[U-Boot] [PATCH 0/7] avr32: remove non-generic boards

[U-Boot] [PATCH 0/7] avr32: remove non-generic boards

[Andreas Bießmann]

This series deletes avr32-boards that are still using the ancient
arch/avr32/lib/board.c code. If one would like his board to stay in u-boot
there is a last chance to convert it to generic board _now_. It should be as easy
as defining these three values in the board config:

|/* generic board */
|#define CONFIG_SYS_GENERIC_BOARD
|#define CONFIG_BOARD_EARLY_INIT_F
|#define CONFIG_BOARD_EARLY_INIT_R


The patch 'avr32: delete non generic board favr-32-ezkit' has an checkpatch
warning which will not be fixed.

---8<---
0 errors, 1 warnings, 0 checks for 0002-avr32-delete-non-generic-board-favr-32-ezkit.patch:
warning: arch/avr32/Kconfig,22: please write a paragraph that describes the config symbol fully
--->8---


The patch 'avr32: delete non generic board's atstk100{3,4,6}' has a checkpatch
warning wich will not be fixed.

---8<---
0 errors, 1 warnings, 0 checks for 0005-avr32-delete-non-generic-board-s-atstk100-3-4-6.patch:
warning: arch/avr32/Kconfig,13: please write a paragraph that describes the config symbol fully
--->8---



Andreas Bie?mann (7):
  avr32: delete non generic board atngw100
  avr32: delete non generic board favr-32-ezkit
  avr32: delete non generic board hammerhead
  avr32: delete non generic board mimc200
  avr32: delete non generic board's atstk100{3,4,6}
  avr32: take maintainership for atstk1002
  avr32: delete ancient board.c

 arch/avr32/Kconfig                           |  25 ---
 arch/avr32/lib/Makefile                      |   3 -
 arch/avr32/lib/board.c                       | 256 ---------------------------
 board/atmel/atngw100/Kconfig                 |  15 --
 board/atmel/atngw100/MAINTAINERS             |   6 -
 board/atmel/atngw100/Makefile                |   6 -
 board/atmel/atngw100/atngw100.c              | 109 ------------
 board/atmel/atstk1000/Kconfig                |  48 -----
 board/atmel/atstk1000/MAINTAINERS            |  10 +-
 board/atmel/atstk1000/atstk1000.c            |  23 +--
 board/earthlcd/favr-32-ezkit/Kconfig         |  15 --
 board/earthlcd/favr-32-ezkit/MAINTAINERS     |   6 -
 board/earthlcd/favr-32-ezkit/Makefile        |   9 -
 board/earthlcd/favr-32-ezkit/favr-32-ezkit.c |  81 ---------
 board/earthlcd/favr-32-ezkit/flash.c         | 216 ----------------------
 board/mimc/mimc200/Kconfig                   |  15 --
 board/mimc/mimc200/MAINTAINERS               |   6 -
 board/mimc/mimc200/Makefile                  |   6 -
 board/mimc/mimc200/mimc200.c                 | 197 ---------------------
 board/miromico/hammerhead/Kconfig            |  15 --
 board/miromico/hammerhead/MAINTAINERS        |   6 -
 board/miromico/hammerhead/Makefile           |   6 -
 board/miromico/hammerhead/hammerhead.c       |  91 ----------
 configs/atngw100_defconfig                   |   2 -
 configs/atstk1003_defconfig                  |   2 -
 configs/atstk1004_defconfig                  |   2 -
 configs/atstk1006_defconfig                  |   2 -
 configs/favr-32-ezkit_defconfig              |   2 -
 configs/hammerhead_defconfig                 |   2 -
 configs/mimc200_defconfig                    |   2 -
 include/configs/atngw100.h                   | 163 -----------------
 include/configs/atstk1003.h                  | 161 -----------------
 include/configs/atstk1004.h                  | 161 -----------------
 include/configs/atstk1006.h                  | 178 -------------------
 include/configs/favr-32-ezkit.h              | 181 -------------------
 include/configs/hammerhead.h                 | 157 ----------------
 include/configs/mimc200.h                    | 177 ------------------
 37 files changed, 3 insertions(+), 2359 deletions(-)
 delete mode 100644 arch/avr32/lib/board.c
 delete mode 100644 board/atmel/atngw100/Kconfig
 delete mode 100644 board/atmel/atngw100/MAINTAINERS
 delete mode 100644 board/atmel/atngw100/Makefile
 delete mode 100644 board/atmel/atngw100/atngw100.c
 delete mode 100644 board/earthlcd/favr-32-ezkit/Kconfig
 delete mode 100644 board/earthlcd/favr-32-ezkit/MAINTAINERS
 delete mode 100644 board/earthlcd/favr-32-ezkit/Makefile
 delete mode 100644 board/earthlcd/favr-32-ezkit/favr-32-ezkit.c
 delete mode 100644 board/earthlcd/favr-32-ezkit/flash.c
 delete mode 100644 board/mimc/mimc200/Kconfig
 delete mode 100644 board/mimc/mimc200/MAINTAINERS
 delete mode 100644 board/mimc/mimc200/Makefile
 delete mode 100644 board/mimc/mimc200/mimc200.c
 delete mode 100644 board/miromico/hammerhead/Kconfig
 delete mode 100644 board/miromico/hammerhead/MAINTAINERS
 delete mode 100644 board/miromico/hammerhead/Makefile
 delete mode 100644 board/miromico/hammerhead/hammerhead.c
 delete mode 100644 configs/atngw100_defconfig
 delete mode 100644 configs/atstk1003_defconfig
 delete mode 100644 configs/atstk1004_defconfig
 delete mode 100644 configs/atstk1006_defconfig
 delete mode 100644 configs/favr-32-ezkit_defconfig
 delete mode 100644 configs/hammerhead_defconfig
 delete mode 100644 configs/mimc200_defconfig
 delete mode 100644 include/configs/atngw100.h
 delete mode 100644 include/configs/atstk1003.h
 delete mode 100644 include/configs/atstk1004.h
 delete mode 100644 include/configs/atstk1006.h
 delete mode 100644 include/configs/favr-32-ezkit.h
 delete mode 100644 include/configs/hammerhead.h
 delete mode 100644 include/configs/mimc200.h

-- 
2.1.4

[U-Boot] [PATCH 1/7] avr32: delete non generic board atngw100

[Andreas Bießmann]

Signed-off-by: Andreas Bie?mann <andreas.devel@googlemail.com>
---

 arch/avr32/Kconfig               |   4 -
 board/atmel/atngw100/Kconfig     |  15 ----
 board/atmel/atngw100/MAINTAINERS |   6 --
 board/atmel/atngw100/Makefile    |   6 --
 board/atmel/atngw100/atngw100.c  | 109 --------------------------
 configs/atngw100_defconfig       |   2 -
 include/configs/atngw100.h       | 163 ---------------------------------------
 7 files changed, 305 deletions(-)
 delete mode 100644 board/atmel/atngw100/Kconfig
 delete mode 100644 board/atmel/atngw100/MAINTAINERS
 delete mode 100644 board/atmel/atngw100/Makefile
 delete mode 100644 board/atmel/atngw100/atngw100.c
 delete mode 100644 configs/atngw100_defconfig
 delete mode 100644 include/configs/atngw100.h

diff --git a/arch/avr32/Kconfig b/arch/avr32/Kconfig
index 66de2ad..e4b37bc 100644
--- a/arch/avr32/Kconfig
+++ b/arch/avr32/Kconfig
@@ -7,9 +7,6 @@ config SYS_ARCH
 choice
 	prompt "Target select"
 
-config TARGET_ATNGW100
-	bool "Support atngw100"
-
 config TARGET_ATNGW100MKII
 	bool "Support atngw100mkii"
 
@@ -39,7 +36,6 @@ config TARGET_HAMMERHEAD
 
 endchoice
 
-source "board/atmel/atngw100/Kconfig"
 source "board/atmel/atngw100mkii/Kconfig"
 source "board/atmel/atstk1000/Kconfig"
 source "board/earthlcd/favr-32-ezkit/Kconfig"
diff --git a/board/atmel/atngw100/Kconfig b/board/atmel/atngw100/Kconfig
deleted file mode 100644
index 28037b6..0000000
--- a/board/atmel/atngw100/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_ATNGW100
-
-config SYS_BOARD
-	default "atngw100"
-
-config SYS_VENDOR
-	default "atmel"
-
-config SYS_SOC
-	default "at32ap700x"
-
-config SYS_CONFIG_NAME
-	default "atngw100"
-
-endif
diff --git a/board/atmel/atngw100/MAINTAINERS b/board/atmel/atngw100/MAINTAINERS
deleted file mode 100644
index 1c319f6..0000000
--- a/board/atmel/atngw100/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-ATNGW100 BOARD
-#M:	Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
-S:	Orphan (since 2014-06)
-F:	board/atmel/atngw100/
-F:	include/configs/atngw100.h
-F:	configs/atngw100_defconfig
diff --git a/board/atmel/atngw100/Makefile b/board/atmel/atngw100/Makefile
deleted file mode 100644
index f9b93c9..0000000
--- a/board/atmel/atngw100/Makefile
+++ /dev/null
@@ -1,6 +0,0 @@
-#
-# Copyright (C) 2005-2006 Atmel Corporation
-#
-# SPDX-License-Identifier:	GPL-2.0+
-
-obj-y	:= atngw100.o
diff --git a/board/atmel/atngw100/atngw100.c b/board/atmel/atngw100/atngw100.c
deleted file mode 100644
index dacd427..0000000
--- a/board/atmel/atngw100/atngw100.c
+++ /dev/null
@@ -1,109 +0,0 @@
-/*
- * Copyright (C) 2006 Atmel Corporation
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-#include <common.h>
-
-#include <asm/io.h>
-#include <asm/sdram.h>
-#include <asm/arch/clk.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/hmatrix.h>
-#include <asm/arch/mmu.h>
-#include <asm/arch/portmux.h>
-#include <netdev.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = {
-	{
-		.virt_pgno	= CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT,
-		.nr_pages	= CONFIG_SYS_FLASH_SIZE >> MMU_PAGE_SHIFT,
-		.phys		= (CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT)
-					| MMU_VMR_CACHE_NONE,
-	}, {
-		.virt_pgno	= CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT,
-		.nr_pages	= EBI_SDRAM_SIZE >> MMU_PAGE_SHIFT,
-		.phys		= (CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT)
-					| MMU_VMR_CACHE_WRBACK,
-	},
-};
-
-static const struct sdram_config sdram_config = {
-	.data_bits	= SDRAM_DATA_16BIT,
-	.row_bits	= 13,
-	.col_bits	= 9,
-	.bank_bits	= 2,
-	.cas		= 3,
-	.twr		= 2,
-	.trc		= 7,
-	.trp		= 2,
-	.trcd		= 2,
-	.tras		= 5,
-	.txsr		= 5,
-	/* 7.81 us */
-	.refresh_period	= (781 * (SDRAMC_BUS_HZ / 1000)) / 100000,
-};
-
-int board_early_init_f(void)
-{
-	/* Enable SDRAM in the EBI mux */
-	hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE));
-
-	portmux_enable_ebi(16, 23, 0, PORTMUX_DRIVE_HIGH);
-	sdram_init(uncached(EBI_SDRAM_BASE), &sdram_config);
-
-	portmux_enable_usart1(PORTMUX_DRIVE_MIN);
-
-#if defined(CONFIG_MACB)
-	portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH);
-	portmux_enable_macb1(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH);
-#endif
-#if defined(CONFIG_MMC)
-	portmux_enable_mmci(0, PORTMUX_MMCI_4BIT, PORTMUX_DRIVE_LOW);
-#endif
-#if defined(CONFIG_ATMEL_SPI)
-	portmux_enable_spi0(1 << 0, PORTMUX_DRIVE_LOW);
-#endif
-
-	return 0;
-}
-
-int board_early_init_r(void)
-{
-	gd->bd->bi_phy_id[0] = 0x01;
-	gd->bd->bi_phy_id[1] = 0x03;
-	return 0;
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bi)
-{
-	macb_eth_initialize(0, (void *)ATMEL_BASE_MACB0, bi->bi_phy_id[0]);
-	macb_eth_initialize(1, (void *)ATMEL_BASE_MACB1, bi->bi_phy_id[1]);
-	return 0;
-}
-#endif
-
-/* SPI chip select control */
-#ifdef CONFIG_ATMEL_SPI
-#include <spi.h>
-
-#define ATNGW100_DATAFLASH_CS_PIN	GPIO_PIN_PA(3)
-
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
-	return bus == 0 && cs == 0;
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
-	gpio_set_value(ATNGW100_DATAFLASH_CS_PIN, 0);
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
-	gpio_set_value(ATNGW100_DATAFLASH_CS_PIN, 1);
-}
-#endif /* CONFIG_ATMEL_SPI */
diff --git a/configs/atngw100_defconfig b/configs/atngw100_defconfig
deleted file mode 100644
index cd79990..0000000
--- a/configs/atngw100_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_AVR32=y
-CONFIG_TARGET_ATNGW100=y
diff --git a/include/configs/atngw100.h b/include/configs/atngw100.h
deleted file mode 100644
index 540e86a..0000000
--- a/include/configs/atngw100.h
+++ /dev/null
@@ -1,163 +0,0 @@
-/*
- * Copyright (C) 2006 Atmel Corporation
- *
- * Configuration settings for the AVR32 Network Gateway
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/hardware.h>
-
-#define CONFIG_AT32AP
-#define CONFIG_AT32AP7000
-#define CONFIG_ATNGW100
-
-/*
- * Set up the PLL to run at 140 MHz, the CPU to run at the PLL
- * frequency, the HSB and PBB busses to run at 1/2 the PLL frequency
- * and the PBA bus to run at 1/4 the PLL frequency.
- */
-#define CONFIG_PLL
-#define CONFIG_SYS_POWER_MANAGER
-#define CONFIG_SYS_OSC0_HZ			20000000
-#define CONFIG_SYS_PLL0_DIV			1
-#define CONFIG_SYS_PLL0_MUL			7
-#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES	16
-#define CONFIG_SYS_CLKDIV_CPU			0
-#define CONFIG_SYS_CLKDIV_HSB			1
-#define CONFIG_SYS_CLKDIV_PBA			2
-#define CONFIG_SYS_CLKDIV_PBB			1
-
-/* Reserve VM regions for SDRAM and NOR flash */
-#define CONFIG_SYS_NR_VM_REGIONS		2
-
-/*
- * The PLLOPT register controls the PLL like this:
- *   icp = PLLOPT<2>
- *   ivco = PLLOPT<1:0>
- *
- * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz).
- */
-#define CONFIG_SYS_PLL0_OPT			0x04
-
-#define CONFIG_USART_BASE		ATMEL_BASE_USART1
-#define CONFIG_USART_ID			1
-/* User serviceable stuff */
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-#define CONFIG_STACKSIZE		(2048)
-
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_BOOTARGS							\
-	"console=ttyS0 root=/dev/mtdblock1 rootfstype=jffs2"
-#define CONFIG_BOOTCOMMAND						\
-	"fsload; bootm"
-
-/*
- * Only interrupt autoboot if <space> is pressed. Otherwise, garbage
- * data on the serial line may interrupt the boot sequence.
- */
-#define CONFIG_BOOTDELAY		1
-#define CONFIG_AUTOBOOT
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT		\
-	"Press SPACE to abort autoboot in %d seconds\n", bootdelay
-#define CONFIG_AUTOBOOT_DELAY_STR	"d"
-#define CONFIG_AUTOBOOT_STOP_STR	" "
-
-/*
- * After booting the board for the first time, new ethernet addresses
- * should be generated and assigned to the environment variables
- * "ethaddr" and "eth1addr". This is normally done during production.
- */
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-
-/*
- * BOOTP/DHCP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MMC
-#define CONFIG_CMD_SF
-#define CONFIG_CMD_SPI
-
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_SETGETDCR
-#undef CONFIG_CMD_SOURCE
-#undef CONFIG_CMD_XIMG
-
-#define CONFIG_ATMEL_USART
-#define CONFIG_MACB
-#define CONFIG_PORTMUX_PIO
-#define CONFIG_SYS_NR_PIOS			5
-#define CONFIG_SYS_HSDRAMC
-#define CONFIG_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#define CONFIG_GENERIC_MMC
-#define CONFIG_ATMEL_SPI
-
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_ATMEL
-
-#define CONFIG_SYS_DCACHE_LINESZ		32
-#define CONFIG_SYS_ICACHE_LINESZ		32
-
-#define CONFIG_NR_DRAM_BANKS		1
-
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-
-#define CONFIG_SYS_FLASH_BASE			0x00000000
-#define CONFIG_SYS_FLASH_SIZE			0x800000
-#define CONFIG_SYS_MAX_FLASH_BANKS		1
-#define CONFIG_SYS_MAX_FLASH_SECT		135
-
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_TEXT_BASE		0x00000000
-
-#define CONFIG_SYS_INTRAM_BASE			INTERNAL_SRAM_BASE
-#define CONFIG_SYS_INTRAM_SIZE			INTERNAL_SRAM_SIZE
-#define CONFIG_SYS_SDRAM_BASE			EBI_SDRAM_BASE
-
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SIZE			65536
-#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE)
-
-#define CONFIG_SYS_MALLOC_LEN			(256*1024)
-
-/* Allow 4MB for the kernel run-time image */
-#define CONFIG_SYS_LOAD_ADDR			(EBI_SDRAM_BASE + 0x00400000)
-#define CONFIG_SYS_BOOTPARAMS_LEN		(16 * 1024)
-
-/* Other configuration settings that shouldn't have to change all that often */
-#define CONFIG_SYS_PROMPT			"U-Boot> "
-#define CONFIG_SYS_CBSIZE			256
-#define CONFIG_SYS_MAXARGS			16
-#define CONFIG_SYS_PBSIZE			(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-
-#define CONFIG_SYS_MEMTEST_START		EBI_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_END			(CONFIG_SYS_MEMTEST_START + 0x1f00000)
-
-#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 }
-
-#endif /* __CONFIG_H */
-- 
2.1.4

