* [PATCH v4 0/3] ARM: dts: imx6: Support Poslab Savageboard dual & quad
@ 2017-01-04 4:55 ` Milo Kim
0 siblings, 0 replies; 15+ messages in thread
From: Milo Kim @ 2017-01-04 4:55 UTC (permalink / raw)
To: Shawn Guo, Sascha Hauer
Cc: Fabio Estevam, linux-arm-kernel, devicetree, linux-kernel, Milo Kim
Poslab Savageboard is the i.MX6 SoC base, but BSP code from the vendor is
not mainline u-boot and kernel. Personal reason of using this board is
testing etnaviv user-space driver, so I re-write device tree files based on
mainline kernel for the first step.
This patchset includes common DT file, dual and quad board files.
Supported components are
- Display: HDMI and LVDS panel
- eMMC and SD card
- Ethernet
- Pinmux configuration
- SATA: only for Savageboard quad
- UART1 for debug console
- USB host
Missing features are
- Audio (WM8903)
- USB OTG
- PMIC WM8326: default settings are used so no issue to bring-up the system
- MIPI DSI and CSI
Patches are tested on the Savageboard quad but the dual version should work
because the only difference between dual and quad is SATA support.
More information in http://www.savageboard.org
v4:
Fix the license text and add the vendor prefix.
Use generic node name for the backlight panel.
Sort alphabetically for the pinctrl nodes.
Remove unnecessary pinmux of HDMI CEC.
v3:
Specify the dtbs for i.MX6 build.
v2:
Fix DT node for regulator, phy-reset-gpios and iomuxc node.
Milo Kim (3):
ARM: dts: imx6: Add Savageboard common file
ARM: dts: imx6: Support Savageboard dual
ARM: dts: imx6: Support Savageboard quad
.../devicetree/bindings/vendor-prefixes.txt | 1 +
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6dl-savageboard.dts | 51 +++++
arch/arm/boot/dts/imx6q-savageboard.dts | 55 +++++
arch/arm/boot/dts/imx6qdl-savageboard.dtsi | 255 +++++++++++++++++++++
5 files changed, 364 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-savageboard.dts
create mode 100644 arch/arm/boot/dts/imx6q-savageboard.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-savageboard.dtsi
--
2.11.0
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v4 0/3] ARM: dts: imx6: Support Poslab Savageboard dual & quad
@ 2017-01-04 4:55 ` Milo Kim
0 siblings, 0 replies; 15+ messages in thread
From: Milo Kim @ 2017-01-04 4:55 UTC (permalink / raw)
To: Shawn Guo, Sascha Hauer
Cc: Fabio Estevam, devicetree, Milo Kim, linux-kernel, linux-arm-kernel
Poslab Savageboard is the i.MX6 SoC base, but BSP code from the vendor is
not mainline u-boot and kernel. Personal reason of using this board is
testing etnaviv user-space driver, so I re-write device tree files based on
mainline kernel for the first step.
This patchset includes common DT file, dual and quad board files.
Supported components are
- Display: HDMI and LVDS panel
- eMMC and SD card
- Ethernet
- Pinmux configuration
- SATA: only for Savageboard quad
- UART1 for debug console
- USB host
Missing features are
- Audio (WM8903)
- USB OTG
- PMIC WM8326: default settings are used so no issue to bring-up the system
- MIPI DSI and CSI
Patches are tested on the Savageboard quad but the dual version should work
because the only difference between dual and quad is SATA support.
More information in http://www.savageboard.org
v4:
Fix the license text and add the vendor prefix.
Use generic node name for the backlight panel.
Sort alphabetically for the pinctrl nodes.
Remove unnecessary pinmux of HDMI CEC.
v3:
Specify the dtbs for i.MX6 build.
v2:
Fix DT node for regulator, phy-reset-gpios and iomuxc node.
