..1835956 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -948,6 +948,8 @@ source "arch/arm/mach-ks8695/Kconfig"
source "arch/arm/mach-msm/Kconfig"
+source "arch/arm/mach-moxart/Kconfig"
+
source "arch/arm/mach-mv78xx0/Kconfig"
source "arch/arm/mach-imx/Kconfig"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index aa791d1..35ff8aa 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -167,6 +167,7 @@ machine-$(CONFIG_ARCH_KIRKWOOD) += kirkwood
machine-$(CONFIG_ARCH_KS8695) += ks8695
machine-$(CONFIG_ARCH_LPC32XX) += lpc32xx
machine-$(CONFIG_ARCH_MMP) += mmp
+machine-$(CONFIG_ARCH_MOXART) += moxart
machine-$(CONFIG_ARCH_MSM) += msm
machine-$(CONFIG_ARCH_MV78XX0) += mv78xx0
machine-$(CONFIG_ARCH_MVEBU) += mvebu
diff --git a/arch/arm/configs/moxart_defconfig b/arch/arm/configs/moxart_defconfig
new file mode 100644
index 0000000..a3cb76c
--- /dev/null
+++ b/arch/arm/configs/moxart_defconfig
@@ -0,0 +1,149 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_SYSCTL_SYSCALL=y
+# CONFIG_ELF_CORE is not set
+# CONFIG_BASE_FULL is not set
+# CONFIG_SIGNALFD is not set
+# CONFIG_TIMERFD is not set
+# CONFIG_EVENTFD is not set
+# CONFIG_AIO is not set
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_SLUB_DEBUG is not set
+# CONFIG_COMPAT_BRK is not set
+# CONFIG_LBDAF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_ARCH_MULTI_V4T=y
+# CONFIG_ARCH_MULTI_V7 is not set
+CONFIG_KEYBOARD_GPIO_POLLED=y
+CONFIG_ARCH_MOXART=y
+CONFIG_MACH_UC7112LX=y
+CONFIG_PREEMPT=y
+CONFIG_AEABI=y
+# CONFIG_ATAGS is not set
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+# CONFIG_FW_LOADER is not set
+CONFIG_MTD=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_GEOMETRY=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_PROC_DEVICETREE=y
+CONFIG_NETDEVICES=y
+CONFIG_NETCONSOLE=y
+CONFIG_NETCONSOLE_DYNAMIC=y
+# CONFIG_NET_VENDOR_ARC is not set
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+CONFIG_ARM_MOXART_ETHER=y
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_REALTEK_PHY=y
+CONFIG_MDIO_MOXART=y
+# CONFIG_WLAN is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_INPUT_EVDEV=y
+CONFIG_INPUT_EVBUG=y
+# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=1
+CONFIG_SERIAL_8250_RUNTIME_UARTS=1
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_DEBUG_GPIO=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_MOXART=y
+CONFIG_POWER_SUPPLY=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_GPIO=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_WATCHDOG_CORE=y
+CONFIG_WATCHDOG_NOWAYOUT=y
+CONFIG_MOXART_WDT=y
+# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI_MOXART=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_ONESHOT=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_MOXART=y
+CONFIG_DMADEVICES=y
+CONFIG_MOXART_DMA=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT3_FS=y
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_JFFS2_FS=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+# CONFIG_ENABLE_MUST_CHECK is not set
+CONFIG_DEBUG_PAGEALLOC=y
+CONFIG_DEBUG_OBJECTS=y
+CONFIG_DEBUG_KMEMLEAK=y
+CONFIG_DEBUG_STACK_USAGE=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_DEBUG_SHIRQ=y
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_PROVE_LOCKING=y
+CONFIG_DMA_API_DEBUG=y
+CONFIG_KGDB=y
+CONFIG_DEBUG_LL=y
+CONFIG_DEBUG_LL_UART_8250=y
+CONFIG_DEBUG_UART_PHYS=0x98200000
+CONFIG_DEBUG_UART_VIRT=0xf9820000
+CONFIG_EARLY_PRINTK=y
+CONFIG_KEYS=y
+CONFIG_CRC32_BIT=y
diff --git a/arch/arm/mach-moxart/Kconfig b/arch/arm/mach-moxart/Kconfig
new file mode 100644
index 0000000..ba470d6
--- /dev/null
+++ b/arch/arm/mach-moxart/Kconfig
@@ -0,0 +1,31 @@
+config ARCH_MOXART
+ bool "MOXA ART SoC" if ARCH_MULTI_V4T
+ select CPU_FA526
+ select ARM_DMA_MEM_BUFFERABLE
+ select DMA_OF
+ select USE_OF
+ select CLKSRC_OF
+ select CLKSRC_MMIO
+ select HAVE_CLK
+ select COMMON_CLK
+ select GENERIC_IRQ_CHIP
+ select ARCH_REQUIRE_GPIOLIB
+ select GENERIC_CLOCKEVENTS
+ select PHYLIB if NETDEVICES
+ help
+ Say Y here if you want to run your kernel on hardware with a
+ MOXA ART SoC.
+ The MOXA ART SoC is based on a Faraday FA526 ARMv4 32-bit
+ 192 MHz CPU with MMU and 16KB/8KB D/I-cache (UC-7112-LX).
+ Used on models UC-7101, UC-7112/UC-7110, IA240/IA241, IA3341.
+
+if ARCH_MOXART
+
+config MACH_UC7112LX
+ bool "MOXA UC-7112-LX"
+ depends on ARCH_MOXART
+ help
+ Say Y here if you intend to run this kernel on a MOXA
+ UC-7112-LX embedded computer.
+
+endif
diff --git a/arch/arm/mach-moxart/Makefile b/arch/arm/mach-moxart/Makefile
new file mode 100644
index 0000000..fa022eb
--- /dev/null
+++ b/arch/arm/mach-moxart/Makefile
@@ -0,0 +1,3 @@
+# Object file lists.
+
+obj-$(CONFIG_MACH_UC7112LX) += moxart.o
diff --git a/arch/arm/mach-moxart/moxart.c b/arch/arm/mach-moxart/moxart.c
new file mode 100644
index 0000000..86b6d9b
--- /dev/null
+++ b/arch/arm/mach-moxart/moxart.c
@@ -0,0 +1,15 @@
+/*
+ * arch/arm/mach-moxart/moxart.c
+ *
+ * (C) Copyright 2013, Jonas Jensen <jonas.jensen@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
--
1.8.2.1
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v5 1/2] ARM: mach-moxart: add MOXA ART SoC platform files
@ 2013-12-17 15:38 ` Jonas Jensen
0 siblings, 0 replies; 16+ messages in thread
From: Jonas Jensen @ 2013-12-17 15:38 UTC (permalink / raw)
To: linux-arm-kernel
The MOXA ART SoC is based on Faraday's FA526. This is a ARMv4 32-bit
192 MHz CPU with MMU and 16KB/8KB D/I-cache.
Add platform support for this SoC.