[U-Boot] [PATCH 2/7] avr32: delete non generic board favr-32-ezkit

[Andreas Bießmann]

Signed-off-by: Andreas Bie?mann <andreas.devel@googlemail.com>
---

 arch/avr32/Kconfig                           |   4 -
 board/earthlcd/favr-32-ezkit/Kconfig         |  15 --
 board/earthlcd/favr-32-ezkit/MAINTAINERS     |   6 -
 board/earthlcd/favr-32-ezkit/Makefile        |   9 --
 board/earthlcd/favr-32-ezkit/favr-32-ezkit.c |  81 ----------
 board/earthlcd/favr-32-ezkit/flash.c         | 216 ---------------------------
 configs/favr-32-ezkit_defconfig              |   2 -
 include/configs/favr-32-ezkit.h              | 181 ----------------------
 8 files changed, 514 deletions(-)
 delete mode 100644 board/earthlcd/favr-32-ezkit/Kconfig
 delete mode 100644 board/earthlcd/favr-32-ezkit/MAINTAINERS
 delete mode 100644 board/earthlcd/favr-32-ezkit/Makefile
 delete mode 100644 board/earthlcd/favr-32-ezkit/favr-32-ezkit.c
 delete mode 100644 board/earthlcd/favr-32-ezkit/flash.c
 delete mode 100644 configs/favr-32-ezkit_defconfig
 delete mode 100644 include/configs/favr-32-ezkit.h

diff --git a/arch/avr32/Kconfig b/arch/avr32/Kconfig
index e4b37bc..aa08d3e 100644
--- a/arch/avr32/Kconfig
+++ b/arch/avr32/Kconfig
@@ -22,9 +22,6 @@ config TARGET_ATSTK1004
 config TARGET_ATSTK1006
 	bool "Support atstk1006"
 
-config TARGET_FAVR_32_EZKIT
-	bool "Support favr-32-ezkit"
-
 config TARGET_GRASSHOPPER
 	bool "Support grasshopper"
 
@@ -38,7 +35,6 @@ endchoice
 
 source "board/atmel/atngw100mkii/Kconfig"
 source "board/atmel/atstk1000/Kconfig"
-source "board/earthlcd/favr-32-ezkit/Kconfig"
 source "board/in-circuit/grasshopper/Kconfig"
 source "board/mimc/mimc200/Kconfig"
 source "board/miromico/hammerhead/Kconfig"
diff --git a/board/earthlcd/favr-32-ezkit/Kconfig b/board/earthlcd/favr-32-ezkit/Kconfig
deleted file mode 100644
index 50e29ec..0000000
--- a/board/earthlcd/favr-32-ezkit/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_FAVR_32_EZKIT
-
-config SYS_BOARD
-	default "favr-32-ezkit"
-
-config SYS_VENDOR
-	default "earthlcd"
-
-config SYS_SOC
-	default "at32ap700x"
-
-config SYS_CONFIG_NAME
-	default "favr-32-ezkit"
-
-endif
diff --git a/board/earthlcd/favr-32-ezkit/MAINTAINERS b/board/earthlcd/favr-32-ezkit/MAINTAINERS
deleted file mode 100644
index 89ba862..0000000
--- a/board/earthlcd/favr-32-ezkit/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-FAVR-32-EZKIT BOARD
-#M:	Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
-S:	Orphan (since 2014-06)
-F:	board/earthlcd/favr-32-ezkit/
-F:	include/configs/favr-32-ezkit.h
-F:	configs/favr-32-ezkit_defconfig
diff --git a/board/earthlcd/favr-32-ezkit/Makefile b/board/earthlcd/favr-32-ezkit/Makefile
deleted file mode 100644
index f712ab9..0000000
--- a/board/earthlcd/favr-32-ezkit/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# Copyright (C) 2008 Atmel Corporation
-#
-# SPDX-License-Identifier:	GPL-2.0+
-
-obj-y	:= favr-32-ezkit.o flash.o
diff --git a/board/earthlcd/favr-32-ezkit/favr-32-ezkit.c b/board/earthlcd/favr-32-ezkit/favr-32-ezkit.c
deleted file mode 100644
index f9ac330..0000000
--- a/board/earthlcd/favr-32-ezkit/favr-32-ezkit.c
+++ /dev/null
@@ -1,81 +0,0 @@
-/*
- * Copyright (C) 2008 Atmel Corporation
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-#include <common.h>
-#include <netdev.h>
-
-#include <asm/io.h>
-#include <asm/sdram.h>
-#include <asm/arch/clk.h>
-#include <asm/arch/hmatrix.h>
-#include <asm/arch/mmu.h>
-#include <asm/arch/portmux.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = {
-	{
-		.virt_pgno	= CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT,
-		.nr_pages	= CONFIG_SYS_FLASH_SIZE >> MMU_PAGE_SHIFT,
-		.phys		= (CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT)
-					| MMU_VMR_CACHE_NONE,
-	}, {
-		.virt_pgno	= CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT,
-		.nr_pages	= EBI_SDRAM_SIZE >> MMU_PAGE_SHIFT,
-		.phys		= (CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT)
-					| MMU_VMR_CACHE_WRBACK,
-	},
-};
-
-static const struct sdram_config sdram_config = {
-	/* MT48LC4M32B2P-6 (16 MB) */
-	.data_bits	= SDRAM_DATA_32BIT,
-	.row_bits	= 12,
-	.col_bits	= 8,
-	.bank_bits	= 2,
-	.cas		= 3,
-	.twr		= 2,
-	.trc		= 7,
-	.trp		= 2,
-	.trcd		= 2,
-	.tras		= 5,
-	.txsr		= 5,
-	/* 15.6 us */
-	.refresh_period	= (156 * (SDRAMC_BUS_HZ / 1000)) / 10000,
-};
-
-int board_early_init_f(void)
-{
-	/* Enable SDRAM in the EBI mux */
-	hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE));
-
-	portmux_enable_ebi(32, 23, 0, PORTMUX_DRIVE_HIGH);
-
-	sdram_init(uncached(EBI_SDRAM_BASE), &sdram_config);
-
-	portmux_enable_usart3(PORTMUX_DRIVE_MIN);
-#if defined(CONFIG_MACB)
-	portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH);
-#endif
-#if defined(CONFIG_MMC)
-	portmux_enable_mmci(0, PORTMUX_MMCI_4BIT, PORTMUX_DRIVE_LOW);
-#endif
-
-	return 0;
-}
-
-int board_early_init_r(void)
-{
-	gd->bd->bi_phy_id[0] = 0x01;
-	return 0;
-}
-
-#if defined(CONFIG_MACB) && defined(CONFIG_CMD_NET)
-int board_eth_init(bd_t *bi)
-{
-	return macb_eth_initialize(0, (void *)ATMEL_BASE_MACB0,
-		bi->bi_phy_id[0]);
-}
-#endif
diff --git a/board/earthlcd/favr-32-ezkit/flash.c b/board/earthlcd/favr-32-ezkit/flash.c
deleted file mode 100644
index e45c6f4..0000000
--- a/board/earthlcd/favr-32-ezkit/flash.c
+++ /dev/null
@@ -1,216 +0,0 @@
-/*
- * Copyright (C) 2008 Atmel Corporation
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-#include <common.h>
-
-#ifdef CONFIG_FAVR32_EZKIT_EXT_FLASH
-#include <asm/arch/cacheflush.h>
-#include <asm/io.h>
-#include <asm/sections.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-flash_info_t flash_info[1];
-
-static void flash_identify(uint16_t *flash, flash_info_t *info)
-{
-	unsigned long flags;
-
-	flags = disable_interrupts();
-
-	dcache_flush_unlocked();
-
-	writew(0xaa, flash + 0x555);
-	writew(0x55, flash + 0xaaa);
-	writew(0x90, flash + 0x555);
-	info->flash_id = readl(flash);
-	writew(0xff, flash);
-
-	readw(flash);
-
-	if (flags)
-		enable_interrupts();
-}
-
-unsigned long flash_init(void)
-{
-	unsigned long addr;
-	unsigned int i;
-
-	flash_info[0].size = CONFIG_SYS_FLASH_SIZE;
-	flash_info[0].sector_count = 135;
-
-	flash_identify(uncached((void *)CONFIG_SYS_FLASH_BASE), &flash_info[0]);
-
-	for (i = 0, addr = 0; i < 8; i++, addr += 0x2000)
-		flash_info[0].start[i] = addr;
-	for (; i < flash_info[0].sector_count; i++, addr += 0x10000)
-		flash_info[0].start[i] = addr;
-
-	return CONFIG_SYS_FLASH_SIZE;
-}
-
-void flash_print_info(flash_info_t *info)
-{
-	printf("Flash: Vendor ID: 0x%02lx, Product ID: 0x%02lx\n",
-	       info->flash_id >> 16, info->flash_id & 0xffff);
-	printf("Size: %ld MB in %d sectors\n",
-	       info->size >> 10, info->sector_count);
-}
-
-int flash_erase(flash_info_t *info, int s_first, int s_last)
-{
-	unsigned long flags;
-	unsigned long start_time;
-	uint16_t *fb, *sb;
-	unsigned int i;
-	int ret;
-	uint16_t status;
-
-	if ((s_first < 0) || (s_first > s_last)
-	    || (s_last >= info->sector_count)) {
-		puts("Error: first and/or last sector out of range\n");
-		return ERR_INVAL;
-	}
-
-	for (i = s_first; i < s_last; i++)
-		if (info->protect[i]) {
-			printf("Error: sector %d is protected\n", i);
-			return ERR_PROTECTED;
-		}
-
-	fb = (uint16_t *)uncached(info->start[0]);
-
-	dcache_flush_unlocked();
-
-	for (i = s_first; (i <= s_last) && !ctrlc(); i++) {
-		printf("Erasing sector %3d...", i);
-
-		sb = (uint16_t *)uncached(info->start[i]);
-
-		flags = disable_interrupts();
-
-		start_time = get_timer(0);
-
-		/* Unlock sector */
-		writew(0xaa, fb + 0x555);
-		writew(0x70, sb);
-
-		/* Erase sector */
-		writew(0xaa, fb + 0x555);
-		writew(0x55, fb + 0xaaa);
-		writew(0x80, fb + 0x555);
-		writew(0xaa, fb + 0x555);
-		writew(0x55, fb + 0xaaa);
-		writew(0x30, sb);
-
-		/* Wait for completion */
-		ret = ERR_OK;
-		do {
-			/* TODO: Timeout */
-			status = readw(sb);
-		} while ((status != 0xffff) && !(status & 0x28));
-
-		writew(0xf0, fb);
-
-		/*
-		 * Make sure the command actually makes it to the bus
-		 * before we re-enable interrupts.
-		 */
-		readw(fb);
-
-		if (flags)
-			enable_interrupts();
-
-		if (status != 0xffff) {
-			printf("Flash erase error at address 0x%p: 0x%02x\n",
-			       sb, status);
-			ret = ERR_PROG_ERROR;
-			break;
-		}
-	}
-
-	if (ctrlc())
-		printf("User interrupt!\n");
-
-	return ERR_OK;
-}
-
-int write_buff(flash_info_t *info, uchar *src,
-			   ulong addr, ulong count)
-{
-	unsigned long flags;
-	uint16_t *base, *p, *s, *end;
-	uint16_t word, status, status1;
-	int ret = ERR_OK;
-
-	if (addr < info->start[0]
-	    || (addr + count) > (info->start[0] + info->size)
-	    || (addr + count) < addr) {
-		puts("Error: invalid address range\n");
-		return ERR_INVAL;
-	}
-
-	if (addr & 1 || count & 1 || (unsigned int)src & 1) {
-		puts("Error: misaligned source, destination or count\n");
-		return ERR_ALIGN;
-	}
-
-	base = (uint16_t *)uncached(info->start[0]);
-	end = (uint16_t *)uncached(addr + count);
-
-	flags = disable_interrupts();
-
-	dcache_flush_unlocked();
-	sync_write_buffer();
-
-	for (p = (uint16_t *)uncached(addr), s = (uint16_t *)src;
-	     p < end && !ctrlc(); p++, s++) {
-		word = *s;
-
-		writew(0xaa, base + 0x555);
-		writew(0x55, base + 0xaaa);
-		writew(0xa0, base + 0x555);
-		writew(word, p);
-
-		sync_write_buffer();
-
-		/* Wait for completion */
-		status1 = readw(p);
-		do {
-			/* TODO: Timeout */
-			status = status1;
-			status1 = readw(p);
-		} while (((status ^ status1) & 0x40)	/* toggled */
-			 && !(status1 & 0x28));		/* error bits */
-
-		/*
-		 * We'll need to check once again for toggle bit
-		 * because the toggle bit may stop toggling as I/O5
-		 * changes to "1" (ref at49bv642.pdf p9)
-		 */
-		status1 = readw(p);
-		status = readw(p);
-		if ((status ^ status1) & 0x40) {
-			printf("Flash write error@address 0x%p: "
-			       "0x%02x != 0x%02x\n",
-			       p, status,word);
-			ret = ERR_PROG_ERROR;
-			writew(0xf0, base);
-			readw(base);
-			break;
-		}
-
-		writew(0xf0, base);
-		readw(base);
-	}
-
-	if (flags)
-		enable_interrupts();
-
-	return ret;
-}
-
-#endif /* CONFIG_FAVR32_EZKIT_EXT_FLASH */
diff --git a/configs/favr-32-ezkit_defconfig b/configs/favr-32-ezkit_defconfig
deleted file mode 100644
index 941e028..0000000
--- a/configs/favr-32-ezkit_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_AVR32=y
-CONFIG_TARGET_FAVR_32_EZKIT=y
diff --git a/include/configs/favr-32-ezkit.h b/include/configs/favr-32-ezkit.h
deleted file mode 100644
index 75bff4c..0000000
--- a/include/configs/favr-32-ezkit.h
+++ /dev/null
@@ -1,181 +0,0 @@
-/*
- * Copyright (C) 2008 Atmel Corporation
- *
- * Configuration settings for the Favr-32 EarthLCD LCD kit.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/hardware.h>
-
-#define CONFIG_AT32AP
-#define CONFIG_AT32AP7000
-#define CONFIG_FAVR32_EZKIT
-
-#define CONFIG_FAVR32_EZKIT_EXT_FLASH
-
-/*
- * Set up the PLL to run at 140 MHz, the CPU to run at the PLL
- * frequency, the HSB and PBB at 1/2, and the PBA to run at 1/4 the
- * PLL frequency.
- * (CONFIG_SYS_OSC0_HZ * CONFIG_SYS_PLL0_MUL) / CONFIG_SYS_PLL0_DIV = PLL MHz
- */
-#define CONFIG_PLL
-#define CONFIG_SYS_POWER_MANAGER
-#define CONFIG_SYS_OSC0_HZ			20000000
-#define CONFIG_SYS_PLL0_DIV			1
-#define CONFIG_SYS_PLL0_MUL			7
-#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES	16
-/*
- * Set the CPU running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_CPU) = CPU MHz
- */
-#define CONFIG_SYS_CLKDIV_CPU			0
-/*
- * Set the HSB running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_HSB) = HSB MHz
- */
-#define CONFIG_SYS_CLKDIV_HSB			1
-/*
- * Set the PBA running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_PBA) = PBA MHz
- */
-#define CONFIG_SYS_CLKDIV_PBA			2
-/*
- * Set the PBB running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_PBB) = PBB MHz
- */
-#define CONFIG_SYS_CLKDIV_PBB			1
-
-/* Reserve VM regions for SDRAM and NOR flash */
-#define CONFIG_SYS_NR_VM_REGIONS		2
-
-/*
- * The PLLOPT register controls the PLL like this:
- *   icp = PLLOPT<2>
- *   ivco = PLLOPT<1:0>
- *
- * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz).
- */
-#define CONFIG_SYS_PLL0_OPT			0x04
-
-#define CONFIG_USART_BASE		ATMEL_BASE_USART3
-#define CONFIG_USART_ID			3
-
-/* User serviceable stuff */
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-#define CONFIG_STACKSIZE		(2048)
-
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_BOOTARGS							\
-	"root=/dev/mtdblock1 rootfstype=jffs fbmem=1800k"
-
-#define CONFIG_BOOTCOMMAND						\
-	"fsload; bootm $(fileaddr)"
-
-/*
- * Only interrupt autoboot if <space> is pressed. Otherwise, garbage
- * data on the serial line may interrupt the boot sequence.
- */
-#define CONFIG_BOOTDELAY		1
-#define CONFIG_AUTOBOOT
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT		\
-	"Press SPACE to abort autoboot in %d seconds\n", bootdelay
-#define CONFIG_AUTOBOOT_DELAY_STR	"d"
-#define CONFIG_AUTOBOOT_STOP_STR	" "
-
-/*
- * After booting the board for the first time, new ethernet addresses
- * should be generated and assigned to the environment variables
- * "ethaddr" and "eth1addr". This is normally done during production.
- */
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MMC
-
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_SETGETDCR
-#undef CONFIG_CMD_SOURCE
-#undef CONFIG_CMD_XIMG
-
-#define CONFIG_ATMEL_USART
-#define CONFIG_MACB
-#define CONFIG_PORTMUX_PIO
-#define CONFIG_SYS_NR_PIOS			5
-#define CONFIG_SYS_HSDRAMC
-#define CONFIG_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#define CONFIG_GENERIC_MMC
-
-#define CONFIG_SYS_DCACHE_LINESZ		32
-#define CONFIG_SYS_ICACHE_LINESZ		32
-
-#define CONFIG_NR_DRAM_BANKS		1
-
-/* External flash on Favr-32 */
-#if 0
-#define CONFIG_SYS_FLASH_CFI			1
-#define CONFIG_FLASH_CFI_DRIVER		1
-#endif
-
-#define CONFIG_SYS_FLASH_BASE			0x00000000
-#define CONFIG_SYS_FLASH_SIZE			0x800000
-#define CONFIG_SYS_MAX_FLASH_BANKS		1
-#define CONFIG_SYS_MAX_FLASH_SECT		135
-
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_TEXT_BASE		0x00000000
-
-#define CONFIG_SYS_INTRAM_BASE			INTERNAL_SRAM_BASE
-#define CONFIG_SYS_INTRAM_SIZE			INTERNAL_SRAM_SIZE
-#define CONFIG_SYS_SDRAM_BASE			EBI_SDRAM_BASE
-
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SIZE			65536
-#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE)
-
-#define CONFIG_SYS_MALLOC_LEN			(256*1024)
-
-/* Allow 4MB for the kernel run-time image */
-#define CONFIG_SYS_LOAD_ADDR			(EBI_SDRAM_BASE + 0x00400000)
-#define CONFIG_SYS_BOOTPARAMS_LEN		(16 * 1024)
-
-/* Other configuration settings that shouldn't have to change all that often */
-#define CONFIG_SYS_PROMPT			"U-Boot> "
-#define CONFIG_SYS_CBSIZE			256
-#define CONFIG_SYS_MAXARGS			16
-#define CONFIG_SYS_PBSIZE			(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-
-#define CONFIG_SYS_MEMTEST_START		EBI_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_END			(CONFIG_SYS_MEMTEST_START + 0x700000)
-#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 }
-
-#endif /* __CONFIG_H */
-- 
2.1.4

