[PATCH v4 0/3] add hisilicon hip04 ethernet driver

[PATCH v4 0/3] add hisilicon hip04 ethernet driver

[Zhangfei Gao]

v4:
Modify accoringly to the suggetion from Arnd, Florian, Eric, David
Use of_parse_phandle_with_fixed_args & syscon_node_to_regmap get ppe info
Add skb_orphan() and tx_timer for reclaim since no tx_finished interrupt
Update timeout, and move of_phy_connect to probe to reuse open/stop

v3:
Suggest from Arnd, use syscon & regmap_write/read to replace static void __iomem *ppebase.
Modify hisilicon-hip04-net.txt accrordingly to suggestion from Florian and Sergei.

v2:
Got many suggestions from Russell, Arnd, Florian, Mark and Sergei
Remove memcpy, use dma_map/unmap_single, use dma_alloc_coherent rather than dma_pool, etc.
Refer property in ethernet.txt, change ppe description, etc.

Zhangfei Gao (3):
  Documentation: add Device tree bindings for Hisilicon hip04 ethernet
  net: hisilicon: new hip04 MDIO driver
  net: hisilicon: new hip04 ethernet driver

 .../bindings/net/hisilicon-hip04-net.txt           |   88 +++
 drivers/net/ethernet/Kconfig                       |    1 +
 drivers/net/ethernet/Makefile                      |    1 +
 drivers/net/ethernet/hisilicon/Kconfig             |   32 +
 drivers/net/ethernet/hisilicon/Makefile            |    5 +
 drivers/net/ethernet/hisilicon/hip04_eth.c         |  764 ++++++++++++++++++++
 drivers/net/ethernet/hisilicon/hip04_mdio.c        |  186 +++++
 7 files changed, 1077 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_eth.c
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

-- 
1.7.9.5

[PATCH v4 0/3] add hisilicon hip04 ethernet driver

[Zhangfei Gao]

v4:
Modify accoringly to the suggetion from Arnd, Florian, Eric, David
Use of_parse_phandle_with_fixed_args & syscon_node_to_regmap get ppe info
Add skb_orphan() and tx_timer for reclaim since no tx_finished interrupt
Update timeout, and move of_phy_connect to probe to reuse open/stop

v3:
Suggest from Arnd, use syscon & regmap_write/read to replace static void __iomem *ppebase.
Modify hisilicon-hip04-net.txt accrordingly to suggestion from Florian and Sergei.

v2:
Got many suggestions from Russell, Arnd, Florian, Mark and Sergei
Remove memcpy, use dma_map/unmap_single, use dma_alloc_coherent rather than dma_pool, etc.
Refer property in ethernet.txt, change ppe description, etc.

Zhangfei Gao (3):
  Documentation: add Device tree bindings for Hisilicon hip04 ethernet
  net: hisilicon: new hip04 MDIO driver
  net: hisilicon: new hip04 ethernet driver

 .../bindings/net/hisilicon-hip04-net.txt           |   88 +++
 drivers/net/ethernet/Kconfig                       |    1 +
 drivers/net/ethernet/Makefile                      |    1 +
 drivers/net/ethernet/hisilicon/Kconfig             |   32 +
 drivers/net/ethernet/hisilicon/Makefile            |    5 +
 drivers/net/ethernet/hisilicon/hip04_eth.c         |  764 ++++++++++++++++++++
 drivers/net/ethernet/hisilicon/hip04_mdio.c        |  186 +++++
 7 files changed, 1077 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_eth.c
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

-- 
1.7.9.5

[PATCH 1/3] Documentation: add Device tree bindings for Hisilicon hip04 ethernet

[Zhangfei Gao]

This patch adds the Device Tree bindings for the Hisilicon hip04
Ethernet controller, including 100M / 1000M controller.

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 .../bindings/net/hisilicon-hip04-net.txt           |   88 ++++++++++++++++++++
 1 file changed, 88 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt

diff --git a/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt
new file mode 100644
index 0000000..988fc69
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt
@@ -0,0 +1,88 @@
+Hisilicon hip04 Ethernet Controller
+
+* Ethernet controller node
+
+Required properties:
+- compatible: should be "hisilicon,hip04-mac".
+- reg: address and length of the register set for the device.
+- interrupts: interrupt for the device.
+- port-handle: <phandle port channel>
+	phandle, specifies a reference to the syscon ppe node
+	port, port number connected to the controller
+	channel, recv channel start from channel * number (RX_DESC_NUM)
+- phy-mode: see ethernet.txt [1].
+
+Optional properties:
+- phy-handle: see ethernet.txt [1].
+
+[1] Documentation/devicetree/bindings/net/ethernet.txt
+
+
+* Ethernet ppe node:
+Control rx & tx fifos of all ethernet controllers.
+Have 2048 recv channels shared by all ethernet controllers, only if no overlap.
+Each controller's recv channel start from channel * number (RX_DESC_NUM).
+
+Required properties:
+- compatible: "hisilicon,hip04-ppe", "syscon".
+- reg: address and length of the register set for the device.
+
+
+* MDIO bus node:
+
+Required properties:
+
+- compatible: should be "hisilicon,hip04-mdio".
+- Inherits from MDIO bus node binding [2]
+[2] Documentation/devicetree/bindings/net/phy.txt
+
+Example:
+	mdio {
+		compatible = "hisilicon,hip04-mdio";
+		reg = <0x28f1000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			marvell,reg-init = <18 0x14 0 0x8001>;
+		};
+
+		phy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			marvell,reg-init = <18 0x14 0 0x8001>;
+		};
+	};
+
+	ppe: ppe@28c0000 {
+		compatible = "hisilicon,hip04-ppe", "syscon";
+		reg = <0x28c0000 0x10000>;
+	};
+
+	fe: ethernet@28b0000 {
+		compatible = "hisilicon,hip04-mac";
+		reg = <0x28b0000 0x10000>;
+		interrupts = <0 413 4>;
+		phy-mode = "mii";
+		port-handle = <&ppe 31 0>;
+	};
+
+	ge0: ethernet@2800000 {
+		compatible = "hisilicon,hip04-mac";
+		reg = <0x2800000 0x10000>;
+		interrupts = <0 402 4>;
+		phy-mode = "sgmii";
+		port-handle = <&ppe 0 1>;
+		phy-handle = <&phy0>;
+	};
+
+	ge8: ethernet@2880000 {
+		compatible = "hisilicon,hip04-mac";
+		reg = <0x2880000 0x10000>;
+		interrupts = <0 410 4>;
+		phy-mode = "sgmii";
+		port-handle = <&ppe 8 2>;
+		phy-handle = <&phy1>;
+	};
-- 
1.7.9.5

[PATCH 1/3] Documentation: add Device tree bindings for Hisilicon hip04 ethernet

[Zhangfei Gao]

This patch adds the Device Tree bindings for the Hisilicon hip04
Ethernet controller, including 100M / 1000M controller.

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 .../bindings/net/hisilicon-hip04-net.txt           |   88 ++++++++++++++++++++
 1 file changed, 88 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt

diff --git a/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt
new file mode 100644
index 0000000..988fc69
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt
@@ -0,0 +1,88 @@
+Hisilicon hip04 Ethernet Controller
+
+* Ethernet controller node
+
+Required properties:
+- compatible: should be "hisilicon,hip04-mac".
+- reg: address and length of the register set for the device.
+- interrupts: interrupt for the device.
+- port-handle: <phandle port channel>
+	phandle, specifies a reference to the syscon ppe node
+	port, port number connected to the controller
+	channel, recv channel start from channel * number (RX_DESC_NUM)
+- phy-mode: see ethernet.txt [1].
+
+Optional properties:
+- phy-handle: see ethernet.txt [1].
+
+[1] Documentation/devicetree/bindings/net/ethernet.txt
+
+
+* Ethernet ppe node:
+Control rx & tx fifos of all ethernet controllers.
+Have 2048 recv channels shared by all ethernet controllers, only if no overlap.
+Each controller's recv channel start from channel * number (RX_DESC_NUM).
+
+Required properties:
+- compatible: "hisilicon,hip04-ppe", "syscon".
+- reg: address and length of the register set for the device.
+
+
+* MDIO bus node:
+
+Required properties:
+
+- compatible: should be "hisilicon,hip04-mdio".
+- Inherits from MDIO bus node binding [2]
+[2] Documentation/devicetree/bindings/net/phy.txt
+
+Example:
+	mdio {
+		compatible = "hisilicon,hip04-mdio";
+		reg = <0x28f1000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy at 0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			marvell,reg-init = <18 0x14 0 0x8001>;
+		};
+
+		phy1: ethernet-phy at 1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			marvell,reg-init = <18 0x14 0 0x8001>;
+		};
+	};
+
+	ppe: ppe at 28c0000 {
+		compatible = "hisilicon,hip04-ppe", "syscon";
+		reg = <0x28c0000 0x10000>;
+	};
+
+	fe: ethernet at 28b0000 {
+		compatible = "hisilicon,hip04-mac";
+		reg = <0x28b0000 0x10000>;
+		interrupts = <0 413 4>;
+		phy-mode = "mii";
+		port-handle = <&ppe 31 0>;
+	};
+
+	ge0: ethernet at 2800000 {
+		compatible = "hisilicon,hip04-mac";
+		reg = <0x2800000 0x10000>;
+		interrupts = <0 402 4>;
+		phy-mode = "sgmii";
+		port-handle = <&ppe 0 1>;
+		phy-handle = <&phy0>;
+	};
+
+	ge8: ethernet at 2880000 {
+		compatible = "hisilicon,hip04-mac";
+		reg = <0x2880000 0x10000>;
+		interrupts = <0 410 4>;
+		phy-mode = "sgmii";
+		port-handle = <&ppe 8 2>;
+		phy-handle = <&phy1>;
+	};
-- 
1.7.9.5

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   32 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  186 +++++++++++++++++++++++++++
 5 files changed, 225 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 506b024..1c8dc3d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -54,6 +54,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index c0b8789..da1a435 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..b0ee739
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,32 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about MOXA ART devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select NET_CORE
+	select PHYLIB
+	select MARVELL_PHY
+	select MFD_SYSCON
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..e4f67ca
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,186 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   32 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  186 +++++++++++++++++++++++++++
 5 files changed, 225 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 506b024..1c8dc3d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -54,6 +54,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index c0b8789..da1a435 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..b0ee739
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,32 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about MOXA ART devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select NET_CORE
+	select PHYLIB
+	select MARVELL_PHY
+	select MFD_SYSCON
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..e4f67ca
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,186 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

[PATCH 3/3] net: hisilicon: new hip04 ethernet driver

[Zhangfei Gao]

Support Hisilicon hip04 ethernet driver, including 100M / 1000M controller

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/hisilicon/Makefile    |    2 +-
 drivers/net/ethernet/hisilicon/hip04_eth.c |  769 ++++++++++++++++++++++++++++
 2 files changed, 770 insertions(+), 1 deletion(-)
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_eth.c

diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
index 1d6eb6e..5af9b54 100644
--- a/drivers/net/ethernet/hisilicon/Makefile
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -2,4 +2,4 @@
 # Makefile for the HISILICON network device drivers.
 #
 
-obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
+obj-$(CONFIG_HIP04_ETH) +=hip04_mdio.o hip04_eth.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_eth.c b/drivers/net/ethernet/hisilicon/hip04_eth.c
new file mode 100644
index 0000000..efff711
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_eth.c
@@ -0,0 +1,769 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/etherdevice.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/of_address.h>
+#include <linux/phy.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+
+#define PPE_CFG_RX_ADDR			0x100
+#define PPE_CFG_POOL_GRP		0x300
+#define PPE_CFG_RX_BUF_SIZE		0x400
+#define PPE_CFG_RX_FIFO_SIZE		0x500
+#define PPE_CURR_BUF_CNT		0xa200
+
+#define GE_DUPLEX_TYPE			0x8
+#define GE_MAX_FRM_SIZE_REG		0x3c
+#define GE_PORT_MODE			0x40
+#define GE_PORT_EN			0x44
+#define GE_SHORT_RUNTS_THR_REG		0x50
+#define GE_TX_LOCAL_PAGE_REG		0x5c
+#define GE_TRANSMIT_CONTROL_REG		0x60
+#define GE_CF_CRC_STRIP_REG		0x1b0
+#define GE_MODE_CHANGE_EN		0x1b4
+#define GE_RECV_CONTROL_REG		0x1e0
+#define GE_STATION_MAC_ADDRESS		0x210
+#define PPE_CFG_TX_PKT_BD_ADDR		0x420
+#define PPE_CFG_MAX_FRAME_LEN_REG	0x408
+#define PPE_CFG_BUS_CTRL_REG		0x424
+#define PPE_CFG_RX_CTRL_REG		0x428
+#define PPE_CFG_RX_PKT_MODE_REG		0x438
+#define PPE_CFG_QOS_VMID_GEN		0x500
+#define PPE_CFG_RX_PKT_INT		0x538
+#define PPE_INTEN			0x600
+#define PPE_INTSTS			0x608
+#define PPE_RINT			0x604
+#define PPE_CFG_STS_MODE		0x700
+#define PPE_HIS_RX_PKT_CNT		0x804
+
+/* REG_INTERRUPT */
+#define RCV_INT				BIT(10)
+#define RCV_NOBUF			BIT(8)
+#define DEF_INT_MASK			(RCV_INT | RCV_NOBUF)
+
+#define RX_DESC_NUM			64
+#define TX_DESC_NUM			64
+#define TX_NEXT(N)			(((N) + 1) & (TX_DESC_NUM-1))
+#define RX_NEXT(N)			(((N) + 1) & (RX_DESC_NUM-1))
+
+#define GMAC_PPE_RX_PKT_MAX_LEN		379
+#define GMAC_MAX_PKT_LEN		1516
+#define DESC_DEF_CFG			0x14
+#define RX_BUF_SIZE			1600
+#define RX_PKT_ERR			0x3
+#define TX_TIMEOUT			(6 * HZ)
+#define RECLAIM_PERIOD			HZ
+
+#define DRV_NAME			"hip04-ether"
+
+struct tx_desc {
+	u32 send_addr;
+	u16 reserved_16;
+	u16 send_size;
+	u32 reserved_32;
+	u32 cfg;
+	u32 wb_addr;
+} ____cacheline_aligned;
+
+struct rx_desc {
+	u16 reserved_16;
+	u16 pkt_len;
+	u32 reserve1[3];
+	u32 pkt_err;
+	u32 reserve2[4];
+};
+
+struct hip04_priv {
+	void __iomem *base;
+	int phy_mode;
+	int chan;
+	unsigned int port;
+	unsigned int speed;
+	unsigned int duplex;
+	unsigned int reg_inten;
+
+	struct napi_struct napi;
+	struct net_device *ndev;
+
+	struct tx_desc *tx_desc;
+	dma_addr_t tx_desc_dma;
+	struct sk_buff *tx_skb[TX_DESC_NUM];
+	dma_addr_t tx_phys[TX_DESC_NUM];
+	spinlock_t lock;
+	unsigned int tx_head;
+	unsigned int tx_tail;
+	unsigned int tx_count;
+
+	unsigned char *rx_buf[RX_DESC_NUM];
+	dma_addr_t rx_phys[RX_DESC_NUM];
+	unsigned int rx_head;
+	unsigned int rx_buf_size;
+
+	struct device_node *phy_node;
+	struct phy_device *phy;
+	struct regmap *map;
+	struct timer_list txtimer;
+};
+
+static void hip04_config_port(struct net_device *ndev, u32 speed, u32 duplex)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	u32 val;
+
+	priv->speed = speed;
+	priv->duplex = duplex;
+
+	switch (priv->phy_mode) {
+	case PHY_INTERFACE_MODE_SGMII:
+		if (speed == SPEED_1000)
+			val = 8;
+		else if (speed == SPEED_100)
+			val = 7;
+		else
+			val = 6;	/* SPEED_10 */
+		break;
+	case PHY_INTERFACE_MODE_MII:
+		if (speed == SPEED_100)
+			val = 1;
+		else
+			val = 0;	/* SPEED_10 */
+		break;
+	default:
+		netdev_warn(ndev, "not supported mode\n");
+		val = 0;
+		break;
+	}
+	writel_relaxed(val, priv->base + GE_PORT_MODE);
+
+	val = (duplex) ? BIT(0) : 0;
+	writel_relaxed(val, priv->base + GE_DUPLEX_TYPE);
+
+	val = BIT(0);
+	writel_relaxed(val, priv->base + GE_MODE_CHANGE_EN);
+}
+
+static void hip04_reset_ppe(struct hip04_priv *priv)
+{
+	u32 val, tmp;
+
+	do {
+		regmap_read(priv->map, priv->port * 4 + PPE_CURR_BUF_CNT, &val);
+		regmap_read(priv->map, priv->port * 4 + PPE_CFG_RX_ADDR, &tmp);
+	} while (val & 0xfff);
+}
+
+static void hip04_config_fifo(struct hip04_priv *priv)
+{
+	u32 val;
+
+	val = readl_relaxed(priv->base + PPE_CFG_STS_MODE);
+	val |= BIT(12);			/* PPE_HIS_RX_PKT_CNT read clear */
+	writel_relaxed(val, priv->base + PPE_CFG_STS_MODE);
+
+	val = BIT(priv->port);
+	regmap_write(priv->map, priv->port * 4 + PPE_CFG_POOL_GRP, val);
+
+	val = priv->port << 8;
+	val |= BIT(14);
+	writel_relaxed(val, priv->base + PPE_CFG_QOS_VMID_GEN);
+
+	val = RX_BUF_SIZE;
+	regmap_write(priv->map, priv->port * 4 + PPE_CFG_RX_BUF_SIZE, val);
+
+	val = RX_DESC_NUM << 16;	/* depth */
+	val |= BIT(11);			/* seq: first set first ues */
+	val |= RX_DESC_NUM * priv->chan;	/* start_addr */
+	regmap_write(priv->map, priv->port * 4 + PPE_CFG_RX_FIFO_SIZE, val);
+
+	/* pkt store format */
+	val = NET_IP_ALIGN << 11;	/* align */
+	writel_relaxed(val, priv->base + PPE_CFG_RX_CTRL_REG);
+
+	/* following cfg required for 1000M */
+	/* pkt mode */
+	val = BIT(18);			/* align */
+	writel_relaxed(val, priv->base + PPE_CFG_RX_PKT_MODE_REG);
+
+	/* set bus ctrl */
+	val = BIT(14);			/* buffer locally release */
+	val |= BIT(0);			/* big endian */
+	writel_relaxed(val, priv->base + PPE_CFG_BUS_CTRL_REG);
+
+	/* set max pkt len, curtail if exceed */
+	val = GMAC_PPE_RX_PKT_MAX_LEN;	/* max buffer len */
+	writel_relaxed(val, priv->base + PPE_CFG_MAX_FRAME_LEN_REG);
+
+	/* set max len of each pkt */
+	val = GMAC_MAX_PKT_LEN;		/* max buffer len */
+	writel_relaxed(val, priv->base + GE_MAX_FRM_SIZE_REG);
+
+	/* set min len of each pkt */
+	val = 31;			/* min buffer len */
+	writel_relaxed(val, priv->base + GE_SHORT_RUNTS_THR_REG);
+
+	/* tx */
+	val = readl_relaxed(priv->base + GE_TRANSMIT_CONTROL_REG);
+	val |= BIT(5);			/* tx auto neg */
+	val |= BIT(6);			/* tx add crc */
+	val |= BIT(7);			/* tx short pad through */
+	writel_relaxed(val, priv->base + GE_TRANSMIT_CONTROL_REG);
+
+	/* rx crc */
+	val = BIT(0);			/* rx strip crc */
+	writel_relaxed(val, priv->base + GE_CF_CRC_STRIP_REG);
+
+	/* rx */
+	val = readl_relaxed(priv->base + GE_RECV_CONTROL_REG);
+	val |= BIT(3);			/* rx strip pad */
+	val |= BIT(4);			/* run pkt en */
+	writel_relaxed(val, priv->base + GE_RECV_CONTROL_REG);
+
+	/* auto neg control */
+	val = BIT(0);
+	writel_relaxed(val, priv->base + GE_TX_LOCAL_PAGE_REG);
+}
+
+static void hip04_mac_enable(struct net_device *ndev)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	u32 val;
+
+	/* enable tx & rx */
+	val = readl_relaxed(priv->base + GE_PORT_EN);
+	val |= BIT(1);		/* rx*/
+	val |= BIT(2);		/* tx*/
+	writel_relaxed(val, priv->base + GE_PORT_EN);
+
+	/* clear rx int */
+	val = RCV_INT;
+	writel_relaxed(val, priv->base + PPE_RINT);
+
+	/* config recv int*/
+	val = BIT(6);		/* int threshold 1 package */
+	val |= 0x4;		/* recv timeout */
+	writel_relaxed(val, priv->base + PPE_CFG_RX_PKT_INT);
+
+	/* enable interrupt */
+	priv->reg_inten = DEF_INT_MASK;
+	writel_relaxed(priv->reg_inten, priv->base + PPE_INTEN);
+}
+
+static void hip04_mac_disable(struct net_device *ndev)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	u32 val;
+
+	/* disable int */
+	priv->reg_inten &= ~(RCV_INT | RCV_NOBUF);
+	writel_relaxed(priv->reg_inten, priv->base + PPE_INTEN);
+
+	/* disable tx & rx */
+	val = readl_relaxed(priv->base + GE_PORT_EN);
+	val &= ~(BIT(1));	/* rx*/
+	val &= ~(BIT(2));	/* tx*/
+	writel_relaxed(val, priv->base + GE_PORT_EN);
+}
+
+static void hip04_set_xmit_desc(struct hip04_priv *priv, dma_addr_t phys)
+{
+	writel(phys, priv->base + PPE_CFG_TX_PKT_BD_ADDR);
+}
+
+static void hip04_set_recv_desc(struct hip04_priv *priv, dma_addr_t phys)
+{
+	regmap_write(priv->map, priv->port * 4 + PPE_CFG_RX_ADDR, phys);
+}
+
+static u32 hip04_recv_cnt(struct hip04_priv *priv)
+{
+	return readl(priv->base + PPE_HIS_RX_PKT_CNT);
+}
+
+static void hip04_update_mac_address(struct net_device *ndev)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+
+	writel_relaxed(((ndev->dev_addr[0] << 8) | (ndev->dev_addr[1])),
+			priv->base + GE_STATION_MAC_ADDRESS);
+	writel_relaxed(((ndev->dev_addr[2] << 24) | (ndev->dev_addr[3] << 16) |
+			(ndev->dev_addr[4] << 8) | (ndev->dev_addr[5])),
+			priv->base + GE_STATION_MAC_ADDRESS + 4);
+}
+
+static int hip04_set_mac_address(struct net_device *ndev, void *addr)
+{
+	eth_mac_addr(ndev, addr);
+	hip04_update_mac_address(ndev);
+	return 0;
+}
+
+static void hip04_tx_reclaim(struct net_device *ndev, bool force)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	unsigned tx_head = priv->tx_head;
+	unsigned tx_tail = priv->tx_tail;
+	struct tx_desc *desc;
+
+	spin_lock_bh(&priv->lock);
+	while ((tx_tail != tx_head) || (priv->tx_count == TX_DESC_NUM)) {
+		if (priv->tx_phys[tx_tail]) {
+			dma_unmap_single(&ndev->dev, priv->tx_phys[tx_tail],
+				priv->tx_skb[tx_tail]->len, DMA_TO_DEVICE);
+			priv->tx_phys[tx_tail] = 0;
+		}
+		desc = &priv->tx_desc[priv->tx_tail];
+		if (desc->send_addr != 0) {
+			if (force)
+				desc->send_addr = 0;
+			else
+				break;
+		}
+		dev_kfree_skb(priv->tx_skb[tx_tail]);
+		priv->tx_skb[tx_tail] = NULL;
+		tx_tail = TX_NEXT(tx_tail);
+		priv->tx_count--;
+	}
+	priv->tx_tail = tx_tail;
+	spin_unlock_bh(&priv->lock);
+
+	if (priv->tx_count)
+		mod_timer(&priv->txtimer, jiffies + RECLAIM_PERIOD);
+
+	if (unlikely(netif_queue_stopped(ndev)) &&
+		(priv->tx_count < TX_DESC_NUM))
+		netif_wake_queue(ndev);
+}
+
+static void hip04_xmit_timer(unsigned long data)
+{
+	struct net_device *ndev = (void *)data;
+
+	hip04_tx_reclaim(ndev, false);
+}
+
+static int hip04_mac_start_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	struct net_device_stats *stats = &ndev->stats;
+	unsigned int tx_head = priv->tx_head;
+	struct tx_desc *desc = &priv->tx_desc[tx_head];
+	dma_addr_t phys;
+
+	hip04_tx_reclaim(ndev, false);
+	mod_timer(&priv->txtimer, jiffies + RECLAIM_PERIOD);
+
+	if (priv->tx_count >= TX_DESC_NUM) {
+		netif_stop_queue(ndev);
+		return NETDEV_TX_BUSY;
+	}
+
+	phys = dma_map_single(&ndev->dev, skb->data, skb->len, DMA_TO_DEVICE);
+	if (dma_mapping_error(&ndev->dev, phys)) {
+		dev_kfree_skb(skb);
+		return NETDEV_TX_OK;
+	}
+
+	priv->tx_skb[tx_head] = skb;
+	priv->tx_phys[tx_head] = phys;
+	desc->send_addr = cpu_to_be32(phys);
+	desc->send_size = cpu_to_be16(skb->len);
+	desc->cfg = cpu_to_be32(DESC_DEF_CFG);
+	phys = priv->tx_desc_dma + tx_head * sizeof(struct tx_desc);
+	desc->wb_addr = cpu_to_be32(phys);
+	skb_tx_timestamp(skb);
+
+	/* Don't wait up for transmitted skbs to be freed. */
+	skb_orphan(skb);
+
+	hip04_set_xmit_desc(priv, phys);
+	priv->tx_head = TX_NEXT(tx_head);
+
+	stats->tx_bytes += skb->len;
+	stats->tx_packets++;
+	priv->tx_count++;
+
+	return NETDEV_TX_OK;
+}
+
+static int hip04_rx_poll(struct napi_struct *napi, int budget)
+{
+	struct hip04_priv *priv = container_of(napi, struct hip04_priv, napi);
+	struct net_device *ndev = priv->ndev;
+	struct net_device_stats *stats = &ndev->stats;
+	unsigned int cnt = hip04_recv_cnt(priv);
+	struct rx_desc *desc;
+	struct sk_buff *skb;
+	unsigned char *buf;
+	bool last = false;
+	dma_addr_t phys;
+	int rx = 0;
+	u16 len;
+	u32 err;
+
+	while (cnt && !last) {
+		buf = priv->rx_buf[priv->rx_head];
+		skb = build_skb(buf, priv->rx_buf_size);
+		if (unlikely(!skb))
+			net_dbg_ratelimited("build_skb failed\n");
+
+		dma_unmap_single(&ndev->dev, priv->rx_phys[priv->rx_head],
+				RX_BUF_SIZE, DMA_FROM_DEVICE);
+		priv->rx_phys[priv->rx_head] = 0;
+
+		desc = (struct rx_desc *)skb->data;
+		len = be16_to_cpu(desc->pkt_len);
+		err = be32_to_cpu(desc->pkt_err);
+
+		if (len > RX_BUF_SIZE)
+			len = RX_BUF_SIZE;
+
+		if (0 == len) {
+			dev_kfree_skb_any(skb);
+			last = true;
+		} else if (err & RX_PKT_ERR) {
+			dev_kfree_skb_any(skb);
+			stats->rx_dropped++;
+			stats->rx_errors++;
+		} else {
+			skb_reserve(skb, NET_SKB_PAD + NET_IP_ALIGN);
+			skb_put(skb, len);
+			skb->protocol = eth_type_trans(skb, ndev);
+			napi_gro_receive(&priv->napi, skb);
+			stats->rx_packets++;
+			stats->rx_bytes += len;
+			rx++;
+		}
+
+		buf = netdev_alloc_frag(priv->rx_buf_size);
+		if (!buf)
+			return -ENOMEM;
+		phys = dma_map_single(&ndev->dev, buf,
+				RX_BUF_SIZE, DMA_FROM_DEVICE);
+		if (dma_mapping_error(&ndev->dev, phys))
+			return -EIO;
+		priv->rx_buf[priv->rx_head] = buf;
+		priv->rx_phys[priv->rx_head] = phys;
+		hip04_set_recv_desc(priv, phys);
+
+		priv->rx_head = RX_NEXT(priv->rx_head);
+		if (rx >= budget)
+			break;
+
+		if (--cnt == 0)
+			cnt = hip04_recv_cnt(priv);
+	}
+
+	if (rx < budget) {
+		napi_complete(napi);
+
+		/* enable rx interrupt */
+		priv->reg_inten |= RCV_INT | RCV_NOBUF;
+		writel_relaxed(priv->reg_inten, priv->base + PPE_INTEN);
+	}
+
+	return rx;
+}
+
+static irqreturn_t hip04_mac_interrupt(int irq, void *dev_id)
+{
+	struct net_device *ndev = (struct net_device *) dev_id;
+	struct hip04_priv *priv = netdev_priv(ndev);
+	u32 ists = readl_relaxed(priv->base + PPE_INTSTS);
+
+	writel_relaxed(DEF_INT_MASK, priv->base + PPE_RINT);
+
+	if (ists & (RCV_INT | RCV_NOBUF)) {
+		/* disable rx interrupt */
+		priv->reg_inten &= ~(RCV_INT | RCV_NOBUF);
+		writel_relaxed(priv->reg_inten, priv->base + PPE_INTEN);
+		napi_schedule(&priv->napi);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static void hip04_adjust_link(struct net_device *ndev)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	struct phy_device *phy = priv->phy;
+
+	if ((priv->speed != phy->speed) || (priv->duplex != phy->duplex)) {
+		hip04_config_port(ndev, phy->speed, phy->duplex);
+		phy_print_status(phy);
+	}
+}
+
+static int hip04_mac_open(struct net_device *ndev)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	int i;
+
+	priv->rx_head = 0;
+	priv->tx_head = 0;
+	priv->tx_tail = 0;
+	priv->tx_count = 0;
+
+	hip04_reset_ppe(priv);
+	for (i = 0; i < RX_DESC_NUM; i++) {
+		dma_addr_t phys;
+
+		phys = dma_map_single(&ndev->dev, priv->rx_buf[i],
+				RX_BUF_SIZE, DMA_FROM_DEVICE);
+		if (dma_mapping_error(&ndev->dev, phys))
+			return -EIO;
+
+		priv->rx_phys[i] = phys;
+		hip04_set_recv_desc(priv, phys);
+	}
+
+	if (priv->phy)
+		phy_start(priv->phy);
+
+	netif_start_queue(ndev);
+	hip04_mac_enable(ndev);
+	napi_enable(&priv->napi);
+
+	return 0;
+}
+
+static int hip04_mac_stop(struct net_device *ndev)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	int i;
+
+	napi_disable(&priv->napi);
+	netif_stop_queue(ndev);
+	hip04_mac_disable(ndev);
+	hip04_tx_reclaim(ndev, true);
+	hip04_reset_ppe(priv);
+
+	if (priv->phy)
+		phy_stop(priv->phy);
+
+	for (i = 0; i < RX_DESC_NUM; i++) {
+		if (priv->rx_phys[i]) {
+			dma_unmap_single(&ndev->dev, priv->rx_phys[i],
+					RX_BUF_SIZE, DMA_FROM_DEVICE);
+			priv->rx_phys[i] = 0;
+		}
+	}
+
+	return 0;
+}
+
+static void hip04_timeout(struct net_device *ndev)
+{
+	hip04_mac_stop(ndev);
+	hip04_mac_open(ndev);
+	return;
+}
+
+static struct net_device_ops hip04_netdev_ops = {
+	.ndo_open		= hip04_mac_open,
+	.ndo_stop		= hip04_mac_stop,
+	.ndo_start_xmit		= hip04_mac_start_xmit,
+	.ndo_set_mac_address	= hip04_set_mac_address,
+	.ndo_tx_timeout         = hip04_timeout,
+	.ndo_validate_addr	= eth_validate_addr,
+	.ndo_change_mtu		= eth_change_mtu,
+};
+
+static int hip04_alloc_ring(struct net_device *ndev, struct device *d)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	int i;
+
+	priv->tx_desc = dma_alloc_coherent(d,
+			TX_DESC_NUM * sizeof(struct tx_desc),
+			&priv->tx_desc_dma, GFP_KERNEL);
+	if (!priv->tx_desc)
+		return -ENOMEM;
+
+	priv->rx_buf_size = RX_BUF_SIZE +
+			    SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
+	for (i = 0; i < RX_DESC_NUM; i++) {
+		priv->rx_buf[i] = netdev_alloc_frag(priv->rx_buf_size);
+		if (!priv->rx_buf[i])
+			return -ENOMEM;
+	}
+
+	return 0;
+}
+
+static void hip04_free_ring(struct net_device *ndev, struct device *d)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	int i;
+
+	for (i = 0; i < RX_DESC_NUM; i++)
+		if (priv->rx_buf[i])
+			put_page(virt_to_head_page(priv->rx_buf[i]));
+
+	for (i = 0; i < TX_DESC_NUM; i++)
+		if (priv->tx_skb[i])
+			dev_kfree_skb_any(priv->tx_skb[i]);
+
+	dma_free_coherent(d, TX_DESC_NUM * sizeof(struct tx_desc),
+			priv->tx_desc, priv->tx_desc_dma);
+}
+
+static int hip04_mac_probe(struct platform_device *pdev)
+{
+	struct device *d = &pdev->dev;
+	struct device_node *node = d->of_node;
+	struct of_phandle_args arg;
+	struct net_device *ndev;
+	struct hip04_priv *priv;
+	struct resource *res;
+	unsigned int irq;
+	int ret;
+
+	ndev = alloc_etherdev(sizeof(struct hip04_priv));
+	if (!ndev)
+		return -ENOMEM;
+
+	priv = netdev_priv(ndev);
+	priv->ndev = ndev;
+	platform_set_drvdata(pdev, ndev);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(d, res);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto init_fail;
+	}
+
+	ret = of_parse_phandle_with_fixed_args(node, "port-handle", 2, 0, &arg);
+	if (ret < 0) {
+		dev_warn(d, "no port-handle\n");
+		goto init_fail;
+	}
+
+	priv->port = arg.args[0];
+	priv->chan = arg.args[1];
+
+	priv->map = syscon_node_to_regmap(arg.np);
+	if (IS_ERR(priv->map)) {
+		dev_warn(d, "no syscon hisilicon,hip04-ppe\n");
+		ret = PTR_ERR(priv->map);
+		goto init_fail;
+	}
+
+	priv->phy_mode = of_get_phy_mode(node);
+	if (priv->phy_mode < 0) {
+		dev_warn(d, "not find phy-mode\n");
+		ret = -EINVAL;
+		goto init_fail;
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq <= 0) {
+		ret = -EINVAL;
+		goto init_fail;
+	}
+
+	ether_setup(ndev);
+	ndev->netdev_ops = &hip04_netdev_ops;
+	ndev->watchdog_timeo = TX_TIMEOUT;
+	ndev->priv_flags |= IFF_UNICAST_FLT;
+	ndev->irq = irq;
+	netif_napi_add(ndev, &priv->napi, hip04_rx_poll, RX_DESC_NUM);
+	SET_NETDEV_DEV(ndev, &pdev->dev);
+
+	hip04_reset_ppe(priv);
+	if (priv->phy_mode == PHY_INTERFACE_MODE_MII)
+		hip04_config_port(ndev, SPEED_100, DUPLEX_FULL);
+
+	hip04_config_fifo(priv);
+	random_ether_addr(ndev->dev_addr);
+	hip04_update_mac_address(ndev);
+
+	ret = hip04_alloc_ring(ndev, d);
+	if (ret) {
+		netdev_err(ndev, "alloc ring fail\n");
+		goto alloc_fail;
+	}
+
+	ret = devm_request_irq(d, irq, hip04_mac_interrupt,
+				0, pdev->name, ndev);
+	if (ret) {
+		netdev_err(ndev, "devm_request_irq failed\n");
+		goto alloc_fail;
+	}
+
+	priv->phy_node = of_parse_phandle(node, "phy-handle", 0);
+	if (priv->phy_node) {
+		priv->phy = of_phy_connect(ndev, priv->phy_node,
+			&hip04_adjust_link, 0, priv->phy_mode);
+		if (!priv->phy)
+			return -EPROBE_DEFER;
+	}
+
+	setup_timer(&priv->txtimer, hip04_xmit_timer, (unsigned long) ndev);
+	ret = register_netdev(ndev);
+	if (ret) {
+		free_netdev(ndev);
+		goto alloc_fail;
+	}
+
+	return 0;
+
+alloc_fail:
+	hip04_free_ring(ndev, d);
+init_fail:
+	of_node_put(priv->phy_node);
+	free_netdev(ndev);
+	return ret;
+}
+
+static int hip04_remove(struct platform_device *pdev)
+{
+	struct net_device *ndev = platform_get_drvdata(pdev);
+	struct hip04_priv *priv = netdev_priv(ndev);
+	struct device *d = &pdev->dev;
+
+	if (priv->phy)
+		phy_disconnect(priv->phy);
+
+	del_timer_sync(&priv->txtimer);
+	hip04_free_ring(ndev, d);
+	unregister_netdev(ndev);
+	free_irq(ndev->irq, ndev);
+	of_node_put(priv->phy_node);
+	free_netdev(ndev);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mac_match[] = {
+	{ .compatible = "hisilicon,hip04-mac" },
+	{ }
+};
+
+static struct platform_driver hip04_mac_driver = {
+	.probe	= hip04_mac_probe,
+	.remove	= hip04_remove,
+	.driver	= {
+		.name		= DRV_NAME,
+		.owner		= THIS_MODULE,
+		.of_match_table	= hip04_mac_match,
+	},
+};
+module_platform_driver(hip04_mac_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 Ethernet driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-ether");
-- 
1.7.9.5