Also add UC-7112-LX as a machine.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
---
arch/arm/Kconfig | 2 +
arch/arm/Makefile | 1 +
arch/arm/configs/moxart_defconfig | 149 ++++++++++++++++++++++++++++++++++++++
arch/arm/mach-moxart/Kconfig | 31 ++++++++
arch/arm/mach-moxart/Makefile | 3 +
arch/arm/mach-moxart/moxart.c | 15 ++++
6 files changed, 201 insertions(+)
create mode 100644 arch/arm/configs/moxart_defconfig
create mode 100644 arch/arm/mach-moxart/Kconfig
create mode 100644 arch/arm/mach-moxart/Makefile
create mode 100644 arch/arm/mach-moxart/moxart.c
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index e462c5d..1835956 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -948,6 +948,8 @@ source "arch/arm/mach-ks8695/Kconfig"
source "arch/arm/mach-msm/Kconfig"
+source "arch/arm/mach-moxart/Kconfig"
+
source "arch/arm/mach-mv78xx0/Kconfig"
source "arch/arm/mach-imx/Kconfig"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index aa791d1..35ff8aa 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -167,6 +167,7 @@ machine-$(CONFIG_ARCH_KIRKWOOD) += kirkwood
machine-$(CONFIG_ARCH_KS8695) += ks8695
machine-$(CONFIG_ARCH_LPC32XX) += lpc32xx
machine-$(CONFIG_ARCH_MMP) += mmp
+machine-$(CONFIG_ARCH_MOXART) += moxart
machine-$(CONFIG_ARCH_MSM) += msm
machine-$(CONFIG_ARCH_MV78XX0) += mv78xx0
machine-$(CONFIG_ARCH_MVEBU) += mvebu
diff --git a/arch/arm/configs/moxart_defconfig b/arch/arm/configs/moxart_defconfig
new file mode 100644
index 0000000..a3cb76c
--- /dev/null
+++ b/arch/arm/configs/moxart_defconfig
@@ -0,0 +1,149 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_SYSCTL_SYSCALL=y
+# CONFIG_ELF_CORE is not set
+# CONFIG_BASE_FULL is not set
+# CONFIG_SIGNALFD is not set
+# CONFIG_TIMERFD is not set
+# CONFIG_EVENTFD is not set
+# CONFIG_AIO is not set
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_SLUB_DEBUG is not set
+# CONFIG_COMPAT_BRK is not set
+# CONFIG_LBDAF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_ARCH_MULTI_V4T=y
+# CONFIG_ARCH_MULTI_V7 is not set
+CONFIG_KEYBOARD_GPIO_POLLED=y
+CONFIG_ARCH_MOXART=y
+CONFIG_MACH_UC7112LX=y
+CONFIG_PREEMPT=y
+CONFIG_AEABI=y
+# CONFIG_ATAGS is not set
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+# CONFIG_FW_LOADER is not set
+CONFIG_MTD=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_GEOMETRY=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_PROC_DEVICETREE=y
+CONFIG_NETDEVICES=y
+CONFIG_NETCONSOLE=y
+CONFIG_NETCONSOLE_DYNAMIC=y
+# CONFIG_NET_VENDOR_ARC is not set
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+CONFIG_ARM_MOXART_ETHER=y
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_REALTEK_PHY=y
+CONFIG_MDIO_MOXART=y
+# CONFIG_WLAN is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_INPUT_EVDEV=y
+CONFIG_INPUT_EVBUG=y
+# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=1
+CONFIG_SERIAL_8250_RUNTIME_UARTS=1
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_DEBUG_GPIO=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_MOXART=y
+CONFIG_POWER_SUPPLY=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_GPIO=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_WATCHDOG_CORE=y
+CONFIG_WATCHDOG_NOWAYOUT=y
+CONFIG_MOXART_WDT=y
+# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI_MOXART=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_ONESHOT=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_MOXART=y
+CONFIG_DMADEVICES=y
+CONFIG_MOXART_DMA=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT3_FS=y
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_JFFS2_FS=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+# CONFIG_ENABLE_MUST_CHECK is not set
+CONFIG_DEBUG_PAGEALLOC=y
+CONFIG_DEBUG_OBJECTS=y
+CONFIG_DEBUG_KMEMLEAK=y
+CONFIG_DEBUG_STACK_USAGE=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_DEBUG_SHIRQ=y
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_PROVE_LOCKING=y
+CONFIG_DMA_API_DEBUG=y
+CONFIG_KGDB=y
+CONFIG_DEBUG_LL=y
+CONFIG_DEBUG_LL_UART_8250=y
+CONFIG_DEBUG_UART_PHYS=0x98200000
+CONFIG_DEBUG_UART_VIRT=0xf9820000
+CONFIG_EARLY_PRINTK=y
+CONFIG_KEYS=y
+CONFIG_CRC32_BIT=y
diff --git a/arch/arm/mach-moxart/Kconfig b/arch/arm/mach-moxart/Kconfig
new file mode 100644
index 0000000..ba470d6
--- /dev/null
+++ b/arch/arm/mach-moxart/Kconfig
@@ -0,0 +1,31 @@
+config ARCH_MOXART
+ bool "MOXA ART SoC" if ARCH_MULTI_V4T
+ select CPU_FA526
+ select ARM_DMA_MEM_BUFFERABLE
+ select DMA_OF
+ select USE_OF
+ select CLKSRC_OF
+ select CLKSRC_MMIO
+ select HAVE_CLK
+ select COMMON_CLK
+ select GENERIC_IRQ_CHIP
+ select ARCH_REQUIRE_GPIOLIB
+ select GENERIC_CLOCKEVENTS
+ select PHYLIB if NETDEVICES
+ help
+ Say Y here if you want to run your kernel on hardware with a
+ MOXA ART SoC.
+ The MOXA ART SoC is based on a Faraday FA526 ARMv4 32-bit
+ 192 MHz CPU with MMU and 16KB/8KB D/I-cache (UC-7112-LX).
+ Used on models UC-7101, UC-7112/UC-7110, IA240/IA241, IA3341.
+
+if ARCH_MOXART
+
+config MACH_UC7112LX
+ bool "MOXA UC-7112-LX"
+ depends on ARCH_MOXART
+ help
+ Say Y here if you intend to run this kernel on a MOXA
+ UC-7112-LX embedded computer.
+
+endif
diff --git a/arch/arm/mach-moxart/Makefile b/arch/arm/mach-moxart/Makefile
new file mode 100644
index 0000000..fa022eb
--- /dev/null
+++ b/arch/arm/mach-moxart/Makefile
@@ -0,0 +1,3 @@
+# Object file lists.
+
+obj-$(CONFIG_MACH_UC7112LX) += moxart.o
diff --git a/arch/arm/mach-moxart/moxart.c b/arch/arm/mach-moxart/moxart.c
new file mode 100644
index 0000000..86b6d9b
--- /dev/null
+++ b/arch/arm/mach-moxart/moxart.c
@@ -0,0 +1,15 @@
+/*
+ * arch/arm/mach-moxart/moxart.c
+ *
+ * (C) Copyright 2013, Jonas Jensen <jonas.jensen@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
--
1.8.2.1
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v5 2/2] ARM: mach-moxart: add MOXA ART SoC device tree files
2013-12-17 15:38 ` Jonas Jensen
@ 2013-12-17 15:38 ` Jonas Jensen
-1 siblings, 0 replies; 16+ messages in thread
From: Jonas Jensen @ 2013-12-17 15:38 UTC (permalink / raw)
To: linux-arm-kernel
Cc: linux-kernel, devicetree, arm, linux, arnd, olof,
soren.brinkmann, peter.crosthwaite, linux, Jonas Jensen
Add a generic (dtsi) include file for MOXA ART SoCs.