[U-Boot] [PATCH 3/7] avr32: delete non generic board hammerhead

[Andreas Bießmann]

Signed-off-by: Andreas Bie?mann <andreas.devel@googlemail.com>
---

 arch/avr32/Kconfig                     |   4 -
 board/miromico/hammerhead/Kconfig      |  15 ----
 board/miromico/hammerhead/MAINTAINERS  |   6 --
 board/miromico/hammerhead/Makefile     |   6 --
 board/miromico/hammerhead/hammerhead.c |  91 -------------------
 configs/hammerhead_defconfig           |   2 -
 include/configs/hammerhead.h           | 157 ---------------------------------
 7 files changed, 281 deletions(-)
 delete mode 100644 board/miromico/hammerhead/Kconfig
 delete mode 100644 board/miromico/hammerhead/MAINTAINERS
 delete mode 100644 board/miromico/hammerhead/Makefile
 delete mode 100644 board/miromico/hammerhead/hammerhead.c
 delete mode 100644 configs/hammerhead_defconfig
 delete mode 100644 include/configs/hammerhead.h

diff --git a/arch/avr32/Kconfig b/arch/avr32/Kconfig
index aa08d3e..8cc6cea 100644
--- a/arch/avr32/Kconfig
+++ b/arch/avr32/Kconfig
@@ -28,15 +28,11 @@ config TARGET_GRASSHOPPER
 config TARGET_MIMC200
 	bool "Support mimc200"
 
-config TARGET_HAMMERHEAD
-	bool "Support hammerhead"
-
 endchoice
 
 source "board/atmel/atngw100mkii/Kconfig"
 source "board/atmel/atstk1000/Kconfig"
 source "board/in-circuit/grasshopper/Kconfig"
 source "board/mimc/mimc200/Kconfig"
-source "board/miromico/hammerhead/Kconfig"
 
 endmenu
diff --git a/board/miromico/hammerhead/Kconfig b/board/miromico/hammerhead/Kconfig
deleted file mode 100644
index 1f09ef7..0000000
--- a/board/miromico/hammerhead/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_HAMMERHEAD
-
-config SYS_BOARD
-	default "hammerhead"
-
-config SYS_VENDOR
-	default "miromico"
-
-config SYS_SOC
-	default "at32ap700x"
-
-config SYS_CONFIG_NAME
-	default "hammerhead"
-
-endif
diff --git a/board/miromico/hammerhead/MAINTAINERS b/board/miromico/hammerhead/MAINTAINERS
deleted file mode 100644
index a87ceee..0000000
--- a/board/miromico/hammerhead/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-HAMMERHEAD BOARD
-M:	Alex Raimondi <alex.raimondi@miromico.ch>
-S:	Maintained
-F:	board/miromico/hammerhead/
-F:	include/configs/hammerhead.h
-F:	configs/hammerhead_defconfig
diff --git a/board/miromico/hammerhead/Makefile b/board/miromico/hammerhead/Makefile
deleted file mode 100644
index 638a9df..0000000
--- a/board/miromico/hammerhead/Makefile
+++ /dev/null
@@ -1,6 +0,0 @@
-#
-# Copyright (C) 2008 Miromico AG
-#
-# SPDX-License-Identifier:	GPL-2.0+
-
-obj-y	:= hammerhead.o
diff --git a/board/miromico/hammerhead/hammerhead.c b/board/miromico/hammerhead/hammerhead.c
deleted file mode 100644
index a0c7d3b..0000000
--- a/board/miromico/hammerhead/hammerhead.c
+++ /dev/null
@@ -1,91 +0,0 @@
-/*
- * Copyright (C) 2008 Miromico AG
- *
- * Mostly copied form atmel ATNGW100 sources
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-
-#include <asm/io.h>
-#include <asm/sdram.h>
-#include <asm/arch/clk.h>
-#include <asm/arch/hmatrix.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/mmu.h>
-#include <asm/arch/portmux.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = {
-	{
-		.virt_pgno	= CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT,
-		.nr_pages	= CONFIG_SYS_FLASH_SIZE >> MMU_PAGE_SHIFT,
-		.phys		= (CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT)
-					| MMU_VMR_CACHE_NONE,
-	}, {
-		.virt_pgno	= CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT,
-		.nr_pages	= EBI_SDRAM_SIZE >> MMU_PAGE_SHIFT,
-		.phys		= (CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT)
-					| MMU_VMR_CACHE_WRBACK,
-	},
-};
-
-static const struct sdram_config sdram_config = {
-	.data_bits	= SDRAM_DATA_32BIT,
-	.row_bits	= 13,
-	.col_bits	= 9,
-	.bank_bits	= 2,
-	.cas		= 3,
-	.twr		= 2,
-	.trc		= 7,
-	.trp		= 2,
-	.trcd		= 2,
-	.tras		= 5,
-	.txsr		= 5,
-	/* 7.81 us */
-	.refresh_period	= (781 * (SDRAMC_BUS_HZ / 1000)) / 100000,
-};
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
-	return macb_eth_initialize(0, (void *)ATMEL_BASE_MACB0,
-		bis->bi_phy_id[0]);
-}
-#endif
-
-int board_early_init_f(void)
-{
-	/* Enable SDRAM in the EBI mux */
-	hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE));
-
-	portmux_enable_ebi(32, 23, 0, PORTMUX_DRIVE_HIGH);
-	sdram_init(uncached(EBI_SDRAM_BASE), &sdram_config);
-
-	portmux_enable_usart1(PORTMUX_DRIVE_MIN);
-
-#if defined(CONFIG_MACB)
-	portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH);
-#endif
-#if defined(CONFIG_MMC)
-	portmux_enable_mmci(0, PORTMUX_MMCI_4BIT, PORTMUX_DRIVE_LOW);
-#endif
-	return 0;
-}
-
-int board_early_init_r(void)
-{
-	gd->bd->bi_phy_id[0] = 0x01;
-	return 0;
-}
-
-int board_postclk_init(void)
-{
-	/* Hammerhead boards uses GCLK3 as 25MHz output to ethernet PHY */
-	gclk_enable_output(3, PORTMUX_DRIVE_LOW);
-	gclk_set_rate(3, GCLK_PARENT_OSC0, 25000000);
-	return 0;
-}
diff --git a/configs/hammerhead_defconfig b/configs/hammerhead_defconfig
deleted file mode 100644
index 0d69cc6..0000000
--- a/configs/hammerhead_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_AVR32=y
-CONFIG_TARGET_HAMMERHEAD=y
diff --git a/include/configs/hammerhead.h b/include/configs/hammerhead.h
deleted file mode 100644
index 0bc42f1..0000000
--- a/include/configs/hammerhead.h
+++ /dev/null
@@ -1,157 +0,0 @@
-/*
- * Copyright (C) 2008 Miromico AG
- *
- * Configuration settings for the Miromico Hammerhead AVR32 board
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_AT32AP
-#define CONFIG_AT32AP7000
-#define CONFIG_HAMMERHEAD
-
-/*
- * Set up the PLL to run at 125 MHz, the CPU to run at the PLL
- * frequency, the HSB and PBB busses to run at 1/2 the PLL frequency
- * and the PBA bus to run at 1/4 the PLL frequency.
- */
-#define CONFIG_PLL
-#define CONFIG_SYS_POWER_MANAGER
-#define CONFIG_SYS_OSC0_HZ			25000000
-#define CONFIG_SYS_PLL0_DIV			1
-#define CONFIG_SYS_PLL0_MUL			5
-#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES	16
-#define CONFIG_SYS_CLKDIV_CPU			0
-#define CONFIG_SYS_CLKDIV_HSB			1
-#define CONFIG_SYS_CLKDIV_PBA			2
-#define CONFIG_SYS_CLKDIV_PBB			1
-
-/* Reserve VM regions for SDRAM and NOR flash */
-#define CONFIG_SYS_NR_VM_REGIONS		2
-
-/*
- * The PLLOPT register controls the PLL like this:
- *   icp = PLLOPT<2>
- *   ivco = PLLOPT<1:0>
- *
- * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz).
- */
-#define CONFIG_SYS_PLL0_OPT			0x04
-
-#define CONFIG_USART_BASE			ATMEL_BASE_USART1
-#define CONFIG_USART_ID				1
-
-#define CONFIG_HOSTNAME			hammerhead
-
-/* User serviceable stuff */
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-#define CONFIG_STACKSIZE		(2048)
-
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_BOOTARGS							\
-	"console=ttyS0 root=mtd1 rootfstype=jffs2"
-#define CONFIG_BOOTCOMMAND						\
-	"fsload; bootm"
-
-/*
- * Only interrupt autoboot if <space> is pressed. Otherwise, garbage
- * data on the serial line may interrupt the boot sequence.
- */
-#define CONFIG_BOOTDELAY		1
-#define CONFIG_AUTOBOOT
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT				\
-	"Press SPACE to abort autoboot in %d seconds\n", bootdelay
-#define CONFIG_AUTOBOOT_DELAY_STR	"d"
-#define CONFIG_AUTOBOOT_STOP_STR	" "
-
-/*
- * After booting the board for the first time, new ethernet address
- * should be generated and assigned to the environment variables
- * "ethaddr". This is normally done during production.
- */
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-
-/*
- * BOOTP/DHCP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MMC
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_SETGETDCR
-
-#define CONFIG_ATMEL_USART
-#define CONFIG_MACB
-#define CONFIG_PORTMUX_PIO
-#define CONFIG_SYS_NR_PIOS			5
-#define CONFIG_SYS_HSDRAMC
-#define CONFIG_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#define CONFIG_GENERIC_MMC
-
-#define CONFIG_SYS_DCACHE_LINESZ		32
-#define CONFIG_SYS_ICACHE_LINESZ		32
-
-#define CONFIG_NR_DRAM_BANKS		1
-
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-
-#define CONFIG_SYS_FLASH_BASE			0x00000000
-#define CONFIG_SYS_FLASH_SIZE			0x800000
-#define CONFIG_SYS_MAX_FLASH_BANKS		1
-#define CONFIG_SYS_MAX_FLASH_SECT		135
-
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_TEXT_BASE		0x00000000
-
-#define CONFIG_SYS_INTRAM_BASE			0x24000000
-#define CONFIG_SYS_INTRAM_SIZE			0x8000
-
-#define CONFIG_SYS_SDRAM_BASE			0x10000000
-
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SIZE			65536
-#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE)
-
-#define CONFIG_SYS_MALLOC_LEN			(256*1024)
-
-
-/* Allow 4MB for the kernel run-time image */
-#define CONFIG_SYS_LOAD_ADDR			(CONFIG_SYS_SDRAM_BASE + 0x00400000)
-#define CONFIG_SYS_BOOTPARAMS_LEN		(16 * 1024)
-
-/* Other configuration settings that shouldn't have to change all that often */
-#define CONFIG_SYS_PROMPT			"Hammerhead> "
-#define CONFIG_SYS_CBSIZE			256
-#define CONFIG_SYS_MAXARGS			16
-#define CONFIG_SYS_PBSIZE			(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-
-#define CONFIG_SYS_MEMTEST_START		CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_END			(CONFIG_SYS_MEMTEST_START + 0x1f00000)
-
-#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 }
-
-#endif /* __CONFIG_H */
-- 
2.1.4