[PATCH 3/3] net: hisilicon: new hip04 ethernet driver

[Zhangfei Gao]

Support Hisilicon hip04 ethernet driver, including 100M / 1000M controller

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/hisilicon/Makefile    |    2 +-
 drivers/net/ethernet/hisilicon/hip04_eth.c |  769 ++++++++++++++++++++++++++++
 2 files changed, 770 insertions(+), 1 deletion(-)
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_eth.c

diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
index 1d6eb6e..5af9b54 100644
--- a/drivers/net/ethernet/hisilicon/Makefile
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -2,4 +2,4 @@
 # Makefile for the HISILICON network device drivers.
 #
 
-obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
+obj-$(CONFIG_HIP04_ETH) +=hip04_mdio.o hip04_eth.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_eth.c b/drivers/net/ethernet/hisilicon/hip04_eth.c
new file mode 100644
index 0000000..efff711
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_eth.c
@@ -0,0 +1,769 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/etherdevice.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/of_address.h>
+#include <linux/phy.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+
+#define PPE_CFG_RX_ADDR			0x100
+#define PPE_CFG_POOL_GRP		0x300
+#define PPE_CFG_RX_BUF_SIZE		0x400
+#define PPE_CFG_RX_FIFO_SIZE		0x500
+#define PPE_CURR_BUF_CNT		0xa200
+
+#define GE_DUPLEX_TYPE			0x8
+#define GE_MAX_FRM_SIZE_REG		0x3c
+#define GE_PORT_MODE			0x40
+#define GE_PORT_EN			0x44
+#define GE_SHORT_RUNTS_THR_REG		0x50
+#define GE_TX_LOCAL_PAGE_REG		0x5c
+#define GE_TRANSMIT_CONTROL_REG		0x60
+#define GE_CF_CRC_STRIP_REG		0x1b0
+#define GE_MODE_CHANGE_EN		0x1b4
+#define GE_RECV_CONTROL_REG		0x1e0
+#define GE_STATION_MAC_ADDRESS		0x210
+#define PPE_CFG_TX_PKT_BD_ADDR		0x420
+#define PPE_CFG_MAX_FRAME_LEN_REG	0x408
+#define PPE_CFG_BUS_CTRL_REG		0x424
+#define PPE_CFG_RX_CTRL_REG		0x428
+#define PPE_CFG_RX_PKT_MODE_REG		0x438
+#define PPE_CFG_QOS_VMID_GEN		0x500
+#define PPE_CFG_RX_PKT_INT		0x538
+#define PPE_INTEN			0x600
+#define PPE_INTSTS			0x608
+#define PPE_RINT			0x604
+#define PPE_CFG_STS_MODE		0x700
+#define PPE_HIS_RX_PKT_CNT		0x804
+
+/* REG_INTERRUPT */
+#define RCV_INT				BIT(10)
+#define RCV_NOBUF			BIT(8)
+#define DEF_INT_MASK			(RCV_INT | RCV_NOBUF)
+
+#define RX_DESC_NUM			64
+#define TX_DESC_NUM			64
+#define TX_NEXT(N)			(((N) + 1) & (TX_DESC_NUM-1))
+#define RX_NEXT(N)			(((N) + 1) & (RX_DESC_NUM-1))
+
+#define GMAC_PPE_RX_PKT_MAX_LEN		379
+#define GMAC_MAX_PKT_LEN		1516
+#define DESC_DEF_CFG			0x14
+#define RX_BUF_SIZE			1600
+#define RX_PKT_ERR			0x3
+#define TX_TIMEOUT			(6 * HZ)
+#define RECLAIM_PERIOD			HZ
+
+#define DRV_NAME			"hip04-ether"
+
+struct tx_desc {
+	u32 send_addr;
+	u16 reserved_16;
+	u16 send_size;
+	u32 reserved_32;
+	u32 cfg;
+	u32 wb_addr;
+} ____cacheline_aligned;
+
+struct rx_desc {
+	u16 reserved_16;
+	u16 pkt_len;
+	u32 reserve1[3];
+	u32 pkt_err;
+	u32 reserve2[4];
+};
+
+struct hip04_priv {
+	void __iomem *base;
+	int phy_mode;
+	int chan;
+	unsigned int port;
+	unsigned int speed;
+	unsigned int duplex;
+	unsigned int reg_inten;
+
+	struct napi_struct napi;
+	struct net_device *ndev;
+
+	struct tx_desc *tx_desc;
+	dma_addr_t tx_desc_dma;
+	struct sk_buff *tx_skb[TX_DESC_NUM];
+	dma_addr_t tx_phys[TX_DESC_NUM];
+	spinlock_t lock;
+	unsigned int tx_head;
+	unsigned int tx_tail;
+	unsigned int tx_count;
+
+	unsigned char *rx_buf[RX_DESC_NUM];
+	dma_addr_t rx_phys[RX_DESC_NUM];
+	unsigned int rx_head;
+	unsigned int rx_buf_size;
+
+	struct device_node *phy_node;
+	struct phy_device *phy;
+	struct regmap *map;
+	struct timer_list txtimer;
+};
+
+static void hip04_config_port(struct net_device *ndev, u32 speed, u32 duplex)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	u32 val;
+
+	priv->speed = speed;
+	priv->duplex = duplex;
+
+	switch (priv->phy_mode) {
+	case PHY_INTERFACE_MODE_SGMII:
+		if (speed == SPEED_1000)
+			val = 8;
+		else if (speed == SPEED_100)
+			val = 7;
+		else
+			val = 6;	/* SPEED_10 */
+		break;
+	case PHY_INTERFACE_MODE_MII:
+		if (speed == SPEED_100)
+			val = 1;
+		else
+			val = 0;	/* SPEED_10 */
+		break;
+	default:
+		netdev_warn(ndev, "not supported mode\n");
+		val = 0;
+		break;
+	}
+	writel_relaxed(val, priv->base + GE_PORT_MODE);
+
+	val = (duplex) ? BIT(0) : 0;
+	writel_relaxed(val, priv->base + GE_DUPLEX_TYPE);
+
+	val = BIT(0);
+	writel_relaxed(val, priv->base + GE_MODE_CHANGE_EN);
+}
+
+static void hip04_reset_ppe(struct hip04_priv *priv)
+{
+	u32 val, tmp;
+
+	do {
+		regmap_read(priv->map, priv->port * 4 + PPE_CURR_BUF_CNT, &val);
+		regmap_read(priv->map, priv->port * 4 + PPE_CFG_RX_ADDR, &tmp);
+	} while (val & 0xfff);
+}
+
+static void hip04_config_fifo(struct hip04_priv *priv)
+{
+	u32 val;
+
+	val = readl_relaxed(priv->base + PPE_CFG_STS_MODE);
+	val |= BIT(12);			/* PPE_HIS_RX_PKT_CNT read clear */
+	writel_relaxed(val, priv->base + PPE_CFG_STS_MODE);
+
+	val = BIT(priv->port);
+	regmap_write(priv->map, priv->port * 4 + PPE_CFG_POOL_GRP, val);
+
+	val = priv->port << 8;
+	val |= BIT(14);
+	writel_relaxed(val, priv->base + PPE_CFG_QOS_VMID_GEN);
+
+	val = RX_BUF_SIZE;
+	regmap_write(priv->map, priv->port * 4 + PPE_CFG_RX_BUF_SIZE, val);
+
+	val = RX_DESC_NUM << 16;	/* depth */
+	val |= BIT(11);			/* seq: first set first ues */
+	val |= RX_DESC_NUM * priv->chan;	/* start_addr */
+	regmap_write(priv->map, priv->port * 4 + PPE_CFG_RX_FIFO_SIZE, val);
+
+	/* pkt store format */
+	val = NET_IP_ALIGN << 11;	/* align */
+	writel_relaxed(val, priv->base + PPE_CFG_RX_CTRL_REG);
+
+	/* following cfg required for 1000M */
+	/* pkt mode */
+	val = BIT(18);			/* align */
+	writel_relaxed(val, priv->base + PPE_CFG_RX_PKT_MODE_REG);
+
+	/* set bus ctrl */
+	val = BIT(14);			/* buffer locally release */
+	val |= BIT(0);			/* big endian */
+	writel_relaxed(val, priv->base + PPE_CFG_BUS_CTRL_REG);
+
+	/* set max pkt len, curtail if exceed */
+	val = GMAC_PPE_RX_PKT_MAX_LEN;	/* max buffer len */
+	writel_relaxed(val, priv->base + PPE_CFG_MAX_FRAME_LEN_REG);
+
+	/* set max len of each pkt */
+	val = GMAC_MAX_PKT_LEN;		/* max buffer len */
+	writel_relaxed(val, priv->base + GE_MAX_FRM_SIZE_REG);
+
+	/* set min len of each pkt */
+	val = 31;			/* min buffer len */
+	writel_relaxed(val, priv->base + GE_SHORT_RUNTS_THR_REG);
+
+	/* tx */
+	val = readl_relaxed(priv->base + GE_TRANSMIT_CONTROL_REG);
+	val |= BIT(5);			/* tx auto neg */
+	val |= BIT(6);			/* tx add crc */
+	val |= BIT(7);			/* tx short pad through */
+	writel_relaxed(val, priv->base + GE_TRANSMIT_CONTROL_REG);
+
+	/* rx crc */
+	val = BIT(0);			/* rx strip crc */
+	writel_relaxed(val, priv->base + GE_CF_CRC_STRIP_REG);
+
+	/* rx */
+	val = readl_relaxed(priv->base + GE_RECV_CONTROL_REG);
+	val |= BIT(3);			/* rx strip pad */
+	val |= BIT(4);			/* run pkt en */
+	writel_relaxed(val, priv->base + GE_RECV_CONTROL_REG);
+
+	/* auto neg control */
+	val = BIT(0);
+	writel_relaxed(val, priv->base + GE_TX_LOCAL_PAGE_REG);
+}
+
+static void hip04_mac_enable(struct net_device *ndev)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	u32 val;
+
+	/* enable tx & rx */
+	val = readl_relaxed(priv->base + GE_PORT_EN);
+	val |= BIT(1);		/* rx*/
+	val |= BIT(2);		/* tx*/
+	writel_relaxed(val, priv->base + GE_PORT_EN);
+
+	/* clear rx int */
+	val = RCV_INT;
+	writel_relaxed(val, priv->base + PPE_RINT);
+
+	/* config recv int*/
+	val = BIT(6);		/* int threshold 1 package */
+	val |= 0x4;		/* recv timeout */
+	writel_relaxed(val, priv->base + PPE_CFG_RX_PKT_INT);
+
+	/* enable interrupt */
+	priv->reg_inten = DEF_INT_MASK;
+	writel_relaxed(priv->reg_inten, priv->base + PPE_INTEN);
+}
+
+static void hip04_mac_disable(struct net_device *ndev)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	u32 val;
+
+	/* disable int */
+	priv->reg_inten &= ~(RCV_INT | RCV_NOBUF);
+	writel_relaxed(priv->reg_inten, priv->base + PPE_INTEN);
+
+	/* disable tx & rx */
+	val = readl_relaxed(priv->base + GE_PORT_EN);
+	val &= ~(BIT(1));	/* rx*/
+	val &= ~(BIT(2));	/* tx*/
+	writel_relaxed(val, priv->base + GE_PORT_EN);
+}
+
+static void hip04_set_xmit_desc(struct hip04_priv *priv, dma_addr_t phys)
+{
+	writel(phys, priv->base + PPE_CFG_TX_PKT_BD_ADDR);
+}
+
+static void hip04_set_recv_desc(struct hip04_priv *priv, dma_addr_t phys)
+{
+	regmap_write(priv->map, priv->port * 4 + PPE_CFG_RX_ADDR, phys);
+}
+
+static u32 hip04_recv_cnt(struct hip04_priv *priv)
+{
+	return readl(priv->base + PPE_HIS_RX_PKT_CNT);
+}
+
+static void hip04_update_mac_address(struct net_device *ndev)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+
+	writel_relaxed(((ndev->dev_addr[0] << 8) | (ndev->dev_addr[1])),
+			priv->base + GE_STATION_MAC_ADDRESS);
+	writel_relaxed(((ndev->dev_addr[2] << 24) | (ndev->dev_addr[3] << 16) |
+			(ndev->dev_addr[4] << 8) | (ndev->dev_addr[5])),
+			priv->base + GE_STATION_MAC_ADDRESS + 4);
+}
+
+static int hip04_set_mac_address(struct net_device *ndev, void *addr)
+{
+	eth_mac_addr(ndev, addr);
+	hip04_update_mac_address(ndev);
+	return 0;
+}
+
+static void hip04_tx_reclaim(struct net_device *ndev, bool force)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	unsigned tx_head = priv->tx_head;
+	unsigned tx_tail = priv->tx_tail;
+	struct tx_desc *desc;
+
+	spin_lock_bh(&priv->lock);
+	while ((tx_tail != tx_head) || (priv->tx_count == TX_DESC_NUM)) {
+		if (priv->tx_phys[tx_tail]) {
+			dma_unmap_single(&ndev->dev, priv->tx_phys[tx_tail],
+				priv->tx_skb[tx_tail]->len, DMA_TO_DEVICE);
+			priv->tx_phys[tx_tail] = 0;
+		}
+		desc = &priv->tx_desc[priv->tx_tail];
+		if (desc->send_addr != 0) {
+			if (force)
+				desc->send_addr = 0;
+			else
+				break;
+		}
+		dev_kfree_skb(priv->tx_skb[tx_tail]);
+		priv->tx_skb[tx_tail] = NULL;
+		tx_tail = TX_NEXT(tx_tail);
+		priv->tx_count--;
+	}
+	priv->tx_tail = tx_tail;
+	spin_unlock_bh(&priv->lock);
+
+	if (priv->tx_count)
+		mod_timer(&priv->txtimer, jiffies + RECLAIM_PERIOD);
+
+	if (unlikely(netif_queue_stopped(ndev)) &&
+		(priv->tx_count < TX_DESC_NUM))
+		netif_wake_queue(ndev);
+}
+
+static void hip04_xmit_timer(unsigned long data)
+{
+	struct net_device *ndev = (void *)data;