Milo Kim (3):
ARM: dts: imx6: Add Savageboard common file
ARM: dts: imx6: Support Savageboard dual
ARM: dts: imx6: Support Savageboard quad
.../devicetree/bindings/vendor-prefixes.txt | 1 +
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6dl-savageboard.dts | 51 +++++
arch/arm/boot/dts/imx6q-savageboard.dts | 55 +++++
arch/arm/boot/dts/imx6qdl-savageboard.dtsi | 255 +++++++++++++++++++++
5 files changed, 364 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-savageboard.dts
create mode 100644 arch/arm/boot/dts/imx6q-savageboard.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-savageboard.dtsi
--
2.11.0
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v4 0/3] ARM: dts: imx6: Support Poslab Savageboard dual & quad
@ 2017-01-04 4:55 ` Milo Kim
0 siblings, 0 replies; 15+ messages in thread
From: Milo Kim @ 2017-01-04 4:55 UTC (permalink / raw)
To: linux-arm-kernel
Poslab Savageboard is the i.MX6 SoC base, but BSP code from the vendor is
not mainline u-boot and kernel. Personal reason of using this board is
testing etnaviv user-space driver, so I re-write device tree files based on
mainline kernel for the first step.
This patchset includes common DT file, dual and quad board files.
Supported components are
- Display: HDMI and LVDS panel
- eMMC and SD card
- Ethernet
- Pinmux configuration
- SATA: only for Savageboard quad
- UART1 for debug console
- USB host
Missing features are
- Audio (WM8903)
- USB OTG
- PMIC WM8326: default settings are used so no issue to bring-up the system
- MIPI DSI and CSI
Patches are tested on the Savageboard quad but the dual version should work
because the only difference between dual and quad is SATA support.
More information in http://www.savageboard.org
v4:
Fix the license text and add the vendor prefix.
Use generic node name for the backlight panel.
Sort alphabetically for the pinctrl nodes.
Remove unnecessary pinmux of HDMI CEC.
v3:
Specify the dtbs for i.MX6 build.
v2:
Fix DT node for regulator, phy-reset-gpios and iomuxc node.
Milo Kim (3):
ARM: dts: imx6: Add Savageboard common file
ARM: dts: imx6: Support Savageboard dual
ARM: dts: imx6: Support Savageboard quad
.../devicetree/bindings/vendor-prefixes.txt | 1 +
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6dl-savageboard.dts | 51 +++++
arch/arm/boot/dts/imx6q-savageboard.dts | 55 +++++
arch/arm/boot/dts/imx6qdl-savageboard.dtsi | 255 +++++++++++++++++++++
5 files changed, 364 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-savageboard.dts
create mode 100644 arch/arm/boot/dts/imx6q-savageboard.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-savageboard.dtsi
--
2.11.0
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v4 1/3] ARM: dts: imx6: Add Savageboard common file
2017-01-04 4:55 ` Milo Kim
(?)
@ 2017-01-04 4:55 ` Milo Kim
-1 siblings, 0 replies; 15+ messages in thread
From: Milo Kim @ 2017-01-04 4:55 UTC (permalink / raw)
To: Shawn Guo, Sascha Hauer
Cc: Fabio Estevam, linux-arm-kernel, devicetree, linux-kernel, Milo Kim
* Memory
memblock for DDR3 1GB
* Regulator
3.3V for panel and backlight.
* Display
Enable HDMI and LVDS panel. Savageboard supports AVIC TM097TDH02 panel
which is compatible with Hannstar HSD100PXN1, so reuse it.
* Clock
The commit d28be499c45e6 ("ARM: dts: imx6qdl-sabresd: Allow HDMI and
LVDS to work simultaneously") is applied to support LVDS and HDMI output
at the same time.
* Pinmux
Support eMMC, ethernet, gpio key for power button, I2C, PWM, SD card
and UART.
