All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH v3 0/3] ARM: dts: overo: Add panel support
@ 2014-05-20 13:58 ` Florian Vaussard
  0 siblings, 0 replies; 14+ messages in thread
From: Florian Vaussard @ 2014-05-20 13:58 UTC (permalink / raw)
  To: Tony Lindgren; +Cc: Tomi Valkeinen, linux-omap, linux-arm-kernel, devicetree

Hi,

This series enables the DVI and LCD panels present on some of
the Overo expansion boards.

DVI output:
- Tobi
- Summit

LCD (3.5''):
- Alto35

LCD (4.3''):
- Chestnut43
- Palo43
- Gallop43

I tested on Tobi, Alto35 and Gallop43.

This series depends on several patches from Tomi [1][2][3] targeting 3.16.

Regards,
Florian

Since v2:
- Use gpio-backlight
Since v1:
- Rebased on 3.15-rc4 + recent patches from Tomi

[1] http://thread.gmane.org/gmane.linux.ports.arm.omap/114572
[2] http://thread.gmane.org/gmane.linux.ports.arm.omap/114560
[3] http://lists.infradead.org/pipermail/linux-arm-kernel/2014-January/227101.html

Florian Vaussard (3):
  ARM: dts: overo: Add support for DVI output
  ARM: dts: overo: Add support for 4.3'' LCD output
  ARM: dts: overo: Add support for 3.5'' LCD output

 arch/arm/boot/dts/omap3-overo-alto35-common.dtsi   |   1 +
 .../boot/dts/omap3-overo-chestnut43-common.dtsi    |   1 +
 arch/arm/boot/dts/omap3-overo-common-dvi.dtsi      | 111 +++++++++++++
 arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi    | 165 +++++++++++++++++++
 arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi    | 178 +++++++++++++++++++++
 arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi |   1 +
 arch/arm/boot/dts/omap3-overo-palo43-common.dtsi   |   1 +
 arch/arm/boot/dts/omap3-overo-summit-common.dtsi   |   1 +
 arch/arm/boot/dts/omap3-overo-tobi-common.dtsi     |   1 +
 9 files changed, 460 insertions(+)
 create mode 100644 arch/arm/boot/dts/omap3-overo-common-dvi.dtsi
 create mode 100644 arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi
 create mode 100644 arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi

-- 
1.8.3.2


^ permalink raw reply	[flat|nested] 14+ messages in thread
* [PATCH v3 0/3] ARM: dts: overo: Add panel support
@ 2014-05-20 13:58 ` Florian Vaussard
  0 siblings, 0 replies; 14+ messages in thread
From: Florian Vaussard @ 2014-05-20 13:58 UTC (permalink / raw)
  To: linux-arm-kernel

Hi,

This series enables the DVI and LCD panels present on some of
the Overo expansion boards.

DVI output:
- Tobi
- Summit

LCD (3.5''):
- Alto35

LCD (4.3''):
- Chestnut43
- Palo43
- Gallop43

I tested on Tobi, Alto35 and Gallop43.

This series depends on several patches from Tomi [1][2][3] targeting 3.16.

Regards,
Florian

Since v2:
- Use gpio-backlight
Since v1:
- Rebased on 3.15-rc4 + recent patches from Tomi

[1] http://thread.gmane.org/gmane.linux.ports.arm.omap/114572
[2] http://thread.gmane.org/gmane.linux.ports.arm.omap/114560
[3] http://lists.infradead.org/pipermail/linux-arm-kernel/2014-January/227101.html

Florian Vaussard (3):
  ARM: dts: overo: Add support for DVI output
  ARM: dts: overo: Add support for 4.3'' LCD output
  ARM: dts: overo: Add support for 3.5'' LCD output

 arch/arm/boot/dts/omap3-overo-alto35-common.dtsi   |   1 +
 .../boot/dts/omap3-overo-chestnut43-common.dtsi    |   1 +
 arch/arm/boot/dts/omap3-overo-common-dvi.dtsi      | 111 +++++++++++++
 arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi    | 165 +++++++++++++++++++
 arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi    | 178 +++++++++++++++++++++
 arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi |   1 +
 arch/arm/boot/dts/omap3-overo-palo43-common.dtsi   |   1 +
 arch/arm/boot/dts/omap3-overo-summit-common.dtsi   |   1 +
 arch/arm/boot/dts/omap3-overo-tobi-common.dtsi     |   1 +
 9 files changed, 460 insertions(+)
 create mode 100644 arch/arm/boot/dts/omap3-overo-common-dvi.dtsi
 create mode 100644 arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi
 create mode 100644 arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi

-- 
1.8.3.2

^ permalink raw reply	[flat|nested] 14+ messages in thread
* [PATCH v3 1/3] ARM: dts: overo: Add support for DVI output
  2014-05-20 13:58 ` Florian Vaussard
@ 2014-05-20 13:58   ` Florian Vaussard
  -1 siblings, 0 replies; 14+ messages in thread
From: Florian Vaussard @ 2014-05-20 13:58 UTC (permalink / raw)
  To: Tony Lindgren; +Cc: Tomi Valkeinen, linux-omap, linux-arm-kernel, devicetree

Summit and Tobi expansion boards have a HDMI connector with a TFP410
encoder. Add a common include file for this configuration, and then
use it for Summit and Tobi.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
---
 arch/arm/boot/dts/omap3-overo-common-dvi.dtsi    | 111 +++++++++++++++++++++++
 arch/arm/boot/dts/omap3-overo-summit-common.dtsi |   1 +
 arch/arm/boot/dts/omap3-overo-tobi-common.dtsi   |   1 +
 3 files changed, 113 insertions(+)
 create mode 100644 arch/arm/boot/dts/omap3-overo-common-dvi.dtsi