Also add a file for UC-7112-LX.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
---
Documentation/devicetree/bindings/arm/moxart.txt | 12 ++
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/moxart-uc7112lx.dts | 93 +++++++++++++
arch/arm/boot/dts/moxart.dtsi | 167 +++++++++++++++++++++++
4 files changed, 273 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/moxart.txt
create mode 100644 arch/arm/boot/dts/moxart-uc7112lx.dts
create mode 100644 arch/arm/boot/dts/moxart.dtsi
diff --git a/Documentation/devicetree/bindings/arm/moxart.txt b/Documentation/devicetree/bindings/arm/moxart.txt
new file mode 100644
index 0000000..11087ed
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/moxart.txt
@@ -0,0 +1,12 @@
+MOXA ART device tree bindings
+
+Boards with the MOXA ART SoC shall have the following properties:
+
+Required root node property:
+
+compatible = "moxa,moxart";
+
+Boards:
+
+- UC-7112-LX: embedded computer
+ compatible = "moxa,moxart-uc-7112-lx", "moxa,moxart"
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index c55a22d..ae3d7db 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -319,6 +319,7 @@ dtb-$(CONFIG_ARCH_VT8500) += vt8500-bv07.dtb \
dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
zynq-zc706.dtb \
zynq-zed.dtb
+dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb
targets += dtbs
targets += $(dtb-y)
diff --git a/arch/arm/boot/dts/moxart-uc7112lx.dts b/arch/arm/boot/dts/moxart-uc7112lx.dts
new file mode 100644
index 0000000..0e037c1
--- /dev/null
+++ b/arch/arm/boot/dts/moxart-uc7112lx.dts
@@ -0,0 +1,93 @@
+/* moxart-uc7112lx.dts - Device Tree file for MOXA UC-7112-LX
+ *
+ * Copyright (C) 2013 Jonas Jensen <jonas.jensen@gmail.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/dts-v1/;
+/include/ "moxart.dtsi"
+
+/ {
+ model = "MOXA UC-7112-LX";
+ compatible = "moxa,moxart-uc-7112-lx", "moxa,moxart";
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x2000000>;
+ };
+
+ flash@80000000,0 {
+ compatible = "numonyx,js28f128", "cfi-flash";
+ reg = <0x80000000 0x1000000>;
+ bank-width = <2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@0 {
+ label = "bootloader";
+ reg = <0x0 0x40000>;
+ };
+ partition@40000 {
+ label = "linux kernel";
+ reg = <0x40000 0x1C0000>;
+ };
+ partition@200000 {
+ label = "root filesystem";
+ reg = <0x200000 0x800000>;
+ };
+ partition@a00000 {
+ label = "user filesystem";
+ reg = <0xa00000 0x600000>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ user-led {
+ label = "ready-led";
+ gpios = <&gpio 27 0x1>;
+ default-state = "on";
+ linux,default-trigger = "default-on";
+ };
+ };
+
+ gpio_keys_polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <500>;
+ button@25 {
+ label = "GPIO Reset";
+ linux,code = <116>;
+ gpios = <&gpio 25 1>;
+ };
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/mmcblk0p1 rw rootwait";
+ };
+};
+
+&sdhci {
+ status = "okay";
+};
+
+&mdio0 {
+ status = "okay";
+};
+
+&mdio1 {
+ status = "okay";
+};
+
+&mac0 {
+ status = "okay";
+};
+
+&mac1 {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/moxart.dtsi b/arch/arm/boot/dts/moxart.dtsi
new file mode 100644
index 0000000..76114e0
--- /dev/null
+++ b/arch/arm/boot/dts/moxart.dtsi
@@ -0,0 +1,167 @@
+/* moxart.dtsi - Device Tree Include file for MOXA ART family SoC
+ *
+ * Copyright (C) 2013 Jonas Jensen <jonas.jensen@gmail.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+ compatible = "moxa,moxart";
+ model = "MOXART";
+ interrupt-parent = <&intc>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "faraday,fa526";
+ reg = <0>;
+ };
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ref12: ref12M {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <12000000>;
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x90000000 0x10000000>;
+ ranges;
+
+ intc: interrupt-controller@98800000 {
+ compatible = "moxa,moxart-ic";
+ reg = <0x98800000 0x38>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-mask = <0x00080000>;
+ };
+
+ clk_pll: clk_pll@98100000 {
+ compatible = "moxa,moxart-pll-clock";
+ #clock-cells = <0>;
+ reg = <0x98100000 0x34>;
+ clocks = <&ref12>;
+ };
+
+ clk_apb: clk_apb@98100000 {
+ compatible = "moxa,moxart-apb-clock";
+ #clock-cells = <0>;
+ reg = <0x98100000 0x34>;
+ clocks = <&clk_pll>;
+ };
+
+ timer: timer@98400000 {
+ compatible = "moxa,moxart-timer";
+ reg = <0x98400000 0x42>;
+ interrupts = <19 1>;
+ clocks = <&clk_apb>;
+ };
+
+ gpio: gpio@98700000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ compatible = "moxa,moxart-gpio";
+ reg = <0x98700000 0xC>;
+ };
+
+ rtc: rtc {
+ compatible = "moxa,moxart-rtc";
+ gpio-rtc-sclk = <&gpio 5 0>;
+ gpio-rtc-data = <&gpio 6 0>;
+ gpio-rtc-reset = <&gpio 7 0>;
+ };
+
+ dma: dma@90500000 {
+ compatible = "moxa,moxart-dma";
+ reg = <0x90500080 0x40>;
+ interrupts = <24 0>;
+ #dma-cells = <1>;
+ };
+
+ watchdog: watchdog@98500000 {
+ compatible = "moxa,moxart-watchdog";
+ reg = <0x98500000 0x10>;
+ clocks = <&clk_apb>;
+ };
+
+ sdhci: sdhci@98e00000 {
+ compatible = "moxa,moxart-sdhci";
+ reg = <0x98e00000 0x5C>;
+ interrupts = <5 0>;
+ clocks = <&clk_apb>;
+ dmas = <&dma 5>,
+ <&dma 5>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ mdio0: mdio@90900090 {
+ compatible = "moxa,moxart-mdio";
+ reg = <0x90900090 0x8>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ ethphy0: ethernet-phy@1 {
+ device_type = "ethernet-phy";
+ compatible = "moxa,moxart-rtl8201cp", "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+ };
+
+ mdio1: mdio@92000090 {
+ compatible = "moxa,moxart-mdio";
+ reg = <0x92000090 0x8>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ ethphy1: ethernet-phy@1 {
+ device_type = "ethernet-phy";
+ compatible = "moxa,moxart-rtl8201cp", "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+ };
+
+ mac0: mac@90900000 {
+ compatible = "moxa,moxart-mac";
+ reg = <0x90900000 0x90>;
+ interrupts = <25 0>;
+ phy-handle = <ðphy0>;
+ phy-mode = "mii";
+ status = "disabled";
+ };
+
+ mac1: mac@92000000 {
+ compatible = "moxa,moxart-mac";
+ reg = <0x92000000 0x90>;
+ interrupts = <27 0>;
+ phy-handle = <ðphy1>;
+ phy-mode = "mii";
+ status = "disabled";
+ };
+
+ uart0: uart@98200000 {
+ compatible = "ns16550a";
+ reg = <0x98200000 0x20>;
+ interrupts = <31 8>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clock-frequency = <14745600>;
+ status = "disabled";
+ };
+ };
+};
--
1.8.2.1
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v5 2/2] ARM: mach-moxart: add MOXA ART SoC device tree files
@ 2013-12-17 15:38 ` Jonas Jensen
0 siblings, 0 replies; 16+ messages in thread
From: Jonas Jensen @ 2013-12-17 15:38 UTC (permalink / raw)
To: linux-arm-kernel
Add a generic (dtsi) include file for MOXA ART SoCs.
Also add a file for UC-7112-LX.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
---
Documentation/devicetree/bindings/arm/moxart.txt | 12 ++
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/moxart-uc7112lx.dts | 93 +++++++++++++
arch/arm/boot/dts/moxart.dtsi | 167 +++++++++++++++++++++++
4 files changed, 273 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/moxart.txt
create mode 100644 arch/arm/boot/dts/moxart-uc7112lx.dts
create mode 100644 arch/arm/boot/dts/moxart.dtsi
diff --git a/Documentation/devicetree/bindings/arm/moxart.txt b/Documentation/devicetree/bindings/arm/moxart.txt
new file mode 100644
index 0000000..11087ed
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/moxart.txt
@@ -0,0 +1,12 @@
+MOXA ART device tree bindings
+
+Boards with the MOXA ART SoC shall have the following properties:
+
+Required root node property:
+
+compatible = "moxa,moxart";
+
+Boards:
+
+- UC-7112-LX: embedded computer
+ compatible = "moxa,moxart-uc-7112-lx", "moxa,moxart"
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index c55a22d..ae3d7db 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -319,6 +319,7 @@ dtb-$(CONFIG_ARCH_VT8500) += vt8500-bv07.dtb \
dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
zynq-zc706.dtb \
zynq-zed.dtb
+dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb
targets += dtbs
targets += $(dtb-y)
diff --git a/arch/arm/boot/dts/moxart-uc7112lx.dts b/arch/arm/boot/dts/moxart-uc7112lx.dts
new file mode 100644
index 0000000..0e037c1
--- /dev/null
+++ b/arch/arm/boot/dts/moxart-uc7112lx.dts
@@ -0,0 +1,93 @@
+/* moxart-uc7112lx.dts - Device Tree file for MOXA UC-7112-LX
+ *
+ * Copyright (C) 2013 Jonas Jensen <jonas.jensen@gmail.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/dts-v1/;
+/include/ "moxart.dtsi"
+
+/ {
+ model = "MOXA UC-7112-LX";
+ compatible = "moxa,moxart-uc-7112-lx", "moxa,moxart";
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x2000000>;
+ };
+
+ flash at 80000000,0 {
+ compatible = "numonyx,js28f128", "cfi-flash";
+ reg = <0x80000000 0x1000000>;
