[PATCH RESEND v6 0/7] net: cpsw: Support for am335x chip MACIDs

[PATCH RESEND v6 0/7] net: cpsw: Support for am335x chip MACIDs

[Markus Pargmann]

Hi,

Another resend of this series to add the netdev list.

This series adds support to the cpsw driver to read the MACIDs of the am335x
chip and use them as fallback. These addresses are only used if there are no
mac addresses in the devicetree, for example set by a bootloader.

Best regards,

Markus


Markus Pargmann (7):
  DT doc: net: cpsw mac-address is optional
  net: cpsw: Add missing return value
  net: cpsw: header, Add missing include
  net: cpsw: Replace pr_err by dev_err
  net: cpsw: Add am33xx MACID readout
  am33xx: define syscon control module device node
  arm: dts: am33xx, Add syscon phandle to cpsw node

 Documentation/devicetree/bindings/net/cpsw.txt |  6 +++-
 arch/arm/boot/dts/am33xx.dtsi                  |  6 ++++
 drivers/net/ethernet/ti/Kconfig                |  2 ++
 drivers/net/ethernet/ti/cpsw.c                 | 45 ++++++++++++++++++++++++--
 drivers/net/ethernet/ti/cpsw.h                 |  1 +
 5 files changed, 57 insertions(+), 3 deletions(-)

-- 
2.1.0

[PATCH RESEND v6 0/7] net: cpsw: Support for am335x chip MACIDs

[Markus Pargmann]

Hi,

Another resend of this series to add the netdev list.

This series adds support to the cpsw driver to read the MACIDs of the am335x
chip and use them as fallback. These addresses are only used if there are no
mac addresses in the devicetree, for example set by a bootloader.

Best regards,

Markus


Markus Pargmann (7):
  DT doc: net: cpsw mac-address is optional
  net: cpsw: Add missing return value
  net: cpsw: header, Add missing include
  net: cpsw: Replace pr_err by dev_err
  net: cpsw: Add am33xx MACID readout
  am33xx: define syscon control module device node
  arm: dts: am33xx, Add syscon phandle to cpsw node

 Documentation/devicetree/bindings/net/cpsw.txt |  6 +++-
 arch/arm/boot/dts/am33xx.dtsi                  |  6 ++++
 drivers/net/ethernet/ti/Kconfig                |  2 ++
 drivers/net/ethernet/ti/cpsw.c                 | 45 ++++++++++++++++++++++++--
 drivers/net/ethernet/ti/cpsw.h                 |  1 +
 5 files changed, 57 insertions(+), 3 deletions(-)

-- 
2.1.0

[PATCH RESEND v6 1/7] DT doc: net: cpsw mac-address is optional

[Markus Pargmann]

mac-address is an optional property. If no mac-address is set, a random
mac-address will be generated.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
---
 Documentation/devicetree/bindings/net/cpsw.txt | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt
index ae2b8b7f9c38..107caf174a0e 100644
--- a/Documentation/devicetree/bindings/net/cpsw.txt
+++ b/Documentation/devicetree/bindings/net/cpsw.txt
@@ -29,10 +29,10 @@ Slave Properties:
 Required properties:
 - phy_id		: Specifies slave phy id
 - phy-mode		: See ethernet.txt file in the same directory
-- mac-address		: See ethernet.txt file in the same directory
 
 Optional properties:
 - dual_emac_res_vlan	: Specifies VID to be used to segregate the ports
+- mac-address		: See ethernet.txt file in the same directory
 
 Note: "ti,hwmods" field is used to fetch the base address and irq
 resources from TI, omap hwmod data base during device registration.
-- 
2.1.0