diff --git a/arch/arm/boot/dts/omap3-overo-common-dvi.dtsi b/arch/arm/boot/dts/omap3-overo-common-dvi.dtsi
new file mode 100644
index 0000000..802f704
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-overo-common-dvi.dtsi
@@ -0,0 +1,111 @@
+/*
+ * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * DVI output for some Gumstix Overo boards (Tobi and Summit)
+ */
+
+&omap3_pmx_core {
+	dss_dpi_pins: pinmux_dss_dpi_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)	/* dss_pclk.dss_pclk */
+			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)	/* dss_hsync.dss_hsync */
+			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0)	/* dss_vsync.dss_vsync */
+			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0)	/* dss_acbias.dss_acbias */
+			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0)	/* dss_data0.dss_data0 */
+			OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0)	/* dss_data1.dss_data1 */
+			OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0)	/* dss_data2.dss_data2 */
+			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0)	/* dss_data3.dss_data3 */
+			OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0)	/* dss_data4.dss_data4 */
+			OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0)	/* dss_data5.dss_data5 */
+			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0)	/* dss_data6.dss_data6 */
+			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0)	/* dss_data7.dss_data7 */
+			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0)	/* dss_data8.dss_data8 */
+			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0)	/* dss_data9.dss_data9 */
+			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0)	/* dss_data10.dss_data10 */
+			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0)	/* dss_data11.dss_data11 */
+			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0)	/* dss_data12.dss_data12 */
+			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0)	/* dss_data13.dss_data13 */
+			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0)	/* dss_data14.dss_data14 */
+			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0)	/* dss_data15.dss_data15 */
+			OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0)	/* dss_data16.dss_data16 */
+			OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0)	/* dss_data17.dss_data17 */
+			OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0)	/* dss_data18.dss_data18 */
+			OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0)	/* dss_data19.dss_data19 */
+			OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0)	/* dss_data20.dss_data20 */
+			OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0)	/* dss_data21.dss_data21 */
+			OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0)	/* dss_data22.dss_data22 */
+			OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0)	/* dss_data23.dss_data23 */
+		>;
+	};
+};
+
+/* Needed to power the DPI pins */
+&vpll2 {
+	regulator-always-on;
+};
+
+&dss {
+	status = "ok";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_dpi_pins>;
+
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&tfp410_in>;
+			data-lines = <24>;
+		};
+	};
+};
+
+/ {
+	aliases {
+		display0 = &dvi0;
+	};
+
+	tfp410: encoder@0 {
+		compatible = "ti,tfp410";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				tfp410_in: endpoint@0 {
+					remote-endpoint = <&dpi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				tfp410_out: endpoint@0 {
+					remote-endpoint = <&dvi_connector_in>;
+				};
+			};
+		};
+	};
+
+	dvi0: connector@0 {
+		compatible = "dvi-connector";
+		label = "dvi";
+
+		digital;
+		ddc-i2c-bus = <&i2c3>;
+
+		port {
+			dvi_connector_in: endpoint {
+				remote-endpoint = <&tfp410_out>;
+			};
+		};
+	};
+};
+
diff --git a/arch/arm/boot/dts/omap3-overo-summit-common.dtsi b/arch/arm/boot/dts/omap3-overo-summit-common.dtsi
index 999d1cd..0ac97ba 100644
--- a/arch/arm/boot/dts/omap3-overo-summit-common.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-summit-common.dtsi
@@ -11,6 +11,7 @@
  */
 
 #include "omap3-overo-common-peripherals.dtsi"
+#include "omap3-overo-common-dvi.dtsi"
 
 / {
 	leds {
diff --git a/arch/arm/boot/dts/omap3-overo-tobi-common.dtsi b/arch/arm/boot/dts/omap3-overo-tobi-common.dtsi
index 13df50b..9e24b6a 100644
--- a/arch/arm/boot/dts/omap3-overo-tobi-common.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-tobi-common.dtsi
@@ -11,6 +11,7 @@
  */
 
 #include "omap3-overo-common-peripherals.dtsi"
+#include "omap3-overo-common-dvi.dtsi"
 
 / {
 	leds {
-- 
1.8.3.2


^ permalink raw reply related	[flat|nested] 14+ messages in thread
* [PATCH v3 1/3] ARM: dts: overo: Add support for DVI output
@ 2014-05-20 13:58   ` Florian Vaussard
  0 siblings, 0 replies; 14+ messages in thread
From: Florian Vaussard @ 2014-05-20 13:58 UTC (permalink / raw)
  To: linux-arm-kernel

Summit and Tobi expansion boards have a HDMI connector with a TFP410
encoder. Add a common include file for this configuration, and then
use it for Summit and Tobi.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
---
 arch/arm/boot/dts/omap3-overo-common-dvi.dtsi    | 111 +++++++++++++++++++++++
 arch/arm/boot/dts/omap3-overo-summit-common.dtsi |   1 +
 arch/arm/boot/dts/omap3-overo-tobi-common.dtsi   |   1 +
 3 files changed, 113 insertions(+)
 create mode 100644 arch/arm/boot/dts/omap3-overo-common-dvi.dtsi

diff --git a/arch/arm/boot/dts/omap3-overo-common-dvi.dtsi b/arch/arm/boot/dts/omap3-overo-common-dvi.dtsi
new file mode 100644
index 0000000..802f704
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-overo-common-dvi.dtsi
@@ -0,0 +1,111 @@
+/*
+ * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * DVI output for some Gumstix Overo boards (Tobi and Summit)
+ */
+
+&omap3_pmx_core {
+	dss_dpi_pins: pinmux_dss_dpi_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)	/* dss_pclk.dss_pclk */
+			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)	/* dss_hsync.dss_hsync */
+			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0)	/* dss_vsync.dss_vsync */
+			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0)	/* dss_acbias.dss_acbias */
+			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0)	/* dss_data0.dss_data0 */
+			OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0)	/* dss_data1.dss_data1 */
+			OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0)	/* dss_data2.dss_data2 */
+			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0)	/* dss_data3.dss_data3 */
+			OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0)	/* dss_data4.dss_data4 */
+			OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0)	/* dss_data5.dss_data5 */
+			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0)	/* dss_data6.dss_data6 */
+			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0)	/* dss_data7.dss_data7 */
+			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0)	/* dss_data8.dss_data8 */
+			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0)	/* dss_data9.dss_data9 */
+			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0)	/* dss_data10.dss_data10 */
+			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0)	/* dss_data11.dss_data11 */
+			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0)	/* dss_data12.dss_data12 */
+			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0)	/* dss_data13.dss_data13 */
+			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0)	/* dss_data14.dss_data14 */
+			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0)	/* dss_data15.dss_data15 */
+			OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0)	/* dss_data16.dss_data16 */
+			OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0)	/* dss_data17.dss_data17 */
+			OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0)	/* dss_data18.dss_data18 */
+			OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0)	/* dss_data19.dss_data19 */
+			OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0)	/* dss_data20.dss_data20 */
+			OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0)	/* dss_data21.dss_data21 */
+			OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0)	/* dss_data22.dss_data22 */
+			OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0)	/* dss_data23.dss_data23 */
+		>;
+	};
+};
+
+/* Needed to power the DPI pins */
+&vpll2 {
+	regulator-always-on;
+};
+
+&dss {
+	status = "ok";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_dpi_pins>;
+
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&tfp410_in>;
+			data-lines = <24>;
+		};
+	};
+};
+
+/ {
+	aliases {
+		display0 = &dvi0;
+	};
+
+	tfp410: encoder at 0 {
+		compatible = "ti,tfp410";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port at 0 {
+				reg = <0>;
+
+				tfp410_in: endpoint at 0 {
+					remote-endpoint = <&dpi_out>;
+				};
+			};
+
+			port at 1 {
+				reg = <1>;
+
+				tfp410_out: endpoint at 0 {
+					remote-endpoint = <&dvi_connector_in>;
+				};
+			};
+		};
+	};
+
+	dvi0: connector at 0 {
+		compatible = "dvi-connector";
+		label = "dvi";
+
+		digital;
+		ddc-i2c-bus = <&i2c3>;
+
+		port {
+			dvi_connector_in: endpoint {
+				remote-endpoint = <&tfp410_out>;
+			};
+		};
+	};
+};
+
diff --git a/arch/arm/boot/dts/omap3-overo-summit-common.dtsi b/arch/arm/boot/dts/omap3-overo-summit-common.dtsi
index 999d1cd..0ac97ba 100644
--- a/arch/arm/boot/dts/omap3-overo-summit-common.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-summit-common.dtsi
@@ -11,6 +11,7 @@
  */
 