+ bank-width = <2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition at 0 {
+ label = "bootloader";
+ reg = <0x0 0x40000>;
+ };
+ partition at 40000 {
+ label = "linux kernel";
+ reg = <0x40000 0x1C0000>;
+ };
+ partition at 200000 {
+ label = "root filesystem";
+ reg = <0x200000 0x800000>;
+ };
+ partition at a00000 {
+ label = "user filesystem";
+ reg = <0xa00000 0x600000>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ user-led {
+ label = "ready-led";
+ gpios = <&gpio 27 0x1>;
+ default-state = "on";
+ linux,default-trigger = "default-on";
+ };
+ };
+
+ gpio_keys_polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <500>;
+ button at 25 {
+ label = "GPIO Reset";
+ linux,code = <116>;
+ gpios = <&gpio 25 1>;
+ };
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/mmcblk0p1 rw rootwait";
+ };
+};
+
+&sdhci {
+ status = "okay";
+};
+
+&mdio0 {
+ status = "okay";
+};
+
+&mdio1 {
+ status = "okay";
+};
+
+&mac0 {
+ status = "okay";
+};
+
+&mac1 {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/moxart.dtsi b/arch/arm/boot/dts/moxart.dtsi
new file mode 100644
index 0000000..76114e0
--- /dev/null
+++ b/arch/arm/boot/dts/moxart.dtsi
@@ -0,0 +1,167 @@
+/* moxart.dtsi - Device Tree Include file for MOXA ART family SoC
+ *
+ * Copyright (C) 2013 Jonas Jensen <jonas.jensen@gmail.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+ compatible = "moxa,moxart";
+ model = "MOXART";
+ interrupt-parent = <&intc>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ device_type = "cpu";
+ compatible = "faraday,fa526";
+ reg = <0>;
+ };
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ref12: ref12M {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <12000000>;
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x90000000 0x10000000>;
+ ranges;
+
+ intc: interrupt-controller at 98800000 {
+ compatible = "moxa,moxart-ic";
+ reg = <0x98800000 0x38>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-mask = <0x00080000>;
+ };
+
+ clk_pll: clk_pll at 98100000 {
+ compatible = "moxa,moxart-pll-clock";
+ #clock-cells = <0>;
+ reg = <0x98100000 0x34>;
+ clocks = <&ref12>;
+ };
+
+ clk_apb: clk_apb at 98100000 {
+ compatible = "moxa,moxart-apb-clock";
+ #clock-cells = <0>;
+ reg = <0x98100000 0x34>;
+ clocks = <&clk_pll>;
+ };
+
+ timer: timer at 98400000 {
+ compatible = "moxa,moxart-timer";
+ reg = <0x98400000 0x42>;
+ interrupts = <19 1>;
+ clocks = <&clk_apb>;
+ };
+
+ gpio: gpio at 98700000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ compatible = "moxa,moxart-gpio";
+ reg = <0x98700000 0xC>;
+ };
+
+ rtc: rtc {
+ compatible = "moxa,moxart-rtc";
+ gpio-rtc-sclk = <&gpio 5 0>;
+ gpio-rtc-data = <&gpio 6 0>;
+ gpio-rtc-reset = <&gpio 7 0>;
+ };
+
+ dma: dma at 90500000 {
+ compatible = "moxa,moxart-dma";
+ reg = <0x90500080 0x40>;
+ interrupts = <24 0>;
+ #dma-cells = <1>;
+ };
+
+ watchdog: watchdog at 98500000 {
+ compatible = "moxa,moxart-watchdog";
+ reg = <0x98500000 0x10>;
+ clocks = <&clk_apb>;
+ };
+
+ sdhci: sdhci at 98e00000 {
+ compatible = "moxa,moxart-sdhci";
+ reg = <0x98e00000 0x5C>;
+ interrupts = <5 0>;
+ clocks = <&clk_apb>;
+ dmas = <&dma 5>,
+ <&dma 5>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ mdio0: mdio at 90900090 {
+ compatible = "moxa,moxart-mdio";
+ reg = <0x90900090 0x8>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ ethphy0: ethernet-phy at 1 {
+ device_type = "ethernet-phy";
+ compatible = "moxa,moxart-rtl8201cp", "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+ };
+
+ mdio1: mdio at 92000090 {
+ compatible = "moxa,moxart-mdio";
+ reg = <0x92000090 0x8>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ ethphy1: ethernet-phy at 1 {
+ device_type = "ethernet-phy";
+ compatible = "moxa,moxart-rtl8201cp", "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+ };
+
+ mac0: mac at 90900000 {
+ compatible = "moxa,moxart-mac";
+ reg = <0x90900000 0x90>;
+ interrupts = <25 0>;
+ phy-handle = <ðphy0>;
+ phy-mode = "mii";
+ status = "disabled";
+ };
+
+ mac1: mac at 92000000 {
+ compatible = "moxa,moxart-mac";
+ reg = <0x92000000 0x90>;
+ interrupts = <27 0>;
+ phy-handle = <ðphy1>;
+ phy-mode = "mii";
+ status = "disabled";
+ };
+
+ uart0: uart at 98200000 {
+ compatible = "ns16550a";
+ reg = <0x98200000 0x20>;
+ interrupts = <31 8>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clock-frequency = <14745600>;
+ status = "disabled";
+ };
+ };
+};
--
1.8.2.1
^ permalink raw reply related [flat|nested] 16+ messages in thread
* Re: [PATCH v5 2/2] ARM: mach-moxart: add MOXA ART SoC device tree files
2013-12-17 15:38 ` Jonas Jensen
(?)
@ 2013-12-17 23:29 ` Peter Crosthwaite
-1 siblings, 0 replies; 16+ messages in thread
From: Peter Crosthwaite @ 2013-12-17 23:29 UTC (permalink / raw)
To: Jonas Jensen
Cc: linux-arm-kernel, linux-kernel, devicetree, arm,
Russell King - ARM Linux, Arnd Bergmann, Olof Johansson,
Soren Brinkmann, linux
On Wed, Dec 18, 2013 at 1:38 AM, Jonas Jensen <jonas.jensen@gmail.com> wrote:
> Add a generic (dtsi) include file for MOXA ART SoCs.
>
> Also add a file for UC-7112-LX.
>
> Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
> ---
> Documentation/devicetree/bindings/arm/moxart.txt | 12 ++
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/moxart-uc7112lx.dts | 93 +++++++++++++
> arch/arm/boot/dts/moxart.dtsi | 167 +++++++++++++++++++++++
> 4 files changed, 273 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/moxart.txt
> create mode 100644 arch/arm/boot/dts/moxart-uc7112lx.dts
> create mode 100644 arch/arm/boot/dts/moxart.dtsi
>
> diff --git a/Documentation/devicetree/bindings/arm/moxart.txt b/Documentation/devicetree/bindings/arm/moxart.txt
> new file mode 100644
> index 0000000..11087ed
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/moxart.txt
> @@ -0,0 +1,12 @@
> +MOXA ART device tree bindings
> +
> +Boards with the MOXA ART SoC shall have the following properties:
> +
> +Required root node property:
> +
> +compatible = "moxa,moxart";
> +
> +Boards:
> +
> +- UC-7112-LX: embedded computer
> + compatible = "moxa,moxart-uc-7112-lx", "moxa,moxart"
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index c55a22d..ae3d7db 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -319,6 +319,7 @@ dtb-$(CONFIG_ARCH_VT8500) += vt8500-bv07.dtb \
> dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
> zynq-zc706.dtb \
> zynq-zed.dtb
> +dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb
>
> targets += dtbs
> targets += $(dtb-y)
> diff --git a/arch/arm/boot/dts/moxart-uc7112lx.dts b/arch/arm/boot/dts/moxart-uc7112lx.dts
> new file mode 100644
> index 0000000..0e037c1
> --- /dev/null
> +++ b/arch/arm/boot/dts/moxart-uc7112lx.dts
> @@ -0,0 +1,93 @@
> +/* moxart-uc7112lx.dts - Device Tree file for MOXA UC-7112-LX
> + *
> + * Copyright (C) 2013 Jonas Jensen <jonas.jensen@gmail.com>
> + *
> + * Licensed under GPLv2 or later.
> + */
> +
> +/dts-v1/;
> +/include/ "moxart.dtsi"
> +
> +/ {
> + model = "MOXA UC-7112-LX";
> + compatible = "moxa,moxart-uc-7112-lx", "moxa,moxart";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x0 0x2000000>;
> + };
> +
> + flash@80000000,0 {
> + compatible = "numonyx,js28f128", "cfi-flash";
> + reg = <0x80000000 0x1000000>;
> + bank-width = <2>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + partition@0 {
> + label = "bootloader";
> + reg = <0x0 0x40000>;
> + };
> + partition@40000 {
> + label = "linux kernel";
> + reg = <0x40000 0x1C0000>;
> + };
> + partition@200000 {
> + label = "root filesystem";
> + reg = <0x200000 0x800000>;
> + };
> + partition@a00000 {
> + label = "user filesystem";
> + reg = <0xa00000 0x600000>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + user-led {
> + label = "ready-led";
> + gpios = <&gpio 27 0x1>;
> + default-state = "on";
> + linux,default-trigger = "default-on";
> + };
> + };
> +
> + gpio_keys_polled {
> + compatible = "gpio-keys-polled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + poll-interval = <500>;
> + button@25 {
> + label = "GPIO Reset";
> + linux,code = <116>;
> + gpios = <&gpio 25 1>;
> + };
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/mmcblk0p1 rw rootwait";
> + };
> +};
> +
> +&sdhci {
> + status = "okay";
> +};
> +
> +&mdio0 {
> + status = "okay";
> +};
> +
> +&mdio1 {
> + status = "okay";
> +};
> +
> +&mac0 {
> + status = "okay";
> +};
> +
> +&mac1 {
> + status = "okay";
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/moxart.dtsi b/arch/arm/boot/dts/moxart.dtsi
> new file mode 100644
> index 0000000..76114e0
> --- /dev/null
> +++ b/arch/arm/boot/dts/moxart.dtsi
> @@ -0,0 +1,167 @@
> +/* moxart.dtsi - Device Tree Include file for MOXA ART family SoC
> + *
> + * Copyright (C) 2013 Jonas Jensen <jonas.jensen@gmail.com>
> + *
> + * Licensed under GPLv2 or later.
