From: Tero Kristo <t-kristo@ti.com>
To: Tony Lindgren <tony@atomide.com>, Paul Walmsley <paul@pwsan.com>
Cc: linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
kernel-build-reports@lists.linaro.org
Subject: Re: OMAP baseline test results for v3.16-rc4
Date: Thu, 31 Jul 2014 16:12:03 +0300 [thread overview]
Message-ID: <53DA40A3.30102@ti.com> (raw)
In-Reply-To: <20140730053940.GX29045@atomide.com>
On 07/30/2014 08:39 AM, Tony Lindgren wrote:
> 8< -----------------------------------
> From: Tony Lindgren<tony@atomide.com>
> Date: Tue, 29 Jul 2014 22:36:59 -0700
> Subject: [PATCH] ARM: dts: Enable UART wake-up events for beagleboard
>
> For device tree based booting, we need to use wake-up
> interrupts like we already do for some omaps. This fixes
> a PM regression on beagleboard compared to legacy booting.
>
> Signed-off-by: Tony Lindgren<tony@atomide.com>
>
> --- a/arch/arm/boot/dts/omap3-beagle.dts
> +++ b/arch/arm/boot/dts/omap3-beagle.dts
> @@ -292,6 +292,7 @@
> &uart3 {
> pinctrl-names = "default";
> pinctrl-0 = <&uart3_pins>;
> + interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
> };
>
> &gpio1 {
> --
The above patch works for me with ret/off-idle on beagle rev C4 on top
of 3.16-rc5. Without it, the board just seems to hang with ret, and with
off, it just doesn't respond to anything on uart but seems alive otherwise.
Tested-by: Tero Kristo <t-kristo@ti.com>
WARNING: multiple messages have this Message-ID (diff)
From: t-kristo@ti.com (Tero Kristo)
To: linux-arm-kernel@lists.infradead.org
Subject: OMAP baseline test results for v3.16-rc4
Date: Thu, 31 Jul 2014 16:12:03 +0300 [thread overview]
Message-ID: <53DA40A3.30102@ti.com> (raw)
In-Reply-To: <20140730053940.GX29045@atomide.com>
On 07/30/2014 08:39 AM, Tony Lindgren wrote:
> 8< -----------------------------------
> From: Tony Lindgren<tony@atomide.com>
> Date: Tue, 29 Jul 2014 22:36:59 -0700
> Subject: [PATCH] ARM: dts: Enable UART wake-up events for beagleboard
>
> For device tree based booting, we need to use wake-up
> interrupts like we already do for some omaps. This fixes
> a PM regression on beagleboard compared to legacy booting.
>
> Signed-off-by: Tony Lindgren<tony@atomide.com>
>
> --- a/arch/arm/boot/dts/omap3-beagle.dts
> +++ b/arch/arm/boot/dts/omap3-beagle.dts
> @@ -292,6 +292,7 @@
> &uart3 {
> pinctrl-names = "default";
> pinctrl-0 = <&uart3_pins>;
> + interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
> };
>
> &gpio1 {
> --
The above patch works for me with ret/off-idle on beagle rev C4 on top
of 3.16-rc5. Without it, the board just seems to hang with ret, and with
off, it just doesn't respond to anything on uart but seems alive otherwise.
Tested-by: Tero Kristo <t-kristo@ti.com>
next prev parent reply other threads:[~2014-07-31 13:10 UTC|newest]
Thread overview: 60+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-07-06 23:41 OMAP baseline test results for v3.16-rc4 Paul Walmsley
2014-07-06 23:41 ` Paul Walmsley
2014-07-07 8:02 ` Tony Lindgren
2014-07-07 8:02 ` Tony Lindgren
2014-07-14 17:28 ` Paul Walmsley
2014-07-14 17:28 ` Paul Walmsley
2014-07-15 6:04 ` Tony Lindgren
2014-07-15 6:04 ` Tony Lindgren
2014-07-15 19:56 ` Paul Walmsley
2014-07-15 19:56 ` Paul Walmsley
2014-07-25 19:14 ` Paul Walmsley
2014-07-25 19:14 ` Paul Walmsley
2014-07-29 6:42 ` Tony Lindgren
2014-07-29 6:42 ` Tony Lindgren
2014-07-29 8:25 ` Paul Walmsley
2014-07-29 8:25 ` Paul Walmsley
2014-07-29 8:49 ` Tony Lindgren
2014-07-29 8:49 ` Tony Lindgren
2014-07-29 12:32 ` Paul Walmsley
2014-07-29 12:32 ` Paul Walmsley
2014-07-29 12:57 ` Paul Walmsley
2014-07-29 12:57 ` Paul Walmsley
2014-07-29 14:53 ` Tony Lindgren
2014-07-29 14:53 ` Tony Lindgren
2014-07-29 19:37 ` Paul Walmsley
2014-07-29 19:37 ` Paul Walmsley
2014-07-30 5:39 ` Tony Lindgren
2014-07-30 5:39 ` Tony Lindgren
2014-07-30 7:53 ` Paul Walmsley
2014-07-30 7:53 ` Paul Walmsley
2014-07-31 13:11 ` Tony Lindgren
2014-07-31 13:11 ` Tony Lindgren
2014-07-31 19:27 ` Paul Walmsley
2014-07-31 19:27 ` Paul Walmsley
2014-08-01 7:10 ` Tony Lindgren
2014-08-01 7:10 ` Tony Lindgren
2014-08-01 7:52 ` Tony Lindgren
2014-08-01 7:52 ` Tony Lindgren
2014-08-07 22:21 ` Paul Walmsley
2014-08-07 22:21 ` Paul Walmsley
2014-08-08 2:14 ` Felipe Balbi
2014-08-08 2:14 ` Felipe Balbi
2014-08-08 6:11 ` Paul Walmsley
2014-08-08 6:11 ` Paul Walmsley
2014-08-08 14:34 ` Felipe Balbi
2014-08-08 14:34 ` Felipe Balbi
2014-08-08 23:39 ` Paul Walmsley
2014-08-08 23:39 ` Paul Walmsley
2014-08-09 2:49 ` Felipe Balbi
2014-08-09 2:49 ` Felipe Balbi
2014-08-08 2:29 ` Fabio Estevam
2014-08-08 2:29 ` Fabio Estevam
2014-08-08 6:14 ` Paul Walmsley
2014-08-08 6:14 ` Paul Walmsley
2014-08-09 12:41 ` Ezequiel Garcia
2014-08-09 12:41 ` Ezequiel Garcia
2014-07-31 13:12 ` Tero Kristo [this message]
2014-07-31 13:12 ` Tero Kristo
2014-07-29 8:50 ` Paul Walmsley
2014-07-29 8:50 ` Paul Walmsley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=53DA40A3.30102@ti.com \
--to=t-kristo@ti.com \
--cc=kernel-build-reports@lists.linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-omap@vger.kernel.org \
--cc=paul@pwsan.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.