 #include "omap3-overo-common-peripherals.dtsi"
+#include "omap3-overo-common-dvi.dtsi"
 
 / {
 	leds {
diff --git a/arch/arm/boot/dts/omap3-overo-tobi-common.dtsi b/arch/arm/boot/dts/omap3-overo-tobi-common.dtsi
index 13df50b..9e24b6a 100644
--- a/arch/arm/boot/dts/omap3-overo-tobi-common.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-tobi-common.dtsi
@@ -11,6 +11,7 @@
  */
 
 #include "omap3-overo-common-peripherals.dtsi"
+#include "omap3-overo-common-dvi.dtsi"
 
 / {
 	leds {
-- 
1.8.3.2

^ permalink raw reply related	[flat|nested] 14+ messages in thread
* [PATCH v3 2/3] ARM: dts: overo: Add support for 4.3'' LCD output
  2014-05-20 13:58 ` Florian Vaussard
@ 2014-05-20 13:58   ` Florian Vaussard
  -1 siblings, 0 replies; 14+ messages in thread
From: Florian Vaussard @ 2014-05-20 13:58 UTC (permalink / raw)
  To: Tony Lindgren; +Cc: Tomi Valkeinen, linux-omap, linux-arm-kernel, devicetree

Chestnut43, Gallop43 and Palo43 expansion boards have a ZIF connector
for a 4.3'' LCD. Add a common include file for this configuration, and
use it on relevant expansion boards.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
---
 .../boot/dts/omap3-overo-chestnut43-common.dtsi    |   1 +
 arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi    | 178 +++++++++++++++++++++
 arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi |   1 +
 arch/arm/boot/dts/omap3-overo-palo43-common.dtsi   |   1 +
 4 files changed, 181 insertions(+)
 create mode 100644 arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi

diff --git a/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi b/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi
index 19de6ff..17b82f8 100644
--- a/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi
@@ -11,6 +11,7 @@
  */
 
 #include "omap3-overo-common-peripherals.dtsi"
+#include "omap3-overo-common-lcd43.dtsi"
 
 #include <dt-bindings/input/input.h>
 
diff --git a/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi b/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi
new file mode 100644
index 0000000..f5395b7
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi
@@ -0,0 +1,178 @@
+/*
+ * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * 4.3'' LCD panel output for some Gumstix Overo boards (Gallop43, Chestnut43)
+ */
+
+&omap3_pmx_core {
+	dss_dpi_pins: pinmux_dss_dpi_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)	/* dss_pclk.dss_pclk */
+			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)	/* dss_hsync.dss_hsync */
+			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0)	/* dss_vsync.dss_vsync */
+			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0)	/* dss_acbias.dss_acbias */
+			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0)	/* dss_data0.dss_data0 */
+			OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0)	/* dss_data1.dss_data1 */
+			OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0)	/* dss_data2.dss_data2 */
+			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0)	/* dss_data3.dss_data3 */
+			OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0)	/* dss_data4.dss_data4 */
+			OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0)	/* dss_data5.dss_data5 */
+			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0)	/* dss_data6.dss_data6 */
+			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0)	/* dss_data7.dss_data7 */
+			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0)	/* dss_data8.dss_data8 */
+			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0)	/* dss_data9.dss_data9 */
+			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0)	/* dss_data10.dss_data10 */
+			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0)	/* dss_data11.dss_data11 */
+			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0)	/* dss_data12.dss_data12 */
+			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0)	/* dss_data13.dss_data13 */
+			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0)	/* dss_data14.dss_data14 */
+			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0)	/* dss_data15.dss_data15 */
+			OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0)	/* dss_data16.dss_data16 */
+			OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0)	/* dss_data17.dss_data17 */
+			OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0)	/* dss_data18.dss_data18 */
+			OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0)	/* dss_data19.dss_data19 */
+			OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0)	/* dss_data20.dss_data20 */
+			OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0)	/* dss_data21.dss_data21 */
+			OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0)	/* dss_data22.dss_data22 */
+			OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0)	/* dss_data23.dss_data23 */
+		>;
+	};
+
+	lte430_pins: pinmux_lte430_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2174, PIN_OUTPUT | MUX_MODE4)	/* uart2_cts.gpio_144 */
+		>;
+	};
+
+	backlight_pins: pinmux_backlight_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE4)	/* uart2_rts.gpio_145 */
+		>;
+	};
+
+	mcspi1_pins: pinmux_mcspi1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)	/* mcspi1_clk.mcspi1_clk */
+			OMAP3_CORE1_IOPAD(0x21ca, PIN_INPUT | MUX_MODE0)	/* mcspi1_simo.mcspi1_simo */
+			OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT | MUX_MODE0)	/* mcspi1_somi.mcspi1_somi */
+			OMAP3_CORE1_IOPAD(0x21ce, PIN_INPUT | MUX_MODE0)	/* mcspi1_cs0.mcspi1_cs0 */
+		>;
+	};
+
+	ads7846_pins: pinmux_ads7846_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2138, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* csi2_dx1.gpio_114 */
+		>;
+	};
+};
+
+/* Needed to power the DPI pins */
+&vpll2 {
+	regulator-always-on;
+};
+
+&dss {
+	status = "ok";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_dpi_pins>;
+
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&lcd_in>;
+			data-lines = <24>;
+		};
+	};
+};
+
+/ {
+	aliases {
+		display0 = &lcd0;
+	};
+
+	lcd0: display@0 {
+		compatible = "samsung,lte430wq-f0c", "panel-dpi";
+		label = "lcd";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lte430_pins>;
+		enable-gpios = <&gpio5 16 GPIO_ACTIVE_HIGH>;		/* gpio_144 */
+
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&dpi_out>;
+			};
+		};
+
+		panel-timing {
+			clock-frequency = <9200000>;
+			hactive = <480>;
+			vactive = <272>;
+			hfront-porch = <8>;
+			hback-porch = <4>;
+			hsync-len = <41>;
+			vback-porch = <2>;
+			vfront-porch = <4>;
+			vsync-len = <10>;
+
+			hsync-active = <0>;
+			vsync-active = <0>;
+			de-active = <1>;
+			pixelclk-active = <1>;
+		};
+	};
+
+	ads7846reg: ads7846-reg {
+		compatible = "regulator-fixed";
+		regulator-name = "ads7846-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	backlight {
+		compatible = "gpio-backlight";
+		
+		pinctrl-names = "default";
+		pinctrl-0 = <&backlight_pins>;
+		gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;		/* gpio_145 */
+
+		default-on;
+	};
+};
+
+&mcspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi1_pins>;
+
+	/* touch controller */
+	ads7846@0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&ads7846_pins>;
+
+		compatible = "ti,ads7846";
+		vcc-supply = <&ads7846reg>;
+
+		reg = <0>;				/* CS0 */
+		spi-max-frequency = <1500000>;
+
+		interrupt-parent = <&gpio4>;
+		interrupts = <18 0>;			/* gpio_114 */
+		pendown-gpio = <&gpio4 18 0>;
+
+		ti,x-min = /bits/ 16 <0x0>;
+		ti,x-max = /bits/ 16 <0x0fff>;
+		ti,y-min = /bits/ 16 <0x0>;
+		ti,y-max = /bits/ 16 <0x0fff>;
+		ti,x-plate-ohms = /bits/ 16 <180>;
+		ti,pressure-max = /bits/ 16 <255>;
+
+		linux,wakeup;
+	};
+};
+
diff --git a/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi b/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi
index 5e848c2..49d2254 100644
--- a/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi
@@ -11,6 +11,7 @@
  */
 