> + */
> +
> +/include/ "skeleton.dtsi"
> +
> +/ {
> + compatible = "moxa,moxart";
> + model = "MOXART";
> + interrupt-parent = <&intc>;
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu@0 {
> + device_type = "cpu";
> + compatible = "faraday,fa526";
> + reg = <0>;
> + };
> + };
> +
> + clocks {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ref12: ref12M {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <12000000>;
Crystal board level?
> + };
> + };
> +
> + soc {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0x90000000 0x10000000>;
> + ranges;
> +
> + intc: interrupt-controller@98800000 {
> + compatible = "moxa,moxart-ic";
> + reg = <0x98800000 0x38>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupt-mask = <0x00080000>;
> + };
> +
> + clk_pll: clk_pll@98100000 {
> + compatible = "moxa,moxart-pll-clock";
> + #clock-cells = <0>;
> + reg = <0x98100000 0x34>;
> + clocks = <&ref12>;
> + };
> +
> + clk_apb: clk_apb@98100000 {
> + compatible = "moxa,moxart-apb-clock";
> + #clock-cells = <0>;
> + reg = <0x98100000 0x34>;
> + clocks = <&clk_pll>;
> + };
> +
> + timer: timer@98400000 {
> + compatible = "moxa,moxart-timer";
> + reg = <0x98400000 0x42>;
> + interrupts = <19 1>;
> + clocks = <&clk_apb>;
> + };
> +
> + gpio: gpio@98700000 {
> + gpio-controller;
> + #gpio-cells = <2>;
> + compatible = "moxa,moxart-gpio";
> + reg = <0x98700000 0xC>;
> + };
> +
> + rtc: rtc {
> + compatible = "moxa,moxart-rtc";
> + gpio-rtc-sclk = <&gpio 5 0>;
> + gpio-rtc-data = <&gpio 6 0>;
> + gpio-rtc-reset = <&gpio 7 0>;
> + };
> +
> + dma: dma@90500000 {
> + compatible = "moxa,moxart-dma";
> + reg = <0x90500080 0x40>;
> + interrupts = <24 0>;
> + #dma-cells = <1>;
> + };
> +
> + watchdog: watchdog@98500000 {
> + compatible = "moxa,moxart-watchdog";
> + reg = <0x98500000 0x10>;
> + clocks = <&clk_apb>;
> + };
> +
> + sdhci: sdhci@98e00000 {
> + compatible = "moxa,moxart-sdhci";
> + reg = <0x98e00000 0x5C>;
> + interrupts = <5 0>;
> + clocks = <&clk_apb>;
> + dmas = <&dma 5>,
> + <&dma 5>;
> + dma-names = "tx", "rx";
> + status = "disabled";
> + };
> +
> + mdio0: mdio@90900090 {
> + compatible = "moxa,moxart-mdio";
> + reg = <0x90900090 0x8>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> +
> + ethphy0: ethernet-phy@1 {
> + device_type = "ethernet-phy";
> + compatible = "moxa,moxart-rtl8201cp", "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + };
> + };
> +
> + mdio1: mdio@92000090 {
> + compatible = "moxa,moxart-mdio";
> + reg = <0x92000090 0x8>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> +
> + ethphy1: ethernet-phy@1 {
> + device_type = "ethernet-phy";
> + compatible = "moxa,moxart-rtl8201cp", "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + };
Are the phys board or SoC level?
> + };
> +
> + mac0: mac@90900000 {
> + compatible = "moxa,moxart-mac";
> + reg = <0x90900000 0x90>;
> + interrupts = <25 0>;
> + phy-handle = <ðphy0>;
> + phy-mode = "mii";
If the IP supports multiple PHYs of different external connection
schemes then the phy connectivity should got back to board level. If
not:
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
I don't know much about arm/mach- and Kconfig, so I'll sit out the
review of P1.
Regards,
Peter
> + status = "disabled";
> + };
> +
> + mac1: mac@92000000 {
> + compatible = "moxa,moxart-mac";
> + reg = <0x92000000 0x90>;
> + interrupts = <27 0>;
> + phy-handle = <ðphy1>;
> + phy-mode = "mii";
> + status = "disabled";
> + };
> +
> + uart0: uart@98200000 {
> + compatible = "ns16550a";
> + reg = <0x98200000 0x20>;
> + interrupts = <31 8>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clock-frequency = <14745600>;
> + status = "disabled";
> + };
> + };
> +};
> --
> 1.8.2.1
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v5 2/2] ARM: mach-moxart: add MOXA ART SoC device tree files
@ 2013-12-17 23:29 ` Peter Crosthwaite
0 siblings, 0 replies; 16+ messages in thread
From: Peter Crosthwaite @ 2013-12-17 23:29 UTC (permalink / raw)
To: Jonas Jensen
Cc: linux-arm-kernel, linux-kernel, devicetree, arm,
Russell King - ARM Linux, Arnd Bergmann, Olof Johansson,
Soren Brinkmann, linux
On Wed, Dec 18, 2013 at 1:38 AM, Jonas Jensen <jonas.jensen@gmail.com> wrote:
> Add a generic (dtsi) include file for MOXA ART SoCs.
>
> Also add a file for UC-7112-LX.
>
> Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
> ---
> Documentation/devicetree/bindings/arm/moxart.txt | 12 ++
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/moxart-uc7112lx.dts | 93 +++++++++++++
> arch/arm/boot/dts/moxart.dtsi | 167 +++++++++++++++++++++++
> 4 files changed, 273 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/moxart.txt
> create mode 100644 arch/arm/boot/dts/moxart-uc7112lx.dts
> create mode 100644 arch/arm/boot/dts/moxart.dtsi
>
> diff --git a/Documentation/devicetree/bindings/arm/moxart.txt b/Documentation/devicetree/bindings/arm/moxart.txt
> new file mode 100644
> index 0000000..11087ed
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/moxart.txt
> @@ -0,0 +1,12 @@
> +MOXA ART device tree bindings
> +
> +Boards with the MOXA ART SoC shall have the following properties:
> +
> +Required root node property:
> +
> +compatible = "moxa,moxart";
> +
> +Boards:
> +
> +- UC-7112-LX: embedded computer
> + compatible = "moxa,moxart-uc-7112-lx", "moxa,moxart"
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index c55a22d..ae3d7db 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -319,6 +319,7 @@ dtb-$(CONFIG_ARCH_VT8500) += vt8500-bv07.dtb \
> dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
> zynq-zc706.dtb \
> zynq-zed.dtb
> +dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb
>
> targets += dtbs
> targets += $(dtb-y)
> diff --git a/arch/arm/boot/dts/moxart-uc7112lx.dts b/arch/arm/boot/dts/moxart-uc7112lx.dts
> new file mode 100644
> index 0000000..0e037c1
> --- /dev/null
> +++ b/arch/arm/boot/dts/moxart-uc7112lx.dts
> @@ -0,0 +1,93 @@
> +/* moxart-uc7112lx.dts - Device Tree file for MOXA UC-7112-LX
> + *
> + * Copyright (C) 2013 Jonas Jensen <jonas.jensen@gmail.com>
> + *
> + * Licensed under GPLv2 or later.
