* ATA failure regression in kernel 4.2
@ 2015-07-23 17:48 Alex Deucher
2015-07-23 18:35 ` Tejun Heo
0 siblings, 1 reply; 15+ messages in thread
From: Alex Deucher @ 2015-07-23 17:48 UTC (permalink / raw)
To: LKML
Something new in kernel 4.2 seems to have broken one of my hard drives
(ssd) in kernel 4.2. 4.1 and older kernels work fine. Here are the
relevant logs.
Kernel 4.1:
[ 1.435809] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.435837] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.444814] input: Logitech Inc. iFeel Mouse as
/devices/pci0000:00/0000:00:10.0/usb1/1-1/1-1:1.0/0003:046D:C030.0001/input/input3
[ 1.445156] hid-generic 0003:046D:C030.0001: input,hidraw0: USB HID
v1.00 Mouse [Logitech Inc. iFeel Mouse ] on
usb-0000:00:10.0-1/input0
[ 1.447770] ata2.00: ATA-8: KINGSTON SV300S37A120G, 506ABBF0, max UDMA/133
[ 1.447773] ata2.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.457610] ata2.00: configured for UDMA/133
[ 1.472799] ata1.00: HPA detected: current 156299375, native 156301488
[ 1.472805] ata1.00: ATA-7: ST380815AS, 4.AAB, max UDMA/133
[ 1.472807] ata1.00: 156299375 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.531057] ata1.00: configured for UDMA/133
[ 1.531223] scsi 0:0:0:0: Direct-Access ATA ST380815AS
B PQ: 0 ANSI: 5
[ 1.531438] sd 0:0:0:0: [sda] 156299375 512-byte logical blocks:
(80.0 GB/74.5 GiB)
[ 1.531476] sd 0:0:0:0: [sda] Write Protect is off
[ 1.531478] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.531484] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.531491] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.531686] scsi 1:0:0:0: Direct-Access ATA KINGSTON
SV300S3 BBF0 PQ: 0 ANSI: 5
[ 1.531847] sd 1:0:0:0: [sdb] 234441648 512-byte logical blocks:
(120 GB/111 GiB)
[ 1.531879] sd 1:0:0:0: [sdb] Write Protect is off
[ 1.531881] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.531891] sd 1:0:0:0: [sdb] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.531904] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 1.534210] sdb: sdb1
[ 1.534466] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 1.579337] sda: sda1
[ 1.579628] sd 0:0:0:0: [sda] Attached SCSI disk
Kernel 4.2:
[ 1.552246] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.552308] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.568731] input: Logitech Inc. iFeel Mouse as
/devices/pci0000:00/0000:00:10.0/usb1/1-1/1-1:1.0/0003:046D:C030.0001/input/input3
[ 1.569086] hid-generic 0003:046D:C030.0001: input,hidraw0: USB HID
v1.00 Mouse [Logitech Inc. iFeel Mouse ] on
usb-0000:00:10.0-1/input0
[ 1.597811] ata1.00: HPA detected: current 156299375, native 156301488
[ 1.597900] ata1.00: ATA-7: ST380815AS, 4.AAB, max UDMA/133
[ 1.597983] ata1.00: 156299375 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.656075] ata1.00: configured for UDMA/133
[ 1.656417] scsi 0:0:0:0: Direct-Access ATA ST380815AS
B PQ: 0 ANSI: 5
[ 1.656744] sd 0:0:0:0: [sda] 156299375 512-byte logical blocks:
(80.0 GB/74.5 GiB)
[ 1.656801] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.657071] sd 0:0:0:0: [sda] Write Protect is off
[ 1.657166] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.657201] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.704347] sda: sda1
[ 1.704779] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.059840] tsc: Refined TSC clocksource calibration: 3693.283 MHz
[ 2.059936] clocksource: tsc: mask: 0xffffffffffffffff max_cycles:
0x6a7918f751d, max_idle_ns: 881590915016 ns
[ 3.059155] clocksource: Switched to clocksource tsc
[ 6.547628] ata2.00: qc timeout (cmd 0xec)
[ 6.547721] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 7.007213] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 16.997819] ata2.00: qc timeout (cmd 0xec)
[ 16.997910] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 16.997995] ata2: limiting SATA link speed to 3.0 Gbps
[ 17.457400] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 47.429257] ata2.00: qc timeout (cmd 0xec)
[ 47.429349] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 47.888822] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
Any ideas?
Thanks,
Alex
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: ATA failure regression in kernel 4.2
2015-07-23 17:48 ATA failure regression in kernel 4.2 Alex Deucher
@ 2015-07-23 18:35 ` Tejun Heo
2015-07-23 18:44 ` Alex Deucher
0 siblings, 1 reply; 15+ messages in thread
From: Tejun Heo @ 2015-07-23 18:35 UTC (permalink / raw)
To: Alex Deucher; +Cc: LKML
Hello,
On Thu, Jul 23, 2015 at 01:48:24PM -0400, Alex Deucher wrote:
> Something new in kernel 4.2 seems to have broken one of my hard drives
> (ssd) in kernel 4.2. 4.1 and older kernels work fine. Here are the
> relevant logs.
>
...
> [ 6.547628] ata2.00: qc timeout (cmd 0xec)
> [ 6.547721] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
> [ 7.007213] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
> [ 16.997819] ata2.00: qc timeout (cmd 0xec)
> [ 16.997910] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
> [ 16.997995] ata2: limiting SATA link speed to 3.0 Gbps
> [ 17.457400] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
> [ 47.429257] ata2.00: qc timeout (cmd 0xec)
> [ 47.429349] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
> [ 47.888822] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
Nothing really rings a bell. Timeouts on IDENTIFY. Could be IRQ
related. Which controller is it (lspci -nn)? Also, can you try to
bisect the issue?
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: ATA failure regression in kernel 4.2
2015-07-23 18:35 ` Tejun Heo
@ 2015-07-23 18:44 ` Alex Deucher
2015-07-24 17:38 ` Alex Deucher
0 siblings, 1 reply; 15+ messages in thread
From: Alex Deucher @ 2015-07-23 18:44 UTC (permalink / raw)
To: Tejun Heo; +Cc: LKML
On Thu, Jul 23, 2015 at 2:35 PM, Tejun Heo <tj@kernel.org> wrote:
> Hello,
>
> On Thu, Jul 23, 2015 at 01:48:24PM -0400, Alex Deucher wrote:
>> Something new in kernel 4.2 seems to have broken one of my hard drives
>> (ssd) in kernel 4.2. 4.1 and older kernels work fine. Here are the
>> relevant logs.
>>
> ...
>> [ 6.547628] ata2.00: qc timeout (cmd 0xec)
>> [ 6.547721] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>> [ 7.007213] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
>> [ 16.997819] ata2.00: qc timeout (cmd 0xec)
>> [ 16.997910] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>> [ 16.997995] ata2: limiting SATA link speed to 3.0 Gbps
>> [ 17.457400] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
>> [ 47.429257] ata2.00: qc timeout (cmd 0xec)
>> [ 47.429349] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>> [ 47.888822] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
>
> Nothing really rings a bell. Timeouts on IDENTIFY. Could be IRQ
> related. Which controller is it (lspci -nn)? Also, can you try to
> bisect the issue?
00:11.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD] FCH
SATA Controller [AHCI mode] [1022:7801] (rev 40)
00:14.1 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD] FCH
IDE Controller [1022:780c]
I can take a look at bisecting later this week.
Alex
>
> Thanks.
>
> --
> tejun
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: ATA failure regression in kernel 4.2
2015-07-23 18:44 ` Alex Deucher
@ 2015-07-24 17:38 ` Alex Deucher
2015-07-27 3:01 ` Jiang Liu
0 siblings, 1 reply; 15+ messages in thread
From: Alex Deucher @ 2015-07-24 17:38 UTC (permalink / raw)
To: Tejun Heo, Jiang Liu; +Cc: LKML
On Thu, Jul 23, 2015 at 2:44 PM, Alex Deucher <alexdeucher@gmail.com> wrote:
> On Thu, Jul 23, 2015 at 2:35 PM, Tejun Heo <tj@kernel.org> wrote:
>> Hello,
>>
>> On Thu, Jul 23, 2015 at 01:48:24PM -0400, Alex Deucher wrote:
>>> Something new in kernel 4.2 seems to have broken one of my hard drives
>>> (ssd) in kernel 4.2. 4.1 and older kernels work fine. Here are the
>>> relevant logs.
>>>
>> ...
>>> [ 6.547628] ata2.00: qc timeout (cmd 0xec)
>>> [ 6.547721] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>> [ 7.007213] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
>>> [ 16.997819] ata2.00: qc timeout (cmd 0xec)
>>> [ 16.997910] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>> [ 16.997995] ata2: limiting SATA link speed to 3.0 Gbps
>>> [ 17.457400] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
>>> [ 47.429257] ata2.00: qc timeout (cmd 0xec)
>>> [ 47.429349] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>> [ 47.888822] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
>>
>> Nothing really rings a bell. Timeouts on IDENTIFY. Could be IRQ
>> related. Which controller is it (lspci -nn)? Also, can you try to
>> bisect the issue?
>
> 00:11.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD] FCH
> SATA Controller [AHCI mode] [1022:7801] (rev 40)
> 00:14.1 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD] FCH
> IDE Controller [1022:780c]
>
> I can take a look at bisecting later this week.
You were right about the interrupts. This is an AMD Kaveri APU system.
52f518a3a7c2f80551a38d38be28bc9f335e713c is the first bad commit
commit 52f518a3a7c2f80551a38d38be28bc9f335e713c
Author: Jiang Liu <jiang.liu@linux.intel.com>
Date: Mon Apr 13 14:11:35 2015 +0800
x86/MSI: Use hierarchical irqdomains to manage MSI interrupts
Enhance MSI code to support hierarchical irqdomains, it helps to make
the architecture more clear.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: iommu@lists.linux-foundation.org
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Joerg Roedel <joro@8bytes.org>
Link: http://lkml.kernel.org/r/1428905519-23704-14-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
:040000 040000 786bcad9a3fad413e0b744e2cfa20da7ff402db6
22618cac66dee85a7752bb3af81169fff3a242d8 M arch
:040000 040000 acee54015803d4cd52d582a9e5e93aa56ad08482
40d2c7a02c0f8677e596c98c936404b2211336a3 M drivers
git bisect start
# bad: [3aa20508a6fe386c2a893027ef4c4ef78ee4eac2] Merge branch
'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
git bisect bad 3aa20508a6fe386c2a893027ef4c4ef78ee4eac2
# good: [b953c0d234bc72e8489d3bf51a276c5c4ec85345] Linux 4.1
git bisect good b953c0d234bc72e8489d3bf51a276c5c4ec85345
# bad: [0db9723cacf4d62bc3685fb15179b39ee4e17679] Merge branch 'next'
of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
git bisect bad 0db9723cacf4d62bc3685fb15179b39ee4e17679
# bad: [e3d8238d7f5c3f539a29f5ac596cd342d847e099] Merge tag
'arm64-upstream' of
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
git bisect bad e3d8238d7f5c3f539a29f5ac596cd342d847e099
# bad: [c70c5fb2b96dae0996fb0877d996458d3ca57eda] Merge tag
'pwm/for-4.2-rc1' of
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
git bisect bad c70c5fb2b96dae0996fb0877d996458d3ca57eda
# good: [e75c73ad64478c12b3a44b86a3e7f62a4f65b93e] Merge branch
'x86-fpu-for-linus' of
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
git bisect good e75c73ad64478c12b3a44b86a3e7f62a4f65b93e
# bad: [43224b96af3154cedd7220f7b90094905f07ac78] Merge branch
'timers-core-for-linus' of
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
git bisect bad 43224b96af3154cedd7220f7b90094905f07ac78
# bad: [9dda1658a9bd450d65da5153a2427955785d17c2] Merge branch
'x86/asm' into x86/core, to prepare for new patch
git bisect bad 9dda1658a9bd450d65da5153a2427955785d17c2
# bad: [191a66353b22fad8ac89404ab4c929cbe7b0afb2] Merge branch
'x86/asm' into x86/apic, to resolve a conflict
git bisect bad 191a66353b22fad8ac89404ab4c929cbe7b0afb2
# bad: [099c5c03487f6bca30c628e14e666788dd61fb33] irq_remapping/vt-d:
Move struct irq_2_iommu into intel_irq_remapping.c
git bisect bad 099c5c03487f6bca30c628e14e666788dd61fb33
# bad: [90d84fe95dd6b418383aa0e0e5cace8f1b1e7e30] x86/MSI: Replace
msi_update_msg() with irq_chip_compose_msi_msg()
git bisect bad 90d84fe95dd6b418383aa0e0e5cace8f1b1e7e30
# good: [3cb96f0c97330834929abe9bd2ca3c252a83def0] x86/hpet: Enhance
HPET IRQ to support hierarchical irqdomains
git bisect good 3cb96f0c97330834929abe9bd2ca3c252a83def0
# bad: [b1855c752e67d1125d41fadb499014b49a245db8] x86/MSI: Clean up
unused MSI related code and interfaces
git bisect bad b1855c752e67d1125d41fadb499014b49a245db8
# bad: [2b43817e481da9f5118adb56aef46b3f0298c685] irq_remapping/vt-d:
Clean up unused MSI related code
git bisect bad 2b43817e481da9f5118adb56aef46b3f0298c685
# bad: [80aa283364a17998dceb577bd185e3380b927544] x86/irq: Directly
call native_compose_msi_msg() for DMAR IRQ
git bisect bad 80aa283364a17998dceb577bd185e3380b927544
# bad: [52f518a3a7c2f80551a38d38be28bc9f335e713c] x86/MSI: Use
hierarchical irqdomains to manage MSI interrupts
git bisect bad 52f518a3a7c2f80551a38d38be28bc9f335e713c
# first bad commit: [52f518a3a7c2f80551a38d38be28bc9f335e713c]
x86/MSI: Use hierarchical irqdomains to manage MSI interrupts
lscpi:
00:00.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Device
[1022:1422]
00:00.2 IOMMU [0806]: Advanced Micro Devices, Inc. [AMD] Device [1022:1423]
00:01.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc.
[AMD/ATI] Kaveri [Radeon R7 200 Series] [1002:130f]
00:01.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI]
Device [1002:1308]
00:02.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Device
[1022:1424]
00:03.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Device
[1022:1424]
00:04.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Device
[1022:1424]
00:10.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH
USB XHCI Controller [1022:7814] (rev 09)
00:10.1 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH
USB XHCI Controller [1022:7814] (rev 09)
00:11.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD] FCH
SATA Controller [AHCI mode] [1022:7801] (rev 40)
00:12.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH
USB OHCI Controller [1022:7807] (rev 11)
00:12.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH
USB EHCI Controller [1022:7808] (rev 11)
00:13.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH
USB OHCI Controller [1022:7807] (rev 11)
00:13.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH
USB EHCI Controller [1022:7808] (rev 11)
00:14.0 SMBus [0c05]: Advanced Micro Devices, Inc. [AMD] FCH SMBus
Controller [1022:780b] (rev 16)
00:14.1 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD] FCH
IDE Controller [1022:780c]
00:14.2 Audio device [0403]: Advanced Micro Devices, Inc. [AMD] FCH
Azalia Controller [1022:780d] (rev 01)
00:14.3 ISA bridge [0601]: Advanced Micro Devices, Inc. [AMD] FCH LPC
Bridge [1022:780e] (rev 11)
00:14.4 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] FCH PCI
Bridge [1022:780f] (rev 40)
00:14.5 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH
USB OHCI Controller [1022:7809] (rev 11)
00:15.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] Hudson
PCI to PCI bridge (PCIE port 0) [1022:43a0]
00:15.2 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] Hudson
PCI to PCI bridge (PCIE port 2) [1022:43a2]
00:15.3 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] Hudson
PCI to PCI bridge (PCIE port 3) [1022:43a3]
00:18.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Device
[1022:141a]
00:18.1 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Device
[1022:141b]
00:18.2 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Device
[1022:141c]
00:18.3 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Device
[1022:141d]
00:18.4 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Device
[1022:141e]
00:18.5 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Device
[1022:141f]
03:00.0 USB controller [0c03]: ASMedia Technology Inc. ASM1042
SuperSpeed USB Host Controller [1b21:1042]
04:00.0 Ethernet controller [0200]: Qualcomm Atheros QCA8171 Gigabit
Ethernet [1969:10a1] (rev 10)
>
> Alex
>
>>
>> Thanks.
>>
>> --
>> tejun
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: ATA failure regression in kernel 4.2
2015-07-24 17:38 ` Alex Deucher
@ 2015-07-27 3:01 ` Jiang Liu
2015-07-27 15:21 ` Alex Deucher
0 siblings, 1 reply; 15+ messages in thread
From: Jiang Liu @ 2015-07-27 3:01 UTC (permalink / raw)
To: Alex Deucher, Tejun Heo; +Cc: LKML
On 2015/7/25 1:38, Alex Deucher wrote:
> On Thu, Jul 23, 2015 at 2:44 PM, Alex Deucher <alexdeucher@gmail.com> wrote:
>> On Thu, Jul 23, 2015 at 2:35 PM, Tejun Heo <tj@kernel.org> wrote:
>>> Hello,
>>>
>>> On Thu, Jul 23, 2015 at 01:48:24PM -0400, Alex Deucher wrote:
>>>> Something new in kernel 4.2 seems to have broken one of my hard drives
>>>> (ssd) in kernel 4.2. 4.1 and older kernels work fine. Here are the
>>>> relevant logs.
>>>>
>>> ...
>>>> [ 6.547628] ata2.00: qc timeout (cmd 0xec)
>>>> [ 6.547721] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>> [ 7.007213] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
>>>> [ 16.997819] ata2.00: qc timeout (cmd 0xec)
>>>> [ 16.997910] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>> [ 16.997995] ata2: limiting SATA link speed to 3.0 Gbps
>>>> [ 17.457400] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
>>>> [ 47.429257] ata2.00: qc timeout (cmd 0xec)
>>>> [ 47.429349] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>> [ 47.888822] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
>>>
>>> Nothing really rings a bell. Timeouts on IDENTIFY. Could be IRQ
>>> related. Which controller is it (lspci -nn)? Also, can you try to
>>> bisect the issue?
>>
>> 00:11.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD] FCH
>> SATA Controller [AHCI mode] [1022:7801] (rev 40)
>> 00:14.1 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD] FCH
>> IDE Controller [1022:780c]
>>
>> I can take a look at bisecting later this week.
>
> You were right about the interrupts. This is an AMD Kaveri APU system.
Hi Alex,
Could you please help to provide more information about the
system so we could identify the issue? Dmesg and /proc/interrupts
from good and bad kernels are welcomed.
Thanks!
Gerry
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: ATA failure regression in kernel 4.2
2015-07-27 3:01 ` Jiang Liu
@ 2015-07-27 15:21 ` Alex Deucher
2015-07-27 16:30 ` Jiang Liu
0 siblings, 1 reply; 15+ messages in thread
From: Alex Deucher @ 2015-07-27 15:21 UTC (permalink / raw)
To: Jiang Liu; +Cc: Tejun Heo, LKML
[-- Attachment #1: Type: text/plain, Size: 1996 bytes --]
On Sun, Jul 26, 2015 at 11:01 PM, Jiang Liu <jiang.liu@linux.intel.com> wrote:
> On 2015/7/25 1:38, Alex Deucher wrote:
>> On Thu, Jul 23, 2015 at 2:44 PM, Alex Deucher <alexdeucher@gmail.com> wrote:
>>> On Thu, Jul 23, 2015 at 2:35 PM, Tejun Heo <tj@kernel.org> wrote:
>>>> Hello,
>>>>
>>>> On Thu, Jul 23, 2015 at 01:48:24PM -0400, Alex Deucher wrote:
>>>>> Something new in kernel 4.2 seems to have broken one of my hard drives
>>>>> (ssd) in kernel 4.2. 4.1 and older kernels work fine. Here are the
>>>>> relevant logs.
>>>>>
>>>> ...
>>>>> [ 6.547628] ata2.00: qc timeout (cmd 0xec)
>>>>> [ 6.547721] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>>> [ 7.007213] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
>>>>> [ 16.997819] ata2.00: qc timeout (cmd 0xec)
>>>>> [ 16.997910] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>>> [ 16.997995] ata2: limiting SATA link speed to 3.0 Gbps
>>>>> [ 17.457400] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
>>>>> [ 47.429257] ata2.00: qc timeout (cmd 0xec)
>>>>> [ 47.429349] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>>> [ 47.888822] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
>>>>
>>>> Nothing really rings a bell. Timeouts on IDENTIFY. Could be IRQ
>>>> related. Which controller is it (lspci -nn)? Also, can you try to
>>>> bisect the issue?
>>>
>>> 00:11.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD] FCH
>>> SATA Controller [AHCI mode] [1022:7801] (rev 40)
>>> 00:14.1 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD] FCH
>>> IDE Controller [1022:780c]
>>>
>>> I can take a look at bisecting later this week.
>>
>> You were right about the interrupts. This is an AMD Kaveri APU system.
> Hi Alex,
> Could you please help to provide more information about the
> system so we could identify the issue? Dmesg and /proc/interrupts
> from good and bad kernels are welcomed.
> Thanks!
> Gerry
See attached. Thanks!
Alex
[-- Attachment #2: interrupts.working --]
[-- Type: application/octet-stream, Size: 3956 bytes --]
CPU0 CPU1 CPU2 CPU3
0: 134 0 0 0 IR-IO-APIC-edge timer
1: 1 1 2 6 IR-IO-APIC-edge i8042
7: 1 0 0 0 IR-IO-APIC-edge
8: 0 0 0 1 IR-IO-APIC-edge rtc0
9: 0 0 0 0 IR-IO-APIC-fasteoi acpi
14: 0 0 0 0 IR-IO-APIC-edge pata_atiixp
15: 0 0 0 0 IR-IO-APIC-edge pata_atiixp
16: 347 350 349 351 IR-IO-APIC 16-fasteoi snd_hda_intel
17: 0 0 0 0 IR-IO-APIC 17-fasteoi ehci_hcd:usb7, ehci_hcd:usb8
18: 0 0 0 0 IR-IO-APIC 18-fasteoi ohci_hcd:usb9, ohci_hcd:usb10, ohci_hcd:usb11
24: 0 0 0 0 IR-PCI-MSI-edge AMD-Vi
25: 0 0 0 0 IR-PCI-MSI-edge PCIe PME
26: 0 0 0 0 IR-PCI-MSI-edge PCIe PME
27: 0 0 0 0 IR-PCI-MSI-edge PCIe PME
28: 2760 14783 771 4431 IR-PCI-MSI-edge ahci0
29: 24669 24705 25636 30895 IR-PCI-MSI-edge ahci1
32: 2 1 1 18 IR-PCI-MSI-edge xhci_hcd
33: 0 0 0 0 IR-PCI-MSI-edge xhci_hcd
34: 0 0 0 0 IR-PCI-MSI-edge xhci_hcd
35: 0 0 0 0 IR-PCI-MSI-edge xhci_hcd
36: 0 0 0 0 IR-PCI-MSI-edge xhci_hcd
37: 0 0 0 0 IR-PCI-MSI-edge xhci_hcd
38: 0 0 0 0 IR-PCI-MSI-edge xhci_hcd
39: 0 0 0 0 IR-PCI-MSI-edge xhci_hcd
40: 0 0 0 0 IR-PCI-MSI-edge xhci_hcd
41: 0 0 0 0 IR-PCI-MSI-edge xhci_hcd
42: 0 0 0 0 IR-PCI-MSI-edge xhci_hcd
43: 0 0 0 0 IR-PCI-MSI-edge xhci_hcd
44: 0 0 0 0 IR-PCI-MSI-edge xhci_hcd
45: 0 0 0 0 IR-PCI-MSI-edge xhci_hcd
46: 0 0 0 0 IR-PCI-MSI-edge xhci_hcd
48: 1889 2074 1809 5879 IR-PCI-MSI-edge radeon
50: 47 46 45 53 IR-PCI-MSI-edge snd_hda_intel
51: 415107 23 23 55 IR-PCI-MSI-edge em1
NMI: 133 128 128 127 Non-maskable interrupts
LOC: 2545659 1614191 1845778 1618582 Local timer interrupts
SPU: 0 0 0 0 Spurious interrupts
PMI: 133 128 128 127 Performance monitoring interrupts
IWI: 0 1 1 1 IRQ work interrupts
RTR: 0 0 0 0 APIC ICR read retries
RES: 406735 292612 449749 264909 Rescheduling interrupts
CAL: 43331 43788 44073 40651 Function call interrupts
TLB: 1673 2167 2252 3620 TLB shootdowns
TRM: 0 0 0 0 Thermal event interrupts
THR: 0 0 0 0 Threshold APIC interrupts
MCE: 0 0 0 0 Machine check exceptions
MCP: 829 829 829 829 Machine check polls
HYP: 0 0 0 0 Hypervisor callback interrupts
ERR: 1
MIS: 0
[-- Attachment #3: interrupts.broken --]
[-- Type: application/octet-stream, Size: 4243 bytes --]
CPU0 CPU1 CPU2 CPU3
0: 136 0 0 0 IR-IO-APIC 2-edge timer
1: 2 2 1 84 IR-IO-APIC 1-edge i8042
7: 1 0 0 0 IR-IO-APIC 7-edge
8: 0 0 0 1 IR-IO-APIC 8-edge rtc0
9: 0 0 0 0 IR-IO-APIC 9-fasteoi acpi
14: 0 0 0 0 IR-IO-APIC 14-edge pata_atiixp
15: 0 0 0 0 IR-IO-APIC 15-edge pata_atiixp
16: 228 227 454 310 IR-IO-APIC 16-fasteoi snd_hda_intel
17: 0 0 0 0 IR-IO-APIC 17-fasteoi ehci_hcd:usb7, ehci_hcd:usb8
18: 0 0 0 0 IR-IO-APIC 18-fasteoi ohci_hcd:usb9, ohci_hcd:usb10, ohci_hcd:usb11
24: 0 0 0 0 PCI-MSI 4096-edge AMD-Vi
25: 0 0 0 0 IR-PCI-MSI 344064-edge PCIe PME
26: 0 0 0 0 IR-PCI-MSI 348160-edge PCIe PME
27: 0 0 0 0 IR-PCI-MSI 350208-edge PCIe PME
28: 267 248 823 3042 IR-PCI-MSI 278528-edge ahci0
29: 0 0 0 0 IR-PCI-MSI 278529-edge ahci1
32: 2 3 0 17 IR-PCI-MSI 262144-edge xhci_hcd
33: 0 0 0 0 IR-PCI-MSI 262145-edge xhci_hcd
34: 0 0 0 0 IR-PCI-MSI 262146-edge xhci_hcd
35: 0 0 0 0 IR-PCI-MSI 262147-edge xhci_hcd
36: 0 0 0 0 IR-PCI-MSI 262148-edge xhci_hcd
37: 0 0 0 0 IR-PCI-MSI 264192-edge xhci_hcd
38: 0 0 0 0 IR-PCI-MSI 264193-edge xhci_hcd
39: 0 0 0 0 IR-PCI-MSI 264194-edge xhci_hcd
40: 0 0 0 0 IR-PCI-MSI 264195-edge xhci_hcd
41: 0 0 0 0 IR-PCI-MSI 264196-edge xhci_hcd
42: 0 0 0 0 IR-PCI-MSI 1572864-edge xhci_hcd
43: 0 0 0 0 IR-PCI-MSI 1572865-edge xhci_hcd
44: 0 0 0 0 IR-PCI-MSI 1572866-edge xhci_hcd
45: 0 0 0 0 IR-PCI-MSI 1572867-edge xhci_hcd
46: 0 0 0 0 IR-PCI-MSI 1572868-edge xhci_hcd
48: 32 33 32 33 IR-PCI-MSI 18432-edge snd_hda_intel
NMI: 0 0 0 0 Non-maskable interrupts
LOC: 4744 4160 3670 4002 Local timer interrupts
SPU: 0 0 0 0 Spurious interrupts
PMI: 0 0 0 0 Performance monitoring interrupts
IWI: 0 0 0 1 IRQ work interrupts
RTR: 0 0 0 0 APIC ICR read retries
RES: 3365 2323 5560 2339 Rescheduling interrupts
CAL: 344 396 426 403 Function call interrupts
TLB: 28 22 39 386 TLB shootdowns
TRM: 0 0 0 0 Thermal event interrupts
THR: 0 0 0 0 Threshold APIC interrupts
DFR: 0 0 0 0 Deferred Error APIC interrupts
MCE: 0 0 0 0 Machine check exceptions
MCP: 3 3 3 3 Machine check polls
HYP: 0 0 0 0 Hypervisor callback interrupts
ERR: 1
MIS: 0
PIN: 0 0 0 0 Posted-interrupt notification event
PIW: 0 0 0 0 Posted-interrupt wakeup event
[-- Attachment #4: dmesg.working --]
[-- Type: application/octet-stream, Size: 63916 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.1.0-rc4+ (alex@cm) (gcc version 4.8.3 20140624 (Red Hat 4.8.3-1) (GCC) ) #747 SMP Wed Jun 3 17:17:51 EDT 2015
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.1.0-rc4+ root=/dev/mapper/fedora-root ro rd.lvm.lv=fedora/swap rd.md=0 rd.dm=0 vconsole.keymap=us rd.luks=0 vconsole.font=latarcyrheb-sun16 rd.lvm.lv=fedora/root rhgb quiet LANG=en_US.UTF-8
[ 0.000000] tseg: 007f800000
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009e7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009e800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007bc3afff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007bc3b000-0x000000007bc6afff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007bc6b000-0x000000007bf29fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007bf2a000-0x000000007bfe5fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007bfe6000-0x000000007e10afff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007e10b000-0x000000007e10bfff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007e10c000-0x000000007e311fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007e312000-0x000000007e467fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007e468000-0x000000007f02efff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007f02f000-0x000000007f071fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007f072000-0x000000007f7f0fff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007f7f1000-0x000000007f7fffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec01fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed40000-0x00000000fed44fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff800000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000043effffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: To Be Filled By O.E.M. To Be Filled By O.E.M./FM2A88X Extreme6+, BIOS P2.70 01/15/2014
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] e820: last_pfn = 0x43f000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF write-through
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-E7FFF uncachable
[ 0.000000] E8000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000000 mask FFFF80000000 write-back
[ 0.000000] 1 base 00007F800000 mask FFFFFF800000 uncachable
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 000000043f000000 aka 17392M
[ 0.000000] PAT configuration [0-7]: WB WC UC- UC WB WC UC- UC
[ 0.000000] e820: update [mem 0x7f800000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0x7f800 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000fd8a0-0x000fd8af] mapped at [ffff8800000fd8a0]
[ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x02015000, 0x02015fff] PGTABLE
[ 0.000000] BRK [0x02016000, 0x02016fff] PGTABLE
[ 0.000000] BRK [0x02017000, 0x02017fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x43ee00000-0x43effffff]
[ 0.000000] [mem 0x43ee00000-0x43effffff] page 2M
[ 0.000000] BRK [0x02018000, 0x02018fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x420000000-0x43edfffff]
[ 0.000000] [mem 0x420000000-0x43edfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x400000000-0x41fffffff]
[ 0.000000] [mem 0x400000000-0x41fffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x7bc3afff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x7bbfffff] page 2M
[ 0.000000] [mem 0x7bc00000-0x7bc3afff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x7bc6b000-0x7bf29fff]
[ 0.000000] [mem 0x7bc6b000-0x7bf29fff] page 4k
[ 0.000000] BRK [0x02019000, 0x02019fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x7e10b000-0x7e10bfff]
[ 0.000000] [mem 0x7e10b000-0x7e10bfff] page 4k
[ 0.000000] BRK [0x0201a000, 0x0201afff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x7e312000-0x7e467fff]
[ 0.000000] [mem 0x7e312000-0x7e467fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x7f02f000-0x7f071fff]
[ 0.000000] [mem 0x7f02f000-0x7f071fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x7f7f1000-0x7f7fffff]
[ 0.000000] [mem 0x7f7f1000-0x7f7fffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x3ffffffff]
[ 0.000000] [mem 0x100000000-0x3ffffffff] page 1G
[ 0.000000] RAMDISK: [mem 0x34924000-0x36489fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F04A0 000024 (v02 ALASKA)
[ 0.000000] ACPI: XSDT 0x000000007BFAE080 00007C (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 0x000000007BFB40E8 00010C (v05 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has zero address or length: 0x0000000000000000/0x1 (20150410/tbfadt-649)
[ 0.000000] ACPI: DSDT 0x000000007BFAE190 005F58 (v02 ALASKA A M I 00000000 INTL 20051117)
[ 0.000000] ACPI: FACS 0x000000007BFDC080 000040
[ 0.000000] ACPI: APIC 0x000000007BFB41F8 00007E (v03 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FPDT 0x000000007BFB4278 000044 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: MCFG 0x000000007BFB42C0 00003C (v01 ALASKA A M I 01072009 MSFT 00010013)
[ 0.000000] ACPI: HPET 0x000000007BFB4300 000038 (v01 ALASKA A M I 01072009 AMI 00000005)
[ 0.000000] ACPI: AAFT 0x000000007BFB4338 0002F5 (v01 ALASKA OEMAAFT 01072009 MSFT 00000097)
[ 0.000000] ACPI: IVRS 0x000000007BFB4630 000078 (v02 AMD BANTRY 00000001 AMD 00000000)
[ 0.000000] ACPI: SSDT 0x000000007BFB46A8 000B9C (v01 AMD BANTRY 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 0x000000007BFB5248 00033B (v02 AMD BANTRY 00000002 MSFT 04000000)
[ 0.000000] ACPI: CRAT 0x000000007BFB5588 0005A0 (v01 AMD BANTRY 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 0x000000007BFB5B28 001115 (v01 AMD CPMCMN 00000001 INTL 20051117)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000043effffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x43efe6000-0x43eff9fff]
[ 0.000000] [ffffea0000000000-ffffea0010ffffff] PMD -> [ffff88042f600000-ffff88043e5fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000043effffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009dfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x000000007bc3afff]
[ 0.000000] node 0: [mem 0x000000007bc6b000-0x000000007bf29fff]
[ 0.000000] node 0: [mem 0x000000007e10b000-0x000000007e10bfff]
[ 0.000000] node 0: [mem 0x000000007e312000-0x000000007e467fff]
[ 0.000000] node 0: [mem 0x000000007f02f000-0x000000007f071fff]
[ 0.000000] node 0: [mem 0x000000007f7f1000-0x000000007f7fffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000043effffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000043effffff]
[ 0.000000] On node 0 totalpages: 3911744
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3997 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7875 pages used for memmap
[ 0.000000] DMA32 zone: 503971 pages, LIFO batch:31
[ 0.000000] Normal zone: 53184 pages used for memmap
[ 0.000000] Normal zone: 3403776 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 5, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] IOAPIC[1]: apic_id 6, version 33, address 0xfec01000, GSI 24-55
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10228210 base: 0xfed00000
[ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009efff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7bc3b000-0x7bc6afff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7bf2a000-0x7bfe5fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7bfe6000-0x7e10afff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7e10c000-0x7e311fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7e468000-0x7f02efff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7f072000-0x7f7f0fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7f800000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec01fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec02000-0xfec0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec10000-0xfec10fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec11000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed01000-0xfed3ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed40000-0xfed44fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed45000-0xfed7ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed80000-0xfed8ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed90000-0xff7fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff800000-0xffffffff]
[ 0.000000] e820: [mem 0x7f800000-0xfebfffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 34 pages/cpu @ffff88043ec00000 s98968 r8192 d32104 u524288
[ 0.000000] pcpu-alloc: s98968 r8192 d32104 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 3850600
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.1.0-rc4+ root=/dev/mapper/fedora-root ro rd.lvm.lv=fedora/swap rd.md=0 rd.dm=0 vconsole.keymap=us rd.luks=0 vconsole.font=latarcyrheb-sun16 rd.lvm.lv=fedora/root rhgb quiet LANG=en_US.UTF-8
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340 using standard form
[ 0.000000] AGP: Checking aperture...