* Others
Enable ethernet, UART1 debug, USB host, USDHC3 for microSD card and
USDHC4 for built-in eMMC storage.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
---
arch/arm/boot/dts/imx6qdl-savageboard.dtsi | 255 +++++++++++++++++++++++++++++
1 file changed, 255 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6qdl-savageboard.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-savageboard.dtsi b/arch/arm/boot/dts/imx6qdl-savageboard.dtsi
new file mode 100644
index 000000000000..a616e3c400d3
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-savageboard.dtsi
@@ -0,0 +1,255 @@
+/*
+ * Copyright (C) 2017 Milo Kim <woogyom.kim@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x40000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ power {
+ gpios = <&gpio3 7 GPIO_ACTIVE_LOW>;
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ panel {
+ compatible = "avic,tm097tdh02", "hannstar,hsd100pxn1";
+ backlight = <&panel_bl>;
+ power-supply = <®_3p3v>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+
+ panel_bl: backlight {
+ compatible = "pwm-backlight";
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <4>;
+ power-supply = <®_3p3v>;
+ pwms = <&pwm1 0 10000>;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+ <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&fec {
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ status = "okay";
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ reg = <0>;
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+/* SD card */
+&usdhc3 {
+ bus-width = <4>;
+ cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sd>;
+ status = "okay";
+};
+
+/* eMMC */
+&usdhc4 {
+ bus-width = <8>;
+ keep-power-in-suspend;
+ no-1-8-v;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_emmc>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_emmc: emmcgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
+ MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
+ MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
+ MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
+ MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ /* PHY reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpio_keys: gpiokeysgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x1b0b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_sd: sdgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ /* CD pin */
+ MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v4 1/3] ARM: dts: imx6: Add Savageboard common file
@ 2017-01-04 4:55 ` Milo Kim
0 siblings, 0 replies; 15+ messages in thread
From: Milo Kim @ 2017-01-04 4:55 UTC (permalink / raw)
To: Shawn Guo, Sascha Hauer
Cc: Fabio Estevam, devicetree, Milo Kim, linux-kernel, linux-arm-kernel
* Memory
memblock for DDR3 1GB
* Regulator
3.3V for panel and backlight.
* Display
Enable HDMI and LVDS panel. Savageboard supports AVIC TM097TDH02 panel
which is compatible with Hannstar HSD100PXN1, so reuse it.
* Clock
The commit d28be499c45e6 ("ARM: dts: imx6qdl-sabresd: Allow HDMI and
LVDS to work simultaneously") is applied to support LVDS and HDMI output
at the same time.
* Pinmux
Support eMMC, ethernet, gpio key for power button, I2C, PWM, SD card
and UART.
* Others
Enable ethernet, UART1 debug, USB host, USDHC3 for microSD card and
USDHC4 for built-in eMMC storage.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
---
arch/arm/boot/dts/imx6qdl-savageboard.dtsi | 255 +++++++++++++++++++++++++++++
1 file changed, 255 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6qdl-savageboard.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-savageboard.dtsi b/arch/arm/boot/dts/imx6qdl-savageboard.dtsi
new file mode 100644
index 000000000000..a616e3c400d3
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-savageboard.dtsi
@@ -0,0 +1,255 @@
+/*
+ * Copyright (C) 2017 Milo Kim <woogyom.kim@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x40000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ power {
+ gpios = <&gpio3 7 GPIO_ACTIVE_LOW>;
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ panel {
+ compatible = "avic,tm097tdh02", "hannstar,hsd100pxn1";
+ backlight = <&panel_bl>;
+ power-supply = <®_3p3v>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+
+ panel_bl: backlight {
+ compatible = "pwm-backlight";
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <4>;
+ power-supply = <®_3p3v>;
+ pwms = <&pwm1 0 10000>;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+ <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&fec {
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ status = "okay";
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ reg = <0>;
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+/* SD card */
+&usdhc3 {
+ bus-width = <4>;
+ cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sd>;
+ status = "okay";
+};
+
+/* eMMC */
+&usdhc4 {
+ bus-width = <8>;
+ keep-power-in-suspend;
+ no-1-8-v;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_emmc>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_emmc: emmcgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
+ MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
+ MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
+ MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
+ MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ /* PHY reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpio_keys: gpiokeysgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x1b0b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_sd: sdgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ /* CD pin */
+ MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v4 1/3] ARM: dts: imx6: Add Savageboard common file
@ 2017-01-04 4:55 ` Milo Kim
0 siblings, 0 replies; 15+ messages in thread
From: Milo Kim @ 2017-01-04 4:55 UTC (permalink / raw)
To: linux-arm-kernel
* Memory
memblock for DDR3 1GB
* Regulator
3.3V for panel and backlight.
* Display
Enable HDMI and LVDS panel. Savageboard supports AVIC TM097TDH02 panel
which is compatible with Hannstar HSD100PXN1, so reuse it.
* Clock
The commit d28be499c45e6 ("ARM: dts: imx6qdl-sabresd: Allow HDMI and
LVDS to work simultaneously") is applied to support LVDS and HDMI output
at the same time.
* Pinmux
Support eMMC, ethernet, gpio key for power button, I2C, PWM, SD card
and UART.