[PATCH RESEND v6 1/7] DT doc: net: cpsw mac-address is optional

[Markus Pargmann]

mac-address is an optional property. If no mac-address is set, a random
mac-address will be generated.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
---
 Documentation/devicetree/bindings/net/cpsw.txt | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt
index ae2b8b7f9c38..107caf174a0e 100644
--- a/Documentation/devicetree/bindings/net/cpsw.txt
+++ b/Documentation/devicetree/bindings/net/cpsw.txt
@@ -29,10 +29,10 @@ Slave Properties:
 Required properties:
 - phy_id		: Specifies slave phy id
 - phy-mode		: See ethernet.txt file in the same directory
-- mac-address		: See ethernet.txt file in the same directory
 
 Optional properties:
 - dual_emac_res_vlan	: Specifies VID to be used to segregate the ports
+- mac-address		: See ethernet.txt file in the same directory
 
 Note: "ti,hwmods" field is used to fetch the base address and irq
 resources from TI, omap hwmod data base during device registration.
-- 
2.1.0

[PATCH RESEND v6 2/7] net: cpsw: Add missing return value

[Markus Pargmann]

ret is set 0 at this point, so jumping to that error label would result
in a return value of 0. Set ret to -ENOMEM to return a proper error
value.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
---
 drivers/net/ethernet/ti/cpsw.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c
index 999fb72688d2..f09b4639ad31 100644
--- a/drivers/net/ethernet/ti/cpsw.c
+++ b/drivers/net/ethernet/ti/cpsw.c
@@ -2063,6 +2063,7 @@ static int cpsw_probe(struct platform_device *pdev)
 	priv->irq_enabled = true;
 	if (!priv->cpts) {
 		dev_err(&pdev->dev, "error allocating cpts\n");
+		ret = -ENOMEM;
 		goto clean_ndev_ret;
 	}
 
-- 
2.1.0

[PATCH RESEND v6 2/7] net: cpsw: Add missing return value

[Markus Pargmann]

ret is set 0 at this point, so jumping to that error label would result
in a return value of 0. Set ret to -ENOMEM to return a proper error
value.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
---
 drivers/net/ethernet/ti/cpsw.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c
index 999fb72688d2..f09b4639ad31 100644
--- a/drivers/net/ethernet/ti/cpsw.c
+++ b/drivers/net/ethernet/ti/cpsw.c
@@ -2063,6 +2063,7 @@ static int cpsw_probe(struct platform_device *pdev)
 	priv->irq_enabled = true;
 	if (!priv->cpts) {
 		dev_err(&pdev->dev, "error allocating cpts\n");
+		ret = -ENOMEM;
 		goto clean_ndev_ret;
 	}
 
-- 
2.1.0

[PATCH RESEND v6 3/7] net: cpsw: header, Add missing include

[Markus Pargmann]

"MII_BUS_ID_SIZE" is defined in linux/phy.h which is not included in the
cpsw.h file.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
---
 drivers/net/ethernet/ti/cpsw.h | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/ethernet/ti/cpsw.h b/drivers/net/ethernet/ti/cpsw.h
index 574f49da693f..1b710674630c 100644
--- a/drivers/net/ethernet/ti/cpsw.h
+++ b/drivers/net/ethernet/ti/cpsw.h
@@ -15,6 +15,7 @@
 #define __CPSW_H__
 
 #include <linux/if_ether.h>
+#include <linux/phy.h>
 
 struct cpsw_slave_data {
 	char		phy_id[MII_BUS_ID_SIZE];
-- 
2.1.0

[PATCH RESEND v6 3/7] net: cpsw: header, Add missing include

[Markus Pargmann]

"MII_BUS_ID_SIZE" is defined in linux/phy.h which is not included in the
cpsw.h file.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
---
 drivers/net/ethernet/ti/cpsw.h | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/ethernet/ti/cpsw.h b/drivers/net/ethernet/ti/cpsw.h
index 574f49da693f..1b710674630c 100644
--- a/drivers/net/ethernet/ti/cpsw.h
+++ b/drivers/net/ethernet/ti/cpsw.h
@@ -15,6 +15,7 @@
 #define __CPSW_H__
 