> + */
> +
> +/dts-v1/;
> +/include/ "moxart.dtsi"
> +
> +/ {
> + model = "MOXA UC-7112-LX";
> + compatible = "moxa,moxart-uc-7112-lx", "moxa,moxart";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x0 0x2000000>;
> + };
> +
> + flash@80000000,0 {
> + compatible = "numonyx,js28f128", "cfi-flash";
> + reg = <0x80000000 0x1000000>;
> + bank-width = <2>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + partition@0 {
> + label = "bootloader";
> + reg = <0x0 0x40000>;
> + };
> + partition@40000 {
> + label = "linux kernel";
> + reg = <0x40000 0x1C0000>;
> + };
> + partition@200000 {
> + label = "root filesystem";
> + reg = <0x200000 0x800000>;
> + };
> + partition@a00000 {
> + label = "user filesystem";
> + reg = <0xa00000 0x600000>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + user-led {
> + label = "ready-led";
> + gpios = <&gpio 27 0x1>;
> + default-state = "on";
> + linux,default-trigger = "default-on";
> + };
> + };
> +
> + gpio_keys_polled {
> + compatible = "gpio-keys-polled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + poll-interval = <500>;
> + button@25 {
> + label = "GPIO Reset";
> + linux,code = <116>;
> + gpios = <&gpio 25 1>;
> + };
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/mmcblk0p1 rw rootwait";
> + };
> +};
> +
> +&sdhci {
> + status = "okay";
> +};
> +
> +&mdio0 {
> + status = "okay";
> +};
> +
> +&mdio1 {
> + status = "okay";
> +};
> +
> +&mac0 {
> + status = "okay";
> +};
> +
> +&mac1 {
> + status = "okay";
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/moxart.dtsi b/arch/arm/boot/dts/moxart.dtsi
> new file mode 100644
> index 0000000..76114e0
> --- /dev/null
> +++ b/arch/arm/boot/dts/moxart.dtsi
> @@ -0,0 +1,167 @@
> +/* moxart.dtsi - Device Tree Include file for MOXA ART family SoC
> + *
> + * Copyright (C) 2013 Jonas Jensen <jonas.jensen@gmail.com>
> + *
> + * Licensed under GPLv2 or later.
> + */
> +
> +/include/ "skeleton.dtsi"
> +
> +/ {
> + compatible = "moxa,moxart";
> + model = "MOXART";
> + interrupt-parent = <&intc>;
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu@0 {
> + device_type = "cpu";
> + compatible = "faraday,fa526";
> + reg = <0>;
> + };
> + };
> +
> + clocks {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ref12: ref12M {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <12000000>;
Crystal board level?
> + };
> + };
> +
> + soc {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0x90000000 0x10000000>;
> + ranges;
> +
> + intc: interrupt-controller@98800000 {
> + compatible = "moxa,moxart-ic";
> + reg = <0x98800000 0x38>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupt-mask = <0x00080000>;
> + };
> +
> + clk_pll: clk_pll@98100000 {
> + compatible = "moxa,moxart-pll-clock";
> + #clock-cells = <0>;
> + reg = <0x98100000 0x34>;
> + clocks = <&ref12>;
> + };
> +
> + clk_apb: clk_apb@98100000 {
> + compatible = "moxa,moxart-apb-clock";
> + #clock-cells = <0>;
> + reg = <0x98100000 0x34>;
> + clocks = <&clk_pll>;
> + };
> +
> + timer: timer@98400000 {
> + compatible = "moxa,moxart-timer";
> + reg = <0x98400000 0x42>;
> + interrupts = <19 1>;
> + clocks = <&clk_apb>;
> + };
> +
> + gpio: gpio@98700000 {
> + gpio-controller;
> + #gpio-cells = <2>;
> + compatible = "moxa,moxart-gpio";
> + reg = <0x98700000 0xC>;
> + };
> +
> + rtc: rtc {
> + compatible = "moxa,moxart-rtc";
> + gpio-rtc-sclk = <&gpio 5 0>;
> + gpio-rtc-data = <&gpio 6 0>;
> + gpio-rtc-reset = <&gpio 7 0>;
> + };
> +
> + dma: dma@90500000 {
> + compatible = "moxa,moxart-dma";
> + reg = <0x90500080 0x40>;
> + interrupts = <24 0>;
> + #dma-cells = <1>;
> + };
> +
> + watchdog: watchdog@98500000 {
> + compatible = "moxa,moxart-watchdog";
> + reg = <0x98500000 0x10>;
> + clocks = <&clk_apb>;
> + };
> +
> + sdhci: sdhci@98e00000 {
> + compatible = "moxa,moxart-sdhci";
> + reg = <0x98e00000 0x5C>;
> + interrupts = <5 0>;
> + clocks = <&clk_apb>;
> + dmas = <&dma 5>,
> + <&dma 5>;
> + dma-names = "tx", "rx";
> + status = "disabled";
> + };
> +
> + mdio0: mdio@90900090 {
> + compatible = "moxa,moxart-mdio";
> + reg = <0x90900090 0x8>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> +
> + ethphy0: ethernet-phy@1 {
> + device_type = "ethernet-phy";
> + compatible = "moxa,moxart-rtl8201cp", "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + };
> + };
> +
> + mdio1: mdio@92000090 {
> + compatible = "moxa,moxart-mdio";
> + reg = <0x92000090 0x8>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> +
> + ethphy1: ethernet-phy@1 {
> + device_type = "ethernet-phy";
> + compatible = "moxa,moxart-rtl8201cp", "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + };
Are the phys board or SoC level?
> + };
> +
> + mac0: mac@90900000 {
> + compatible = "moxa,moxart-mac";
> + reg = <0x90900000 0x90>;
> + interrupts = <25 0>;
> + phy-handle = <ðphy0>;
> + phy-mode = "mii";
If the IP supports multiple PHYs of different external connection
schemes then the phy connectivity should got back to board level. If
not:
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
I don't know much about arm/mach- and Kconfig, so I'll sit out the
review of P1.
Regards,
Peter
> + status = "disabled";
> + };
> +
> + mac1: mac@92000000 {
> + compatible = "moxa,moxart-mac";
> + reg = <0x92000000 0x90>;
> + interrupts = <27 0>;
> + phy-handle = <ðphy1>;
> + phy-mode = "mii";
> + status = "disabled";
> + };
> +
> + uart0: uart@98200000 {
> + compatible = "ns16550a";
> + reg = <0x98200000 0x20>;
> + interrupts = <31 8>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clock-frequency = <14745600>;
> + status = "disabled";
> + };
> + };
> +};
> --
> 1.8.2.1
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v5 2/2] ARM: mach-moxart: add MOXA ART SoC device tree files
@ 2013-12-17 23:29 ` Peter Crosthwaite
0 siblings, 0 replies; 16+ messages in thread
From: Peter Crosthwaite @ 2013-12-17 23:29 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Dec 18, 2013 at 1:38 AM, Jonas Jensen <jonas.jensen@gmail.com> wrote:
> Add a generic (dtsi) include file for MOXA ART SoCs.
>
> Also add a file for UC-7112-LX.
>
> Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
> ---
> Documentation/devicetree/bindings/arm/moxart.txt | 12 ++
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/moxart-uc7112lx.dts | 93 +++++++++++++
> arch/arm/boot/dts/moxart.dtsi | 167 +++++++++++++++++++++++
> 4 files changed, 273 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/moxart.txt
> create mode 100644 arch/arm/boot/dts/moxart-uc7112lx.dts
> create mode 100644 arch/arm/boot/dts/moxart.dtsi
>
> diff --git a/Documentation/devicetree/bindings/arm/moxart.txt b/Documentation/devicetree/bindings/arm/moxart.txt
> new file mode 100644
> index 0000000..11087ed
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/moxart.txt
> @@ -0,0 +1,12 @@
> +MOXA ART device tree bindings
> +
> +Boards with the MOXA ART SoC shall have the following properties:
> +
> +Required root node property:
> +
> +compatible = "moxa,moxart";
> +
> +Boards:
> +
> +- UC-7112-LX: embedded computer
> + compatible = "moxa,moxart-uc-7112-lx", "moxa,moxart"
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index c55a22d..ae3d7db 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -319,6 +319,7 @@ dtb-$(CONFIG_ARCH_VT8500) += vt8500-bv07.dtb \
> dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
> zynq-zc706.dtb \
> zynq-zed.dtb
> +dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb
>
> targets += dtbs
> targets += $(dtb-y)
> diff --git a/arch/arm/boot/dts/moxart-uc7112lx.dts b/arch/arm/boot/dts/moxart-uc7112lx.dts
> new file mode 100644
> index 0000000..0e037c1
> --- /dev/null
> +++ b/arch/arm/boot/dts/moxart-uc7112lx.dts
> @@ -0,0 +1,93 @@
> +/* moxart-uc7112lx.dts - Device Tree file for MOXA UC-7112-LX
> + *
> + * Copyright (C) 2013 Jonas Jensen <jonas.jensen@gmail.com>
> + *
> + * Licensed under GPLv2 or later.