* Others
Enable ethernet, UART1 debug, USB host, USDHC3 for microSD card and
USDHC4 for built-in eMMC storage.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
---
arch/arm/boot/dts/imx6qdl-savageboard.dtsi | 255 +++++++++++++++++++++++++++++
1 file changed, 255 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6qdl-savageboard.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-savageboard.dtsi b/arch/arm/boot/dts/imx6qdl-savageboard.dtsi
new file mode 100644
index 000000000000..a616e3c400d3
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-savageboard.dtsi
@@ -0,0 +1,255 @@
+/*
+ * Copyright (C) 2017 Milo Kim <woogyom.kim@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory at 10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x40000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ power {
+ gpios = <&gpio3 7 GPIO_ACTIVE_LOW>;
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ panel {
+ compatible = "avic,tm097tdh02", "hannstar,hsd100pxn1";
+ backlight = <&panel_bl>;
+ power-supply = <®_3p3v>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+
+ panel_bl: backlight {
+ compatible = "pwm-backlight";
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <4>;
+ power-supply = <®_3p3v>;
+ pwms = <&pwm1 0 10000>;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+ <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&fec {
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ status = "okay";
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel at 0 {
+ reg = <0>;
+ status = "okay";
+
+ port at 4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+/* SD card */
+&usdhc3 {
+ bus-width = <4>;
+ cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sd>;
+ status = "okay";
+};
+
+/* eMMC */
+&usdhc4 {
+ bus-width = <8>;
+ keep-power-in-suspend;
+ no-1-8-v;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_emmc>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_emmc: emmcgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
+ MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
+ MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
+ MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
+ MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ /* PHY reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpio_keys: gpiokeysgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x1b0b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_sd: sdgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ /* CD pin */
+ MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v4 2/3] ARM: dts: imx6: Support Savageboard dual
2017-01-04 4:55 ` Milo Kim
(?)
@ 2017-01-04 4:55 ` Milo Kim
-1 siblings, 0 replies; 15+ messages in thread
From: Milo Kim @ 2017-01-04 4:55 UTC (permalink / raw)
To: Shawn Guo, Sascha Hauer
Cc: Fabio Estevam, linux-arm-kernel, devicetree, linux-kernel, Milo Kim
Common savageboard DT file is used for board support.
Add the vendor name and specify the dtb file for i.MX6Q build.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
---
.../devicetree/bindings/vendor-prefixes.txt | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-savageboard.dts | 51 ++++++++++++++++++++++
3 files changed, 53 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-savageboard.dts
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 16d3b5e7f5d1..88c33d827e51 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -227,6 +227,7 @@ pine64 Pine64
pixcir PIXCIR MICROELECTRONICS Co., Ltd
plathome Plat'Home Co., Ltd.
plda PLDA
+poslab Poslab Technology Co., Ltd.
powervr PowerVR (deprecated, use img)
pulsedlight PulsedLight, Inc
qca Qualcomm Atheros, Inc.
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index cccdbcb557b6..fb7f904a5235 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -357,6 +357,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-sabreauto.dtb \
imx6dl-sabrelite.dtb \
imx6dl-sabresd.dtb \
+ imx6dl-savageboard.dtb \
imx6dl-ts4900.dtb \
imx6dl-tx6dl-comtft.dtb \
imx6dl-tx6s-8034.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-savageboard.dts b/arch/arm/boot/dts/imx6dl-savageboard.dts
new file mode 100644
index 000000000000..b95469c520a4
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-savageboard.dts
@@ -0,0 +1,51 @@
+/*
+ * Copyright (C) 2017 Milo Kim <woogyom.kim@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-savageboard.dtsi"
+
+/ {
+ model = "Poslab SavageBoard Dual";
+ compatible = "poslab,imx6dl-savageboard", "fsl,imx6dl";
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v4 2/3] ARM: dts: imx6: Support Savageboard dual
@ 2017-01-04 4:55 ` Milo Kim
0 siblings, 0 replies; 15+ messages in thread
From: Milo Kim @ 2017-01-04 4:55 UTC (permalink / raw)
To: Shawn Guo, Sascha Hauer
Cc: Fabio Estevam, devicetree, Milo Kim, linux-kernel, linux-arm-kernel
Common savageboard DT file is used for board support.