[U-Boot] [PATCH 4/7] avr32: delete non generic board mimc200

[Andreas Bießmann]

Signed-off-by: Andreas Bie?mann <andreas.devel@googlemail.com>
---

 arch/avr32/Kconfig             |   4 -
 board/mimc/mimc200/Kconfig     |  15 ----
 board/mimc/mimc200/MAINTAINERS |   6 --
 board/mimc/mimc200/Makefile    |   6 --
 board/mimc/mimc200/mimc200.c   | 197 -----------------------------------------
 configs/mimc200_defconfig      |   2 -
 include/configs/mimc200.h      | 177 ------------------------------------
 7 files changed, 407 deletions(-)
 delete mode 100644 board/mimc/mimc200/Kconfig
 delete mode 100644 board/mimc/mimc200/MAINTAINERS
 delete mode 100644 board/mimc/mimc200/Makefile
 delete mode 100644 board/mimc/mimc200/mimc200.c
 delete mode 100644 configs/mimc200_defconfig
 delete mode 100644 include/configs/mimc200.h

diff --git a/arch/avr32/Kconfig b/arch/avr32/Kconfig
index 8cc6cea..c5c06ba 100644
--- a/arch/avr32/Kconfig
+++ b/arch/avr32/Kconfig
@@ -25,14 +25,10 @@ config TARGET_ATSTK1006
 config TARGET_GRASSHOPPER
 	bool "Support grasshopper"
 
-config TARGET_MIMC200
-	bool "Support mimc200"
-
 endchoice
 
 source "board/atmel/atngw100mkii/Kconfig"
 source "board/atmel/atstk1000/Kconfig"
 source "board/in-circuit/grasshopper/Kconfig"
-source "board/mimc/mimc200/Kconfig"
 
 endmenu
diff --git a/board/mimc/mimc200/Kconfig b/board/mimc/mimc200/Kconfig
deleted file mode 100644
index 18736d7..0000000
--- a/board/mimc/mimc200/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_MIMC200
-
-config SYS_BOARD
-	default "mimc200"
-
-config SYS_VENDOR
-	default "mimc"
-
-config SYS_SOC
-	default "at32ap700x"
-
-config SYS_CONFIG_NAME
-	default "mimc200"
-
-endif
diff --git a/board/mimc/mimc200/MAINTAINERS b/board/mimc/mimc200/MAINTAINERS
deleted file mode 100644
index 6cb51dd..0000000
--- a/board/mimc/mimc200/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-MIMC200 BOARD
-M:	Mark Jackson <mpfj@mimc.co.uk>
-S:	Maintained
-F:	board/mimc/mimc200/
-F:	include/configs/mimc200.h
-F:	configs/mimc200_defconfig
diff --git a/board/mimc/mimc200/Makefile b/board/mimc/mimc200/Makefile
deleted file mode 100644
index 5c30c0d..0000000
--- a/board/mimc/mimc200/Makefile
+++ /dev/null
@@ -1,6 +0,0 @@
-#
-# Copyright (C) 2005-2006 Atmel Corporation
-#
-# SPDX-License-Identifier:	GPL-2.0+
-
-obj-y	:= mimc200.o
diff --git a/board/mimc/mimc200/mimc200.c b/board/mimc/mimc200/mimc200.c
deleted file mode 100644
index f078295..0000000
--- a/board/mimc/mimc200/mimc200.c
+++ /dev/null
@@ -1,197 +0,0 @@
-/*
- * Copyright (C) 2006 Atmel Corporation
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-#include <common.h>
-#include <netdev.h>
-
-#include <asm/io.h>
-#include <asm/sdram.h>
-#include <asm/arch/clk.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/hmatrix.h>
-#include <asm/arch/mmu.h>
-#include <asm/arch/portmux.h>
-#include <atmel_lcdc.h>
-#include <lcd.h>
-
-#include "../../../arch/avr32/cpu/hsmc3.h"
-
-struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = {
-	{
-		.virt_pgno	= CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT,
-		.nr_pages	= CONFIG_SYS_FLASH_SIZE >> MMU_PAGE_SHIFT,
-		.phys		= (CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT)
-					| MMU_VMR_CACHE_NONE,
-	}, {
-		.virt_pgno	= EBI_SRAM_CS2_BASE >> MMU_PAGE_SHIFT,
-		.nr_pages	= EBI_SRAM_CS2_SIZE >> MMU_PAGE_SHIFT,
-		.phys		= (EBI_SRAM_CS2_BASE >> MMU_PAGE_SHIFT)
-					| MMU_VMR_CACHE_NONE,
-	}, {
-		.virt_pgno	= CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT,
-		.nr_pages	= EBI_SDRAM_SIZE >> MMU_PAGE_SHIFT,
-		.phys		= (CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT)
-					| MMU_VMR_CACHE_WRBACK,
-	},
-};
-
-#if defined(CONFIG_LCD)
-/* 480x272x16 @ 72 Hz */
-vidinfo_t panel_info = {
-	.vl_col			= 480,		/* Number of columns */
-	.vl_row			= 272,		/* Number of rows */
-	.vl_clk			= 5000000,	/* pixel clock in ps */
-	.vl_sync		= ATMEL_LCDC_INVCLK_INVERTED |
-				  ATMEL_LCDC_INVLINE_INVERTED |
-				  ATMEL_LCDC_INVFRAME_INVERTED,
-	.vl_bpix		= LCD_COLOR16,	/* Bits per pixel, BPP = 2^n */
-	.vl_tft			= 1,		/* 0 = passive, 1 = TFT */
-	.vl_hsync_len		= 42,		/* Length of horizontal sync */
-	.vl_left_margin		= 1,		/* Time from sync to picture */
-	.vl_right_margin	= 1,		/* Time from picture to sync */
-	.vl_vsync_len		= 1,		/* Length of vertical sync */
-	.vl_upper_margin	= 12,		/* Time from sync to picture */
-	.vl_lower_margin	= 1,		/* Time from picture to sync */
-	.mmio			= LCDC_BASE,	/* Memory mapped registers */
-};
-
-void lcd_enable(void)
-{
-}
-
-void lcd_disable(void)
-{
-}
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static const struct sdram_config sdram_config = {
-	.data_bits	= SDRAM_DATA_16BIT,
-	.row_bits	= 13,
-	.col_bits	= 9,
-	.bank_bits	= 2,
-	.cas		= 3,
-	.twr		= 2,
-	.trc		= 6,
-	.trp		= 2,
-	.trcd		= 2,
-	.tras		= 6,
-	.txsr		= 6,
-	/* 15.6 us */
-	.refresh_period	= (156 * (SDRAMC_BUS_HZ / 1000)) / 10000,
-};
-
-int board_early_init_f(void)
-{
-	/* Enable SDRAM in the EBI mux */
-	hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE));
-
-	/* Enable 26 address bits and NCS2 */
-	portmux_enable_ebi(16, 26, PORTMUX_EBI_CS(2), PORTMUX_DRIVE_HIGH);
-	sdram_init(uncached(EBI_SDRAM_BASE), &sdram_config);
-
-	portmux_enable_usart1(PORTMUX_DRIVE_MIN);
-
-	/* de-assert "force sys reset" pin */
-	portmux_select_gpio(PORTMUX_PORT_D, 1 << 15,
-			PORTMUX_DIR_OUTPUT | PORTMUX_INIT_HIGH);
-
-	/* init custom i/o */
-	/* cpu type inputs */
-	portmux_select_gpio(PORTMUX_PORT_E, (1 << 19) | (1 << 20) | (1 << 23),
-			PORTMUX_DIR_INPUT);
-	/* main board type inputs */
-	portmux_select_gpio(PORTMUX_PORT_B, (1 << 19) | (1 << 29),
-			PORTMUX_DIR_INPUT);
-	/* DEBUG input (use weak pullup) */
-	portmux_select_gpio(PORTMUX_PORT_E, 1 << 21,
-			PORTMUX_DIR_INPUT | PORTMUX_PULL_UP);
-
-	/* are we suppressing the console ? */
-	if (gpio_get_value(GPIO_PIN_PE(21)) == 1)
-		gd->flags |= (GD_FLG_SILENT | GD_FLG_DISABLE_CONSOLE);
-
-	/* reset phys */
-	portmux_select_gpio(PORTMUX_PORT_E, 1 << 24, PORTMUX_DIR_INPUT);
-	portmux_select_gpio(PORTMUX_PORT_C, 1 << 18,
-			PORTMUX_DIR_OUTPUT | PORTMUX_INIT_HIGH);
-
-	udelay(5000);
-
-	/* release phys reset */
-	gpio_set_value(GPIO_PIN_PC(18), 0);	/* PHY RESET (Release)	*/
-
-	/* setup Data Flash chip select (NCS2) */
-	hsmc3_writel(MODE2, 0x20121003);
-	hsmc3_writel(CYCLE2, 0x000a0009);
-	hsmc3_writel(PULSE2, 0x0a060806);
-	hsmc3_writel(SETUP2, 0x00030102);
-
-	/* setup FRAM chip select (NCS3) */
-	hsmc3_writel(MODE3, 0x10120001);
-	hsmc3_writel(CYCLE3, 0x001e001d);
-	hsmc3_writel(PULSE3, 0x08040704);
-	hsmc3_writel(SETUP3, 0x02050204);
-
-#if defined(CONFIG_MACB)
-	/* init macb0 pins */
-	portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH);
-	portmux_enable_macb1(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH);
-#endif
-
-#if defined(CONFIG_MMC)
-	portmux_enable_mmci(0, PORTMUX_MMCI_4BIT, PORTMUX_DRIVE_LOW);
-#endif
-
-#if defined(CONFIG_LCD)
-	portmux_enable_lcdc(1);
-#endif
-
-	return 0;
-}
-
-int board_early_init_r(void)
-{
-	gd->bd->bi_phy_id[0] = 0x01;
-	gd->bd->bi_phy_id[1] = 0x03;
-	return 0;
-}
-
-int board_postclk_init(void)
-{
-	/* Use GCLK0 as 10MHz output */
-	gclk_enable_output(0, PORTMUX_DRIVE_LOW);
-	gclk_set_rate(0, GCLK_PARENT_OSC0, 10000000);
-	return 0;
-}
-
-/* SPI chip select control */
-#ifdef CONFIG_ATMEL_SPI
-#include <spi.h>
-
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
-	return (bus == 0) && (cs == 0);
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
-}
-#endif /* CONFIG_ATMEL_SPI */
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bi)
-{
-	macb_eth_initialize(0, (void *)ATMEL_BASE_MACB0, bi->bi_phy_id[0]);
-	macb_eth_initialize(1, (void *)ATMEL_BASE_MACB1, bi->bi_phy_id[1]);
-
-	return 0;
-}
-#endif
diff --git a/configs/mimc200_defconfig b/configs/mimc200_defconfig
deleted file mode 100644
index f6edbc7..0000000
--- a/configs/mimc200_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_AVR32=y
-CONFIG_TARGET_MIMC200=y
diff --git a/include/configs/mimc200.h b/include/configs/mimc200.h
deleted file mode 100644
index 2fd3add..0000000
--- a/include/configs/mimc200.h
+++ /dev/null
@@ -1,177 +0,0 @@
-/*
- * Copyright (C) 2006 Atmel Corporation
- *
- * Configuration settings for the AVR32 Network Gateway
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/hardware.h>
-
-#define CONFIG_AT32AP
-#define CONFIG_AT32AP7000
-#define CONFIG_MIMC200
-
-#define CONFIG_MIMC200_EXT_FLASH
-
-/*
- * Set up the PLL to run at 140 MHz, the CPU to run at the PLL
- * frequency, the HSB and PBB busses to run at 1/2 the PLL frequency
- * and the PBA bus to run at 1/4 the PLL frequency.
- */
-#define CONFIG_PLL
-#define CONFIG_SYS_POWER_MANAGER
-#define CONFIG_SYS_OSC0_HZ			10000000
-#define CONFIG_SYS_PLL0_DIV			1
-#define CONFIG_SYS_PLL0_MUL			15
-#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES	16
-#define CONFIG_SYS_CLKDIV_CPU			0
-#define CONFIG_SYS_CLKDIV_HSB			1
-#define CONFIG_SYS_CLKDIV_PBA			2
-#define CONFIG_SYS_CLKDIV_PBB			1
-
-/* Reserve VM regions for SDRAM, NOR flash and FRAM */
-#define CONFIG_SYS_NR_VM_REGIONS		3
-
-/*
- * The PLLOPT register controls the PLL like this:
- *   icp = PLLOPT<2>
- *   ivco = PLLOPT<1:0>
- *
- * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz).
- */
-#define CONFIG_SYS_PLL0_OPT			0x04
-
-#define CONFIG_USART_BASE			ATMEL_BASE_USART1
-#define CONFIG_USART_ID				1
-
-#define CONFIG_MIMC200_DBGLINK		1
-
-/* User serviceable stuff */
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-#define CONFIG_STACKSIZE		(2048)
-
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_BOOTARGS							\
-	"root=/dev/mtdblock1 rootfstype=jffs2 fbmem=512k console=ttyS1"
-#define CONFIG_BOOTCOMMAND						\
-	"fsload boot/uImage; bootm"
-
-#define CONFIG_SILENT_CONSOLE       /* enable silent startup */
-#define CONFIG_DISABLE_CONSOLE      /* disable console */
-#define CONFIG_SYS_DEVICE_NULLDEV   /* include nulldev device */
-
-#define CONFIG_LCD			1
-
-/*
- * Only interrupt autoboot if <space> is pressed. Otherwise, garbage
- * data on the serial line may interrupt the boot sequence.
- */
-#define CONFIG_BOOTDELAY		0
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-#define CONFIG_AUTOBOOT
-
-/*
- * After booting the board for the first time, new ethernet addresses
- * should be generated and assigned to the environment variables
- * "ethaddr" and "eth1addr". This is normally done during production.
- */
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-
-/*
- * BOOTP/DHCP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MMC
-#define CONFIG_CMD_NET
-
-#define CONFIG_ATMEL_USART
-#define CONFIG_MACB
-#define CONFIG_PORTMUX_PIO
-#define CONFIG_SYS_NR_PIOS			5
-#define CONFIG_SYS_HSDRAMC
-#define CONFIG_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#define CONFIG_GENERIC_MMC
-
-#if defined(CONFIG_LCD)
-#define CONFIG_CMD_BMP
-#define CONFIG_ATMEL_LCD		1
-#define LCD_BPP				LCD_COLOR16
-#define CONFIG_BMP_16BPP		1
-#define CONFIG_FB_ADDR			0x10600000
-#define CONFIG_WHITE_ON_BLACK		1
-#define CONFIG_VIDEO_BMP_GZIP 		1
-#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE		262144
-#define CONFIG_ATMEL_LCD_BGR555		1
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
-#define CONFIG_SPLASH_SCREEN		1
-#endif
-
-#define CONFIG_SYS_DCACHE_LINESZ		32
-#define CONFIG_SYS_ICACHE_LINESZ		32
-
-#define CONFIG_NR_DRAM_BANKS		1
-
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-
-#define CONFIG_SYS_FLASH_BASE			0x00000000
-#define CONFIG_SYS_FLASH_SIZE			0x800000
-#define CONFIG_SYS_MAX_FLASH_BANKS		1
-#define CONFIG_SYS_MAX_FLASH_SECT		135
-
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_TEXT_BASE		0x00000000
-
-#define CONFIG_SYS_INTRAM_BASE			INTERNAL_SRAM_BASE
-#define CONFIG_SYS_INTRAM_SIZE			INTERNAL_SRAM_SIZE
-#define CONFIG_SYS_SDRAM_BASE			EBI_SDRAM_BASE
-
-#define CONFIG_SYS_FRAM_BASE			0x08000000
-#define CONFIG_SYS_FRAM_SIZE			0x20000
-
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SIZE			65536
-#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE)
-
-#define CONFIG_SYS_MALLOC_LEN			(1024*1024)
-
-/* Allow 4MB for the kernel run-time image */
-#define CONFIG_SYS_LOAD_ADDR			(EBI_SDRAM_BASE + 0x00400000)
-#define CONFIG_SYS_BOOTPARAMS_LEN		(16 * 1024)
-
-/* Other configuration settings that shouldn't have to change all that often */
-#define CONFIG_SYS_PROMPT			"U-Boot> "
-#define CONFIG_SYS_CBSIZE			256
-#define CONFIG_SYS_MAXARGS			16
-#define CONFIG_SYS_PBSIZE			(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-
-#define CONFIG_SYS_MEMTEST_START		EBI_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_END			(CONFIG_SYS_MEMTEST_START + 0x1f00000)
-
-#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 }
-
-#endif /* __CONFIG_H */
-- 
2.1.4