 #include "omap3-overo-common-peripherals.dtsi"
+#include "omap3-overo-common-lcd43.dtsi"
 
 #include <dt-bindings/input/input.h>
 
diff --git a/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi b/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi
index abea232..087aedf 100644
--- a/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi
@@ -11,6 +11,7 @@
  */
 
 #include "omap3-overo-common-peripherals.dtsi"
+#include "omap3-overo-common-lcd43.dtsi"
 
 #include <dt-bindings/input/input.h>
 
-- 
1.8.3.2


^ permalink raw reply related	[flat|nested] 14+ messages in thread
* [PATCH v3 2/3] ARM: dts: overo: Add support for 4.3'' LCD output
@ 2014-05-20 13:58   ` Florian Vaussard
  0 siblings, 0 replies; 14+ messages in thread
From: Florian Vaussard @ 2014-05-20 13:58 UTC (permalink / raw)
  To: linux-arm-kernel

Chestnut43, Gallop43 and Palo43 expansion boards have a ZIF connector
for a 4.3'' LCD. Add a common include file for this configuration, and
use it on relevant expansion boards.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
---
 .../boot/dts/omap3-overo-chestnut43-common.dtsi    |   1 +
 arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi    | 178 +++++++++++++++++++++
 arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi |   1 +
 arch/arm/boot/dts/omap3-overo-palo43-common.dtsi   |   1 +
 4 files changed, 181 insertions(+)
 create mode 100644 arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi

diff --git a/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi b/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi
index 19de6ff..17b82f8 100644
--- a/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi
@@ -11,6 +11,7 @@
  */
 
 #include "omap3-overo-common-peripherals.dtsi"
+#include "omap3-overo-common-lcd43.dtsi"
 
 #include <dt-bindings/input/input.h>
 
diff --git a/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi b/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi
new file mode 100644
index 0000000..f5395b7
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi
@@ -0,0 +1,178 @@
+/*
+ * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * 4.3'' LCD panel output for some Gumstix Overo boards (Gallop43, Chestnut43)
+ */
+
+&omap3_pmx_core {
+	dss_dpi_pins: pinmux_dss_dpi_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)	/* dss_pclk.dss_pclk */
+			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)	/* dss_hsync.dss_hsync */
+			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0)	/* dss_vsync.dss_vsync */
+			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0)	/* dss_acbias.dss_acbias */
+			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0)	/* dss_data0.dss_data0 */
+			OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0)	/* dss_data1.dss_data1 */
+			OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0)	/* dss_data2.dss_data2 */
+			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0)	/* dss_data3.dss_data3 */
+			OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0)	/* dss_data4.dss_data4 */
+			OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0)	/* dss_data5.dss_data5 */
+			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0)	/* dss_data6.dss_data6 */
+			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0)	/* dss_data7.dss_data7 */
+			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0)	/* dss_data8.dss_data8 */
+			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0)	/* dss_data9.dss_data9 */
+			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0)	/* dss_data10.dss_data10 */
+			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0)	/* dss_data11.dss_data11 */
+			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0)	/* dss_data12.dss_data12 */
+			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0)	/* dss_data13.dss_data13 */
+			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0)	/* dss_data14.dss_data14 */
+			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0)	/* dss_data15.dss_data15 */
+			OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0)	/* dss_data16.dss_data16 */
+			OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0)	/* dss_data17.dss_data17 */
+			OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0)	/* dss_data18.dss_data18 */
+			OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0)	/* dss_data19.dss_data19 */
+			OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0)	/* dss_data20.dss_data20 */
+			OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0)	/* dss_data21.dss_data21 */
+			OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0)	/* dss_data22.dss_data22 */
+			OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0)	/* dss_data23.dss_data23 */
+		>;
+	};
+
+	lte430_pins: pinmux_lte430_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2174, PIN_OUTPUT | MUX_MODE4)	/* uart2_cts.gpio_144 */
+		>;
+	};
+
+	backlight_pins: pinmux_backlight_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE4)	/* uart2_rts.gpio_145 */
+		>;
+	};
+
+	mcspi1_pins: pinmux_mcspi1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)	/* mcspi1_clk.mcspi1_clk */
+			OMAP3_CORE1_IOPAD(0x21ca, PIN_INPUT | MUX_MODE0)	/* mcspi1_simo.mcspi1_simo */
+			OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT | MUX_MODE0)	/* mcspi1_somi.mcspi1_somi */
+			OMAP3_CORE1_IOPAD(0x21ce, PIN_INPUT | MUX_MODE0)	/* mcspi1_cs0.mcspi1_cs0 */
+		>;
+	};
+
+	ads7846_pins: pinmux_ads7846_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2138, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* csi2_dx1.gpio_114 */
+		>;
+	};
+};
+
+/* Needed to power the DPI pins */
+&vpll2 {
+	regulator-always-on;
+};
+
+&dss {
+	status = "ok";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_dpi_pins>;
+
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&lcd_in>;
+			data-lines = <24>;
+		};
+	};
+};
+
+/ {
+	aliases {
+		display0 = &lcd0;
+	};
+
+	lcd0: display at 0 {
+		compatible = "samsung,lte430wq-f0c", "panel-dpi";
+		label = "lcd";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lte430_pins>;
+		enable-gpios = <&gpio5 16 GPIO_ACTIVE_HIGH>;		/* gpio_144 */
+
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&dpi_out>;
+			};
+		};
+
+		panel-timing {
+			clock-frequency = <9200000>;
+			hactive = <480>;
+			vactive = <272>;
+			hfront-porch = <8>;
+			hback-porch = <4>;
+			hsync-len = <41>;
+			vback-porch = <2>;
+			vfront-porch = <4>;
+			vsync-len = <10>;
+
+			hsync-active = <0>;
+			vsync-active = <0>;
+			de-active = <1>;
+			pixelclk-active = <1>;
+		};
+	};
+
+	ads7846reg: ads7846-reg {
+		compatible = "regulator-fixed";
+		regulator-name = "ads7846-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	backlight {
+		compatible = "gpio-backlight";
+		
+		pinctrl-names = "default";
+		pinctrl-0 = <&backlight_pins>;
+		gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;		/* gpio_145 */
+
+		default-on;
+	};
+};
+
+&mcspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi1_pins>;
+
+	/* touch controller */
+	ads7846 at 0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&ads7846_pins>;
+
+		compatible = "ti,ads7846";
+		vcc-supply = <&ads7846reg>;
+
+		reg = <0>;				/* CS0 */
+		spi-max-frequency = <1500000>;
+
+		interrupt-parent = <&gpio4>;
+		interrupts = <18 0>;			/* gpio_114 */
+		pendown-gpio = <&gpio4 18 0>;
+
+		ti,x-min = /bits/ 16 <0x0>;
+		ti,x-max = /bits/ 16 <0x0fff>;
+		ti,y-min = /bits/ 16 <0x0>;
+		ti,y-max = /bits/ 16 <0x0fff>;
+		ti,x-plate-ohms = /bits/ 16 <180>;
+		ti,pressure-max = /bits/ 16 <255>;
+
+		linux,wakeup;
+	};
+};
+
diff --git a/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi b/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi
index 5e848c2..49d2254 100644
--- a/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi
@@ -11,6 +11,7 @@
  */
 