Add the vendor name and specify the dtb file for i.MX6Q build.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
---
.../devicetree/bindings/vendor-prefixes.txt | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-savageboard.dts | 51 ++++++++++++++++++++++
3 files changed, 53 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-savageboard.dts
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 16d3b5e7f5d1..88c33d827e51 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -227,6 +227,7 @@ pine64 Pine64
pixcir PIXCIR MICROELECTRONICS Co., Ltd
plathome Plat'Home Co., Ltd.
plda PLDA
+poslab Poslab Technology Co., Ltd.
powervr PowerVR (deprecated, use img)
pulsedlight PulsedLight, Inc
qca Qualcomm Atheros, Inc.
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index cccdbcb557b6..fb7f904a5235 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -357,6 +357,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-sabreauto.dtb \
imx6dl-sabrelite.dtb \
imx6dl-sabresd.dtb \
+ imx6dl-savageboard.dtb \
imx6dl-ts4900.dtb \
imx6dl-tx6dl-comtft.dtb \
imx6dl-tx6s-8034.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-savageboard.dts b/arch/arm/boot/dts/imx6dl-savageboard.dts
new file mode 100644
index 000000000000..b95469c520a4
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-savageboard.dts
@@ -0,0 +1,51 @@
+/*
+ * Copyright (C) 2017 Milo Kim <woogyom.kim@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-savageboard.dtsi"
+
+/ {
+ model = "Poslab SavageBoard Dual";
+ compatible = "poslab,imx6dl-savageboard", "fsl,imx6dl";
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v4 2/3] ARM: dts: imx6: Support Savageboard dual
@ 2017-01-04 4:55 ` Milo Kim
0 siblings, 0 replies; 15+ messages in thread
From: Milo Kim @ 2017-01-04 4:55 UTC (permalink / raw)
To: linux-arm-kernel
Common savageboard DT file is used for board support.
Add the vendor name and specify the dtb file for i.MX6Q build.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
---
.../devicetree/bindings/vendor-prefixes.txt | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-savageboard.dts | 51 ++++++++++++++++++++++
3 files changed, 53 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-savageboard.dts
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 16d3b5e7f5d1..88c33d827e51 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -227,6 +227,7 @@ pine64 Pine64
pixcir PIXCIR MICROELECTRONICS Co., Ltd
plathome Plat'Home Co., Ltd.
plda PLDA
+poslab Poslab Technology Co., Ltd.
powervr PowerVR (deprecated, use img)
pulsedlight PulsedLight, Inc
qca Qualcomm Atheros, Inc.
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index cccdbcb557b6..fb7f904a5235 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -357,6 +357,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-sabreauto.dtb \
imx6dl-sabrelite.dtb \
imx6dl-sabresd.dtb \
+ imx6dl-savageboard.dtb \
imx6dl-ts4900.dtb \
imx6dl-tx6dl-comtft.dtb \
imx6dl-tx6s-8034.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-savageboard.dts b/arch/arm/boot/dts/imx6dl-savageboard.dts
new file mode 100644
index 000000000000..b95469c520a4
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-savageboard.dts
@@ -0,0 +1,51 @@
+/*
+ * Copyright (C) 2017 Milo Kim <woogyom.kim@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-savageboard.dtsi"
+
+/ {
+ model = "Poslab SavageBoard Dual";
+ compatible = "poslab,imx6dl-savageboard", "fsl,imx6dl";
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v4 3/3] ARM: dts: imx6: Support Savageboard quad
2017-01-04 4:55 ` Milo Kim
(?)
@ 2017-01-04 4:55 ` Milo Kim
-1 siblings, 0 replies; 15+ messages in thread
From: Milo Kim @ 2017-01-04 4:55 UTC (permalink / raw)
To: Shawn Guo, Sascha Hauer
Cc: Fabio Estevam, linux-arm-kernel, devicetree, linux-kernel, Milo Kim
Use common board file and support SATA interface additionally.