[U-Boot] [PATCH 5/7] avr32: delete non generic board's atstk100{3, 4, 6}

[Andreas Bießmann]

Signed-off-by: Andreas Bie?mann <andreas.devel@googlemail.com>
---

 arch/avr32/Kconfig                |   9 --
 board/atmel/atstk1000/Kconfig     |  48 ----------
 board/atmel/atstk1000/MAINTAINERS |   6 --
 board/atmel/atstk1000/atstk1000.c |  23 +----
 configs/atstk1003_defconfig       |   2 -
 configs/atstk1004_defconfig       |   2 -
 configs/atstk1006_defconfig       |   2 -
 include/configs/atstk1003.h       | 161 ----------------------------------
 include/configs/atstk1004.h       | 161 ----------------------------------
 include/configs/atstk1006.h       | 178 --------------------------------------
 10 files changed, 1 insertion(+), 591 deletions(-)
 delete mode 100644 configs/atstk1003_defconfig
 delete mode 100644 configs/atstk1004_defconfig
 delete mode 100644 configs/atstk1006_defconfig
 delete mode 100644 include/configs/atstk1003.h
 delete mode 100644 include/configs/atstk1004.h
 delete mode 100644 include/configs/atstk1006.h

diff --git a/arch/avr32/Kconfig b/arch/avr32/Kconfig
index c5c06ba..2228dc1 100644
--- a/arch/avr32/Kconfig
+++ b/arch/avr32/Kconfig
@@ -13,15 +13,6 @@ config TARGET_ATNGW100MKII
 config TARGET_ATSTK1002
 	bool "Support atstk1002"
 
-config TARGET_ATSTK1003
-	bool "Support atstk1003"
-
-config TARGET_ATSTK1004
-	bool "Support atstk1004"
-
-config TARGET_ATSTK1006
-	bool "Support atstk1006"
-
 config TARGET_GRASSHOPPER
 	bool "Support grasshopper"
 
diff --git a/board/atmel/atstk1000/Kconfig b/board/atmel/atstk1000/Kconfig
index 6d41514..b4fa9a2 100644
--- a/board/atmel/atstk1000/Kconfig
+++ b/board/atmel/atstk1000/Kconfig
@@ -13,51 +13,3 @@ config SYS_CONFIG_NAME
 	default "atstk1002"
 
 endif
-
-if TARGET_ATSTK1003
-
-config SYS_BOARD
-	default "atstk1000"
-
-config SYS_VENDOR
-	default "atmel"
-
-config SYS_SOC
-	default "at32ap700x"
-
-config SYS_CONFIG_NAME
-	default "atstk1003"
-
-endif
-
-if TARGET_ATSTK1004
-
-config SYS_BOARD
-	default "atstk1000"
-
-config SYS_VENDOR
-	default "atmel"
-
-config SYS_SOC
-	default "at32ap700x"
-
-config SYS_CONFIG_NAME
-	default "atstk1004"
-
-endif
-
-if TARGET_ATSTK1006
-
-config SYS_BOARD
-	default "atstk1000"
-
-config SYS_VENDOR
-	default "atmel"
-
-config SYS_SOC
-	default "at32ap700x"
-
-config SYS_CONFIG_NAME
-	default "atstk1006"
-
-endif
diff --git a/board/atmel/atstk1000/MAINTAINERS b/board/atmel/atstk1000/MAINTAINERS
index 378e1b3..6143846 100644
--- a/board/atmel/atstk1000/MAINTAINERS
+++ b/board/atmel/atstk1000/MAINTAINERS
@@ -4,9 +4,3 @@ S:	Orphan (since 2014-06)
 F:	board/atmel/atstk1000/
 F:	include/configs/atstk1002.h
 F:	configs/atstk1002_defconfig
-F:	include/configs/atstk1003.h
-F:	configs/atstk1003_defconfig
-F:	include/configs/atstk1004.h
-F:	configs/atstk1004_defconfig
-F:	include/configs/atstk1006.h
-F:	configs/atstk1006_defconfig
diff --git a/board/atmel/atstk1000/atstk1000.c b/board/atmel/atstk1000/atstk1000.c
index fd4363b..679b674 100644
--- a/board/atmel/atstk1000/atstk1000.c
+++ b/board/atmel/atstk1000/atstk1000.c
@@ -30,32 +30,12 @@ struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = {
 };
 
 static const struct sdram_config sdram_config = {
-#if defined(CONFIG_ATSTK1006)
-	/* Dual MT48LC16M16A2-7E (64 MB) on daughterboard */
 	.data_bits	= SDRAM_DATA_32BIT,
-	.row_bits	= 13,
-	.col_bits	= 9,
-	.bank_bits	= 2,
-	.cas		= 2,
-	.twr		= 2,
-	.trc		= 7,
-	.trp		= 2,
-	.trcd		= 2,
-	.tras		= 4,
-	.txsr		= 7,
-	/* 7.81 us */
-	.refresh_period	= (781 * (SDRAMC_BUS_HZ / 1000)) / 100000,
-#else
-	/* MT48LC2M32B2P-5 (8 MB) on motherboard */
-#ifdef CONFIG_ATSTK1004
-	.data_bits	= SDRAM_DATA_16BIT,
-#else
-	.data_bits	= SDRAM_DATA_32BIT,
-#endif
 #ifdef CONFIG_ATSTK1000_16MB_SDRAM
 	/* MT48LC4M32B2P-6 (16 MB) on mod'ed motherboard */
 	.row_bits	= 12,
 #else
+	/* MT48LC2M32B2P-5 (8 MB) on motherboard */
 	.row_bits	= 11,
 #endif
 	.col_bits	= 8,
@@ -69,7 +49,6 @@ static const struct sdram_config sdram_config = {
 	.txsr		= 5,
 	/* 15.6 us */
 	.refresh_period	= (156 * (SDRAMC_BUS_HZ / 1000)) / 10000,
-#endif
 };
 