+
+	hip04_tx_reclaim(ndev, false);
+}
+
+static int hip04_mac_start_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	struct net_device_stats *stats = &ndev->stats;
+	unsigned int tx_head = priv->tx_head;
+	struct tx_desc *desc = &priv->tx_desc[tx_head];
+	dma_addr_t phys;
+
+	hip04_tx_reclaim(ndev, false);
+	mod_timer(&priv->txtimer, jiffies + RECLAIM_PERIOD);
+
+	if (priv->tx_count >= TX_DESC_NUM) {
+		netif_stop_queue(ndev);
+		return NETDEV_TX_BUSY;
+	}
+
+	phys = dma_map_single(&ndev->dev, skb->data, skb->len, DMA_TO_DEVICE);
+	if (dma_mapping_error(&ndev->dev, phys)) {
+		dev_kfree_skb(skb);
+		return NETDEV_TX_OK;
+	}
+
+	priv->tx_skb[tx_head] = skb;
+	priv->tx_phys[tx_head] = phys;
+	desc->send_addr = cpu_to_be32(phys);
+	desc->send_size = cpu_to_be16(skb->len);
+	desc->cfg = cpu_to_be32(DESC_DEF_CFG);
+	phys = priv->tx_desc_dma + tx_head * sizeof(struct tx_desc);
+	desc->wb_addr = cpu_to_be32(phys);
+	skb_tx_timestamp(skb);
+
+	/* Don't wait up for transmitted skbs to be freed. */
+	skb_orphan(skb);
+
+	hip04_set_xmit_desc(priv, phys);
+	priv->tx_head = TX_NEXT(tx_head);
+
+	stats->tx_bytes += skb->len;
+	stats->tx_packets++;
+	priv->tx_count++;
+
+	return NETDEV_TX_OK;
+}
+
+static int hip04_rx_poll(struct napi_struct *napi, int budget)
+{
+	struct hip04_priv *priv = container_of(napi, struct hip04_priv, napi);
+	struct net_device *ndev = priv->ndev;
+	struct net_device_stats *stats = &ndev->stats;
+	unsigned int cnt = hip04_recv_cnt(priv);
+	struct rx_desc *desc;
+	struct sk_buff *skb;
+	unsigned char *buf;
+	bool last = false;
+	dma_addr_t phys;
+	int rx = 0;
+	u16 len;
+	u32 err;
+
+	while (cnt && !last) {
+		buf = priv->rx_buf[priv->rx_head];
+		skb = build_skb(buf, priv->rx_buf_size);
+		if (unlikely(!skb))
+			net_dbg_ratelimited("build_skb failed\n");
+
+		dma_unmap_single(&ndev->dev, priv->rx_phys[priv->rx_head],
+				RX_BUF_SIZE, DMA_FROM_DEVICE);
+		priv->rx_phys[priv->rx_head] = 0;
+
+		desc = (struct rx_desc *)skb->data;
+		len = be16_to_cpu(desc->pkt_len);
+		err = be32_to_cpu(desc->pkt_err);
+
+		if (len > RX_BUF_SIZE)
+			len = RX_BUF_SIZE;
+
+		if (0 == len) {
+			dev_kfree_skb_any(skb);
+			last = true;
+		} else if (err & RX_PKT_ERR) {
+			dev_kfree_skb_any(skb);
+			stats->rx_dropped++;
+			stats->rx_errors++;
+		} else {
+			skb_reserve(skb, NET_SKB_PAD + NET_IP_ALIGN);
+			skb_put(skb, len);
+			skb->protocol = eth_type_trans(skb, ndev);
+			napi_gro_receive(&priv->napi, skb);
+			stats->rx_packets++;
+			stats->rx_bytes += len;
+			rx++;
+		}
+
+		buf = netdev_alloc_frag(priv->rx_buf_size);
+		if (!buf)
+			return -ENOMEM;
+		phys = dma_map_single(&ndev->dev, buf,
+				RX_BUF_SIZE, DMA_FROM_DEVICE);
+		if (dma_mapping_error(&ndev->dev, phys))
+			return -EIO;
+		priv->rx_buf[priv->rx_head] = buf;
+		priv->rx_phys[priv->rx_head] = phys;
+		hip04_set_recv_desc(priv, phys);
+
+		priv->rx_head = RX_NEXT(priv->rx_head);
+		if (rx >= budget)
+			break;
+
+		if (--cnt == 0)
+			cnt = hip04_recv_cnt(priv);
+	}
+
+	if (rx < budget) {
+		napi_complete(napi);
+
+		/* enable rx interrupt */
+		priv->reg_inten |= RCV_INT | RCV_NOBUF;
+		writel_relaxed(priv->reg_inten, priv->base + PPE_INTEN);
+	}
+
+	return rx;
+}
+
+static irqreturn_t hip04_mac_interrupt(int irq, void *dev_id)
+{
+	struct net_device *ndev = (struct net_device *) dev_id;
+	struct hip04_priv *priv = netdev_priv(ndev);
+	u32 ists = readl_relaxed(priv->base + PPE_INTSTS);
+
+	writel_relaxed(DEF_INT_MASK, priv->base + PPE_RINT);
+
+	if (ists & (RCV_INT | RCV_NOBUF)) {
+		/* disable rx interrupt */
+		priv->reg_inten &= ~(RCV_INT | RCV_NOBUF);
+		writel_relaxed(priv->reg_inten, priv->base + PPE_INTEN);
+		napi_schedule(&priv->napi);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static void hip04_adjust_link(struct net_device *ndev)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	struct phy_device *phy = priv->phy;
+
+	if ((priv->speed != phy->speed) || (priv->duplex != phy->duplex)) {
+		hip04_config_port(ndev, phy->speed, phy->duplex);
+		phy_print_status(phy);
+	}
+}
+
+static int hip04_mac_open(struct net_device *ndev)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	int i;
+
+	priv->rx_head = 0;
+	priv->tx_head = 0;
+	priv->tx_tail = 0;
+	priv->tx_count = 0;
+
+	hip04_reset_ppe(priv);
+	for (i = 0; i < RX_DESC_NUM; i++) {
+		dma_addr_t phys;
+
+		phys = dma_map_single(&ndev->dev, priv->rx_buf[i],
+				RX_BUF_SIZE, DMA_FROM_DEVICE);
+		if (dma_mapping_error(&ndev->dev, phys))
+			return -EIO;
+
+		priv->rx_phys[i] = phys;
+		hip04_set_recv_desc(priv, phys);
+	}
+
+	if (priv->phy)
+		phy_start(priv->phy);
+
+	netif_start_queue(ndev);
+	hip04_mac_enable(ndev);
+	napi_enable(&priv->napi);
+
+	return 0;
+}
+
+static int hip04_mac_stop(struct net_device *ndev)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	int i;
+
+	napi_disable(&priv->napi);
+	netif_stop_queue(ndev);
+	hip04_mac_disable(ndev);
+	hip04_tx_reclaim(ndev, true);
+	hip04_reset_ppe(priv);
+
+	if (priv->phy)
+		phy_stop(priv->phy);
+
+	for (i = 0; i < RX_DESC_NUM; i++) {
+		if (priv->rx_phys[i]) {
+			dma_unmap_single(&ndev->dev, priv->rx_phys[i],
+					RX_BUF_SIZE, DMA_FROM_DEVICE);
+			priv->rx_phys[i] = 0;
+		}
+	}
+
+	return 0;
+}
+
+static void hip04_timeout(struct net_device *ndev)
+{
+	hip04_mac_stop(ndev);
+	hip04_mac_open(ndev);
+	return;
+}
+
+static struct net_device_ops hip04_netdev_ops = {
+	.ndo_open		= hip04_mac_open,
+	.ndo_stop		= hip04_mac_stop,
+	.ndo_start_xmit		= hip04_mac_start_xmit,
+	.ndo_set_mac_address	= hip04_set_mac_address,
+	.ndo_tx_timeout         = hip04_timeout,
+	.ndo_validate_addr	= eth_validate_addr,
+	.ndo_change_mtu		= eth_change_mtu,
+};
+
+static int hip04_alloc_ring(struct net_device *ndev, struct device *d)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	int i;
+
+	priv->tx_desc = dma_alloc_coherent(d,
+			TX_DESC_NUM * sizeof(struct tx_desc),
+			&priv->tx_desc_dma, GFP_KERNEL);
+	if (!priv->tx_desc)
+		return -ENOMEM;
+
+	priv->rx_buf_size = RX_BUF_SIZE +
+			    SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
+	for (i = 0; i < RX_DESC_NUM; i++) {
+		priv->rx_buf[i] = netdev_alloc_frag(priv->rx_buf_size);
+		if (!priv->rx_buf[i])
+			return -ENOMEM;
+	}
+
+	return 0;
+}
+
+static void hip04_free_ring(struct net_device *ndev, struct device *d)
+{
+	struct hip04_priv *priv = netdev_priv(ndev);
+	int i;
+
+	for (i = 0; i < RX_DESC_NUM; i++)
+		if (priv->rx_buf[i])
+			put_page(virt_to_head_page(priv->rx_buf[i]));
+
+	for (i = 0; i < TX_DESC_NUM; i++)
+		if (priv->tx_skb[i])
+			dev_kfree_skb_any(priv->tx_skb[i]);
+
+	dma_free_coherent(d, TX_DESC_NUM * sizeof(struct tx_desc),
+			priv->tx_desc, priv->tx_desc_dma);
+}
+
+static int hip04_mac_probe(struct platform_device *pdev)
+{
+	struct device *d = &pdev->dev;
+	struct device_node *node = d->of_node;
+	struct of_phandle_args arg;
+	struct net_device *ndev;
+	struct hip04_priv *priv;
+	struct resource *res;
+	unsigned int irq;
+	int ret;
+
+	ndev = alloc_etherdev(sizeof(struct hip04_priv));
+	if (!ndev)
+		return -ENOMEM;
+
+	priv = netdev_priv(ndev);
+	priv->ndev = ndev;
+	platform_set_drvdata(pdev, ndev);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(d, res);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto init_fail;
+	}
+
+	ret = of_parse_phandle_with_fixed_args(node, "port-handle", 2, 0, &arg);
+	if (ret < 0) {
+		dev_warn(d, "no port-handle\n");
+		goto init_fail;
+	}
+
+	priv->port = arg.args[0];
+	priv->chan = arg.args[1];
+
+	priv->map = syscon_node_to_regmap(arg.np);
+	if (IS_ERR(priv->map)) {
+		dev_warn(d, "no syscon hisilicon,hip04-ppe\n");
+		ret = PTR_ERR(priv->map);
+		goto init_fail;
+	}
+
+	priv->phy_mode = of_get_phy_mode(node);
+	if (priv->phy_mode < 0) {
+		dev_warn(d, "not find phy-mode\n");
+		ret = -EINVAL;
+		goto init_fail;
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq <= 0) {
+		ret = -EINVAL;
+		goto init_fail;
+	}
+
+	ether_setup(ndev);
+	ndev->netdev_ops = &hip04_netdev_ops;
+	ndev->watchdog_timeo = TX_TIMEOUT;
+	ndev->priv_flags |= IFF_UNICAST_FLT;
+	ndev->irq = irq;
+	netif_napi_add(ndev, &priv->napi, hip04_rx_poll, RX_DESC_NUM);
+	SET_NETDEV_DEV(ndev, &pdev->dev);
+
+	hip04_reset_ppe(priv);
+	if (priv->phy_mode == PHY_INTERFACE_MODE_MII)
+		hip04_config_port(ndev, SPEED_100, DUPLEX_FULL);
+
+	hip04_config_fifo(priv);
+	random_ether_addr(ndev->dev_addr);
+	hip04_update_mac_address(ndev);
+
+	ret = hip04_alloc_ring(ndev, d);
+	if (ret) {
+		netdev_err(ndev, "alloc ring fail\n");
+		goto alloc_fail;
+	}
+
+	ret = devm_request_irq(d, irq, hip04_mac_interrupt,
+				0, pdev->name, ndev);
+	if (ret) {
+		netdev_err(ndev, "devm_request_irq failed\n");
+		goto alloc_fail;
+	}
+
+	priv->phy_node = of_parse_phandle(node, "phy-handle", 0);
+	if (priv->phy_node) {
+		priv->phy = of_phy_connect(ndev, priv->phy_node,
+			&hip04_adjust_link, 0, priv->phy_mode);
+		if (!priv->phy)
+			return -EPROBE_DEFER;
+	}
+
+	setup_timer(&priv->txtimer, hip04_xmit_timer, (unsigned long) ndev);
+	ret = register_netdev(ndev);
+	if (ret) {
+		free_netdev(ndev);
+		goto alloc_fail;
+	}
+
+	return 0;
+
+alloc_fail:
+	hip04_free_ring(ndev, d);
+init_fail:
+	of_node_put(priv->phy_node);
+	free_netdev(ndev);
+	return ret;
+}
+
+static int hip04_remove(struct platform_device *pdev)
+{
+	struct net_device *ndev = platform_get_drvdata(pdev);
+	struct hip04_priv *priv = netdev_priv(ndev);
+	struct device *d = &pdev->dev;
+
+	if (priv->phy)
+		phy_disconnect(priv->phy);
+
+	del_timer_sync(&priv->txtimer);
+	hip04_free_ring(ndev, d);
+	unregister_netdev(ndev);
+	free_irq(ndev->irq, ndev);
+	of_node_put(priv->phy_node);
+	free_netdev(ndev);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mac_match[] = {
+	{ .compatible = "hisilicon,hip04-mac" },
+	{ }
+};
+
+static struct platform_driver hip04_mac_driver = {
+	.probe	= hip04_mac_probe,
+	.remove	= hip04_remove,
+	.driver	= {
+		.name		= DRV_NAME,
+		.owner		= THIS_MODULE,
+		.of_match_table	= hip04_mac_match,
+	},
+};
+module_platform_driver(hip04_mac_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 Ethernet driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-ether");
-- 
1.7.9.5