Specify the dtb file for i.MX6 build.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-savageboard.dts | 55 +++++++++++++++++++++++++++++++++
2 files changed, 56 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-savageboard.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index fb7f904a5235..2f21e59adc1e 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -403,6 +403,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-sabreauto.dtb \
imx6q-sabrelite.dtb \
imx6q-sabresd.dtb \
+ imx6q-savageboard.dtb \
imx6q-sbc6x.dtb \
imx6q-tbs2910.dtb \
imx6q-ts4900.dtb \
diff --git a/arch/arm/boot/dts/imx6q-savageboard.dts b/arch/arm/boot/dts/imx6q-savageboard.dts
new file mode 100644
index 000000000000..717ac62fc2cf
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-savageboard.dts
@@ -0,0 +1,55 @@
+/*
+ * Copyright (C) 2017 Milo Kim <woogyom.kim@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-savageboard.dtsi"
+
+/ {
+ model = "Poslab SavageBoard Quad";
+ compatible = "poslab,imx6q-savageboard", "fsl,imx6q";
+};
+
+&sata {
+ status = "okay";
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v4 3/3] ARM: dts: imx6: Support Savageboard quad
@ 2017-01-04 4:55 ` Milo Kim
0 siblings, 0 replies; 15+ messages in thread
From: Milo Kim @ 2017-01-04 4:55 UTC (permalink / raw)
To: Shawn Guo, Sascha Hauer
Cc: Fabio Estevam, devicetree, Milo Kim, linux-kernel, linux-arm-kernel
Use common board file and support SATA interface additionally.
Specify the dtb file for i.MX6 build.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-savageboard.dts | 55 +++++++++++++++++++++++++++++++++
2 files changed, 56 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-savageboard.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index fb7f904a5235..2f21e59adc1e 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -403,6 +403,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-sabreauto.dtb \
imx6q-sabrelite.dtb \
imx6q-sabresd.dtb \
+ imx6q-savageboard.dtb \
imx6q-sbc6x.dtb \
imx6q-tbs2910.dtb \
imx6q-ts4900.dtb \
diff --git a/arch/arm/boot/dts/imx6q-savageboard.dts b/arch/arm/boot/dts/imx6q-savageboard.dts
new file mode 100644
index 000000000000..717ac62fc2cf
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-savageboard.dts
@@ -0,0 +1,55 @@
+/*
+ * Copyright (C) 2017 Milo Kim <woogyom.kim@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-savageboard.dtsi"
+
+/ {
+ model = "Poslab SavageBoard Quad";
+ compatible = "poslab,imx6q-savageboard", "fsl,imx6q";
+};
+
+&sata {
+ status = "okay";
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v4 3/3] ARM: dts: imx6: Support Savageboard quad
@ 2017-01-04 4:55 ` Milo Kim
0 siblings, 0 replies; 15+ messages in thread
From: Milo Kim @ 2017-01-04 4:55 UTC (permalink / raw)
To: linux-arm-kernel
Use common board file and support SATA interface additionally.
Specify the dtb file for i.MX6 build.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-savageboard.dts | 55 +++++++++++++++++++++++++++++++++
2 files changed, 56 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-savageboard.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index fb7f904a5235..2f21e59adc1e 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -403,6 +403,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-sabreauto.dtb \
imx6q-sabrelite.dtb \
imx6q-sabresd.dtb \
+ imx6q-savageboard.dtb \
imx6q-sbc6x.dtb \
imx6q-tbs2910.dtb \
imx6q-ts4900.dtb \
diff --git a/arch/arm/boot/dts/imx6q-savageboard.dts b/arch/arm/boot/dts/imx6q-savageboard.dts
new file mode 100644
index 000000000000..717ac62fc2cf
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-savageboard.dts
@@ -0,0 +1,55 @@
+/*
+ * Copyright (C) 2017 Milo Kim <woogyom.kim@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-savageboard.dtsi"
+
+/ {
+ model = "Poslab SavageBoard Quad";
+ compatible = "poslab,imx6q-savageboard", "fsl,imx6q";
+};
+
+&sata {
+ status = "okay";
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [PATCH v4 2/3] ARM: dts: imx6: Support Savageboard dual
2017-01-04 4:55 ` Milo Kim
(?)
@ 2017-01-04 7:12 ` Milo Kim
-1 siblings, 0 replies; 15+ messages in thread
From: Milo Kim @ 2017-01-04 7:12 UTC (permalink / raw)
To: Shawn Guo, Sascha Hauer
Cc: Fabio Estevam, linux-arm-kernel, devicetree, linux-kernel
On 01/04/2017 01:55 PM, Milo Kim wrote:
> Common savageboard DT file is used for board support.
> Add the vendor name and specify the dtb file for i.MX6Q build.
>
> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
> Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
> ---
> .../devicetree/bindings/vendor-prefixes.txt | 1 +
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6dl-savageboard.dts | 51 ++++++++++++++++++++++
> 3 files changed, 53 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-savageboard.dts
>
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index 16d3b5e7f5d1..88c33d827e51 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -227,6 +227,7 @@ pine64 Pine64
> pixcir PIXCIR MICROELECTRONICS Co., Ltd
> plathome Plat'Home Co., Ltd.