> + */
> +
> +/dts-v1/;
> +/include/ "moxart.dtsi"
> +
> +/ {
> + model = "MOXA UC-7112-LX";
> + compatible = "moxa,moxart-uc-7112-lx", "moxa,moxart";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x0 0x2000000>;
> + };
> +
> + flash at 80000000,0 {
> + compatible = "numonyx,js28f128", "cfi-flash";
> + reg = <0x80000000 0x1000000>;
> + bank-width = <2>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + partition at 0 {
> + label = "bootloader";
> + reg = <0x0 0x40000>;
> + };
> + partition at 40000 {
> + label = "linux kernel";
> + reg = <0x40000 0x1C0000>;
> + };
> + partition at 200000 {
> + label = "root filesystem";
> + reg = <0x200000 0x800000>;
> + };
> + partition at a00000 {
> + label = "user filesystem";
> + reg = <0xa00000 0x600000>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + user-led {
> + label = "ready-led";
> + gpios = <&gpio 27 0x1>;
> + default-state = "on";
> + linux,default-trigger = "default-on";
> + };
> + };
> +
> + gpio_keys_polled {
> + compatible = "gpio-keys-polled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + poll-interval = <500>;
> + button at 25 {
> + label = "GPIO Reset";
> + linux,code = <116>;
> + gpios = <&gpio 25 1>;
> + };
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/mmcblk0p1 rw rootwait";
> + };
> +};
> +
> +&sdhci {
> + status = "okay";
> +};
> +
> +&mdio0 {
> + status = "okay";
> +};
> +
> +&mdio1 {
> + status = "okay";
> +};
> +
> +&mac0 {
> + status = "okay";
> +};
> +
> +&mac1 {
> + status = "okay";
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/moxart.dtsi b/arch/arm/boot/dts/moxart.dtsi
> new file mode 100644
> index 0000000..76114e0
> --- /dev/null
> +++ b/arch/arm/boot/dts/moxart.dtsi
> @@ -0,0 +1,167 @@
> +/* moxart.dtsi - Device Tree Include file for MOXA ART family SoC
> + *
> + * Copyright (C) 2013 Jonas Jensen <jonas.jensen@gmail.com>
> + *
> + * Licensed under GPLv2 or later.
> + */
> +
> +/include/ "skeleton.dtsi"
> +
> +/ {
> + compatible = "moxa,moxart";
> + model = "MOXART";
> + interrupt-parent = <&intc>;
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu at 0 {
> + device_type = "cpu";
> + compatible = "faraday,fa526";
> + reg = <0>;
> + };
> + };
> +
> + clocks {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ref12: ref12M {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <12000000>;
Crystal board level?
> + };
> + };
> +
> + soc {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0x90000000 0x10000000>;
> + ranges;
> +
> + intc: interrupt-controller at 98800000 {
> + compatible = "moxa,moxart-ic";
> + reg = <0x98800000 0x38>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupt-mask = <0x00080000>;
> + };
> +
> + clk_pll: clk_pll at 98100000 {
> + compatible = "moxa,moxart-pll-clock";
> + #clock-cells = <0>;
> + reg = <0x98100000 0x34>;
> + clocks = <&ref12>;
> + };
> +
> + clk_apb: clk_apb at 98100000 {
> + compatible = "moxa,moxart-apb-clock";
> + #clock-cells = <0>;
> + reg = <0x98100000 0x34>;
> + clocks = <&clk_pll>;
> + };
> +
> + timer: timer at 98400000 {
> + compatible = "moxa,moxart-timer";
> + reg = <0x98400000 0x42>;
> + interrupts = <19 1>;
> + clocks = <&clk_apb>;
> + };
> +
> + gpio: gpio at 98700000 {
> + gpio-controller;
> + #gpio-cells = <2>;
> + compatible = "moxa,moxart-gpio";
> + reg = <0x98700000 0xC>;
> + };
> +
> + rtc: rtc {
> + compatible = "moxa,moxart-rtc";
> + gpio-rtc-sclk = <&gpio 5 0>;
> + gpio-rtc-data = <&gpio 6 0>;
> + gpio-rtc-reset = <&gpio 7 0>;
> + };
> +
> + dma: dma at 90500000 {
> + compatible = "moxa,moxart-dma";
> + reg = <0x90500080 0x40>;
> + interrupts = <24 0>;
> + #dma-cells = <1>;
> + };
> +
> + watchdog: watchdog at 98500000 {
> + compatible = "moxa,moxart-watchdog";
> + reg = <0x98500000 0x10>;
> + clocks = <&clk_apb>;
> + };
> +
> + sdhci: sdhci at 98e00000 {
> + compatible = "moxa,moxart-sdhci";
> + reg = <0x98e00000 0x5C>;
> + interrupts = <5 0>;
> + clocks = <&clk_apb>;
> + dmas = <&dma 5>,
> + <&dma 5>;
> + dma-names = "tx", "rx";
> + status = "disabled";
> + };
> +
> + mdio0: mdio at 90900090 {
> + compatible = "moxa,moxart-mdio";
> + reg = <0x90900090 0x8>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> +
> + ethphy0: ethernet-phy at 1 {
> + device_type = "ethernet-phy";
> + compatible = "moxa,moxart-rtl8201cp", "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + };
> + };
> +
> + mdio1: mdio at 92000090 {
> + compatible = "moxa,moxart-mdio";
> + reg = <0x92000090 0x8>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> +
> + ethphy1: ethernet-phy at 1 {
> + device_type = "ethernet-phy";
> + compatible = "moxa,moxart-rtl8201cp", "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + };
Are the phys board or SoC level?
> + };
> +
> + mac0: mac at 90900000 {
> + compatible = "moxa,moxart-mac";
> + reg = <0x90900000 0x90>;
> + interrupts = <25 0>;
> + phy-handle = <ðphy0>;
> + phy-mode = "mii";
If the IP supports multiple PHYs of different external connection
schemes then the phy connectivity should got back to board level. If
not:
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
I don't know much about arm/mach- and Kconfig, so I'll sit out the
review of P1.
Regards,
Peter
> + status = "disabled";
> + };
> +
> + mac1: mac at 92000000 {
> + compatible = "moxa,moxart-mac";
> + reg = <0x92000000 0x90>;
> + interrupts = <27 0>;
> + phy-handle = <ðphy1>;
> + phy-mode = "mii";
> + status = "disabled";
> + };
> +
> + uart0: uart at 98200000 {
> + compatible = "ns16550a";
> + reg = <0x98200000 0x20>;
> + interrupts = <31 8>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clock-frequency = <14745600>;
> + status = "disabled";
> + };
> + };
> +};
> --
> 1.8.2.1
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v5 2/2] ARM: mach-moxart: add MOXA ART SoC device tree files
2013-12-17 15:38 ` Jonas Jensen
(?)
@ 2013-12-17 23:57 ` Sören Brinkmann
-1 siblings, 0 replies; 16+ messages in thread
From: Sören Brinkmann @ 2013-12-17 23:57 UTC (permalink / raw)
To: Jonas Jensen
Cc: linux-arm-kernel, linux-kernel, devicetree, arm, linux, arnd,
olof, peter.crosthwaite, linux
Hi Jonas,
On Tue, Dec 17, 2013 at 04:38:34PM +0100, Jonas Jensen wrote:
> Add a generic (dtsi) include file for MOXA ART SoCs.
>
> Also add a file for UC-7112-LX.
>
> Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
> ---
> Documentation/devicetree/bindings/arm/moxart.txt | 12 ++
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/moxart-uc7112lx.dts | 93 +++++++++++++
> arch/arm/boot/dts/moxart.dtsi | 167 +++++++++++++++++++++++
> 4 files changed, 273 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/moxart.txt
> create mode 100644 arch/arm/boot/dts/moxart-uc7112lx.dts
> create mode 100644 arch/arm/boot/dts/moxart.dtsi
>
> diff --git a/Documentation/devicetree/bindings/arm/moxart.txt b/Documentation/devicetree/bindings/arm/moxart.txt
> new file mode 100644
> index 0000000..11087ed
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/moxart.txt
> @@ -0,0 +1,12 @@
> +MOXA ART device tree bindings
> +
> +Boards with the MOXA ART SoC shall have the following properties:
> +
> +Required root node property:
> +
> +compatible = "moxa,moxart";
> +
> +Boards:
> +
> +- UC-7112-LX: embedded computer
> + compatible = "moxa,moxart-uc-7112-lx", "moxa,moxart"
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index c55a22d..ae3d7db 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -319,6 +319,7 @@ dtb-$(CONFIG_ARCH_VT8500) += vt8500-bv07.dtb \
> dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
> zynq-zc706.dtb \
> zynq-zed.dtb
> +dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb
I think these targets are sorted alphabetically. You should insert the
MOXART target at the appropriate location a little further up.