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] AGP: Node 0: aperture [bus addr 0x00000000-0x01ffffff] (32MB)
[ 0.000000] AGP: Your BIOS doesn't leave a aperture memory hole
[ 0.000000] AGP: Please enable the IOMMU option in the BIOS setup
[ 0.000000] AGP: This costs you 64MB of RAM
[ 0.000000] AGP: Mapping aperture over RAM [mem 0x70000000-0x73ffffff] (65536KB)
[ 0.000000] PM: Registered nosave memory: [mem 0x70000000-0x73ffffff]
[ 0.000000] Memory: 15224192K/15646976K available (7397K kernel code, 1190K rwdata, 3188K rodata, 1528K init, 1420K bss, 422784K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS:8448 nr_irqs:1000 16
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] clocksource hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 3693.379 MHz processor
[ 0.000023] Calibrating delay loop (skipped), value calculated using timer frequency.. 7386.75 BogoMIPS (lpj=3693379)
[ 0.000026] pid_max: default: 32768 minimum: 301
[ 0.000031] ACPI: Core revision 20150410
[ 0.003277] ACPI: All ACPI Tables successfully acquired
[ 0.011685] Security Framework initialized
[ 0.011698] SELinux: Initializing.
[ 0.011703] SELinux: Starting in permissive mode
[ 0.012729] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.017215] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.019194] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.019212] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.019507] Initializing cgroup subsys blkio
[ 0.019511] Initializing cgroup subsys devices
[ 0.019513] Initializing cgroup subsys freezer
[ 0.019515] Initializing cgroup subsys net_cls
[ 0.019517] Initializing cgroup subsys perf_event
[ 0.019536] CPU: Physical Processor ID: 0
[ 0.019537] CPU: Processor Core ID: 0
[ 0.019538] mce: CPU supports 7 MCE banks
[ 0.019544] LVT offset 1 assigned for vector 0xf9
[ 0.019549] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512
[ 0.019551] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0
[ 0.019660] Freeing SMP alternatives memory: 28K (ffffffff81ea9000 - ffffffff81eb0000)
[ 0.020445] ftrace: allocating 27659 entries in 109 pages
[ 0.110067] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.221251] smpboot: CPU0: AMD A10-7850K APU with Radeon(TM) R7 Graphics (fam: 15, model: 30, stepping: 01)
[ 0.221276] Performance Events: Fam15h core perfctr, AMD PMU driver.
[ 0.221280] ... version: 0
[ 0.221282] ... bit width: 48
[ 0.221282] ... generic registers: 6
[ 0.221283] ... value mask: 0000ffffffffffff
[ 0.221284] ... max period: 00007fffffffffff
[ 0.221285] ... fixed-purpose events: 0
[ 0.221286] ... event mask: 000000000000003f
[ 0.221866] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.221938] x86: Booting SMP configuration:
[ 0.221939] .... node #0, CPUs: #1 #2 #3
[ 0.261424] x86: Booted up 1 node, 4 CPUs
[ 0.261427] smpboot: Total of 4 processors activated (29547.03 BogoMIPS)
[ 0.262127] devtmpfs: initialized
[ 0.262399] PM: Registering ACPI NVS region [mem 0x7bf2a000-0x7bfe5fff] (770048 bytes)
[ 0.262411] PM: Registering ACPI NVS region [mem 0x7e10c000-0x7e311fff] (2121728 bytes)
[ 0.262508] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.262583] atomic64_test: passed for x86-64 platform with CX8 and with SSE
[ 0.262585] pinctrl core: initialized pinctrl subsystem
[ 0.262628] RTC time: 17:58:30, date: 07/24/15
[ 0.262733] NET: Registered protocol family 16
[ 0.267219] cpuidle: using governor ladder
[ 0.273212] cpuidle: using governor menu
[ 0.273334] ACPI: bus type PCI registered
[ 0.273336] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.273423] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.273426] PCI: not using MMCONFIG
[ 0.273427] PCI: Using configuration type 1 for base access
[ 0.273428] PCI: Using configuration type 1 for extended access
[ 0.279596] ACPI: Added _OSI(Module Device)
[ 0.279599] ACPI: Added _OSI(Processor Device)
[ 0.279601] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.279602] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.281598] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.284860] ACPI: Interpreter enabled
[ 0.284866] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20150410/hwxface-580)
[ 0.284870] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150410/hwxface-580)
[ 0.284886] ACPI: (supports S0 S3 S4 S5)
[ 0.284887] ACPI: Using IOAPIC for interrupt routing
[ 0.284906] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.284943] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[ 0.285310] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.290787] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.290794] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.291024] acpi PNP0A03:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[ 0.291331] PCI host bridge to bus 0000:00
[ 0.291333] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.291335] pci_bus 0000:00: root bus resource [io 0x0000-0x03af window]
[ 0.291337] pci_bus 0000:00: root bus resource [io 0x03e0-0x0cf7 window]
[ 0.291338] pci_bus 0000:00: root bus resource [io 0x03b0-0x03df window]
[ 0.291340] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.291341] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.291343] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[ 0.291344] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff window]
[ 0.291350] pci 0000:00:00.0: [1022:1422] type 00 class 0x060000
[ 0.291440] pci 0000:00:00.2: [1022:1423] type 00 class 0x080600
[ 0.291536] pci 0000:00:01.0: [1002:130f] type 00 class 0x030000
[ 0.291545] pci 0000:00:01.0: reg 0x10: [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.291551] pci 0000:00:01.0: reg 0x18: [mem 0xd0000000-0xd07fffff 64bit pref]
[ 0.291555] pci 0000:00:01.0: reg 0x20: [io 0xf000-0xf0ff]
[ 0.291560] pci 0000:00:01.0: reg 0x24: [mem 0xff700000-0xff73ffff]
[ 0.291564] pci 0000:00:01.0: reg 0x30: [mem 0xff740000-0xff75ffff pref]
[ 0.291585] pci 0000:00:01.0: supports D1 D2
[ 0.291587] pci 0000:00:01.0: PME# supported from D1 D2 D3hot
[ 0.291663] pci 0000:00:01.1: [1002:1308] type 00 class 0x040300
[ 0.291671] pci 0000:00:01.1: reg 0x10: [mem 0xff764000-0xff767fff 64bit]
[ 0.291702] pci 0000:00:01.1: supports D1 D2
[ 0.291768] pci 0000:00:02.0: [1022:1424] type 00 class 0x060000
[ 0.291849] pci 0000:00:03.0: [1022:1424] type 00 class 0x060000
[ 0.291940] pci 0000:00:04.0: [1022:1424] type 00 class 0x060000
[ 0.292041] pci 0000:00:10.0: [1022:7814] type 00 class 0x0c0330
[ 0.292060] pci 0000:00:10.0: reg 0x10: [mem 0xff76a000-0xff76bfff 64bit]
[ 0.292139] pci 0000:00:10.0: PME# supported from D0 D3hot D3cold
[ 0.292189] pci 0000:00:10.0: System wakeup disabled by ACPI
[ 0.292245] pci 0000:00:10.1: [1022:7814] type 00 class 0x0c0330
[ 0.292264] pci 0000:00:10.1: reg 0x10: [mem 0xff768000-0xff769fff 64bit]
[ 0.292343] pci 0000:00:10.1: PME# supported from D0 D3hot D3cold
[ 0.292390] pci 0000:00:10.1: System wakeup disabled by ACPI
[ 0.292433] pci 0000:00:11.0: [1022:7801] type 00 class 0x010601
[ 0.292446] pci 0000:00:11.0: reg 0x10: [io 0xf190-0xf197]
[ 0.292454] pci 0000:00:11.0: reg 0x14: [io 0xf180-0xf183]
[ 0.292461] pci 0000:00:11.0: reg 0x18: [io 0xf170-0xf177]
[ 0.292469] pci 0000:00:11.0: reg 0x1c: [io 0xf160-0xf163]
[ 0.292476] pci 0000:00:11.0: reg 0x20: [io 0xf150-0xf15f]
[ 0.292484] pci 0000:00:11.0: reg 0x24: [mem 0xff771000-0xff7717ff]
[ 0.292576] pci 0000:00:12.0: [1022:7807] type 00 class 0x0c0310
[ 0.292587] pci 0000:00:12.0: reg 0x10: [mem 0xff770000-0xff770fff]
[ 0.292668] pci 0000:00:12.0: System wakeup disabled by ACPI
[ 0.292704] pci 0000:00:12.2: [1022:7808] type 00 class 0x0c0320
[ 0.292717] pci 0000:00:12.2: reg 0x10: [mem 0xff76f000-0xff76f0ff]
[ 0.292776] pci 0000:00:12.2: supports D1 D2
[ 0.292778] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.292819] pci 0000:00:12.2: System wakeup disabled by ACPI
[ 0.292857] pci 0000:00:13.0: [1022:7807] type 00 class 0x0c0310
[ 0.292867] pci 0000:00:13.0: reg 0x10: [mem 0xff76e000-0xff76efff]
[ 0.292954] pci 0000:00:13.0: System wakeup disabled by ACPI
[ 0.292991] pci 0000:00:13.2: [1022:7808] type 00 class 0x0c0320
[ 0.293004] pci 0000:00:13.2: reg 0x10: [mem 0xff76d000-0xff76d0ff]
[ 0.293062] pci 0000:00:13.2: supports D1 D2
[ 0.293063] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.293103] pci 0000:00:13.2: System wakeup disabled by ACPI
[ 0.293141] pci 0000:00:14.0: [1022:780b] type 00 class 0x0c0500
[ 0.293264] pci 0000:00:14.1: [1022:780c] type 00 class 0x01018a
[ 0.293275] pci 0000:00:14.1: reg 0x10: [io 0xf140-0xf147]
[ 0.293282] pci 0000:00:14.1: reg 0x14: [io 0xf130-0xf133]
[ 0.293290] pci 0000:00:14.1: reg 0x18: [io 0xf120-0xf127]
[ 0.293297] pci 0000:00:14.1: reg 0x1c: [io 0xf110-0xf113]
[ 0.293304] pci 0000:00:14.1: reg 0x20: [io 0xf100-0xf10f]
[ 0.293321] pci 0000:00:14.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.293322] pci 0000:00:14.1: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.293323] pci 0000:00:14.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.293325] pci 0000:00:14.1: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.293395] pci 0000:00:14.2: [1022:780d] type 00 class 0x040300
[ 0.293411] pci 0000:00:14.2: reg 0x10: [mem 0xff760000-0xff763fff 64bit]
[ 0.293460] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[ 0.293500] pci 0000:00:14.2: System wakeup disabled by ACPI
[ 0.293532] pci 0000:00:14.3: [1022:780e] type 00 class 0x060100
[ 0.293648] pci 0000:00:14.4: [1022:780f] type 01 class 0x060401
[ 0.293711] pci 0000:00:14.4: System wakeup disabled by ACPI
[ 0.293744] pci 0000:00:14.5: [1022:7809] type 00 class 0x0c0310
[ 0.293755] pci 0000:00:14.5: reg 0x10: [mem 0xff76c000-0xff76cfff]
[ 0.293838] pci 0000:00:14.5: System wakeup disabled by ACPI
[ 0.293875] pci 0000:00:15.0: [1022:43a0] type 01 class 0x060400
[ 0.293931] pci 0000:00:15.0: supports D1 D2
[ 0.293932] pci 0000:00:15.0: PME# supported from D0 D3hot D3cold
[ 0.293974] pci 0000:00:15.0: System wakeup disabled by ACPI
[ 0.294011] pci 0000:00:15.2: [1022:43a2] type 01 class 0x060400
[ 0.294060] pci 0000:00:15.2: supports D1 D2
[ 0.294061] pci 0000:00:15.2: PME# supported from D0 D3hot D3cold
[ 0.294103] pci 0000:00:15.2: System wakeup disabled by ACPI
[ 0.294140] pci 0000:00:15.3: [1022:43a3] type 01 class 0x060400
[ 0.294191] pci 0000:00:15.3: supports D1 D2
[ 0.294192] pci 0000:00:15.3: PME# supported from D0 D3hot D3cold
[ 0.294242] pci 0000:00:15.3: System wakeup disabled by ACPI
[ 0.294282] pci 0000:00:18.0: [1022:141a] type 00 class 0x060000
[ 0.294349] pci 0000:00:18.1: [1022:141b] type 00 class 0x060000
[ 0.294415] pci 0000:00:18.2: [1022:141c] type 00 class 0x060000
[ 0.294481] pci 0000:00:18.3: [1022:141d] type 00 class 0x060000
[ 0.294549] pci 0000:00:18.4: [1022:141e] type 00 class 0x060000
[ 0.294614] pci 0000:00:18.5: [1022:141f] type 00 class 0x060000
[ 0.294749] pci 0000:00:14.4: PCI bridge to [bus 01] (subtractive decode)
[ 0.294756] pci 0000:00:14.4: bridge window [io 0x0000-0x03af window] (subtractive decode)
[ 0.294758] pci 0000:00:14.4: bridge window [io 0x03e0-0x0cf7 window] (subtractive decode)
[ 0.294759] pci 0000:00:14.4: bridge window [io 0x03b0-0x03df window] (subtractive decode)
[ 0.294761] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode)
[ 0.294762] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[ 0.294764] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000dffff window] (subtractive decode)
[ 0.294765] pci 0000:00:14.4: bridge window [mem 0xc0000000-0xffffffff window] (subtractive decode)
[ 0.294804] pci 0000:00:15.0: PCI bridge to [bus 02]
[ 0.294866] pci 0000:03:00.0: [1b21:1042] type 00 class 0x0c0330
[ 0.294891] pci 0000:03:00.0: reg 0x10: [mem 0xff600000-0xff607fff 64bit]
[ 0.295005] pci 0000:03:00.0: PME# supported from D3hot D3cold
[ 0.296193] pci 0000:00:15.2: PCI bridge to [bus 03]
[ 0.296203] pci 0000:00:15.2: bridge window [mem 0xff600000-0xff6fffff]
[ 0.296288] pci 0000:04:00.0: [1969:10a1] type 00 class 0x020000
[ 0.296315] pci 0000:04:00.0: reg 0x10: [mem 0xff500000-0xff53ffff 64bit]
[ 0.296326] pci 0000:04:00.0: reg 0x18: [io 0xe000-0xe07f]
[ 0.296429] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.298192] pci 0000:00:15.3: PCI bridge to [bus 04]
[ 0.298201] pci 0000:00:15.3: bridge window [io 0xe000-0xefff]
[ 0.298204] pci 0000:00:15.3: bridge window [mem 0xff500000-0xff5fffff]
[ 0.298754] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 7 10 *11 14 15)
[ 0.298817] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 5 7 10 *11 14 15)
[ 0.298880] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 7 *10 11 14 15)
[ 0.298947] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 *5 7 10 11 14 15)
[ 0.298998] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 10 11 14 15) *0
[ 0.299037] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 10 11 14 15) *0
[ 0.299075] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 5 7 10 11 14 15) *0
[ 0.299113] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 7 10 11 14 15) *0
[ 0.299411] vgaarb: setting as boot device: PCI:0000:00:01.0
[ 0.299414] vgaarb: device added: PCI:0000:00:01.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.299421] vgaarb: loaded
[ 0.299423] vgaarb: bridge control possible 0000:00:01.0
[ 0.299502] SCSI subsystem initialized
[ 0.299560] libata version 3.00 loaded.
[ 0.299590] ACPI: bus type USB registered
[ 0.299610] usbcore: registered new interface driver usbfs
[ 0.299619] usbcore: registered new interface driver hub
[ 0.299635] usbcore: registered new device driver usb
[ 0.299739] PCI: Using ACPI for IRQ routing
[ 0.306376] PCI: pci_cache_line_size set to 64 bytes
[ 0.306436] e820: reserve RAM buffer [mem 0x0009e800-0x0009ffff]
[ 0.306438] e820: reserve RAM buffer [mem 0x7bc3b000-0x7bffffff]
[ 0.306439] e820: reserve RAM buffer [mem 0x7bf2a000-0x7bffffff]
[ 0.306440] e820: reserve RAM buffer [mem 0x7e10c000-0x7fffffff]
[ 0.306441] e820: reserve RAM buffer [mem 0x7e468000-0x7fffffff]
[ 0.306442] e820: reserve RAM buffer [mem 0x7f072000-0x7fffffff]
[ 0.306444] e820: reserve RAM buffer [mem 0x7f800000-0x7fffffff]
[ 0.306445] e820: reserve RAM buffer [mem 0x43f000000-0x43fffffff]
[ 0.306558] NetLabel: Initializing
[ 0.306559] NetLabel: domain hash size = 128
[ 0.306560] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.306570] NetLabel: unlabeled traffic allowed by default
[ 0.306639] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.306641] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 0.308690] Switched to clocksource hpet
[ 0.316193] pnp: PnP ACPI init
[ 0.316316] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.316320] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.316394] system 00:01: [mem 0x80000000-0xbfffffff] has been reserved
[ 0.316396] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.316469] system 00:02: [mem 0xfeb80000-0xfebfffff] could not be reserved
[ 0.316472] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.316578] system 00:03: [io 0x0290-0x029f] has been reserved
[ 0.316580] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.316716] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.316753] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.316802] system 00:06: [io 0x04d0-0x04d1] has been reserved
[ 0.316804] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.316848] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.317045] pnp 00:08: [dma 0 disabled]
[ 0.317085] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.317338] system 00:09: [io 0x04d0-0x04d1] has been reserved
[ 0.317339] system 00:09: [io 0x040b] has been reserved
[ 0.317341] system 00:09: [io 0x04d6] has been reserved
[ 0.317343] system 00:09: [io 0x0c00-0x0c01] has been reserved
[ 0.317344] system 00:09: [io 0x0c14] has been reserved
[ 0.317346] system 00:09: [io 0x0c50-0x0c51] has been reserved
[ 0.317347] system 00:09: [io 0x0c52] has been reserved
[ 0.317348] system 00:09: [io 0x0c6c] has been reserved
[ 0.317350] system 00:09: [io 0x0c6f] has been reserved
[ 0.317351] system 00:09: [io 0x0cd0-0x0cd1] has been reserved
[ 0.317353] system 00:09: [io 0x0cd2-0x0cd3] has been reserved
[ 0.317354] system 00:09: [io 0x0cd4-0x0cd5] has been reserved
[ 0.317356] system 00:09: [io 0x0cd6-0x0cd7] has been reserved
[ 0.317357] system 00:09: [io 0x0cd8-0x0cdf] has been reserved
[ 0.317359] system 00:09: [io 0x0800-0x089f] could not be reserved
[ 0.317360] system 00:09: [io 0x0b20-0x0b3f] has been reserved
[ 0.317362] system 00:09: [io 0x0900-0x090f] has been reserved
[ 0.317363] system 00:09: [io 0x0910-0x091f] has been reserved
[ 0.317365] system 00:09: [io 0xfe00-0xfefe] has been reserved
[ 0.317367] system 00:09: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.317368] system 00:09: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.317370] system 00:09: [mem 0xfed80000-0xfed8ffff] has been reserved
[ 0.317372] system 00:09: [mem 0xfed61000-0xfed70fff] has been reserved
[ 0.317373] system 00:09: [mem 0xfec10000-0xfec10fff] has been reserved
[ 0.317375] system 00:09: [mem 0xfed00000-0xfed00fff] could not be reserved
[ 0.317377] system 00:09: [mem 0xff800000-0xffffffff] has been reserved
[ 0.317379] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.317545] pnp: PnP ACPI: found 10 devices
[ 0.324199] clocksource acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.324227] pci 0000:00:14.4: PCI bridge to [bus 01]
[ 0.324238] pci 0000:00:15.0: PCI bridge to [bus 02]
[ 0.324246] pci 0000:00:15.2: PCI bridge to [bus 03]
[ 0.324250] pci 0000:00:15.2: bridge window [mem 0xff600000-0xff6fffff]
[ 0.324255] pci 0000:00:15.3: PCI bridge to [bus 04]
[ 0.324258] pci 0000:00:15.3: bridge window [io 0xe000-0xefff]
[ 0.324261] pci 0000:00:15.3: bridge window [mem 0xff500000-0xff5fffff]
[ 0.324267] pci_bus 0000:00: resource 4 [io 0x0000-0x03af window]
[ 0.324269] pci_bus 0000:00: resource 5 [io 0x03e0-0x0cf7 window]
[ 0.324270] pci_bus 0000:00: resource 6 [io 0x03b0-0x03df window]
[ 0.324272] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff window]
[ 0.324273] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[ 0.324274] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[ 0.324276] pci_bus 0000:00: resource 10 [mem 0xc0000000-0xffffffff window]
[ 0.324277] pci_bus 0000:01: resource 4 [io 0x0000-0x03af window]
[ 0.324279] pci_bus 0000:01: resource 5 [io 0x03e0-0x0cf7 window]
[ 0.324280] pci_bus 0000:01: resource 6 [io 0x03b0-0x03df window]
[ 0.324281] pci_bus 0000:01: resource 7 [io 0x0d00-0xffff window]
[ 0.324283] pci_bus 0000:01: resource 8 [mem 0x000a0000-0x000bffff window]
[ 0.324284] pci_bus 0000:01: resource 9 [mem 0x000c0000-0x000dffff window]
[ 0.324285] pci_bus 0000:01: resource 10 [mem 0xc0000000-0xffffffff window]
[ 0.324287] pci_bus 0000:03: resource 1 [mem 0xff600000-0xff6fffff]
[ 0.324288] pci_bus 0000:04: resource 0 [io 0xe000-0xefff]
[ 0.324289] pci_bus 0000:04: resource 1 [mem 0xff500000-0xff5fffff]
[ 0.324320] NET: Registered protocol family 2
[ 0.324570] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.324876] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.325117] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.325172] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.325252] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.325372] NET: Registered protocol family 1
[ 0.325392] pci 0000:00:01.0: Video device with shadowed ROM
[ 0.563858] pci 0000:04:00.0: set MSI_INTX_DISABLE_BUG flag
[ 0.563864] PCI: CLS 64 bytes, default 64
[ 0.563920] Unpacking initramfs...
[ 0.933483] Freeing initrd memory: 28056K (ffff880034924000 - ffff88003648a000)
[ 0.933504] AMD-Vi: IOMMU performance counters supported
[ 0.933626] ERROR: Unable to locate IOAPIC for GSI 56
[ 0.933657] Failed to set pin attr for GSI56
[ 0.933660] pci 0000:00:00.2: PCI INT A: failed to register GSI
[ 0.934151] AMD-Vi: Found IOMMU at 0000:00:00.2 cap 0x40
[ 0.934153] AMD-Vi: Extended features: PPR GT IA PC
[ 0.934156] AMD-Vi: Interrupt remapping enabled
[ 0.935168] AMD-Vi: Using passthrough domain for device 0000:00:01.0
[ 0.947054] AMD-Vi: Lazy IO/TLB flushing enabled
[ 0.947503] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.947507] software IO TLB [mem 0x77c3b000-0x7bc3b000] (64MB) mapped at [ffff880077c3b000-ffff88007bc3afff]
[ 0.947600] perf: AMD NB counters detected
[ 0.947687] perf: amd_iommu: Detected. (2 banks, 4 counters/bank)
[ 0.947708] LVT offset 0 assigned for vector 0x400
[ 0.947721] perf: AMD IBS detected (0x000001ff)
[ 0.948173] AVX version of gcm_enc/dec engaged.
[ 0.948175] AES CTR mode by8 optimization enabled
[ 0.950341] alg: No test for __gcm-aes-aesni (__driver-gcm-aes-aesni)
[ 0.950747] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.950759] Initialise system trusted keyring
[ 0.950773] audit: initializing netlink subsys (disabled)
[ 0.950790] audit: type=2000 audit(1437760710.757:1): initialized
[ 0.951167] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.952893] VFS: Disk quotas dquot_6.6.0
[ 0.952924] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.953320] SELinux: Registering netfilter hooks
[ 0.954140] alg: No test for stdrng (krng)
[ 0.954150] NET: Registered protocol family 38
[ 0.954155] Key type asymmetric registered
[ 0.954157] Asymmetric key parser 'x509' registered
[ 0.954189] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.954224] io scheduler noop registered
[ 0.954226] io scheduler deadline registered
[ 0.954254] io scheduler cfq registered (default)
[ 0.954716] pcieport 0000:00:15.0: Signaling PME through PCIe PME interrupt
[ 0.954719] pcie_pme 0000:00:15.0:pcie01: service driver pcie_pme loaded
[ 0.954733] pcieport 0000:00:15.2: Signaling PME through PCIe PME interrupt
[ 0.954735] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
[ 0.954738] pcie_pme 0000:00:15.2:pcie01: service driver pcie_pme loaded
[ 0.954750] pcieport 0000:00:15.3: Signaling PME through PCIe PME interrupt
[ 0.954752] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt
[ 0.954755] pcie_pme 0000:00:15.3:pcie01: service driver pcie_pme loaded
[ 0.954765] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.954788] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.954875] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.954879] ACPI: Power Button [PWRB]
[ 0.954912] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.954914] ACPI: Power Button [PWRF]
[ 0.954953] ACPI: acpi_idle registered with cpuidle
[ 0.955419] GHES: HEST is not enabled!
[ 0.955519] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.976051] 00:08: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 0.976562] Non-volatile memory driver v1.3
[ 0.976593] Linux agpgart interface v0.103
[ 0.977919] loop: module loaded
[ 0.978015] ahci 0000:00:11.0: version 3.0
[ 0.978226] ahci 0000:00:11.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[ 0.978229] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck led clo pmp pio slum part sxs
[ 0.978569] scsi host0: ahci
[ 0.978668] scsi host1: ahci
[ 0.978707] ata1: SATA max UDMA/133 abar m2048@0xff771000 port 0xff771100 irq 28
[ 0.978709] ata2: SATA max UDMA/133 abar m2048@0xff771000 port 0xff771180 irq 29
[ 0.978789] libphy: Fixed MDIO Bus: probed
[ 0.978921] QUIRK: Enable AMD PLL fix
[ 0.978930] xhci_hcd 0000:00:10.0: xHCI Host Controller
[ 0.978965] xhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 0.979147] xhci_hcd 0000:00:10.0: hcc params 0x014040c3 hci version 0x100 quirks 0x00000418
[ 0.979295] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.979296] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.979298] usb usb1: Product: xHCI Host Controller
[ 0.979299] usb usb1: Manufacturer: Linux 4.1.0-rc4+ xhci-hcd
[ 0.979300] usb usb1: SerialNumber: 0000:00:10.0
[ 0.979399] hub 1-0:1.0: USB hub found
[ 0.979407] hub 1-0:1.0: 2 ports detected
[ 0.979490] xhci_hcd 0000:00:10.0: xHCI Host Controller
[ 0.979520] xhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[ 0.982577] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 0.982578] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.982579] usb usb2: Product: xHCI Host Controller
[ 0.982581] usb usb2: Manufacturer: Linux 4.1.0-rc4+ xhci-hcd
[ 0.982582] usb usb2: SerialNumber: 0000:00:10.0
[ 0.982665] hub 2-0:1.0: USB hub found
[ 0.982671] hub 2-0:1.0: 2 ports detected
[ 0.982822] xhci_hcd 0000:00:10.1: xHCI Host Controller
[ 0.982856] xhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 0.983031] xhci_hcd 0000:00:10.1: hcc params 0x014040c3 hci version 0x100 quirks 0x00000418
[ 0.983186] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.983188] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.983189] usb usb3: Product: xHCI Host Controller
[ 0.983190] usb usb3: Manufacturer: Linux 4.1.0-rc4+ xhci-hcd
[ 0.983191] usb usb3: SerialNumber: 0000:00:10.1
[ 0.983277] hub 3-0:1.0: USB hub found
[ 0.983285] hub 3-0:1.0: 2 ports detected
[ 0.983355] xhci_hcd 0000:00:10.1: xHCI Host Controller
[ 0.983391] xhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 4
[ 0.986461] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 0.986463] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.986464] usb usb4: Product: xHCI Host Controller
[ 0.986465] usb usb4: Manufacturer: Linux 4.1.0-rc4+ xhci-hcd
[ 0.986466] usb usb4: SerialNumber: 0000:00:10.1
[ 0.986544] hub 4-0:1.0: USB hub found
[ 0.986550] hub 4-0:1.0: 2 ports detected
[ 0.986657] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 0.986689] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 5
[ 1.045966] xhci_hcd 0000:03:00.0: hcc params 0x0200f180 hci version 0x96 quirks 0x00080000
[ 1.046106] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.046107] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.046108] usb usb5: Product: xHCI Host Controller
[ 1.046110] usb usb5: Manufacturer: Linux 4.1.0-rc4+ xhci-hcd
[ 1.046111] usb usb5: SerialNumber: 0000:03:00.0
[ 1.046190] hub 5-0:1.0: USB hub found
[ 1.046197] hub 5-0:1.0: 2 ports detected
[ 1.046266] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 1.046297] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 6
[ 1.046332] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.046334] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.046335] usb usb6: Product: xHCI Host Controller
[ 1.046336] usb usb6: Manufacturer: Linux 4.1.0-rc4+ xhci-hcd
[ 1.046337] usb usb6: SerialNumber: 0000:03:00.0
[ 1.046412] hub 6-0:1.0: USB hub found
[ 1.046419] hub 6-0:1.0: 2 ports detected
[ 1.046496] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.046500] ehci-pci: EHCI PCI platform driver
[ 1.046578] ehci-pci 0000:00:12.2: EHCI Host Controller
[ 1.046613] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 7
[ 1.046615] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.046623] ehci-pci 0000:00:12.2: debug port 1
[ 1.046653] ehci-pci 0000:00:12.2: irq 17, io mem 0xff76f000
[ 1.052113] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 1.052191] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.052193] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.052195] usb usb7: Product: EHCI Host Controller
[ 1.052196] usb usb7: Manufacturer: Linux 4.1.0-rc4+ ehci_hcd
[ 1.052197] usb usb7: SerialNumber: 0000:00:12.2
[ 1.052338] hub 7-0:1.0: USB hub found
[ 1.052346] hub 7-0:1.0: 5 ports detected
[ 1.052595] ehci-pci 0000:00:13.2: EHCI Host Controller
[ 1.052656] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 8
[ 1.052659] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.052668] ehci-pci 0000:00:13.2: debug port 1
[ 1.052697] ehci-pci 0000:00:13.2: irq 17, io mem 0xff76d000
[ 1.058107] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 1.058174] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.058176] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.058178] usb usb8: Product: EHCI Host Controller
[ 1.058180] usb usb8: Manufacturer: Linux 4.1.0-rc4+ ehci_hcd
[ 1.058181] usb usb8: SerialNumber: 0000:00:13.2
[ 1.058327] hub 8-0:1.0: USB hub found
[ 1.058333] hub 8-0:1.0: 5 ports detected
[ 1.058480] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.058487] ohci-pci: OHCI PCI platform driver
[ 1.058615] ohci-pci 0000:00:12.0: OHCI PCI host controller
[ 1.058677] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 9
[ 1.058716] ohci-pci 0000:00:12.0: irq 18, io mem 0xff770000
[ 1.113139] usb usb9: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.113143] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.113145] usb usb9: Product: OHCI PCI host controller
[ 1.113146] usb usb9: Manufacturer: Linux 4.1.0-rc4+ ohci_hcd
[ 1.113147] usb usb9: SerialNumber: 0000:00:12.0
[ 1.113308] hub 9-0:1.0: USB hub found
[ 1.113316] hub 9-0:1.0: 5 ports detected
[ 1.113565] ohci-pci 0000:00:13.0: OHCI PCI host controller
[ 1.113632] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 10
[ 1.113657] ohci-pci 0000:00:13.0: irq 18, io mem 0xff76e000
[ 1.168087] usb usb10: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.168092] usb usb10: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.168093] usb usb10: Product: OHCI PCI host controller
[ 1.168095] usb usb10: Manufacturer: Linux 4.1.0-rc4+ ohci_hcd
[ 1.168096] usb usb10: SerialNumber: 0000:00:13.0
[ 1.168261] hub 10-0:1.0: USB hub found
[ 1.168269] hub 10-0:1.0: 5 ports detected
[ 1.168513] ohci-pci 0000:00:14.5: OHCI PCI host controller
[ 1.168576] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 11
[ 1.168597] ohci-pci 0000:00:14.5: irq 18, io mem 0xff76c000
[ 1.223039] usb usb11: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.223043] usb usb11: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.223045] usb usb11: Product: OHCI PCI host controller
[ 1.223046] usb usb11: Manufacturer: Linux 4.1.0-rc4+ ohci_hcd
[ 1.223047] usb usb11: SerialNumber: 0000:00:14.5
[ 1.223204] hub 11-0:1.0: USB hub found
[ 1.223213] hub 11-0:1.0: 2 ports detected
[ 1.223326] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.223399] usbcore: registered new interface driver usbserial
[ 1.223407] usbcore: registered new interface driver usbserial_generic
[ 1.223413] usbserial: USB Serial support registered for generic
[ 1.223446] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 1.223447] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 1.223956] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.224059] mousedev: PS/2 mouse device common for all mice
[ 1.224347] rtc_cmos 00:05: RTC can wake from S4
[ 1.224463] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 1.224491] rtc_cmos 00:05: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.224545] device-mapper: uevent: version 1.0.3
[ 1.224617] device-mapper: ioctl: 4.31.0-ioctl (2015-3-12) initialised: dm-devel@redhat.com
[ 1.224819] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.224956] usbcore: registered new interface driver usbhid
[ 1.224957] usbhid: USB HID core driver
[ 1.224976] drop_monitor: Initializing network drop monitor service
[ 1.225038] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.225086] Initializing XFRM netlink socket
[ 1.225194] NET: Registered protocol family 10
[ 1.225412] mip6: Mobile IPv6
[ 1.225415] NET: Registered protocol family 17
[ 1.225904] Loading compiled-in X.509 certificates
[ 1.226621] Loaded X.509 cert 'Magrathea: Glacier signing key: 4a92f06a48b93d0e272e9a2b615aff0f01e0bbba'
[ 1.226632] registered taskstats version 1
[ 1.227004] Magic number: 7:57:998
[ 1.227035] system 00:00: hash matches
[ 1.227083] rtc_cmos 00:05: setting system clock to 2015-07-24 17:58:31 UTC (1437760711)
[ 1.227158] PM: Hibernation image not present or could not be loaded.
[ 1.256079] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[ 1.280936] usb 1-1: new low-speed USB device number 2 using xhci_hcd
[ 1.430351] usb 1-1: New USB device found, idVendor=046d, idProduct=c030
[ 1.430355] usb 1-1: New USB device strings: Mfr=4, Product=32, SerialNumber=0
[ 1.430357] usb 1-1: Product: iFeel Mouse
[ 1.430358] usb 1-1: Manufacturer: Logitech Inc.