 int board_early_init_f(void)
diff --git a/configs/atstk1003_defconfig b/configs/atstk1003_defconfig
deleted file mode 100644
index b704532..0000000
--- a/configs/atstk1003_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_AVR32=y
-CONFIG_TARGET_ATSTK1003=y
diff --git a/configs/atstk1004_defconfig b/configs/atstk1004_defconfig
deleted file mode 100644
index 7650254..0000000
--- a/configs/atstk1004_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_AVR32=y
-CONFIG_TARGET_ATSTK1004=y
diff --git a/configs/atstk1006_defconfig b/configs/atstk1006_defconfig
deleted file mode 100644
index 54beb0b..0000000
--- a/configs/atstk1006_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_AVR32=y
-CONFIG_TARGET_ATSTK1006=y
diff --git a/include/configs/atstk1003.h b/include/configs/atstk1003.h
deleted file mode 100644
index 63704b1..0000000
--- a/include/configs/atstk1003.h
+++ /dev/null
@@ -1,161 +0,0 @@
-/*
- * Copyright (C) 2007 Atmel Corporation
- *
- * Configuration settings for the ATSTK1003 CPU daughterboard
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/hardware.h>
-
-#define CONFIG_AT32AP
-#define CONFIG_AT32AP7001
-#define CONFIG_ATSTK1003
-#define CONFIG_ATSTK1000
-
-/*
- * Set up the PLL to run at 140 MHz, the CPU to run at the PLL
- * frequency, the HSB and PBB at 1/2, and the PBA to run at 1/4 the
- * PLL frequency.
- * (CONFIG_SYS_OSC0_HZ * CONFIG_SYS_PLL0_MUL) / CONFIG_SYS_PLL0_DIV = PLL MHz
- */
-#define CONFIG_PLL
-#define CONFIG_SYS_POWER_MANAGER
-#define CONFIG_SYS_OSC0_HZ			20000000
-#define CONFIG_SYS_PLL0_DIV			1
-#define CONFIG_SYS_PLL0_MUL			7
-#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES	16
-/*
- * Set the CPU running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_CPU) = CPU MHz
- */
-#define CONFIG_SYS_CLKDIV_CPU			0
-/*
- * Set the HSB running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_HSB) = HSB MHz
- */
-#define CONFIG_SYS_CLKDIV_HSB			1
-/*
- * Set the PBA running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_PBA) = PBA MHz
- */
-#define CONFIG_SYS_CLKDIV_PBA			2
-/*
- * Set the PBB running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_PBB) = PBB MHz
- */
-#define CONFIG_SYS_CLKDIV_PBB			1
-
-/* Reserve VM regions for SDRAM and NOR flash */
-#define CONFIG_SYS_NR_VM_REGIONS		2
-
-/*
- * The PLLOPT register controls the PLL like this:
- *   icp = PLLOPT<2>
- *   ivco = PLLOPT<1:0>
- *
- * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz).
- */
-#define CONFIG_SYS_PLL0_OPT			0x04
-
-#define CONFIG_USART_BASE		ATMEL_BASE_USART1
-#define CONFIG_USART_ID			1
-
-/* User serviceable stuff */
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-#define CONFIG_STACKSIZE		(2048)
-
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_BOOTARGS							\
-	"console=ttyS0 root=/dev/mmcblk0p1 rootwait"
-
-#define CONFIG_BOOTCOMMAND						\
-	"mmc rescan; ext2load mmc 0:1 0x10400000 /boot/uImage; bootm"
-
-/*
- * Only interrupt autoboot if <space> is pressed. Otherwise, garbage
- * data on the serial line may interrupt the boot sequence.
- */
-#define CONFIG_BOOTDELAY		1
-#define CONFIG_AUTOBOOT
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT		\
-	"Press SPACE to abort autoboot in %d seconds\n", bootdelay
-#define CONFIG_AUTOBOOT_DELAY_STR	"d"
-#define CONFIG_AUTOBOOT_STOP_STR	" "
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MMC
-
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
-#undef CONFIG_CMD_SETGETDCR
-#undef CONFIG_CMD_XIMG
-
-#define CONFIG_ATMEL_USART
-#define CONFIG_PORTMUX_PIO
-#define CONFIG_SYS_HSDRAMC
-#define CONFIG_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#define CONFIG_GENERIC_MMC
-
-#define CONFIG_SYS_DCACHE_LINESZ		32
-#define CONFIG_SYS_ICACHE_LINESZ		32
-
-#define CONFIG_NR_DRAM_BANKS		1
-
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-
-#define CONFIG_SYS_FLASH_BASE			0x00000000
-#define CONFIG_SYS_FLASH_SIZE			0x800000
-#define CONFIG_SYS_MAX_FLASH_BANKS		1
-#define CONFIG_SYS_MAX_FLASH_SECT		135
-
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_TEXT_BASE		0x00000000
-
-#define CONFIG_SYS_INTRAM_BASE			INTERNAL_SRAM_BASE
-#define CONFIG_SYS_INTRAM_SIZE			INTERNAL_SRAM_SIZE
-#define CONFIG_SYS_SDRAM_BASE			EBI_SDRAM_BASE
-
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SIZE			65536
-#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE)
-
-#define CONFIG_SYS_MALLOC_LEN			(256*1024)
-
-/* Allow 4MB for the kernel run-time image */
-#define CONFIG_SYS_LOAD_ADDR			(EBI_SDRAM_BASE + 0x00400000)
-#define CONFIG_SYS_BOOTPARAMS_LEN		(16 * 1024)
-
-/* Other configuration settings that shouldn't have to change all that often */
-#define CONFIG_SYS_PROMPT			"U-Boot> "
-#define CONFIG_SYS_CBSIZE			256
-#define CONFIG_SYS_MAXARGS			16
-#define CONFIG_SYS_PBSIZE			(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-
-#define CONFIG_SYS_MEMTEST_START		EBI_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_END			(CONFIG_SYS_MEMTEST_START + 0x700000)
-#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 }
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/atstk1004.h b/include/configs/atstk1004.h
deleted file mode 100644
index 331a60d..0000000
--- a/include/configs/atstk1004.h
+++ /dev/null
@@ -1,161 +0,0 @@
-/*
- * Copyright (C) 2007 Atmel Corporation
- *
- * Configuration settings for the ATSTK1003 CPU daughterboard
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/hardware.h>
-
-#define CONFIG_AT32AP
-#define CONFIG_AT32AP7002
-#define CONFIG_ATSTK1004
-#define CONFIG_ATSTK1000
-
-/*
- * Set up the PLL to run at 140 MHz, the CPU to run at the PLL
- * frequency, the HSB and PBB at 1/2, and the PBA to run at 1/4 the
- * PLL frequency.
- * (CONFIG_SYS_OSC0_HZ * CONFIG_SYS_PLL0_MUL) / CONFIG_SYS_PLL0_DIV = PLL MHz
- */
-#define CONFIG_PLL
-#define CONFIG_SYS_POWER_MANAGER
-#define CONFIG_SYS_OSC0_HZ			20000000
-#define CONFIG_SYS_PLL0_DIV			1
-#define CONFIG_SYS_PLL0_MUL			7
-#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES	16
-/*
- * Set the CPU running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_CPU) = CPU MHz
- */
-#define CONFIG_SYS_CLKDIV_CPU			0
-/*
- * Set the HSB running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_HSB) = HSB MHz
- */
-#define CONFIG_SYS_CLKDIV_HSB			1
-/*
- * Set the PBA running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_PBA) = PBA MHz
- */
-#define CONFIG_SYS_CLKDIV_PBA			2
-/*
- * Set the PBB running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_PBB) = PBB MHz
- */
-#define CONFIG_SYS_CLKDIV_PBB			1
-
-/* Reserve VM regions for SDRAM and NOR flash */
-#define CONFIG_SYS_NR_VM_REGIONS		2
-
-/*
- * The PLLOPT register controls the PLL like this:
- *   icp = PLLOPT<2>
- *   ivco = PLLOPT<1:0>
- *
- * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz).
- */
-#define CONFIG_SYS_PLL0_OPT			0x04
-
-#define CONFIG_USART_BASE		ATMEL_BASE_USART1
-#define CONFIG_USART_ID			1
-
-/* User serviceable stuff */
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-#define CONFIG_STACKSIZE		(2048)
-
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_BOOTARGS							\
-	"console=ttyS0 root=/dev/mmcblk0p1 rootwait"
-
-#define CONFIG_BOOTCOMMAND						\
-	"mmc rescan; ext2load mmc 0:1 0x10200000 /boot/uImage; bootm"
-
-/*
- * Only interrupt autoboot if <space> is pressed. Otherwise, garbage
- * data on the serial line may interrupt the boot sequence.
- */
-#define CONFIG_BOOTDELAY		1
-#define CONFIG_AUTOBOOT
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT		\
-	"Press SPACE to abort autoboot in %d seconds\n", bootdelay
-#define CONFIG_AUTOBOOT_DELAY_STR	"d"
-#define CONFIG_AUTOBOOT_STOP_STR	" "
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MMC
-
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
-#undef CONFIG_CMD_SETGETDCR
-#undef CONFIG_CMD_XIMG
-
-#define CONFIG_ATMEL_USART
-#define CONFIG_PORTMUX_PIO
-#define CONFIG_SYS_HSDRAMC
-#define CONFIG_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#define CONFIG_GENERIC_MMC
-
-#define CONFIG_SYS_DCACHE_LINESZ		32
-#define CONFIG_SYS_ICACHE_LINESZ		32
-
-#define CONFIG_NR_DRAM_BANKS		1
-
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-
-#define CONFIG_SYS_FLASH_BASE			0x00000000
-#define CONFIG_SYS_FLASH_SIZE			0x800000
-#define CONFIG_SYS_MAX_FLASH_BANKS		1
-#define CONFIG_SYS_MAX_FLASH_SECT		135
-
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_TEXT_BASE		0x00000000
-
-#define CONFIG_SYS_INTRAM_BASE			INTERNAL_SRAM_BASE
-#define CONFIG_SYS_INTRAM_SIZE			INTERNAL_SRAM_SIZE
-#define CONFIG_SYS_SDRAM_BASE			EBI_SDRAM_BASE
-
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SIZE			65536
-#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE)
-
-#define CONFIG_SYS_MALLOC_LEN			(256*1024)
-
-/* Allow 2MB for the kernel run-time image */
-#define CONFIG_SYS_LOAD_ADDR			(EBI_SDRAM_BASE + 0x00200000)
-#define CONFIG_SYS_BOOTPARAMS_LEN		(16 * 1024)
-
-/* Other configuration settings that shouldn't have to change all that often */
-#define CONFIG_SYS_PROMPT			"U-Boot> "
-#define CONFIG_SYS_CBSIZE			256
-#define CONFIG_SYS_MAXARGS			16
-#define CONFIG_SYS_PBSIZE			(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-
-#define CONFIG_SYS_MEMTEST_START		EBI_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_END			(CONFIG_SYS_MEMTEST_START + 0x700000)
-#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 }
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/atstk1006.h b/include/configs/atstk1006.h
deleted file mode 100644
index 25090a6..0000000
--- a/include/configs/atstk1006.h
+++ /dev/null
@@ -1,178 +0,0 @@
-/*
- * Copyright (C) 2005-2006 Atmel Corporation
- *
- * Configuration settings for the ATSTK1002 CPU daughterboard
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/hardware.h>
-
-#define CONFIG_AT32AP
-#define CONFIG_AT32AP7000
-#define CONFIG_ATSTK1006
-#define CONFIG_ATSTK1000
-
-
-/*
- * Set up the PLL to run at 140 MHz, the CPU to run at the PLL
- * frequency, the HSB and PBB at 1/2, and the PBA to run at 1/4 the
- * PLL frequency.
- * (CONFIG_SYS_OSC0_HZ * CONFIG_SYS_PLL0_MUL) / CONFIG_SYS_PLL0_DIV = PLL MHz
- */
-#define CONFIG_PLL
-#define CONFIG_SYS_POWER_MANAGER
-#define CONFIG_SYS_OSC0_HZ			20000000
-#define CONFIG_SYS_PLL0_DIV			1
-#define CONFIG_SYS_PLL0_MUL			7
-#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES	16
-/*
- * Set the CPU running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_CPU) = CPU MHz
- */
-#define CONFIG_SYS_CLKDIV_CPU			0
-/*
- * Set the HSB running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_HSB) = HSB MHz
- */
-#define CONFIG_SYS_CLKDIV_HSB			1
-/*
- * Set the PBA running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_PBA) = PBA MHz
- */
-#define CONFIG_SYS_CLKDIV_PBA			2
-/*
- * Set the PBB running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_PBB) = PBB MHz
- */
-#define CONFIG_SYS_CLKDIV_PBB			1
-
-/* Reserve VM regions for SDRAM and NOR flash */
-#define CONFIG_SYS_NR_VM_REGIONS		2
-
-/*
- * The PLLOPT register controls the PLL like this:
- *   icp = PLLOPT<2>
- *   ivco = PLLOPT<1:0>
- *
- * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz).
- */
-#define CONFIG_SYS_PLL0_OPT			0x04
-
-#define CONFIG_USART_BASE		ATMEL_BASE_USART1
-#define CONFIG_USART_ID			1
-
-/* User serviceable stuff */
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-#define CONFIG_STACKSIZE		(2048)
-
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_BOOTARGS							\
-	"console=ttyS0 root=mtd3 fbmem=2400k"
-
-#define CONFIG_BOOTCOMMAND						\
-	"fsload; bootm $(fileaddr)"
-
-/*
- * Only interrupt autoboot if <space> is pressed. Otherwise, garbage
- * data on the serial line may interrupt the boot sequence.
- */
-#define CONFIG_BOOTDELAY		1
-#define CONFIG_AUTOBOOT
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT		\
-	"Press SPACE to abort autoboot in %d seconds\n", bootdelay
-#define CONFIG_AUTOBOOT_DELAY_STR	"d"
-#define CONFIG_AUTOBOOT_STOP_STR	" "
-
-/*
- * After booting the board for the first time, new ethernet addresses
- * should be generated and assigned to the environment variables
- * "ethaddr" and "eth1addr". This is normally done during production.
- */
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MMC
-
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_SETGETDCR
-#undef CONFIG_CMD_SOURCE
-#undef CONFIG_CMD_XIMG
-
-#define CONFIG_ATMEL_USART
-#define CONFIG_MACB
-#define CONFIG_PORTMUX_PIO
-#define CONFIG_SYS_NR_PIOS			5
-#define CONFIG_SYS_HSDRAMC
-#define CONFIG_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#define CONFIG_GENERIC_MMC
-
-#define CONFIG_SYS_DCACHE_LINESZ		32
-#define CONFIG_SYS_ICACHE_LINESZ		32
-
-#define CONFIG_NR_DRAM_BANKS		1
-
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-
-#define CONFIG_SYS_FLASH_BASE			0x00000000
-#define CONFIG_SYS_FLASH_SIZE			0x800000
-#define CONFIG_SYS_MAX_FLASH_BANKS		1
-#define CONFIG_SYS_MAX_FLASH_SECT		135
-
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_TEXT_BASE		0x00000000
-
-#define CONFIG_SYS_INTRAM_BASE			INTERNAL_SRAM_BASE
-#define CONFIG_SYS_INTRAM_SIZE			INTERNAL_SRAM_SIZE
-#define CONFIG_SYS_SDRAM_BASE			EBI_SDRAM_BASE
-
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SIZE			65536
-#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE)
-
-#define CONFIG_SYS_MALLOC_LEN			(256*1024)
-
-/* Allow 4MB for the kernel run-time image */
-#define CONFIG_SYS_LOAD_ADDR			(EBI_SDRAM_BASE + 0x00400000)
-#define CONFIG_SYS_BOOTPARAMS_LEN		(16 * 1024)
-
-/* Other configuration settings that shouldn't have to change all that often */
-#define CONFIG_SYS_PROMPT			"U-Boot> "
-#define CONFIG_SYS_CBSIZE			256
-#define CONFIG_SYS_MAXARGS			16
-#define CONFIG_SYS_PBSIZE			(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-
-#define CONFIG_SYS_MEMTEST_START		EBI_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_END			(CONFIG_SYS_MEMTEST_START + 0x3f00000)
-#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 }
-
-#endif /* __CONFIG_H */
-- 
2.1.4

[U-Boot] [PATCH 6/7] avr32: take maintainership for atstk1002

[Andreas Bießmann]

I have this board at work, so I can trun tests on it.