Sören
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v5 2/2] ARM: mach-moxart: add MOXA ART SoC device tree files
@ 2013-12-17 23:57 ` Sören Brinkmann
0 siblings, 0 replies; 16+ messages in thread
From: Sören Brinkmann @ 2013-12-17 23:57 UTC (permalink / raw)
To: Jonas Jensen
Cc: linux-arm-kernel, linux-kernel, devicetree, arm, linux, arnd,
olof, peter.crosthwaite, linux
Hi Jonas,
On Tue, Dec 17, 2013 at 04:38:34PM +0100, Jonas Jensen wrote:
> Add a generic (dtsi) include file for MOXA ART SoCs.
>
> Also add a file for UC-7112-LX.
>
> Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
> ---
> Documentation/devicetree/bindings/arm/moxart.txt | 12 ++
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/moxart-uc7112lx.dts | 93 +++++++++++++
> arch/arm/boot/dts/moxart.dtsi | 167 +++++++++++++++++++++++
> 4 files changed, 273 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/moxart.txt
> create mode 100644 arch/arm/boot/dts/moxart-uc7112lx.dts
> create mode 100644 arch/arm/boot/dts/moxart.dtsi
>
> diff --git a/Documentation/devicetree/bindings/arm/moxart.txt b/Documentation/devicetree/bindings/arm/moxart.txt
> new file mode 100644
> index 0000000..11087ed
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/moxart.txt
> @@ -0,0 +1,12 @@
> +MOXA ART device tree bindings
> +
> +Boards with the MOXA ART SoC shall have the following properties:
> +
> +Required root node property:
> +
> +compatible = "moxa,moxart";
> +
> +Boards:
> +
> +- UC-7112-LX: embedded computer
> + compatible = "moxa,moxart-uc-7112-lx", "moxa,moxart"
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index c55a22d..ae3d7db 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -319,6 +319,7 @@ dtb-$(CONFIG_ARCH_VT8500) += vt8500-bv07.dtb \
> dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
> zynq-zc706.dtb \
> zynq-zed.dtb
> +dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb
I think these targets are sorted alphabetically. You should insert the
MOXART target at the appropriate location a little further up.
Sören
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v5 2/2] ARM: mach-moxart: add MOXA ART SoC device tree files
@ 2013-12-17 23:57 ` Sören Brinkmann
0 siblings, 0 replies; 16+ messages in thread
From: Sören Brinkmann @ 2013-12-17 23:57 UTC (permalink / raw)
To: linux-arm-kernel
Hi Jonas,
On Tue, Dec 17, 2013 at 04:38:34PM +0100, Jonas Jensen wrote:
> Add a generic (dtsi) include file for MOXA ART SoCs.
>
> Also add a file for UC-7112-LX.
>
> Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
> ---
> Documentation/devicetree/bindings/arm/moxart.txt | 12 ++
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/moxart-uc7112lx.dts | 93 +++++++++++++
> arch/arm/boot/dts/moxart.dtsi | 167 +++++++++++++++++++++++
> 4 files changed, 273 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/moxart.txt
> create mode 100644 arch/arm/boot/dts/moxart-uc7112lx.dts
> create mode 100644 arch/arm/boot/dts/moxart.dtsi
>
> diff --git a/Documentation/devicetree/bindings/arm/moxart.txt b/Documentation/devicetree/bindings/arm/moxart.txt
> new file mode 100644
> index 0000000..11087ed
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/moxart.txt
> @@ -0,0 +1,12 @@
> +MOXA ART device tree bindings
> +
> +Boards with the MOXA ART SoC shall have the following properties:
> +
> +Required root node property:
> +
> +compatible = "moxa,moxart";
> +
> +Boards:
> +
> +- UC-7112-LX: embedded computer
> + compatible = "moxa,moxart-uc-7112-lx", "moxa,moxart"
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index c55a22d..ae3d7db 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -319,6 +319,7 @@ dtb-$(CONFIG_ARCH_VT8500) += vt8500-bv07.dtb \
> dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
> zynq-zc706.dtb \
> zynq-zed.dtb
> +dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb
I think these targets are sorted alphabetically. You should insert the
MOXART target at the appropriate location a little further up.
S?ren
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v5 2/2] ARM: mach-moxart: add MOXA ART SoC device tree files
@ 2013-12-18 13:10 ` Jonas Jensen
0 siblings, 0 replies; 16+ messages in thread
From: Jonas Jensen @ 2013-12-18 13:10 UTC (permalink / raw)
To: Peter Crosthwaite, Soren Brinkmann
Cc: linux-arm-kernel, linux-kernel, devicetree, arm,
Russell King - ARM Linux, Arnd Bergmann, Olof Johansson, linux
Thanks for the replies, changes should be in v6.
On 18 December 2013 00:29, Peter Crosthwaite
<peter.crosthwaite@xilinx.com> wrote:
>> + clocks {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + ref12: ref12M {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <12000000>;
>
> Crystal board level?
I couldn't move this due to fixed-clock load order.
See my comments in v6 cover letter:
http://lists.infradead.org/pipermail/linux-arm-kernel/2013-December/220302.html
Thanks,
Jonas
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v5 2/2] ARM: mach-moxart: add MOXA ART SoC device tree files
@ 2013-12-18 13:10 ` Jonas Jensen
0 siblings, 0 replies; 16+ messages in thread
From: Jonas Jensen @ 2013-12-18 13:10 UTC (permalink / raw)
To: Peter Crosthwaite, Soren Brinkmann
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA, arm-DgEjT+Ai2ygdnm+yROfE0A,
Russell King - ARM Linux, Arnd Bergmann, Olof Johansson,
linux-0h96xk9xTtrk1uMJSBkQmQ
Thanks for the replies, changes should be in v6.
On 18 December 2013 00:29, Peter Crosthwaite
<peter.crosthwaite-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org> wrote:
>> + clocks {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + ref12: ref12M {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <12000000>;
>
> Crystal board level?
I couldn't move this due to fixed-clock load order.
See my comments in v6 cover letter:
http://lists.infradead.org/pipermail/linux-arm-kernel/2013-December/220302.html
Thanks,
Jonas
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v5 2/2] ARM: mach-moxart: add MOXA ART SoC device tree files
@ 2013-12-18 13:10 ` Jonas Jensen
0 siblings, 0 replies; 16+ messages in thread
From: Jonas Jensen @ 2013-12-18 13:10 UTC (permalink / raw)
To: linux-arm-kernel
Thanks for the replies, changes should be in v6.
On 18 December 2013 00:29, Peter Crosthwaite
<peter.crosthwaite@xilinx.com> wrote:
>> + clocks {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + ref12: ref12M {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <12000000>;
>
> Crystal board level?
I couldn't move this due to fixed-clock load order.
See my comments in v6 cover letter:
http://lists.infradead.org/pipermail/linux-arm-kernel/2013-December/220302.html
Thanks,
Jonas
^ permalink raw reply [flat|nested] 16+ messages in thread
end of thread, other threads:[~2013-12-18 13:10 UTC | newest]
Thread overview: 16+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-12-17 15:38 [PATCH v5 0/2] ARM: mach-moxart: add MOXA ART SoC support Jonas Jensen
2013-12-17 15:38 ` Jonas Jensen
2013-12-17 15:38 ` Jonas Jensen
2013-12-17 15:38 ` [PATCH v5 1/2] ARM: mach-moxart: add MOXA ART SoC platform files Jonas Jensen
2013-12-17 15:38 ` Jonas Jensen
2013-12-17 15:38 ` [PATCH v5 2/2] ARM: mach-moxart: add MOXA ART SoC device tree files Jonas Jensen
2013-12-17 15:38 ` Jonas Jensen
2013-12-17 23:29 ` Peter Crosthwaite
2013-12-17 23:29 ` Peter Crosthwaite
2013-12-17 23:29 ` Peter Crosthwaite
2013-12-18 13:10 ` Jonas Jensen
2013-12-18 13:10 ` Jonas Jensen
2013-12-18 13:10 ` Jonas Jensen
2013-12-17 23:57 ` Sören Brinkmann
2013-12-17 23:57 ` Sören Brinkmann
2013-12-17 23:57 ` Sören Brinkmann
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.