[ 1.430673] usb 1-1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 1.430679] usb 1-1: ep 0x1 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 1.437784] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.437813] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.446606] input: Logitech Inc. iFeel Mouse as /devices/pci0000:00/0000:00:10.0/usb1/1-1/1-1:1.0/0003:046D:C030.0001/input/input3
[ 1.446844] hid-generic 0003:046D:C030.0001: input,hidraw0: USB HID v1.00 Mouse [Logitech Inc. iFeel Mouse ] on usb-0000:00:10.0-1/input0
[ 1.449778] ata2.00: ATA-8: KINGSTON SV300S37A120G, 506ABBF0, max UDMA/133
[ 1.449782] ata2.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.459721] ata2.00: configured for UDMA/133
[ 1.482155] ata1.00: HPA detected: current 156299375, native 156301488
[ 1.482161] ata1.00: ATA-7: ST380815AS, 4.AAB, max UDMA/133
[ 1.482162] ata1.00: 156299375 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.540410] ata1.00: configured for UDMA/133
[ 1.540587] scsi 0:0:0:0: Direct-Access ATA ST380815AS B PQ: 0 ANSI: 5
[ 1.540782] sd 0:0:0:0: [sda] 156299375 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 1.540816] sd 0:0:0:0: [sda] Write Protect is off
[ 1.540818] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.540832] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.540857] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.541021] scsi 1:0:0:0: Direct-Access ATA KINGSTON SV300S3 BBF0 PQ: 0 ANSI: 5
[ 1.541197] sd 1:0:0:0: [sdb] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 1.541239] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 1.541312] sd 1:0:0:0: [sdb] Write Protect is off
[ 1.541314] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.541348] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.543757] sdb: sdb1
[ 1.544139] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 1.588689] sda: sda1
[ 1.588942] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.589341] Freeing unused kernel memory: 1528K (ffffffff81d2b000 - ffffffff81ea9000)
[ 1.589343] Write protecting the kernel read-only data: 12288k
[ 1.589729] Freeing unused kernel memory: 784K (ffff88000173c000 - ffff880001800000)
[ 1.590034] Freeing unused kernel memory: 908K (ffff880001b1d000 - ffff880001c00000)
[ 1.592743] systemd[1]: systemd 204 running in system mode. (+PAM +LIBWRAP +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 1.592815] systemd[1]: Running in initial RAM disk.
[ 1.592895] systemd[1]: Set hostname to <cm>.
[ 1.593287] random: systemd urandom read with 17 bits of entropy available
[ 1.597641] systemd[1]: Expecting device dev-mapper-fedora\x2dswap.device...
[ 1.597652] systemd[1]: Expecting device dev-mapper-fedora\x2droot.device...
[ 1.597660] systemd[1]: Starting Timers.
[ 1.597669] systemd[1]: Reached target Timers.
[ 1.597693] systemd[1]: Starting Journal Socket.
[ 1.597735] systemd[1]: Listening on Journal Socket.
[ 1.597857] systemd[1]: Starting dracut cmdline hook...
[ 1.598248] systemd[1]: Starting Journal Service...
[ 1.598601] systemd[1]: Started Journal Service.
[ 1.599025] systemd[1]: Started Load Kernel Modules.
[ 1.599062] systemd[1]: Starting udev Kernel Socket.
[ 1.599086] systemd[1]: Listening on udev Kernel Socket.
[ 1.599134] systemd[1]: Starting udev Control Socket.
[ 1.599161] systemd[1]: Listening on udev Control Socket.
[ 1.599184] systemd[1]: Starting Sockets.
[ 1.599195] systemd[1]: Reached target Sockets.
[ 1.599220] systemd[1]: Starting Swap.
[ 1.599230] systemd[1]: Reached target Swap.
[ 1.599255] systemd[1]: Starting Local File Systems.
[ 1.599263] systemd[1]: Reached target Local File Systems.
[ 1.700813] systemd-udevd[187]: starting version 204
[ 1.742539] scsi host2: pata_atiixp
[ 1.742870] scsi host3: pata_atiixp
[ 1.742910] ata3: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf100 irq 14
[ 1.742912] ata4: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf108 irq 15
[ 1.798829] [drm] Initialized drm 1.1.0 20060810
[ 1.948245] tsc: Refined TSC clocksource calibration: 3693.283 MHz
[ 1.948250] clocksource tsc: mask: 0xffffffffffffffff max_cycles: 0x6a7918f751d, max_idle_ns: 881590915016 ns
[ 2.132483] [drm] radeon kernel modesetting enabled.
[ 2.133660] [drm] initializing kernel modesetting (KAVERI 0x1002:0x130F 0x1849:0x130F).
[ 2.133674] [drm] register mmio base: 0xFF700000
[ 2.133675] [drm] register mmio size: 262144
[ 2.133679] [drm] doorbell mmio base: 0xD0000000
[ 2.133680] [drm] doorbell mmio size: 8388608
[ 2.133730] ATOM BIOS: 113
[ 2.133776] radeon 0000:00:01.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used)
[ 2.133778] radeon 0000:00:01.0: GTT: 1024M 0x0000000040000000 - 0x000000007FFFFFFF
[ 2.133779] [drm] Detected VRAM RAM=1024M, BAR=256M
[ 2.133780] [drm] RAM width 128bits DDR
[ 2.133831] [TTM] Zone kernel: Available graphics memory: 7627748 kiB
[ 2.133832] [TTM] Zone dma32: Available graphics memory: 2097152 kiB
[ 2.133833] [TTM] Initializing pool allocator
[ 2.133837] [TTM] Initializing DMA pool allocator
[ 2.133857] [drm] radeon: 1024M of VRAM memory ready
[ 2.133858] [drm] radeon: 1024M of GTT memory ready.
[ 2.133874] [drm] Loading kaveri Microcode
[ 2.133999] [drm] Internal thermal controller without fan control
[ 2.135448] [drm] radeon: dpm initialized
[ 2.137127] [drm] Found VCE firmware/feedback version 40.2.2 / 15!
[ 2.137137] [drm] GART: num cpu pages 262144, num gpu pages 262144
[ 2.145997] [drm] PCIE GART of 1024M enabled (table at 0x0000000000324000).
[ 2.146136] radeon 0000:00:01.0: WB enabled
[ 2.146149] radeon 0000:00:01.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0xffff88042458ac00
[ 2.146152] radeon 0000:00:01.0: fence driver on ring 1 use gpu addr 0x0000000040000c04 and cpu addr 0xffff88042458ac04
[ 2.146154] radeon 0000:00:01.0: fence driver on ring 2 use gpu addr 0x0000000040000c08 and cpu addr 0xffff88042458ac08
[ 2.146157] radeon 0000:00:01.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0xffff88042458ac0c
[ 2.146158] radeon 0000:00:01.0: fence driver on ring 4 use gpu addr 0x0000000040000c10 and cpu addr 0xffff88042458ac10
[ 2.146518] radeon 0000:00:01.0: fence driver on ring 5 use gpu addr 0x0000000000076c98 and cpu addr 0xffffc90002036c98
[ 2.146659] radeon 0000:00:01.0: fence driver on ring 6 use gpu addr 0x0000000040000c18 and cpu addr 0xffff88042458ac18
[ 2.146661] radeon 0000:00:01.0: fence driver on ring 7 use gpu addr 0x0000000040000c1c and cpu addr 0xffff88042458ac1c
[ 2.146664] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 2.146665] [drm] Driver supports precise vblank timestamp query.
[ 2.146703] radeon 0000:00:01.0: radeon: using MSI.
[ 2.146724] [drm] radeon: irq initialized.
[ 2.149477] [drm] ring test on 0 succeeded in 3 usecs
[ 2.149560] [drm] ring test on 1 succeeded in 3 usecs
[ 2.149574] [drm] ring test on 2 succeeded in 2 usecs
[ 2.149651] [drm] ring test on 3 succeeded in 3 usecs
[ 2.149656] [drm] ring test on 4 succeeded in 3 usecs
[ 2.195657] [drm] ring test on 5 succeeded in 1 usecs
[ 2.215656] [drm] UVD initialized successfully.
[ 2.325643] [drm] ring test on 6 succeeded in 15 usecs
[ 2.325654] [drm] ring test on 7 succeeded in 4 usecs
[ 2.325655] [drm] VCE initialized successfully.
[ 2.327752] [drm] ib test on ring 0 succeeded in 0 usecs
[ 2.827555] [drm] ib test on ring 1 succeeded in 0 usecs
[ 2.947496] Switched to clocksource tsc
[ 3.328080] [drm] ib test on ring 2 succeeded in 0 usecs
[ 3.328145] [drm] ib test on ring 3 succeeded in 0 usecs
[ 3.328184] [drm] ib test on ring 4 succeeded in 0 usecs
[ 3.848567] [drm] ib test on ring 5 succeeded
[ 3.869283] [drm] ib test on ring 6 succeeded
[ 3.869821] [drm] ib test on ring 7 succeeded
[ 3.870553] [drm] Radeon Display Connectors
[ 3.870558] [drm] Connector 0:
[ 3.870559] [drm] DVI-D-1
[ 3.870560] [drm] HPD3
[ 3.870562] [drm] DDC: 0x6550 0x6550 0x6554 0x6554 0x6558 0x6558 0x655c 0x655c
[ 3.870563] [drm] Encoders:
[ 3.870564] [drm] DFP2: INTERNAL_UNIPHY2
[ 3.870565] [drm] Connector 1:
[ 3.870566] [drm] VGA-1
[ 3.870567] [drm] HPD1
[ 3.870569] [drm] DDC: 0x6530 0x6530 0x6534 0x6534 0x6538 0x6538 0x653c 0x653c
[ 3.870569] [drm] Encoders:
[ 3.870570] [drm] CRT1: INTERNAL_UNIPHY
[ 3.870571] [drm] CRT1: NUTMEG
[ 3.870572] [drm] Connector 2:
[ 3.870573] [drm] DP-1
[ 3.870574] [drm] HPD5
[ 3.870575] [drm] DDC: 0x6570 0x6570 0x6574 0x6574 0x6578 0x6578 0x657c 0x657c
[ 3.870576] [drm] Encoders:
[ 3.870577] [drm] DFP3: INTERNAL_UNIPHY1
[ 3.870578] [drm] Connector 3:
[ 3.870579] [drm] HDMI-A-1
[ 3.870579] [drm] HPD2
[ 3.870581] [drm] DDC: 0x6540 0x6540 0x6544 0x6544 0x6548 0x6548 0x654c 0x654c
[ 3.870582] [drm] Encoders:
[ 3.870583] [drm] DFP1: INTERNAL_UNIPHY3
[ 3.976732] [drm] fb mappable at 0xC0528000
[ 3.976736] [drm] vram apper at 0xC0000000
[ 3.976737] [drm] size 5242880
[ 3.976739] [drm] fb depth is 24
[ 3.976740] [drm] pitch is 5120
[ 3.976850] fbcon: radeondrmfb (fb0) is primary device
[ 4.042427] Console: switching to colour frame buffer device 160x64
[ 4.045198] radeon 0000:00:01.0: fb0: radeondrmfb frame buffer device
[ 4.045201] radeon 0000:00:01.0: registered panic notifier
[ 4.059607] [drm] Initialized radeon 2.43.0 20080528 for 0000:00:01.0 on minor 0
[ 4.409376] random: nonblocking pool is initialized
[ 4.559367] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[ 4.734659] systemd-journald[100]: Received SIGTERM
[ 5.626576] SELinux: Disabled at runtime.
[ 5.626598] SELinux: Unregistering netfilter hooks
[ 5.666789] audit: type=1404 audit(1437760715.943:2): selinux=0 auid=4294967295 ses=4294967295
[ 6.652117] LVM: Logical Volume autoactivation enabled.
[ 6.652123] LVM: Activation generator successfully completed.
[ 9.170614] systemd-udevd[385]: starting version 204
[ 9.460888] acpi-cpufreq: overriding BIOS provided _PSD data
[ 9.497444] MCE: In-kernel MCE decoding enabled.
[ 9.657773] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 9.657830] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb20
[ 10.212514] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 10.311492] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 10.311660] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input5
[ 10.623299] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 10.837189] EDAC MC: Ver: 3.0.0
[ 10.843761] AMD64 EDAC driver v3.4.0
[ 10.843885] EDAC amd64: DRAM ECC disabled.
[ 10.843892] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
(Note that use of the override may cause unknown side effects.)
[ 10.904408] microcode: CPU0: patch_level=0x06003104
[ 11.000641] input: HD-Audio Generic HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.1/sound/card0/input6
[ 11.000795] input: HD-Audio Generic HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.1/sound/card0/input7
[ 11.000891] input: HD-Audio Generic HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.1/sound/card0/input8
[ 11.001946] input: HD-Audio Generic HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.1/sound/card0/input9
[ 11.007880] snd_hda_codec_realtek hdaudioC1D0: ALC1150: SKU not ready 0x00000000
[ 11.008352] snd_hda_codec_realtek hdaudioC1D0: autoconfig for ALC1150: line_outs=3 (0x14/0x15/0x16/0x0/0x0) type:line
[ 11.008355] snd_hda_codec_realtek hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 11.008357] snd_hda_codec_realtek hdaudioC1D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 11.008360] snd_hda_codec_realtek hdaudioC1D0: mono: mono_out=0x0
[ 11.008362] snd_hda_codec_realtek hdaudioC1D0: dig-out=0x1e/0x0
[ 11.008363] snd_hda_codec_realtek hdaudioC1D0: inputs:
[ 11.008366] snd_hda_codec_realtek hdaudioC1D0: Front Mic=0x19
[ 11.008368] snd_hda_codec_realtek hdaudioC1D0: Rear Mic=0x18
[ 11.008370] snd_hda_codec_realtek hdaudioC1D0: Line=0x1a
[ 11.008658] EXT4-fs (dm-0): re-mounted. Opts: (null)
[ 11.023180] input: HD-Audio Generic Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input10
[ 11.023264] input: HD-Audio Generic Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input11
[ 11.023340] input: HD-Audio Generic Line as /devices/pci0000:00/0000:00:14.2/sound/card1/input12
[ 11.023414] input: HD-Audio Generic Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card1/input13
[ 11.023490] input: HD-Audio Generic Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card1/input14
[ 11.023564] input: HD-Audio Generic Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card1/input15
[ 11.023650] input: HD-Audio Generic Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card1/input16
[ 11.081681] microcode: CPU1: patch_level=0x06003104
[ 11.081702] microcode: CPU2: patch_level=0x06003104
[ 11.081728] microcode: CPU3: patch_level=0x06003104
[ 11.081845] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 11.096650] alg: No test for crc32 (crc32-pclmul)
[ 11.151640] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[ 11.207091] alx 0000:04:00.0 eth0: Qualcomm Atheros AR816x/AR817x Ethernet [bc:5f:f4:f8:24:b7]
[ 11.815471] alx 0000:04:00.0 em1: renamed from eth0
[ 11.823205] systemd-udevd[388]: renamed network interface eth0 to em1
[ 13.076763] systemd-journald[362]: Received request to flush runtime journal from PID 1
[ 13.717925] Adding 16703484k swap on /dev/mapper/fedora-swap. Priority:-1 extents:1 across:16703484k FS
[ 14.586184] audit: type=1305 audit(1437760724.870:3): audit_pid=464 old=0 auid=4294967295 ses=4294967295 res=1
[ 15.743154] [drm] amdgpu kernel modesetting enabled.
[ 16.129536] kvm: Nested Virtualization enabled
[ 16.129541] kvm: Nested Paging enabled
[ 18.544091] systemd-logind[496]: Watching system buttons on /dev/input/event1 (Power Button)
[ 18.544166] systemd-logind[496]: Watching system buttons on /dev/input/event5 (Video Bus)
[ 18.544229] systemd-logind[496]: Watching system buttons on /dev/input/event0 (Power Button)
[ 48.904413] tun: Universal TUN/TAP device driver, 1.6
[ 48.904417] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 49.360740] Bluetooth: Core ver 2.20
[ 49.360766] NET: Registered protocol family 31
[ 49.360768] Bluetooth: HCI device and connection manager initialized
[ 49.360773] Bluetooth: HCI socket layer initialized
[ 49.360777] Bluetooth: L2CAP socket layer initialized
[ 49.360784] Bluetooth: SCO socket layer initialized
[ 49.431239] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 49.431246] Bluetooth: BNEP filters: protocol multicast
[ 49.431254] Bluetooth: BNEP socket layer initialized
[ 49.781701] IPv6: ADDRCONF(NETDEV_UP): em1: link is not ready
[ 49.783284] alx 0000:04:00.0 em1: NIC Up: 1 Gbps Full
[ 49.783579] IPv6: ADDRCONF(NETDEV_CHANGE): em1: link becomes ready
[ 49.856584] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 50.441812] Ebtables v2.0 registered
[ 60.673732] Adjusting tsc more than 11% (2533388 vs 2521159)
[-- Attachment #5: dmesg.broken --]
[-- Type: application/octet-stream, Size: 58379 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.2.0-rc3+ (alex@cm) (gcc version 4.8.3 20140624 (Red Hat 4.8.3-1) (GCC) ) #774 SMP Thu Jul 23 11:28:59 EDT 2015
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.2.0-rc3+ root=/dev/mapper/fedora-root ro rd.lvm.lv=fedora/swap rd.md=0 rd.dm=0 vconsole.keymap=us rd.luks=0 vconsole.font=latarcyrheb-sun16 rd.lvm.lv=fedora/root LANG=en_US.UTF-8 modprobe.blacklist=amdgpu,radeon 3
[ 0.000000] tseg: 007f800000
[ 0.000000] x86/fpu: xstate_offset[2]: 0240, xstate_sizes[2]: 0100
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x01: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x02: 'SSE registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x04: 'AVX registers'
[ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 0x340 bytes, using 'standard' format.
[ 0.000000] x86/fpu: Using 'eager' FPU context switches.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009e7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009e800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007bc3afff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007bc3b000-0x000000007bc6afff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007bc6b000-0x000000007bf29fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007bf2a000-0x000000007bfe5fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007bfe6000-0x000000007e10afff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007e10b000-0x000000007e10bfff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007e10c000-0x000000007e311fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007e312000-0x000000007e467fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007e468000-0x000000007f02efff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007f02f000-0x000000007f071fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007f072000-0x000000007f7f0fff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007f7f1000-0x000000007f7fffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec01fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed40000-0x00000000fed44fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff800000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000043effffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: To Be Filled By O.E.M. To Be Filled By O.E.M./FM2A88X Extreme6+, BIOS P2.70 01/15/2014
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x43f000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF write-through
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-E7FFF uncachable
[ 0.000000] E8000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000000 mask FFFF80000000 write-back
[ 0.000000] 1 base 00007F800000 mask FFFFFF800000 uncachable
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 000000043f000000 aka 17392M
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WC UC- WT
[ 0.000000] e820: update [mem 0x7f800000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0x7f800 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000fd8a0-0x000fd8af] mapped at [ffff8800000fd8a0]
[ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x02019000, 0x02019fff] PGTABLE
[ 0.000000] BRK [0x0201a000, 0x0201afff] PGTABLE
[ 0.000000] BRK [0x0201b000, 0x0201bfff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x43ee00000-0x43effffff]
[ 0.000000] [mem 0x43ee00000-0x43effffff] page 2M
[ 0.000000] BRK [0x0201c000, 0x0201cfff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x420000000-0x43edfffff]
[ 0.000000] [mem 0x420000000-0x43edfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x400000000-0x41fffffff]
[ 0.000000] [mem 0x400000000-0x41fffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x7bc3afff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x7bbfffff] page 2M
[ 0.000000] [mem 0x7bc00000-0x7bc3afff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x7bc6b000-0x7bf29fff]
[ 0.000000] [mem 0x7bc6b000-0x7bf29fff] page 4k
[ 0.000000] BRK [0x0201d000, 0x0201dfff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x7e10b000-0x7e10bfff]
[ 0.000000] [mem 0x7e10b000-0x7e10bfff] page 4k
[ 0.000000] BRK [0x0201e000, 0x0201efff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x7e312000-0x7e467fff]
[ 0.000000] [mem 0x7e312000-0x7e467fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x7f02f000-0x7f071fff]
[ 0.000000] [mem 0x7f02f000-0x7f071fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x7f7f1000-0x7f7fffff]
[ 0.000000] [mem 0x7f7f1000-0x7f7fffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x3ffffffff]
[ 0.000000] [mem 0x100000000-0x3ffffffff] page 1G
[ 0.000000] RAMDISK: [mem 0x34a38000-0x36513fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F04A0 000024 (v02 ALASKA)
[ 0.000000] ACPI: XSDT 0x000000007BFAE080 00007C (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 0x000000007BFB40E8 00010C (v05 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has zero address or length: 0x0000000000000000/0x1 (20150619/tbfadt-654)
[ 0.000000] ACPI: DSDT 0x000000007BFAE190 005F58 (v02 ALASKA A M I 00000000 INTL 20051117)
[ 0.000000] ACPI: FACS 0x000000007BFDC080 000040
[ 0.000000] ACPI: APIC 0x000000007BFB41F8 00007E (v03 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FPDT 0x000000007BFB4278 000044 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: MCFG 0x000000007BFB42C0 00003C (v01 ALASKA A M I 01072009 MSFT 00010013)
[ 0.000000] ACPI: HPET 0x000000007BFB4300 000038 (v01 ALASKA A M I 01072009 AMI 00000005)
[ 0.000000] ACPI: AAFT 0x000000007BFB4338 0002F5 (v01 ALASKA OEMAAFT 01072009 MSFT 00000097)
[ 0.000000] ACPI: IVRS 0x000000007BFB4630 000078 (v02 AMD BANTRY 00000001 AMD 00000000)
[ 0.000000] ACPI: SSDT 0x000000007BFB46A8 000B9C (v01 AMD BANTRY 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 0x000000007BFB5248 00033B (v02 AMD BANTRY 00000002 MSFT 04000000)
[ 0.000000] ACPI: CRAT 0x000000007BFB5588 0005A0 (v01 AMD BANTRY 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 0x000000007BFB5B28 001115 (v01 AMD CPMCMN 00000001 INTL 20051117)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000043effffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x43efe6000-0x43eff9fff]
[ 0.000000] [ffffea0000000000-ffffea0010ffffff] PMD -> [ffff88042f600000-ffff88043e5fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000043effffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009dfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x000000007bc3afff]
[ 0.000000] node 0: [mem 0x000000007bc6b000-0x000000007bf29fff]
[ 0.000000] node 0: [mem 0x000000007e10b000-0x000000007e10bfff]
[ 0.000000] node 0: [mem 0x000000007e312000-0x000000007e467fff]
[ 0.000000] node 0: [mem 0x000000007f02f000-0x000000007f071fff]
[ 0.000000] node 0: [mem 0x000000007f7f1000-0x000000007f7fffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000043effffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000043effffff]
[ 0.000000] On node 0 totalpages: 3911744
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3997 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7875 pages used for memmap
[ 0.000000] DMA32 zone: 503971 pages, LIFO batch:31
[ 0.000000] Normal zone: 53184 pages used for memmap
[ 0.000000] Normal zone: 3403776 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 5, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] IOAPIC[1]: apic_id 6, version 33, address 0xfec01000, GSI 24-55
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10228210 base: 0xfed00000
[ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009efff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7bc3b000-0x7bc6afff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7bf2a000-0x7bfe5fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7bfe6000-0x7e10afff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7e10c000-0x7e311fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7e468000-0x7f02efff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7f072000-0x7f7f0fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7f800000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec01fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec02000-0xfec0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec10000-0xfec10fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec11000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed01000-0xfed3ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed40000-0xfed44fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed45000-0xfed7ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed80000-0xfed8ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed90000-0xff7fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff800000-0xffffffff]
[ 0.000000] e820: [mem 0x7f800000-0xfebfffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 33 pages/cpu @ffff88043ec00000 s95512 r8192 d31464 u524288
[ 0.000000] pcpu-alloc: s95512 r8192 d31464 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 3850600
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.2.0-rc3+ root=/dev/mapper/fedora-root ro rd.lvm.lv=fedora/swap rd.md=0 rd.dm=0 vconsole.keymap=us rd.luks=0 vconsole.font=latarcyrheb-sun16 rd.lvm.lv=fedora/root LANG=en_US.UTF-8 modprobe.blacklist=amdgpu,radeon 3
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Memory: 15290280K/15646976K available (7209K kernel code, 1204K rwdata, 3220K rodata, 1520K init, 1428K bss, 356696K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000] NR_IRQS:8448 nr_irqs:1000 16
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 3693.328 MHz processor
[ 0.000023] Calibrating delay loop (skipped), value calculated using timer frequency.. 7386.65 BogoMIPS (lpj=3693328)
[ 0.000183] pid_max: default: 32768 minimum: 301
[ 0.000266] ACPI: Core revision 20150619
[ 0.003532] ACPI: All ACPI Tables successfully acquired
[ 0.003679] Security Framework initialized
[ 0.003759] SELinux: Initializing.
[ 0.003843] SELinux: Starting in permissive mode
[ 0.004830] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.009306] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.011374] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.011475] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.011899] Initializing cgroup subsys blkio
[ 0.011984] Initializing cgroup subsys devices
[ 0.012067] Initializing cgroup subsys freezer
[ 0.012150] Initializing cgroup subsys net_cls
[ 0.012234] Initializing cgroup subsys perf_event
[ 0.012344] CPU: Physical Processor ID: 0
[ 0.012426] CPU: Processor Core ID: 0
[ 0.012508] mce: CPU supports 7 MCE banks
[ 0.012594] LVT offset 1 assigned for vector 0xf9
[ 0.012680] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512
[ 0.012762] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0
[ 0.012942] Freeing SMP alternatives memory: 28K (ffffffff81eab000 - ffffffff81eb2000)
[ 0.021604] ftrace: allocating 27834 entries in 109 pages
[ 0.110844] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.222094] smpboot: CPU0: AMD A10-7850K APU with Radeon(TM) R7 Graphics (fam: 15, model: 30, stepping: 01)
[ 0.224120] Performance Events: Fam15h core perfctr, AMD PMU driver.
[ 0.224284] ... version: 0
[ 0.224365] ... bit width: 48
[ 0.224446] ... generic registers: 6
[ 0.224527] ... value mask: 0000ffffffffffff
[ 0.224609] ... max period: 00007fffffffffff
[ 0.224691] ... fixed-purpose events: 0
[ 0.224772] ... event mask: 000000000000003f
[ 0.225391] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.225592] x86: Booting SMP configuration:
[ 0.225673] .... node #0, CPUs: #1 #2 #3
[ 0.235315] x86: Booted up 1 node, 4 CPUs
[ 0.235473] smpboot: Total of 4 processors activated (29546.62 BogoMIPS)
[ 0.236274] devtmpfs: initialized
[ 0.236578] PM: Registering ACPI NVS region [mem 0x7bf2a000-0x7bfe5fff] (770048 bytes)
[ 0.236720] PM: Registering ACPI NVS region [mem 0x7e10c000-0x7e311fff] (2121728 bytes)
[ 0.236937] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.237151] atomic64_test: passed for x86-64 platform with CX8 and with SSE
[ 0.237232] pinctrl core: initialized pinctrl subsystem
[ 0.237353] RTC time: 15:00:24, date: 07/27/15
[ 0.237533] NET: Registered protocol family 16
[ 0.240083] cpuidle: using governor ladder
[ 0.244086] cpuidle: using governor menu
[ 0.244288] ACPI: bus type PCI registered
[ 0.244371] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.244537] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.244675] PCI: not using MMCONFIG
[ 0.244757] PCI: Using configuration type 1 for base access
[ 0.244840] PCI: Using configuration type 1 for extended access
[ 0.248443] ACPI: Added _OSI(Module Device)
[ 0.248527] ACPI: Added _OSI(Processor Device)
[ 0.248606] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.248685] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.250047] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.252279] ACPI: Interpreter enabled
[ 0.252366] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20150619/hwxface-580)
[ 0.252554] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150619/hwxface-580)
[ 0.252751] ACPI: (supports S0 S3 S4 S5)
[ 0.252831] ACPI: Using IOAPIC for interrupt routing
[ 0.252933] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.253103] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[ 0.253258] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.257491] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.257582] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.257877] acpi PNP0A03:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[ 0.258259] PCI host bridge to bus 0000:00
[ 0.258342] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.258426] pci_bus 0000:00: root bus resource [io 0x0000-0x03af window]
[ 0.258510] pci_bus 0000:00: root bus resource [io 0x03e0-0x0cf7 window]
[ 0.258593] pci_bus 0000:00: root bus resource [io 0x03b0-0x03df window]
[ 0.258676] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.258759] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.258904] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[ 0.259042] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff window]
[ 0.259193] pci 0000:00:00.0: [1022:1422] type 00 class 0x060000
[ 0.259276] pci 0000:00:00.2: [1022:1423] type 00 class 0x080600
[ 0.259358] pci 0000:00:01.0: [1002:130f] type 00 class 0x030000
[ 0.259372] pci 0000:00:01.0: reg 0x10: [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.259378] pci 0000:00:01.0: reg 0x18: [mem 0xd0000000-0xd07fffff 64bit pref]
[ 0.259382] pci 0000:00:01.0: reg 0x20: [io 0xf000-0xf0ff]
[ 0.259386] pci 0000:00:01.0: reg 0x24: [mem 0xff700000-0xff73ffff]
[ 0.259390] pci 0000:00:01.0: reg 0x30: [mem 0xff740000-0xff75ffff pref]
[ 0.259405] pci 0000:00:01.0: supports D1 D2
[ 0.259407] pci 0000:00:01.0: PME# supported from D1 D2 D3hot
[ 0.259469] pci 0000:00:01.1: [1002:1308] type 00 class 0x040300
[ 0.259482] pci 0000:00:01.1: reg 0x10: [mem 0xff764000-0xff767fff 64bit]
[ 0.259507] pci 0000:00:01.1: supports D1 D2
[ 0.259559] pci 0000:00:02.0: [1022:1424] type 00 class 0x060000
[ 0.259626] pci 0000:00:03.0: [1022:1424] type 00 class 0x060000
[ 0.259695] pci 0000:00:04.0: [1022:1424] type 00 class 0x060000
[ 0.259784] pci 0000:00:10.0: [1022:7814] type 00 class 0x0c0330
[ 0.259817] pci 0000:00:10.0: reg 0x10: [mem 0xff76a000-0xff76bfff 64bit]
[ 0.259887] pci 0000:00:10.0: PME# supported from D0 D3hot D3cold
[ 0.259924] pci 0000:00:10.0: System wakeup disabled by ACPI
[ 0.260051] pci 0000:00:10.1: [1022:7814] type 00 class 0x0c0330
[ 0.260091] pci 0000:00:10.1: reg 0x10: [mem 0xff768000-0xff769fff 64bit]
[ 0.260155] pci 0000:00:10.1: PME# supported from D0 D3hot D3cold
[ 0.260194] pci 0000:00:10.1: System wakeup disabled by ACPI
[ 0.260317] pci 0000:00:11.0: [1022:7801] type 00 class 0x010601
[ 0.260338] pci 0000:00:11.0: reg 0x10: [io 0xf190-0xf197]
[ 0.260345] pci 0000:00:11.0: reg 0x14: [io 0xf180-0xf183]
[ 0.260352] pci 0000:00:11.0: reg 0x18: [io 0xf170-0xf177]
[ 0.260359] pci 0000:00:11.0: reg 0x1c: [io 0xf160-0xf163]
[ 0.260366] pci 0000:00:11.0: reg 0x20: [io 0xf150-0xf15f]
[ 0.260373] pci 0000:00:11.0: reg 0x24: [mem 0xff771000-0xff7717ff]
[ 0.260447] pci 0000:00:12.0: [1022:7807] type 00 class 0x0c0310
[ 0.260459] pci 0000:00:12.0: reg 0x10: [mem 0xff770000-0xff770fff]
[ 0.260526] pci 0000:00:12.0: System wakeup disabled by ACPI
[ 0.260643] pci 0000:00:12.2: [1022:7808] type 00 class 0x0c0320
[ 0.260663] pci 0000:00:12.2: reg 0x10: [mem 0xff76f000-0xff76f0ff]
[ 0.260714] pci 0000:00:12.2: supports D1 D2
[ 0.260715] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.260744] pci 0000:00:12.2: System wakeup disabled by ACPI
[ 0.260869] pci 0000:00:13.0: [1022:7807] type 00 class 0x0c0310
[ 0.260881] pci 0000:00:13.0: reg 0x10: [mem 0xff76e000-0xff76efff]
[ 0.260950] pci 0000:00:13.0: System wakeup disabled by ACPI
[ 0.261068] pci 0000:00:13.2: [1022:7808] type 00 class 0x0c0320
[ 0.261094] pci 0000:00:13.2: reg 0x10: [mem 0xff76d000-0xff76d0ff]
[ 0.261146] pci 0000:00:13.2: supports D1 D2
[ 0.261147] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.261178] pci 0000:00:13.2: System wakeup disabled by ACPI
[ 0.261298] pci 0000:00:14.0: [1022:780b] type 00 class 0x0c0500
[ 0.261395] pci 0000:00:14.1: [1022:780c] type 00 class 0x01018a
[ 0.261407] pci 0000:00:14.1: reg 0x10: [io 0xf140-0xf147]
[ 0.261414] pci 0000:00:14.1: reg 0x14: [io 0xf130-0xf133]
[ 0.261422] pci 0000:00:14.1: reg 0x18: [io 0xf120-0xf127]
[ 0.261429] pci 0000:00:14.1: reg 0x1c: [io 0xf110-0xf113]
[ 0.261436] pci 0000:00:14.1: reg 0x20: [io 0xf100-0xf10f]
[ 0.261452] pci 0000:00:14.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.261535] pci 0000:00:14.1: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.261618] pci 0000:00:14.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.261701] pci 0000:00:14.1: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.261851] pci 0000:00:14.2: [1022:780d] type 00 class 0x040300
[ 0.261872] pci 0000:00:14.2: reg 0x10: [mem 0xff760000-0xff763fff 64bit]
[ 0.261916] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[ 0.261946] pci 0000:00:14.2: System wakeup disabled by ACPI
[ 0.262061] pci 0000:00:14.3: [1022:780e] type 00 class 0x060100
[ 0.262182] pci 0000:00:14.4: [1022:780f] type 01 class 0x060401
[ 0.262237] pci 0000:00:14.4: System wakeup disabled by ACPI
[ 0.262350] pci 0000:00:14.5: [1022:7809] type 00 class 0x0c0310
[ 0.262362] pci 0000:00:14.5: reg 0x10: [mem 0xff76c000-0xff76cfff]
[ 0.262430] pci 0000:00:14.5: System wakeup disabled by ACPI
[ 0.262548] pci 0000:00:15.0: [1022:43a0] type 01 class 0x060400
[ 0.262596] pci 0000:00:15.0: supports D1 D2
[ 0.262598] pci 0000:00:15.0: PME# supported from D0 D3hot D3cold
[ 0.262631] pci 0000:00:15.0: System wakeup disabled by ACPI
[ 0.262748] pci 0000:00:15.2: [1022:43a2] type 01 class 0x060400
[ 0.262796] pci 0000:00:15.2: supports D1 D2
[ 0.262797] pci 0000:00:15.2: PME# supported from D0 D3hot D3cold
[ 0.262840] pci 0000:00:15.2: System wakeup disabled by ACPI
[ 0.262957] pci 0000:00:15.3: [1022:43a3] type 01 class 0x060400
[ 0.263005] pci 0000:00:15.3: supports D1 D2
[ 0.263007] pci 0000:00:15.3: PME# supported from D0 D3hot D3cold
[ 0.263038] pci 0000:00:15.3: System wakeup disabled by ACPI
[ 0.263168] pci 0000:00:18.0: [1022:141a] type 00 class 0x060000
[ 0.263226] pci 0000:00:18.1: [1022:141b] type 00 class 0x060000
[ 0.263279] pci 0000:00:18.2: [1022:141c] type 00 class 0x060000
[ 0.263333] pci 0000:00:18.3: [1022:141d] type 00 class 0x060000
[ 0.263389] pci 0000:00:18.4: [1022:141e] type 00 class 0x060000
[ 0.263442] pci 0000:00:18.5: [1022:141f] type 00 class 0x060000
[ 0.263565] pci 0000:00:14.4: PCI bridge to [bus 01] (subtractive decode)
[ 0.263655] pci 0000:00:14.4: bridge window [io 0x0000-0x03af window] (subtractive decode)
[ 0.263657] pci 0000:00:14.4: bridge window [io 0x03e0-0x0cf7 window] (subtractive decode)
[ 0.263658] pci 0000:00:14.4: bridge window [io 0x03b0-0x03df window] (subtractive decode)
[ 0.263660] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode)
[ 0.263661] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[ 0.263663] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000dffff window] (subtractive decode)
[ 0.263664] pci 0000:00:14.4: bridge window [mem 0xc0000000-0xffffffff window] (subtractive decode)
[ 0.263703] pci 0000:00:15.0: PCI bridge to [bus 02]
[ 0.263849] pci 0000:03:00.0: [1b21:1042] type 00 class 0x0c0330
[ 0.263889] pci 0000:03:00.0: reg 0x10: [mem 0xff600000-0xff607fff 64bit]
[ 0.263981] pci 0000:03:00.0: PME# supported from D3hot D3cold
[ 0.265074] pci 0000:00:15.2: PCI bridge to [bus 03]
[ 0.265166] pci 0000:00:15.2: bridge window [mem 0xff600000-0xff6fffff]
[ 0.265254] pci 0000:04:00.0: [1969:10a1] type 00 class 0x020000
[ 0.265301] pci 0000:04:00.0: reg 0x10: [mem 0xff500000-0xff53ffff 64bit]
[ 0.265312] pci 0000:04:00.0: reg 0x18: [io 0xe000-0xe07f]
[ 0.265393] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.267073] pci 0000:00:15.3: PCI bridge to [bus 04]
[ 0.267163] pci 0000:00:15.3: bridge window [io 0xe000-0xefff]
[ 0.267166] pci 0000:00:15.3: bridge window [mem 0xff500000-0xff5fffff]
[ 0.267613] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 7 10 *11 14 15)
[ 0.267981] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 5 7 10 *11 14 15)
[ 0.268353] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 7 *10 11 14 15)
[ 0.268711] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 *5 7 10 11 14 15)
[ 0.269069] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 10 11 14 15) *0
[ 0.269447] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 10 11 14 15) *0
[ 0.269826] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 5 7 10 11 14 15) *0
[ 0.270202] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 7 10 11 14 15) *0
[ 0.270795] vgaarb: setting as boot device: PCI:0000:00:01.0
[ 0.270880] vgaarb: device added: PCI:0000:00:01.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.271024] vgaarb: loaded
[ 0.271109] vgaarb: bridge control possible 0000:00:01.0
[ 0.271265] SCSI subsystem initialized
[ 0.271410] libata version 3.00 loaded.