Signed-off-by: Andreas Bie?mann <andreas.devel@googlemail.com>
---

 board/atmel/atstk1000/MAINTAINERS | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/board/atmel/atstk1000/MAINTAINERS b/board/atmel/atstk1000/MAINTAINERS
index 6143846..1070f98 100644
--- a/board/atmel/atstk1000/MAINTAINERS
+++ b/board/atmel/atstk1000/MAINTAINERS
@@ -1,6 +1,6 @@
 ATSTK1000 BOARD
-#M:	Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
-S:	Orphan (since 2014-06)
+M:	Andreas Bie?mann <andreas.biessmann@corscience.de>
+S:	Maintained
 F:	board/atmel/atstk1000/
 F:	include/configs/atstk1002.h
 F:	configs/atstk1002_defconfig
-- 
2.1.4

[U-Boot] [PATCH 7/7] avr32: delete ancient board.c

[Andreas Bießmann]

Signed-off-by: Andreas Bie?mann <andreas.devel@googlemail.com>
---

 arch/avr32/lib/Makefile |   3 -
 arch/avr32/lib/board.c  | 256 ------------------------------------------------
 2 files changed, 259 deletions(-)
 delete mode 100644 arch/avr32/lib/board.c

diff --git a/arch/avr32/lib/Makefile b/arch/avr32/lib/Makefile
index 6750913..8108ae5 100644
--- a/arch/avr32/lib/Makefile
+++ b/arch/avr32/lib/Makefile
@@ -8,9 +8,6 @@
 #
 
 obj-y	+= memset.o
-ifndef CONFIG_SYS_GENERIC_BOARD
-obj-y	+= board.o
-endif
 obj-$(CONFIG_CMD_BOOTM) += bootm.o
 obj-y	+= interrupts.o
 obj-y	+= dram_init.o
diff --git a/arch/avr32/lib/board.c b/arch/avr32/lib/board.c
deleted file mode 100644
index aacfcbf..0000000
--- a/arch/avr32/lib/board.c
+++ /dev/null
@@ -1,256 +0,0 @@
-/*
- * Copyright (C) 2004-2006 Atmel Corporation
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-#include <common.h>
-#include <command.h>
-#include <malloc.h>
-#include <stdio_dev.h>
-#include <version.h>
-#include <net.h>
-
-#ifdef CONFIG_BITBANGMII
-#include <miiphy.h>
-#endif
-
-#include <asm/sections.h>
-#include <asm/arch/mmu.h>
-#include <asm/arch/hardware.h>
-
-#ifndef CONFIG_IDENT_STRING
-#define CONFIG_IDENT_STRING ""
-#endif
-
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-#include <mmc.h>
-#endif
-DECLARE_GLOBAL_DATA_PTR;
-
-unsigned long monitor_flash_len;
-
-__weak void dram_init_banksize(void)
-{
-	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
-	gd->bd->bi_dram[0].size =  gd->ram_size;
-}
-
-/* Weak aliases for optional board functions */
-static int __do_nothing(void)
-{
-	return 0;
-}
-int board_postclk_init(void) __attribute__((weak, alias("__do_nothing")));
-int board_early_init_r(void) __attribute__((weak, alias("__do_nothing")));
-
-static int init_baudrate(void)
-{
-	gd->baudrate = getenv_ulong("baudrate", 10, CONFIG_BAUDRATE);
-	return 0;
-}
-
-static int display_banner (void)
-{
-	printf ("\n\n%s\n\n", version_string);
-	printf ("U-Boot code: %08lx -> %08lx  data: %08lx -> %08lx\n",
-		(unsigned long)_text, (unsigned long)_etext,
-		(unsigned long)_data, (unsigned long)(&__bss_end));
-	return 0;
-}
-
-static int display_dram_config (void)
-{
-	int i;
-
-	puts ("DRAM Configuration:\n");
-
-	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
-		printf ("Bank #%d: %08lx ", i, gd->bd->bi_dram[i].start);
-		print_size (gd->bd->bi_dram[i].size, "\n");
-	}
-
-	return 0;
-}
-
-static void display_flash_config (void)
-{
-	puts ("Flash: ");
-	print_size(gd->bd->bi_flashsize, " ");
-	printf("at address 0x%08lx\n", gd->bd->bi_flashstart);
-}
-
-void board_init_f(ulong board_type)
-{
-	gd_t gd_data;
-	gd_t *new_gd;
-	bd_t *bd;
-	unsigned long *new_sp;
-	unsigned long monitor_len;
-	unsigned long monitor_addr;
-	unsigned long addr;
-
-	/* Initialize the global data pointer */
-	memset(&gd_data, 0, sizeof(gd_data));
-	gd = &gd_data;
-
-	/* Perform initialization sequence */
-	board_early_init_f();
-	arch_cpu_init();
-	board_postclk_init();
-	env_init();
-	init_baudrate();
-	serial_init();
-	console_init_f();
-	display_banner();
-	dram_init();
-
-	/* If we have no SDRAM, we can't go on */
-	if (gd->ram_size <= 0)
-		panic("No working SDRAM available\n");
-
-	/*
-	 * Now that we have DRAM mapped and working, we can
-	 * relocate the code and continue running from DRAM.
-	 *
-	 * Reserve memory@end of RAM for (top down in that order):
-	 *  - u-boot image
-	 *  - heap for malloc()
-	 *  - board info struct
-	 *  - global data struct
-	 *  - stack
-	 */
-	addr = CONFIG_SYS_SDRAM_BASE + gd->ram_size;
-	monitor_len = (char *)(&__bss_end) - _text;
-
-	/*
-	 * Reserve memory for u-boot code, data and bss.
-	 * Round down to next 4 kB limit.
-	 */
-	addr -= monitor_len;
-	addr &= ~(4096UL - 1);
-	monitor_addr = addr;
-
-	/* Reserve memory for malloc() */
-	addr -= CONFIG_SYS_MALLOC_LEN;
-
-#ifdef CONFIG_LCD
-#ifdef CONFIG_FB_ADDR
-	printf("LCD: Frame buffer allocated at preset 0x%08x\n",
-	       CONFIG_FB_ADDR);
-	gd->fb_base = CONFIG_FB_ADDR;
-#else
-	addr = lcd_setmem(addr);
-	printf("LCD: Frame buffer allocated at 0x%08lx\n", addr);
-	gd->fb_base = addr;
-#endif /* CONFIG_FB_ADDR */
-#endif /* CONFIG_LCD */
-
-	/* Allocate a Board Info struct on a word boundary */
-	addr -= sizeof(bd_t);
-	addr &= ~3UL;
-	gd->bd = bd = (bd_t *)addr;
-
-	/* Allocate a new global data copy on a 8-byte boundary. */
-	addr -= sizeof(gd_t);
-	addr &= ~7UL;
-	new_gd = (gd_t *)addr;
-
-	/* And finally, a new, bigger stack. */
-	new_sp = (unsigned long *)addr;
-	gd->start_addr_sp = addr;
-	*(--new_sp) = 0;
-	*(--new_sp) = 0;
-
-	dram_init_banksize();
-
-	memcpy(new_gd, gd, sizeof(gd_t));
-
-	relocate_code((unsigned long)new_sp, new_gd, monitor_addr);
-}
-
-void board_init_r(gd_t *new_gd, ulong dest_addr)
-{
-#ifndef CONFIG_ENV_IS_NOWHERE
-	extern char * env_name_spec;
-#endif
-	bd_t *bd;
-
-	gd = new_gd;
-	bd = gd->bd;
-
-	gd->flags |= GD_FLG_RELOC;
-	gd->reloc_off = dest_addr - CONFIG_SYS_MONITOR_BASE;
-
-	/* Enable the MMU so that we can keep u-boot simple */
-	mmu_init_r(dest_addr);
-
-	board_early_init_r();
-
-	monitor_flash_len = _edata - _text;
-
-#if defined(CONFIG_NEEDS_MANUAL_RELOC)
-	/*
-	 * We have to relocate the command table manually
-	 */
-	fixup_cmdtable(ll_entry_start(cmd_tbl_t, cmd),
-			ll_entry_count(cmd_tbl_t, cmd));
-#endif /* defined(CONFIG_NEEDS_MANUAL_RELOC) */
-
-	/* there are some other pointer constants we must deal with */
-#ifndef CONFIG_ENV_IS_NOWHERE
-	env_name_spec += gd->reloc_off;
-#endif
-
-	timer_init();
-
-	/* The malloc area is right below the monitor image in RAM */
-	mem_malloc_init(CONFIG_SYS_MONITOR_BASE + gd->reloc_off -
-			CONFIG_SYS_MALLOC_LEN, CONFIG_SYS_MALLOC_LEN);
-
-	enable_interrupts();
-
-	bd->bi_flashstart = 0;
-	bd->bi_flashsize = 0;
-	bd->bi_flashoffset = 0;
-
-#ifndef CONFIG_SYS_NO_FLASH
-	bd->bi_flashstart = CONFIG_SYS_FLASH_BASE;
-	bd->bi_flashsize = flash_init();
-	bd->bi_flashoffset = (unsigned long)_edata - (unsigned long)_text;
-
-	if (bd->bi_flashsize)
-		display_flash_config();
-#endif
-
-	if (bd->bi_dram[0].size)
-		display_dram_config();
-
-	gd->bd->bi_boot_params = malloc(CONFIG_SYS_BOOTPARAMS_LEN);
-	if (!gd->bd->bi_boot_params)
-		puts("WARNING: Cannot allocate space for boot parameters\n");
-
-	/* initialize environment */
-	env_relocate();
-
-	stdio_init();
-	jumptable_init();
-	console_init_r();
-
-	/* Initialize from environment */
-	load_addr = getenv_ulong("loadaddr", 16, load_addr);
-
-#ifdef CONFIG_BITBANGMII
-	bb_miiphy_init();
-#endif
-#if defined(CONFIG_CMD_NET)
-	puts("Net:   ");
-	eth_initialize();
-#endif
-
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-	mmc_initialize(gd->bd);
-#endif
-	for (;;) {
-		main_loop();
-	}
-}
-- 
2.1.4

[U-Boot] [PATCH 0/7] avr32: remove non-generic boards

[Hans-Christian Egtvedt]

Around Mon 11 May 2015 13:07:22 +0200 or thereabout, Andreas Bie?mann wrote:
> This series deletes avr32-boards that are still using the ancient
> arch/avr32/lib/board.c code. If one would like his board to stay in u-boot
> there is a last chance to convert it to generic board _now_. It should be as easy
> as defining these three values in the board config:
> 
> |/* generic board */
> |#define CONFIG_SYS_GENERIC_BOARD
> |#define CONFIG_BOARD_EARLY_INIT_F
> |#define CONFIG_BOARD_EARLY_INIT_R

I would prefer this solution over removing all the board support for AVR32
targets in U-Boot.

Sadly, I do not have the time to work with AVR32 in U-Boot.

> The patch 'avr32: delete non generic board favr-32-ezkit' has an checkpatch
> warning which will not be fixed.
> 
> ---8<---
> 0 errors, 1 warnings, 0 checks for 0002-avr32-delete-non-generic-board-favr-32-ezkit.patch:
> warning: arch/avr32/Kconfig,22: please write a paragraph that describes the config symbol fully
> --->8---
> 
> 
> The patch 'avr32: delete non generic board's atstk100{3,4,6}' has a checkpatch
> warning wich will not be fixed.
> 
> ---8<---
> 0 errors, 1 warnings, 0 checks for 0005-avr32-delete-non-generic-board-s-atstk100-3-4-6.patch:
> warning: arch/avr32/Kconfig,13: please write a paragraph that describes the config symbol fully
> --->8---
> 
> 
> 
> Andreas Bie?mann (7):
>   avr32: delete non generic board atngw100
>   avr32: delete non generic board favr-32-ezkit
>   avr32: delete non generic board hammerhead
>   avr32: delete non generic board mimc200
>   avr32: delete non generic board's atstk100{3,4,6}
>   avr32: take maintainership for atstk1002
>   avr32: delete ancient board.c

If one were to prioritize, then keeping the atngw100 board would be great.

If the arch/avr32/lib/board.c is a redundant implementation of the generic
board.c file, then I am all for removing it and move to using the generic
implementation.

<snipp stats>

-- 
Hans-Christian Egtvedt

[U-Boot] [PATCH 0/7] avr32: remove non-generic boards

[Andreas Bießmann]

Hi Hans-Christian,

On 05/11/2015 01:19 PM, Hans-Christian Egtvedt wrote:
> Around Mon 11 May 2015 13:07:22 +0200 or thereabout, Andreas Bie?mann wrote:
>> This series deletes avr32-boards that are still using the ancient
>> arch/avr32/lib/board.c code. If one would like his board to stay in u-boot
>> there is a last chance to convert it to generic board _now_. It should be as easy
>> as defining these three values in the board config:
>>
>> |/* generic board */
>> |#define CONFIG_SYS_GENERIC_BOARD
>> |#define CONFIG_BOARD_EARLY_INIT_F
>> |#define CONFIG_BOARD_EARLY_INIT_R
> 
> I would prefer this solution over removing all the board support for AVR32
> targets in U-Boot.

Me too ...

> Sadly, I do not have the time to work with AVR32 in U-Boot.

... but I'd prefer to run-time test this change on a real hardware.
Unfortunately I do not own any of the removed ones.

<snip>

>> Andreas Bie?mann (7):
>>   avr32: delete non generic board atngw100
>>   avr32: delete non generic board favr-32-ezkit
>>   avr32: delete non generic board hammerhead
>>   avr32: delete non generic board mimc200
>>   avr32: delete non generic board's atstk100{3,4,6}
>>   avr32: take maintainership for atstk1002
>>   avr32: delete ancient board.c
> 
> If one were to prioritize, then keeping the atngw100 board would be great.

+1, but as said above, I want a run-time test and can't do it for my own.
Waldemar talked to me lately to get his ngw100 up running current u-boot
(2015.01 I think). So Waldemar, could you please do a runtime test for
atngw100 and required adoptions? Or anyone else?