 #include <linux/if_ether.h>
+#include <linux/phy.h>
 
 struct cpsw_slave_data {
 	char		phy_id[MII_BUS_ID_SIZE];
-- 
2.1.0

[PATCH RESEND v6 4/7] net: cpsw: Replace pr_err by dev_err

[Markus Pargmann]

Use dev_err instead of pr_err.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
---
 drivers/net/ethernet/ti/cpsw.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c
index f09b4639ad31..0bc2c2a2c236 100644
--- a/drivers/net/ethernet/ti/cpsw.c
+++ b/drivers/net/ethernet/ti/cpsw.c
@@ -1921,7 +1921,7 @@ static int cpsw_probe_dt(struct cpsw_platform_data *data,
 		mdio = of_find_device_by_node(mdio_node);
 		of_node_put(mdio_node);
 		if (!mdio) {
-			pr_err("Missing mdio platform device\n");
+			dev_err(&pdev->dev, "Missing mdio platform device\n");
 			return -EINVAL;
 		}
 		snprintf(slave_data->phy_id, sizeof(slave_data->phy_id),
-- 
2.1.0

[PATCH RESEND v6 4/7] net: cpsw: Replace pr_err by dev_err

[Markus Pargmann]

Use dev_err instead of pr_err.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
---
 drivers/net/ethernet/ti/cpsw.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c
index f09b4639ad31..0bc2c2a2c236 100644
--- a/drivers/net/ethernet/ti/cpsw.c
+++ b/drivers/net/ethernet/ti/cpsw.c
@@ -1921,7 +1921,7 @@ static int cpsw_probe_dt(struct cpsw_platform_data *data,
 		mdio = of_find_device_by_node(mdio_node);
 		of_node_put(mdio_node);
 		if (!mdio) {
-			pr_err("Missing mdio platform device\n");
+			dev_err(&pdev->dev, "Missing mdio platform device\n");
 			return -EINVAL;
 		}
 		snprintf(slave_data->phy_id, sizeof(slave_data->phy_id),
-- 
2.1.0

[PATCH RESEND v6 5/7] net: cpsw: Add am33xx MACID readout

[Markus Pargmann]

This patch adds a function to get the MACIDs from the am33xx SoC
control module registers which hold unique vendor MACIDs. This is only
used if of_get_mac_address() fails to get a valid mac address.

Signed-off-by: Markus Pargmann <mpa-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
Reviewed-by: Wolfram Sang <wsa-z923LK4zBo2bacvFa/9K2g@public.gmane.org>
Tested-by: Steven Rostedt <rostedt-nx8X9YLhiw1AfugRpC6u6w@public.gmane.org>
Acked-by: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
---

Notes:
    Changes in v6:
     - Move machine check outside of cpsw_am33xx_cm_get_macid()
    
    Changes in v5:
     - Fixed indention

 Documentation/devicetree/bindings/net/cpsw.txt |  4 +++
 drivers/net/ethernet/ti/Kconfig                |  2 ++
 drivers/net/ethernet/ti/cpsw.c                 | 42 +++++++++++++++++++++++++-
 3 files changed, 47 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt
index 107caf174a0e..33fe8462edf4 100644
--- a/Documentation/devicetree/bindings/net/cpsw.txt
+++ b/Documentation/devicetree/bindings/net/cpsw.txt
@@ -24,6 +24,8 @@ Optional properties:
 - ti,hwmods		: Must be "cpgmac0"
 - no_bd_ram		: Must be 0 or 1
 - dual_emac		: Specifies Switch to act as Dual EMAC
+- syscon		: Phandle to the system control device node, which is
+			  the control module device of the am33x
 