 #include "omap3-overo-common-peripherals.dtsi"
+#include "omap3-overo-common-lcd43.dtsi"
 
 #include <dt-bindings/input/input.h>
 
diff --git a/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi b/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi
index abea232..087aedf 100644
--- a/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi
@@ -11,6 +11,7 @@
  */
 
 #include "omap3-overo-common-peripherals.dtsi"
+#include "omap3-overo-common-lcd43.dtsi"
 
 #include <dt-bindings/input/input.h>
 
-- 
1.8.3.2

^ permalink raw reply related	[flat|nested] 14+ messages in thread
* [PATCH v3 3/3] ARM: dts: overo: Add support for 3.5'' LCD output
  2014-05-20 13:58 ` Florian Vaussard
@ 2014-05-20 13:58   ` Florian Vaussard
  -1 siblings, 0 replies; 14+ messages in thread
From: Florian Vaussard @ 2014-05-20 13:58 UTC (permalink / raw)
  To: Tony Lindgren; +Cc: Tomi Valkeinen, linux-omap, linux-arm-kernel, devicetree

Alto35 expansion board has a ZIF connector for a 3.5'' LCD.
Add a common include file for this configuration, and use it
on Alto35.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
---
 arch/arm/boot/dts/omap3-overo-alto35-common.dtsi |   1 +
 arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi  | 165 +++++++++++++++++++++++
 2 files changed, 166 insertions(+)
 create mode 100644 arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi

diff --git a/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi b/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi
index 19d6486..7aae8fb 100644
--- a/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi
@@ -11,6 +11,7 @@
  */
 
 #include "omap3-overo-common-peripherals.dtsi"
+#include "omap3-overo-common-lcd35.dtsi"
 