[ 0.271442] ACPI: bus type USB registered
[ 0.271541] usbcore: registered new interface driver usbfs
[ 0.271629] usbcore: registered new interface driver hub
[ 0.271727] usbcore: registered new device driver usb
[ 0.271911] PCI: Using ACPI for IRQ routing
[ 0.278495] PCI: pci_cache_line_size set to 64 bytes
[ 0.278552] e820: reserve RAM buffer [mem 0x0009e800-0x0009ffff]
[ 0.278554] e820: reserve RAM buffer [mem 0x7bc3b000-0x7bffffff]
[ 0.278556] e820: reserve RAM buffer [mem 0x7bf2a000-0x7bffffff]
[ 0.278557] e820: reserve RAM buffer [mem 0x7e10c000-0x7fffffff]
[ 0.278558] e820: reserve RAM buffer [mem 0x7e468000-0x7fffffff]
[ 0.278559] e820: reserve RAM buffer [mem 0x7f072000-0x7fffffff]
[ 0.278560] e820: reserve RAM buffer [mem 0x7f800000-0x7fffffff]
[ 0.278560] e820: reserve RAM buffer [mem 0x43f000000-0x43fffffff]
[ 0.278670] NetLabel: Initializing
[ 0.278752] NetLabel: domain hash size = 128
[ 0.278839] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.278929] NetLabel: unlabeled traffic allowed by default
[ 0.279089] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.279278] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 0.281404] clocksource: Switched to clocksource hpet
[ 0.288350] pnp: PnP ACPI init
[ 0.288554] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.288639] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.288700] system 00:01: [mem 0x80000000-0xbfffffff] has been reserved
[ 0.288783] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.288839] system 00:02: [mem 0xfeb80000-0xfebfffff] could not be reserved
[ 0.288923] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.289007] system 00:03: [io 0x0290-0x029f] has been reserved
[ 0.289091] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.289185] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.289210] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.289254] system 00:06: [io 0x04d0-0x04d1] has been reserved
[ 0.289338] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.289370] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.289513] pnp 00:08: [dma 0 disabled]
[ 0.289549] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.289735] system 00:09: [io 0x04d0-0x04d1] has been reserved
[ 0.289818] system 00:09: [io 0x040b] has been reserved
[ 0.289900] system 00:09: [io 0x04d6] has been reserved
[ 0.289985] system 00:09: [io 0x0c00-0x0c01] has been reserved
[ 0.290068] system 00:09: [io 0x0c14] has been reserved
[ 0.290150] system 00:09: [io 0x0c50-0x0c51] has been reserved
[ 0.290232] system 00:09: [io 0x0c52] has been reserved
[ 0.290315] system 00:09: [io 0x0c6c] has been reserved
[ 0.290402] system 00:09: [io 0x0c6f] has been reserved
[ 0.290485] system 00:09: [io 0x0cd0-0x0cd1] has been reserved
[ 0.290568] system 00:09: [io 0x0cd2-0x0cd3] has been reserved
[ 0.290651] system 00:09: [io 0x0cd4-0x0cd5] has been reserved
[ 0.290733] system 00:09: [io 0x0cd6-0x0cd7] has been reserved
[ 0.290816] system 00:09: [io 0x0cd8-0x0cdf] has been reserved
[ 0.290899] system 00:09: [io 0x0800-0x089f] could not be reserved
[ 0.290981] system 00:09: [io 0x0b20-0x0b3f] has been reserved
[ 0.291064] system 00:09: [io 0x0900-0x090f] has been reserved
[ 0.291146] system 00:09: [io 0x0910-0x091f] has been reserved
[ 0.291229] system 00:09: [io 0xfe00-0xfefe] has been reserved
[ 0.291312] system 00:09: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.291399] system 00:09: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.291483] system 00:09: [mem 0xfed80000-0xfed8ffff] has been reserved
[ 0.291566] system 00:09: [mem 0xfed61000-0xfed70fff] has been reserved
[ 0.291649] system 00:09: [mem 0xfec10000-0xfec10fff] has been reserved
[ 0.291733] system 00:09: [mem 0xfed00000-0xfed00fff] could not be reserved
[ 0.291817] system 00:09: [mem 0xff800000-0xffffffff] has been reserved
[ 0.291901] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.292025] pnp: PnP ACPI: found 10 devices
[ 0.298633] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.298793] pci 0000:00:14.4: PCI bridge to [bus 01]
[ 0.298881] pci 0000:00:15.0: PCI bridge to [bus 02]
[ 0.298967] pci 0000:00:15.2: PCI bridge to [bus 03]
[ 0.299050] pci 0000:00:15.2: bridge window [mem 0xff600000-0xff6fffff]
[ 0.299134] pci 0000:00:15.3: PCI bridge to [bus 04]
[ 0.299215] pci 0000:00:15.3: bridge window [io 0xe000-0xefff]
[ 0.299297] pci 0000:00:15.3: bridge window [mem 0xff500000-0xff5fffff]
[ 0.299382] pci_bus 0000:00: resource 4 [io 0x0000-0x03af window]
[ 0.299383] pci_bus 0000:00: resource 5 [io 0x03e0-0x0cf7 window]
[ 0.299384] pci_bus 0000:00: resource 6 [io 0x03b0-0x03df window]
[ 0.299390] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff window]
[ 0.299392] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[ 0.299393] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[ 0.299394] pci_bus 0000:00: resource 10 [mem 0xc0000000-0xffffffff window]
[ 0.299396] pci_bus 0000:01: resource 4 [io 0x0000-0x03af window]
[ 0.299397] pci_bus 0000:01: resource 5 [io 0x03e0-0x0cf7 window]
[ 0.299398] pci_bus 0000:01: resource 6 [io 0x03b0-0x03df window]
[ 0.299400] pci_bus 0000:01: resource 7 [io 0x0d00-0xffff window]
[ 0.299401] pci_bus 0000:01: resource 8 [mem 0x000a0000-0x000bffff window]
[ 0.299402] pci_bus 0000:01: resource 9 [mem 0x000c0000-0x000dffff window]
[ 0.299404] pci_bus 0000:01: resource 10 [mem 0xc0000000-0xffffffff window]
[ 0.299405] pci_bus 0000:03: resource 1 [mem 0xff600000-0xff6fffff]
[ 0.299407] pci_bus 0000:04: resource 0 [io 0xe000-0xefff]
[ 0.299408] pci_bus 0000:04: resource 1 [mem 0xff500000-0xff5fffff]
[ 0.299437] NET: Registered protocol family 2
[ 0.299735] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.300153] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.300479] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.300611] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.300771] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.300973] NET: Registered protocol family 1
[ 0.301070] pci 0000:00:01.0: Video device with shadowed ROM
[ 0.539515] pci 0000:04:00.0: set MSI_INTX_DISABLE_BUG flag
[ 0.539606] PCI: CLS 64 bytes, default 64
[ 0.539675] Unpacking initramfs...
[ 0.887290] Freeing initrd memory: 27504K (ffff880034a38000 - ffff880036514000)
[ 0.887486] AMD-Vi: IOMMU performance counters supported
[ 0.887693] ERROR: Unable to locate IOAPIC for GSI 56
[ 0.887778] pci 0000:00:00.2: PCI INT A: failed to register GSI
[ 0.888670] iommu: Adding device 0000:00:00.0 to group 0
[ 0.889118] iommu: Adding device 0000:00:01.0 to group 1
[ 0.889216] iommu: Using direct mapping for device 0000:00:01.0
[ 0.889315] iommu: Adding device 0000:00:01.1 to group 1
[ 0.889696] iommu: Adding device 0000:00:02.0 to group 2
[ 0.890145] iommu: Adding device 0000:00:03.0 to group 3
[ 0.890564] iommu: Adding device 0000:00:04.0 to group 4
[ 0.891002] iommu: Adding device 0000:00:10.0 to group 5
[ 0.892908] iommu: Adding device 0000:00:10.1 to group 5
[ 0.893335] iommu: Adding device 0000:00:11.0 to group 6
[ 0.893770] iommu: Adding device 0000:00:12.0 to group 7
[ 0.893872] iommu: Adding device 0000:00:12.2 to group 7
[ 0.894299] iommu: Adding device 0000:00:13.0 to group 8
[ 0.894394] iommu: Adding device 0000:00:13.2 to group 8
[ 0.894825] iommu: Adding device 0000:00:14.0 to group 9
[ 0.894927] iommu: Adding device 0000:00:14.1 to group 9
[ 0.895023] iommu: Adding device 0000:00:14.2 to group 9
[ 0.895117] iommu: Adding device 0000:00:14.3 to group 9
[ 0.895532] iommu: Adding device 0000:00:14.4 to group 10
[ 0.895970] iommu: Adding device 0000:00:14.5 to group 11
[ 0.896404] iommu: Adding device 0000:00:15.0 to group 12
[ 0.896499] iommu: Adding device 0000:00:15.2 to group 12
[ 0.896593] iommu: Adding device 0000:00:15.3 to group 12
[ 0.897041] iommu: Adding device 0000:00:18.0 to group 13
[ 0.897135] iommu: Adding device 0000:00:18.1 to group 13
[ 0.897227] iommu: Adding device 0000:00:18.2 to group 13
[ 0.897320] iommu: Adding device 0000:00:18.3 to group 13
[ 0.897413] iommu: Adding device 0000:00:18.4 to group 13
[ 0.897507] iommu: Adding device 0000:00:18.5 to group 13
[ 0.897596] iommu: Adding device 0000:03:00.0 to group 12
[ 0.897688] iommu: Adding device 0000:04:00.0 to group 12
[ 0.897769] AMD-Vi: Found IOMMU at 0000:00:00.2 cap 0x40
[ 0.897854] AMD-Vi: Extended features: PPR GT IA PC
[ 0.898066] AMD-Vi: Interrupt remapping enabled
[ 0.898355] AMD-Vi: Lazy IO/TLB flushing enabled
[ 0.900478] perf: AMD NB counters detected
[ 0.900577] perf: amd_iommu: Detected. (2 banks, 4 counters/bank)
[ 0.900679] LVT offset 0 assigned for vector 0x400
[ 0.900768] perf: AMD IBS detected (0x000001ff)
[ 0.901411] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.901511] Initialise system trusted keyring
[ 0.901605] audit: initializing netlink subsys (disabled)
[ 0.901707] audit: type=2000 audit(1438009224.708:1): initialized
[ 0.902139] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.903775] VFS: Disk quotas dquot_6.6.0
[ 0.903894] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.904314] SELinux: Registering netfilter hooks
[ 0.907689] NET: Registered protocol family 38
[ 0.907780] Key type asymmetric registered
[ 0.907878] Asymmetric key parser 'x509' registered
[ 0.907977] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.908152] io scheduler noop registered
[ 0.908237] io scheduler deadline registered
[ 0.908346] io scheduler cfq registered (default)
[ 0.908877] pcieport 0000:00:15.0: Signaling PME through PCIe PME interrupt
[ 0.908968] pcie_pme 0000:00:15.0:pcie01: service driver pcie_pme loaded
[ 0.908986] pcieport 0000:00:15.2: Signaling PME through PCIe PME interrupt
[ 0.909070] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
[ 0.909155] pcie_pme 0000:00:15.2:pcie01: service driver pcie_pme loaded
[ 0.909171] pcieport 0000:00:15.3: Signaling PME through PCIe PME interrupt
[ 0.909254] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt
[ 0.909339] pcie_pme 0000:00:15.3:pcie01: service driver pcie_pme loaded
[ 0.909344] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.909434] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.909606] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.909745] ACPI: Power Button [PWRB]
[ 0.909869] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.910014] ACPI: Power Button [PWRF]
[ 0.910131] ACPI: acpi_idle registered with cpuidle
[ 0.910478] GHES: HEST is not enabled!
[ 0.910673] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.931299] 00:08: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 0.931968] Non-volatile memory driver v1.3
[ 0.932078] Linux agpgart interface v0.103
[ 0.933477] loop: module loaded
[ 0.933645] ahci 0000:00:11.0: version 3.0
[ 0.933821] ahci 0000:00:11.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[ 0.933967] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck led clo pmp pio slum part sxs
[ 0.934454] scsi host0: ahci
[ 0.934668] scsi host1: ahci
[ 0.934807] ata1: SATA max UDMA/133 abar m2048@0xff771000 port 0xff771100 irq 28
[ 0.934947] ata2: SATA max UDMA/133 abar m2048@0xff771000 port 0xff771180 irq 29
[ 0.935185] libphy: Fixed MDIO Bus: probed
[ 0.935452] QUIRK: Enable AMD PLL fix
[ 0.935470] xhci_hcd 0000:00:10.0: xHCI Host Controller
[ 0.935592] xhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 0.935913] xhci_hcd 0000:00:10.0: hcc params 0x014040c3 hci version 0x100 quirks 0x00000418
[ 0.936204] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.936289] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.936432] usb usb1: Product: xHCI Host Controller
[ 0.936522] usb usb1: Manufacturer: Linux 4.2.0-rc3+ xhci-hcd
[ 0.936605] usb usb1: SerialNumber: 0000:00:10.0
[ 0.936894] hub 1-0:1.0: USB hub found
[ 0.936981] hub 1-0:1.0: 2 ports detected
[ 0.937142] xhci_hcd 0000:00:10.0: xHCI Host Controller
[ 0.937256] xhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[ 0.939335] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 0.939419] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.939563] usb usb2: Product: xHCI Host Controller
[ 0.939644] usb usb2: Manufacturer: Linux 4.2.0-rc3+ xhci-hcd
[ 0.939727] usb usb2: SerialNumber: 0000:00:10.0
[ 0.939943] hub 2-0:1.0: USB hub found
[ 0.940030] hub 2-0:1.0: 2 ports detected
[ 0.940242] xhci_hcd 0000:00:10.1: xHCI Host Controller
[ 0.940365] xhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 0.940674] xhci_hcd 0000:00:10.1: hcc params 0x014040c3 hci version 0x100 quirks 0x00000418
[ 0.940953] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.941036] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.941173] usb usb3: Product: xHCI Host Controller
[ 0.941254] usb usb3: Manufacturer: Linux 4.2.0-rc3+ xhci-hcd
[ 0.941337] usb usb3: SerialNumber: 0000:00:10.1
[ 0.941611] hub 3-0:1.0: USB hub found
[ 0.941698] hub 3-0:1.0: 2 ports detected
[ 0.941856] xhci_hcd 0000:00:10.1: xHCI Host Controller
[ 0.941971] xhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 4
[ 0.944101] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 0.944184] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.944321] usb usb4: Product: xHCI Host Controller
[ 0.944403] usb usb4: Manufacturer: Linux 4.2.0-rc3+ xhci-hcd
[ 0.944491] usb usb4: SerialNumber: 0000:00:10.1
[ 0.944750] hub 4-0:1.0: USB hub found
[ 0.944845] hub 4-0:1.0: 2 ports detected
[ 0.945033] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 0.945151] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 5
[ 1.004564] xhci_hcd 0000:03:00.0: hcc params 0x0200f180 hci version 0x96 quirks 0x00080000
[ 1.004872] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.004954] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.005091] usb usb5: Product: xHCI Host Controller
[ 1.005174] usb usb5: Manufacturer: Linux 4.2.0-rc3+ xhci-hcd
[ 1.005257] usb usb5: SerialNumber: 0000:03:00.0
[ 1.005521] hub 5-0:1.0: USB hub found
[ 1.005608] hub 5-0:1.0: 2 ports detected
[ 1.005765] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 1.005883] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 6
[ 1.006051] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.006134] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.006272] usb usb6: Product: xHCI Host Controller
[ 1.006354] usb usb6: Manufacturer: Linux 4.2.0-rc3+ xhci-hcd
[ 1.006442] usb usb6: SerialNumber: 0000:03:00.0
[ 1.006703] hub 6-0:1.0: USB hub found
[ 1.006798] hub 6-0:1.0: 2 ports detected
[ 1.006955] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.007041] ehci-pci: EHCI PCI platform driver
[ 1.007205] ehci-pci 0000:00:12.2: EHCI Host Controller
[ 1.007425] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 7
[ 1.007566] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.007712] ehci-pci 0000:00:12.2: debug port 1
[ 1.007836] ehci-pci 0000:00:12.2: irq 17, io mem 0xff76f000
[ 1.013856] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 1.013997] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.014078] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.014211] usb usb7: Product: EHCI Host Controller
[ 1.014292] usb usb7: Manufacturer: Linux 4.2.0-rc3+ ehci_hcd
[ 1.014371] usb usb7: SerialNumber: 0000:00:12.2
[ 1.014673] hub 7-0:1.0: USB hub found
[ 1.014769] hub 7-0:1.0: 5 ports detected
[ 1.015082] ehci-pci 0000:00:13.2: EHCI Host Controller
[ 1.015216] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 8
[ 1.015352] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.015491] ehci-pci 0000:00:13.2: debug port 1
[ 1.015599] ehci-pci 0000:00:13.2: irq 17, io mem 0xff76d000
[ 1.020857] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 1.020997] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.021081] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.021218] usb usb8: Product: EHCI Host Controller
[ 1.021300] usb usb8: Manufacturer: Linux 4.2.0-rc3+ ehci_hcd
[ 1.023190] usb usb8: SerialNumber: 0000:00:13.2
[ 1.023507] hub 8-0:1.0: USB hub found
[ 1.023594] hub 8-0:1.0: 5 ports detected
[ 1.023818] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.023906] ohci-pci: OHCI PCI platform driver
[ 1.024100] ohci-pci 0000:00:12.0: OHCI PCI host controller
[ 1.024238] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 9
[ 1.024409] ohci-pci 0000:00:12.0: irq 18, io mem 0xff770000
[ 1.078854] usb usb9: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.078942] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.079081] usb usb9: Product: OHCI PCI host controller
[ 1.079164] usb usb9: Manufacturer: Linux 4.2.0-rc3+ ohci_hcd
[ 1.079247] usb usb9: SerialNumber: 0000:00:12.0
[ 1.079692] hub 9-0:1.0: USB hub found
[ 1.079782] hub 9-0:1.0: 5 ports detected
[ 1.080085] ohci-pci 0000:00:13.0: OHCI PCI host controller
[ 1.080270] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 10
[ 1.080425] ohci-pci 0000:00:13.0: irq 18, io mem 0xff76e000
[ 1.134801] usb usb10: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.134889] usb usb10: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.135029] usb usb10: Product: OHCI PCI host controller
[ 1.135111] usb usb10: Manufacturer: Linux 4.2.0-rc3+ ohci_hcd
[ 1.135194] usb usb10: SerialNumber: 0000:00:13.0
[ 1.135509] hub 10-0:1.0: USB hub found
[ 1.135599] hub 10-0:1.0: 5 ports detected
[ 1.135912] ohci-pci 0000:00:14.5: OHCI PCI host controller
[ 1.136051] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 11
[ 1.136212] ohci-pci 0000:00:14.5: irq 18, io mem 0xff76c000
[ 1.190747] usb usb11: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.190836] usb usb11: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.190976] usb usb11: Product: OHCI PCI host controller
[ 1.191058] usb usb11: Manufacturer: Linux 4.2.0-rc3+ ohci_hcd
[ 1.191141] usb usb11: SerialNumber: 0000:00:14.5
[ 1.191446] hub 11-0:1.0: USB hub found
[ 1.191536] hub 11-0:1.0: 2 ports detected
[ 1.191741] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.191901] usbcore: registered new interface driver usbserial
[ 1.191990] usbcore: registered new interface driver usbserial_generic
[ 1.192080] usbserial: USB Serial support registered for generic
[ 1.192206] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 1.192290] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 1.193136] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.193419] mousedev: PS/2 mouse device common for all mice
[ 1.193718] rtc_cmos 00:05: RTC can wake from S4
[ 1.193909] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 1.194014] rtc_cmos 00:05: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.194213] device-mapper: uevent: version 1.0.3
[ 1.194354] device-mapper: ioctl: 4.32.0-ioctl (2015-6-26) initialised: dm-devel@redhat.com
[ 1.194676] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.194867] usbcore: registered new interface driver usbhid
[ 1.194950] usbhid: USB HID core driver
[ 1.195049] drop_monitor: Initializing network drop monitor service
[ 1.195194] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.195318] Initializing XFRM netlink socket
[ 1.195488] NET: Registered protocol family 10
[ 1.195766] mip6: Mobile IPv6
[ 1.195851] NET: Registered protocol family 17
[ 1.196220] AVX version of gcm_enc/dec engaged.
[ 1.196299] AES CTR mode by8 optimization enabled
[ 1.218763] Loading compiled-in X.509 certificates
[ 1.219589] Loaded X.509 cert 'Magrathea: Glacier signing key: 4a92f06a48b93d0e272e9a2b615aff0f01e0bbba'
[ 1.219748] registered taskstats version 1
[ 1.220143] Magic number: 7:587:33
[ 1.220306] rtc_cmos 00:05: setting system clock to 2015-07-27 15:00:25 UTC (1438009225)
[ 1.220514] PM: Hibernation image not present or could not be loaded.
[ 1.225693] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[ 1.241619] usb 1-1: new low-speed USB device number 2 using xhci_hcd
[ 1.392193] usb 1-1: New USB device found, idVendor=046d, idProduct=c030
[ 1.392282] usb 1-1: New USB device strings: Mfr=4, Product=32, SerialNumber=0
[ 1.392435] usb 1-1: Product: iFeel Mouse
[ 1.392518] usb 1-1: Manufacturer: Logitech Inc.
[ 1.392914] usb 1-1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 1.393060] usb 1-1: ep 0x1 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 1.394509] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.395378] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.409460] input: Logitech Inc. iFeel Mouse as /devices/pci0000:00/0000:00:10.0/usb1/1-1/1-1:1.0/0003:046D:C030.0001/input/input3
[ 1.409804] hid-generic 0003:046D:C030.0001: input,hidraw0: USB HID v1.00 Mouse [Logitech Inc. iFeel Mouse ] on usb-0000:00:10.0-1/input0
[ 1.443583] ata1.00: HPA detected: current 156299375, native 156301488
[ 1.443673] ata1.00: ATA-7: ST380815AS, 4.AAB, max UDMA/133
[ 1.443755] ata1.00: 156299375 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.501845] ata1.00: configured for UDMA/133
[ 1.502168] scsi 0:0:0:0: Direct-Access ATA ST380815AS B PQ: 0 ANSI: 5
[ 1.502513] sd 0:0:0:0: [sda] 156299375 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 1.502553] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.502848] sd 0:0:0:0: [sda] Write Protect is off
[ 1.502933] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.502965] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.550121] sda: sda1
[ 1.550562] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.902013] tsc: Refined TSC clocksource calibration: 3693.281 MHz
[ 1.902109] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x6a791632c9c, max_idle_ns: 881591001453 ns
[ 2.901315] clocksource: Switched to clocksource tsc
[ 6.389799] ata2.00: qc timeout (cmd 0xec)
[ 6.389897] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 6.849380] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 16.839988] ata2.00: qc timeout (cmd 0xec)
[ 16.840081] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 16.840165] ata2: limiting SATA link speed to 3.0 Gbps
[ 17.299559] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 47.271389] ata2.00: qc timeout (cmd 0xec)
[ 47.271481] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 47.730968] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 47.731546] Freeing unused kernel memory: 1520K (ffffffff81d2f000 - ffffffff81eab000)
[ 47.731689] Write protecting the kernel read-only data: 12288k
[ 47.732189] Freeing unused kernel memory: 972K (ffff88000170d000 - ffff880001800000)
[ 47.732586] Freeing unused kernel memory: 876K (ffff880001b25000 - ffff880001c00000)
[ 47.735329] systemd[1]: systemd 204 running in system mode. (+PAM +LIBWRAP +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 47.735546] systemd[1]: Running in initial RAM disk.
[ 47.736072] systemd[1]: Set hostname to <cm>.
[ 47.736525] random: systemd urandom read with 19 bits of entropy available
[ 47.740694] systemd[1]: Expecting device dev-mapper-fedora\x2dswap.device...
[ 47.741002] systemd[1]: Expecting device dev-mapper-fedora\x2droot.device...
[ 47.741261] systemd[1]: Starting Timers.
[ 47.741585] systemd[1]: Reached target Timers.
[ 47.741687] systemd[1]: Starting Journal Socket.
[ 47.742049] systemd[1]: Listening on Journal Socket.
[ 47.742240] systemd[1]: Starting dracut cmdline hook...
[ 47.742918] systemd[1]: Starting Journal Service...
[ 47.743803] systemd[1]: Started Journal Service.
[ 47.744124] systemd[1]: Started Load Kernel Modules.
[ 47.744236] systemd[1]: Starting udev Kernel Socket.
[ 47.744571] systemd[1]: Listening on udev Kernel Socket.
[ 47.744694] systemd[1]: Starting udev Control Socket.
[ 47.745033] systemd[1]: Listening on udev Control Socket.
[ 47.745134] systemd[1]: Starting Sockets.
[ 47.745457] systemd[1]: Reached target Sockets.
[ 47.745558] systemd[1]: Starting Swap.
[ 47.745911] systemd[1]: Reached target Swap.
[ 47.746013] systemd[1]: Starting Local File Systems.
[ 47.746334] systemd[1]: Reached target Local File Systems.
[ 47.840864] systemd-udevd[222]: starting version 204
[ 47.875474] scsi host2: pata_atiixp
[ 47.879456] scsi host3: pata_atiixp
[ 47.879615] ata3: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf100 irq 14
[ 47.879718] ata4: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf108 irq 15
[ 48.769060] random: nonblocking pool is initialized
[ 48.877312] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[ 49.042097] systemd-journald[134]: Received SIGTERM
[ 49.936322] SELinux: Disabled at runtime.
[ 49.936423] SELinux: Unregistering netfilter hooks
[ 49.979842] audit: type=1404 audit(1438009274.304:2): selinux=0 auid=4294967295 ses=4294967295
[ 50.953602] LVM: Logical Volume autoactivation enabled.
[ 50.953608] LVM: Activation generator successfully completed.
[ 53.457547] systemd-udevd[420]: starting version 204
[ 53.734632] EXT4-fs (dm-0): re-mounted. Opts: (null)
[ 54.381572] acpi-cpufreq: overriding BIOS provided _PSD data
[ 54.897161] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 54.897382] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb20
[ 55.326099] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 55.326387] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input4
[ 55.437665] microcode: CPU0: patch_level=0x06003104
[ 55.557913] microcode: CPU1: patch_level=0x06003104
[ 55.558044] microcode: CPU2: patch_level=0x06003104
[ 55.558153] microcode: CPU3: patch_level=0x06003104
[ 55.558354] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 56.272490] MCE: In-kernel MCE decoding enabled.
[ 56.322274] EDAC MC: Ver: 3.0.0
[ 56.356270] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 56.441181] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 56.545090] AMD64 EDAC driver v3.4.0
[ 56.545211] EDAC amd64: DRAM ECC disabled.
[ 56.545299] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
(Note that use of the override may cause unknown side effects.)
[ 57.432213] alx 0000:04:00.0 eth0: Qualcomm Atheros AR816x/AR817x Ethernet [bc:5f:f4:f8:24:b7]
[ 57.753091] Adding 16703484k swap on /dev/mapper/fedora-swap. Priority:-1 extents:1 across:16703484k FS
[ 58.091660] snd_hda_intel 0000:00:01.1: Force to non-snoop mode
[ 58.327839] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.1/sound/card0/input6
[ 58.328271] input: HDA ATI HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.1/sound/card0/input7
[ 58.328632] input: HDA ATI HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.1/sound/card0/input8
[ 58.328979] input: HDA ATI HDMI HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.1/sound/card0/input9
[ 58.429362] alx 0000:04:00.0 em1: renamed from eth0
[ 58.439083] systemd-udevd[435]: renamed network interface eth0 to em1
[ 58.642325] snd_hda_codec_realtek hdaudioC1D0: ALC1150: SKU not ready 0x00000000
[ 58.642965] snd_hda_codec_realtek hdaudioC1D0: autoconfig for ALC1150: line_outs=3 (0x14/0x15/0x16/0x0/0x0) type:line
[ 58.643105] snd_hda_codec_realtek hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 58.643242] snd_hda_codec_realtek hdaudioC1D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 58.643381] snd_hda_codec_realtek hdaudioC1D0: mono: mono_out=0x0
[ 58.643464] snd_hda_codec_realtek hdaudioC1D0: dig-out=0x1e/0x0
[ 58.643547] snd_hda_codec_realtek hdaudioC1D0: inputs:
[ 58.643648] snd_hda_codec_realtek hdaudioC1D0: Front Mic=0x19
[ 58.643732] snd_hda_codec_realtek hdaudioC1D0: Rear Mic=0x18
[ 58.643814] snd_hda_codec_realtek hdaudioC1D0: Line=0x1a
[ 58.660907] input: HD-Audio Generic Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input10
[ 58.661143] input: HD-Audio Generic Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input11
[ 58.661390] input: HD-Audio Generic Line as /devices/pci0000:00/0000:00:14.2/sound/card1/input12
[ 58.661600] input: HD-Audio Generic Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card1/input13
[ 58.661812] input: HD-Audio Generic Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card1/input14
[ 58.662007] input: HD-Audio Generic Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card1/input15
[ 58.662211] input: HD-Audio Generic Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card1/input16
[ 59.118915] kvm: Nested Virtualization enabled
[ 59.119007] kvm: Nested Paging enabled
[ 141.999303] systemd-journald[401]: Received request to flush runtime journal from PID 1
[ 142.466664] audit: type=1305 audit(1438009366.877:3): audit_pid=494 old=0 auid=4294967295 ses=4294967295 res=1
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: ATA failure regression in kernel 4.2
2015-07-27 15:21 ` Alex Deucher
@ 2015-07-27 16:30 ` Jiang Liu
2015-07-27 17:36 ` Alex Deucher
2015-07-28 18:19 ` Alex Deucher
0 siblings, 2 replies; 15+ messages in thread
From: Jiang Liu @ 2015-07-27 16:30 UTC (permalink / raw)
To: Alex Deucher; +Cc: Tejun Heo, LKML
On 2015/7/27 23:21, Alex Deucher wrote:
> On Sun, Jul 26, 2015 at 11:01 PM, Jiang Liu <jiang.liu@linux.intel.com> wrote:
>> On 2015/7/25 1:38, Alex Deucher wrote:
>>> On Thu, Jul 23, 2015 at 2:44 PM, Alex Deucher <alexdeucher@gmail.com> wrote:
>>>> On Thu, Jul 23, 2015 at 2:35 PM, Tejun Heo <tj@kernel.org> wrote:
>>>>> Hello,
>>>>>
>>>>> On Thu, Jul 23, 2015 at 01:48:24PM -0400, Alex Deucher wrote:
>>>>>> Something new in kernel 4.2 seems to have broken one of my hard drives
>>>>>> (ssd) in kernel 4.2. 4.1 and older kernels work fine. Here are the
>>>>>> relevant logs.
>>>>>>
>>>>> ...
>>>>>> [ 6.547628] ata2.00: qc timeout (cmd 0xec)
>>>>>> [ 6.547721] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>>>> [ 7.007213] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
>>>>>> [ 16.997819] ata2.00: qc timeout (cmd 0xec)
>>>>>> [ 16.997910] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>>>> [ 16.997995] ata2: limiting SATA link speed to 3.0 Gbps
>>>>>> [ 17.457400] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
>>>>>> [ 47.429257] ata2.00: qc timeout (cmd 0xec)
>>>>>> [ 47.429349] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>>>> [ 47.888822] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
>>>>>
>>>>> Nothing really rings a bell. Timeouts on IDENTIFY. Could be IRQ
>>>>> related. Which controller is it (lspci -nn)? Also, can you try to
>>>>> bisect the issue?
>>>>
>>>> 00:11.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD] FCH
>>>> SATA Controller [AHCI mode] [1022:7801] (rev 40)
>>>> 00:14.1 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD] FCH
>>>> IDE Controller [1022:780c]
>>>>
>>>> I can take a look at bisecting later this week.
>>>
>>> You were right about the interrupts. This is an AMD Kaveri APU system.
>> Hi Alex,
>> Could you please help to provide more information about the
>> system so we could identify the issue? Dmesg and /proc/interrupts
>> from good and bad kernels are welcomed.
>> Thanks!
>> Gerry
>
> See attached. Thanks!