 Slave Properties:
 Required properties:
@@ -57,6 +59,7 @@ Examples:
 		active_slave = <0>;
 		cpts_clock_mult = <0x80000000>;
 		cpts_clock_shift = <29>;
+		syscon = <&cm>;
 		cpsw_emac0: slave@0 {
 			phy_id = <&davinci_mdio>, <0>;
 			phy-mode = "rgmii-txid";
@@ -85,6 +88,7 @@ Examples:
 		active_slave = <0>;
 		cpts_clock_mult = <0x80000000>;
 		cpts_clock_shift = <29>;
+		syscon = <&cm>;
 		cpsw_emac0: slave@0 {
 			phy_id = <&davinci_mdio>, <0>;
 			phy-mode = "rgmii-txid";
diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig
index 1769700a6070..5d8cb7956113 100644
--- a/drivers/net/ethernet/ti/Kconfig
+++ b/drivers/net/ethernet/ti/Kconfig
@@ -62,6 +62,8 @@ config TI_CPSW
 	select TI_DAVINCI_CPDMA
 	select TI_DAVINCI_MDIO
 	select TI_CPSW_PHY_SEL
+	select MFD_SYSCON
+	select REGMAP
 	---help---
 	  This driver supports TI's CPSW Ethernet Switch.
 
diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c
index 0bc2c2a2c236..12497d921fa6 100644
--- a/drivers/net/ethernet/ti/cpsw.c
+++ b/drivers/net/ethernet/ti/cpsw.c
@@ -33,6 +33,8 @@
 #include <linux/of_net.h>
 #include <linux/of_device.h>
 #include <linux/if_vlan.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
 
 #include <linux/pinctrl/consumer.h>
 
@@ -1816,6 +1818,36 @@ static void cpsw_slave_init(struct cpsw_slave *slave, struct cpsw_priv *priv,
 	slave->port_vlan = data->dual_emac_res_vlan;
 }
 
+#define AM33XX_CTRL_MAC_LO_REG(id) (0x630 + 0x8 * id)
+#define AM33XX_CTRL_MAC_HI_REG(id) (0x630 + 0x8 * id + 0x4)
+
+static int cpsw_am33xx_cm_get_macid(struct device *dev, int slave,
+		u8 *mac_addr)
+{
+	u32 macid_lo;
+	u32 macid_hi;
+	struct regmap *syscon;
+
+	syscon = syscon_regmap_lookup_by_phandle(dev->of_node, "syscon");
+	if (IS_ERR(syscon)) {
+		if (PTR_ERR(syscon) == -ENODEV)
+			return 0;
+		return PTR_ERR(syscon);
+	}
+
+	regmap_read(syscon, AM33XX_CTRL_MAC_LO_REG(slave), &macid_lo);
+	regmap_read(syscon, AM33XX_CTRL_MAC_HI_REG(slave), &macid_hi);
+
+	mac_addr[5] = (macid_lo >> 8) & 0xff;
+	mac_addr[4] = macid_lo & 0xff;
+	mac_addr[3] = (macid_hi >> 24) & 0xff;
+	mac_addr[2] = (macid_hi >> 16) & 0xff;
+	mac_addr[1] = (macid_hi >> 8) & 0xff;
+	mac_addr[0] = macid_hi & 0xff;
+
+	return 0;
+}
+
 static int cpsw_probe_dt(struct cpsw_platform_data *data,
 			 struct platform_device *pdev)
 {
@@ -1928,8 +1960,16 @@ static int cpsw_probe_dt(struct cpsw_platform_data *data,
 			 PHY_ID_FMT, mdio->name, phyid);
 
 		mac_addr = of_get_mac_address(slave_node);
-		if (mac_addr)
+		if (mac_addr) {
 			memcpy(slave_data->mac_addr, mac_addr, ETH_ALEN);
+		} else {
+			if (of_machine_is_compatible("ti,am33xx")) {
+				ret = cpsw_am33xx_cm_get_macid(&pdev->dev, i,
+							slave_data->mac_addr);
+				if (ret)
+					return ret;
+			}
+		}
 
 		slave_data->phy_if = of_get_phy_mode(slave_node);
 		if (slave_data->phy_if < 0) {
-- 
2.1.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH RESEND v6 5/7] net: cpsw: Add am33xx MACID readout

[Markus Pargmann]