 #include <dt-bindings/input/input.h>
 
diff --git a/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi b/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi
new file mode 100644
index 0000000..233c69e
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi
@@ -0,0 +1,165 @@
+/*
+ * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * 4.3'' LCD panel output for some Gumstix Overo boards (Gallop43, Chestnut43)
+ */
+
+&omap3_pmx_core {
+	dss_dpi_pins: pinmux_dss_dpi_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)	/* dss_pclk.dss_pclk */
+			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)	/* dss_hsync.dss_hsync */
+			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0)	/* dss_vsync.dss_vsync */
+			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0)	/* dss_acbias.dss_acbias */
+			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0)	/* dss_data0.dss_data0 */
+			OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0)	/* dss_data1.dss_data1 */
+			OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0)	/* dss_data2.dss_data2 */
+			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0)	/* dss_data3.dss_data3 */
+			OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0)	/* dss_data4.dss_data4 */
+			OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0)	/* dss_data5.dss_data5 */
+			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0)	/* dss_data6.dss_data6 */
+			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0)	/* dss_data7.dss_data7 */
+			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0)	/* dss_data8.dss_data8 */
+			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0)	/* dss_data9.dss_data9 */
+			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0)	/* dss_data10.dss_data10 */
+			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0)	/* dss_data11.dss_data11 */
+			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0)	/* dss_data12.dss_data12 */
+			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0)	/* dss_data13.dss_data13 */
+			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0)	/* dss_data14.dss_data14 */
+			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0)	/* dss_data15.dss_data15 */
+			OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0)	/* dss_data16.dss_data16 */
+			OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0)	/* dss_data17.dss_data17 */
+			OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0)	/* dss_data18.dss_data18 */
+			OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0)	/* dss_data19.dss_data19 */
+			OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0)	/* dss_data20.dss_data20 */
+			OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0)	/* dss_data21.dss_data21 */
+			OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0)	/* dss_data22.dss_data22 */
+			OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0)	/* dss_data23.dss_data23 */
+		>;
+	};
+
+	lb035_pins: pinmux_lb035_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2174, PIN_OUTPUT | MUX_MODE4)	/* uart2_cts.gpio_144 */
+		>;
+	};
+
+	backlight_pins: pinmux_backlight_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE4)	/* uart2_rts.gpio_145 */
+		>;
+	};
+
+	mcspi1_pins: pinmux_mcspi1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)	/* mcspi1_clk.mcspi1_clk */
+			OMAP3_CORE1_IOPAD(0x21ca, PIN_INPUT | MUX_MODE0)	/* mcspi1_simo.mcspi1_simo */
+			OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT | MUX_MODE0)	/* mcspi1_somi.mcspi1_somi */
+			OMAP3_CORE1_IOPAD(0x21ce, PIN_INPUT | MUX_MODE0)	/* mcspi1_cs0.mcspi1_cs0 */
+		>;
+	};
+
+	ads7846_pins: pinmux_ads7846_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2138, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* csi2_dx1.gpio_114 */
+		>;
+	};
+};
+
+/* Needed to power the DPI pins */
+&vpll2 {
+	regulator-always-on;
+};
+
+&dss {
+	status = "ok";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_dpi_pins>;
+
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&lcd_in>;
+			data-lines = <24>;
+		};
+	};
+};
+
+/ {
+	aliases {
+		display0 = &lcd0;
+	};
+
+	ads7846reg: ads7846-reg {
+		compatible = "regulator-fixed";
+		regulator-name = "ads7846-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	backlight {
+		compatible = "gpio-backlight";
+		
+		pinctrl-names = "default";
+		pinctrl-0 = <&backlight_pins>;
+		gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;		/* gpio_145 */
+
+		default-on;
+	};
+};
+
+&mcspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi1_pins>;
+
+	lcd0: display@0 {
+		compatible = "lgphilips,lb035q02";
+		label = "lcd";
+
+		reg = <1>;					/* CS1 */
+		spi-max-frequency = <10000000>;
+		spi-cpol;
+		spi-cpha;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lb035_pins>;
+		enable-gpios = <&gpio5 16 GPIO_ACTIVE_HIGH>;	/* gpio_144 */
+
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&dpi_out>;
+			};
+		};
+	};
+
+	/* touch controller */
+	ads7846@0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&ads7846_pins>;
+
+		compatible = "ti,ads7846";
+		vcc-supply = <&ads7846reg>;
+
+		reg = <0>;				/* CS0 */
+		spi-max-frequency = <1500000>;
+
+		interrupt-parent = <&gpio4>;
+		interrupts = <18 0>;			/* gpio_114 */
+		pendown-gpio = <&gpio4 18 0>;
+
+		ti,x-min = /bits/ 16 <0x0>;
+		ti,x-max = /bits/ 16 <0x0fff>;
+		ti,y-min = /bits/ 16 <0x0>;
+		ti,y-max = /bits/ 16 <0x0fff>;
+		ti,x-plate-ohms = /bits/ 16 <180>;
+		ti,pressure-max = /bits/ 16 <255>;
+
+		linux,wakeup;
+	};
+};
-- 
1.8.3.2


^ permalink raw reply related	[flat|nested] 14+ messages in thread
* [PATCH v3 3/3] ARM: dts: overo: Add support for 3.5'' LCD output
@ 2014-05-20 13:58   ` Florian Vaussard
  0 siblings, 0 replies; 14+ messages in thread
From: Florian Vaussard @ 2014-05-20 13:58 UTC (permalink / raw)
  To: linux-arm-kernel

Alto35 expansion board has a ZIF connector for a 3.5'' LCD.
Add a common include file for this configuration, and use it
on Alto35.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
---
 arch/arm/boot/dts/omap3-overo-alto35-common.dtsi |   1 +
 arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi  | 165 +++++++++++++++++++++++
 2 files changed, 166 insertions(+)
 create mode 100644 arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi

diff --git a/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi b/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi
index 19d6486..7aae8fb 100644
--- a/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi
@@ -11,6 +11,7 @@
  */
 
 #include "omap3-overo-common-peripherals.dtsi"
+#include "omap3-overo-common-lcd35.dtsi"
 
 #include <dt-bindings/input/input.h>
 
diff --git a/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi b/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi
new file mode 100644
index 0000000..233c69e
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi
@@ -0,0 +1,165 @@
+/*
+ * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * 4.3'' LCD panel output for some Gumstix Overo boards (Gallop43, Chestnut43)
+ */
+
+&omap3_pmx_core {
+	dss_dpi_pins: pinmux_dss_dpi_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)	/* dss_pclk.dss_pclk */
+			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)	/* dss_hsync.dss_hsync */
+			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0)	/* dss_vsync.dss_vsync */
+			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0)	/* dss_acbias.dss_acbias */
+			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0)	/* dss_data0.dss_data0 */
+			OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0)	/* dss_data1.dss_data1 */
+			OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0)	/* dss_data2.dss_data2 */
+			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0)	/* dss_data3.dss_data3 */
+			OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0)	/* dss_data4.dss_data4 */
+			OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0)	/* dss_data5.dss_data5 */
+			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0)	/* dss_data6.dss_data6 */
+			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0)	/* dss_data7.dss_data7 */
+			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0)	/* dss_data8.dss_data8 */
+			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0)	/* dss_data9.dss_data9 */
+			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0)	/* dss_data10.dss_data10 */
+			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0)	/* dss_data11.dss_data11 */
+			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0)	/* dss_data12.dss_data12 */
+			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0)	/* dss_data13.dss_data13 */
+			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0)	/* dss_data14.dss_data14 */
+			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0)	/* dss_data15.dss_data15 */
+			OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0)	/* dss_data16.dss_data16 */
+			OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0)	/* dss_data17.dss_data17 */
+			OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0)	/* dss_data18.dss_data18 */
+			OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0)	/* dss_data19.dss_data19 */
+			OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0)	/* dss_data20.dss_data20 */
+			OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0)	/* dss_data21.dss_data21 */
+			OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0)	/* dss_data22.dss_data22 */
+			OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0)	/* dss_data23.dss_data23 */
+		>;
+	};
+
+	lb035_pins: pinmux_lb035_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2174, PIN_OUTPUT | MUX_MODE4)	/* uart2_cts.gpio_144 */
+		>;
+	};
+
+	backlight_pins: pinmux_backlight_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE4)	/* uart2_rts.gpio_145 */
+		>;
+	};
+
+	mcspi1_pins: pinmux_mcspi1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)	/* mcspi1_clk.mcspi1_clk */
+			OMAP3_CORE1_IOPAD(0x21ca, PIN_INPUT | MUX_MODE0)	/* mcspi1_simo.mcspi1_simo */
+			OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT | MUX_MODE0)	/* mcspi1_somi.mcspi1_somi */
+			OMAP3_CORE1_IOPAD(0x21ce, PIN_INPUT | MUX_MODE0)	/* mcspi1_cs0.mcspi1_cs0 */
+		>;
+	};
+
+	ads7846_pins: pinmux_ads7846_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2138, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* csi2_dx1.gpio_114 */
+		>;
+	};
+};
+
+/* Needed to power the DPI pins */
+&vpll2 {
+	regulator-always-on;
+};
+
+&dss {
+	status = "ok";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_dpi_pins>;
+
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&lcd_in>;
+			data-lines = <24>;
+		};
+	};
+};
+
+/ {
+	aliases {
+		display0 = &lcd0;
+	};
+
+	ads7846reg: ads7846-reg {
+		compatible = "regulator-fixed";
+		regulator-name = "ads7846-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	backlight {
+		compatible = "gpio-backlight";
+		
+		pinctrl-names = "default";
+		pinctrl-0 = <&backlight_pins>;
+		gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;		/* gpio_145 */
+
+		default-on;
+	};
+};
+
+&mcspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi1_pins>;
+
+	lcd0: display at 0 {
+		compatible = "lgphilips,lb035q02";
+		label = "lcd";
+
+		reg = <1>;					/* CS1 */
+		spi-max-frequency = <10000000>;
+		spi-cpol;
+		spi-cpha;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lb035_pins>;
+		enable-gpios = <&gpio5 16 GPIO_ACTIVE_HIGH>;	/* gpio_144 */
+
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&dpi_out>;
+			};
+		};
+	};
+
+	/* touch controller */
+	ads7846 at 0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&ads7846_pins>;
+
+		compatible = "ti,ads7846";
+		vcc-supply = <&ads7846reg>;
+
+		reg = <0>;				/* CS0 */
+		spi-max-frequency = <1500000>;
+
+		interrupt-parent = <&gpio4>;
+		interrupts = <18 0>;			/* gpio_114 */
+		pendown-gpio = <&gpio4 18 0>;
+
+		ti,x-min = /bits/ 16 <0x0>;
+		ti,x-max = /bits/ 16 <0x0fff>;
+		ti,y-min = /bits/ 16 <0x0>;
+		ti,y-max = /bits/ 16 <0x0fff>;
+		ti,x-plate-ohms = /bits/ 16 <180>;
+		ti,pressure-max = /bits/ 16 <255>;
+
+		linux,wakeup;
+	};
+};
-- 
1.8.3.2