Hi Alex,
Thanks for the info. Seems something is wrong with multiple-MSI
support. To narrow down the scope, could you please help to:
1) apply the small patch and retest
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 7e62751abfac..35f524cc23b7 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -1345,6 +1345,7 @@ static int ahci_init_msi(struct pci_dev *pdev,
unsigned int n_ports,
if (nvec < 0)
return nvec;
+ nvec = 1;
/*
* If number of MSIs is less than number of ports then Sharing Last
* Message mode could be enforced. In this case assume that
advantage
2) Disable interrupt remapping by kernel parameter "nointremap"
and retest.
Thanks!
Gerry
^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: ATA failure regression in kernel 4.2
2015-07-27 16:30 ` Jiang Liu
@ 2015-07-27 17:36 ` Alex Deucher
2015-07-28 18:19 ` Alex Deucher
1 sibling, 0 replies; 15+ messages in thread
From: Alex Deucher @ 2015-07-27 17:36 UTC (permalink / raw)
To: Jiang Liu; +Cc: Tejun Heo, LKML
[-- Attachment #1: Type: text/plain, Size: 3067 bytes --]
On Mon, Jul 27, 2015 at 12:30 PM, Jiang Liu <jiang.liu@linux.intel.com> wrote:
> On 2015/7/27 23:21, Alex Deucher wrote:
>> On Sun, Jul 26, 2015 at 11:01 PM, Jiang Liu <jiang.liu@linux.intel.com> wrote:
>>> On 2015/7/25 1:38, Alex Deucher wrote:
>>>> On Thu, Jul 23, 2015 at 2:44 PM, Alex Deucher <alexdeucher@gmail.com> wrote:
>>>>> On Thu, Jul 23, 2015 at 2:35 PM, Tejun Heo <tj@kernel.org> wrote:
>>>>>> Hello,
>>>>>>
>>>>>> On Thu, Jul 23, 2015 at 01:48:24PM -0400, Alex Deucher wrote:
>>>>>>> Something new in kernel 4.2 seems to have broken one of my hard drives
>>>>>>> (ssd) in kernel 4.2. 4.1 and older kernels work fine. Here are the
>>>>>>> relevant logs.
>>>>>>>
>>>>>> ...
>>>>>>> [ 6.547628] ata2.00: qc timeout (cmd 0xec)
>>>>>>> [ 6.547721] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>>>>> [ 7.007213] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
>>>>>>> [ 16.997819] ata2.00: qc timeout (cmd 0xec)
>>>>>>> [ 16.997910] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>>>>> [ 16.997995] ata2: limiting SATA link speed to 3.0 Gbps
>>>>>>> [ 17.457400] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
>>>>>>> [ 47.429257] ata2.00: qc timeout (cmd 0xec)
>>>>>>> [ 47.429349] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>>>>> [ 47.888822] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
>>>>>>
>>>>>> Nothing really rings a bell. Timeouts on IDENTIFY. Could be IRQ
>>>>>> related. Which controller is it (lspci -nn)? Also, can you try to
>>>>>> bisect the issue?
>>>>>
>>>>> 00:11.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD] FCH
>>>>> SATA Controller [AHCI mode] [1022:7801] (rev 40)
>>>>> 00:14.1 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD] FCH
>>>>> IDE Controller [1022:780c]
>>>>>
>>>>> I can take a look at bisecting later this week.
>>>>
>>>> You were right about the interrupts. This is an AMD Kaveri APU system.
>>> Hi Alex,
>>> Could you please help to provide more information about the
>>> system so we could identify the issue? Dmesg and /proc/interrupts
>>> from good and bad kernels are welcomed.
>>> Thanks!
>>> Gerry
>>
>> See attached. Thanks!
> Hi Alex,
> Thanks for the info. Seems something is wrong with multiple-MSI
> support. To narrow down the scope, could you please help to:
> 1) apply the small patch and retest
> diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
> index 7e62751abfac..35f524cc23b7 100644
> --- a/drivers/ata/ahci.c
> +++ b/drivers/ata/ahci.c
> @@ -1345,6 +1345,7 @@ static int ahci_init_msi(struct pci_dev *pdev,
> unsigned int n_ports,
> if (nvec < 0)
> return nvec;
>
> + nvec = 1;
> /*
> * If number of MSIs is less than number of ports then Sharing Last
> * Message mode could be enforced. In this case assume that
> advantage
This worked.
> 2) Disable interrupt remapping by kernel parameter "nointremap"
> and retest.
nointremap worked too.
dmesg and /proc/interrupts output for both tests attached.
Alex
[-- Attachment #2: interrupts.nointremap --]
[-- Type: application/octet-stream, Size: 4187 bytes --]
CPU0 CPU1 CPU2 CPU3
0: 135 0 0 0 IO-APIC 2-edge timer
1: 3 2 1 3 IO-APIC 1-edge i8042
7: 1 0 0 0 IO-APIC 7-edge
8: 0 0 0 1 IO-APIC 8-edge rtc0
9: 0 0 0 0 IO-APIC 9-fasteoi acpi
14: 0 0 0 0 IO-APIC 14-edge pata_atiixp
15: 0 0 0 0 IO-APIC 15-edge pata_atiixp
16: 305 307 302 305 IO-APIC 16-fasteoi snd_hda_intel
17: 0 0 0 0 IO-APIC 17-fasteoi ehci_hcd:usb7, ehci_hcd:usb8
18: 0 0 0 0 IO-APIC 18-fasteoi ohci_hcd:usb9, ohci_hcd:usb10, ohci_hcd:usb11
24: 0 0 0 0 PCI-MSI 4096-edge AMD-Vi
25: 0 0 0 0 PCI-MSI 344064-edge PCIe PME
26: 0 0 0 0 PCI-MSI 348160-edge PCIe PME
27: 0 0 0 0 PCI-MSI 350208-edge PCIe PME
28: 545 1619 1443 4747 PCI-MSI 278528-edge 0000:00:11.0
29: 2 2 0 18 PCI-MSI 262144-edge xhci_hcd
30: 0 0 0 0 PCI-MSI 262145-edge xhci_hcd
31: 0 0 0 0 PCI-MSI 262146-edge xhci_hcd
32: 0 0 0 0 PCI-MSI 262147-edge xhci_hcd
33: 0 0 0 0 PCI-MSI 262148-edge xhci_hcd
34: 0 0 0 0 PCI-MSI 264192-edge xhci_hcd
35: 0 0 0 0 PCI-MSI 264193-edge xhci_hcd
36: 0 0 0 0 PCI-MSI 264194-edge xhci_hcd
37: 0 0 0 0 PCI-MSI 264195-edge xhci_hcd
38: 0 0 0 0 PCI-MSI 264196-edge xhci_hcd
39: 0 0 0 0 PCI-MSI 1572864-edge xhci_hcd
40: 0 0 0 0 PCI-MSI 1572865-edge xhci_hcd
41: 0 0 0 0 PCI-MSI 1572866-edge xhci_hcd
42: 0 0 0 0 PCI-MSI 1572867-edge xhci_hcd
43: 0 0 0 0 PCI-MSI 1572868-edge xhci_hcd
45: 32 32 32 34 PCI-MSI 18432-edge snd_hda_intel
46: 28 1639 55 94 PCI-MSI 2097152-edge em1
NMI: 0 0 0 0 Non-maskable interrupts
LOC: 9917 7223 8681 7271 Local timer interrupts
SPU: 0 0 0 0 Spurious interrupts
PMI: 0 0 0 0 Performance monitoring interrupts
IWI: 1 0 1 2 IRQ work interrupts
RTR: 0 0 0 0 APIC ICR read retries
RES: 5232 4168 5812 2743 Rescheduling interrupts
CAL: 484 544 412 565 Function call interrupts
TLB: 122 165 343 112 TLB shootdowns
TRM: 0 0 0 0 Thermal event interrupts
THR: 0 0 0 0 Threshold APIC interrupts
DFR: 0 0 0 0 Deferred Error APIC interrupts
MCE: 0 0 0 0 Machine check exceptions
MCP: 1 1 1 1 Machine check polls
HYP: 0 0 0 0 Hypervisor callback interrupts
ERR: 1
MIS: 0
PIN: 0 0 0 0 Posted-interrupt notification event
PIW: 0 0 0 0 Posted-interrupt wakeup event
[-- Attachment #3: interrupts.nvec1 --]
[-- Type: application/octet-stream, Size: 4249 bytes --]
CPU0 CPU1 CPU2 CPU3
0: 139 0 0 0 IR-IO-APIC 2-edge timer
1: 2 2 1 4 IR-IO-APIC 1-edge i8042
7: 1 0 0 0 IR-IO-APIC 7-edge
8: 0 0 0 1 IR-IO-APIC 8-edge rtc0
9: 0 0 0 0 IR-IO-APIC 9-fasteoi acpi
14: 0 0 0 0 IR-IO-APIC 14-edge pata_atiixp
15: 0 0 0 0 IR-IO-APIC 15-edge pata_atiixp
16: 219 221 472 310 IR-IO-APIC 16-fasteoi snd_hda_intel
17: 0 0 0 0 IR-IO-APIC 17-fasteoi ehci_hcd:usb7, ehci_hcd:usb8
18: 0 0 0 0 IR-IO-APIC 18-fasteoi ohci_hcd:usb9, ohci_hcd:usb10, ohci_hcd:usb11
24: 0 0 0 0 PCI-MSI 4096-edge AMD-Vi
25: 0 0 0 0 IR-PCI-MSI 344064-edge PCIe PME
26: 0 0 0 0 IR-PCI-MSI 348160-edge PCIe PME
27: 0 0 0 0 IR-PCI-MSI 350208-edge PCIe PME
28: 334 750 1275 4680 IR-PCI-MSI 278528-edge 0000:00:11.0
29: 2 3 3 14 IR-PCI-MSI 262144-edge xhci_hcd
30: 0 0 0 0 IR-PCI-MSI 262145-edge xhci_hcd
31: 0 0 0 0 IR-PCI-MSI 262146-edge xhci_hcd
32: 0 0 0 0 IR-PCI-MSI 262147-edge xhci_hcd
33: 0 0 0 0 IR-PCI-MSI 262148-edge xhci_hcd
34: 0 0 0 0 IR-PCI-MSI 264192-edge xhci_hcd
35: 0 0 0 0 IR-PCI-MSI 264193-edge xhci_hcd
36: 0 0 0 0 IR-PCI-MSI 264194-edge xhci_hcd
37: 0 0 0 0 IR-PCI-MSI 264195-edge xhci_hcd
38: 0 0 0 0 IR-PCI-MSI 264196-edge xhci_hcd
39: 0 0 0 0 IR-PCI-MSI 1572864-edge xhci_hcd
40: 0 0 0 0 IR-PCI-MSI 1572865-edge xhci_hcd
41: 0 0 0 0 IR-PCI-MSI 1572866-edge xhci_hcd
42: 0 0 0 0 IR-PCI-MSI 1572867-edge xhci_hcd
43: 0 0 0 0 IR-PCI-MSI 1572868-edge xhci_hcd
45: 24 25 25 24 IR-PCI-MSI 18432-edge snd_hda_intel
46: 19 309 38 64 IR-PCI-MSI 2097152-edge em1
NMI: 0 0 0 0 Non-maskable interrupts
LOC: 7663 7181 8927 7595 Local timer interrupts
SPU: 0 0 0 0 Spurious interrupts
PMI: 0 0 0 0 Performance monitoring interrupts
IWI: 0 1 1 1 IRQ work interrupts
RTR: 0 0 0 0 APIC ICR read retries
RES: 5092 3637 5197 2573 Rescheduling interrupts
CAL: 548 521 583 450 Function call interrupts
TLB: 116 112 136 76 TLB shootdowns
TRM: 0 0 0 0 Thermal event interrupts
THR: 0 0 0 0 Threshold APIC interrupts
DFR: 0 0 0 0 Deferred Error APIC interrupts
MCE: 0 0 0 0 Machine check exceptions
MCP: 1 1 1 1 Machine check polls
HYP: 0 0 0 0 Hypervisor callback interrupts
ERR: 1
MIS: 0
PIN: 0 0 0 0 Posted-interrupt notification event
PIW: 0 0 0 0 Posted-interrupt wakeup event
[-- Attachment #4: dmesg.nvec1 --]
[-- Type: application/octet-stream, Size: 59799 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.2.0-rc2+ (alex@cm) (gcc version 4.8.3 20140624 (Red Hat 4.8.3-1) (GCC) ) #794 SMP Mon Jul 27 13:25:46 EDT 2015
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.2.0-rc2+ root=/dev/mapper/fedora-root ro rd.lvm.lv=fedora/swap rd.md=0 rd.dm=0 vconsole.keymap=us rd.luks=0 vconsole.font=latarcyrheb-sun16 rd.lvm.lv=fedora/root LANG=en_US.UTF-8 modprobe.blacklist=amdgpu,radeon 3
[ 0.000000] tseg: 007f800000
[ 0.000000] x86/fpu: xstate_offset[2]: 0240, xstate_sizes[2]: 0100
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x01: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x02: 'SSE registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x04: 'AVX registers'
[ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 0x340 bytes, using 'standard' format.
[ 0.000000] x86/fpu: Using 'eager' FPU context switches.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009e7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009e800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007bc3afff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007bc3b000-0x000000007bc6afff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007bc6b000-0x000000007bf29fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007bf2a000-0x000000007bfe5fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007bfe6000-0x000000007e10afff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007e10b000-0x000000007e10bfff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007e10c000-0x000000007e311fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007e312000-0x000000007e467fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007e468000-0x000000007f02efff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007f02f000-0x000000007f071fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007f072000-0x000000007f7f0fff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007f7f1000-0x000000007f7fffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec01fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed40000-0x00000000fed44fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff800000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000043effffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: To Be Filled By O.E.M. To Be Filled By O.E.M./FM2A88X Extreme6+, BIOS P2.70 01/15/2014
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x43f000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF write-through
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-E7FFF uncachable
[ 0.000000] E8000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000000 mask FFFF80000000 write-back
[ 0.000000] 1 base 00007F800000 mask FFFFFF800000 uncachable
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 000000043f000000 aka 17392M
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WC UC- WT
[ 0.000000] e820: update [mem 0x7f800000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0x7f800 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000fd8a0-0x000fd8af] mapped at [ffff8800000fd8a0]
[ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x02016000, 0x02016fff] PGTABLE
[ 0.000000] BRK [0x02017000, 0x02017fff] PGTABLE
[ 0.000000] BRK [0x02018000, 0x02018fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x43ee00000-0x43effffff]
[ 0.000000] [mem 0x43ee00000-0x43effffff] page 2M
[ 0.000000] BRK [0x02019000, 0x02019fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x420000000-0x43edfffff]
[ 0.000000] [mem 0x420000000-0x43edfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x400000000-0x41fffffff]
[ 0.000000] [mem 0x400000000-0x41fffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x7bc3afff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x7bbfffff] page 2M
[ 0.000000] [mem 0x7bc00000-0x7bc3afff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x7bc6b000-0x7bf29fff]
[ 0.000000] [mem 0x7bc6b000-0x7bf29fff] page 4k
[ 0.000000] BRK [0x0201a000, 0x0201afff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x7e10b000-0x7e10bfff]
[ 0.000000] [mem 0x7e10b000-0x7e10bfff] page 4k
[ 0.000000] BRK [0x0201b000, 0x0201bfff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x7e312000-0x7e467fff]
[ 0.000000] [mem 0x7e312000-0x7e467fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x7f02f000-0x7f071fff]
[ 0.000000] [mem 0x7f02f000-0x7f071fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x7f7f1000-0x7f7fffff]
[ 0.000000] [mem 0x7f7f1000-0x7f7fffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x3ffffffff]
[ 0.000000] [mem 0x100000000-0x3ffffffff] page 1G
[ 0.000000] RAMDISK: [mem 0x334ae000-0x35a4efff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F04A0 000024 (v02 ALASKA)
[ 0.000000] ACPI: XSDT 0x000000007BFAE080 00007C (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 0x000000007BFB40E8 00010C (v05 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has zero address or length: 0x0000000000000000/0x1 (20150619/tbfadt-654)
[ 0.000000] ACPI: DSDT 0x000000007BFAE190 005F58 (v02 ALASKA A M I 00000000 INTL 20051117)
[ 0.000000] ACPI: FACS 0x000000007BFDC080 000040
[ 0.000000] ACPI: APIC 0x000000007BFB41F8 00007E (v03 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FPDT 0x000000007BFB4278 000044 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: MCFG 0x000000007BFB42C0 00003C (v01 ALASKA A M I 01072009 MSFT 00010013)
[ 0.000000] ACPI: HPET 0x000000007BFB4300 000038 (v01 ALASKA A M I 01072009 AMI 00000005)
[ 0.000000] ACPI: AAFT 0x000000007BFB4338 0002F5 (v01 ALASKA OEMAAFT 01072009 MSFT 00000097)
[ 0.000000] ACPI: IVRS 0x000000007BFB4630 000078 (v02 AMD BANTRY 00000001 AMD 00000000)
[ 0.000000] ACPI: SSDT 0x000000007BFB46A8 000B9C (v01 AMD BANTRY 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 0x000000007BFB5248 00033B (v02 AMD BANTRY 00000002 MSFT 04000000)
[ 0.000000] ACPI: CRAT 0x000000007BFB5588 0005A0 (v01 AMD BANTRY 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 0x000000007BFB5B28 001115 (v01 AMD CPMCMN 00000001 INTL 20051117)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000043effffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x43efe6000-0x43eff9fff]
[ 0.000000] [ffffea0000000000-ffffea0010ffffff] PMD -> [ffff88042f600000-ffff88043e5fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000043effffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009dfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x000000007bc3afff]
[ 0.000000] node 0: [mem 0x000000007bc6b000-0x000000007bf29fff]
[ 0.000000] node 0: [mem 0x000000007e10b000-0x000000007e10bfff]
[ 0.000000] node 0: [mem 0x000000007e312000-0x000000007e467fff]
[ 0.000000] node 0: [mem 0x000000007f02f000-0x000000007f071fff]
[ 0.000000] node 0: [mem 0x000000007f7f1000-0x000000007f7fffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000043effffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000043effffff]
[ 0.000000] On node 0 totalpages: 3911744
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3997 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7875 pages used for memmap
[ 0.000000] DMA32 zone: 503971 pages, LIFO batch:31
[ 0.000000] Normal zone: 53184 pages used for memmap
[ 0.000000] Normal zone: 3403776 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 5, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] IOAPIC[1]: apic_id 6, version 33, address 0xfec01000, GSI 24-55
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10228210 base: 0xfed00000
[ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009efff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7bc3b000-0x7bc6afff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7bf2a000-0x7bfe5fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7bfe6000-0x7e10afff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7e10c000-0x7e311fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7e468000-0x7f02efff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7f072000-0x7f7f0fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7f800000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec01fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec02000-0xfec0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec10000-0xfec10fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec11000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed01000-0xfed3ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed40000-0xfed44fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed45000-0xfed7ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed80000-0xfed8ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed90000-0xff7fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff800000-0xffffffff]
[ 0.000000] e820: [mem 0x7f800000-0xfebfffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 33 pages/cpu @ffff88043ec00000 s95448 r8192 d31528 u524288
[ 0.000000] pcpu-alloc: s95448 r8192 d31528 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 3850600
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.2.0-rc2+ root=/dev/mapper/fedora-root ro rd.lvm.lv=fedora/swap rd.md=0 rd.dm=0 vconsole.keymap=us rd.luks=0 vconsole.font=latarcyrheb-sun16 rd.lvm.lv=fedora/root LANG=en_US.UTF-8 modprobe.blacklist=amdgpu,radeon 3
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Memory: 15279264K/15646976K available (7209K kernel code, 1195K rwdata, 3220K rodata, 1520K init, 1428K bss, 367712K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000] NR_IRQS:8448 nr_irqs:1000 16
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 3693.245 MHz processor
[ 0.000023] Calibrating delay loop (skipped), value calculated using timer frequency.. 7386.49 BogoMIPS (lpj=3693245)
[ 0.000194] pid_max: default: 32768 minimum: 301
[ 0.000281] ACPI: Core revision 20150619
[ 0.003742] ACPI: All ACPI Tables successfully acquired
[ 0.003892] Security Framework initialized
[ 0.003973] SELinux: Initializing.
[ 0.004057] SELinux: Starting in permissive mode
[ 0.005049] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.009628] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.011713] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.011814] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.012248] Initializing cgroup subsys blkio
[ 0.012334] Initializing cgroup subsys devices
[ 0.012417] Initializing cgroup subsys freezer
[ 0.012501] Initializing cgroup subsys net_cls
[ 0.012584] Initializing cgroup subsys perf_event
[ 0.012682] CPU: Physical Processor ID: 0
[ 0.012763] CPU: Processor Core ID: 0
[ 0.012845] mce: CPU supports 7 MCE banks
[ 0.012931] LVT offset 1 assigned for vector 0xf9
[ 0.013017] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512
[ 0.013109] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0
[ 0.013290] Freeing SMP alternatives memory: 28K (ffffffff81ea8000 - ffffffff81eaf000)
[ 0.022214] ftrace: allocating 27833 entries in 109 pages
[ 0.111351] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.222872] smpboot: CPU0: AMD A10-7850K APU with Radeon(TM) R7 Graphics (fam: 15, model: 30, stepping: 01)
[ 0.224897] Performance Events: Fam15h core perfctr, AMD PMU driver.
[ 0.225061] ... version: 0
[ 0.225143] ... bit width: 48
[ 0.225224] ... generic registers: 6
[ 0.225305] ... value mask: 0000ffffffffffff
[ 0.225387] ... max period: 00007fffffffffff
[ 0.225468] ... fixed-purpose events: 0
[ 0.225549] ... event mask: 000000000000003f
[ 0.226164] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.226365] x86: Booting SMP configuration:
[ 0.226446] .... node #0, CPUs: #1 #2 #3
[ 0.236092] x86: Booted up 1 node, 4 CPUs
[ 0.236252] smpboot: Total of 4 processors activated (29545.96 BogoMIPS)
[ 0.237042] devtmpfs: initialized
[ 0.237352] PM: Registering ACPI NVS region [mem 0x7bf2a000-0x7bfe5fff] (770048 bytes)
[ 0.237493] PM: Registering ACPI NVS region [mem 0x7e10c000-0x7e311fff] (2121728 bytes)
[ 0.237710] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.237924] atomic64_test: passed for x86-64 platform with CX8 and with SSE
[ 0.238005] pinctrl core: initialized pinctrl subsystem
[ 0.238125] RTC time: 17:32:48, date: 07/27/15
[ 0.238303] NET: Registered protocol family 16
[ 0.240861] cpuidle: using governor ladder
[ 0.244865] cpuidle: using governor menu
[ 0.245068] ACPI: bus type PCI registered
[ 0.245151] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.245314] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.245455] PCI: not using MMCONFIG
[ 0.245536] PCI: Using configuration type 1 for base access
[ 0.245619] PCI: Using configuration type 1 for extended access
[ 0.249213] ACPI: Added _OSI(Module Device)
[ 0.249300] ACPI: Added _OSI(Processor Device)
[ 0.249382] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.249465] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.250855] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.253097] ACPI: Interpreter enabled
[ 0.253183] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20150619/hwxface-580)
[ 0.253371] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150619/hwxface-580)
[ 0.253567] ACPI: (supports S0 S3 S4 S5)
[ 0.253654] ACPI: Using IOAPIC for interrupt routing
[ 0.253751] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.253924] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[ 0.254077] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.258317] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.258404] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.258696] acpi PNP0A03:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[ 0.259065] PCI host bridge to bus 0000:00
[ 0.259147] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.259227] pci_bus 0000:00: root bus resource [io 0x0000-0x03af window]
[ 0.259308] pci_bus 0000:00: root bus resource [io 0x03e0-0x0cf7 window]
[ 0.259389] pci_bus 0000:00: root bus resource [io 0x03b0-0x03df window]
[ 0.259470] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.259551] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.259691] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[ 0.259830] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff window]
[ 0.259979] pci 0000:00:00.0: [1022:1422] type 00 class 0x060000
[ 0.260061] pci 0000:00:00.2: [1022:1423] type 00 class 0x080600
[ 0.260144] pci 0000:00:01.0: [1002:130f] type 00 class 0x030000
[ 0.260159] pci 0000:00:01.0: reg 0x10: [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.260164] pci 0000:00:01.0: reg 0x18: [mem 0xd0000000-0xd07fffff 64bit pref]
[ 0.260169] pci 0000:00:01.0: reg 0x20: [io 0xf000-0xf0ff]
[ 0.260173] pci 0000:00:01.0: reg 0x24: [mem 0xff700000-0xff73ffff]
[ 0.260177] pci 0000:00:01.0: reg 0x30: [mem 0xff740000-0xff75ffff pref]
[ 0.260192] pci 0000:00:01.0: supports D1 D2
[ 0.260193] pci 0000:00:01.0: PME# supported from D1 D2 D3hot
[ 0.260256] pci 0000:00:01.1: [1002:1308] type 00 class 0x040300
[ 0.260269] pci 0000:00:01.1: reg 0x10: [mem 0xff764000-0xff767fff 64bit]
[ 0.260293] pci 0000:00:01.1: supports D1 D2
[ 0.260347] pci 0000:00:02.0: [1022:1424] type 00 class 0x060000
[ 0.260415] pci 0000:00:03.0: [1022:1424] type 00 class 0x060000
[ 0.260484] pci 0000:00:04.0: [1022:1424] type 00 class 0x060000
[ 0.260573] pci 0000:00:10.0: [1022:7814] type 00 class 0x0c0330
[ 0.260616] pci 0000:00:10.0: reg 0x10: [mem 0xff76a000-0xff76bfff 64bit]
[ 0.260680] pci 0000:00:10.0: PME# supported from D0 D3hot D3cold
[ 0.260720] pci 0000:00:10.0: System wakeup disabled by ACPI
[ 0.260846] pci 0000:00:10.1: [1022:7814] type 00 class 0x0c0330
[ 0.260892] pci 0000:00:10.1: reg 0x10: [mem 0xff768000-0xff769fff 64bit]
[ 0.260956] pci 0000:00:10.1: PME# supported from D0 D3hot D3cold
[ 0.260994] pci 0000:00:10.1: System wakeup disabled by ACPI
[ 0.261116] pci 0000:00:11.0: [1022:7801] type 00 class 0x010601
[ 0.261137] pci 0000:00:11.0: reg 0x10: [io 0xf190-0xf197]
[ 0.261144] pci 0000:00:11.0: reg 0x14: [io 0xf180-0xf183]
[ 0.261151] pci 0000:00:11.0: reg 0x18: [io 0xf170-0xf177]
[ 0.261159] pci 0000:00:11.0: reg 0x1c: [io 0xf160-0xf163]
[ 0.261166] pci 0000:00:11.0: reg 0x20: [io 0xf150-0xf15f]
[ 0.261173] pci 0000:00:11.0: reg 0x24: [mem 0xff771000-0xff7717ff]
[ 0.261247] pci 0000:00:12.0: [1022:7807] type 00 class 0x0c0310
[ 0.261259] pci 0000:00:12.0: reg 0x10: [mem 0xff770000-0xff770fff]
[ 0.261327] pci 0000:00:12.0: System wakeup disabled by ACPI
[ 0.261443] pci 0000:00:12.2: [1022:7808] type 00 class 0x0c0320
[ 0.261463] pci 0000:00:12.2: reg 0x10: [mem 0xff76f000-0xff76f0ff]
[ 0.261514] pci 0000:00:12.2: supports D1 D2
[ 0.261515] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.261545] pci 0000:00:12.2: System wakeup disabled by ACPI
[ 0.261668] pci 0000:00:13.0: [1022:7807] type 00 class 0x0c0310
[ 0.261681] pci 0000:00:13.0: reg 0x10: [mem 0xff76e000-0xff76efff]
[ 0.261751] pci 0000:00:13.0: System wakeup disabled by ACPI
[ 0.261884] pci 0000:00:13.2: [1022:7808] type 00 class 0x0c0320
[ 0.261904] pci 0000:00:13.2: reg 0x10: [mem 0xff76d000-0xff76d0ff]
[ 0.261955] pci 0000:00:13.2: supports D1 D2
[ 0.261957] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.261988] pci 0000:00:13.2: System wakeup disabled by ACPI
[ 0.262107] pci 0000:00:14.0: [1022:780b] type 00 class 0x0c0500
[ 0.262204] pci 0000:00:14.1: [1022:780c] type 00 class 0x01018a
[ 0.262216] pci 0000:00:14.1: reg 0x10: [io 0xf140-0xf147]
[ 0.262223] pci 0000:00:14.1: reg 0x14: [io 0xf130-0xf133]
[ 0.262230] pci 0000:00:14.1: reg 0x18: [io 0xf120-0xf127]
[ 0.262237] pci 0000:00:14.1: reg 0x1c: [io 0xf110-0xf113]
[ 0.262245] pci 0000:00:14.1: reg 0x20: [io 0xf100-0xf10f]
[ 0.262260] pci 0000:00:14.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.262343] pci 0000:00:14.1: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.262427] pci 0000:00:14.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.262510] pci 0000:00:14.1: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.262656] pci 0000:00:14.2: [1022:780d] type 00 class 0x040300
[ 0.262677] pci 0000:00:14.2: reg 0x10: [mem 0xff760000-0xff763fff 64bit]
[ 0.262720] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[ 0.262749] pci 0000:00:14.2: System wakeup disabled by ACPI
[ 0.262871] pci 0000:00:14.3: [1022:780e] type 00 class 0x060100
[ 0.262987] pci 0000:00:14.4: [1022:780f] type 01 class 0x060401
[ 0.263042] pci 0000:00:14.4: System wakeup disabled by ACPI
[ 0.263154] pci 0000:00:14.5: [1022:7809] type 00 class 0x0c0310
[ 0.263166] pci 0000:00:14.5: reg 0x10: [mem 0xff76c000-0xff76cfff]
[ 0.263235] pci 0000:00:14.5: System wakeup disabled by ACPI
[ 0.263351] pci 0000:00:15.0: [1022:43a0] type 01 class 0x060400
[ 0.263400] pci 0000:00:15.0: supports D1 D2
[ 0.263401] pci 0000:00:15.0: PME# supported from D0 D3hot D3cold
[ 0.263435] pci 0000:00:15.0: System wakeup disabled by ACPI
[ 0.263551] pci 0000:00:15.2: [1022:43a2] type 01 class 0x060400
[ 0.263609] pci 0000:00:15.2: supports D1 D2
[ 0.263611] pci 0000:00:15.2: PME# supported from D0 D3hot D3cold
[ 0.263643] pci 0000:00:15.2: System wakeup disabled by ACPI
[ 0.263758] pci 0000:00:15.3: [1022:43a3] type 01 class 0x060400
[ 0.263807] pci 0000:00:15.3: supports D1 D2
[ 0.263808] pci 0000:00:15.3: PME# supported from D0 D3hot D3cold
[ 0.263842] pci 0000:00:15.3: System wakeup disabled by ACPI
[ 0.263966] pci 0000:00:18.0: [1022:141a] type 00 class 0x060000
[ 0.264021] pci 0000:00:18.1: [1022:141b] type 00 class 0x060000
[ 0.264075] pci 0000:00:18.2: [1022:141c] type 00 class 0x060000
[ 0.264128] pci 0000:00:18.3: [1022:141d] type 00 class 0x060000
[ 0.264183] pci 0000:00:18.4: [1022:141e] type 00 class 0x060000
[ 0.264236] pci 0000:00:18.5: [1022:141f] type 00 class 0x060000
[ 0.264360] pci 0000:00:14.4: PCI bridge to [bus 01] (subtractive decode)
[ 0.264450] pci 0000:00:14.4: bridge window [io 0x0000-0x03af window] (subtractive decode)
[ 0.264452] pci 0000:00:14.4: bridge window [io 0x03e0-0x0cf7 window] (subtractive decode)
[ 0.264453] pci 0000:00:14.4: bridge window [io 0x03b0-0x03df window] (subtractive decode)
[ 0.264454] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode)
[ 0.264456] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[ 0.264457] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000dffff window] (subtractive decode)
[ 0.264459] pci 0000:00:14.4: bridge window [mem 0xc0000000-0xffffffff window] (subtractive decode)
[ 0.264497] pci 0000:00:15.0: PCI bridge to [bus 02]
[ 0.264646] pci 0000:03:00.0: [1b21:1042] type 00 class 0x0c0330
[ 0.264686] pci 0000:03:00.0: reg 0x10: [mem 0xff600000-0xff607fff 64bit]
[ 0.264778] pci 0000:03:00.0: PME# supported from D3hot D3cold
[ 0.266851] pci 0000:00:15.2: PCI bridge to [bus 03]
[ 0.266945] pci 0000:00:15.2: bridge window [mem 0xff600000-0xff6fffff]
[ 0.267033] pci 0000:04:00.0: [1969:10a1] type 00 class 0x020000
[ 0.267079] pci 0000:04:00.0: reg 0x10: [mem 0xff500000-0xff53ffff 64bit]
[ 0.267091] pci 0000:04:00.0: reg 0x18: [io 0xe000-0xe07f]
[ 0.267171] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.268850] pci 0000:00:15.3: PCI bridge to [bus 04]
[ 0.268942] pci 0000:00:15.3: bridge window [io 0xe000-0xefff]
[ 0.268945] pci 0000:00:15.3: bridge window [mem 0xff500000-0xff5fffff]
[ 0.269387] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 7 10 *11 14 15)
[ 0.269756] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 5 7 10 *11 14 15)
[ 0.270130] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 7 *10 11 14 15)
[ 0.270489] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 *5 7 10 11 14 15)
[ 0.270854] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 10 11 14 15) *0
[ 0.271224] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 10 11 14 15) *0
[ 0.271603] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 5 7 10 11 14 15) *0
[ 0.271980] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 7 10 11 14 15) *0
[ 0.272571] vgaarb: setting as boot device: PCI:0000:00:01.0
[ 0.272654] vgaarb: device added: PCI:0000:00:01.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.272792] vgaarb: loaded
[ 0.272874] vgaarb: bridge control possible 0000:00:01.0
[ 0.273026] SCSI subsystem initialized
[ 0.273160] libata version 3.00 loaded.