This patch adds a function to get the MACIDs from the am33xx SoC
control module registers which hold unique vendor MACIDs. This is only
used if of_get_mac_address() fails to get a valid mac address.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Tony Lindgren <tony@atomide.com>
---

Notes:
    Changes in v6:
     - Move machine check outside of cpsw_am33xx_cm_get_macid()
    
    Changes in v5:
     - Fixed indention

 Documentation/devicetree/bindings/net/cpsw.txt |  4 +++
 drivers/net/ethernet/ti/Kconfig                |  2 ++
 drivers/net/ethernet/ti/cpsw.c                 | 42 +++++++++++++++++++++++++-
 3 files changed, 47 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt
index 107caf174a0e..33fe8462edf4 100644
--- a/Documentation/devicetree/bindings/net/cpsw.txt
+++ b/Documentation/devicetree/bindings/net/cpsw.txt
@@ -24,6 +24,8 @@ Optional properties:
 - ti,hwmods		: Must be "cpgmac0"
 - no_bd_ram		: Must be 0 or 1
 - dual_emac		: Specifies Switch to act as Dual EMAC
+- syscon		: Phandle to the system control device node, which is
+			  the control module device of the am33x
 
 Slave Properties:
 Required properties:
@@ -57,6 +59,7 @@ Examples:
 		active_slave = <0>;
 		cpts_clock_mult = <0x80000000>;
 		cpts_clock_shift = <29>;
+		syscon = <&cm>;
 		cpsw_emac0: slave at 0 {
 			phy_id = <&davinci_mdio>, <0>;
 			phy-mode = "rgmii-txid";
@@ -85,6 +88,7 @@ Examples:
 		active_slave = <0>;
 		cpts_clock_mult = <0x80000000>;
 		cpts_clock_shift = <29>;
+		syscon = <&cm>;
 		cpsw_emac0: slave at 0 {
 			phy_id = <&davinci_mdio>, <0>;
 			phy-mode = "rgmii-txid";
diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig
index 1769700a6070..5d8cb7956113 100644
--- a/drivers/net/ethernet/ti/Kconfig
+++ b/drivers/net/ethernet/ti/Kconfig
@@ -62,6 +62,8 @@ config TI_CPSW
 	select TI_DAVINCI_CPDMA
 	select TI_DAVINCI_MDIO
 	select TI_CPSW_PHY_SEL
+	select MFD_SYSCON
+	select REGMAP
 	---help---
 	  This driver supports TI's CPSW Ethernet Switch.
 
diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c
index 0bc2c2a2c236..12497d921fa6 100644
--- a/drivers/net/ethernet/ti/cpsw.c
+++ b/drivers/net/ethernet/ti/cpsw.c
@@ -33,6 +33,8 @@
 #include <linux/of_net.h>
 #include <linux/of_device.h>
 #include <linux/if_vlan.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
 
 #include <linux/pinctrl/consumer.h>
 
@@ -1816,6 +1818,36 @@ static void cpsw_slave_init(struct cpsw_slave *slave, struct cpsw_priv *priv,
 	slave->port_vlan = data->dual_emac_res_vlan;
 }
 