^ permalink raw reply related	[flat|nested] 14+ messages in thread
* Re: [PATCH v3 0/3] ARM: dts: overo: Add panel support
  2014-05-20 13:58 ` Florian Vaussard
@ 2014-05-23  7:09   ` Florian Vaussard
  -1 siblings, 0 replies; 14+ messages in thread
From: Florian Vaussard @ 2014-05-23  7:09 UTC (permalink / raw)
  To: Tomi Valkeinen; +Cc: Tony Lindgren, linux-omap, linux-arm-kernel, devicetree

Hi Tomi,

On 05/20/2014 03:58 PM, Florian Vaussard wrote:
> Hi,
> 
> This series enables the DVI and LCD panels present on some of
> the Overo expansion boards.
> 

Do you have any more comments on these? If no, do you want to pull them
through your tree for 3.16, as discussed with Tony?

Regards,

Florian

> DVI output:
> - Tobi
> - Summit
> 
> LCD (3.5''):
> - Alto35
> 
> LCD (4.3''):
> - Chestnut43
> - Palo43
> - Gallop43
> 
> I tested on Tobi, Alto35 and Gallop43.
> 
> This series depends on several patches from Tomi [1][2][3] targeting 3.16.
> 
> Regards,
> Florian
> 
> Since v2:
> - Use gpio-backlight
> Since v1:
> - Rebased on 3.15-rc4 + recent patches from Tomi
> 
> [1] http://thread.gmane.org/gmane.linux.ports.arm.omap/114572
> [2] http://thread.gmane.org/gmane.linux.ports.arm.omap/114560
> [3] http://lists.infradead.org/pipermail/linux-arm-kernel/2014-January/227101.html
> 
> Florian Vaussard (3):
>   ARM: dts: overo: Add support for DVI output
>   ARM: dts: overo: Add support for 4.3'' LCD output
>   ARM: dts: overo: Add support for 3.5'' LCD output
> 
>  arch/arm/boot/dts/omap3-overo-alto35-common.dtsi   |   1 +
>  .../boot/dts/omap3-overo-chestnut43-common.dtsi    |   1 +
>  arch/arm/boot/dts/omap3-overo-common-dvi.dtsi      | 111 +++++++++++++
>  arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi    | 165 +++++++++++++++++++
>  arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi    | 178 +++++++++++++++++++++
>  arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi |   1 +
>  arch/arm/boot/dts/omap3-overo-palo43-common.dtsi   |   1 +
>  arch/arm/boot/dts/omap3-overo-summit-common.dtsi   |   1 +
>  arch/arm/boot/dts/omap3-overo-tobi-common.dtsi     |   1 +
>  9 files changed, 460 insertions(+)
>  create mode 100644 arch/arm/boot/dts/omap3-overo-common-dvi.dtsi
>  create mode 100644 arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi
>  create mode 100644 arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi
> 

^ permalink raw reply	[flat|nested] 14+ messages in thread
* [PATCH v3 0/3] ARM: dts: overo: Add panel support
@ 2014-05-23  7:09   ` Florian Vaussard
  0 siblings, 0 replies; 14+ messages in thread
From: Florian Vaussard @ 2014-05-23  7:09 UTC (permalink / raw)
  To: linux-arm-kernel

Hi Tomi,

On 05/20/2014 03:58 PM, Florian Vaussard wrote:
> Hi,
> 
> This series enables the DVI and LCD panels present on some of
> the Overo expansion boards.
> 

Do you have any more comments on these? If no, do you want to pull them
through your tree for 3.16, as discussed with Tony?