Re: [PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[David Miller]

From: Zhangfei Gao <zhangfei.gao-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Date: Fri, 28 Mar 2014 23:35:59 +0800

> +	  Note that the answer to this question doesn't directly affect the
> +	  kernel: saying N will just cause the configurator to skip all
> +	  the questions about MOXA ART devices. If you say Y, you will be asked
> +	  for your specific card in the following questions.

Please don't just cut and paste things from unrelated Kconfig entries.

This Kconfig option has nothing to do with MOXA ART devices.

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[David Miller]

From: Zhangfei Gao <zhangfei.gao@linaro.org>
Date: Fri, 28 Mar 2014 23:35:59 +0800

> +	  Note that the answer to this question doesn't directly affect the
> +	  kernel: saying N will just cause the configurator to skip all
> +	  the questions about MOXA ART devices. If you say Y, you will be asked
> +	  for your specific card in the following questions.

Please don't just cut and paste things from unrelated Kconfig entries.

This Kconfig option has nothing to do with MOXA ART devices.

Re: [PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[zhangfei]

On 03/31/2014 05:23 AM, David Miller wrote:
> From: Zhangfei Gao <zhangfei.gao@linaro.org>
> Date: Fri, 28 Mar 2014 23:35:59 +0800
>
>> +	  Note that the answer to this question doesn't directly affect the
>> +	  kernel: saying N will just cause the configurator to skip all
>> +	  the questions about MOXA ART devices. If you say Y, you will be asked
>> +	  for your specific card in the following questions.
>
> Please don't just cut and paste things from unrelated Kconfig entries.
>
> This Kconfig option has nothing to do with MOXA ART devices.
>
My bad, will update in new version.

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[zhangfei]

On 03/31/2014 05:23 AM, David Miller wrote:
> From: Zhangfei Gao <zhangfei.gao@linaro.org>
> Date: Fri, 28 Mar 2014 23:35:59 +0800
>
>> +	  Note that the answer to this question doesn't directly affect the
>> +	  kernel: saying N will just cause the configurator to skip all
>> +	  the questions about MOXA ART devices. If you say Y, you will be asked
>> +	  for your specific card in the following questions.
>
> Please don't just cut and paste things from unrelated Kconfig entries.
>
> This Kconfig option has nothing to do with MOXA ART devices.
>
My bad, will update in new version.

Re: [PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[David Miller]

From: Zhangfei Gao <zhangfei.gao@linaro.org>
Date: Sat,  5 Apr 2014 12:35:05 +0800

> +}
> +
> +
> +static int hip04_mdio_reset(struct mii_bus *bus)

Please one empty line between functions, not two.

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[David Miller]

From: Zhangfei Gao <zhangfei.gao@linaro.org>
Date: Sat,  5 Apr 2014 12:35:05 +0800

> +}
> +
> +
> +static int hip04_mdio_reset(struct mii_bus *bus)

Please one empty line between functions, not two.

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   31 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  186 +++++++++++++++++++++++++++
 5 files changed, 224 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 506b024..1c8dc3d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -54,6 +54,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index c0b8789..da1a435 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..628537f
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,31 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Hisilicon devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select PHYLIB
+	select MARVELL_PHY
+	select MFD_SYSCON
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..e4f67ca
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,186 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   31 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  186 +++++++++++++++++++++++++++
 5 files changed, 224 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 506b024..1c8dc3d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -54,6 +54,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index c0b8789..da1a435 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..628537f
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,31 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Hisilicon devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select PHYLIB
+	select MARVELL_PHY
+	select MFD_SYSCON
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..e4f67ca
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,186 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

Re: [PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[David Miller]

When you make a new postings of a patch, you must resend the entire
series, not just the patch which is being updated.

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[David Miller]

When you make a new postings of a patch, you must resend the entire
series, not just the patch which is being updated.

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   31 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  186 +++++++++++++++++++++++++++
 5 files changed, 224 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 506b024..1c8dc3d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -54,6 +54,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index c0b8789..da1a435 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..628537f
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,31 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Hisilicon devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select PHYLIB
+	select MARVELL_PHY
+	select MFD_SYSCON
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..e4f67ca
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,186 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   31 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  186 +++++++++++++++++++++++++++
 5 files changed, 224 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 506b024..1c8dc3d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -54,6 +54,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index c0b8789..da1a435 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..628537f
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,31 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Hisilicon devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select PHYLIB
+	select MARVELL_PHY
+	select MFD_SYSCON
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..e4f67ca
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,186 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

Re: [PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[David Miller]

From: zhangfei <zhangfei.gao@linaro.org>
Date: Fri, 04 Apr 2014 23:40:24 +0800

> Thanks Daivd, could I update following this thread first.

You will need to address my feedback, as well as that which anyone
else reviewing this series gives to you.

It is not acceptable, ever, to "just fix it later".  You must fix
all issues pointed out to you before your code will be integrated.

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[David Miller]

From: zhangfei <zhangfei.gao@linaro.org>
Date: Fri, 04 Apr 2014 23:40:24 +0800

> Thanks Daivd, could I update following this thread first.

You will need to address my feedback, as well as that which anyone
else reviewing this series gives to you.

It is not acceptable, ever, to "just fix it later".  You must fix
all issues pointed out to you before your code will be integrated.