+#define AM33XX_CTRL_MAC_LO_REG(id) (0x630 + 0x8 * id)
+#define AM33XX_CTRL_MAC_HI_REG(id) (0x630 + 0x8 * id + 0x4)
+
+static int cpsw_am33xx_cm_get_macid(struct device *dev, int slave,
+		u8 *mac_addr)
+{
+	u32 macid_lo;
+	u32 macid_hi;
+	struct regmap *syscon;
+
+	syscon = syscon_regmap_lookup_by_phandle(dev->of_node, "syscon");
+	if (IS_ERR(syscon)) {
+		if (PTR_ERR(syscon) == -ENODEV)
+			return 0;
+		return PTR_ERR(syscon);
+	}
+
+	regmap_read(syscon, AM33XX_CTRL_MAC_LO_REG(slave), &macid_lo);
+	regmap_read(syscon, AM33XX_CTRL_MAC_HI_REG(slave), &macid_hi);
+
+	mac_addr[5] = (macid_lo >> 8) & 0xff;
+	mac_addr[4] = macid_lo & 0xff;
+	mac_addr[3] = (macid_hi >> 24) & 0xff;
+	mac_addr[2] = (macid_hi >> 16) & 0xff;
+	mac_addr[1] = (macid_hi >> 8) & 0xff;
+	mac_addr[0] = macid_hi & 0xff;
+
+	return 0;
+}
+
 static int cpsw_probe_dt(struct cpsw_platform_data *data,
 			 struct platform_device *pdev)
 {
@@ -1928,8 +1960,16 @@ static int cpsw_probe_dt(struct cpsw_platform_data *data,
 			 PHY_ID_FMT, mdio->name, phyid);
 
 		mac_addr = of_get_mac_address(slave_node);
-		if (mac_addr)
+		if (mac_addr) {
 			memcpy(slave_data->mac_addr, mac_addr, ETH_ALEN);
+		} else {
+			if (of_machine_is_compatible("ti,am33xx")) {
+				ret = cpsw_am33xx_cm_get_macid(&pdev->dev, i,
+							slave_data->mac_addr);
+				if (ret)
+					return ret;
+			}
+		}
 
 		slave_data->phy_if = of_get_phy_mode(slave_node);
 		if (slave_data->phy_if < 0) {
-- 
2.1.0

[PATCH RESEND v6 6/7] am33xx: define syscon control module device node

[Markus Pargmann]

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/am33xx.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 3a0a161342ba..25e38b6ac376 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -132,6 +132,11 @@
 			};
 		};
 
+		cm: syscon@44e10000 {
+			compatible = "ti,am33xx-controlmodule", "syscon";
+			reg = <0x44e10000 0x800>;
+		};
+
 		intc: interrupt-controller@48200000 {
 			compatible = "ti,omap2-intc";
 			interrupt-controller;
-- 
2.1.0

[PATCH RESEND v6 6/7] am33xx: define syscon control module device node

[Markus Pargmann]

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/am33xx.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 3a0a161342ba..25e38b6ac376 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -132,6 +132,11 @@
 			};
 		};
 
+		cm: syscon at 44e10000 {
+			compatible = "ti,am33xx-controlmodule", "syscon";
+			reg = <0x44e10000 0x800>;
+		};
+
 		intc: interrupt-controller at 48200000 {
 			compatible = "ti,omap2-intc";
 			interrupt-controller;
-- 
2.1.0

[PATCH RESEND v6 7/7] arm: dts: am33xx, Add syscon phandle to cpsw node

[Markus Pargmann]

There are 2 MACIDs stored in the control module of the am33xx. These are
read by the cpsw driver if no valid MACID was found in the devicetree.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/am33xx.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 25e38b6ac376..13e44b0f5adc 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -701,6 +701,7 @@
 			 */
 			interrupts = <40 41 42 43>;
 			ranges;
+			syscon = <&cm>;
 			status = "disabled";
 
 			davinci_mdio: mdio@4a101000 {
-- 
2.1.0

[PATCH RESEND v6 7/7] arm: dts: am33xx, Add syscon phandle to cpsw node

[Markus Pargmann]

There are 2 MACIDs stored in the control module of the am33xx. These are
read by the cpsw driver if no valid MACID was found in the devicetree.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/am33xx.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 25e38b6ac376..13e44b0f5adc 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -701,6 +701,7 @@
 			 */
 			interrupts = <40 41 42 43>;
 			ranges;
+			syscon = <&cm>;
 			status = "disabled";
 
 			davinci_mdio: mdio at 4a101000 {
-- 
2.1.0

Re: [PATCH RESEND v6 0/7] net: cpsw: Support for am335x chip MACIDs

[Mugunthan V N]