[ 0.273188] ACPI: bus type USB registered
[ 0.273283] usbcore: registered new interface driver usbfs
[ 0.273369] usbcore: registered new interface driver hub
[ 0.273463] usbcore: registered new device driver usb
[ 0.273643] PCI: Using ACPI for IRQ routing
[ 0.280254] PCI: pci_cache_line_size set to 64 bytes
[ 0.280312] e820: reserve RAM buffer [mem 0x0009e800-0x0009ffff]
[ 0.280314] e820: reserve RAM buffer [mem 0x7bc3b000-0x7bffffff]
[ 0.280315] e820: reserve RAM buffer [mem 0x7bf2a000-0x7bffffff]
[ 0.280316] e820: reserve RAM buffer [mem 0x7e10c000-0x7fffffff]
[ 0.280317] e820: reserve RAM buffer [mem 0x7e468000-0x7fffffff]
[ 0.280318] e820: reserve RAM buffer [mem 0x7f072000-0x7fffffff]
[ 0.280319] e820: reserve RAM buffer [mem 0x7f800000-0x7fffffff]
[ 0.280320] e820: reserve RAM buffer [mem 0x43f000000-0x43fffffff]
[ 0.280425] NetLabel: Initializing
[ 0.280507] NetLabel: domain hash size = 128
[ 0.280595] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.280686] NetLabel: unlabeled traffic allowed by default
[ 0.280841] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.281030] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 0.283156] clocksource: Switched to clocksource hpet
[ 0.290115] pnp: PnP ACPI init
[ 0.290317] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.290400] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.290460] system 00:01: [mem 0x80000000-0xbfffffff] has been reserved
[ 0.290542] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.290597] system 00:02: [mem 0xfeb80000-0xfebfffff] could not be reserved
[ 0.290679] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.290763] system 00:03: [io 0x0290-0x029f] has been reserved
[ 0.290844] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.290940] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.290966] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.291009] system 00:06: [io 0x04d0-0x04d1] has been reserved
[ 0.291090] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.291122] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.291265] pnp 00:08: [dma 0 disabled]
[ 0.291302] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.291488] system 00:09: [io 0x04d0-0x04d1] has been reserved
[ 0.291568] system 00:09: [io 0x040b] has been reserved
[ 0.291649] system 00:09: [io 0x04d6] has been reserved
[ 0.291731] system 00:09: [io 0x0c00-0x0c01] has been reserved
[ 0.291811] system 00:09: [io 0x0c14] has been reserved
[ 0.291891] system 00:09: [io 0x0c50-0x0c51] has been reserved
[ 0.291971] system 00:09: [io 0x0c52] has been reserved
[ 0.292051] system 00:09: [io 0x0c6c] has been reserved
[ 0.292131] system 00:09: [io 0x0c6f] has been reserved
[ 0.292217] system 00:09: [io 0x0cd0-0x0cd1] has been reserved
[ 0.292297] system 00:09: [io 0x0cd2-0x0cd3] has been reserved
[ 0.292377] system 00:09: [io 0x0cd4-0x0cd5] has been reserved
[ 0.292457] system 00:09: [io 0x0cd6-0x0cd7] has been reserved
[ 0.292538] system 00:09: [io 0x0cd8-0x0cdf] has been reserved
[ 0.292618] system 00:09: [io 0x0800-0x089f] could not be reserved
[ 0.292698] system 00:09: [io 0x0b20-0x0b3f] has been reserved
[ 0.292778] system 00:09: [io 0x0900-0x090f] has been reserved
[ 0.292859] system 00:09: [io 0x0910-0x091f] has been reserved
[ 0.292939] system 00:09: [io 0xfe00-0xfefe] has been reserved
[ 0.293019] system 00:09: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.293102] system 00:09: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.293190] system 00:09: [mem 0xfed80000-0xfed8ffff] has been reserved
[ 0.293274] system 00:09: [mem 0xfed61000-0xfed70fff] has been reserved
[ 0.293357] system 00:09: [mem 0xfec10000-0xfec10fff] has been reserved
[ 0.293440] system 00:09: [mem 0xfed00000-0xfed00fff] could not be reserved
[ 0.293523] system 00:09: [mem 0xff800000-0xffffffff] has been reserved
[ 0.293607] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.293733] pnp: PnP ACPI: found 10 devices
[ 0.300340] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.300502] pci 0000:00:14.4: PCI bridge to [bus 01]
[ 0.300594] pci 0000:00:15.0: PCI bridge to [bus 02]
[ 0.300683] pci 0000:00:15.2: PCI bridge to [bus 03]
[ 0.300768] pci 0000:00:15.2: bridge window [mem 0xff600000-0xff6fffff]
[ 0.300855] pci 0000:00:15.3: PCI bridge to [bus 04]
[ 0.300938] pci 0000:00:15.3: bridge window [io 0xe000-0xefff]
[ 0.301023] pci 0000:00:15.3: bridge window [mem 0xff500000-0xff5fffff]
[ 0.301111] pci_bus 0000:00: resource 4 [io 0x0000-0x03af window]
[ 0.301113] pci_bus 0000:00: resource 5 [io 0x03e0-0x0cf7 window]
[ 0.301114] pci_bus 0000:00: resource 6 [io 0x03b0-0x03df window]
[ 0.301116] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff window]
[ 0.301117] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[ 0.301118] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[ 0.301119] pci_bus 0000:00: resource 10 [mem 0xc0000000-0xffffffff window]
[ 0.301121] pci_bus 0000:01: resource 4 [io 0x0000-0x03af window]
[ 0.301122] pci_bus 0000:01: resource 5 [io 0x03e0-0x0cf7 window]
[ 0.301124] pci_bus 0000:01: resource 6 [io 0x03b0-0x03df window]
[ 0.301125] pci_bus 0000:01: resource 7 [io 0x0d00-0xffff window]
[ 0.301126] pci_bus 0000:01: resource 8 [mem 0x000a0000-0x000bffff window]
[ 0.301127] pci_bus 0000:01: resource 9 [mem 0x000c0000-0x000dffff window]
[ 0.301129] pci_bus 0000:01: resource 10 [mem 0xc0000000-0xffffffff window]
[ 0.301130] pci_bus 0000:03: resource 1 [mem 0xff600000-0xff6fffff]
[ 0.301132] pci_bus 0000:04: resource 0 [io 0xe000-0xefff]
[ 0.301133] pci_bus 0000:04: resource 1 [mem 0xff500000-0xff5fffff]
[ 0.301166] NET: Registered protocol family 2
[ 0.301461] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.301883] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.302207] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.302343] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.302505] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.302707] NET: Registered protocol family 1
[ 0.302805] pci 0000:00:01.0: Video device with shadowed ROM
[ 0.541271] pci 0000:04:00.0: set MSI_INTX_DISABLE_BUG flag
[ 0.541361] PCI: CLS 64 bytes, default 64
[ 0.541429] Unpacking initramfs...
[ 1.032662] Freeing initrd memory: 38532K (ffff8800334ae000 - ffff880035a4f000)
[ 1.032848] AMD-Vi: IOMMU performance counters supported
[ 1.033068] ERROR: Unable to locate IOAPIC for GSI 56
[ 1.033153] pci 0000:00:00.2: PCI INT A: failed to register GSI
[ 1.034038] iommu: Adding device 0000:00:00.0 to group 0
[ 1.034482] iommu: Adding device 0000:00:01.0 to group 1
[ 1.034579] iommu: Using direct mapping for device 0000:00:01.0
[ 1.034677] iommu: Adding device 0000:00:01.1 to group 1
[ 1.035058] iommu: Adding device 0000:00:02.0 to group 2
[ 1.035490] iommu: Adding device 0000:00:03.0 to group 3
[ 1.035921] iommu: Adding device 0000:00:04.0 to group 4
[ 1.036361] iommu: Adding device 0000:00:10.0 to group 5
[ 1.038094] iommu: Adding device 0000:00:10.1 to group 5
[ 1.038522] iommu: Adding device 0000:00:11.0 to group 6
[ 1.038954] iommu: Adding device 0000:00:12.0 to group 7
[ 1.039046] iommu: Adding device 0000:00:12.2 to group 7
[ 1.039475] iommu: Adding device 0000:00:13.0 to group 8
[ 1.039568] iommu: Adding device 0000:00:13.2 to group 8
[ 1.039997] iommu: Adding device 0000:00:14.0 to group 9
[ 1.040089] iommu: Adding device 0000:00:14.1 to group 9
[ 1.040182] iommu: Adding device 0000:00:14.2 to group 9
[ 1.040274] iommu: Adding device 0000:00:14.3 to group 9
[ 1.040694] iommu: Adding device 0000:00:14.4 to group 10
[ 1.041109] iommu: Adding device 0000:00:14.5 to group 11
[ 1.041552] iommu: Adding device 0000:00:15.0 to group 12
[ 1.041648] iommu: Adding device 0000:00:15.2 to group 12
[ 1.041743] iommu: Adding device 0000:00:15.3 to group 12
[ 1.042195] iommu: Adding device 0000:00:18.0 to group 13
[ 1.042291] iommu: Adding device 0000:00:18.1 to group 13
[ 1.042387] iommu: Adding device 0000:00:18.2 to group 13
[ 1.042491] iommu: Adding device 0000:00:18.3 to group 13
[ 1.042587] iommu: Adding device 0000:00:18.4 to group 13
[ 1.042683] iommu: Adding device 0000:00:18.5 to group 13
[ 1.042775] iommu: Adding device 0000:03:00.0 to group 12
[ 1.042871] iommu: Adding device 0000:04:00.0 to group 12
[ 1.042953] AMD-Vi: Found IOMMU at 0000:00:00.2 cap 0x40
[ 1.043035] AMD-Vi: Extended features: PPR GT IA PC
[ 1.043250] AMD-Vi: Interrupt remapping enabled
[ 1.043566] AMD-Vi: Lazy IO/TLB flushing enabled
[ 1.045721] perf: AMD NB counters detected
[ 1.045825] perf: amd_iommu: Detected. (2 banks, 4 counters/bank)
[ 1.045932] LVT offset 0 assigned for vector 0x400
[ 1.046089] perf: AMD IBS detected (0x000001ff)
[ 1.046754] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 1.046856] Initialise system trusted keyring
[ 1.046952] audit: initializing netlink subsys (disabled)
[ 1.047055] audit: type=2000 audit(1438018368.856:1): initialized
[ 1.047531] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.049072] VFS: Disk quotas dquot_6.6.0
[ 1.049181] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.049612] SELinux: Registering netfilter hooks
[ 1.053208] NET: Registered protocol family 38
[ 1.053298] Key type asymmetric registered
[ 1.053378] Asymmetric key parser 'x509' registered
[ 1.053501] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.053694] io scheduler noop registered
[ 1.053780] io scheduler deadline registered
[ 1.053909] io scheduler cfq registered (default)
[ 1.054455] pcieport 0000:00:15.0: Signaling PME through PCIe PME interrupt
[ 1.054544] pcie_pme 0000:00:15.0:pcie01: service driver pcie_pme loaded
[ 1.054564] pcieport 0000:00:15.2: Signaling PME through PCIe PME interrupt
[ 1.054645] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
[ 1.054727] pcie_pme 0000:00:15.2:pcie01: service driver pcie_pme loaded
[ 1.054744] pcieport 0000:00:15.3: Signaling PME through PCIe PME interrupt
[ 1.054825] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt
[ 1.054907] pcie_pme 0000:00:15.3:pcie01: service driver pcie_pme loaded
[ 1.054913] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.054997] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.055167] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 1.055302] ACPI: Power Button [PWRB]
[ 1.055411] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 1.055563] ACPI: Power Button [PWRF]
[ 1.055677] ACPI: acpi_idle registered with cpuidle
[ 1.056046] GHES: HEST is not enabled!
[ 1.056236] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.076842] 00:08: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 1.077471] Non-volatile memory driver v1.3
[ 1.077593] Linux agpgart interface v0.103
[ 1.079136] loop: module loaded
[ 1.079321] ahci 0000:00:11.0: version 3.0
[ 1.079514] ahci 0000:00:11.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[ 1.079653] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck led clo pmp pio slum part sxs
[ 1.080171] scsi host0: ahci
[ 1.080346] scsi host1: ahci
[ 1.080482] ata1: SATA max UDMA/133 abar m2048@0xff771000 port 0xff771100 irq 28
[ 1.080620] ata2: SATA max UDMA/133 abar m2048@0xff771000 port 0xff771180 irq 28
[ 1.080836] libphy: Fixed MDIO Bus: probed
[ 1.081055] QUIRK: Enable AMD PLL fix
[ 1.081064] xhci_hcd 0000:00:10.0: xHCI Host Controller
[ 1.081185] xhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 1.081500] xhci_hcd 0000:00:10.0: hcc params 0x014040c3 hci version 0x100 quirks 0x00000418
[ 1.081788] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.081871] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.082017] usb usb1: Product: xHCI Host Controller
[ 1.082098] usb usb1: Manufacturer: Linux 4.2.0-rc2+ xhci-hcd
[ 1.082180] usb usb1: SerialNumber: 0000:00:10.0
[ 1.082470] hub 1-0:1.0: USB hub found
[ 1.082558] hub 1-0:1.0: 2 ports detected
[ 1.082713] xhci_hcd 0000:00:10.0: xHCI Host Controller
[ 1.082826] xhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[ 1.084924] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.085008] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.085153] usb usb2: Product: xHCI Host Controller
[ 1.085232] usb usb2: Manufacturer: Linux 4.2.0-rc2+ xhci-hcd
[ 1.085313] usb usb2: SerialNumber: 0000:00:10.0
[ 1.085558] hub 2-0:1.0: USB hub found
[ 1.085641] hub 2-0:1.0: 2 ports detected
[ 1.085846] xhci_hcd 0000:00:10.1: xHCI Host Controller
[ 1.085963] xhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 1.086267] xhci_hcd 0000:00:10.1: hcc params 0x014040c3 hci version 0x100 quirks 0x00000418
[ 1.086542] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.086623] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.086756] usb usb3: Product: xHCI Host Controller
[ 1.086835] usb usb3: Manufacturer: Linux 4.2.0-rc2+ xhci-hcd
[ 1.086915] usb usb3: SerialNumber: 0000:00:10.1
[ 1.087187] hub 3-0:1.0: USB hub found
[ 1.087271] hub 3-0:1.0: 2 ports detected
[ 1.087417] xhci_hcd 0000:00:10.1: xHCI Host Controller
[ 1.087531] xhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 4
[ 1.089694] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.089774] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.089906] usb usb4: Product: xHCI Host Controller
[ 1.089986] usb usb4: Manufacturer: Linux 4.2.0-rc2+ xhci-hcd
[ 1.090071] usb usb4: SerialNumber: 0000:00:10.1
[ 1.090328] hub 4-0:1.0: USB hub found
[ 1.090420] hub 4-0:1.0: 2 ports detected
[ 1.090601] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 1.090717] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 5
[ 1.150121] xhci_hcd 0000:03:00.0: hcc params 0x0200f180 hci version 0x96 quirks 0x00080000
[ 1.150403] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.150496] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.150633] usb usb5: Product: xHCI Host Controller
[ 1.150715] usb usb5: Manufacturer: Linux 4.2.0-rc2+ xhci-hcd
[ 1.150797] usb usb5: SerialNumber: 0000:03:00.0
[ 1.151061] hub 5-0:1.0: USB hub found
[ 1.151149] hub 5-0:1.0: 2 ports detected
[ 1.151296] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 1.151421] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 6
[ 1.151589] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.151673] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.151806] usb usb6: Product: xHCI Host Controller
[ 1.151885] usb usb6: Manufacturer: Linux 4.2.0-rc2+ xhci-hcd
[ 1.151971] usb usb6: SerialNumber: 0000:03:00.0
[ 1.152227] hub 6-0:1.0: USB hub found
[ 1.152312] hub 6-0:1.0: 2 ports detected
[ 1.152472] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.152555] ehci-pci: EHCI PCI platform driver
[ 1.152701] ehci-pci 0000:00:12.2: EHCI Host Controller
[ 1.152816] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 7
[ 1.152949] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.153088] ehci-pci 0000:00:12.2: debug port 1
[ 1.153199] ehci-pci 0000:00:12.2: irq 17, io mem 0xff76f000
[ 1.158464] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 1.158612] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.158696] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.158833] usb usb7: Product: EHCI Host Controller
[ 1.158916] usb usb7: Manufacturer: Linux 4.2.0-rc2+ ehci_hcd
[ 1.158999] usb usb7: SerialNumber: 0000:00:12.2
[ 1.159295] hub 7-0:1.0: USB hub found
[ 1.159400] hub 7-0:1.0: 5 ports detected
[ 1.159709] ehci-pci 0000:00:13.2: EHCI Host Controller
[ 1.159841] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 8
[ 1.159981] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.160126] ehci-pci 0000:00:13.2: debug port 1
[ 1.160238] ehci-pci 0000:00:13.2: irq 17, io mem 0xff76d000
[ 1.165460] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 1.165619] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.165703] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.165841] usb usb8: Product: EHCI Host Controller
[ 1.165924] usb usb8: Manufacturer: Linux 4.2.0-rc2+ ehci_hcd
[ 1.167838] usb usb8: SerialNumber: 0000:00:13.2
[ 1.168160] hub 8-0:1.0: USB hub found
[ 1.168246] hub 8-0:1.0: 5 ports detected
[ 1.168484] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.168571] ohci-pci: OHCI PCI platform driver
[ 1.168763] ohci-pci 0000:00:12.0: OHCI PCI host controller
[ 1.168918] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 9
[ 1.169081] ohci-pci 0000:00:12.0: irq 18, io mem 0xff770000
[ 1.223471] usb usb9: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.223559] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.223698] usb usb9: Product: OHCI PCI host controller
[ 1.223780] usb usb9: Manufacturer: Linux 4.2.0-rc2+ ohci_hcd
[ 1.223863] usb usb9: SerialNumber: 0000:00:12.0
[ 1.224172] hub 9-0:1.0: USB hub found
[ 1.224261] hub 9-0:1.0: 5 ports detected
[ 1.224574] ohci-pci 0000:00:13.0: OHCI PCI host controller
[ 1.224714] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 10
[ 1.224873] ohci-pci 0000:00:13.0: irq 18, io mem 0xff76e000
[ 1.279419] usb usb10: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.279507] usb usb10: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.279646] usb usb10: Product: OHCI PCI host controller
[ 1.279729] usb usb10: Manufacturer: Linux 4.2.0-rc2+ ohci_hcd
[ 1.279811] usb usb10: SerialNumber: 0000:00:13.0
[ 1.280125] hub 10-0:1.0: USB hub found
[ 1.280213] hub 10-0:1.0: 5 ports detected
[ 1.280529] ohci-pci 0000:00:14.5: OHCI PCI host controller
[ 1.280667] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 11
[ 1.280828] ohci-pci 0000:00:14.5: irq 18, io mem 0xff76c000
[ 1.335372] usb usb11: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.335460] usb usb11: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.335597] usb usb11: Product: OHCI PCI host controller
[ 1.335680] usb usb11: Manufacturer: Linux 4.2.0-rc2+ ohci_hcd
[ 1.335763] usb usb11: SerialNumber: 0000:00:14.5
[ 1.336083] hub 11-0:1.0: USB hub found
[ 1.336193] hub 11-0:1.0: 2 ports detected
[ 1.336382] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.336538] usbcore: registered new interface driver usbserial
[ 1.336628] usbcore: registered new interface driver usbserial_generic
[ 1.336717] usbserial: USB Serial support registered for generic
[ 1.336839] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 1.336922] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 1.337764] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.338046] mousedev: PS/2 mouse device common for all mice
[ 1.338337] rtc_cmos 00:05: RTC can wake from S4
[ 1.338530] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 1.338636] rtc_cmos 00:05: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.338839] device-mapper: uevent: version 1.0.3
[ 1.338985] device-mapper: ioctl: 4.32.0-ioctl (2015-6-26) initialised: dm-devel@redhat.com
[ 1.339308] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.339503] usbcore: registered new interface driver usbhid
[ 1.339585] usbhid: USB HID core driver
[ 1.339690] drop_monitor: Initializing network drop monitor service
[ 1.339836] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.339966] Initializing XFRM netlink socket
[ 1.340145] NET: Registered protocol family 10
[ 1.340446] mip6: Mobile IPv6
[ 1.340533] NET: Registered protocol family 17
[ 1.340915] AVX version of gcm_enc/dec engaged.
[ 1.340997] AES CTR mode by8 optimization enabled
[ 1.362291] Loading compiled-in X.509 certificates
[ 1.363093] Loaded X.509 cert 'Magrathea: Glacier signing key: 4a92f06a48b93d0e272e9a2b615aff0f01e0bbba'
[ 1.363268] registered taskstats version 1
[ 1.363670] Magic number: 7:317:543
[ 1.363827] rtc_cmos 00:05: setting system clock to 2015-07-27 17:32:49 UTC (1438018369)
[ 1.364038] PM: Hibernation image not present or could not be loaded.
[ 1.373113] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[ 1.386247] usb 1-1: new low-speed USB device number 2 using xhci_hcd
[ 1.535799] usb 1-1: New USB device found, idVendor=046d, idProduct=c030
[ 1.535888] usb 1-1: New USB device strings: Mfr=4, Product=32, SerialNumber=0
[ 1.536042] usb 1-1: Product: iFeel Mouse
[ 1.536125] usb 1-1: Manufacturer: Logitech Inc.
[ 1.536505] usb 1-1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 1.536651] usb 1-1: ep 0x1 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 1.540121] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.541084] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.552908] input: Logitech Inc. iFeel Mouse as /devices/pci0000:00/0000:00:10.0/usb1/1-1/1-1:1.0/0003:046D:C030.0001/input/input3
[ 1.552945] ata2.00: ATA-8: KINGSTON SV300S37A120G, 506ABBF0, max UDMA/133
[ 1.552947] ata2.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.553418] hid-generic 0003:046D:C030.0001: input,hidraw0: USB HID v1.00 Mouse [Logitech Inc. iFeel Mouse ] on usb-0000:00:10.0-1/input0
[ 1.562826] ata2.00: configured for UDMA/133
[ 1.584351] ata1.00: HPA detected: current 156299375, native 156301488
[ 1.584451] ata1.00: ATA-7: ST380815AS, 4.AAB, max UDMA/133
[ 1.584531] ata1.00: 156299375 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.642505] ata1.00: configured for UDMA/133
[ 1.642735] scsi 0:0:0:0: Direct-Access ATA ST380815AS B PQ: 0 ANSI: 5
[ 1.643101] sd 0:0:0:0: [sda] 156299375 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 1.643162] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.643301] scsi 1:0:0:0: Direct-Access ATA KINGSTON SV300S3 BBF0 PQ: 0 ANSI: 5
[ 1.643438] sd 1:0:0:0: [sdb] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 1.643457] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 1.643487] sd 1:0:0:0: [sdb] Write Protect is off
[ 1.643488] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.643516] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.644096] sd 0:0:0:0: [sda] Write Protect is off
[ 1.644183] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.644214] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.645786] sdb: sdb1
[ 1.646185] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 1.690907] sda: sda1
[ 1.691496] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.691986] Freeing unused kernel memory: 1520K (ffffffff81d2c000 - ffffffff81ea8000)
[ 1.692128] Write protecting the kernel read-only data: 12288k
[ 1.692569] Freeing unused kernel memory: 972K (ffff88000170d000 - ffff880001800000)
[ 1.692984] Freeing unused kernel memory: 876K (ffff880001b25000 - ffff880001c00000)
[ 1.695666] systemd[1]: systemd 204 running in system mode. (+PAM +LIBWRAP +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 1.695905] systemd[1]: Running in initial RAM disk.
[ 1.696414] systemd[1]: Set hostname to <cm>.
[ 1.696876] random: systemd urandom read with 17 bits of entropy available
[ 1.701414] systemd[1]: Expecting device dev-mapper-fedora\x2dswap.device...
[ 1.701718] systemd[1]: Expecting device dev-mapper-fedora\x2droot.device...
[ 1.702011] systemd[1]: Starting Timers.
[ 1.702332] systemd[1]: Reached target Timers.
[ 1.702446] systemd[1]: Starting Journal Socket.
[ 1.702808] systemd[1]: Listening on Journal Socket.
[ 1.703048] systemd[1]: Starting dracut cmdline hook...
[ 1.703776] systemd[1]: Starting Journal Service...
[ 1.704861] systemd[1]: Started Journal Service.
[ 1.705494] systemd[1]: Started Load Kernel Modules.
[ 1.705605] systemd[1]: Starting udev Kernel Socket.
[ 1.706012] systemd[1]: Listening on udev Kernel Socket.
[ 1.706137] systemd[1]: Starting udev Control Socket.
[ 1.706472] systemd[1]: Listening on udev Control Socket.
[ 1.706571] systemd[1]: Starting Sockets.
[ 1.706904] systemd[1]: Reached target Sockets.
[ 1.707004] systemd[1]: Starting Swap.
[ 1.707320] systemd[1]: Reached target Swap.
[ 1.707419] systemd[1]: Starting Local File Systems.
[ 1.707734] systemd[1]: Reached target Local File Systems.
[ 1.800726] systemd-udevd[218]: starting version 204
[ 1.830419] scsi host2: pata_atiixp
[ 1.832504] scsi host3: pata_atiixp
[ 1.832565] ata3: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf100 irq 14
[ 1.832566] ata4: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf108 irq 15
[ 2.047517] tsc: Refined TSC clocksource calibration: 3693.282 MHz
[ 2.047614] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x6a7918f751d, max_idle_ns: 881590915016 ns
[ 2.725506] random: nonblocking pool is initialized
[ 2.789015] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[ 2.967762] systemd-journald[131]: Received SIGTERM
[ 3.046935] clocksource: Switched to clocksource tsc
[ 3.839661] SELinux: Disabled at runtime.
[ 3.839761] SELinux: Unregistering netfilter hooks
[ 3.882908] audit: type=1404 audit(1438018372.020:2): selinux=0 auid=4294967295 ses=4294967295
[ 4.665591] LVM: Logical Volume autoactivation enabled.
[ 4.665596] LVM: Activation generator successfully completed.
[ 7.208447] systemd-udevd[406]: starting version 204
[ 7.946408] EXT4-fs (dm-0): re-mounted. Opts: (null)
[ 8.278126] acpi-cpufreq: overriding BIOS provided _PSD data
[ 8.766492] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 8.766680] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input4
[ 8.915219] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 8.915403] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb20
[ 8.969592] MCE: In-kernel MCE decoding enabled.
[ 9.153519] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[ 9.357064] EDAC MC: Ver: 3.0.0
[ 9.438498] AMD64 EDAC driver v3.4.0
[ 9.438654] EDAC amd64: DRAM ECC disabled.
[ 9.438749] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
(Note that use of the override may cause unknown side effects.)
[ 9.871703] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 9.899331] microcode: CPU0: patch_level=0x06003104
[ 10.010221] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 10.060419] microcode: CPU1: patch_level=0x06003104
[ 10.060540] microcode: CPU2: patch_level=0x06003104
[ 10.060655] microcode: CPU3: patch_level=0x06003104
[ 10.060860] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 10.548836] systemd-journald[399]: Received request to flush runtime journal from PID 1
[ 11.043578] alx 0000:04:00.0 eth0: Qualcomm Atheros AR816x/AR817x Ethernet [bc:5f:f4:f8:24:b7]
[ 12.612921] Adding 16703484k swap on /dev/mapper/fedora-swap. Priority:-1 extents:1 across:16703484k FS
[ 12.707099] alx 0000:04:00.0 em1: renamed from eth0
[ 12.711908] systemd-udevd[430]: renamed network interface eth0 to em1
[ 13.323691] audit: type=1305 audit(1438018381.469:3): audit_pid=470 old=0 auid=4294967295 ses=4294967295 res=1
[ 17.043296] snd_hda_intel 0000:00:01.1: Force to non-snoop mode
[ 17.828774] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.1/sound/card0/input6
[ 17.829005] input: HDA ATI HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.1/sound/card0/input7
[ 17.829221] input: HDA ATI HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.1/sound/card0/input8
[ 17.829417] input: HDA ATI HDMI HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.1/sound/card0/input9
[ 18.008308] snd_hda_codec_realtek hdaudioC1D0: ALC1150: SKU not ready 0x00000000
[ 18.008943] snd_hda_codec_realtek hdaudioC1D0: autoconfig for ALC1150: line_outs=3 (0x14/0x15/0x16/0x0/0x0) type:line
[ 18.009086] snd_hda_codec_realtek hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 18.009226] snd_hda_codec_realtek hdaudioC1D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 18.009364] snd_hda_codec_realtek hdaudioC1D0: mono: mono_out=0x0
[ 18.009447] snd_hda_codec_realtek hdaudioC1D0: dig-out=0x1e/0x0
[ 18.009530] snd_hda_codec_realtek hdaudioC1D0: inputs:
[ 18.009614] snd_hda_codec_realtek hdaudioC1D0: Front Mic=0x19
[ 18.009712] snd_hda_codec_realtek hdaudioC1D0: Rear Mic=0x18
[ 18.009796] snd_hda_codec_realtek hdaudioC1D0: Line=0x1a
[ 18.027048] input: HD-Audio Generic Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input10
[ 18.027298] input: HD-Audio Generic Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input11
[ 18.027497] input: HD-Audio Generic Line as /devices/pci0000:00/0000:00:14.2/sound/card1/input12
[ 18.027716] input: HD-Audio Generic Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card1/input13
[ 18.028664] input: HD-Audio Generic Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card1/input14
[ 18.028878] input: HD-Audio Generic Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card1/input15
[ 18.029078] input: HD-Audio Generic Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card1/input16
[ 18.536570] kvm: Nested Virtualization enabled
[ 18.536662] kvm: Nested Paging enabled
[ 20.835265] systemd-logind[516]: Watching system buttons on /dev/input/event1 (Power Button)
[ 20.835423] systemd-logind[516]: Watching system buttons on /dev/input/event4 (Video Bus)
[ 20.835549] systemd-logind[516]: Watching system buttons on /dev/input/event0 (Power Button)
[ 31.713236] IPv6: ADDRCONF(NETDEV_UP): em1: link is not ready
[ 31.714040] alx 0000:04:00.0 em1: NIC Up: 1 Gbps Full
[ 31.714294] IPv6: ADDRCONF(NETDEV_CHANGE): em1: link becomes ready
[ 31.841008] tun: Universal TUN/TAP device driver, 1.6
[ 31.841055] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 36.001084] Bluetooth: Core ver 2.20
[ 36.001136] NET: Registered protocol family 31
[ 36.001165] Bluetooth: HCI device and connection manager initialized
[ 36.001197] Bluetooth: HCI socket layer initialized
[ 36.001250] Bluetooth: L2CAP socket layer initialized
[ 36.001284] Bluetooth: SCO socket layer initialized
[ 36.182063] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 36.182103] Bluetooth: BNEP filters: protocol multicast
[ 36.182138] Bluetooth: BNEP socket layer initialized
[ 37.530555] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 40.882324] Ebtables v2.0 registered
[-- Attachment #5: dmesg.nointremap --]
[-- Type: application/octet-stream, Size: 59845 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.2.0-rc2+ (alex@cm) (gcc version 4.8.3 20140624 (Red Hat 4.8.3-1) (GCC) ) #793 SMP Mon Jul 27 12:17:07 EDT 2015
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.2.0-rc2+ root=/dev/mapper/fedora-root ro rd.lvm.lv=fedora/swap rd.md=0 rd.dm=0 vconsole.keymap=us rd.luks=0 vconsole.font=latarcyrheb-sun16 rd.lvm.lv=fedora/root LANG=en_US.UTF-8 nointremap modprobe.blacklist=amdgpu,radeon 3
[ 0.000000] tseg: 007f800000
[ 0.000000] x86/fpu: xstate_offset[2]: 0240, xstate_sizes[2]: 0100
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x01: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x02: 'SSE registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x04: 'AVX registers'
[ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 0x340 bytes, using 'standard' format.
[ 0.000000] x86/fpu: Using 'eager' FPU context switches.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009e7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009e800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007bc3afff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007bc3b000-0x000000007bc6afff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007bc6b000-0x000000007bf29fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007bf2a000-0x000000007bfe5fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007bfe6000-0x000000007e10afff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007e10b000-0x000000007e10bfff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007e10c000-0x000000007e311fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007e312000-0x000000007e467fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007e468000-0x000000007f02efff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007f02f000-0x000000007f071fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007f072000-0x000000007f7f0fff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007f7f1000-0x000000007f7fffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec01fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed40000-0x00000000fed44fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff800000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000043effffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: To Be Filled By O.E.M. To Be Filled By O.E.M./FM2A88X Extreme6+, BIOS P2.70 01/15/2014
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x43f000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF write-through
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-E7FFF uncachable
[ 0.000000] E8000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000000 mask FFFF80000000 write-back
[ 0.000000] 1 base 00007F800000 mask FFFFFF800000 uncachable
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 000000043f000000 aka 17392M
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WC UC- WT
[ 0.000000] e820: update [mem 0x7f800000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0x7f800 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000fd8a0-0x000fd8af] mapped at [ffff8800000fd8a0]
[ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x02016000, 0x02016fff] PGTABLE
[ 0.000000] BRK [0x02017000, 0x02017fff] PGTABLE
[ 0.000000] BRK [0x02018000, 0x02018fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x43ee00000-0x43effffff]
[ 0.000000] [mem 0x43ee00000-0x43effffff] page 2M
[ 0.000000] BRK [0x02019000, 0x02019fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x420000000-0x43edfffff]
[ 0.000000] [mem 0x420000000-0x43edfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x400000000-0x41fffffff]
[ 0.000000] [mem 0x400000000-0x41fffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x7bc3afff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x7bbfffff] page 2M
[ 0.000000] [mem 0x7bc00000-0x7bc3afff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x7bc6b000-0x7bf29fff]
[ 0.000000] [mem 0x7bc6b000-0x7bf29fff] page 4k
[ 0.000000] BRK [0x0201a000, 0x0201afff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x7e10b000-0x7e10bfff]
[ 0.000000] [mem 0x7e10b000-0x7e10bfff] page 4k
[ 0.000000] BRK [0x0201b000, 0x0201bfff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x7e312000-0x7e467fff]
[ 0.000000] [mem 0x7e312000-0x7e467fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x7f02f000-0x7f071fff]
[ 0.000000] [mem 0x7f02f000-0x7f071fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x7f7f1000-0x7f7fffff]
[ 0.000000] [mem 0x7f7f1000-0x7f7fffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x3ffffffff]
[ 0.000000] [mem 0x100000000-0x3ffffffff] page 1G
[ 0.000000] RAMDISK: [mem 0x33244000-0x35919fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F04A0 000024 (v02 ALASKA)
[ 0.000000] ACPI: XSDT 0x000000007BFAE080 00007C (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 0x000000007BFB40E8 00010C (v05 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has zero address or length: 0x0000000000000000/0x1 (20150619/tbfadt-654)
[ 0.000000] ACPI: DSDT 0x000000007BFAE190 005F58 (v02 ALASKA A M I 00000000 INTL 20051117)
[ 0.000000] ACPI: FACS 0x000000007BFDC080 000040
[ 0.000000] ACPI: APIC 0x000000007BFB41F8 00007E (v03 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FPDT 0x000000007BFB4278 000044 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: MCFG 0x000000007BFB42C0 00003C (v01 ALASKA A M I 01072009 MSFT 00010013)
[ 0.000000] ACPI: HPET 0x000000007BFB4300 000038 (v01 ALASKA A M I 01072009 AMI 00000005)
[ 0.000000] ACPI: AAFT 0x000000007BFB4338 0002F5 (v01 ALASKA OEMAAFT 01072009 MSFT 00000097)
[ 0.000000] ACPI: IVRS 0x000000007BFB4630 000078 (v02 AMD BANTRY 00000001 AMD 00000000)
[ 0.000000] ACPI: SSDT 0x000000007BFB46A8 000B9C (v01 AMD BANTRY 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 0x000000007BFB5248 00033B (v02 AMD BANTRY 00000002 MSFT 04000000)
[ 0.000000] ACPI: CRAT 0x000000007BFB5588 0005A0 (v01 AMD BANTRY 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 0x000000007BFB5B28 001115 (v01 AMD CPMCMN 00000001 INTL 20051117)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000043effffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x43efe6000-0x43eff9fff]
[ 0.000000] [ffffea0000000000-ffffea0010ffffff] PMD -> [ffff88042f600000-ffff88043e5fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000043effffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009dfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x000000007bc3afff]
[ 0.000000] node 0: [mem 0x000000007bc6b000-0x000000007bf29fff]
[ 0.000000] node 0: [mem 0x000000007e10b000-0x000000007e10bfff]
[ 0.000000] node 0: [mem 0x000000007e312000-0x000000007e467fff]
[ 0.000000] node 0: [mem 0x000000007f02f000-0x000000007f071fff]
[ 0.000000] node 0: [mem 0x000000007f7f1000-0x000000007f7fffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000043effffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000043effffff]
[ 0.000000] On node 0 totalpages: 3911744
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3997 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7875 pages used for memmap
[ 0.000000] DMA32 zone: 503971 pages, LIFO batch:31
[ 0.000000] Normal zone: 53184 pages used for memmap
[ 0.000000] Normal zone: 3403776 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 5, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] IOAPIC[1]: apic_id 6, version 33, address 0xfec01000, GSI 24-55
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10228210 base: 0xfed00000
[ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009efff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7bc3b000-0x7bc6afff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7bf2a000-0x7bfe5fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7bfe6000-0x7e10afff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7e10c000-0x7e311fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7e468000-0x7f02efff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7f072000-0x7f7f0fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7f800000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec01fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec02000-0xfec0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec10000-0xfec10fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec11000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed01000-0xfed3ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed40000-0xfed44fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed45000-0xfed7ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed80000-0xfed8ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed90000-0xff7fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff800000-0xffffffff]
[ 0.000000] e820: [mem 0x7f800000-0xfebfffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 33 pages/cpu @ffff88043ec00000 s95448 r8192 d31528 u524288
[ 0.000000] pcpu-alloc: s95448 r8192 d31528 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 3850600
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.2.0-rc2+ root=/dev/mapper/fedora-root ro rd.lvm.lv=fedora/swap rd.md=0 rd.dm=0 vconsole.keymap=us rd.luks=0 vconsole.font=latarcyrheb-sun16 rd.lvm.lv=fedora/root LANG=en_US.UTF-8 nointremap modprobe.blacklist=amdgpu,radeon 3
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Memory: 15278028K/15646976K available (7209K kernel code, 1195K rwdata, 3220K rodata, 1520K init, 1428K bss, 368948K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000] NR_IRQS:8448 nr_irqs:1000 16
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 3693.256 MHz processor
[ 0.000024] Calibrating delay loop (skipped), value calculated using timer frequency.. 7386.51 BogoMIPS (lpj=3693256)
[ 0.000185] pid_max: default: 32768 minimum: 301
[ 0.000269] ACPI: Core revision 20150619
[ 0.003531] ACPI: All ACPI Tables successfully acquired
[ 0.003683] Security Framework initialized
[ 0.003766] SELinux: Initializing.