> plda PLDA
> +poslab Poslab Technology Co., Ltd.
I should input tab here instead of spaces, so updated single patch was
just sent. Please refer to the patch named "[PATCH resend v4 2/3] ARM:
dts: imx6: Support Savageboard dual".
Sorry for the inconvenience.
Best regards,
Milo
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v4 2/3] ARM: dts: imx6: Support Savageboard dual
@ 2017-01-04 7:12 ` Milo Kim
0 siblings, 0 replies; 15+ messages in thread
From: Milo Kim @ 2017-01-04 7:12 UTC (permalink / raw)
To: Shawn Guo, Sascha Hauer
Cc: Fabio Estevam, devicetree, linux-kernel, linux-arm-kernel
On 01/04/2017 01:55 PM, Milo Kim wrote:
> Common savageboard DT file is used for board support.
> Add the vendor name and specify the dtb file for i.MX6Q build.
>
> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
> Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
> ---
> .../devicetree/bindings/vendor-prefixes.txt | 1 +
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6dl-savageboard.dts | 51 ++++++++++++++++++++++
> 3 files changed, 53 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-savageboard.dts
>
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index 16d3b5e7f5d1..88c33d827e51 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -227,6 +227,7 @@ pine64 Pine64
> pixcir PIXCIR MICROELECTRONICS Co., Ltd
> plathome Plat'Home Co., Ltd.
> plda PLDA
> +poslab Poslab Technology Co., Ltd.
I should input tab here instead of spaces, so updated single patch was
just sent. Please refer to the patch named "[PATCH resend v4 2/3] ARM:
dts: imx6: Support Savageboard dual".
Sorry for the inconvenience.
Best regards,
Milo
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v4 2/3] ARM: dts: imx6: Support Savageboard dual
@ 2017-01-04 7:12 ` Milo Kim
0 siblings, 0 replies; 15+ messages in thread
From: Milo Kim @ 2017-01-04 7:12 UTC (permalink / raw)
To: linux-arm-kernel
On 01/04/2017 01:55 PM, Milo Kim wrote:
> Common savageboard DT file is used for board support.
> Add the vendor name and specify the dtb file for i.MX6Q build.
>
> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
> Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
> ---
> .../devicetree/bindings/vendor-prefixes.txt | 1 +
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6dl-savageboard.dts | 51 ++++++++++++++++++++++
> 3 files changed, 53 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-savageboard.dts
>
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index 16d3b5e7f5d1..88c33d827e51 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -227,6 +227,7 @@ pine64 Pine64
> pixcir PIXCIR MICROELECTRONICS Co., Ltd
> plathome Plat'Home Co., Ltd.
> plda PLDA
> +poslab Poslab Technology Co., Ltd.
I should input tab here instead of spaces, so updated single patch was
just sent. Please refer to the patch named "[PATCH resend v4 2/3] ARM:
dts: imx6: Support Savageboard dual".
Sorry for the inconvenience.
Best regards,
Milo
^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2017-01-04 7:15 UTC | newest]
Thread overview: 15+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-01-04 4:55 [PATCH v4 0/3] ARM: dts: imx6: Support Poslab Savageboard dual & quad Milo Kim
2017-01-04 4:55 ` Milo Kim
2017-01-04 4:55 ` Milo Kim
2017-01-04 4:55 ` [PATCH v4 1/3] ARM: dts: imx6: Add Savageboard common file Milo Kim
2017-01-04 4:55 ` Milo Kim
2017-01-04 4:55 ` Milo Kim
2017-01-04 4:55 ` [PATCH v4 2/3] ARM: dts: imx6: Support Savageboard dual Milo Kim
2017-01-04 4:55 ` Milo Kim
2017-01-04 4:55 ` Milo Kim
2017-01-04 7:12 ` Milo Kim
2017-01-04 7:12 ` Milo Kim
2017-01-04 7:12 ` Milo Kim
2017-01-04 4:55 ` [PATCH v4 3/3] ARM: dts: imx6: Support Savageboard quad Milo Kim
2017-01-04 4:55 ` Milo Kim
2017-01-04 4:55 ` Milo Kim
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.