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   31 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  186 +++++++++++++++++++++++++++
 5 files changed, 224 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 506b024..1c8dc3d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -54,6 +54,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index c0b8789..da1a435 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..628537f
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,31 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Hisilicon devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select PHYLIB
+	select MARVELL_PHY
+	select MFD_SYSCON
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..e4f67ca
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,186 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   31 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  186 +++++++++++++++++++++++++++
 5 files changed, 224 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 506b024..1c8dc3d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -54,6 +54,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index c0b8789..da1a435 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..628537f
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,31 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Hisilicon devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select PHYLIB
+	select MARVELL_PHY
+	select MFD_SYSCON
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..e4f67ca
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,186 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

Re: [PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[zhangfei]

On 04/04/2014 11:30 PM, David Miller wrote:
> From: Zhangfei Gao <zhangfei.gao@linaro.org>
> Date: Fri,  4 Apr 2014 23:16:36 +0800
>
>> +config HIP04_ETH
>> +	tristate "HISILICON P04 Ethernet support"
>> +	select NET_CORE
>> +	select PHYLIB
>> +	select MARVELL_PHY
>> +	select MFD_SYSCON
>> +	---help---
>> +	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
>> +	  want to use the internal ethernet then you should answer Y to this.
>
> Selecting NET_CORE makes no sense, if it's not set this driver's
> Kconfig file won't even be considered.
>

Thanks Daivd, could I update following this thread first.

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[zhangfei]

On 04/04/2014 11:30 PM, David Miller wrote:
> From: Zhangfei Gao <zhangfei.gao@linaro.org>
> Date: Fri,  4 Apr 2014 23:16:36 +0800
>
>> +config HIP04_ETH
>> +	tristate "HISILICON P04 Ethernet support"
>> +	select NET_CORE
>> +	select PHYLIB
>> +	select MARVELL_PHY
>> +	select MFD_SYSCON
>> +	---help---
>> +	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
>> +	  want to use the internal ethernet then you should answer Y to this.
>
> Selecting NET_CORE makes no sense, if it's not set this driver's
> Kconfig file won't even be considered.
>

Thanks Daivd, could I update following this thread first.

Re: [PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[David Miller]

From: Zhangfei Gao <zhangfei.gao@linaro.org>
Date: Fri,  4 Apr 2014 23:16:36 +0800

> +config HIP04_ETH
> +	tristate "HISILICON P04 Ethernet support"
> +	select NET_CORE
> +	select PHYLIB
> +	select MARVELL_PHY
> +	select MFD_SYSCON
> +	---help---
> +	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
> +	  want to use the internal ethernet then you should answer Y to this.

Selecting NET_CORE makes no sense, if it's not set this driver's
Kconfig file won't even be considered.

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[David Miller]

From: Zhangfei Gao <zhangfei.gao@linaro.org>
Date: Fri,  4 Apr 2014 23:16:36 +0800

> +config HIP04_ETH
> +	tristate "HISILICON P04 Ethernet support"
> +	select NET_CORE
> +	select PHYLIB
> +	select MARVELL_PHY
> +	select MFD_SYSCON
> +	---help---
> +	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
> +	  want to use the internal ethernet then you should answer Y to this.

Selecting NET_CORE makes no sense, if it's not set this driver's
Kconfig file won't even be considered.

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   32 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  186 +++++++++++++++++++++++++++
 5 files changed, 225 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 506b024..1c8dc3d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -54,6 +54,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index c0b8789..da1a435 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..39b5c7e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,32 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Hisilicon devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select NET_CORE
+	select PHYLIB
+	select MARVELL_PHY
+	select MFD_SYSCON
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..e4f67ca
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,186 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   32 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  186 +++++++++++++++++++++++++++
 5 files changed, 225 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 506b024..1c8dc3d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -54,6 +54,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index c0b8789..da1a435 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..39b5c7e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,32 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Hisilicon devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select NET_CORE
+	select PHYLIB
+	select MARVELL_PHY
+	select MFD_SYSCON
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..e4f67ca
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,186 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   32 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  186 +++++++++++++++++++++++++++
 5 files changed, 225 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 506b024..1c8dc3d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -54,6 +54,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index c0b8789..da1a435 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..39b5c7e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,32 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Hisilicon devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select NET_CORE
+	select PHYLIB
+	select MARVELL_PHY
+	select MFD_SYSCON
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..e4f67ca
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,186 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   32 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  186 +++++++++++++++++++++++++++
 5 files changed, 225 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 506b024..1c8dc3d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -54,6 +54,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index c0b8789..da1a435 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..39b5c7e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,32 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Hisilicon devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select NET_CORE
+	select PHYLIB
+	select MARVELL_PHY
+	select MFD_SYSCON
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..e4f67ca
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,186 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   32 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  186 +++++++++++++++++++++++++++
 5 files changed, 225 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 506b024..1c8dc3d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -54,6 +54,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index c0b8789..da1a435 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..b0ee739
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,32 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about MOXA ART devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select NET_CORE
+	select PHYLIB
+	select MARVELL_PHY
+	select MFD_SYSCON
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..e4f67ca
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,186 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   32 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  186 +++++++++++++++++++++++++++
 5 files changed, 225 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 506b024..1c8dc3d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -54,6 +54,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index c0b8789..da1a435 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..b0ee739
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,32 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about MOXA ART devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select NET_CORE
+	select PHYLIB
+	select MARVELL_PHY
+	select MFD_SYSCON
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..e4f67ca
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,186 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   31 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  186 +++++++++++++++++++++++++++
 5 files changed, 224 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 506b024..1c8dc3d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -54,6 +54,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index c0b8789..da1a435 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..4b1c065
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,31 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about MOXA ART devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select NET_CORE
+	select PHYLIB
+	select MARVELL_PHY
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..e4f67ca
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,186 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   31 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  186 +++++++++++++++++++++++++++
 5 files changed, 224 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 506b024..1c8dc3d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -54,6 +54,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index c0b8789..da1a435 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..4b1c065
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,31 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about MOXA ART devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select NET_CORE
+	select PHYLIB
+	select MARVELL_PHY
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..e4f67ca
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,186 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(priv->base)) {
+		ret = PTR_ERR(priv->base);
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

Re: [PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

On Fri, Mar 21, 2014 at 1:59 AM, Florian Fainelli <f.fainelli@gmail.com> wrote:
> 2014-03-20 3:53 GMT-07:00 Zhangfei Gao <zhangfei.gao@gmail.com>:
>>>> +static int hip04_mdio_reset(struct mii_bus *bus)
>>>> +{
>>>> +       int temp, err, i;
>>>> +
>>>> +       for (i = 0; i < 2; i++) {
>>>> +               hip04_mdio_write(bus, i, 22, 0);
>>>> +               temp = hip04_mdio_read(bus, i, MII_BMCR);
>>>> +               temp |= BMCR_RESET;
>>>> +               err = hip04_mdio_write(bus, i, MII_BMCR, temp);
>>>> +               if (err < 0)
>>>> +                       return err;
>>>> +       }
>>>> +
>>>> +       mdelay(500);
>>>
>>> This does not look correct, you should iterate over all possible PHYs:
>>> PHY_MAX_ADDR instead of hardcoding the loop to 2.
>>
>> OK, got it.
>> Use 2 is since only have 2 phy in the board, will use PHY_MAX_ADDR instead.
>>>
>>> I think we might want to remove the mdio bus reset callback in general
>>> as the PHY library should already take care of software resetting the
>>> PHY to put it in a sane state, as well as waiting for the appropriate
>>> delay before using, unlike here, where you do not poll for BMCR_RESET
>>> to be cleared by the PHY.
>>>
>> Do you mean will move BMCR_RESET to common code, that's would be great.
>> The mdio_reset is added here to get phy_id, otherwise the phy_id can
>> not be read as well as detection.
>
> Oh I see, thanks for mentioning that, this is not properly covered
> here today as we need to get the PHY id before we assign it a
> phy_device structure, let me cook a patch for this.
> --

Should I keep hip04_mdio_reset in the next submit or remove it directly?

Thanks

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

On Fri, Mar 21, 2014 at 1:59 AM, Florian Fainelli <f.fainelli@gmail.com> wrote:
> 2014-03-20 3:53 GMT-07:00 Zhangfei Gao <zhangfei.gao@gmail.com>:
>>>> +static int hip04_mdio_reset(struct mii_bus *bus)
>>>> +{
>>>> +       int temp, err, i;
>>>> +
>>>> +       for (i = 0; i < 2; i++) {
>>>> +               hip04_mdio_write(bus, i, 22, 0);
>>>> +               temp = hip04_mdio_read(bus, i, MII_BMCR);
>>>> +               temp |= BMCR_RESET;
>>>> +               err = hip04_mdio_write(bus, i, MII_BMCR, temp);
>>>> +               if (err < 0)
>>>> +                       return err;
>>>> +       }
>>>> +
>>>> +       mdelay(500);
>>>
>>> This does not look correct, you should iterate over all possible PHYs:
>>> PHY_MAX_ADDR instead of hardcoding the loop to 2.
>>
>> OK, got it.
>> Use 2 is since only have 2 phy in the board, will use PHY_MAX_ADDR instead.
>>>
>>> I think we might want to remove the mdio bus reset callback in general
>>> as the PHY library should already take care of software resetting the
>>> PHY to put it in a sane state, as well as waiting for the appropriate
>>> delay before using, unlike here, where you do not poll for BMCR_RESET
>>> to be cleared by the PHY.
>>>
>> Do you mean will move BMCR_RESET to common code, that's would be great.
>> The mdio_reset is added here to get phy_id, otherwise the phy_id can
>> not be read as well as detection.
>
> Oh I see, thanks for mentioning that, this is not properly covered
> here today as we need to get the PHY id before we assign it a
> phy_device structure, let me cook a patch for this.
> --

Should I keep hip04_mdio_reset in the next submit or remove it directly?

Thanks

Re: [PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Florian Fainelli]

2014-03-20 3:53 GMT-07:00 Zhangfei Gao <zhangfei.gao@gmail.com>:
> Dear Florian
>
> On Wed, Mar 19, 2014 at 1:28 AM, Florian Fainelli <f.fainelli@gmail.com> wrote:
>> 2014-03-18 1:40 GMT-07:00 Zhangfei Gao <zhangfei.gao@linaro.org>:
>
>>> +static int hip04_mdio_reset(struct mii_bus *bus)
>>> +{
>>> +       int temp, err, i;
>>> +
>>> +       for (i = 0; i < 2; i++) {
>>> +               hip04_mdio_write(bus, i, 22, 0);
>>> +               temp = hip04_mdio_read(bus, i, MII_BMCR);
>>> +               temp |= BMCR_RESET;
>>> +               err = hip04_mdio_write(bus, i, MII_BMCR, temp);
>>> +               if (err < 0)
>>> +                       return err;
>>> +       }
>>> +
>>> +       mdelay(500);
>>
>> This does not look correct, you should iterate over all possible PHYs:
>> PHY_MAX_ADDR instead of hardcoding the loop to 2.
>
> OK, got it.
> Use 2 is since only have 2 phy in the board, will use PHY_MAX_ADDR instead.
>>
>> I think we might want to remove the mdio bus reset callback in general
>> as the PHY library should already take care of software resetting the
>> PHY to put it in a sane state, as well as waiting for the appropriate
>> delay before using, unlike here, where you do not poll for BMCR_RESET
>> to be cleared by the PHY.
>>
> Do you mean will move BMCR_RESET to common code, that's would be great.
> The mdio_reset is added here to get phy_id, otherwise the phy_id can
> not be read as well as detection.

Oh I see, thanks for mentioning that, this is not properly covered
here today as we need to get the PHY id before we assign it a
phy_device structure, let me cook a patch for this.
-- 
Florian

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Florian Fainelli]

2014-03-20 3:53 GMT-07:00 Zhangfei Gao <zhangfei.gao@gmail.com>:
> Dear Florian
>
> On Wed, Mar 19, 2014 at 1:28 AM, Florian Fainelli <f.fainelli@gmail.com> wrote:
>> 2014-03-18 1:40 GMT-07:00 Zhangfei Gao <zhangfei.gao@linaro.org>:
>
>>> +static int hip04_mdio_reset(struct mii_bus *bus)
>>> +{
>>> +       int temp, err, i;
>>> +
>>> +       for (i = 0; i < 2; i++) {
>>> +               hip04_mdio_write(bus, i, 22, 0);
>>> +               temp = hip04_mdio_read(bus, i, MII_BMCR);
>>> +               temp |= BMCR_RESET;
>>> +               err = hip04_mdio_write(bus, i, MII_BMCR, temp);
>>> +               if (err < 0)
>>> +                       return err;
>>> +       }
>>> +
>>> +       mdelay(500);
>>
>> This does not look correct, you should iterate over all possible PHYs:
>> PHY_MAX_ADDR instead of hardcoding the loop to 2.
>
> OK, got it.
> Use 2 is since only have 2 phy in the board, will use PHY_MAX_ADDR instead.
>>
>> I think we might want to remove the mdio bus reset callback in general
>> as the PHY library should already take care of software resetting the
>> PHY to put it in a sane state, as well as waiting for the appropriate
>> delay before using, unlike here, where you do not poll for BMCR_RESET
>> to be cleared by the PHY.
>>
> Do you mean will move BMCR_RESET to common code, that's would be great.
> The mdio_reset is added here to get phy_id, otherwise the phy_id can
> not be read as well as detection.

Oh I see, thanks for mentioning that, this is not properly covered
here today as we need to get the PHY id before we assign it a
phy_device structure, let me cook a patch for this.
-- 
Florian

Re: [PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Dear Florian

On Wed, Mar 19, 2014 at 1:28 AM, Florian Fainelli <f.fainelli@gmail.com> wrote:
> 2014-03-18 1:40 GMT-07:00 Zhangfei Gao <zhangfei.gao@linaro.org>:

>> +static int hip04_mdio_reset(struct mii_bus *bus)
>> +{
>> +       int temp, err, i;
>> +
>> +       for (i = 0; i < 2; i++) {
>> +               hip04_mdio_write(bus, i, 22, 0);
>> +               temp = hip04_mdio_read(bus, i, MII_BMCR);
>> +               temp |= BMCR_RESET;
>> +               err = hip04_mdio_write(bus, i, MII_BMCR, temp);
>> +               if (err < 0)
>> +                       return err;
>> +       }
>> +
>> +       mdelay(500);
>
> This does not look correct, you should iterate over all possible PHYs:
> PHY_MAX_ADDR instead of hardcoding the loop to 2.

OK, got it.
Use 2 is since only have 2 phy in the board, will use PHY_MAX_ADDR instead.
>
> I think we might want to remove the mdio bus reset callback in general
> as the PHY library should already take care of software resetting the
> PHY to put it in a sane state, as well as waiting for the appropriate
> delay before using, unlike here, where you do not poll for BMCR_RESET
> to be cleared by the PHY.
>
Do you mean will move BMCR_RESET to common code, that's would be great.
The mdio_reset is added here to get phy_id, otherwise the phy_id can
not be read as well as detection.