On Monday 29 September 2014 12:23 PM, Markus Pargmann wrote:
> Hi,
> 
> Another resend of this series to add the netdev list.
> 
> This series adds support to the cpsw driver to read the MACIDs of the am335x
> chip and use them as fallback. These addresses are only used if there are no
> mac addresses in the devicetree, for example set by a bootloader.
> 
> Best regards,
> 
> Markus
> 
> 
> Markus Pargmann (7):
>   DT doc: net: cpsw mac-address is optional
>   net: cpsw: Add missing return value
>   net: cpsw: header, Add missing include
>   net: cpsw: Replace pr_err by dev_err
>   net: cpsw: Add am33xx MACID readout
>   am33xx: define syscon control module device node
>   arm: dts: am33xx, Add syscon phandle to cpsw node
> 
>  Documentation/devicetree/bindings/net/cpsw.txt |  6 +++-
>  arch/arm/boot/dts/am33xx.dtsi                  |  6 ++++
>  drivers/net/ethernet/ti/Kconfig                |  2 ++
>  drivers/net/ethernet/ti/cpsw.c                 | 45 ++++++++++++++++++++++++--
>  drivers/net/ethernet/ti/cpsw.h                 |  1 +
>  5 files changed, 57 insertions(+), 3 deletions(-)
> 

Acked-by: Mugunthan V N <mugunthanvnm@gmail.com>

Regards
Mugunthan V N

[PATCH RESEND v6 0/7] net: cpsw: Support for am335x chip MACIDs

[Mugunthan V N]

On Monday 29 September 2014 12:23 PM, Markus Pargmann wrote:
> Hi,
> 
> Another resend of this series to add the netdev list.
> 
> This series adds support to the cpsw driver to read the MACIDs of the am335x
> chip and use them as fallback. These addresses are only used if there are no
> mac addresses in the devicetree, for example set by a bootloader.
> 
> Best regards,
> 
> Markus
> 
> 
> Markus Pargmann (7):
>   DT doc: net: cpsw mac-address is optional
>   net: cpsw: Add missing return value
>   net: cpsw: header, Add missing include
>   net: cpsw: Replace pr_err by dev_err
>   net: cpsw: Add am33xx MACID readout
>   am33xx: define syscon control module device node
>   arm: dts: am33xx, Add syscon phandle to cpsw node
> 
>  Documentation/devicetree/bindings/net/cpsw.txt |  6 +++-
>  arch/arm/boot/dts/am33xx.dtsi                  |  6 ++++
>  drivers/net/ethernet/ti/Kconfig                |  2 ++
>  drivers/net/ethernet/ti/cpsw.c                 | 45 ++++++++++++++++++++++++--
>  drivers/net/ethernet/ti/cpsw.h                 |  1 +
>  5 files changed, 57 insertions(+), 3 deletions(-)
> 

Acked-by: Mugunthan V N <mugunthanvnm@gmail.com>

Regards
Mugunthan V N

Re: [PATCH RESEND v6 0/7] net: cpsw: Support for am335x chip MACIDs

[David Miller]

From: Markus Pargmann <mpa@pengutronix.de>
Date: Mon, 29 Sep 2014 08:53:12 +0200

> Another resend of this series to add the netdev list.
> 
> This series adds support to the cpsw driver to read the MACIDs of the am335x
> chip and use them as fallback. These addresses are only used if there are no
> mac addresses in the devicetree, for example set by a bootloader.

Series applied to net-next, thanks.

[PATCH RESEND v6 0/7] net: cpsw: Support for am335x chip MACIDs

[David Miller]

From: Markus Pargmann <mpa@pengutronix.de>
Date: Mon, 29 Sep 2014 08:53:12 +0200

> Another resend of this series to add the netdev list.
> 
> This series adds support to the cpsw driver to read the MACIDs of the am335x
> chip and use them as fallback. These addresses are only used if there are no
> mac addresses in the devicetree, for example set by a bootloader.

Series applied to net-next, thanks.