Andreas

[U-Boot] [PATCH 0/7] avr32: remove non-generic boards

[Waldemar Brodkorb]

Hi,
Andreas Bie?mann wrote,

> Hi Hans-Christian,
> 
> On 05/11/2015 01:19 PM, Hans-Christian Egtvedt wrote:
> > Around Mon 11 May 2015 13:07:22 +0200 or thereabout, Andreas Bie?mann wrote:
> >> This series deletes avr32-boards that are still using the ancient
> >> arch/avr32/lib/board.c code. If one would like his board to stay in u-boot
> >> there is a last chance to convert it to generic board _now_. It should be as easy
> >> as defining these three values in the board config:
> >>
> >> |/* generic board */
> >> |#define CONFIG_SYS_GENERIC_BOARD
> >> |#define CONFIG_BOARD_EARLY_INIT_F
> >> |#define CONFIG_BOARD_EARLY_INIT_R
> > 
> > I would prefer this solution over removing all the board support for AVR32
> > targets in U-Boot.
> 
> Me too ...
> 
> > Sadly, I do not have the time to work with AVR32 in U-Boot.
> 
> ... but I'd prefer to run-time test this change on a real hardware.
> Unfortunately I do not own any of the removed ones.
> 
> <snip>
> 
> >> Andreas Bie?mann (7):
> >>   avr32: delete non generic board atngw100
> >>   avr32: delete non generic board favr-32-ezkit
> >>   avr32: delete non generic board hammerhead
> >>   avr32: delete non generic board mimc200
> >>   avr32: delete non generic board's atstk100{3,4,6}
> >>   avr32: take maintainership for atstk1002
> >>   avr32: delete ancient board.c
> > 
> > If one were to prioritize, then keeping the atngw100 board would be great.
> 
> +1, but as said above, I want a run-time test and can't do it for my own.
> Waldemar talked to me lately to get his ngw100 up running current u-boot
> (2015.01 I think). So Waldemar, could you please do a runtime test for
> atngw100 and required adoptions? Or anyone else?

I can try a runtime test tommorow. I even now have two devices.
Last time 2015.01 worked, but git with your changes does not.
I have'nt got the time to debug it via JTAG or GDB and I think my
knowledge about the u-boot internals are too bad.

What if I sent you my spare board?

Better one board with good support, then two with no support.

best regards
 Waldemar

[U-Boot] [PATCH 0/7] avr32: remove non-generic boards

[Andreas Bießmann]

Hi Waldemar,

On 05/11/2015 01:32 PM, Waldemar Brodkorb wrote:

>>>> Andreas Bie?mann (7):
>>>>   avr32: delete non generic board atngw100
>>>>   avr32: delete non generic board favr-32-ezkit
>>>>   avr32: delete non generic board hammerhead
>>>>   avr32: delete non generic board mimc200
>>>>   avr32: delete non generic board's atstk100{3,4,6}
>>>>   avr32: take maintainership for atstk1002
>>>>   avr32: delete ancient board.c
>>>
>>> If one were to prioritize, then keeping the atngw100 board would be great.
>>
>> +1, but as said above, I want a run-time test and can't do it for my own.
>> Waldemar talked to me lately to get his ngw100 up running current u-boot
>> (2015.01 I think). So Waldemar, could you please do a runtime test for
>> atngw100 and required adoptions? Or anyone else?
> 
> I can try a runtime test tommorow. I even now have two devices.
> Last time 2015.01 worked, but git with your changes does not.
> I have'nt got the time to debug it via JTAG or GDB and I think my
> knowledge about the u-boot internals are too bad.
> 
> What if I sent you my spare board?

would be an option, if no one else can run the test successfully.

Andreas

[U-Boot] [PATCH 0/7] avr32: remove non-generic boards

[Andreas Bießmann]

Hi Waldemar,

On 05/11/2015 01:32 PM, Waldemar Brodkorb wrote:
> Hi,
> Andreas Bie?mann wrote,
> 
>> Hi Hans-Christian,
>>
>> On 05/11/2015 01:19 PM, Hans-Christian Egtvedt wrote:
>>> Around Mon 11 May 2015 13:07:22 +0200 or thereabout, Andreas Bie?mann wrote:

>>>> Andreas Bie?mann (7):
>>>>   avr32: delete non generic board atngw100
>>>>   avr32: delete non generic board favr-32-ezkit
>>>>   avr32: delete non generic board hammerhead
>>>>   avr32: delete non generic board mimc200
>>>>   avr32: delete non generic board's atstk100{3,4,6}
>>>>   avr32: take maintainership for atstk1002
>>>>   avr32: delete ancient board.c
>>>
>>> If one were to prioritize, then keeping the atngw100 board would be great.
>>
>> +1, but as said above, I want a run-time test and can't do it for my own.
>> Waldemar talked to me lately to get his ngw100 up running current u-boot
>> (2015.01 I think). So Waldemar, could you please do a runtime test for
>> atngw100 and required adoptions? Or anyone else?
> 
> I can try a runtime test tommorow.

any progress? Could you run the test and was it (un)successful?

Andreas

[U-Boot] [PATCH 0/7] avr32: remove non-generic boards

[Waldemar Brodkorb]

Hi Andreas,
Andreas Bie?mann wrote,

> Hi Waldemar,
> 
> On 05/11/2015 01:32 PM, Waldemar Brodkorb wrote:
> > Hi,
> > Andreas Bie?mann wrote,
> > 
> >> Hi Hans-Christian,
> >>
> >> On 05/11/2015 01:19 PM, Hans-Christian Egtvedt wrote:
> >>> Around Mon 11 May 2015 13:07:22 +0200 or thereabout, Andreas Bie?mann wrote:
> 
> >>>> Andreas Bie?mann (7):
> >>>>   avr32: delete non generic board atngw100
> >>>>   avr32: delete non generic board favr-32-ezkit
> >>>>   avr32: delete non generic board hammerhead
> >>>>   avr32: delete non generic board mimc200
> >>>>   avr32: delete non generic board's atstk100{3,4,6}
> >>>>   avr32: take maintainership for atstk1002
> >>>>   avr32: delete ancient board.c
> >>>
> >>> If one were to prioritize, then keeping the atngw100 board would be great.
> >>
> >> +1, but as said above, I want a run-time test and can't do it for my own.
> >> Waldemar talked to me lately to get his ngw100 up running current u-boot
> >> (2015.01 I think). So Waldemar, could you please do a runtime test for
> >> atngw100 and required adoptions? Or anyone else?
> > 
> > I can try a runtime test tommorow.
> 
> any progress? Could you run the test and was it (un)successful?

Got some time today to test.
2015.01 works fine!
git master works fine!
git master with the three line patch added to convert to generic
board support _does not work_!

No ouput on serial console.

best regards
 Waldemar

[U-Boot] [PATCH 0/7] avr32: remove non-generic boards

[Andreas Bießmann]

Hi Waldemar,

On 17.05.15 11:03, Waldemar Brodkorb wrote:
> Hi Andreas,
> Andreas Bie?mann wrote,
> 
>> Hi Waldemar,
>>
>> On 05/11/2015 01:32 PM, Waldemar Brodkorb wrote:
>>> Hi,
>>> Andreas Bie?mann wrote,
>>>
>>>> Hi Hans-Christian,
>>>>
>>>> On 05/11/2015 01:19 PM, Hans-Christian Egtvedt wrote:
>>>>> Around Mon 11 May 2015 13:07:22 +0200 or thereabout, Andreas Bie?mann wrote:
>>
>>>>>> Andreas Bie?mann (7):
>>>>>>   avr32: delete non generic board atngw100
>>>>>>   avr32: delete non generic board favr-32-ezkit
>>>>>>   avr32: delete non generic board hammerhead
>>>>>>   avr32: delete non generic board mimc200
>>>>>>   avr32: delete non generic board's atstk100{3,4,6}
>>>>>>   avr32: take maintainership for atstk1002
>>>>>>   avr32: delete ancient board.c
>>>>>
>>>>> If one were to prioritize, then keeping the atngw100 board would be great.
>>>>
>>>> +1, but as said above, I want a run-time test and can't do it for my own.
>>>> Waldemar talked to me lately to get his ngw100 up running current u-boot
>>>> (2015.01 I think). So Waldemar, could you please do a runtime test for
>>>> atngw100 and required adoptions? Or anyone else?
>>>
>>> I can try a runtime test tommorow.
>>
>> any progress? Could you run the test and was it (un)successful?
> 
> Got some time today to test.
> 2015.01 works fine!
> git master works fine!
> git master with the three line patch added to convert to generic
> board support _does not work_!

Ok, can you debug it? Or will you provide me one of your boards for
generic board support adoption?

Andreas

[U-Boot] [U-Boot,2/7] avr32: delete non generic board favr-32-ezkit

[Andreas Bießmann]

Dear =?utf-8?q?Andreas_Bie=C3=9Fmann?=,

Andreas Devel <andreas.devel@googlemail.com> writes:
>Signed-off-by: Andreas Bie?mann <andreas.devel@googlemail.com>
>---
> arch/avr32/Kconfig                           |   4 -
> board/earthlcd/favr-32-ezkit/Kconfig         |  15 --
> board/earthlcd/favr-32-ezkit/MAINTAINERS     |   6 -
> board/earthlcd/favr-32-ezkit/Makefile        |   9 --
> board/earthlcd/favr-32-ezkit/favr-32-ezkit.c |  81 ----------
> board/earthlcd/favr-32-ezkit/flash.c         | 216 ---------------------------
> configs/favr-32-ezkit_defconfig              |   7 -
> include/configs/favr-32-ezkit.h              | 171 ---------------------
> 8 files changed, 509 deletions(-)
> delete mode 100644 board/earthlcd/favr-32-ezkit/Kconfig
> delete mode 100644 board/earthlcd/favr-32-ezkit/MAINTAINERS
> delete mode 100644 board/earthlcd/favr-32-ezkit/Makefile
> delete mode 100644 board/earthlcd/favr-32-ezkit/favr-32-ezkit.c
> delete mode 100644 board/earthlcd/favr-32-ezkit/flash.c
> delete mode 100644 configs/favr-32-ezkit_defconfig
> delete mode 100644 include/configs/favr-32-ezkit.h

applied to u-boot-avr32/master, thanks!

Best regards,
Andreas Bie?mann

[U-Boot] [U-Boot,3/7] avr32: delete non generic board hammerhead

[Andreas Bießmann]

Dear =?utf-8?q?Andreas_Bie=C3=9Fmann?=,

Andreas Devel <andreas.devel@googlemail.com> writes:
>Signed-off-by: Andreas Bie?mann <andreas.devel@googlemail.com>
>---
> arch/avr32/Kconfig                     |   4 -
> board/miromico/hammerhead/Kconfig      |  15 ----
> board/miromico/hammerhead/MAINTAINERS  |   6 --
> board/miromico/hammerhead/Makefile     |   6 --
> board/miromico/hammerhead/hammerhead.c |  91 --------------------
> configs/hammerhead_defconfig           |   7 --
> include/configs/hammerhead.h           | 147 ---------------------------------
> 7 files changed, 276 deletions(-)
> delete mode 100644 board/miromico/hammerhead/Kconfig
> delete mode 100644 board/miromico/hammerhead/MAINTAINERS
> delete mode 100644 board/miromico/hammerhead/Makefile
> delete mode 100644 board/miromico/hammerhead/hammerhead.c
> delete mode 100644 configs/hammerhead_defconfig
> delete mode 100644 include/configs/hammerhead.h

applied to u-boot-avr32/master, thanks!

Best regards,
Andreas Bie?mann

[U-Boot] [U-Boot,4/7] avr32: delete non generic board mimc200

[Andreas Bießmann]

Dear =?utf-8?q?Andreas_Bie=C3=9Fmann?=,

Andreas Devel <andreas.devel@googlemail.com> writes:
>Signed-off-by: Andreas Bie?mann <andreas.devel@googlemail.com>
>---
> arch/avr32/Kconfig             |   4 -
> board/mimc/mimc200/Kconfig     |  15 ----
> board/mimc/mimc200/MAINTAINERS |   6 --
> board/mimc/mimc200/Makefile    |   6 --
> board/mimc/mimc200/mimc200.c   | 197 -----------------------------------------
> configs/mimc200_defconfig      |   3 -
> include/configs/mimc200.h      | 176 ------------------------------------
> 7 files changed, 407 deletions(-)
> delete mode 100644 board/mimc/mimc200/Kconfig
> delete mode 100644 board/mimc/mimc200/MAINTAINERS
> delete mode 100644 board/mimc/mimc200/Makefile
> delete mode 100644 board/mimc/mimc200/mimc200.c
> delete mode 100644 configs/mimc200_defconfig
> delete mode 100644 include/configs/mimc200.h

applied to u-boot-avr32/master, thanks!

Best regards,
Andreas Bie?mann

[U-Boot] [U-Boot,5/7] avr32: delete non generic board's atstk100{3, 4, 6}

[Andreas Bießmann]

Dear =?utf-8?q?Andreas_Bie=C3=9Fmann?=,

Andreas Devel <andreas.devel@googlemail.com> writes:
>Signed-off-by: Andreas Bie?mann <andreas.devel@googlemail.com>
>---
> arch/avr32/Kconfig                |   9 --
> board/atmel/atstk1000/Kconfig     |  48 -----------
> board/atmel/atstk1000/MAINTAINERS |   6 --
> board/atmel/atstk1000/atstk1000.c |  23 +-----
> configs/atstk1003_defconfig       |   6 --
> configs/atstk1004_defconfig       |   6 --
> configs/atstk1006_defconfig       |   7 --
> include/configs/atstk1003.h       | 150 ----------------------------------
> include/configs/atstk1004.h       | 150 ----------------------------------
> include/configs/atstk1006.h       | 168 --------------------------------------
> 10 files changed, 1 insertion(+), 572 deletions(-)
> delete mode 100644 configs/atstk1003_defconfig
> delete mode 100644 configs/atstk1004_defconfig
> delete mode 100644 configs/atstk1006_defconfig
> delete mode 100644 include/configs/atstk1003.h
> delete mode 100644 include/configs/atstk1004.h
> delete mode 100644 include/configs/atstk1006.h

applied to u-boot-avr32/master, thanks!

Best regards,
Andreas Bie?mann

[U-Boot] [U-Boot,6/7] avr32: take maintainership for atstk1002

[Andreas Bießmann]

Dear =?utf-8?q?Andreas_Bie=C3=9Fmann?=,

Andreas Devel <andreas.devel@googlemail.com> writes:
>I have this board at work, so I can trun tests on it.
>
>Signed-off-by: Andreas Bie?mann <andreas.devel@googlemail.com>
>---
>
> board/atmel/atstk1000/MAINTAINERS | 4 ++--
> 1 file changed, 2 insertions(+), 2 deletions(-)

applied to u-boot-avr32/master, thanks!

Best regards,
Andreas Bie?mann

[U-Boot] [U-Boot,7/7] avr32: delete ancient board.c

[Andreas Bießmann]

Dear =?utf-8?q?Andreas_Bie=C3=9Fmann?=,

Andreas Devel <andreas.devel@googlemail.com> writes:
>Signed-off-by: Andreas Bie?mann <andreas.devel@googlemail.com>
>---
>
> arch/avr32/lib/Makefile |   3 -
> arch/avr32/lib/board.c  | 256 ------------------------------------------------
> 2 files changed, 259 deletions(-)
> delete mode 100644 arch/avr32/lib/board.c

applied to u-boot-avr32/master, thanks!

Best regards,
Andreas Bie?mann