Thanks

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Dear Florian

On Wed, Mar 19, 2014 at 1:28 AM, Florian Fainelli <f.fainelli@gmail.com> wrote:
> 2014-03-18 1:40 GMT-07:00 Zhangfei Gao <zhangfei.gao@linaro.org>:

>> +static int hip04_mdio_reset(struct mii_bus *bus)
>> +{
>> +       int temp, err, i;
>> +
>> +       for (i = 0; i < 2; i++) {
>> +               hip04_mdio_write(bus, i, 22, 0);
>> +               temp = hip04_mdio_read(bus, i, MII_BMCR);
>> +               temp |= BMCR_RESET;
>> +               err = hip04_mdio_write(bus, i, MII_BMCR, temp);
>> +               if (err < 0)
>> +                       return err;
>> +       }
>> +
>> +       mdelay(500);
>
> This does not look correct, you should iterate over all possible PHYs:
> PHY_MAX_ADDR instead of hardcoding the loop to 2.

OK, got it.
Use 2 is since only have 2 phy in the board, will use PHY_MAX_ADDR instead.
>
> I think we might want to remove the mdio bus reset callback in general
> as the PHY library should already take care of software resetting the
> PHY to put it in a sane state, as well as waiting for the appropriate
> delay before using, unlike here, where you do not poll for BMCR_RESET
> to be cleared by the PHY.
>
Do you mean will move BMCR_RESET to common code, that's would be great.
The mdio_reset is added here to get phy_id, otherwise the phy_id can
not be read as well as detection.

Thanks

Re: [PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Florian Fainelli]

2014-03-18 1:40 GMT-07:00 Zhangfei Gao <zhangfei.gao-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>:
> Hisilicon hip04 platform mdio driver
> Reuse Marvell phy drivers/net/phy/marvell.c
>
> Signed-off-by: Zhangfei Gao <zhangfei.gao-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> ---
>  drivers/net/ethernet/Kconfig                |    1 +
>  drivers/net/ethernet/Makefile               |    1 +
>  drivers/net/ethernet/hisilicon/Kconfig      |   31 +++++
>  drivers/net/ethernet/hisilicon/Makefile     |    5 +
>  drivers/net/ethernet/hisilicon/hip04_mdio.c |  190 +++++++++++++++++++++++++++
>  5 files changed, 228 insertions(+)
>  create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
>  create mode 100644 drivers/net/ethernet/hisilicon/Makefile
>  create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c
>
> diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
> index 39484b5..cef103d 100644
> --- a/drivers/net/ethernet/Kconfig
> +++ b/drivers/net/ethernet/Kconfig
> @@ -55,6 +55,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
>  source "drivers/net/ethernet/faraday/Kconfig"
>  source "drivers/net/ethernet/freescale/Kconfig"
>  source "drivers/net/ethernet/fujitsu/Kconfig"
> +source "drivers/net/ethernet/hisilicon/Kconfig"
>  source "drivers/net/ethernet/hp/Kconfig"
>  source "drivers/net/ethernet/ibm/Kconfig"
>  source "drivers/net/ethernet/intel/Kconfig"
> diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
> index adf61af..f70b166 100644
> --- a/drivers/net/ethernet/Makefile
> +++ b/drivers/net/ethernet/Makefile
> @@ -30,6 +30,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
>  obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
>  obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
>  obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
> +obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
>  obj-$(CONFIG_NET_VENDOR_HP) += hp/
>  obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
>  obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
> diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
> new file mode 100644
> index 0000000..4b1c065
> --- /dev/null
> +++ b/drivers/net/ethernet/hisilicon/Kconfig
> @@ -0,0 +1,31 @@
> +#
> +# HISILICON device configuration
> +#
> +
> +config NET_VENDOR_HISILICON
> +       bool "Hisilicon devices"
> +       default y
> +       depends on ARM
> +       ---help---
> +         If you have a network (Ethernet) card belonging to this class, say Y
> +         and read the Ethernet-HOWTO, available from
> +         <http://www.tldp.org/docs.html#howto>.
> +
> +         Note that the answer to this question doesn't directly affect the
> +         kernel: saying N will just cause the configurator to skip all
> +         the questions about MOXA ART devices. If you say Y, you will be asked
> +         for your specific card in the following questions.
> +
> +if NET_VENDOR_HISILICON
> +
> +config HIP04_ETH
> +       tristate "HISILICON P04 Ethernet support"
> +       select NET_CORE
> +       select PHYLIB
> +       select MARVELL_PHY
> +       ---help---
> +         If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
> +         want to use the internal ethernet then you should answer Y to this.
> +
> +
> +endif # NET_VENDOR_HISILICON
> diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
> new file mode 100644
> index 0000000..1d6eb6e
> --- /dev/null
> +++ b/drivers/net/ethernet/hisilicon/Makefile
> @@ -0,0 +1,5 @@
> +#
> +# Makefile for the HISILICON network device drivers.
> +#
> +
> +obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
> diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
> new file mode 100644
> index 0000000..960adc2
> --- /dev/null
> +++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
> @@ -0,0 +1,190 @@
> +
> +/* Copyright (c) 2014 Linaro Ltd.
> + * Copyright (c) 2014 Hisilicon Limited.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/io.h>
> +#include <linux/of_mdio.h>
> +#include <linux/delay.h>
> +
> +#define MDIO_CMD_REG           0x0
> +#define MDIO_ADDR_REG          0x4
> +#define MDIO_WDATA_REG         0x8
> +#define MDIO_RDATA_REG         0xc
> +#define MDIO_STA_REG           0x10
> +
> +#define MDIO_START             BIT(14)
> +#define MDIO_R_VALID           BIT(1)
> +#define MDIO_READ              (BIT(12) | BIT(11) | MDIO_START)
> +#define MDIO_WRITE             (BIT(12) | BIT(10) | MDIO_START)
> +
> +struct hip04_mdio_priv {
> +       void __iomem *base;
> +};
> +
> +#define WAIT_TIMEOUT 10
> +static int hip04_mdio_wait_ready(struct mii_bus *bus)
> +{
> +       struct hip04_mdio_priv *priv = bus->priv;
> +       int i;
> +
> +       for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
> +               if (i == WAIT_TIMEOUT)
> +                       return -ETIMEDOUT;
> +               msleep(20);
> +       }
> +
> +       return 0;
> +}
> +
> +static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
> +{
> +       struct hip04_mdio_priv *priv = bus->priv;
> +       u32 val;
> +       int ret;
> +
> +       ret = hip04_mdio_wait_ready(bus);
> +       if (ret < 0)
> +               goto out;
> +
> +       val = regnum | (mii_id << 5) | MDIO_READ;
> +       writel_relaxed(val, priv->base + MDIO_CMD_REG);
> +
> +       ret = hip04_mdio_wait_ready(bus);
> +       if (ret < 0)
> +               goto out;
> +       val = readl_relaxed(priv->base + MDIO_STA_REG);
> +       if (val & MDIO_R_VALID) {
> +               dev_err(bus->parent, "SMI bus read not valid\n");
> +               ret = -ENODEV;
> +               goto out;
> +       }
> +       val = readl_relaxed(priv->base + MDIO_RDATA_REG);
> +       ret = val & 0xFFFF;
> +out:
> +       return ret;
> +}
> +
> +static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
> +                           int regnum, u16 value)
> +{
> +       struct hip04_mdio_priv *priv = bus->priv;
> +       u32 val;
> +       int ret;
> +
> +       ret = hip04_mdio_wait_ready(bus);
> +       if (ret < 0)
> +               goto out;
> +
> +       writel_relaxed(value, priv->base + MDIO_WDATA_REG);
> +       val = regnum | (mii_id << 5) | MDIO_WRITE;
> +       writel_relaxed(val, priv->base + MDIO_CMD_REG);
> +out:
> +       return ret;
> +}
> +
> +
> +static int hip04_mdio_reset(struct mii_bus *bus)
> +{
> +       int temp, err, i;
> +
> +       for (i = 0; i < 2; i++) {
> +               hip04_mdio_write(bus, i, 22, 0);
> +               temp = hip04_mdio_read(bus, i, MII_BMCR);
> +               temp |= BMCR_RESET;
> +               err = hip04_mdio_write(bus, i, MII_BMCR, temp);
> +               if (err < 0)
> +                       return err;
> +       }
> +
> +       mdelay(500);

This does not look correct, you should iterate over all possible PHYs:
PHY_MAX_ADDR instead of hardcoding the loop to 2.

I think we might want to remove the mdio bus reset callback in general
as the PHY library should already take care of software resetting the
PHY to put it in a sane state, as well as waiting for the appropriate
delay before using, unlike here, where you do not poll for BMCR_RESET
to be cleared by the PHY.

> +       return 0;
> +}
> +
> +static int hip04_mdio_probe(struct platform_device *pdev)
> +{
> +       struct resource *r;
> +       struct mii_bus *bus;
> +       struct hip04_mdio_priv *priv;
> +       int ret;
> +
> +       r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +       if (!r) {
> +               dev_err(&pdev->dev, "No SMI register address given\n");
> +               return -ENODEV;
> +       }
> +
> +       bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
> +       if (!bus) {
> +               dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
> +               return -ENOMEM;
> +       }
> +
> +       bus->name = "hip04_mdio_bus";
> +       bus->read = hip04_mdio_read;
> +       bus->write = hip04_mdio_write;
> +       bus->reset = hip04_mdio_reset;
> +       snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii",
> +                dev_name(&pdev->dev));
> +       bus->parent = &pdev->dev;
> +       priv = bus->priv;
> +       priv->base = devm_ioremap(&pdev->dev, r->start, resource_size(r));
> +       if (!priv->base) {
> +               dev_err(&pdev->dev, "Unable to remap SMI register\n");
> +               ret = -ENODEV;
> +               goto out_mdio;
> +       }
> +
> +       ret = of_mdiobus_register(bus, pdev->dev.of_node);
> +       if (ret < 0) {
> +               dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
> +               goto out_mdio;
> +       }
> +
> +       platform_set_drvdata(pdev, bus);
> +
> +       return 0;
> +
> +out_mdio:
> +       mdiobus_free(bus);
> +       return ret;
> +}
> +
> +static int hip04_mdio_remove(struct platform_device *pdev)
> +{
> +       struct mii_bus *bus = platform_get_drvdata(pdev);
> +
> +       mdiobus_unregister(bus);
> +       mdiobus_free(bus);
> +
> +       return 0;
> +}
> +
> +static const struct of_device_id hip04_mdio_match[] = {
> +       { .compatible = "hisilicon,hip04-mdio" },
> +       { }
> +};
> +MODULE_DEVICE_TABLE(of, hip04_mdio_match);
> +
> +static struct platform_driver hip04_mdio_driver = {
> +       .probe = hip04_mdio_probe,
> +       .remove = hip04_mdio_remove,
> +       .driver = {
> +               .name = "hip04-mdio",
> +               .owner = THIS_MODULE,
> +               .of_match_table = hip04_mdio_match,
> +       },
> +};
> +
> +module_platform_driver(hip04_mdio_driver);
> +
> +MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
> +MODULE_LICENSE("GPL v2");
> +MODULE_ALIAS("platform:hip04-mdio");
> --
> 1.7.9.5
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel



-- 
Florian
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Florian Fainelli]