Regards,

Florian

> DVI output:
> - Tobi
> - Summit
> 
> LCD (3.5''):
> - Alto35
> 
> LCD (4.3''):
> - Chestnut43
> - Palo43
> - Gallop43
> 
> I tested on Tobi, Alto35 and Gallop43.
> 
> This series depends on several patches from Tomi [1][2][3] targeting 3.16.
> 
> Regards,
> Florian
> 
> Since v2:
> - Use gpio-backlight
> Since v1:
> - Rebased on 3.15-rc4 + recent patches from Tomi
> 
> [1] http://thread.gmane.org/gmane.linux.ports.arm.omap/114572
> [2] http://thread.gmane.org/gmane.linux.ports.arm.omap/114560
> [3] http://lists.infradead.org/pipermail/linux-arm-kernel/2014-January/227101.html
> 
> Florian Vaussard (3):
>   ARM: dts: overo: Add support for DVI output
>   ARM: dts: overo: Add support for 4.3'' LCD output
>   ARM: dts: overo: Add support for 3.5'' LCD output
> 
>  arch/arm/boot/dts/omap3-overo-alto35-common.dtsi   |   1 +
>  .../boot/dts/omap3-overo-chestnut43-common.dtsi    |   1 +
>  arch/arm/boot/dts/omap3-overo-common-dvi.dtsi      | 111 +++++++++++++
>  arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi    | 165 +++++++++++++++++++
>  arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi    | 178 +++++++++++++++++++++
>  arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi |   1 +
>  arch/arm/boot/dts/omap3-overo-palo43-common.dtsi   |   1 +
>  arch/arm/boot/dts/omap3-overo-summit-common.dtsi   |   1 +
>  arch/arm/boot/dts/omap3-overo-tobi-common.dtsi     |   1 +
>  9 files changed, 460 insertions(+)
>  create mode 100644 arch/arm/boot/dts/omap3-overo-common-dvi.dtsi
>  create mode 100644 arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi
>  create mode 100644 arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi
> 

^ permalink raw reply	[flat|nested] 14+ messages in thread
* Re: [PATCH v3 0/3] ARM: dts: overo: Add panel support
  2014-05-23  7:09   ` Florian Vaussard
@ 2014-05-23  8:18     ` Tomi Valkeinen
  -1 siblings, 0 replies; 14+ messages in thread
From: Tomi Valkeinen @ 2014-05-23  8:18 UTC (permalink / raw)
  To: Florian Vaussard, Tony Lindgren; +Cc: linux-omap, linux-arm-kernel, devicetree

[-- Attachment #1: Type: text/plain, Size: 442 bytes --]

On 23/05/14 10:09, Florian Vaussard wrote:
> Hi Tomi,
> 
> On 05/20/2014 03:58 PM, Florian Vaussard wrote:
>> Hi,
>>
>> This series enables the DVI and LCD panels present on some of
>> the Overo expansion boards.
>>
> 
> Do you have any more comments on these? If no, do you want to pull them
> through your tree for 3.16, as discussed with Tony?

Yes, I can take these.

Tony, do I have your ack on this series?

 Tomi



[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

^ permalink raw reply	[flat|nested] 14+ messages in thread
* [PATCH v3 0/3] ARM: dts: overo: Add panel support
@ 2014-05-23  8:18     ` Tomi Valkeinen
  0 siblings, 0 replies; 14+ messages in thread
From: Tomi Valkeinen @ 2014-05-23  8:18 UTC (permalink / raw)
  To: linux-arm-kernel

On 23/05/14 10:09, Florian Vaussard wrote:
> Hi Tomi,
> 
> On 05/20/2014 03:58 PM, Florian Vaussard wrote:
>> Hi,
>>
>> This series enables the DVI and LCD panels present on some of
>> the Overo expansion boards.
>>
> 
> Do you have any more comments on these? If no, do you want to pull them
> through your tree for 3.16, as discussed with Tony?

Yes, I can take these.

Tony, do I have your ack on this series?

 Tomi


-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140523/d1517875/attachment-0001.sig>

^ permalink raw reply	[flat|nested] 14+ messages in thread
* Re: [PATCH v3 0/3] ARM: dts: overo: Add panel support
  2014-05-23  8:18     ` Tomi Valkeinen
@ 2014-05-23 14:28       ` Tony Lindgren
  -1 siblings, 0 replies; 14+ messages in thread
From: Tony Lindgren @ 2014-05-23 14:28 UTC (permalink / raw)
  To: Tomi Valkeinen; +Cc: Florian Vaussard, linux-omap, linux-arm-kernel, devicetree

* Tomi Valkeinen <tomi.valkeinen@ti.com> [140523 01:19]:
> On 23/05/14 10:09, Florian Vaussard wrote:
> > Hi Tomi,
> > 
> > On 05/20/2014 03:58 PM, Florian Vaussard wrote:
> >> Hi,
> >>
> >> This series enables the DVI and LCD panels present on some of
> >> the Overo expansion boards.
> >>
> > 
> > Do you have any more comments on these? If no, do you want to pull them
> > through your tree for 3.16, as discussed with Tony?
> 
> Yes, I can take these.
> 
> Tony, do I have your ack on this series?

Yes please go ahead and queue these:

Acked-by: Tony Lindgren <tony@atomide.com>

^ permalink raw reply	[flat|nested] 14+ messages in thread
* [PATCH v3 0/3] ARM: dts: overo: Add panel support
@ 2014-05-23 14:28       ` Tony Lindgren
  0 siblings, 0 replies; 14+ messages in thread
From: Tony Lindgren @ 2014-05-23 14:28 UTC (permalink / raw)
  To: linux-arm-kernel

* Tomi Valkeinen <tomi.valkeinen@ti.com> [140523 01:19]:
> On 23/05/14 10:09, Florian Vaussard wrote:
> > Hi Tomi,
> > 
> > On 05/20/2014 03:58 PM, Florian Vaussard wrote:
> >> Hi,
> >>
> >> This series enables the DVI and LCD panels present on some of
> >> the Overo expansion boards.
> >>
> > 
> > Do you have any more comments on these? If no, do you want to pull them
> > through your tree for 3.16, as discussed with Tony?
> 
> Yes, I can take these.
> 
> Tony, do I have your ack on this series?

Yes please go ahead and queue these:

Acked-by: Tony Lindgren <tony@atomide.com>

^ permalink raw reply	[flat|nested] 14+ messages in thread
end of thread, other threads:[~2014-05-23 14:28 UTC | newest]

Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-05-20 13:58 [PATCH v3 0/3] ARM: dts: overo: Add panel support Florian Vaussard
2014-05-20 13:58 ` Florian Vaussard
2014-05-20 13:58 ` [PATCH v3 1/3] ARM: dts: overo: Add support for DVI output Florian Vaussard
2014-05-20 13:58   ` Florian Vaussard
2014-05-20 13:58 ` [PATCH v3 2/3] ARM: dts: overo: Add support for 4.3'' LCD output Florian Vaussard
2014-05-20 13:58   ` Florian Vaussard
2014-05-20 13:58 ` [PATCH v3 3/3] ARM: dts: overo: Add support for 3.5'' " Florian Vaussard
2014-05-20 13:58   ` Florian Vaussard
2014-05-23  7:09 ` [PATCH v3 0/3] ARM: dts: overo: Add panel support Florian Vaussard
2014-05-23  7:09   ` Florian Vaussard
2014-05-23  8:18   ` Tomi Valkeinen
2014-05-23  8:18     ` Tomi Valkeinen
2014-05-23 14:28     ` Tony Lindgren
2014-05-23 14:28       ` Tony Lindgren

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.