[ 0.003852] SELinux: Starting in permissive mode
[ 0.004848] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.009381] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.011495] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.011593] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.012017] Initializing cgroup subsys blkio
[ 0.012099] Initializing cgroup subsys devices
[ 0.012180] Initializing cgroup subsys freezer
[ 0.012261] Initializing cgroup subsys net_cls
[ 0.012353] Initializing cgroup subsys perf_event
[ 0.012449] CPU: Physical Processor ID: 0
[ 0.012528] CPU: Processor Core ID: 0
[ 0.012608] mce: CPU supports 7 MCE banks
[ 0.012692] LVT offset 1 assigned for vector 0xf9
[ 0.012775] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512
[ 0.012855] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0
[ 0.013032] Freeing SMP alternatives memory: 28K (ffffffff81ea8000 - ffffffff81eaf000)
[ 0.022339] ftrace: allocating 27833 entries in 109 pages
[ 0.031438] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.143168] smpboot: CPU0: AMD A10-7850K APU with Radeon(TM) R7 Graphics (fam: 15, model: 30, stepping: 01)
[ 0.145033] Performance Events: Fam15h core perfctr, AMD PMU driver.
[ 0.145196] ... version: 0
[ 0.145276] ... bit width: 48
[ 0.145355] ... generic registers: 6
[ 0.145434] ... value mask: 0000ffffffffffff
[ 0.145514] ... max period: 00007fffffffffff
[ 0.145593] ... fixed-purpose events: 0
[ 0.145672] ... event mask: 000000000000003f
[ 0.146248] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.146441] x86: Booting SMP configuration:
[ 0.146520] .... node #0, CPUs: #1 #2 #3
[ 0.156159] x86: Booted up 1 node, 4 CPUs
[ 0.156322] smpboot: Total of 4 processors activated (29546.04 BogoMIPS)
[ 0.157086] devtmpfs: initialized
[ 0.157405] PM: Registering ACPI NVS region [mem 0x7bf2a000-0x7bfe5fff] (770048 bytes)
[ 0.157549] PM: Registering ACPI NVS region [mem 0x7e10c000-0x7e311fff] (2121728 bytes)
[ 0.157771] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.157985] atomic64_test: passed for x86-64 platform with CX8 and with SSE
[ 0.158069] pinctrl core: initialized pinctrl subsystem
[ 0.158194] RTC time: 17:22:50, date: 07/27/15
[ 0.158376] NET: Registered protocol family 16
[ 0.161164] cpuidle: using governor ladder
[ 0.165160] cpuidle: using governor menu
[ 0.165364] ACPI: bus type PCI registered
[ 0.165445] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.165607] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.165741] PCI: not using MMCONFIG
[ 0.165820] PCI: Using configuration type 1 for base access
[ 0.165905] PCI: Using configuration type 1 for extended access
[ 0.170520] ACPI: Added _OSI(Module Device)
[ 0.170606] ACPI: Added _OSI(Processor Device)
[ 0.170688] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.170770] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.172139] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.174317] ACPI: Interpreter enabled
[ 0.174407] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20150619/hwxface-580)
[ 0.174600] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150619/hwxface-580)
[ 0.174809] ACPI: (supports S0 S3 S4 S5)
[ 0.174891] ACPI: Using IOAPIC for interrupt routing
[ 0.175000] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.175173] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[ 0.175332] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.179534] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.179621] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.179909] acpi PNP0A03:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[ 0.180274] PCI host bridge to bus 0000:00
[ 0.180356] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.180437] pci_bus 0000:00: root bus resource [io 0x0000-0x03af window]
[ 0.180518] pci_bus 0000:00: root bus resource [io 0x03e0-0x0cf7 window]
[ 0.180599] pci_bus 0000:00: root bus resource [io 0x03b0-0x03df window]
[ 0.180686] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.180767] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.180900] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[ 0.181040] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff window]
[ 0.181180] pci 0000:00:00.0: [1022:1422] type 00 class 0x060000
[ 0.181263] pci 0000:00:00.2: [1022:1423] type 00 class 0x080600
[ 0.181346] pci 0000:00:01.0: [1002:130f] type 00 class 0x030000
[ 0.181360] pci 0000:00:01.0: reg 0x10: [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.181366] pci 0000:00:01.0: reg 0x18: [mem 0xd0000000-0xd07fffff 64bit pref]
[ 0.181370] pci 0000:00:01.0: reg 0x20: [io 0xf000-0xf0ff]
[ 0.181374] pci 0000:00:01.0: reg 0x24: [mem 0xff700000-0xff73ffff]
[ 0.181378] pci 0000:00:01.0: reg 0x30: [mem 0xff740000-0xff75ffff pref]
[ 0.181393] pci 0000:00:01.0: supports D1 D2
[ 0.181395] pci 0000:00:01.0: PME# supported from D1 D2 D3hot
[ 0.181458] pci 0000:00:01.1: [1002:1308] type 00 class 0x040300
[ 0.181471] pci 0000:00:01.1: reg 0x10: [mem 0xff764000-0xff767fff 64bit]
[ 0.181495] pci 0000:00:01.1: supports D1 D2
[ 0.181546] pci 0000:00:02.0: [1022:1424] type 00 class 0x060000
[ 0.181614] pci 0000:00:03.0: [1022:1424] type 00 class 0x060000
[ 0.181693] pci 0000:00:04.0: [1022:1424] type 00 class 0x060000
[ 0.181781] pci 0000:00:10.0: [1022:7814] type 00 class 0x0c0330
[ 0.181814] pci 0000:00:10.0: reg 0x10: [mem 0xff76a000-0xff76bfff 64bit]
[ 0.181877] pci 0000:00:10.0: PME# supported from D0 D3hot D3cold
[ 0.181914] pci 0000:00:10.0: System wakeup disabled by ACPI
[ 0.182042] pci 0000:00:10.1: [1022:7814] type 00 class 0x0c0330
[ 0.182075] pci 0000:00:10.1: reg 0x10: [mem 0xff768000-0xff769fff 64bit]
[ 0.182143] pci 0000:00:10.1: PME# supported from D0 D3hot D3cold
[ 0.182182] pci 0000:00:10.1: System wakeup disabled by ACPI
[ 0.182301] pci 0000:00:11.0: [1022:7801] type 00 class 0x010601
[ 0.182322] pci 0000:00:11.0: reg 0x10: [io 0xf190-0xf197]
[ 0.182329] pci 0000:00:11.0: reg 0x14: [io 0xf180-0xf183]
[ 0.182337] pci 0000:00:11.0: reg 0x18: [io 0xf170-0xf177]
[ 0.182344] pci 0000:00:11.0: reg 0x1c: [io 0xf160-0xf163]
[ 0.182351] pci 0000:00:11.0: reg 0x20: [io 0xf150-0xf15f]
[ 0.182358] pci 0000:00:11.0: reg 0x24: [mem 0xff771000-0xff7717ff]
[ 0.182431] pci 0000:00:12.0: [1022:7807] type 00 class 0x0c0310
[ 0.182443] pci 0000:00:12.0: reg 0x10: [mem 0xff770000-0xff770fff]
[ 0.182510] pci 0000:00:12.0: System wakeup disabled by ACPI
[ 0.182623] pci 0000:00:12.2: [1022:7808] type 00 class 0x0c0320
[ 0.182642] pci 0000:00:12.2: reg 0x10: [mem 0xff76f000-0xff76f0ff]
[ 0.182700] pci 0000:00:12.2: supports D1 D2
[ 0.182701] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.182731] pci 0000:00:12.2: System wakeup disabled by ACPI
[ 0.182845] pci 0000:00:13.0: [1022:7807] type 00 class 0x0c0310
[ 0.182857] pci 0000:00:13.0: reg 0x10: [mem 0xff76e000-0xff76efff]
[ 0.182925] pci 0000:00:13.0: System wakeup disabled by ACPI
[ 0.183043] pci 0000:00:13.2: [1022:7808] type 00 class 0x0c0320
[ 0.183063] pci 0000:00:13.2: reg 0x10: [mem 0xff76d000-0xff76d0ff]
[ 0.183113] pci 0000:00:13.2: supports D1 D2
[ 0.183114] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.183148] pci 0000:00:13.2: System wakeup disabled by ACPI
[ 0.183265] pci 0000:00:14.0: [1022:780b] type 00 class 0x0c0500
[ 0.183361] pci 0000:00:14.1: [1022:780c] type 00 class 0x01018a
[ 0.183373] pci 0000:00:14.1: reg 0x10: [io 0xf140-0xf147]
[ 0.183380] pci 0000:00:14.1: reg 0x14: [io 0xf130-0xf133]
[ 0.183387] pci 0000:00:14.1: reg 0x18: [io 0xf120-0xf127]
[ 0.183394] pci 0000:00:14.1: reg 0x1c: [io 0xf110-0xf113]
[ 0.183402] pci 0000:00:14.1: reg 0x20: [io 0xf100-0xf10f]
[ 0.183417] pci 0000:00:14.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.183498] pci 0000:00:14.1: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.183579] pci 0000:00:14.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.183662] pci 0000:00:14.1: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.183808] pci 0000:00:14.2: [1022:780d] type 00 class 0x040300
[ 0.183828] pci 0000:00:14.2: reg 0x10: [mem 0xff760000-0xff763fff 64bit]
[ 0.183871] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[ 0.183899] pci 0000:00:14.2: System wakeup disabled by ACPI
[ 0.184018] pci 0000:00:14.3: [1022:780e] type 00 class 0x060100
[ 0.184128] pci 0000:00:14.4: [1022:780f] type 01 class 0x060401
[ 0.184183] pci 0000:00:14.4: System wakeup disabled by ACPI
[ 0.184297] pci 0000:00:14.5: [1022:7809] type 00 class 0x0c0310
[ 0.184309] pci 0000:00:14.5: reg 0x10: [mem 0xff76c000-0xff76cfff]
[ 0.184377] pci 0000:00:14.5: System wakeup disabled by ACPI
[ 0.184493] pci 0000:00:15.0: [1022:43a0] type 01 class 0x060400
[ 0.184541] pci 0000:00:15.0: supports D1 D2
[ 0.184543] pci 0000:00:15.0: PME# supported from D0 D3hot D3cold
[ 0.184577] pci 0000:00:15.0: System wakeup disabled by ACPI
[ 0.184701] pci 0000:00:15.2: [1022:43a2] type 01 class 0x060400
[ 0.184749] pci 0000:00:15.2: supports D1 D2
[ 0.184750] pci 0000:00:15.2: PME# supported from D0 D3hot D3cold
[ 0.184783] pci 0000:00:15.2: System wakeup disabled by ACPI
[ 0.184899] pci 0000:00:15.3: [1022:43a3] type 01 class 0x060400
[ 0.184961] pci 0000:00:15.3: supports D1 D2
[ 0.184962] pci 0000:00:15.3: PME# supported from D0 D3hot D3cold
[ 0.184997] pci 0000:00:15.3: System wakeup disabled by ACPI
[ 0.185113] pci 0000:00:18.0: [1022:141a] type 00 class 0x060000
[ 0.185172] pci 0000:00:18.1: [1022:141b] type 00 class 0x060000
[ 0.185226] pci 0000:00:18.2: [1022:141c] type 00 class 0x060000
[ 0.185279] pci 0000:00:18.3: [1022:141d] type 00 class 0x060000
[ 0.185334] pci 0000:00:18.4: [1022:141e] type 00 class 0x060000
[ 0.185387] pci 0000:00:18.5: [1022:141f] type 00 class 0x060000
[ 0.185509] pci 0000:00:14.4: PCI bridge to [bus 01] (subtractive decode)
[ 0.185598] pci 0000:00:14.4: bridge window [io 0x0000-0x03af window] (subtractive decode)
[ 0.185600] pci 0000:00:14.4: bridge window [io 0x03e0-0x0cf7 window] (subtractive decode)
[ 0.185601] pci 0000:00:14.4: bridge window [io 0x03b0-0x03df window] (subtractive decode)
[ 0.185603] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode)
[ 0.185604] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[ 0.185606] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000dffff window] (subtractive decode)
[ 0.185607] pci 0000:00:14.4: bridge window [mem 0xc0000000-0xffffffff window] (subtractive decode)
[ 0.185649] pci 0000:00:15.0: PCI bridge to [bus 02]
[ 0.185797] pci 0000:03:00.0: [1b21:1042] type 00 class 0x0c0330
[ 0.185837] pci 0000:03:00.0: reg 0x10: [mem 0xff600000-0xff607fff 64bit]
[ 0.185936] pci 0000:03:00.0: PME# supported from D3hot D3cold
[ 0.187142] pci 0000:00:15.2: PCI bridge to [bus 03]
[ 0.187233] pci 0000:00:15.2: bridge window [mem 0xff600000-0xff6fffff]
[ 0.187311] pci 0000:04:00.0: [1969:10a1] type 00 class 0x020000
[ 0.187357] pci 0000:04:00.0: reg 0x10: [mem 0xff500000-0xff53ffff 64bit]
[ 0.187369] pci 0000:04:00.0: reg 0x18: [io 0xe000-0xe07f]
[ 0.187447] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.189144] pci 0000:00:15.3: PCI bridge to [bus 04]
[ 0.189236] pci 0000:00:15.3: bridge window [io 0xe000-0xefff]
[ 0.189239] pci 0000:00:15.3: bridge window [mem 0xff500000-0xff5fffff]
[ 0.189692] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 7 10 *11 14 15)
[ 0.190065] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 5 7 10 *11 14 15)
[ 0.190437] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 7 *10 11 14 15)
[ 0.190805] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 *5 7 10 11 14 15)
[ 0.191167] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 10 11 14 15) *0
[ 0.191540] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 10 11 14 15) *0
[ 0.191925] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 5 7 10 11 14 15) *0
[ 0.192299] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 7 10 11 14 15) *0
[ 0.192968] vgaarb: setting as boot device: PCI:0000:00:01.0
[ 0.193053] vgaarb: device added: PCI:0000:00:01.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.193200] vgaarb: loaded
[ 0.193282] vgaarb: bridge control possible 0000:00:01.0
[ 0.193437] SCSI subsystem initialized
[ 0.193578] libata version 3.00 loaded.
[ 0.193608] ACPI: bus type USB registered
[ 0.193706] usbcore: registered new interface driver usbfs
[ 0.193793] usbcore: registered new interface driver hub
[ 0.193888] usbcore: registered new device driver usb
[ 0.194069] PCI: Using ACPI for IRQ routing
[ 0.200660] PCI: pci_cache_line_size set to 64 bytes
[ 0.200716] e820: reserve RAM buffer [mem 0x0009e800-0x0009ffff]
[ 0.200718] e820: reserve RAM buffer [mem 0x7bc3b000-0x7bffffff]
[ 0.200719] e820: reserve RAM buffer [mem 0x7bf2a000-0x7bffffff]
[ 0.200720] e820: reserve RAM buffer [mem 0x7e10c000-0x7fffffff]
[ 0.200721] e820: reserve RAM buffer [mem 0x7e468000-0x7fffffff]
[ 0.200722] e820: reserve RAM buffer [mem 0x7f072000-0x7fffffff]
[ 0.200723] e820: reserve RAM buffer [mem 0x7f800000-0x7fffffff]
[ 0.200723] e820: reserve RAM buffer [mem 0x43f000000-0x43fffffff]
[ 0.200826] NetLabel: Initializing
[ 0.200913] NetLabel: domain hash size = 128
[ 0.200995] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.201085] NetLabel: unlabeled traffic allowed by default
[ 0.201236] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.201423] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 0.203548] clocksource: Switched to clocksource hpet
[ 0.210463] pnp: PnP ACPI init
[ 0.210665] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.210748] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.210807] system 00:01: [mem 0x80000000-0xbfffffff] has been reserved
[ 0.210889] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.210945] system 00:02: [mem 0xfeb80000-0xfebfffff] has been reserved
[ 0.211027] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.211111] system 00:03: [io 0x0290-0x029f] has been reserved
[ 0.211192] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.211288] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.211313] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.211355] system 00:06: [io 0x04d0-0x04d1] has been reserved
[ 0.211436] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.211467] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.211612] pnp 00:08: [dma 0 disabled]
[ 0.211648] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.211834] system 00:09: [io 0x04d0-0x04d1] has been reserved
[ 0.211915] system 00:09: [io 0x040b] has been reserved
[ 0.211996] system 00:09: [io 0x04d6] has been reserved
[ 0.212077] system 00:09: [io 0x0c00-0x0c01] has been reserved
[ 0.212157] system 00:09: [io 0x0c14] has been reserved
[ 0.212237] system 00:09: [io 0x0c50-0x0c51] has been reserved
[ 0.212318] system 00:09: [io 0x0c52] has been reserved
[ 0.212398] system 00:09: [io 0x0c6c] has been reserved
[ 0.212478] system 00:09: [io 0x0c6f] has been reserved
[ 0.212563] system 00:09: [io 0x0cd0-0x0cd1] has been reserved
[ 0.212643] system 00:09: [io 0x0cd2-0x0cd3] has been reserved
[ 0.212725] system 00:09: [io 0x0cd4-0x0cd5] has been reserved
[ 0.212806] system 00:09: [io 0x0cd6-0x0cd7] has been reserved
[ 0.212886] system 00:09: [io 0x0cd8-0x0cdf] has been reserved
[ 0.212967] system 00:09: [io 0x0800-0x089f] could not be reserved
[ 0.213047] system 00:09: [io 0x0b20-0x0b3f] has been reserved
[ 0.213128] system 00:09: [io 0x0900-0x090f] has been reserved
[ 0.213208] system 00:09: [io 0x0910-0x091f] has been reserved
[ 0.213289] system 00:09: [io 0xfe00-0xfefe] has been reserved
[ 0.213370] system 00:09: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.213451] system 00:09: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.213532] system 00:09: [mem 0xfed80000-0xfed8ffff] has been reserved
[ 0.213617] system 00:09: [mem 0xfed61000-0xfed70fff] has been reserved
[ 0.213698] system 00:09: [mem 0xfec10000-0xfec10fff] has been reserved
[ 0.213779] system 00:09: [mem 0xfed00000-0xfed00fff] could not be reserved
[ 0.213860] system 00:09: [mem 0xff800000-0xffffffff] has been reserved
[ 0.213941] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.214064] pnp: PnP ACPI: found 10 devices
[ 0.220661] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.220825] pci 0000:00:14.4: PCI bridge to [bus 01]
[ 0.220916] pci 0000:00:15.0: PCI bridge to [bus 02]
[ 0.221005] pci 0000:00:15.2: PCI bridge to [bus 03]
[ 0.221089] pci 0000:00:15.2: bridge window [mem 0xff600000-0xff6fffff]
[ 0.221176] pci 0000:00:15.3: PCI bridge to [bus 04]
[ 0.221259] pci 0000:00:15.3: bridge window [io 0xe000-0xefff]
[ 0.221344] pci 0000:00:15.3: bridge window [mem 0xff500000-0xff5fffff]
[ 0.221432] pci_bus 0000:00: resource 4 [io 0x0000-0x03af window]
[ 0.221433] pci_bus 0000:00: resource 5 [io 0x03e0-0x0cf7 window]
[ 0.221434] pci_bus 0000:00: resource 6 [io 0x03b0-0x03df window]
[ 0.221436] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff window]
[ 0.221437] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[ 0.221438] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[ 0.221440] pci_bus 0000:00: resource 10 [mem 0xc0000000-0xffffffff window]
[ 0.221442] pci_bus 0000:01: resource 4 [io 0x0000-0x03af window]
[ 0.221443] pci_bus 0000:01: resource 5 [io 0x03e0-0x0cf7 window]
[ 0.221444] pci_bus 0000:01: resource 6 [io 0x03b0-0x03df window]
[ 0.221445] pci_bus 0000:01: resource 7 [io 0x0d00-0xffff window]
[ 0.221447] pci_bus 0000:01: resource 8 [mem 0x000a0000-0x000bffff window]
[ 0.221448] pci_bus 0000:01: resource 9 [mem 0x000c0000-0x000dffff window]
[ 0.221449] pci_bus 0000:01: resource 10 [mem 0xc0000000-0xffffffff window]
[ 0.221451] pci_bus 0000:03: resource 1 [mem 0xff600000-0xff6fffff]
[ 0.221452] pci_bus 0000:04: resource 0 [io 0xe000-0xefff]
[ 0.221453] pci_bus 0000:04: resource 1 [mem 0xff500000-0xff5fffff]
[ 0.221482] NET: Registered protocol family 2
[ 0.221773] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.222204] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.222518] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.222666] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.222826] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.223025] NET: Registered protocol family 1
[ 0.223124] pci 0000:00:01.0: Video device with shadowed ROM
[ 0.461650] pci 0000:04:00.0: set MSI_INTX_DISABLE_BUG flag
[ 0.461740] PCI: CLS 64 bytes, default 64
[ 0.461810] Unpacking initramfs...
[ 0.971071] Freeing initrd memory: 39768K (ffff880033244000 - ffff88003591a000)
[ 1.051658] AMD-Vi: IOMMU performance counters supported
[ 1.051888] ERROR: Unable to locate IOAPIC for GSI 56
[ 1.051974] pci 0000:00:00.2: PCI INT A: failed to register GSI
[ 1.052795] iommu: Adding device 0000:00:00.0 to group 0
[ 1.053234] iommu: Adding device 0000:00:01.0 to group 1
[ 1.053329] iommu: Using direct mapping for device 0000:00:01.0
[ 1.053427] iommu: Adding device 0000:00:01.1 to group 1
[ 1.053812] iommu: Adding device 0000:00:02.0 to group 2
[ 1.054232] iommu: Adding device 0000:00:03.0 to group 3
[ 1.054650] iommu: Adding device 0000:00:04.0 to group 4
[ 1.055118] iommu: Adding device 0000:00:10.0 to group 5
[ 1.057004] iommu: Adding device 0000:00:10.1 to group 5
[ 1.057420] iommu: Adding device 0000:00:11.0 to group 6
[ 1.057855] iommu: Adding device 0000:00:12.0 to group 7
[ 1.057949] iommu: Adding device 0000:00:12.2 to group 7
[ 1.058381] iommu: Adding device 0000:00:13.0 to group 8
[ 1.058482] iommu: Adding device 0000:00:13.2 to group 8
[ 1.058917] iommu: Adding device 0000:00:14.0 to group 9
[ 1.059008] iommu: Adding device 0000:00:14.1 to group 9
[ 1.059101] iommu: Adding device 0000:00:14.2 to group 9
[ 1.059193] iommu: Adding device 0000:00:14.3 to group 9
[ 1.059605] iommu: Adding device 0000:00:14.4 to group 10
[ 1.060022] iommu: Adding device 0000:00:14.5 to group 11
[ 1.060452] iommu: Adding device 0000:00:15.0 to group 12
[ 1.060547] iommu: Adding device 0000:00:15.2 to group 12
[ 1.060642] iommu: Adding device 0000:00:15.3 to group 12
[ 1.061118] iommu: Adding device 0000:00:18.0 to group 13
[ 1.061211] iommu: Adding device 0000:00:18.1 to group 13
[ 1.061304] iommu: Adding device 0000:00:18.2 to group 13
[ 1.061397] iommu: Adding device 0000:00:18.3 to group 13
[ 1.061490] iommu: Adding device 0000:00:18.4 to group 13
[ 1.061582] iommu: Adding device 0000:00:18.5 to group 13
[ 1.061671] iommu: Adding device 0000:03:00.0 to group 12
[ 1.061772] iommu: Adding device 0000:04:00.0 to group 12
[ 1.061852] AMD-Vi: Found IOMMU at 0000:00:00.2 cap 0x40
[ 1.061932] AMD-Vi: Extended features: PPR GT IA PC
[ 1.062359] AMD-Vi: Lazy IO/TLB flushing enabled
[ 1.064490] perf: AMD NB counters detected
[ 1.064590] perf: amd_iommu: Detected. (2 banks, 4 counters/bank)
[ 1.064688] LVT offset 0 assigned for vector 0x400
[ 1.064785] perf: AMD IBS detected (0x000001ff)
[ 1.065417] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 1.065517] Initialise system trusted keyring
[ 1.065612] audit: initializing netlink subsys (disabled)
[ 1.065713] audit: type=2000 audit(1438017769.951:1): initialized
[ 1.066100] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.067724] VFS: Disk quotas dquot_6.6.0
[ 1.067844] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.068268] SELinux: Registering netfilter hooks
[ 1.071652] NET: Registered protocol family 38
[ 1.071760] Key type asymmetric registered
[ 1.071843] Asymmetric key parser 'x509' registered
[ 1.071955] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.072150] io scheduler noop registered
[ 1.072239] io scheduler deadline registered
[ 1.072370] io scheduler cfq registered (default)
[ 1.072910] pcieport 0000:00:15.0: Signaling PME through PCIe PME interrupt
[ 1.072996] pcie_pme 0000:00:15.0:pcie01: service driver pcie_pme loaded
[ 1.073014] pcieport 0000:00:15.2: Signaling PME through PCIe PME interrupt
[ 1.073097] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
[ 1.073182] pcie_pme 0000:00:15.2:pcie01: service driver pcie_pme loaded
[ 1.073198] pcieport 0000:00:15.3: Signaling PME through PCIe PME interrupt
[ 1.073281] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt
[ 1.073371] pcie_pme 0000:00:15.3:pcie01: service driver pcie_pme loaded
[ 1.073377] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.073464] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.073626] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 1.073779] ACPI: Power Button [PWRB]
[ 1.073897] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 1.074036] ACPI: Power Button [PWRF]
[ 1.074150] ACPI: acpi_idle registered with cpuidle
[ 1.074505] GHES: HEST is not enabled!
[ 1.074693] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.095311] 00:08: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 1.095997] Non-volatile memory driver v1.3
[ 1.096105] Linux agpgart interface v0.103
[ 1.097628] loop: module loaded
[ 1.097832] ahci 0000:00:11.0: version 3.0
[ 1.097998] ahci 0000:00:11.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[ 1.098139] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck led clo pmp pio slum part sxs
[ 1.098658] scsi host0: ahci
[ 1.098857] scsi host1: ahci
[ 1.098974] ata1: SATA max UDMA/133 abar m2048@0xff771000 port 0xff771100 irq 28
[ 1.099113] ata2: SATA max UDMA/133 abar m2048@0xff771000 port 0xff771180 irq 28
[ 1.099330] libphy: Fixed MDIO Bus: probed
[ 1.099548] QUIRK: Enable AMD PLL fix
[ 1.099558] xhci_hcd 0000:00:10.0: xHCI Host Controller
[ 1.099678] xhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 1.100012] xhci_hcd 0000:00:10.0: hcc params 0x014040c3 hci version 0x100 quirks 0x00000418
[ 1.100279] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.100363] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.100500] usb usb1: Product: xHCI Host Controller
[ 1.100583] usb usb1: Manufacturer: Linux 4.2.0-rc2+ xhci-hcd
[ 1.100665] usb usb1: SerialNumber: 0000:00:10.0
[ 1.100889] hub 1-0:1.0: USB hub found
[ 1.100977] hub 1-0:1.0: 2 ports detected
[ 1.101133] xhci_hcd 0000:00:10.0: xHCI Host Controller
[ 1.101248] xhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[ 1.103434] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.103518] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.103656] usb usb2: Product: xHCI Host Controller
[ 1.103749] usb usb2: Manufacturer: Linux 4.2.0-rc2+ xhci-hcd
[ 1.103835] usb usb2: SerialNumber: 0000:00:10.0
[ 1.104022] hub 2-0:1.0: USB hub found
[ 1.104109] hub 2-0:1.0: 2 ports detected
[ 1.104310] xhci_hcd 0000:00:10.1: xHCI Host Controller
[ 1.104428] xhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 1.104747] xhci_hcd 0000:00:10.1: hcc params 0x014040c3 hci version 0x100 quirks 0x00000418
[ 1.104986] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.105070] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.105207] usb usb3: Product: xHCI Host Controller
[ 1.105295] usb usb3: Manufacturer: Linux 4.2.0-rc2+ xhci-hcd
[ 1.105378] usb usb3: SerialNumber: 0000:00:10.1
[ 1.105645] hub 3-0:1.0: USB hub found
[ 1.105741] hub 3-0:1.0: 2 ports detected
[ 1.105885] xhci_hcd 0000:00:10.1: xHCI Host Controller
[ 1.106000] xhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 4
[ 1.108165] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.108249] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.108392] usb usb4: Product: xHCI Host Controller
[ 1.108474] usb usb4: Manufacturer: Linux 4.2.0-rc2+ xhci-hcd
[ 1.108557] usb usb4: SerialNumber: 0000:00:10.1
[ 1.108827] hub 4-0:1.0: USB hub found
[ 1.108911] hub 4-0:1.0: 2 ports detected
[ 1.109086] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 1.109199] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 5
[ 1.168605] xhci_hcd 0000:03:00.0: hcc params 0x0200f180 hci version 0x96 quirks 0x00080000
[ 1.168864] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.168947] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.169084] usb usb5: Product: xHCI Host Controller
[ 1.169167] usb usb5: Manufacturer: Linux 4.2.0-rc2+ xhci-hcd
[ 1.169250] usb usb5: SerialNumber: 0000:03:00.0
[ 1.169513] hub 5-0:1.0: USB hub found
[ 1.169600] hub 5-0:1.0: 2 ports detected
[ 1.169754] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 1.169872] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 6
[ 1.170040] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.170124] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.170262] usb usb6: Product: xHCI Host Controller
[ 1.170344] usb usb6: Manufacturer: Linux 4.2.0-rc2+ xhci-hcd
[ 1.170432] usb usb6: SerialNumber: 0000:03:00.0
[ 1.170706] hub 6-0:1.0: USB hub found
[ 1.170793] hub 6-0:1.0: 2 ports detected
[ 1.170943] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.171028] ehci-pci: EHCI PCI platform driver
[ 1.171177] ehci-pci 0000:00:12.2: EHCI Host Controller
[ 1.171394] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 7
[ 1.171534] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.171697] ehci-pci 0000:00:12.2: debug port 1
[ 1.171808] ehci-pci 0000:00:12.2: irq 17, io mem 0xff76f000
[ 1.177773] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 1.177926] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.178008] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.178141] usb usb7: Product: EHCI Host Controller
[ 1.178220] usb usb7: Manufacturer: Linux 4.2.0-rc2+ ehci_hcd
[ 1.178300] usb usb7: SerialNumber: 0000:00:12.2
[ 1.178603] hub 7-0:1.0: USB hub found
[ 1.178699] hub 7-0:1.0: 5 ports detected
[ 1.179008] ehci-pci 0000:00:13.2: EHCI Host Controller
[ 1.179138] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 8
[ 1.179273] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.179413] ehci-pci 0000:00:13.2: debug port 1
[ 1.179524] ehci-pci 0000:00:13.2: irq 17, io mem 0xff76d000
[ 1.184760] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 1.184908] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.184992] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.185130] usb usb8: Product: EHCI Host Controller
[ 1.185211] usb usb8: Manufacturer: Linux 4.2.0-rc2+ ehci_hcd
[ 1.185294] usb usb8: SerialNumber: 0000:00:13.2
[ 1.187368] hub 8-0:1.0: USB hub found
[ 1.187456] hub 8-0:1.0: 5 ports detected
[ 1.187672] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.187761] ohci-pci: OHCI PCI platform driver
[ 1.187951] ohci-pci 0000:00:12.0: OHCI PCI host controller
[ 1.188083] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 9
[ 1.188249] ohci-pci 0000:00:12.0: irq 18, io mem 0xff770000
[ 1.242776] usb usb9: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.242864] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.243003] usb usb9: Product: OHCI PCI host controller
[ 1.243085] usb usb9: Manufacturer: Linux 4.2.0-rc2+ ohci_hcd
[ 1.243168] usb usb9: SerialNumber: 0000:00:12.0
[ 1.243608] hub 9-0:1.0: USB hub found
[ 1.243701] hub 9-0:1.0: 5 ports detected
[ 1.244003] ohci-pci 0000:00:13.0: OHCI PCI host controller
[ 1.244180] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 10
[ 1.244342] ohci-pci 0000:00:13.0: irq 18, io mem 0xff76e000
[ 1.298717] usb usb10: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.298805] usb usb10: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.298943] usb usb10: Product: OHCI PCI host controller
[ 1.299026] usb usb10: Manufacturer: Linux 4.2.0-rc2+ ohci_hcd
[ 1.299109] usb usb10: SerialNumber: 0000:00:13.0
[ 1.299421] hub 10-0:1.0: USB hub found
[ 1.299509] hub 10-0:1.0: 5 ports detected
[ 1.299824] ohci-pci 0000:00:14.5: OHCI PCI host controller
[ 1.299967] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 11
[ 1.300126] ohci-pci 0000:00:14.5: irq 18, io mem 0xff76c000
[ 1.354674] usb usb11: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.354762] usb usb11: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.354902] usb usb11: Product: OHCI PCI host controller
[ 1.354984] usb usb11: Manufacturer: Linux 4.2.0-rc2+ ohci_hcd
[ 1.355066] usb usb11: SerialNumber: 0000:00:14.5
[ 1.355390] hub 11-0:1.0: USB hub found
[ 1.355499] hub 11-0:1.0: 2 ports detected
[ 1.355693] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.355848] usbcore: registered new interface driver usbserial
[ 1.355938] usbcore: registered new interface driver usbserial_generic
[ 1.356026] usbserial: USB Serial support registered for generic
[ 1.356152] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 1.356234] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 1.357078] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.357351] mousedev: PS/2 mouse device common for all mice
[ 1.357628] rtc_cmos 00:05: RTC can wake from S4
[ 1.357818] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 1.357920] rtc_cmos 00:05: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.358121] device-mapper: uevent: version 1.0.3
[ 1.358272] device-mapper: ioctl: 4.32.0-ioctl (2015-6-26) initialised: dm-devel@redhat.com
[ 1.358598] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.358790] usbcore: registered new interface driver usbhid
[ 1.358869] usbhid: USB HID core driver
[ 1.358971] drop_monitor: Initializing network drop monitor service
[ 1.359117] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.359246] Initializing XFRM netlink socket
[ 1.359423] NET: Registered protocol family 10
[ 1.359705] mip6: Mobile IPv6
[ 1.359788] NET: Registered protocol family 17
[ 1.360160] AVX version of gcm_enc/dec engaged.