2014-03-18 1:40 GMT-07:00 Zhangfei Gao <zhangfei.gao@linaro.org>:
> Hisilicon hip04 platform mdio driver
> Reuse Marvell phy drivers/net/phy/marvell.c
>
> Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
> ---
>  drivers/net/ethernet/Kconfig                |    1 +
>  drivers/net/ethernet/Makefile               |    1 +
>  drivers/net/ethernet/hisilicon/Kconfig      |   31 +++++
>  drivers/net/ethernet/hisilicon/Makefile     |    5 +
>  drivers/net/ethernet/hisilicon/hip04_mdio.c |  190 +++++++++++++++++++++++++++
>  5 files changed, 228 insertions(+)
>  create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
>  create mode 100644 drivers/net/ethernet/hisilicon/Makefile
>  create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c
>
> diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
> index 39484b5..cef103d 100644
> --- a/drivers/net/ethernet/Kconfig
> +++ b/drivers/net/ethernet/Kconfig
> @@ -55,6 +55,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
>  source "drivers/net/ethernet/faraday/Kconfig"
>  source "drivers/net/ethernet/freescale/Kconfig"
>  source "drivers/net/ethernet/fujitsu/Kconfig"
> +source "drivers/net/ethernet/hisilicon/Kconfig"
>  source "drivers/net/ethernet/hp/Kconfig"
>  source "drivers/net/ethernet/ibm/Kconfig"
>  source "drivers/net/ethernet/intel/Kconfig"
> diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
> index adf61af..f70b166 100644
> --- a/drivers/net/ethernet/Makefile
> +++ b/drivers/net/ethernet/Makefile
> @@ -30,6 +30,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
>  obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
>  obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
>  obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
> +obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
>  obj-$(CONFIG_NET_VENDOR_HP) += hp/
>  obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
>  obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
> diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
> new file mode 100644
> index 0000000..4b1c065
> --- /dev/null
> +++ b/drivers/net/ethernet/hisilicon/Kconfig
> @@ -0,0 +1,31 @@
> +#
> +# HISILICON device configuration
> +#
> +
> +config NET_VENDOR_HISILICON
> +       bool "Hisilicon devices"
> +       default y
> +       depends on ARM
> +       ---help---
> +         If you have a network (Ethernet) card belonging to this class, say Y
> +         and read the Ethernet-HOWTO, available from
> +         <http://www.tldp.org/docs.html#howto>.
> +
> +         Note that the answer to this question doesn't directly affect the
> +         kernel: saying N will just cause the configurator to skip all
> +         the questions about MOXA ART devices. If you say Y, you will be asked
> +         for your specific card in the following questions.
> +
> +if NET_VENDOR_HISILICON
> +
> +config HIP04_ETH
> +       tristate "HISILICON P04 Ethernet support"
> +       select NET_CORE
> +       select PHYLIB
> +       select MARVELL_PHY
> +       ---help---
> +         If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
> +         want to use the internal ethernet then you should answer Y to this.
> +
> +
> +endif # NET_VENDOR_HISILICON
> diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
> new file mode 100644
> index 0000000..1d6eb6e
> --- /dev/null
> +++ b/drivers/net/ethernet/hisilicon/Makefile
> @@ -0,0 +1,5 @@
> +#
> +# Makefile for the HISILICON network device drivers.
> +#
> +
> +obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
> diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
> new file mode 100644
> index 0000000..960adc2
> --- /dev/null
> +++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
> @@ -0,0 +1,190 @@
> +
> +/* Copyright (c) 2014 Linaro Ltd.
> + * Copyright (c) 2014 Hisilicon Limited.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/io.h>
> +#include <linux/of_mdio.h>
> +#include <linux/delay.h>
> +
> +#define MDIO_CMD_REG           0x0
> +#define MDIO_ADDR_REG          0x4
> +#define MDIO_WDATA_REG         0x8
> +#define MDIO_RDATA_REG         0xc
> +#define MDIO_STA_REG           0x10
> +
> +#define MDIO_START             BIT(14)
> +#define MDIO_R_VALID           BIT(1)
> +#define MDIO_READ              (BIT(12) | BIT(11) | MDIO_START)
> +#define MDIO_WRITE             (BIT(12) | BIT(10) | MDIO_START)
> +
> +struct hip04_mdio_priv {
> +       void __iomem *base;
> +};
> +
> +#define WAIT_TIMEOUT 10
> +static int hip04_mdio_wait_ready(struct mii_bus *bus)
> +{
> +       struct hip04_mdio_priv *priv = bus->priv;
> +       int i;
> +
> +       for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
> +               if (i == WAIT_TIMEOUT)
> +                       return -ETIMEDOUT;
> +               msleep(20);
> +       }
> +
> +       return 0;
> +}
> +
> +static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
> +{
> +       struct hip04_mdio_priv *priv = bus->priv;
> +       u32 val;
> +       int ret;
> +
> +       ret = hip04_mdio_wait_ready(bus);
> +       if (ret < 0)
> +               goto out;
> +
> +       val = regnum | (mii_id << 5) | MDIO_READ;
> +       writel_relaxed(val, priv->base + MDIO_CMD_REG);
> +
> +       ret = hip04_mdio_wait_ready(bus);
> +       if (ret < 0)
> +               goto out;
> +       val = readl_relaxed(priv->base + MDIO_STA_REG);
> +       if (val & MDIO_R_VALID) {
> +               dev_err(bus->parent, "SMI bus read not valid\n");
> +               ret = -ENODEV;
> +               goto out;
> +       }
> +       val = readl_relaxed(priv->base + MDIO_RDATA_REG);
> +       ret = val & 0xFFFF;
> +out:
> +       return ret;
> +}
> +
> +static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
> +                           int regnum, u16 value)
> +{
> +       struct hip04_mdio_priv *priv = bus->priv;
> +       u32 val;
> +       int ret;
> +
> +       ret = hip04_mdio_wait_ready(bus);
> +       if (ret < 0)
> +               goto out;
> +
> +       writel_relaxed(value, priv->base + MDIO_WDATA_REG);
> +       val = regnum | (mii_id << 5) | MDIO_WRITE;
> +       writel_relaxed(val, priv->base + MDIO_CMD_REG);
> +out:
> +       return ret;
> +}
> +
> +
> +static int hip04_mdio_reset(struct mii_bus *bus)
> +{
> +       int temp, err, i;
> +
> +       for (i = 0; i < 2; i++) {
> +               hip04_mdio_write(bus, i, 22, 0);
> +               temp = hip04_mdio_read(bus, i, MII_BMCR);
> +               temp |= BMCR_RESET;
> +               err = hip04_mdio_write(bus, i, MII_BMCR, temp);
> +               if (err < 0)
> +                       return err;
> +       }
> +
> +       mdelay(500);

This does not look correct, you should iterate over all possible PHYs:
PHY_MAX_ADDR instead of hardcoding the loop to 2.

I think we might want to remove the mdio bus reset callback in general
as the PHY library should already take care of software resetting the
PHY to put it in a sane state, as well as waiting for the appropriate
delay before using, unlike here, where you do not poll for BMCR_RESET
to be cleared by the PHY.

> +       return 0;
> +}
> +
> +static int hip04_mdio_probe(struct platform_device *pdev)
> +{
> +       struct resource *r;
> +       struct mii_bus *bus;
> +       struct hip04_mdio_priv *priv;
> +       int ret;
> +
> +       r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +       if (!r) {
> +               dev_err(&pdev->dev, "No SMI register address given\n");
> +               return -ENODEV;
> +       }
> +
> +       bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
> +       if (!bus) {
> +               dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
> +               return -ENOMEM;
> +       }
> +
> +       bus->name = "hip04_mdio_bus";
> +       bus->read = hip04_mdio_read;
> +       bus->write = hip04_mdio_write;
> +       bus->reset = hip04_mdio_reset;
> +       snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii",
> +                dev_name(&pdev->dev));
> +       bus->parent = &pdev->dev;
> +       priv = bus->priv;
> +       priv->base = devm_ioremap(&pdev->dev, r->start, resource_size(r));
> +       if (!priv->base) {
> +               dev_err(&pdev->dev, "Unable to remap SMI register\n");
> +               ret = -ENODEV;
> +               goto out_mdio;
> +       }
> +
> +       ret = of_mdiobus_register(bus, pdev->dev.of_node);
> +       if (ret < 0) {
> +               dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
> +               goto out_mdio;
> +       }
> +
> +       platform_set_drvdata(pdev, bus);
> +
> +       return 0;
> +
> +out_mdio:
> +       mdiobus_free(bus);
> +       return ret;
> +}
> +
> +static int hip04_mdio_remove(struct platform_device *pdev)
> +{
> +       struct mii_bus *bus = platform_get_drvdata(pdev);
> +
> +       mdiobus_unregister(bus);
> +       mdiobus_free(bus);
> +
> +       return 0;
> +}
> +
> +static const struct of_device_id hip04_mdio_match[] = {
> +       { .compatible = "hisilicon,hip04-mdio" },
> +       { }
> +};
> +MODULE_DEVICE_TABLE(of, hip04_mdio_match);
> +
> +static struct platform_driver hip04_mdio_driver = {
> +       .probe = hip04_mdio_probe,
> +       .remove = hip04_mdio_remove,
> +       .driver = {
> +               .name = "hip04-mdio",
> +               .owner = THIS_MODULE,
> +               .of_match_table = hip04_mdio_match,
> +       },
> +};
> +
> +module_platform_driver(hip04_mdio_driver);
> +
> +MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
> +MODULE_LICENSE("GPL v2");
> +MODULE_ALIAS("platform:hip04-mdio");
> --
> 1.7.9.5
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel



-- 
Florian

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   31 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  190 +++++++++++++++++++++++++++
 5 files changed, 228 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 39484b5..cef103d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -55,6 +55,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index adf61af..f70b166 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -30,6 +30,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..4b1c065
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,31 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about MOXA ART devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select NET_CORE
+	select PHYLIB
+	select MARVELL_PHY
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..960adc2
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,190 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < 2; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!r) {
+		dev_err(&pdev->dev, "No SMI register address given\n");
+		return -ENODEV;
+	}
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii",
+		 dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+	priv->base = devm_ioremap(&pdev->dev, r->start, resource_size(r));
+	if (!priv->base) {
+		dev_err(&pdev->dev, "Unable to remap SMI register\n");
+		ret = -ENODEV;
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5

[PATCH 2/3] net: hisilicon: new hip04 MDIO driver

[Zhangfei Gao]

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/net/ethernet/Kconfig                |    1 +
 drivers/net/ethernet/Makefile               |    1 +
 drivers/net/ethernet/hisilicon/Kconfig      |   31 +++++
 drivers/net/ethernet/hisilicon/Makefile     |    5 +
 drivers/net/ethernet/hisilicon/hip04_mdio.c |  190 +++++++++++++++++++++++++++
 5 files changed, 228 insertions(+)
 create mode 100644 drivers/net/ethernet/hisilicon/Kconfig
 create mode 100644 drivers/net/ethernet/hisilicon/Makefile
 create mode 100644 drivers/net/ethernet/hisilicon/hip04_mdio.c

diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 39484b5..cef103d 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -55,6 +55,7 @@ source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/freescale/Kconfig"
 source "drivers/net/ethernet/fujitsu/Kconfig"
+source "drivers/net/ethernet/hisilicon/Kconfig"
 source "drivers/net/ethernet/hp/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index adf61af..f70b166 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -30,6 +30,7 @@ obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_FREESCALE) += freescale/
 obj-$(CONFIG_NET_VENDOR_FUJITSU) += fujitsu/
+obj-$(CONFIG_NET_VENDOR_HISILICON) += hisilicon/
 obj-$(CONFIG_NET_VENDOR_HP) += hp/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
new file mode 100644
index 0000000..4b1c065
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -0,0 +1,31 @@
+#
+# HISILICON device configuration
+#
+
+config NET_VENDOR_HISILICON
+	bool "Hisilicon devices"
+	default y
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about MOXA ART devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_HISILICON
+
+config HIP04_ETH
+	tristate "HISILICON P04 Ethernet support"
+	select NET_CORE
+	select PHYLIB
+	select MARVELL_PHY
+	---help---
+	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_HISILICON
diff --git a/drivers/net/ethernet/hisilicon/Makefile b/drivers/net/ethernet/hisilicon/Makefile
new file mode 100644
index 0000000..1d6eb6e
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the HISILICON network device drivers.
+#
+
+obj-$(CONFIG_HIP04_ETH) += hip04_mdio.o
diff --git a/drivers/net/ethernet/hisilicon/hip04_mdio.c b/drivers/net/ethernet/hisilicon/hip04_mdio.c
new file mode 100644
index 0000000..960adc2
--- /dev/null
+++ b/drivers/net/ethernet/hisilicon/hip04_mdio.c
@@ -0,0 +1,190 @@
+
+/* Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+
+#define MDIO_CMD_REG		0x0
+#define MDIO_ADDR_REG		0x4
+#define MDIO_WDATA_REG		0x8
+#define MDIO_RDATA_REG		0xc
+#define MDIO_STA_REG		0x10
+
+#define MDIO_START		BIT(14)
+#define MDIO_R_VALID		BIT(1)
+#define MDIO_READ	        (BIT(12) | BIT(11) | MDIO_START)
+#define MDIO_WRITE	        (BIT(12) | BIT(10) | MDIO_START)
+
+struct hip04_mdio_priv {
+	void __iomem *base;
+};
+
+#define WAIT_TIMEOUT 10
+static int hip04_mdio_wait_ready(struct mii_bus *bus)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	int i;
+
+	for (i = 0; readl_relaxed(priv->base + MDIO_CMD_REG) & MDIO_START; i++) {
+		if (i == WAIT_TIMEOUT)
+			return -ETIMEDOUT;
+		msleep(20);
+	}
+
+	return 0;
+}
+
+static int hip04_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	val = regnum | (mii_id << 5) | MDIO_READ;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+	val = readl_relaxed(priv->base + MDIO_STA_REG);
+	if (val & MDIO_R_VALID) {
+		dev_err(bus->parent, "SMI bus read not valid\n");
+		ret = -ENODEV;
+		goto out;
+	}
+	val = readl_relaxed(priv->base + MDIO_RDATA_REG);
+	ret = val & 0xFFFF;
+out:
+	return ret;
+}
+
+static int hip04_mdio_write(struct mii_bus *bus, int mii_id,
+			    int regnum, u16 value)
+{
+	struct hip04_mdio_priv *priv = bus->priv;
+	u32 val;
+	int ret;
+
+	ret = hip04_mdio_wait_ready(bus);
+	if (ret < 0)
+		goto out;
+
+	writel_relaxed(value, priv->base + MDIO_WDATA_REG);
+	val = regnum | (mii_id << 5) | MDIO_WRITE;
+	writel_relaxed(val, priv->base + MDIO_CMD_REG);
+out:
+	return ret;
+}
+
+
+static int hip04_mdio_reset(struct mii_bus *bus)
+{
+	int temp, err, i;
+
+	for (i = 0; i < 2; i++) {
+		hip04_mdio_write(bus, i, 22, 0);
+		temp = hip04_mdio_read(bus, i, MII_BMCR);
+		temp |= BMCR_RESET;
+		err = hip04_mdio_write(bus, i, MII_BMCR, temp);
+		if (err < 0)
+			return err;
+	}
+
+	mdelay(500);
+	return 0;
+}
+
+static int hip04_mdio_probe(struct platform_device *pdev)
+{
+	struct resource *r;
+	struct mii_bus *bus;
+	struct hip04_mdio_priv *priv;
+	int ret;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!r) {
+		dev_err(&pdev->dev, "No SMI register address given\n");
+		return -ENODEV;
+	}
+
+	bus = mdiobus_alloc_size(sizeof(struct hip04_mdio_priv));
+	if (!bus) {
+		dev_err(&pdev->dev, "Cannot allocate MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	bus->name = "hip04_mdio_bus";
+	bus->read = hip04_mdio_read;
+	bus->write = hip04_mdio_write;
+	bus->reset = hip04_mdio_reset;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii",
+		 dev_name(&pdev->dev));
+	bus->parent = &pdev->dev;
+	priv = bus->priv;
+	priv->base = devm_ioremap(&pdev->dev, r->start, resource_size(r));
+	if (!priv->base) {
+		dev_err(&pdev->dev, "Unable to remap SMI register\n");
+		ret = -ENODEV;
+		goto out_mdio;
+	}
+
+	ret = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Cannot register MDIO bus (%d)\n", ret);
+		goto out_mdio;
+	}
+
+	platform_set_drvdata(pdev, bus);
+
+	return 0;
+
+out_mdio:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int hip04_mdio_remove(struct platform_device *pdev)
+{
+	struct mii_bus *bus = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(bus);
+	mdiobus_free(bus);
+
+	return 0;
+}
+
+static const struct of_device_id hip04_mdio_match[] = {
+	{ .compatible = "hisilicon,hip04-mdio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, hip04_mdio_match);
+
+static struct platform_driver hip04_mdio_driver = {
+	.probe = hip04_mdio_probe,
+	.remove = hip04_mdio_remove,
+	.driver = {
+		.name = "hip04-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = hip04_mdio_match,
+	},
+};
+
+module_platform_driver(hip04_mdio_driver);
+
+MODULE_DESCRIPTION("HISILICON P04 MDIO interface driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hip04-mdio");
-- 
1.7.9.5