[ 1.360240] AES CTR mode by8 optimization enabled
[ 1.383300] Loading compiled-in X.509 certificates
[ 1.384120] Loaded X.509 cert 'Magrathea: Glacier signing key: 4a92f06a48b93d0e272e9a2b615aff0f01e0bbba'
[ 1.384274] registered taskstats version 1
[ 1.384700] Magic number: 7:661:391
[ 1.384791] usb usb9: hash matches
[ 1.384877] hub 3-0:1.0: hash matches
[ 1.385019] rtc_cmos 00:05: setting system clock to 2015-07-27 17:22:51 UTC (1438017771)
[ 1.385232] PM: Hibernation image not present or could not be loaded.
[ 1.393657] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[ 1.405540] usb 1-1: new low-speed USB device number 2 using xhci_hcd
[ 1.557310] usb 1-1: New USB device found, idVendor=046d, idProduct=c030
[ 1.557398] usb 1-1: New USB device strings: Mfr=4, Product=32, SerialNumber=0
[ 1.557538] usb 1-1: Product: iFeel Mouse
[ 1.557621] usb 1-1: Manufacturer: Logitech Inc.
[ 1.557928] usb 1-1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 1.558070] usb 1-1: ep 0x1 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 1.558317] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.558428] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.570391] ata2.00: ATA-8: KINGSTON SV300S37A120G, 506ABBF0, max UDMA/133
[ 1.570480] ata2.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.574548] input: Logitech Inc. iFeel Mouse as /devices/pci0000:00/0000:00:10.0/usb1/1-1/1-1:1.0/0003:046D:C030.0001/input/input3
[ 1.574876] hid-generic 0003:046D:C030.0001: input,hidraw0: USB HID v1.00 Mouse [Logitech Inc. iFeel Mouse ] on usb-0000:00:10.0-1/input0
[ 1.580269] ata2.00: configured for UDMA/133
[ 1.601383] ata1.00: HPA detected: current 156299375, native 156301488
[ 1.601482] ata1.00: ATA-7: ST380815AS, 4.AAB, max UDMA/133
[ 1.601564] ata1.00: 156299375 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.659641] ata1.00: configured for UDMA/133
[ 1.659972] scsi 0:0:0:0: Direct-Access ATA ST380815AS B PQ: 0 ANSI: 5
[ 1.660305] sd 0:0:0:0: [sda] 156299375 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 1.660368] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.660513] scsi 1:0:0:0: Direct-Access ATA KINGSTON SV300S3 BBF0 PQ: 0 ANSI: 5
[ 1.660644] sd 1:0:0:0: [sdb] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 1.660664] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 1.660694] sd 1:0:0:0: [sdb] Write Protect is off
[ 1.660695] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.660721] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.661295] sd 0:0:0:0: [sda] Write Protect is off
[ 1.661384] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.661415] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.663206] sdb: sdb1
[ 1.663606] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 1.707938] sda: sda1
[ 1.708445] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.708925] Freeing unused kernel memory: 1520K (ffffffff81d2c000 - ffffffff81ea8000)
[ 1.709062] Write protecting the kernel read-only data: 12288k
[ 1.709600] Freeing unused kernel memory: 972K (ffff88000170d000 - ffff880001800000)
[ 1.710013] Freeing unused kernel memory: 876K (ffff880001b25000 - ffff880001c00000)
[ 1.712860] systemd[1]: systemd 204 running in system mode. (+PAM +LIBWRAP +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 1.713066] systemd[1]: Running in initial RAM disk.
[ 1.713588] systemd[1]: Set hostname to <cm>.
[ 1.714047] random: systemd urandom read with 17 bits of entropy available
[ 1.718110] systemd[1]: Expecting device dev-mapper-fedora\x2dswap.device...
[ 1.718419] systemd[1]: Expecting device dev-mapper-fedora\x2droot.device...
[ 1.718685] systemd[1]: Starting Timers.
[ 1.719014] systemd[1]: Reached target Timers.
[ 1.719118] systemd[1]: Starting Journal Socket.
[ 1.719507] systemd[1]: Listening on Journal Socket.
[ 1.719706] systemd[1]: Starting dracut cmdline hook...
[ 1.720415] systemd[1]: Starting Journal Service...
[ 1.721309] systemd[1]: Started Journal Service.
[ 1.721634] systemd[1]: Started Load Kernel Modules.
[ 1.721747] systemd[1]: Starting udev Kernel Socket.
[ 1.722085] systemd[1]: Listening on udev Kernel Socket.
[ 1.722266] systemd[1]: Starting udev Control Socket.
[ 1.722623] systemd[1]: Listening on udev Control Socket.
[ 1.722732] systemd[1]: Starting Sockets.
[ 1.723066] systemd[1]: Reached target Sockets.
[ 1.723194] systemd[1]: Starting Swap.
[ 1.723539] systemd[1]: Reached target Swap.
[ 1.723646] systemd[1]: Starting Local File Systems.
[ 1.723974] systemd[1]: Reached target Local File Systems.
[ 1.813635] systemd-udevd[218]: starting version 204
[ 1.846753] scsi host2: pata_atiixp
[ 1.846931] scsi host3: pata_atiixp
[ 1.847100] ata3: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf100 irq 14
[ 1.847183] ata4: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf108 irq 15
[ 2.064910] tsc: Refined TSC clocksource calibration: 3693.284 MHz
[ 2.064998] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x6a791bbbda0, max_idle_ns: 881590828579 ns
[ 2.734982] random: nonblocking pool is initialized
[ 2.806032] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[ 2.978507] systemd-journald[131]: Received SIGTERM
[ 3.064229] clocksource: Switched to clocksource tsc
[ 3.865017] SELinux: Disabled at runtime.
[ 3.865140] SELinux: Unregistering netfilter hooks
[ 3.908204] audit: type=1404 audit(1438017774.024:2): selinux=0 auid=4294967295 ses=4294967295
[ 4.740998] LVM: Logical Volume autoactivation enabled.
[ 4.741003] LVM: Activation generator successfully completed.
[ 7.334253] systemd-udevd[423]: starting version 204
[ 7.408967] EXT4-fs (dm-0): re-mounted. Opts: (null)
[ 8.128768] acpi-cpufreq: overriding BIOS provided _PSD data
[ 8.917643] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 8.917822] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input4
[ 8.953389] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[ 9.107704] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 9.107903] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb20
[ 9.233959] microcode: CPU0: patch_level=0x06003104
[ 9.286828] microcode: CPU1: patch_level=0x06003104
[ 9.286938] microcode: CPU2: patch_level=0x06003104
[ 9.287065] microcode: CPU3: patch_level=0x06003104
[ 9.287271] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 9.548473] MCE: In-kernel MCE decoding enabled.
[ 9.726432] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 9.771013] EDAC MC: Ver: 3.0.0
[ 9.830751] AMD64 EDAC driver v3.4.0
[ 9.830882] EDAC amd64: DRAM ECC disabled.
[ 9.830976] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
(Note that use of the override may cause unknown side effects.)
[ 9.911644] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 10.506914] alx 0000:04:00.0 eth0: Qualcomm Atheros AR816x/AR817x Ethernet [bc:5f:f4:f8:24:b7]
[ 11.065318] systemd-journald[398]: Received request to flush runtime journal from PID 1
[ 12.407992] alx 0000:04:00.0 em1: renamed from eth0
[ 12.414423] systemd-udevd[431]: renamed network interface eth0 to em1
[ 12.588783] Adding 16703484k swap on /dev/mapper/fedora-swap. Priority:-1 extents:1 across:16703484k FS
[ 12.816602] audit: type=1305 audit(1438017782.940:3): audit_pid=481 old=0 auid=4294967295 ses=4294967295 res=1
[ 16.355084] snd_hda_intel 0000:00:01.1: Force to non-snoop mode
[ 16.764504] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.1/sound/card0/input6
[ 16.764863] input: HDA ATI HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.1/sound/card0/input7
[ 16.765175] input: HDA ATI HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.1/sound/card0/input8
[ 16.765490] input: HDA ATI HDMI HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.1/sound/card0/input9
[ 17.007082] kvm: Nested Virtualization enabled
[ 17.007178] kvm: Nested Paging enabled
[ 17.251490] snd_hda_codec_realtek hdaudioC1D0: ALC1150: SKU not ready 0x00000000
[ 17.252120] snd_hda_codec_realtek hdaudioC1D0: autoconfig for ALC1150: line_outs=3 (0x14/0x15/0x16/0x0/0x0) type:line
[ 17.252262] snd_hda_codec_realtek hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 17.252401] snd_hda_codec_realtek hdaudioC1D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 17.252538] snd_hda_codec_realtek hdaudioC1D0: mono: mono_out=0x0
[ 17.252626] snd_hda_codec_realtek hdaudioC1D0: dig-out=0x1e/0x0
[ 17.252709] snd_hda_codec_realtek hdaudioC1D0: inputs:
[ 17.252792] snd_hda_codec_realtek hdaudioC1D0: Front Mic=0x19
[ 17.252874] snd_hda_codec_realtek hdaudioC1D0: Rear Mic=0x18
[ 17.252957] snd_hda_codec_realtek hdaudioC1D0: Line=0x1a
[ 17.270093] input: HD-Audio Generic Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input10
[ 17.270343] input: HD-Audio Generic Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input11
[ 17.270560] input: HD-Audio Generic Line as /devices/pci0000:00/0000:00:14.2/sound/card1/input12
[ 17.270865] input: HD-Audio Generic Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card1/input13
[ 17.271058] input: HD-Audio Generic Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card1/input14
[ 17.272112] input: HD-Audio Generic Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card1/input15
[ 17.272737] input: HD-Audio Generic Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card1/input16
[ 19.570717] systemd-logind[514]: Watching system buttons on /dev/input/event1 (Power Button)
[ 19.570878] systemd-logind[514]: Watching system buttons on /dev/input/event4 (Video Bus)
[ 19.571020] systemd-logind[514]: Watching system buttons on /dev/input/event0 (Power Button)
[ 31.180792] IPv6: ADDRCONF(NETDEV_UP): em1: link is not ready
[ 31.181585] alx 0000:04:00.0 em1: NIC Up: 1 Gbps Full
[ 31.181920] IPv6: ADDRCONF(NETDEV_CHANGE): em1: link becomes ready
[ 32.651816] tun: Universal TUN/TAP device driver, 1.6
[ 32.651851] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 33.856346] Bluetooth: Core ver 2.20
[ 33.856394] NET: Registered protocol family 31
[ 33.856424] Bluetooth: HCI device and connection manager initialized
[ 33.856456] Bluetooth: HCI socket layer initialized
[ 33.856487] Bluetooth: L2CAP socket layer initialized
[ 33.856521] Bluetooth: SCO socket layer initialized
[ 34.405658] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 34.405699] Bluetooth: BNEP filters: protocol multicast
[ 34.405743] Bluetooth: BNEP socket layer initialized
[ 37.932658] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 39.931266] Ebtables v2.0 registered
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: ATA failure regression in kernel 4.2
2015-07-27 16:30 ` Jiang Liu
2015-07-27 17:36 ` Alex Deucher
@ 2015-07-28 18:19 ` Alex Deucher
2015-07-28 18:37 ` Alexander Holler
1 sibling, 1 reply; 15+ messages in thread
From: Alex Deucher @ 2015-07-28 18:19 UTC (permalink / raw)
To: Jiang Liu; +Cc: Tejun Heo, LKML
On Mon, Jul 27, 2015 at 12:30 PM, Jiang Liu <jiang.liu@linux.intel.com> wrote:
> On 2015/7/27 23:21, Alex Deucher wrote:
>> On Sun, Jul 26, 2015 at 11:01 PM, Jiang Liu <jiang.liu@linux.intel.com> wrote:
>>> On 2015/7/25 1:38, Alex Deucher wrote:
>>>> On Thu, Jul 23, 2015 at 2:44 PM, Alex Deucher <alexdeucher@gmail.com> wrote:
>>>>> On Thu, Jul 23, 2015 at 2:35 PM, Tejun Heo <tj@kernel.org> wrote:
>>>>>> Hello,
>>>>>>
>>>>>> On Thu, Jul 23, 2015 at 01:48:24PM -0400, Alex Deucher wrote:
>>>>>>> Something new in kernel 4.2 seems to have broken one of my hard drives
>>>>>>> (ssd) in kernel 4.2. 4.1 and older kernels work fine. Here are the
>>>>>>> relevant logs.
>>>>>>>
>>>>>> ...
>>>>>>> [ 6.547628] ata2.00: qc timeout (cmd 0xec)
>>>>>>> [ 6.547721] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>>>>> [ 7.007213] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
>>>>>>> [ 16.997819] ata2.00: qc timeout (cmd 0xec)
>>>>>>> [ 16.997910] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>>>>> [ 16.997995] ata2: limiting SATA link speed to 3.0 Gbps
>>>>>>> [ 17.457400] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
>>>>>>> [ 47.429257] ata2.00: qc timeout (cmd 0xec)
>>>>>>> [ 47.429349] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>>>>> [ 47.888822] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
>>>>>>
>>>>>> Nothing really rings a bell. Timeouts on IDENTIFY. Could be IRQ
>>>>>> related. Which controller is it (lspci -nn)? Also, can you try to
>>>>>> bisect the issue?
>>>>>
>>>>> 00:11.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD] FCH
>>>>> SATA Controller [AHCI mode] [1022:7801] (rev 40)
>>>>> 00:14.1 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD] FCH
>>>>> IDE Controller [1022:780c]
>>>>>
>>>>> I can take a look at bisecting later this week.
>>>>
>>>> You were right about the interrupts. This is an AMD Kaveri APU system.
>>> Hi Alex,
>>> Could you please help to provide more information about the
>>> system so we could identify the issue? Dmesg and /proc/interrupts
>>> from good and bad kernels are welcomed.
>>> Thanks!
>>> Gerry
>>
>> See attached. Thanks!
> Hi Alex,
> Thanks for the info. Seems something is wrong with multiple-MSI
> support. To narrow down the scope, could you please help to:
I'm also not getting interrupts in my gpu driver. I haven't bisected
this specifically, but I suspect it is related since it to used to
work in 4.1. Whether I enable MSIs or not in my driver, I get a huge
numbers of interrupts on all CPUs as soon as the driver is loaded, but
the driver isr never gets called. E.g.,
49: 117757835 117763227 117787837 117868913 PCI-MSI
524288-edge amdgpu
nointremap doesn't seem to help.
Alex
> 1) apply the small patch and retest
> diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
> index 7e62751abfac..35f524cc23b7 100644
> --- a/drivers/ata/ahci.c
> +++ b/drivers/ata/ahci.c
> @@ -1345,6 +1345,7 @@ static int ahci_init_msi(struct pci_dev *pdev,
> unsigned int n_ports,
> if (nvec < 0)
> return nvec;
>
> + nvec = 1;
> /*
> * If number of MSIs is less than number of ports then Sharing Last
> * Message mode could be enforced. In this case assume that
> advantage
> 2) Disable interrupt remapping by kernel parameter "nointremap"
> and retest.
> Thanks!
> Gerry
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: ATA failure regression in kernel 4.2
2015-07-28 18:19 ` Alex Deucher
@ 2015-07-28 18:37 ` Alexander Holler
2015-07-30 17:01 ` Jiang Liu
2015-07-31 10:38 ` ATA failure regression in kernel 4.2 Alexander Holler
0 siblings, 2 replies; 15+ messages in thread
From: Alexander Holler @ 2015-07-28 18:37 UTC (permalink / raw)
To: Alex Deucher, Jiang Liu; +Cc: Tejun Heo, LKML
Am 28.07.2015 um 20:19 schrieb Alex Deucher:
> On Mon, Jul 27, 2015 at 12:30 PM, Jiang Liu <jiang.liu@linux.intel.com> wrote:
>> On 2015/7/27 23:21, Alex Deucher wrote:
>>> On Sun, Jul 26, 2015 at 11:01 PM, Jiang Liu <jiang.liu@linux.intel.com> wrote:
>>>> On 2015/7/25 1:38, Alex Deucher wrote:
>>>>> On Thu, Jul 23, 2015 at 2:44 PM, Alex Deucher <alexdeucher@gmail.com> wrote:
>>>>>> On Thu, Jul 23, 2015 at 2:35 PM, Tejun Heo <tj@kernel.org> wrote:
>>>>>>> Hello,
>>>>>>>
>>>>>>> On Thu, Jul 23, 2015 at 01:48:24PM -0400, Alex Deucher wrote:
>>>>>>>> Something new in kernel 4.2 seems to have broken one of my hard drives
>>>>>>>> (ssd) in kernel 4.2. 4.1 and older kernels work fine. Here are the
>>>>>>>> relevant logs.
>>>>>>>>
>>>>>>> ...
>>>>>>>> [ 6.547628] ata2.00: qc timeout (cmd 0xec)
>>>>>>>> [ 6.547721] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>>>>>> [ 7.007213] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
>>>>>>>> [ 16.997819] ata2.00: qc timeout (cmd 0xec)
>>>>>>>> [ 16.997910] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>>>>>> [ 16.997995] ata2: limiting SATA link speed to 3.0 Gbps
>>>>>>>> [ 17.457400] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
>>>>>>>> [ 47.429257] ata2.00: qc timeout (cmd 0xec)
>>>>>>>> [ 47.429349] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
>>>>>>>> [ 47.888822] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
>>>>>>>
>>>>>>> Nothing really rings a bell. Timeouts on IDENTIFY. Could be IRQ
>>>>>>> related. Which controller is it (lspci -nn)? Also, can you try to
>>>>>>> bisect the issue?
>>>>>>
>>>>>> 00:11.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD] FCH
>>>>>> SATA Controller [AHCI mode] [1022:7801] (rev 40)
>>>>>> 00:14.1 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD] FCH
>>>>>> IDE Controller [1022:780c]
>>>>>>
>>>>>> I can take a look at bisecting later this week.
>>>>>
>>>>> You were right about the interrupts. This is an AMD Kaveri APU system.
>>>> Hi Alex,
>>>> Could you please help to provide more information about the
>>>> system so we could identify the issue? Dmesg and /proc/interrupts
>>>> from good and bad kernels are welcomed.
>>>> Thanks!
>>>> Gerry
>>>
>>> See attached. Thanks!
>> Hi Alex,
>> Thanks for the info. Seems something is wrong with multiple-MSI
>> support. To narrow down the scope, could you please help to:
>
> I'm also not getting interrupts in my gpu driver. I haven't bisected
> this specifically, but I suspect it is related since it to used to
> work in 4.1. Whether I enable MSIs or not in my driver, I get a huge
> numbers of interrupts on all CPUs as soon as the driver is loaded, but
> the driver isr never gets called. E.g.,
> 49: 117757835 117763227 117787837 117868913 PCI-MSI
> 524288-edge amdgpu
> nointremap doesn't seem to help.
Same problem here with the AMD SATA controller (1022:7801). It failed to
identify the second disk when using 4.2-rc4.
nointremap helped, nothing else tested
Regards,
Alexander Holler
^ permalink raw reply [flat|nested] 15+ messages in thread
* [Debug Patch] Collect more information about the regression
@ 2015-07-30 17:01 ` Jiang Liu
0 siblings, 0 replies; 15+ messages in thread
From: Jiang Liu @ 2015-07-30 17:01 UTC (permalink / raw)
To: Thomas Gleixner, Alexander Holler, Mark Rustad, Alex Deucher,
Joerg Roedel
Cc: Jiang Liu, Tony Luck, Tejun Heo, linux-kernel, x86, iommu
Hi Alexander, Mark, Alex,
Could you please help to apply the debug patch and send me back
the dmesg? Please also help to turn kernel paramemter "apic=debug".
Hi Mark,
It seems that this regression is caused by support of multiple-MSI,
but I have no PCI card supportting multiple-MSI at hand. So may I remotely
access your system from Intel internal network? That will definitely speed
up fix.
Thanks!
Gerry
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
---
drivers/iommu/amd_iommu.c | 15 +++++++++++++--
drivers/iommu/intel_irq_remapping.c | 4 ++++
2 files changed, 17 insertions(+), 2 deletions(-)
diff --git a/drivers/iommu/amd_iommu.c b/drivers/iommu/amd_iommu.c
index a57e9b749895..c039ed9333a4 100644
--- a/drivers/iommu/amd_iommu.c
+++ b/drivers/iommu/amd_iommu.c
@@ -3916,8 +3916,8 @@ static void irq_remapping_prepare_irte(struct amd_ir_data *data,
union irte *irte = &data->irte_entry;
struct IO_APIC_route_entry *entry;
- data->irq_2_irte.devid = devid;
- data->irq_2_irte.index = index + sub_handle;
+ irte_info->devid = devid;
+ irte_info->index = index + sub_handle;
/* Setup IRTE for IOMMU */
irte->val = 0;
@@ -3926,6 +3926,10 @@ static void irq_remapping_prepare_irte(struct amd_ir_data *data,
irte->fields.destination = irq_cfg->dest_apicid;
irte->fields.dm = apic->irq_dest_mode;
irte->fields.valid = 1;
+ if (info->type == X86_IRQ_ALLOC_TYPE_MSI)
+ pr_warn("irqdomain: IRTE%d vector %d APICID%d data%p cfg%p\n",
+ irte_info->index, irte->fields.vector,
+ irte->fields.destination, data, irq_cfg);
switch (info->type) {
case X86_IRQ_ALLOC_TYPE_IOAPIC:
@@ -3972,6 +3976,9 @@ static int irq_remapping_alloc(struct irq_domain *domain, unsigned int virq,
info->type != X86_IRQ_ALLOC_TYPE_MSIX)
return -EINVAL;
+ if (info->type == X86_IRQ_ALLOC_TYPE_MSI)
+ pr_warn("irqdomain: allocate %d MSI IRQ, VIRQ%d\n", nr_irqs, virq);
+
/*
* With IRQ remapping enabled, don't need contiguous CPU vectors
* to support multiple MSI interrupts.
@@ -3986,6 +3993,8 @@ static int irq_remapping_alloc(struct irq_domain *domain, unsigned int virq,
ret = irq_domain_alloc_irqs_parent(domain, virq, nr_irqs, arg);
if (ret < 0)
return ret;
+ if (info->type == X86_IRQ_ALLOC_TYPE_MSI)
+ pr_warn("irqdomain: allocate parent returns %d\n", ret);
ret = -ENOMEM;
data = kzalloc(sizeof(*data), GFP_KERNEL);
@@ -4005,6 +4014,8 @@ static int irq_remapping_alloc(struct irq_domain *domain, unsigned int virq,
kfree(data);
goto out_free_parent;
}
+ if (info->type == X86_IRQ_ALLOC_TYPE_MSI)
+ pr_warn("irqdomain: allocate IRTE index %d\n", index);
for (i = 0; i < nr_irqs; i++) {
irq_data = irq_domain_get_irq_data(domain, virq + i);
diff --git a/drivers/iommu/intel_irq_remapping.c b/drivers/iommu/intel_irq_remapping.c
index f15692a410c7..bb093bc6b334 100644
--- a/drivers/iommu/intel_irq_remapping.c
+++ b/drivers/iommu/intel_irq_remapping.c
@@ -1234,6 +1234,8 @@ static void intel_irq_remapping_prepare_irte(struct intel_ir_data *data,
MSI_ADDR_IR_SHV |
MSI_ADDR_IR_INDEX1(index) |
MSI_ADDR_IR_INDEX2(index);
+ if (info->type == X86_IRQ_ALLOC_TYPE_MSI)
+ pr_warn("irqdomain: allocate index%d, subhandle%d, irte%llx,%llx\n", index, sub_handle, irte->high, irte->low);
break;
default:
@@ -1305,6 +1307,8 @@ static int intel_irq_remapping_alloc(struct irq_domain *domain,
kfree(data);
goto out_free_parent;
}
+ if (info->type == X86_IRQ_ALLOC_TYPE_MSI)
+ pr_warn("irqdomain: allocate VIRQ%d, count%d, index%d\n", virq, nr_irqs, index);
for (i = 0; i < nr_irqs; i++) {
irq_data = irq_domain_get_irq_data(domain, virq + i);
--
1.7.10.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [Debug Patch] Collect more information about the regression
@ 2015-07-30 17:01 ` Jiang Liu
0 siblings, 0 replies; 15+ messages in thread
From: Jiang Liu @ 2015-07-30 17:01 UTC (permalink / raw)
To: Thomas Gleixner, Alexander Holler, Mark Rustad, Alex Deucher,
Joerg Roedel
Cc: Tony Luck, x86-DgEjT+Ai2ygdnm+yROfE0A,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
iommu-cunTk1MwBs9QetFLy7KEm3xJsTq8ys+cHZ5vskTnxNA, Tejun Heo,
Jiang Liu
Hi Alexander, Mark, Alex,
Could you please help to apply the debug patch and send me back
the dmesg? Please also help to turn kernel paramemter "apic=debug".
Hi Mark,
It seems that this regression is caused by support of multiple-MSI,
but I have no PCI card supportting multiple-MSI at hand. So may I remotely
access your system from Intel internal network? That will definitely speed
up fix.
Thanks!
Gerry
Signed-off-by: Jiang Liu <jiang.liu-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>
---
drivers/iommu/amd_iommu.c | 15 +++++++++++++--
drivers/iommu/intel_irq_remapping.c | 4 ++++
2 files changed, 17 insertions(+), 2 deletions(-)
diff --git a/drivers/iommu/amd_iommu.c b/drivers/iommu/amd_iommu.c
index a57e9b749895..c039ed9333a4 100644
--- a/drivers/iommu/amd_iommu.c
+++ b/drivers/iommu/amd_iommu.c
@@ -3916,8 +3916,8 @@ static void irq_remapping_prepare_irte(struct amd_ir_data *data,
union irte *irte = &data->irte_entry;
struct IO_APIC_route_entry *entry;
- data->irq_2_irte.devid = devid;
- data->irq_2_irte.index = index + sub_handle;
+ irte_info->devid = devid;
+ irte_info->index = index + sub_handle;
/* Setup IRTE for IOMMU */
irte->val = 0;
@@ -3926,6 +3926,10 @@ static void irq_remapping_prepare_irte(struct amd_ir_data *data,
irte->fields.destination = irq_cfg->dest_apicid;
irte->fields.dm = apic->irq_dest_mode;
irte->fields.valid = 1;
+ if (info->type == X86_IRQ_ALLOC_TYPE_MSI)
+ pr_warn("irqdomain: IRTE%d vector %d APICID%d data%p cfg%p\n",
+ irte_info->index, irte->fields.vector,
+ irte->fields.destination, data, irq_cfg);
switch (info->type) {
case X86_IRQ_ALLOC_TYPE_IOAPIC:
@@ -3972,6 +3976,9 @@ static int irq_remapping_alloc(struct irq_domain *domain, unsigned int virq,
info->type != X86_IRQ_ALLOC_TYPE_MSIX)
return -EINVAL;
+ if (info->type == X86_IRQ_ALLOC_TYPE_MSI)
+ pr_warn("irqdomain: allocate %d MSI IRQ, VIRQ%d\n", nr_irqs, virq);
+
/*
* With IRQ remapping enabled, don't need contiguous CPU vectors
* to support multiple MSI interrupts.
@@ -3986,6 +3993,8 @@ static int irq_remapping_alloc(struct irq_domain *domain, unsigned int virq,
ret = irq_domain_alloc_irqs_parent(domain, virq, nr_irqs, arg);
if (ret < 0)
return ret;
+ if (info->type == X86_IRQ_ALLOC_TYPE_MSI)
+ pr_warn("irqdomain: allocate parent returns %d\n", ret);
ret = -ENOMEM;
data = kzalloc(sizeof(*data), GFP_KERNEL);
@@ -4005,6 +4014,8 @@ static int irq_remapping_alloc(struct irq_domain *domain, unsigned int virq,
kfree(data);
goto out_free_parent;
}
+ if (info->type == X86_IRQ_ALLOC_TYPE_MSI)
+ pr_warn("irqdomain: allocate IRTE index %d\n", index);
for (i = 0; i < nr_irqs; i++) {
irq_data = irq_domain_get_irq_data(domain, virq + i);
diff --git a/drivers/iommu/intel_irq_remapping.c b/drivers/iommu/intel_irq_remapping.c
index f15692a410c7..bb093bc6b334 100644
--- a/drivers/iommu/intel_irq_remapping.c
+++ b/drivers/iommu/intel_irq_remapping.c
@@ -1234,6 +1234,8 @@ static void intel_irq_remapping_prepare_irte(struct intel_ir_data *data,
MSI_ADDR_IR_SHV |
MSI_ADDR_IR_INDEX1(index) |
MSI_ADDR_IR_INDEX2(index);
+ if (info->type == X86_IRQ_ALLOC_TYPE_MSI)
+ pr_warn("irqdomain: allocate index%d, subhandle%d, irte%llx,%llx\n", index, sub_handle, irte->high, irte->low);
break;
default:
@@ -1305,6 +1307,8 @@ static int intel_irq_remapping_alloc(struct irq_domain *domain,
kfree(data);
goto out_free_parent;
}
+ if (info->type == X86_IRQ_ALLOC_TYPE_MSI)
+ pr_warn("irqdomain: allocate VIRQ%d, count%d, index%d\n", virq, nr_irqs, index);
for (i = 0; i < nr_irqs; i++) {
irq_data = irq_domain_get_irq_data(domain, virq + i);
--
1.7.10.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: ATA failure regression in kernel 4.2
2015-07-28 18:37 ` Alexander Holler
2015-07-30 17:01 ` Jiang Liu
@ 2015-07-31 10:38 ` Alexander Holler
2015-07-31 10:42 ` Jiang Liu
1 sibling, 1 reply; 15+ messages in thread
From: Alexander Holler @ 2015-07-31 10:38 UTC (permalink / raw)
To: Alex Deucher, Jiang Liu; +Cc: Tejun Heo, LKML
Am 28.07.2015 um 20:37 schrieb Alexander Holler:
> Same problem here with the AMD SATA controller (1022:7801). It failed to
> identify the second disk when using 4.2-rc4.
>
> nointremap helped, nothing else tested
A quick look at the change history and two tests are suggesting that the
right one already is in cc.
commit
f7fa7ae x86/irq: Avoid memory allocation in __assign_irq_vector()
fails while
af87bae x86/htirq: Use new irqdomain interfaces to allocate/free IRQ
works. Inbetween almost all changes are from Jiang Liu.
Haven't bisected it up to now but might do it later.
> Regards,
>
> Alexander Holler
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: ATA failure regression in kernel 4.2
2015-07-31 10:38 ` ATA failure regression in kernel 4.2 Alexander Holler
@ 2015-07-31 10:42 ` Jiang Liu
2015-07-31 18:59 ` Alexander Holler
0 siblings, 1 reply; 15+ messages in thread
From: Jiang Liu @ 2015-07-31 10:42 UTC (permalink / raw)
To: Alexander Holler, Alex Deucher; +Cc: Tejun Heo, LKML
On 2015/7/31 18:38, Alexander Holler wrote:
> Am 28.07.2015 um 20:37 schrieb Alexander Holler:
>
>> Same problem here with the AMD SATA controller (1022:7801). It failed to
>> identify the second disk when using 4.2-rc4.
>>
>> nointremap helped, nothing else tested
>
> A quick look at the change history and two tests are suggesting that the
> right one already is in cc.
>
> commit
>
> f7fa7ae x86/irq: Avoid memory allocation in __assign_irq_vector()
>
> fails while
>
> af87bae x86/htirq: Use new irqdomain interfaces to allocate/free IRQ
>
> works. Inbetween almost all changes are from Jiang Liu.
>
> Haven't bisected it up to now but might do it later.
Hi Alexander,
Really thanks for you help. I have debugged this regression
for a whole day without any progress:( Everything seems correct to me,
and I have no hardware to reproduce and debug it. Still need more time:(
Thanks!
Gerry
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: ATA failure regression in kernel 4.2
2015-07-31 10:42 ` Jiang Liu
@ 2015-07-31 18:59 ` Alexander Holler
0 siblings, 0 replies; 15+ messages in thread
From: Alexander Holler @ 2015-07-31 18:59 UTC (permalink / raw)
To: Jiang Liu, Alex Deucher; +Cc: Tejun Heo, LKML
Am 31.07.2015 um 12:42 schrieb Jiang Liu:
>
>
> On 2015/7/31 18:38, Alexander Holler wrote:
>> Am 28.07.2015 um 20:37 schrieb Alexander Holler:
>>
>>> Same problem here with the AMD SATA controller (1022:7801). It failed to
>>> identify the second disk when using 4.2-rc4.
>>>
>>> nointremap helped, nothing else tested
>>
>> A quick look at the change history and two tests are suggesting that the
>> right one already is in cc.
>>
>> commit
>>
>> f7fa7ae x86/irq: Avoid memory allocation in __assign_irq_vector()
>>
>> fails while
>>
>> af87bae x86/htirq: Use new irqdomain interfaces to allocate/free IRQ
>>
>> works. Inbetween almost all changes are from Jiang Liu.
>>
>> Haven't bisected it up to now but might do it later.
> Hi Alexander,
> Really thanks for you help. I have debugged this regression
> for a whole day without any progress:( Everything seems correct to me,
> and I have no hardware to reproduce and debug it. Still need more time:(
> Thanks!
> Gerry
>
There's nothing to excuse. It wasn't a flame, just a determination. I'm
sorry if it might have sounded like a flame. Only people which are doing
nothing don't make failures, and doing nothing often is a failure
itself. But I'm drifting aways.
I've now bisected those commits I've had already identified by other
means down to the commit 52f518a3a7c2f80551a38d38be28bc9f335e713c
"x86/MSI: Use hierarchical irqdomains to manage MSI interrupts".
That is the one where 4.2-rc* fails here first.
Regards,
Alexander Holler
^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2015-07-31 18:59 UTC | newest]
Thread overview: 15+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-07-23 17:48 ATA failure regression in kernel 4.2 Alex Deucher
2015-07-23 18:35 ` Tejun Heo
2015-07-23 18:44 ` Alex Deucher
2015-07-24 17:38 ` Alex Deucher
2015-07-27 3:01 ` Jiang Liu
2015-07-27 15:21 ` Alex Deucher
2015-07-27 16:30 ` Jiang Liu
2015-07-27 17:36 ` Alex Deucher
2015-07-28 18:19 ` Alex Deucher
2015-07-28 18:37 ` Alexander Holler
2015-07-30 17:01 ` [Debug Patch] Collect more information about the regression Jiang Liu
2015-07-30 17:01 ` Jiang Liu
2015-07-31 10:38 ` ATA failure regression in kernel 4.2 Alexander Holler
2015-07-31 10:42 ` Jiang Liu
2015-07-31 18:59 ` Alexander Holler
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.